Honeywell 5S-5S000-3 User's Guide

MS7580 Genesis™
Presentation Area Imager
Installation and User’s Guide
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in
specifications and other information contained in this document without prior
notice, and the reader should in all cases consult HII to determine whether any
such changes have been made. The information in this publication does not
represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained
herein: nor for incidental or consequential damages resulting from the furnishing,
performance, or use of this manual.
This document contains propriety information that is protected by copyright.
All rights reserved. No part of this document may be photocopied, reproduced,
or translated into another language without the prior written consent of HII.
© 2009 Honeywell International Inc. All rights reserved.
Web Address: www.honeywellaidc.com
Trademarks
Omniplanar, Swiftdecoder, Metrologic, MetroSet2, EasyID, and TotalFreedom
are trademarks or registered trademarks of Metrologic Instruments, Inc. or
Honeywell International Inc.
Microsoft, Windows 95, and Windows are registered trademarks of Microsoft
Corporation.
IBM is a trademark of International Business Machines Corporation.
Checkpoint is a registered trademark of Checkpoint Systems, Inc.
Other product names mentioned in this manual may be trademarks or
registered trademarks of their respective companies and are the property of their
respective owners.
Patents
Refer to page 53 for a list of patents.
Table of Contents
Introduction
Product Overview ............................................................................................. 1
Base Kit Components....................................................................................... 2
Optional Accessories........................................................................................ 2
MS7580 Components....................................................................................... 4
Labels............................................................................................................... 5
Maintenance..................................................................................................... 5
Cable Installation and Removal........................................................................ 6
Interface Installation
RS232 .............................................................................................................. 7
Keyboard Wedge.............................................................................................. 8
RS485 .............................................................................................................. 9
USB ................................................................................................................ 10
Mounting the MS7580
Components of Adapter Kit 46-00911 ............................................................ 13
Components of Wall Mount Kit 46-00913 ....................................................... 13
Installation of Adapter Kit 46-00911 ............................................................... 14
Installation of Wall Mount Kit 46-00913 .......................................................... 16
Operation
Modes of Operation ........................................................................................ 17
Audible Indicators........................................................................................... 19
Visual Indicators ............................................................................................. 20
Failure Modes................................................................................................. 21
Field of View................................................................................................... 22
Depth of Field by Minimum Bar Code Element Width .................................... 23
IR Activation Range........................................................................................ 24
Troubleshooting Guide.........................................................................25
Design Specifications...........................................................................29
iii
Applications and Protocols..................................................................31
Configuration and Upgrades................................................................33
Configuration Modes ...................................................................................... 33
Upgrading the Firmware ................................................................................. 33
MS7580-118-EAS Model
Integrated RF EAS Antenna Connection ........................................................ 35
EAS System Connection ................................................................................ 36
Configuration for EAS Applications ................................................................ 37
EAS Tag Deactivation Range......................................................................... 39
Imager Pinouts–MS7580-118-EAS ................................................................ 41
Cable Pinouts ................................................................................................. 42
Antenna Disconnect ....................................................................................... 42
Imager and Cable Terminations
Standard Imager Pinouts................................................................................ 43
Standard Cable Pinouts.................................................................................. 44
Limited Warranty...................................................................................47
Regulatory Compliance
Safety ............................................................................................................. 49
EMC ............................................................................................................... 50
Patents ...................................................................................................53
Index .......................................................................................................55
Contact Information ..............................................................................57
Product Service and Repair .................................................................59
iv
Introduction
Product Overview
The MS7580 Genesis™ is a high performance presentation area-imaging bar
code imager that utilizes high-resolution CMOS imaging sensors for superior
image quality. Genesis utilizes SwiftDecoder™ software, for reliable decoding of
both 1D and 2D bar code symbologies. Sharp images can be captured and
transmitted in a variety of outputs including: .jpg, .bmp, and .tiff.
Omnidirectional scanning capabilities and an excellent motion tolerance provides
aggressive scanning of all standard 1D, GS1 DataBar™ (RSS), PDF417,
microPDF, Composite, Matrix, and Postal Codes symbology types. Firmware
updates are easily loaded into Flash memory.
The MS7580 provides an extended scan volume and a built in object detection
sensor (IR) that instantly turns on the imager when an object is presented within
the imager’s field of view.
Genesis™
Interface Support
Interfaces supported include:
MS7580–118
•
RS232
•
RS485
•
USB
•
Keyboard Wedge

EAS equipped models are indicated with an EAS extension on the model number
(i.e., MS7580-118-EAS). See pages 35–42 for additional product information.

USB is configurable for Keyboard Emulation Mode, Bi-Directional Serial Emulation
Mode or IBM OEM. The default USB setting is Keyboard Emulation Mode.

Applicable for IBM host applications.
®
Note: Standard models ship with the ability to read all 1D, PDF, and 2D bar
codes. Decoding and functional capability is limited and imagers will
not support key features including, but not limited to, the ability to
decode PDF, 2D or OCR fonts without proper limited use licenses
provided by Honeywell. If you wish to purchase a limited license for one
or more of the key features not included in the standard imager, please
specify at the time of sale or otherwise contact a customer service
representative for more information.
1
Base Kit Components
Part #
Description
MS7580-118
MS7580 Genesis Presentation Area Imager
00-02544
MetroSelect® Single-Line Configuration Guide
00-05252
Area-Imaging Supplemental Configuration Guide*
00-02290
MS7580 Genesis Presentation Area Imager
Installation and User’s Guide*


