v2.0 (1.0.2.0) (EN/F)
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE
user manual
guide de l’utilisateur
RC100
EN/F
It is important to read this user manual prior to using your new product for the first time.
Nous vous recommandons de lire ce manuel d’instructions avant d’utiliser votre
nouveau produit pour la première fois.
FCC Information
Note: This equipment has been tested
and found to comply with the limits
for a Class B digital device, pursuant
to Part 15 of FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee
that interference will not occur in a
particular installation. If this equipment
does cause harmful interference to
radio or television reception, which
can be determined by turning the
equipment off and on, the user is
encouraged to try to correct the
interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from
that to which the receiver is
connected.
• Consult the dealer or an
experienced radio/TV technician for
help.
1. To set time for alarm, press and
hold ALARM SET/OFF and press
HRS or MIN simultaneously.
2. To save and exit the alarm setting,
release ALARM SET/OFF.
Selecting wake source
You may be woken up by radio or
alarm.
1. Set a wake time (see above
instructions).
2. Slide ON/OFF/RADIO(WAKE)/
ALARM(WAKE) to RADIO or
ALARM to select a waking mode
(by radio or alarm).
• Your last tuned radio station will be
the wake source if wake by radio is
selected.
Some of the following information may
not apply to your particular product;
however, as with any electronic product,
precautions should be observed during
handling and use.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near
water.
• Clean only with dry cloth.
• Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
• Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
• Do not defeat the safety purpose
of the polarized or grounding-type
plug. A polarized plug has two
blades with one wider than the
other. A grounding type plug has
•
•
•
•
Before you begin
Changes or modifications not expressly
approved by Audiovox could void
the user’s authority to operate the
equipment.
Refer to the “Clock” section and
follow the instructions to set the
clock.
Battery back-up operation
This Class B digital apparatus
complies with Canadian ICES-003.
Cet appareil numérique de la classe
B est conforme à la norme NMB-003
du Canada.
Electrical power
information
Power Supply: 120 V ~ 60 Hz
Power Consumption: 5 Watts
• This clock radio is equipped with
a memory holding system that can
be powered with a 9-volt alkaline
battery (not included). The power
failure protection circuit will not
operate unless battery is installed.
• When normal household power
is interrupted, or AC line cord
is unplugged, the batteries will
power the clock radio to keep
track of time and alarm settings
programmed into memory.
• When the battery backup functions,
the digital display will not light,
however, the function of alarm
still occurs during the power
interruption if remaining battery
power is adequate.
• Normal operation will resume after
AC power is restored so you will not
have to reset the time or the alarm.
To install the battery:
1. Remove battery compartment door
(located at the bottom of the radio)
by applying thumb pressure to the
tab on battery door and then lift
the door out and off the cabinet.
2. Connect a 9-volt alkaline battery
(not included) to the connector
plug.
3. Replace the compartment door.
Wake function
Setting wake time
•
two blades and a third grounding
prong. The wide blade or the third
prong is provided for your safety. If
the provided plug does not fit into
your outlet, consult an electrician
for replacement of the obsolete
outlet.
Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
Only use attachments/accessories
specified by the manufacturer.
Use only with
the cart, stand,
]
tripod, bracket,
or table
specified by the
manufacturer,
Portable Cart Warning
or sold with
the apparatus.
When a cart is used, use caution
when moving the cart/apparatus
combination to avoid injury from
tip-over.
Unplug this apparatus during
lightning storms or when unused
for long periods of time.
Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as power-supply cord or plug is
damaged, liquid has been spilled
or objects have fallen into the
apparatus, the apparatus has been
Turning off the wake
alarm or radio
• To silence the wake function
momentarily:
To turn off the wake function, press
SNOOZE/SLEEP OFF on the top of
the unit. The wake alarm or radio
will be switched off temporarily.
The alarm or radio will be on again
when the snooze period (9 minutes)
is over.
Snooze function can be used
repeatedly up to 2 hours. After this,
the alarm will turn off until the
next alarm conditions are met.
• To turn off the wake alarm or
radio:
Press ALARM SET/OFF. The wake
alarm or radio will activate again
the next day unless you switch off
the Wake function.
• To disable the wake function
completely:
Slide ON/OFF/RADIO(WAKE)/
ALARM(WAKE) to OFF.
Power failure indicator
exposed to rain or moisture, does
not operate normally, or has been
dropped.
ADDITIONAL SAFETY INFORMATION
• Apparatus shall not be exposed to
dripping or splashing and no objects
filled with liquids, such as vases,
shall be placed on the apparatus.
• Always leave sufficient space around
the product for ventilation. Do
not place product in or on a bed,
rug, in a bookcase or cabinet that
may prevent air flow through vent
openings.
• Do not place lighted candles,
cigarettes, cigars, etc. on the
product.
• Connect power cord only to AC
power source as marked on the
product.
• Care should be taken so that objects
do not fall into the product.
• Do not attempt to disassemble
the cabinet. This product does
not contain customer serviceable
components.
• The marking information is located
at the bottom of apparatus.
• To be completely disconnect the
power input, the mains plug of
apparatus shall be disconnected
from the mains.
• Mains plug is a disconnect device.
The mains plug should not be
obstructed OR should be easily
accessed during intended use.
