U
DESKTOP AUDIO SYSTEM
SYSTEME AUDIO DESKTOP
TSX-120
OWNER’S MANUAL
MODE D’EMPLOI
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK DO
NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
1
2
3
4
5
6
7
8
9
•
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
10
11
12
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
13
14
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused
for long periods of time.
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, Yamaha and the Electronic Industries Association’s Consumer Electronics Group
recommend you to avoid prolonged exposure from excessive volume levels.
i En
IMPORTANT SAFETY INSTRUCTIONS
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which can
be determined by turning the unit “OFF” and “ON”, please
try to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave., Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
● The name plate is located on the bottom of the unit.
AVERTISSEMENT
L’utilisation de commandes et l’emploi de réglages ou de
méthodes autres que ceux décrits ci-dessous, peuvent
entraîner une exposition à un rayonnement dangereux.
ii En
Caution: Read this before operating your unit.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this unit in a well ventilated, cool, dry, clean place
with at least 15 cm on the top, 10 cm on the left and right,
and 10 cm at the back of this unit — away from direct
sunlight, heat sources, vibration, dust, moisture, and/or
cold.
Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes
from cold to hot (or vice versa), and do not locate this
unit in an environment with high humidity (i.e., a room
with a humidifier) to prevent condensation inside this
unit, which may cause an electrical shock, fire, damage to
this unit, and/or personal injury.
Avoid installing this unit where foreign object may fall
onto this unit and/or this unit may be exposed to liquid
dripping or splashing. On the top of this unit, do not
place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e., candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may overheat,
possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this might
damage the finish.
Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. Yamaha will not be held responsible for any
damage resulting from use of this unit with a voltage
other than specified.
To prevent damage by lightning, keep the power cable
and outdoor antennas disconnected from a wall outlet or
this unit during a lightning storm.
Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any service is
needed. The cabinet should never be opened for any
reasons.
When not planning to use this unit for long periods of
time (i.e., vacation), disconnect the AC power plug from
the wall outlet.
Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit
is faulty.
Before moving this unit, press ON/OFF to set the system
to off, and disconnect the AC power plug from the wall
outlet.
iii En
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the system off, then leave this unit
alone for cooling.
20 Install this unit near the wall outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit itself
is turned off by ON/OFF. In this state, this unit is designed to
consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide
slot and fully insert.
This Class B digital apparatus complies with Canadian ICES003.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type.
Taking care of the unit
When you wipe this unit, use a clean dry cloth.
CONTENTS
ADDITIONAL INFORMATION
PREPARATIONS BEFORE USING THIS UNIT
.............................................................................. 2
Turning on/off the system.......................................... 4
Adjusting the clock .................................................... 4
TROUBLESHOOTING .......................................15
General..................................................................... 15
iPod™ ...................................................................... 15
Radio reception........................................................ 16
Remote control ........................................................ 16
PREPARATION
PREPARATION
SPECIFICATIONS...............................................17
OPERATION
OPERATION
USING USEFUL FUNCTIONS ............................ 5
Using the alarm functions.......................................... 5
Setting sleeping mode................................................ 8
Setting Dimmer mode................................................ 8
Switching DSP mode................................................. 8
BASIC OPERATION............................................. 9
LISTENING TO iPod™ AND EXTERNAL
SOURCES ......................................................... 10
ADDITIONAL
INFORMATION
Listening to your iPod™ ......................................... 10
Playing back external sources.................................. 12
LISTENING TO FM RADIO STATIONS ........ 13
Connecting antennas................................................ 13
Tuning radio stations ............................................... 13
Presetting radio stations........................................... 13
Selecting preset radio stations (Preset tuning)......... 14
■ About this manual
•
•
•
•
In this manual, operations that can be performed with either this unit or its remote control are explained using the unit.
The symbol “☞” with page number(s) indicates the corresponding reference page(s).
Notes contain important information about safety and operating instructions. y indicates a tip for your operation.
This manual is printed prior to production. Design and specifications are subject to change in part as a result of
improvements, etc. In case of differences between the manual and the product, the product has priority.
