Registre seu produto e obtenha suporte em
www.philips.com/welcome
HTS7140
1
Important
Safety
Product care
Disposal of your old product and batteries
3D health warning
2
Your home theater
Main unit
Remote control
3
Connect your home theater
Connectors
Connect to the TV
Connect audio from TV or other devices
Connect to the Internet
4
Use your home theater
Before you start
Access the home menu
Choose your sound
Play a disc
Use Bonus View on Blu-ray
Access BD-Live on Blu-ray
Play 3D video
Play from a USB storage device
More play features for disc or USB
Browse Net TV
Play from radio
Play audio from TV or other devices
Play from an MP3 player
Play from an iPod or iPhone
Use Philips EasyLink
5
Change settings
Access the setup menu
Change video settings
Change audio settings
Set up network
Set up EasyLink
Change preference settings
Change advanced settings
2
2
2
3
3
4
4
4
Update software
Check software version
Update software from the network
Update software from a USB
Update electronic user manual
21
21
21
22
22
7
Product specications
23
8
Troubleshooting
24
9
Index
26
7
7
8
9
10
11
11
11
11
12
13
13
14
14
14
15
16
17
17
17
17
18
18
18
19
19
19
20
20
EN
1
Eng l i s h
6
Contents
1
Important
Read and understand all instructions before you
use your home theater. If damage is caused by
failure to follow instructions, the warranty does
not apply.
Safety
Risk of electric shock or re!
• Never expose the product and
accessories to rain or water. Never
place liquid containers, such as vases,
near the product. If liquids are spilt on
or into the product, disconnect it from
the power outlet immediately. Contact
Philips Consumer Care to have the
product checked before use.
• Never place the product and
accessories near naked flames or other
heat sources, including direct sunlight.
• Never insert objects into the
ventilation slots or other openings on
the product.
• Where the mains plug or an appliance
coupler is used as the disconnect
device, the disconnect device shall
remain readily operable.
• Disconnect the product from the
power outlet before lightning storms.
• When you disconnect the power cord,
always pull the plug, never the cable.
Risk of short circuit or re!
• Before you connect the product to the
power outlet, ensure that the power
voltage matches the value printed on
the back or bottom of the product.
Never connect the product to the
power outlet if the voltage is different.
Risk of injury or damage to the home theater!
• For wall-mountable products, use
only the supplied wall mount bracket.
Secure the wall mount to a wall that
can support the combined weight
of the product and the wall mount.
Koninklijke Philips Electronics N.V.
bears no responsibility for improper
wall mounting that results in accident,
injury or damage.
2
EN
•
For speakers with stands, use only the
supplied stands. Secure the stands
to the speakers tightly. Place the
assembled stands on flat, level surfaces
that can support the combined weight
of the speaker and stand.
• Never place the product or any objects
on power cords or on other electrical
equipment.
• If the product is transported in
temperatures below 5°C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
• Visible and invisible laser radiation
when open. Avoid exposure to beam.
• Do not touch the disc optical lens
inside the disc compartment.
Risk of overheating!
• Never install this product in a confined
space. Always leave a space of at least
four inches around the product for
ventilation. Ensure curtains or other
objects never cover the ventilation
slots on the product.
Risk of contamination!
• Do not mix batteries (old and new or
carbon and alkaline, etc.).
• Remove batteries if they are exhausted
or if the remote control is not to be
used for a long time.
• Batteries contain chemical substances,
they should be disposed of properly.
Product care
•
•
•
•
Do not insert any objects other than
discs into the disc compartment.
Do not insert warped or cracked discs
into the disc compartment.
Remove discs from the disc compartment
if you are not using the product for an
extended period of time.
Only use microfiber cloth to clean the
product.
Your product is designed and manufactured with
high quality materials and components, which can
be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC. Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and do not
dispose of your old products with your normal
household waste.
Correct disposal of your old product helps to
prevent potential negative consequences for the
environment and human health.
3D health warning
If you or your family has a history of epilepsy
or photosensitive seizures, consult a medical
professional before exposing yourself to flashing
light sources, rapid image sequences or 3D viewing.
To avoid discomfort such as dizziness, headache
or disorientation, we recommend not watching
3D for extended periods of time. If you
experience any discomfort, stop watching 3D
and do not immediately engage in any potentially
hazardous activity (for example driving a car)
until your symptoms have disappeared. If
symptoms persist, do not resume watching 3D
without consulting a medical professional first.
Parents should monitor their children during 3D
viewing and ensure they do not experience any
discomfort as mentioned above. Watching 3D is
not recommended for children under six years of
age as their visual system is not fully developed yet.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot be
disposed with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries because correct
disposal helps to prevent negative consequences
for the environmental and human health.
EN
3
Eng l i s h
Disposal of your old product
and batteries
2
Your home theater
Congratulations on your purchase, and welcome
to Philips! To fully benefit from the support that
Philips offers, register your home theater at www.
philips.com/welcome.
Main unit
Remote control
Note
• Your home theater is supplied with one of the
following remote controls.
Remote control - A
1
19
2
18
a
+/- ( Volume)
Increases or decreases volume.
b SOURCE
Selects a media to play or an audio input
source.
c
(Standby-On)
Switches on the home theater or switches
to standby mode.
d Playback buttons
5
17
(Eject)
Ejects the disc from the disc compartment.
6
16
15
Control playback.
e
3
4
7
8
9
10
14
f Display panel
g Disc compartment
11
13
4
EN
12
(Standby-On)
Switches the home theater on or to
standby.
• When EasyLink is enabled, press
and hold for at least three seconds
to switch all connected HDMI CEC
compliant devices to standby.
o
•
b
(Home)
Accesses the home menu.
c
SOUND SETTINGS
Accesses or exits various sound OPTIONS.
d Navigation buttons
• Navigates menus.
• In radio mode, press left or right to
start auto search.
e OK
• Confirms an entry or selection.
f
OPTIONS
• Accesses more play OPTIONS during
playback.
• In radio mode, programs radio stations.
(Stop) / (Eject / Open/Close)
Stops play.
Press and hold to eject the disc or
open the disc compartment.
• In radio mode, erases the current
preset radio station.
•
•
p
(Mute)
Mutes or restores volume.
q
BACK
Returns to a previous menu screen.
Eng l i s h
a
r POP-UP MENU/DISC MENU
Accesses or exits the disc menu.
s Source buttons
• Color buttons (for Blu-ray discs):
•
•
•
•
Selects tasks or OPTIONS.
DISC: Switches to disc source.
RADIO: Switches to FM radio.
DOCK for iPod: Switches to Philips
Dock for iPod/iPhone.