• The ventilation should not be
Ecology
Help protect the environment - we
recommend that you dispose of used
batteries by putting them into specially
designed receptacles.
Radio
Right view
Setting clock
Selecting radio mode
1. Press and hold TIME.
Slide ON/OFF/RADIO(WAKE)/
ALARM(WAKE) to ON to switch on
radio. Slide to OFF to switch off radio.
When AC power is interrupted
(disconnected) for a short period of
time, both time and alarm settings
will change (unless batteries are
installed). After AC power is restored
(reconnected), the Digital Display
will blink to indicate that power was
interrupted and you should re-adjust
the time and alarm settings.
• – VOLUME + – To adjust volume
• TUNING – To adjust radio frequency
Alkaline (NEDA 1604A/
IEC 6LR61) battery is
recommended. Carbon-zinc
battery may be used but memory
holding time will be substantially
reduced. Memory holding time
for a fresh alkaline battery is
approximately 8 hours (if radio
or alarm are not operated) which
should take care of short, nuisancetype AC power failures. To preserve
battery life, the unit should remain
plugged into an AC outlet. As the
battery gets older, its voltage drops
and memory may be lost. Be sure
to replace the battery periodically.
Battery should be removed if the
unit will be stored for more than
one month. Leaky battery can
badly damage the clock radio.
2. Press HRS or MIN to set the clock
time.
• AM indicator lights when the time is
set to AM.
• PM indicator lights when the time is
set to PM.
3. To save and exit the clock setting,
release TIME.
Top view
• ON/OFF/RADIO(WAKE)/
ALARM(WAKE) – To turn radio on
or off; to change wake mode (radio/
alarm)
• TIME – To adjust the clock time
• ALARM SET – To activate the wake
settings
• SLEEP – To activate sleep function
• AM/FM – To select radio band
• HRS – To adjust hour value when
setting clock, wake and sleep modes
• MIN – To adjust the minute value
when setting clock, wake and sleep
modes
• SNOOZE/SLEEP OFF – To quiet
the wake alarm or wake radio
temporarily (9 minutes); to cancel
sleep function
Switching band
Slide the band switch AM/FM to select
FM or AM band.
Tuning the radio
Rotate the TUNING knob on the
right of the unit to adjust the radio
frequency with reference to the tuning
dial scale.
Built-in AFC
The Built In Automatic Frequency
Control (AFC) works only on FM. It helps
reducing drift on FM reception and
keeping the radio locked in on the FM
station to which it is tuned.
When tuning in FM stations, you may
notice that the station you are tuning
can be well-tuned on two or three
nearby points on the dial. Always tune
carefully at the loudest and clearest
point.
AM antenna
A built-in ferrite rod antenna eliminates
the need for an outside antenna for
AM reception. Rotating the unit slightly
may improve reception of distant AM
stations.
Set sleep time manually
12 Month Limited Warranty
Applies to RCA Clock Radios
players, home networks or vehicle
electrical systems.
AUDIOVOX ACCESSORIES CORP. (the
Company) warrants to the original retail
purchaser of this product that should
this product or any part thereof, under
normal use and conditions, be proven
defective in material or workmanship
within 12 months from the date of
original purchase, such defect(s) will be
repaired or replaced with reconditioned
product (at the Company’s option)
without charge for parts and repair
labor.
This Warranty does not apply to any
product or part thereof which, in the
opinion of the Company, has suffered
or been damaged through alteration,
improper installation, mishandling,
misuse, neglect, accident, or by removal
or defacement of the factory serial
number/bar code label(s). THE EXTENT
OF THE COMPANY’S LIABILITY UNDER
THIS WARRANTY IS LIMITED TO THE
REPAIR OR REPLACEMENT PROVIDED
ABOVE AND, IN NO EVENT, SHALL THE
COMPANY’S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT.
To cancel the sleep mode:
• Press SNOOZE/SLEEP OFF to cancel
the sleep mode and turn off the
unit.
AC OUTLET POWER SUPPLY:
120 V ~ 60 Hz
The AC power plug is
polarized (one blade is
wider than the other)
and only fits into AC
power outlets one
way. If the plug will
not go into the outlet
completely, turn the plug over and try
to insert it the other way. If it still does
not fit, contact a qualified electrician
to change the outlet, or use a different
one. Do not attempt to bypass this
safety feature.
• Any battery may present a risk of
fire, explosion, or chemical burn
if abused. Do not try to charge a
battery that is not intended to be
recharged, do not incinerate, and
do not puncture.
• Non-rechargeable batteries, such as
alkaline batteries, may leak if left in
your product for a long period of
time. Remove the batteries from the
product if you are not going to use
it for a month or more.
• If your product uses more than one
battery, do not mix types and make
sure they are inserted correctly.
Mixing types or inserting incorrectly
may cause them to leak.
• Discard any leaky or deformed
battery immediately. They may
cause skin burns or other personal
injury.
• Please help to protect the
environment by recycling or
disposing of batteries according to
federal, state, and local regulations.
WARNING: The battery (battery or
batteries or battery pack) shall not
be exposed to excessive heat such as
sunshine, fire or the like.
