ENGLISH
CP-SW1000H
ENGLISH
Introduction
Thank you for purchasing this SHARP product. To obtain the best
performance from this product, please read this manual carefully. It
will guide you in operating your SHARP product.
General Information
Features
This subwoofer incorporates the Tymphany
Linear
Array
Transducer ( LAT ) technology developed by Tymphany Corporation.
This Technology uses a linear array of multiple smaller diaphragms
to generate sound as opposed to the single diaphragm used in the
conventional cone speakers. Such arrangement enables:
Powerful low bass without the need for large enclosures
compared to the conventional speakers, hence the sleek and
compact design of this subwoofer.
Minimization of structural vibrations which makes it possible to
place the subwoofer close to your audio system without affecting
the critical circuitry.
Cleaning cloth x 1
Subwoofer stand x 2
Spike x 4
Foot cushion x 4
Contents
General Information
Accessories
Page
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Please confirm that the following accessories are included.
Preparation for Use
Subwoofer preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Placing the subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Subwoofer connections to TVs . . . . . . . . . . . . . . . . . . . . . . . . . . 5
AC power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 7
Remote control x 1
AC power lead x 1
Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 8
Advanced Feature
Operating the TV with the remote control . . . . . . . . . . . . . . . . . 8
References
RCA cable (2 pins - 2 pins) x 1
E-1
RCA cable (1 pin - 2 pins) x 1
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Precautions
CP-SW1000H
Please ensure that the equipment is positioned in a well-ventilated
area and ensure that there is at least 10 cm (4") of free space
along the sides, top and back of the equipment.
10 cm (4")
10 cm (4")
10 cm (4")
10 cm (4")
Use the unit on a firm, level surface free from vibration.
Keep the unit away from direct sunlight, strong magnetic fields,
excessive dust, humidity and electronic/electrical equipment
(home computers, facsimiles, etc.) which generate electrical
noise.
Do not place anything on top of the unit.
Do not expose the unit to moisture, to temperatures higher than
60˚C (140˚F) or to extremely low temperatures.
If your system does not work properly, disconnect the AC power
lead from the wall socket. Plug the AC power lead back in, and
then turn on your system.
In case of an electrical storm, unplug the unit for safety.
Hold the AC power plug by the head when removing it from the
wall socket, as pulling the lead can damage internal wires.
The AC power plug is used as a disconnect device and shall
always remain readily operable.
Do not remove the outer cover, as this may result in electric
shock. Refer internal service to your local SHARP service
facility.
The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, tablecloths, curtains,
etc.
No naked flame sources, such as lighted candles, should be
placed on the apparatus.
Attention should be drawn to the environmental aspects of battery
disposal.
This unit should only be used within the range of 5˚C - 35˚C
(41˚F - 95˚F).
The apparatus is designed for use in moderate climates.
Warning:
The voltage used must be the same as that specified on this unit.
Using this product with a higher voltage other than that which is
specified is dangerous and may result in a fire or other type of
accident causing damage. SHARP will not be held responsible for
any damage resulting from use of this unit with a voltage other than
that which is specified.
Cooling fan
This unit is fitted with a cooling fan at the rear for improved cooling.
Do not cover the opening in this section with any obstacles.
Cooling fan
Caution:
The unit will get warm whilst being used. Do not touch the warm
areas of the unit for prolonged periods to avoid injury.
ENGLISH
General Information
General
Volume control
The sound level at a given volume setting depends on speaker
efficiency, location, and various other factors. It is advisable to avoid
exposure to high volume levels. Do not turn the volume on to full at
switch on. Listen to music at moderate levels.
9
E-2
CP-SW1000H
Controls and indicators
ENGLISH
Front panel
Reference page
1. Bass Reflex Duct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4. Crossover Frequency Control . . . . . . . . . . . . . . . . . . . . . . . . 8
5. ON/STAND-BY Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6. STAND-BY Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
General Information
1
2
3 4 5 6
Rear panel
Reference page
1. AC Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2. Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3. Audio Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Remote control
Reference page
1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2. On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. TV Operation Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4. Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . . 8
1 2 3
1
TV Operation Buttons (Only SHARP TV):
2
4
Remote
control
Plastic shield
3
On/Stand-by
Button
Sets the TV
Input Select
power to
Button (TV)
“ON” or
“STAND-BY”.
Press the
button to
switch the
input source.
Volume Up and
Down Buttons
Turn up/
down the TV
volume.
Switch up/
down the TV
channels.
Channel Up and
Down Buttons
Battery holder
E-3
Note:
Before using remote control, please remove plastic shield at battery
holder.
Note:
Some models of SHARP TV may not be operable.
Subwoofer preparation
Make sure to unplug the AC power lead before installing the main
unit or changing the position.
