ENGLISH
LC-46D85UN
FRANÇAIS
LC-52D85UN
OPERATION MANUAL
MODE D'EMPLOI
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
ESPAÑOL
LC-46D85UN
LC-52D85UN
LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR ACL
TELEVISOR CON PANTALLA
DE CRISTAL LÍQUIDO
OPERATION MANUAL
MODE D'EMPLOI
MANUAL DE OPERACIÓN
SHARP CORPORATION
MANUAL DE OPERACIÓN
Printed in Mexico
Imprimé au Mexique
Impreso en México
TINS-E228WJZZ
09P06-MX-NM
LC-46_52D85UN_E_Hyo1-4.indd 1
IMPORTANT : Please read this operation manual before starting operating the equipment.
IMPORTANT : Veuillez lire ce mode d'emploi avant de commencer à utiliser l'appareil.
IMPORTANTE : Lea este manual de operación antes de comenzar a operar el equipo.
2009/04/10 15:45:29
Dimensional Drawings
Unit: inch (mm)
LC-46D85UN
43 53/64 (1113)
16 25/32 (426)
22 43/64
(575.6)
29 45/64 (754)
21 21/32 (550)
4 47/64
(120)
15 3/4 (400)
3 29/32
(99)
15 3/4 (400)
6 3/4
(174.3)
1 63/64
(50)
27 47/64 (704)
40 19/64 (1023.4)
12 61/64
(329)
LC-52D85UN
49 19/64 (1252)
18 43/64 (474)
25 41/64
(651)
31 11/32 (796)
15 3/4 (400)
21 21/32 (550)
4 27/32
(123)
3 25/32
(96)
15 3/4 (400)
5 23/32
(145)
2 1/16
(52)
33 25/64 (848)
45 9/16 (1157)
12 61/64
(329)
LC-46_52D85UN_E_Hyo1-4.indd 2
2009/04/17 15:57:38
ENGLISH
LC-46D85UN
LC-52D85UN
LIQUID CRYSTAL TELEVISION
ENGLISH
OPERATION MANUAL
IMPORTANT:
To aid reporting in case of loss or theft, please record the
TV's model and serial numbers in the space provided. The
numbers are located at the rear of the TV.
Model No.:
Serial No.:
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION:
The lightning flash with arrow-head
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within a
triangle is intended to alert the user
to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the product.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
1
LC-46_52D85UN_E_01.indd 1
2009/04/10 15:41:48
IMPORTANT INFORMATION
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly
approved by the manufacturer could void the user's authority to operate this equipment.
CAUTION:
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded
cables and connectors for connections.
DECLARATION OF CONFORMITY:
SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-46D85UN/LC-52D85UN
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RESPONSIBLE PARTY:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
TEL: 1-800-BE-SHARP
For Business Customers: URL http://www.sharpusa.com
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
“Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National
Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as practical.”
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of
mercury. Disposal of these materials may be regulated due to environmental
considerations. For disposal or recycling information, please contact your local
authorities, the Electronic Industries Alliance: www.eiae.org, the lamp recycling
organization: www.lamprecycle.org or Sharp at 1-800-BE-SHARP
(For U.S.A. only)
Trademarks
• Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
• “HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.”
• Products that have earned the ENERGY STAR® are designed to protect the environment through superior energy
efficiency.
•
and LC logo mark are registered trademarks of SHARP Corporation.
This product is embedded with LC Font technology, which was developed by SHARP Corporation for clearly
displaying easy-to-read characters on LCD screens. However, other fonts are used for some screen pages, too.
2
LC-46_52D85UN_E_01.indd 2
2009/04/10 15:41:49
DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years
of trouble-free operation of your product, please read the Important Safety Instructions carefully before
using this product.
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage
if improperly handled. This product has been engineered and manufactured with the highest priority on safety.
However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please
observe the following instructions when installing, operating and cleaning the product. To ensure your safety
and prolong the service life of your Liquid Crystal Television, please read the following precautions carefully
before using the product.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Additional Safety Information
15) Power Sources—This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery power, or other sources, refer to the
operating instructions.
16) Overloading—Do not overload wall outlets, extension cords, or integral convenience receptacles as this
can result in a risk of fire or electric shock.
17) Object and Liquid Entry—Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
18) Damage Requiring Service—Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an improper adjustment
of other controls may result in damage and will often require extensive work by a qualified technician
to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this indicates a need for service.
19) Replacement Parts—When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
20) Safety Check—Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
21) Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product
according to the method recommended by the manufacturer.
3
LC-52D85UN_E.indb 3
2009/03/19 17:29:39
IMPORTANT SAFETY INSTRUCTIONS
• Outdoor Antenna Grounding — If an outside antenna is
connected to the television equipment, be sure the antenna
system is grounded so as to provide some protection against
voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC — NATIONAL ELECTRICAL CODE
• Turn off the main power and unplug the AC cord from the wall outlet before handling.
• Use a soft cloth and gently wipe the surface of the display panel. Using a hard cloth may
scratch the panel surface.
• Use a soft damp cloth to gently wipe the panel when it is really dirty.
(It may scratch the panel surface when wiped strongly.)
• If the panel is dusty, use an anti-static brush, which is commercially available, to clean it.
• To protect the panel, do not use a dirty cloth, liquid cleaners or chemical cloth to clean it, such materials may damage
the panel surface.
• To clean the outer cabinet, use the same method. Do not use liquid or aerosol cleaners.
• Water and Moisture — Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool; and the like.
• Stand — Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base
can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart,
stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product
on a wall, be sure to follow the manufacturer's instructions. Use only the mounting hardware recommended by the
manufacturer.
• Selecting the location — Select a place with no direct sunlight and good ventilation.
• Ventilation — The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents
and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place
the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not
designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper
ventilation is provided or the manufacturer's instructions are followed.
• The Liquid Crystal panel used in this product is made of glass. Therefore, it can break when the product is dropped or
applied with impact. Be careful not to be injured by broken glass pieces in case the panel breaks.
• Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
• The Liquid Crystal panel is a very high technology product with 2,073,600 pixels, giving you fine picture details.
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that
this does not affect the performance of your product.
• Lightning — For added protection for this television equipment during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to
the equipment due to lightning and power-line surges.
• Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
• To prevent fire, never place any type of candle or flames on the top or near the TV set.
• To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.
• Do not display a still picture for a long time, as this could cause an afterimage to remain.
• To prevent fire or shock hazard, do not expose this product to dripping or splashing.
No objects filled with liquids, such as vases, should be placed on the product.
• Do not insert foreign objects into the product. Inserting objects in the air vents or other openings may
result in fire or electric shock. Exercise special caution when using the product around children.
Precautions when transporting the TV
• When transporting the TV, never carry it by holding or otherwise putting pressure onto the display. Be sure to always
carry the TV by two people holding it with two hands — one hand on each side of the TV.
4
LC-52D85UN_E.indb 4
2009/03/19 17:29:40
IMPORTANT SAFETY INSTRUCTIONS
CHILD SAFETY:
It Makes A Difference How and Where You Use Your Flat Panel Display
Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind:
THE ISSUE
• The home theater entertainment experience is a growing trend and larger flat panel
displays are popular purchases. However, flat panel displays are not always supported
on the proper stands or installed according to the manufacturer’s recommendations.
• Flat panel displays that are inappropriately situated on dressers, bookcases, shelves,
desks, speakers, chests or carts may fall over and cause injury.
THIS MANUFACTURER CARES!
• The consumer electronics industry is committed to making home entertainment enjoyable
and safe.
TUNE INTO SAFETY
• One size does NOT fit all. Follow the manufacturer’s recommendations for the safe
installation and use of your flat panel display.
• Carefully read and understand all enclosed instructions for proper use of this product.
• Don’t allow children to climb on or play with furniture and television sets.
• Don’t place flat panel displays on furniture that can easily be used as steps, such as
a chest of drawers.
• Remember that children can become excited while watching a program, especially
on a “larger than life” flat panel display. Care should be taken to place or install the
display where it cannot be pushed, pulled over, or knocked down.
• Care should be taken to route all cords and cables connected to the flat panel
display so that they cannot be pulled or grabbed by curious children.
WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT YOUR FLAT
PANEL DISPLAY, ALWAYS:
• Use a mount that has been recommended by the display manufacturer and/or listed
by an independent laboratory (such as UL, CSA, ETL).
• Follow all instructions supplied by the display and wall mount manufacturers.
• If you have any doubts about your ability to safely install your flat panel display,
contact your retailer about professional installation.
• Make sure that the wall where you are mounting the display is appropriate. Some
wall mounts are not designed to be mounted to walls with steel studs or old cinder
block construction. If you are unsure, contact a professional installer.
• A minimum of two people are required for installation. Flat panel displays can be
heavy.
Note: CEA is the preeminent trade association promoting growth in the $161 billion U.S.
consumer electronics industry. More than 2,200 companies enjoy the benefits of CEA
membership, including legislative advocacy, market research, technical training and education,
industry promotion and the fostering of business and strategic relationships.
5
LC-52D85UN_E.indb 5
2009/03/19 17:29:40
Supplied Accessories
Make sure the following accessories are provided with the product.
Remote control unit
(g1)
Page 7
“AAA” size battery
(g2)
Page 8
AC cord
(g1)
Page 7
Cable clamp
(g1)
Page 7
Stand unit
(g1)
Page 6
Operation manual
(g1)
• Always use the AC cord supplied with the TV.
• To avoid scratching the frame or screen, please use a soft, lint free cloth for cleaning. Approved cleaning cloths are available
directly from Sharp in single (00Z-LCD-CLOTH) or triple (00Z-LCD-CLOTH-3) packs. Call 1-800-BE-SHARP for ordering, or
VISIT www.sharpusa.com/SharpDirect.
QUICK REFERENCE
Attaching the Stand
• Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged.
CAUTION
• Attach the stand in the correct direction.
• Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
1 Confirm that there are 8 screws (4 short screws
and 4 long screws) and a hex key supplied with the
stand unit.
3 1 Insert the stand into the openings on the bottom
of the TV.
2 Insert and tighten the 4 short screws into the 4
holes on the rear of the TV.
Hex key
2 Attach the supporting post for the stand unit onto
the base using the box for the stand unit as shown
below.
2
Short screws
2
Soft cushion
• The supporting post attaches to the base at an off-centered
location on the base. Be sure to attach the supporting post in
the direction indicated below and attach the stand to the TV
with the wider side of the base facing forward.
Long screws
Hex key
1
1
• To detach the stand, perform the steps in reverse order.
Forward
6
LC-52D85UN_E.indb 6
2009/03/19 17:29:40
QUICK REFERENCE
QUICK INSTALLATION TIPS
Using the Remote Control Unit
1
Attach your antenna to the back of the television.
(See page 8.)
2
Connect the AC plug for the television into the AC
outlet.
Use the remote control unit by pointing it towards the
remote control sensor on the TV. Objects between the
remote control unit and the remote control sensor may
prevent proper operation.
Remote control sensor
30º
17´ (5 m)
30º
30º
30º
AC outlet
• Place the TV close to the AC outlet, and keep the power
plug within reach.
■ Cautions regarding the remote control unit
• TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
TOUCH UN-INSULATED PARTS OF ANY CABLES
WITH THE AC CORD CONNECTED.
3
Place the Ferrite core in the space indicated in the
below figure and bundle the cords properly with
the cable clamp.
4
How to turn on the television for the first time.
A) Press POWER on the television.
• Do not expose the remote control unit to shock. In addition,
do not expose the remote control unit to liquids, and do not
place in an area with high humidity.
• Do not install or place the remote control unit under direct
sunlight. The heat may cause deformation of the remote
control unit.
• The remote control unit may not work properly if the remote
control sensor on the TV is under direct sunlight or strong
lighting. In such cases, change the angle of the lighting
or the TV, or operate the remote control unit closer to the
remote control sensor.
Ferrite core
POWER
B) The POWER indicator on the front of the
television lights GREEN.
IMPORTANT:
The POWER indicator on the television should light GREEN
indicating you have power to the television.
If the POWER indicator on the television still does not light up,
press TV POWER on the remote control to turn the power on.
IMPORTANT:
IF THE UNIT DOES NOT POWER ON - UNPLUG THE
TELEVISION FROM THE OUTLET AND REPEAT THE
INSTALLATION STEPS.
IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT
US AT 1-800-BE-SHARP.
POWER indicator
• Speakers cannot be detached from the TV.
• TV angle cannot be adjusted.
7
LC-52D85UN_E.indb 7
2009/03/19 17:29:41
Preparation
Antennas
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections
that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector,
plug it into the antenna terminal at the rear of the TV set.
1. A 75-ohm system is generally a round cable with F-type connector
that can easily be attached to a terminal without tools (Commercially
available).
2. A 300-ohm system is a flat “twin-lead” cable that can be attached
to a 75-ohm terminal through a 300/75-ohm adapter (Commercially
available).
F-type connector
75-ohm coaxial cable (round)
300-ohm twin-lead cable (flat)
NOTICE F-type connector should be finger-tightened only.
When connecting the RF cable to the TV set, do not tighten F-type
connector with tools.
If tools are used, it may cause damage to your TV set. (The breaking
of internal circuit, etc.)
F-type connector
75-ohm coaxial cable
Connecting Antenna Cable
• Connect the antenna cable to the TV using one of the methods in the illustration as shown (1, 2, 3 or 4).
1 Cable without a CATV
converter
Home Antenna
terminal (75-ohm)
Cable TV lead-In
Coaxial cable
(commercially available)
2 VHF/UHF antenna
Home Antenna
terminal (75-ohm)
75-ohm coaxial cable (round)
3 Combination VHF/
UHF antenna
Coaxial cable
(commercially available)
75-ohm coaxial cable (round)
or
300-ohm twin-lead cable (flat)
4 Separate VHF/UHF
antenna
VHF
UHF
ANTENNA ANTENNA
300/75-ohm adapter
(commercially available)
300-ohm
twin-lead cable
IN
300-ohm twin-lead cable
or
OUT
Combiner
(commercially available)
75-ohm coaxial cable
To TV antenna
terminal
Installing Batteries in the Remote Control Unit
If the remote control fails to operate TV functions, replace the batteries in the remote control unit.
1 Open the battery cover.
2 Insert two “AAA” size batteries
3 Close the battery cover.
(supplied with the product).
• Place the batteries with their terminals
corresponding to the (e) and (f)
indications in the battery compartment.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage
in old batteries.
• Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with skin can cause a
rash. If you find any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove batteries from it.