■ Supplied accessories
This product includes the following accessories. Make sure you have all of the following parts.
Remote control
Indoor FM antenna
(1.4 m (55-1/8”))
Owner’s manual
U
DESKTOP AUDIO SYSTEM
SYSTEME AUDIO DESKTOP
TSX-120
OWNER’S MANUAL
MODE D’EMPLOI
English
1 En
PREPARATION
PREPARATIONS BEFORE USING THIS UNIT
1 Source buttons: AUX, FM, iPod (☞ P. 9)
2 ON/OFF: System on/off (☞ P. 4)
3 VOLUME: Volume control buttons (☞ P. 9)
4 Audio control buttons (☞ P. 9)
5 iPod dock (☞ P. 10)
6 AUX in (☞ P. 12)
7 Alarm control buttons (☞ P. 5)
8 SNOOZE/SLEEP (☞ P. 7, 8)
9 Speakers
0 FM control buttons (☞ P. 13)
A Front panel display (☞ P. 4)
B To the wall outlet
C CLOCK SET (☞ P. 4)
D FUNCTION
E DISPLAY (☞ P. 11)
F DSP: DSP mode switching (☞ P. 8)
G Infrared signal transmitter (☞ P. 3)
H SLEEP: Sleep time setting (☞ P. 8)
I MENU S/T /Center buttons* (☞ P. 10)
J RANDOM/REPEAT: Changing the playback mode for
iPod (☞ P. 10)
* The round shaped button on the center is called Center in this
manual.
2 En
PREPARATIONS BEFORE USING THIS UNIT
■ Before using the remote control
1 Remove the battery insulation sheet before using the remote
control.
PREPARATION
2 Remove the transparent sheet before using the remote control.
■ Using the remote control
Use the remote control within 6 m (20’) of this unit and point it
toward the remote control sensor.
Notes
Within 6 m
(20’)
• Do not spill liquid on the remote control.
• Do not drop the remote control.
• Do not leave the remote control in the following places:
– hot or humid places such as a bathroom or near a heater
– extremely cold places
– dusty places
■ Replacing the battery in the remote control
Change the battery when the operation range of the remote control decreases.
Use a straight pin to remove
the cover.
Replace the battery with
a new CR2025 battery.
Close the cover.
Notes
•
•
•
•
•
Insert the battery according to the polarity markings (+ and –).
If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak.
If a battery starts leaking, dispose of it immediately. Be careful not to let the leaking battery acid touch your skin or clothing.
Before inserting new batteries, wipe the compartment clean.
Dispose of batteries according to your regional regulations.
English
3 En
PREPARATIONS BEFORE USING THIS UNIT
Turning on/off the system
Adjusting the clock
The clock is not set at the factory.
1
Connect the power cable to the wall
outlet.
2
Press ON/OFF to turn on the system.
When the system is on: “Hello” appears, then clock and
other information are displayed.
Example: iPod playback mode display
1
Press CLOCK SET.
2
Select each setting with MENU S/T
and confirm with Center.
When the system is off: “Good-bye” appears, then only
date and time are displayed.
y
• This unit has an auto off function, which will automatically
switch the system to off if the system is left turned on for 1 hour
without playback or any other operation being performed. This
function is only available when the source is set to iPod.
• Press and hold ON/OFF on the top of the unit for more than 3
seconds to set the system to standby mode. All the information
on the front panel display is not displayed in standby mode.
This can reduce the power consumption. To cancel standby
mode, press ON/OFF.
• Even in system off/standby mode, the alarm function is
available.
• The memory back-up circuit prevents stored data such as the
time setting from being lost even in system off/standby mode.
4 En
You can set YEAR → MONTH → DAY → TIME.
Notes
• This operation can be performed only with the remote control.
• Time appears in 12-hour notation (AM/PM), depending on the
model. For example, “4:00PM”.
• You can switch 12-hour/24-hour notation by pressing
FUNCTION → MENU S/T → Center to select TIME
FORMAT, then pressing MENU S/T → Center to select
12H/24H.
• The time settings are lost after one week when the power cable
is disconnected from the wall outlet.
