DISPLAY ENGLISH SCIENTIFIC CALCULATOR Symbol EL-W531 EL-W531G EL-W531H EL-W531HA EL-W535 Dot matrix display Mantissa Exponent Thank you for purchasing the SHARP Scientific Calculator Model EL-W531/W531G/W531H/W531HA/W535. About the calculation examples (including some formulas and tables), refer to the reverse side of this English manual. Refer to the number on the right of each title in the manual for use. After reading this manual, store it in a convenient location for future reference. Notes: • Some of the models described in this manual may not be available in some countries. • This product uses a period as a decimal point. • During actual use, not all symbols are displayed at the same time. • Only the symbols required for the usage under instruction are shown in the display and calculation examples of this manual. Indicates that some contents are hidden in the / : / directions shown. 2ndF: Appears when @ is pressed, indicating that the functions shown in orange are enabled. HYP: Indicates that H has been pressed and the hyperbolic functions are enabled. If @ > is pressed, the symbols “2ndF HYP” appear, indicating that inverse hyperbolic functions are enabled. ALPHA: Indicates that ;, x or t has been pressed, and entry (recall) of memory contents and recall of statistics can be performed. DEG/RAD/GRAD: Indicates angular units. BUSY: Appears during the execution of a calculation. W-VIEW: Indicates that the WriteView editor is selected. M: Indicates that a numerical value is stored in the independent memory (M). ENG/SCI/FIX/N2/N1: Indicates the notation used to display a value and changes by SET UP menu. N1 is displayed on-screen as “NORM1”, and N2 as “NORM2”. Operational Notes BEFORE USING THE CALCULATOR MODEL OPERATION MANUAL PRINTED IN CHINA / IMPRIMÉ EN CHINE / IMPRESO EN CHINA 07BGK (TINSE1278EHZZ) INTRODUCTION • Do not carry the calculator around in your back pocket, as it may break when you sit down. The display is made of glass and is particularly fragile. • Keep the calculator away from extreme heat such as on a car dashboard or near a heater, and avoid exposing it to excessively humid or dusty environments. • Since this product is not waterproof, do not use it or store it where fluids, for example water, can splash onto it. Raindrops, water spray, juice, coffee, steam, perspiration, etc. will also cause malfunction. • Clean with a soft, dry cloth. Do not use solvents or a wet cloth. • Do not drop it or apply excessive force. • Never dispose of batteries in a fire. • Keep batteries out of the reach of children. • This product, including accessories, may change due to upgrading without prior notice. When using for the first time, press the RESET switch (on the back), with the tip of a ball-point pen or similar object. Adjusting the Display Contrast Press J 3, then + or & to adjust the contrast. Press j to exit. Power On and Off Press j to turn the calculator on. The data that was onscreen when the power was turned off will appear on the display. Press @ o to turn it off. Key Notations Used in this Manual In this manual, key operations are described as follows: To specify e x: @ " To specify ln: i To specify E: ; E NOTICE • SHARP strongly recommends that separate permanent written records be kept of all important data. Data may be lost or altered in virtually any electronic memory product under certain circumstances. Therefore, SHARP assumes no responsibility for data lost or otherwise rendered unusable whether as a result of improper use, repairs, defects, battery replacement, use after the specified battery life has expired, or any other cause. • SHARP will not be liable nor responsible for any incidental or consequential economic or property damage caused by misuse and/or malfunctions of this product and its peripherals, unless such liability is acknowledged by law. ♦ Press the RESET switch (on the back), with the tip of a ball-point pen or similar object, only in the following cases. Do not use an object with a breakable or sharp tip. Note that pressing the RESET switch erases all data stored in memory. • When using for the first time • After replacing the battery • To clear all memory contents • When an abnormal condition occurs and all keys are inoperative If service should be required on this calculator, use only a SHARP servicing dealer, SHARP approved service facility, or SHARP repair service where available. Hard Case Remove the hard case, holding it with your fingers in the positions shown below. • Functions that are printed in orange above the key require @ to be pressed first before the key. When you specify the memory, press ; first. Numbers for input values are not shown as keys, but as ordinary numbers. • Functions that are printed in gray adjacent to the keys are effective in specific modes. The WriteView and Line Editors This calculator has the following two editors in NORMAL mode: WriteView and Line. You can select between them in the SET UP menu. The Line editor Note: In certain calculation examples, where you see the o symbol, the key operations and calculation results are shown as they would appear in the Line editor. Clearing the Entry and Memories Entry A–F*1, D1–D4*2 ANS STAT*3 (Display) M, X, Y j ○ × × × × ○ × × ○ ○ @Z Mode selection (b) ○ × × × ×*5 ○ × × × × @ P 0*4 ○ ○ ○ ○ ○ @ P 1 0*4 ○ ○ ○ ○ ○ @ P 2 0*4 RESET switch ○ ○ ○ ○ ○ ○: Clear ×: Retain Operation Binary, Pental, Octal, Decimal, and Hexadecimal 11 Operations (N-base) –x Conversions can be performed between N-base numbers in NORMAL mode. The four basic arithmetic operations, calculations with parentheses, and memory calculations can also be performed, along with the logical operations AND, OR, NOT, NEG, XOR, and XNOR on binary, pental, octal, and hexadecimal numbers. Conversion to each system is performed with the following keys: @ z (“BIN” appears), @ r (“PEN” appears), @ g (“OCT” appears), @ h (“HEX” appears), @ / (“BIN”, “PEN”, “OCT”, and “HEX” disappear) Note: The hexadecimal numbers A–F are entered by pressing sx Sample standard deviation (x data) σx Population standard deviation (x data) n Number of samples A B C D E 13 • Before performing a calculation, select the angular unit. • The calculation result is automatically stored in the X and Y memories (r or x in X memory, and θ or y in Y memory). • The results of coordinate conversions will be displayed as decimal numbers even in the WriteView editor. Rectangular coord. Polar coord. Modify Function 14 Decimal calculation results are internally obtained in scientific notation, with up to 14 digits in the mantissa. However, since calculation results are displayed in the form designated by the display notation and the number of decimal places indicated, the internal calculation result may differ from that shown in the display. By using the modify function (@ n), the internal value is converted to match that of the display, so that the displayed value can be used without change in subsequent operations. • When using the WriteView editor, if the calculation result is displayed using fractions or irrational numbers, press U to convert it to decimal form first. STATISTICAL CALCULATIONS Displaying calculation results When possible, calculation results will be displayed using fractions, r, and π. When you press U, the display will cycle through the following display styles: improper fractions (with • Mixed fractions (with or without π) decimal numbers or without π) decimal numbers • Proper fractions (with or without π) • Irrational numbers (square roots, fractions made using square roots) decimal numbers Notes: • In the following cases, calculation results may be displayed using r: • Arithmetic operations and memory calculations • Trigonometric calculations • In trigonometric calculations, when Entry value entering values such as those in multiples of 15 the table to the right, results may be DEG 1 shown using r. RAD multiples of ⎯ 12 π • Calculation results may extend off 50 GRAD multiples of ⎯ 3 the edges of the screen. You can see those parts by pressing l or r (depending on whether the left or right portion is hidden). • Improper/proper fractions will be converted to and displayed as decimal numbers if the number of digits used in their expression is greater than nine. In the case of mixed fractions, the maximum number of displayable digits (including integers) is eight. • If the number of digits in the denominator of a fractional result that uses π is greater than three, the result is converted to and displayed as a decimal number. The Line Editor Entry and display In the Line editor, you can enter and display equations line by line. Notes: • Up to three lines of text may be viewed on the screen at one time. • If the length of the equation exceeds three lines, parts of it may be hidden from view after calculation. If you want to see the rest of the equation, press l or r to return to the editing screen. • In the Line editor, calculation results are displayed in decimal form. Back space and delete key To delete a number or function, move the cursor to the right of it, then press N. You can also delete a number or function that the cursor is directly over by pressing @ y. Multi-line Playback Function 2 This calculator is equipped with a function to recall previous equations and answers in NORMAL mode. A maximum of 340 characters can be stored in memory. When the memory is full, stored equations will be deleted to make room, starting with the oldest. Pressing u will display the previous equation. Further pressing u will display preceding equations (after returning to the previous equation, press d to view equations in order). In addition, @ u can be used to jump to the oldest equation, and @ d to jump to the newest one. • To edit an equation after recalling it, press l or r. • The multi-line memory will be cleared by the following operations: @ Z , mode change, RESET, N-base conversion, angular unit conversion, editor change (J 2 0 or J 2 1), and memory clear (@ P 1 0). Sum of squares of samples (x data) Mean of samples ( y data) To exit DRILL mode, press b and select another mode. sy Sample standard deviation ( y data) Using Math Drill and × Table σy Population standard deviation ( y data) Sum of samples (x data) 2 Σy Σy Sum of samples ( y data) 2 Sum of squares of samples ( y data) Σ xy Sum of products of samples (x, y) r Correlation coefficient a Coefficient of regression equation b Coefficient of regression equation c Coefficient of quadratic regression equation • Use ; and t to perform a variable calculation in STAT mode. • U does not function in STAT mode. 16 Data entry Single-variable data Data _ Data H frequency _ (To enter multiples of the same data) Two-variable data Data x H data y _ Data x H data y H frequency _ (To enter multiples of the same data x and y) Note: Up to 100 data items can be entered. With the singlevariable data, a data item without frequency assignment is counted as one data item, while an item assigned with frequency is stored as a set of two data items. With the two-variable data, a set of data items without frequency assignment is counted as two data items, while a set of items assigned with frequency is stored as a set of three data items. 1. Press b 2 0 for Math Drill or b 2 1 for × Table. 2. Math Drill: Use u and d to select the number of questions (25, 50, or 100). × Table: Use u and d to select a row in the multiplication table (1 to 12). 3. Math Drill: Use l and r to select the operator type for questions (+, −, ×, ÷, or +−×÷). × Table: Use l and r to select the order type (“Serial” or “Random”). 4. Press e to start. When using Math Drill or × Table (random order only), questions are randomly selected and will not repeat except by chance. 5. Enter your answer. Press j or N to clear the entered number and then enter the correct answer. 6. Press e. • If the answer is correct, “ ” appears and the next question is displayed. • If the answer is wrong, “ ”appears and the same question is displayed. This will be regarded as an incorrect answer. • If you press e without entering an answer, the correct answer is displayed and then the next question is displayed. This will be regarded as an incorrect answer. 7. Continue answering the series of questions by entering the answer and pressing e. 8. After you finish, press e and the number and percentage of correct answers are displayed. 9. Press e to return to the initial screen for your current drill. Math Drill sample Current question/ Total questions Question ⋮ Data correction Correction before pressing _ immediately after a data entry: Delete incorrect data with j, then enter the correct data. Correction after pressing _: Use u and d to display the previously entered data set. Press d to display the data set in ascending (oldest first) order. To reverse the display order to descending (latest first), press the u key. Press @ u or @ d to jump the cursor to the beginning or end of the data set. Each data set is displayed with “X:”, “Y:”, or “F:”. See step 6 above. ⋮ Number of questions Operator type Percentage correct Correct answers Data set number Data x Frequency Total remaining questions Question Data set number Data x Data y Frequency 15 The following statistics can be obtained for each statistical calculation (refer to the table below): Single-variable statistical calculation Statistics of ①. Linear regression calculation Statistics of ① and ②. In addition, the estimate of y for a given x (estimate y´) and the estimate of x for a given y (estimate x´). Quadratic regression calculation Statistics of ① and ②, and coefficients a, b, c in the quadratic regression formula ( y = a + bx + cx 2). (For quadratic regression calculations, no correlation coefficient (r) can be obtained.) When there are two x´ values, each value will be displayed with “1:” or “2:”, and stored separately in the X and Y memories. Euler exponential regression, logarithmic regression, power regression, inverse regression, and general exponential regression calculations Statistics of ① and ②. In addition, the estimate of y for a given x and the estimate of x for a given y. (Since the calculator converts each formula into a linear regression formula before actual calculation takes place, it obtains all statistics, except coefficients a and b, from converted data rather than entered data.) ⋮ See step 6 above. Display and move the cursor to the data item to be modified by using u and d, input the correct value, then press _ or e. • To delete a data set, display and move the cursor to an item of the data set to delete by using u and d, then press @ #. The data set will be deleted. • To add a new data set, press j to exit the display of previously entered data and input the values, then press _. Statistical Calculation Formulas Type Regression formula Linear y = a + bx Quadratic y = a + bx + cx 2 Euler exponential y = a ⋅ ebx Logarithmic y = a + b ⋅ ln x Power y = a ⋅ xb Inverse 1 y=a+b⎯ x General exponential y = a ⋅ bx An error will occur when: • The absolute value of the intermediate result or calculation result is equal to or greater than 1 × 10100. • The denominator is zero. • An attempt is made to take the square root of a negative number. • No solution exists in the quadratic regression calculation. Priority Levels in Calculation This calculator performs operations according to the following priority: ① Fractions (1m4, etc.) ② Functions preceded by their argument (x −1, x 2, n!, etc.) ③ y x, xr ④ Implied multiplication of a memory value (2Y, etc.) ⑤ Functions followed by their argument (sin, cos, 1 etc.) ⑥ Implied multiplication of a function (2sin 30, A ⎯ 4 , etc.) ⑦ nCr, nPr ⑧ ×, ÷ ⑨ +, − ⑩ AND ⑪ OR, XOR, XNOR ⑫ =, M+, M−, ⇒M, ▶DEG, ▶RAD, ▶GRAD, DATA, CD, r θ, xy, and other calculation ending instructions • If parentheses are used, parenthesized calculations have precedence over any other calculations. INITIAL SET UP Mode Selection NORMAL mode: b 0 (default) Used to perform arithmetic operations and function calculations. Multiplicand Order type Percentage correct Correct answers Ranges of Math Drill Questions The range of questions for each operator type is as follows. + Addition operator: “0 + 0” to “20 + 20” ] Subtraction operator: “0 − 0” to “20 − 20”; answers are positive integers and 0. > Multiplication operator: “1 × 0” or “0 × 1” to “12 × 12” ) Division operator: “0 ÷ 1” to “144 ÷ 12”; answers are positive integers from 1 to 12 and 0, dividends of up to 144, and divisors of up to 12. +]>) Mixed operators: Questions within all the above ranges are displayed. ERRORS AND CALCULATION RANGES Errors An error will occur if an operation exceeds the calculation ranges, or if a mathematically illegal operation is attempted. When an error occurs, pressing l or r automatically moves the cursor back to the place in the equation where the error occurred. Edit the equation or press j to clear the equation. Functions 6 • Refer to the calculation examples for each function. • In the Line editor, the following symbols are used: : to indicate an expression’s power. (m, @ ", • @ Y) • : to separate integers, numerators, and denominators. (W, @ k) • When using @ O or @ W in the Line editor, values are entered in the following way: • logn (base, value) • abs value Random Function The random function has four settings. (This function cannot be selected while using the N-base function.) To generate further random numbers in succession, press e. Press j to exit. Random numbers A pseudo-random number, with three significant digits from 0 up to 0.999, can be generated by pressing @ w 0 e. Note: In the WriteView editor, the result will be a fraction or 0. Random dice To simulate a die-rolling, a random integer between 1 and 6 can be generated by pressing @ w 1 e. Random coin To simulate a coin flip, 0 (heads) or 1 (tails) can be randomly generated by pressing @ w 2 e. STAT mode: b 1 Used to perform statistical operations. DRILL mode: b 2 Used to practice math and multiplication table drills. Random integer An integer between 0 and 99 can be generated randomly by pressing @ w 3 e. SET UP Menu Press J to display the SET UP menu. Press j to exit the SET UP menu. Angular Unit Conversions Determination of the angular unit The following three angular units (degrees, radians, and grads) can be specified. DEG (°): J 0 0 (default) RAD (rad): J 0 1 GRAD (g): J 0 2 Memory Calculations 3 Selecting the display notation and decimal places Five display notation systems are used to display calculation results: Two settings of Floating point (NORM1 and NORM2), Fixed decimal point (FIX), Scientific notation (SCI), and Engineering notation (ENG). • When J 1 0 (FIX) or J 1 2 (ENG) is pressed, “TAB(0–9)?” will be displayed and the number of decimal places (TAB) can be set to any value between 0 and 9. • When J 1 1 (SCI) is pressed, “SIG(0–9)?” will be displayed and the number of significant digits can be set to any value between 0 and 9. Entering 0 will set a 10-digit display. Setting the floating point number system in scientific notation Two settings are used to display a floating-point number: NORM1 (the default) and NORM2. A number is automatically displayed in scientific notation outside a preset range: • NORM1 (J 1 3): 0.000000001 ≤ | x | ≤ 9,999,999,999 • NORM2 (J 1 4): 0.01 ≤ | x | ≤ 9,999,999,999 Selecting the editor Two editors are available in NORMAL mode: • The WriteView editor (W-VIEW): J 2 0 (default) • The Line editor (LINE): J 2 1 Adjusting the display contrast Press J 3, then + or & to adjust the contrast. Press j to exit. Insert and overwrite entry methods When using the Line editor, you can change the entry method from “INSERT” (the default) to “OVERWRITE”. After you switch to the overwrite method (by pressing J 4 1), the triangular cursor will change to a rectangular one, and the number or function underneath it will be overwritten as you make entries. SCIENTIFIC CALCULATIONS • Press b 0 to select NORMAL mode. • In each example, press j to clear the display first. Unless otherwise specified, calculation examples are performed in the WriteView editor with the default display settings (@ P 0). Arithmetic Operations 4 • The closing parenthesis ) just before = or m may be omitted. Constant Calculations 5 • In constant calculations, the addend becomes a constant. Subtraction and division are performed in the same manner. For multiplication, the multiplicand becomes a constant. • In constant calculations, constants will be displayed as K. ERROR 02: Calculation error • The absolute value of an intermediate or final calculation result equals or exceeds 10100. • An attempt was made to divide by zero (or an intermediate calculation resulted in zero). • The calculation ranges were exceeded while performing calculations. Independent memory (M) In addition to all the features of temporary memories, a value can be added to or subtracted from an existing memory value. Press j x M to clear the independent memory (M). Last answer memory (ANS) The calculation result obtained by pressing = or any other calculation ending instruction is automatically stored in the last answer memory. Notes: • Calculation results from the functions indicated below are automatically stored in the X or Y memories replacing any existing values. r θ, xy: X memory (r or x), Y memory (θ or y) • • Two x´ values from a quadratic regression calculation in STAT mode: X memory (1:), Y memory (2:) • Use of t or ; will recall the value stored in memory using up to 14 digits. Definable memories (D1–D4) You can store functions or operations in definable memories (D1–D4). • To store a function or operation, press x, followed by a definable memory key (I, J, K, or L), followed by the operation you want to store. Menu-related operations, such as J, cannot be stored. Press j to return to the previous display. • To call a stored function or operation, press the corresponding memory key. Calling a stored function will do nothing if the function that is called would be unusable in the current context. • Any functions or operations that are stored in a definable memory will be replaced when you save a new one into that memory. • When displaying and correcting a data set in STAT mode, you cannot store functions or operations in definable memories. Chain Calculations 9 The previous calculation result can be used in the subsequent calculation. However, it cannot be recalled after entering multiple instructions. Fraction Calculations 10 Arithmetic operations and memory calculations can be performed using fractions. In NORMAL mode, conversion between a decimal number and a fraction can be performed by pressing U. Notes: • Improper/proper fractions will be converted to and displayed as decimal numbers if the number of digits used in their expression is greater than nine. In the case of mixed fractions, the maximum number of displayable digits (including integers) is eight. • To convert a sexagesimal value to a fraction, first convert it by pressing @ :. Replacement Procedure ERROR 03: Nesting error • The available number of buffers was exceeded. (There are 10 buffers for numeric values and 64 buffers for calculation instructions). ERROR 04: Data over • Data items exceeded 100 in STAT mode. 18 Cannot delete! • The selected item cannot be deleted by pressing N or @ y in the WriteView editor. Ex. * 5 r A l N In this example, delete the exponent before attempting to delete the parentheses. Cannot call! • The function or operation stored in definable memory (D1 to D4) cannot be called. Ex. An attempt was made to recall a statistical variable from within NORMAL mode. Buffer full! • The equation (including any calculation ending instructions) exceeded its maximum input buffer (159 characters in the WriteView editor or 161 characters in the Line editor). An equation may not exceed its maximum input buffer. Calculation Ranges 8 Memory calculations can be performed in NORMAL and STAT modes. Temporary memories (A–F, X and Y) Press x and a variable key to store a value in memory. Press t and a variable key to recall the value from that memory. To place a variable in an equation, press ; and a variable key. • If the product is not to be used for some time, to avoid damage to the unit from a leaking battery, remove it and store in a safe place. • Do not leave an exhausted battery inside the product. • Keep batteries out of the reach of children. • An exhausted battery left in the calculator may leak and damage the calculator. • Explosion risk may be caused by incorrect handling. • Do not throw batteries into a fire as they may explode. ERROR 01: Syntax error • An attempt was made to perform an invalid operation. Ex. 2 + & 5 = Alert Messages 7 Each time @ ] is pressed, the angular unit changes in sequence. 