AB
DESKTOP AUDIO SYSTEM
TSX-80
OWNER’S MANUAL
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
Install this unit in a well ventilated, cool, dry, clean
place - away from direct sunlight, heat sources,
vibration, dust, moisture and cold. For proper
ventilation, allow the following minimum clearances.
Top: 15 cm (6 in)
Rear: 10 cm (4 in)
Sides: 10 cm (4 in)
Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this unit
in an environment with high humidity (i.e. a room
with a humidifier) to prevent condensation inside this
unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
Avoid installing this unit where foreign object may
fall onto this unit and/or this unit may be exposed to
liquid dripping or splashing. On the top of this unit,
do not place:
– Other components, as they may cause damage
and/or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall
and liquid may cause electrical shock to the user
and/or damage to this unit.
Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause
fire, damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may
overheat, possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall
outlet, grasp the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified is
dangerous and may cause fire, damage to this unit,
and/or personal injury. Yamaha will not be held
responsible for any damage resulting from use of this
unit with a voltage other than specified.
To prevent damage by lightning, keep the power
cable disconnected from a wall outlet or this unit
during a lightning storm.
Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
i En
15 When not planning to use this unit for long periods of
time (i.e. vacation), disconnect the AC power plug
from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press
to set the system to
off, and disconnect the AC power plug from the wall
outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the system off, then leave this
unit alone for cooling.
20 Install this unit near the wall outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat
such as sunshine, fire or the like. When you dispose
of batteries, follow your regional regulations.
22 Be sure to use the AC adaptor supplied with this unit.
Using an AC adaptor other than the one provided
may cause fire or damage to this unit.
This unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off by . In this state, this unit is
designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
There is a chance that placing this unit too close to a
CRT-based (Braun tube) TV set might impair picture
color. Should this happen, move this unit away from the
TV set.
PREPARATION
CONTENTS
NAMES OF PARTS AND THEIR FUNCTIONS
............................................................................... 2
BASIC FUNCTIONS........................................... 4
LISTENING TO iPod™ AND EXTERNAL
SOURCES............................................................. 6
LISTENING TO DAB STATIONS .................... 7
LISTENING TO FM STATIONS ...................... 9
TROUBLESHOOTING..................................... 10
SPECIFICATIONS............................................ 12
■ Features
– Hi-quality iPod/iPhone, radio (DAB/FM) and external device playability.
– Firm bass sound and spacious stereo sound from 2.1 ch speaker system (tweeter × 2, woofer × 1), SRBass™ (Yamaha Swing Radiator Bass technology) and DSP in a compact unit.
– Easy user-intuitive interface by buttons with Guide LED and knob dials.
■ About this manual
• This unit is iPod and also iPhone-compatible. “iPod” described in this manual may also refer to “iPhone”.
• This manual describes how to operate this unit using buttons on the unit. Some of these operations are also
available using the remote control.
■ Supplied accessories
Remote control
AC adaptor
Power cable
Dock cover
(DC 15 V, 2.66 A,
model number:
NU40-2150266-I3)
■ Using the remote control
■ Replacing the battery in the remote
control
CR2025
battery
Within 6 m
(20’)
1 En
NAMES OF PARTS AND THEIR FUNCTIONS
■ Front and top panel
Set your iPod in the iPod dock (see E below).
y
An iPod is charged when set in the iPod dock.
Dock Adaptor
Notes
• To secure the connection, attach a compatible Dock
Adaptor supplied with the iPod.
• The iPod may not be set in the iPod dock securely
if it is in its protective case.
1
: Press to turn the system on/off.
Time is displayed even when the system is off.
y
• Press and hold
on the top of the unit for more than 3
seconds to set the system to standby mode. All the
information on the front panel display is not displayed
in standby mode. This can reduce power consumption.
To cancel standby mode, press .
• Even in system off/standby mode, the alarm function is
available.
2 TIMER: Timer setting (☞ P. 5)
3 ALARM: Alarm on/off (☞ P. 4)
4 SET: Alarm setting (☞ P. 4)
5 Front panel display
6 SOURCE: iPod, AUX, RADIO
7 VOLUME: Volume control
8 PRESET: Storing your favorite 5 DAB and 5 FM
radio stations (☞ P. 8, P. 9)
9 SNOOZE/SLEEP (☞ P. 5)
2 En
0 DIMMER: Setting brightness of the front panel
A (auto) 3 (brightest) 2 1 (darkest) back to A
y
When A (auto) is set, the brightness of the front panel is
adjusted automatically depending on the brightness of the
room.