8
LC-52D85UN_E.indb 8
2009/03/19 17:29:42
Contents
IMPORTANT INFORMATION ..................................1
Trademarks ..............................................................2
DEAR SHARP CUSTOMER .....................................3
IMPORTANT SAFETY INSTRUCTIONS ..................3
Supplied Accessories..............................................6
QUICK REFERENCE ................................................6
Attaching the Stand .............................................6
QUICK INSTALLATION TIPS................................7
Using the Remote Control Unit ............................7
Preparation ..............................................................8
Antennas .............................................................8
Installing Batteries in the Remote Control Unit ......8
Contents ...................................................................9
Part Names ............................................................10
TV (Front) ...........................................................10
TV (Rear/Side)....................................................10
Remote Control Unit ..........................................11
Connecting to External Equipment ......................12
Connecting Audiovisual Equipment ....................12
Using Digital Audio Output .................................13
Connecting HDMI Equipment ............................13
Connecting a PC ...............................................13
Watching TV ...........................................................14
Turning On/Off the Power ..................................14
Initial Setup ........................................................14
Direct Button Operation........................................15
Changing Channels ......................................15
Changing Volume .........................................15
MUTE ...........................................................15
Sleep Timer ..................................................15
FLASHBACK ................................................15
SURROUND .................................................15
FREEZE .......................................................15
INPUT ..........................................................15
AV MODE .....................................................16
AUDIO ..........................................................16
POWER SAVING ...........................................17
Closed Captions and Digital Closed Captions ...17
VIEW MODE .................................................18
On-Screen Display Menu ......................................19
Menu Items .......................................................19
On-Screen Display Menu Operation ...................20
Menu Operation Buttons....................................20
Picture Menu .....................................................21
OPC Setting ..................................................21
Advanced Picture Setting ..............................21
Audio Menu .......................................................22
Surround .......................................................22
Bass Enhancer ..............................................22
Power Control Menu ..........................................23
Power Saving ................................................23
No Signal Off .................................................23
No Operation Off ...........................................23
Setup Menu .......................................................23
EZ Setup .......................................................23
CH Setup ......................................................24
Antenna Setup-DIGITAL ................................24
Input Skip......................................................24
Input Label ....................................................24
Auto Sync. (for Analog PC Input Mode Only)...24
Fine Sync. ....................................................24
Position .........................................................25
Language ......................................................25
Reset ............................................................25
Parental CTRL (Parental Control Setting) .......25
Option Menu......................................................28
Audio Only ....................................................28
Color System ................................................28
Input Select ...................................................28
HDMI Setup ..................................................28
PC Audio Select ............................................28
Output Select ................................................29
Caption Setup ...............................................29
Digital Caption Info.
(Digital Caption Information) ........................29
Program Title Display ....................................29
Game Play Time ............................................29
Operation Lock Out .......................................29
Favorite CH (Favorite Channel Setting) ..........29
Demo Mode ..................................................29
Digital Setup Menu ............................................30
Audio Setup ..................................................30
Identification ..................................................30
Software Update ...........................................30
Other Viewing Options ..........................................32
Presetting Remote Control Function ..................32
Operating the Connected Equipment .................32
Using AQUOS LINK ...............................................34
Controlling HDMI Equipment Using AQUOS LINK ...34
AQUOS LINK Setup .....................................35
One Touch Recording ..................................35
One Touch Playback ....................................36
AQUOS LINK Menu ...........................................36
Timer Recording ...........................................36
Playback of Titles Using AQUOS LINK ..........37
Selecting Media Type for
AQUOS LINK-Compatible Recorder ...........37
Listening with the AQUOS AUDIO
Speaker System ........................................37
Manually Changing AQUOS AUDIO
Speaker System's Sound Mode .................37
Displaying the Setup Menu of
AQUOS LINK-Compatible Equipment ........37
HDMI Device Selection .................................37
Appendix ................................................................38
Removing the Stand ..........................................38
Setting the TV on the Wall..................................38
Troubleshooting .................................................39
Troubleshooting-Digital Broadcasting ................39
RS-232C Port Specifications .............................40
Specifications ....................................................41
Optional Accessory ............................................41
PC Compatibility Chart ......................................42
Information on the Software License for This
Product ...........................................................42
Calling for Service .................................................43
LIMITED WARRANTY ............................................43
Dimensional Drawings
• The dimensional drawings for the LCD TV set are shown
on the inside back cover.
9
LC-52D85UN_E.indb 9
2009/03/19 17:29:42
Part Names
TV (Front)
Remote control sensor
OPC sensor* (See page 21.)
POWER indicator (See page 14.)
OPC indicator (See page 21)
* OPC: Optical Picture Control
TV (Rear/Side)
*2
*3
POWER
button
MENU
button
AC INPUT
terminal
INPUT
button
*1
INPUT 7 terminal
(HDMI)
Channel
buttons
(CHU/V)
INPUT 9 terminal
(HDMI)
INPUT 8 terminal
(HDMI)
Volume
buttons
(VOLk/l)
DIGITAL AUDIO
OUTPUT terminal
AUDIO OUTPUT
terminals
*1
INPUT 5
terminal
(HDMI)
Antenna/Cable in
INPUT 1 terminals
INPUT 3
terminals
INPUT 2 terminals
RS-232C terminal
INPUT 4 terminal (PC-IN)
SERVICE
terminal
AUDIO terminal (shared for INPUT 4 and INPUT 6) *4
INPUT 6 terminal (HDMI)
*1 See pages 12 and 13 for external equipment connection.
*2 See page 20 for button operations.
*3 See page 7 for connecting the AC cord.
*4 See page 28 for details on the PC Audio Select function.
• The illustrations in this operation manual are for explanation purposes and may vary slightly from the actual operations.
• The examples used throughout this manual are based on the LC-52D85UN model.
10
LC-46_52D85UN_E_01.indd 10
2009/04/10 15:42:00
Part Names
Remote Control Unit
1
2
3
17
18
4
19
1
TV POWER: Switch the TV power on or enter standby. (See page
14.)
2
DISPLAY: Display the channel information.
3
SOURCE POWER: Turns the power of the external equipment
on and off.
4
External equipment operational buttons: Operate the external
equipment.
5
0–9: Set the channel. (See page 15.)
6
• (DOT): (See pages 15 and 32.)
7
INPUT: Select a TV input source. (TV, INPUT 1, INPUT 2, INPUT
3, INPUT 4, INPUT 5, INPUT 6, INPUT 7, INPUT 8, INPUT 9) (See
page 15.)
8
VOLk/l: Set the volume. (See page 15.)
9
POWER SAVING: Select Power Saving settings. (See page 17.)
10 FREEZE: Set the still image. Press again to return to normal
screen. (See page 15.)
11 EXIT: Turn off the menu screen.
5
6
20
7
21
8
22
9
23
10
24
25
11
12
13
14
26
27
28
29
30
15
16
12 OPTION: Display the AQUOS LINK MENU screen. This button
will function only when AQUOS LINK is used. (See pages 34 to 37
for details.)
13 REC STOP: Stops one touch recording. This button will function
only when AQUOS LINK is used. (See pages 34 to 37 for details.)
14 SLEEP: Set the sleep timer. (See page 15.)
15 SURROUND: Select Surround settings. (See page 15.)
16 AUDIO: Selects the MTS/SAP or the audio mode during multichannel audio broadcasts. (See page 16.)
17 FUNCTION: Switches the remote control for TV, CBL/SAT, VCR,
DVD and AUDIO operation. Indicator lights up for the current
mode. (See pages 32 to 33 for details.)
* To enter the code registration mode, you need to press
FUNCTION and DISPLAY at the same time.
18 LIGHT D: When this button is pressed, some buttons (for
example, VOLk/l and CHr/s) on the remote control unit will
light. The lighting will turn off if no operations are performed within
about 5 seconds. This button is used for performing operations in
low-light situations.
19 VIEW MODE: Select the screen size. (See page 18.)
20 ENT: Jumps to a channel after selecting with the 0–9 buttons.
21 FLASHBACK: Return to the previous channel or external input
mode. (See page 15.)
22 CHr/s: Select the channel. (See page 15.)
23 MUTE: Mute the sound. (See page 15.)
24 MENU: Display the menu screen.
25 a/b/c/d, ENTER: Select a desired item on the screen.
26 RETURN: Return to the previous menu screen.
27 FAVORITE CH
A, B, C, D: Select 4 preset favorite channels in 4 different
categories. (See page 29.)
While watching, you can toggle the selected channels by pressing
A, B, C and D.
28 FAVORITE: Set the favorite channels. (See page 29.)
29 CC: Display captions from a closed-caption source. (See page 17.)
30 AV MODE: Select an audio or video setting.
(When the input source is TV, INPUT 1, 2 or 3: STANDARD,
MOVIE, GAME, USER, DYNAMIC (Fixed), DYNAMIC. When the
input source is INPUT 4, 5, 6, 7, 8 or 9: STANDARD, MOVIE,
GAME, PC, USER, DYNAMIC (Fixed), DYNAMIC) (See page 16.)
• When using the remote control unit, point it at the TV.
11
LC-52D85UN_E.indb 11
2009/03/19 17:29:43
Connecting to External Equipment
You can connect many types of external equipment to your TV like a Blu-ray disc player, DVD player, VCR, Digital
TV tuner, HDMI equipment, game console or camcorder. To view external source images, select the input source
from INPUT on the remote control unit or on the TV. (See page 15.)
CAUTION
• To protect equipment, always turn off the TV before connecting any external equipment.
• Please read the relevant operation manual (Blu-ray disc player, etc.) carefully before making connections.
Connecting Audiovisual Equipment
You can use the INPUT 1, INPUT 2 or INPUT 3 terminals when connecting to a Blu-ray disc player, DVD player, a
Digital TV STB (Air or Cable), VCR, game console, and camcorder.
When using composite cable (INPUT 1 or 3):
Blu-ray disc player/
DVD player/Digital TV STB/VCR/
Game console/Camcorder
AV cable
(commercially available)
VIDEO (Yellow)
AUDIO-L (White)
AUDIO-R (Red)
When using component cable (INPUT 1 or 2):
Blu-ray disc player/
DVD player/Digital TV STB
Component video cable
(commercially available)
Audio cable
(commercially available)
AUDIO-L (White)
AUDIO-R (Red)
Y (Green)
PB (Blue)
PR (Red)
When using S-VIDEO cable (INPUT 2):
VCR/Game console/
Camcorder
S-VIDEO cable
(commercially available)
Audio cable
(commercially available)
AUDIO-L (White)
AUDIO-R (Red)
• To enjoy the AQUOS 1080p display capability, connect your external equipment using a component cable and set the
equipment to 1080p output.
• See page 13 for connecting a Blu-ray disc player, DVD player or a Digital TV STB to the HDMI terminal.
• The COMPONENT terminals take priority over the VIDEO (INPUT 1) and S-VIDEO (INPUT 2) terminals.
12
LC-52D85UN_E_01.indd 12
2009/04/06 16:34:40
Connecting to External Equipment
Using Digital Audio Output
It is possible to output audio through the DIGITAL AUDIO OUTPUT terminal. (See page 30 for details.) PCM audio
outputs from the terminal.
To optical digital input of
external audio devices
Optical fiber cable
(commercially available)
• Depending on the connected equipment, audio will not output from the DIGITAL AUDIO OUTPUT terminal in HDMI
connection. In this case, set the audio formats of the connected equipment to PCM, 32/44.1/48 kHz.
Connecting HDMI Equipment
You can use the INPUT 5, INPUT 6, INPUT 7, INPUT 8 or INPUT 9 terminal when connecting HDMI equipment.
HDMI-certified cable
(commercially available)
HDMI equipment
• When using an HDMI-DVI conversion cable, input the audio signal to the AUDIO terminal of INPUT 6.
When you input the audio signal via the AUDIO terminal with INPUT 6, set "PC Audio Select" to "Input 6 (HDMI)". (See page 28.)
• To enjoy the AQUOS 1080p display capability, connect your Blu-ray disc player or other external equipment using an HDMIcertified cable and set the equipment to 1080p output.
Connecting a PC
When connecting to a PC with an analog RGB terminal (INPUT 4):
Ø 3.5 mm stereo minijack cable
(commercially available)
RGB cable
(commercially available)
PC
When connecting to a PC with an HDMI terminal (INPUT 5, 6, 7, 8 or 9):
PC
•
•
•
•
HDMI-certified cable
(commercially available)
When connecting a PC to the INPUT 4, set "PC Audio Select" to "Input 4 (PC)". (See page 28.)
When connecting a PC to the INPUT 6, set "PC Audio Select" to "Input 6 (HDMI)". (See page 28.)
The HDMI terminals only support digital signal.
Refer to page 42 for a list of PC signals compatible with the TV.
13
LC-52D85UN_E.indb 13
2009/03/19 17:29:44
Watching TV
Turning On/Off the Power
Press POWER on the TV, or TV POWER on the remote control unit to
turn the power on.
POWER
• POWER indicator (Green): The TV is on. (After a few seconds, a window
appears with sound.)
• The initial setup starts when the TV powers on for the first time. If the TV has
been turned on before, the initial setup will not be invoked. For changing the
settings of the initial setup, perform EZ setup on the Setup menu on page 23.
Press POWER on the TV, or TV POWER on the remote control unit
again to turn the power off.
TV POWER
(On/Standby)
• The TV enters standby and the image on the screen disappears.
• The POWER indicator on the TV turns off.
• If you are not going to use this TV for a long period of time, be sure to remove
the AC cord from the AC outlet.
• Weak electric power is still consumed even when the TV is turned off.
Initial Setup
When you turn on the TV for the first time, it will
automatically memorize the broadcasting channels
available in the region where you live. Perform the
following steps before you press TV POWER on the
remote control unit.
1. Insert the batteries into the remote control unit. (See page 8.)
2. Connect the antenna cable to the TV. (See page 8.)
3. Plug in the AC cord to the AC outlet. (See page 7.)
• ENERGY STAR qualification is based on AV MODE "STANDARD".
Air/Cable (Antenna setting)
Make sure what kind of connection is made with your TV
when selecting "Air" or "Cable".
3
Press c/d to select "Air" or "Cable".
Press ENTER to enter the setting.
Cable
Air
Language (Language setting)
Select from among 3 languages: English, French and Spanish.
1
Press a/b to select the desired language listed on the
screen, and then press ENTER.
Language
CH Search (Channel search)
Channel auto search makes the TV look for all channels
viewable in the set area.
4
When "Air" is selected in Antenna setting:
Press c/d to select "Start", and then press ENTER.
English
TV Location
Français
Air/Cable
TV Location
Select "Home" or "Store" for the location where you plan to
install the TV. This product qualifies for ENERGY STAR V3.0
in Home mode default setting.
2
Cancel
Start
Español
CH Search
Press c/d to select "Home" or "Store".
Press ENTER to enter the setting.
When "Cable" is selected in Antenna setting:
Press a/b to select "Analog & Digital Search Start" to
search both analog and digital broadcasts, or to select
“Analog Search Start” to search only analog broadcasts,
and then press ENTER.
Analog & Digital Search Start
Home
Store
Analog Search Start
Cancel
Home: “Power Saving” is set to "Advanced", and AV
MODE is set to "STANDARD".
Store: “Power Saving” is set to "Off" and AV MODE is set to
"DYNAMIC (Fixed)". Picture Reset and Feature Demo can
be set.
