pr ch re R W
od an gis EG AR
uc ce te I
t— to r o ST RA
ww w nlin RA NT
w. in a e TI Y
tri F tod O
pp R a N
lit EE y f :
e. T or
co rip a
m p
/w Li
ar te
ra
nt
y
Owner’s Manual
VGA Over Cat5 Extenders
and Extender/Splitters
Extender Kit Models: B130-101, B130-101A,
B130-101-WP-1, B130-101A-WP-1,
B130-101S, B130-111, B130-111A and B130-101-U
Local Unit Models: B132-002-1,
B132-002A, B132-004-1 and B132-004A
Remote Unit Models: B132-100-1, B132-100A,
B132-100-WP-1, B132-100A-WP-1,
B132-110 and B132-110A
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2011 Tripp Lite. All rights reserved. SmartRack is a trademark of Tripp Lite.
201105276 933064-EN.indd 1
1
6/17/2011 12:24:16 PM
Table of Contents
Package Contents
3
Product Features
4
All
4
B130-1014
B130-101A4
B130-101-WP-14
B130-101A-WP-15
B130-101S5
B130-1115
B130-111A6
B130-101-U6
B132-002-16
B132-002A6
B132-004-17
B132-004A7
B132-100-18
B132-100A8
B132-100-WP-18
B132-100A-WP-18
B132-1109
B132-110A9
Optional Accessories
10
Mounting Hardware Instructions
11
Installation12
Extender Kit Installation
12
Non-Kit Standard Installation
14
Non-Kit Daisychain Installation
16
Extender/Repeater Kit Installation
18
Non-Kit Remote/Repeater Installation
20
Non-Kit Daisychain Remote/Repeater Installation 24
Warranty27
201105276 933064-EN.indd 2
2
6/17/2011 12:24:16 PM
B130-101
B130-101A
B130-101-WP-1
B130-101A-WP-1
B130-101S
B130-111
B130-111A
B130-101-U
B132-002-1
B132-002A
B132-004-1
B132-004A
B132-100-1
B132-100A
B132-100-WP-1
B132-100A-WP-1
B132-110
B132-110A
Package Contents
Local Unit (L), Remote
Unit (R) or Both (B)
1 or 2 External Power
Supplies (Input: 100240V, 50/60Hz, 0.5A
Output: 5V, 2A)
Mounting Hardware
Wallplate Screws
Screwdriver
3.5mm Male to DB9 Male
Adapter Cable
3.5mm Male to DB9
Female Adapter Cable
1 ft. VGA Splitter Cable
1 ft. VGA + Audio Splitter
Cable
1 ft. VGA Daisychain Cable
1 ft. VGA + Audio
Daisychain Cable
201105276 933064-EN.indd 3
B B B B B B B B L L L L R R R R R R
2 2 2 2 2 2 2 0 1 1 1 1 1 1 1 1 1 1
X X
X X X
X X X X X X
X X
X X
X X
X X X X X X X X
X X X X X X
X
X
X
X
X
X
3
6/17/2011 12:24:16 PM
Product Features
All
•Support a maximum resolution of 1920 x 1440 @ 60Hz.
•All operating systems supported.
•Plug and play; no software or drivers required.
•HDCP compliant.
B130-101
• Extends a VGA Video signal (1024 x 768 @ 60Hz) up to 1,000 ft. from
the source.
• Features an additional VGA port, allowing for the connection of a local
monitor.
• Includes mounting hardware that allows units to be wall-mounted,
rackmounted or pole mounted.
• Features built-in equalization and gain controls to adjust the video image.
B130-101A
• Extends both a VGA Video (1024 x 768 @ 60Hz) and a Stereo audio
signal up to 1,000 ft. from the source.
• Features additional VGA and 3.5mm ports, allowing for the connection
of a local monitor and speakers.
• Includes mounting hardware that allows units to be wall-mounted,
rackmounted or pole mounted.
• Features built-in equalization and gain controls to adjust the video image.
B130-101-WP-1
• Extends a VGA Video signal (1024 x 768 @ 60Hz) up to 1,000 ft. from
the source.
• Includes a VGA splitter cable, which allows for the connection of a local
monitor.
• Includes RJ45 jacks, allowing for easy connection via standard patch
cables; no 110 punchdown connections required.
• Features built-in equalization and gain controls to adjust the video image.
201105276 933064-EN.indd 4
4
6/17/2011 12:24:16 PM
Product Features
continued
B130-101A-WP-1
• Extends both a VGA Video (1024 x 768 @ 60Hz) and a Stereo audio signal
up to 1,000 ft. from the source.
• Includes a VGA + Audio splitter cable, which allows for the connection of a
local monitor and speakers.
• All wallplate units come with RJ45 jacks, allowing for easy connection via
standard patch cables; no 110 punchdown connections required.
• Features built-in equalization and gain controls to adjust the video image.
B130-101S
• Extends both a VGA Video (1024 x 768 @ 60Hz) and RS232 Serial signal
up to 1,000 ft. from the source.
• Includes mounting hardware that allows units to be wall-mounted,
rackmounted or pole mounted.
