- Computers & electronics
- Computer components
- Chassis components
- Computer cases
- SilverStone
- SST-ML01B-R
- Installation Guide
Silverstone ML01S-R Installation guide
Add to my manuals8 Pages
SilverStone ML01S-R is a compact and versatile computer case designed to accommodate Micro ATX motherboards and various storage devices. It features a stylish black and silver design with an aluminum front panel and a 0.8mm SECC body, ensuring durability and a sleek appearance. The case comes equipped with a TFX 300W PFC power supply, providing sufficient power for basic system configurations. It also includes a front I/O panel with USB 2.0, IEEE1394 (FireWire), audio, and microphone ports, offering easy access to peripherals and external devices.
advertisement
ML01
Milo Series
MANUAL
Product Overview
ML01
Specification:
Color: Black & Silver
Model: ML01B( Black ) , ML01S(Silver)
ML01B-R(Black, card reader) , ML01S-R(Silver, card reader)
Motherboard: Micro ATX
Drive Bay: External - 5.25" x 1
External - 3.5" x 1
Internal - 3.5" x 1
Cooling System: Front - 80 x 15mm intake, 1800rpm, 19CFM, 20.65dBA
Left side - Dedicated CPU vent
Top side - Oversized mesh grille over CPU area
Expansion Slot: 4 x low profile
Front I/O Port: USB2.0 x 1, IEEE1394 x 1, audio x 1, MIC x 1
Card reader format (ML01R only): MMC, SD, MD, CF, MS, SM, XD, MS PRO,
MS PRO DUO, MS DUO, MINI SD, RS MMC
Power Supply: TFX 300W PFC
Net Weight: 5 kg
Dimension: 330mm (W) x 98mm (H) x 423mm (D)
Disassemble Chart
TOP PANEL
MICRO ATX M/B
HDD
TFX 300W PFC POWER SUPPLY
BOTTOM PANEL
5.25 BAY*1
3.5 BAY*1
RESET SW
POWER SW
8015 FAN
FRONT IO(1394+AUDIO+USB)
LEFT PANEL
1
Use a screw driver to loosen two #6-32*6 screws on back side of the top panel.
2
Remove the top panel.
3
Lift the two latch hooks to remove the front panel.
4
Use the eight pieces of #6-32*4 screws in the accessory packet, screw the mother board on to the case as pictured.
Installation Guide
5
Take out two pieces of M3*4 screws, and secure the external 3.5"device as pictured.
6
Take out the external 3.5"drive bay cover from the front panel.
7 8
Plastic thumb screw
From the accessory packet, take out two pieces of M3*4 screws and screw the optical drive into place as pictured.
If optical drive cover on the front panel touches the optical drive and prevents the front panel from installing properly, use pre-drilled hole B to secure the optical drive instead, then use of a rubber filler is then required as pictured.
Take out a thumb screw from the accessory packet and secure the optical drive into place as pictured.
Installation Guide
9 Rubber padding placement
Rubber padding
Take out the rubber padding and stick it right behind the optical drive buttons on the front panel.
10 11
Take out the three special hard-drive screws provided in accessory packet (refer to photo), tighten those screws into Hard Disk Drive as pictured.
12
Place the Hard Disk Drive into the case according to the picture.
Take out one piece of M3*6 screw, use a screw driver to secure Hard Disk Drive into place as pictured.
Installation Guide
13
Place front panel back on the case and make sure it snaps into the latch hooks.
14
Put the top panel back on the case as pictured.
15
Make sure the top panel is securely fastened.
16
Installation complete!
Warranty Information
June , 2006
NO:G11400284
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project