OPERATION
USING USEFUL FUNCTIONS
Using the alarm functions
2
Set the alarm time.
The unit has the dual alarm function. Each alarm time
always appears on the right/left sides of the clock on the
front panel display. When the alarm is set to on, the alarm
indicator and time light up.
You can set the different music to the alarm from what
you listen to during the setting.
1 While setting the alarm function, the alarm
indicator blinks.
2 The item you are setting also blinks.
3 The > mark on the right side means that you have
other menu items on the following screens. You
can go to the next menu item setting by pressing
ENTER.
3
OPERATION
Note
This operation can be performed only with the buttons on the top
of the unit.
Select and set TYPE → BEEP →
SOURCE → VOLUME.
■ Setting the alarm time and sound
Note
To cancel the alarm function setting during the operations, press
SETUP1/SETUP2. The alarm is not set.
1
Start setting ALARM1/ALARM2.
When you want to set the alarm to ALARM1, set on
SETUP1, and SETUP2 is for ALARM2.
1 After setting the alarm time, select the alarm type
from BEEP/BEEP+MUSIC/MUSIC.
– BEEP: beep sound only
– BEEP+MUSIC: beep sound and music selected
in an input source, iPod/FM
– MUSIC: music only
If you set TYPE to BEEP+MUSIC, you can play
back the desired music in an input source, iPod/
FM and beep sound together at the time you set.
The music volume gradually increases to wake
you up comfortably, and then the beep sound
plays back at the time you set.
English
5 En
USING USEFUL FUNCTIONS
2 Select the beep sound.
5 kinds of beep sounds are stored on the unit.
The BEEP screen is skipped automatically if you
select MUSIC/BEEP+MUSIC in step 1.
y
You can preview the currently displayed beep sound by
pressing SNOOZE/SLEEP when you select the beep
sound. To stop the beep sound, press SNOOZE/SLEEP
again.
Note
If the SOURCE is not set completely or the music device is
not set, the unit plays back the beep sound instead. For
example, if the unit cannot read your iPod, the beep sound
plays back.
4 Set the alarm volume.
The volume is set with ENTER in step 4, then the
alarm setting is complete. The alarm is set to on
automatically.
3 Select the music source from iPod/FM or LAST
SET.
■ Switching on/off the alarm
You can switch on/off the alarm with ALARM1/
ALARM2, but the alarm settings are not deleted with this
operation.
The SOURCE screen is skipped automatically if
you select BEEP in step 1.
Switch on/off the alarm function.
iPod
You can select PLAYLIST or RESUME PLAY.
The music starts from the beginning of the
playlist. Before this operation, make a playlist on
your iPod (☞ P. 7).
Select and set PLAYLIST.
Select and set the desired playlist.
Select and set RESUME PLAY when you want to
resume the music, which you listen to last time, as
the alarm sound.
FM
Set preset number/frequency.
LAST SET
Keep the setting you set last time.
6 En
When the alarm is on, the alarm indicator and time light
up.
USING USEFUL FUNCTIONS
■ Using the snooze function
■ Stopping the alarm sound
When the beep sound, music, or both are played back, you
can set the snooze function.
You can stop the alarm sound in the 3 ways as follows.
When you stop alarm sound, the system is set to off.
Set the snooze function.
Press ALARM1/ALARM2.
Press ON/OFF.
BEEP: The beep sound stops by pressing SNOOZE/
SLEEP, and resumes after 5 minutes.
MUSIC: The music stops by pressing SNOOZE/SLEEP,
and resumes after 5 minutes.
Press and hold SNOOZE/SLEEP for 2
seconds.
OPERATION
The function differs depending on the alarm type you set
in TYPE (☞ P. 5).
BEEP+MUSIC: With one click of SNOOZE/SLEEP,
you can stop the beep sound and keep playing back the
music. The beep sound resumes after 5 minutes.
y
You can also set the snooze function by pressing SLEEP on the
remote control instead of SNOOZE/SLEEP on the unit.
y
• If you do not stop the alarm, the alarm stops after 60 minutes
automatically.