EAS equipped models are indicated with an EAS extension on the model number
(i.e., MS7580-118-EAS). See pages 35–42 for additional product information.
Manuals are available for download from www.honeywellaidc.com.
Optional Accessories
Part #
Description
AC to DC Power Transformer - Regulated 12VDC @ 1.25A output.
46-00862
90VAC to 255VAC United States, Canada and Japan
46-00863
90VAC to 255VAC Continental European
46-00864
90VAC to 255VAC United Kingdom
46-00865
90VAC to 255VAC China
46-00866
90VAC to 255VAC Australia
Other items may be ordered for the specific protocol being used. To order additional items,
contact the dealer, distributor, or customer service. See page 57 for contact information.
2
Part #
Description
Cable Compatibility Warning
The MS7580 requires a cable designed for a 12VDC area imager.
Do not attempt to use any cables other than the specified cables listed below
(cable series 5S-5Sxxx). Any damage incurred from incorrect cable usage
will void the limited warranty shown on page 47.
5S-5S000-3
RS232 12V VLink Cable with Built in Power Jack
Straight Black Cable with Short Strain Relief
5S-5S002-3
Keyboard Wedge 12V VLink Cable with Adapter Cable
Straight Black Cable with Short Strain Relief
5S-5S006-N-3
RS485, Direct Cable for 12V Host Power
Straight Black Cable with Short Strain Relief
5S-5S213-N-3
USB Direct Cable for 12V Host Power
Locking Plus-Power™ Type A Connector
Straight Black Cable with Short Strain Relief
5S-5S235-3
USB 12V VLink Cable with Built in Power Jack
Non-Locking Type A Connector
Straight Black Cable with Short Strain Relief
The following MS7580-118-EAS cables are compatible with Checkpoint®
System devices. For additional cable information for the MS7580-118-EAS,
refer pages 35–42.
MX-5S000-E-3
RS232 12V VLink Straight, Black Cable
with Built in Power Jack
MX-5S235-E-3
USB 12V VLink Straight Black Cable with
Built in Power Jack, Non-Locking Type A Connector
46-00911
MS7580 Wall Mount Adapter Kit
46-00913
MS7580 Wall Mount Kit
00-05250
MS7580 Wall Mount Installation Guide
Other items may be ordered for the specific protocol being used. To order additional items,
contact the dealer, distributor, or customer service. See page 57 for contact information.
3
MS7580 Components
Item
Item Description
1
Blue and White LED
See Visual Indicators (on page 20)
2
Button
Mode Select Button
3
Speaker
See Audible Indicators (on page 19)
4
Window
LED Aperture
5
Adjustable Base
6
Cable Connection
10-pin RJ45, Female Socket,
See Imager Pinout Connections (on page 43)
7
Cable Release
See Cable Installation and Removal (on page 6)
Note: The MS7580-118-EAS model is equipped with an integrated antenna
for Electronic Article Surveillance (EAS) system support. See pages
35–42 for additional product information.
Figure 1. Imager Components
4
Labels
Each MS7580 has a label located near the top of the output window. This label
provides the imager’s model number, date of manufacture, serial number, CE
and caution information. Additional information has been molded into the
underside of the imager's case. The following figure gives an example of the
label and the molded text with their locations identified.
Figure 2. Label and Molded Text Samples
Caution: To maintain compliance with applicable standards, all circuits connected to
the imager must meet the requirements for SELV (Safety Extra Low Voltage)
according to EN/IEC 60950-1.
To maintain compliance with standard CSA C22.2 No. 60950-1/UL 60950-1
and norm EN/IEC 60950-1, the power source should meet applicable
performance requirements for a limited power source.
Maintenance
Smudges and dirt on the imager's window can interfere with the imager's
performance. If the window requires cleaning, use only a mild glass cleaner
containing no ammonia. When cleaning the window, spray the cleaner onto a lint
free, non-abrasive cleaning cloth then gently wipe the window clean.
If the imager's case requires cleaning, use a mild cleaning agent that does not
contain strong oxidizing chemicals. Strong cleaning agents may discolor or
damage the imager's exterior.
5
Cable Installation and Removal
Installation
1.
Insert the cable’s modular connector into the socket on the imager.
2.
Pull gently on the cable strain relief to ensure the cable is installed.
Note: If the cable is not fully latched, the imager may power intermittently.
Figure 3. Installing the Cable
Removal
Turn the host power off and disconnect the power supply from the cable before
attempting to disconnect the cable from the imager.
1.
Locate the small pinhole on the imager near the cable connection point.
2.
Bend a paperclip into the shape shown below.
3.
Insert the paperclip into the pinhole and apply pressure to release the
connector lock.
4.
Pull gently on the strain-relief of the cable to remove the cable from the
imager.
Figure 4. Disconnecting the Cable
MS7580-118-EAS Model Note
See page 35 for additional cable installation/removal instructions specific to the
MS7580-118-EAS Genesis with integrated RF EAS antenna.
6
Interface Installation
RS232
1.
Turn off power to the host device.
2.
Plug the interface cable’s modular
connector into the socket on the imager.
3.
Connect the other end of the cable to a
dedicated COM port on the host device.
4.
Plug the 12V power supply into the
power jack on the cable.
5.
Check the AC input requirements
of the power supply to verify the voltage
matches the AC outlet. The outlet must
be located near the equipment and
easily accessible.
6.
Connect AC power to the transformer.
7.
The MS7580 will start to initialize.
The white and blue LED will alternately
fade on and off for three seconds.
When the imager has finished
initializing, the imager will flash the white
LED three times while simultaneously
beeping three times. The low intensity
blue LED will remain turned on.
8.
Turn on power to the host device.
Figure 5. RS232
See caution on page 5.
Installation Notes

•
MS7580-118-EAS models are equipped with an integrated RF EAS
antenna. See page 35 for additional cable installation instructions for
EAS equipped Genesis models.
•
Plugging the imager into a port on the host system does not guarantee
that scanned information will be communicated properly to the host
system. The imager is shipped from the factory configured with default
settings. Please refer to the MetroSelect Single-Line Configuration
Guide (PN 00-02544) or MetroSet2’s help files for instructions on
changing the imager’s configuration. In addition, please check that the
imager and host system are using the same communication protocol.
The MS7580 requires 12V power to function for RS232 operation. Honeywell
recommends using the external power supply shipped with the MS7580.
7
Keyboard Wedge
1.
Turn off power to the host device.
2.
Plug the interface cable’s modular
connector into the socket on the imager.
3.
Disconnect the keyboard from the
host device.
4.
Connect the “Y” ends of the
communication cable to the keyboard
and the keyboard port on the host
device. A male/female adapter cable is
supplied with the imager kit.
5.
Plug the 12V power supply into the
power jack on the cable.
6.
Check the AC input requirements of the
power supply to verify the voltage
matches the AC outlet. The outlet must
be located near the equipment and be
easily accessible.
7.
Connect AC power to the transformer.
8.
The MS7580 will start to initialize. The
white and blue LED will alternately fade
on and off for three seconds. When the
imager has finished initializing, the
imager will flash the white LED three
times while simultaneously beeping
three times. The low intensity blue LED
will remain turned on.
9.
Figure 6. Keyboard Wedge
See caution on page 5.
Turn on power to the host device.
Installation Note
Plugging the imager into a port on the host system does not guarantee that
scanned information will be communicated properly to the host system. The
imager is shipped from the factory configured with default settings. Please refer
to the MetroSelect Single-Line Configuration Guide (PN 00-02544) or
MetroSet2’s help files for instructions on changing the imager’s configuration. In
addition, please check that the imager and host system are using the same
communication protocol.

8
The MS7580 requires 12V power to function for Keyboard Wedge operation.
RS485
1.
Turn off power to the host device.
2.
Plug the interface cable’s modular
connector into the socket on the imager.
3.
Connect the other end of the cable to
proper COM port of the host device.
4.
Turn on power to the host device.
5.
The MS7580 will start to initialize.
The white and blue LED will alternately
fade on and off for three seconds.
When the imager has finished
initializing, the imager will flash the white
LED three times while simultaneously
beeping three times. The low intensity
blue LED will remain turned on.
Figure 7. RS485
Installation Note
Plugging the imager into a port on the host system does not guarantee that
scanned information will be communicated properly to the host system.
The imager is shipped from the factory configured with default settings.
Please refer to the MetroSelect Single-Line Configuration Guide (PN 00-02544)
or MetroSet2’s help files for instructions on changing the imager’s configuration.
In addition, please check that the imager and host system are using the same
communication protocol.

The MS7580 requires 12V power from the host for RS485 operation.
9
USB
1.
Turn off power to the host device.
2.
Plug the interface cable’s modular
connector into the socket on the
imager.
3.
Plug the USB end of the cable into
the host’s USB port.
Steps 4–6 are for VLink cables with a
built in power jack and 12V external
power supply. Skip to step 6 for USB
direct connect cables receiving 12V
power from the host.
4.
Plug the power supply into the
power jack on the VLink cable.
5.
Check the AC input requirements
of the power supply to verify the
voltage matches the AC outlet.
The outlet must be located near the
equipment and be easily
accessible.
6.
Connect AC power to the transformer.
7.
Turn on power to the host device.
8.
The MS7580 will start to initialize. The
white and blue LED will alternately fade
on and off for three seconds. When the
imager has finished initializing, the
imager will flash the white LED three
times while simultaneously beeping
three times. The low intensity blue LED
will remain turned on.
Figure 8. USB
See caution on page 5.
Installation Notes

