ENGLISH
MODEL
HT-SL50
SOUND BAR HOME THEATER SYSTEM
OPERATION MANUAL
Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read
this manual carefully. It will guide you in operating your SHARP product.
HT-SL50 Sound Bar Home Theater system consisting of Sound Bar and Subwoofer.
Notes:
● This product is recommended for flat panel TV (LCD and plasma).
● For HDMI connection, this product only supports PCM (Pulse Code Modulation) signals.
● This product is controlled via HDMI CEC (Consumer Electronics Control) specification, therefore
for HDMI connection, your TV’s CEC must be enabled.
● For TV without HDMI CEC, headphone or RCA (variable output) analog connection is available.
● For TV without HDMI, headphone or RCA (variable output) connection is required.
Recommended Connection:
CEC FUNCTION
CONNECTION
CONNECTION METHOD
with HDMI
( ver1.4 with ARC)
TV Type
MUST BE ENABLED
HDMI IN
(ARC)
Page 10, Method 1
with HDMI
MUST BE ENABLED
HDMI IN
Page 11, Method 2
HDMI TV without
CEC & ARC or non
HDMI TV
NONE
TINSZA935AWZZ
HT-SL50_Front EN.fm
HEADPHONE OUT
Page 12, Method 1
RCA
(VARIABLE OUT)
Page 12, Method 2
Printed in Malaysia
11C R AS 1
2011February24
Accessories
Please confirm that only the following accessories are included.
RCA to headphone cable
(1pin - 2 pins) x 1
(QCNWGA064AWPZ)
Subwoofer Stand x 2
(GITAUA004AW01)
Audio cable x 1
(QCNWGA062AWPZ)
HDMI cable x 1
(QCNWGA065AWPZ)
Foot cushion x 4
(PCUSGA189AWZZ)
Wall Mount Angle x 2
(LANGKA225AW01)
Pattern Paper
(TCAUHA026AWZZ)
Speaker Wire
(QCNWHA043AW01)
Sound bar Stand x 2
(GITAUA012AWSA)
Sound bar Stand
Cushion x 2
(PCUSSA190AWZZ)
Special Notes
NOTE
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and
receiver.
● Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV
technician for help.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
1
2
3
4
5
6
7
1
9
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
FOR YOUR RECORDS
For your assistance in reporting this unit in case of loss
or theft, please record below the model number and
serial number which are located on the rear of the unit.
Please retain this information.
Model number
Serial number
Date of purchase
Place of purchase
........................................................
........................................................
........................................................
........................................................
E-1
2011 February 24
HT-SL50
Special Notes (continued)
WARNING
FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by
the manufacturer could void the user’s authority to operate
this equipment.
ENERGY STAR® Program Information
Products that have earned
the ENERGY STAR® are
designed to protect the
environment through
superior energy efficiency.
ENERGY STAR® is a U.S. registered mark.
HDMI, the HDMI Logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other
countries.
Special Notes
Important Safety Instructions
Electricity is used to perform many useful functions, but it
can also cause personal injuries and property damage if
improperly handled. This product has been engineered
and manufactured with the highest priority on safety.
However, improper use can result in electric shock and/or
fire. In order to prevent potential danger, please observe
the following instructions when installing, operating and
cleaning the product. To ensure your safety and prolong
the service life of this product, please read the following
precautions carefully before use.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
E-2
2011 February 24
HT-SL50
10) Protect the power cord from being walked on or
pinched
particularly
at
plugs,
convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
1
2
3
4
5
6
7
8
9
Important Safety Instructions (continued)
Additional Safety Information
15) Power Sources - This product should be operated
only from the type of power source indicated on the
marking label. If you are not sure of the type of power
supply to your home, consult your product dealer or
local power company. For product intended to operate
from battery power, or other sources, refer to the
operating instructions.
16) Overloading - Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
17) Object and Liquid Entry - Never push objects of any
kind into this product through openings as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid
of any kind on the product.
18) Damage Requiring Service - Unplug this product from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen
into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in
any way, and
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
19) Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
20) Safety Check - Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is
in proper operating condition.
21) Wall or ceiling mounting - When mounting the product
on a wall or ceiling, be sure to install the product
according to the method recommended by the
manufacturer.