• When you stop the alarm, the alarm indicator disappears. To
activate the alarm function again, press ALARM1/ALARM2 to
set the alarm to on.
• When you stop the alarm, the time setting, etc., is saved for
convenient use next time.
Note
Any operations other than setting the snooze function, stopping
the alarm sound, or adjusting the volume control are not available
while playing back the alarm sound.
■ About Playlist
You can collect your favorite songs in the library on your
iPod and make a list. This is a playlist. If you select a
playlist for playback, the songs in the playlist will be
played back. Even if you delete a song in a playlist, it is
not deleted from the library.
y
For more details on playlists, refer to the instruction manual of
your iPod.
English
7 En
USING USEFUL FUNCTIONS
Setting sleeping mode
2
Select the desired dimmer level.
You can set the time to turn off the system automatically.
Select the sleep time.
Press repeatedly.
Switching DSP mode
When the sleep function is on, the SLEEP indicator lights
up.
You can switch the sound mode according to the
environment or your preference.
y
You can also operate this function with SLEEP on the remote
control.
Setting Dimmer mode
You can change the brightness of the front panel.
If you set DIMMER to AUTO, the dimmer level is
adjusted automatically, depending on the brightness of the
room. If your room is dark, the front panel becomes
darker.
Switch DSP mode.
Press repeatedly.
Each time you press DSP the setting switches as follows:
NORMAL: For normal sound
↓
MILD: For natural and mild sound
↓
y
The default setting is AUTO.
1
Select DIMMER from the FUNCTION
menu.
y
After you select DIMMER with Center, < appears on the
left side of the front panel display. You can go back to the
FUNCTION menu by pressing MENU on the remote
control.
8 En
HEAVY: For more powerful sound
(default setting)
↓
LIVE: For wide realistic sound
↓
Back to NORMAL
BASIC OPERATION
:Press one of the Source buttons to select the desired source.*
OPERATION
:Press to control the volume.
:Press to play/pause.
: Press to skip backward/forward.
:Press to turn off the
sound. Press again to
resume the volume.
* Even when the system is off, you can start playback of the desired source by pressing one of the Source buttons, without pressing
ON/OFF.
English
9 En
LISTENING TO iPod™ AND EXTERNAL SOURCES
Listening to your iPod™
■ Selecting music on iPod with the remote
control
You can also operate with your iPod only when LIST
DISP is set to iPod (☞ P. 11).
Notes
• The unit is compatible with iPod touch, iPod (Click Wheel
including iPod classic), iPod nano and iPod mini.
• You can remove your iPod whenever you want.
• Some features may not be available depending on the model or
the software version of your iPod.
■ Playing back normally
1
Set your iPod into the iPod dock.
iPod
Dock Adapter
MENU: Go back to the previous menu.
Center: Confirm.
S/T: Select menu or items.
■ Using shuffle/repeat mode
After the above steps 1 and 2, you can enjoy shuffle and
repeat mode.
Notes
• A compatible Dock Adapter (not supplied) is required to
attach to the unit.
• The iPod may not be set in the iPod dock securely if it is in
its protective case.
2
Press RANDOM to switch shuffle mode
for iPod.
Press repeatedly.
Select iPod.
Playback starts.
y
For operations of your iPod, refer to the instruction manual of
your iPod.
Note
You cannot set ALBUM when you use an iPod touch.
Switch repeat mode.
Press repeatedly.
10 En
LISTENING TO iPod™ AND EXTERNAL SOURCES
■ Switching the playback information
display
■ Switching the playback list display
LIST DISP allows you to select iPod or the front panel
display of the unit to display the list.
Example: When LIST DISP is set to F.PANEL
If you set LIST DISP to iPod, you can also control
playback operations and display the menu list on the iPod.
OPERATION
Switch the display in iPod playback
mode.
Press repeatedly.
You can change the information display as follows.
Song number and elapsed time (default setting)
↓
Song number and remaining time
↓
Song name
↓
Artist name
↓
Album name
↓
y
The default setting is iPod.
