Mitsubishi Electric XD200U data projector

ENGLISH
X D200
SD200
MODEL
XD200U / SD200U
EN – 1
ESPAÑOL
ITALIANO
DEUTSCH
FRANÇAIS
DATA
Projector
User Manual
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If you
use another power-supply cord, it may cause interference with radio and television reception.
Use the attached PS/2 adapter cable, USB adapter
cable and RGB cable with this equipment so as to
keep interference within the limit of a FCC Class B
device.
This apparatus must be grounded.
DO NOT LOOK DIRECTLY INTO THE LENS
WHEN PROJECTOR IS IN THE POWER ON
MODE.
When using the projector in Europe
COMPLIANCE NOTICE
This Projector complies with the requirements of the
EC Directive 89/336/EEC “EMC Directive” and 73/23/
EEC “Low Voltage Directive” as amended by Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen
at a level that gains proper operation in residential
areas, on business and light industrial premises and
on small-scale enterprises, inside as well as outside
of the buildings. All places of operation are
characterised by their connection to the public low
voltage power supply system.
WARNING
Use the attached PS/2 adapter cable, USB adapter
cable and RGB cable with this equipment so as to
keep interference within the limit of a EN55022
Class B. Please follow WARNINGS instructions.
EN – 2
ENGLISH
Contents
Important safeguards ...........................................................................4
Overview ............................................................................................... 6
Using the remote control ......................................................................8
Battery installation ......................................................................................................... 8
Installation ............................................................................................9
Basic connections ............................................................................... 10
Projector + AV equipment ............................................................................................. 10
Projector + DVD player or HDTV decoder ................................................................... 10
Projector + personal computer ...................................................................................... 11
Preparing the projector for operation ...............................................
To operate projector power ON..........................................................
Menu operation ..................................................................................
Picture adjustment .............................................................................
Advanced features for presentation ..................................................
12
13
15
18
20
Expand ........................................................................................................................... 20
PinP ................................................................................................................................ 20
Still ................................................................................................................................. 20
Mouse remote control .................................................................................................... 21
Lamp replacement .............................................................................
Indicators ............................................................................................
Maintenance .......................................................................................
Troubleshooting ..................................................................................
Specifications ......................................................................................
22
23
23
24
25
Connectors ..................................................................................................................... 26
Dimensional drawings .................................................................................................. 26
What’s included in the box ............................................................................................ 26
Replacement part .......................................................................................................... 26
Specification of RGB signals in each computer mode of the projector ....................... 27
Trademark, Registered trademark
Windows 98 and Windows 95 are registered trademarks of Microsoft in the U.S. and other countries.
Macintosh is registered trademark of Apple Computer Inc.
PS/2 is trademark or registered trademarks of International Business Machines Corporation.
DLP, Digital Micromirror Device and DMD are all trademarks of Texas Instruments.
DCDi is a trademark of Faroudja, a division of Sage,Inc.
MicroSaver and Kensington are registered trademarks of Kensington Technology Group.
Other brand or product names are trademarks or registered trademarks of their respective holders.
EN – 3
Important safeguards
Please read all these instructions regarding your projector and retain them for future reference. Follow all
warnings and instructions marked on the projector.
1.
Read instructions
All the safety and operating instructions should
be read before the appliance is operated.
10.
Power sources
This projector should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power,
please consult your appliance dealer or local
power company.
11.
Power-cord protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles,
and points where they exit from the appliance. Do
not put the power cord under a carpet.
12.
Overloading
Do not overload wall outlets and extension cords
as this can result in a fire or electric shock.
13.
Objects and liquids
Never push objects of any kind through openings of this projector as they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind on the projector.
2.
Retain instructions
The safety and operating instructions should be
retained for future reference.
3.
Warnings
All warnings on the appliance and in the operating instructions should be adhered to.
4.
Instructions
All operating instructions must be followed.
5.
Cleaning
Unplug this projector from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a damp soft cloth for cleaning.
6.
Attachments and equipment
Never add any attachments and/or equipment
without the approval of the manufacturer as
such additions may result in the risk of fire, electric shock or other personal injury.
14.
Water and moisture
Do not use this projector near water or in contact with water.
Servicing
Do not attempt to service this projector yourself.
Refer all servicing to qualified service personnel.
15.
Damage requiring service
Unplug this projector from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
(a)
If the power-supply cord or plug is damaged.
(b)
If liquid has been spilled, or objects have
fallen into the projector.
(c)
If the projector does not operate normally
after you follow the operating instructions.
Adjust only those controls that are covered
by the operating instructions. An improper
adjustment of other controls may result
in damage and may often require extensive work by a qualified technician to restore the projector to its normal operation.
(d)
If the projector has been exposed to rain
or water.
(e)
If the projector has been dropped or the
cabinet has been damaged.
(f)
If the projector exhibits a distinct change
in performance - this indicates a need for
service.
16.
Replacement parts
When replacement parts are required, be sure
that the service technician has used replacement
parts specified by the manufacturer or parts
having the same characteristics as the original
part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
17.
Safety check
Upon completion of any service or repair to this
projector, ask the service technician to perform
safety checks determining that the projector is
in a safe operating condition.
7.
8.
Accessories
Do not place this projector on an unstable cart,
stand, tripod, bracket or table. Use only with a
cart, stand, tripod bracket, or table recommended
by the manufacturer or sold with the projector.
Any mounting of the appliance should follow the
manufacturer's instructions and should use a
mounting accessory recommended by the manufacturer.
An appliance and cart combination should be
moved with care. Quick stops, excessive force and
uneven surfaces may cause the appliance and
cart combination to overturn.
9.
Ventilation
Slots and openings in the cabinet are provided
for ventilation, ensuring reliable operation of the
projector and to protect it from overheating. Do
not block these openings or allow them to be
blocked by placing the projector on a bed, sofa,
rug, or bookcase. Ensure that there is adequate
ventilation and that the manufacturer's instructions have been adhered to.
EN – 4
Do not operate if smoke, strange noise or odor comes
out of your projector. It might cause fire or electric
shock. In this case, unplug immediately and contact
your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifically explained in the Owner's
Guide, do not attempt to service this product
yourself. Please contact your dealer when you want
to fix, adjust or inspect the projector.
Do not modify this equipment.
It can lead to fire or electric shock.
If you break or drop the cabinet.
Do not keep using this equipment if you break or
drop it. Unplug the projector and contact your dealer
for inspection. It may lead to fire if you keep using
the equipment.
Do not face the projector lens to the
sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven
surface.
Place the projection on a leveled and stable surface
only. Please do not place equipment on unstable
surfaces.
Do not look into the lens when it is operating. It may
hurt your eyes.
Never let children look into the lens when it is on.
Do not turn off the main power
abruptly or unplug the projector
during operation.
Do not touch Air outlet grille and
Bottom plate which becomes hot.
Do not touch them or put other equipment in front of
Air outlet grille. The heated Air outlet grille and
Bottom plate may cause injury or damage to other
equipment. Also, do not set the projector on the desk
which is easily affected by heat.
Do not look into the air outlet grille
when projector is operating.
Heat, dust etc. may blow out of it and hurt your eyes.
Place of installation
For safety’s sake, refrain from setting the projector at
any place subjected to high temperature and high
humidity. Please maintain an operating temperature,
humidity, and altitude as specified below.
• Operating temperature: between +41°F (+5°C)
and +95°F (+35°C)
• Operating humidity: between 30 and 90%
• Never put any heat-producing device under the
projector so that the projector does not overheat.
• Do not attach the projector to a place that is
unstable or subject to vibration.
• Do not install the projector near any equipment
that produces a strong magnetic field. Also refrain from installing near the projector any cable
carrying a large current.
• Place the projector on a solid, vibration free
surface: otherwise it may fall, causing serious
injury to a child or adult, and serious damage to
the product.
• Do not stand the projector: it may fall, causing
serious injury and damage to the projector.
• Slanting the projector more than ±10˚(right and
left) or ±15˚ (front and rear) may cause trouble or
explosion of the lamp.
• Do not place the projector near air-conditioning
unit or heater to avoid hot air to the exhaust and
ventilation hole of the projector.
It can lead to lamp breakage, fire, electric shock or
other trouble. It is best to wait for the fan to turn off
before turning main power off.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced Radio / TV technician for help.
Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian ICES-003.
EN – 5
ENGLISH
WARNING:
Unplug immediately if there is
something wrong with your projector.
Overview
10
9 8
1
11
7
2 3
1
2
3
4
6
4
5
5
6
7
8
9
10
11
12
13
Air inlet grille (Front)
Lens
Foot adjustment buttons
Kensington Security Lock Standard connector
Air inlet grille (Side)
Speaker
Control panel
Zoom ring
Focus ring
Remote control sensor (Front)
Remote control sensor (Rear)
Air outlet grille (Rear)
Terminal board
1
2
3
4
5
6
7
POWER button
VIDEO button
AUTO POSITION button
+ , – (KEYSTONE) button
COMPUTER button
STATUS indicator
POWER indicator
13
12
Control panel
7
6
5
POWER LAMP/TEMP
STATUS
KEYSTONE
COMPUTER
AUTO
POSITION
POWER
+
VIDEO
–
1
2
4
3
Terminal board
1
2
3
10
9 8
6
7
VIDEO 2
IN
VIDEO 1
IN
COMPUTER 1 IN
MOUSE /RS-232C
S-VIDEO
MAIN
AC IN
5
AUDIO OUT
VIDEO
COMPUTER
AUDIO IN
COMPUTER 2 / COMPONENT IN
COMPUTER OUT
AUDIO
Video / Audio input terminals
COMPUTER AUDIO IN terminal
COMPUTER 2 / COMPONENT IN terminal
(D-SUB mini 15P)
4 COMPUTER OUT terminal (D-SUB mini 15P)
5 MOUSE / RS-232C (Mini DIN 9P) terminal
6 AUDIO OUT terminal
7 COMPUTER 1 IN terminal (D-SUB mini 15P)
8 Power jack
9 Ground terminal
10 Main power
I : ON
O : OFF
1
EN – 6
2
3
4
3
1
2
3
ENGLISH
Bottom side
Rear adjustment feet
Lamp cover
Front adjustment feet
Caution:
Do not replace the lamp right after using the projector. The
lamp is very hot.