1. Turn the power off by pressing @ o. 2. Remove the two screws. (Fig. 1) 3. Slide the battery cover slightly and lift it to remove. 4. EL-W531/W531G/W535: Remove the used battery by prying it out with a ball-point pen or other similar pointed device. (Fig. 2) EL-W531H/W531HA: Remove the used battery. 5. EL-W531/W531G/W535: Install one new battery. Make sure the “+” side is facing up. EL-W531H/W531HA: Install one new battery. First insert the “−” side toward the spring. (Fig. 3) 6. Replace the cover and screws. 7. Press the RESET switch (on the back) with the tip of a ball-point pen or similar object. 8. Adjust the display contrast. See “Adjusting the Display Contrast”. • Make sure that the display appears as shown below. If the display does not appear as shown, remove the battery, reinstall it, and check the display once again. Fig. 1 Fig. 2 Fig. 3 19 • Within the ranges specified, this calculator is accurate to ±1 of the 10th digit of the mantissa. However, a calculation error increases in continuous calculations due to accumulation of each calculation error. (This is the same for y x, xr, n!, e x, ln, etc., where continuous calculations are performed internally.) Additionally, a calculation error will accumulate and become larger in the vicinity of inflection points and singular points of functions. • Calculation ranges ±10−99 to ±9.999999999 × 1099 and 0. If the absolute value of an entry or a final or intermediate result of a calculation is less than 10−99, the value is considered to be 0 in calculations and in the display. Automatic Power Off Function Display of results using r Calculation results may be displayed using r when all of the following conditions are met: • When intermediate and final calculation results are displayed in the following form: P b cP d ±a⎯ e ± ⎯ f • When each coefficient falls into the following ranges: 1 ≤ a < 100; 1 < b < 1,000; 0 ≤ c < 100; 1 ≤ d < 1,000; 1 ≤ e < 100; 1 ≤ f < 100 • When the number of terms in the intermediate and final calculation results is one or two. Note: The result of two fractional terms that include r will be reduced to a common denominator. Internal calculations: Mantissas of up to 14 digits Pending operations: 64 calculations 10 numeric values Power source: EL-W531/W535 1.5 V — … (DC): Alkaline battery (LR44 or equivalent) × 1 EL-W531G Built-in solar cells 1.5 V — … (DC): Backup battery (Alkaline battery (LR44 or equivalent) × 1) EL-W531H/W531HA 1.5 V — … (DC): Heavy duty manganese battery (size AAA or R03) × 1 Power consumption: EL-W531/W531H/W531HA/W535 0.00011 W Operating time: EL-W531/W535 (varies according to Approx. 3,000 hours when continuously use and other factors) displaying 55555. at 25°C (77°F) EL-W531G Approx. 3,000 hours when continuously displaying 55555. at 25°C (77°F), using the alkaline battery only EL-W531H/W531HA Approx. 17,000 hours when continuously displaying 55555. at 25°C (77°F) Operating temperature: 0°C–40°C (32°F–104°F) External dimensions: 79.6 mm (W) × 161.5 mm (D) × 15.5 mm (H) 3-1/8” (W) × 6-11/32” (D) × 5/8” (H) Weight: EL-W531/W535 Approx. 100 g (0.22 lb) (including battery) EL-W531G Approx. 102 g (0.23 lb) (including battery) EL-W531H/W531HA Approx. 107 g (0.24 lb) (including battery) Accessories: Battery × 1 (installed), operation manual, and hard case BATTERY REPLACEMENT Notes on Battery Replacement ⋮ 17 • Equations that have one result require an additional eleven characters’ worth of memory to store in order to hold the result. • In addition to the amount of memory needed to store an equation, the WriteView editor will require a certain amount for the sake of display. • Equations also include calculation ending instructions, such as “=”. Error codes and error types – y Σx ② Just after obtaining an answer, pressing l brings you to the end of the equation and pressing r brings you to the beginning. Press l, r, u, or d to move the cursor. Press @ l or @ r to jump the cursor to the beginning or the end of the equation. In the WriteView editor, you can use u and d to move the cursor up and down—between the numerator and denominator, for example. × Table sample Statistical calculations can be performed in STAT mode. There are eight sub-modes within STAT mode. Press b 1, then press the number key that corresponds to your choice: 0 (S#a# 0 [SD]): Single-variable statistics 1 (S#a# 1 [LINE]): Linear regression 2 (S#a# 2 [QUAD]): Quadratic regression 3 (S#a# 3 [E_EXP]): Euler exponential regression 4 (S#a# 4 [LOG]): Logarithmic regression 5 (S#a# 5 [POWER]): Power regression 6 (S#a# 6 [INV]): Inverse regression 7 (S#a# 7 [G_EXP]): General exponential regression Statistical Calculations and Variables Entry and display In the WriteView editor, you can enter and display fractions or certain functions as you would write them. Notes: • The WriteView editor can only be used in NORMAL mode. • If the equation grows too large, it may extend off the edge of the display after you obtain the result. If you want to see the entire equation, press l or r to return to the editing screen. Math Drill: b 2 0 Math operation questions with positive integers and 0 are displayed randomly. It is possible to select the number of questions and operator type. Before entering new data, clear the memory contents. Coordinate Conversions The WriteView Editor Multiplication Table (× Table): b 2 1 Questions from each row of the multiplication table (1 to 12) are displayed serially or randomly. Data Entry and Correction Second Minute 1 DRILL MODE Mean of samples (x data) Σx 12 Conversion between decimal and sexagesimal numbers can be performed. In addition, the four basic arithmetic operations and memory calculations can be performed using the sexagesimal system. Notation for sexagesimal is as follows: Degree ① F Time, Decimal, and Sexagesimal Calculations ENTERING, DISPLAYING, AND EDITING THE EQUATION Editing the Equation The WriteView editor (default) *1 Press j x and then choose a memory to clear one variable memory. *2 Definable memory. See “Memory Calculations”. *3 Statistical data (entered data) *4 See “Memory clear key”. *5 Cleared when changing between sub-modes in STAT mode. m , * , A , l , i , and H. In the binary, pental, octal, and hexadecimal systems, fractional parts cannot be entered. When a decimal number having a fractional part is converted into a binary, pental, octal, or hexadecimal number, the fractional part will be truncated. Likewise, when the result of a binary, pental, octal, or hexadecimal calculation includes a fractional part, the fractional part will be truncated. In the binary, pental, octal, and hexadecimal systems, negative numbers are displayed as a complement. Memory clear key Press @ P to display the menu. • To initialize the display settings, press 0. The parameters set as follows: • Angular unit: DEG • Display notation: NORM1 • N-base: DEC • To clear all variables and memories (A−F, M, X, Y, D1−D4, ANS, and STAT) at once, press 1 0. • To RESET the calculator, press 2 0. The RESET operation will erase all data stored in memory and restore the calculator’s default settings. Improper handling of batteries can cause electrolyte leakage or explosion. Be sure to observe the following handling rules: • Make sure the new battery is the correct type. • When installing, orient the battery properly as indicated in the calculator. • The battery is factory-installed before shipment, and may be exhausted before it reaches the service life stated in the specifications. Notes on erasure of memory contents When the battery is replaced, the memory contents are erased. Erasure can also occur if the calculator is defective or when it is repaired. Make a note of all important memory contents in case accidental erasure occurs. When to Replace the Battery EL-W531/W531H/W531HA/W535: If the display has poor contrast even after adjusting the display contrast, the battery requires replacement. EL-W531G: If the display has poor contrast or nothing appears on the display when j is pressed in dim lighting, even after adjusting the display contrast, it is time to replace the battery. Cautions • Fluid from a leaking battery accidentally entering an eye could result in serious injury. Should this occur, wash with clean water and immediately consult a doctor. • Should fluid from a leaking battery come in contact with your skin or clothes, immediately wash with clean water. This calculator will turn itself off to save battery power if no key is pressed for approximately 10 minutes. SPECIFICATIONS Calculation features: Scientific calculations, statistical calculations, etc. Drill features: Math Drill and Multiplication Table Display: 96 × 32 dot matrix liquid crystal display Display of calculation results: Mantissa: 10 digits Exponent: 2 digits FOR MORE INFORMATION ABOUT SCIENTIFIC CALCULATORS Visit our Web site. http://sharp-world.com/calculator/ DISPLAY ENGLISH SCIENTIFIC CALCULATOR Symbol EL-W531 EL-W531G EL-W531H EL-W531HA EL-W535 Dot matrix display Mantissa Exponent Thank you for purchasing the SHARP Scientific Calculator Model EL-W531/W531G/W531H/W531HA/W535. About the calculation examples (including some formulas and tables), refer to the reverse side of this English manual. Refer to the number on the right of each title in the manual for use. After reading this manual, store it in a convenient location for future reference. Notes: • Some of the models described in this manual may not be available in some countries. • This product uses a period as a decimal point. • During actual use, not all symbols are displayed at the same time. • Only the symbols required for the usage under instruction are shown in the display and calculation examples of this manual. Indicates that some contents are hidden in the / : / directions shown. 2ndF: Appears when @ is pressed, indicating that the functions shown in orange are enabled. HYP: Indicates that H has been pressed and the hyperbolic functions are enabled. If @ > is pressed, the symbols “2ndF HYP” appear, indicating that inverse hyperbolic functions are enabled. ALPHA: Indicates that ;, x or t has been pressed, and entry (recall) of memory contents and recall of statistics can be performed. DEG/RAD/GRAD: Indicates angular units. BUSY: Appears during the execution of a calculation. W-VIEW: Indicates that the WriteView editor is selected. M: Indicates that a numerical value is stored in the independent memory (M). ENG/SCI/FIX/N2/N1: Indicates the notation used to display a value and changes by SET UP menu. N1 is displayed on-screen as “NORM1”, and N2 as “NORM2”. Operational Notes BEFORE USING THE CALCULATOR MODEL OPERATION MANUAL PRINTED IN CHINA / IMPRIMÉ EN CHINE / IMPRESO EN CHINA 07BGK (TINSE1278EHZZ) INTRODUCTION • Do not carry the calculator around in your back pocket, as it may break when you sit down. The display is made of glass and is particularly fragile. • Keep the calculator away from extreme heat such as on a car dashboard or near a heater, and avoid exposing it to excessively humid or dusty environments. • Since this product is not waterproof, do not use it or store it where fluids, for example water, can splash onto it. Raindrops, water spray, juice, coffee, steam, perspiration, etc. will also cause malfunction. • Clean with a soft, dry cloth. Do not use solvents or a wet cloth. • Do not drop it or apply excessive force. • Never dispose of batteries in a fire. • Keep batteries out of the reach of children. • This product, including accessories, may change due to upgrading without prior notice. When using for the first time, press the RESET switch (on the back), with the tip of a ball-point pen or similar object. Adjusting the Display Contrast Press J 3, then + or & to adjust the contrast. Press j to exit. Power On and Off Press j to turn the calculator on. The data that was onscreen when the power was turned off will appear on the display. Press @ o to turn it off. Key Notations Used in this Manual In this manual, key operations are described as follows: To specify e x: @ " To specify ln: i To specify E: ; E NOTICE • SHARP strongly recommends that separate permanent written records be kept of all important data. Data may be lost or altered in virtually any electronic memory product under certain circumstances. Therefore, SHARP assumes no responsibility for data lost or otherwise rendered unusable whether as a result of improper use, repairs, defects, battery replacement, use after the specified battery life has expired, or any other cause. • SHARP will not be liable nor responsible for any incidental or consequential economic or property damage caused by misuse and/or malfunctions of this product and its peripherals, unless such liability is acknowledged by law. ♦ Press the RESET switch (on the back), with the tip of a ball-point pen or similar object, only in the following cases. Do not use an object with a breakable or sharp tip. Note that pressing the RESET switch erases all data stored in memory. • When using for the first time • After replacing the battery • To clear all memory contents • When an abnormal condition occurs and all keys are inoperative If service should be required on this calculator, use only a SHARP servicing dealer, SHARP approved service facility, or SHARP repair service where available. Hard Case Remove the hard case, holding it with your fingers in the positions shown below. • Functions that are printed in orange above the key require @ to be pressed first before the key. When you specify the memory, press ; first. Numbers for input values are not shown as keys, but as ordinary numbers. • Functions that are printed in gray adjacent to the keys are effective in specific modes. The WriteView and Line Editors This calculator has the following two editors in NORMAL mode: WriteView and Line. You can select between them in the SET UP menu. The Line editor Note: In certain calculation examples, where you see the o symbol, the key operations and calculation results are shown as they would appear in the Line editor. Clearing the Entry and Memories Entry A–F*1, D1–D4*2 ANS STAT*3 (Display) M, X, Y j ○ × × × × ○ × × ○ ○ @Z Mode selection (b) ○ × × × ×*5 ○ × × × × @ P 0*4 ○ ○ ○ ○ ○ @ P 1 0*4 ○ ○ ○ ○ ○ @ P 2 0*4 RESET switch ○ ○ ○ ○ ○ ○: Clear ×: Retain Operation Binary, Pental, Octal, Decimal, and Hexadecimal 11 Operations (N-base) –x Conversions can be performed between N-base numbers in NORMAL mode. The four basic arithmetic operations, calculations with parentheses, and memory calculations can also be performed, along with the logical operations AND, OR, NOT, NEG, XOR, and XNOR on binary, pental, octal, and hexadecimal numbers. Conversion to each system is performed with the following keys: @ z (“BIN” appears), @ r (“PEN” appears), @ g (“OCT” appears), @ h (“HEX” appears), @ / (“BIN”, “PEN”, “OCT”, and “HEX” disappear) Note: The hexadecimal numbers A–F are entered by pressing sx Sample standard deviation (x data) σx Population standard deviation (x data) n Number of samples A B C D E 13 • Before performing a calculation, select the angular unit. • The calculation result is automatically stored in the X and Y memories (r or x in X memory, and θ or y in Y memory). • The results of coordinate conversions will be displayed as decimal numbers even in the WriteView editor. Rectangular coord. Polar coord. Modify Function 14 Decimal calculation results are internally obtained in scientific notation, with up to 14 digits in the mantissa. However, since calculation results are displayed in the form designated by the display notation and the number of decimal places indicated, the internal calculation result may differ from that shown in the display. By using the modify function (@ n), the internal value is converted to match that of the display, so that the displayed value can be used without change in subsequent operations. • When using the WriteView editor, if the calculation result is displayed using fractions or irrational numbers, press U to convert it to decimal form first. STATISTICAL CALCULATIONS Displaying calculation results When possible, calculation results will be displayed using fractions, r, and π. When you press U, the display will cycle through the following display styles: improper fractions (with • Mixed fractions (with or without π) decimal numbers or without π) decimal numbers • Proper fractions (with or without π) • Irrational numbers (square roots, fractions made using square roots) decimal numbers Notes: • In the following cases, calculation results may be displayed using r: • Arithmetic operations and memory calculations • Trigonometric calculations • In trigonometric calculations, when Entry value entering values such as those in multiples of 15 the table to the right, results may be DEG 1 shown using r. RAD multiples of ⎯ 12 π • Calculation results may extend off 50 GRAD multiples of ⎯ 3 the edges of the screen. You can see those parts by pressing l or r (depending on whether the left or right portion is hidden). • Improper/proper fractions will be converted to and displayed as decimal numbers if the number of digits used in their expression is greater than nine. In the case of mixed fractions, the maximum number of displayable digits (including integers) is eight. • If the number of digits in the denominator of a fractional result that uses π is greater than three, the result is converted to and displayed as a decimal number. The Line Editor Entry and display In the Line editor, you can enter and display equations line by line. Notes: • Up to three lines of text may be viewed on the screen at one time. • If the length of the equation exceeds three lines, parts of it may be hidden from view after calculation. If you want to see the rest of the equation, press l or r to return to the editing screen. • In the Line editor, calculation results are displayed in decimal form. Back space and delete key To delete a number or function, move the cursor to the right of it, then press N. You can also delete a number or function that the cursor is directly over by pressing @ y. Multi-line Playback Function 2 This calculator is equipped with a function to recall previous equations and answers in NORMAL mode. A maximum of 340 characters can be stored in memory. When the memory is full, stored equations will be deleted to make room, starting with the oldest. Pressing u will display the previous equation. Further pressing u will display preceding equations (after returning to the previous equation, press d to view equations in order). In addition, @ u can be used to jump to the oldest equation, and @ d to jump to the newest one. • To edit an equation after recalling it, press l or r. • The multi-line memory will be cleared by the following operations: @ Z , mode change, RESET, N-base conversion, angular unit conversion, editor change (J 2 0 or J 2 1), and memory clear (@ P 1 0). Sum of squares of samples (x data) Mean of samples ( y data) To exit DRILL mode, press b and select another mode. sy Sample standard deviation ( y data) Using Math Drill and × Table σy Population standard deviation ( y data) Sum of samples (x data) 2 Σy Σy Sum of samples ( y data) 2 Sum of squares of samples ( y data) Σ xy Sum of products of samples (x, y) r Correlation coefficient a Coefficient of regression equation b Coefficient of regression equation c Coefficient of quadratic regression equation • Use ; and t to perform a variable calculation in STAT mode. • U does not function in STAT mode. 16 Data entry Single-variable data Data _ Data H frequency _ (To enter multiples of the same data) Two-variable data Data x H data y _ Data x H data y H frequency _ (To enter multiples of the same data x and y) Note: Up to 100 data items can be entered. With the singlevariable data, a data item without frequency assignment is counted as one data item, while an item assigned with frequency is stored as a set of two data items. With the two-variable data, a set of data items without frequency assignment is counted as two data items, while a set of items assigned with frequency is stored as a set of three data items. 1. Press b 2 0 for Math Drill or b 2 1 for × Table. 2. Math Drill: Use u and d to select the number of questions (25, 50, or 100). × Table: Use u and d to select a row in the multiplication table (1 to 12). 3. Math Drill: Use l and r to select the operator type for questions (+, −, ×, ÷, or +−×÷). × Table: Use l and r to select the order type (“Serial” or “Random”). 4. Press e to start. When using Math Drill or × Table (random order only), questions are randomly selected and will not repeat except by chance. 5. Enter your answer. Press j or N to clear the entered number and then enter the correct answer. 6. Press e. • If the answer is correct, “ ” appears and the next question is displayed. • If the answer is wrong, “ ”appears and the same question is displayed. This will be regarded as an incorrect answer. • If you press e without entering an answer, the correct answer is displayed and then the next question is displayed. This will be regarded as an incorrect answer. 7. Continue answering the series of questions by entering the answer and pressing e. 8. After you finish, press e and the number and percentage of correct answers are displayed. 