22) Power Lines - An outside antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can fall
into such power lines or circuits. When installing an
outside antenna system, extreme care should be
taken to keep from touching such power lines or
circuits as contact with them might be fatal.
23) Protective Attachment Plug - The product is equipped
with an attachment plug having overload protection.
This is a safety feature. See Instruction Manual for
replacement or resetting of protective device. If
replacement of the plug is required, be sure the
service technician has used a replacement plug
specified by the manufacturer that has the same
overload protection as the original plug.
24) Stand - Do not place the product on an unstable cart,
stand, tripod or table. Placing the product on an
unstable base can cause the product to fall, resulting
in serious personal injuries as well as damage to the
product. Use only a cart, stand, tripod, bracket or table
recommended by the manufacturer or sold with the
product. When mounting the product on a wall, be
sure to follow the manufacturer’s instructions. Use
only the mounting hardware recommended by the
manufacturer.
1
2
3
4
5
6
7
1
9
E-3
2011 February 24
HT-SL50
For U.S. customer only
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the
"Product"), when ship in its original container, will be free from defective workmanship and materials, and agrees that it will,
at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent
at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below
nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or
other misuse, abnormal service or handling, or which has been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide
proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law.
ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE
LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those
described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and
exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described
herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the
Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.
In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused
by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any
way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion
of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
Model Specific Section
Your Product Model Number & Description:
HT-SL50 Sound Bar Home Theater System
(Be sure to have this information available when you need
service for your Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
Additional Item(s) Excluded from Warranty Coverage
(if any):
Non-functional accessories, supplies, and consumable
items.
Where to Obtain Service:
At a Sharp Authorized Servicer located in the United States.
To find a location of the nearest Sharp Authorized Servicer,
call Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service:
Ship prepaid or carry in your Product to a Sharp Authorized
Servicer. Be sure to have Proof of Purchase available. If
you ship the Product, be sure it is insured and packaged
securely.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
1
2
3
4
5
6
7
8
9
E-4
2011 February 24
HT-SL50
Precautions
General
● Please ensure that the equipment is positioned in a
well-ventilated area and ensure that there is at least
4" (10 cm) of free space along the sides, top and back
of the equipment.
4" (10 cm) 4" (10 cm)
4" (10 cm)
Warning:
The voltage used must be the same as that specified on
this unit. Using this product with a higher voltage other
than that which is specified is dangerous and may result in
a fire or other type of accident causing damage. SHARP
will not be held responsible for any damage resulting from
use of this unit with a voltage other than that which is
specified.
4" (10 cm)
ACTIVE SUBWOOFER SYSTEM
HT-SL50
● Use the unit on a firm, level surface free from vibration.
● Keep the unit away from direct sunlight, strong
magnetic fields, excessive dust, humidity and
electronic/electrical equipment (home computers,
facsimiles, etc.) which generate electrical noise.
● Do not place anything on top of the system.
● Do not expose the unit to moisture, to temperatures
●
●
●
●
●
●
higher than 140°F (60°C) or to extremely low
temperatures.
If your system does not work properly, disconnect the
AC power cord from the AC outlet and replug.
In case of an electrical storm, unplug the unit for safety.
Hold the AC power plug by the head when removing it
from the AC outlet, as pulling the cord can damage
internal wires.
The AC power plug is used as a disconnect device and
shall always remain readily operable.
Do not remove the outer cover, as this may result in
electric shock. Refer internal service to your local
SHARP service facility.
This unit should only be used within the range of
41°F - 95°F (5°C - 35°C).
E-5
2011 February 24
HT-SL50
1
2
3
4
5
6
7
1
9
Controls and indicators
Sound Bar
1
2
FRONT VIEW
REAR VIEW
4
5
R
RL
R
RL
L
L
3
3
Reference page
4. Right Front Speaker terminal (Red/Black). . . . . . 9
5. Left Front Speaker terminal (White/Black) . . . . . 9
1. Left Front Speaker
2. Right Front speaker
3. Bass Reflex Duct
Subwoofer
FRONT VIEW
1
REAR VIEW
3
2
4
5
ACTIVE SUBWOOFER SYSTEM
HT-SL50
6
7
8
Reference page
Reference page
1. Stand-by Indicator
2. Bass Reflect Duct
3. Woofer
4. HDMI (TV ARC) Output Jack . . . . . . . . . . . . . . . . 10
5. HDMI Input Jack . . . . . . . . . . . . . . . . . . . . . . . . . 11
6. AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7. Speaker Terminal. . . . . . . . . . . . . . . . . . . . . . . . . . 9
8. Audio In (TV) Jack . . . . . . . . . . . . . . . . . . . . . . . . 12
E-6
2011 February 24
HT-SL50
1
2
3
4
5
6
7
8
9
System preparation
Make sure to unplug the AC power lead before
installing the unit or changing the position.