Picture Reset: AV MODE will be set to "DYNAMIC (Fixed)"
regardless of whether Picture Reset is "On" or "Off". If you
select "On", AV MODE will be reset to "DYNAMIC (Fixed)" if
there is no operation for 30 minutes. When "Off" is selected,
AV MODE will be set to "DYNAMIC (Fixed)".
Feature Demo: When “On” is selected, after all the settings are
completed, the Feature Demo screen is displayed if there is
no operation for several minutes.
• The Channel search will start automatically.
• To exit the Channel search screen, select "Cancel", and
then press ENTER.
• If no channel is found, confirm the type of connection made
with your TV and try EZ Setup again.
(See page 23.)
• For changing the settings of the initial setup, perform EZ
setup on the Setup menu on page 23.
14
LC-52D85UN_E.indb 14
2009/03/19 17:29:45
Direct Button Operation
Sleep Timer
Allows you to set a time when the TV automatically
switches to standby.
Press SLEEP.
• The remaining time displays when the sleep timer has been set.
• Each time you press SLEEP, the remaining time switches
as shown below.
Off
30
60
90
120
• When set, the time automatically starts counting down.
• If you want to adjust the sleep timer, you can press SLEEP
twice then change the time setting.
• When it is 5 minutes before the time expires, the remaining
time will start to keep appearing every minute.
Changing Channels
You can change channels by pressing CHr/s or 0-9,
• (DOT).
Examples:
To select a 1 or 2-digit channel number (e. g., Channel 5):
Press 5
ENT.
To select a 3-digit channel number (e. g., Channel 115):
Press 1
1
5
ENT.
To select a 4-digit channel number (e. g., Channel 22.1):
Press 2
2
• (DOT)
1
ENT.
• When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
• When you enter 0-9 only, channel selection will be made if
there is no operation within a few seconds.
• If you push "0" by itself, nothing will happen.
• Complete the above steps within a few seconds.
• When you enter 0-9 and • (DOT), channel selection will be
made if there is no operation within a few seconds.
• Select "Off" by pressing SLEEP to cancel the sleep timer.
• The TV will enter standby when the remaining time reaches 0.
FLASHBACK
Press FLASHBACK to switch to the previously tuned
channel.
• Press FLASHBACK again to switch back to the currently
tuned channel.
• FLASHBACK will not work if no channel has been changed
after the TV is turned on.
SURROUND
The surround function produces Surround effect from
the speakers. Each time you press SURROUND, the
mode changes between On and Off.
On: Makes it possible to enjoy natural, realistic surround
sound.
Off: Outputs the normal sound.
Changing Volume
You can change the volume by pressing VOLk/l on
the TV or on the remote control unit.
• To increase the volume, press VOLk.
• To decrease the volume, press VOLl.
20
Audio status
Output device
Speaker
Output Select
Fixed
Variable
Variable sound
Mute
• When "Output Select" is set to "Variable", the indicator on
the screen changes as shown below.
60
• See page 29 for details on the Output Select function.
MUTE
Mutes the current sound output.
Press MUTE.
" will be displayed on the screen for 30 minutes, and
• "
the sound is silenced.
• Within 30 minutes of pressing MUTE, mute can be
canceled by pressing VOLk/l or MUTE.
• Mute will be canceled after 30 minutes have passed.
However, the TV will not suddenly output a loud sound as
the volume level is set to 0 automatically.
• You can have the same settings by choosing "Surround" on
the menu items. (See page 22.)
FREEZE
Allows you to capture and freeze a moving image that
you are watching.
Press FREEZE.
• A moving image is captured.
• Press FREEZE again to cancel the function.
• When this function is not available, "No displaying still
image available." will display.
• The still image automatically goes out after 30 minutes.
• If you are using the freeze function and a broadcast
activates the V-CHIP BLOCK, the freeze function will be
canceled and a V-CHIP BLOCK message will appear.
INPUT
To view external source images, select the input source
using INPUT on the remote control unit or on the TV.
1 Press INPUT.
• A list of selectable sources appears.
2 Press INPUT again or press a/b to select the
input source.
• An image from the selected source automatically displays.
• Each time INPUT is pressed, the input source toggles.
• If the corresponding input is not plugged in, you cannot change
the input. Be sure to connect the equipment beforehand.
• See pages 12 and 13 for external equipment connection.
15
LC-52D85UN_E.indb 15
2009/03/19 17:29:47
Direct Button Operation
AV MODE
AUDIO
AV MODE gives you several viewing options to choose
from to best match the surrounding environment of the
TV, which can vary due to factors like room brightness,
type of program watched or the type of image input
from external equipment.
Press AV MODE. Current AV MODE displays.
• Press AV MODE again before the mode displayed on the
screen disappears. The mode changes as shown below:
Example:
When the input source is TV, INPUT 1, 2 or 3 terminals
STANDARD
MOVIE
DYNAMIC
GAME
USER [TV]
DYNAMIC (Fixed)
Example:
When the input source is INPUT 4, 5, 6, 7, 8 or 9
terminals
STANDARD
MOVIE
GAME
DYNAMIC
DYNAMIC (Fixed)
PC
USER[
]
STANDARD: For a highly defined image in a normal
lighting.
MOVIE: For a movie.
GAME: Lowers image brightness for easier viewing.
PC: For PC.
USER: Allows the user to customize settings as desired.
You can set the mode for each input source.
DYNAMIC (Fixed): Changes the image and sound
settings to the factory preset values. No adjustments
are allowed.
DYNAMIC: For a clear-cut image emphasizing high
contrast, useful for sports viewing.
• You can select a different AV MODE item for each input
mode. (For example, select STANDARD for TV input and
DYNAMIC for INPUT 1.)
• When you play games, "GAME" is recommended for AV
MODE.
■ MTS/SAP stereo mode
The TV has a feature that allows reception of sound
other than the main audio for the program. This feature
is called Multi-channel Television Sound (MTS). The TV
with MTS can receive mono sound, stereo sound
and Secondary Audio Programs (SAP). The SAP
feature allows a TV station to broadcast other
information, which could be audio in another language
or something completely different like weather
information.
You can enjoy Hi-Fi stereo sound or SAP broadcasts
where available.
• Stereo broadcasts: View programs like live sporting
events, shows and concerts in dynamic stereo sound.
• SAP broadcasts: Receive TV broadcasts in either MAIN or
SAP sound.
MAIN sound: The normal program soundtrack (either in
mono or stereo).
SAP sound: Listen to a second language, supplementary
commentary or other information. (SAP is mono sound.)
If stereo sound is difficult to hear.
• Obtain a clearer sound by manually switching to fixed
mono-sound mode.
You can change MTS as shown below to match the television
broadcast signal.
Press AUDIO to toggle between audio modes.
Examples: when receiving MTS and SAP
MONO
STEREO mode: STEREO
STEREO + SAP mode: ST(SAP)
SAP(ST)
MAIN + SAP mode: MAIN
MONO mode: MONO
MONO
SAP
■ Digital broadcasting audio mode
The types of audio transmitted in a digital broadcast include
SURROUND as well as MONO and STEREO. In addition, it
is possible for multiple audio tracks to accompany a single
video track.
Press AUDIO to toggle between audio modes.
Example: when receiving Digital broadcasting
STEREO (Audio1)
STEREO (Audio2)
SURROUND (Audio3)
• MTS only operates while in TV mode.
16
LC-52D85UN_E.indb 16
2009/03/19 17:29:48
Direct Button Operation
POWER SAVING
Allows you to set the Power Saving level in order to
decrease the power consumption and increase the
backlight lifespan.
Press POWER SAVING.
• Each time you press POWER SAVING, the mode changes
as shown below.
Off
Standard
Advanced
1 Press CC.
• This will present the Closed Caption information
display.
2 Press CC while the Closed Caption information is
still on the screen.
• Press repeatedly until you select the desired closed
caption service.
Air
• You can have the same settings by choosing "Power
Saving" on the menu items. (See page 23.)
Closed Captions and Digital Closed Captions
Your TV is equipped with an internal Closed Caption
decoder. It allows you to view conversations, narration
and sound effects as subtitles on your TV. Closed
Captions are available on some TV programs and on
some VHS home video tapes at the discretion of the
program provider.
Digital Closed Caption service is a new caption service
available only on digital TV programs (also at the
discretion of the service provider). It is a more flexible
system than the original Closed Caption system,
because it allows for a variety of caption sizes and font
styles. When the Digital Closed Caption service is in
use, it will be indicated by the appearance of a 3-letter
abbreviation that also indicates the language of the
Digital Closed Captions: ENG (English), SPA (Spanish),
FRA (French) or other language codes.
Not all programs and VHS videotapes offer closed
captions. Please look for the “N” symbol to ensure
that captions will be shown.
In the Closed Caption system, there can be more than
one caption service provided. Each is identified by its
own number. The “CC1” and “CC2” services display
subtitles of TV programs superimposed over the
program's picture.
In the Closed Caption system, the “Text1” or “Text2”
services display text that is unrelated to the program
being viewed (e.g., weather or news). These services
are also superimposed over the program currently
being viewed.
DIGITAL
22.1
Audio
Video
CC
Ratings
:
:
:
:
MONO
1080i (16:9)
1/2 CC1
NONE
Closed Caption
information
• Depending on the number of caption services in the
signal being received, you will see information such as
1/2 or 1/4 displayed.
1/2 means “the first of two services”.
Example:
If a program has three services (Digital CC(ENG), CC1
and Text1), the closed caption display will toggle in this
sequence:
1/3 ENG
2/3 CC1
3/3 Text1
Off
• The CC button keeps a record of the last service
selected in its memory.
If the last closed caption mode (e.g. 1/3 ENG) you
selected is not available for the next program, or on
another channel, the closed caption service that is
available is automatically selected, and this service
appears in parentheses, e.g. “1/3(CC1)”.
Closed Caption services that appear in parentheses will
not be stored in the CC button's memory as your last
selected service. Only services that you have selected
with the CC button are stored.
Examples:
In a case where there are two closed caption
services provided (for instance, Digital CC(ENG)
and CC1), and Digital CC(ENG) is displayed
as your current selection, if Digital CC(ENG) is
not broadcast for the next program, the other
closed caption service, CC1, will be displayed in
parentheses.
A closed caption service appears in parentheses
because the service you selected is not available
and a different service is displayed on your screen.
“1/1(CC1)” is displayed instead of “1/2/ENG”.
• When “Power Saving” is set to “Standard” or “Advanced”,
the Power Saving leaf icon appears on the channel
information window. See page 23 for details of Power
Saving settings.
• See page 29 for detailed closed caption settings.
• When the program contains no closed caption, “--” displays
in the closed caption information.
• If the language code, e.g. “ENG”, is not found on Digital TV
programs, “--” will be shown.
• Four kinds of closed caption service (CC1, CC2, Text1,
Text2) are potentially available, but a broadcast may contain
none or only some of these services at the discretion of the
program provider.
17
LC-52D85UN_E.indb 17
2009/03/19 17:29:49
Direct Button Operation
VIEW MODE
You can select the screen size.
1 Press VIEW MODE.
• The View Mode menu displays.
• The menu lists the View Mode options selectable for the type of video signal currently being received.
2 Press VIEW MODE or a/b while the View Mode menu is displayed to select a desired item on the menu.
• You can sequentially select a View Mode that has its own aspect ratio.
■ For 4:3 programs
Example: Screen size images
Side Bar
Suitable for viewing
conventional 4:3 programs in
their normal format.
S.Stretch (Smart stretch)
Zoom
Suitable for stretching 4:3
programs to fill the screen.
Stretch
Suitable for viewing widescreen 2.35:1 anamorphic
DVDs in full screen.
This mode is useful for 1.78:1
DVDs. When viewing 1.85:1
DVDs, stretch mode will still show
very thin black bands at the top
and bottom of the screen.
■ For HD programs
Stretch: Suitable for viewing wide-screen 1.78:1 aspect ratio program, stretch mode will still show very thin black bands at
the top and bottom of the screen.
Dot by Dot (1080i/p only): Detects the resolution of the signal and displays an image with the same number of pixels on
the screen.
Full Screen (720p only): You can select "Full Screen" only when receiving a 720p signal.
S.Stretch (Smart stretch): Suitable for stretching 4:3 programs to fill the screen.
Zoom: Suitable for viewing wide-screen 2.35:1 aspect-ratio programs in full screen.
• When using Dot by Dot or Full Screen, it is possible to see noise or bars around different outer portions of the screen. Please
change view mode to correct this.
■ For PC input mode
• Connect the PC before making adjustments. (See page 13.)
• Selectable screen size may vary with input signal type.
Example: Screen size images
Input signal
4:3
Normal
Keeps the original
aspect ratio in a full
screen display.
Zoom
For viewing
widescreen
programs. The top
and bottom of the
image is cropped.
Input signal
Stretch
Dot by Dot
16:9
An image fully fills the
screen.
Detects the resolution
of the signal and
displays an image with
the same number of
pixels on the screen.
Stretch
Dot by Dot
An image fully fills the
screen.
Detects the resolution
of the signal and
displays an image with
the same number of
pixels on the screen.