9. Press e to return to the initial screen for your current drill. Math Drill sample Current question/ Total questions Question ⋮ Data correction Correction before pressing _ immediately after a data entry: Delete incorrect data with j, then enter the correct data. Correction after pressing _: Use u and d to display the previously entered data set. Press d to display the data set in ascending (oldest first) order. To reverse the display order to descending (latest first), press the u key. Press @ u or @ d to jump the cursor to the beginning or end of the data set. Each data set is displayed with “X:”, “Y:”, or “F:”. See step 6 above. ⋮ Number of questions Operator type Percentage correct Correct answers Data set number Data x Frequency Total remaining questions Question Data set number Data x Data y Frequency 15 The following statistics can be obtained for each statistical calculation (refer to the table below): Single-variable statistical calculation Statistics of ①. Linear regression calculation Statistics of ① and ②. In addition, the estimate of y for a given x (estimate y´) and the estimate of x for a given y (estimate x´). Quadratic regression calculation Statistics of ① and ②, and coefficients a, b, c in the quadratic regression formula ( y = a + bx + cx 2). (For quadratic regression calculations, no correlation coefficient (r) can be obtained.) When there are two x´ values, each value will be displayed with “1:” or “2:”, and stored separately in the X and Y memories. Euler exponential regression, logarithmic regression, power regression, inverse regression, and general exponential regression calculations Statistics of ① and ②. In addition, the estimate of y for a given x and the estimate of x for a given y. (Since the calculator converts each formula into a linear regression formula before actual calculation takes place, it obtains all statistics, except coefficients a and b, from converted data rather than entered data.) ⋮ See step 6 above. Display and move the cursor to the data item to be modified by using u and d, input the correct value, then press _ or e. • To delete a data set, display and move the cursor to an item of the data set to delete by using u and d, then press @ #. The data set will be deleted. • To add a new data set, press j to exit the display of previously entered data and input the values, then press _. Statistical Calculation Formulas Type Regression formula Linear y = a + bx Quadratic y = a + bx + cx 2 Euler exponential y = a ⋅ ebx Logarithmic y = a + b ⋅ ln x Power y = a ⋅ xb Inverse 1 y=a+b⎯ x General exponential y = a ⋅ bx An error will occur when: • The absolute value of the intermediate result or calculation result is equal to or greater than 1 × 10100. • The denominator is zero. • An attempt is made to take the square root of a negative number. • No solution exists in the quadratic regression calculation. Priority Levels in Calculation This calculator performs operations according to the following priority: ① Fractions (1m4, etc.) ② Functions preceded by their argument (x −1, x 2, n!, etc.) ③ y x, xr ④ Implied multiplication of a memory value (2Y, etc.) ⑤ Functions followed by their argument (sin, cos, 1 etc.) ⑥ Implied multiplication of a function (2sin 30, A ⎯ 4 , etc.) ⑦ nCr, nPr ⑧ ×, ÷ ⑨ +, − ⑩ AND ⑪ OR, XOR, XNOR ⑫ =, M+, M−, ⇒M, ▶DEG, ▶RAD, ▶GRAD, DATA, CD, r θ, xy, and other calculation ending instructions • If parentheses are used, parenthesized calculations have precedence over any other calculations. INITIAL SET UP Mode Selection NORMAL mode: b 0 (default) Used to perform arithmetic operations and function calculations. Multiplicand Order type Percentage correct Correct answers Ranges of Math Drill Questions The range of questions for each operator type is as follows. + Addition operator: “0 + 0” to “20 + 20” ] Subtraction operator: “0 − 0” to “20 − 20”; answers are positive integers and 0. > Multiplication operator: “1 × 0” or “0 × 1” to “12 × 12” ) Division operator: “0 ÷ 1” to “144 ÷ 12”; answers are positive integers from 1 to 12 and 0, dividends of up to 144, and divisors of up to 12. +]>) Mixed operators: Questions within all the above ranges are displayed. ERRORS AND CALCULATION RANGES Errors An error will occur if an operation exceeds the calculation ranges, or if a mathematically illegal operation is attempted. When an error occurs, pressing l or r automatically moves the cursor back to the place in the equation where the error occurred. Edit the equation or press j to clear the equation. Functions 6 • Refer to the calculation examples for each function. • In the Line editor, the following symbols are used: : to indicate an expression’s power. (m, @ ", • @ Y) • : to separate integers, numerators, and denominators. (W, @ k) • When using @ O or @ W in the Line editor, values are entered in the following way: • logn (base, value) • abs value Random Function The random function has four settings. (This function cannot be selected while using the N-base function.) To generate further random numbers in succession, press e. Press j to exit. Random numbers A pseudo-random number, with three significant digits from 0 up to 0.999, can be generated by pressing @ w 0 e. Note: In the WriteView editor, the result will be a fraction or 0. Random dice To simulate a die-rolling, a random integer between 1 and 6 can be generated by pressing @ w 1 e. Random coin To simulate a coin flip, 0 (heads) or 1 (tails) can be randomly generated by pressing @ w 2 e. STAT mode: b 1 Used to perform statistical operations. DRILL mode: b 2 Used to practice math and multiplication table drills. Random integer An integer between 0 and 99 can be generated randomly by pressing @ w 3 e. SET UP Menu Press J to display the SET UP menu. Press j to exit the SET UP menu. Angular Unit Conversions Determination of the angular unit The following three angular units (degrees, radians, and grads) can be specified. DEG (°): J 0 0 (default) RAD (rad): J 0 1 GRAD (g): J 0 2 Memory Calculations 3 Selecting the display notation and decimal places Five display notation systems are used to display calculation results: Two settings of Floating point (NORM1 and NORM2), Fixed decimal point (FIX), Scientific notation (SCI), and Engineering notation (ENG). • When J 1 0 (FIX) or J 1 2 (ENG) is pressed, “TAB(0–9)?” will be displayed and the number of decimal places (TAB) can be set to any value between 0 and 9. • When J 1 1 (SCI) is pressed, “SIG(0–9)?” will be displayed and the number of significant digits can be set to any value between 0 and 9. Entering 0 will set a 10-digit display. Setting the floating point number system in scientific notation Two settings are used to display a floating-point number: NORM1 (the default) and NORM2. A number is automatically displayed in scientific notation outside a preset range: • NORM1 (J 1 3): 0.000000001 ≤ | x | ≤ 9,999,999,999 • NORM2 (J 1 4): 0.01 ≤ | x | ≤ 9,999,999,999 Selecting the editor Two editors are available in NORMAL mode: • The WriteView editor (W-VIEW): J 2 0 (default) • The Line editor (LINE): J 2 1 Adjusting the display contrast Press J 3, then + or & to adjust the contrast. Press j to exit. Insert and overwrite entry methods When using the Line editor, you can change the entry method from “INSERT” (the default) to “OVERWRITE”. After you switch to the overwrite method (by pressing J 4 1), the triangular cursor will change to a rectangular one, and the number or function underneath it will be overwritten as you make entries. SCIENTIFIC CALCULATIONS • Press b 0 to select NORMAL mode. • In each example, press j to clear the display first. Unless otherwise specified, calculation examples are performed in the WriteView editor with the default display settings (@ P 0). Arithmetic Operations 4 • The closing parenthesis ) just before = or m may be omitted. Constant Calculations 5 • In constant calculations, the addend becomes a constant. Subtraction and division are performed in the same manner. For multiplication, the multiplicand becomes a constant. • In constant calculations, constants will be displayed as K. ERROR 02: Calculation error • The absolute value of an intermediate or final calculation result equals or exceeds 10100. • An attempt was made to divide by zero (or an intermediate calculation resulted in zero). • The calculation ranges were exceeded while performing calculations. Independent memory (M) In addition to all the features of temporary memories, a value can be added to or subtracted from an existing memory value. Press j x M to clear the independent memory (M). Last answer memory (ANS) The calculation result obtained by pressing = or any other calculation ending instruction is automatically stored in the last answer memory. Notes: • Calculation results from the functions indicated below are automatically stored in the X or Y memories replacing any existing values. r θ, xy: X memory (r or x), Y memory (θ or y) • • Two x´ values from a quadratic regression calculation in STAT mode: X memory (1:), Y memory (2:) • Use of t or ; will recall the value stored in memory using up to 14 digits. Definable memories (D1–D4) You can store functions or operations in definable memories (D1–D4). • To store a function or operation, press x, followed by a definable memory key (I, J, K, or L), followed by the operation you want to store. Menu-related operations, such as J, cannot be stored. Press j to return to the previous display. • To call a stored function or operation, press the corresponding memory key. Calling a stored function will do nothing if the function that is called would be unusable in the current context. • Any functions or operations that are stored in a definable memory will be replaced when you save a new one into that memory. • When displaying and correcting a data set in STAT mode, you cannot store functions or operations in definable memories. Chain Calculations 9 The previous calculation result can be used in the subsequent calculation. However, it cannot be recalled after entering multiple instructions. Fraction Calculations 10 Arithmetic operations and memory calculations can be performed using fractions. In NORMAL mode, conversion between a decimal number and a fraction can be performed by pressing U. Notes: • Improper/proper fractions will be converted to and displayed as decimal numbers if the number of digits used in their expression is greater than nine. In the case of mixed fractions, the maximum number of displayable digits (including integers) is eight. • To convert a sexagesimal value to a fraction, first convert it by pressing @ :. Replacement Procedure ERROR 03: Nesting error • The available number of buffers was exceeded. (There are 10 buffers for numeric values and 64 buffers for calculation instructions). ERROR 04: Data over • Data items exceeded 100 in STAT mode. 18 Cannot delete! • The selected item cannot be deleted by pressing N or @ y in the WriteView editor. Ex. * 5 r A l N In this example, delete the exponent before attempting to delete the parentheses. Cannot call! • The function or operation stored in definable memory (D1 to D4) cannot be called. Ex. An attempt was made to recall a statistical variable from within NORMAL mode. Buffer full! • The equation (including any calculation ending instructions) exceeded its maximum input buffer (159 characters in the WriteView editor or 161 characters in the Line editor). An equation may not exceed its maximum input buffer. Calculation Ranges 8 Memory calculations can be performed in NORMAL and STAT modes. Temporary memories (A–F, X and Y) Press x and a variable key to store a value in memory. Press t and a variable key to recall the value from that memory. To place a variable in an equation, press ; and a variable key. • If the product is not to be used for some time, to avoid damage to the unit from a leaking battery, remove it and store in a safe place. • Do not leave an exhausted battery inside the product. • Keep batteries out of the reach of children. • An exhausted battery left in the calculator may leak and damage the calculator. • Explosion risk may be caused by incorrect handling. • Do not throw batteries into a fire as they may explode. ERROR 01: Syntax error • An attempt was made to perform an invalid operation. Ex. 2 + & 5 = Alert Messages 7 Each time @ ] is pressed, the angular unit changes in sequence. 1. Turn the power off by pressing @ o. 2. Remove the two screws. (Fig. 1) 3. Slide the battery cover slightly and lift it to remove. 4. EL-W531/W531G/W535: Remove the used battery by prying it out with a ball-point pen or other similar pointed device. (Fig. 2) EL-W531H/W531HA: Remove the used battery. 5. EL-W531/W531G/W535: Install one new battery. Make sure the “+” side is facing up. EL-W531H/W531HA: Install one new battery. First insert the “−” side toward the spring. (Fig. 3) 6. Replace the cover and screws. 7. Press the RESET switch (on the back) with the tip of a ball-point pen or similar object. 8. Adjust the display contrast. See “Adjusting the Display Contrast”. • Make sure that the display appears as shown below. If the display does not appear as shown, remove the battery, reinstall it, and check the display once again. Fig. 1 Fig. 2 Fig. 3 19 • Within the ranges specified, this calculator is accurate to ±1 of the 10th digit of the mantissa. However, a calculation error increases in continuous calculations due to accumulation of each calculation error. (This is the same for y x, xr, n!, e x, ln, etc., where continuous calculations are performed internally.) Additionally, a calculation error will accumulate and become larger in the vicinity of inflection points and singular points of functions. • Calculation ranges ±10−99 to ±9.999999999 × 1099 and 0. If the absolute value of an entry or a final or intermediate result of a calculation is less than 10−99, the value is considered to be 0 in calculations and in the display. Automatic Power Off Function Display of results using r Calculation results may be displayed using r when all of the following conditions are met: • When intermediate and final calculation results are displayed in the following form: P b cP d ±a⎯ e ± ⎯ f • When each coefficient falls into the following ranges: 1 ≤ a < 100; 1 < b < 1,000; 0 ≤ c < 100; 1 ≤ d < 1,000; 1 ≤ e < 100; 1 ≤ f < 100 • When the number of terms in the intermediate and final calculation results is one or two. Note: The result of two fractional terms that include r will be reduced to a common denominator. Internal calculations: Mantissas of up to 14 digits Pending operations: 64 calculations 10 numeric values Power source: EL-W531/W535 1.5 V — … (DC): Alkaline battery (LR44 or equivalent) × 1 EL-W531G Built-in solar cells 1.5 V — … (DC): Backup battery (Alkaline battery (LR44 or equivalent) × 1) EL-W531H/W531HA 1.5 V — … (DC): Heavy duty manganese battery (size AAA or R03) × 1 Power consumption: EL-W531/W531H/W531HA/W535 0.00011 W Operating time: EL-W531/W535 (varies according to Approx. 3,000 hours when continuously use and other factors) displaying 55555. at 25°C (77°F) EL-W531G Approx. 3,000 hours when continuously displaying 55555. at 25°C (77°F), using the alkaline battery only EL-W531H/W531HA Approx. 17,000 hours when continuously displaying 55555. at 25°C (77°F) Operating temperature: 0°C–40°C (32°F–104°F) External dimensions: 79.6 mm (W) × 161.5 mm (D) × 15.5 mm (H) 3-1/8” (W) × 6-11/32” (D) × 5/8” (H) Weight: EL-W531/W535 Approx. 100 g (0.22 lb) (including battery) EL-W531G Approx. 102 g (0.23 lb) (including battery) EL-W531H/W531HA Approx. 107 g (0.24 lb) (including battery) Accessories: Battery × 1 (installed), operation manual, and hard case BATTERY REPLACEMENT Notes on Battery Replacement ⋮ 17 • Equations that have one result require an additional eleven characters’ worth of memory to store in order to hold the result. • In addition to the amount of memory needed to store an equation, the WriteView editor will require a certain amount for the sake of display. • Equations also include calculation ending instructions, such as “=”. Error codes and error types – y Σx ② Just after obtaining an answer, pressing l brings you to the end of the equation and pressing r brings you to the beginning. Press l, r, u, or d to move the cursor. Press @ l or @ r to jump the cursor to the beginning or the end of the equation. In the WriteView editor, you can use u and d to move the cursor up and down—between the numerator and denominator, for example. × Table sample Statistical calculations can be performed in STAT mode. There are eight sub-modes within STAT mode. Press b 1, then press the number key that corresponds to your choice: 0 (S#a# 0 [SD]): Single-variable statistics 1 (S#a# 1 [LINE]): Linear regression 2 (S#a# 2 [QUAD]): Quadratic regression 3 (S#a# 3 [E_EXP]): Euler exponential regression 4 (S#a# 4 [LOG]): Logarithmic regression 5 (S#a# 5 [POWER]): Power regression 6 (S#a# 6 [INV]): Inverse regression 7 (S#a# 7 [G_EXP]): General exponential regression Statistical Calculations and Variables Entry and display In the WriteView editor, you can enter and display fractions or certain functions as you would write them. Notes: • The WriteView editor can only be used in NORMAL mode. • If the equation grows too large, it may extend off the edge of the display after you obtain the result. If you want to see the entire equation, press l or r to return to the editing screen. Math Drill: b 2 0 Math operation questions with positive integers and 0 are displayed randomly. It is possible to select the number of questions and operator type. Before entering new data, clear the memory contents. Coordinate Conversions The WriteView Editor Multiplication Table (× Table): b 2 1 Questions from each row of the multiplication table (1 to 12) are displayed serially or randomly. Data Entry and Correction Second Minute 1 DRILL MODE Mean of samples (x data) Σx 12 Conversion between decimal and sexagesimal numbers can be performed. In addition, the four basic arithmetic operations and memory calculations can be performed using the sexagesimal system. Notation for sexagesimal is as follows: Degree ① F Time, Decimal, and Sexagesimal Calculations ENTERING, DISPLAYING, AND EDITING THE EQUATION Editing the Equation The WriteView editor (default) *1 Press j x and then choose a memory to clear one variable memory. *2 Definable memory. See “Memory Calculations”. *3 Statistical data (entered data) *4 See “Memory clear key”. *5 Cleared when changing between sub-modes in STAT mode. m , * , A , l , i , and H. In the binary, pental, octal, and hexadecimal systems, fractional parts cannot be entered. When a decimal number having a fractional part is converted into a binary, pental, octal, or hexadecimal number, the fractional part will be truncated. Likewise, when the result of a binary, pental, octal, or hexadecimal calculation includes a fractional part, the fractional part will be truncated. In the binary, pental, octal, and hexadecimal systems, negative numbers are displayed as a complement. Memory clear key Press @ P to display the menu. • To initialize the display settings, press 0. The parameters set as follows: • Angular unit: DEG • Display notation: NORM1 • N-base: DEC • To clear all variables and memories (A−F, M, X, Y, D1−D4, ANS, and STAT) at once, press 1 0. • To RESET the calculator, press 2 0. The RESET operation will erase all data stored in memory and restore the calculator’s default settings. Improper handling of batteries can cause electrolyte leakage or explosion. Be sure to observe the following handling rules: • Make sure the new battery is the correct type. • When installing, orient the battery properly as indicated in the calculator. • The battery is factory-installed before shipment, and may be exhausted before it reaches the service life stated in the specifications. Notes on erasure of memory contents When the battery is replaced, the memory contents are erased. Erasure can also occur if the calculator is defective or when it is repaired. Make a note of all important memory contents in case accidental erasure occurs. When to Replace the Battery EL-W531/W531H/W531HA/W535: If the display has poor contrast even after adjusting the display contrast, the battery requires replacement. EL-W531G: If the display has poor contrast or nothing appears on the display when j is pressed in dim lighting, even after adjusting the display contrast, it is time to replace the battery. Cautions • Fluid from a leaking battery accidentally entering an eye could result in serious injury. Should this occur, wash with clean water and immediately consult a doctor. • Should fluid from a leaking battery come in contact with your skin or clothes, immediately wash with clean water. This calculator will turn itself off to save battery power if no key is pressed for approximately 10 minutes. SPECIFICATIONS Calculation features: Scientific calculations, statistical calculations, etc. Drill features: Math Drill and Multiplication Table Display: 96 × 32 dot matrix liquid crystal display Display of calculation results: Mantissa: 10 digits Exponent: 2 digits FOR MORE INFORMATION ABOUT SCIENTIFIC CALCULATORS Visit our Web site. http://sharp-world.com/calculator/ DISPLAY ENGLISH SCIENTIFIC CALCULATOR Symbol EL-W531 EL-W531G EL-W531H EL-W531HA EL-W535 Dot matrix display Mantissa Exponent Thank you for purchasing the SHARP Scientific Calculator Model EL-W531/W531G/W531H/W531HA/W535. About the calculation examples (including some formulas and tables), refer to the reverse side of this English manual. Refer to the number on the right of each title in the manual for use. After reading this manual, store it in a convenient location for future reference. Notes: • Some of the models described in this manual may not be available in some countries. • This product uses a period as a decimal point. • During actual use, not all symbols are displayed at the same time. • Only the symbols required for the usage under instruction are shown in the display and calculation examples of this manual. Indicates that some contents are hidden in the / : / directions shown. 2ndF: Appears when @ is pressed, indicating that the functions shown in orange are enabled. HYP: Indicates that H has been pressed and the hyperbolic functions are enabled. If @ > is pressed, the symbols “2ndF HYP” appear, indicating that inverse hyperbolic functions are enabled. ALPHA: Indicates that ;, x or t has been pressed, and entry (recall) of memory contents and recall of statistics can be performed. DEG/RAD/GRAD: Indicates angular units. BUSY: Appears during the execution of a calculation. W-VIEW: Indicates that the WriteView editor is selected. M: Indicates that a numerical value is stored in the independent memory (M). ENG/SCI/FIX/N2/N1: Indicates the notation used to display a value and changes by SET UP menu. N1 is displayed on-screen as “NORM1”, and N2 as “NORM2”. Operational Notes BEFORE USING THE CALCULATOR MODEL OPERATION MANUAL PRINTED IN CHINA / IMPRIMÉ EN CHINE / IMPRESO EN CHINA 07BGK (TINSE1278EHZZ) INTRODUCTION • Do not carry the calculator around in your back pocket, as it may break when you sit down. The display is made of glass and is particularly fragile. • Keep the calculator away from extreme heat such as on a car dashboard or near a heater, and avoid exposing it to excessively humid or dusty environments. • Since this product is not waterproof, do not use it or store it where fluids, for example water, can splash onto it. Raindrops, water spray, juice, coffee, steam, perspiration, etc. will also cause malfunction. • Clean with a soft, dry cloth. Do not use solvents or a wet cloth. • Do not drop it or apply excessive force. • Never dispose of batteries in a fire. • Keep batteries out of the reach of children. • This product, including accessories, may change due to upgrading without prior notice. When using for the first time, press the RESET switch (on the back), with the tip of a ball-point pen or similar object. Adjusting the Display Contrast Press J 3, then + or & to adjust the contrast. Press j to exit. Power On and Off Press j to turn the calculator on. The data that was onscreen when the power was turned off will appear on the display. Press @ o to turn it off. Key Notations Used in this Manual In this manual, key operations are described as follows: To specify e x: @ " To specify ln: i To specify E: ; E NOTICE • SHARP strongly recommends that separate permanent written records be kept of all important data. Data may be lost or altered in virtually any electronic memory product under certain circumstances. Therefore, SHARP assumes no responsibility for data lost or otherwise rendered unusable whether as a result of improper use, repairs, defects, battery replacement, use after the specified battery life has expired, or any other cause. • SHARP will not be liable nor responsible for any incidental or consequential economic or property damage caused by misuse and/or malfunctions of this product and its peripherals, unless such liability is acknowledged by law. ♦ Press the RESET switch (on the back), with the tip of a ball-point pen or similar object, only in the following cases. Do not use an object with a breakable or sharp tip. Note that pressing the RESET switch erases all data stored in memory. • When using for the first time • After replacing the battery • To clear all memory contents • When an abnormal condition occurs and all keys are inoperative If service should be required on this calculator, use only a SHARP servicing dealer, SHARP approved service facility, or SHARP repair service where available. Hard Case Remove the hard case, holding it with your fingers in the positions shown below. • Functions that are printed in orange above the key require @ to be pressed first before the key. When you specify the memory, press ; first. Numbers for input values are not shown as keys, but as ordinary numbers. • Functions that are printed in gray adjacent to the keys are effective in specific modes. The WriteView and Line Editors This calculator has the following two editors in NORMAL mode: WriteView and Line. You can select between them in the SET UP menu. The Line editor Note: In certain calculation examples, where you see the o symbol, the key operations and calculation results are shown as they would appear in the Line editor. Clearing the Entry and Memories Entry A–F*1, D1–D4*2 ANS STAT*3 (Display) M, X, Y j ○ × × × × ○ × × ○ ○ @Z Mode selection (b) ○ × × × ×*5 ○ × × × × @ P 0*4 ○ ○ ○ ○ ○ @ P 1 0*4 ○ ○ ○ ○ ○ @ P 2 0*4 RESET switch ○ ○ ○ ○ ○ ○: Clear ×: Retain Operation Binary, Pental, Octal, Decimal, and Hexadecimal 11 Operations (N-base) –x Conversions can be performed between N-base numbers in NORMAL mode. The four basic arithmetic operations, calculations with parentheses, and memory calculations can also be performed, along with