A MEMORY (☞ P. 7, P. 8, P. 9)
B TUNING (☞ P. 7, P. 9)
C DAB/FM: Switching DAB/FM (☞ P. 7, P. 9)
DISPLAY: Switching the DAB information display
(☞ P. 8)
D DAB information display: Displaying DAB
information
E iPod dock: Set an iPod.
y
Cover the iPod dock with the dock cover when not using.
F Illumination sensor: Measuring surrounding
illuminance. Do not cover this sensor.
NAMES OF PARTS AND THEIR FUNCTIONS
■ Rear panel
15V
: Connect supplied
AC adaptor and power cable.
AUX: Connect an
external device. (☞ P. 6)
ALARM TYPE switch (☞ P. 4)
DAB/FM rod antenna
(See below.)
TONE CONTROL: As you turn the
knob clockwise, Bass and Treble are
emphasized more.
CLOCK switch (☞ P. 4)
■ Extending rod antenna
DAB/FM rod antenna
Notes
• When you listen to DAB/FM, extend the
antenna.
• If DAB/FM reception is poor, change the
height or direction of the antenna, or relocate
the unit.
■ Remote control
Infrared signal transmitter
iPod control buttons
Source buttons: iPod, AUX,
RADIO. RADIO button switches
DAB/FM when SOURCE is set
to RADIO.
: System on/off
SLEEP: Sleep setting
(☞ P. 5)
ALARM: Alarm on/off
(☞ P. 4)
VOLUME: Volume control
TUNING: Tuning DAB/
FM (☞ P. 7, P. 9)
PRESET: Select the preset DAB/
FM station. (☞ P. 8, P. 9)
Battery insulation sheet:
Remove before using.
3 En
OPERATION
BASIC FUNCTIONS
Adjusting the clock
1 Set CLOCK to SET.
2 Set the time with TUNING.
3 Set CLOCK to LOCK.
Note
Rear panel
Front panel display
flashes.
The time settings are lost approximately one
week after unplugging the unit.
Alarm setting
This unit can play back iPod/radio (DAB/FM) and/or beep sound at the set time.
■ Setting the alarm time and sound
1 Press SET.
2 Set the alarm time with
TUNING.
3 Set ALARM TYPE.
Alarm indicator (
)
and front panel display
flashes.
Rear panel
(As required)
• SOURCE+BEEP: selected source
(played back from 3 minutes before
the alarm time) and beep sound
(played back at the alarm time)
• SOURCE: selected source
• BEEP: beep sound only
When you select SOURCE+BEEP or
SOURCE, select:
• iPod: this unit resumes the song you
listened to last time.
• RADIO: this unit plays back the
DAB/FM station you listened to last
time.
4 Set the alarm volume.
5 Press SET.
Alarm is set and the alarm indicator
(
) lights up.
Note
When iPod is selected as a source, set the iPod
in the iPod dock (☞ P. 2). If iPod is not set at
the alarm time, beep sound is played back.
■ Switching the alarm on/off
Switch on/off the alarm function.
When the alarm is on, the alarm
indicator (
) lights up and alarm
time is displayed for a while.
4 En
BASIC FUNCTIONS
Operations during playing back alarm sound
At the set time, alarm sound plays back. During playback, operations below are available.
■ Using the snooze function
Press SNOOZE/SLEEP.
The alarm sound stops and resumes
after 5 minutes.
■ Stopping the alarm
Press ALARM or
.
y
• Unless you stop the alarm, the alarm stops
after 60 minutes automatically.
• When you stop the alarm, the alarm time
setting, etc., is saved for convenient use next
time.
Sleep setting
You can set the time to turn off the system automatically when sleep is set to on.
Select the sleep time.
You can set 30, 60, 90 or 120 minutes.
When the sleep function is on, the
sleep indicator (
) lights up.
Press repeatedly.
Sleep indicator (
) and front
panel display flash.
y
To cancel the sleep, press SNOOZE/SLEEP.
Timer setting
You can set the countdown timer.
1 Press TIMER.
2 Set the countdown time with
TUNING.
Front panel
display flashes.
Countdown
starts.
You can set the time,
• 1 to 15 minutes: minute steps.
• 20 to 120 minutes: 10-minute steps.
3 Press TIMER.
Countdown starts. When the timer
reaches 0, the timer sound plays back.
y
• To stop the timer sound, press TIMER.