2
1
11
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Transmitter indicator
Power button
COMPUTER button
Mouse button
Right click button (For mouse)
MENU button
AUTO POSITION button
KEYSTONE button
+ , – (KEYSTONE/VOLUME) buttons
EXPAND button
PinP button
ENTER / STILL button
Mouse pointer / Direction buttons
LASER button
VIDEO button
MUTE (Audio/Video) button
Laser aperture
Left click button (For mouse)
10
•
When pressing Mouse button, it illuminates and
Direction buttons work as the mouse pointer. Press
the Mouse button or MENU button to set off. (Direction buttons work as Direction buttons.)
Pressing LASER button emits the laser beam about
1 minute. Release LASER button and press it again
if you wish to emits the laser beam.
Remote control
1
2
3
POWER
MUTE
COMPUTER
VIDEO
MOUSE
LASER
16
15
14
4
13
5
R-CLICK
6
7
8
MENU
ENTER/STILL
AUTO POSITION
PinP
KEYSTONE EXPAND
– KEYSTONE +
– VOLUME +
9
17
12
AVOID EXPOSURE -LASER
RADIATION IS EMITTED
FROM THIS APERTURE.
•
About laser beam
18
This remote control is class 2 (max. output 1 mW laser diode
640 - 660 nm) laser equipment.
Beam Divergence : 6m distance about 10mm x 10mm (±6mm)
CAUTION
LASER RADIATION
DO NOT STARE INTO BEAM
WAVE LENGTH : 640 - 660 nm
MAX OUTPUT : 1 mW
CLASS 2 LASER PRODUCT
IEC 60825-1:1993+A1:1997
CAUTION :
• Pressing the LASER button provided remote control emits
laser beam. Do not look into the beam light directly. Do not
point the laser beam at people. Looking the laser beam directly
may damage eyesight.
• Use of controls or adjustments or procedures other than those
specified herein may result in hazardous radiation exposure.
EN – 7
Using the remote control
Battery installation
Use two AAA size batteries.
1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the
arrow.
2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -).
• Load the batteries from - spring side, and make sure to set them tightly.
3. Replace the back cover.
1
2
3
Important:
• Do not combine a new battery with an old one.
• Load batteries in the correct position.
• Do not heat, take apart, or throw batteries into fire.
• Do not try to recharge batteries. Do not use rechargeable batteries.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes
in contact with your eyes, rinse them with water and then consult your doctor.
Operation area
The range for operation is about 10 m (33 feet) when the remote control points to the projector. The distance to
the screen back to the projector must be less than 6 m (20 feet). Depending on the type of screen, the effective
distance may be different.
20˚
20˚
15˚
15˚
30mm
80mm
30˚
30˚
20˚
20˚
Important:
Avoid direct sunlight or fluorescent light on the remote control sensor. Also keep the distance of more than 2 m
between the remote control sensor and fluorescent lamp or the remote control may not work correctly. The remote
control may become less effective near an inverter fluorescent lamp. In such a case, put the attached lightshielding seal on of the remote control sensors that is closer to the fluorescent lamp.
EN – 8
Installation
Height
Picture size can be set by changing the distance between the screen and the projector.
Front projection
To find the approximate distance between the projector and screen:
Width
Screen
Multiply the width of the screen
A
B
x 1.8 (min.) , Multiply the width of the
screen x 2.2 (max.).
Screen
• Refer to the chart for recommended
distances in maximum zoom and
A=B
minimum zoom.
H
the screen and
L (between
the head of the projector)
Screen
Diagonal size
(inch)
40 "
60 "
80 "
100 "
150 "
200 "
250 "
300 "
Height
(inch)
24 "
36 "
48 "
60 "
90 "
120 "
150 "
180 "
Width
(inch)
32 "
48 "
64 "
80 "
120 "
160 "
200 "
240 "
Distance from screen (L) / (approximate)
Maximum
Minimum
zoom (WIDE)
zoom (TELE)
(inch)
(m)
(m)
(inch)
52
1.3
1.6
64
78
2.0
2.4
95
104
2.6
3.2
127
130
3.3
4.0
159
194
4.9
6.0
238
259
6.6
8.1
318
234
8.2
10.1
397
389
9.9
12.1
476
Height projected
image (H)
(cm)
8.7
13.1
17.4
21.8
32.7
43.5
54.4
65.3
(inch)
3.4
5.1
6.9
8.6
12.9
17.1
21.4
25.7
• The above numbers are approximate, and may be slightly different from the actual measurements.
Front projection, ceiling mount
For ceiling mount, you need the ceiling mount kit.
Ask a specialist for installation. For more details,
consult your dealer.
• This warranty does not cover damage caused by
the use of any unrecommended ceiling mount kit
and the installation of the ceiling mount kit at an
improper location.
• For rear projection, set IMAGE REVERSE in the
INSTALLATION menu to MIRROR. See Page 16.
• When using the ceiling mount, set IMAGE REVERSE in the INSTALLATION menu to MIRROR INVERT. See Page 16.
• Projected images may appear darker when the
unit is used as a ceiling installation than when it
is used in the tabletop position. This does not
signify a product malfunction.
Caution:
• Placing the projector on a carpet reduces ventilation from the fan at the bottom and might cause
problems. Place a hard board or similar item
under the projector to facilitate ventilation of the
unit.
• Place the projector more than 50cm (20 in.) from
the wall to prevent blocking the intake, exhaust
slots andventilation of this projector because hot
air comes out of it.
• Do not use the projector under the following
circumstances, which may cause fire or electric
shock.
• in a dusty or humid place
• while the projector is lying sideways
• near a heater
• in a kitchen or oily, smoky or damp place
• in direct sunlight
• where the temperature is lower than +41°F
(+5°C) or higher than +95°F (+35°C)
Rear projection
Ask a specialist for installation. For more details,
consult your dealer.
Important:
• Do not put stress on the lens, as this may cause
damage.
SCREEN
SCREEN
EN – 9
ENGLISH
Orientation of the projector
Basic connections
This projector can be connected to equipment such as PC, VCRs, video cameras and DVD players.
Important:
• Make sure that your equipment is turned off before connection.
• Plug in firmly and unplug by holding the plug, not by pulling the AC power cord.
• If connected units are set too close to one another, the image may be affected.
• Refer to the user manual of each component for details of connections.
Projector + AV equipment
Important:
• Match the color of video and audio plugs on the AV cable with the connections.
• S-video signals take priority over video signals. If you input both S-video signals and normal video signals at
the same time, the normal video input automatically is inhibited.
Connect either one of these.
VIDEO 2
IN
VIDEO 1
IN
COMPUTER 1 IN
MOUSE /RS-232C
S-VIDEO
MAIN
AC IN
to S-VIDEO (1or2) IN
AUDIO OUT
VIDEO
COMPUTER
AUDIO IN
COMPUTER 2 / COMPONENT IN
COMPUTER OUT
to VIDEO (1or2) IN
to AUDIO (1or2) IN
AUDIO
to audio output
to video output
VCR etc.
to S-video output
• Speaker output is mono.
Projector + DVD player or HDTV decoder
In the case of a DVD player equipped with a COMPONENT VIDEO output (525i / 625i), connect the DVD player
with the COMPUTER 2 / COMPONENT IN connector.
DVD player or HDTV decoder
AUDIO cable
to AUDIO OUT
CB(PB) CR(PR)
Y
to AUDIO IN
BNC - RCA connector
(optional)
VIDEO 1
IN
VIDEO 2
IN
COMPUTER 1 IN
MOUSE /RS-232C
S-VIDEO
MAIN
AC IN
AUDIO OUT
VIDEO
COMPUTER
AUDIO IN
No connection
COMPUTER 2 / COMPONENT IN
COMPUTER OUT
AUDIO
G
B
R
HD/CS
Mini D-SUB 15 pin-BNC
conversion cable (optional)
VD
to COMPUTER 2 IN
• When a DVD player is connected with the COMPUTER 1 IN connector, the image may not be projected correctly.
• When a 525p signal is inputted, select YCBCR/ YPBPR for the COMPUTER INPUT in the SIGNAL menu.
• Y, PB, PR is an example of the terminal names for a HDTV decoder.
• The terminal name is different depending on the connected equipment.
• Use mini D-SUB 15 pin-BNC conversion cable for connection.
• Some DVD players may not project the image correctly.
• When connecting with HDTV equipment which has R, G, B output, select RGB for the COMPUTER INPUT in
the SIGNAL menu.
• A TV60 or TV50 signal corresponds to component video signal only. When the RGB signal with 5 line form is
inputted, the image will not be projected correctly.
EN – 10
ENGLISH
Projector + Personal computer
RGB cable for PC
to COMPUTER (1or2) IN
VIDEO 1
IN
VIDEO 2
IN
COMPUTER 1 IN
AC IN
computer
MOUSE /RS-232C
S-VIDEO
MAIN
AUDIO OUT
VIDEO
COMPUTER
AUDIO IN
COMPUTER 2 / COMPONENT IN
COMPUTER OUT
AUDIO
to AUDIO IN
to monitor port
to COMPUTER
OUT
AUDIO OUT
MONITOR OUTPUT
RGB cable for PC (option)
When outputting to both a
PC monitor and the projector.
to PC audio
output
Audio cable (option)
Important:
• When you use a long RGB cable instead of the cable provided, the picture quality may deteriorate.
• Connectors or analog RGB output adapters may be necessary depending on the PC connected to this projector.
Please contact your dealer.
• The audio input for this projector is a stereo pin jack. (Speaker output is mono.) Please check the available
cable for the audio input terminal of the PC. Some personal computer may not have the audio output terminal.