the logical operations AND, OR, NOT, NEG, XOR, and XNOR on binary, pental, octal, and hexadecimal numbers. Conversion to each system is performed with the following keys: @ z (“BIN” appears), @ r (“PEN” appears), @ g (“OCT” appears), @ h (“HEX” appears), @ / (“BIN”, “PEN”, “OCT”, and “HEX” disappear) Note: The hexadecimal numbers A–F are entered by pressing sx Sample standard deviation (x data) σx Population standard deviation (x data) n Number of samples A B C D E 13 • Before performing a calculation, select the angular unit. • The calculation result is automatically stored in the X and Y memories (r or x in X memory, and θ or y in Y memory). • The results of coordinate conversions will be displayed as decimal numbers even in the WriteView editor. Rectangular coord. Polar coord. Modify Function 14 Decimal calculation results are internally obtained in scientific notation, with up to 14 digits in the mantissa. However, since calculation results are displayed in the form designated by the display notation and the number of decimal places indicated, the internal calculation result may differ from that shown in the display. By using the modify function (@ n), the internal value is converted to match that of the display, so that the displayed value can be used without change in subsequent operations. • When using the WriteView editor, if the calculation result is displayed using fractions or irrational numbers, press U to convert it to decimal form first. STATISTICAL CALCULATIONS Displaying calculation results When possible, calculation results will be displayed using fractions, r, and π. When you press U, the display will cycle through the following display styles: improper fractions (with • Mixed fractions (with or without π) decimal numbers or without π) decimal numbers • Proper fractions (with or without π) • Irrational numbers (square roots, fractions made using square roots) decimal numbers Notes: • In the following cases, calculation results may be displayed using r: • Arithmetic operations and memory calculations • Trigonometric calculations • In trigonometric calculations, when Entry value entering values such as those in multiples of 15 the table to the right, results may be DEG 1 shown using r. RAD multiples of ⎯ 12 π • Calculation results may extend off 50 GRAD multiples of ⎯ 3 the edges of the screen. You can see those parts by pressing l or r (depending on whether the left or right portion is hidden). • Improper/proper fractions will be converted to and displayed as decimal numbers if the number of digits used in their expression is greater than nine. In the case of mixed fractions, the maximum number of displayable digits (including integers) is eight. • If the number of digits in the denominator of a fractional result that uses π is greater than three, the result is converted to and displayed as a decimal number. The Line Editor Entry and display In the Line editor, you can enter and display equations line by line. Notes: • Up to three lines of text may be viewed on the screen at one time. • If the length of the equation exceeds three lines, parts of it may be hidden from view after calculation. If you want to see the rest of the equation, press l or r to return to the editing screen. • In the Line editor, calculation results are displayed in decimal form. Back space and delete key To delete a number or function, move the cursor to the right of it, then press N. You can also delete a number or function that the cursor is directly over by pressing @ y. Multi-line Playback Function 2 This calculator is equipped with a function to recall previous equations and answers in NORMAL mode. A maximum of 340 characters can be stored in memory. When the memory is full, stored equations will be deleted to make room, starting with the oldest. Pressing u will display the previous equation. Further pressing u will display preceding equations (after returning to the previous equation, press d to view equations in order). In addition, @ u can be used to jump to the oldest equation, and @ d to jump to the newest one. • To edit an equation after recalling it, press l or r. • The multi-line memory will be cleared by the following operations: @ Z , mode change, RESET, N-base conversion, angular unit conversion, editor change (J 2 0 or J 2 1), and memory clear (@ P 1 0). Sum of squares of samples (x data) Mean of samples ( y data) To exit DRILL mode, press b and select another mode. sy Sample standard deviation ( y data) Using Math Drill and × Table σy Population standard deviation ( y data) Sum of samples (x data) 2 Σy Σy Sum of samples ( y data) 2 Sum of squares of samples ( y data) Σ xy Sum of products of samples (x, y) r Correlation coefficient a Coefficient of regression equation b Coefficient of regression equation c Coefficient of quadratic regression equation • Use ; and t to perform a variable calculation in STAT mode. • U does not function in STAT mode. 16 Data entry Single-variable data Data _ Data H frequency _ (To enter multiples of the same data) Two-variable data Data x H data y _ Data x H data y H frequency _ (To enter multiples of the same data x and y) Note: Up to 100 data items can be entered. With the singlevariable data, a data item without frequency assignment is counted as one data item, while an item assigned with frequency is stored as a set of two data items. With the two-variable data, a set of data items without frequency assignment is counted as two data items, while a set of items assigned with frequency is stored as a set of three data items. 1. Press b 2 0 for Math Drill or b 2 1 for × Table. 2. Math Drill: Use u and d to select the number of questions (25, 50, or 100). × Table: Use u and d to select a row in the multiplication table (1 to 12). 3. Math Drill: Use l and r to select the operator type for questions (+, −, ×, ÷, or +−×÷). × Table: Use l and r to select the order type (“Serial” or “Random”). 4. Press e to start. When using Math Drill or × Table (random order only), questions are randomly selected and will not repeat except by chance. 5. Enter your answer. Press j or N to clear the entered number and then enter the correct answer. 6. Press e. • If the answer is correct, “ ” appears and the next question is displayed. • If the answer is wrong, “ ”appears and the same question is displayed. This will be regarded as an incorrect answer. • If you press e without entering an answer, the correct answer is displayed and then the next question is displayed. This will be regarded as an incorrect answer. 7. Continue answering the series of questions by entering the answer and pressing e. 8. After you finish, press e and the number and percentage of correct answers are displayed. 9. Press e to return to the initial screen for your current drill. Math Drill sample Current question/ Total questions Question ⋮ Data correction Correction before pressing _ immediately after a data entry: Delete incorrect data with j, then enter the correct data. Correction after pressing _: Use u and d to display the previously entered data set. Press d to display the data set in ascending (oldest first) order. To reverse the display order to descending (latest first), press the u key. Press @ u or @ d to jump the cursor to the beginning or end of the data set. Each data set is displayed with “X:”, “Y:”, or “F:”. See step 6 above. ⋮ Number of questions Operator type Percentage correct Correct answers Data set number Data x Frequency Total remaining questions Question Data set number Data x Data y Frequency 15 The following statistics can be obtained for each statistical calculation (refer to the table below): Single-variable statistical calculation Statistics of ①. Linear regression calculation Statistics of ① and ②. In addition, the estimate of y for a given x (estimate y´) and the estimate of x for a given y (estimate x´). Quadratic regression calculation Statistics of ① and ②, and coefficients a, b, c in the quadratic regression formula ( y = a + bx + cx 2). (For quadratic regression calculations, no correlation coefficient (r) can be obtained.) When there are two x´ values, each value will be displayed with “1:” or “2:”, and stored separately in the X and Y memories. Euler exponential regression, logarithmic regression, power regression, inverse regression, and general exponential regression calculations Statistics of ① and ②. In addition, the estimate of y for a given x and the estimate of x for a given y. (Since the calculator converts each formula into a linear regression formula before actual calculation takes place, it obtains all statistics, except coefficients a and b, from converted data rather than entered data.) ⋮ See step 6 above. Display and move the cursor to the data item to be modified by using u and d, input the correct value, then press _ or e. • To delete a data set, display and move the cursor to an item of the data set to delete by using u and d, then press @ #. The data set will be deleted. • To add a new data set, press j to exit the display of previously entered data and input the values, then press _. Statistical Calculation Formulas Type Regression formula Linear y = a + bx Quadratic y = a + bx + cx 2 Euler exponential y = a ⋅ ebx Logarithmic y = a + b ⋅ ln x Power y = a ⋅ xb Inverse 1 y=a+b⎯ x General exponential y = a ⋅ bx An error will occur when: • The absolute value of the intermediate result or calculation result is equal to or greater than 1 × 10100. • The denominator is zero. • An attempt is made to take the square root of a negative number. • No solution exists in the quadratic regression calculation. Priority Levels in Calculation This calculator performs operations according to the following priority: ① Fractions (1m4, etc.) ② Functions preceded by their argument (x −1, x 2, n!, etc.) ③ y x, xr ④ Implied multiplication of a memory value (2Y, etc.) ⑤ Functions followed by their argument (sin, cos, 1 etc.) ⑥ Implied multiplication of a function (2sin 30, A ⎯ 4 , etc.) ⑦ nCr, nPr ⑧ ×, ÷ ⑨ +, − ⑩ AND ⑪ OR, XOR, XNOR ⑫ =, M+, M−, ⇒M, ▶DEG, ▶RAD, ▶GRAD, DATA, CD, r θ, xy, and other calculation ending instructions • If parentheses are used, parenthesized calculations have precedence over any other calculations. INITIAL SET UP Mode Selection NORMAL mode: b 0 (default) Used to perform arithmetic operations and function calculations. Multiplicand Order type Percentage correct Correct answers Ranges of Math Drill Questions The range of questions for each operator type is as follows. + Addition operator: “0 + 0” to “20 + 20” ] Subtraction operator: “0 − 0” to “20 − 20”; answers are positive integers and 0. > Multiplication operator: “1 × 0” or “0 × 1” to “12 × 12” ) Division operator: “0 ÷ 1” to “144 ÷ 12”; answers are positive integers from 1 to 12 and 0, dividends of up to 144, and divisors of up to 12. +]>) Mixed operators: Questions within all the above ranges are displayed. ERRORS AND CALCULATION RANGES Errors An error will occur if an operation exceeds the calculation ranges, or if a mathematically illegal operation is attempted. When an error occurs, pressing l or r automatically moves the cursor back to the place in the equation where the error occurred. Edit the equation or press j to clear the equation. Functions 6 • Refer to the calculation examples for each function. • In the Line editor, the following symbols are used: : to indicate an expression’s power. (m, @ ", • @ Y) • : to separate integers, numerators, and denominators. (W, @ k) • When using @ O or @ W in the Line editor, values are entered in the following way: • logn (base, value) • abs value Random Function The random function has four settings. (This function cannot be selected while using the N-base function.) To generate further random numbers in succession, press e. Press j to exit. Random numbers A pseudo-random number, with three significant digits from 0 up to 0.999, can be generated by pressing @ w 0 e. Note: In the WriteView editor, the result will be a fraction or 0. Random dice To simulate a die-rolling, a random integer between 1 and 6 can be generated by pressing @ w 1 e. Random coin To simulate a coin flip, 0 (heads) or 1 (tails) can be randomly generated by pressing @ w 2 e. STAT mode: b 1 Used to perform statistical operations. DRILL mode: b 2 Used to practice math and multiplication table drills. Random integer An integer between 0 and 99 can be generated randomly by pressing @ w 3 e. SET UP Menu Press J to display the SET UP menu. Press j to exit the SET UP menu. Angular Unit Conversions Determination of the angular unit The following three angular units (degrees, radians, and grads) can be specified. DEG (°): J 0 0 (default) RAD (rad): J 0 1 GRAD (g): J 0 2 Memory Calculations 3 Selecting the display notation and decimal places Five display notation systems are used to display calculation results: Two settings of Floating point (NORM1 and NORM2), Fixed decimal point (FIX), Scientific notation (SCI), and Engineering notation (ENG). • When J 1 0 (FIX) or J 1 2 (ENG) is pressed, “TAB(0–9)?” will be displayed and the number of decimal places (TAB) can be set to any value between 0 and 9. • When J 1 1 (SCI) is pressed, “SIG(0–9)?” will be displayed and the number of significant digits can be set to any value between 0 and 9. Entering 0 will set a 10-digit display. Setting the floating point number system in scientific notation Two settings are used to display a floating-point number: NORM1 (the default) and NORM2. A number is automatically displayed in scientific notation outside a preset range: • NORM1 (J 1 3): 0.000000001 ≤ | x | ≤ 9,999,999,999 • NORM2 (J 1 4): 0.01 ≤ | x | ≤ 9,999,999,999 Selecting the editor Two editors are available in NORMAL mode: • The WriteView editor (W-VIEW): J 2 0 (default) • The Line editor (LINE): J 2 1 Adjusting the display contrast Press J 3, then + or & to adjust the contrast. Press j to exit. Insert and overwrite entry methods When using the Line editor, you can change the entry method from “INSERT” (the default) to “OVERWRITE”. After you switch to the overwrite method (by pressing J 4 1), the triangular cursor will change to a rectangular one, and the number or function underneath it will be overwritten as you make entries. SCIENTIFIC CALCULATIONS • Press b 0 to select NORMAL mode. • In each example, press j to clear the display first. Unless otherwise specified, calculation examples are performed in the WriteView editor with the default display settings (@ P 0). Arithmetic Operations 4 • The closing parenthesis ) just before = or m may be omitted. Constant Calculations 5 • In constant calculations, the addend becomes a constant. Subtraction and division are performed in the same manner. For multiplication, the multiplicand becomes a constant. • In constant calculations, constants will be displayed as K. ERROR 02: Calculation error • The absolute value of an intermediate or final calculation result equals or exceeds 10100. • An attempt was made to divide by zero (or an intermediate calculation resulted in zero). • The calculation ranges were exceeded while performing calculations. Independent memory (M) In addition to all the features of temporary memories, a value can be added to or subtracted from an existing memory value. Press j x M to clear the independent memory (M). Last answer memory (ANS) The calculation result obtained by pressing = or any other calculation ending instruction is automatically stored in the last answer memory. Notes: • Calculation results from the functions indicated below are automatically stored in the X or Y memories replacing any existing values. r θ, xy: X memory (r or x), Y memory (θ or y) • • Two x´ values from a quadratic regression calculation in STAT mode: X memory (1:), Y memory (2:) • Use of t or ; will recall the value stored in memory using up to 14 digits. Definable memories (D1–D4) You can store functions or operations in definable memories (D1–D4). • To store a function or operation, press x, followed by a definable memory key (I, J, K, or L), followed by the operation you want to store. Menu-related operations, such as J, cannot be stored. Press j to return to the previous display. • To call a stored function or operation, press the corresponding memory key. Calling a stored function will do nothing if the function that is called would be unusable in the current context. • Any functions or operations that are stored in a definable memory will be replaced when you save a new one into that memory. • When displaying and correcting a data set in STAT mode, you cannot store functions or operations in definable memories. Chain Calculations 9 The previous calculation result can be used in the subsequent calculation. However, it cannot be recalled after entering multiple instructions. Fraction Calculations 10 Arithmetic operations and memory calculations can be performed using fractions. In NORMAL mode, conversion between a decimal number and a fraction can be performed by pressing U. Notes: • Improper/proper fractions will be converted to and displayed as decimal numbers if the number of digits used in their expression is greater than nine. In the case of mixed fractions, the maximum number of displayable digits (including integers) is eight. • To convert a sexagesimal value to a fraction, first convert it by pressing @ :. Replacement Procedure ERROR 03: Nesting error • The available number of buffers was exceeded. (There are 10 buffers for numeric values and 64 buffers for calculation instructions). ERROR 04: Data over • Data items exceeded 100 in STAT mode. 18 Cannot delete! • The selected item cannot be deleted by pressing N or @ y in the WriteView editor. Ex. * 5 r A l N In this example, delete the exponent before attempting to delete the parentheses. Cannot call! • The function or operation stored in definable memory (D1 to D4) cannot be called. Ex. An attempt was made to recall a statistical variable from within NORMAL mode. Buffer full! • The equation (including any calculation ending instructions) exceeded its maximum input buffer (159 characters in the WriteView editor or 161 characters in the Line editor). An equation may not exceed its maximum input buffer. Calculation Ranges 8 Memory calculations can be performed in NORMAL and STAT modes. Temporary memories (A–F, X and Y) Press x and a variable key to store a value in memory. Press t and a variable key to recall the value from that memory. To place a variable in an equation, press ; and a variable key. • If the product is not to be used for some time, to avoid damage to the unit from a leaking battery, remove it and store in a safe place. • Do not leave an exhausted battery inside the product. • Keep batteries out of the reach of children. • An exhausted battery left in the calculator may leak and damage the calculator. • Explosion risk may be caused by incorrect handling. • Do not throw batteries into a fire as they may explode. ERROR 01: Syntax error • An attempt was made to perform an invalid operation. Ex. 2 + & 5 = Alert Messages 7 Each time @ ] is pressed, the angular unit changes in sequence. 1. Turn the power off by pressing @ o. 2. Remove the two screws. (Fig. 1) 3. Slide the battery cover slightly and lift it to remove. 4. EL-W531/W531G/W535: Remove the used battery by prying it out with a ball-point pen or other similar pointed device. (Fig. 2) EL-W531H/W531HA: Remove the used battery. 5. EL-W531/W531G/W535: Install one new battery. Make sure the “+” side is facing up. EL-W531H/W531HA: Install one new battery. First insert the “−” side toward the spring. (Fig. 3) 6. Replace the cover and screws. 7. Press the RESET switch (on the back) with the tip of a ball-point pen or similar object. 8. Adjust the display contrast. See “Adjusting the Display Contrast”. • Make sure that the display appears as shown below. If the display does not appear as shown, remove the battery, reinstall it, and check the display once again. Fig. 1 Fig. 2 Fig. 3 19 • Within the ranges specified, this calculator is accurate to ±1 of the 10th digit of the mantissa. However, a calculation error increases in continuous calculations due to accumulation of each calculation error. (This is the same for y x, xr, n!, e x, ln, etc., where continuous calculations are performed internally.) Additionally, a calculation error will accumulate and become larger in the vicinity of inflection points and singular points of functions. • Calculation ranges ±10−99 to ±9.999999999 × 1099 and 0. If the absolute value of an entry or a final or intermediate result of a calculation is less than 10−99, the value is considered to be 0 in calculations and in the display. Automatic Power Off Function Display of results using r Calculation results may be displayed using r when all of the following conditions are met: • When intermediate and final calculation results are displayed in the following form: P b cP d ±a⎯ e ± ⎯ f • When each coefficient falls into the following ranges: 1 ≤ a < 100; 1 < b < 1,000; 0 ≤ c < 100; 1 ≤ d < 1,000; 1 ≤ e < 100; 1 ≤ f < 100 • When the number of terms in the intermediate and final calculation results is one or two. Note: The result of two fractional terms that include r will be reduced to a common denominator. Internal calculations: Mantissas of up to 14 digits Pending operations: 64 calculations 10 numeric values Power source: EL-W531/W535 1.5 V — … (DC): Alkaline battery (LR44 or equivalent) × 1 EL-W531G Built-in solar cells 1.5 V — … (DC): Backup battery (Alkaline battery (LR44 or equivalent) × 1) EL-W531H/W531HA 1.5 V — … (DC): Heavy duty manganese battery (size AAA or R03) × 1 Power consumption: EL-W531/W531H/W531HA/W535 0.00011 W Operating time: EL-W531/W535 (varies according to Approx. 3,000 hours when continuously use and other factors) displaying 55555. at 25°C (77°F) EL-W531G Approx. 3,000 hours when continuously displaying 55555. at 25°C (77°F), using the alkaline battery only EL-W531H/W531HA Approx. 17,000 hours when continuously displaying 55555. at 25°C (77°F) Operating temperature: 0°C–40°C (32°F–104°F) External dimensions: 79.6 mm (W) × 161.5 mm (D) × 15.5 mm (H) 3-1/8” (W) × 6-11/32” (D) × 5/8” (H) Weight: EL-W531/W535 Approx. 100 g (0.22 lb) (including battery) EL-W531G Approx. 102 g (0.23 lb) (including battery) EL-W531H/W531HA Approx. 