- Industrial & lab equipment
- Electrical equipment & supplies
- Power conditioning
- Uninterruptible power supplies (UPSs)
- Tecnoware
- FAVPRE3
- Specification
advertisement
IT IS ADVISED TO READ THIS MANUAL CAREFULLY AND TO KEEP IT !
Thank you for choosing Power Reg. This AVR (Automatic Voltage Regulator) provides a good protection to all feeding devices.
This manual is a guide which enables you to correctly install and use your AVR. This manual includes important SAFETY instructions for the operator, for the AVR correct installation, and gives useful advice on the product. For any type of problem, please refer to this manual before calling the customer service.
IMPORTANT SAFETY INSTRUCTIONS
●
●
●
●
●
●
●
●
Only properly trained personnel must use the AVR. To ensure correct and safety operations, it is necessary that operators and maintenance personnel observe the general Safety Standards as well as the specific instructions included in this manual.
Electric Shock risk: do not remove the cover. The AVR contains internal parts at high voltage which are potentially dangerous, capable of causing injury or death by electric shock.
In the AVR there are no parts which are subject to user’s maintenance. Any type of maintenance and repair must be carried out exclusively by a qualified technical personnel authorised by TECNOWARE. TECNOWARE declines any responsibility if this warning is disregarded.
It is compulsory to ground the AVR according to Safety Standards in force.
When the AVR is ON there are risks of electric shock at the output sockets.
There are risks of electric shock at the output sockets if the unit is connected to the AC utility line.
Do not obstruct ventilation slots or holes and do not lean any object on top of the AVR. Do not insert objects or pour liquids in the ventilation holes. Do not keep liquids, flammable gases or corrosive substances near the AVR.
Install the AVR indoors, in a protected, clean and moisture free environment.
INTRODUCTION
●
●
●
●
●
●
Power Reg is an AVR (Automatic Voltage Regulator) specifically designed to protect the connected devices from irregularities in the AC line such as under or overvoltages; Power Reg performs output voltage regulation and filters frequently occurring electrical disturbances (such as transients, spikes, interferences, etc.), thus protecting all devices connected to the outlets.
The AVR general characteristics are:
Low/High voltage automatic regulation
Suitable for home and office equipments
Lightning and surge protection
Overload and short-cirtuit protection
Plug RJ11/45 (tel, modem, ADSL) protection
Heavy duty reliable design
INSTALLATION
INSPECTION AND PLACEMENT CHOICE
Carefully remove the AVR from its packaging, and carry out a meticulous inspection. We recommend keeping the original packaging in case you need to send the AVR for maintenance purposes.
We recommend to pay attention to the below points in order to choose a correct placement for your AVR:
●
●
●
Place Power Reg as close as possible both to the input electrical line and to the equipment to be supplied.
Power Reg is designed to operate in protected environments (for example: offices). We therefore recommend to install it in a place with no humidity, dust, or smoke. However, for the environmental requirements please refer to the “Specifications” chapter, and check that the selected place meets with such specifications.
It is necessary to leave at least 20 cm of space all around Power Reg in order to permit reasonable ventilation.
INSTALLATION
For a correct installation please carry out the following points:
1. Connect the AVR to an AC line outlet. It is mandatory to ground the outlet according to the Safety Standards. Carefully check the grounding, make sure that the utility power is available, and that its range falls within the AVR specifications (refer to the
“Specifications” chapter).
2. Connect the devices to the AVR output sockets and turn all the switches ON.
3. Turn On the AVR; check that the power up performance takes place properly and that the AVR does not give any warning signals.
Make sure that all devices are turned ON accordingly.
FUNCTIONING
TURN ON AND FUNCTIONING
To turn your AVR on it is sufficient to plug it to the AC utility line outlet and press the ON/OFF button on the front panel. Both the two led
(“POWER” and “REGULATE”)turn on. The “POWER” led is green.
Power Reg modes of functioning are:
1. “SUPER BOOST” mode: when Power Reg regulate a very low input voltage. In this case the “REGULATE” led is red.
2. “BOOST” mode: when Power Reg regulate a low input voltage. In this case the “REGULATE” led is orange.
3. “NORMAL” mode: when Power Reg works with a normal input voltage. In this case the “REGULATE” led turns off.
4. “BUCK” mode: when Power Reg regulate a high input voltage. In this case the “REGULATE” led is green.
TURN OFF
To turn your Power Reg OFF, it is enough to press the ON/OFF button.
“OVERLOAD” CONDITIONS
Power Reg is in the “OVERLOAD” condition when the output power is higher than declared. In case of “OVERLOAD”, the AVR may automatically switch off, protecting itself from this anomalous situation. In such case, the user must reduce the output power within the specification range, by disconnecting the devices causing the overload. The Circuit Breaker (on the rear) goes off in “OVERLOAD” or
short-circuit condition; push the external button of the Circuit Breaker to reactivate it.
SPECIFICATIONS
MODEL POWER REG 1 POWER REG 3
SI CONSIGLIA DI LEGGERE ATTENTAMENTE QUESTO MANUALE E CONSERVARLO !