Using foot cushions
Select from three installation methods according to the
preferred position.
Option 1
Option 2
Using stand
1. Peel off the double sided tape separator and attach the
sound bar stand cushion at the bottom surface of the
sound bar stand.
Option 1
Option 2
Sound bar stand cushion
Sound bar
stand
Double
sided
tape
separator
Attach foot cushions as shown
To mount the sound bar on the wall
Caution:
● Be very careful to prevent the sound bar [1.46 lbs (0.66
kg)] from falling when mounting on the wall.
● Before mounting, check the wall strength. (Do not put
on the veneer plaster or whitewashed wall. The sound
bar may fall.) If unsure, consult a qualified service
technician.
● Mounting screws are not supplied. Use appropriate
ones.
● Check all wall mount angle screws for looseness.
● Select a good location. If not, accidents may occur or
the sound bar may get damaged.
● SHARP is not responsible for accidents resulting
from improper installation.
● Do not let children dangle on the sound bar once it is
attached on the wall as it can cause damage and injury.
Hook
2. Fix the sound bar stand as shown.
Driving screws
SHARP designed the sound bar so you may hang them on
the wall. Use proper screws (not supplied). See below for
size and type.
1/8" (3.2 mm)
Option 1
3/16"
(5 mm)
Option 2
7/8" (Min. 22 mm)
Note:
● Sound bar stand can be removed by pulling it off
backward from the sound bar.
E-7
2011 February 24
HT-SL50
3/8" (9 mm)
1
2
3
4
5
6
7
1
9
System preparation (continued)
Installing the sound bar
Fixing wall mount angle
1 Fix the pattern paper to the wall in horizontal
position as below.
1 Align the wall mount slot at the sound bar to the
wall mount angle.
523 mm
Wall surface 30 mm
30 mm
2 Slot the sound bar into the wall mount angle.
3 Fix them securely.
Wall surface
Pattern paper
2 Make a hole on the wall following the screw point
marks on the pattern paper by using a drill.
1-1/4" (32 mm)
3/8" (8-9 mm)
Wall surface
3 Fix a wall mount plug (not supplied) into the hole
using a hammer, until it is flush with the wall
surface.
1-1/4" (32 mm)
3/8" (8-9 mm)
Falling prevention
Safety wires (not supplied) are useful to prevent the sound
bar from falling off the table.
Wall surface
4 Screw the wall mount angle to the wall as shown in
the illustration. (Total screw is 4 pieces)
L
RL
R
Wall mount angle
Wall mount
angle
Wall
(screws x 2) surface
Wall
mount
angle
Wall surface
(screws x 2)
Wall surface
Note:
Make sure all screws are fully tightened. (screws are not
supplied)
E-8
2011 February 24
HT-SL50
Loop the safety wires (not supplied) into each hole as
shown and tie the safety wires to the LCD TV stand.
1
2
3
4
5
6
7
8
9
Placing the system
Installation image:
Notes:
● As the sound from the system is omni-directional, you
can place the speaker anywhere you like. However, it is
recommended to place it as close to the TV as possible.
● The front panel of the speaker is not removable.
TV
Caution:
● Do not change the installation direction when the unit is
turned on.
Placing the stand
Place the stand as shown.
ACTIVE SUBWOOFER SYSTEM
HT-SL50
Blu-ray
DVD player
Place the system as shown.
Remove the protective film covering the sound bar and
subwoofer before using the system.
SUBWOOFER SYSTEM
ACTIVE SUBWOOFER SYSTEM
HT-SL50
ACTIVE
SUBWOOFER
HT-SL50 SYSTEM
Stand
System connections
Make sure to unplug the AC power cord before making any connections.
Subwoofer
Right
Left
Sound Bar
White
AC outlet
AC 120 V ~ 60 Hz
Red
Speaker connection
Connect the wire without insulation tube to the minus (–)
terminal, and the wire with red and white insulation tube to
the plus (+) terminal.