107 g (0.24 lb) (including battery) Accessories: Battery × 1 (installed), operation manual, and hard case BATTERY REPLACEMENT Notes on Battery Replacement ⋮ 17 • Equations that have one result require an additional eleven characters’ worth of memory to store in order to hold the result. • In addition to the amount of memory needed to store an equation, the WriteView editor will require a certain amount for the sake of display. • Equations also include calculation ending instructions, such as “=”. Error codes and error types – y Σx ② Just after obtaining an answer, pressing l brings you to the end of the equation and pressing r brings you to the beginning. Press l, r, u, or d to move the cursor. Press @ l or @ r to jump the cursor to the beginning or the end of the equation. In the WriteView editor, you can use u and d to move the cursor up and down—between the numerator and denominator, for example. × Table sample Statistical calculations can be performed in STAT mode. There are eight sub-modes within STAT mode. Press b 1, then press the number key that corresponds to your choice: 0 (S#a# 0 [SD]): Single-variable statistics 1 (S#a# 1 [LINE]): Linear regression 2 (S#a# 2 [QUAD]): Quadratic regression 3 (S#a# 3 [E_EXP]): Euler exponential regression 4 (S#a# 4 [LOG]): Logarithmic regression 5 (S#a# 5 [POWER]): Power regression 6 (S#a# 6 [INV]): Inverse regression 7 (S#a# 7 [G_EXP]): General exponential regression Statistical Calculations and Variables Entry and display In the WriteView editor, you can enter and display fractions or certain functions as you would write them. Notes: • The WriteView editor can only be used in NORMAL mode. • If the equation grows too large, it may extend off the edge of the display after you obtain the result. If you want to see the entire equation, press l or r to return to the editing screen. Math Drill: b 2 0 Math operation questions with positive integers and 0 are displayed randomly. It is possible to select the number of questions and operator type. Before entering new data, clear the memory contents. Coordinate Conversions The WriteView Editor Multiplication Table (× Table): b 2 1 Questions from each row of the multiplication table (1 to 12) are displayed serially or randomly. Data Entry and Correction Second Minute 1 DRILL MODE Mean of samples (x data) Σx 12 Conversion between decimal and sexagesimal numbers can be performed. In addition, the four basic arithmetic operations and memory calculations can be performed using the sexagesimal system. Notation for sexagesimal is as follows: Degree ① F Time, Decimal, and Sexagesimal Calculations ENTERING, DISPLAYING, AND EDITING THE EQUATION Editing the Equation The WriteView editor (default) *1 Press j x and then choose a memory to clear one variable memory. *2 Definable memory. See “Memory Calculations”. *3 Statistical data (entered data) *4 See “Memory clear key”. *5 Cleared when changing between sub-modes in STAT mode. m , * , A , l , i , and H. In the binary, pental, octal, and hexadecimal systems, fractional parts cannot be entered. When a decimal number having a fractional part is converted into a binary, pental, octal, or hexadecimal number, the fractional part will be truncated. Likewise, when the result of a binary, pental, octal, or hexadecimal calculation includes a fractional part, the fractional part will be truncated. In the binary, pental, octal, and hexadecimal systems, negative numbers are displayed as a complement. Memory clear key Press @ P to display the menu. • To initialize the display settings, press 0. The parameters set as follows: • Angular unit: DEG • Display notation: NORM1 • N-base: DEC • To clear all variables and memories (A−F, M, X, Y, D1−D4, ANS, and STAT) at once, press 1 0. • To RESET the calculator, press 2 0. The RESET operation will erase all data stored in memory and restore the calculator’s default settings. Improper handling of batteries can cause electrolyte leakage or explosion. Be sure to observe the following handling rules: • Make sure the new battery is the correct type. • When installing, orient the battery properly as indicated in the calculator. • The battery is factory-installed before shipment, and may be exhausted before it reaches the service life stated in the specifications. Notes on erasure of memory contents When the battery is replaced, the memory contents are erased. Erasure can also occur if the calculator is defective or when it is repaired. Make a note of all important memory contents in case accidental erasure occurs. When to Replace the Battery EL-W531/W531H/W531HA/W535: If the display has poor contrast even after adjusting the display contrast, the battery requires replacement. EL-W531G: If the display has poor contrast or nothing appears on the display when j is pressed in dim lighting, even after adjusting the display contrast, it is time to replace the battery. Cautions • Fluid from a leaking battery accidentally entering an eye could result in serious injury. Should this occur, wash with clean water and immediately consult a doctor. • Should fluid from a leaking battery come in contact with your skin or clothes, immediately wash with clean water. This calculator will turn itself off to save battery power if no key is pressed for approximately 10 minutes. SPECIFICATIONS Calculation features: Scientific calculations, statistical calculations, etc. Drill features: Math Drill and Multiplication Table Display: 96 × 32 dot matrix liquid crystal display Display of calculation results: Mantissa: 10 digits Exponent: 2 digits FOR MORE INFORMATION ABOUT SCIENTIFIC CALCULATORS Visit our Web site. http://sharp-world.com/calculator/ DISPLAY ENGLISH SCIENTIFIC CALCULATOR Symbol EL-W531 EL-W531G EL-W531H EL-W531HA EL-W535 Dot matrix display Mantissa Exponent Thank you for purchasing the SHARP Scientific Calculator Model EL-W531/W531G/W531H/W531HA/W535. About the calculation examples (including some formulas and tables), refer to the reverse side of this English manual. Refer to the number on the right of each title in the manual for use. After reading this manual, store it in a convenient location for future reference. Notes: • Some of the models described in this manual may not be available in some countries. • This product uses a period as a decimal point. • During actual use, not all symbols are displayed at the same time. • Only the symbols required for the usage under instruction are shown in the display and calculation examples of this manual. Indicates that some contents are hidden in the / : / directions shown. 2ndF: Appears when @ is pressed, indicating that the functions shown in orange are enabled. HYP: Indicates that H has been pressed and the hyperbolic functions are enabled. If @ > is pressed, the symbols “2ndF HYP” appear, indicating that inverse hyperbolic functions are enabled. ALPHA: Indicates that ;, x or t has been pressed, and entry (recall) of memory contents and recall of statistics can be performed. DEG/RAD/GRAD: Indicates angular units. BUSY: Appears during the execution of a calculation. W-VIEW: Indicates that the WriteView editor is selected. M: Indicates that a numerical value is stored in the independent memory (M). ENG/SCI/FIX/N2/N1: Indicates the notation used to display a value and changes by SET UP menu. N1 is displayed on-screen as “NORM1”, and N2 as “NORM2”. Operational Notes BEFORE USING THE CALCULATOR MODEL OPERATION MANUAL PRINTED IN CHINA / IMPRIMÉ EN CHINE / IMPRESO EN CHINA 07BGK (TINSE1278EHZZ) INTRODUCTION • Do not carry the calculator around in your back pocket, as it may break when you sit down. The display is made of glass and is particularly fragile. • Keep the calculator away from extreme heat such as on a car dashboard or near a heater, and avoid exposing it to excessively humid or dusty environments. • Since this product is not waterproof, do not use it or store it where fluids, for example water, can splash onto it. Raindrops, water spray, juice, coffee, steam, perspiration, etc. will also cause malfunction. • Clean with a soft, dry cloth. Do not use solvents or a wet cloth. • Do not drop it or apply excessive force. • Never dispose of batteries in a fire. • Keep batteries out of the reach of children. • This product, including accessories, may change due to upgrading without prior notice. When using for the first time, press the RESET switch (on the back), with the tip of a ball-point pen or similar object. Adjusting the Display Contrast Press J 3, then + or & to adjust the contrast. Press j to exit. Power On and Off Press j to turn the calculator on. The data that was onscreen when the power was turned off will appear on the display. Press @ o to turn it off. Key Notations Used in this Manual In this manual, key operations are described as follows: To specify e x: @ " To specify ln: i To specify E: ; E NOTICE • SHARP strongly recommends that separate permanent written records be kept of all important data. Data may be lost or altered in virtually any electronic memory product under certain circumstances. Therefore, SHARP assumes no responsibility for data lost or otherwise rendered unusable whether as a result of improper use, repairs, defects, battery replacement, use after the specified battery life has expired, or any other cause. • SHARP will not be liable nor responsible for any incidental or consequential economic or property damage caused by misuse and/or malfunctions of this product and its peripherals, unless such liability is acknowledged by law. ♦ Press the RESET switch (on the back), with the tip of a ball-point pen or similar object, only in the following cases. Do not use an object with a breakable or sharp tip. Note that pressing the RESET switch erases all data stored in memory. • When using for the first time • After replacing the battery • To clear all memory contents • When an abnormal condition occurs and all keys are inoperative If service should be required on this calculator, use only a SHARP servicing dealer, SHARP approved service facility, or SHARP repair service where available. Hard Case Remove the hard case, holding it with your fingers in the positions shown below. • Functions that are printed in orange above the key require @ to be pressed first before the key. When you specify the memory, press ; first. Numbers for input values are not shown as keys, but as ordinary numbers. • Functions that are printed in gray adjacent to the keys are effective in specific modes. The WriteView and Line Editors This calculator has the following two editors in NORMAL mode: WriteView and Line. You can select between them in the SET UP menu. The Line editor Note: In certain calculation examples, where you see the o symbol, the key operations and calculation results are shown as they would appear in the Line editor. Clearing the Entry and Memories Entry A–F*1, D1–D4*2 ANS STAT*3 (Display) M, X, Y j ○ × × × × ○ × × ○ ○ @Z Mode selection (b) ○ × × × ×*5 ○ × × × × @ P 0*4 ○ ○ ○ ○ ○ @ P 1 0*4 ○ ○ ○ ○ ○ @ P 2 0*4 RESET switch ○ ○ ○ ○ ○ ○: Clear ×: Retain Operation Binary, Pental, Octal, Decimal, and Hexadecimal 11 Operations (N-base) –x Conversions can be performed between N-base numbers in NORMAL mode. The four basic arithmetic operations, calculations with parentheses, and memory calculations can also be performed, along with the logical operations AND, OR, NOT, NEG, XOR, and XNOR on binary, pental, octal, and hexadecimal numbers. Conversion to each system is performed with the following keys: @ z (“BIN” appears), @ r (“PEN” appears), @ g (“OCT” appears), @ h (“HEX” appears), @ / (“BIN”, “PEN”, “OCT”, and “HEX” disappear) Note: The hexadecimal numbers A–F are entered by pressing sx Sample standard deviation (x data) σx Population standard deviation (x data) n Number of samples A B C D E 13 • Before performing a calculation, select the angular unit. • The calculation result is automatically stored in the X and Y memories (r or x in X memory, and θ or y in Y memory). • The results of coordinate conversions will be displayed as decimal numbers even in the WriteView editor. Rectangular coord. Polar coord. Modify Function 14 Decimal calculation results are internally obtained in scientific notation, with up to 14 digits in the mantissa. However, since calculation results are displayed in the form designated by the display notation and the number of decimal places indicated, the internal calculation result may differ from that shown in the display. By using the modify function (@ n), the internal value is converted to match that of the display, so that the displayed value can be used without change in subsequent operations. • When using the WriteView editor, if the calculation result is displayed using fractions or irrational numbers, press U to convert it to decimal form first. STATISTICAL CALCULATIONS Displaying calculation results When possible, calculation results will be displayed using fractions, r, and π. When you press U, the display will cycle through the following display styles: improper fractions (with • Mixed fractions (with or without π) decimal numbers or without π) decimal numbers • Proper fractions (with or without π) • Irrational numbers (square roots, fractions made using square roots) decimal numbers Notes: • In the following cases, calculation results may be displayed using r: • Arithmetic operations and memory calculations • Trigonometric calculations • In trigonometric calculations, when Entry value entering values such as those in multiples of 15 the table to the right, results may be DEG 1 shown using r. RAD multiples of ⎯ 12 π • Calculation results may extend off 50 GRAD multiples of ⎯ 3 the edges of the screen. You can see those parts by pressing l or r (depending on whether the left or right portion is hidden). • Improper/proper fractions will be converted to and displayed as decimal numbers if the number of digits used in their expression is greater than nine. In the case of mixed fractions, the maximum number of displayable digits (including integers) is eight. • If the number of digits in the denominator of a fractional result that uses π is greater than three, the result is converted to and displayed as a decimal number. The Line Editor Entry and display In the Line editor, you can enter and display equations line by line. Notes: • Up to three lines of text may be viewed on the screen at one time. • If the length of the equation exceeds three lines, parts of it may be hidden from view after calculation. If you want to see the rest of the equation, press l or r to return to the editing screen. • In the Line editor, calculation results are displayed in decimal form. Back space and delete key To delete a number or function, move the cursor to the right of it, then press N. You can also delete a number or function that the cursor is directly over by pressing @ y. Multi-line Playback Function 2 This calculator is equipped with a function to recall previous equations and answers in NORMAL mode. A maximum of 340 characters can be stored in memory. When the memory is full, stored equations will be deleted to make room, starting with the oldest. Pressing u will display the previous equation. Further pressing u will display preceding equations (after returning to the previous equation, press d to view equations in order). In addition, @ u can be used to jump to the oldest equation, and @ d to jump to the newest one. • To edit an equation after recalling it, press l or r. • The multi-line memory will be cleared by the following operations: @ Z , mode change, RESET, N-base conversion, angular unit conversion, editor change (J 2 0 or J 2 1), and memory clear (@ P 1 0). Sum of squares of samples (x data) Mean of samples ( y data) To exit DRILL mode, press b and select another mode. sy Sample standard deviation ( y data) Using Math Drill and × Table σy Population standard deviation ( y data) Sum of samples (x data) 2 Σy Σy Sum of samples ( y data) 2 Sum of squares of samples ( y data) Σ xy Sum of products of samples (x, y) r Correlation coefficient a Coefficient of regression equation b Coefficient of regression equation c Coefficient of quadratic regression equation • Use ; and t to perform a variable calculation in STAT mode. • U does not function in STAT mode. 16 Data entry Single-variable data Data _ Data H frequency _ (To enter multiples of the same data) Two-variable data Data x H data y _ Data x H data y H frequency _ (To enter multiples of the same data x and y) Note: Up to 100 data items can be entered. With the singlevariable data, a data item without frequency assignment is counted as one data item, while an item assigned with frequency is stored as a set of two data items. With the two-variable data, a set of data items without frequency assignment is counted as two data items, while a set of items assigned with frequency is stored as a set of three data items. 1. Press b 2 0 for Math Drill or b 2 1 for × Table. 2. Math Drill: Use u and d to select the number of questions (25, 50, or 100). × Table: Use u and d to select a row in the multiplication table (1 to 12). 3. Math Drill: Use l and r to select the operator type for questions (+, −, ×, ÷, or +−×÷). × Table: Use l and r to select the order type (“Serial” or “Random”). 4. Press e to start. When using Math Drill or × Table (random order only), questions are randomly selected and will not repeat except by chance. 5. Enter your answer. Press j or N to clear the entered number and then enter the correct answer. 6. Press e. • If the answer is correct, “ ” appears and the next question is displayed. • If the answer is wrong, “ ”appears and the same question is displayed. This will be regarded as an incorrect answer. • If you press e without entering an answer, the correct answer is displayed and then the next question is displayed. This will be regarded as an incorrect answer. 7. Continue answering the series of questions by entering the answer and pressing e. 8. After you finish, press e and the number and percentage of correct answers are displayed. 9. Press e to return to the initial screen for your current drill. Math Drill sample Current question/ Total questions Question ⋮ Data correction Correction before pressing _ immediately after a data entry: Delete incorrect data with j, then enter the correct data. Correction after pressing _: Use u and d to display the previously entered data set. Press d to display the data set in ascending (oldest first) order. To reverse the display order to descending (latest first), press the u key. Press @ u or @ d to jump the cursor to the beginning or end of the data set. Each data set is displayed with “X:”, “Y:”, or “F:”. See step 6 above. ⋮ Number of questions Operator type Percentage correct Correct answers Data set number Data x Frequency Total remaining questions Question Data set number Data x Data y Frequency 15 The following statistics can be obtained for each statistical calculation (refer to the table below): Single-variable statistical calculation Statistics of ①. Linear regression calculation Statistics of ① and ②. In addition, the estimate of y for a given x (estimate y´) and the estimate of x for a given y (estimate x´). Quadratic regression calculation Statistics of ① and ②, and coefficients a, b, c in the quadratic regression formula ( y = a + bx + cx 2). (For quadratic regression calculations, no correlation coefficient (r) can be obtained.) When there are two x´ values, each value will be displayed with “1:” or “2:”, and stored separately in the X and Y memories. Euler exponential regression, logarithmic regression, power regression, inverse regression, and general exponential regression calculations Statistics of ① and ②. In addition, the estimate of y for a given x and the estimate of x for a given y. (Since the calculator converts each formula into a linear regression formula before actual calculation takes place, it obtains all statistics, except coefficients a and b, from converted data rather than entered data.) ⋮ See step 6 above. Display and move the cursor to the data item to be modified by using u and d, input the correct value, then press _ or e. • To delete a data set, display and move the cursor to an item of the data set to delete by using u and d, then press @ #. The data set will be deleted. • To add a new data set, press j to exit the display of previously entered data and input the values, then press _. Statistical Calculation Formulas Type Regression formula Linear y = a + bx Quadratic y = a + bx + cx 2 Euler exponential y = a ⋅ ebx Logarithmic y = a + b ⋅ ln x Power y = a ⋅ xb Inverse 1 y=a+b⎯ x General exponential y = a ⋅ bx An error will occur when: • The absolute value of the intermediate result or calculation result is equal to or greater than 1 × 10100. • The denominator is zero. • An attempt is made to take the square root of a negative number. • No solution exists in the quadratic regression calculation. Priority Levels in Calculation This calculator performs operations according to the following priority: ① Fractions (1m4, etc.) ② Functions preceded by their argument (x −1, x 2, n!, etc.) ③ y x, xr ④ Implied multiplication of a memory value (2Y, etc.) ⑤ Functions followed by their argument (sin, cos, 1 etc.) ⑥ Implied multiplication of a function (2sin 30, A ⎯ 4 , etc.) ⑦ nCr, nPr ⑧ ×, ÷ ⑨ +, − ⑩ AND ⑪ OR, XOR, XNOR ⑫ =, M+, M−, ⇒M, ▶DEG, ▶RAD, ▶GRAD, DATA, CD, r θ, xy, and other calculation ending instructions • If parentheses are used, parenthesized calculations have precedence over any other calculations. INITIAL SET UP Mode Selection NORMAL mode: b 0 (default) Used to perform arithmetic operations and function calculations. Multiplicand Order type Percentage correct Correct answers Ranges of Math Drill Questions The range of questions for each operator type is as follows. + Addition operator: “0 + 0” to “20 + 20” ] Subtraction operator: “0 − 0” to “20 − 20”; answers are positive integers and 0. > Multiplication operator: “1 × 0” or “0 × 1” to “12 × 12” ) Division operator: “0 ÷ 1” to “144 ÷ 12”; answers are positive integers from 1 to 12 and 0, dividends of up to 144, and divisors of up to 12. +]>) Mixed operators: Questions within all the above ranges are displayed. ERRORS AND CALCULATION RANGES Errors An error will occur if an operation exceeds the calculation ranges, or if a mathematically illegal operation is attempted. When an error occurs, pressing l or r automatically moves the cursor back to the place in the equation where the error occurred. Edit the equation or press j to clear the equation. Functions 6 • Refer to the calculation examples for each function. • In the Line editor, the following symbols are used: : to indicate an expression’s power. (m, @ ", • @ Y) • : to separate integers, numerators, and denominators. (W, @ k) • When using @ O or @ W in the Line editor, values are entered in the following way: • logn (base, value) • abs value Random Function The random function has four settings. (This function cannot be selected while using the N-base function.) To generate further random numbers in succession, press e. Press j to exit. Random numbers A pseudo-random number, with three significant digits from 0 up to 0.999, can be generated by pressing @ w 0 e. Note: In the WriteView editor, the result will be a fraction or 0. Random dice To simulate a die-rolling, a random integer between 1 and 6 can be generated by pressing @ w 1 e. Random coin To simulate a coin flip, 0 (heads) or 1 (tails) can be randomly generated by pressing @ w 2 e. STAT mode: b 1 Used to perform statistical operations. DRILL mode: b 2 Used to practice math and multiplication table drills. Random integer An integer between 0 and 99 can be generated randomly by pressing @ w 3 e. SET UP Menu Press J to display the SET UP menu. Press j to exit the SET UP menu. Angular Unit Conversions Determination of the angular unit The following three angular units (degrees, radians, and grads) can be specified. DEG (°): J 0 0 (default) RAD (rad): J 0 1 GRAD (g): J 0 2 Memory Calculations 3 Selecting the display notation and decimal places Five display notation systems are used to display calculation results: Two settings of Floating point (NORM1 and NORM2), Fixed decimal point (FIX), Scientific notation (SCI), and Engineering notation (ENG). • When J 1 0 (FIX) or J 1 2 (ENG) is pressed, “TAB(0–9)?” will be displayed and the number of decimal places (TAB) can be set to any value between 0 and 9. • When J 1 1 (SCI) is pressed, “SIG(0–9)?” will be displayed and the number of significant digits can be set to any value between 0 and 9. Entering 0 will set a 10-digit display. Setting the floating point number system in scientific notation Two settings are used to display a floating-point number: NORM1 (the default) and NORM2. A number is automatically displayed in scientific notation outside a preset range: • NORM1 (J 1 3): 0.000000001 ≤ | x | ≤ 9,999,999,999 • NORM2 (J 1 4): 0.01 ≤ | x | ≤ 9,999,999,999 Selecting the editor Two editors are available in NORMAL mode: • The WriteView editor (W-VIEW): J 2 0 (default) • The Line editor (LINE): J 2 1 Adjusting the display contrast Press J 3, then + or & to adjust the contrast. Press j to exit. Insert and overwrite entry methods When using the Line editor, you can change the entry method from “INSERT” (the default) to “OVERWRITE”. After you switch to the overwrite method (by pressing J 4 1), the triangular cursor will change to a rectangular one, and the number or function underneath it will be overwritten as you make entries. SCIENTIFIC CALCULATIONS • Press b 0 to select NORMAL mode. • In each example, press j to clear the display first. Unless otherwise specified, calculation examples are performed in the WriteView editor with the default display settings (@ P 0). Arithmetic Operations 4 • The closing parenthesis ) just before = or m may be omitted. Constant Calculations 5 • In constant calculations, the addend becomes a constant. Subtraction and division are performed in the same manner. For multiplication, the multiplicand becomes a constant. • In constant calculations, constants will be displayed as K. ERROR 02: Calculation error • The absolute value of an intermediate or final calculation result equals or exceeds 10100. • An attempt was made to divide