Clock
Warranty information
To set the sleep mode:
1. Press and hold SLEEP and press
MIN simultaneously to adjust the
sleep time. The time range is from
from 0:01 to 1:59. (The default time
is 59 minutes.)
• The radio will be switched on.
Plugging in for power
Important battery
precautions
General controls
Sleep function
In sleep function, the unit will turn off
automatically after a specified time.
impeded by covering the ventilation
openings with items such as
newspaper, table-cloths, curtains etc.
• No naked flame sources, such as
lighted candled, should be placed
on the apparatus.
• Attention should be drawn to the
environmental aspects of battery
disposal.
• The use of apparatus in moderate
climates.
This is class II
equipment designed
with double or
reinforced insulation
so it does not require
a safety connection to
electrical earth (US:
ground).
To obtain repair or replacement
within the terms of this Warranty, the
product is to be delivered with proof
of warranty coverage (e.g. dated bill
of sale), specification of defect(s),
transportation prepaid, to the Company
at the address shown below.
This Warranty does not extend to the
elimination of externally generated
static or noise, to correction of
antenna problems, loss/interruptions of
broadcast or internet service, to costs
incurred for installation, removal or
reinstallation of product, to corruptions
caused by computer viruses, spyware or
other malware, to loss of media, files,
data or content, or to damage to tapes,
discs, removable memory devices or
cards, speakers, accessories, computers,
computer peripherals, other media
This Warranty is in lieu of all other
express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING
ANY IMPLIED WARRANTY OF
MERCHANTABILITY, SHALL BE LIMITED
TO THE DURATION OF THIS WRITTEN
WARRANTY. ANY ACTION FOR BREACH
OF ANY WARRANTY HEREUNDER
INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY MUST BE
BROUGHT WITHIN A PERIOD OF 24
MONTHS FROM DATE OF ORIGINAL
PURCHASE. IN NO CASE SHALL THE
COMPANY BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR
ANY OTHER WARRANTY. No person or
representative is authorized to assume
for the Company any liability other than
expressed herein in connection with the
sale of this product.
Some states do not allow limitations on
how long an implied warranty lasts or
the exclusion or limitation of incidental
or consequential damage so the above
limitations or exclusions may not apply
to you. This Warranty gives you specific
legal rights and you may also have
other rights which vary from state to
state.
Recommendations before returning
your product for a warranty claim:
• Properly pack your unit. Include
any remotes, memory cards, cables,
etc. which were originally provided
with the product. However DO NOT
return any removable batteries,
even if batteries were included
with the original purchase. We
recommend using the original
carton and packing materials. Ship
to the address shown below.
• Note that product will be returned
with factory default settings.
Consumer will be responsible to
restore any personal preference
settings.
Audiovox Electronics Corp.
Attn: Service Department.
150 Marcus Blvd.
Hauppauge N.Y. 11788
1-800-645-4994
For Canada Customers, please ship to:
Audiovox Return Centre
c/o Genco
6685 Kennedy Road,
Unit#3, Door 16,
Mississuaga, Ontario
L5T 3A5
Illustrations contained within this
publication are for representation only
and subject to change.
The descriptions and characteristics
given in this document are given as
a general indication and not as a
guarantee. In order to provide the
highest quality product possible,
we reserve the right to make any
improvement or modification without
prior notice.
Visit http://store.audiovox.com to find the best
accessories for your products.
© 2011 Audiovox Accessories Corporation
111 Congressional Blvd., Suite 350
Carmel, IN 46032
Trademark(s) ® Registered
Printed in China
v2.0 (1.0.2.0) (EN/F)
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE
user manual
guide de l’utilisateur
RC100
EN/F
It is important to read this user manual prior to using your new product for the first time.
Nous vous recommandons de lire ce manuel d’instructions avant d’utiliser votre
nouveau produit pour la première fois.
FCC Information
Note: This equipment has been tested
and found to comply with the limits
for a Class B digital device, pursuant
to Part 15 of FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee
that interference will not occur in a
particular installation. If this equipment
does cause harmful interference to
radio or television reception, which
can be determined by turning the
equipment off and on, the user is
encouraged to try to correct the
interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from
that to which the receiver is
connected.
• Consult the dealer or an
experienced radio/TV technician for
help.
1. To set time for alarm, press and
hold ALARM SET/OFF and press
HRS or MIN simultaneously.
2. To save and exit the alarm setting,
release ALARM SET/OFF.
Selecting wake source
You may be woken up by radio or
alarm.
1. Set a wake time (see above
instructions).
2. Slide ON/OFF/RADIO(WAKE)/
ALARM(WAKE) to RADIO or
ALARM to select a waking mode
(by radio or alarm).
• Your last tuned radio station will be
the wake source if wake by radio is
selected.
Some of the following information may
not apply to your particular product;
however, as with any electronic product,
precautions should be observed during
handling and use.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near
water.
• Clean only with dry cloth.
• Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
• Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
• Do not defeat the safety purpose
of the polarized or grounding-type
plug. A polarized plug has two
blades with one wider than the
other. A grounding type plug has
•
•
•
•
Before you begin
Changes or modifications not expressly
approved by Audiovox could void
the user’s authority to operate the
equipment.
Refer to the “Clock” section and
follow the instructions to set the
clock.