Placing the subwoofer
CP-SW1000H
ENGLISH
Installation image:
Select from three installation methods according to the preferred
position.
TV
Horizontal position
Using spikes
1 Tighten all spikes as shown
Notes:
When attaching the spikes, place the subwoofer on a cushion or
soft cloth to avoid damage.
The subwoofer can be leveled by adjusting the spikes.
Caution:
When using these spikes on glossy or slippery table such as on glass
top, this subwoofer may slip and fall off the table.
Using foot cushions
1 Attach the foot cushions as shown
Note:
When attaching the foot cushions, place the subwoofer on a cushion
or soft cloth to avoid damage.
Vertical position
1 Place subwoofer stand as shown
VCR
DVD player
DVD player
Place the subwoofer as shown.
Notes:
As the bass sound from the subwoofer is omni-directional, you
can place the subwoofer anywhere you like. However, it is
recommended to place it as close to the TV as possible.
The front panel of the subwoofer is not removable.
Caution:
Do not change the installation direction when the subwoofer is
turned on.
Do not allow any objects to fall into or to be placed in the bass
reflex ducts.
Do not stand or sit on the subwoofer as you may be injured.
Preparation for Use
VCR
Magnetically shielded speakers
The subwoofer can be placed near a TV set as the built-in speakers
are magnetically shielded. However, uneven colours may appear on
the screen depending on the type of TV.
If colour variation occurs.
Turn off the TV (from the power switch).
After 15 - 30 minutes, turn the TV on again.
Stand
If the colour variation is still present.
Move the subwoofer further away from the TV.
Do not place the unit near any kind of magnet or an electromagnet
as irregular colours may appear on the TV screen.
9
E-4
CP-SW1000H
ENGLISH
Subwoofer connections to TVs
Caution:
Turn off all other equipment before making any connections.
Notes:
Refer to the operation manual of the equipment to be connected.
Fully insert the plugs to avoid fuzzy pictures or noises.
Caution:
Tuner receiving for other audio system
Placing the aerial near the subwoofer unit AC power lead may
cause noise pick up. Place the aerial away from the subwoofer
unit for better reception.
Preparation for Use
Connecting to a TV
TV
Audio cable (supplied)
If the TV/monitor has an audio output, connect it to the AUDIO
INPUT sockets on the rear of the subwoofer.
Subwoofer
To audio output sockets
Audio cable (supplied)
To AUDIO
INPUT sockets
To SUBWOOFER PRE-OUT
socket
To AUDIO
INPUT sockets
TV
Subwoofer
E-5
Connecting to a TV (with subwoofer pre-out)
If the TV/monitor has subwoofer pre-out, connect it to the AUDIO
INPUT sockets on the rear of the subwoofer.
AC power connection
After checking all the connections have been made correctly,
connect the AC power lead to the AC power input socket, then to the
wall socket.
Remote control
CP-SW1000H
ENGLISH
Battery installation
1
Whilst pushing the locking tab towards the centre of the
remote control, slide out the battery holder.
Back of remote control
Wall socket
(AC 220 - 240 V ~ 50 Hz (Europe))
(AC 220 - 240 V ~ 50/60 Hz (others))
2
Remove the old battery from the battery holder, insert the
new battery and then slide the battery holder back into the
remote control.
Battery holder
Notes:
Never use a power lead other than the one supplied. Otherwise,
a malfunction or an accident may occur.
Unplug the AC power lead from the wall socket if the unit will not
be in use for a prolonged period of time.
Positive (+) side up
Polarity (+) symbol
Battery type
Locking tab
Precautions for battery use:
Remove the battery if the unit will not be used for long periods of
time. This will prevent potential damage due to battery leakage.
Preparation for Use
Locking tab
Caution:
Do not use rechargeable battery (nickel-cadmium battery, etc.).
Replace only with the same or equivalent type.
Installing the battery incorrectly may cause the unit to malfunction.
Danger of explosion if battery is incorrectly replaced.
Batteries (battery pack or batteries installed) shall not be exposed
to excessive heat such as sunshine, fire or the like.
9
E-6
CP-SW1000H
ENGLISH
General control
Remote control (continued)
Notes concerning use:
Replace the battery if the operating distance is reduced or if the
operation becomes erratic. Purchase “CR 2025”, coin lithium
battery.
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit if this
occurs.
Keep the remote control away from moisture, heat, shock, and
vibrations.
Preparation for Use
Test of the remote control
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy your system.
Position A
Remote sensor
Position B
Remote sensor
To set the unit to stand-by mode:
Press the ON/STAND-BY button
again.
The STAND-BY indicator lights up
red.
0.2 m - 6 m
(8” - 20’)
15˚ 15˚
0.2 m - 6 m
(8” - 20’)
15˚ 15˚
E-7
To turn the power on
Press the ON/STAND-BY button.