18
LC-52D85UN_E.indb 18
2009/03/19 17:29:50
On-Screen Display Menu
Menu Items
For TV/INPUT 1/2/3 Mode
For HDMI/PC-IN Mode
Picture Menu
OPC ..................................................................................... Page 21
Backlight.............................................................................. Page 21
Contrast .............................................................................. Page 21
Brightness .......................................................................... Page 21
Color ................................................................................... Page 21
Tint ...................................................................................... Page 21
Sharpness .......................................................................... Page 21
Advanced
C.M.S.-Hue ............................................................. Page 21
C.M.S.-Saturation ................................................... Page 21
C.M.S.-Value ........................................................... Page 21
Color Temp. ............................................................ Page 21
Fine Motion Enhanced ............................................. Page 21
Active Contrast ....................................................... Page 21
Gamma Adjustment ................................................. Page 22
Film Mode ............................................................... Page 22
Digital Noise Reduction ......................................... Page 22
3D-Y/C .................................................................... Page 22
Monochrome ........................................................... Page 22
Range of OPC ......................................................... Page 22
Reset .................................................................................. Page 21
Picture Menu
OPC ..................................................................................... Page 21
Backlight.............................................................................. Page 21
Contrast .............................................................................. Page 21
Brightness .......................................................................... Page 21
Color ................................................................................... Page 21
Tint ...................................................................................... Page 21
Sharpness .......................................................................... Page 21
Advanced
C.M.S.-Hue ............................................................. Page 21
C.M.S.-Saturation ................................................... Page 21
C.M.S.-Value ........................................................... Page 21
Color Temp. ............................................................ Page 21
Fine Motion Enhanced ............................................. Page 21
Active Contrast ........................................................ Page 21
Gamma Adjustment ................................................. Page 22
Film Mode ............................................................... Page 22
Digital Noise Reduction ......................................... Page 22
Monochrome ........................................................... Page 22
Range of OPC ......................................................... Page 22
Reset .................................................................................. Page 21
Audio Menu
Treble ................................................................................. Page 22
Bass..................................................................................... Page 22
Balance................................................................................ Page 22
Surround.............................................................................. Page 22
Bass Enhancer .................................................................... Page 22
Reset .................................................................................. Page 22
Audio Menu
Treble ................................................................................. Page 22
Bass..................................................................................... Page 22
Balance................................................................................ Page 22
Surround.............................................................................. Page 22
Bass Enhancer .................................................................... Page 22
Reset .................................................................................. Page 22
Power Control Menu
Power Saving ...................................................................... Page 23
No Signal Off ....................................................................... Page 23
No Operation Off ................................................................. Page 23
Power Control Menu
Power Saving ...................................................................... Page 23
No Signal Off ....................................................................... Page 23
No Operation Off ................................................................. Page 23
Setup Menu
EZ Setup.............................................................................. Page 23
CH Setup ............................................................................. Page 24
Antenna Setup-DIGITAL ...................................................... Page 24
Input Skip ............................................................................ Page 24
Input Label .......................................................................... Page 24
Parental CTRL .............................................................. Pages 25-27
Position................................................................................ Page 25
Language............................................................................. Page 25
Reset ................................................................................... Page 25
Setup Menu
Input Skip ............................................................................ Page 24
Auto Sync. .......................................................................... Page 24
Input Label .......................................................................... Page 24
Fine Sync. ........................................................................... Page 24
Position................................................................................ Page 25
Language............................................................................. Page 25
Reset ................................................................................... Page 25
Option Menu
AQUOS LINK Setup ............................................................ Page 35
Audio Only ........................................................................... Page 28
Input Select ......................................................................... Page 28
PC Audio Select ................................................................ Page 28
Output Select ...................................................................... Page 29
Color System ....................................................................... Page 28
Caption Setup ..................................................................... Page 29
Digital Caption Info. . ........................................................... Page 29
Program Title Display ......................................................... Page 29
Favorite CH ......................................................................... Page 29
Game Play Time .................................................................. Page 29
Operation Lock Out ............................................................. Page 29
Demo Mode ....................................................................... Page 29
Option Menu
AQUOS LINK Setup ............................................................ Page 35
Audio Only ........................................................................... Page 28
HDMI Setup ......................................................................... Page 28
PC Audio Select ................................................................. Page 28
Output Select ...................................................................... Page 29
Game Play Time .................................................................. Page 29
Operation Lock Out ............................................................. Page 29
Demo Mode ....................................................................... Page 29
Digital Setup Menu
Audio Setup ......................................................................... Page 30
Identification ........................................................................ Page 30
Software Update .......................................................... Pages 30-31
Digital Setup Menu
Software Update .......................................................... Pages 30-31
• Some menu items may not be displayed depending on the selected input source.
19
LC-52D85UN_E.indb 19
2009/03/19 17:29:51
On-Screen Display Menu
On-Screen Display Menu Operation
LCFONT embedded
Example
Picture
Example
Option
AQUOS LINK Setup
OPC
Off
On
On : Display
Audio Only
Backlight
[b12] a16
b16
PC Audio Select
Contrast
[b30]
b40
Output select
0
[Input 4 (PC)]
[Fixed]
Brightness [
0] a30
b30
Caption Setup
Color
[
0] a30
b30
Digital Caption Info.
Tint
[
0] a30
b30
Program Title Display
b10
Favorite CH
Sharpness [ b2] a10
Operation Lock Out
Advanced
[No]
[Off]
Demo Mode
Reset
1 Item displayed in yellow
• This indicates the item currently selected.
• Press ENTER to go to the adjustment screen for this
item.
: Select
ENTER
: Enter
RETURN
: Back
MENU
: Exit
2 Item in brackets
• This indicates the current setting for the item.
3 Item displayed in white
The bar above is an operational guide for
the remote control. The bar will change in
accordance with each menu setting screen.
1 Press c/d to select the desired item.
2 Press a/b to select the desired item.
• This indicates that the item can be selected.
4 Item displayed in gray
• This indicates that the item cannot be selected.
There are various reasons why the items cannot be
selected, but the main reasons are as follows:
—Nothing is connected to the selected input terminal.
—The function is not compatible with the current input
signal.
3 Press c/d to adjust the item.
• Menu options differ in the selected input modes, but the operating procedures are the same.
• The screens in the operation manual are for explanation purposes (some are enlarged, others cropped) and may vary slightly
from the actual screens.
LCFONT:
• This product is embedded with LC Font technology, which was developed by SHARP Corporation for clearly displaying easyto-read characters on LCD screens.
Menu Operation Buttons
Using the remote control
Use the following buttons on the remote control to
operate the menu.
Using the control panel of the main unit
You can also operate the menu with the control panel
of the main unit.
Button operations on the control panel correspond to
the ones on the remote control as shown below.
MENU: MENU on the remote
control.
INPUT: ENTER on the remote
control.
MENU:
Press to open or close the menu screen.
a/b/c/d:
Press to select a desired item on the screen or
adjust a selected item.
Press to go to the next step or complete the
setting.
Press to return to the previous step.
ENTER:
RETURN:
CHr/s: Cursor a/b on the
remote control.
VOLk/l: Cursor c/d on the
remote control.
20
LC-52D85UN_E_03.indd 20
2009/03/30 15:06:58
On-Screen Display Menu
Picture Menu
Adjusts the picture to your preference with the
following picture settings.
Example
Picture
OPC
Off
On
On : Display
Backlight
[b12] a16
b16
Contrast
[b30]
0
b40
Brightness [
0] a30
b30
Color
[
0] a30
b30
Tint
[
0] a30
b30
Sharpness [ b2] a10
b10
Advanced
• When set to "On", the Optical Picture Control (OPC) senses
the surrounding light and automatically adjusts the backlight
brightness. Make sure nothing obstructs the OPC sensor,
which could affect its ability to sense surrounding light.
• When set to "On: Display", OPC effect displays on the
screen while the OPC adjusts the screen brightness.
• When set to "On" or "On: Display", the OPC indicator on
the TV lights green.
Advanced Picture Setting
This TV provides various advanced functions for
optimizing the picture quality.
C.M.S.
(Color Management System)
Color tone is managed using the six-color adjustment
setting.
C.M.S.-Hue: This is a standard to adjust the color either
more reddish or more bluish in tone.
C.M.S.-Saturation: Increases or decreases the
saturation of a selected color.
C.M.S.-Value: A higher value makes the image
Reset
brighter.
A lower value makes the image darker.
1 Press MENU to display the MENU screen, and then
press c/d to select "Picture".
2 Press a/b to select a specific adjustment item.
• Select "Advanced" and then press ENTER to set
"C.M.S.-Hue", "C.M.S.-Saturation", "C.M.S.-Value",
"Color Temp.", "Fine Motion Enhanced", "Active
Contrast", "Gamma Adjustment", "Film Mode", "Digital
Noise Reduction", "3D-Y/C", "Monochrome" or "Range
of OPC".
3 Press a/b(or c/d) to select the desired setting,
4
and then press ENTER.
Press MENU to exit.
Selected item
Backlight
cbutton
The screen dims
Contrast
Brightness
For less contrast
For less
brightness
For less color
intensity
Skin tones
become reddish
For less
sharpness
Color
Tint
Sharpness
dbutton
The screen
brightens
For more contrast
For more
brightness
For more color
intensity
Skin tones
become greenish
For more
sharpness
• For resetting all Picture adjustment items to the factory
preset values, press a/b to select "Reset", press ENTER,
press c/d to select "Yes", and then press ENTER.
OPC Setting
Automatically adjusts the brightness of the screen.
Off: The brightness is fixed at the value set in "Backlight".
On: Automatically adjusts.
On: Display: Displays the OPC effect on the screen while
adjusting the brightness of the screen.
• For resetting all adjustment items to the factory preset values,
press a/b to select "Reset", and then press ENTER.
Color Temp.
(Color Temperature)
For a better white balance, use color temperature
correction.
High:
Mid-High:
Middle:
Mid-Low:
Low:
White with bluish tone
White with reddish tone
White balance can be adjusted between a maximum of
+30 and a minimum of –30 for each color temperature.
R Gain: –30 through +30
G Gain: –30 through +30
B Gain: –30 through +30
• For resetting all adjustment items to the factory preset values,
press a/b to select "Reset", and then press ENTER.
Fine Motion Enhanced
Use Fine Motion Enhanced to view fast-action video
more clearly.
On: For obtaining a clearer image.
Off: Normal image.
• Fine Motion Enhanced may cause image noise. If this
occurs, turn the function "Off".
Active Contrast
Automatically adjusts the image contrast according to
the scene.
On: Automatically adjusts the image contrast.
Off: No adjustment.
21
LC-52D85UN_E_03.indd 21
2009/04/06 16:35:17
On-Screen Display Menu
Gamma Adjustment
Adjust mid-level brightness. The adjustment range of the
gamma can be set to a maximum of +2 and a minimum
of –2 by pressing c or d.
Audio Menu
You can adjust the sound quality to your preference
with the following settings.
Example
Film Mode (3:2 pull-down)
Automatically detects a film-based source (originally
encoded at 24 frames/second), analyzes it then recreates
each still film frame for high-definition picture quality.
Audio
Advanced(High)/Advanced(Low): Select a desired level
to remove jerkiness from film contents.
Standard: Detects, analyzes, converts film source.
Off: Normal viewing mode.
• "Standard" does not function when channel display shows
an input signal resolution of 480p, 720p or 1080p.
• "Film Mode" does not function when you set the "AV Mode"
to "Game".
• "Film Mode" is not available during PC format input.
Treble
[ 0]
a15
b15
Bass
[ 0]
a15
b15
Balance
[ 0]
L
R
Surround
[Off]
Bass Enhancer
[On]
Reset
Digital Noise Reduction
Produces a clearer video image.
Off: No adjustment
High/Middle/Low: Select a desired level for viewing a
clearer video image.
• "Digital Noise Reduction" is not available during PC format
input.
3D-Y/C
Provides high quality images with minimal dot crawl
and cross color noise.
Slow: For still images.
Standard: Normal adjustment.
Fast: For moving images.
1 Press MENU to display the MENU screen, and then
press c/d to select "Audio".
2 Press a/b to select a specific adjustment item.
• Select "Surround" or "Bass Enhancer" and then press
ENTER to set each item.
3 Press a/b (or c/d) to select the desired setting,
and then press ENTER.
4 Press MENU to exit.
Selected item
Treble
cbutton
For weaker treble
dbutton
For stronger treble
Bass
For weaker bass
For stronger bass
Balance
Decrease audio from
the right speaker
Decrease audio from
the left speaker
• 3D-Y/C is available for input signal from Composite Video
and analog broadcasts (air and cable).
Monochrome
For viewing a video in monochrome.
On: For viewing in monochrome.
Off: Normal color.
Range of OPC
The brightness level range of the OPC sensor's automatic
adjustments can be set according to your preferences.
The adjustment range of the OPC sensor can be set to
a maximum of +16 and a minimum of –16.
Max.: –15 through +16
Min.: –16 through +15
• The range of OPC settings are active only when the OPC is
set to "On".
• The maximum setting cannot be set to a smaller number
than the minimum setting.
• The minimum setting cannot be set to a bigger number
than the maximum setting.
• Depending on the brightness of the surrounding light, the OPC
sensor might not operate if the adjustment range is small.
• Audio menu is grayed out when Output Select is set to
"Variable". (See page 29.)
• For resetting all Audio adjustment items to the factory
preset values, press a/b to select "Reset", press ENTER,
press c/d to select "Yes", and then press ENTER.
Surround
Surround function allows you to enjoy realistic "live" sound.
On: Surround function is on.
Off: Normal sound.
• You can choose Surround by pressing SURROUND on the
remote control unit. (See page 15.)
• Audio menu is grayed out when Output Select is set to
"Variable". (See page 29.)
• For some discs, setup may be required on your DVD player. In this
case, please refer to the operation manual of your DVD player.
Bass Enhancer
This function allows you to enjoy bass-enhanced sound.
On: Bass Enhancer function is on.
Off: Normal sound.
• Audio menu is grayed out when Output Select is set to
"Variable". (See page 29.)
22
LC-52D85UN_E.indb 22
2009/03/19 17:29:54
On-Screen Display Menu
Power Control Menu
Setup Menu
Power control setting allows you to save energy.
Example
Example
Setup
Power Control
EZ Setup
Power Saving
[Off]
No Signal Off
[Disable]
Antenna Setup-DIGITAL
No Operation Off
[Disable]
Input Skip
1 Press MENU to display the MENU screen, and then
2
3
4
press c/d to select "Power Control".
Press a/b to select a specific adjustment item,
and then press ENTER.
Press a/b (or c/d) to select the desired setting,
and then press ENTER.
Press MENU to exit.
Power Saving
This function allows you to set the Power Saving level
in order to decrease the power consumption and
increase the backlight lifespan.
Standard: Optimizes power reduction based upon video
content. When set to "Standard", " " appears on the
screen.
Advanced: Optimizes power reduction based upon video
content and engages OPC. When set to "Advanced",
" appears on the screen.
"
Off: This function does not work.
• "Power Saving" does not function when you set "AV
MODE" to "DYNAMIC (Fixed)".
• You cannot select a different Power Saving item for each
AV MODE.
When “Power Saving” is set, the “OPC” settings for all AV
Modes will automatically change.
—If you set “OPC” to “On” when “Power Saving” is set
to “Standard”, then the “Power Saving” setting will
change to “Advanced”.
—When you change the “Power Saving” setting from
“Advanced” to “Off” or to “Standard”, “OPC” will be set
to “Off”.
—“DYNAMIC (Fixed)” will remain set to “Off”.
• When "Power Saving" is set to "Standard" or "Advanced",
the Power Saving leaf icon appears to the left of "OPC" in
the Picture menu screen.
• You can select Power Saving by pressing POWER
SAVING on the remote control unit. (See page 17.)
No Signal Off
When set to "Enable", the power will automatically shut
down if there is no signal for 15 minutes.
• When it is 5 minutes before the power shuts down, the
remaining time will start to keep appearing every minute.
• "Disable" is the factory preset value.
• When a TV program finishes, this function may not operate.
No Operation Off
When set to "Enable", the power will automatically shut
down if there is no operation for 3 hours.
CH Setup
Parental CTRL
Position
Language
[English]
Reset
1 Press MENU to display the MENU screen, and then
press c/d to select "Setup".
2 Press a/b to select a specific adjustment item,
and then press ENTER.
• When you select "EZ Setup", "CH Setup", "Parental
CTRL" or "Reset", you can enter the 4-digit secret
number here. See page 25 for setting a secret number.
3 Press a/b (or c/d) to select the desired setting,
and then press ENTER.
4 Press MENU to exit.
EZ Setup
You can run EZ Setup again, even after setting up the
preset channels.
Language: Select from among 3 languages (English,
French and Spanish).
TV Location: Select "Home" or "Store" for the location
where you plan to install the TV. This product qualifies
for ENERGY STAR V3.0 in Home mode default setting.