• To cancel the timer, press TIMER during
countdown.
Note
Sleep and timer cannot be used together.
• Sleep cannot be set during countdown.
• Sleep is set to off when timer is set while
sleep is on.
5 En
LISTENING TO iPod™ AND EXTERNAL SOURCES
Listening to your iPod™
For details on compatible iPod models, refer to “SPECIFICATIONS” (☞ P. 12).
■ Playing back
1 Set your iPod in the iPod dock.
2 Set SOURCE to iPod.
3 Play the iPod.
Playback operations are available with
both the remote control and the iPod
set in the iPod dock.
y
• You can remove the iPod whenever you want.
• When music/video in the iPod is played back,
this unit turns the system on automatically
and plays back the iPod even if the unit is
system off.
• This unit turns the system off automatically
after a while if the iPod is turned off or
removed from the iPod dock when SOURCE
is set to iPod.
Playing back external sources
■ Playing back
Rear panel
1 Connect your portable audio
device to AUX using a
commercially available 3.5 mm
(1/8 in) mini plug cable.
Note
Turn down the volume of this unit and your
portable audio device before connection.
2 Set SOURCE to AUX.
3 Start playback on the
connected portable audio
device.
6 En
LISTENING TO DAB STATIONS
DAB (Digital Audio Broadcasting) uses digital signals for clearer sound and more stable reception compared to
analog signals.
DAB is broadcast in blocks of data called ‘ensembles’ containing up to several radio stations that are
simultaneously broadcast.
DAB can also include an extensive amount of text information enabling you to select a station by name.
Other information, such as the name of song and artist or several kinds of news can be displayed on the DAB
information display.
Preparing for DAB reception
Before tuning into DAB stations, an initial scan must be performed.
When you select the DAB for the first time, the initial scan is performed automatically.
1 Set SOURCE to RADIO.
2 Select DAB with DAB/FM.
3 The initial scan starts.
During the scan, degree of progress is
displayed on the DAB information
display.
4 Scan is completed.
“Completed” and the number of
receivable DAB stations appear on the
DAB information display.
Top panel
Notes
• To perform initial scan manually, press and
hold MEMORY for 3 seconds and then press
MEMORY when scan starting screen is
displayed.
• If the initial scan is performed, stored DAB
station information and preset DAB stations
are cleared.
Top panel
Tuning DAB stations
1 Set SOURCE to RADIO.
2 Select DAB with DAB/FM.
3 Select a DAB station with
TUNING.
7 En
LISTENING TO DAB STATIONS
DAB station information
■ Basic information
While receiving DAB, switch the DAB information display.
When the unit does not receive a DAB signal, “Off Air” is displayed instead of the DAB station name.
Select DAB information by
pressing DISPLAY repeatedly.
Information is displayed in order
shown below.
Press repeatedly.
Text information
Ensemble name ( is displayed before
the ensemble name.)
Status 1 (channel label and frequency)
Status 2 (audio format and signal quality)
Back to the top.
■ Indicators on the DAB information display
Secondary indicator:
Some stations have sub
(secondary) stations. During
listening a secondary station, the
secondary indicator is displayed.
Signal strength indicator:
shows current signal strength.
Presetting DAB stations
You can store your favorite 5 DAB stations with the preset function.
1 Tune into a favorite DAB
station.
2 Press MEMORY.
3 Select the PRESET number
you want to store to.
y
To cancel the preset, press TUNING again.
4 Press MEMORY to complete.
Selecting preset DAB stations
1 Set SOURCE to RADIO.
2 Select DAB with DAB/FM.
3 Select the preset DAB station
with PRESET.
8 En
LISTENING TO FM STATIONS
Tuning FM stations
1 Set SOURCE to RADIO.
2 Select FM with DAB/FM.
3 For automatic tuning, press
and hold TUNING.
For manual tuning, press
TUNING repeatedly.
Note
If you tune to a station manually, the sound
is monaural.
Presetting FM stations
You can store your favorite 5 FM stations with the preset function.
1 Tune into a favorite FM station.
2 Press MEMORY.
3 Select the PRESET number
you want to store to.
y
To cancel the preset, press TUNING again.
4 Press MEMORY to complete.
Selecting preset FM stations
1 Set SOURCE to RADIO.
2 Select FM with DAB/FM.
3 Select the preset FM station
with PRESET.
9 En
ADDITIONAL INFORMATION
TROUBLESHOOTING
In case of a problem with the unit, check the following list first. If you cannot solve your problem with the
suggested solutions or if your problem is not listed below, turn off and unplug the unit, and consult the nearest
authorized Yamaha dealer or service center.
