Chief RXF2 flat panel wall mount Installation Instructions
Add to my manuals12 Pages
Chief RXF2 is a universal fixed mount designed for installation on wood studs, concrete, concrete block, or brick walls. It can support displays weighing up to 175 lbs and features a kickstand that allows the display to tilt back 5 degrees for easy viewing. The RXF2 also has an adjustable center line to accommodate different display sizes and mounting hole patterns.
advertisement
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
RMF2
RLF2
RXF2
Universal Fixed Mounts
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
RMF2/RLF2/RXF2
RMF2/RLF2/RXF2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.
Installation Instructions
WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.
WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8" (1.6cm).
WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached does not exceed 125 lbs (56.7 kg) for the RMF2 and RLF2 or 175 lbs (79.4 kg) for the RXF2.
Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury.
DIMENSIONS - RMF2
419.1
16.50
400
15.75
MAX
-KICKSTAND LANYARDS
-WHEN KICKSTAND
IS ACTIVATED, THE
DISPLAY TILTS BACK 5
558.8
22.00
[449]
17.68
MAX
279.4
11.00
200
7.87
TOP MOUNTING
HOLE TO CENTERLINE
ARROW ON THE
WALL PLATE
177.8
7.00
WALL PLATE
OPENING
63.5
2.50
CENTERLINE
TO BOTTOM OF
WALL PLATE
OPENING
7.1
.28
HOLE SIZE
FOR LOCK
20.1
.79
(UP TO 1.54
USING SPACERS)
8.7
.34
ORIENTATION
AND CENTERLINE
NOTCHES
DETAIL A
SCALE 1 : 2
WALL PLATE
OPENING
25.4
1.00
212.7
8.38
CENTERLINE
DIAMOND
DETAIL B
SCALE 1 : 2
2
Installation Instructions
DIMENSIONS - RLF2
RMF2/RLF2/RXF2
419.1
16.50
400
15.75
MAX
-KICKSTAND LANYARDS
-WHEN KICKSTAND
IS ACTIVATED, THE
DISPLAY TILTS BACK 5
781.1
30.75
[670]
26.38
MAX
390.5
15.38
200
7.87
TOP MOUNTING
HOLE TO CENTERLINE
ARROW ON THE
WALL PLATE
177.8
7.00
WALL PLATE
OPENING
20.1
.79
(UP TO 1.54
USING SPACERS)
8.7
.34
63.5
2.50
CENTERLINE
TO BOTTOM OF
WALL PLATE
OPENING
7.1
.28
HOLE SIZE
FOR LOCK
ORIENTATION
AND CENTERLINE
NOTCHES
DETAIL A
SCALE 1 : 2
WALL PLATE
OPENING
25.4
1.00
212.7
8.38
CENTERLINE
DIAMOND
DETAIL B
SCALE 1 : 2
DIMENSIONS - RXF2
500
19.69
MAX
[965.2]
38.00
MAX
965.2
38.00
482.6
19.00
-KICKSTAND LANYARDS
-WHEN KICKSTAND
IS ACTIVATED, THE
DISPLAY TILTS BACK 5
200
7.87
TOP MOUNTING
HOLE TO CENTERLINE
ARROW ON THE
WALL PLATE
177.8
7.00
WALL PLATE
OPENING
20.1
.79
(UP TO 1.54
USING SPACERS)
8.7
.34
63.5
2.50
CENTERLINE
TO BOTTOM OF
WALL PLATE
OPENING
7.1
.28
HOLE SIZE
FOR LOCK
ORIENTATION
AND CENTERLINE
NOTCHES
DETAIL A
SCALE 1 : 2
WALL PLATE
OPENING
25.4
1.00
CENTERLINE
DIAMOND
212.7
8.38
DETAIL B
SCALE 1 : 2
3
RMF2/RLF2/RXF2
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
4
Installation Instructions
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
RMF2/RLF2/RXF2
TOOLS REQUIRED FOR INSTALLATION
Installation Instructions
PARTS
7/32" (5.5mm)
5/16" (7.9mm)
1/2" (12.7mm) #2
5
B(2)
[vertical bracket]
For below kit, quantities are 4 for RMF2 and
RLF2, 6 for RXF2 F (1)
Hardware Bag
A(1)
[wall plate]
[RLF2 shown]
C(4 or 6)
5/16 x 2 1/2"
FA(8)
M4 x 16mm
FE(6)
M5 x 16mm
FI(6)
M6 x 16mm
FL(6)
M8 x 20mm
FP(8)
1/4"(6.4mm)
D(4 or 6)
1/4" (6.4mm)
E(4 or 6)
[concrete anchor]
FB(6)
M4 x 20mm
FC(6)
M4 x 25mm
FF(6)
M5 x 20mm
FG(6)
M5 x 25mm
FJ(6)
M6 x 25mm
FK(6)
M6 x 35mm
FM(6)
M8 x 30mm
FQ(8)
1/2"(12.7mm)
FN(6)
M8 x 40mm
FD(6)
M4 x 35mm
FH(6)
M5 x 35mm
FO(6)
M8 x 50mm
FS(8)
[universal washer]
RMF2/RLF2/RXF2
Assembly And Installation
Install Wall Plate to Wall - Wood Studs
WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8" (1.6cm).