• Features built-in equalization and gain controls to adjust the video image.
B130-111
•Kit comes with both local transmitter and remote/repeater units.
•Locate multiple monitors at different points in a chain of up to 2,000 ft. by
connecting an additional remote receiver unit (B132-100-1 or B132-100WP-1), or a remote/repeater unit (B132-110).
•Up to 4 remote units (3 remote/repeaters and 1 receiver) can be connected
together, providing video to up to 4 remote displays in a full chain.
•Extend a 1024 x 768 (60Hz) signal up to 1,000 ft. between the local
transmitter and the first remote/repeater unit in the installation.
•Extend a 1024 x 768 (60Hz) signal up to an additional 1,000 ft. from
the first remote/repeater unit to the last display in the installation, for a
maximum extension distance of 2,000 ft..
•Local unit includes an additional VGA port, allowing for the connection of a
local monitor.
•Features built-in Equalization and Gain controls to adjust the video image.
•Includes mounting hardware that allows units to be wall-mounted,
rackmounted or pole mounted.
5
201105276 933064-EN.indd 5
6/17/2011 12:24:17 PM
Product Features
continued
B130-111A
•Kit comes with both local transmitter and remote/repeater units.
•Locate multiple monitors/speakers at different points in a chain of up to
2,000 ft. by connecting an additional remote receiver unit (B132-100A or
B132-100A-WP-1), or a remote/repeater unit (B132-110A).
•Up to 4 remote units (3 remote/repeaters and 1 receiver) can be connected
together, providing audio/video to up to 4 remote displays/speakers in a full
chain.
•Extend a 1024 x 768 (60Hz) video and stereo audio signal up to 1,000
ft. between the local transmitter and the first remote/repeater unit in the
installation.
•Extend a 1024 x 768 (60Hz) video and stereo audio signal up to an
additional 1,000 ft. from the first remote/repeater unit to the last set of
display and speakers in the installation, for a maximum extension distance
of 2,000 ft..
•Local unit includes additional VGA video and 3.5mm audio ports, allowing
for the connection of a local monitor and speakers.
•Features built-in Equalization and Gain controls to adjust the video image.
•Includes mounting hardware that allows units to be wall-mounted,
rackmounted or pole mounted.
B130-101-U
•Extends a VGA Video signal (1024 x 768 @ 60Hz) up to 500 ft. from the
source.
•Power is supplied by the USB connection on the local transmitter unit; no
external power supplies are required.
•Dongle-style local and remote units come with built-in VGA connectors; no
external VGA cables are required.
•Features built-in equalization and gain controls to adjust the video image.
201105276 933064-EN.indd 6
6
6/17/2011 12:24:17 PM
Product Features
continued
B132-002-1
• Works with the B132-100-1 and B132-100-WP-1 remote units to extend a
VGA Video signal (1024 x 768 @ 60Hz) up to 1,000 ft. from the source.
• Able to transmit a single VGA Video signal to 2 monitors.
• Includes mounting hardware that allows unit to be wall-mounted,
rackmounted or pole mounted.
B132-002A
• Works with the B132-100A and B132-100A-WP-1 remote units to extend
both a VGA Video (1024 x 768 @ 60Hz) and a Stereo audio signal up to
1,000 ft. from the source.
• Transmits a single VGA Video and Stereo audio signal to 2 sets of monitors
and speakers.
• Includes mounting hardware that allows unit to be wall-mounted,
rackmounted or pole mounted.
B132-004-1
• Features an additional VGA port, allowing for the connection of a local
monitor.
• Works with the B132-100-1 and B132-100-WP-1 remote units to extend a
VGA Video signal (1024 x 768 @ 60Hz) up to 1,000 ft. from the source.
• Able to transmit up to 5 (4 remote, 1 local) VGA Video signals.
• Expand the number of connected monitors to up to 25 (24 remote, 1 local)
by daisychaining up to 6 local units together.
Note: B132-002-1 local units cannot be daisychained.
• Includes mounting hardware that allows unit to be wall-mounted,
rackmounted or pole mounted.
• Up to three local units can be connected to a Tripp Lite B132-004-RB
rackmount bracket and mounted in just 1U of rack space.
201105276 933064-EN.indd 7
7
6/17/2011 12:24:17 PM
Product Features
continued
B132-004A
• Works with the B132-100A and B132-100A-WP-1 remote units to extend
both a VGA Video (1024 x 768 @ 60Hz) and a Stereo audio signal up to
1,000 ft. from the source.
• Features additional VGA and 3.5mm ports, allowing for the connection of a
local monitor and speakers.
• Transmits a single VGA Video and Stereo audio signal to up to 5 sets (4
remote, 1 local) of monitors and speakers.
• Expand the number of connected monitors/speakers to up to 25 (24
remote, 1 local) by daisychaining up to 6 local units together.
Note: B132-002A local units cannot be daisychained.
• Includes mounting hardware that allows unit to be wall-mounted,
rackmounted or pole mounted.