General
Problem
The speakers make no
sound.
Cause
The volume may be set to the minimum
level.
Solution
Adjust the volume level.
The source may be incorrect.
Select the correct source.
Sound suddenly turns off.
The sleep (☞ P. 5) may be set.
Turn on the system and play the source
again.
Sound is cracked/distorted
or there is abnormal noise.
Input source volume is excessive, or
volume of this unit is excessive
(especially Bass).
Adjust volume with VOLUME, or adjust
Bass with TONE CONTROL.
The unit does not operate
properly.
The unit may have received a strong
electrical shock such as lightning or
excessive static electricity, or power
supply may have dropped.
Set the system to off, and disconnect the
power cable. Wait about 30 seconds,
reconnect the power cable, and turn on the
system.
The system turns on but
immediately shuts off.
The power cable may be connected
improperly.
Make sure the power cable is plugged into
the wall outlet firmly.
The unit may have received a strong
electrical shock such as lightning or
excessive static electricity.
Set the system to off, and disconnect the
power cable. Wait about 30 seconds,
reconnect the power cable, and turn on the
system.
The unit may be placed too close to the
A digital or high-frequency
equipment produces noises. digital or high-frequency equipment.
Place the unit farther away from the
equipment.
The clock setting has been
cleared.
The unit is left more than one week after Plug the power cable into the wall outlet
you disconnect the power cable from the firmly, and set the clock again (☞ P. 4).
wall outlet.
iPod does not play back at
the alarm time even if
SOURCE is set to iPod.
The iPod is not set in the iPod dock.
Set the iPod in the iPod dock (☞ P. 2).
ALARM TYPE is set to BEEP.
Set ALARM TYPE to SOURCE+BEEP or
SOURCE (☞ P. 4).
Clock flashes and the unit
cannot be operated.
CLOCK on the rear panel is set to SET,
and this unit is in clock setting mode.
Set CLOCK to LOCK.
iPod™
Problem
No sound
Cause
The iPod is not set in the iPod dock
firmly.
Earphones are connected.
Remove the earphones.
The iPod software version has not been
updated.
Download the latest iTunes software to
update the iPod software version to the
latest.
The iPod does not charge up. The iPod is set in the iPod dock
improperly.
10 En
Solution
Set the iPod firmly.
Remove the iPod from the unit, and then set
it in the iPod dock again (☞ P. 2).
TROUBLESHOOTING
DAB reception
Problem
Cannot tune into any DAB
stations.
The initial scan operations
are not successful and “Not
found” appears on the DAB
information display.
Cause
Solution
The initial scan operations were not
performed.
Perform the initial scan operations
(☞ P. 7).
There is no DAB coverage in your area.
Check with your dealer or WorldDMB
Online at “http://www.worlddab.org” for a
listing of the DAB coverage in your area.
The DAB signals are too weak.
Change the height or direction of the
antenna, or relocate the unit.
The DAB signals are too weak.
Change the height or direction of the
antenna, or relocate the unit.
There is no DAB coverage in your area.
Check with your dealer or WorldDMB
Online at “http://www.worlddab.org” for a
listing of the DAB coverage in your area.
The DAB station reception is The DAB signals are too weak.
weak.
Change the height or direction of the
antenna, or relocate the unit.
There is noise interference
(e.g. hiss, crackle or jitter).
The antenna needs to be repositioned.
Change the height or direction of the
antenna, or relocate the unit.
The DAB signals are too weak.
Change the height or direction of the
antenna, or relocate the unit.
The DAB station information The DAB station may be temporarily out Contact the DAB broadcaster.
of service, or the DAB station
does not appear or is
information is not provided by the DAB
inaccurate.
broadcaster.
FM reception
Problem
Too much noise during
stereo broadcast.
FM wave reception is weak.
(Sound is distorted.)
Cause
Solution
The antenna needs to be repositioned.
Change the height or direction of the
antenna, or relocate the unit.
The FM station you selected may be far
from your area, or the FM wave
reception is weak in your area.
Try manual tuning to improve the signal
quality (☞ P. 9).
Multipath reflection or other radio
interferences may have occurred.
Change the height or direction of the
antenna, or relocate the unit.
Remote control
Problem
Cause
The remote control does not The remote control may be operated
outside its operation range.
work properly.
Solution
For information on the remote control
operation range, refer to “Using the remote
control” (☞ P. 1).