Home: “Power Saving” is set to "Advanced", and AV MODE is
set to "STANDARD".
Store: “Power Saving” is set to "Off" and AV MODE is set to
"DYNAMIC (Fixed)". Picture Reset and Feature Demo can be
set.
Picture Reset: AV MODE will be set to "DYNAMIC (Fixed)"
regardless of whether Picture Reset is "On" or "Off". If you
select "On", AV MODE will be reset to "DYNAMIC (Fixed)"
if there is no operation for 30 minutes. When "Off" is
selected, AV MODE will be set to "DYNAMIC (Fixed)".
Feature Demo: When “On” is selected, after all the settings
are completed, the Feature Demo screen is displayed if
there is no operation for several minutes.
• ENERGY STAR qualification is based on AV MODE
"STANDARD".
Air/Cable: Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable".
CH Search: Channel auto search makes the TV look for
all channels viewable in the set area.
• See "Initial Setup" on page 14 for setting each item.
• If no channel is found, confirm the type of connection made
with your TV and try EZ Setup again.
• If you select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
• When it is 5 minutes before the power shuts down, the
remaining time will start to keep appearing every minute.
• "Disable" is the factory preset value.
23
LC-52D85UN_E.indb 23
2009/03/19 17:29:54
On-Screen Display Menu
CH Setup
If initial setup does not memorize all the channels in
your region, follow the instructions below to manually
memorize the channels.
Air/Cable: Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable".
CH Search: Channel auto search makes the TV look for
all channels viewable in the set area.
CH Memory: You can select the channels to skip in each
ANALOG (Air), ANALOG (Cable), DIGITAL (Air) and
DIGITAL (Cable).
On: Skips channels. (Channel selection disabled using CH
r/s.)
Off: Does not skip channels. (Channel selection enabled using
CHr/s.)
Remove Scrambled CH: This function makes the TV
look for and then delete digital cable channels that
are scrambled and so unavailable in the set area. The
process may take more than 20 minutes.
Yes: Starts to remove scrambled channels.
No: This function does not work.
• See "Initial Setup" on page 14 for setting each item.
• If no channel is found, confirm the type of connection made
with your TV and try channel search again.
• If you select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
Antenna Setup-DIGITAL
In order to receive digital air broadcasts, you need
a digital broadcast antenna. You can confirm the
antenna configuration through the "Antenna SetupDIGITAL" screen. If necessary, adjust the direction of
the antenna to obtain the maximum signal strength.
Signal Strength: The signal strength of DIGITAL channel
is displayed. The signal information is based on the
current channel.
Channel Strength: Input the 2-digit channel number
to check the signal strength of the selected channel.
Make sure the signal is strong enough for each
channel.
Auto Sync.
(for Analog PC Input Mode Only)
For automatically adjusting the PC image.
Yes: Auto Sync. starts and "Now adjusting the image."
displays.
No: This function does not work.
• When Auto Sync. is successful, "Completed" displays. If
not, Auto Sync. failed.
• Auto Sync. may fail even if "Completed" displays.
• Auto Sync. may fail if the computer image has low
resolution, has unclear (black) edges, or is moved while
executing Auto Sync.
• Be sure to connect the PC to the TV and switch it on before
starting Auto Sync.
Fine Sync.
Ordinarily you can easily adjust the picture as
necessary to change image position using Auto Sync.
In some cases, however, manual adjustment is needed
to optimize the image.
H-Pos.: Centers the image by moving it to the left or
right.
V-Pos.: Centers the image by moving it up or down.
Clock: Adjust when the image flickers with vertical
stripes.
Phase: Adjust when characters have low contrast or
when the image flickers.
• For resetting all Fine Sync. adjustment items to the factory
preset values, press a/b to select "Reset", and then press
ENTER.
• It is not necessary to adjust the "Clock" or "Phase" when a
digital signal is being input, so it cannot be selected.
• The default cursor position may not be in the center,
because the screen position variable ranges may be
asymmetrical.
• The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
position-setting screen.
• This function is available for DIGITAL (Air) only.
Input Skip
This setting allows you to skip the HDMI or PC-IN Input
("Input 4 (PC)", "Input 5 (HDMI)", "Input 6 (HDMI)",
"Input 7 (HDMI)", "Input 8 (HDMI)" and "Input 9 (HDMI)")
on the Input Selection operation.
Yes: Skips the input.
No: Does not skip input.
Input Label
Lets you set the input terminal displayed when using
the INPUT SOURCE menu or channel display. Press
a/b/c/d to select the new name for the input
mode.
• You cannot change labels if the INPUT SOURCE is TV.
24
LC-52D85UN_E.indb 24
2009/03/19 17:29:55
On-Screen Display Menu
Position
For adjusting a picture's horizontal and vertical
position.
H-Pos.: Centers the image by moving it to the left or
right.
V-Pos.: Centers the image by moving it up or down.
• For resetting adjustments to the factory preset values,
press a/b to select "Reset", and then press ENTER.
• When connecting a PC to the HDMI terminal, the image
position will be automatically adjusted. It cannot be
manually adjusted.
• The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
position-setting screen.
• Adjustments are stored separately according to input
source.
Language
You can also select a language from the Setup menu.
Select from among 3 languages: English, French and
Spanish.
■ New Secret No.
You can set and change the secret number by using
0-9.
Input Secret No.: When you change the secret number,
enter the old 4-digit secret number here. The cursor
moves to "New Secret No.".
New Secret No.: When you set the new secret number,
enter the new 4-digit secret number here. The cursor
moves to "Reconfirm".
Reconfirm: Enter the same 4-digit number you set in
"New Secret No.".
■ Secret No. Clear
You can clear your secret number.
Yes: Your secret number is cleared.
No: Your secret number is not cleared.
• As a precautionary measure, make a note of your secret
number and keep it in a familiar place.
• If the secret number is cleared, the Status setting
automatically sets to "Off". "V-Chip" and "Status" will not be
selectable from the menu.
Reset
If complex adjustments are made and the settings
cannot be restored to normal, you can reset the
settings to the factory preset values.
1 "Return to the factory preset values" displays on the
screen.
• If you have already set the Secret No., input the 4-digit
secret number here.
2 Select "Yes".
• "Now, TV will restart automatically. OK?" displays on the
screen.
3 Select "Yes".
• "Now initializing..." displays on the screen and blinks.
After the reset has been completed, the power shuts off
and then comes back on. The screen will have returned
to its original settings.
•
•
•
•
The Channel Setup settings will not be changed.
The Language settings will not be changed.
The Secret number settings will not be changed.
The TV Location settings will not be changed.
Parental CTRL
(Parental Control Setting)
Secret No.
Allows you to use a secret number to protect certain
settings from being accidentally changed.
IMPORTANT:
Three conditions must be met to enable the V-Chip (see
pages 25 to 27):
Status
Used to enable or disable the parental control function.
This function will not be selectable from the menu if
you do not first configure your secret number.
On: Enables Parental CTRL.
Off: Disables Parental CTRL.
V-Chip
V-CHIP is an electronic filtering device built into your
TV. This tool gives parents a great degree of control
over broadcasts accessed by their children. It allows
parents to select programs judged suitable for child
viewing while blocking ones judged not suitable. It
does so automatically once you activate the V-CHIP
feature in your TV. "V-Chip" and "Status" will not be
selectable from the menu if you do not first configure
your secret number.
• The U.S. has two rating systems for viewing content: TV
Parental Guidelines and movie ratings.
• The TV Parental Guidelines work in conjunction with the
V-CHIP to help parents screen out inappropriate television
shows from their children.
• Movie ratings are used for original movies rated by the
Motion Picture Association of America (MPAA) as watched
on cable TV and not edited for television. The V-CHIP can
also be set to block MPAA-rated movies.
• The setting automatically enters "Block" for any ratings
below your selection.
• If Status is not set to "On", the configuration settings will
not work.
1. Secret No. is registered.
2. V-Chip/V-Chip (DTV Only) settings have been made.
• The “V-Chip (DTV Only)” will only be selectable when
a new rating system can be downloaded via digital
broadcasting in the U.S.
3. "Status" is set to "On".
25
LC-52D85UN_E.indb 25
2009/03/19 17:29:55
On-Screen Display Menu
■ MPAA (Voluntary movie rating system)
G: General audiences. All ages admitted.
PG: Parental guidance suggested. Some material may not be
suitable for children.
PG-13: Parents strongly cautioned. Some material may be
inappropriate for children under 13.
R: Restricted. Under 17 requires accompanying parent or
adult guardian (age varies in some jurisdictions).
NC-17: No one 17 and under admitted.
X: X is an older rating that is unified with NC-17 but may be
encoded in the data of older movies.
Example
MPAA
TV Guidelines
G
Can. English Ratings
PG
Can. French Ratings
PG-13
R
NC-17
X
NONE
Press a/b to adjust the item to your desired position.
" " indicates the item is blocked. Press MENU to exit.
• Voluntary movie rating system only uses an age-based
rating.
■ TV Parental Guidelines
Example
Pressa/b to adjust the item to your desired position.
" " indicates the item is blocked. Press MENU to exit.
MPAA
TV Guidelines
TV-Y
Can. English Ratings
TV-Y7
Can. French Ratings
TV-G
L
TV-PG
S
D
TV-14
V
TV-MA
FV
NONE
Example
MPAA
TV Guidelines
TV-Y
Can. English Ratings
TV-Y7
Can. French Ratings
TV-G
L
TV-PG
S
D
TV-14
V
TV-MA
FV
NONE
When setting an individual content-based rating
item:
1 Press d or ENTER to access blocked content
items from the currently selected age-based rating
item.
2 Pressa/b to select an individual item, and then
press ENTER to unblock it (" " is removed). Repeat
the same steps for the other items.
3 Press c or RETURN to register after all individual
content rating items are set.
Content
Rating
FV
(Fantasy
violence)
V
(Violence)
S
(Sexual
situation)
L
(Adult
language)
D
(Sexually
suggestive
dialog)
TV-Y (All children)
TV-Y7 (Directed to older children)
Suggested
age
TV-G (General audience)
TV-PG (Parental Guidance suggested)
TV-14 (Parents strongly cautioned)
TV-MA (Mature audience only)
: The content rating can be set, but this rating is not normally broadcast by TV stations.
: Content rating can be set.
26
LC-52D85UN_E.indb 26
2009/03/19 17:29:56
On-Screen Display Menu
Canadian Rating Systems (Canadian English ratings and Canadian French ratings)
• The TV rating systems in Canada are based on the Canadian Radio-Television and Telecommunications Commission (CRTC)
policy on violence in television programming.
• While violence is the most important content element to be rated, the structure developed takes into consideration other
program content like language, nudity, sexuality and mature themes.
• When setting the V-CHIP on the Canadian system you can choose either the Canadian English ratings or the Canadian French
ratings.
■ Canadian English Ratings
Example
MPAA
TV Guidelines
E
Can. English Ratings
C
C8+
Can. French Ratings
G
PG
14+
18+
NONE
Press a/b to adjust the item to your desired
position. " " indicates the item is blocked.
Press MENU to exit.
■ Canadian French Ratings
Example
MPAA
TV Guidelines
E
Can. English Ratings
G
Can. French Ratings
8ans+
13ans+
16ans+
18ans+
NONE
Press a/b to adjust the item to your desired
position. " " indicates the item is blocked.
Press MENU to exit.
E: Exempt: Includes news, sports, documentaries and other information
programming; talk shows, music videos, and variety programming.
C: Children: Intended for younger children under the age of 8 years.
Pays careful attention to themes that could threaten their sense of
security and well-being.
C8+: Children over 8 years old: Contains no portrayal of violence as the
preferred, acceptable, or only way to resolve conflict; nor encourage
children to imitate dangerous acts which they may see on the screen.
G: General: Considered acceptable for all age groups. Appropriate
viewing for the entire family, contains very little violence, physical,
verbal or emotional.
PG: Parental Guidance: Intended for a general audience, but may not
be suitable for younger children (under the age of 8) because it could
contain controversial themes or issues.
14+: Over 14 years: Could contain themes where violence is one of
the dominant elements of the storyline, but it must be integral to the
development of plot or character. Language usage could be profane
and nudity present within the context of the theme.
18+: Adults: Intended for viewers 18 years and older and might contain
depictions of violence, which while related to the development of plot,
character or themes, are intended for adult viewing. Could contain
graphic language and portrayals of sex and nudity.
E: Exempt programming.
G: General: All ages and children, contains minimal direct violence, but
may be integrated into the plot in a humorous or unrealistic manner.
8ans+: General but inadvisable for young children: May be viewed
by a wide public audience, but could contain scenes disturbing to
children under 8 who cannot distinguish between imaginary and real
situations.
Recommended for viewing with parent.
13ans+: Over 13 years: Could contain scenes of frequent violent scenes
and therefore recommended for viewing with parent.
16ans+: Over 16 years: Could contain frequent violent scenes and
intense violence.
18ans+: Over 18 years: Only for adult viewing. Could contain frequent
violent scenes and extreme violence.
■ How to temporarily release the V-CHIP BLOCK
When the V-CHIP BLOCK is working and censors a broadcast, "V-CHIP HAS BEEN ACTIVATED." displays.
1 Press ENTER while the V-CHIP is working, and then the secret number setting menu displays.
2 Input the 4-digit secret number by using 0-9. At this time V-CHIP BLOCK temporarily releases.
■ Reactivating the temporarily released V-CHIP BLOCK
You can reactivate the temporarily released V-CHIP BLOCK as shown below.
• Select "Status" setting from the Parental CTRL menu to reactivate BLOCK. (See page 25.)
• Select "V-Chip" setting ("MPAA", "TV Guidelines", "Can. English Ratings" or "Can. French Ratings") from the Parental CTRL to
reactivate BLOCK. (See pages 25 to 27.)
• Switch off the TV power.
• Performing any of the three above will activate the V-CHIP BLOCK.
27
LC-52D85UN_E.indb 27
2009/03/19 17:29:58
On-Screen Display Menu
Input Select
Option Menu
If the image does not come in clearly from the external
equipment connected to INPUT 1 or INPUT 2, you
may need to change the input signal type setting on
the "Input Select" menu.
Example
Option
AQUOS LINK Setup
Audio Only
PC Audio Select
Output Select
[Input 4 (PC)]
■ INPUT 2
Select the input signal type from the list below:
Digital Caption Info.
Auto/COMPONENT/S-TERMINAL
[No]
Favorite CH
Game Play Time
[Off]
Operation Lock Out
[Off]
Demo Mode
1 Press MENU to display the MENU screen, and then
2
3
4
Auto/COMPONENT/VIDEO
[Fixed]
Caption Setup
Program Title Display
■ INPUT 1
Select the input signal type from the list below:
press c/d to select "Option".
Press a/b to select a specific adjustment item and
then press ENTER.
Press a/b (or c/d) to select the desired setting,
and then press ENTER.
Press MENU to exit.