10
•
MS7580-118-EAS models are equipped with an integrated RF EAS
antenna. See page 35 for additional installation instructions for MS7580118-EAS models.
•
The MS7580 meets the requirements for Full Speed USB hardware.
The USB interface is configurable for Keyboard Emulation Mode,
Bi-Directional Serial Emulation Mode or IBM OEM. The default setting
for the USB interface is Keyboard Emulation Mode.
The MS7580 requires 12V power from the host for pass-through capabilities to function.
See page 3 for a complete list of USB cable options.
•
For information on configuring the MS7580 for USB Serial Emulation
Mode or IBM OEM, refer to the USB section of the MetroSelect
Single-Line Configuration Guide (PN 00-02544).
•
Plugging the imager into a port on the host device does not guarantee
that scanned information will be communicated properly to the host
device. The imager is shipped from the factory configured with default
settings. Please refer to the MetroSelect Single-Line Configuration
Guide (PN 00-02544) or MetroSet2’s help files for instructions on
changing the imager’s configuration. In addition, please check that the
imager and host system are using the same communication protocol.
11
12
Mounting the MS7580
Components of Adapter Kit 46-00911
Item
Item Description
Qty.
A
Adapter Plate
1
B
Locking Plate
1
C
Base Cover
1
D
M3 x .5 - 10 mm Flat Head Phillips Screw
4
E
M3 x .5 - 8 mm Flat Head Phillips Screw
4
F
#7 x 1.00 in. FHP Wood Screw
3
G
MS7580 Wall Mount Installation Guide
1
Figure 9. 46-00911 Kit Components
Components of Wall Mount Kit 46-00913
Item
Item Description
Qty.
A
Wall Mount
1
B
#7 x 1.00 in. FHP Wood Screw
2
C
MS7580 Wall Mount Installation Guide
1
Figure 10. 46-00913 Kit Components
13
Installation of Adapter Kit 46-00911
1.
Remove the rubber feet on the bottom of the MS7580.
2.
Attach the adapter plate to the bottom of the imager with the four
M3 x .5 x 10 mm screws (  ) provided in the kit.
3.
Attach the base plate to the adapter plate with the four M3 x .5 x 8 mm
screws (  ) provided in the kit.
4.
Before mounting the locking plate, consider the position the imager will rest
when fully installed. There are two tabs located on the locking plate.
These tabs indicate the two directions the imager may face when locked
into position (see figure below).
Figure 11
Figure 12
14
5.
Use the locking plate as a guide to drill three #39 pilot holes (A) in the
mounting surface.
Figure 13. Locking Plate (Not Drawn to Scale)
6.
Secure the locking plate to the wall with the three #7 wood screws ()
provided in the kit.
Figure 14
7.
Position the imager so the base plate sits flush over the locking plate.
Twist the imager 90° counter-clockwise to lock the imager into place.
Figure 15
15
Installation of Wall Mount Kit 46-00913
1.
Drill two #39 pilot holes in the mounting surface. The pilot holes should be
centered vertically 44 mm apart.
2.
Position the wall mount over the pilot holes with the arrow pointing up.
3.
Secure the wall mount to the wall with the two #7 wood screws () provided
in the kit.
Figure 16
4.
Slide the imager's base under the upper corner tabs on the wall mount.
5.
Slide the remainder of the base in and down behind the lower corner tabs.
Figure 17
16
Operation
Modes of Operation
The MS7580 supports two standard modes of operation for scanning bar codes,
automatic activation and manual activation scanning. Scanning while in the
automatic activation mode can occur in either one of two configurable options,
pass-through or presentation. Both the pass-through and the presentation
options are enabled by default. With the default configuration, the imager
operates in the pass-through state for 300 ms and then changes to the
presentation state for additional decoding capability.
Automatic Activation Mode
Pass-through Scanning–The imager decodes only 1D and PDF bar codes.
Scanning method:
1.
Pass the bar code through the active scan area to scan, decode and
send data.
Presentation Scanning–The imager decodes all 1D, PDF and 2D matrix codes
Scanning method:
1.
Place the object in the IR activation range.
2.
Hold the object's bar code in front of the scan window within the active
scan area to scan, decode and send data.
Manual Activation
The imager decodes all 1D, PDF and 2D matrix codes
Scanning method:
1.
Press the button one time to activate linear targeting.
2.
Press the button one time to activate linear targeting.

The MS7580 requires 12V power for pass-through capabilities to function.

The default configuration is recommended for optimum scan performance.

Imager configuration bar codes require the manual activation mode.