Grazie per aver scelto Power Reg. Questo AVR (Automatic Voltage Regulator) fornisce un’ottima protezione a tutti i dispositivi alimentati.
Questo manuale è una guida per installare e utilizzare correttamente l’AVR. Nel manuale sono incluse importanti istruzioni di SICUREZZA per l’operatore e per una corretta installazione dell’AVR e utili consigli per la manutenzione del prodotto. Per ogni problema fare prima riferimento al manuale e poi rivolgersi al servizio d’assistenza.
IMPORTANTI AVVISI DI SICUREZZA
●
●
●
●
●
●
●
●
L'AVR deve essere utilizzato solo da personale opportunamente istruito. Per l’uso corretto e in condizioni di sicurezza è necessario che gli operatori ed il personale di manutenzione si attengano alle norme generali di sicurezza, in aggiunta alle norme specifiche contenute in questo manuale.
Rischio di shock elettrico: non rimuovere il coperchio. L’AVR presenta parti interne sotto tensione che sono potenzialmente pericolose e possono provocare lesioni o morte per shock elettrico.
L’AVR non ha parti interne soggette a manutenzione da parte dell’utente. Interventi tecnici di qualsiasi tipo devono essere compiuti solo da personale tecnico specializzato ed autorizzato da TECNOWARE. In caso contrario TECNOWARE declina ogni sua responsabilità.
Il collegamento a terra dell’AVR secondo le norme vigenti è obbligatorio.
Rischio di shock elettrico in uscita se l’AVR è acceso.
Rischio di shock elettrico in uscita se è presente la tensione di rete elettrica in ingresso.
Non ostruire le fessure o i fori di ventilazione e non appoggiare alcun oggetto sopra l’AVR; non inserire oggetti o versare liquidi nei fori di ventilazione; non avvicinare liquidi, gas infiammabili o sostante corrosive.
Installare l’AVR in ambiente chiuso, pulito e privo di umidità.
INTRODUZIONE
●
●
●
●
●
●
Power Reg è un AVR (Automatic Voltage Regulator), cioè un regolatore di tensione, realizzato appositamente per proteggere i dispositivi collegati da avarie della rete elettrica come sottotensionie sovratensioni; oltre a svolgere le funzioni di stabilizzatore, Power Reg filtra i disturbi frequentemente presenti sulla linea elettrica (transienti, spike, interferenze, etc.), preservando in tal modo i dispositivi che alimenta..
Le principali caratteristiche dell’AVR sono:
Regolazione automatica di basse e alte tensioni
Ideale come protezione in casa e in ufficio
Protezione da fulmine e surge
Protezione da cortocircuito e da sovraccarico
Protezione plug RJ11/45 (telefono, modem, ADSL)
Design innovativo ed affidabile
INSTALLAZIONE
ISPEZIONE E SCELTA DELLA COLLOCAZIONE
Rimuovere l’AVR dall’imballo con cautela e ispezionarlo accuratamente. Si consiglia di conservare l’imballo nell’eventualità futura che l’AVR debba essere spedito per la manutenzione.
Si consiglia di prestare attenzione ai punti seguenti per la scelta di una corretta collocazione dell’AVR:
●
●
●
Collocare Power Reg il più vicino possibile sia alla linea elettrica d'ingresso che ai dispositivi a cui deve fornire potenza.
Power Reg è progettato per operare in ambienti chiusi (come ad esempio gli uffici). Si consiglia perciò d’installarlo in un luogo privo di umidità, polvere e fumo eccessivi. Consultare comunque il capitolo “Caratteristiche Tecniche” per i requisiti ambientali e controllare che il luogo scelto rientri in tali specifiche.
È necessario lasciare uno spazio di almeno 20 cm su tutti i lati di Power Reg per permetterne una sufficiente aerazione.
INSTALLAZIONE
Per una corretta installazione svolgere i seguenti punti:
1. Collegare l’AVR ad una presa di alimentazione elettrica, che deve avere obbligatoriamente una connessione a terra secondo le
norme vigenti. Verificare il collegamento a terra della presa e accertarsi della presenza della tensione di rete elettrica e che la sua ampiezza rientri nelle specifiche (vedi capitolo “Caratteristiche Tecniche”).
2. Collegare i vari dispositivi alle prese d'uscita dell’AVR; posizionare i relativi interruttori su ACCESO.
3. Accendere l’AVR; controllare lo svolgimento della fase di accensione e che l’AVR non segnali nessuna anomalia. Accertarsi che tutti i dispositivi si siano accesi regolarmente.
FUNZIONAMENTO
ACCENSIONE E FUNZIONAMENTO
Per accendere l’AVR è sufficiente collegarlo alla linea elettrica e premere il pulsante ON/OFF sul pannello frontale. L’AVR accende entrambi i led (“POWER” e “REGULATE”) sul frontale. Il led “POWER” rimane acceso di colore verde.
Le modalità di funzionamento di Power Reg sono:
1. “SUPER BOOST” mode: quando Power Reg stabilizza una tensione di ingresso molto bassa. In questa modalità il led
“REGULATE” è rosso.