by zero (or an intermediate calculation resulted in zero). • The calculation ranges were exceeded while performing calculations. Independent memory (M) In addition to all the features of temporary memories, a value can be added to or subtracted from an existing memory value. Press j x M to clear the independent memory (M). Last answer memory (ANS) The calculation result obtained by pressing = or any other calculation ending instruction is automatically stored in the last answer memory. Notes: • Calculation results from the functions indicated below are automatically stored in the X or Y memories replacing any existing values. r θ, xy: X memory (r or x), Y memory (θ or y) • • Two x´ values from a quadratic regression calculation in STAT mode: X memory (1:), Y memory (2:) • Use of t or ; will recall the value stored in memory using up to 14 digits. Definable memories (D1–D4) You can store functions or operations in definable memories (D1–D4). • To store a function or operation, press x, followed by a definable memory key (I, J, K, or L), followed by the operation you want to store. Menu-related operations, such as J, cannot be stored. Press j to return to the previous display. • To call a stored function or operation, press the corresponding memory key. Calling a stored function will do nothing if the function that is called would be unusable in the current context. • Any functions or operations that are stored in a definable memory will be replaced when you save a new one into that memory. • When displaying and correcting a data set in STAT mode, you cannot store functions or operations in definable memories. Chain Calculations 9 The previous calculation result can be used in the subsequent calculation. However, it cannot be recalled after entering multiple instructions. Fraction Calculations 10 Arithmetic operations and memory calculations can be performed using fractions. In NORMAL mode, conversion between a decimal number and a fraction can be performed by pressing U. Notes: • Improper/proper fractions will be converted to and displayed as decimal numbers if the number of digits used in their expression is greater than nine. In the case of mixed fractions, the maximum number of displayable digits (including integers) is eight. • To convert a sexagesimal value to a fraction, first convert it by pressing @ :. Replacement Procedure ERROR 03: Nesting error • The available number of buffers was exceeded. (There are 10 buffers for numeric values and 64 buffers for calculation instructions). ERROR 04: Data over • Data items exceeded 100 in STAT mode. 18 Cannot delete! • The selected item cannot be deleted by pressing N or @ y in the WriteView editor. Ex. * 5 r A l N In this example, delete the exponent before attempting to delete the parentheses. Cannot call! • The function or operation stored in definable memory (D1 to D4) cannot be called. Ex. An attempt was made to recall a statistical variable from within NORMAL mode. Buffer full! • The equation (including any calculation ending instructions) exceeded its maximum input buffer (159 characters in the WriteView editor or 161 characters in the Line editor). An equation may not exceed its maximum input buffer. Calculation Ranges 8 Memory calculations can be performed in NORMAL and STAT modes. Temporary memories (A–F, X and Y) Press x and a variable key to store a value in memory. Press t and a variable key to recall the value from that memory. To place a variable in an equation, press ; and a variable key. • If the product is not to be used for some time, to avoid damage to the unit from a leaking battery, remove it and store in a safe place. • Do not leave an exhausted battery inside the product. • Keep batteries out of the reach of children. • An exhausted battery left in the calculator may leak and damage the calculator. • Explosion risk may be caused by incorrect handling. • Do not throw batteries into a fire as they may explode. ERROR 01: Syntax error • An attempt was made to perform an invalid operation. Ex. 2 + & 5 = Alert Messages 7 Each time @ ] is pressed, the angular unit changes in sequence. 1. Turn the power off by pressing @ o. 2. Remove the two screws. (Fig. 1) 3. Slide the battery cover slightly and lift it to remove. 4. EL-W531/W531G/W535: Remove the used battery by prying it out with a ball-point pen or other similar pointed device. (Fig. 2) EL-W531H/W531HA: Remove the used battery. 5. EL-W531/W531G/W535: Install one new battery. Make sure the “+” side is facing up. EL-W531H/W531HA: Install one new battery. First insert the “−” side toward the spring. (Fig. 3) 6. Replace the cover and screws. 7. Press the RESET switch (on the back) with the tip of a ball-point pen or similar object. 8. Adjust the display contrast. See “Adjusting the Display Contrast”. • Make sure that the display appears as shown below. If the display does not appear as shown, remove the battery, reinstall it, and check the display once again. Fig. 1 Fig. 2 Fig. 3 19 • Within the ranges specified, this calculator is accurate to ±1 of the 10th digit of the mantissa. However, a calculation error increases in continuous calculations due to accumulation of each calculation error. (This is the same for y x, xr, n!, e x, ln, etc., where continuous calculations are performed internally.) Additionally, a calculation error will accumulate and become larger in the vicinity of inflection points and singular points of functions. • Calculation ranges ±10−99 to ±9.999999999 × 1099 and 0. If the absolute value of an entry or a final or intermediate result of a calculation is less than 10−99, the value is considered to be 0 in calculations and in the display. Automatic Power Off Function Display of results using r Calculation results may be displayed using r when all of the following conditions are met: • When intermediate and final calculation results are displayed in the following form: P b cP d ±a⎯ e ± ⎯ f • When each coefficient falls into the following ranges: 1 ≤ a < 100; 1 < b < 1,000; 0 ≤ c < 100; 1 ≤ d < 1,000; 1 ≤ e < 100; 1 ≤ f < 100 • When the number of terms in the intermediate and final calculation results is one or two. Note: The result of two fractional terms that include r will be reduced to a common denominator. Internal calculations: Mantissas of up to 14 digits Pending operations: 64 calculations 10 numeric values Power source: EL-W531/W535 1.5 V — … (DC): Alkaline battery (LR44 or equivalent) × 1 EL-W531G Built-in solar cells 1.5 V — … (DC): Backup battery (Alkaline battery (LR44 or equivalent) × 1) EL-W531H/W531HA 1.5 V — … (DC): Heavy duty manganese battery (size AAA or R03) × 1 Power consumption: EL-W531/W531H/W531HA/W535 0.00011 W Operating time: EL-W531/W535 (varies according to Approx. 3,000 hours when continuously use and other factors) displaying 55555. at 25°C (77°F) EL-W531G Approx. 3,000 hours when continuously displaying 55555. at 25°C (77°F), using the alkaline battery only EL-W531H/W531HA Approx. 17,000 hours when continuously displaying 55555. at 25°C (77°F) Operating temperature: 0°C–40°C (32°F–104°F) External dimensions: 79.6 mm (W) × 161.5 mm (D) × 15.5 mm (H) 3-1/8” (W) × 6-11/32” (D) × 5/8” (H) Weight: EL-W531/W535 Approx. 100 g (0.22 lb) (including battery) EL-W531G Approx. 102 g (0.23 lb) (including battery) EL-W531H/W531HA Approx. 107 g (0.24 lb) (including battery) Accessories: Battery × 1 (installed), operation manual, and hard case BATTERY REPLACEMENT Notes on Battery Replacement ⋮ 17 • Equations that have one result require an additional eleven characters’ worth of memory to store in order to hold the result. • In addition to the amount of memory needed to store an equation, the WriteView editor will require a certain amount for the sake of display. • Equations also include calculation ending instructions, such as “=”. Error codes and error types – y Σx ② Just after obtaining an answer, pressing l brings you to the end of the equation and pressing r brings you to the beginning. Press l, r, u, or d to move the cursor. Press @ l or @ r to jump the cursor to the beginning or the end of the equation. In the WriteView editor, you can use u and d to move the cursor up and down—between the numerator and denominator, for example. × Table sample Statistical calculations can be performed in STAT mode. There are eight sub-modes within STAT mode. Press b 1, then press the number key that corresponds to your choice: 0 (S#a# 0 [SD]): Single-variable statistics 1 (S#a# 1 [LINE]): Linear regression 2 (S#a# 2 [QUAD]): Quadratic regression 3 (S#a# 3 [E_EXP]): Euler exponential regression 4 (S#a# 4 [LOG]): Logarithmic regression 5 (S#a# 5 [POWER]): Power regression 6 (S#a# 6 [INV]): Inverse regression 7 (S#a# 7 [G_EXP]): General exponential regression Statistical Calculations and Variables Entry and display In the WriteView editor, you can enter and display fractions or certain functions as you would write them. Notes: • The WriteView editor can only be used in NORMAL mode. • If the equation grows too large, it may extend off the edge of the display after you obtain the result. If you want to see the entire equation, press l or r to return to the editing screen. Math Drill: b 2 0 Math operation questions with positive integers and 0 are displayed randomly. It is possible to select the number of questions and operator type. Before entering new data, clear the memory contents. Coordinate Conversions The WriteView Editor Multiplication Table (× Table): b 2 1 Questions from each row of the multiplication table (1 to 12) are displayed serially or randomly. Data Entry and Correction Second Minute 1 DRILL MODE Mean of samples (x data) Σx 12 Conversion between decimal and sexagesimal numbers can be performed. In addition, the four basic arithmetic operations and memory calculations can be performed using the sexagesimal system. Notation for sexagesimal is as follows: Degree ① F Time, Decimal, and Sexagesimal Calculations ENTERING, DISPLAYING, AND EDITING THE EQUATION Editing the Equation The WriteView editor (default) *1 Press j x and then choose a memory to clear one variable memory. *2 Definable memory. See “Memory Calculations”. *3 Statistical data (entered data) *4 See “Memory clear key”. *5 Cleared when changing between sub-modes in STAT mode. m , * , A , l , i , and H. In the binary, pental, octal, and hexadecimal systems, fractional parts cannot be entered. When a decimal number having a fractional part is converted into a binary, pental, octal, or hexadecimal number, the fractional part will be truncated. Likewise, when the result of a binary, pental, octal, or hexadecimal calculation includes a fractional part, the fractional part will be truncated. In the binary, pental, octal, and hexadecimal systems, negative numbers are displayed as a complement. Memory clear key Press @ P to display the menu. • To initialize the display settings, press 0. The parameters set as follows: • Angular unit: DEG • Display notation: NORM1 • N-base: DEC • To clear all variables and memories (A−F, M, X, Y, D1−D4, ANS, and STAT) at once, press 1 0. • To RESET the calculator, press 2 0. The RESET operation will erase all data stored in memory and restore the calculator’s default settings. Improper handling of batteries can cause electrolyte leakage or explosion. Be sure to observe the following handling rules: • Make sure the new battery is the correct type. • When installing, orient the battery properly as indicated in the calculator. • The battery is factory-installed before shipment, and may be exhausted before it reaches the service life stated in the specifications. Notes on erasure of memory contents When the battery is replaced, the memory contents are erased. Erasure can also occur if the calculator is defective or when it is repaired. Make a note of all important memory contents in case accidental erasure occurs. When to Replace the Battery EL-W531/W531H/W531HA/W535: If the display has poor contrast even after adjusting the display contrast, the battery requires replacement. EL-W531G: If the display has poor contrast or nothing appears on the display when j is pressed in dim lighting, even after adjusting the display contrast, it is time to replace the battery. Cautions • Fluid from a leaking battery accidentally entering an eye could result in serious injury. Should this occur, wash with clean water and immediately consult a doctor. • Should fluid from a leaking battery come in contact with your skin or clothes, immediately wash with clean water. This calculator will turn itself off to save battery power if no key is pressed for approximately 10 minutes. SPECIFICATIONS Calculation features: Scientific calculations, statistical calculations, etc. Drill features: Math Drill and Multiplication Table Display: 96 × 32 dot matrix liquid crystal display Display of calculation results: Mantissa: 10 digits Exponent: 2 digits FOR MORE INFORMATION ABOUT SCIENTIFIC CALCULATORS Visit our Web site. http://sharp-world.com/calculator/ o 3 ÷ 1000 = ENGLISH 1 EL-W531 EL-W531G EL-W531H EL-W531HA EL-W535 CALCULATION EXAMPLES ANWENDUNGSBEISPIELE EXEMPLES DE CALCUL EJEMPLOS DE CÁLCULO EXEMPLOS DE CÁLCULO ESEMPI DI CALCOLO REKENVOORBEELDEN PÉLDASZÁMÍTÁSOK PŘÍKLADY VÝPOČTŮ RÄKNEEXEMPEL LASKENTAESIMERKKEJÄ UDREGNINGSEKSEMPLER [NORM2] J14 3.b-03 [NORM1] J13 0.003 +&kz()S` 4 45 + 285 ÷ 3 = j 45 + 285 z 3 = 18 + 6 ⎯= 15 − 8 ( 18 + 6 ) z (15 & 8 = 42 × −5 + 120 = 42 k S 5 + 120 = (5 × 103) ÷ (4 × 10−3) = 5 ` 3 z 4 `S3= CONTOH-CONTOH PERHITUNGAN 34 + 57 = 34 + 57 = 45 + 57 = 45 = 68 × 25 = 68 k 25 = 2 5 j2W5r +W3r4 = 3 4 P 3 ×P 5 = 3 20 U 23 ⎯ 20 U 1.15 U 3 1⎯ 20 P 2 ÷3+P 5 ÷5= * 2 r z 3 + *5rz5= Q 2 ⎯ 2 v 45 = 0.707106781 U J01 2 @ ^ 0.5 = 2 ⎯ J 3 2.094395102 U ud 3(5+2)= 21. ②3×5+2= 3k5+2= 17. ③ (5 + 3) × 2 = ( 5 + 3) k 2 = @u 3 π cos ⎯ [rad] = 4 J02 @y1= 10. 5@c2= 500 × 25% = 500 k 25 @ a 120 ÷ 400 = ?% 120 z 400 @ a 500 + (500 × 25%) = 500 + 25 @ a 400 − (400 × 30%) = 400 & 30 @ a 125. 30. 625. 280. |5 − 9| = @W5&9= 4. o @W(5&9 )= 4. • • • • • • • • • • • • • @>t( 5 z 7 ) = 0.895879734 RAD ln 20 = i 20 = 2.995732274 log 50 = l 50 = 1.698970004 log2 16384 = @ O 2 r 16384 = @ O 2 H 16384 ) = e3 = @"3= 1÷e= 1z;V = 1 7 14. GRAD 14. 0.367879441 −100 ≤ θ ≤ 100 0 ≤ θ ≤ 200 13 ⎯ 42 0.309523809 8mS2r &3m4r k5A= 33'333.33333 o ¥26,510 = $? 26510 z t Y = 241. U 33m20 $2,750 = ¥? 2750 k t Y = r = 3 cm (r ⇒ Y) 3xY πr 2 = ? s;Y A=U 24 2 ⎯ 2⎯ 4 + 6 = 5 …(A) 302'500. 3. 28.27433388 24 z ( 4 + 6 )= 3 k ; < + 60 z;<= sinh−1 ⇒ D1 xI@>v sinh−1 0.5 = I 0.5 = 0.481211825 6 + 4 = ANS j6+4= 10. ANS + 5 = +5= 15. 8 × 2 = ANS 8k2= 16. ANS2 = A= 44 + 37 = ANS 44 + 37 = 1 5 32 ⎯ 256. 81. 9. *= j3@k1d2r +W4d3= 5 6 4⎯ 29 ⎯ 6 → [g] sin−1 0.8 @] 90. @] → [°] = [°] - 63 ⎯ 64 129599 ⎯ 64 -2'024.984375 8mS2& 3m4k5 A= → [°] 8 -2024 @ w 0.8 = 53.13010235 53.13010235 @] ;txmM<IJK L 8×2⇒M j8k2xM 24 ÷ (8 × 2) = 24 z ; M = (8 × 2) × 5 = ;Mk5= 16. 1 1⎯ 2 80. -2'024.984375 U -2024m63m64 U -129599m64 4.833333333 3W1W2+4W3= 4m5m6* 29m6 4.833333333 10 3 = @Y2W3= ( ⎯75 ) 7W5rm5= 5 = o 4.641588834 16807 ⎯ 3125 @q1W8= 1 ⎯ 2 * 64 W 225 = 8 ⎯ 15 2 ⎯4 = 3 2@1W3m4= 8 ⎯ 81 o 2@1W(3m4) = 1 64 ⎯ = 225 3 BIN 11001 110101100 @ h 1AC BIN @z BIN PEN @r PEN 3203 OCT @g OCT 654 DEC @/ (1010 − 100) × 11 = @z( 1010 & 100) k 11 = [BIN] BIN (111) → NEG d 111 = HEX (1FF) + OCT (512) = HEX (?) 2FEC − 2C9E ⇒ M1 +) 2000 − 1901 ⇒ M2 — M= 428. 10010 BIN BIN 1111111001 @ h 1FF @g+ 512 = OCT 1511 @h HEX 349 jxM @ h 2FEC & 2C9E m HEX 34E 2000 &1901 m HEX 6FF tM jxM A4D HEX 1011 AND 101 = @ z 1011 4 101 = [BIN] BIN 1 5A OR C3 = [HEX] @ h 5A p C3 = HEX NOT 10110 = [BIN] @zn 10110 = BIN 1111101001 24 XOR 4 = [OCT] @ g 24 x4= OCT B3 XNOR 2D = [HEX] @ h B3 C 2D = HEX FFFFFFFF61 → DEC @/ 12 DB 20 -159. [: [10] j 7 [ 31 [ 49.44 @ : 7°31’49.44” 123.678 [60] 12 ⎯ 23 1.2 W 2.3 = 1°2’3” ⎯= 2 1[2[3W2= 0(31 q1.5" 1 × 10 ⎯ = 2 × 103 1`3W2`3= 1 ⎯ 2 7⇒A j7xA 7. 4 ⎯= A 4W;A= 4 ⎯ 7 123.678 @ : 663 1250 7⎯ 123(40q40.8" 3h 30m 45s + 6h 45m 36s = [60] 3 [ 30 [ 45 + 6 [ 45 [ 36 = 1234°56’12” + 0°0’34.567” = [60] 1234 [ 56 [ 12 + 0 [ 0 [ 34.567 = 1234(56 q47." 3h 45m – 1.69h = [60] 3 [ 45 & 1.69 =@: 8m81 1.2 ⎯= 2.3 3 j@/ 25 @ z 16807m3125 7W5m5= ⎯= 8 3 BIN HEX (1AC) Wk 1 4 3⎯ + ⎯ = 2 3 zrgh/dn4 pxC DEC (25) 9 2 100. 11 2 5 3 × (A) + 60 ÷ (A) = ⎯ 1 J ⎯ 2 5 * 4m5m6 = 4 ⎯ 6 2⎯ U j 90 @ ] 1.65 1m13m20 o ] 1.25 + 2 W 5 = U U 7 o 110. 0 ≤ θ ≤ 180 0≤θ≤π 1.65 110 x Y θ = cos−1 x π ≤θ≤⎯ π −⎯ 2 2 U $1 = ¥110 (110 ⇒ Y) U 90° → [rad] 20.08553692 U 8−2 − 34 × 52 = 35. U 5 tanh−1 ⎯ = 33 ⎯ 20 665. • −90 ≤ θ ≤ 90 U tM 10 θ = sin−1 x, θ = tan−1 x 13 20 1⎯ 250. tMk5@a @M ANS = 59.03344706 33.33b03 sin 62°12’24” = [10] v 62 [ 12 [ 24 = 13 10(16 q21." 2(3q36." 0.884635235 uEH ( ( rθ == [°] ( rθ == 1436 [°] ( xy == x=6 y=4 j6H4 @u r: {: 7.211102551 33.69006753 14 H 36 @E X: Y: 11.32623792 8.228993532 33'333.33333 J13 nJ S#a# 2 [QUAD] b12 18 0. x y 12 41 5 ⎯ 9 12 H 41 _ DATA SET= 1. 8 13 8 H 13 _ DATA SET= 2. 0.6 5 2 5H2_ DATA SET= 3. 1 k9=* 5.0 23 200 23 H 200 _ DATA SET= 4. 5z9= 5 ⎯ 9 15 71 15 H 71 _ DATA SET= 5. [FIX, TAB = 1] j J 1 0 1 0.0 5z9= U U 0.6 a= ta a= 5.357506761 3 ⎯ 5 b= tb b= -3.120289663 2 5 c= @n 5⎯ k 9 = *2 5.4 UU 5.4 J13 5 *1 ⎯ × 9 = 5.5555555555555 × 10−1 × 9 9 3 2 ⎯ * × 9 = 0.6 × 9 5 x = 10 y = 22 16 tS b 1 0 S#a# 0 [SD] @Z y´ = ? 10 @ U 10 y´ x´ = ? 22 @ V 22 x´ 1: 2: DATA 20 0. 40 DATA SET= 1. 40 80 80 _ DATA SET= 2. 50 80 75 75 75 50 _ DATA SET= 3. DATA SET= 5. 45 – x = 75.71428571 45 σx = tp σx = 12.37179148 45 n= Σx = tg Σx= Σx2 = to tv sx= 7. 530. 41'200. S#a# 1 [LINE] 0. y 2 5 2H5_ DATA SET= 1. 2 5 _ DATA SET= 2. 12 24 12 H 24 _ DATA SET= 3. 21 21 21 40 40 40 21 H 40 H 3 _ DATA SET= 4. 15 25 15 H 25 _ DATA SET= 5. a= ta a= 1.050261097 b= tb b= 1.826044386 r= tf r= 0.995176343 sx = tv sx = 8.541216597 sy = tG sy = 15.67223812 6.528394256 x=3 y´ = ? 3 @ U 3 y´ y = 46 x´ = ? 46 @ V 46 x´ 24.61590706 F: ■ 3_ X: d 60 _ 17 –x = Σ ⎯x σx = n x 2 − nx– 2 Σ⎯ n−1 sx = n 64.43210706 DATA SET= d d d 45 _ X: Σy – y= ⎯ ( 95 & ;R) ⎯ × 10 + 50 = z ; v sx k 10 + 50 = (95 − – x) DATA SET= d@# 60 13.3630621 sx2 = 178.5714286 A= DATA SET= 50 _ 4. tR DATA SET= 40 H 2 _ 75 H 3 _ DATA SET= – x = DATA SET= 30 _ DATA 30 tc 9.63201409 -3.432772026 S#a# 0 [SD] 20 _ 30 95 _ n= 24.4880159 _Hud# DATA 95 50 _ 0.503334057 c= b10 _HRvpcgoQ GsijhfabS VU x 720. @] [ENG: TAB 2] J 1 2 2 b11 24. → [g] 3.3b04 sx2 = 3. 6@Z+7 @Z= [SCI: SIG 2] J 1 1 2 DATA 50. U sx = @ q 27 = • U Σx2 = 4. 10 @ e 3 = = DEG DATA 15 = (cosh 1.5 + sinh 1.5)2 = j ( H $ 1.5 + H v 1.5 ) A = 20.08553692 7 * 49 & 4 @ D 81 = 4@B= 10P3 5C2 – M= 1 6 33'333.33 [NORM1] 4! = 4. ⎯+⎯= [FIX: TAB 2] J 1 0 2 ANS × 9 = 27 = 3p * 49 r & 4 @ D 81 = 2 1.25 + ⎯ = 1.25 + 2 W 5 = 5 450. 150 k 3 m +) $250: M1 + 250 ⇒ M2 250 m −) M2 × 5% 21. 17. j 100000 z 3 = o J00 J [MDF] 0.707106781 U tan−11 [g] = Q 2 ⎯ 2 p 49 − 4p 81 = $150 × 3 ⇒ M1 512. 0.927295218 ③ ANS × 9 = 0.866025403 8@1= @] 16. 5 ÷ 9 = ANS ⎯ 2 J01 $sW4= o 100000 ÷ 3 = 14 Q 3 83 = 6.447419591 → [rad] d [NORM1] 0. ( 12 m 3 ) m 1 W 4 = 6.447419591 @ Y 1.7 = 50.11872336 17. [NORM1] 2'720. o 0. jxM 0⇒M 101.7 = d u 1'700. ( 12 m 3 r)m 1W4= 16. ② ② 102. U o ① 3(5 + 2) = 91. j v 60 = 0. @Z ① sin 60 [°] = 3Q 5+5Q 2 ⎯ 15 0.918618116 U 2 1'250'000. @P0 H 15 3.872983346 U 2cos−1 0.5 [rad] = -90 40 = 1⎯ *3rk*5 = sin 45 = 3 7 3⎯ v$tw^ysH> ilO" VYZA1 *mDqBecaW H 6 U ⎯+⎯= 140. 5 68 × 40 = 1 0.003 j 3 z 1000 = [NORM1] (123) ⎯ 4 = sy = –2 Σ y 2 − ny ⎯ n−1 x 2 − nx– 2 Σ⎯ n Σx = x1 + x2 + … + xn Σx2 = x1 2 + x2 2 + … + xn2 Σy − 2 ny– 2 ⎯ n Σxy = x1 y1 + x2 y2 + … + xn yn Σy = y1 + y2 + … + yn Σy 2 = y1 2 + y2 2 + … + yn2 σy = Function keys Display Buffer space* Funktionstasten Anzeige Pufferplatz* Touches de fonction Affichage Espace tampon* Visualizador Espacio de memoria intermedia* Teclas de función Exibição Espaço na memória intermediária* Teclas de função Memoria tampone* Display Tasti di funzione Bufferruimte* Display Functietoetsen Pufferterület* Kijelző Függvénybillentyűk Vyrovnávací paměť* Zobrazení Tlačítka funkcí Buffertutrymme* Visning Funktionstangenter Puskuritila* Näyttö Funktionäppäimet Bufferplads* Display Funktionstaster * Tombol fungsi Function Funktion Fonction Función Função Funzioni Functie Függvény Funkce Funktion Funktio Funktion Dynamic range zulässiger Bereich Plage dynamique Rango dinámico Gama dinâmica Campi dinamici Rekencapaciteit Megengedett számítási tartomány Dynamický rozsah Definitionsområde Dynaaminen ala Dynamikområde Fungsi Kisaran dinamis Tampilan Ruang buffer* @Z □−1 1 A □2 1 @1 □3 1 m □□ 5 @O log□(□) 7 @" e□ 5 sin–1 x, cos–1 x |x| ≤ 1 5 tan x, P x | x | < 10100 ln x, log x, loga x 10–99 ≤ x < 10100, 10–99 ≤ a < 10100 (a ≠ 1) 10□ @Y 0. * P □ 5 1. @q 3P □ 5 □P 7 sin x, cos x, tan x DEG: | x | < 1010 (tan x : | x | ≠ 90(2n − 1))* π ⎯ RAD: | x | < 180 × 1010 π (tan x: | x | ≠ ⎯ (2n − 1))* 2 10 10 GRAD: | x | < ⎯ 9 × 10 (tan x: | x | ≠ 100(2n − 1))* –1 3 • y > 0: −10100 < x log y < 100 • y = 0: 0 < x < 10100 2. @D 3. W/@k □ ⎯ □ 7 (0 < | x | < 1: ⎯ x = 2n − 1, x ≠ 0)*, @W |□| 5 −10100 < x log | y | < 100 () ( 4 4. 3. 45. 3. 60. NOT BIN: 1000000000 ≤ x ≤ 1111111111 0 ≤ x ≤ 111111111 PEN: 2222222223 ≤ x ≤ 4444444444 0 ≤ x ≤ 2222222221 OCT: 4000000000 ≤ x ≤ 7777777777 0 ≤ x ≤ 3777777777 HEX: FDABF41C01 ≤ x ≤ FFFFFFFFFF 0 ≤ x ≤ 2540BE3FE NEG BIN: 1000000001 ≤ x ≤ 1111111111 0 ≤ x ≤ 111111111 PEN: 2222222223 ≤ x ≤ 4444444444 0 ≤ x ≤ 2222222222 OCT: 4000000001 ≤ x ≤ 7777777777 0 ≤ x ≤ 3777777777 HEX: FDABF41C01 ≤ x ≤ FFFFFFFFFF 0 ≤ x ≤ 2540BE3FF 19 □ ) * The amount of memory used for the sake of display in the WriteView editor, measured in characters (excluding entered values, denoted in the chart by “□”). * Der für die Anzeige in WriteView Editor verwendete Speicherplatz, gemessen in Zeichen (ohne die eingegebenen Werte, die in der Tabelle mit „□“ markiert sind). * Espace mémoire utilisé pour préserver l’affichage dans l’éditeur WriteView, mesuré en caractère (à l’exception des valeurs d’entrée, indiquées dans le tableau par “□”). * La cantidad de memoria usada para visualizar en el editor Write View, medida en caracteres (excluyendo los valores introducidos, indicados en el grafico mediante “□”). * A quantidade de memória que é usada para a exibição no editor WriteView, medida em caracteres (excluindo os valores introduzidos, indicados no quadro por “□”). * La quantità di memoria utilizzata per la visualizzazione nell’editor WriteView, misurata in caratteri (escludendo i valori inseriti, indicati nella tabella con il simbolo “□”). * De hoeveelheid geheugen dat wordt gebruikt om de WriteView editor weer te geven, gemeten in symbolen (met uitzondering van ingevoerde waarden aangeduid in de grafiek met “□”). * A WriteView szerkesztő megjelenítési műveleteire használatos memóriaterület, karakterben kifejezve (az ábrán „□” karakterrel jelölt beviteli értékeket nem számítva). * Množství paměti využívané pro účely zobrazení v editoru WriteView, vyjádřené počtem znaků (vyjma zadaných hodnot, označených v grafu znakem „□“). * Den mängd minne som används för visning med WriteViewredigeraren, mätt i antalet tecken (exklusive inmatade värden, vilka anges som ”□” i tabellen). * Näytön WriteView-editorissa käyttämä muisti merkkeinä laskettuna (pois lukien syötetyt arvot, taulukossa merkitty ”□”). * Den mængde hukommelse, der bruges til visning i WriteVieweditoren, målt i tegn (med undtagelse af indtastede værdier, der angives med „□“ i tabellen). x=n 1 1 −10100 < ⎯ x log y < 100 (x ≠ 0) • y = 0: 0 < x < 10100 • y < 0: x = 2n − 1 1 (0 < | x | < 1: ⎯ x = n, x ≠ 0)*, • y > 0: x y P 1 −10100 < ⎯ x log | y | < 100 ex −10100 < x ≤ 230.2585092 10 x −10100 < x < 100 sinh x, cosh x, tanh x | x | ≤ 230.2585092 sinh x | x | < 1050 cosh–1 x 1 ≤ x < 1050 –1 |x| < 1 x2 | x | < 1050 x3 | x | < 2.15443469 × 1033 x P 0 ≤ x < 10100 x –1 | x | < 10100 (x ≠ 0) n! 0 ≤ n ≤ 69* 0 ≤ r ≤ n ≤ 9999999999* n! ⎯ (n − r)! nPr Umweltschutz Das Gerät wird durch eine Batterie mit Strom versorgt. Um die Batterie sicher und umweltschonend zu entsorgen, beachten Sie bitte folgende Punkte: • Bringen Sie die leere Batterie zu Ihrer örtlichen Mülldeponie, zum Händler oder zum KundenserviceZentrum zur Wiederverwertung. • Werfen Sie die leere Batterie niemals ins Feuer, ins Wasser oder in den Hausmüll. Seulement pour la France/For France only: Protection de l’environnement L’appareil est alimenté par pile. Afin de protéger l’environnement, nous vous recommandons: • d’apporter la pile usagée ou à votre revendeur ou au service après-vente, pour recyclage. • de ne pas jeter la pile usagée dans une source de chaleur, dans l’eau ou dans un vide-ordures. Endast svensk version/For Sweden only: Miljöskydd Denna produkt drivs av batteri. Vid batteribyte skall följande iakttagas: • Det förbrukade batteriet skall inlämnas till batteriinsamling eller till kommunal miljöstation för återinssamling. • Kasta ej batteriet i vattnet eller i hushållssoporna. Batteriet får ej heller utsättas för öppen eld. OPMERKING: ALLEEN VOOR NEDERLAND/ NOTE: FOR NETHERLANDS ONLY 100 0 ≤ r ≤ n ≤ 9999999999* 0 ≤ r ≤ 69 nCr n! ⎯ (n − r)! ↕DEG, D°M’S r, θ < 10 Nur für Deutschland/For Germany only: For Europe only: tanh x –1 x, y * Jumlah memori yang digunakan untuk kepentingan tampilan dalam editor WriteView, diukur dalam jumlah karakter (tidak termasuk nilai yang dimasukkan, ditunjukkan dalam diagram dengan “□”) • y < 0: yx * n, r: integer / ganze Zahlen / entier / entero / inteiro / intero / geheel getal / egész számok / celé číslo / heltal / kokonaisluku / heltal / / / bilangan bulat r, θ x, y < 10100 0°0’0.00001” ≤ | x | < 10000° x 2 + y 2 < 10100 0 ≤ r < 10100 DEG: | θ | < 1010 π ⎯ RAD: | θ | < 180 × 1010 10 10 GRAD: | θ | < ⎯ 9 × 10 DEG DRG▶ DEC BIN PEN OCT HEX AND OR XOR XNOR RAD RAD, GRAD DEG: | x | < 10100 π GRAD: | x | < ⎯ 1098 2 × DEC: | x | ≤ 9999999999 BIN: 1000000000 ≤ x ≤ 1111111111 0 ≤ x ≤ 111111111 PEN: 2222222223 ≤ x ≤ 4444444444 0 ≤ x ≤ 2222222222 OCT: 4000000000 ≤ x ≤ 7777777777 0 ≤ x ≤ 3777777777 HEX: FDABF41C01 ≤ x ≤ FFFFFFFFFF 0 ≤ x ≤ 2540BE3FF A. Information on Disposal for Users (private households) 1. In the European Union Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin! Used electrical and electronic equipment must be treated separately and in accordance Attention: Your product with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment. is marked with this Following the implementation by member states, private households within the EU states symbol. It means that may return their used electrical and electronic equipment to designated collection facilities used electrical and free of charge*. In some countries* your local retailer may also take back your old product electronic products free of charge if you purchase a similar new one. should not be mixed with general household *) Please contact your local authority for further details. waste. There is a If your used electrical or electronic equipment has batteries or accumulators, please separate collection dispose of these separately beforehand according to local requirements. system for these By disposing of this product correctly you will help ensure that the waste undergoes the products. necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due to inappropriate waste handling. 