The volume indicator lights up
blue.
If the power does not turn on,
check whether the power lead is
plugged in properly.
(Lights
up blue)
(Turns red)
Volume control
Main unit operation:
Turn volume knob clockwise to increase the volume and anticlockwise to decrease the volume.
Remote control operation:
Press the VOL + button to increase the volume and the VOL – button
to decrease the volume.
Note:
Do not turn the volume knob manually in reverse direction when
operating it by remote control.
Operating the TV with the remote
control
CP-SW1000H
ENGLISH
You can operate SHARP TV with this system’s remote control.
TV operation buttons
Notes:
Observe the following to avoid malfunction and sound distortion.
Do not set the volume too high on the audio system. The
subwoofer may be damaged.
Before you switch on/off the subwoofer, minimise the volume on
the audio system.
Watching TV
Point the remote control at the TV.
1
2
Auto power off
If no signal is detected for 20 minutes during power on, the
subwoofer will automatically go to stand-by mode.
3
Press the TV POWER button to turn on the TV.
Press the CH UP
channel.
Pressing the CH UP
channel switching.
or CH DOWN
or CH DOWN
button to set the
button enables TV
Advanced Feature
Crossover frequency control
Adjust the high frequency cut-off point. Frequencies higher than the
set frequency are removed.
To emphasise the bass, turn this control towards 80 Hz and increase
the volume.
Press TV VOL + or – button to adjust the TV volume.
Other operable button
Press the Input Select button to switch the input source. (TV)
Note:
Some models of SHARP TV may not be operable. In this case, use
the remote control supplied with each product.
9
E-8
CP-SW1000H
ENGLISH
Troubleshooting chart
Many potential problems can be resolved by the owner without
calling a service technician.
If something is wrong with this product, check the following before
calling your authorised SHARP dealer or service centre.
General
Symptom
References
No sound is heard.
Noise is heard during
playback.
Move the subwoofer away from any
computers or mobile phones.
When a button is
pressed, the unit
does not respond.
Set this unit to the stand-by mode and
then turn it back on.
The power is not
turned on.
Is the unit unplugged? (Refer to page 6)
The protection circuit may be activated.
Unplug and plug in the power lead again
after 5 minutes or more.
Remote control
Symptom
The remote control
does not operate
properly.
The subwoofer cannot
be turned on with the
remote control.
TV cannot be
operated with the
remote control.
E-9
Possible cause
Is the input signal (selection) set
properly?
Is the volume level set to “0”?
Possible cause
Is the battery polarity correct?
Is the battery dead?
Is the distance or angle incorrect?
Are there any obstructions in front of the
subwoofer?
Is there a strong light shining on the
remote sensor?
Is the remote control for another
equipment used simultaneously?
Is the AC power lead of the subwoofer
plugged in?
Is the battery inserted?
Depending on the model, some or all
functions may not be operable using the
remote control of this unit. In this case,
use the remote control supplied with the
TV.
Condensation
Sudden temperature changes, storage or operation in an extremely
humid environment may cause condensation inside the cabinet.
Condensation can cause the unit to malfunction. If this happens,
leave the power on until normal playback is possible (about 1 hour).
Wipe off any condensation on the transmitter with a soft cloth before
operating the unit.
If problem occurs
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.
If such a problem occurs, do the following:
1. Set the unit to the stand-by mode and turn the power on again.
2. If the unit is not restored in the previous operation, unplug and
plug in the subwoofer, and then turn the power on.
Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth.
Caution:
Do not use chemicals for cleaning (petrol, paint thinner, etc.). It
may damage the cabinet finish.
Do not apply oil to the inside of each component. It may cause
malfunctions.
Specifications
As part of our policy of continuous improvement, SHARP reserves
the right to make design and specification changes for product
improvement without prior notice. The performance specification
figures indicated are nominal values of production units. There may
be some deviations from these values in individual units.
CP-SW1000H
ENGLISH
General
Power source
Power consumption
Amplification system
Output power
Audio input terminal
Type
Impedance
Dimensions
Weight
Crossover frequency
AC 220 - 240 V ~ 50 Hz (Europe)
AC 220 - 240 V ~ 50/60 Hz (others)
Power on: 18 W
Power stand-by: 0.6 W(*)
Subwoofer: Pulse width modulation
RMS: 100 W (50 W + 50 W) (DIN 45 324)
Analog input: RCA type x 1 pair (L/R)
Subwoofer system
4 ohms x 2
Width: 430 mm (16-15/16")
Height: 151 mm (5-15/16")
Depth: 323.5 mm (12-3/4")
6.4 kg (14.11 lbs.)
80 Hz - 220 Hz
( * ) This power consumption value is obtained when in the power
stand-by mode.
References
Maintenance
9
E-10