SOURCE : Selects an audio input
source.
g +/- ( Volume)
Increases or decreases volume.
h
(Play)
Starts or resumes play.
i
(Pause)
Pauses play.
j
/
(Fast Backward/Fast Forward)
Fast backwards or fast forwards. Press
repeatedly to change the search speed.
k Alphanumeric buttons
Enters values or letters (using SMS style
entry).
l SUBTITLE
Selects subtitle language for video.
m TOP MENU
Accesses the main menu of a video disc.
n
/
•
•
(Previous/Next)
Skips to the previous or next track,
chapter or file.
In radio mode, selects a preset radio
station.
EN
5
Remote control - B
b
(Home)
Accesses the home menu.
c
(Disc menu)
Accesses or exits the disc menu.
2
d Navigation buttons
• Navigates menus.
• In radio mode, press left or right to
3
e
1
start auto search.
4
5
/
•
•
5
6
18
7
8
9
f OK
Confirms an entry or selection.
g
h
(OPTIONS)
Accesses more play OPTIONS during
playback.
• In radio mode, programs radio stations.
10
11
i
12
j +/- ( Volume)
13
14
(Play)
Starts or resumes play.
Increases or decreases volume.
k
15
(Sound OPTIONS)
Accesses or exits various sound OPTIONS.
•
17
16
(Pause)
Pauses play.
l Source buttons / Color buttons
• Blu-ray discs: Selects tasks or OPTIONS.
• AUDIO SOURCE : Selects an audio
•
•
•
a
6
(Previous/Next)
Skips to the previous or next track,
chapter or file.
In radio mode, selects a preset radio
station.
input source.
DOCK for iPod: Switches to Philips
Dock for iPod/iPhone.
RADIO: Switches to FM radio.
DISC: Switches to disc source.
m Alphanumeric buttons
(Standby-On)
• Switches the home theater on or to
standby.
• When EasyLink is enabled, press
and hold for at least three seconds
to switch all connected HDMI CEC
compliant devices to standby.
EN
Enters values or letters (using SMS style entry).
n TOP MENU
Accesses the main menu of a video disc.
o SUBTITLE
Selects subtitle language for video.
(Stop)
Stops play.
Press and hold to eject the disc or
open the disc compartment.
• In radio mode, erases the current
preset radio station.
•
•
q
/
(Fast Backward/Fast Forward)
Fast backwards or fast forwards. Press
repeatedly to change the search speed.
r
(Back)
Returns to a previous menu screen.
3
Connect your home
theater
This section helps you connect your home theater
to a TV and other devices. The basic connections of
the home theater with its accessories are provided
in the Quick Start. For a comprehensive interactive
guide, see www.connectivityguide.philips.com.
Note
• Refer to the type plate at the back or bottom
of the product for identification and supply
ratings.
• Before you make or change any connections,
ensure that all devices are disconnected from
the power outlet.
Connectors
Connect other devices to your home theater.
Side connectors
a MP3 LINK
Audio input from an MP3 player.
b
(USB)
Audio, video or picture input from a USB
storage device.
EN
7
Eng l i s h
p
Back connectors
Connect to the TV
Connect your home theater directly to a TV
through one of the following connectors
(from highest to basic quality video):
a HDMI
b Component video
c Composite video
a LAN
Connects to the LAN input on a broadband
modem or router.
b AC MAINS~
Connects to the power supply.
c HDMI OUT (ARC)
Connects to the HDMI input on the TV.
d VIDEO OUT
Connects to the composite video input on
the TV.
e COMPONENT VIDEO OUT
Connects to the component video input on
the TV.
Option 1: Connect to the TV through
HDMI
Note
• The HDMI connector on the TV might be
labeled HDMI IN or HDMI ARC .
• If the TV supports HDMI Audio Return
Channel (ARC), you can use it to output digital
audio to the home theater.
• If the HDTV has a DVI connector, connect
using an HDMI/DVI adapter.
• If the TV supports EasyLink HDMI CEC,
control the home theater and TV with one
remote control (see ‘Use Philips EasyLink’ on
page 17 ).
f SUBWOOFER
Connects to the supplied subwoofer.
g AUDIO IN - AUX
Connects to the analog audio output on the
TV or an analog device.
TV
h DOCK for iPod
Connects to a Philips Dock for iPod/iPhone.
(Model: Philips DCK3060, sold separately)
i DIGITAL IN - OPTICAL
Connects to the optical audio output on
the TV or a digital device.
j ANTENNA FM (75 )
Signal input from an antenna, cable or
satellite.
k DIGITAL IN-COAXIAL
Connects to the coaxial audio output on
the TV or a digital device.
8
EN
Option 2: Connect to the TV through
YPbPr (component video)
Note
• The component video cable or connector
might be labeled Y Cb Cr or YUV.
(Cable not supplied)
Component Video Out
Eng l i s h
Option 1: Connect audio through analog
audio cables
(Cable not supplied)
TV
Component Video In
TV
Option 3: Connect to the TV through
composite video (CVBS)
Note
• The composite video cable or connector might
be labeled AV IN , VIDEO IN , COMPOSITE or
BASEBAND.
(Cable not supplied)
TV
Option 2: Connect audio through
coaxial cable
Note
• The digital coaxial cable or connector might
be labeled COAXIAL/DIGITAL OUT or
SPDIF OUT.
Connect audio from TV or
other devices
Use your home theater to play audio from the
TV or other devices such as a cable box.
(Cable not supplied)
TV
Tip
• Press SOURCE / AUDIO SOURCE
repeatedly to select the audio output of your
connection.
EN
9
Option 3: Connect audio through a digital
optical cable
(Cable not supplied)
LAN
Note
• The digital optical cable or connector might be
labeled as SPDIF OUT or OPTICAL OUT.
(Cable not supplied)
TV
www
Connect to the Internet
Connect the home theater to the internet and
enjoy:
• BD-Live: You can access BD-Live
features (see ‘Access BD-Live on Bluray’ on page 13).
• Net TV : browse Net TV services (see
‘Browse Net TV’ on page 15).
• Software update: You can update the
software of the home theater through
the network (see ‘Update software
from the network’ on page 21).
What you need:
• A network router (with DHCP
enabled).
• A network cable (RJ45 straight cable).
• For Net TV and software update,
make sure that the network router
has access to the Internet and is not
restricted by firewalls or other security
systems.
Note
• Net TV feature only available in Latin America.
10
EN
Set up network
1
2
3
4
5
6
7
8
9
Connect the home theater to a broadband
modem or router (see ‘Connect to the
Internet’ on page 10).
Turn on your TV and switch to the correct
source for the home theater.
Press (Home).
Select [Setup], then press OK .
Select [Network] > [Network Installation],
then press OK .
Select [Wired (Ethernet)], then press OK .
Select [Auto (recommended)] or [Manual
(advanced)], then press OK .
Follow the instructions on the TV to
complete the setup.
» The home theater connects to the
internet. If connection fails, select [Retry],
then press OK.
Select [Finish], then press OK to exit.
Use your home
theater
This section helps you use the home theater to
play media from a wide range of sources.