Skip this step for "Audio Only".
Audio Only
When listening to music from a music program, you
can turn the screen off and enjoy audio only.
On: Audio is output without screen image.
Off: Both screen images and audio are output.
• The screen image will return to normal when a button
(except those for audio adjustment, such as VOL, MUTE,
SURROUND, AUDIO) is pressed.
Color System
Select the video signal system compatible with your
equipment from the list below:
Auto/NTSC/PAL-M/PAL-N
• If the selected signal type is incorrect, images are not
displayed at all or are displayed without any color.
• Refer to your external equipment operation manual for the
signal type.
• If you set INPUT 1 or 2 to Auto, the TV will automatically
select the input signal.
• Setting INPUT 1 or 2 signal selection to "Auto" when
other equipment is connected will result in the following
connection priority.
INPUT 1:
1 COMPONENT VIDEO
2 VIDEO
INPUT 2:
1 COMPONENT VIDEO
2 S-VIDEO
HDMI Setup
To watch an HDMI or PC-IN equipment image, select
"INPUT5", "INPUT6", "INPUT7", "INPUT8" or "INPUT9"
from "INPUT SOURCE" menu using INPUT on the
remote control unit or on the TV.
Auto View:
Enable: To use View Mode based on signal
recognition, including an HDMI signal.
Disable: No function.
• Refer to your external equipment operation manual for the
signal type.
• When connecting an HDMI-DVI conversion adapter/cable
to the HDMI terminal, the image may not come in clearly.
PC Audio Select
• "Color System" can only be set for the INPUT 1 VIDEO,
INPUT 2 S-VIDEO and INPUT 3 VIDEO.
• If you have already set the Secret No., input the 4-digit
secret number here. See page 25 for setting a secret
number.
Determines whether the AUDIO terminal is used for
INPUT 4 (PC-IN) or INPUT 6 (HDMI).
Input 4 (PC): Select this item when the audio signal is
input via the INPUT 4 (PC-IN) terminal using an analog
RGB cable.
Input 6 (HDMI): Select this item when the audio signal is
input via the INPUT 6 (HDMI) terminal using an HDMIDVI conversion cable.
• When "PC Audio Select" is set to "Input 6 (HDMI)", sound
will not be produced if you use only an HDMI-certified
cable to connect HDMI-compatible equipment. To produce
sound, you should make an analog audio connection.
• If you want to connect HDMI-compatible equipment using
only an HDMI-certified cable, set "PC Audio Select" to
"Input 4 (PC)".
28
LC-52D85UN_E_03.indd 28
2009/04/06 16:35:24
On-Screen Display Menu
Output Select
Allows you to select what controls the audio output.
Fixed: Sound via speaker is adjusted with VOLk/l on
the remote control unit or VOLk/l on the TV.
Sound via the AUDIO OUTPUT terminal is not
adjustable and outputs at a consistent level.
Variable: Sound via the AUDIO OUTPUT terminal is
adjusted with VOLk/l on the remote control unit or
VOLk/l on the TV.
Sound via speaker is muted.
Caption Setup
This function allows you to adjust the closed
caption screen appearance to suit your preference.
You can adjust 7 items: "Caption Size", "Font
Style", "Foreground Color", "Foreground Opacity",
"Background Color", "Background Opacity" and
"Character Edge".
Example:
Selectable items available for "Font Style".
Default: The font specified by broadcasting station or
default font.
Type 0: Proportional font used in the MENU screen.
Type 1: Monospaced with serifs.
Type 2: Proportionally spaced with serifs.
Type 3: Monospaced without serifs.
Type 4: Proportionally spaced without serifs.
Type 5: Casual font type.
Type 6: Cursive font type.
Type 7: Small capitals.
• For resetting adjustments to the factory preset values,
press a/b to select "Reset", and then press ENTER.
• The default value depends on the broadcasting station.
Digital Caption Info.
(Digital Caption Information)
This function allows viewing of digital closed caption
information for the digital broadcast program being
viewed.
• This list is not displayed for analog broadcasts or external
input audio/video.
• This information is not included in CC1, CC2, Text1, or
Text2, and is not displayed in a list.
Program Title Display
Select the CH display when changing channels for
digital broadcasting.
Yes: "Program Info." displays.
No: "Program Info." does not display.
Game Play Time
Operation Lock Out
This function locks the operation buttons on the TV
and the remote control.
Off: No adjustment.
RC Control Lock: All buttons on the remote control are
locked.
Button Control Lock: All buttons on the TV, except
POWER, are locked.
• To unlock the buttons on the remote control, press MENU
on the TV, and then select "Off" on the MENU screen.
• To unlock the buttons on the TV, press MENU on the
remote control, and then select "Off" on the MENU screen.
Favorite CH
(Favorite Channel Setting)
This function allows you to program 4 favorite
channels, in 4 different categories. By setting the
favorite channels in advance, you can select your
favorite channels easily.
To register your favorite channel:
Select "Register" and then press ENTER. Press a/b/c/
d to select the position in the category, and then press
ENTER to register.
To delete your favorite channel:
Select "1 Data Clear" and then press ENTER. Press
a/b/c/d to select the channel you want to delete, and
then press ENTER. Select "Yes" and then press ENTER.
To delete all the favorite channels, select "All Data Clear".
• Before setting the channel, select the channel you want to
register as a favorite channel.
• You can display the "Favorite CH" screen by pressing
FAVORITE on the remote control.
Demo Mode
You can select the image from several types of demo
mode.
120Hz Demo 1/120Hz Demo 2/10 bit Demo/
Feature Demo/Auto Play
If you select "Auto Play", you need to set playback type.
Continuous: Play Demos continuously.
10 min.: Play Demos every 10 minutes.
20 min.: Play Demos every 20 minutes.
• This function will be canceled when you press EXIT on the
remote control unit.
• When "Demo Mode" is set to "Feature Demo", pressing
FREEZE pauses/restarts demo.
• "Demo Mode" may not be selected depending on input
signal type.
• "Demo Mode" may be automatically canceled depending
on input signal type.
This function displays the elapsed game time so you
do not lose track of the time. To display the elapsed
time, select "GAME" for the AV MODE before starting
the game.
On: The elapsed time is displayed every 30 minutes when
you switch to GAME mode in external input mode.
Off: No adjustment.
29
LC-52D85UN_E.indb 29
2009/03/19 17:30:00
On-Screen Display Menu
Digital Setup Menu
This setting allows you to optimize the settings of
Digital broadcasting.
Example
Digital Setup
Audio Setup
Software Update
This function allows software updates by inserting
a USB memory device with the update file into the
SERVICE terminal on the TV.
To check for the availability of a software update, visit
www.sharpusa.com. If you have any questions, please
call 1-800-BE-SHARP (800-237-4277).
[PCM]
Identification
Software Update
1 Press MENU to display the MENU screen, and then
press c/d to select "Digital Setup".
2 Press a/b to select a specific adjustment item,
and then press ENTER.
3 Press a/b (or c/d) to select the desired setting,
and then press ENTER.
4 Press MENU to exit.
Audio Setup
You can output digital audio to an AV amplifier or
similar device whose DIGITAL AUDIO INPUT terminal
is connected to the DIGITAL AUDIO OUTPUT terminal
on the TV. Please select an audio output format
compatible with the audio format of the program you
are watching and the equipment connected.
CAUTION
• Do not remove the USB memory device or unplug the
AC cord while the software is being updated.
• Be sure to properly follow the whole procedure
described below, step by step. Otherwise, for
example, the TV cannot read the data in the USB
memory device and software updating will fail.
1 Insert the USB memory device with the update file
into the SERVICE terminal on the TV.
PCM: The optical output terminal outputs audio signal
in PCM form. If your digital audio system does not
support Dolby Digital, select "PCM".
Dolby Digital: The optical output terminal outputs audio
signal in Dolby Digital form. It reproduces sound from
surround program of digital.
Identification
The current version of the TV software is displayed.
2 Press MENU to display the MENU screen, and
then press c/d to select “Digital Setup”.
3 Press a/b to select “Software Update”, and then
press ENTER.
• If you have already set the Secret No., go to step 4.
Digital Setup
Audio Setup
[PCM]
Identification
Software Update
4 Input the 4-digit secret number by using 0–9.
Digital Setup
Secret No.
a a a a
30
LC-52D85UN_E.indb 30
2009/03/19 17:30:00
On-Screen Display Menu
5 Press ENTER to start checking the data in the
USB memory device.
Insert the USB memory device containing
the software update file.
7 Press ENTER to start updating.
• The screen becomes dark for a while until the update
screen can be displayed. Please wait for the update
screen to appear. Do not unplug the AC cord.
The picture will temporarily go dark until
the Software Update display appears.
Wait several minutes and do not unplug the AC cord.
OK
OK
6 During the data checking, “Checking” blinks.
Now checking the data in the USB memory device.
Example
Now updating
Do not unplug AC cord.
Checking
Update Version
• The current version of the TV software and the version
of the update file on the USB memory device are
displayed. To update the TV software with the update
file, select “Yes”, and then press ENTER.
Example
CAUTION
8 When the software is successfully updated, a
UXXXXXX1
UXXXXXX2
Yes
30%
• Do not remove the USB memory device or unplug the
AC cord while the software is being updated.
Software update file is detected
in the USB memory device.
Start update?
Current Version:
Update Version:
UXXXXXX2
No
screen is displayed indicating that the update
process is completed.
After this screen is displayed, the TV automatically
turns off and then turns on again.
Example
• If the USB memory device is not properly installed or
the correct update file cannot be found on the USB
memory device, an error message is displayed.
Check the file on the USB memory device, and then
reinsert the USB memory device correctly.
Software update file is not detected
in the USB memory device.
Confirm that you have transferred the file
to the USB memory device and retry software update.
Software update is complete.
Update Version
• If the update has failed, check the file in the USB
memory device and try Software Update again.
OK
There is more than one software file
in the USB memory device.
Confirm that only the software update file is
in the USB memory device.
UXXXXXX2
Failed to complete update.
Retry Software Update.
If system Update fails again,
contact the customer service center.
9 After the screen shown below is displayed, press
ENTER.
OK
System software was
successfully updated.
Remove the USB memory device.
OK
10 Remove the USB memory device.
31
LC-52D85UN_E.indb 31
2009/03/19 17:30:01
Other Viewing Options
Presetting Remote Control Function
You can operate the connected AV products (AV
receiver, cable box, SAT tuner, DTV, VCR, DVD, LD)
using the presetting manufacturer function of your
remote control unit.
Operating the Connected Equipment
To operate the connected equipment, press
FUNCTION to select the LED for your device. (VCR,
AUDIO, CBL/SAT (cable converter) or DVD.) The
LED lights up, and the remote control unit button will
function as follows.
• When you operate VCR or DVD, press INPUT to select the
terminal connected to your device.
• CABLE and SAT cannot be selected at the same time.
1 SOURCE POWER
1
2
3
4
6
7
8
9
10
• Turns the connected equipment power on and off.
2G
• Rewinds the tape and allows picture search. (VCR)
• Hold down to go in reverse. (DVD)
3 REC
• Starts recording. (VCR)
5
4K
• Pressing quickly once takes you to the start of the chapter
currently playing. Each time you press it, you move back
to the start of the previous chapter. (DVD)
11
12
5 0–9 (CBL/SAT), • (DOT) (SAT)
• Press a button (or buttons) that corresponds to the
channel that you wish to watch.
6I
• Starts playback. (VCR, DVD)
13
14
7J
• Rapidly advances the tape and allows picture search.
(VCR)
• Hold down to fast forward. (DVD)
8F
• Sets pauses and still pictures. (VCR, DVD)
9H
• Stops the tape transport. (VCR)
• Playback stops when pressed. With some DVD players,
pressing the button twice may open the disc tray. (DVD)
10 L
Presetting manufacturer codes
1 Press FUNCTION until the LED for your device
lights up.
2 After the LED for your device lights up, press
FUNCTION and DISPLAY at the same time to
enter the code registration mode. The LED will
blink.
3 Press 0–9 to enter the manufacturer code. (See
• Pressing quickly once takes you to the start of the next
chapter. Each time you press it, you move ahead to the
start of the next chapter. (DVD)
11 FLASHBACK
• Press to switch between the current channel and the
channel you were watching immediately before. Some
manufacturers do not preset FLASHBACK. (CBL)
12 CHr/s
• Press CHr or CHs to tune in to a higher or lower
channel. (CBL)
• Press to select the channel of the TV tuner on the VCR.
(VCR)
page 33.)
13 MENU
• Preset mode is finished once the LED no longer lights
up.
14 a/b/c/d, ENTER
4 After registering the code, the LED will stop blinking
then turn off after one second. (If you perform an
incorrect operation, the LED will blink quickly then
turn off.)
• When this button is pressed, the DVD menu will display.
• a/b/c/d: Press the button to select items on the SAT
GUIDE screen or SAT MENU screen. (SAT). Press the
button to select items on the DVD MENU screen. (DVD)
• ENTER: Press to activate the selected function. (SAT,
DVD)
32
LC-52D85UN_E.indb 32
2009/03/19 17:30:01
Other Viewing Options
Manufacturer codes
VCR BRAND
REMOTE CONTROL CODE
NUMBER
DVD/BD/LD BRAND
REMOTE CONTROL CODE
NUMBER
CATV/SAT BRAND
REMOTE CONTROL CODE
NUMBER
• Numbers marked with * are SAT codes, all others are
CATV codes.
AUDIO BRAND
REMOTE CONTROL CODE
NUMBER
33
LC-52D85UN_E.indb 33
2009/03/19 17:30:02
Using AQUOS LINK
Controlling HDMI Equipment Using AQUOS LINK
What’s AQUOS LINK?
• Using the HDMI CEC (Consumer Electronics Control) protocol, with AQUOS LINK you can interactively operate
compatible system equipment (Blu-ray disc equipment, AV amplifier, DVD).
• By connecting AQUOS LINK-compatible devices with HDMI-certified cables to the TV, you can control a
recorder or AV amplifier using the remote control of the TV.
• AQUOS LINK allows you to operate the HDMI-connected equipment with one remote control.
Example*
HDMI-certified cable
(commercially available)
AQUOS LINK-compatible
Audio system
Optical fiber cable
(commercially available)
HDMI-certified cable
(commercially available)
AQUOS BD Player
* You can use the INPUT 5,
6, 7, 8 or 9 terminal.
Connecting AQUOS
BD Player via AQUOS
LINK-compatible
Audio system
TV
•
•
•
•
Point the remote control toward the TV, not to connected HDMI equipment.
Video noise may occur depending on the type of HDMI cable used. Make sure to use an HDMI-certified cable.
Up to 3 pieces of HDMI recording equipment and one AV amplifier can be connected using this system.
These operations affect the HDMI equipment selected as the current input source. If the equipment does not operate, turn on
the equipment and select the appropriate input source using INPUT.
You can operate AQUOS LINK-compatible devices with the remote control
unit when the FUNCTION of the remote control unit is set to TV.