For using Macintosh
• A monitor output adapter is necessary for a Macintosh if it has no video port. Please contact your dealer.
• A MAC adapter for RGB cable may be necessary depending on the personal computer connected to this projector. Please contact your dealer.
About DDC™ (For COMPUTER 1 IN connector)
The projector complies with VESA™ DDC™ 1/2B (EDID) specification. If your computer provides DDC™ 1/2B (EDID)
function, setup will be done automatically. If your system is Windows® 98 or higher, your computer supported in
standard. If your system is Windows® 95 or lower, you must down load the driver from our Internet Home Page for use
this function. Please contact your dealer or Mitsubishi sales office for more details.
EN – 11
Preparing the projector for operation
Getting ready for projection
Adjusting the angle of projection
1. Connect the power cord provided to the projector.
2. Connect the power cord to the wall power outlet.
3. Remove the lens cap.
For the best result, project onto a flat screen with a 90
degree angle to the floor. If necessary, tilt the projector
by adjusting the adjustment feet on the bottom of the
projector.
Warning:
• Do not look directly into the lens when projector is
“ON”.
• The lens cap is for protecting the lens. If you leave
the power on with the cap on, the cap may be warped.
Please remove the lens cap when you turn the power
on.
• This projector is equipped with the power cords for
both U.S. and Europe. Use the appropriate power
cord for your country.
• A three-pin grounding type power plug is used with
the projector. Do not remove the grounding pin on
the power plug. If you are unable to insert the plug
into the outlet, contact your electrician to replace
your A/C outlet.
• The supplied power cord for U.S. is used for 120V
only. Never connect to any outlet or power supply
having a different voltage or frequency. If you
connect to the power supply having a different
voltage, please use the appropriate power cord.
• Use 100-240V AC 50/60Hz correct voltage otherwise it may lead to fire or electric shock.
• Do not place any objects on the power cord, and keep
the projector away from heat sources to avoid breaking the power cord. A broken power cord can cause
fire or electric shock.
• Do not revise or alter the power cord otherwise it
may cause fire or electric shock.
Contact your dealer if the cord is broken.
Caution:
• Plug in firmly and unplug by holding the plug, not
by pulling the cable out.
• Do not plug in or out with wet hands. It may cause
an electric shock.
EN – 12
Screen
Front adjustment feet
1. Lift the projector to an appropriate angle.
2. Press the foot adjustment buttons, and the front
adjustment feet will slide out to their appropriate
positions.
3. Release the foot adjustment buttons to fix the feet
in those positions.
4. Turn the feet for fine adjustment.
Foot adjustment
buttons
Front adjustment
feet
• The projection angle can be adjusted by turning
the rear adjustment feet.
After using the projector
5. Put the front adjustment feet back into the projector.
Important:
• When the screen or projector is not placed flatly,
the projected image becomes distorted to shape a
trapezoid. When the image shape isn’t corrected
even after adjusting the projector and the screen,
adjust the widths of the top and bottom of the
image to be equal by pressing the KEYSTONE +
or - button. When adjusting by the remote control,
press the KEYSTONE button to display the
“KEYSTONE CORRECTION” menu first, and
adjust the widths by pressing the + or - button.
• Screen on a flat wall with a 90˚ angle to the floor.
• Align projector to produce a full screen display as
illustrated on page 9.
• The distance from the projector to the screen must
be compatible with screen size chart on page 9.
Note the distance from the screen chart.
2•9
MUTE button
VIDEO 2
IN
VIDEO 1
IN
COMPUTER 1 IN
MOUSE /RS-232C
S-VIDEO
MAIN
AC IN
AUDIO OUT
VIDEO
COMPUTER
AUDIO IN
COMPUTER 2 / COMPONENT IN
COMPUTER OUT
AUDIO
3•7•8
4
POWER
MUTE
COMPUTER
VIDEO
MOUSE
LASER
AUTO POSITION button
R-CLICK
3•7•8
POWER LAMP/TEMP
STATUS
KEYSTONE
COMPUTER
AUTO
POSITION
POWER
VIDEO
+
4
–
1. Turn on the equipment connected to the projector.
2. Put the projector into standby mode by pressing the
main power switch. The POWER indicator lights up
red.
3. Turn the projector on by pressing the POWER button. The light source lamp starts warming up, eventually turning completely on.
• When the light source lamp does not light up,
wait until the STATUS indicator is turned off,
then press the POWER button again.
• If the main power switch to the unit is turned
off within two minutes of turning off the light
source lamp, power will not be applied to the
lamp for one minute when the next time the
main unit power switch is turned on. When
this happens, the STATUS indicator will blink
for one minute.
Condition
AUTO POSITION
button
MENU
ENTER / STILL
AUTO POSITION
PinP
KEYSTONE EXPAND
– KEYSTONE +
– VOLUME +
• The picture might not be of optimum performance
in extreme hot or cold conditions. (The projector is
not malfunctioning.)
4. Select the desired external input source by using
the COMPUTER or VIDEO button.
• The COMPUTER or VIDEO button does not work
when MENU is displayed. At this time, the prohibition mark ( ) appeares on the screen.
• The projector automatically selects the appropriate
signal format. The selected signal format is displayed on the screen.
• When selecting the COMPUTER input, the image
may flicker. Press the $ or % button to adjust the
image.
5. Adjust the image size with the zoom ring by
turning it.
6. Adjust the focus with the focus ring by turning it.
Indicator STATUS POWER
Stand-by
When light source lamp is on
Light source lamp held off temporarily
Green
-
Red
Green
Red
Important:
• A darkened image may be seen right after pressing
the POWER button due to warming up of this projector. While warming up, no other commands can
be accepted.
• After the power is turned on, the screen may flicker
before the lamp operation becomes stable. This is
due to the characteristics of the lamp, not a failure
of the lamp.
• When the STATUS indicator is blinking red, the
lamp should be replaced. Replace the lamp. See
pages 22 and 23
.
focus ring
far
near
tele
wide
zoom ring
EN – 13
ENGLISH
To operate projector power ON
To operate projector power ON (Continue)
Turning off the projector
7. Press the POWER button.
The message “POWER OFF? YES : PRESS AGAIN”
appears on the screen.
8. Press the POWER button within 10 seconds again.
• The light source lamp will be turned off.
• When the POWER button is not pressed within 10
seconds, the message will be disappeared.
• Pressing the POWER button second time will shut
off the light source lamp, but the exhaust fan continues to operate for 120 seconds to cool down the
light source lamp.
9. Turn off the main power switch. When turning off
the main switch, the POWER indicator turns off.
• In cases where the main power switch is accidentally turned off when either the intake/exhaust
fan or the power source lamp is in operation, allow
the unit to cool down for 10 minutes with the
power turned off. Repeat step 3 when turning on
the power source lamp. If the lamp does not turn
on immediately, repeat this step two or three
times. Replace the lamp if it should still fail to
turn on.
AUTO POSITION button
When the source is selected to COMPUTER and the
image is not in the right place, follow as shown below.
1. Set screen to the brightest display as possible
(e.g., full-screen display of the “Trash” window).
2. If the screen saver is running, turn off the screen saver.
3. Press the AUTO POSITION button.
• If the image is still not in the right place, adjust
the image position by using the SIGNAL menu.
The volume from the speaker
Press the VOLUME + or – button to change the volume
from the speaker.
The volume control bar will appear on the screen.
• The volume control bar will disappear about 4
seconds after releasing the volume buttons.
• The volume buttons do not work when MENU
selection bar or MENU is displayed.
• The volume from the AUDIO OUT jack is also
changed by pressing the VOLUME + or – button on
the remote control.
EN – 14
AV mute
Image and audio are temporarily erased with pressing the MUTE button. To restore the image and
audio to the normal mode, press the MUTE button
again.
• The audio from the AUDIO OUT jack is also muted
by pressing the MUTE button.
Caution:
• When you have finished using this equipment, wait
120 seconds for the exhaust fans to stop. Then turn
off the main switch and unplug the power cable from
the wall outlet, for safety purposes.
• After the lamp is turned off, the lamp cannot be
switched on again for 60 seconds as a precautionary measure. It will take another 60 seconds before
the STATUS indicator goes off. If you wish to turn
on the projector again, wait until the indicator is off
then press the POWER button.
• The exhaust fan rotates faster when the temperature around the projector rises.
• When the temperature around the projector becomes
too high, the sign “TEMP!!” blinks red on the screen.
If the temperature stays too high, the lamp will be
shut off automatically.
Menu operation
CONTRAST
BRIGHTNESS
sRGB
COLOR MATRIX *1
COLOR TEMP
TINT *2,*5
*5
COLOR
SHARPNESS *5
INSTALLATION
AUTO POWER ON
AUTO POWER OFF
SPLASH SCREEN
BACK COLOR
IMAGE REVERSE
FEATURE
MENU POSITION
EXPAND MODE
VIDEO MODE *5
CINEMA MODE *5,*6
VIDEO SIGNAL *5
LANGUAGE
± 20
± 20
ON, OFF
VIDEO
COMPUTER
USER
OFF
STANDARD
LOW
HIGH
USER
± 10
± 10
±5
HORIZ.POSITION
VERT.POSITION
TRACKING *4
FINE SYNC. *4
COMPUTER INPUT *4
ANAMORPHIC
*4
HOLD
UPPER LEFT, LOWER RIGHT
EXPAND, REAL
1-4
AUTO, OFF
AUTO, NTSC, PAL, SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60
, English, Español, Deutsch, Français, Italiano,
OK
0 - 999
*3
0 - 999
*3
0 - 9999
*3
0 - 31
RGB, YCBCR / YPBPR
ON, OFF
ON
OFF
USER
OK
* 1: The item can not be selected when the sRGB is set to ON.
* 2: The item can not be selected with certain signals.
* 3: Setting range is different with certain signals.
* 4: The item can not be selected when the source is selected
VIDEO or S-VIDEO.