Before you start
Check that you:
• Make the necessary connections
described in the Quick Start and User
Manual.
• Complete the first time setup. First
time setup appears when you turn on
the home theater for the first time. If
you do not complete the setup, you
are prompted to complete it each time
you turn on the home theater.
• Switch the TV to the correct source
for the home theater.
Access the home menu
The home menu gives you easy access to
connected devices, audio and video settings, and
other features.
Press (Home).
» The home menu appears.
1
2
Press the Navigation buttons and OK to
select the following:
• [play Disc] : Starts disc play.
• [browse USB] : Accesses the content
browser of the connected USB storage
device.
• [browse iPod] : Accesses the content
browser of the connected iPod or
iPhone.
• [browse Net TV] : Accesses Net TV.
• [Setup] : Accesses menus to change
picture, sound and other settings.
• [User Manual] : Launches the
electronic user manual.
Note
• Net TV feature only available in Latin America.
Choose your sound
This section helps you choose the ideal sound for
your video or music.
Press SOUND SETTINGS /
(Sound OPTIONS).
Press the Navigation buttons (left/right) to
access the sound OPTIONS.
1
2
Sound experience Description
AUTO VOLUME Sets a constant output signal
at the speaker output. This
option is best for TV audio
input where the commercial
signal level is usually higher
than the content.
SOUND
Selects a sound mode.
SURROUND
Selects a surround sound or
stereo sound.
TREBLE
Adjusts the high frequency
output.
MID
Adjusts the middle
frequency output.
BASS
Adjusts the low frequency
output.
AUDIO SYNC
Delays the audio to match
the video.
3
4
Select an option, then press OK .
Press
BACK to exit.
If you do not press a button within five
seconds, it automatically exits the menu.
Change auto volume
Select the level of volume which output from
your TV or other devices to the home theater.
Press SOUND SETTINGS /
(Sound OPTIONS).
Select AUTO VOLUME , then press OK .
Press the Navigation buttons (up/down) to
select ON or OFF.
Press OK to confirm your choice.
1
2
3
4
EN
11
Eng l i s h
4
Change sound mode
Change treble, mid and bass
Select predefined sound modes to suit your
video or music.
Press SOUND SETTINGS /
(Sound OPTIONS).
Select SOUND, then press OK .
Press the Navigation buttons (up/down) to
select the following settings:
• ACTION/ROCK : Enhanced low and
high-range. Ideal for action movies and
rock or pop music.
• PURE/PURE : Clear mid and highrange for sound purity.
• GAMING/PARTY : Moderate lowrange and strong mid-range. Ideal for
video games and party.
• CONCERT/CLASSIC : Neutral sound.
Ideal for live concerts and classical
music.
• SPORTS : Moderate mid-range and
surround effects for clear vocals and
the atmosphere of a live sport venue.
• NEWS : Enhanced mid-range for clear
vocals and speech.
Change the high frequency (treble), mid
frequency (mid) and low frequency (bass)
settings of the home theater to suit your video
or music.
Press SOUND SETTINGS /
(Sound OPTIONS).
Select TREBLE , MID or BASS , then press
OK .
Press the Navigation buttons (up/down) to
adjust the frequency level.
Press OK to confirm.
1
2
3
4
Press OK to confirm your choice.
Change surround sound mode
Experience an immersive audio experience with
surround sound modes.
Press SOUND SETTINGS /
(Sound
OPTIONS).
Select SURROUND, then press OK .
Press the Navigation buttons (up/down) to
select the following settings:
• AUTO : Surround sound output based
on the audio stream.
• STEREO : Two-channel stereo sound.
Ideal for listening to music.
• AMBISOUND : Stereo sound output
or multi-channel surround output.
1
2
3
4
1
2
3
4
Synchronize audio with video
If the audio and video are not synchronized, you
can delay the audio to match the video.
Press SOUND SETTINGS /
(Sound OPTIONS).
Select AUDIO SYNC , then press OK .
Press the Navigation buttons (up/down) to
sync the audio with the video.
Press OK to confirm.
1
2
3
4
Play a disc
The home theater can play a wide variety of
discs, including video, audio and mixed media
(for example, a CD-R that contains JPEG pictures
and MP3 music).
Insert a disc into the home theater.
Press DISC .
» The disc plays or the disc main menu appears.
1
2
3
Press the following buttons to control play:
Button
Action
Navigation buttons
OK
Navigate menus.
Confirms an entry or
selection.
Starts or resumes play.
Pauses play.
Stops play.
Skips to the previous
or next track, chapter
or file.
(Play)
Press OK to confirm your choice.
/
12
EN
/
Navigation buttons
(up/down)
SUBTITLE
POP-UP MENU/
DISC MENU /
(Disc menu)
OPTIONS /
(OPTIONS)
Action
Fast backwards or
fast forwards. Press
repeatedly to change the
search speed.
Rotates the picture
counter-clockwise or
clockwise.
Selects subtitle language
for video.
Accesses or exits the
disc menu.
Accesses more play
OPTIONS during
playback.
For video formats such as, DivX and WMV:
• To stop play, press .
• To resume the video from where you
stopped, press (Play).
• To play the video from the start, press
OK .
Note
4
5
Select [2nd Audio Language] or [2nd
Subtitle Language], then press OK .
Select the language to play, then press OK .
Note
• To turn off the Bonus View (Picture-inPicture), press
OPTIONS / (OPTIONS),
select [PIP Selection] > [Off], then press OK .
Access BD-Live on Blu-ray
BD-Live enabled Blu-ray discs include exclusive
services such as movies and other online bonuses.
Prepare the internet connection and set up
the network (see ‘Connect to the Internet’
on page 10).
Connect the USB storage device to the
home theater.
Select the BD-Live icon in the disc menu,
then pressOK .
» BD-Live starts to load. The loading time
depends on the disc and your internet
connection.
1
2
3
• To play DivX DRM - protected files from a disc
4
or a USB storage device, connect your home
theater to a TV through an HDMI cable.
5
Press the Navigation buttons to navigate
BD-Live.
Press OK to select an item.
Note
Use Bonus View on Blu-ray
Blu-ray discs that support the Bonus View
feature (also known as Picture-In-Picture) allow
you to view special content such as a director’s
commentary while watching the main feature.
If necessary, enable BonusView (or PictureIn-Picture) in the Blu-ray disc menu.
During playback of the main feature,
OPTIONS / (OPTIONS).
press
» The OPTIONS menu is displayed.
1
2
3
• The range of BD-Live services depends on
the disc.
• When you use BD-Live, data on the disc and
home theater are accessed by the content
provider.
• Use a USB storage device with at least 1 GB of
free space to store the downloaded files.
• If there is insufficient memory to download
BD-Live content, clear memory space (see
‘Change advanced settings’ on page 20).
Select [PIP Selection] > [PIP], then
press OK .