REC STOP and OPTION buttons will function only when AQUOS LINK is
used.
■ One Touch Play
While the TV is in standby mode, it automatically turns on and plays back the
image from the HDMI source.
■ One Touch Recording
Press REC while you are viewing a broadcast received with the AQUOS
LINK-compatible recorder. The AQUOS LINK automatically recognizes the
connected HDMI device and starts recording.
■ Single remote control
The AQUOS LINK automatically recognizes the connected HDMI device and
you can control the TV and the devices as if using a universal remote control.
■ Control the AQUOS LINK-compatible audio system
Set the volume of AQUOS LINK-compatible audio system.
• The above description is an example of the AQUOS LINK function.
• The steps in “AQUOS LINK Setup” on page 35 need to be completed beforehand.
• Refer to this operation manual and the operation manual of the AQUOS LINK device to be used with this TV.
34
LC-52D85UN_E_05.indd 34
2009/04/06 17:41:15
Using AQUOS LINK
Selecting Recorder
When multiple AQUOS LINK-compatible devices are
connected, this function allows you to set the recorder
for recording when you press REC on the TV’s remote
control unit.
AQUOS LINK Setup
1 Press MENU to display the MENU screen, and then
press c/d to select "Option".
Press a/b to select the recorder for recording.
Example
AQUOS LINK Control
2 Press a/b to select “AQUOS LINK Setup”, and
then press ENTER.
Auto Power On
Selecting Recorder
3 Press a/b to select a specific item, and then press
ENTER.
Input
Location
INPUT5
[1.0.0.0]
INPUT6
[2.0.0.0]
4 Press a/b (or c/d ) to select the desired setting,
and then press ENTER.
5 Press MENU to exit.
AQUOS LINK Control
Select AQUOS LINK Control to disable AQUOS LINK
function even when an AQUOS LINK-compatible HDMI
device is connected to the TV. This function prevents
the device from starting to operate unexpectedly.
Enable: You can operate AQUOS LINK-compatible
equipment.
Disable: AQUOS LINK function does not work.
Example : when connecting AQUOS LINK-compatible
recorder via AQUOS LINK-compatible Audio
system
AQUOS LINK Control
Auto Power On
Selecting Recorder
Input
Location
INPUT5
5WD
[1.1.0.0]
INPUT6
[2.0.0.0]
When an AQUOS LINK-compatible audio system or
other equipment is connected between the TV and
recorder, “Sub” is displayed.
AQUOS LINK Control
Auto Power On
Selecting Recorder
One Touch Recording
Enable
Disable
Auto Power On
If this is activated, the One Touch Play function is
enabled.
This function allows easy one-touch recording of the
program being viewed on the TV to AQUOS LINKcompatible equipment with a recording function by
simply pressing REC on the remote control.
Yes: While the TV is in standby mode, it automatically
turns on and plays back the image from the HDMI
source.
No: This function does not work.
AQUOS LINK Control
Auto Power On
Selecting Recorder
Yes
No
Prepare the connected AQUOS LINK-compatible
recorder for recording. Check the following items.
• Make sure that the antenna cable is connected.
• Check that there is sufficient available space on the
recording media (HDD, DVD, etc.).
• On the TV, use “AQUOS LINK Setup” and “Selecting
Recorder” to select the equipment for recording.
• By default, the recorder connected to INPUT 5 is selected
for recording.
1 Press REC to start recording.
• When you are viewing a broadcast received with
the AQUOS LINK-compatible recorder selected in
"Selecting Recorder", recording to the AQUOS recorder
of the broadcast being viewed starts.
• When you are viewing a broadcast received with
equipment other than the AQUOS LINK-compatible
recorder selected in "Selecting Recorder" or other
external input equipment, pressing REC on the remote
control does not start recording.
2 Press REC STOP to stop recording.
35
LC-52D85UN_E.indb 35
2009/03/19 17:30:03
Using AQUOS LINK
AQUOS LINK Menu
One Touch Playback
AQUOS LINK allows you to operate the HDMIconnected equipment with one remote control.
AQUOS LINK
Recorder EPG
Top menu/title list
Media change
By AQUOS AUDIO SP
Press d to start playing back a title.
By AQUOS SP
• The last played program is played back. You can use the
following buttons during broadcast viewing.
Buttons
SOURCE
POWER
G
I
J
Sound mode change
Setup menu
Description
Turns the power of the HDMI connected
devices on and off.
Model select
Hold down to go in reverse.
Starts playback.
Hold down to fast forward.
H
Playback stops.
F
Sets pauses and still pictures.
T
Pressing quickly once takes you to the start
of the chapter currently playing. Each time
you press it, you move back to the start of
the previous chapter.
U
Pressing quickly once takes you to the start
of the next chapter. Each time you press
it, you move ahead to the start of the next
chapter.
• You can use T/U only when the model BD-HP21U is
connected.
• The buttons T/U do not function with the following
BD players currently available.
- BD-HP20U, BD-HP50U
Timer Recording
You can call up the AQUOS LINK-compatible
recorder’s EPG and preset timer recordings using the
TV’s remote control.
1 Press OPTION to display the AQUOS LINK MENU
screen.
2 Press a/b to select “Recorder EPG”, and then
press ENTER.
• The recorder’s EPG is displayed.
3 Select the program to record.
• You can use a/b/c/d, ENTER, RETURN, EXIT and
the coloured buttons.
• This function works only when an AQUOS LINK-compatible
recorder is connected.
• Refer to the operation manual of the recorder for details.
36
LC-52D85UN_E.indb 36
2009/03/19 17:30:04
Using AQUOS LINK
Playback of Titles Using AQUOS LINK
This section explains how to play back a title in the
AQUOS LINK-compatible equipment.
1 Power on the AQUOS LINK-compatible equipment,
and select appropriate external input.
2 Press OPTION to display the AQUOS LINK MENU
screen.
3 Press a/b to select “Top menu/title list”, and then
press ENTER.
• The title list data from the connected AQUOS LINKcompatible equipment displays.
4 Select the title with a/b/c/d, and then press d
to start playback.
• This function works only when AQUOS LINK-compatible
equipment is connected.
Selecting Media Type for AQUOS LINKCompatible Recorder
You can switch the media (HDD or DVD) for playback
or recording on the AQUOS LINK-compatible recorder.
1 Press OPTION to display the AQUOS LINK MENU
screen.
2 Press a/b to select “Media change”, and then
press ENTER.
3 Select the desired media such as DVD or HDD.
• The Media type toggles each time you press ENTER in
“Media change”.
• Select the media to be operated by the player.
Listening with the AQUOS AUDIO Speaker System
You can select to listen to the TV sound only from the
AQUOS LINK-compatible audio system and manually
change its sound mode.
1 Press OPTION to display the AQUOS LINK MENU
screen.
2
Manually Changing AQUOS AUDIO Speaker
System’s Sound Mode
1 Press OPTION to display the AQUOS LINK MENU
screen.
2 Press a/b to select “Sound mode change”, and
then press ENTER.
• The sound mode changes each time you press ENTER.
• Refer to the operation manual of the AQUOS LINKcompatible audio system for details.
Displaying the Setup Menu of AQUOS
LINK-Compatible Equipment
You can call up a setup menu from the connected
AQUOS LINK-compatible equipment.
1 Press OPTION to display the AQUOS LINK MENU
screen.
2 Press a/b to select "Setup menu", and then press
ENTER.
• The setup menu of the AQUOS LINK-compatible
equipment is displayed.
• Depending on the status of the equipment (recording or in
standby mode, etc), the setup menu will not be displayed.
• This function works only when the model BD-HP21U or
BD-HP50U is connected.
• The setup menu will not be displayed with the player
BD-HP20U currently available.
HDMI Device Selection
If multiple HDMI devices are connected in a daisy
chain, you can specify which device to control here.
1 Press OPTION to display the AQUOS LINK MENU
screen.
2 Press a/b to select “Model select”, and then
press ENTER. The HDMI device toggles each time
you press ENTER.
Press a/b to select “By AQUOS AUDIO SP”, and
then press ENTER.
• The sound from the TV speaker is muted and only the
sound from the AQUOS LINK-compatible audio system
is audible.
• You can use VOLk/l and MUTE.
Select “By AQUOS SP”, and then press ENTER to
listen to the TV sound.
37
LC-52D85UN_E.indb 37
2009/03/19 17:30:04
Appendix
Removing the Stand
• Before detaching (or attaching) the stand, unplug the AC cord from the AC INPUT terminal.
CAUTION
• Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
Before attaching/detaching the stand
• Before performing work, make sure to turn off the TV.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being
damaged.
1
2
Hex key
Unfasten the four screws used to secure the stand in
place.
Detach the stand from the TV. (Hold the stand so it
will not drop from the edge of the base area.)
• To attach the stand, perform the above steps in reverse order.
Setting the TV on the Wall
CAUTION
• This TV should be mounted on the wall only with the wall mount bracket AN-52AG4 (SHARP). The use of other wall
mount brackets may result in an unstable installation and may cause serious injuries.
• Installing the TV requires special skill that should only be performed by qualified service personnel. Customers
should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or mounting
that results in accident or injury.
Using an optional bracket to mount the TV
• You can ask a qualified service professional about using an optional AN-52AG4 bracket to mount the TV on the wall.
• Carefully read the instructions that come with the bracket before beginning work.
Hanging on the wall
AN-52AG4 wall mount bracket.
(See the bracket instructions for details.)
About setting the TV angle
/15/20°
0/5/10
LC-46D85UN
• The “ b ” position is at the
center of the display.
LC-52D85UN
• The center of the display:
19
/64 inch (7.3 mm) under
the “ f ” position.
• Refer to the operation
manual of AN-52AG4 for
details.
Vertical mounting
Angular mounting
• Detach the cable clamp on the rear of the TV when using the optional mount bracket.
• To use this TV mounted on a wall, remove the covers at the 4 locations on the rear of the TV, and then use the screws
supplied with the wall mount bracket to secure the bracket to the rear of the TV.
38
LC-46_52D85UN_E_06.indd 38
2009/04/10 15:42:23
Appendix
Troubleshooting
Problem
Possible Solution
• No power
• Check if you pressed TV POWER on the remote control unit. (See page 14.) If the
indicator on the TV does not light up, press POWER on the TV.
• Is the AC cord disconnected? (See page 7.)
• Has the power been turned on? (See page 14.)
• Unit cannot be operated.
• External influences such as lightning, static electricity, may cause improper operation.
In this case, operate the unit after first turning off the power of the TV or unplugging
the AC cord and replugging it in after 1 or 2 minutes.
• Remote control unit does not
operate.
•
•
•
•
•
• Picture is cut off/with sidebar
screen.
• Is the image position correct? (See page 25.)
• Are screen mode adjustments such as picture size made correctly? (See page 18.)
• Strange color, light color, or color
misalignment
• Adjust the picture tone. (See pages 21 and 22.)
• Is the room too bright? The picture may look dark in a room that is too bright.
• Power is suddenly turned off.
• Is the sleep timer set? (See page 15.)
• Check the power control settings. (See page 23.)
• The unit's internal temperature has increased. Remove any objects blocking vent or
clean.
• No picture
•
•
•
•
•
•
• No sound
• Is the volume too low? (See page 15.)
• Is “Variable” selected in “Output Select”? (See page 29.)
• Have you pressed MUTE on the remote control unit? (See page 15.)
• The TV sometimes makes a
cracking sound.
• This is not a malfunction. This happens when the cabinet slightly expands and
contracts according to change in temperature. This does not affect the TV's
performance.
Is the FUNCTION set correctly? Set it to the TV setting position.
Are batteries inserted with polarity (e, f) aligned? (See page 8.)
Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light illuminated near the remote control sensor?
Is connection to other components correct? (See pages 12 and 13.)
Is correct input signal source selected after connection? (See page 28.)
Is the correct input selected? (See page 28.)
Is picture adjustment correct? (See pages 21 and 22.)
Is “On” selected in “Audio Only”? (See page 28.)
Is a non-compatible signal being input? (See page 42.)
Troubleshooting-Digital Broadcasting
The error message about reception of broadcast
The example of an error message
displayed on a screen
Error code
Possible Solution
• Failed to receive broadcast.
E202
• Check the antenna cable. Check that the antenna is correctly
setup.
• No broadcast now.
E203
• Check the broadcast time in the program guide.
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.
This is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the Liquid Crystal panel to malfunction.
Storage temperature: f4°F to e140°F (f20°C to e60°C)
39
LC-52D85UN_E.indb 39
2009/03/19 17:30:05
Appendix
RS-232C Port Specifications
■ PC control of the TV
• Attach an RS-232C cable cross-type (commercially
available) to the supplied Din/D-Sub RS-232C for the
connections.
■ Command format
Eight ASCII codes e CR
C1 C2 C3 C4 P1 P2 P3
Command 4-digits
• This operation system should be used by a person who is
accustomed to using computers.
■ Communication conditions
Set the RS-232C communication settings on the PC to
match the TV's communication conditions.
The TV's communication settings are as follows:
Baud rate:
Data length:
Parity bit:
Stop bit:
Flow control:
9,600 bps
8 bits
None
1 bit
None
P4
Parameter 4-digits
Return code
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter 0–9, x, blank, ?
■ Parameter
Input the parameter values, aligning left, and fill with
blank(s) for the remainder. (Be sure that 4 values are
input for the parameter.)
When the input parameter is not within an adjustable
range, “ERR” returns. (Refer to “Response code format”.)
Any numerical value can replace the “x” on the table.
0
0
0
0
9
When “?” is input for some
commands, the
?
present setting
value responds.
■ Communication procedure
?
?
?
?
a
3
0
Send the control commands from the PC via the RS232C connector.
■ Response code format
The TV operates according to the received command
Normal response
Problem response (communication
and sends a response message to the PC.
error or incorrect command)
O K
Do not send multiple commands at the same time.
E R R
Wait until the PC receives the OK response before
Return code (0DH)
Return code (0DH)
sending the next command.
■ Command table
• Commands not indicated here are not guaranteed to operate.