* 5: The item can not be selected when the source is selected
to COMPUTER.
* 6: The item can not be selected when the VIDEO MODE is
not set to 1.
Basic operation
Several settings can be adjusted using Menu.
EXAMPLE: Auto power off time setting
1. Press the MENU button.
opt.
TV60
IMAGE
2. Press the $ or % button to select the INSTALLATION menu.
opt.
TV60
± 30
± 30
± 30
± 30
± 30
± 30
± 10
± 15
± 15
± 15
± 15
ON, OFF
OFF, 5, 10, 15, 30, 60 min
ON, OFF
BLUE, BLACK
OFF, MIRROR, INVERT, MIRROR INVERT
RESET ALL
SIGNAL
RED
YELLOW
GREEN
CYAN
BLUE
MAGENTA
SATURATION
CONTRAST R
CONTRAST B
BRIGHTNESS R
BRIGHTNESS B
ENGLISH
IMAGE
BEGIN
END
CLAMP POSITION *4
CLAMP WIDTH *4
VERT.SYNC
SHUTTER (U)
SHUTTER (L)
SHUTTER (LS)
SHUTTER (RS)
0 - 15
0 - 15
0 - 127
*3
0 - 63
*3
AUTO, OFF
0 - 20
0 - 20
0 - 20
0 - 20
4. Press the { or } button to select AUTO POWER
OFF.
AUTO POWER
ON
OFF
AUTO POWER
OFF
OFF
5. Press the $ or % button to adjust auto power off
time.
AUTO POWER
ON
OFF
AUTO POWER
OFF
30min
6. Exit the menu system by pressing the MENU button several times.
INSTALLATION
3. Press the ENTER button (or } button).
opt.
TV60
INSTALLATION
AUTO POWER
ON
OFF
AUTO POWER
OFF
OFF
• If the menu operation is not working, turn off the
main power, wait about 10 minutes, and turn on the
main power again.
• The settings with
mark, you should press the
ENTER button after selecting.
EN – 15
Menu operation (continued)
1 IMAGE
opt.
CONTRAST ........ Adjusts the picture contrast. The contrast becomes
TV60
higher as the number increases.
BRIGHTNESS .... Adjusts the image brightness. The image becomes IMAGE
0
CONTRAST
brighter as the number increases.
sRGB ................... Select ON to display an image emphasizing on the color
0
BRIGHTNESS
reproducibility.
• When sRGB is ON, COLOR MATRIX can’t be adsRGB
OFF
justed.
OFF
COLOR MATRIX
• When sRGB is ON, the image will become darker.
• When COLOR TEMP. is set to other than STANCOLOR TEMP
STANDARD
DARD while sRGB is ON, colors won’t be reproduced
TINT
0
as per the standard value of sRGB.
• Though sRGB can be ON while a signal is input from
0
COLOR
VIDEO-IN or S-VIDEO IN, reproduced colors won’t
SHARPNESS
0
be in accordance with the sRGB standard value. Use
sRGB to suit your color preference.
COLOR MATRIX ....... Adjusts the color balance in each color of the image. See page 18.
COLOR TEMP. ... Adjusts the color temperature. See page 18.
TINT .................... Adjusts the color balance of the image. The color balance of the image shifts green as the
number increases and shifts to purple as the number decreases. (Available only when
VIDEO is selected as the source.)
• TINT cannot be adjusted when a TV50 (PAL or SECAM) signal is being displayed.
COLOR ................ Adjusts the color intensity of the image. (Available only when VIDEO is selected as the
source.)
SHARPNESS ...... Adjusts the image sharpness. The image sharpness rises as the number increases.
2 INSTALLATION
AUTO POWER ON .... Select ON to boot up the projector automatically by
opt.
turning on an externally connected power switch such as
TV60
a breaker even when the main power switch of the
INSTALLATION
projector is off. Use this setting when the projector is
AUTO POWER
hanging from the ceiling.
OFF
ON
• The projector will be in the stand-by mode when the
AUTO POWER
OFF
OFF
lamp is off. Use the remote control to turn on the
SPLASH
lamp.
ON
SCREEN
AUTO POWER OFF .. Set the time elapsed before the projector enters into the
BACK COLOR
BLUE
stand-by mode when there is no signal present at the
IMAGE
selected source.
OFF
REVERSE
SPLASH SCREEN ..... Select ON to display the splash screen when the power is
turned ON.
BACK COLOR .... Select the color of the background to blue or black, this will be displayed when there is no
signal present at the selected source.
IMAGE REVERSE ..... Use to reverse or invert the projected image. Select MIRROR in rear projection. Select
MIRROR, INVERT in rear projection with the projector hanging from the ceiling.
ON
3 FEATURE
MENU POSITION ..... Use to select the position of the menu on the screen,
UPPER LEFT or LOWER RIGHT.
EXPAND MODE .. Select the mode for enlarging screen. See page 20.
VIDEO MODE .... Use to select the modes of the high quality line doubler.
Select 1 for the Cross Color Suppression mode. Select 2
for DCDi mode. Select 3 for normal high quality line
doubler mode. Select 4 for through mode.
• Though square-shaped noise may appear in the
projected image when 1 is selected, this is not failure.
If it is obtrusive, select other positions than 1.
• A playback signal on a deteriorated videotape or a
poor-quality signal may not be projected properly.
When projecting such a signal, change the setting of
the Video mode and check the projection quality.
EN – 16
Opt
TV60
FEATURE
MENU POSITION
A
A
?
UPPER LEFT
EXPAND MODE
EXPAND
VIDEO MODE
1
CINEMA MODE
AUTO
VIDEO SIGNAL
AUTO
A Ë LANGUAGE
RESET ALL
English
OK
4 SIGNAL
HORIZ. POSITION .... Use to adjust the horizontal position of the image.
VERT. POSITION ..... Use to adjust the vertical position of the image.
TRACKING ......... Use to avoid image noise such as wide stripes.
FINE SYNC. ....... Use to synchronize the projector with PC input signals
so that the image is not blurred.
COMPUTER INPUT ...... This will be set automatically to match the input signal
to component video (YCBCR/YPBPR) or RGB. This can be
overridden as required.
ANAMORPHIC... Select ON when playing DVD discs containing data of
widescreen images.
HOLD .................. Adjusts the image when flagging occurs near the top of
the screen.
5 SIGNAL - USER (Normally, there is no need for adjustments.)
CLAMP POSITION/
CLAMP WIDTH ......... If you use something similar, the brighter colors of the
projected image may become blurred. In this case,
adjust CLAMP POSITION or CLAMP WIDTH.
VERT. SYNC ...... Use to adjust the image when its motion does not run
smoothly. Select AUTO for normal setting.
SHUTTER(U) ..... Use to adjust the image when the noise etc. appears on
top part of image.
SHUTTER(L) ...... Use to adjust the image when the noise etc. appears on
bottom part of image.
SHUTTER(LS) .... Use to adjust the image when the noise etc. appears on
left side of image.
SHUTTER(RS) ... Use to adjust the image when the noise etc. appears on
right side of image.
opt.
XGA60
SIGNAL
RRGGBB
HORIZ.POSITION
0
VERT.POSITION
0
TRACKING
0
FINE SYNC
0
COMPUTER
INPUT
RGB
ANAMORPHIC
OFF
HOLD
ON
USER
OK
opt.
XGA60
SIGNAL
SIGNAL - USER
CLAMP
CLAMP
POSITION
0
CLAMP
CLAMP WIDTH
0
?
VERT.SYNC
AUTO
SHUTTER (U)
0
SHUTTER (L)
0
SHUTTER (LS)
0
SHUTTER (RS)
0
EN – 17
ENGLISH
CINEMA MODE .. When ON is selected, the film mode will be automatically activated when a film source signal
is inputted. When OFF is selected, the film mode will not be activated.
VIDEO SIGNAL ... When AUTO is selected, the appropriate video format is automatically selected depending
on the input signal. If the image isn’t displayed correctly, select the desired video format
manually.
LANGUAGE ....... Use to select the language used in the menus. (
/ English / Español / Deutsch / Français
/ Italiano /
)
RESET ALL ........ Use to reset the MENU settings (except LANGUAGE).
Picture adjustment
Adjusting the image
You can adjust the picture by using the IMAGE menu.
opt.
TV60
5. Press the $ or % button to adjust the color balance
of the color.
IMAGE
CONTRAST
0
BRIGHTNESS
0
sRGB
OFF
COLOR MATRIX
OFF
COLOR TEMP
STANDARD
TINT
0
COLOR
0
SHARPNESS
0
4. Press the { or } button to select the desired color.
• If you wish to adjust the color intensity of the
image, select SATURATION.
6. Repeat steps 4 and 5 for more adjustments.
7. Exit the menu system by pressing the MENU button several times.
To control the level of white-to-black in the image :
Adjust CONTRAST in the IMAGE menu. Press the
% button to increase the contrast and the $ button
to reduce it.
To control the light level of the image :
Adjust BRIGHTNESS in the IMAGE menu. Press
the % button to lighten the image and the $ button
to darken the image.
• When using the setting which has been already
prepared, select desired position VIDEO or COMPUTER in step 2. When the source is selected to
VIDEO or S-VIDEO, VIDEO will be selected automatically. When the source is selected to COMPUTER, COMPUTER will be selected automatically.
• When not using Color matrix adjustment, select
OFF in step 2.
Color temperature
1. Select COLOR TEMP. in IMAGE menu.
2. Press the $ or % button to select USER .
3. Press the ENTER button.
COLOR TEMP.- USER
To adjust the red-green color balance of the image :
Adjust TINT in the IMAGE menu. Press the %
button to increase the amount of red in the image
and the $ button to increase the amount of green in
the image.
To determine the intensity of the color :
Adjust COLOR in the IMAGE menu. Press the %
button to increase the amount of color in the image
and the $ button to decrease it.
To adjust the detail and clarity of the image :
Adjust SHARPNESS in the IMAGE menu. Press the
% button to make the picture seem sharper and the
$ button to make it softer.