• Up to three local units can be connected to a Tripp Lite B132-004-RB
rackmount bracket and mounted in just 1U of rack space.
B132-100-1
• Includes mounting hardware that allows unit to be wall-mounted,
rackmounted or pole mounted.
• Features built-in equalization and gain controls to adjust the video image.
B132-100A
• Includes mounting hardware that allows unit to be wall-mounted,
rackmounted or pole mounted.
• Features built-in equalization and gain controls to adjust the video image.
B132-100-WP-1
• Includes RJ45 jacks, allowing for easy connection via standard patch cables;
no 110 punchdown connections required.
• Features built-in equalization and gain controls to adjust the video image.
B132-100A-WP-1
• Includes RJ45 jacks, allowing for easy connection via standard patch cables;
no 110 punchdown connections required.
• Features built-in equalization and gain controls to adjust the video image.
8
201105276 933064-EN.indd 8
6/17/2011 12:24:17 PM
Product Features
continued
B132-110
•Both extends and expands your Tripp Lite VGA over Cat5 installation,
allowing you to locate multiple monitors at different points in a chain of up
to 2,000 ft..
•Up to 4 remote units (3 remote/repeaters and 1 receiver) can be connected
together, providing video to up to 4 remote displays in a full chain.
•Extend a 1024 x 768 (60Hz) signal up to 1,000 ft. between the local
transmitter and the first remote/repeater unit in the installation.
•Extend a 1024 x 768 (60Hz) signal up to an additional 1,000 ft. from
the first remote/repeater unit to the last display in the installation, for a
maximum extension distance of 2,000 ft..
•Features built-in Equalization and Gain controls to adjust the video image.
•Includes mounting hardware that allows unit to be wall-mounted,
rackmounted or pole mounted.
B132-110A
•Both extends and expands your Tripp Lite VGA + Audio over Cat5
installation, allowing you to locate multiple monitors/speakers at different
points in a chain of up to 2,000 ft..
•Up to 4 remote units (3 remote/repeaters and 1 receiver) can be connected
together, providing audio/video to up to 4 remote displays/speakers in a full
chain.
•Extend a 1024 x 768 (60Hz) video and stereo audio signal up to 1,000
ft. between the local transmitter and the first remote/repeater unit in the
installation.
•Extend a 1024 x 768 (60Hz) video and stereo audio signal up to an
additional 1,000 ft. from the first remote/repeater unit to the last set of
display and speakers in the installation, for a maximum extension distance
of 2,000 ft..
•Features built-in Equalization and Gain controls to adjust the video image.
•Includes mounting hardware that allows unit to be wall-mounted,
rackmounted or pole mounted.
201105276 933064-EN.indd 9
9
6/17/2011 12:24:17 PM
Optional Accessories
• B132-004-RB 1U Rackmount Bracket
• N001-Series Cat5e Snagless Patch Cables
• N002-Series Cat5e Patch Cables
• N020-01K-GY Gray Cat5e Bulk Stranded Cable – 1,000 ft.
• N022-01K-GY Gray Cat5e Bulk 24Awg Solid Cable – 1,000 ft.
• N030-010 10 pk of RJ45 Plugs for Solid Wire Cat5e Cable
• N031-050 50 pk of RJ45 Plugs for Stranded Wire Cat5e Cable
• N201-Series Cat6 Snagless Patch Cables
• N202-Series Cat6 Snagless 24Awg Solid Patch Cables
• N222-01K-GY Gray Cat6 Bulk 24Awg Solid Cable – 1,000 ft.
• P312-Series Stereo Audio Cables
• P502-Series VGA Monitor Cables with RGB Coax
• P504-Series VGA Monitor + Stereo Audio Cables with RGB Coax
• P520-006 RS232 Serial Extension Cable – 6 ft.
• P524-01K Zero-Skew UTP Bulk Cable – 1,000 ft.
201105276 933064-EN.indd 10
10
6/17/2011 12:24:17 PM
Mounting Hardware Instructions
All of the non-wallplate VGA extender products come with mounting
hardware that allows them to be mounted in a variety of ways. The
following images show the different ways the included mounting brackets
can be attached for different mounting methods.
Note: The B132-004-1 and B132-004A can also be mounted to a Tripp Lite
B132-004-RB 1U rackmount bracket. Up to 3 B132-004-1 or B132-004A local
units can be connected to a B132-004-RB.
Wallmount
19” Rackmount
201105276 933064-EN.indd 11
Pole Mount
11
6/17/2011 12:24:18 PM
Installation
Extender Kit Installation (B130-101, B130-101A,
B130-101-WP-1, B130-101A-WP-1, B130-101S, B130-101-U)
Remote Unit
Local Unit
Note:
1. The diagram above shows a B130-101A VGA + Audio Extender Kit installation.
Installation will be the same for other extender kit models, with the exception of
units featuring VGA + Audio, VGA + RS232 serial or VGA only. The B130-101-U
gets power from the USB cable built-in to the local unit, and doesn’t require external
supplies.
2. Test to make sure the entire installation works properly before pulling cables through
ceilings/walls.
