PN-V601
LCD MONITOR
OPERATION GUIDE
Contents
Part Names........................................................................3
Basic Operation................................................................5
Remote Control Mode .....................................................7
Menu Items........................................................................8
Displaying the menu screen..........................................8
Menu item details..........................................................9
Adjustments for PC screen display.............................15
Initialization (Reset)/Functional Restriction Setting
(FUNCTION).....................................................................16
Controlling the Monitor with a PC (RS-232C)...............17
PC connection.............................................................17
Communication conditions..........................................17
Communication procedure..........................................17
Setting of the GAMMA user data.................................20
RS-232C command table............................................21
Controlling the Monitor with a PC (LAN)......................28
Settings to connect to a LAN.......................................28
Controlling with a PC...................................................30
Troubleshooting..............................................................36
Specifications.................................................................37
This guide contains instructions regarding operation, settings, and similar details.
For instructions regarding connection and installation, refer to the included Operation Manual.
Manual Scope
- Microsoft, Windows and Internet Explorer are registered trademarks of Microsoft Corporation.
- HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing
LLC.
- Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United
States and/or other countries.
- This product comes with RICOH Bitmap Fonts produced and sold by RICOH COMPANY, LTD.
- All other brand and product names are trademarks or registered trademarks of their respective holders.
- Language of OSD menu used in this manual is English by way of example.
- Illustrations in this manual may not exactly represent the actual product or display.
- This manual assumes use in horizontal orientation, except where specifically noted.
E
2
Part Names
nFront view
1
1. LCD panel
2. INPUT button
3. MENU button
4. VOL -/Cursor control ( ) button
5. VOL +/Cursor control ( ) button
6. BRIGHT -/Cursor control ( ) button
7. BRIGHT +/Cursor control ( ) button
8. Power button
9. Power LED
The rear buttons if seen
from the front
2
3
4
6
5
7
8
9
nRear view
10
11
12
13
14
15
16
17 18 19 20 21 23
22 24
When the PN-ZB02
(optional) is attached
25
26 27 28 29 30 31 33 34
32
9
8
7
6
5
4
3
2
Caution
• Consult your SHARP dealer for attachment/detachment of
optional parts.
• Do not open the expansion terminal cover by yourself.
There are high voltage parts inside the cover which may
cause an electric shock.
0. Fan
1
11. Vents
12. Handles
13. Expansion terminal cover
Additional input/output terminals are available by attaching
the PN-ZB02 interface expansion board (optional).
14. Optional attachment section
This section is used to connect optional hardware for
function expansion. Offering this attachment location
is not a guarantee that future compatible hardware
attachments will be released.
15. AC input terminal
16. Main power switch
17. PC/AV HDMI input terminal
18. PC D-sub input terminal
19. Audio input terminal
20. Audio output terminals
21. RS-232C output terminal
22. RS-232C input terminal
23. Optional terminal
This terminal is provided for possible future (optional)
function expansion. Offering of this terminal is not a
guarantee that future expanded functionality will be
provided.
24. Control kit terminal
When the PN-ZB02 (optional) is attached
25. PC/AV DVI-D input terminal
26. PC/AV DVI-D output terminal
27. LAN terminal
28. External speaker terminals
29. Audio 1 input terminals
30. Audio 2 input terminals
31. PC RGB input terminals
32. AV component input terminals
33. AV video input terminal
34. AV S-video input terminal
3
E
Part Names
Remote control unit
n
(Supplied with the PN-ZR01 (optional))
1
2
8
3
9
4
5
10
11
6
1. Signal transmitter
2. POWER button
3. MUTE button
4. VOL +/Cursor control ( ) button
5. BRIGHT -/Cursor control ( ) button
6. DISPLAY button
7. MODE button
8. INPUT button
9. MENU button
10. BRIGHT +/Cursor control ( ) button
11. VOL -/Cursor control ( ) button
12. SIZE button
12
7
Remote control sensor box
n
(Supplied with the PN-ZR01 (optional))
1
2
4
3
E
4
1.