1.
Unfold wall plate (A) to prepare it for mounting to wall. (See
Figure 1)
Installation Instructions
2
3 x 4 or 6
1
(A)
Figure 2
2 x 24"
2 x 16"
1
Figure 1
2.
Level wall plate (A) and mark locations of pilot holes.(See
Figure 2)
NOTE: The RMF2 must be installed on two 16" studs. The
RLF2 can be installed on 16" studs (inner holes) or 24" studs (outer holes). For the RXF2, it can be mounted over two or three 16" studs or two 24" studs. If mounting to three 16" studs, it must be mounted to all three studs using the outer holes and center holes.
(See Figures 2 and 3)
NOTE: The vertical center of the display will be even with the center line indicated on the labels located directly below each hinge. Keep this in mind when determining mounting location. (See Figure 3)
3.
Drill 7/32" (5.5mm) diameter pilot holes into wood studs at marked locations. (See Figure 2)
3 x 16"
CENTER
LINE
Figure 3
4.
Install 5/16 x 2 1/2" hex head cap screws (C) through four flat washers (D), wall plate (A) and into wood studs. (See
Figure 4)
(D) x 4 or 6
4 (C) x 4 or 6
Figure 4
(A)
6
Installation Instructions
Install Wall Plate to Wall - Concrete,
Concrete Block or Brick
WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the component.
RMF2/RLF2/RXF2
3.
Drill 5/16" (7.9mm) diameter pilot holes into wall at marked locations. Holes must be drilled at least 2 1/2 inches deep.
(See Figure 5)
4.
Install four or six concrete anchors (E) into drilled holes. Use a hammer to tap anchors into holes. (See Figure 6)
4 (E) x 4 or 6
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free of electrical wires and cables before drilling or installing fasteners.
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of gas, water, waste, or any other plumbing before cutting, drilling, or installing fasteners.
1.
Unfold wall plate (A) to prepare it for mounting to wall. (See
Figure 1)
2.
Level wall plate (A) and mark locations of pilot holes at desired mounting location. (See Figure 5)
NOTE: For the RLF2, either the inner or outer four holes may be used.
NOTE: For the RXF2, use the outer four holes and the two middle holes on wall plate for installation.
NOTE: The vertical center of the display will be even with the center line indicated on the labels located directly below each hinge. Keep this in mind when determining mounting location. (See Figure 5)
Figure 6
5.
Using 1/2" (12.7mm) wrench, install screws (C) through flat washers (D), wall plate (A) and into concrete anchors (E).
(See Figure 7)
(D) x 4 or 6
(E) x 4 or 6
5 (C) x 4 or 6 (A)
2
3 x 4 or 6
Figure 7
CENTER
LINE
Figure 5
7
RMF2/RLF2/RXF2
Install Brackets to Display
WARNING: The minimum hole pattern size is 100mm x
100mm for the RMF2 and 200mm x 200mm for the RLF2 and the RXF2.
1.
Lay display face down on protective surface.
CAUTION: Using screws of improper diameter may damage your display! Proper screws will easily thread into display mounting holes.
2.