Battery back-up operation
This Class B digital apparatus
complies with Canadian ICES-003.
Cet appareil numérique de la classe
B est conforme à la norme NMB-003
du Canada.
Electrical power
information
Power Supply: 120 V ~ 60 Hz
Power Consumption: 5 Watts
• This clock radio is equipped with
a memory holding system that can
be powered with a 9-volt alkaline
battery (not included). The power
failure protection circuit will not
operate unless battery is installed.
• When normal household power
is interrupted, or AC line cord
is unplugged, the batteries will
power the clock radio to keep
track of time and alarm settings
programmed into memory.
• When the battery backup functions,
the digital display will not light,
however, the function of alarm
still occurs during the power
interruption if remaining battery
power is adequate.
• Normal operation will resume after
AC power is restored so you will not
have to reset the time or the alarm.
To install the battery:
1. Remove battery compartment door
(located at the bottom of the radio)
by applying thumb pressure to the
tab on battery door and then lift
the door out and off the cabinet.
2. Connect a 9-volt alkaline battery
(not included) to the connector
plug.
3. Replace the compartment door.
Wake function
Setting wake time
•
two blades and a third grounding
prong. The wide blade or the third
prong is provided for your safety. If
the provided plug does not fit into
your outlet, consult an electrician
for replacement of the obsolete
outlet.
Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
Only use attachments/accessories
specified by the manufacturer.
Use only with
the cart, stand,
]
tripod, bracket,
or table
specified by the
manufacturer,
Portable Cart Warning
or sold with
the apparatus.
When a cart is used, use caution
when moving the cart/apparatus
combination to avoid injury from
tip-over.
Unplug this apparatus during
lightning storms or when unused
for long periods of time.
Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as power-supply cord or plug is
damaged, liquid has been spilled
or objects have fallen into the
apparatus, the apparatus has been
Turning off the wake
alarm or radio
• To silence the wake function
momentarily:
To turn off the wake function, press
SNOOZE/SLEEP OFF on the top of
the unit. The wake alarm or radio
will be switched off temporarily.
The alarm or radio will be on again
when the snooze period (9 minutes)
is over.
Snooze function can be used
repeatedly up to 2 hours. After this,
the alarm will turn off until the
next alarm conditions are met.
• To turn off the wake alarm or
radio:
Press ALARM SET/OFF. The wake
alarm or radio will activate again
the next day unless you switch off
the Wake function.
• To disable the wake function
completely:
Slide ON/OFF/RADIO(WAKE)/
ALARM(WAKE) to OFF.
Power failure indicator
exposed to rain or moisture, does
not operate normally, or has been
dropped.
ADDITIONAL SAFETY INFORMATION
• Apparatus shall not be exposed to
dripping or splashing and no objects
filled with liquids, such as vases,
shall be placed on the apparatus.
• Always leave sufficient space around
the product for ventilation. Do
not place product in or on a bed,
rug, in a bookcase or cabinet that
may prevent air flow through vent
openings.
• Do not place lighted candles,
cigarettes, cigars, etc. on the
product.
• Connect power cord only to AC
power source as marked on the
product.
• Care should be taken so that objects
do not fall into the product.
• Do not attempt to disassemble
the cabinet. This product does
not contain customer serviceable
components.
• The marking information is located
at the bottom of apparatus.
• To be completely disconnect the
power input, the mains plug of
apparatus shall be disconnected
from the mains.
• Mains plug is a disconnect device.
The mains plug should not be
obstructed OR should be easily
accessed during intended use.
• The ventilation should not be
Ecology
Help protect the environment - we
recommend that you dispose of used
batteries by putting them into specially
designed receptacles.
Radio
Right view
Setting clock
Selecting radio mode
1. Press and hold TIME.
Slide ON/OFF/RADIO(WAKE)/
ALARM(WAKE) to ON to switch on
radio. Slide to OFF to switch off radio.
When AC power is interrupted
(disconnected) for a short period of
time, both time and alarm settings
will change (unless batteries are
installed). After AC power is restored
(reconnected), the Digital Display
will blink to indicate that power was
interrupted and you should re-adjust
the time and alarm settings.
• – VOLUME + – To adjust volume
• TUNING – To adjust radio frequency
Alkaline (NEDA 1604A/
IEC 6LR61) battery is
recommended. Carbon-zinc
battery may be used but memory
holding time will be substantially
reduced. Memory holding time
for a fresh alkaline battery is
approximately 8 hours (if radio
or alarm are not operated) which
should take care of short, nuisancetype AC power failures. To preserve
battery life, the unit should remain
plugged into an AC outlet. As the
battery gets older, its voltage drops
and memory may be lost. Be sure
to replace the battery periodically.
Battery should be removed if the
unit will be stored for more than
one month. Leaky battery can
badly damage the clock radio.
2. Press HRS or MIN to set the clock
time.
• AM indicator lights when the time is
set to AM.
• PM indicator lights when the time is
set to PM.
3. To save and exit the clock setting,
release TIME.