2D matrix bar codes types are not enable by default in the manual activation mode.
Refer to the Area-Imaging Supplemental Configuration Guide (see page 3) for
additional information on enabling code types.
17
3.
Press the button one time to activate linear targeting.
4.
Align the linear targeting line over the desired bar code.
Note: When scanning 1D bar codes, the bar code must be presented to
the imager in the correct orientation, see Figure 18. PDF and 2D
matrix codes may be presented in any orientation.
Figure 18. 1D Bar Code Orientation
5.
Press button a second time to decode and send the data
6.
The imager will return to the default presentation mode by either the
default time length or by double pressing the button.
Note: Decoding and functional capability of the imager is restricted through the
use of license numbers provided by Honeywell. Imagers will not support
key features such as, but not limited to, the ability to decode PDF, 2D or
OCR fonts without proper licenses. If you wish to purchase a limited
license for one or more of the key features not included in the standard
imager, please specify at the time of sale or otherwise contact a customer
service representative for more information. Standard models ship with
the ability to read all 1D, PDF, and 2D bar codes. OCR fonts are disabled
by default and must be specifically requested at an additional cost.
18
Audible Indicators
The MS7580 provides audible feedback during operation. The audible feedback
indicates the status of the imager. Eight settings are available for the tone of the
beep (normal, 6 alternate tones and no tone). To change the tone, refer to the
MetroSelect Single-Line Configuration Guide, PN 00-02544 or MetroSet2’s
help files.
One Beep
When the imager successfully reads a bar code the imager will beep once and
the white LED will flash once indicating data has been transmitted successfully.
The blue LED will return to the low intensity state if no other objects are
presented in the active scan area.
If the imager does not beep once and the white light does not flash, then the bar
code has not been successfully read.
Short Razzberry Tone
This tone is a failure indicator (see Failure Modes on page 21).
Long Razzberry Tone
This tone is a failure indicator (see Failure Modes on page 21).
Three Beeps - At Power Up
When the MS7580 first receives power it will start an initialization sequence.
The white and blue LEDs will alternately fade on and off for approximately
3 seconds. When the imager has finished initializing the white LED will flash
three times while simultaneously beeping three times to indicate the imager is
ready for use.
Three Beeps - Configuration Mode
When entering configuration mode, the white LED will flash while the imager
simultaneously beeps three times. The white and blue LEDs will continue to
flash while in this mode. Upon exiting configuration mode, the imager will beep
three times, and the LEDs will stop flashing.
When configured, 3 beeps can also indicate a communications timeout during
normal scanning mode.
When using single-code-configuring, the imager will beep three times:
a normal tone followed by a short pause, a high tone and then a low tone.
This indicates that the single configuration bar code has successfully configured
the imager.
19
Visual Indicators
The imager has blue and white LED
indicators surrounding the button on the
top of the imager. When the imager is on,
the intensity of the LED and the flashing or
stationary activity of the LEDs, indicates
the status of the current scan and the
diagnostic imager.
Figure 19.
No LEDs are Illuminated
The LEDs will not be illuminated if the imager is not receiving power from the
host or transformer.
Steady Low Intensity Blue
The imager is in stand-by mode. Present a bar code to the imager and the blue
LED will switch to a high intensity blue when the IR detects the object.
Steady High Intensity Blue
The high intensity blue LED is illuminated when the imager is active and
attempting to decode a barcode.
Single White Flash
When the imager successfully reads a bar code the imager will beep once and
the white LED will flash once indicating data has been transmitted successfully.
The blue LED will return to the low intensity state if no other objects are
presented in the active scan area.
If the imager does not beep once and the white light does not flash, then the bar
code has not been successfully read.
Steady White
When the imager successfully reads a bar code it will beep once and the white
LED will turn on indicating data is being transmitted.
Note: After a successful scan, the imager transmits the data to the host device.
Some communication modes require that the host inform the imager when
data is ready to be received. If the host is not ready to accept the
information, the imager’s white LED will remain on until the data can
be transmitted.
Alternating Flashing of Blue and White
This indicates the imager is in configuration mode. A short razzberry tone
indicates that an invalid bar code has been scanned while in this mode.
20
Failure Modes
Long Razzberry Tone – During Power Up
Failed to initialize or configure the imager. If the imager does not respond after
reconfiguration, return the imager for repair.
Short Razzberry Tone – During Scanning
An Invalid bar code has been scanned when in configuration mode.
21
Field of View
Figure 20. Field of View
22
Depth of Field by Minimum Bar Code Element Width
Minimum Bar Code Element Width
1D
mm
mils
PDF
A
B
C
D
F
.13
.19
.26
.33
.25
G
.4
5.0
7.5
10.4
13
10
16
Figure 21. Depth of Field by Minimum Bar Code Element Width
Note: Standard models ship with the ability to read all 1D, PDF and 2D bar
codes. Decoding and functional capability is limited and imagers will not
support key features including, but not limited to, the ability to decode
PDF, 2D or OCR fonts without proper limited use licenses provided by
Honeywell. If you wish to purchase a limited license for one or more of the
key features not included in the standard imager, please specify at the
time of sale or otherwise contact a customer service representative for
more information.
23
IR Activation Range
The MS7580 has a built in object detection sensor that instantly turns on the
imager when an object is presented within the imager’s IR Activation Area,
shown below.
Figure 22. IR Activation Area
24
Troubleshooting Guide
The following troubleshooting guide is for reference purposes only. Contact a
customer service representative or technical support representative to preserve
the limited warranty terms. See pages 57–59 for contact information.
All Interfaces
Symptoms
Possible Causes
Solution
No power is being
supplied to the
imager.
Check transformer, outlet, and
power strip. Make sure the cable
is plugged into the imager.
No power is being
supplied to the
imager from the host.
Some host systems cannot supply
enough current to power the
MS7580. A power supply may be
required.
There has been a
imager configuration
failure.
Contact a customer service
representative, if the imager will
not hold the saved configuration.
There has been a
diagnostic failure.
Contact a customer service
representative, if the imager will
not function.
Long Razz tone
when exiting
configuration
mode
There was a failure
saving the new
configuration.
Re-try to configure the imager.
Contact a customer service
representative if the imager will not
hold the saved configuration.
Long Razz tone
There is a scanning
mechanism failure.
Contact a customer service
representative.
Short Razz tone
in configuration
mode
An invalid bar code
has been scanned.
Scan a valid bar code or quit
configuration mode.
No LEDs, beep
or illumination
Long Razz tone
on power up
25
Symptoms
Possible Causes
Solution
The imager
powers up, but
The beeper is
does not beep
disabled and no tone
when bar code is is selected.
scanned.
Enable the beeper and select a
tone.
The imager
powers up, but
does not scan
and/or beep.
The bar code
symbology trying to
be scanned is not
enabled.
UPC/EAN, Code 39, interleaved 2
of 5, Code 93, Code 128, Codabar
and PDF are enabled by default.
Verify that the type of bar code
being read has been selected.
The imager
powers up, but
does not scan
and/or beep.
The imager is trying
to scan a barcode that
does not match the
configured criteria.
Verify that the bar code being
scanned falls into the configured
criteria (i.e. character length lock or
minimum bar code length settings).
The following item is only relevant for RS232 and Serial USB Interfaces.
The imager
scans a bar
code, but locks
up after the first
scan and the
white LED stays
on.
The imager is
configured to support
some form of host
handshaking but is not
receiving the signal.
If the imager is setup to support
ACK/NAK, RTS/CTS, or
XON/XOFF, verify that the host
cable and host are supporting the
handshaking properly.
The imager
scans, but the
data transmitted
to the host is
incorrect.
The imager’s data
format does not
match the host
system requirements.
Verify that the imager’s data
format matches that required by
the host. Make sure that the
imager is connected to the proper
host port.
26
Symptoms
The imager
beeps at some
bar codes and
NOT for others
of the same bar
code symbology.
The imager
scans the bar
code but there
is no data.
Possible Causes
Solution
The bar code may
have been printed
incorrectly.
Check if it is a check
digit/character/or border problem.
The imager is not
configured correctly
for this type of bar
code.
Check if check digits are set
properly.
The minimum symbol
length setting does
not work with the bar
code.
Check if the correct minimum
symbol length is set.
The configuration is
not set correctly.
Make sure the imager is configured
for the appropriate mode.
The next four items are only relevant for a Keyboard Wedge interface.
The imager
scans but the
data is not
correct.
The configuration is
not set correctly.
Make sure that the proper PC type
AT, or PS2 is selected. Verify
correct country code and data
formatting are selected. Adjust
inter-character delay symptom.
The imager is
The configuration is
transmitting each
not set correctly.
character twice.
Increase interscan code delay
setting. Adjust whether the F0
break is transmitted. It may be
necessary to try this in both
settings.
Alpha characters
The computer is in
show as lower
Caps Lock mode.
case.
Enable Caps Lock detect setting
of the imager to detect if the PC is
operating in Caps Lock.
Everything works
except for a
couple of
characters.
Try operating the imager in Alt
mode.
These characters
may not be supported
by that country’s key
look up table.
27
Symptoms
The imager
scans but the
data is not
correct.
Possible Causes
The imager and host
may not be configured
for the same interface
parameters.
Solution
Check that the imager and the
host are configured for the same
interface parameters.
The following item is only relevant for an RS232 interface.
The imager
Check to make sure that the baud
powers up OK
The com port at the
rate and parity of the imager and
and scans OK
host is not working or
the communication port match
but does not
not configured
and the program is looking for
communicate
properly.
“RS232” data.
properly with
the host.
The imager
powers up OK
and scans OK
but does not
communicate
properly with
the host.
The cable is not
connected to the
correct com port.
Check to make sure that the cable
is connected to the correct com
port.
Characters are
being dropped.
Inter-character delay
needs to be added to
the transmitted output.
Add some inter-character delay to
the transmitted output by using
the Configuration Guides
(PN 00-02544 and 00-05252).
The following item is only relevant for a USB interface.
The USB host may not
be active.
No LEDs, beep
or Illumination
The MS7580 will not
operate from hub/host
power without host
communication.
The imager is not
receiving sufficient
power to support
operation.
Refer to the electrical
specifications on page 30.
28
Turn on the host device.
Verify adequate power is being
supplied to the imager.
Design Specifications
Operational
Light Source:
LED 645 nm ±7.5 nm
Pulse Duration:
Up to 500μs (Default)
Maximum Output
of an Osram LED:
Depth of Scan Field:
Maximum 85 mA emits 3,120 mlm
0 mm – 152 mm (0" – 6") for 0.33 mm (13 mil)
55 mm x 35 mm (2.2" x 1.4") @ Face / Window
Field of View:
Minimum Element
Width:
Resolution:
Infrared Activation
Range:
Optional Decode and
Imaging Capabilities:
System Interfaces:
Print Contrast:
Number Characters
Read:
Beeper Operation:
185 mm x 110 mm (7.3" x 4.3") @ 152 mm (6") from
Face
1D
0.1 mm (4 mil)
2D
0.254 mm (10 mil)
1280 x 768 Pixels
0 mm (0") face to 152 mm to (6")
Autodiscriminates all Standard 1-D, RSS, PDF417,
microPDF, MaxiCode, Data Matrix, QR Code, UCC,
EAN Composites, Postals, Aztec
(Image Transfer) – BMP, TIFF, or JPEG output on
USB and RS232 Interfaces
PC Keyboard Wedge, RS232, RS485, USB
20% Minimum Reflectance Difference
4096 Bytes Maximum
7 tones or no beep
High Intensity Blue
Indicators (LED)
Default Settings:
The imager is active and attempting
to scan.
Low Intensity Blue The imager is idle.
White
Good Read
29
Mechanical
Height (H):
150 mm (5.91")
Width (W):
83 mm (3.27")
Depth (D):
80 mm (3.15")
Weight:
340 g (12 oz.)
Termination:
10 pin modular RJ45
Electrical
Input Voltage:
12VDC ± 0.25V
5VDC ± 0.25V
3.1 W (Typical)
2.0 W (Typical)
Operating
2.3 W (Typical)
1.8 W (Typical)
Idle
1.7 W (Typical)
1.6 W (Typical)

260 mA (Typical)
408 mA (Typical)
Operation
192 mA (Typical)
362 mA (Typical)
Idle
142 mA (Typical)
322 mA (Typical)
Peak
Current:

DC Transformer:
+5 Volt
USB Power Value

Peak
Power:
+12 Volt
Adapter Value
Peak Values of at least 1 ms in width.
Class 2; 12VDC @ 1.25 A
For regulatory compliance information see pages 49–52
Environmental
Temperature:
Humidity:
Light Levels:
Shock:
Contaminants:
Ventilation:
30
Operating = 0°C to 40° (32° to 104°F)
Storage = -40°C to 60°C (-40°F to 140°F)
0% to 95% Relative Humidity, Non-Condensing
Up to 50,000 Lux
Designed to withstand 1.5 m (5 ft.) drops
Sealed to resist airborne particulate contaminants
None required
Applications and Protocols
The model number on each imager includes the imager number and factory
default communications protocol.
Imager
Version Identifier
Communication Protocol(s)
Interfaces supported include:
MS7580
118
•
RS232 (TXD, RXD, RTS, CTS)
•
RS485
•
USB
•
Keyboard Wedge

TXD and RTS are transmitted at TTL levels. Contact a customer service
representative for information on additional RS232 options.