» PIP OPTIONS [1]/[2] depend on the
video contents.
» The picture-in-picture video appears in a
small window.
EN
13
Eng l i s h
Button
Play 3D video
Your home theater can play 3D videos on 3D TVs.
Before you start, make sure that:
• your TV is a 3D TV, and is connected
to your home theater through HDMI,
• your disc is a Blu-ray 3D disc, and
• you have 3D glasses that are
compatible with your 3D TV.
1
Insert a Blu-ray 3D disc into your home
theater.
» Your TV switches to the correct HDMI
source, and the disc plays automatically.
2
If the disc does not play automatically, press
DISC or select [play Disc] in the home
menu, and then press OK .
Press the play buttons to control play.
When you search forward or backward,
and in some other play modes, the video
displays in 2D. It returns to 3D when you
play normally again.
Put on the 3D glasses to enjoy the 3D
effects.
3
4
5
Note
• If the USB storage device does not fi t into the
connector, use a USB extension cable.
• The home theater does not support digital
cameras that need a computer program to
display photos.
• The USB storage device must be NTFS, FAT
or DOS-formatted, and Mass Storage Class
compliant.
More play features for disc
or USB
Several advanced features are available for video
or picture playback from a disc or USB storage
device.
Use video OPTIONS
Access several useful features while viewing video.
Play 3D discs in 2D
1
2
3
4
Press (Home).
Select [Setup] > [Video] >
[Blu-ray 3D video] > [Off].
Press OK .
Play your Blu-ray 3D disc.
» The 3D video is displayed in 2D.
Play from a USB storage device
The home theater is fitted with a USB connector
that allows you to view pictures, listen to music or
watch movies stored on a USB storage device.
Connect the USB storage device to the
home theater.
Press (Home).
» The home menu appears.
1
2
3
Select [browse USB], then press OK .
» A content browser appears.
4
Select a file, then press OK .
14
EN
Press the playback buttons to control play
(see ‘Play a disc’ on page 12).
Note
• Available video OPTIONS depend on the
video source.
1
Press
OPTIONS / (OPTIONS).
» The video OPTIONS menu appears.
2
Press the Navigation buttons and OK to
select and adjust:
• [Audio Language] : Selects audio
language for video.
• [Subtitle Language] : Selects subtitle
language for video.
• [Subtitle Shift] : Adjusts the subtitle
position on the screen.
• [Info] : Displays information about
what is playing.
• [Character Set] : Selects a character
set that supports the DivX subtitle.
• [Time Search] : Skips to a specific part
of the video by entering the time of
the scene.
• [2nd Audio Language] : Selects the
second audio language to play.
•
•
•
•
•
•
•
•
•
[2nd Subtitle Language] : Selects the
second subtitle language to play.
[Titles] : Selects a specific title.
[Chapters] : Selects a specific chapter.
[Angle List] : Selects a different camera
angle.
[Menus] : Displays the disc menu.
[PIP Selection] : Displays Picture-inPicture window.
[Zoom] : Zooms into a video scene or
picture. Press the Navigation buttons
(left/right) to select a zoom factor.
[Repeat] : Repeats a chapter or title.
[Repeat A-B] : Marks two points
within a chapter or track for repeat
play, or turns off repeat mode.
[Picture Settings] : Selects a
predefined color setting.
Use picture OPTIONS
Access several useful features while viewing
pictures.
Press
OPTIONS / (OPTIONS).
» The pictures OPTIONS menu appears.
1
2
Press the Navigation buttons and OK to
select and adjust:
• [Rotate +90] : Rotates the picture
90 degree clockwise.
• [Rotate -90] : Rotates the picture
90 degree counter-clockwise.
• [Zoom] : Zooms into a video scene or
picture. Press the Navigation buttons
(left/right) to select a zoom factor.
• [Info] : Displays picture information.
• [Duration per slide] : Sets the display
speed for each picture in a slide show.
• [Slide Animation] : Selects animation
for the slide show.
• [Picture Settings] : Selects a
predefined color setting.
• [Repeat] : Repeats a selected folder.
Use audio OPTIONS
Access several useful features while audio is
played.
Press
OPTIONS / (OPTIONS)
repeatedly to cycle through the following
functions:
• REPEAT TRACK : Repeats the current
track.
• REPEAT DISC : Repeats all the tracks
on the disc or folder.
• REPEAT RANDOM : Plays audio
tracks in random order.
• REPEAT OFF : Turns off repeat mode.
1
Play a musical slideshow
Play music and pictures simultaneously to create
a musical slideshow.
Select a music track, then press OK .
Press
BACK and go to the picture
folder.
Select a picture, then press OK to start
slideshow.
Press
to stop slideshow.
Press
again to stop music.
1
2
3
4
5
Browse Net TV
With the home theater connected to the Internet,
you can use Net TV to access videos, pictures,
music, information, games and other online
services.
Note
• Koninklijke Philips Electronics N.V. bears no
responsibility for content provided by Net TV
service providers.
Note
• Net TV feature only available in Latin America.
EN
15
Eng l i s h
•
Access Net TV
Button
Action
1
/
Navigation
buttons
(left/right)
Navigation
buttons
(up/down)
Selects a preset radio station.
Searches for a radio station.
2
Prepare the internet connection and set up
the network (see ‘Connect to the Internet’
on page 10).
Press (Home).
» The home menu appears.
3
Select [browse Net TV], then press OK .
» The Net TV home page appears.
4
Press the Navigation buttons to navigate
Net TV web pages or services.
Press OK to view or select an item.
Press
BACK to return to the previous
page, or press (Home) to exit.
5
6
Clear browsing history
Clear browsing history to remove passwords,
cookies and browsing data from your home
theater.
Press (Home).
Select [Setup], then press OK .
Select [Network] > [Clear Net TV
Memory], then press OK .
1
2
3
Fine tunes a radio frequency.
Press and hold to erase the
preset radio station.
Press to stop the installation
of radio stations.
OPTIONS / Manual: Press once to access
(OPTIONS) program mode, and press
again to store the radio station.
Automatic: Press and hold for
five seconds to reinstall radio
stations.
RADIO
Toggles between stereo and
mono sound.
Note
• AM and digital radio are not supported.
• If no stereo signal is detected, you are
prompted to install the radio stations again.
• For the best reception, place the antenna away
from the TV or other sources of radiation.
Play from radio
The home theater can store up to 40 radio
stations.
Check that the FM antenna is connected.
Press RADIO.
» “AUTO INSTALL...PRESS PLAY’ appears
on the display panel if you have not
installed any radio stations. Press (Play).
1
2
3
Press the following buttons to control play:
16
EN
Change tuning grid
In some countries, you can switch the FM tuning
grid between 50 kHz and 100 kHz. Changing the
tuning grid erases all preset radio stations.
Press RADIO.
Press
(Stop).
Press and hold (Play) to toggle between
100 kHz and 50 kHz frequency.