3. To achieve maximum distance and performance, 24Awg solid wire Cat5e/6 cable
must be used. The use of stranded wire Cat5e/6 cable, or cable with a gauge (Awg)
size higher than 24Awg, will result in shorter extension distance. All Tripp Lite N202Series cables are made with 24Awg solid wire cabling. Tripp Lite N022-01K-GY
(Cat5e) and N222-01K-GY (Cat6) are 24Awg solid wire bulk cables. For optimal
image quality between 500 and 1,000 ft., use Zero-Skew cable, such as Tripp Lite
P524-01K. For the B130-101-U, use Zero-Skew cable for distances between 250
and 500 ft.
4. To achieve maximum resolution, it is recommended that you use Tripp Lite P502Series VGA Video or P504-Series VGA Video and Stereo Audio cables with RGB coax.
*If this is a feature of your extender kit.
201105276 933064-EN.indd 12
12
6/17/2011 12:24:18 PM
Installation
continued
1 Make sure that the VGA, Stereo Audio* and RS232 Serial* source is
powered off.
2 (B130-101, B130-101A and B130-101S only) – Connect the VGA and
Stereo Audio* source to the INPUT port(s) on the local unit using a VGA
and Stereo Audio* cable.
3 (B130-101S only) – Connect the included 3.5mm Male to DB9 Female
adapter cable to the 3.5mm INPUT port on the local unit, and then
connect the computer to the adapter using a DB9 cable.
4 (B130-101-U only) – Connect the built-in VGA and USB connectors on
the local unit to the source computer.
5 (B130-101-WP-1 and B130-101A-WP-1 only) – If you wish to connect
a local monitor and speakers*, connect the male end of the included
splitter cable to the source port(s), and then connect one of the female
ends of the splitter cable to the INPUT port(s) on the local unit using a
VGA and Stereo Audio* cable. If you are not connecting a local monitor
and speakers*, connect the source directly to the INPUT port(s) on the
local unit.
6 (Optional) – Connect a local monitor and speakers* to the LOCAL port(s)
on the local unit, or the remaining female connector(s) on your splitter
cable*, using a VGA and Stereo Audio* cable.
Note: The B130-101S comes with a local video port only, and does not contain a
local RS-232 Serial port.
7 Connect the external power supply to the local unit, and then plug it
into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or
Uninterruptible Power Supply (UPS). The B130-101-U gets power from
the USB cable built-in to the local unit, and doesn’t require external power
supplies.
8 Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the local unit to
the RJ45 INPUT port on the remote unit.
9 (B130-101-U only) – Connect the built-in VGA connector on the remote
unit to the VGA port on a monitor.
*If this is a feature of your extender kit.
201105276 933064-EN.indd 13
13
6/17/2011 12:24:18 PM
Installation
continued
10 Connect a monitor and speakers* to the OUTPUT ports on the remote
unit using a VGA and Stereo Audio* cable.
11 (B130-101S only) – Connect the included 3.5mm Male to DB9 Male
adapter cable to the 3.5mm OUTPUT port on the remote unit, and then
connect the serial device to the adapter using a DB9 cable.
12 Connect the external power supply to the remote unit, and then plug
it into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or
Uninterruptible Power Supply (UPS). The B130-101-U gets power from
the USB cable built-in to the local unit, and doesn’t require external power
supplies.
13 Turn on the power to the monitor, speakers* and RS232 serial device.*
14 Turn on the power to the monitor, audio* and RS232 serial* source.
15 If necessary, adjust the Equalization and Gain controls using the included
screwdriver to improve the video image.
Note: The B130-101-U remote/receiver unit contains a switch that changes the
upper and lower limits of the Gain adjustment control depending on the length of
your installation. If using 50 ft. of Cat5e/6 cable or less, this setting should be L. If
over 50 ft., it should be set to H.
201105276 933064-EN.indd 14
14
6/17/2011 12:24:18 PM
Installation
continued
Non-Kit Standard Installation
B132-100A
Source PC
B132-004A B132-100A-WP-1
Note:
1. The diagram above shows a B132-004A VGA + Audio Extender/Splitter Kit
installation. Installation will be the same for non-Audio models, except that an Audio
source and speakers will not be connected.
2. Test to make sure the entire installation works properly before pulling cables through
ceilings/walls.
3. To achieve maximum distance and performance, 24Awg solid wire Cat5e/6 cable
must be used. The use of stranded wire Cat5e/6 cable, or cable with a gauge (Awg)
size higher than 24Awg, will result in shorter extension distance. All
Tripp Lite N202-Series cables are made with 24Awg solid wire cabling.
Tripp Lite N022-01K-GY (Cat5e) and N222-01K-GY (Cat6) are 24Awg solid wire bulk
cables. For optimal image quality between 500 and 1,000 ft., use Zero-Skew cable,
such as Tripp Lite P524-01K.
4. To achieve maximum resolution, it is recommended that you use Tripp Lite
P502-Series VGA Video or P504-Series VGA Video and Stereo Audio cables with RGB
coax.