USB is configurable for Keyboard Emulation Mode, Bi-Directional Serial Emulation
Mode or IBM OEM. The default USB setting is Keyboard Emulation Mode.
The MS7580 with a built-in PC Keyboard Wedge interface is designed for
Keyboard emulation use only. Many RS232 configurable functions, available in
other Honeywell imagers, are also available as keyboard wedge functions.
The following are the most important selectable options specific to the keyboard
wedge.
Keyboard Type
•
•
*AT (includes IBM® PS2 models 50, 55, 60, 80)
IBM PS2 (includes models 30, 70, 8556)
Keyboard Country Type
•
•
•
•
•
*USA
Belgian
French
German
Hungarian
•
•
•
•
•
Italian
Japanese
Russian Cyrillic
Slovenian
Spanish
•
•
•
•
Swiss
Swedish/Finnish
Turkish
United Kingdom
* Indicates a default setting. For information on how to change the default
settings, refer to the help files in MetroSet2, the MetroSelect Single-Line
Configuration Guide or the Area-Imaging Supplemental Configuration Guide.
31
32
Configuration and Upgrades
Configuration Modes
The MS7580 has three modes of configuration.
•
Bar Codes
The MS7580 can be configured by scanning the bar codes included
in the MetroSelect Single-Line Configuration Guide or the Area-Imaging
Supplemental Configuration Guide. The manuals are available for download
at www.honeywellaidc.com.
•
MetroSet2
This user-friendly Windows®-based configuration program allows you to
simply ‘point-and-click’ at the desired imager options. MetroSet2 is available
for download at www.honeywellaidc.com.
•
Serial Programming
This mode of configuration is ideal for OEM applications. Serial
programming mode gives the end-user the ability to send a series of
commands using the serial port of the host system. The commands are
equivalent to the numerical values of the bar codes located in the
MetroSelect Single-Line Configuration Guide.
Upgrading the Firmware
The MS7580 is part of Honeywell’s line of imagers with flash upgradeable
firmware. The upgrade process requires, a new firmware file supplied to the
customer by a customer service representative and Honeywell’s MetroSet2
software. A personal computer running Windows® 95 or greater with an
available RS232 serial or USB port is required to complete the upgrade.
Note: Do not use the standard cable supplied with Keyboard Wedge or RS485
MS7580 interface kits for firmware upgrades. If using USB or RS232 for
the upgrade process, the standard USB or RS232 cable provided with the
imager can be used.


See Contact Information on page 57.
MetroSet2 is available for download, at no additional cost, from
www.honeywellaidc.com.
33
To upgrade the firmware in the MS7580:
1.
Plug the imager into a serial communication port on the host system.
2.
Start the MetroSet2 software.
3.
Click on the plus sign (+) next to POS Scanners to expand the supported
imager list.
4.
Choose the MS7580 Genesis from the list.
5.
Click on the Configure Genesis/7580 Scanner button.
6.
Choose Flash Utility from the options list located on the left side of the
screen.
7.
Click on the Open File button in the Flash Utility window.
8.
Locate and open the flash upgrade file.
9.
Select the COM port that the imager is connected to on the host system.
10. Verify the settings listed in the Flash Utility window.
11. Click on the Flash Imager button to begin the flash upgrade. A message
will appear on the screen when the upgrade is complete.
34
MS7580-118-EAS Model
MS7580-118-EAS models are equipped with an integrated antenna for Electronic
Article Surveillance (EAS) system support. The following information should be
used in conjunction with the manufacturer’s EAS system documentation for
successful integration of an MS7580-118-EAS Genesis.
Integrated RF EAS Antenna Connection
The following information is applicable for MS7580-118-EAS kits containing an
RS232, MX-5S000-E-3 cable or a USB, MX-5S235-E-3 cable.
1.
Locate the connector cover on the
bottom of the imager’s base.
2.
Remove the socket screw securing
the connector cover. A 1.5 mm hex
key is supplied.
3.
Remove the connector cover plate by
lifting up () the end and sliding the
cover to the left ().
4.
Insert the 2-pin box plug (A) into the
receptacle on the imager’s stand
(Figure 24).
5.
Insert the cable’s strain relief (B) into
the channel on the stand (Figure 24).
6.
Re-install the connector cover. Slide
the tab (C) on the cover into the
space between the box receptacle
and the stand (Figure 25).
7.
Figure 23.
Figure 24.
Install the socket screw (D) to secure
the cover to the stand (Figure 25).
Figure 25.
35
EAS System Connection
The following information should be used in conjunction with the manufacturer’s
documentation EAS system.
Checkpoint® EAS System Integration
Honeywell cables compatible with Checkpoint EAS systems include five
additional wires for device connection. Consult the table below for the
appropriate wire and terminal configuration.
Antenna and Interlock† Connection
Cable
(MX-5S000-E-3 or MX-5S235-E-3)
Wire Color
Solid Light Green
Solid Black
Red and White
Black and White
No Insulation/Shield
Wire Gauge
Thin
Thin
Thick
Thick
Checkpoint Device
Connection
INTLK + Terminal
INTLK - Terminal, GND
Antenna + Terminal
Antenna - Terminal
Antenna Shield
Type
Interlock
Antenna
† Interlock functionality requires specific EAS device settings. Consult the
manufacturer’s EAS system documentation for the appropriate switch and timing
potentiometer settings.
Inside the Checkpoint device, two switch banks set the deactivation antenna
tuning. The recommended settings for the switch banks are shown below.
See page 39 for tag deactivation guidelines.
Switch Bank Settings
SW1
Switches 1 - 6
SW2
OFF
Switches 1 - 6
Settings of 0pF to 47pF are recommended to achieve a maximum
deactivation range.
36
OFF
†
Configuration for EAS Applications
EAS support is disabled by default in the MS7580-118-EAS series. To enable
EAS support the imager must be configured for a system type and signal mode.
Follow the configuration sequence below to configure the imager for EAS
functionality.
1.
Scan the system type bar code below to enable EAS system support.
Enable Checkpoint System EAS Support
³
2.
3
3
7
2
2
0
Scan either the Enable Continuous Mode bar code or the Enable Regular
Mode bar code.
Regular Mode
In regular EAS mode, the imager will signal the EAS system to
activate immediately after the area imager successfully transmits a
bar code. The imager will also signal the EAS system to deactivate
after the configured EAS timeout expires.
Note: If regular mode is enabled an EAS timeout length will need to
be configured (see page 38).
Enable Regular Mode
³
1
4
6
1
0
5
Continuous Mode
In continuous mode, the imager will signal the EAS system to activate
when it first powers on. The area imager will never deactivate the
EAS system while in continuous mode. The EAS timeout setting has
no effect in continuous mode.
Enable Continuous Mode
³
1
4
6
1
1
5
37
3.
Scan the desired EAS timeout length (applicable for regular mode only).
The EAS timeout length specifies the maximum time that the area imager
will leave the EAS interlock signal asserted following a successful scan. The
EAS timeout setting has no effect in continuous mode.
Note:
If the area imager routinely fails to deactivate EAS tags, increase the
value of the timeout setting.
EAS Timeout 100 ms
³
8
4
6
0
0
0
EAS Timeout 500 ms
³
8
4
6
0
5
0
EAS Timeout 1s
³
8
4
6
0
1
0
0
EAS Timeout 5s
³
To Disable EAS Support
Scan the bar code below to disable EAS support.
Disable EAS Support
³
38
3
3
7
2
0
0
8
4
6
0
5
0
0
EAS Tag Deactivation Range
Antenna Precaution
The integrated EAS antenna is built into the stand/base of the imager. Do not
enclose or rest the imager’s base in close proximity to dense metal. The metal
may interfere with the antenna decreasing the expected deactivation range.
Tag Storage Precaution
Do not store tags within 45.7 cm [18.0″] of the MS7580. Tags stored closer than
45.7 cm [18.0″] may be unintentionally deactivated. The precautionary area
includes storage areas located under the MS7580.
Deactivation Range
Proper tag deactivation requires the entire tag to pass through the expected tag
deactivation range indicated in figures 26 (below) and 27 (on page 40).
Figure 26. Expected Tag Deactivation Area (Side View)
39
Figure 27. Expected Tag Deactivation Area (Top View)
40
Imager Pinouts–MS7580-118-EAS
Figure 28. MS7580-118-EAS, 10-Pin Female Modular Socket
USB
RS232
Pin
1
2
3
4
5
6
7
8
9
10
SHELL
Function
Signal/Power Ground
CTS Input
RS232 Receive Input
No Connect
Reserved
RTS Output 
No Connect
RS232 Transmit Output 
+12V Power
Shield Ground
Signal/Power Ground
Pin
1
2
3
4
5
6
7
8
9
10
SHELL
Function
Signal/Power Ground
Tied to Pin 4 in Cable
No Connect
Tied to Pin 2 in Cable
Reserved
USB D+
+5VDC USB Power
USB D+12V Power
Shield Ground
Signal/Power Ground
Integrated RF EAS Antenna
(MS7580-118-EAS Models Only)
Pin
1
2