Note
When LIST DISP is set to F.PANEL, the menu list appears only
on the front panel display of the unit, and all playback operations
except stop are available only on the unit. These operations are
not available with your iPod.
1
Select LIST DISP from the
FUNCTION menu.
2
Select iPod/F.PANEL.
Back to the default setting
Notes
• This function is available for iPod touch, iPod classic, iPod 5th
generation or later, and iPod nano. However, even with these
models, this function may not be available depending on the
software version of your iPod.
• If you intend to disconnect the power cable of the unit for a long
time, remove the iPod from the unit.
English
11 En
LISTENING TO iPod™ AND EXTERNAL SOURCES
Playing back external sources
■ Playing back normally
1
Connect your portable audio device
to the AUX terminal using a
commercially available 3.5 mm mini
plug cable.
Note
Turn down the volume of this unit and your portable audio device
before connection.
2
Select AUX.
3
Start playback on the connected
portable audio device.
y
For operations of the portable audio device, refer to the
instruction manual of the device.
12 En
LISTENING TO FM RADIO STATIONS
Connecting antennas
Indoor FM antenna
(supplied)
Presetting radio stations
You can store your favorite FM stations with the preset
function.
OPERATION
■ Auto preset
1
Press and hold MEMORY for more
than 2 seconds in FM mode.
2
Start the auto preset.
Notes
• The antenna should be stretched out.
• If radio reception is poor, change the height, direction, or
placement of the antenna.
• If you use an outdoor antenna instead of the supplied FM
antenna, reception will be better.
Tuning radio stations
■ Manual preset
1
2
Turn on FM.
1
Tune into a favorite radio station.
2
Press MEMORY.
3
Select the preset number you want
to store to.
Start automatic tuning.
Press and hold.
y
Note
If you tune to a station manually, the sound is monaural.
English
• If the signal received from the station you want to select is
weak, you can also tune into radio stations manually by
pressing TUNING<</>> repeatedly.
• You can also use TUNING<</>> on the front of the unit.
Note
To cancel the manual preset, press MEMORY again.
13 En
LISTENING TO FM RADIO STATIONS
4
Complete the manual preset.
y
• You can preset up to 30 FM stations.
• You can delete a preset station by pressing FUNCTION →
MENU S/T → Center to select PRESET DELETE.
Note
When you perform the auto preset, all stored stations are cleared
and the new stations are stored.
Selecting preset radio stations
(Preset tuning)
Select the preset radio station in FM
mode.
y
You can also use PRESET</> on the front of the unit.
14 En
ADDITIONAL INFORMATION
TROUBLESHOOTING
In case of a problem with the unit, check the following list first. If you cannot solve your problem with the suggested
solutions or if your problem is not listed below, turn off and unplug the unit, and consult the nearest authorized Yamaha
dealer or service center.
General
Problem
The system turns on but
immediately shuts off.
Solution
Make sure the power cable is plugged
into the wall outlet firmly.
The unit may have received a strong
electrical shock such as lightning or
excessive static electricity.
Set the system to off, and disconnect
the power cable. Wait about 30
seconds, reconnect the power cable, and
turn on the system.
The volume may be set to the
minimum level.
Adjust the volume level (☞ P. 9).
The mute function may be on.
Cancel the mute function (☞ P. 9).
The source may be incorrect.
Select the correct source (☞ P. 9).
Sound suddenly turns off.
The sleep timer (☞ P. 8) may be set.
Turn on the system and play the source
again.
The unit does not operate
properly.
The unit may have received a strong
electrical shock such as lightning or
excessive static electricity, or power
supply may have dropped.
Set the system to off, and disconnect
the power cable. Wait about 30
seconds, reconnect the power cable, and
turn on the system.
A digital or high-frequency
equipment produces noises.
The unit may be placed too close to
the digital or high-frequency
equipment.
Place the unit farther away from the
equipment.
The clock setting has been
cleared.
The unit is left more than one week
after you disconnect the power cable
from the wall outlet.
Plug the power cable into the wall
outlet firmly, and set the clock again
(☞ P. 4).
ADDITIONAL
INFORMATION
The speakers make no
sound.