0
CONTRAST B
0
BRIGHTNESS R
0
BRIGHTNESS B
0
4. Press the { or } button to select the desired item.
5. Press the $ or % button to adjust the item.
6. Repeat steps 4 and 5 for more adjustments.
7. Exit the menu system by pressing the MENU button several times.
About color temperature
Color matrix
This feature adjusts the color balance of the primary
colors (red, green, blue), and secondary colors (yellow,
cyan, magenta). You can use the color matrix adjustment to emphasize a specific color without changing
the appearance of any of the other colors.
1. Select COLOR MATRIX in the IMAGE menu.
2. Press the $ or % button to select USER
3. Press the ENTER button.
COLOR MATRIX
EN – 18
CONTRAST R
RED
0
YELLOW
0
GREEN
0
CYAN
0
BLUE
0
MAGENTA
0
SATURATION
0
.
The appearance of white can be affected by adjusting the
color temperature. With low color temperature, white
appears reddish and with high color temperature white
appears to become more bluish. The color temperature
can be manually controlled by adjusting the red and
blue contrast level.
To set the color temperature high:
Set the contrast B (Blue) to a high number and the
contrast R(Red) to a low number.
To set the color temperature low:
Set the contrast B (Blue) to a low number and the
contrast R(Red) to a high number.
This projector should automatically display the full
computer image on the projection screen. However,
with some computers signals this may not occur, in
this case press the AUTO POSITION button. If the
images are still not projected correctly, use the
MENU display to adjust the projected images.
opt.
XGA60
SIGNAL
RRGGBB
Top part of image curves :
Change the setting of HOLD in the SIGNAL menu.
Select ON , press the ENTER buttun and adjust
BEGIN or END for image which top part is the least
curved.
Image does not move naturally :
Adjust VERT. SYNC of the menu in the SIGNAL USER menu. Select AUTO for normal setting.
• Do not change any other items in the SIGNAL USER menu for normal operation.
HORIZ.POSITION
0
VERT.POSITION
0
TRACKING
0
FINE SYNC
0
COMPUTER
INPUT
RGB
3. Select TRACKING in SIGNAL menu.
ANAMORPHIC
OFF
Simple adjustment method
1. Select HORIZ. POSITION in SIGNAL menu.
2. Press the$ or % button to adjust the horizontal
start position (the left side of image).
HOLD
ON
4. Press the$ or % button to adjust the horizontal
end position (the right side of image).
USER
OK
5. Repeat steps 1 to 4 for fine adjustment.
Image moved to right or left :
Adjust HORIZ. POSITION in the SIGNAL menu.
Press the % button to move the image to left. Press
the $ button to move the image to right.
6. Select VERT. POSITION in SIGNAL menu.
7. Press the$ or % button to adjust the vertical
start position (the top end of image).
Image moved to up or down :
Adjust VERT. POSITION in the SIGNAL menu.
Press the % button to move the image to upward.
Press the $ button to move the image to down.
Image flickers / Image is slightly blurred :
Adjust FINE SYNC. in the SIGNAL menu.
opt.
XGA60
SIGNAL
SIGNAL - USER
CLAMP
CLAMP
POSITION
0
CLAMP
CLAMP WIDTH
0
?
VERT.SYNC
AUTO
SHUTTER (U)
0
SHUTTER (L)
0
SHUTTER (LS)
0
SHUTTER (RS)
0
Wide stripes appear :
Adjust CLAMP POSITION or CLAMP WIDTH in
the SIGNAL - USER menu.
Noise appears on right or left side of image :
Adjust SHUTTER (LS), SHUTTER (RS) in the
SIGNAL - USER menu.
Noise etc. appears on top or bottom part of image :
Adjust SHUTTER (U), SHUTTER (L) in the SIGNAL - USER menu.
EN – 19
ENGLISH
Adjustment from personal computer
Advanced features for presentation
Expand
Picture in Picture (PinP)
By pressing the EXPAND button on the remote control, you can magnify the detailed image of the picture.
One of the special features of this unit is the picturein-picture (PinP) mode. PinP allows you to view different sources at the same time.
Using the Expand mode
1. Press the EXPAND button.
• You can magnify different areas of the active picture by pressing the {, }, $, % button.
• You can change the magnification of the zoomed area
by pressing the + or - button.
2. Press the EXPAND button on the remote control
again.
The normal screen display will appear on the screen.
• Display enlargement does not work with
video input or S-video input.
• The EXPAND mode will not work with certain signals.
Using the PinP mode
1. Press the PinP button on the remote control.
When the image from the COMPUTER IN terminal is displayed on the screen, the image from
VIDEO IN or S-VIDEO IN terminal is displayed as
sub-image.
• You can change the input source of the sub image
by pressing the VIDEO button.
• When the COMPUTER button is pressed, the input
source of the main image will be changed and the
sub image will disappear.
• When the image from the VIDEO IN or S-VIDEO
IN terminal is displayed on the screen, the PinP will
not work.
• The PinP mode will not work with certain signals.
REAL screen display
You can view the screen displaying the picture as its
original size (native resolution display).
To change frame position
2. Press the $ or % buttons on the remote control.
Setting the Expand mode for REAL screen
display
1. Press the MENU button.
3. Press the PinP button on the remote control again.
The sub image will disappear.
2. Press the $ or % to select the Feature menu.
3. Press the ENTER button.
4. Press the { or } button to select Expand Mode.
5. Press the $ or % to set the EXPAND to REAL.
Expand Mode
(EXPAND )
Zooming
image
(REAL)
Native resolution
display
6. Press the MENU button twice to exit the menu system.
Viewing the REAL screen display
1. Press the EXPAND button.
2. Exit the REAL mode, by pressing the EXPAND button again.
The normal screen display will appear on the screen.
• Display enlargement does not work with
video input or S-video input.
• During REAL mode, Press the $ or % buttons
for fine adjustment.
• During REAL mode, the { and } buttons are
not working. At this time, the prohibition mark
( ) appeares on the screen.
• The expanding rate cannot be changed by pressing either the + or - button. They are working for
volume adjustment.
EN – 20
• In PinP mode, the audio of the Main image is
output.
• In PinP mode, if the signal of the Main image is
lost, the sub image will disappear.
Still
How to stop the picture temporarily (still picture).
1. Press the STILL button on the remote control.
The picture will be freezed temporary.
To resume picture activity.
2. Press the STILL button on the remote control
again.
By connecting to personal computer through the USB or PS/2 port, you can operate your computer with the
projector remote control.
Connection
Projector + PC through USB connector
VIDEO 1
IN
VIDEO 2
IN
COMPUTER 1 IN
MOUSE /RS-232C
S-VIDEO
MAIN
AC IN
AUDIO OUT
VIDEO
COMPUTER
AUDIO IN
COMPUTER 2 / COMPONENT IN
COMPUTER OUT
AUDIO
to USB port
USB adapter cable
to MOUSE / RS-232C terminal
Mini DIN 9P
USB 4P (type A)
• Only PCs that support a USB mouse can be operated in this way. If your system is Windows® 98 or higher,
your computer will support USB as standard. If your system is Windows ® 95 or lower, please contact your
dealer. If your computer is Macintosh with USB port, you can use this function.
• When the lamp is turned ON, the computer connected with the USB cable may not work correctly. In this
case, restart the projector and the computer. If possible, you should connect the USB cable after the lamp is
turned ON.
Projector + PC through PS/2 connector
VIDEO 1
IN
VIDEO 2
IN
COMPUTER 1 IN
MOUSE /RS-232C
S-VIDEO
MAIN
AC IN
AUDIO OUT
VIDEO
COMPUTER
AUDIO IN
COMPUTER 2 / COMPONENT IN
COMPUTER OUT
AUDIO
PS/2 adapter cable
to mouse
(PS/2) port
to MOUSE / RS-232C terminal
Mini DIN 9P
Mini DIN 6P
• Turn off the PC and the projector before connecting to the PCs PS/2 port. If you connect the PS/2 cable when
the personal computer is on, the remote control mouse may not work. In that case, turn the projec-tor on, then
restart the personal computer.
• When you use an extension cable, the function may not work correctly.
Operation
Mouse
POWER
MUTE
COMPUTER
VIDEO
MOUSE
LASER
When pressing this button, it
illuminates. Mouse pointer/ direction
button operates as mouse pointer.
Mouse pointer
Use to move the cursor on the image,
instead of the computer mouse.
Left click
Right click
This operates in the same way as
the left button on the computer.
This operates in the same way as the
right button on the computer mouse.
R-CLICK
• When L/R click buttons and the mouse button are not used for 6 seconds, the mode will be changed to the
normal mode automatically.
EN – 21
ENGLISH
Mouse remote control
Lamp replacement
When the lamp no longer functions, replace it with a
new one.
Caution:
• Do not remove the lamp immediately after turning off the projector, the high temperature of the
lamp can burn you.
• For lamp replacement, press the power button to
power off, then wait for 120 seconds in stand-by
mode to allow the lamp to cool. Then turn off the
main switch, unplug the power cord from the
outlet, and wait one hour so that the lamp is
cooled to the touch.
• Do not remove the lamp except for replacement.
Careless treatment can cause injury or fire.
• Do not touch the lamp element directly. It may
break and cause you to injure or burn yourself.
• Be sure not to drop the lamp lid screw into the
projector. Also be sure not to insert metal or any
flammable objects, it may cause fire or electric
shock. If any objects are inserted, please unplug
and contact your dealer.
• Install the lamp securely, failure may cause a fire.
• If the light bulb part breaks, some small glass
fragments may fall out through the small cooling
grille, and stick to the inside of projector or the
lamp box. When taking the lamp out, make sure to
turn over the projector and hold the handle of the
lamp box to avoid injury from the glass fragments.
• Never shake the lamp or hold it in front of your face
after removingthe lamp box. The glass fragments
may fall out and cause injuries to your eyes and so
on.