Top view
• ON/OFF/RADIO(WAKE)/
ALARM(WAKE) – To turn radio on
or off; to change wake mode (radio/
alarm)
• TIME – To adjust the clock time
• ALARM SET – To activate the wake
settings
• SLEEP – To activate sleep function
• AM/FM – To select radio band
• HRS – To adjust hour value when
setting clock, wake and sleep modes
• MIN – To adjust the minute value
when setting clock, wake and sleep
modes
• SNOOZE/SLEEP OFF – To quiet
the wake alarm or wake radio
temporarily (9 minutes); to cancel
sleep function
Switching band
Slide the band switch AM/FM to select
FM or AM band.
Tuning the radio
Rotate the TUNING knob on the
right of the unit to adjust the radio
frequency with reference to the tuning
dial scale.
Built-in AFC
The Built In Automatic Frequency
Control (AFC) works only on FM. It helps
reducing drift on FM reception and
keeping the radio locked in on the FM
station to which it is tuned.
When tuning in FM stations, you may
notice that the station you are tuning
can be well-tuned on two or three
nearby points on the dial. Always tune
carefully at the loudest and clearest
point.
AM antenna
A built-in ferrite rod antenna eliminates
the need for an outside antenna for
AM reception. Rotating the unit slightly
may improve reception of distant AM
stations.
Set sleep time manually
12 Month Limited Warranty
Applies to RCA Clock Radios
players, home networks or vehicle
electrical systems.
AUDIOVOX ACCESSORIES CORP. (the
Company) warrants to the original retail
purchaser of this product that should
this product or any part thereof, under
normal use and conditions, be proven
defective in material or workmanship
within 12 months from the date of
original purchase, such defect(s) will be
repaired or replaced with reconditioned
product (at the Company’s option)
without charge for parts and repair
labor.
This Warranty does not apply to any
product or part thereof which, in the
opinion of the Company, has suffered
or been damaged through alteration,
improper installation, mishandling,
misuse, neglect, accident, or by removal
or defacement of the factory serial
number/bar code label(s). THE EXTENT
OF THE COMPANY’S LIABILITY UNDER
THIS WARRANTY IS LIMITED TO THE
REPAIR OR REPLACEMENT PROVIDED
ABOVE AND, IN NO EVENT, SHALL THE
COMPANY’S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT.
To cancel the sleep mode:
• Press SNOOZE/SLEEP OFF to cancel
the sleep mode and turn off the
unit.
AC OUTLET POWER SUPPLY:
120 V ~ 60 Hz
The AC power plug is
polarized (one blade is
wider than the other)
and only fits into AC
power outlets one
way. If the plug will
not go into the outlet
completely, turn the plug over and try
to insert it the other way. If it still does
not fit, contact a qualified electrician
to change the outlet, or use a different
one. Do not attempt to bypass this
safety feature.
• Any battery may present a risk of
fire, explosion, or chemical burn
if abused. Do not try to charge a
battery that is not intended to be
recharged, do not incinerate, and
do not puncture.
• Non-rechargeable batteries, such as
alkaline batteries, may leak if left in
your product for a long period of
time. Remove the batteries from the
product if you are not going to use
it for a month or more.
• If your product uses more than one
battery, do not mix types and make
sure they are inserted correctly.
Mixing types or inserting incorrectly
may cause them to leak.
• Discard any leaky or deformed
battery immediately. They may
cause skin burns or other personal
injury.
• Please help to protect the
environment by recycling or
disposing of batteries according to
federal, state, and local regulations.
WARNING: The battery (battery or
batteries or battery pack) shall not
be exposed to excessive heat such as
sunshine, fire or the like.
Clock
Warranty information
To set the sleep mode:
1. Press and hold SLEEP and press
MIN simultaneously to adjust the
sleep time. The time range is from
from 0:01 to 1:59. (The default time
is 59 minutes.)
• The radio will be switched on.
Plugging in for power
Important battery
precautions
General controls
Sleep function
In sleep function, the unit will turn off
automatically after a specified time.
impeded by covering the ventilation
openings with items such as
newspaper, table-cloths, curtains etc.
• No naked flame sources, such as
lighted candled, should be placed
on the apparatus.
• Attention should be drawn to the
environmental aspects of battery
disposal.
• The use of apparatus in moderate
climates.
This is class II
equipment designed
with double or
reinforced insulation
so it does not require
a safety connection to
electrical earth (US:
ground).
To obtain repair or replacement
within the terms of this Warranty, the
product is to be delivered with proof
of warranty coverage (e.g. dated bill
of sale), specification of defect(s),
transportation prepaid, to the Company
at the address shown below.
This Warranty does not extend to the
elimination of externally generated
static or noise, to correction of
antenna problems, loss/interruptions of
broadcast or internet service, to costs
incurred for installation, removal or
reinstallation of product, to corruptions
caused by computer viruses, spyware or
other malware, to loss of media, files,
data or content, or to damage to tapes,
discs, removable memory devices or
cards, speakers, accessories, computers,
computer peripherals, other media
This Warranty is in lieu of all other
express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING
ANY IMPLIED WARRANTY OF
MERCHANTABILITY, SHALL BE LIMITED
TO THE DURATION OF THIS WRITTEN
WARRANTY. ANY ACTION FOR BREACH
OF ANY WARRANTY HEREUNDER
INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY MUST BE
BROUGHT WITHIN A PERIOD OF 24
MONTHS FROM DATE OF ORIGINAL
PURCHASE. IN NO CASE SHALL THE
COMPANY BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR
ANY OTHER WARRANTY. No person or
representative is authorized to assume
for the Company any liability other than
expressed herein in connection with the
sale of this product.