The remote control sensor on the unit
may be exposed to direct sunlight or
lighting (inverted fluorescent lamps).
Change the lighting or orientation of the
unit.
The battery may be worn out.
Replace the battery with a new one
(☞ P. 1).
There are obstacles between the sensor of Remove the obstacles.
the unit and the remote control.
11 En
SPECIFICATIONS
■ PLAYER SECTION
iPod™, iPhone™
iPod
iPod is a trademark of Apple Inc., registered in the U.S. and
other countries.
iPhone is a trademark of Apple Inc.
• Supported iPod .............iPod (5th generation), iPod classic,
iPod nano, iPod touch
• Supported iPhone.............. iPhone, iPhone 3G, iPhone 3GS
AUX IN
• Input connector
............ STEREO L/R: 3.5 mm (1/8 in) STEREO mini jack
■ AMPLIFIER SECTION
• Maximum output power ..........................4 W + 4 W + 8 W
(6 Ω 1 kHz, 10% THD)
• Driver unit .................. 4 cm (1 5/8 in) full-range driver × 2
5.5 cm (2 1/8 in) woofer + SR-Bass × 1
“Made for iPod” means that an electronic accessory has been
designed to connect specifically to iPod and has been
certified by the developer to meet Apple performance
standards.
“Works with iPhone” means that an electronic accessory has
been designed to connect specifically to iPhone and has been
certified by the developer to meet Apple performance
standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
■ TUNER SECTION
• Tuning range
FM .................................................. 87.50 to 108.00 MHz
DAB ..................................... 174 to 240 MHz (Band III)
■ GENERAL
•
•
•
•
•
Power supply ........................... AC 100 to 240 V, 50/60 Hz
Power consumption ..................................................... 10 W
System off consumption ............................................. 1.2 W
Standby consumption ......................................1.0 W or less
Dimensions (W × H × D) ..................... 260 × 90 × 164 mm
(10 1/4 × 3 1/2 × 6 1/2 in)
(including DAB/FM rod antenna)
• Weight ........................................................ 1.2 kg (2.6 lbs.)
Specifications are subject to change without notice.
■ For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
This unit supports DAB tuning.
12 En
■ Special Instructions for U.K.
Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED
IN ACCORDANCE WITH THE FOLLOWING
CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured BLUE must be connected
to the terminal which is marked with the letter N or
coloured BLACK. The wire which is coloured
BROWN must be connected to the terminal which is
marked with the letter L or coloured RED.
Make sure that neither core is connected to the earth
terminal of the three pin plug.
Limited Guarantee for European Economic Area (EEA) and Switzerland
Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service,
please contact the dealer from whom it was purchased. If you experience any difficulty, please contact Yamaha representative
office in your country. You can find full details on our website (http://www.yamaha-hifi.com/ or http://www.yamahauk.com/ for U.K. resident).
The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the
original purchase. Yamaha undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired,
or replaced at Yamaha’s discretion, without any charge for parts or labour. Yamaha reserves the right to replace a product with
that of a similar kind and/or value and condition, where a model has been discontinued or is considered uneconomic to repair.
Conditions
1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the
2.
3.
4.
5.
6.
7.
8.
defective product, along with a statement detailing the fault. In the absence of this clear proof of purchase, Yamaha
reserves the right to refuse to provide free of charge service and the product may be returned at the customer’s expense.
The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area
(EEA) or Switzerland.
The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.
The following are excluded from this guarantee:
a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.
b. Damage resulting from:
(1) Repairs performed by the customer himself or by an unauthorised third party.
(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the
customer’s responsibility to ensure the product is adequately packaged when returning the product for repair.
(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with
Yamaha’s instructions on the proper use, maintenance and storage, and (b) installation or use of the product in a
manner inconsistent with the technical or safety standards in force in the country where it is used.
(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control.
(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.
(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to
the technical or safety standards of the country of use and/or to the standard specification of a product sold by
Yamaha in the EEA and/or Switzerland.
Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the
country of use shall apply.
Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the
repair or replacement of the product.
Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such
settings or data.
This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s
rights against the dealer arising from their sales/purchase contract.
Information for Users on Collection and Disposal of Old Equipment
and Used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and
electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to
applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC
and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and prevent
any potential negative effects on human health and the environment which could otherwise arise from
inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your local
municipality, your waste disposal service or the point of sale where you purchased the items.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please contact your
local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
13 En
Printed in China
WU20300