1
2
3
Listen to music
Press SOURCE / AUDIO SOURCE repeatedly
to select the audio output of the connected
device .
2
1
3
Play from an MP3 player
Connect and play audio files from an MP3 player
or other external audio devices.
Connect the MP3 player to the home
theater as described in the Quick start
guide.
Press SOURCE / AUDIO SOURCE
repeatedly until ‘ MP3 LINK’ appears on the
display panel.
Press the buttons on the MP3 player to
select and play audio files.
3
Note
• On iPod, enable the TV ON setting.
• On iPhone, select the TV Out option.
1
2
Play from an iPod or iPhone
By connecting and installing a Philips Dock for
iPod/iPhone, you can use the home theater to
play music, movies and photos from your iPod or
iPhone.
Note
• Philips Dock for iPod/iPhone is sold separately.
• You can charge your iPod/iPhone on the dock
while the home theater is in iPod mode.
Dock your iPod or iPhone
1
2
3
Connect the dock to the home theater and
connect the yellow composite cable from
the dock to the TV. For more information,
see the Quick Start provided with the dock.
Switch on the iPod or iPhone and place it in
the dock.
On the home theater remote control, press
(Home), then select [browse iPod] and
press OK .
Press the Navigation buttons and OK to
select and play tracks.
Watch video or view slideshows
1
2
Dock your iPod or iPhone (see ‘Dock your
iPod or iPhone’ on page 17 ).
Press DOCK for iPod on the home theater
remote control.
» The playlists are displayed on the TV.
3
4
Dock your iPod or iPhone (see ‘Dock your
iPod or iPhone’ on page 17 ).
Switch the TV to the AV/VIDEO source
(corresponding to the yellow composite
cable).
» The TV screen goes blank.
Browse on the iPod or iPhone screen to
select videos or photos.
Press (Play) to play the video and photos.
» The picture is displayed on the TV.
Use Philips EasyLink
The home theater supports Philips EasyLink,
which uses the HDMI CEC (Consumer
Electronics Control) protocol. EasyLinkcompliant devices that are connected through
HDMI connectors can be controlled by a single
remote control.
Note
• Philips does not guarantee 100%
interoperability with all HDMI CEC devices.
1
2
3
Switch on the HDMI CEC operations on
the TV and other connected devices. See
the manual of the TV or other devices for
details.
Press (Home).
Select [Setup], then press OK .
EN
17
Eng l i s h
Play audio from TV or other
devices
4
5
6
Select [EasyLink] > [EasyLink], then press
OK .
Select [On], then press OK .
You can now enjoy the following Philips
EasyLink controls.
5
Change settings
This section helps you to change the settings of
your home theater.
Caution
One-touch play
When you play a disc, the TV automatically
switches to the correct channel.
One-touch standby
When you press and hold (Standby) on the
remote control, the home theater and all the
connected HDMI CEC devices (if they support
one-touch standby) switch to standby mode
simultaneously.
System Audio Control
When you play a device that has its audio
output routed to the home theater, the home
theater switches to the corresponding audio
source automatically.
To use one-touch audio, enable this feature and
follow the instructions on the TV to map the
connected devices correctly to the audio input
jacks of the home theater.
Audio Input Mapping
Updates audio input mapping if there are new
devices connected.
• Most of the settings are already configured
with the best value for the home theater.
Unless you have a specific reason to change a
setting, it is best to leave it at the default value.
Access the setup menu
1
2
Press (Home).
Select [Setup], then press OK .
» The setup menu appears.
3
Select a setup menu, then press OK .
See the following sections for information
about how to change the settings of your
home theater.
Press
BACK to return to the previous
menu, or press to exit.
4
Note
• You cannot change a setting that is grayed out.
Change video settings
1
2
3
4
18
EN
Press (Home).
Select [Setup], then press OK .
Select [Video], then press OK .
Select and adjust the following settings:
• [TV Display]: Selects a picture display
format to fi t the TV screen.
• [HDMI Video]: Selects the HDMI
video resolution.
• [HDMI Deep Color]: Displays colors
with more shades and hues when the
video content is recorded in Deep
Color and the TV supports this feature.
• [Component Video]: Selects the
component video resolution. Copyprotected DVDs can display only
480p/576p or 480i/576i.
•
5
[Blu-ray 3D video]: Selects the
3-dimensional video output when you
play a 3D video on your home theater.
The home theater must be connected
to a 3D TV through HDMI.
[Picture Settings]: Selects a predefined
color setting.
Set up network
1
2
3
4
Press (Home).
Select [Setup], then press OK .
Select [Network], then press OK .
Select and adjust the following settings:
• [Network Installation] : Starts
wired (Ethernet) setup. Follow the
instructions to set up the network
connection.
• [View Network Settings] : Displays
the current network settings.
• [Net TV User Location] : Selects the
location for accessing Net TV content
and services.
• [Clear Net TV Memory] : Clears Net
TV memory, delete the temporary
downloaded files (e.g., cookies) of the
Net TV browser.
5
Press OK to confirm your choice.
Press OK to confirm your choice.
Note
• The best setting is automatically selected for
the TV. If you change the setting, ensure that
the TV supports the new setting.
• For settings related to HDMI, the TV must be
connected through HDMI.
• For settings related to progressive or
component video, the TV must be connected
through Component Video.
Change audio settings
1
2
3
4
5
Press (Home).
Select [Setup], then press OK .
Select [Audio] , then press OK .
Select and adjust the following settings:
• [Night Mode] : Selects quiet or full
dynamic sound. Night mode decreases
the volume of loud sounds and
increases the volume of soft sounds
such as speech.
• [HDMI Audio] : Selects HDMI audio
format or disables HDMI audio output
for the TV.
• [Ambisound Setup] : Sets up
Ambisound to give the best surround
sound effect. Follow the instructions
on the TV to complete the setup.
Press OK to confirm your choice.
Note
• For settings related to HDMI, the TV must be
connected through HDMI.
• Night mode is available for Dolby encoded
DVD and Blu-ray discs (for models support
Blu-ray playback).
Note
• Net TV feature only available in Latin America.
Set up EasyLink
1
2
3
4
Press (Home).
Select [Setup], then press OK .
Select [EasyLink], then press OK .
Select and adjust the following settings:
• [EasyLink] : Enables or disables
EasyLink.
• [One Touch Play] : Enables or disables
One Touch Play.
If enabled, you can use the remote
control to start disc play in the
home theater and the TV switches
automatically to the correct channel.
• [One Touch Standby] : Enables or
disables One Touch Standby.
If enabled, the home theater can
be switched off to standby by a
remote control from the TV or other
connected HDMI CEC devices.
EN
19
Eng l i s h
•
•
•
5
•
[System Audio Control] : Enables or
disables System audio control.