201105276 933064-EN.indd 15
15
6/17/2011 12:24:19 PM
Installation
continued
1 Make sure that the VGA and Stereo Audio* source is powered off.
2 Connect the VGA and Stereo Audio* source to the INPUT port(s) on the
local unit (B132-002-1, B132-002A, B132-004-1 or B132-004A) using
a VGA and Stereo Audio* cable.
3 (Optional – B132-004-1 and B132-004A only) – Connect a local
monitor and speakers* to the LOCAL port(s) on the B132-004-1 or
B132-004A local unit.
4 Connect the external power supply to the local unit, and then plug it
into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or
Uninterruptible Power Supply (UPS).
5 Using Cat5e/6 cable, connect an available RJ45 OUTPUT port on the local
unit to the RJ45 INPUT port on a remote unit (B132-100-1, B132-100A,
B132-100-WP-1 or B132-100A-WP-1).
6 Repeat step 5 for each remote unit you are connecting to the installation.
7 Connect a monitor and speakers* to the OUTPUT port(s) on the remote
unit using a VGA and Stereo Audio* cable.
8 Repeat step 7 for each remote unit in the installation.
9 Connect the external power supply to the remote unit, and then plug
it into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or
Uninterruptible Power Supply (UPS).
10 Repeat step 9 for each remote unit in the installation.
11 Turn on the power to the monitor and speakers.*
12 Turn on the power to the monitor and audio* source.
13 If necessary, adjust the Equalization and Gain controls using the included
screwdriver to improve the video image.
*If this is a feature of your extender kit.
201105276 933064-EN.indd 16
16
6/17/2011 12:24:19 PM
Installation
continued
Non-Kit Daisychain Installation
(B132-004-1 and B132-004A only)
Source PC
Local PC and
Speakers (Optional)
B132-100A
B132-100A-WP-1
B132-004A
Note:
1. The diagram above shows a B132-004A VGA + Audio Extender/Splitter Kit daisychain
installation. Installation will be the same for non-Audio models, except that an Audio
source and speakers will not be connected.
2. Test to make sure the entire installation works properly before pulling cables through
ceilings/walls.
3. To achieve maximum distance and performance, 24Awg solid wire Cat5e/6 cable
must be used. The use of stranded wire Cat5e/6 cable, or cable with a gauge (Awg)
size higher than 24Awg, will result in shorter extension distance. All
Tripp Lite N202-Series cables are made with 24Awg solid wire cabling.
Tripp Lite N022-01K-GY (Cat5e) and N222-01K-GY (Cat6) are 24Awg solid wire bulk
cables. For optimal image quality between 500 and 1,000 ft., use Zero-Skew cable,
such as Tripp Lite P524-01K.
4. To achieve maximum resolution, it is recommended that you use Tripp Lite
P502-Series VGA Video or P504-Series VGA Video and Stereo Audio cables with RGB
coax.
201105276 933064-EN.indd 17
17
6/17/2011 12:24:19 PM
Installation
continued
1 Make sure that the VGA and Stereo Audio* source is powered off.
2 Connect the VGA and Stereo Audio* source to the INPUT port(s) on the
local unit (B132-004-1 or B132-004A) using a VGA and Stereo Audio*
cable.
3 Using the included daisychain cable, connect the LOCAL port(s) on the
B132-004-1 or B132-004A to the INPUT ports on a second level B132004-1 or B132-004A.
Note: A standard VGA cable can be used to increase the distance between units
with no more than 6 ft. between.
4 Repeat step 3 for each additional local unit you are adding to the
daisychain, with no more than 6 local units in the entire installation.
5 (Optional) – Connect a local monitor and speakers* to the LOCAL port(s)
of the last B132-004-1 or B132-004A in the daisychain using a VGA and
Stereo audio cable.
6 Connect the external power supply to the first local unit in the installation,
and then plug it into a Tripp Lite Surge Suppressor, Power Distribution Unit
(PDU) or Uninterruptible Power Supply (UPS).
7 Repeat step 6 for each additional local unit in the installation.
8 Using Cat5e/6 cable, connect an available RJ45 OUTPUT port on the local
unit to the RJ45 INPUT port on a remote unit (B132-100-1, B132-100A,
B132-100-WP-1 or B132-100A-WP-1).
9 Repeat step 8 for each remote unit you are connecting to the installation.
10 Connect a monitor and speakers* to the OUTPUT ports on the remote
unit using a VGA and Stereo Audio* cable.
11 Repeat step 10 for each remote unit in the installation.
12 Connect the external power supply to the remote unit, and then plug
it into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or
Uninterruptible Power Supply (UPS).
13 Repeat step 12 for each remote unit in the installation.
14 Turn on the power to the monitor and speakers.*
15 Turn on the power to the monitor and audio* source.
16 If necessary, adjust the Equalization and Gain controls using the included
screwdriver to improve the video image.
*If this is a feature of your extender kit.