2. “BOOST” mode: quando Power Reg stabilizza una tensione di ingresso bassa. In questa modalità il led “REGULATE” è arancione.
3. “NORMAL” mode: quando Power Reg lavora con una tensione di ingresso all’interno di valori accettabili. In questa modalità il led
“REGULATE” è spento.
4. “BUCK” mode: quando Power Reg stabilizza una tensione di ingresso alta. In questa modalità il led “REGULATE” è verde.
SPENGIMENTO
Per spengere Power Reg è sufficiente premere il pulsante ON/OFF.
Condizioni di “OVERLOAD”
Power Reg è nella condizione di “OVERLOAD” quando la potenza assorbita dai dispositivi connessi supera quella dichiarata. In caso di
“OVERLOAD” l’AVR può spegnersi automaticamente per proteggersi dalla situazione anomala. Prima di riaccendere Power Reg verificare che il carico non superi la potenza massima dichiarata. In caso di “OVERLOAD” o cortocircuito l’interruttore termico (Circuit Breaker) sul retro dell’ AVR scatta; per riarmare il Circuit Breaker, premere manualmente sulla parte fuoriuscita.
CARATTERISTICHE TECNICHE
MODELLO POWER REG 1 POWER REG 3
POWER
NOMINAL INPUT VOLTAGE
INPUT VOLTAGE RANGE
FREQUENCY RANGE
OUTPUT VOLTAGE REGULATION
CERTIFICATIONS
AUDIBLE NOISE (at 1 meter)
COOLING
WEIGHT
DIMENSION (W x H x D)
ENVIRONMENTAL SPECIFICATIONS
FILTERED PHONE PLUG
WARRANTY
VA
V
% dBA
Kg cm
220 / 230
145 ~275 V
47 ~ 63 Hz
± 10
CE
< 40
Natural
1.4 1.7 2.3
11 x 17.5 x 15.2
Temperature 0-40 °C
Humidity 0-95% without condensation
Maximum altitude 3000mt
RJ11/45 included
2 years
Technical data may change without prior notice
POTENZA
TENSIONE NOMINALE INGRESSO
RANGE TENSIONE INGRESSO
RANGE FREQUENZA
REGOLAZIONE TENSIONE USCITA
CERTIFICAZIONI
RUMOROSITÀ (ad 1 metro)
RAFFREDDAMENTO
PESO
DIMENSIONI (L x H x P)
CONDIZIONI AMBIENTALI
OPERATIVE
PLUG TELEFONICO FILTRATO
GARANZIA
VA
V
%
600VA (420W) 1000VA (700W)
220 / 230
145 ~275 V
47 ~ 63 Hz
± 10
CE
1500VA (1050W)
dBA
Kg cm
< 40
Naturale
1.4 1.7 2.3
11 x 17.5 x 15.2
Temperatura 0-40 °C
Umidità 0-95% senza condensazione
Altitudine massima 3000 metri
RJ11/45 di serie
2 anni
I dati tecnici sono soggetti a variazioni senza preavviso
TECNOWARE
®
Power Reg
Front panel - Pannello frontale
Power Reg
Rear - Retro button
Pulsante ON/OFF
2. “REGULATE” Led
Led “REGULATE”
4. AC power input cord
Cavo d’ingresso
Interruttore termico (Circuit Breaker)
3. “POWER” Led
Led “POWER” Presa uscita
7. Filtered phone plug
Plug telefonico filtrato
EUROPEAN DIRECTIVES CONFORMITY
CONFORMITÀ ALLE DIRETTIVE EUROPEE
Tecnoware confirms that Power Reg models comply with the requirements set out in: the Low Voltage Directive (Safety) 73/23/EEC and following amendments, the EMC (Electro-Magnetic Compatibility) Directive 89/336/EEC and following amendments.
The following standards were applied:
Low Voltage Directive (Safety): EN50091-1-1:1996
EMC Directive (Electro-Magnetic Compatibility): EN50091-2: 1995
Tecnoware dichiara che i prodotti Power Reg sono conformi ai requisiti stabiliti nella Direttiva Bassa Tensione (Sicurezza) CEE 73/23 e successive modifiche, e nella Direttiva EMC (Compatibilità Elettromagnetica) CEE 89/336 e successive modifiche.
Sono state applicate le seguenti normative:
Direttiva Bassa Tensione (Sicurezza): EN50091-1-1:1996
Direttiva EMC (Compatibilità Elettromagnetica): EN50091-2: 1995
© Copyright 2004 TECNOWARE s.r.l. All right reserved
All trademarks are property of their respective owners.
Edition: August 2004 Version: 1.0.1
POWER REG
Automatic Voltage Regulator
USER’S MANUAL
MANUALE D’USO
TECNOWARE
®
Tecnoware srl
Via Lisbona, 9 - 50065 Pontassieve (FI) Italy
Tel. +39 055 8367554 - Fax +39 055 8367457 www.service.tecnoware.com [email protected]
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project