1. Gently turn the projector over.
2. Loosen the screws of the lamp
lid (a) using a phillips screwdriver (+), and remove the lid.
• Remove the lamp cover in the
direction of the arrow as
indicated.
5. Hold onto the projector by the
handle as you pull out the
lamp.
• Pull out the lamp straight
upward.
• Pull the lamp out of the
projector slowly. Should the
light bulb be broken, glass
fragments will spill out if the
lamp is pulled out too quickly.
• Once the lamp has been
removed, do not spill liquid on
it, place it near flammable
objects or where children can
touch it. Otherwise, it may
cause injury or fire.
6. Insert the new lamp securely
into the projector body in the
right direction.
EN – 22
(b)
Handle
8. Tighten up the screws (b) using
a phillips screwdriver (+).
9. Tighten up the screws of the
lamp lid (a) using a phillips
screwdriver (+).
(a)
How to reset the operation time meter
Plug in the power cord, turn on the main power
switch, and reset lamp time by pressing the AUTO
POSITION button and POWER button for 3 seconds
simultaneously.
• Make sure that the STATUS indicator flashed
twice and the operation time meter has been
reset.
Caution:
• Do not spill liquid on the lamp or place it near
flammable objects or where children can touch it.
Otherwise, it could cause injury or fire.
• Be sure that the projector guide is firmly inserted
between the right and left lamp guides.
Important:
• The projector will not turn on if you do not secure
the lamp lid.
• You must reset the operation time meter after
you replace the lamp.
• Do not reset the operation time meter unless the
lamp has been replaced.
Interval of the lamp replacement
(a)
3. Loosen screws (b) using a
phillips screwdriver (+).
4. Pull up the handle.
7. Put the handle back to the
holding point.
• Make sure that the handle is
locked.
(b)
Handle
The expected lamp lifetime is about 1,500 hours of
operation. However, the lamp life may differ according to the operat-ing environment and may be
shorter than 1,500 hours. Decreases in brightness
will indicate that the projector lamp needs to be
replaced. When lamp operation time exceeds 1,000
hours, the indicator will flash alternately between green
and red (while the lamp is in operation; when the lamp is
not in operation, the STATUS indicator will appear red
only). When the lamp has been used for about 1,400
hours, the message “LAMP!!.” will appear on the screen for
one minute everytime the power is turned on. When the
lamp has been used for about 1,500 hours, the projector
will automatically shut off for safety and the power and
STATUS indicators light will be red. The projector cannot
be used until the lamp has been replaced and operation
timer has been reset.
Caution:
• The lamp is fragile. If broken, be careful not to cut
yourself with glass fragments.
• The replacement span of the lamp depends on the
environment. For replacement lamps, please contact
your dealer.
The projector automatically shuts off when the
lamp life exceeds 1,500 hours and cannot be
used until the lamp is replaced and the internal
timer is reset.
Indicators
The projector has two LED Indicators which show the
working condition of the projector.
The below table offers solutions to possible problems.
If a problem persists, turn the projector off and consult
your dealer.
STATUS indicator
POWER LAMP/TEMP
STATUS
COMPUTER
AUTO
POSITION
POWER
VIDEO
KEYSTON
+
–
Normal condition
Power
STATUS
Steady
red
Off
Steady
green
Blinking
green
Steady
green
Steady
green
CONDITION
Notes
Stand-by
Lamp stand-by (about for 1 minute)
The power button cannot be used to switch
ON and OFF
The POWER is ON. (Normal condition)
Abnormal condition
Power
STATUS
CONDITION
POSSIBLE SOLUTIONS
Unusual temperature
Steady
green
Blinking
orange
• The ventilation slits or air filter is clogged with
dust or debris.
• The room temperature is too high.
• The filter is dirty.
• Remove the object from the ventilation
slits.
• Relocate the projector to a cooler place.
• Clean the filter.
The protection circuit is working or the lamp is in an
abnormal condition.
• Wait until the STATUS indicator is
turned off, then press the POWER button.
• If the above operation is not effective,
replace the lamp.
Replace the lamp.
Exchange with a new lamp if the same
problem recurs.
Steady
red
Steady
red
Blinking
green
Steady
green
Blinking
green/red
Lamp duration warning. (Lightning duration total
about 1, 000 hours.When the POWER is ON.)
Steady
red
Blinking
red
Lamp duration warning. (Lightning duration total
about 1, 000 hours.When the POWER is OFF.)
Steady
red
Steady
red
Lamp duration warning. (Lightning duration total
about 1,500 hours.)
Blinking
green/red
Off
The lamp cover is not closed.
Close the cover correctly.
Abnormal.
Contact your dealer.
Steady
or
Blinking
green/red
Blinking
Maintenance
Caution:
Be sure to turn off the projector and unplug the power
cord from the wall outlet before you perform any maintenance on the projector.
Cleaning the projector and the ventilation
grille
Use a soft cloth to clean the projector and the ventilation grille. When the grille become dirty, wipe them with
a soft cloth dampened with a diluted mild detergent,
and then wipe them with a dry cloth.
To protect the surface of the projector from fading or
deteriorating:
• Do not spray insecticide on or inside the projector.
• Do not use benzine or thinner to clean it.
• Do not let rubber or plastic materials come into
contact with the projector.
Cleaning the lens
Use a standard lens-cleaning brush or a piece of lens
tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only recommended, nonabrasive
lens-cleaning materials. Do not touch the lens with your
fingers.
EN – 23
ENGLISH
Power indicator
Troubleshooting
The following offers solutions to some of the common problems you may encounter. We suggest that you consult
this chart before contacting your dealer.
PROBLEMS
The power is off.
CAUSE
• The air inlet grille, outlet grille or air filter is
clogged with dust or some other obstruction.
POWER indicator does not light up.
• Power cord is unplugged from the outlet.
• Power cord is disconnected from the projector.
• The main switch is turned off.
• The lamp lid is open.
Power indicator blinks red.
• The projector has been turned on again too soon
after having been turned off.
• When the power switch was turned off while
the fan was running, during or after lamp
operation.
• The room temperature is too high.
(Does the STATUS indicator show an unusual
condition?)
• Lamp is no longer working.
POWER indicator blinks between red and green.
• The lamp cover is not closed.
• When the STATUS indicator is on or blinking,
the main unit requires repairs.
No picture appears • Lens is covered by lens cap.
on the screen.
• When the STATUS indicator is on or blinking,
POSSIBLE SOLUTIONS
• Remove the obstruction.
•
•
•
•
Plug the power cord into the outlet.
Insert the power cord into the projector.
Turn the main switch on.
Close the lamp lid.
• Wait for the lighting sequence.
• Turn the power switch on and off several times.
• Refer to "Indicators" on page 23.
• Replace the lamp with a new one.
• Close the cover correctly.
• Contact your dealer.
• Take the lens cap off.
• Replace the lamp with a new one.
the main unit requires repairs.
• The equipment connected to this projector is not • Turn on the connected equipment.
turned on.
• Other equipment is not connected properly.
• Confirm the connections.
• The input source is not selected correctly.
• Select the correct source according to the equipment connected to this projector.
The image is
turned off.
• The air inlet grille, outlet grille or air filter is
clogged with dust or obstructed.
(In this case, the STATUS indicator does not light up.)
• Remove the obstruction and turn off the main
power switch. After about 10 minutes, turn the
projector on.
• The projector is not at a right angle to the screen.
The image is
• Adjust the angle of the projector to make a right
distorted.
angle to the screen. See page 12.
The image is dark. • Brightness, tint and color are not adjusted correctly. • Adjust brightness, tint and color correctly.
The image is
blurred.
• The projecting distance is beyond the focused area.
• Lens is dirty.
•
•
•
•
•
•
•
Screen size exceeds screen size specifications.
•
Brightness and contrast are not adjusted correctly. •
FINE adjustment is not made correctly.
•
Tracking is not adjusted.
•
The projector is not at a right angle to the screen. •
Adjust the projecting distance. See page 9.
Clean lens.
Use a screen size to within 40" to 300".
The image is distorted on the screen
and noise is heard.
• The cable for connection with other equipment
is not plugged securely into the terminal.
• The projector is installed too close to other
equipment.
Adjust brightness, contrast.
Make FINE adjustment.
Adjust tracking.
Adjust the angle of the projector to make a
right angle to the screen. See page 12.
• Plug the connecting cable securely into the
terminal. See pages 10-11.
• Increasethe distance between the projector
and other equipment.
No sound is heard.
• Volume is not turned up.
• Connection to other equipment is not made correctly.
• Turn up the volume.
• Check connections. See pages 10-11.
Nothing is displayed on
the PC monitor.
Warm air comes out of
the exhaust vents.
• The PC monitor is not turned on.
• Turn on the monitor.
• This is typical of the projector.
Adjustments cannot be • The operation is incorrectly made due to noise or • Turn off the main power, wait about 10 minmade.
interference.
utes, and turn on the main power again.
is displayed.
EN – 24
• This mark is displayed when an invalid operation is executed. This is not failure.
Specifications
DLP™ DATA projector
ENGLISH
Type
Model
Rated power supply
Rated input
Display Technology
Resolution
XD200U | SD200U
AC100V - 240V, 50 / 60Hz
2.8 A
0.7" Single chip Digital Micromirror Device (DMD) with R,G,B,W color wheel
1,024 × 768 (Total 786,432 pixels), 500 Video lines (XD200U)
800 × 600 (Total 480,000 pixels), 500 Video lines (SD200U)
Colors
Projection lens
Light source lamp
Picture size
PC compatibility
16,770,000 colors
F 2.5 - 3.0 f = 23.2 mm - 28.4 mm
210 W NSH
40 inch - 300 inch (aspect ratio 4:3)
Resolution : 640 x 400 - 1,024 x 768 + Compressed 1,280 x 1,024 (XD200U)
: 640 x400 - 800 x 600 + Compressed 1,024 x 768 (SD200U)
Sync on Green available
Video compatibility
NTSC / NTSC 4.43 / PAL (including PAL-M, N) / SECAM, PAL-60
DVD (Component) / HDTV (1080i) / 720p / (525p)
Audio output
Speaker
S-video input
2 W mono
Round type (8Ω 2W)
Luminance signal: Vp-p=1.0V 75Ω
(negative sync.)