2. In other Countries outside the EU If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal. For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch. ENGLISH B. Information on Disposal for Business Users. 1. In the European Union If the product is used for business purposes and you want to discard it: Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection facilities. For Spain: Please contact the established collection system or your local authority for take-back of your used products. 2. In other Countries outside the EU If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal. For Australia/New Zealand only: For warranty information please see www.sharp.net.au. o 3 ÷ 1000 = ENGLISH 1 EL-W531 EL-W531G EL-W531H EL-W531HA EL-W535 CALCULATION EXAMPLES ANWENDUNGSBEISPIELE EXEMPLES DE CALCUL EJEMPLOS DE CÁLCULO EXEMPLOS DE CÁLCULO ESEMPI DI CALCOLO REKENVOORBEELDEN PÉLDASZÁMÍTÁSOK PŘÍKLADY VÝPOČTŮ RÄKNEEXEMPEL LASKENTAESIMERKKEJÄ UDREGNINGSEKSEMPLER [NORM2] J14 3.b-03 [NORM1] J13 0.003 +&kz()S` 4 45 + 285 ÷ 3 = j 45 + 285 z 3 = 18 + 6 ⎯= 15 − 8 ( 18 + 6 ) z (15 & 8 = 42 × −5 + 120 = 42 k S 5 + 120 = (5 × 103) ÷ (4 × 10−3) = 5 ` 3 z 4 `S3= CONTOH-CONTOH PERHITUNGAN 34 + 57 = 34 + 57 = 45 + 57 = 45 = 68 × 25 = 68 k 25 = 2 5 j2W5r +W3r4 = 3 4 P 3 ×P 5 = 3 20 U 23 ⎯ 20 U 1.15 U 3 1⎯ 20 P 2 ÷3+P 5 ÷5= * 2 r z 3 + *5rz5= Q 2 ⎯ 2 v 45 = 0.707106781 U J01 2 @ ^ 0.5 = 2 ⎯ J 3 2.094395102 U ud 3(5+2)= 21. ②3×5+2= 3k5+2= 17. ③ (5 + 3) × 2 = ( 5 + 3) k 2 = @u 3 π cos ⎯ [rad] = 4 J02 @y1= 10. 5@c2= 500 × 25% = 500 k 25 @ a 120 ÷ 400 = ?% 120 z 400 @ a 500 + (500 × 25%) = 500 + 25 @ a 400 − (400 × 30%) = 400 & 30 @ a 125. 30. 625. 280. |5 − 9| = @W5&9= 4. o @W(5&9 )= 4. • • • • • • • • • • • • • @>t( 5 z 7 ) = 0.895879734 RAD ln 20 = i 20 = 2.995732274 log 50 = l 50 = 1.698970004 log2 16384 = @ O 2 r 16384 = @ O 2 H 16384 ) = e3 = @"3= 1÷e= 1z;V = 1 7 14. GRAD 14. 0.367879441 −100 ≤ θ ≤ 100 0 ≤ θ ≤ 200 13 ⎯ 42 0.309523809 8mS2r &3m4r k5A= 33'333.33333 o ¥26,510 = $? 26510 z t Y = 241. U 33m20 $2,750 = ¥? 2750 k t Y = r = 3 cm (r ⇒ Y) 3xY πr 2 = ? s;Y A=U 24 2 ⎯ 2⎯ 4 + 6 = 5 …(A) 302'500. 3. 28.27433388 24 z ( 4 + 6 )= 3 k ; < + 60 z;<= sinh−1 ⇒ D1 xI@>v sinh−1 0.5 = I 0.5 = 0.481211825 6 + 4 = ANS j6+4= 10. ANS + 5 = +5= 15. 8 × 2 = ANS 8k2= 16. ANS2 = A= 44 + 37 = ANS 44 + 37 = 1 5 32 ⎯ 256. 81. 9. *= j3@k1d2r +W4d3= 5 6 4⎯ 29 ⎯ 6 → [g] sin−1 0.8 @] 90. @] → [°] = [°] - 63 ⎯ 64 129599 ⎯ 64 -2'024.984375 8mS2& 3m4k5 A= → [°] 8 -2024 @ w 0.8 = 53.13010235 53.13010235 @] ;txmM<IJK L 8×2⇒M j8k2xM 24 ÷ (8 × 2) = 24 z ; M = (8 × 2) × 5 = ;Mk5= 16. 1 1⎯ 2 80. -2'024.984375 U -2024m63m64 U -129599m64 4.833333333 3W1W2+4W3= 4m5m6* 29m6 4.833333333 10 3 = @Y2W3= ( ⎯75 ) 7W5rm5= 5 = o 4.641588834 16807 ⎯ 3125 @q1W8= 1 ⎯ 2 * 64 W 225 = 8 ⎯ 15 2 ⎯4 = 3 2@1W3m4= 8 ⎯ 81 o 2@1W(3m4) = 1 64 ⎯ = 225 3 BIN 11001 110101100 @ h 1AC BIN @z BIN PEN @r PEN 3203 OCT @g OCT 654 DEC @/ (1010 − 100) × 11 = @z( 1010 & 100) k 11 = [BIN] BIN (111) → NEG d 111 = HEX (1FF) + OCT (512) = HEX (?) 2FEC − 2C9E ⇒ M1 +) 2000 − 1901 ⇒ M2 — M= 428. 10010 BIN BIN 1111111001 @ h 1FF @g+ 512 = OCT 1511 @h HEX 349 jxM @ h 2FEC & 2C9E m HEX 34E 2000 &1901 m HEX 6FF tM jxM A4D HEX 1011 AND 101 = @ z 1011 4 101 = [BIN] BIN 1 5A OR C3 = [HEX] @ h 5A p C3 = HEX NOT 10110 = [BIN] @zn 10110 = BIN 1111101001 24 XOR 4 = [OCT] @ g 24 x4= OCT B3 XNOR 2D = [HEX] @ h B3 C 2D = HEX FFFFFFFF61 → DEC @/ 12 DB 20 -159. [: [10] j 7 [ 31 [ 49.44 @ : 7°31’49.44” 123.678 [60] 12 ⎯ 23 1.2 W 2.3 = 1°2’3” ⎯= 2 1[2[3W2= 0(31 q1.5" 1 × 10 ⎯ = 2 × 103 1`3W2`3= 1 ⎯ 2 7⇒A j7xA 7. 4 ⎯= A 4W;A= 4 ⎯ 7 123.678 @ : 663 1250 7⎯ 123(40q40.8" 3h 30m 45s + 6h 45m 36s = [60] 3 [ 30 [ 45 + 6 [ 45 [ 36 = 1234°56’12” + 0°0’34.567” = [60] 1234 [ 56 [ 12 + 0 [ 0 [ 34.567 = 1234(56 q47." 3h 45m – 1.69h = [60] 3 [ 45 & 1.69 =@: 8m81 1.2 ⎯= 2.3 3 j@/ 25 @ z 16807m3125 7W5m5= ⎯= 8 3 BIN HEX (1AC) Wk 1 4 3⎯ + ⎯ = 2 3 zrgh/dn4 pxC DEC (25) 9 2 100. 11 2 5 3 × (A) + 60 ÷ (A) = ⎯ 1 J ⎯ 2 5 * 4m5m6 = 4 ⎯ 6 2⎯ U j 90 @ ] 1.65 1m13m20 o ] 1.25 + 2 W 5 = U U 7 o 110. 0 ≤ θ ≤ 180 0≤θ≤π 1.65 110 x Y θ = cos−1 x π ≤θ≤⎯ π −⎯ 2 2 U $1 = ¥110 (110 ⇒ Y) U 90° → [rad] 20.08553692 U 8−2 − 34 × 52 = 35. U 5 tanh−1 ⎯ = 33 ⎯ 20 665. • −90 ≤ θ ≤ 90 U tM 10 θ = sin−1 x, θ = tan−1 x 13 20 1⎯ 250. tMk5@a @M ANS = 59.03344706 33.33b03 sin 62°12’24” = [10] v 62 [ 12 [ 24 = 13 10(16 q21." 2(3q36." 0.884635235 uEH ( ( rθ == [°] ( rθ == 1436 [°] ( xy == x=6 y=4 j6H4 @u r: {: 7.211102551 33.69006753 14 H 36 @E X: Y: 11.32623792 8.228993532 33'333.33333 J13 nJ S#a# 2 [QUAD] b12 18 0. x y 12 41 5 ⎯ 9 12 H 41 _ DATA SET= 1. 8 13 8 H 13 _ DATA SET= 2. 0.6 5 2 5H2_ DATA SET= 3. 1 k9=* 5.0 23 200 23 H 200 _ DATA SET= 4. 5z9= 5 ⎯ 9 15 71 15 H 71 _ DATA SET= 5. [FIX, TAB = 1] j J 1 0 1 0.0 5z9= U U 0.6 a= ta a= 5.357506761 3 ⎯ 5 b= tb b= -3.120289663 2 5 c= @n 5⎯ k 9 = *2 5.4 UU 5.4 J13 5 *1 ⎯ × 9 = 5.5555555555555 × 10−1 × 9 9 3 2 ⎯ * × 9 = 0.6 × 9 5 x = 10 y = 22 16 tS b 1 0 S#a# 0 [SD] @Z y´ = ? 10 @ U 10 y´ x´ = ? 22 @ V 22 x´ 1: 2: DATA 20 0. 40 DATA SET= 1. 40 80 80 _ DATA SET= 2. 50 80 75 75 75 50 _ DATA SET= 3. DATA SET= 5. 45 – x = 75.71428571 45 σx = tp σx = 12.37179148 45 n= Σx = tg Σx= Σx2 = to tv sx= 7. 530. 41'200. S#a# 1 [LINE] 0. y 2 5 2H5_ DATA SET= 1. 2 5 _ DATA SET= 2. 12 24 12 H 24 _ DATA SET= 3. 21 21 21 40 40 40 21 H 40 H 3 _ DATA SET= 4. 15 25 15 H 25 _ DATA SET= 5. a= ta a= 1.050261097 b= tb b= 1.826044386 r= tf r= 0.995176343 sx = tv sx = 8.541216597 sy = tG sy = 15.67223812 6.528394256 x=3 y´ = ? 3 @ U 3 y´ y = 46 x´ = ? 46 @ V 46 x´ 24.61590706 F: ■ 3_ X: d 60 _ 17 –x = Σ ⎯x σx = n x 2 − nx– 2 Σ⎯ n−1 sx = n 64.43210706 DATA SET= d d d 45 _ X: Σy – y= ⎯ ( 95 & ;R) ⎯ × 10 + 50 = z ; v sx k 10 + 50 = (95 − – x) DATA SET= d@# 60 13.3630621 sx2 = 178.5714286 A= DATA SET= 50 _ 4. tR DATA SET= 40 H 2 _ 75 H 3 _ DATA SET= – x = DATA SET= 30 _ DATA 30 tc 9.63201409 -3.432772026 S#a# 0 [SD] 20 _ 30 95 _ n= 24.4880159 _Hud# DATA 95 50 _ 0.503334057 c= b10 _HRvpcgoQ GsijhfabS VU x 720. @] [ENG: TAB 2] J 1 2 2 b11 24. → [g] 3.3b04 sx2 = 3. 6@Z+7 @Z= [SCI: SIG 2] J 1 1 2 DATA 50. U sx = @ q 27 = • U Σx2 = 4. 10 @ e 3 = = DEG DATA 15 = (cosh 1.5 + sinh 1.5)2 = j ( H $ 1.5 + H v 1.5 ) A = 20.08553692 7 * 49 & 4 @ D 81 = 4@B= 10P3 5C2 – M= 1 6 33'333.33 [NORM1] 4! = 4. ⎯+⎯= [FIX: TAB 2] J 1 0 2 ANS × 9 = 27 = 3p * 49 r & 4 @ D 81 = 2 1.25 + ⎯ = 1.25 + 2 W 5 = 5 450. 150 k 3 m +) $250: M1 + 250 ⇒ M2 250 m −) M2 × 5% 21. 17. j 100000 z 3 = o J00 J [MDF] 0.707106781 U tan−11 [g] = Q 2 ⎯ 2 p 49 − 4p 81 = $150 × 3 ⇒ M1 512. 0.927295218 ③ ANS × 9 = 0.866025403 8@1= @] 16. 5 ÷ 9 = ANS ⎯ 2 J01 $sW4= o 100000 ÷ 3 = 14 Q 3 83 = 6.447419591 → [rad] d [NORM1] 0. ( 12 m 3 ) m 1 W 4 = 6.447419591 @ Y 1.7 = 50.11872336 17. [NORM1] 2'720. o 0. jxM 0⇒M 101.7 = d u 1'700. ( 12 m 3 r)m 1W4= 16. ② ② 102. U o ① 3(5 + 2) = 91. j v 60 = 0. @Z ① sin 60 [°] = 3Q 5+5Q 2 ⎯ 15 0.918618116 U 2 1'250'000. @P0 H 15 3.872983346 U 2cos−1 0.5 [rad] = -90 40 = 1⎯ *3rk*5 = sin 45 = 3 7 3⎯ v$tw^ysH> ilO" VYZA1 *mDqBecaW H 6 U ⎯+⎯= 140. 5 68 × 40 = 1 0.003 j 3 z 1000 = [NORM1] (123) ⎯ 4 = sy = –2 Σ y 2 − ny ⎯ n−1 x 2 − nx– 2 Σ⎯ n Σx = x1 + x2 + … + xn Σx2 = x1 2 + x2 2 + … + xn2 Σy − 2 ny– 2 ⎯ n Σxy = x1 y1 + x2 y2 + … + xn yn Σy = y1 + y2 + … + yn Σy 2 = y1 2 + y2 2 + … + yn2 σy = Function keys Display Buffer space* Funktionstasten Anzeige Pufferplatz* Touches de fonction Affichage Espace tampon* Visualizador Espacio de memoria intermedia* Teclas de función Exibição Espaço na memória intermediária* Teclas de função Memoria tampone* Display Tasti di funzione Bufferruimte* Display Functietoetsen Pufferterület* Kijelző Függvénybillentyűk Vyrovnávací paměť* Zobrazení Tlačítka funkcí Buffertutrymme* Visning Funktionstangenter Puskuritila* Näyttö Funktionäppäimet Bufferplads* Display Funktionstaster * Tombol fungsi Function Funktion Fonction Función Função Funzioni Functie Függvény Funkce Funktion Funktio Funktion Dynamic range zulässiger Bereich Plage dynamique Rango dinámico Gama dinâmica Campi dinamici Rekencapaciteit Megengedett számítási tartomány Dynamický rozsah Definitionsområde Dynaaminen ala Dynamikområde Fungsi Kisaran dinamis Tampilan Ruang buffer* @Z □−1 1 A □2 1 @1 □3 1 m □□ 5 @O log□(□) 7 @" e□ 5 sin–1 x, cos–1 x |x| ≤ 1 5 tan x, P x | x | < 10100 ln x, log x, loga x 10–99 ≤ x < 10100, 10–99 ≤ a < 10100 (a ≠ 1) 10□ @Y 0. * P □ 5 1. @q 3P □ 5 □P 7 sin x, cos x, tan x DEG: | x | < 1010 (tan x : | x | ≠ 90(2n − 1))* π ⎯ RAD: | x | < 180 × 1010 π (tan x: | x | ≠ ⎯ (2n − 1))* 2 10 10 GRAD: | x | < ⎯ 9 × 10 (tan x: | x | ≠ 100(2n − 1))* –1 3 • y > 0: −10100 < x log y < 100 • y = 0: 0 < x < 10100 2. @D 3. W/@k □ ⎯ □ 7 (0 < | x | < 1: ⎯ x = 2n − 1, x ≠ 0)*, @W |□| 5 −10100 < x log | y | < 100 () ( 4 4. 3. 45. 3. 60. NOT BIN: 1000000000 ≤ x ≤ 1111111111 0 ≤ x ≤ 111111111 PEN: 2222222223 ≤ x ≤ 4444444444 0 ≤ x ≤ 2222222221 OCT: 4000000000 ≤ x ≤ 7777777777 0 ≤ x ≤ 3777777777 HEX: FDABF41C01 ≤ x ≤ FFFFFFFFFF 0 ≤ x ≤ 2540BE3FE NEG BIN: 1000000001 ≤ x ≤ 1111111111 0 ≤ x ≤ 111111111 PEN: 2222222223 ≤ x ≤ 4444444444 0 ≤ x ≤ 2222222222 OCT: 4000000001 ≤ x ≤ 7777777777 0 ≤ x ≤ 3777777777 HEX: FDABF41C01 ≤ x ≤ FFFFFFFFFF 0 ≤ x ≤ 2540BE3FF 19 □ ) * The amount of memory used for the sake of display in the WriteView editor, measured in characters (excluding entered values, denoted in the chart by “□”). * Der für die Anzeige in WriteView Editor verwendete Speicherplatz, gemessen in Zeichen (ohne die eingegebenen Werte, die in der Tabelle mit „□“ markiert sind). * Espace mémoire utilisé pour préserver l’affichage dans l’éditeur WriteView, mesuré en caractère (à l’exception des valeurs d’entrée, indiquées dans le tableau par “□”). * La cantidad de memoria usada para visualizar en el editor Write View, medida en caracteres (excluyendo los valores introducidos, indicados en el grafico mediante “□”). * A quantidade de memória que é usada para a exibição no editor WriteView, medida em caracteres (excluindo os valores introduzidos, indicados no quadro por “□”). * La quantità di memoria utilizzata per la visualizzazione nell’editor WriteView, misurata in caratteri (escludendo i valori inseriti, indicati nella tabella con il simbolo “□”). * De hoeveelheid geheugen dat wordt gebruikt om de WriteView editor weer te geven, gemeten in symbolen (met uitzondering van ingevoerde waarden aangeduid in de grafiek met “□”). * A WriteView szerkesztő megjelenítési műveleteire használatos memóriaterület, karakterben kifejezve (az ábrán „□” karakterrel jelölt beviteli értékeket nem számítva). * Množství paměti využívané pro účely zobrazení v editoru WriteView, vyjádřené počtem znaků (vyjma zadaných hodnot, označených v grafu znakem „□“). * Den mängd minne som används för visning med WriteViewredigeraren, mätt i antalet tecken (exklusive inmatade värden, vilka anges som ”□” i tabellen). * Näytön WriteView-editorissa käyttämä muisti merkkeinä laskettuna (pois lukien syötetyt arvot, taulukossa merkitty ”□”). * Den mængde hukommelse, der bruges til visning i WriteVieweditoren, målt i tegn (med undtagelse af indtastede værdier, der angives med „□“ i tabellen). x=n 1 1 −10100 < ⎯ x log y < 100 (x ≠ 0) • y = 0: 0 < x < 10100 • y < 0: x = 2n − 1 1 (0 < | x | < 1: ⎯ x = n, x ≠ 0)*, • y > 0: x y P 1 −10100 < ⎯ x log | y | < 100 ex −10100 < x ≤ 230.2585092 10 x −10100 < x < 100 sinh x, cosh x, tanh x | x | ≤ 230.2585092 sinh x | x | < 1050 cosh–1 x 1 ≤ x < 1050 –1 |x| < 1 x2 | x | < 1050 x3 | x | < 2.15443469 × 1033 x P 0 ≤ x < 10100 x –1 | x | < 10100 (x ≠ 0) n! 0 ≤ n ≤ 69* 0 ≤ r ≤ n ≤ 9999999999* n! ⎯ (n − r)! nPr Umweltschutz Das Gerät wird durch eine Batterie mit Strom versorgt. Um die Batterie sicher und umweltschonend zu entsorgen, beachten Sie bitte folgende Punkte: • Bringen Sie die leere Batterie zu Ihrer örtlichen Mülldeponie, zum Händler oder zum KundenserviceZentrum zur Wiederverwertung. • Werfen Sie die leere Batterie niemals ins Feuer, ins Wasser oder in den Hausmüll. Seulement pour la France/For France only: Protection de l’environnement L’appareil est alimenté par pile. Afin de protéger l’environnement, nous vous recommandons: • d’apporter la pile usagée ou à votre revendeur ou au service après-vente, pour recyclage. • de ne pas jeter la pile usagée dans une source de chaleur, dans l’eau ou dans un vide-ordures. Endast svensk version/For Sweden only: Miljöskydd Denna produkt drivs av batteri. Vid batteribyte skall följande iakttagas: • Det förbrukade batteriet skall inlämnas till batteriinsamling eller till kommunal miljöstation för återinssamling. • Kasta ej batteriet i vattnet eller i hushållssoporna. Batteriet får ej heller utsättas för öppen eld. OPMERKING: ALLEEN VOOR NEDERLAND/ NOTE: FOR NETHERLANDS ONLY 100 0 ≤ r ≤ n ≤ 9999999999* 0 ≤ r ≤ 69 nCr n! ⎯ (n − r)! ↕DEG, D°M’S r, θ < 10 Nur für Deutschland/For Germany only: For Europe only: tanh x –1 x, y * Jumlah memori yang digunakan untuk kepentingan tampilan dalam editor WriteView, diukur dalam jumlah karakter (tidak termasuk nilai yang dimasukkan, ditunjukkan dalam diagram dengan “□”) • y < 0: yx * n, r: integer / ganze Zahlen / entier / entero / inteiro / intero / geheel getal / egész számok / celé číslo / heltal / kokonaisluku / heltal / / / bilangan bulat r, θ x, y < 10100 0°0’0.00001” ≤ | x | < 10000° x 2 + y 2 < 10100 0 ≤ r < 10100 DEG: | θ | < 1010 π ⎯ RAD: | θ | < 180 × 1010 10 10 GRAD: | θ | < ⎯ 9 × 10 DEG DRG▶ DEC BIN PEN OCT HEX AND OR XOR XNOR RAD RAD, GRAD DEG: | x | < 10100 π GRAD: | x | < ⎯ 1098 2 × DEC: | x | ≤ 9999999999 BIN: 1000000000 ≤ x ≤ 1111111111 0 ≤ x ≤ 111111111 PEN: 2222222223 ≤ x ≤ 4444444444 0 ≤ x ≤ 2222222222 OCT: 4000000000 ≤ x ≤ 7777777777 0 ≤ x ≤ 3777777777 HEX: FDABF41C01 ≤ x ≤ FFFFFFFFFF 0 ≤ x ≤ 2540BE3FF A. Information on Disposal for Users (private households) 1. In the European Union Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin! Used electrical and electronic equipment must be treated separately and in accordance Attention: Your product with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment. is marked with this Following the implementation by member states, private households within the EU states symbol. It means that may return their used electrical and electronic equipment to designated collection facilities used electrical and free of charge*. In some countries* your local retailer may also take back your old product electronic products free of charge if you purchase a similar new one. should not be mixed with general household *) Please contact your local authority for further details. waste. There is a If your used electrical or electronic equipment has batteries or accumulators, please separate collection dispose of these separately beforehand according to local requirements. system for these By disposing of this product correctly you will help ensure that the waste undergoes the products. necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due to inappropriate waste handling. 2. In other Countries outside the EU If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal. For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch. ENGLISH B. Information on Disposal for Business Users. 1. In the European Union If the product is used for business purposes and you want to discard it: Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection facilities. For Spain: Please contact the established collection system or your local authority for take-back of your used products. 2. In other Countries outside the EU If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal. For Australia/New Zealand only: For warranty information please see www.sharp.net.au. o 3 ÷ 1000 = ENGLISH 1 EL-W531 EL-W531G EL-W531H EL-W531HA EL-W535 CALCULATION EXAMPLES ANWENDUNGSBEISPIELE EXEMPLES DE CALCUL EJEMPLOS DE CÁLCULO EXEMPLOS DE CÁLCULO ESEMPI DI CALCOLO REKENVOORBEELDEN PÉLDASZÁMÍTÁSOK PŘÍKLADY VÝPOČTŮ RÄKNEEXEMPEL LASKENTAESIMERKKEJÄ UDREGNINGSEKSEMPLER [NORM2] J14 3.b-03 [NORM1] J13 0.003 +&kz()S` 4 45 + 285 ÷ 3 = j 45 + 285 z 3 = 18 + 6 ⎯= 15 − 8 ( 18 + 6 ) z (15 & 8 = 42 × −5 + 120 = 42 k S 5 + 120 = (5 × 103) ÷ (4 × 10−3) = 5 ` 3 z 4 `S3= CONTOH-CONTOH PERHITUNGAN 34 + 57 = 34 + 57 = 45 + 57 = 45 = 68 × 25 = 68 k 25 = 2 5 j2W5r +W3r4 = 3 4 P 3 ×P 5 = 3 20 U 23 ⎯ 20 U 1.15 U 3 1⎯ 20 P 2 ÷3+P 5 ÷5= * 2 r z 3 + *5rz5= Q 2 ⎯ 2 v 45 = 0.707106781 U J01 2 @ ^ 0.5 = 2 ⎯ J 3 2.094395102 U ud 3(5+2)= 21. ②3×5+2= 3k5+2= 17. ③ (5 + 3) × 2 = ( 5 + 3) k 2 = @u 3 π cos ⎯ [rad] = 4 J02 @y1= 10. 5@c2= 500 × 25% = 500 k 25 @ a 120 ÷ 400 = ?% 120 z 400 @ a 500 + (500 × 25%) = 500 + 25 @ a 400 − (400 × 30%) = 400 & 30 @ a 125. 30. 625. 280. |5 − 9| = @W5&9= 4. o @W(5&9 )= 4. • • • • • • • • • • • • • @>t( 5 z 7 ) = 0.895879734 RAD ln 20 = i 20 = 2.995732274 log 50 = l 50 = 1.698970004 log2 16384 = @ O 2 r 16384 = @ O 2 H 16384 ) = e3 = @"3= 1÷e= 1z;V = 1 7 14. GRAD 14. 0.367879441 −100 ≤ θ ≤ 100 0 ≤ θ ≤ 200 13 ⎯ 42 0.309523809 8mS2r &3m4r k5A= 33'333.33333 o ¥26,510 = $? 26510 z t Y = 241. U 33m20 $2,750 = ¥? 2750 k t Y = r = 3 cm (r ⇒ Y) 3xY πr 2 = ? s;Y A=U 24 2 ⎯ 2⎯ 4 + 6 = 5 …(A) 302'500. 3. 28.27433388 24 z ( 4 + 6 )= 3 k ; < + 60 z;<= sinh−1 ⇒ D1 xI@>v sinh−1 0.5 = I 0.5 = 0.481211825 6 + 4 = ANS j6+4= 10. ANS + 5 = +5= 15. 8 × 2 = ANS 8k2= 16. ANS2 = A= 44 + 37 = ANS 44 + 37 = 1 5 32 ⎯ 256. 81. 9. *= j3@k1d2r +W4d3= 5 6 4⎯ 29 ⎯ 6 → [g] sin−1 0.8 @] 90. @] → [°] = [°] - 63 ⎯ 64 129599 ⎯ 64 -2'024.984375 8mS2& 3m4k5 A= → [°] 8 -2024 @ w 0.8 = 53.13010235 53.13010235 @] ;txmM<IJK L 8×2⇒M j8k2xM 24 ÷ (8 × 2) = 24 z ; M = (8 × 2) × 5 = ;Mk5= 16. 1 1⎯ 2 80. -2'024.984375 U -2024m63m64 U -129599m64 4.833333333 3W1W2+4W3= 4m5m6* 29m6 4.833333333 10 3 = @Y2W3= ( ⎯75 ) 7W5rm5= 5 = o 4.641588834 16807 ⎯ 3125 @q1W8= 1 ⎯ 2 * 64 W 225 = 8 ⎯ 15 2 ⎯4 = 3 2@1W3m4= 8 ⎯ 81 o 2@1W(3m4) = 1 64 ⎯ = 225 3 BIN 11001 110101100 @ h 1AC BIN @z BIN PEN @r PEN 3203 OCT @g OCT 654 DEC @/ (1010 − 100) × 11 = @z( 1010 & 100) k 11 = [BIN] BIN (111) → NEG d 111 = HEX (1FF) + OCT (512) = HEX (?) 2FEC − 2C9E ⇒ M1 +) 2000 − 1901 ⇒ M2 — M= 428. 10010 BIN BIN 1111111001 @ h 1FF @g+ 512 = OCT 1511 @h HEX 349 jxM @ h 2FEC & 2C9E m HEX 34E 2000 &1901 m HEX 6FF tM jxM A4D HEX 1011 AND 101 = @ z 1011 4 101 = [BIN] BIN 1 5A OR C3 = [HEX] @ h 5A p C3 = HEX NOT 10110 = [BIN] @zn 10110 = BIN 1111101001 24 XOR 4 = [OCT] @ g 24 x4= OCT B3 XNOR 2D = [HEX] @ h B3 C 2D = HEX FFFFFFFF61 → DEC @/ 12 DB 20 -159. [: [10] j 7 [ 31 [ 49.44 @ : 7°31’49.44” 123.678 [60] 12 ⎯ 23 1.2 W 2.3 = 1°2’3” ⎯= 2 1[2[3W2= 0(31 q1.5" 1 × 10 ⎯ = 2 × 103 1`3W2`3= 1 ⎯ 2 7⇒A j7xA 7. 4 ⎯= A 4W;A= 4 ⎯ 7 123.678 @ : 663 1250 7⎯ 123(40q40.8" 3h 30m 45s + 6h 45m 36s = [60] 3 [ 30 [ 45 + 6 [ 45 [ 36 = 1234°56’12” + 0°0’34.567” = [60] 1234 [ 56 [ 12 + 0 [ 0 [ 34.567 = 1234(56 q47." 3h 45m – 1.69h = [60] 3 [ 45 & 1.69 =@: 8m81 1.2 ⎯= 2.3 3 j@/ 25 @ z 16807m3125 7W5m5= ⎯= 8 3 BIN HEX (1AC) Wk 1 4 3⎯ + ⎯ = 2 3 zrgh/dn4 pxC DEC (25) 9 2 100. 11 2 5 3 × (A) + 60 ÷ (A) = ⎯ 1 J ⎯ 2 5 * 4m5m6 = 4 ⎯ 6 2⎯ U j 90 @ ] 1.65 1m13m20 o ] 1.25 + 2 W 5 = U U 7 o 110. 0 ≤ θ ≤ 180 0≤θ≤π 1.65 110 x Y θ = cos−1 x π ≤θ≤⎯ π −⎯ 2 2 U $1 = ¥110 (110 ⇒ Y) U 90° → [rad] 20.08553692 U 8−2 − 34 × 52 = 35. U 5 tanh−1 ⎯ = 33 ⎯ 20 665. • −90 ≤ θ ≤ 90 U tM 10 θ = sin−1 x, θ = tan−1 x 13 20 1⎯ 250. tMk5@a @M ANS = 59.03344706 33.33b03 sin 62°12’24” = [10] v 62 [ 12 [ 24 = 13 10(16 q21." 2(3q36." 0.884635235 uEH ( ( rθ == [°] ( rθ == 1436 [°] ( xy == x=6 y=4 j6H4 @u r: {: 7.211102551 33.69006753 14 H 36 @E X: Y: 11.32623792 8.228993532 33'333.33333 J13 nJ S#a# 2 [QUAD] b12 18 0. x y 12 41 5 ⎯ 9 12 H 41 _ DATA SET= 1. 8 13 8 H 13 _ DATA SET= 2. 0.6 5 2 5H2_ DATA SET= 3. 1 k9=* 5.0 23 200 23 H 200 _ DATA SET= 4. 5z9= 5 ⎯ 9 15 71 15 H 71 _ DATA SET= 5. [FIX, TAB = 1] j J 1 0 1 0.0 5z9= U U 0.6 a= ta a= 5.357506761 3 ⎯ 5 b= tb b= -3.120289663 2 5 c= @n 5⎯ k 9 = *2 5.4 UU 5.4 J13 5 *1 ⎯ × 9 = 5.5555555555555 × 10−1 × 9 9 3 2 ⎯ * × 9 = 0.6 × 9 5 x = 10 y = 22 16 tS b 1 0 S#a# 0 [SD] @Z y´ = ? 10 @ U 10 y´ x´ = ? 22 @ V 22 x´ 1: 2: DATA 20 0. 40 DATA SET= 1. 40 80 80 _ DATA SET= 2. 50 80 75 75 75 50 _ DATA SET= 3. DATA SET= 5. 45 – x = 75.71428571 45 σx = tp σx = 12.37179148 45 n= Σx = tg Σx= Σx2 = to tv sx= 7. 530. 41'200. S#a# 1 [LINE] 0. y 2 5 2H5_ DATA SET= 1. 2 5 _ DATA SET= 2. 12 24 12 H 24 _ DATA SET= 3. 21 21 21 40 40 40 21 H 40 H 3 _ DATA SET= 4. 15 25 15 H 25 _ DATA SET= 5. a= ta a= 1.050261097 b= tb b= 1.826044386 r= tf r= 0.995176343 sx = tv sx = 8.541216597 sy = tG sy = 15.67223812 6.528394256 x=3 y´ = ? 3 @ U 3 y´ y = 46 x´ = ? 46 @ V 46 x´ 24.61590706 F: ■ 3_ X: d 60 _ 17 –x = Σ ⎯x σx = n x 2 − nx– 2 Σ⎯ n−1 sx = n 64.43210706 DATA SET= d d d 45 _ X: Σy – y= ⎯ ( 95 & ;R) ⎯ × 10 + 50 = z ; v sx k 10 + 50 = (95 − – x) DATA SET= d@# 60 13.3630621 sx2 = 178.5714286 A= DATA SET= 50 _ 4. tR DATA SET= 40 H 2 _ 75 H 3 _ DATA SET= – x = DATA SET= 30 _ DATA 30 tc 9.63201409 -3.432772026 S#a# 0 [SD] 20 _ 30 95 _ n= 24.4880159 _Hud# DATA 95 50 _ 0.503334057 c= b10 _HRvpcgoQ GsijhfabS VU x 720. @] [ENG: TAB 2] J 1 2 2 b11 24. → [g] 3.3b04 sx2 = 3. 6@Z+7 @Z= [SCI: SIG 2] J 1 1 2 DATA 50. U sx = @ q 27 = • U Σx2 = 4. 10 @ e 3 = = DEG DATA 15 = (cosh 1.5 + sinh 1.5)2 = j ( H $ 1.5 + H v 1.5 ) A = 20.08553692 7 * 49 & 4 @ D 81 = 4@B= 10P3 5C2 – M= 1 6 33'333.33 [NORM1] 4! = 4. ⎯+⎯= [FIX: TAB 2] J 1 0 2 ANS × 9 = 27 = 3p * 49 r & 4 @ D 81 = 2 1.25 + ⎯ = 1.25 + 2 W 5 = 5 450. 150 k 3 m +) $250: M1 + 250 ⇒ M2 250 m −) M2 × 5% 21. 17. j 100000 z 3 = o J00 J [MDF] 0.707106781 U tan−11 [g] = Q 2 ⎯ 2 p 49 − 4p 81 = $150 × 3 ⇒ M1 512. 0.927295218 ③ ANS × 9 = 0.866025403 8@1= @] 16. 