Function
EAS ANT EAS ANT +
Figure 29. 2-Pin Box Receptacle
USB requires 12V power for pass-through functionality.
Signals on Pin 6 and 8 are TTL full level RS232 output signals on MS7580-118-EAS
models.
41
Cable Pinouts (Host End)‡
RS232, 12V VLink Cable
MX-5S000-E-3
Pin
1
2
3
4
5
6
7
8
9
Function
Shield Ground
RS232 Transmit Output
RS232 Receive Input
No Connect
Power/Signal Ground
DSR
CTS Input
RTS Output
Host +12VDC
Figure 30. 9-Pin Female, D-Type
USB
MX-5S235-E-3
Pin
1
2
3
4
Function
PC +5V/V_USB
DD+
Ground
Figure 31. USB Type A, Non-Locking
Antenna Disconnect
Figure 32. Antenna Disconnect
1.
2.
3.
4.
Remove the connector cover on the bottom of the imager base.
Release the strain relief.
Press the release lock on the antenna connector.
Pull the connector free.
‡ MS7580-118-EAS compatible cables. For standard MS7580 cable pinouts refer
to page 44.
42
Imager and Cable Terminations
Standard Imager Pinouts‡
Figure 33. Back/Connector View of the MS7580
RS232
Pin
1
2
3
4
5
6
7
8
9
10
SHELL
Function
Signal/Power Ground
CTS/DTR Input
RS232 Receive Input
No Connect
No Connect
RTS Output 
No Connect
RS232 Transmit Output 
Adapter Power
Shield Ground
Signal/Power Ground
Keyboard Wedge
Pin
1
2
3
4
5
6
7
8
9
10
SHELL
RS485
Pin
1
2
3
4
5
6
7
8
9
10
SHELL