If enabled, follow the instructions on
the TV to map the connected devices
correctly to the audio connectors of
the home theater. The home theater
switches automatically to the audio
source of the connected device.
[Audio Input Mapping] : Updates audio
input mapping if there are new devices
connected.
•
•
Press OK to confirm your choice.
•
Note
•
• The connected devices must be connected
through HDMI and switched on.
5
Change preference settings
1
2
3
4
20
Press (Home).
Select [Setup], then press OK .
Select [Preference], then press OK .
Select and adjust the following settings:
• [Menu language] : Selects the
on-screen display menu language.
• [Audio] : Selects audio language for
video.
• [Subtitle] : Selects subtitle language for
video.
• [Disc Menu] : Selects menu language
for video disc.
• [Parental Control] : Restricts access
to discs that are recorded with ratings.
To play all discs irrespective of the
rating, select level ‘8’.
• [Screen Saver] : Enables or disables
screen saver mode. If enabled,
the screen enters idle mode after
10 minutes of inactivity (for example,
in pause or stop mode).
• [Auto Subtitle Shift] : Enables or
disables shift subtitle. If enabled,
it adjusts the subtitle position
automatically to fi t the TV screen.
EN
[Change Password] : Sets or changes
a PIN code to play a restricted disc.
Enter ‘ 0000’ if you do not have a PIN
or if you have forgotten your PIN.
[Display Panel] : Changes the
brightness of the display panel.
[Auto Standby] : Enables or disables
auto standby. If enabled, the home
theater switches to standby after 30
minutes of inactivity (for example, in
pause or stop mode).
[VCD PBC] : Displays or skips the
content menu for VCD and SVCD
discs.
[Sleep Timer] : Sets a sleep timer to
switch the home theater to standby
after a specific time.
Press OK to confirm your choice.
Note
• If your preferred disc language is not available,
you can select [Other] from the list and enter
the 4-digit language code which can be found
at the back of this manual.
• If you select a language that is not available
on a disc, the home theater uses the default
language of the disc.
Change advanced settings
1
2
3
4
Press (Home).
Select [Setup], then press OK .
Select [Advanced], then press OK .
Select and adjust the following settings:
• [BD-Live Security] : Restricts or allows
access to BD-Live.
• [Software Update] : Selects to update
software from the network or from
USB storage device.
• [Clear memory] : Clears local memory,
delete the BD-Live files that you
previously downloaded. If using an USB
storage device, the local storage folder
is ‘BUDA’.
•
•
5
[DivX® VOD Code] : Displays the
DivX VOD registration code for the
home theater.
[Version Info.] : Displays the software
version for the home theater.
[Restore default settings] : Resets the
home theater to the default settings
programmed at the factory.
Press OK to confirm your choice.
Note
• You cannot restrict internet access on
commercial Blu-ray discs.
6
To check for new updates, compare the current
software version of your home theater with the
latest software version (if available) on the Philips
web site.
Check software version
1
2
3
• Before you purchase DivX videos and play
them on the home theater, register the home
theater on www.divx.com using the DivX
VOD code.
• You cannot reset parental control setting to its
default value.
Update software
Press (Home).
Select [Setup], then press OK .
Select [Advanced] > [Version Info.], then
press OK .
» The software version is displayed.
Update software from the
network
1
2
3
4
Prepare the internet connection (see
‘Connect to the Internet’ on page 10).
Press (Home) and select [Setup].
Select [Advanced] > [Software Update] >
[Network].
» If an upgrade media is detected, you are
prompted to start or cancel the update.
Follow the instruction on the TV to confirm
the update.
» When complete, the home theater
automatically switches off and restarts.
• If not, disconnect the power cord for a
few seconds and then reconnect it.
Note
• If the home theater is unable to connect to the
Philips server, press (Home), select [Setup] >
[Network] > [Network Installation] to set up
the network.
EN
21
Eng l i s h
•
Update software from a USB
1
Check for the latest software version on
www.philips.com/support.
• Search for your model and click on
‘software and drivers’.
2
Create a folder named ‘UPG’ in the root
directory of your USB storage device.
Download the software into the ‘\UPG’
folder of the USB storage device.
Unzip the software in the ‘\UPG’ folder.
Connect the USB storage device to the
home theater.
Press (Home) and select [Setup].
Select [Advanced] > [Software Update] >
[USB].
Follow the instructions on the TV to
confirm the update.
» When complete, the home theater
automatically switches off and restarts.
• If not, disconnect the power cord for a
few seconds and then reconnect it.
3
4
5
6
7
8
Caution
• Do not turn off the power or remove the USB
storage device when the software update is in
progress because you might damage the home
theater.
Update electronic user manual
1
2
3
4
5
22
Check the current version of the electronic
user manual installed in your home theater
(see ‘Check software version’ on page 21).
Insert a USB storage device into your PC.
In your web browser, navigate to www.
philips.com/support, and find your product.
Click on ‘Software and drivers’ in the left
panel, and then locate the ‘Electronic
Manual’. The electronic user manual is
compressed into a *.zip archive.
If the *.zip file at the Philips Support website
is a later version than the file in your home
theater, download the file in the root
directory of your USB storage device.
EN
6
Unzip the downloaded file in the root
directory of the USB storage device.
» A file named ‘HTSxxxxeDFU.zip’ is
extracted in the ‘\UPG’ folder of your
USB storage device, ‘xxxx’ being the
model number of your home theater.
7
Disconnect the USB storage device from
the PC, and connect it to the home theater.
Press (Home).
• Ensure that there is no disc inside
the disc compartment of your home
theater and it is closed.
8
9
Press [3], [3], [8] on the remote control.
» Software update starts. When complete,
the home theater automatically switches
off and restarts.
10 When complete, disconnect the USB
storage device from the home theater.
Caution
• Do not turn off the power or remove the USB
storage device during the update.
• If power failure occurs during the update,
do not remove the USB flash drive from the
home theater. The home theater continues the
update as soon as the power is restored.
• If an error occurs during the update, retry
the procedure. If the error reoccurs, contact
Philips Consumer Care.
•
Product
specifications
Note
• Specification and design are subject to change
without notice.