18
201105276 933064-EN.indd 18
6/17/2011 12:24:19 PM
Installation
continued
Extender/Repeater Kit Installation
(B130-101. B130-101A, B130-111 and B130-111A)
Note:
1. An extender/repeater kit installation can start with a B130-101, B130-101A, B130111 or B130-111A. The only difference between these kits is the type of remote unit
that comes with them. The B130-101 and B130-101A come with remote receiver
units, and the B130-111 and B130-111A come with remote/repeater units.
2. The diagram above shows a B130-111A installation, with the maximum number of
remote units connected. Installation will be the same for the B130-111, except there
will be no audio connections. Installation will be the same for the B130-101 and
B130-101A, except that instead of adding remote units to the end of the installation,
remote/repeater units will be inserted in between the local and remote units that
come with the kits.
3. A 1024 x 768 (60Hz) signal can be extended up to 1,000 ft. from the source to
the first remote/repeater unit in the installation. A 1024 x 768 (60Hz) signal can be
extended up to an additional 1,000 ft. between the first remote/repeater unit and the
last display in the installation. Up to 4 remote units (3 remote/repeaters and 1 remote
receiver) can be connected together to transmit a signal to up 4 points in a 2,000 ft.
chain.
201105276 933064-EN.indd 19
19
6/17/2011 12:24:19 PM
Installation
continued
4. To achieve maximum distance and performance, 24Awg solid wire Cat5e/6 cable
must be used. The use of stranded wire Cat5e/6 cable, or cable with a gauge (AWG)
size higher than 24Awg, will result in shorter extension distance. All Tripp Lite N202Series cables are made with 24Awg solid wire cabling. Tripp Lite N022-01K-GY
(Cat5e) and N222-01K-GY (Cat6) are 24Awg solid wire bulk cables. For optimal
image quality between 500 and 1,000 ft., use Zero-Skew cable, such as Tripp Lite
P524-01K.
5. To achieve maximum distance and performance, it is recommended that you use
Tripp Lite P502-Seriess VGA Video or P504-Series VGA + Audio cables with RGB
coax.
6. Test to make sure the entire installation works properly before pulling cables through
ceilings/walls.
1 Make sure that the VGA Video and Stereo Audio* source is powered off.
2 Connect the VGA Video and Stereo Audio* source to the INPUT port(s) on
the local unit using a VGA and Stereo Audio* cable.
3 (Optional) – Connect a local monitor and speakers* to the LOCAL port(s)
on the local unit using a VGA Video and Stereo Audio* cable.
4 Connect the external power supply to the local unit, and then plug it
into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or
Uninterruptible Power Supply (UPS). The Red power LED and the Green
RJ45 LED will illuminate to indicate the unit is receiving power.
5 Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the local unit to
the RJ45 INPUT port on the remote/repeater unit.
Note: If starting with a B130-101 or B130-101A, a remote/repeater unit
(B132-110 or B132-110A) must be added in between the local and remote units
that come with the kit.
6 Connect a monitor and speakers* to the OUTPUT port(s) on the remote/
repeater unit using a VGA Video and Stereo Audio* cable.
7 Connect the external power supply to the remote/repeater unit, and then
plug it into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or
Uninterruptible Power Supply (UPS). The Red power LED and the Green
RJ45 LEDs illuminate to indicate the unit is receiving power.
*If this is a feature of your extender kit.
201105276 933064-EN.indd 20
20
6/17/2011 12:24:19 PM
Installation
continued
If you are not connecting any additional remote/repeater units, proceed to
step 12.
8 Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the first remote/
repeater unit to the RJ45 INPUT port on a second remote/repeater unit.
Note: If starting with a B130-101 or B130-101A, a remote/repeater unit
(B132-110 or B132-110A) must be added in between the local and remote units
that come with the kit.
9 On the remote/repeater unit you just added, connect a monitor and
speakers* to the OUTPUT port(s) using a VGA Video and Stereo Audio*
cable.
10 Connect the external power supply to the remote/repeater unit, and then
plug it into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or
Uninterruptible Power Supply (UPS). The Red power LED and the Green
RJ45 LEDs illuminate to indicate the unit is receiving power.
11 Repeat steps 8 through 10 for each additional unit you are connecting,
with no more than 4 in a chain. The last remote unit in an extender/
repeater installation should be a standard B132-100-1, B132-100WP-1, B132-100A or B132-100A-WP-1 receiver. When starting with a
B130-101 or B130-101A kit, the included remote receiver can be the
last unit in the chain.
12 Turn on the power to the connected monitors and speakers.*
13 Turn on the power to the VGA Video and Stereo Audio* source. The
Orange RJ45 LEDs will illuminate to indicate that the units are receiving a
signal from the source.
14 If necessary, use the included screwdriver to adjust the Equalization and
Gain settings on the remote/repeater units to improve the video image.
*If this is a feature of your extender kit.