CONTROL ITEM
POWER ON COMMAND SETTING
POWER SETTING
INPUT SELECTION A TOGGLE
TV
INPUT1-9
INPUT SELECTION B INPUT 1
INPUT 2
AV MODE SELECTION
VOLUME
POSITION
VIEW MODE
V
H-POSITION H
V-POSITION V
CLOCK
C
PHASE
P
W
O
P
P
L
H
I
L
O
O
C
S
D
M
S
S
K
E
E
*
*
*
*
*
*
*
*
*
*
*
_
_
*
*
*
*
_
_
_
_
_
_
_
M
A
A
O
U
C
C
F
T
S
H
T
E
U
A
M
*
*
x
*
_
_
_
_
_
_
_
_
_
_
_
_
D C C H
*
*
*
D A 2 P
D C 2 U
*
*
*
*
*
*
D C 2 L
*
*
*
D
D
C
C
C
*
*
x
x
x
*
*
_
_
_
*
*
_
_
_
MUTE
SURROUND
AUDIO SELECTION
SLEEP TIMER
CHANNEL
DIRECT
CHANNEL
(ANALOG)
DIRECT
CHANNEL
(DIGITAL)
CH UP
CH DOWN
CC
COMMAND PARAMETER
R S P W 0 _ _ _ Off
1 _ _ _ On
P O W R 0 _ _ _ Power Off
1 _ _ _ Power On
I T G D x _ _ _ (Toggle)
I T V D 0 _ _ _
I A V D * _ _ _ Input terminal number (1–9)
I N P 1 * _ _ _ 0: Auto, 1: VIDEO, 2: COMPONENT
I N P 2 * _ _ _ 0: Auto, 2: COMPONENT, 3: S-TERMINAL
A V M D * _ _ _ 0: (Toggle), 1: STANDARD, 2: MOVIE, 3: GAME, 4: USER,
5: DYNAMIC (Fixed), 6: DYNAMIC, 7: PC
C
C
H
H
L
1
1
U
D
C
0
1
P
W
P
CONTROL CONTENTS
The Power On command rejected.
The Power On command accepted.
It shifts to standby.
Power On
It input-switches by the toggle. (It is the same as an input change key)
It input-switches to TV. (A channel remains as it is. (Last memory))
It input-switches to INPUT1~INPUT9.
An input change is also included.
Although it can choose now, it is toggle operation in inside.
Volume (0–60)
The screen position variable ranges depend on the View Mode or the
signal type. The ranges can be seen on the position-setting screen.
Only PC mode. (0–180)
Only PC mode. (0–40)
0: (Toggle) [AV], 1: Side Bar [AV], 2: S.Stretch [AV]
3: Zoom [AV], 4: Stretch [AV], 5: Normal [PC]
6: Zoom [PC], 7: Stretch [PC],
8: Dot by Dot [PC] [AV], 9: Full Screen [AV]
0: Although it can choose now, it is toggle operation in inside.
1: Only available when 4:3 signal is being input.
5, 6: Only available when 4:3 signal is being input.
8: [PC] Available except when UXGA is being input.
[AV] Only available when 1080i/p is being input.
9: Only available when 720p is being input.
0: (Toggle), 1: On, 2: Off
0: (Toggle), 1: On, 2: Off
(Toggle)
0: Off, 1: OFF TIMER – 30 MIN., 2: OFF TIMER – 60 MIN.,
3: OFF TIMER – 90 MIN., 4: OFF TIMER – 120 MIN.
_ The channel number of TV
An input change is included if it is not TV display.
In Air, 2–69ch is effective.
(1–135)
In Cable, 1–135ch is effective.
DIGITAL Air (Two-Part numbers, 2-digit plus 2-digit)
* (0100-9999)
_ (1-999)
DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)
Front half of DIGITAL CABLE CHANNEL NO. (Designate major channel)
_ (0-999)
DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)
Rear half of DIGITAL CABLE CHANNEL NO. (Designate minor channel)
* (0-9999)
DIGITAL Cable (One-Part numbers, 5-digit, less than 10,000)
* (0-6383)
DIGITAL Cable (One-Part numbers, 5-digit, more than 10,000)
If it is not TV display, it will input-switch to TV. (same function as CHU)
_ The channel number of TV +1
If it is not TV display, it will input-switch to TV. (same function as CHV)
_ The channel number of TV –1
Toggle operation of a closed caption.
_ (Toggle)
• If an underbar (_) appears in the parameter column, enter a space.
• If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.
• Any numerical value can replace the “x” on the table.
40
LC-52D85UN_E.indb 40
2009/03/19 17:30:06
Appendix
Specifications
Item
Model: LC-46D85UN
Model: LC-52D85UN
LCD panel
46o Class (45 63/64o Diagonal)
Advanced Super View & BLACK TFT LCD
52o Class (52 1/32o Diagonal)
Advanced Super View & BLACK TFT LCD
Resolution
2,073,600 pixels (1,920 g 1,080)
TV-standard (CCIR)
TV
Function
Receiving
Channel
American TV Standard ATSC/NTSC System
VHF/UHF
VHF 2-13ch, UHF 14-69ch
CATV
1-135ch (non-scrambled channel only)
Digital Terrestrial
Broadcast (8VSB)
2-69ch
*1
Digital cable
(64/256 QAM)
Audio multiplex
Backlight
1-135ch (non-scrambled channel only)
BTSC System
60,000 hours (at Backlight Standard position)
10W g 2
Audio out
INPUT 1
Rear
Terminals
Side
AV in, COMPONENT in
INPUT 2
COMPONENT in, S-VIDEO in
INPUT 4
ANALOG RGB (PC) in (15-pin mini D-sub female connector), Audio in (Ø 3.5 mm jack)
INPUT 6
HDMI in with HDCP, Audio in (Ø 3.5 mm jack)
INPUT 7
HDMI in with HDCP
INPUT 8
HDMI in with HDCP
INPUT 9
HDMI in with HDCP
ANT/CABLE
75 q Unbalance, F Type g 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
AUDIO
Audio in (Ø 3.5 mm jack)
DIGITAL AUDIO OUTPUT
Optical Digital audio output g 1 (PCM/Dolby Digital)
OUTPUT
Audio out
RS-232C
9-pin D-sub male connector
INPUT 3
AV in
INPUT 5
HDMI in with HDCP
SERVICE
Software update
OSD language
English/French/Spanish
Power Requirement
AC 120 V, 60 Hz
Power Consumption
Weight
*2
Dimension
(W g H g D)
254 W (0.4 W Standby with AC 120 V)
290 W (0.4 W Standby with AC 120 V)
TV + stand
50.7 lbs./23.0 kg
61.7 lbs./28.0 kg
TV only
40.8 lbs./18.5 kg
TV + stand
TV only
Operating temperature
53
45
53
47
51.8 lbs./23.5 kg
61
49 19/64 g 33 25/64 g 12 61/64 inch
43 /64 g 29 /64 g 12 /64 inch
29
49 19/64 g 31 11/32 g 3 25/32 inch
43 /64 g 27 /64 g 3 /32 inch
e32°F to e104°F (0°C to e40°C)
*1
Emergency alert messages via Cable are unreceivable.
The dimensional drawings are shown on the inside back cover.
• As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product
improvement without prior notice. The performance specification figures indicated are nominal values of production units.
There may be some deviations from these values in individual units.
*2
Optional Accessory
The listed optional accessory is available for the Liquid
Crystal Television. Please purchase it at your nearest shop.
Part name
Model number
Wall mount bracket
AN-52AG4
• Additional optional accessories may be available in the near
future. When purchasing, please read the newest catalogue for
compatibility and check the availability.
41
LC-46_52D85UN_E_06.indd 41
2009/04/17 15:56:45
PC Compatibility Chart
It is necessary to set the PC correctly to display XGA and WXGA signal.
PC
Resolution
720 x 400
VGA
640 x 480
SVGA
800 x 600
XGA
1024 x 768
WXGA
SXGA
SXGA+
UXGA
1360 x 768
1280 x 1024
1400 x 1050
1600 x 1200
PC
Horizontal Frequency
31.5 kHz
31.5 kHz
37.9 kHz
37.5 kHz
35.1 kHz
37.9 kHz
48.1 kHz
46.9 kHz
48.4 kHz
56.5 kHz
60.0 kHz
47.7 kHz
64.0 kHz
65.3 kHz
75.0 kHz
Vertical Frequency
70 Hz
60 Hz
72 Hz
75 Hz
56 Hz
60 Hz
72 Hz
75 Hz
60 Hz
70 Hz
75 Hz
60 Hz
60 Hz
60 Hz
60 Hz
VESA Standard
O
O
O
O
O
O
O
O
O
O
O
O
O
O
VGA and XGA are registered trademarks of International Business Machines Corp.
Information on the Software License for This Product
■ Software composition
The software included in this product is comprised of various software components whose individual copyrights
are held by SHARP or by third parties.
■ Software developed by SHARP and open source software
The copyrights for the software components and various relevant documents included with this product that were
developed or written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties,
and other relevant laws. This product also makes use of freely distributed software and software components
whose copyrights are held by third parties. These include software components covered by a GNU General Public
License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license agreement.
■ Obtaining source code
Some of the open source software licensors require the distributor to provide the source code with the executable
software components. GPL and LGPL include similar requirements. For information on obtaining the source code
for the open source software and for obtaining the GPL, LGPL, and other license agreement information, visit the
following website:
http://www.sharpusa.com/gpl
We are unable to answer any questions about the source code for the open source software. The source code for
the software components whose copyrights are held by SHARP is not distributed.
■ Acknowledgements
The following open source software components are included in this product:
• linux kernel/busybox/uClibc/zlib/libpng/libjpeg
CLEARING THE SECRET NUMBER
If you forget the secret number, clear the secret number using the following procedure.
1
Select an item from the list below to display the secret number input screen. (For operating the on-screen
display menu, see page 20.)
• “EZ Setup”, “CH Setup”, “Parental CTRL” or “Reset” on the Setup menu.
• “Color System” on the Option menu.
• “Software Update” on the Digital Setup menu.
2
Press and hold both CHr and VOLk on the TV simultaneously until the message appears on the screen.
The secret number is
.
• As a precautionary measure, make a note of your secret number above, cut it from this manual, and keep it in a safe place.
42
LC-52D85UN_E.indb 42
2009/03/19 17:30:09
Calling for Service
For location of the nearest Sharp Authorized Service, or to obtain product literature, accessories, supplies, or
customer assistance, please call 1-800-BE-SHARP.
LIMITED WARRANTY
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand Liquid Crystal Display product (the
“Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option,
either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the
purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product or if the serial number or model number affixed to the Product has
been removed, defaced, changed, altered or tampered with. This warranty does not cover installation or signal reception problems. This
limited warranty will not apply if the Product has been or is being used in a commercial setting or application; this warranty is meant solely
for the non-commercial, household use of the Product by consumers in their home or residence. If you intend to or already use this Product
for commercial purposes or in a commercial setting, there are warranties available to cover your use of this Product, the terms of which may
vary. Please contact 1-888-GO-SHARP for further information.
In order to enforce your rights under this limited warranty, you should follow the steps set forth below. You must be able to provide proof of
purchase to the servicer, which proof must include the date of purchase.
To the extent permitted by applicable state law, the warranties set forth are in lieu of, and exclusive of, all other warranties, express or
implied. Specifically ALL OTHER WARRANTIES OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED, ALL EXPRESS AND
IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE, AND FITNESS FOR A PARTICULAR
PURPOSE ARE SPECIFICALLY EXCLUDED. IF, UNDER APPLICABLE STATE LAW, IMPLIED WARRANTIES MAY NOT VALIDLY BE
DISCLAIMED OR EXCLUDED, THE DURATION OF SUCH IMPLIED WARRANTIES IS LIMITED TO THE PERIOD(S) FROM THE DATE OF
PURCHASE SET FORTH BELOW. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
The warranties given herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy
available to the purchaser and only for the time periods set forth herein. No other representations or promises made by anyone are
permitted. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all
liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims,
whether based on contract, negligence, strict liability or otherwise. Sharp does not warrant nor shall Sharp be liable, or in any way
responsible, for Products which have been subject to abuse (including, but not limited to, improper voltage), accident, misuse, negligence,
lack of reasonable care, alteration, modification, tampering, misuse, improper operation or maintenance or any damages or defects in the
Product which were caused by repairs or attempted repairs performed by anyone other than a Sharp authorized servicer. Nor shall Sharp
be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow limits on
warranties or on remedies for breach in certain transactions; in such states, the limits herein may not apply.
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND PUERTO RICO.
Model Specific Section
Your Product Model Number & Description:
LC-46D85UN/LC-52D85UN LCD Color Television
(Be sure to have this information available when you need service for your
Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
Additional Exclusions from
Warranty Coverage (if any):
In order for the Product to be serviced, the Product must be readily available
to the servicer, free and clear of any complex or non-standard installation,
mounting or other encumbrance which would unreasonably interfere with
servicing the Product. The Servicer will remount the Product after service,
provided that such remounting is not into a complex or non-standard installation. Any additional labor and materials required to remove and/or reinstall a
Product above and beyond the foregoing are not covered by this warranty,
may result in additional charges and are the responsibility of the consumer.
Image Retention resulting from a fixed image being displayed for long
periods of time is not covered by this Limited Warranty (see Operation
Manual on how to prevent this).
Where to Obtain Service:
From a Sharp Authorized Servicer located in the United States. To find the
location of the nearest Sharp Authorized Servicer, please call Sharp toll free
at 1-800-BE-SHARP.
What to do to Obtain Service:
Contact your Sharp Authorized Servicer to obtain in home service for this
product. The Servicer will come to your location and if necessary remove the
unit for repair at the Servicer’s facility and return the set to you once
completed. Be sure to have Proof of Purchase available.
TO OBTAIN PRODUCT INFORMATION OR PURCHASE ACCESSORIES AND EXTENDED WARRANTIES, CALL 1-800-BE-SHARP
OR VISIT www.sharpusa.com
43
LC-46_52D85UN_E_06.indd 43
2009/04/10 16:45:36
Dimensional Drawings
Unit: inch (mm)
LC-46D85UN
43 53/64 (1113)
16 25/32 (426)
22 43/64
(575.6)
29 45/64 (754)
21 21/32 (550)
4 47/64
(120)
15 3/4 (400)
3 29/32
(99)
15 3/4 (400)
6 3/4
(174.3)
1 63/64
(50)
27 47/64 (704)
40 19/64 (1023.4)
12 61/64
(329)
LC-52D85UN
49 19/64 (1252)
18 43/64 (474)
25 41/64
(651)
31 11/32 (796)
15 3/4 (400)
21 21/32 (550)
4 27/32
(123)
3 25/32
(96)
15 3/4 (400)
5 23/32
(145)
2 1/16
(52)
33 25/64 (848)
45 9/16 (1157)
12 61/64
(329)
LC-46_52D85UN_E_Hyo1-4.indd 2
2009/04/17 15:57:38
ENGLISH
LC-46D85UN
FRANÇAIS
LC-52D85UN
OPERATION MANUAL
MODE D'EMPLOI
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
ESPAÑOL
LC-46D85UN
LC-52D85UN
LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR ACL
TELEVISOR CON PANTALLA
DE CRISTAL LÍQUIDO
OPERATION MANUAL
MODE D'EMPLOI
MANUAL DE OPERACIÓN
SHARP CORPORATION
MANUAL DE OPERACIÓN
Printed in Mexico
Imprimé au Mexique
Impreso en México
TINS-E228WJZZ
09P06-MX-NM
LC-46_52D85UN_E_Hyo1-4.indd 1
IMPORTANT : Please read this operation manual before starting operating the equipment.
IMPORTANT : Veuillez lire ce mode d'emploi avant de commencer à utiliser l'appareil.
IMPORTANTE : Lea este manual de operación antes de comenzar a operar el equipo.
2009/04/10 15:45:29