2.
3.
4.
Brightness sensor
Remote control sensor
Connection cable
Mounting bracket
Basic Operation
When performing operation of multiple monitors with the
remote control unit, first set the remote control unit to the
appropriate remote control mode (see page 7).
1
2
2. MUTE
Turns off the volume temporarily.
Press the MUTE button again to turn the sound back to the
previous level.
If using the monitor buttons, either hold both
and
at the
same time or select MUTE AUDIO from the OPTION menu.
3. MENU
Displays and turns off the menu screen (see page 8).
3
4
4. VOL +/- (Volume adjustment)
5
Pressing
or
displays the VOLUME menu when the
menu screen is not displayed.
VOLUME
7
6
15
Press
or
to adjust the volume of the sound.
* If you do not press any buttons for about 4 seconds, the
VOLUME menu automatically disappears.
8
TIPS
• You can perform operation of the monitor with the rear
buttons. Utilize the buttons belonging to the monitor that
you would like to operate.
• Operation by using the buttons on the rear side of the
product will perform the same functions.
5. BRIGHT +/- (Backlight adjustment)
Pressing
or
displays the BRIGHT menu when the
menu screen is not displayed.
BRIGHT
15
Rear side buttons
Remote control
unit buttons
This manual assumes that this product will be used with
the remote control unit buttons, except where specifically
noted.
1. INPUT (Input mode selection)
The menu is displayed. Press
or
mode, and press
to enter.
Input mode
to select the input
Video
PC D-SUB
PC D-sub input terminal
PC HDMI
PC/AV HDMI input terminal*1
AV HDMI
PC/AV HDMI input terminal*1
Audio
Audio input terminal
*2
When the PN-ZB02 (optional) is attached
Input mode
Video
PC DVI-D
PC/AV DVI-D input terminal*3
PC HDMI
PC/AV HDMI input terminal*1
PC D-SUB
PC D-sub input terminal
PC RGB
PC RGB input terminals*4
AV DVI-D
PC/AV DVI-D input terminal*3
AV HDMI
PC/AV HDMI input terminal*1
Audio
*2
AV COMPONENT AV COMPONENT input terminals*4
AV S-VIDEO
AV S-video input terminal
AV VIDEO
AV video input terminal
*1 Select the terminal to be used in HDMI of INPUT SELECT.
(See page 11.)
*2 Select the terminal for AUDIO SELECT which is used for
audio input. (See page 11.)
*3 Select the terminal to be used in DVI of INPUT SELECT.
(See page 11.)
*4 Select the terminal to be used in BNC of INPUT SELECT.
(See page 11.)
Press
or
to adjust the brightness.
* If you do not press any buttons for about 4 seconds, the
BRIGHT menu automatically disappears.
* When BRIGHTNESS SENSOR is ON or ON: DISPLAY,
when the brightness is adjusted BRIGHTNESS SENSOR
will become OFF.
6. SIZE (Screen size selection)
The menu is displayed.
or
to select the screen size. (See page 6.)
Press
If using the monitor buttons, select SIZE from the OPTION
menu.
7. DISPLAY
Displays monitor information. When you press this button
again, the display disappears.
When the PN-ZB02 (optional) is attached, the display changes
from INFORMATION1 → INFORMATION2 → clear display,
and so on every time you press this button.
• The display disappears automatically after about 15
seconds.
• LAN is displayed during LAN communication.
• If LAN is displayed in red, there is a duplicate IP address.
under INFORMATION in
If using the monitor buttons, press
the OPTION menu.
8. MODE (Color mode selection)
Each time you press this button, the color mode changes in
the following order:
STD (Standard) → VIVID → sRGB → STD...
• sRGB applies to PC input only.
sRGB is international standard of color representation
specified by IEC (International Electrotechnical
Commission). Color conversion is made in taking account
of liquid crystal’s characteristics and represents color tone
close to its original image.
If using the monitor buttons, select COLOR MODE from the
PICTURE menu.