201105276 933064-EN.indd 21
21
6/17/2011 12:24:20 PM
Installation
continued
Non-Kit Remote/Repeater Installation
Note:
1. The diagram above shows a B132-004-1 installation with the maximum number of
remote units connected. A B132-004A installation will be the same, except there will
be audio connections. B132-002-1 and B132-002A local units come with 2 ports
instead of 4, and do not feature additional ports for a local monitor and speakers.*
2. A 1024 x 768 (60Hz) signal can be extended up to 1,000 ft. between the local
transmitter and the first remote/repeater unit in the installation. Up to an additional
1,000 ft. can be placed in between the first remote/repeater unit and the last display
in the installation, for a maximum extension distance of 2,000 ft. Up to 4 remote
units (3 remote/repeaters and 1 receiver) can be connected together to transmit a
signal to up to 4 points in a 2,000 ft. chain.
3. Test to make sure the entire installation works properly before pulling cables through
ceilings/walls.
*If this is a feature of your extender kit.
201105276 933064-EN.indd 22
22
6/17/2011 12:24:20 PM
Installation
continued
4. To achieve maximum distance and performance, 24Awg solid wire Cat5e/6 cable
must be used. The use of stranded wire Cat5e/6 cable, or cable with a gauge (AWG)
size higher than 24Awg, will result in shorter extension distance. All Tripp Lite N202Series cables are made with 24Awg solid wire cabling. Tripp Lite N022-01K-GY
(Cat5e) and N222-01K-GY (Cat6) are 24Awg solid wire bulk cables. For optimal
image quality between 500 and 1,000 ft., use Zero-Skew cable, such as
Tripp Lite P524-01K.
5. To achieve maximum distance and performance, it is recommended that you use
Tripp Lite P502-Seriess VGA Video or P504-Series VGA + Audio cables with RGB
coax.
1 Make sure that the VGA Video and Stereo Audio* source is powered off.
2 Connect the VGA Video and Stereo Audio* source to the INPUT port(s) on
the local unit.
3 (Optional – B132-004-1 and B132-004A only) – Connect a local
monitor and speakers* to the LOCAL port(s) on the local unit using a VGA
Video and Stereo Audio* cable.
4 Connect the external power supply to the local unit, and then plug it
into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or
Uninterruptible Power Supply (UPS). The Red power LED and the Green
RJ45 LEDs will illuminate to indicate the unit is receiving power.
5 Using Cat5e/6 cable, connect an available RJ45 OUTPUT port on the local
unit to the RJ45 INPUT port on the remote/repeater unit. (B132-110 or
B132-110A)
6 Connect a monitor and speakers* to the OUTPUT port(s) on the remote/
repeater unit using a VGA Video and Stereo Audio* cable.
7 Connect the external power supply to the remote/repeater unit, and then
plug it into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or
Uninterruptible Power Supply (UPS). The Red power LED and the Green
RJ45 LEDs illuminate to indicate the unit is receiving power.
If you are not connecting any additional remote/repeater units, proceed to
step 12.
*If this is a feature of your extender kit.
201105276 933064-EN.indd 23
23
6/17/2011 12:24:20 PM
Installation
continued
8 Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the first remote/
repeater unit to the RJ45 INPUT port on a second remote/repeater unit.
9 On the remote/repeater unit you just added, connect a monitor and
speakers* to the OUTPUT port(s) using a VGA Video and Stereo Audio*
cable.
10 Connect the external power supply to the remote/repeater unit, and then
plug it into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or
Uninterruptible Power Supply (UPS). The Red power LED and the Green
RJ45 LEDs illuminate to indicate the unit is receiving power.
11 Repeat steps 8 through 10 for each additional unit you are connecting,
with no more than 4 in a chain. The last remote unit in the installation
should be a standard B132-100-1, B132-100-WP-1, B132-100A or
B132-100A-WP-1 receiver.
12 Repeat steps 5 through 10 for each additional local unit port that you are
adding remote/repeater units to, with no more than 4 levels per port.
13 Turn on the power to the connected monitors and speakers.*
14 Turn on the power to the VGA Video and Stereo Audio* source. The
Orange RJ45 LEDs will illuminate to indicate that the units are receiving a
signal from the source.
15 If necessary, use the included screwdriver to adjust the Equalization and
Gain settings on the remote/repeater units to improve the video image.
*If this is a feature of your extender kit.
201105276 933064-EN.indd 24
24
6/17/2011 12:24:20 PM
Installation
continued
Non-Kit Daisychain Remote/Repeater Installation
(B132-004A and B132-004-1 only)
Note:
1. The diagram above shows a B132-004A installation with the maximum number of
remote units connected. A B132-004 installation will be the same, except there
will be no audio connections. B132-002-1 and B132-002A local units cannot be
daisychained.
201105276 933064-EN.indd 25
25
6/17/2011 12:24:21 PM
Installation
continued
2. A 1024 x 768 (60Hz) signal can be extended up to 1,000 ft. between the local
transmitter and the first remote/repeater unit in the installation. Up to an additional
1,000 ft. can be placed in between the first remote/repeater unit and the last display
in the installation, for a maximum extension distance of 2,000 ft. Up to 4 remote
units (3 remote/repeaters and 1 receiver) can be connected together to transmit a
signal to up to 4 points in a 2,000 ft. chain.
3. Test to make sure the entire installation works properly before pulling cables through
ceilings/walls.