Chroma signal: Vp-p=0.286V 75Ω (burst signal)
Video input
Audio inputs
Analog RGB input
(mini D-SUB 15P)
Vp-p=1.0V 75Ω (negative sync.)
350 mVrms, 10kΩ or more
RGB: Vp-p=0.7V 75Ω
YCBCR: Y: Vp-p=1.0V (negative sync.)
CBCR: Vp-p=0.7V
HD/CS : TTL level (positive or negative)
VD : TTL level (positive or negative)
Control connector
Outside dimensions
Serial (DIN 9 pin female connector) RS-232C standards
300 mm × 90 mm × 245 mm (11.8 inch × 3.5 inch × 9.6 inch)
(width × height × depth)
Weight
Length of power cord
Temperature, humidity
(performance guarantee)
Legs are not included.
Approx. 3kg
2.9 m ( 9.5 feet)
+41°F (+5°C) - +95°F (+35°C), 30 - 90%
Kensington Lock
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the Kensington System for instructions on how to use it to
secure the projector. Please contact to Kensington Technology Group as shown below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone : (650)572-2700
Fax : (650)572-9675
EN – 25
Specifications (continued)
Connectors
5
PC analog RGB input
Use to input video signals
(analog RGB) of a personal
computer.
RS-232C input
1
10
Use to control the projector with the
personal computer, or control the
personal computer with remote control.
Use the RS-232C cable (Mini DIN 9PD-SUB 9P) for the connection. For more
details, consult your dealer.
6
15
11
(Pin assignment of Mini D-SUB 15P jack)
PIN NO.
SPEC
PIN NO.
1
2
3
4
5
6
7
8
R(RED)/CR
G(GREEN)/Y
B(BLUE)/CB
GROUND
GROUND
GROUND
GROUND
GROUND
9
10
11
12
13
14
15
SPEC
1 23
7
4
89
PIN NO.
NAME
I/O
1
2
3
4
5
6
7
8
9
RXD
USB USB Vcc
GND
PS/2 Vcc
PS/2 CLK
TXD
PS/2 DATA
USB +
IN
OUT
IN
–
IN
OUT
OUT
OUT
OUT
–
GROUND
GROUND
DDC-DATA *1
HD/CS
VD
DDC-CLK *1
*1) For COMPUTER 1 IN
Dimensional drawings
(mm)
275
ø16
186
232
169
30
ø16
13
ø28
ø28
243.5
44.5
300
95
61
90
253
What’s included in the box
2 AC power cord
1
1
1
1
1
Video cable
S-Video cable
Audio cable
RGB cable for PC
PS/2 adapter cable
246C383-10
246C383-20
246C426-10
246C431-10
246C425-10
246C430-10
246C427-10
Replacement part
(Option / Not included in the box)
Spare Mercury lamp
EN – 26
499B029-10
(VLT-XD200LP)
1
1
1
1
1
2
1
USB adapter cable
Remote control
Light-shielding seal
User manual
Quick reference card
Battery for remote
Carrying case
246C428-10
939P892-10
620D070-10
871D349-10
857B057-10
–
772P037-10
Signal mode
TV60
TV50
525p
1080i
720p
PC98
CGA70
CGA84
CGA85
VGA60
VGA72
VGA75
VGA85
SVGA56
SVGA60
SVGA72
SVGA75
SVGA85
XGA43i
XGA60
XGA70
XGA75
XGA85
SXGA70a
SXGA75a
SXGA85a
SXGA60b
SXGA75b
SXGA43i
SXGA60
SXGA75
MAC13
MAC16
MAC19
MAC21
HP75
HP72
SUN66a
SUN76a
SUN66
SUN76
SGI72
SGI76
IBM60
resolution
(H x V)
–
–
–
–
–
640 x 400
640 x 400
640 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 864
1152 x 864
1280 x 960
1280 x 960
1280 x 1024
1280 x 1024
1280 x 1024
640 x 480
832 x 624
1024 x 768
1152 x 870
1024 x 768
1280 x 1024
1152 x 900
1152 x 900
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
horizontal
frequency (kHz)
15.73
15.63
31.47
33.75
45.00
24.82
31.47
37.86
37.86
31.47
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
35.52
48.36
56.48
60.02
68.68
63.85
67.50
77.49
60.00
75.00
46.43
63.98
79.98
35.00
49.72
60.24
68.59
62.94
78.13
61.85
71.81
71.68
81.13
76.92
82.00
63.42
• When the EXPAND MODE of FEATURE menu is
set to real screen display, by pressing the EXPAND button on the remote control, it will switch
to the screen displaying the picture as its original
size (real screen display). In the real screen
display, pictures will be black-framed when
picture resolution is lower than 1,024 x 768.
Important:
• Some computers may not be compatible with the
projector.
• The projector's maximum resolution is 1,024 x
768 pixels. It may not display correctly for the
pictures of higher resolutions than 1,024 x 768.
• The picture with a SYNC on G (Green) signal
may jitter.
• The picture with a SYNC on G (Green) signal
may be tinged with green.
Vertical
frequency (Hz)
59.94
50.00
59.94
60.00
60.00
56.42
70.09
84.14
85.08
59.94
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
86.96
60.00
70.07
75.03
85.00
70.01
75.00
85.06
60.00
75.00
86.87
60.02
75.03
66.67
74.55
75.02
74.96
74.92
72.00
66.00
76.63
66.68
76.11
72.30
76.00
60.00
Normal mode
(H x V)
1024 x 768
1024 x 768
1024 x 768
1024 x 576
1024 x 576
1024 x 640
1024 x 640
1024 x 640
1024 x 640
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
ENGLISH
Specification of RGB signals in each computer mode of the projector (For XD200U)
Real mode
(H x V)
–
–
–
–
–
640 x 400
640 x 400
640 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
640 x 480
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
• If the resolution and frequency of your computer
are not shown on the table, change the resolution
of your computer. You may find the compatible
resolution and frequency.
• Set the COMPUTER INPUT in SIGNAL menu to
RGB, when inputting the HDTV signal as RGB signal.
• When the COMPUTER INPUT in the SIGNAL
menu is set to RGB and a 525p signal is inputted,
the image will be projected in the VGA 60 format.
In this case, select YCBCR/ YPBPR for the
COMPUTER INPUT , and the format will be
changed to 525p automatically.
• A TV60 or TV50 signal corresponds to component
video signal only. When the RGB signal with 5
line form is inputted, the image will not be
projected correctly.
• When an unspecified signal is inputted, the
projector may not work correctly.
EN – 27
Specifications (continued)
Specification of RGB signals in each computer mode of the projector (For SD200U)
Signal mode
resolution
(H x V)
horizontal
frequency (kHz)
Vertical
frequency (Hz)
Normal mode
(H x V)
Real mode
(H x V)
TV60
–
15.73
59.94
800 x 600
–
TV50
–
15.63
50.00
800 x 600
–
525p
–
31.47
59.94
800 x 600
–
1080i
–
33.75
60.00
800 x 450
–
720p
–
45.00
60.00
800 x 450
–
PC98
640 x 400
24.82
56.42
800 x 500
640 x 400
CGA70
640 x 400
31.47
70.09
800 x 500
640 x 400
CGA84
640 x 400
37.86
84.14
800 x 500
640 x 400
CGA85
640 x 400
37.86
85.08
800 x 500
640 x 400
VGA60
640 x 480
31.47
59.94
800 x 600
640 x 480
VGA72
640 x 480
37.86
72.81
800 x 600
640 x 480
VGA75
640 x 480
37.50
75.00
800 x 600
640 x 480
VGA85
640 x 480
43.27
85.01
800 x 600
640 x 480
SVGA56
800 x 600
35.16
56.25
800 x 600
800 x 600
SVGA60
800 x 600
37.88
60.32
800 x 600
800 x 600
SVGA72
800 x 600
48.08
72.19
800 x 600
800 x 600
SVGA75
800 x 600
46.88
75.00
800 x 600
800 x 600
SVGA85
800 x 600
53.67
85.06
800 x 600
800 x 600
XGA43i
1024 x 768
35.52
86.96
800 x 600
800 x 600
XGA60
1024 x 768
48.36
60.00
800 x 600
800 x 600
XGA70
1024 x 768
56.48
70.07
800 x 600
800 x 600
XGA75
1024 x 768
60.02
75.03
800 x 600
800 x 600
XGA85
1024 x 768
68.68
85.00
800 x 600
800 x 600
MAC13
640 x 480
35.00
66.67
800 x 600
640 x 480
MAC16
832 x 624
49.72
74.55
800 x 600
800 x 600
MAC19
1024 x 768
60.24
75.02
800 x 600
800 x 600
MAC21
1152 x 870
68.59
74.96
800 x 600
800 x 600
HP75
1024 x 768
62.94
74.92
800 x 600
800 x 600
• When the EXPAND MODE of FEATURE menu is
set to real screen display, by pressing the EXPAND button on the remote control, it will switch
to the screen displaying the picture as its original
size (real screen display). In the real screen
display, pictures will be black-framed when
picture resolution is lower than 800 x 600.
Important:
• Some computers may not be compatible with the
projector.
• The projector's maximum resolution is 800 x 600
pixels. It may not display correctly for the pictures of higher resolutions than 800 x 600.
• The picture with a SYNC on G (Green) signal may
jitter.
• The picture with a SYNC on G (Green) signal may
be tinged with green.
• If the resolution and frequency of your computer
are not shown on the table, change the resolution
of your computer. You may find the compatible
resolution and frequency.
EN – 28
• Set the COMPUTER INPUT in SIGNAL menu to
RGB, when inputting the HDTV signal as RGB signal.