Cause
The power cable may be connected
improperly.
iPod™
Problem
Cause
Solution
“iPod Connect Error”
appears on the front panel
display.
There is a problem with
communication between the unit and
your iPod.
Turn off the system and reconnect your
iPod to the unit.
The iPod does not charge
up.
The iPod is set in the iPod dock
improperly.
Remove the iPod from the unit, then set
it in the iPod dock again.
“iPod Not Connected”
appears on the front panel
display after you set the
iPod.
English
The iPod makes no sound.
The iPod sounds, but you
cannot operate it with the
unit or the remote control.
15 En
TROUBLESHOOTING
You cannot operate from the
iPod.
LIST DISP is set to F.PANEL.
Set LIST DISP to iPod from the
FUNCTION menu (☞ P. 11).
The playback information is
not displayed on the front
panel display.
The iPod you set is not compatible
with the playback information
display.
Only iPod touch, iPod classic, iPod 5th
generation or later, and iPod nano are
compatible with the function.
“Unknown iPod” appears on
the front panel display after
you set the iPod.
The iPod being used is not supported
by the unit.
Only iPod touch, iPod (Click Wheel,
including iPod classic), iPod nano and
iPod mini are supported.
Radio reception
Problem
Cause
Solution
The preset selecting
function does not work.
The preset (memory) may have been
erased.
Preset radio stations again (☞ P. 13).
Too much noise during
stereo broadcast.
The FM antenna may be connected
improperly.
Make sure the FM antenna is connected
properly (☞ P. 13).
The radio station you selected may be
far from your area, or the radio wave
reception is weak in your area.
Try manual tuning to improve the
signal quality (☞ P. 13) or use a multichannel outdoor antenna.
Multipath reflection or other radio
interferences may have occurred.
Change the height, direction, or
placement of the antenna.
Even with an outdoor
antenna, radio wave
reception is weak. (Sound is
distorted.)
Remote control
Problem
Cause
The remote control does not
work properly.
The remote control may be operated
outside its operation range.
For information on the remote control
operation range, refer to “Using the
remote control” (☞ P. 3).
The remote control sensor on the unit
may be exposed to direct sunlight or
lighting (inverted fluorescent lamps).
Change the lighting or orientation of the
unit.
The battery may be worn out.
Replace the battery with a new one
(☞ P. 3).
There are obstacles between the
sensor of the unit and the remote
control.
Remove the obstacles.
16 En
Solution
SPECIFICATIONS
■ PLAYER SECTION
■ TUNER SECTION
iPod
• Tuning range
U.S.A. model................................................. 87.50 to 107.90 MHz
Other models ................................................. 87.50 to 108.00 MHz
• Supported iPod.......... iPod touch, iPod (Click Wheel including iPod
classic), iPod nano, iPod mini
AUX IN
• Input connector .................STEREO L/R: 3.5 Φ STEREO mini Jack
■ AMPLIFIER SECTION
• Minimum RMS output power per channel ...................15 W + 15 W
(6 Ω 1 kHz, 10% THD)
• Driver unit..........................................8 cm (3”) full-range driver × 2
■ GENERAL
• Power Supply
U.S.A. model....................................................... AC 120 V, 60 Hz
Other models ............................................ AC 220 to 240 V, 50 Hz
• Power consumption................................................................... 20 W
• Standby Power consumption......................................... 1.0 W or less
• Dimensions (W × H × D) ................................. 350 × 120 × 240 mm
(13-3/4 × 4-3/4 × 9-7/16 in)
• Weight .................................................................. 3.7 kg (8 lbs. 3 oz)
Specifications are subject to change without notice.
ADDITIONAL
INFORMATION
iPod™
“iPod” is a trademark of Apple, Inc., registered in the U.S. and
other countries.
“Made for iPod” means that an electronic accessory has
been designed to connect specifically to iPod and has been
certified by the developer to meet Apple performance
standards.
Apple is not responsible for the operation of this device or
its compliance with safety and regulatory standards.
English
17 En
Printed in Malaysia
WQ45760-1