4. To achieve maximum distance and performance, 24Awg solid wire Cat5e/6 cable
must be used. The use of stranded wire Cat5e/6 cable, or cable with a gauge (AWG)
size higher than 24Awg, will result in shorter extension distance. All Tripp Lite N202Series cables are made with 24Awg solid wire cabling. Tripp Lite N022-01K-GY
(Cat5e) and N222-01K-GY (Cat6) are 24Awg solid wire bulk cables. For optimal
image quality between 500 and 1,000 ft., use Zero-Skew cable, such as
Tripp Lite P524-01K.
5. To achieve maximum distance and performance, it is recommended that you use
Tripp Lite P502-Seriess VGA Video or P504-Series VGA + Audio cables with RGB
coax.
1 Make sure that the VGA Video and Stereo Audio* source is powered off.
2 Connect the VGA Video and Stereo Audio* source to the INPUT port(s) on
the local unit using a VGA Video and Stereo Audio* cable.
3 Using the included daisychain cable, connect the LOCAL port(s) on the
local unit to the INPUT ports on a second level local unit.
Note: A standard VGA cable can be used to increase the distance between units
with no more than 6 ft. between.
4 Repeat step 3 for each additional local unit you are adding to the
daisychain, with no more than 6 local units in the entire installation.
5 (Optional) – Connect a local monitor and speakers* to the LOCAL port(s)
of the last local unit in the daisychain using a VGA Video and Stereo
Audio* cable.
6 Connect the external power supply to the first local unit in the installation,
and then plug it into a Tripp Lite Surge Suppressor, Power Distribution Unit
(PDU) or Uninterruptible Power Supply (UPS). The Red power LED and the
Green RJ45 LEDs will illuminate to indicate the unit is receiving power.
*If this is a feature of your extender kit.
201105276 933064-EN.indd 26
26
6/17/2011 12:24:21 PM
Installation
continued
7 Repeat step 6 for each additional local unit in the installation.
8 Using Cat5e/6 cable, connect an available RJ45 OUTPUT port on the local
unit to the RJ45 INPUT port on the remote/repeater unit. (B132-110 or
B132-110A)
9 Connect a monitor and speakers* to the OUTPUT port(s) on the remote/
repeater unit using a VGA Video and Stereo Audio* cable.
10 Connect the external power supply to the remote/repeater unit, and then
plug it into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or
Uninterruptible Power Supply (UPS). The Red power LED and the Green
RJ45 LEDs illuminate to indicate the unit is receiving power.
If you are not connecting any additional remote/repeater units, proceed to
step 15.
11 Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the first remote/
repeater unit to the RJ45 INPUT port on a second remote/repeater unit.
12 On the remote/repeater unit you just added, connect a monitor and
speakers* to the OUTPUT port(s) using a VGA Video and Stereo Audio*
cable.
13 Connect the external power supply to the remote/repeater unit, and then
plug it into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or
Uninterruptible Power Supply (UPS). The Red power LED and the Green
RJ45 LEDs illuminate to indicate the unit is receiving power.
14 Repeat steps 11 through 13 for each additional unit you are connecting,
with no more than 4 in a chain. The last remote unit in the installation
should be a standard B132-100-1, B132-100-WP-1, B132-100A or
B132-100A-WP-1 receiver.
15 Repeat steps 8 through 14 for each additional local unit port that you are
adding remote/repeater units to, with no more than 4 levels per port.
16 Turn on the power to the connected monitors and speakers.*
17 Turn on the power to the VGA Video and Stereo Audio* source. The
Orange RJ45 LEDs will illuminate to indicate that the units are receiving a
signal from the source.
18 If necessary, use the included screwdriver to adjust the Equalization and
Gain settings on the remote/repeater units to improve the video image.
*If this is a feature of your extender kit.
201105276 933064-EN.indd 27
27
6/17/2011 12:24:21 PM
Warranty
1-Year Limited Warranty
TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one
(1) year from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited to repairing
or replacing (at its sole option) any such defective products. To obtain service under this warranty, you
must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or an authorized TRIPP LITE
service center. Products must be returned to TRIPP LITE or an authorized TRIPP LITE service center with
transportation charges prepaid and must be accompanied by a brief description of the problem encountered
and proof of date and place of purchase. This warranty does not apply to equipment which has been
damaged by accident, negligence or misapplication or has been altered or modified in any way.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid
limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS
PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Specifically, TRIPP LITE is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of
use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.
WARNING
Use of this equipment in life support applications where failure of this equipment can reasonably
be expected to cause the failure of the life support equipment or to significantly affect its safety
or effectiveness is not recommended. Do not use this equipment in the presence of a flammable
anesthetic mixture with air, oxygen or nitrous oxide.
WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations,
when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:
• Send old equipment for recycling on a one-for-one, like-for-like basis
(this varies depending on the country)
• Send the new equipment back for recycling when this ultimately becomes waste
Warranty Registration
Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product.
You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Tripp Lite follows a policy of continuous improvement. Product specifi cations are subject to
change without notice.
201105276 933064-EN.indd 28
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
201105276 • 93-3064-EN
28
6/17/2011 12:24:21 PM