• When the COMPUTER INPUT in the SIGNAL
menu is set to RGB and a 525p signal is inputted,
the image will be projected in the VGA 60 format.
In this case, select YCBCR/ YPBPR for the COMPUTER INPUT, and the format will be changed
to 525p automatically.
• A TV60 or TV50 signal corresponds to component
video signal only. When the RGB signal with 5
line form is inputted, the image will not be projected correctly.
• When an unspecified signal is inputted, the
projector may not work correctly.
Manufactured by Mitsubishi Electric Corporation
1 Zusho Baba, Nagaokakyo-City, Kyoto Japan
871D349A10
Printed in Japan
DATA Projector
XD200U
SD200U
Control projector by using a personal computer
This projector can be controlled by connecting a personal computer with RS-232C terminal.
Functions can be controlled by a personal computer:
• Turn the ON or OFF
• Changing input signals
• Menu setting (for picture related setting only)
Connection
VIDEO 1
IN
VIDEO 2
IN
COMPUTER 1 IN
MOUSE /RS-232C
S-VIDEO
MAIN
AC IN
AUDIO OUT
VIDEO
COMPUTER
AUDIO IN
COMPUTER 2 / COMPONENT IN
COMPUTER OUT
AUDIO
to RS-232C terminal
to Com1
Comport
RS-232C cable
Mini DIN 9P
•
D-SUB 9P
This cable is a special cable. For
more details, consult your dealer.
Important:
• Make sure that your computer and projector are turned off before connection.
• Turn on the projector after the computer is started up.
(If you do not follow this order, the Comport may not function.)
• Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details.
1) Interface
PROTOCOL
RS-232C
BAUD RATE
9600 [bps]
DATA LENGTH
8 [bits]
PARITY BIT
STOP BIT
NONE
1 [bit]
FLOW CONTROL
NONE
12
6
3
1 RXD (IN: on the Projector side)
4 GND
7 TXD (OUT: on the Projector side)
7 9
This projector uses RXD, TXD and GND lines for RS-232C control.
For RS-232C cable,the reverse type cable should be used.
2) Control command diagram
The command is structured by the address code, function code, data code and end code. The length of the
command is different by each function.
HEX
Address code
30h 30h
Function code
Function
Data code
Data
'0' '0'
Function
Data
ASCII
[Address code]
[Function code]
[Data code]
[End code]
End code
0Dh
30h 30h (In ASCII code, '0' '0') fixed.
A code of each fixed control move.
A code of each fixed control data (number) and not always indicated.
0Dh (In ASCII code, ' ') fixed.
1
3) Control sequence
(1) Send the command from a personal computer to the projector. (The commands must be sent at least
400ms apart.)
(2) The projector will send a return command 400ms* after it has received an end code. If the command is
not received correctly, the projector will not send the return command.
(3) The personal computer checks the command and confirms if the command which has been sent has been
executed or not.
(4) This projector sends various codes other than the return code. When having a control sequence by RS232C, reject other codes from personal computer side.
•
•
The first character of the Status code from projector may not be displayed correctly. In this case, reject the
first character on the computer side.
* : The sending time of return command may delay depending on the condition (during changing the
input signal, etc.).
[Example] Turn the power ON (' 'is for ASCII code)
Sending commands
from the PC etc.
Status code from
projector
Meaning
30 30 21 0D
'0' '0' '!' ' '
Command for POWER ON
30 30 21 0D
'0' '0' '!' ' '
Command received
(Command echo back)
4) Operation commands
The operation commands execute the basic operation setting of this projector. It may not operate when changing the signal.
Operation
POWER ON
POWER OFF
INPUT COMPUTER 1
INPUT COMPUTER 2
INPUT VIDEO 1
INPUT VIDEO 2
ASCII
!
"
_r1
_r2
_v1
_v2
HEX
21h
22h
5Fh
5Fh
5Fh
5Fh
72h
72h
76h
76h
31h
32h
31h
32h
• POWER OFF command will not work for 1 minute after the power is turned on.
• POWER ON command will not work for 1 minute after the power is turned off.
[Example] Set the input signal to COMPUTER (' 'is for ASCII code)
Sending commands
from the PC etc.
Status code from
projector
Meaning
30 30 5F 72 31 0D
'0' '0' '_' 'r' '1' ' '
Command for setting the input
signal to COMPUTER
30 30 5F 72 31 0D
'0' '0' '_' 'r' '1' ' '
Command received
(Command echo back)
5) Volume commands
The volume commands execute the volume setting of this projector with the value.
ITEM
VOLUME
ASCII
VL
HEX
56h 4Ch
VALUE
00 - 31
How to set the grade
Use ASCII letters code to set the grade for setting data. Please refer to the table below for HEX code.
ASCII
HEX
'0'
30h
'1'
31h
'2'
32h
'3'
33h
'4'
34h
'5'
35h
'6'
36h
'7'
37h
'8'
38h
'9'
39h
[Example] Set the volume to 15 (Standard value) (' 'is for ASCII code)
Sending commands
from the PC etc.
30 30 56 4C 31 35 0D
'0' '0' 'V' 'L' '1' '5' '
Status code from
Meaning
projector
Command for setting the volume
'
30 30 56 4C 31 35 0D
Command received
'0' '0' 'V' 'L' '1' '5' '
(Command echo back)
'
2
6) Remote commands
Some remote control operations can be done by remote command codes.
Button's name on remote
KEYSTONE
+ (KEYSTONE/VOLUME)
– (KEYSTONE/VOLUME)
EXPAND
PinP
{
}
$
%
MENU
ENTER
AUTO POSITION
STILL
ASCII
r43
r06
r07
r02
r04
r53
r2b
r4f
r59
r54
r10
r09
ra4
HEX
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
34h
30h
30h
30h
30h
35h
32h
34h
35h
35h
31h
30h
61h
33h
36h
37h
32h
34h
33h
62h
66h
39h
34h
30h
39h
34h
[Example] Display MENU selection bar. (' 'is for ASCII code)
Sending commands
Status code from
from the PC etc.
30 30 72 35 34 0D
'0' '0' 'r' '5' '4' '
Meaning
projector
Command as same as MENU button
'
30 30 72 35 34 0D
Command received
'0' '0' 'r' '5' '4' '
(Command echo back)
'
7) Reading command diagram
Monitor projector operation status. The power ON, OFF and input terminal settings can be monitored.
POWER ON
POWER OFF
INPUT COMPUTER 1
INPUT COMPUTER 2
INPUT VIDEO 1
INPUT VIDEO 2
Function
vP
vP
vI
vI
vI
vI
ASCII
Data (Receive)
1
0
r1
r2
v1
v2
Function
76h 50h
76h 50h
76h 49h
76h 49h
76h 49h
76h 49h
HEX
Data (Receive)
31h
30h
72h 31h
72h 32h
76h 31h
76h 32h
When a personal computer sends the command, data code will not be attached. On the other hand, the projector
which has received a command will attach the recent operating status and then send.
[Example ] Input was Video 1 when the operating status of the input terminal was confirmed.
Sending commands
Status code from
from the PC etc.
30 30 76 49 0D
'0' '0' 'v' 'I' '
Meaning
projector
Command to confirm input
'
30 30 76 49 76 31 0D
Command (Input is Video 1)
'0' '0' 'v' 'I' 'v' '1' '
carrired out
'
8) Menu setting commands
The menu setting commands execute the menu setting of this projector. If the personal computer doesn’t send
the commands without attaching the data code, the projector which has received the command replays the
setting data as data code.
ITEM
CONTRAST
BRIGHTNESS
sRGB
COLOR MATRIX (MODE)
COLOR MATRIX (R, G, B)
COLOR MATRIX (Y, C, M)
COLOR MATRIX (SATURATION)
COLOR TEMP.
TINT
COLOR
SHARPNESS
LANGUAGE
ASCII
P
Q
SRGB
CMT
MRGB
MYCM
MSAT
A
S
T
R
LG
HEX
50h
51h
53h
43h
4Dh
4Dh
4Dh
41h
53h
54h
52h
4Ch
RESET ALL
MUTE
RSTALL
MUTE
52h 53h 54h 41h 4Ch 4Ch
4Dh 55h 54h 45h
0 (MUTE OFF), 1 (MUTE ON)
52h
4Dh
52h
59h
53h
47h
54h
47h
43h
41h
42h
42h
4Dh
54h
47h
3
VALUE
±20
±20
0 (OFF), 1 (ON)
1 (VIDEO), 2 (COMPUTER), 3 (USER), 4 (OFF)
±30±30±30 (R+G+B)
±30±30±30 (Y+C+M)
±10
1 (Standard), 2 (High), 3 (Low), 4 (User)
±10
±10
±05
0(
), 1 (English), 2 (Español), 3 (Deutsch) ,
4 (Frençais), 5 (Italiano), 6 (
)
How to set the grade
Use ASCII letters code to set the grade for setting data. Please refer to the table below for HEX code.
ASCII
HEX
'+'
2Bh
[Example 1]
'-'
2Dh
'0'
30h
'2'
32h
'3'
33h
'4'
34h
'5'
35h
'6'
36h
'7'
37h
'8'
38h
'9'
39h
Set the MUTE to ON.
Sending commands
from the PC etc.
30 30 4D 55 54 45 31 0D
'0' '0' 'M' 'U' 'T' 'E' '1' '
[Example 2]
Status code from
Meaning
projector
Command for setting the
'
30 30 4D 55 54 45 31 0D
MUTE to ON
Command received
'0' '0' 'M' 'U' 'T' 'E' '1' '
(Command echo back)
'
The TINT was set to +10 when the setting status was confirmed.
Sending commands
from the PC etc.
30 30 53 0D
'0' '0' 'S' '
'1'
31h
Status code from
Meaning
projector
Command to confirm
'
30 30 53 2B 31 30 0D
setting of TINT
Command (setting of TINT
'0' '0' 'S' '+' '1' '0' '
is +10) carried out
4
'