Some states do not allow limitations on
how long an implied warranty lasts or
the exclusion or limitation of incidental
or consequential damage so the above
limitations or exclusions may not apply
to you. This Warranty gives you specific
legal rights and you may also have
other rights which vary from state to
state.
Recommendations before returning
your product for a warranty claim:
• Properly pack your unit. Include
any remotes, memory cards, cables,
etc. which were originally provided
with the product. However DO NOT
return any removable batteries,
even if batteries were included
with the original purchase. We
recommend using the original
carton and packing materials. Ship
to the address shown below.
• Note that product will be returned
with factory default settings.
Consumer will be responsible to
restore any personal preference
settings.
Audiovox Electronics Corp.
Attn: Service Department.
150 Marcus Blvd.
Hauppauge N.Y. 11788
1-800-645-4994
For Canada Customers, please ship to:
Audiovox Return Centre
c/o Genco
6685 Kennedy Road,
Unit#3, Door 16,
Mississuaga, Ontario
L5T 3A5
Illustrations contained within this
publication are for representation only
and subject to change.
The descriptions and characteristics
given in this document are given as
a general indication and not as a
guarantee. In order to provide the
highest quality product possible,
we reserve the right to make any
improvement or modification without
prior notice.
Visit http://store.audiovox.com to find the best
accessories for your products.
© 2011 Audiovox Accessories Corporation
111 Congressional Blvd., Suite 350
Carmel, IN 46032
Trademark(s) ® Registered
Printed in China
v2.0 (1.0.2.0) (EN/F)
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE
user manual
guide de l’utilisateur
RC100
EN/F
It is important to read this user manual prior to using your new product for the first time.
Nous vous recommandons de lire ce manuel d’instructions avant d’utiliser votre
nouveau produit pour la première fois.
FCC Information
Note: This equipment has been tested
and found to comply with the limits
for a Class B digital device, pursuant
to Part 15 of FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee
that interference will not occur in a
particular installation. If this equipment
does cause harmful interference to
radio or television reception, which
can be determined by turning the
equipment off and on, the user is
encouraged to try to correct the
interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from
that to which the receiver is
connected.
• Consult the dealer or an
experienced radio/TV technician for
help.
1. To set time for alarm, press and
hold ALARM SET/OFF and press
HRS or MIN simultaneously.
2. To save and exit the alarm setting,
release ALARM SET/OFF.
Selecting wake source
You may be woken up by radio or
alarm.
1. Set a wake time (see above
instructions).
2. Slide ON/OFF/RADIO(WAKE)/
ALARM(WAKE) to RADIO or
ALARM to select a waking mode
(by radio or alarm).
• Your last tuned radio station will be
the wake source if wake by radio is
selected.
Some of the following information may
not apply to your particular product;
however, as with any electronic product,
precautions should be observed during
handling and use.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near
water.
• Clean only with dry cloth.
• Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
• Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
• Do not defeat the safety purpose
of the polarized or grounding-type
plug. A polarized plug has two
blades with one wider than the
other. A grounding type plug has
•
•
•
•
Before you begin
Changes or modifications not expressly
approved by Audiovox could void
the user’s authority to operate the
equipment.
Refer to the “Clock” section and
follow the instructions to set the
clock.
Battery back-up operation
This Class B digital apparatus
complies with Canadian ICES-003.
Cet appareil numérique de la classe
B est conforme à la norme NMB-003
du Canada.
Electrical power
information
Power Supply: 120 V ~ 60 Hz
Power Consumption: 5 Watts
• This clock radio is equipped with
a memory holding system that can
be powered with a 9-volt alkaline
battery (not included). The power
failure protection circuit will not
operate unless battery is installed.
• When normal household power
is interrupted, or AC line cord
is unplugged, the batteries will
power the clock radio to keep
track of time and alarm settings
programmed into memory.
• When the battery backup functions,
the digital display will not light,
however, the function of alarm
still occurs during the power
interruption if remaining battery
power is adequate.
• Normal operation will resume after
AC power is restored so you will not
have to reset the time or the alarm.
To install the battery:
1. Remove battery compartment door
(located at the bottom of the radio)
by applying thumb pressure to the
tab on battery door and then lift
the door out and off the cabinet.
2. Connect a 9-volt alkaline battery
(not included) to the connector
plug.
3. Replace the compartment door.
Wake function
Setting wake time
•
two blades and a third grounding
prong. The wide blade or the third
prong is provided for your safety. If
the provided plug does not fit into
your outlet, consult an electrician
for replacement of the obsolete
outlet.
Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
Only use attachments/accessories
specified by the manufacturer.
Use only with
the cart, stand,
]
tripod, bracket,
or table
specified by the
manufacturer,
Portable Cart Warning
or sold with
the apparatus.
When a cart is used, use caution
when moving the cart/apparatus
combination to avoid injury from
tip-over.
Unplug this apparatus during
lightning storms or when unused
for long periods of time.
Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as power-supply cord or plug is
damaged, liquid has been spilled
or objects have fallen into the
apparatus, the apparatus has been
Turning off the wake
alarm or radio
• To silence the wake function
momentarily:
To turn off the wake function, press
SNOOZE/SLEEP OFF on the top of
the unit. The wake alarm or radio
will be switched off temporarily.
The alarm or radio will be on again
when the snooze period (9 minutes)
is over.
Snooze function can be used
repeatedly up to 2 hours. After this,
the alarm will turn off until the
next alarm conditions are met.
• To turn off the wake alarm or
radio:
Press ALARM SET/OFF. The wake
alarm or radio will activate again
the next day unless you switch off
the Wake function.
• To disable the wake function
completely:
Slide ON/OFF/RADIO(WAKE)/
ALARM(WAKE) to OFF.
Power failure indicator
exposed to rain or moisture, does
not operate normally, or has been
dropped.
ADDITIONAL SAFETY INFORMATION
• Apparatus shall not be exposed to
dripping or splashing and no objects
filled with liquids, such as vases,
shall be placed on the apparatus.
• Always leave sufficient space around
the product for ventilation. Do
not place product in or on a bed,
rug, in a bookcase or cabinet that
may prevent air flow through vent
openings.
• Do not place lighted candles,
cigarettes, cigars, etc. on the
product.
• Connect power cord only to AC
power source as marked on the
product.
• Care should be taken so that objects
do not fall into the product.
• Do not attempt to disassemble
the cabinet. This product does
not contain customer serviceable
components.
• The marking information is located
at the bottom of apparatus.
• To be completely disconnect the
power input, the mains plug of
apparatus shall be disconnected
from the mains.
• Mains plug is a disconnect device.
The mains plug should not be
obstructed OR should be easily
accessed during intended use.
• The ventilation should not be
Ecology
Help protect the environment - we
recommend that you dispose of used
batteries by putting them into specially
designed receptacles.
Radio
Right view
Setting clock
Selecting radio mode
1. Press and hold TIME.
Slide ON/OFF/RADIO(WAKE)/
ALARM(WAKE) to ON to switch on
radio. Slide to OFF to switch off radio.
When AC power is interrupted
(disconnected) for a short period of
time, both time and alarm settings
will change (unless batteries are
installed). After AC power is restored
(reconnected), the Digital Display
will blink to indicate that power was
interrupted and you should re-adjust
the time and alarm settings.
• – VOLUME + – To adjust volume
• TUNING – To adjust radio frequency
Alkaline (NEDA 1604A/
IEC 6LR61) battery is
recommended. Carbon-zinc
battery may be used but memory
holding time will be substantially
reduced. Memory holding time
for a fresh alkaline battery is
approximately 8 hours (if radio
or alarm are not operated) which
should take care of short, nuisancetype AC power failures. To preserve
battery life, the unit should remain
plugged into an AC outlet. As the
battery gets older, its voltage drops
and memory may be lost. Be sure
to replace the battery periodically.
Battery should be removed if the
unit will be stored for more than
one month. Leaky battery can
badly damage the clock radio.
2. Press HRS or MIN to set the clock
time.
• AM indicator lights when the time is
set to AM.
• PM indicator lights when the time is
set to PM.
3. To save and exit the clock setting,
release TIME.
Top view
• ON/OFF/RADIO(WAKE)/
ALARM(WAKE) – To turn radio on
or off; to change wake mode (radio/
alarm)
• TIME – To adjust the clock time
• ALARM SET – To activate the wake
settings
• SLEEP – To activate sleep function
• AM/FM – To select radio band
• HRS – To adjust hour value when
setting clock, wake and sleep modes
• MIN – To adjust the minute value
when setting clock, wake and sleep
modes
• SNOOZE/SLEEP OFF – To quiet
the wake alarm or wake radio
temporarily (9 minutes); to cancel
sleep function
Switching band
Slide the band switch AM/FM to select
FM or AM band.
Tuning the radio
Rotate the TUNING knob on the
right of the unit to adjust the radio
frequency with reference to the tuning
dial scale.
Built-in AFC
The Built In Automatic Frequency
Control (AFC) works only on FM. It helps
reducing drift on FM reception and
keeping the radio locked in on the FM
station to which it is tuned.
When tuning in FM stations, you may
notice that the station you are tuning
can be well-tuned on two or three
nearby points on the dial. Always tune
carefully at the loudest and clearest
point.
AM antenna
A built-in ferrite rod antenna eliminates
the need for an outside antenna for
AM reception. Rotating the unit slightly
may improve reception of distant AM
stations.
Set sleep time manually
12 Month Limited Warranty
Applies to RCA Clock Radios
players, home networks or vehicle
electrical systems.
AUDIOVOX ACCESSORIES CORP. (the
Company) warrants to the original retail
purchaser of this product that should
this product or any part thereof, under
normal use and conditions, be proven
defective in material or workmanship
within 12 months from the date of
original purchase, such defect(s) will be
repaired or replaced with reconditioned
product (at the Company’s option)
without charge for parts and repair
labor.