Region code
The type plate on the back or bottom of the
home theater shows which regions it supports
Country
Europe,
United Kingdom
DVD
BD
Asia Pacific, Taiwan,
Korea
A
Latin America
A
Australia,
New Zealand
Russia, India
C
China
C
Playback media
•
AVCHD, BD-RE, BD-Video,
DVD-Video, DVD+R/+RW,
DVD-R/-RW, DVD+R/-R DL,
CD-R/CD-RW, Audio CD,
Video CD/SVCD, Picture CD,
MP3-CD, WMA-CD, DivX (Ultra)-CD,
USB storage device
File Format
•
Audio: .mp3, .wma, .mka
•
Video: .avi, .asf, .divx, .mkv, .mpg, .mpeg,
.wmv
•
Picture: .jpg, .gif, .png
•
Amplier
•
Total output power: 500W RMS, 10% THD
•
Frequency response: 40 Hz-20 kHz / ±3dB
Signal-to-noise ratio:
> 65 dB (CCIR) / (A-weighted)
•
Input sensitivity:
• AUX: 1500 mV
• MP3 LINK: 750 mV
Video
•
Signal system: PAL / NTSC
•
Component video output: 480i/576i,
480p/576p, 720p, 1080i
•
HDMI output: 480i/576i, 480p/576p, 720p,
1080i, 1080p, 1080p24
Audio
•
S/PDIF Digital audio input:
• Coaxial: IEC 60958-3
• Optical: TOSLINK
•
Sampling frequency:
• MP3: 32 kHz, 44.1 kHz, 48 kHz
• WMA: 44.1 kHz, 48 kHz
•
Constant bit rate:
• MP3: 112 kbps - 320 kbps
• WMA: 48 kbps - 192 kbps
Radio
• Tuning range:
• Europe/China:
FM 87.5-108 MHz (50 kHz)
• Asia Pacific/Russia/Latin America/India:
FM 87.5-108 MHz (50/100kHz)
• Signal-to-noise ratio: FM 55 dB
• Frequency response:
FM 60 Hz-12.5 kHz / ±3dB
USB
•
Compatibility: Hi-Speed USB (2.0)
•
Class support:
UMS (USB Mass Storage Class)
•
File system: NTFS, FAT16, FAT32
•
Maximum memory support: < 160GB
Main Unit
•
Power supply:
• Europe/Russia/China/India:
220-240V, ~50Hz
• Asia Pacific/Latin America:
110-127V/220-240V;
~50-60Hz switchable
•
Power consumption: 115 W
•
Standby power consumption: < 0.22 W
EN
23
Eng l i s h
7
•
Center speaker:
• Speaker impedance: 4 ohm
• Speaker driver:
2 x 64 mm (2.5”) full range
• Frequency response: 150 Hz-20 kHz
•
Front/Rear speakers:
• Speaker impedence: 6 ohm
• Speaker drivers:
4 x 64 mm (2.5”) full range
• Frequency response: 150 Hz-20 kHz
•
Dimensions (WxHxD): 955 x 155 x 96 mm
•
Weight: 6.4 kg
Subwoofer
•
Impedance: 4 ohm
•
Speaker driver: 165 mm (6.5”) woofer
•
Frequency response: 20 Hz-150 Hz
•
Dimensions (WxHxD):
196 x 397 x 342 (mm)
•
Weight: 6.03 kg
Wall Mount
•
Dimensions (WxHxD):
682 x 108 x 17 (mm)
•
Weight: 1.3 kg
Laser Specication
•
Laser Type : InGaN/AIGaN (BD),
InGaAIP (DVD), AIGaAs (CD)
•
Typical Wavelength: 405 nm (BD),
660 nm (DVD), 783 nm (CD)
•
Output power (Max. ratings):
20 mW (BD), 130 mW (DVD),
160 mW (CD)
8
Troubleshooting
Warning
• Risk of electric shock. Never remove the
casing of the product.
To keep the warranty valid, never try to repair the
product yourself.
If you have problems using this product, check the
following points before you request service. If you
still have a problem, register your product and get
support at www.philips.com/welcome.
If you contact Philips, you will be asked for the model
and serial number of your product.The model
number and serial number are on the back or
bottom of your product. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Main unit
The buttons on this home theater do not work.
•
Disconnect the home theater from the power
outlet for a few minutes, then reconnect.
Picture
No picture.
•
Ensure that the TV is switched to the
correct source for the home theater.
No picture on HDMI connection.
•
Change the HDMI video setting or wait for
15 seconds for auto recover.
•
Check if the HDMI cable is faulty. Replace
with a new HDMI cable.
No picture on the Component (Y Pb Pr) connection.
•
If the HDMI video connection is set to
[Auto] or [1080p/24Hz], there is no video
output through the component connection.
Change the HDMI video setting or remove
the HDMI connection.
No high-denition video signal on the TV.
•
Ensure that the disc contains high-definition video.
•
Ensure that the TV supports high-definition video.
Sound
No sound.
•
Ensure that the audio cables are connected
and select the correct input source (for
example, SOURCE / AUDIO SOURCE )
for the device you want to play.
24
EN
Play
Disc cannot be played.
•
Clean the disc.
•
Ensure that the home theater supports the
disc (see ‘Product specifications’ on page 23).
•
Ensure that the home theater supports the
region code of the disc.
•
For DVD±RW or DVD±R, ensure that the
disc is finalized.
DivX video les cannot be played.
•
Ensure that the DivX file is encoded
according to the ‘Home Theater Profile’
with the DivX encoder.
•
Ensure that the DivX video file is complete.
DivX subtitles do not display correctly.
•
Ensure that the subtitle file name is the
same as the movie file name.
•
Select the correct character set: 1) Press
OPTIONS / (OPTIONS). 2) Select
[Character Set]. 3) Select the supported
character set. 4) Press OK .
The contents of a USB storage device cannot be
read.
•
Ensure that the format of the USB storage
device is compatible with the home theater
(see ‘Product specifications’ on page 23).
•
Ensure that the USB storage device
is formatted with a file system that is
supported by the home theater.
‘No entry’ or ‘x’ sign appears on the TV.
•
The operation is not possible.
EasyLink feature does not work.
•
Ensure that the home theater is connected
to a Philips brand EasyLink TV and that
EasyLink is on.
I do not want my home theater to be switched
on when I switch on my TV.
•
This is the correct behavior for Philips EasyLink
(HDMI-CEC). To make the home theater work
independently, switch off EasyLink.
I cannot access BD-Live features.
•
Check the network connection (see
‘Connect to the Internet’ on page 10) or
ensure that the network has been set up
(see ‘Set up network’ on page 10).
•
Clear memory storage (see ‘Change
advanced settings’ on page 20).
•
Ensure that the Blu-ray disc supports
BD-Live feature.
The video (movies, photos, video clips, etc.)
contents of the iPod/iPhone do not display on TV.
•
Video and photo browsing is not supported,
you can only browse the video and photo
contents on the iPod/iPhone itself.
Cannot see pictures from my iPod/iPhone on the TV.
•
Connect a yellow composite cable from the
dock to the TV.
•
Switch the TV to the AV/VIDEO source
(corresponding to the yellow composite cable).
•
Press PLAY on the iPod or iPhone to start
the slideshow.
The audio is interrupted when I play music from
my iPod or iPhone in the docking station.
•
Ensure that you have installed the latest
firmware on your iPod or iPhone. For more
information, refer to the support website of
your iPod or iPhone.
My 3D video plays in 2D mode.
•
Ensure that your home theater is connected
to your 3D TV through HDMI.
•
Ensure that your disc is a Blu-ray 3D disc.