5
E
Basic Operation
nSwitching the screen size
Even when the screen size is changed, the display may remain the same depending on the input signal.
WIDE
ZOOM 1
PC input
Displays image so it fills the entire screen.
AV input
An image with a 4:3 aspect ratio is stretched to fill the entire
screen.
PC input
An image with a 4:3 aspect ratio is enlarged to fill the entire screen
without changing the aspect ratio. The edges of the image may be
cut off.
AV input
ZOOM 2
PC input
Use this size if ZOOM 1 cuts off the subtitles.
AV input
NORMAL
Dot by Dot
PC input
Displays image so it fills the screen without changing the aspect
ratio of the input signals.
AV input
Displays the entire image of the aspect ratio of 4:3 without
changing the aspect ratio.
PC input
Displays the dots of the signals input from the connected PC as
the corresponding dots on the screen.
AV input
Displays the dots of the input signals as the corresponding dots on
the screen.
TIPS
• Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial
or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright
Law, so please be careful.
• When “Enlarge” is set, the screen size is fixed to “WIDE” mode.
• When dual-screen display is selected, the screen size cannot be changed.
• The appearance of the original video may change if you select a screen size with a different aspect ratio than the original
image (e.g. TV broadcast or video input from external equipment).
• When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this
monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen
size to “NORMAL”.
• When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen
size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the
edges of the screen. This is due to the characteristics of the software, and is not a malfunction.
• Depending on the original image size, black bands may remain at the edges of the screen.
E
6
Remote Control Mode
With the remote control unit it’s possible to perform operation
of...
• The primary monitor
• Monitors with a specified ID No.
• All primary/secondary monitors
It’s necessary to specify which type of operation will be
performed in advance.
MODE
1. If using the remote control unit, press
seconds.
If using the monitor buttons, hold both
the same time on the primary.
for approx 5
and
at
ALL MONITORS
Performs operation of all primary/secondary monitors.
* ALL will be displayed on the menu of the primary.
* When it receives signals from the remote control unit,
“Operating all monitors.” will be displayed on the secondary
screen. (Excluding power and input mode selection operation)
* Settings may not be reflected depending on the state of the
connected monitors.
[Example] If the power for the primary is turned ON, the power
for all the monitors will be turned ON.
REMOTE CONTROL MODE
▲
THIS MONITOR ONLY
Operate this monitor.
OK
or
2. Press
settings.
CANCEL
, select the mode, then perform
Secondary
ID No.: 2
Primary
ID No.: 1
VOLUME 10
Secondary
ID No.: 3
Secondary
ID No.: 4
to lower the volume
SPECIFIED MONITOR
Performs operation of a monitor with a specified ID No. using
the remote control unit.
or
to select ID No., then press
or
to
Press
select the ID No. of the monitor that you will operate.
* When it receives signals from the remote control unit,
“Operating specified monitor.” will be displayed on the
primary screen.
[Example.] If ID No. is set to 3 and the volume is lowered,
the volume of the monitor for ID No.: 3 will lower.
Secondary
ID No.: 2
Secondary
ID No.: 4
Power ON
Primary
ID No.: 1
Secondary
ID No.: 4
POWER
to turn the power ON
Press
or
to select EXPAND ITEM, and press
or
to select to perform this action or not.
OFF�����������For all monitors, only power, input mode
selection, and product information display
operations will be recognized.
ON�������������For all monitors, all operations will be
recognized.
After returning to the normal screen with
procedure 3, when 5 minutes have passed from
the end of operation, it will automatically return
to OFF.
ALL [EXPAND ITEM]
will be displayed on the menu of
the primary.
* Even when REMOTE CONTROL MODE is set
to ALL MONITORS, certain settings such as
LAN settings and ID No. settings will not be
reflected on the other monitors.
3. Press
or
to select OK, then press
return to the normal screen.
MENU
and
4. Perform operation.
Caution
• When the remote control mode is set to ALL MONITORS
and EXPAND ITEM is set to ON, performing remote control
operations that change adjustment values will result in
the secondary adjustment values being the same as the
primary adjustment values.