Select screw diameter by examining hardware (FA-FO)
(8mm, 6mm, 5mm, or 4mm) and comparing with mounting holes on display. (See Figure 8)
3.
Select spacers: (See Figure 8)
• If mounting holes are not recessed and both brackets (B) can lay flat against display, then no spacers are required.
• If mounting holes are recessed, or if protrusions prevent brackets (B) from laying flat, then spacers
(FP or FQ) must be used.
• If additional depth is needed behind display, spacers (FP and FQ) can be stacked on top of each other.
CAUTION: Using screws of improper length may damage your display! Proper screws will have adequate thread engagement without contacting bottom of display mounting holes.
4.
Select screw length: (See Figure 8)
• Using your hand, insert SHORTEST length screw of selected diameter (FA, FE, FI or FL) through bracket (B), universal washer (FS), selected spacer (FP or FQ, if required), into display mounting hole. Do NOT thread screw into hole at this time.
• Proper screw length requires base of screw head to protrude above flat washer a distance equal to
or greater than the screw diameter. If screw length is inadequate, select longer screw. Select
shortest screw which will protrude the required distance.
5.
Place brackets (B) on display, ensuring: (See Figure 8)
• Upper hooks are towards top of display.
• Center of brackets (B) are as close to the center of the back of display as possible after being installed. Center of bracket is indicated by the diamond-shaped hole.
6.
Using Phillips screwdriver, carefully install selected screws through universal washers (FS), brackets (B), and spacers
(FP or FQ, if required), into display. (See Figure 8)
7.
Tighten all screws. Ensure all applicable display mounting holes (4, 6, or 8) are used.
5
Installation Instructions
6
2 4
(non-recessed holes)
(FA-FO) x4,x6,x8
(FS) x4,x6,x8
6
(B) x 2
2 4
(recessed holes or extra depth needed)
(FA-FO) x4,x6,x8
(FS) x4,x6,x8
3 (FP or FQ)*
5
(B) x 2
*If additional depth is needed, spacers (FP or FQ) can be stacked on top of each other
Figure 8
8
Installation Instructions
Install Display to Wall Plate
WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached does not exceed 125 lbs (56.7 kg) for the RMF2 and RLF2 or 175 lbs (79.4 kg) for the RXF2.
Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury.
WARNING: Display may be very heavy! Ensure display can be safely lifted and maneuvered as required to install on wall plate. Failure to take adequate precautions can result in serious personal injury or damage to equipment!
WARNING: Interface brackets must be hung on opposite sides of the center tab on wall plate! (See Figure 9)
2
RMF2/RLF2/RXF2
(view from left side) kickstand engaged center tab
1
5 interface brackets must be hung on opposite sides of center tab
Figure 9
1.
Make sure interface brackets are in the kickstand position by pulling down on handles as far as possible. (See Figure
10)
2.
Hang display with brackets (B) on upper rail of wall plate (A).
Kickstand should be engaged with lower portion of wall plate. (See Figure 10)
Figure 10
NOTE: Any cable management or rear display adjustments should be made when the display is resting on the kickstand.
9
RMF2/RLF2/RXF2
(views from left side) kickstand against wall
3
6 locked position
4
Figure 11
3.
Unlock kickstand by pushing up on interface brackets until kickstand rests against the wall. (See Figure 11)
4.
Push up on the interface brackets further in order to lock display into position against wall. (See Figure 11)
5.
Straps can be tucked behind display on notch on interface brackets (B) after installation is complete so that they will not be visable to the viewer. (See Figure 9)
6.
(Optional) Route padlock or cable lock (not included) through bottom holes on interface bracket to provide additional security. (See Figure 11)
10
Installation Instructions
Installation Instructions RMF2/RLF2/RXF2
11
RMF2/RLF2/RXF2 Installation Instructions
Chief Manufacturing, a products division of Milestone AV Technologies
8800-002048 REV 00
2010 Milestone AV Technologies, a
Duchossois Group Company www.chiefmfg.com
01/10
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
Europe
F 877.894.6918 / 952.894.6918
A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
Asia Pacific
F +31 (0)40 2668615
A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Maximum weight capacity: 79.3 kg
- Wall
- Metal Black