•
Ensure that the [Blu-ray 3D video] setting
is turned on (see ‘Change video settings’ on
page 18).
I see black video on my TV screen.
Ensure that your home theater is connected
•
to the TV through HDMI.
•
Switch to the correct HDMI source on your TV.
EN
25
Eng l i s h
No sound on HDMI connection.
•
You might not hear any sound if the
connected device is not HDCP (Highbandwidth Digital Content Protection)
compliant or only DVI compatible. Use an
analog or digital audio connection.
•
Ensure that the [HDMI Audio] is enabled.
No sound from TV program.
•
Connect an audio cable from the audio
input on the home theater to the audio
output on the TV, then press SOURCE /
AUDIO SOURCE repeatedly to select the
correct audio source.
Distorted sound or echo.
•
Ensure that the TV volume is muted or set
to minimum if you are playing audio through
the home theater.
Audio and video are not synchronized.
•
1) Press SOUND SETTINGS /
(Sound OPTIONS) . 2) Press the
Navigation buttons (left/right) repeatedly
until AUDIO SYNC is displayed, then
press OK . 3) Press the Navigation buttons
(up/down) to sync the audio with the video.
9
F
Index
le formats
3
3D video
14
H
HDMI CEC (see Easylink)
A
amplier
audio
connection
language
synchronize with video
audio input mapping
23
9
20
12
17, 19
B
BD-Live
access
set up
Bonus View
Browse
Net TV
13
10
13
15
C
care
change settings
chapter
connect
audio from TV
guide
other devices
TV
connectors
contact us
2
18
14
9, 17
7
9
8
7
24
23
17
I
Internet
BD-Live
connect
iPod
play
slideshow
13
10
17
17
L
language
audio
disc menu
on-screen display
subtitle
14, 20
20
20
14, 20
M
MP3
play
17
N
Net TV
network
set up
15
10
O
D
disc
play
supported discs
disposal of your product
DivX
character set
12
23
3
one-touch play
one-touch standby
overview
connectors
main unit
remote control
17, 19
17, 19
7
4
4
14
P
E
EasyLink
settings
26
EN
17, 19
password (PIN code)
picture
OPTIONS
rotate
slide show
troubleshooting
20
15
15
15, 15
24
13
13
13
14
14
12
17
12
16
25
14
2
23
T
time search video
title
troubleshooting
TV
audio from TV
connect
14
14
24
9, 17
8
U
USB
play
software update
14
22
V
R
radio
play
program
tune
recycle
region code
remote control
repeat
rotate pictures
16
16
16
3
23
4
14, 12
15
video
OPTIONS
synchronize with audio
14
12
S
safety
settings
EasyLink
parental control
preferences
slideshow
animation
duration
play from iPod/iPhone
play musical slideshow
software
update
version
sound
auto volume
mode
surround
treble and bass
troubleshooting
subtitle
language
subtitle shift
system audio control
2
19
20
20
15
15
17
15
21
21
11
12
12
12
24
14, 20
14, 20
17
EN
27
Eng l i s h
picture-in-picture
2nd audio language
2nd subtitle language
enable
play
2D video
3D video
disc
MP3 player
OPTIONS
radio
troubleshooting
USB storage device
product care
product specications
Language Code
Abkhazian
6566
Afar
6565
Afrikaans
6570
Amharic
6577
Arabic
6582
Armenian
7289
Assamese
6583
Avestan
6569
Aymara
6589
Azerhaijani
6590
Bahasa Melayu
7783
Bashkir
6665
Belarusian
6669
Bengali
6678
Bihari
6672
Bislama
6673
Bokmål, Norwegian
7866
Bosanski
6683
Brezhoneg
6682
Bulgarian
6671
Burmese
7789
Castellano, Español
6983
Catalán
6765
Chamorro
6772
Chechen
6769
Chewa; Chichewa; Nyanja 7889
9072
中文
Chuang; Zhuang
9065
Church Slavic; Slavonic 6785
Chuvash
6786
Corsican
6779
Česky
6783
Dansk
6865
Deutsch
6869
Dzongkha
6890
English
6978
Esperanto
6979
Estonian
6984
Euskara
6985
6976
Faroese
7079
Français
7082
Frysk
7089
Fijian
7074
Gaelic; Scottish Gaelic 7168
Gallegan
7176
Georgian
7565
Gikuyu; Kikuyu
7573
Guarani
7178
Gujarati
7185
Hausa
7265
Herero
7290
Hindi
7273
Hiri Motu
7279
Hrwatski
6779
Ido
7379
Interlingua (International)7365
Interlingue
7365
Inuktitut
7385
Inupiaq
Irish
Íslenska
Italiano
Ivrit
Japanese
Javanese
Kalaallisut
Kannada
Kashmiri
Kazakh
Kernewek
Khmer
Kinyarwanda
Kirghiz
Komi
Korean
Kuanyama; Kwanyama
Kurdish
Lao
Latina
Latvian
Letzeburgesch;
Limburgan; Limburger
Lingala
Lithuanian
Luxembourgish;
Macedonian
Malagasy
Magyar
Malayalam
Maltese
Manx
Maori
Marathi
Marshallese
Moldavian
Mongolian
Nauru
Navaho; Navajo
Ndebele, North
Ndebele, South
Ndonga
Nederlands
Nepali
Norsk
Northern Sami
North Ndebele
Norwegian Nynorsk;
Occitan; Provencal
Old Bulgarian; Old Slavonic
Oriya
Oromo
Ossetian; Ossetic
Pali
Panjabi
Persian
Polski
Português
7375
7165
7383
7384
7269
7465
7486
7576
7578
7583
7575
7587
7577
8287
7589
7586
7579
7574
7585
7679
7665
7686
7666
7673
7678
7684
7666
7775
7771
7285
7776
7784
7186
7773
7782
7772
7779
7778
7865
7886
7868
7882
7871
7876
7869
7879
8369
7868
7878
7967
6785
7982
7977
7983
8073
8065
7065
8076
8084
Pushto
Russian
Quechua
Raeto-Romance
Romanian
Rundi
Samoan
Sango
Sanskrit
Sardinian
Serbian
Shona
Shqip
Sindhi
Sinhalese
Slovensky
Slovenian
Somali
Sotho; Southern
South Ndebele
Sundanese
Suomi
Swahili
Swati
Svenska
Tagalog
Tahitian
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga (Tonga Islands)
Tsonga
Tswana
Türkçe
Turkmen
Twi
Uighur
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Walloon
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
8083
8285
8185
8277
8279
8278
8377
8371
8365
8367
8382
8378
8381
8368
8373
8373
8376
8379
8384
7882
8385
7073
8387
8383
8386
8476
8489
8471
8465
8484
8469
8472
6679
8473
8479
8483
8478
8482
8475
8487
8571
8575
8582
8590
8673
8679
8765
6789
8779
8872
8973
8979
9085