‡
Function
Signal/Power Ground
Tied to Pin 6 in Cable
No Connect
IBM A+
IBM BTied to Pin 2 in Cable
No Connect
No Connect
Adapter Power
Shield Ground
Signal/Power Ground
Function
Signal/Power Ground
Tied to Pin 3 in Cable
Tied to Pin 2 in Cable
PC Data
PC Clock
KB Clock
+5VDC PC Keyboard Power
KB Data
Adapter Power
Shield Ground
Signal/Power Ground
USB
Pin
1
2
3
4
5
6
7
8
9
10
SHELL
Function
Signal/Power Ground
Tied to Pin 4 in Cable
No Connect
Tied to Pin 2 in Cable
No Connect
USB D+
+5VDC USB Power
USB DAdapter Power
Shield Ground
Signal/Power Ground
RS485, RS232, and Keyboard Wedge interfaces require 12V power for operation.
USB requires 12V power for pass-through functionality.
Signals on Pin 6 and 8 are TTL level RS232 output signals.
See page 41 for pinout information specific to the MS7580-118-EAS Genesis model.
43
Standard Cable Pinouts‡ (Host End)
RS232, 12V VLink Cable
5S-5S000-3
Pin
Function
1
Shield Ground
2
RS232 Transmit Output
3
RS232 Receive Input
4
No Connect
5
Power/Signal Ground
6
Reserved
7
CTS Input
8
RTS Output
9
+12VDC
9-Pin Female, D-Type
RS485,
5S-5S006-N-3
Pin
Function
1
Signal/Power Ground
2
IBM A+
3
IBM B-
4
+12VDC
SDL A Key Connector
USB
5S-5S213-3 or 5S-5S006-N-3
Pin
Function
Type A
Non-Locking
Type A
Locking
Plus-Power
1
2
1
2
5S-5S213-3
USB Type A
Non-Locking
USB Type A
Locking Plus-Power
PC +5V/V_USB
D-
3
3
D+
4
4
Ground
5
Ground
6
+12VDC
7-8
5S-5S235-N-3
No Connect
‡ See page 42 for pinout information specific to the MS7580-118-EAS Genesis model.
44
Keyboard Wedge VLink Cable
5S-5S002-3
Pin
Function
1
Keyboard Clock
2
Keyboard Data
3
No Connect
4
Power Ground
5
+5VDC
Pin
1
5-Pin DIN, Female
Function
PC Data
2
No Connect
3
Power Ground
4
5
6
+5VDC
PC Clock
No Connect
6-Pin DIN, Male
Honeywell will supply an adapter cable with a 5-pin DIN male connector on one
end and a 6-pin mini DIN female connector on the other. According to the
termination required, connect the appropriate end of the adapter cable to the
VLink cable, leaving the necessary termination exposed for connecting to the
keyboard and the keyboard port on the PC.
Keyboard Wedge Adapter Cable
Supplied with Cable 5S-5S002-3
Pin
Function
1
PC Clock
2
PC Data
3
No Connect
4
Power Ground
5
+5VDC
Pin
5-Pin DIN, Male
Function
1
Keyboard Data
2
No Connect
3
Power Ground
4
+5VDC
5
Keyboard Clock
6
No Connect
6-pin Mini DIN, Female
45
46
Limited Warranty
Honeywell International Inc. ("HII") warrants its products and optional
accessories to be free from defects in materials and workmanship and to
conform to HII’s published specifications applicable to the products purchased at
the time of shipment. This warranty does not cover any HII product which is (i)
improperly installed or used; (ii) damaged by accident or negligence, including
failure to follow the proper maintenance, service, and cleaning schedule; or (iii)
damaged as a result of (A) modification or alteration by the purchaser or other
party, (B) excessive voltage or current supplied to or drawn from the interface
connections, (C) static electricity or electro-static discharge, (D) operation under
conditions beyond the specified operating parameters, or (E) repair or service of
the product by anyone other than HII or its authorized representatives.
This warranty shall extend from the time of shipment for the duration published
by HII for the product at the time of purchase ("Warranty Period"). Any defective
product must be returned (at purchaser’s expense) during the Warranty Period to
HII factory or authorized service center for inspection. No product will be
accepted by HII without a Return Materials Authorization, which may be obtained
by contacting HII. In the event that the product is returned to HII or its authorized
service center within the Warranty Period and HII determines to its satisfaction
that the product is defective due to defects in materials or workmanship, HII, at
its sole option, will either repair or replace the product without charge, except for
return shipping to HII.
EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE
FOREGOING WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR
WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR WRITTEN,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT.
HII’S RESPONSIBILITY AND PURCHASER’S EXCLUSIVE REMEDY UNDER
THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE
DEFECTIVE PRODUCT WITH NEW OR REFURBISHED PARTS. IN NO
EVENT SHALL HII BE LIABLE FOR INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, AND, IN NO EVENT, SHALL ANY LIABILITY
OF HII ARISING IN CONNECTION WITH ANY PRODUCT SOLD HEREUNDER
(WHETHER SUCH LIABILITY ARISES FROM A CLAIM BASED ON
CONTRACT, WARRANTY, TORT, OR OTHERWISE) EXCEED THE ACTUAL
AMOUNT PAID TO HII FOR THE PRODUCT. THESE LIMITATIONS ON
LIABILITY SHALL REMAIN IN FULL FORCE AND EFFECT EVEN WHEN HII
MAY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES,
LOSSES, OR DAMAGES. SOME STATES, PROVINCES, OR COUNTRIES DO
NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION
MAY NOT APPLY TO YOU.
47
All provisions of this Limited Warranty are separate and severable, which means
that if any provision is held invalid and unenforceable, such determination shall
not affect the validity of enforceability of the other provisions hereof. Use of any
peripherals not provided by the manufacturer may result in damage not covered
by this warranty. This includes but is not limited to: cables, power supplies,
cradles, and docking stations. HII extends these warranties only to the first endusers of the products. These warranties are non-transferable.
The duration of the limited warranty for the MS7580 is two (2) year(s). The
accessories have a 90 day limited warranty from the date of manufacture.
48
Regulatory Compliance
Safety
ITE Equipment
IEC 60950-1, EN 60950-1
LED
Class 1 LED Product: IEC 60825-1:1993+A1+A2, EN 60825-1:1994+A1+A2
Caution
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure. Under no
circumstances should the customer attempt to service the LED scanner. Never
attempt to look at the LED beam, even if the scanner appears to be
nonfunctional. Never open the scanner in an attempt to look into the device.
Doing so could result in hazardous radiation exposure. The use of optical
instruments with the LED equipment will increase eye hazard.
Atención
La modificación de los procedimientos, o la utilización de controles o ajustes
distintos de los especificados aquí, pueden provocar una exposición de luz
brillante peligrosa. Bajo ninguna circunstancia el usuario deberá realizar el
mantenimiento del LED (Diodo Emisor de Luz) del lector. Ni intentar mirar al haz
del LED incluso cuando este no esté operativo. Tampoco deberá abrir el lector
para examinar el aparato. El hacerlo puede conllevar una exposición peligrosa a
la luz del LED. El uso de instrumentos ópticos con el equipo LED puede
incrementar el riesgo para la vista.
Attention
L'emploi de commandes, réglages ou procédés autres que ceux décrits ici peut
entraîner de graves irradiations. Le client ne doit en aucun cas essayer
d'entretenir lui-même le scanner ou la LED. Ne regardez jamais directement le
rayon LED, même si vous croyez que le scanner est inactif. N'ouvrez jamais le
scanner pour regarder dans l'appareil. Ce faisant, vous vous exposez à un risque
d’irradiation. L'emploi d'appareils optiques avec cet équipement à LED augmente
le risque d'endommagement de la vision.
Achtung
Die Verwendung anderer als der hier beschriebenen Steuerungen, Einstellungen
oder Verfahren kann eine gefährliche Licht emittierender Dioden strahlung
hervorrufen. Der Kunde sollte unter keinen Umständen versuchen, den Licht
emittierender Dioden-Scanner selbst zu warten. Sehen Sie niemals in den Licht
emittierender Diodenstrahl, selbst wenn Sie glauben, daß der Scanner nicht aktiv
ist. Öffnen Sie niemals den Scanner, um in das Gerät hineinzusehen.
49
Wenn Sie dies tun, können Sie sich einer gefährlichen Licht emittierender
Diodenstrahlung aussetzen. Der Einsatz optischer Geräte mit dieser
Laserausrüstung erhöht das Risiko einer Sehschädigung.
Attenzione
L'utilizzo di sistemi di controllo, di regolazioni o di procedimenti diversi da quelli
descritti nel presente Manuale può provocare delle rischiose esposizioni
radiattive. Il cliente non deve assolutamente tentare di riparare egli stesso lo
scanner LED (o diodo emettitore di luce). Non guardate mai il raggio LED (d.
emettitore di luce), anche se credete che lo scanner non sia attivo. Non aprite
mai lo scanner per guardare dentro l'apparecchio. Facendolo potete esporVi ad
una radiazione rischiosa. L'uso di apparecchi ottici, equipaggiati con raggi LED
(d. emettitori di luce), aumenta il rischio di danni alla vista.
EMC
Emissions
FCC Part 15, ICES-003, CISPR 22, EN 55022
Immunity
CISPR 24, EN 55024
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Class A Devices
The following is applicable when the scanner cable is greater in length than
3 meters (9.8 feet) when fully extended:
Les instructions ci-dessous s’appliquent aux cables de scanner dépassant
3 métres (9.8 pieds) de long en extension maximale:
Folgendes trifft zu, wenn das Scannerkabel länger als 3 Meter ist:
This equipment has been tested and found to comply with limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the
interference at their own expense. Any unauthorized changes or modifications to
this equipment could void the user’s authority to operate this device.
50
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Notice
This Class A digital apparatus complies with Canadian ICES-003.
Remarque
Cet appareil numérique de classe A est conforme à la norme
canadienne NMB-003.
European Standard
Warning
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Funkstöreigenschaften nach EN55022:1998