5 ÷ 9 = ANS ⎯ 2 J01 $sW4= o 100000 ÷ 3 = 14 Q 3 83 = 6.447419591 → [rad] d [NORM1] 0. ( 12 m 3 ) m 1 W 4 = 6.447419591 @ Y 1.7 = 50.11872336 17. [NORM1] 2'720. o 0. jxM 0⇒M 101.7 = d u 1'700. ( 12 m 3 r)m 1W4= 16. ② ② 102. U o ① 3(5 + 2) = 91. j v 60 = 0. @Z ① sin 60 [°] = 3Q 5+5Q 2 ⎯ 15 0.918618116 U 2 1'250'000. @P0 H 15 3.872983346 U 2cos−1 0.5 [rad] = -90 40 = 1⎯ *3rk*5 = sin 45 = 3 7 3⎯ v$tw^ysH> ilO" VYZA1 *mDqBecaW H 6 U ⎯+⎯= 140. 5 68 × 40 = 1 0.003 j 3 z 1000 = [NORM1] (123) ⎯ 4 = sy = –2 Σ y 2 − ny ⎯ n−1 x 2 − nx– 2 Σ⎯ n Σx = x1 + x2 + … + xn Σx2 = x1 2 + x2 2 + … + xn2 Σy − 2 ny– 2 ⎯ n Σxy = x1 y1 + x2 y2 + … + xn yn Σy = y1 + y2 + … + yn Σy 2 = y1 2 + y2 2 + … + yn2 σy = Function keys Display Buffer space* Funktionstasten Anzeige Pufferplatz* Touches de fonction Affichage Espace tampon* Visualizador Espacio de memoria intermedia* Teclas de función Exibição Espaço na memória intermediária* Teclas de função Memoria tampone* Display Tasti di funzione Bufferruimte* Display Functietoetsen Pufferterület* Kijelző Függvénybillentyűk Vyrovnávací paměť* Zobrazení Tlačítka funkcí Buffertutrymme* Visning Funktionstangenter Puskuritila* Näyttö Funktionäppäimet Bufferplads* Display Funktionstaster * Tombol fungsi Function Funktion Fonction Función Função Funzioni Functie Függvény Funkce Funktion Funktio Funktion Dynamic range zulässiger Bereich Plage dynamique Rango dinámico Gama dinâmica Campi dinamici Rekencapaciteit Megengedett számítási tartomány Dynamický rozsah Definitionsområde Dynaaminen ala Dynamikområde Fungsi Kisaran dinamis Tampilan Ruang buffer* @Z □−1 1 A □2 1 @1 □3 1 m □□ 5 @O log□(□) 7 @" e□ 5 sin–1 x, cos–1 x |x| ≤ 1 5 tan x, P x | x | < 10100 ln x, log x, loga x 10–99 ≤ x < 10100, 10–99 ≤ a < 10100 (a ≠ 1) 10□ @Y 0. * P □ 5 1. @q 3P □ 5 □P 7 sin x, cos x, tan x DEG: | x | < 1010 (tan x : | x | ≠ 90(2n − 1))* π ⎯ RAD: | x | < 180 × 1010 π (tan x: | x | ≠ ⎯ (2n − 1))* 2 10 10 GRAD: | x | < ⎯ 9 × 10 (tan x: | x | ≠ 100(2n − 1))* –1 3 • y > 0: −10100 < x log y < 100 • y = 0: 0 < x < 10100 2. @D 3. W/@k □ ⎯ □ 7 (0 < | x | < 1: ⎯ x = 2n − 1, x ≠ 0)*, @W |□| 5 −10100 < x log | y | < 100 () ( 4 4. 3. 45. 3. 60. NOT BIN: 1000000000 ≤ x ≤ 1111111111 0 ≤ x ≤ 111111111 PEN: 2222222223 ≤ x ≤ 4444444444 0 ≤ x ≤ 2222222221 OCT: 4000000000 ≤ x ≤ 7777777777 0 ≤ x ≤ 3777777777 HEX: FDABF41C01 ≤ x ≤ FFFFFFFFFF 0 ≤ x ≤ 2540BE3FE NEG BIN: 1000000001 ≤ x ≤ 1111111111 0 ≤ x ≤ 111111111 PEN: 2222222223 ≤ x ≤ 4444444444 0 ≤ x ≤ 2222222222 OCT: 4000000001 ≤ x ≤ 7777777777 0 ≤ x ≤ 3777777777 HEX: FDABF41C01 ≤ x ≤ FFFFFFFFFF 0 ≤ x ≤ 2540BE3FF 19 □ ) * The amount of memory used for the sake of display in the WriteView editor, measured in characters (excluding entered values, denoted in the chart by “□”). * Der für die Anzeige in WriteView Editor verwendete Speicherplatz, gemessen in Zeichen (ohne die eingegebenen Werte, die in der Tabelle mit „□“ markiert sind). * Espace mémoire utilisé pour préserver l’affichage dans l’éditeur WriteView, mesuré en caractère (à l’exception des valeurs d’entrée, indiquées dans le tableau par “□”). * La cantidad de memoria usada para visualizar en el editor Write View, medida en caracteres (excluyendo los valores introducidos, indicados en el grafico mediante “□”). * A quantidade de memória que é usada para a exibição no editor WriteView, medida em caracteres (excluindo os valores introduzidos, indicados no quadro por “□”). * La quantità di memoria utilizzata per la visualizzazione nell’editor WriteView, misurata in caratteri (escludendo i valori inseriti, indicati nella tabella con il simbolo “□”). * De hoeveelheid geheugen dat wordt gebruikt om de WriteView editor weer te geven, gemeten in symbolen (met uitzondering van ingevoerde waarden aangeduid in de grafiek met “□”). * A WriteView szerkesztő megjelenítési műveleteire használatos memóriaterület, karakterben kifejezve (az ábrán „□” karakterrel jelölt beviteli értékeket nem számítva). * Množství paměti využívané pro účely zobrazení v editoru WriteView, vyjádřené počtem znaků (vyjma zadaných hodnot, označených v grafu znakem „□“). * Den mängd minne som används för visning med WriteViewredigeraren, mätt i antalet tecken (exklusive inmatade värden, vilka anges som ”□” i tabellen). * Näytön WriteView-editorissa käyttämä muisti merkkeinä laskettuna (pois lukien syötetyt arvot, taulukossa merkitty ”□”). * Den mængde hukommelse, der bruges til visning i WriteVieweditoren, målt i tegn (med undtagelse af indtastede værdier, der angives med „□“ i tabellen). x=n 1 1 −10100 < ⎯ x log y < 100 (x ≠ 0) • y = 0: 0 < x < 10100 • y < 0: x = 2n − 1 1 (0 < | x | < 1: ⎯ x = n, x ≠ 0)*, • y > 0: x y P 1 −10100 < ⎯ x log | y | < 100 ex −10100 < x ≤ 230.2585092 10 x −10100 < x < 100 sinh x, cosh x, tanh x | x | ≤ 230.2585092 sinh x | x | < 1050 cosh–1 x 1 ≤ x < 1050 –1 |x| < 1 x2 | x | < 1050 x3 | x | < 2.15443469 × 1033 x P 0 ≤ x < 10100 x –1 | x | < 10100 (x ≠ 0) n! 0 ≤ n ≤ 69* 0 ≤ r ≤ n ≤ 9999999999* n! ⎯ (n − r)! nPr Umweltschutz Das Gerät wird durch eine Batterie mit Strom versorgt. Um die Batterie sicher und umweltschonend zu entsorgen, beachten Sie bitte folgende Punkte: • Bringen Sie die leere Batterie zu Ihrer örtlichen Mülldeponie, zum Händler oder zum KundenserviceZentrum zur Wiederverwertung. • Werfen Sie die leere Batterie niemals ins Feuer, ins Wasser oder in den Hausmüll. Seulement pour la France/For France only: Protection de l’environnement L’appareil est alimenté par pile. Afin de protéger l’environnement, nous vous recommandons: • d’apporter la pile usagée ou à votre revendeur ou au service après-vente, pour recyclage. • de ne pas jeter la pile usagée dans une source de chaleur, dans l’eau ou dans un vide-ordures. Endast svensk version/For Sweden only: Miljöskydd Denna produkt drivs av batteri. Vid batteribyte skall följande iakttagas: • Det förbrukade batteriet skall inlämnas till batteriinsamling eller till kommunal miljöstation för återinssamling. • Kasta ej batteriet i vattnet eller i hushållssoporna. Batteriet får ej heller utsättas för öppen eld. OPMERKING: ALLEEN VOOR NEDERLAND/ NOTE: FOR NETHERLANDS ONLY 100 0 ≤ r ≤ n ≤ 9999999999* 0 ≤ r ≤ 69 nCr n! ⎯ (n − r)! ↕DEG, D°M’S r, θ < 10 Nur für Deutschland/For Germany only: For Europe only: tanh x –1 x, y * Jumlah memori yang digunakan untuk kepentingan tampilan dalam editor WriteView, diukur dalam jumlah karakter (tidak termasuk nilai yang dimasukkan, ditunjukkan dalam diagram dengan “□”) • y < 0: yx * n, r: integer / ganze Zahlen / entier / entero / inteiro / intero / geheel getal / egész számok / celé číslo / heltal / kokonaisluku / heltal / / / bilangan bulat r, θ x, y < 10100 0°0’0.00001” ≤ | x | < 10000° x 2 + y 2 < 10100 0 ≤ r < 10100 DEG: | θ | < 1010 π ⎯ RAD: | θ | < 180 × 1010 10 10 GRAD: | θ | < ⎯ 9 × 10 DEG DRG▶ DEC BIN PEN OCT HEX AND OR XOR XNOR RAD RAD, GRAD DEG: | x | < 10100 π GRAD: | x | < ⎯ 1098 2 × DEC: | x | ≤ 9999999999 BIN: 1000000000 ≤ x ≤ 1111111111 0 ≤ x ≤ 111111111 PEN: 2222222223 ≤ x ≤ 4444444444 0 ≤ x ≤ 2222222222 OCT: 4000000000 ≤ x ≤ 7777777777 0 ≤ x ≤ 3777777777 HEX: FDABF41C01 ≤ x ≤ FFFFFFFFFF 0 ≤ x ≤ 2540BE3FF A. Information on Disposal for Users (private households) 1. In the European Union Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin! Used electrical and electronic equipment must be treated separately and in accordance Attention: Your product with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment. is marked with this Following the implementation by member states, private households within the EU states symbol. It means that may return their used electrical and electronic equipment to designated collection facilities used electrical and free of charge*. In some countries* your local retailer may also take back your old product electronic products free of charge if you purchase a similar new one. should not be mixed with general household *) Please contact your local authority for further details. waste. There is a If your used electrical or electronic equipment has batteries or accumulators, please separate collection dispose of these separately beforehand according to local requirements. system for these By disposing of this product correctly you will help ensure that the waste undergoes the products. necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due to inappropriate waste handling. 2. In other Countries outside the EU If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal. For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch. ENGLISH B. Information on Disposal for Business Users. 1. In the European Union If the product is used for business purposes and you want to discard it: Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection facilities. For Spain: Please contact the established collection system or your local authority for take-back of your used products. 2. In other Countries outside the EU If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal. For Australia/New Zealand only: For warranty information please see www.sharp.net.au. o 3 ÷ 1000 = ENGLISH 1 EL-W531 EL-W531G EL-W531H EL-W531HA EL-W535 CALCULATION EXAMPLES ANWENDUNGSBEISPIELE EXEMPLES DE CALCUL EJEMPLOS DE CÁLCULO EXEMPLOS DE CÁLCULO ESEMPI DI CALCOLO REKENVOORBEELDEN PÉLDASZÁMÍTÁSOK PŘÍKLADY VÝPOČTŮ RÄKNEEXEMPEL LASKENTAESIMERKKEJÄ UDREGNINGSEKSEMPLER [NORM2] J14 3.b-03 [NORM1] J13 0.003 +&kz()S` 4 45 + 285 ÷ 3 = j 45 + 285 z 3 = 18 + 6 ⎯= 15 − 8 ( 18 + 6 ) z (15 & 8 = 42 × −5 + 120 = 42 k S 5 + 120 = (5 × 103) ÷ (4 × 10−3) = 5 ` 3 z 4 `S3= CONTOH-CONTOH PERHITUNGAN 34 + 57 = 34 + 57 = 45 + 57 = 45 = 68 × 25 = 68 k 25 = 2 5 j2W5r +W3r4 = 3 4 P 3 ×P 5 = 3 20 U 23 ⎯ 20 U 1.15 U 3 1⎯ 20 P 2 ÷3+P 5 ÷5= * 2 r z 3 + *5rz5= Q 2 ⎯ 2 v 45 = 0.707106781 U J01 2 @ ^ 0.5 = 2 ⎯ J 3 2.094395102 U ud 3(5+2)= 21. ②3×5+2= 3k5+2= 17. ③ (5 + 3) × 2 = ( 5 + 3) k 2 = @u 3 π cos ⎯ [rad] = 4 J02 @y1= 10. 5@c2= 500 × 25% = 500 k 25 @ a 120 ÷ 400 = ?% 120 z 400 @ a 500 + (500 × 25%) = 500 + 25 @ a 400 − (400 × 30%) = 400 & 30 @ a 125. 30. 625. 280. |5 − 9| = @W5&9= 4. o @W(5&9 )= 4. • • • • • • • • • • • • • @>t( 5 z 7 ) = 0.895879734 RAD ln 20 = i 20 = 2.995732274 log 50 = l 50 = 1.698970004 log2 16384 = @ O 2 r 16384 = @ O 2 H 16384 ) = e3 = @"3= 1÷e= 1z;V = 1 7 14. GRAD 14. 0.367879441 −100 ≤ θ ≤ 100 0 ≤ θ ≤ 200 13 ⎯ 42 0.309523809 8mS2r &3m4r k5A= 33'333.33333 o ¥26,510 = $? 26510 z t Y = 241. U 33m20 $2,750 = ¥? 2750 k t Y = r = 3 cm (r ⇒ Y) 3xY πr 2 = ? s;Y A=U 24 2 ⎯ 2⎯ 4 + 6 = 5 …(A) 302'500. 3. 28.27433388 24 z ( 4 + 6 )= 3 k ; < + 60 z;<= sinh−1 ⇒ D1 xI@>v sinh−1 0.5 = I 0.5 = 0.481211825 6 + 4 = ANS j6+4= 10. ANS + 5 = +5= 15. 8 × 2 = ANS 8k2= 16. ANS2 = A= 44 + 37 = ANS 44 + 37 = 1 5 32 ⎯ 256. 81. 9. *= j3@k1d2r +W4d3= 5 6 4⎯ 29 ⎯ 6 → [g] sin−1 0.8 @] 90. @] → [°] = [°] - 63 ⎯ 64 129599 ⎯ 64 -2'024.984375 8mS2& 3m4k5 A= → [°] 8 -2024 @ w 0.8 = 53.13010235 53.13010235 @] ;txmM<IJK L 8×2⇒M j8k2xM 24 ÷ (8 × 2) = 24 z ; M = (8 × 2) × 5 = ;Mk5= 16. 1 1⎯ 2 80. -2'024.984375 U -2024m63m64 U -129599m64 4.833333333 3W1W2+4W3= 4m5m6* 29m6 4.833333333 10 3 = @Y2W3= ( ⎯75 ) 7W5rm5= 5 = o 4.641588834 16807 ⎯ 3125 @q1W8= 1 ⎯ 2 * 64 W 225 = 8 ⎯ 15 2 ⎯4 = 3 2@1W3m4= 8 ⎯ 81 o 2@1W(3m4) = 1 64 ⎯ = 225 3 BIN 11001 110101100 @ h 1AC BIN @z BIN PEN @r PEN 3203 OCT @g OCT 654 DEC @/ (1010 − 100) × 11 = @z( 1010 & 100) k 11 = [BIN] BIN (111) → NEG d 111 = HEX (1FF) + OCT (512) = HEX (?) 2FEC − 2C9E ⇒ M1 +) 2000 − 1901 ⇒ M2 — M= 428. 10010 BIN BIN 1111111001 @ h 1FF @g+ 512 = OCT 1511 @h HEX 349 jxM @ h 2FEC & 2C9E m HEX 34E 2000 &1901 m HEX 6FF tM jxM A4D HEX 1011 AND 101 = @ z 1011 4 101 = [BIN] BIN 1 5A OR C3 = [HEX] @ h 5A p C3 = HEX NOT 10110 = [BIN] @zn 10110 = BIN 1111101001 24 XOR 4 = [OCT] @ g 24 x4= OCT B3 XNOR 2D = [HEX] @ h B3 C 2D = HEX FFFFFFFF61 → DEC @/ 12 DB 20 -159. [: [10] j 7 [ 31 [ 49.44 @ : 7°31’49.44” 123.678 [60] 12 ⎯ 23 1.2 W 2.3 = 1°2’3” ⎯= 2 1[2[3W2= 0(31 q1.5" 1 × 10 ⎯ = 2 × 103 1`3W2`3= 1 ⎯ 2 7⇒A j7xA 7. 4 ⎯= A 4W;A= 4 ⎯ 7 123.678 @ : 663 1250 7⎯ 123(40q40.8" 3h 30m 45s + 6h 45m 36s = [60] 3 [ 30 [ 45 + 6 [ 45 [ 36 = 1234°56’12” + 0°0’34.567” = [60] 1234 [ 56 [ 12 + 0 [ 0 [ 34.567 = 1234(56 q47." 3h 45m – 1.69h = [60] 3 [ 45 & 1.69 =@: 8m81 1.2 ⎯= 2.3 3 j@/ 25 @ z 16807m3125 7W5m5= ⎯= 8 3 BIN HEX (1AC) Wk 1 4 3⎯ + ⎯ = 2 3 zrgh/dn4 pxC DEC (25) 9 2 100. 11 2 5 3 × (A) + 60 ÷ (A) = ⎯ 1 J ⎯ 2 5 * 4m5m6 = 4 ⎯ 6 2⎯ U j 90 @ ] 1.65 1m13m20 o ] 1.25 + 2 W 5 = U U 7 o 110. 0 ≤ θ ≤ 180 0≤θ≤π 1.65 110 x Y θ = cos−1 x π ≤θ≤⎯ π −⎯ 2 2 U $1 = ¥110 (110 ⇒ Y) U 90° → [rad] 20.08553692 U 8−2 − 34 × 52 = 35. U 5 tanh−1 ⎯ = 33 ⎯ 20 665. • −90 ≤ θ ≤ 90 U tM 10 θ = sin−1 x, θ = tan−1 x 13 20 1⎯ 250. tMk5@a @M ANS = 59.03344706 33.33b03 sin 62°12’24” = [10] v 62 [ 12 [ 24 = 13 10(16 q21." 2(3q36." 0.884635235 uEH ( ( rθ == [°] ( rθ == 1436 [°] ( xy == x=6 y=4 j6H4 @u r: {: 7.211102551 33.69006753 14 H 36 @E X: Y: 11.32623792 8.228993532 33'333.33333 J13 nJ S#a# 2 [QUAD] b12 18 0. x y 12 41 5 ⎯ 9 12 H 41 _ DATA SET= 1. 8 13 8 H 13 _ DATA SET= 2. 0.6 5 2 5H2_ DATA SET= 3. 1 k9=* 5.0 23 200 23 H 200 _ DATA SET= 4. 5z9= 5 ⎯ 9 15 71 15 H 71 _ DATA SET= 5. [FIX, TAB = 1] j J 1 0 1 0.0 5z9= U U 0.6 a= ta a= 5.357506761 3 ⎯ 5 b= tb b= -3.120289663 2 5 c= @n 5⎯ k 9 = *2 5.4 UU 5.4 J13 5 *1 ⎯ × 9 = 5.5555555555555 × 10−1 × 9 9 3 2 ⎯ * × 9 = 0.6 × 9 5 x = 10 y = 22 16 tS b 1 0 S#a# 0 [SD] @Z y´ = ? 10 @ U 10 y´ x´ = ? 22 @ V 22 x´ 1: 2: DATA 20 0. 40 DATA SET= 1. 40 80 80 _ DATA SET= 2. 50 80 75 75 75 50 _ DATA SET= 3. DATA SET= 5. 45 – x = 75.71428571 45 σx = tp σx = 12.37179148 45 n= Σx = tg Σx= Σx2 = to tv sx= 7. 530. 41'200. S#a# 1 [LINE] 0. y 2 5 2H5_ DATA SET= 1. 2 5 _ DATA SET= 2. 12 24 12 H 24 _ DATA SET= 3. 21 21 21 40 40 40 21 H 40 H 3 _ DATA SET= 4. 15 25 15 H 25 _ DATA SET= 5. a= ta a= 1.050261097 b= tb b= 1.826044386 r= tf r= 0.995176343 sx = tv sx = 8.541216597 sy = tG sy = 15.67223812 6.528394256 x=3 y´ = ? 3 @ U 3 y´ y = 46 x´ = ? 46 @ V 46 x´ 24.61590706 F: ■ 3_ X: d 60 _ 17 –x = Σ ⎯x σx = n x 2 − nx– 2 Σ⎯ n−1 sx = n 64.43210706 DATA SET= d d d 45 _ X: Σy – y= ⎯ ( 95 & ;R) ⎯ × 10 + 50 = z ; v sx k 10 + 50 = (95 − – x) DATA SET= d@# 60 13.3630621 sx2 = 178.5714286 A= DATA SET= 50 _ 4. tR DATA SET= 40 H 2 _ 75 H 3 _ DATA SET= – x = DATA SET= 30 _ DATA 30 tc 9.63201409 -3.432772026 S#a# 0 [SD] 20 _ 30 95 _ n= 24.4880159 _Hud# DATA 95 50 _ 0.503334057 c= b10 _HRvpcgoQ GsijhfabS VU x 720. @] [ENG: TAB 2] J 1 2 2 b11 24. → [g] 3.3b04 sx2 = 3. 6@Z+7 @Z= [SCI: SIG 2] J 1 1 2 DATA 50. U sx = @ q 27 = • U Σx2 = 4. 10 @ e 3 = = DEG DATA 15 = (cosh 1.5 + sinh 1.5)2 = j ( H $ 1.5 + H v 1.5 ) A = 20.08553692 7 * 49 & 4 @ D 81 = 4@B= 10P3 5C2 – M= 1 6 33'333.33 [NORM1] 4! = 4. ⎯+⎯= [FIX: TAB 2] J 1 0 2 ANS × 9 = 27 = 3p * 49 r & 4 @ D 81 = 2 1.25 + ⎯ = 1.25 + 2 W 5 = 5 450. 150 k 3 m +) $250: M1 + 250 ⇒ M2 250 m −) M2 × 5% 21. 17. j 100000 z 3 = o J00 J [MDF] 0.707106781 U tan−11 [g] = Q 2 ⎯ 2 p 49 − 4p 81 = $150 × 3 ⇒ M1 512. 0.927295218 ③ ANS × 9 = 0.866025403 8@1= @] 16. 5 ÷ 9 = ANS ⎯ 2 J01 $sW4= o 100000 ÷ 3 = 14 Q 3 83 = 6.447419591 → [rad] d [NORM1] 0. ( 12 m 3 ) m 1 W 4 = 6.447419591 @ Y 1.7 = 50.11872336 17. [NORM1] 2'720. o 0. jxM 0⇒M 101.7 = d u 1'700. ( 12 m 3 r)m 1W4= 16. ② ② 102. U o ① 3(5 + 2) = 91. j v 60 = 0. @Z ① sin 60 [°] = 3Q 5+5Q 2 ⎯ 15 0.918618116 U 2 1'250'000. @P0 H 15 3.872983346 U 2cos−1 0.5 [rad] = -90 40 = 1⎯ *3rk*5 = sin 45 = 3 7 3⎯ v$tw^ysH> ilO" VYZA1 *mDqBecaW H 6 U ⎯+⎯= 140. 5 68 × 40 = 1 0.003 j 3 z 1000 = [NORM1] (123) ⎯ 4 = sy = –2 Σ y 2 − ny ⎯ n−1 x 2 − nx– 2 Σ⎯ n Σx = x1 + x2 + … + xn Σx2 = x1 2 + x2 2 + … + xn2 Σy − 2 ny– 2 ⎯ n Σxy = x1 y1 + x2 y2 + … + xn yn Σy = y1 + y2 + … + yn Σy 2 = y1 2 + y2 2 + … + yn2 σy = Function keys Display Buffer space* Funktionstasten Anzeige Pufferplatz* Touches de fonction Affichage Espace tampon* Visualizador Espacio de memoria intermedia* Teclas de función Exibição Espaço na memória intermediária* Teclas de função Memoria tampone* Display Tasti di funzione Bufferruimte* Display Functietoetsen Pufferterület* Kijelző Függvénybillentyűk Vyrovnávací paměť* Zobrazení Tlačítka funkcí Buffertutrymme* Visning Funktionstangenter Puskuritila* Näyttö Funktionäppäimet Bufferplads* Display Funktionstaster * Tombol fungsi Function Funktion Fonction Función Função Funzioni Functie Függvény Funkce Funktion Funktio Funktion Dynamic range zulässiger Bereich Plage dynamique Rango dinámico Gama dinâmica Campi dinamici Rekencapaciteit Megengedett számítási tartomány Dynamický rozsah Definitionsområde Dynaaminen ala Dynamikområde Fungsi Kisaran dinamis Tampilan Ruang buffer* @Z □−1 1 A □2 1 @1 □3 1 m □□ 5 @O log□(□) 7 @" e□ 5 sin–1 x, cos–1 x |x| ≤ 1 5 tan x, P x | x | < 10100 ln x, log x, loga x 10–99 ≤ x < 10100, 10–99 ≤ a < 10100 (a ≠ 1) 10□ @Y 0. * P □ 5 1. @q 3P □ 5 □P 7 sin x, cos x, tan x DEG: | x | < 1010 (tan x : | x | ≠ 90(2n − 1))* π ⎯ RAD: | x | < 180 × 1010 π (tan x: | x | ≠ ⎯ (2n − 1))* 2 10 10 GRAD: | x | < ⎯ 9 × 10 (tan x: | x | ≠ 100(2n − 1))* –1 3 • y > 0: −10100 < x log y < 100 • y = 0: 0 < x < 10100 2. @D 3. W/@k □ ⎯ □ 7 (0 < | x | < 1: ⎯ x = 2n − 1, x ≠ 0)*, @W |□| 5 −10100 < x log | y | < 100 () ( 4 4. 3. 45. 3. 60. NOT BIN: 1000000000 ≤ x ≤ 1111111111 0 ≤ x ≤ 111111111 PEN: 2222222223 ≤ x ≤ 4444444444 0 ≤ x ≤ 2222222221 OCT: 4000000000 ≤ x ≤ 7777777777 0 ≤ x ≤ 3777777777 HEX: FDABF41C01 ≤ x ≤ FFFFFFFFFF 0 ≤ x ≤ 2540BE3FE NEG BIN: 1000000001 ≤ x ≤ 1111111111 0 ≤ x ≤ 111111111 PEN: 2222222223 ≤ x ≤ 4444444444 0 ≤ x ≤ 2222222222 OCT: 4000000001 ≤ x ≤ 7777777777 0 ≤ x ≤ 3777777777 HEX: FDABF41C01 ≤ x ≤ FFFFFFFFFF 0 ≤ x ≤ 2540BE3FF 19 □ ) * The amount of memory used for the sake of display in the WriteView editor, measured in characters (excluding entered values, denoted in the chart by “□”). * Der für die Anzeige in WriteView Editor verwendete Speicherplatz, gemessen in Zeichen (ohne die eingegebenen Werte, die in der Tabelle mit „□“ markiert sind). * Espace mémoire utilisé pour préserver l’affichage dans l’éditeur WriteView, mesuré en caractère (à l’exception des valeurs d’entrée, indiquées dans le tableau par “□”). * La cantidad de memoria usada para visualizar en el editor Write View, medida en caracteres (excluyendo los valores introducidos, indicados en el grafico mediante “□”). * A quantidade de memória que é usada para a exibição no editor WriteView, medida em caracteres (excluindo os valores introduzidos, indicados no quadro por “□”). * La quantità di memoria utilizzata per la visualizzazione nell’editor WriteView, misurata in caratteri (escludendo i valori inseriti, indicati nella tabella con il simbolo “□”). * De hoeveelheid geheugen dat wordt gebruikt om de WriteView editor weer te geven, gemeten in symbolen (met uitzondering van ingevoerde waarden aangeduid in de grafiek met “□”). * A WriteView szerkesztő megjelenítési műveleteire használatos memóriaterület, karakterben kifejezve (az ábrán „□” karakterrel jelölt beviteli értékeket nem számítva). * Množství paměti využívané pro účely zobrazení v editoru WriteView, vyjádřené počtem znaků (vyjma zadaných hodnot, označených v grafu znakem „□“). * Den mängd minne som används för visning med WriteViewredigeraren, mätt i antalet tecken (exklusive inmatade värden, vilka anges som ”□” i tabellen). * Näytön WriteView-editorissa käyttämä muisti merkkeinä laskettuna (pois lukien syötetyt arvot, taulukossa merkitty ”□”). * Den mængde hukommelse, der bruges til visning i WriteVieweditoren, målt i tegn (med undtagelse af indtastede værdier, der angives med „□“ i tabellen). x=n 1 1 −10100 < ⎯ x log y < 100 (x ≠ 0) • y = 0: 0 < x < 10100 • y < 0: x = 2n − 1 1 (0 < | x | < 1: ⎯ x = n, x ≠ 0)*, • y > 0: x y P 1 −10100 < ⎯ x log | y | < 100 ex −10100 < x ≤ 230.2585092 10 x −10100 < x < 100 sinh x, cosh x, tanh x | x | ≤ 230.2585092 sinh x | x | < 1050 cosh–1 x 1 ≤ x < 1050 –1 |x| < 1 x2 | x | < 1050 x3 | x | < 2.15443469 × 1033 x P 0 ≤ x < 10100 x –1 | x | < 10100 (x ≠ 0) n! 0 ≤ n ≤ 69* 0 ≤ r ≤ n ≤ 9999999999* n! ⎯ (n − r)! nPr Umweltschutz Das Gerät wird durch eine Batterie mit Strom versorgt. Um die Batterie sicher und umweltschonend zu entsorgen, beachten Sie bitte folgende Punkte: • Bringen Sie die leere Batterie zu Ihrer örtlichen Mülldeponie, zum Händler oder zum KundenserviceZentrum zur Wiederverwertung. • Werfen Sie die leere Batterie niemals ins Feuer, ins Wasser oder in den Hausmüll. Seulement pour la France/For France only: Protection de l’environnement L’appareil est alimenté par pile. Afin de protéger l’environnement, nous vous recommandons: • d’apporter la pile usagée ou à votre revendeur ou au service après-vente, pour recyclage. • de ne pas jeter la pile usagée dans une source de chaleur, dans l’eau ou dans un vide-ordures. Endast svensk version/For Sweden only: Miljöskydd Denna produkt drivs av batteri. Vid batteribyte skall följande iakttagas: • Det förbrukade batteriet skall inlämnas till batteriinsamling eller till kommunal miljöstation för återinssamling. • Kasta ej batteriet i vattnet eller i hushållssoporna. Batteriet får ej heller utsättas för öppen eld. OPMERKING: ALLEEN VOOR NEDERLAND/ NOTE: FOR NETHERLANDS ONLY 100 0 ≤ r ≤ n ≤ 9999999999* 0 ≤ r ≤ 69 nCr n! ⎯ (n − r)! ↕DEG, D°M’S r, θ < 10 Nur für Deutschland/For Germany only: For Europe only: tanh x –1 x, y * Jumlah memori yang digunakan untuk kepentingan tampilan dalam editor WriteView, diukur dalam jumlah karakter (tidak termasuk nilai yang dimasukkan, ditunjukkan dalam diagram dengan “□”) • y < 0: yx * n, r: integer / ganze Zahlen / entier / entero / inteiro / intero / geheel getal / egész számok / celé číslo / heltal / kokonaisluku / heltal / / / bilangan bulat r, θ x, y < 10100 0°0’0.00001” ≤ | x | < 10000° x 2 + y 2 < 10100 0 ≤ r < 10100 DEG: | θ | < 1010 π ⎯ RAD: | θ | < 180 × 1010 10 10 GRAD: | θ | < ⎯ 9 × 10 DEG DRG▶ DEC BIN PEN OCT HEX AND OR XOR XNOR RAD RAD, GRAD DEG: | x | < 10100 π GRAD: | x | < ⎯ 1098 2 × DEC: | x | ≤ 9999999999 BIN: 1000000000 ≤ x ≤ 1111111111 0 ≤ x ≤ 111111111 PEN: 2222222223 ≤ x ≤ 4444444444 0 ≤ x ≤ 2222222222 OCT: 4000000000 ≤ x ≤ 7777777777 0 ≤ x ≤ 3777777777 HEX: FDABF41C01 ≤ x ≤ FFFFFFFFFF 0 ≤ x ≤ 2540BE3FF A. Information on Disposal for Users (private households) 1. In the European Union Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin! Used electrical and electronic equipment must be treated separately and in accordance Attention: Your product with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment. is marked with this Following the implementation by member states, private households within the EU states symbol. It means that may return their used electrical and electronic equipment to designated collection facilities used electrical and free of charge*. In some countries* your local retailer may also take back your old product electronic products free of charge if you purchase a similar new one. should not be mixed with general household *) Please contact your local authority for further details. waste. There is a If your used electrical or electronic equipment has batteries or accumulators, please separate collection dispose of these separately beforehand according to local requirements. system for these By disposing of this product correctly you will help ensure that the waste undergoes the products. necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due to inappropriate waste handling. 2. In other Countries outside the EU If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal. For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch. ENGLISH B. Information on Disposal for Business Users. 1. In the European Union If the product is used for business purposes and you want to discard it: Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection facilities. For Spain: Please contact the established collection system or your local authority for take-back of your used products. 2. In other Countries outside the EU If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal. For Australia/New Zealand only: For warranty information please see www.sharp.net.au.

Download PDF

- Similar pages
- Resetting the CASIO fx-9750GII for testing purposes
- Gear Head KP3200CW Computer Keyboard User Manual
- 4325 SPEC SHEET front.ai
- Casio H-1 Instruction manual
- Calculating on the Casio cfx-9850G Plus
- Resetting the PRIZM
- Casio fx-300W User`s guide
- Casio FX 7400G - Co., Ltd - Graphing Calculator User`s guide
- Sharp EL-506VB Calculator
- Casio FX-820MS User`s guide