XE-A206 Quick Start Guide
English
The following describes how to get the cash register ready for operate. Follow these steps before you use the cash register for the first time.
Before you set up the cash register, prepare three new alkaline batteries LR6 ("AA" size) which are necessary for memory backup. Find a stable and flat surface not subject to direct radiation, to place
the cash register.
1
3
Initializing the Cash Register
(for receipt printing)
If you want to use a paper roll for journal printing, please refer to GETTING
STARTED section of the instruction manual.
REG
OPX/Z
OFF
MA
To ensure the cash register operates properly, please use the following
procedure:
1. Make sure the power cord is unplugged and batteries are not
installed on the register.
2. Insert the manager (MA) key into the mode switch and turn it to the
REG position.
Installing the Paper Roll
VOID
PGM
MGR
X1/Z1
1. Lift up the print roller release lever to unlock and open the print roller arm.
3. Insert the plug of the power cord into the AC outlet. The buzzer will
sound three times.
IMPORTANT: This operation must be performed without batteries installed.
4. The cash register has now been initialized.
The register display will show “0.00” with “ ”.
Print roller arm
X2/Z2
Print roller release lever
2. Set a paper roll in the paper roll cradle as illustrated right.
To the printer
NOTE: When setting a new paper roll in the paper roll cradle, be sure to cut
the paper end behind the taped (or pasted) point in advance.
Correct
To the printer
Incorrect
2
Installing the Batteries
1. Push the printer cover forward and detach it.
3. Feed the end of the paper along with the paper positioning guides
as illustrated at the right.
Paper positioning
guides
2. Open the battery compartment cover next to the paper roll cradle.
4. While holding down the paper, slowly close the print roller arm, and
push down the arm until you hear a click locking the arm.
Make sure you securely push down the center of the wing part of the
arm as illustrated at the right. The paper will be fed automatically.
3. Install three new alkaline batteries LR6 (“AA” size) as shown at the
right. (Batteries are not supplied with the cash register.) Make sure
that positive (+) and negative (–) poles of each battery are properly
oriented.
5. Cut off the excess paper using the edge of the inner cover, and
replace the printer cover. Press the F key to make sure the paper
end comes out of the printer cover and clean paper appears.
4. When the batteries are properly installed, “ ” on the display will
disappear. Close the battery compartment cover.
NOTE: If the print roller arm is not securely locked, the unit will not print correctly.
If this problem occurs, open the arm, and close the arm as instructed
above.
4
5
Basic Programming
Set the mode switch to the PGM position.
Before Starting Entries
REG
OPX/Z
OFF
MGR
VOID
Now, you are ready!
• Set the mode switch to the REG position.
X1/Z1
X2/Z2
PGM
VOID
PGM
Setting the Date
Enter the date in 8 digits using the month-day-year format. Then press
Example: 02262010
Date (February 26, 2010)
REG
OPX/Z
OFF
MGR
X1/Z1
X2/Z2
s.
s
Registration Example (when selling department items by cash)
1. Enter your clerk code. (By default, clerk code 1 is assigned.)
1L
Clerk code
Setting the Time
Enter the time in 4 digits (“hhmm” format) using the 24 hour system. Then press s.
Example: 1430 s
Time (2:30 p.m.)
Setting Tax Rates (%)
NOTE: If you are in an area that uses a tax table for tax calculation, please refer to the programming
section in the instruction manual.
Specify a tax rate (%) for calculation of tax on each taxable subtotal using the following
sequence:
s ➔ 9 ➔ @ ➔ Tax number (1 to 4)* ➔ @ ➔ Tax rate (0.0000% to 100.0000%) ➔ @
➔ Minimum taxable amount (0.01 to 999.99) ➔ s ➔ A
(Smallest amount for which tax must be collected.)
*Up to 4 types of tax are programmable.
Example1: Set state tax 6.25% with tax exempt as 12¢
2. Enter the price for the first department item.
For example for 5.00, enter 5:, and press the appropriate 5:!
department key.
Price and dept. 1
For department 17 to department 32, press D first before 825D"
pressing the department key.
Price and dept. 18
For department 33 and above, enter the department code
using numeric keys, and press d, then enter the price and
press d again.
3. Repeat step 2 for all the department items.
4. Press s to display the amount due.
s
5. Enter the amount received from the customer. (You can omit 2:0
this step if the amount tendered is the same as the subtotal.) Amount tendered
6. Press A, and the change due is displayed (when the
A
amount received was not entered, total amount is displayed)
and the drawer is opened.
7. Tear off the receipt and give it to the customer with his or her
change.
8. Close the drawer.
s 9@ 1@ 6P25@ 12 s A
Tax 1
Tax rate (6.25%) Min. taxable
amount ($0.12)
Example2: Set state tax 4% with tax exempt as 0¢
s 9@ 1@ 4 s A
Tax 1
Tax rate (4%)
Other Programming
While the cash register is pre-programmed so it can be used with minimal set-up, it does provide
you optional features. For details, please refer to the instruction manual.
How to download Customer Support Tool:
Customer Support Tool can be downloaded from the Sharp web site.
Please visit the Sharp web site: http://www.sharpusa.com/registersoftware
Initial settings:
Department 1 to 10: Taxable 1
Department 11 to 99: Non-taxable
When an error occurs:
l
When an error occurs with an alarm sound, press
to clear the error. If you do not clear the error, press
The transaction will be finalized in subtotal void or cash sale.
Printed in China
E twice.
(TCADH2556RCZZ) 1