Caution:
● Use speaker with an impedance of 4 ohms or more, as
lower impedance speaker can damage the unit.
E-9
2011 February 24
HT-SL50
● Do not make a mistake when
connecting the right and left
speakers. The right speaker is
the one on the right side when
you face the unit.
● Do not let the bare speaker
wires touch each other.
● Do not allow any objects to fall
INCORRECT
into or to be placed in the bass
reflex duct.
● Do not stand or sit on the subwoofer/sound bar. You
may be injured.
1
2
3
4
5
6
7
1
9
System connections (continued)
Connecting to TV (with HDMI)
Caution:
Turn off all other equipment before making this connection.
Notes:
● This unit supports HDMI which enables ARC (Audio Return Channel).
● To enable ARC make sure to use High Speed HDMI cable.
● This structure also needs TV that supports ARC.
● To listen to the sound from non-ARC-compatible TV, connect the audio output from TV to this system AUDIO IN (TV)
terminal.
● This unit can be operated (power on/off or volume up/down) via a TV or similar component which supports HDMI CEC
(Consumer Electronics Control). If this does not work, it does not mean this system is faulty. Refer to the operation
manual of the respective component on how to activate the CEC.
Example: Go to the Menu of the component to search and enable the CEC. Different brands may have different naming
for the CEC. For Sharp LCD TV, it is named as AQUOS LINK.
● To watch 3D images, connect 3D-compatible TV and video component (3D Blu-ray Disc player, etc.) to this system.
Make sure to use High Speed HDMI cables and put on the 3D glasses, otherwise 3D images may not be viewed
properly.
● To listen to the sound from TV, some setting in the TV menu is needed. For details refer to the operation manual of the
TV.
● If unable to select external speaker (for Sharp LCD TV, it is named as AQUOS AUDIO SP), turn OFF and ON the CEC.
● Make sure the LCD TV Audio setting is set to PCM, not other format such as Dolby Digital, DTS, etc.
Select from the 2 methods below:
1. Method 1
This connection is for HDMI TV with ARC (Audio Return Channel).
TV
To HDMI (ARC)
terminal
To HDMI output
terminal
DVD, Blu-ray
disc player or
similar
To HDMI
output
terminal
Notes:
● Refer to the operation manual of the equipment to be connected.
● Fully insert the plugs to avoid fuzzy pictures or noises.
E-10
2011 February 24
HT-SL50
1
2
3
4
5
6
7
8
9
System connections (continued)
2. Method 2
This connection is for HDMI TV without ARC (Audio Return Channel).
TV
DVD, Blu-ray disc
player or similar
To HDMI
output
terminal
To HDMI output terminal
To HDMI
terminal
To HDMI
input
terminal
1
2
3
4
5
6
7
1
9
E-11
2011 February 24
HT-SL50
System connections (continued)
Connecting a TV (with AUDIO IN (TV))
Connect to the TV using an audio cable.
1. Method 1
TV
To HEADPHONE terminal
Audio cable
Audio signal
Subwoofer
To AUDIO IN (TV)
input terminal
2. Method 2
TV
To audio output terminal
RCA cable
Audio signal
Subwoofer
To AUDIO IN (TV)
input terminal
Note:
To control the volume, some setting in the TV MENU is needed. For details refer to the operation manual of the TV.
Example: Go to the Setting Menu of the TV, select AUDIO OUT and choose VARIABLE.
However if this does not work, please use method 1.
E-12
2011 February 24
HT-SL50
1
2
3
4
5
6
7
8
9
General Control
Make sure to enable the HDMI CEC when making HDMI connection.
To turn the power on
Plug the AC power cord into an AC outlet, the stand-by
indicator turns red.
This unit will automatically power on if:
1. TV or similar component which supports HDMI CEC, is
turned on.
2. audio signal is detected from Audio input.
The stand-by indicator turns blue.
Notes:
● HDMI input will override the Audio input signal.
● Audio input will function only when there is no signal
from HDMI input.
Audio Return Channel (ARC) (Audio
Return Channel submenu)
The audio return channel (ARC) enables an HDMI ARCcapable TV to send the audio stream to the HDMI OUT
jack of the receiver. To use this function, your TV must
support the ARC.