Warnung!
Dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im Wohnbereich
Funkstörungen verursachen. In diesem Fall kann vom Betreiber verlangt werden,
angemessene Massnahmen durchzuführen.
Standard Europeo
Attenzione
Questo e’ un prodotto di classe A. Se usato in vicinanza di residenze private
potrebbe causare interferenze radio che potrebbero richiedere all’utilizzatore
opportune misure.
Attention
Ce produit est de classe “A”. Dans un environnement domestique, ce produit
peut être la cause d’interférences radio. Dans ce cas l’utiliseteur peut être
amené à predre les mesures adéquates.
51
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Class B Devices
The following is applicable when the scanner cable is less than 3 meters
(9.8 feet) in length when fully extended:
Les instructions ci-dessous s’appliquent aux cables de scanner ne
dépassant pas 3 métres (9.8 pieds) de long en extension maximale:
Folgendes trifft zu, wenn das Scannerkabel kürzer als 3 Meter ist:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
•
Consult the dealer or an experienced radio/TV technician for help
Notice
This Class B digital apparatus complies with Canadian ICES-003.
Remarque
Cet appareil numérique de classe B est conforme à la norme
canadienne NMB-003.
52
Patents
This Honeywell product may be covered by, but not limited to, one or more of the
following U.S. Patents:
U.S. Patent No.: 6,863,217; 6,948,659; 6,953,152; 6,962,289; 6,971,575;
6,971,577; 6,978,936; 7,044,383; 7,070,107; 7,086,594;
7,086,595; 7,128,266; 7,178,733; 7,185,817; 7,188,770;
7,213,762; 7,216,810; 7,225,988; 7,225,989; 7,237,722;
7,240,844; 7,243,847; 7,255,279; 7,267,282; 7,270,272;
7,273,180; 7,278,575; 7,281,661; 7,284,705; 7,293,714;
7,299,986; 7,320,431; 7,325,738; 7,347,374; 7,357,325;
7,360,706; 7,383,997; 7,407,109; 7,428,998; 7,464,877;
7,469,835; 7,472,831; 7,484,666; 7,487,917; 7,490,774;
7,490,778; 7,494,063; 7,503,498; 7,503,499; 7,510,122;
7,513,430; 7,527,206
No license, right or sublicense is granted, either expressly or by implication,
estoppel, or otherwise, under any Metrologic, Honeywell or third party intellectual
property rights (whether or not such third party rights are licensed to Metrologic
and/or Honeywell), including any third party patent listed above, except for an
implied license only for the normal intended use of the specific equipment,
circuits, and devices represented by or contained in the products that are
physically transferred to the user, and only to the extent of those license rights
and subject to any conditions, covenants and restrictions therein.
Other worldwide patents pending.
53
54
Index
A
F
AC ................................. 2, 7–11, 30
Accessories ...................................2
Adapter........................ 2, 13, 14, 45
Aperture.........................................4
Audible Indicator.............. 20–21, 34
Automatic Activation Mode ..........17
Field of View ............................... 22
Firmware ..................................... 34
Flash ROM.................................. 34
B
I
Bar Code ............. 23, 25–28, 29, 33
Beep .............. 20–21, 25–28, 29, 34
Blue LED ........... 4, 7–11, 20–21, 34
Button .................... 4, 17, 18, 20, 33
Immunity ............................... 50, 52
Indicator
Audible .............. 4, 20–21, 29, 34
Failure ........................... 4, 20–21
Visual ................ 4, 20–21, 29, 34
Interface .......................... 25–28, 29
Cable ....................... 7–11, 44–45
Keyboard Wedge... 1, 3, 8, 31, 43
RS232 ................... 1, 3, 7, 31, 43
RS485 ....................... 3, 9, 31, 43
USB ................... 3, 10, 11, 31, 43
IR .......................................... 17, 24
C
Cable .............................................6
Keyboard Wedge ....... 3, 8, 44–45
RS232........................ 3, 7, 44–45
RS485........................ 3, 9, 44–45
Termination................................4
USB ................... 3, 10, 11, 44–45
VLink.. 2, 3, 7–11, 25–28, 34, 44–
45
Caution ..............................7–11, 49
CE ....................................... 5, 7–11
Code Type................. 17, 18, 23, 30
Compliance ........... 7–11, 48, 49–52
Configuration ....... 25–28, 31, 33, 34
Connector Pinouts .......................43
Current ........................................30
Customer Service.......... 2, 3, 48, 57
D
DC ......................... 2, 30, 43, 44–45
Decode ........................................29
Default Parameters .....................31
Depth of Field ..............................23
E
EAS .......................................39, 40
EMC ................................ 30, 50, 52
EMI ..............................................50
Emissions ..............................50, 52
H
Host ........................................ 7–11
K
Keyboard Country Type .............. 31
Keyboard Type............................ 31
L
Labels ........................................... 5
LED....................... 7–11, 25–28, 29
Blue ......................... 7–11, 20–21
White ....................... 7–11, 20–21
License ................................. 17, 18
Light Levels................................. 30
Light Source................................ 29
M
Maintenance ................................. 5
Manual Activation Mode........ 17, 18
Manuals ........................................ 2
MetroSelect................................. 33
MetroSet2 ................................... 34
55
P
T
Pass-Through..............................17
Patent ..........................................53
Pinouts ............................ 43, 44–45
Power .......................... 7–11, 30, 34
Power Supply ...................... 6, 7–11
Presentation ................................17
Protocols .....................................31
Tone...................................... 20–21
Transformer .................. 2, 7–11, 30
Troubleshooting .................... 25–28
R
V
Razz .......................... 20–21, 25–28
Repair..........................................48
RMA ............................................48
Ventilation ................................... 30
Visual Indicator ............... 20–21, 34
Voltage........................................ 30
S
W
Safety ..........................................49
SELV .......................................7–11
Service ........................................48
Specifications
Electrical ..................................30
Environmental..........................30
Mechanical...............................30
Operational ..............................29
Swiftdecoder™ ..............................1
Wall Mount ............................ 13–16
Warranty ..................................... 48
White LED......... 4, 7–11, 20–21, 34
Window ..................................... 4, 5
56
U
UL ....................................... 5, 7–11
Upgrade ...................................... 34
Contact Information
The Americas
USA
Tel: 800.436.3876
(Customer Service)
866.460.8033
(Customer Support)
888.633.3762
(Technical Support)
Fax: 856.228.6673
(Sales)
856.228.1879
(Marketing)
856.228.0653
(Legal/Finance)
Brazil
Tel: 55.11.5185.8222
Fax: 55.11.5185.8225
Email:
[email protected]
Mexico
Tel: 55.5365.6247
Fax: 55.5362.2544
Email:
[email protected]
North America
Tel: 856.537.6400
866.460.8033
(Customer Service)
888.633.3762
(Technical Support)
Fax: 856.537.6474
Email:
[email protected]
South America
(Outside Brazil)
Tel: 55.11.5182.7273
Fax: 55.11.5182.7198
Email:
[email protected]
Omniplanar, Inc.
Tel: 856.374.5550
Fax: 856.374.5576
Email:
[email protected]
Spain
Tel: +34 913 272 400
Fax: +34 913 273 829
Email:
[email protected]
NOVODisplay
Tel: 856.537.6139
Fax: 856.537.6116
Email:
[email protected]
United Kingdom
Tel: +44 (0) 1256 365900
Fax: +44 (0) 1256 365955
Email:
[email protected]
Europe, Middle East,
and Africa
France
Tel: +33 (0) 1 48.63.78.78
Fax: +33 (0) 1 48.63.24.94
Email:
[email protected]
Asia Pacific
Australia
Tel: 1 800 99 88 38
Fax: +61 2 8916-6471
Email:
[email protected]
Germany
Tel: 49-89-89019-0
Fax: 49-89-89019-200
Email:
[email protected]
China
Tel: 86-21-58356616
86-21-58358830
Fax: 86-21-58358873
Email:
[email protected]
Italy
Tel: +39 0 51 6511978
Fax: +39 0 51 6521337
Email:
[email protected]
Suzhou Sales Office
Tel: 86-512-67622550
Fax: 86-512-67622560
Email:
[email protected]
Poland
Tel: +48 (22) 545 04 30
Fax: +48 (22) 545 04 31
Email:
[email protected]
Guangzhou Sales Office
Tel: 86-20-38823476
Fax: 86-20-38823477
Email:
[email protected]
Russia
Tel: +7 (495) 737 7273
Fax: +7 (495) 737 7271
Email:
[email protected]
Beijing Sales Office
Tel: 010-82253472/84583280
Fax: 010-82253648/84583102
Email:
[email protected]
57
Chengdu Sales Office
Tel: 028-66135066/86786348
Fax: 028-86787061
Email:
[email protected]
Japan
Tel: 81-3-3839-8511
Fax: 81-3-3839-8519
Email:
[email protected]
Singapore
Tel: (65) 6842-7155
Fax: (65) 6842-7166
Email:
[email protected]
Hong Kong
Tel: 852-2331-9133
Fax: 852-2511-3557
Korea
Korea Sales Office
Tel: (82) 2-6205-5379
Fax: (82)-2-3444-3980
Email:
[email protected]
Thailand
Tel: +662-610-3787
Fax: +662-610-3601
Email:
[email protected]
India
India Sales Office
Tel: +91 80 4125 6718
Fax: +91 80 4125 6719
Email:
[email protected]
58
Product Service and Repair
North America
Tel: 800.436.3876
(Customer Service)
866.460.8033
(Customer Support)
888.633.3762
(Technical Support)
Fax: 856.228.6673
(Sales)
Email:
[email protected]
Suzhou Sales Office
Tel: 86-512-67622550
Fax: 86-512-67622560
Email:
[email protected]
European Repair Center
Tel: +34 913 751 249
Fax: +34 913 270 437
59
Honeywell Scanning and Mobility
90 Coles Road
Blackwood, NJ 08012-4683
00-02290 Rev C
June 2009