This Warranty does not apply to any
product or part thereof which, in the
opinion of the Company, has suffered
or been damaged through alteration,
improper installation, mishandling,
misuse, neglect, accident, or by removal
or defacement of the factory serial
number/bar code label(s). THE EXTENT
OF THE COMPANY’S LIABILITY UNDER
THIS WARRANTY IS LIMITED TO THE
REPAIR OR REPLACEMENT PROVIDED
ABOVE AND, IN NO EVENT, SHALL THE
COMPANY’S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT.
To cancel the sleep mode:
• Press SNOOZE/SLEEP OFF to cancel
the sleep mode and turn off the
unit.
AC OUTLET POWER SUPPLY:
120 V ~ 60 Hz
The AC power plug is
polarized (one blade is
wider than the other)
and only fits into AC
power outlets one
way. If the plug will
not go into the outlet
completely, turn the plug over and try
to insert it the other way. If it still does
not fit, contact a qualified electrician
to change the outlet, or use a different
one. Do not attempt to bypass this
safety feature.
• Any battery may present a risk of
fire, explosion, or chemical burn
if abused. Do not try to charge a
battery that is not intended to be
recharged, do not incinerate, and
do not puncture.
• Non-rechargeable batteries, such as
alkaline batteries, may leak if left in
your product for a long period of
time. Remove the batteries from the
product if you are not going to use
it for a month or more.
• If your product uses more than one
battery, do not mix types and make
sure they are inserted correctly.
Mixing types or inserting incorrectly
may cause them to leak.
• Discard any leaky or deformed
battery immediately. They may
cause skin burns or other personal
injury.
• Please help to protect the
environment by recycling or
disposing of batteries according to
federal, state, and local regulations.
WARNING: The battery (battery or
batteries or battery pack) shall not
be exposed to excessive heat such as
sunshine, fire or the like.
Clock
Warranty information
To set the sleep mode:
1. Press and hold SLEEP and press
MIN simultaneously to adjust the
sleep time. The time range is from
from 0:01 to 1:59. (The default time
is 59 minutes.)
• The radio will be switched on.
Plugging in for power
Important battery
precautions
General controls
Sleep function
In sleep function, the unit will turn off
automatically after a specified time.
impeded by covering the ventilation
openings with items such as
newspaper, table-cloths, curtains etc.
• No naked flame sources, such as
lighted candled, should be placed
on the apparatus.
• Attention should be drawn to the
environmental aspects of battery
disposal.
• The use of apparatus in moderate
climates.
This is class II
equipment designed
with double or
reinforced insulation
so it does not require
a safety connection to
electrical earth (US:
ground).
To obtain repair or replacement
within the terms of this Warranty, the
product is to be delivered with proof
of warranty coverage (e.g. dated bill
of sale), specification of defect(s),
transportation prepaid, to the Company
at the address shown below.
This Warranty does not extend to the
elimination of externally generated
static or noise, to correction of
antenna problems, loss/interruptions of
broadcast or internet service, to costs
incurred for installation, removal or
reinstallation of product, to corruptions
caused by computer viruses, spyware or
other malware, to loss of media, files,
data or content, or to damage to tapes,
discs, removable memory devices or
cards, speakers, accessories, computers,
computer peripherals, other media
This Warranty is in lieu of all other
express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING
ANY IMPLIED WARRANTY OF
MERCHANTABILITY, SHALL BE LIMITED
TO THE DURATION OF THIS WRITTEN
WARRANTY. ANY ACTION FOR BREACH
OF ANY WARRANTY HEREUNDER
INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY MUST BE
BROUGHT WITHIN A PERIOD OF 24
MONTHS FROM DATE OF ORIGINAL
PURCHASE. IN NO CASE SHALL THE
COMPANY BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR
ANY OTHER WARRANTY. No person or
representative is authorized to assume
for the Company any liability other than
expressed herein in connection with the
sale of this product.
Some states do not allow limitations on
how long an implied warranty lasts or
the exclusion or limitation of incidental
or consequential damage so the above
limitations or exclusions may not apply
to you. This Warranty gives you specific
legal rights and you may also have
other rights which vary from state to
state.
Recommendations before returning
your product for a warranty claim:
• Properly pack your unit. Include
any remotes, memory cards, cables,
etc. which were originally provided
with the product. However DO NOT
return any removable batteries,
even if batteries were included
with the original purchase. We
recommend using the original
carton and packing materials. Ship
to the address shown below.
• Note that product will be returned
with factory default settings.
Consumer will be responsible to
restore any personal preference
settings.
Audiovox Electronics Corp.
Attn: Service Department.
150 Marcus Blvd.
Hauppauge N.Y. 11788
1-800-645-4994
For Canada Customers, please ship to:
Audiovox Return Centre
c/o Genco
6685 Kennedy Road,
Unit#3, Door 16,
Mississuaga, Ontario
L5T 3A5
Illustrations contained within this
publication are for representation only
and subject to change.
The descriptions and characteristics
given in this document are given as
a general indication and not as a
guarantee. In order to provide the
highest quality product possible,
we reserve the right to make any
improvement or modification without
prior notice.
Visit http://store.audiovox.com to find the best
accessories for your products.
© 2011 Audiovox Accessories Corporation
111 Congressional Blvd., Suite 350
Carmel, IN 46032
Trademark(s) ® Registered
Printed in China