Volume
Volume can only be controlled from your TV.
Power Off
This unit will automatically go to stand-by mode if:
1. TV or similar component which supports HDMI CEC, is
turned off.
2. no signal from Audio input is detected after 1 minute.
1
2
3
4
5
6
7
1
9
E-13
2011 February 24
HT-SL50
Troubleshooting chart
Many potential problems can be resolved by the owner
without calling a service technician.
If something is wrong with this product, check the following
before calling your authorized SHARP dealer or service
center.
General
Symptom
● No sound is heard.
Possible cause
Condensation
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation
inside the cabinet. Condensation can cause the unit to
malfunction. If this happens, leave the power on until
normal playback is possible (about 1 hour). Wipe off any
condensation on the transmitter with a soft cloth before
operating the unit.
● Is the input signal
If problem occurs during operation
(selection) set properly?
● Is HDMI compliant
equipment being used?
● Is the HDMI cable
connected correctly?
Connect the HDMI cable
correctly.
● Is the sound input support
PCM signal?
● Do not connect or
disconnect an HDMI cable
while power is on. This
may lead to operation
problems.
● Noise is heard
during playback.
● The power is not
turned on.
● Move the speaker away
controlled.
Maintenance
Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth.
Caution:
● Do not use chemicals for cleaning (gasoline, paint
thinner, etc.). It may damage the cabinet finish.
● Do not apply oil to the inside of each component. It may
cause malfunctions.
from any computers or
mobile phones.
● Is the unit unplugged?
● The protection circuit may
be activated. Unplug and
plug in the power cord
again after 5 minutes or
more.
● Volume cannot be
When this product is subject to strong external interference
(mechanical shock, excessive static electricity, abnormal
supply voltage due to lightning, etc.) or if it is operated
incorrectly, it may malfunction.
If the unit is not restored in the previous operation,
unplug and plug in the unit again
or
unplug all components connected and plug in again.
● Check if the HDMI CEC is
enabled.
● For headphone or RCA,
TV setting (VARIABLE) is
required.
● 3D images not
displayed on the TV.
● Depending on the TV and
Video component, 3D
images may not be
displayed.
Check the operation
manual of the respective
component.
1
2
3
4
5
6
7
8
9
E-14
2011 February 24
HT-SL50
Specifications
As part of our policy of continuous improvement, SHARP
reserves the right to make design and specification
changes for product improvement without prior notice. The
performance specification figures indicated are nominal
values of production unit. There maybe some deviations
from these values in individual unit.
General
Power source AC 120 V ~ 60 Hz
Power
25 W
consumption
Output power RMS: Total 100 watts
RMS:
Front Left/Right:
25 watts per channel into 4 ohms at
1 kHz, 10% total harmonic distortion
Subwoofer:
50 watts per channel into 8 ohms at
100 Hz, 10% total harmonic distortion
FTC:
Front:(Left/Right):
Minimum 24 watts per channel into
4 ohms at 200 Hz to 20 kHz, 1% total
harmonic distortion
Subwoofer:
Minimum 50 watts per channel into
8 ohms at 100 Hz, 1% total harmonic
distortion
Output
HDMI™ output: (audio/video support to
terminal
1080p) x 1
Input
Analog input (Audio in):
terminal
Stereo mini jack Ø 3.5 mm
HDMI input: (audio/ video support to
1080p) x 1
Soundbar speaker
Type
Maximum
input power
Rated input
power
Impedance
Dimensions
Weight
Full Range speaker system
7/8" x 4-1/2" (2.2 x 11.5 cm)
Full Range
50 W/CH
25 W/CH
4 ohms/CH (3 pieces parallel)
Width: 31-1/2" (801 mm)
Height: 1-1/16" (26 mm)
Depth: 2" (50 mm)
1.46 lbs. (0.66 kg)
Subwoofer
Type
Maximum
input power
Rated input
power
Impedance
Dimensions
Weight
Subwoofer system
6 - 5/16" (16 cm) woofer
100 W
50 W
8 ohms
Width: 4 - 1/2" (115 mm)
Height: 16 - 5/8" (422 mm)
Depth: 12 - 1/16" (307 mm)
9.92 lbs. (4.50 kg)
1
2
3
4
5
6
7
1
9
E-15
2011 February 24
HT-SL50