Secondary
ID No.: 2
VOLUME 12
Primary
ID No.: 1
VOLUME 11
Secondary
ID No.: 2
VOLUME 10
Primary
ID No.: 1
VOLUME 10
Secondary
ID No.: 3
VOLUME 9
Secondary
ID No.: 4
VOLUME 10
Secondary
ID No.: 3
VOLUME 10
Secondary
ID No.: 4
VOLUME 10
Press
Secondary
ID No.: 3
Secondary
ID No.: 3
Power ON
Press
THIS MONITOR ONLY
Performs operation of only the primary using the remote
control unit.
[Example] If the volume is lowered, the volume of the primary
will lower.
Press
Primary
ID No.: 1
Power ON
▲
MODE
Secondary
ID No.: 2
Power ON
to lower the volume
Be careful of this when adjusting individual displays.
VOLUME 10
Press
to lower the volume
When you would like to confirm the ID No. that is set to the
monitor, press
or
to select ID No. DISPLAY, then
press
. The ID No. will be displayed on the screen.
TIPS
• You can copy the setting values of the primary to other
monitors with COPY SETTING VALUE. (See page 11.)
• The buttons on the monitor itself (primary) are also effective
in remote control mode.
• When monitors connected in a daisy chain are in standby
mode for LOW POWER, operation cannot be performed for
subsequent monitors.
7
E
Menu Items
Displaying the menu screen
TIPS
Video and audio adjustment and settings of various functions
are enabled. This section describes how to use the menu
items. See pages 9 to 12 for details of each menu items.
Caution
• Do not turn the main power switch off while the menu items
are being displayed. Doing so may initialize the settings.
nExample of operation
1. Press
SCREEN
1/1
AUTO
CLOCK
PHASE
H-POS
V-POS
H-SIZE
V-SIZE
H-RESOLUTION
V-RESOLUTION
RESET
PICTURE
AUDIO
SETUP
OPTION
MULTI
PIP/PbyP
1366x768
PC D-SUB
600
25
610
37
50
50
1366
768
V: 60 Hz
or
SCREEN
H: 47.7 kHz
CONTRAST
78
SETUP
BLACK LEVEL
84
OPTION
TINT
30
COLORS
30
SHARPNESS
12
MULTI
PIP/PbyP
1366x768
4. Press
or
SCREEN
88
SETUP
BLACK LEVEL
84
OPTION
TINT
30
COLORS
30
SHARPNESS
12
MULTI
PIP/PbyP
1366x768
For items that have
MENU
press
.
8
H: 47.7 kHz
PC D-SUB
1/2
CONTRAST
5. Press
OK···[MENU]
AUTO
AUDIO
MENU
V: 60 Hz
, press
78
BLACK LEVEL
84
OPTION
TINT
30
COLORS
30
SHARPNESS
12
V: 60 Hz
H: 47.7 kHz
OK···[MENU]
1 Name of the menu
2 Input mode
3 An item being selected (highlighted)
4 Screen resolution of input signal, and other data.
TIPS
nMenu Items
The displayed menu items vary depending on whether or not
the PN-ZB02 (optional) is attached.
The following menus will be displayed only when the PN-ZB02
(optional) is attached.
to adjust the setting.
PICTURE
PICTURE
E
V: 60 Hz
CONTRAST
• Items that cannot be selected appear in gray.
(e.g. Function not supported by the current input signal)
AUTO
AUDIO
PC D-SUB
.
PC D-SUB
1/2
1/2
4
AUTO
1366x768
to select CONTRAST.
PICTURE
PICTURE
PICTURE
2
SETUP
PIP/PbyP
END···[MENU]
3
AUDIO
MULTI
or
to select PICTURE, and press
2. Press
PICTURE menu is displayed.
3. Press
1
PICTURE
to display the menu screen.
SCREEN
nMenu screen display
SCREEN
(Adjusting CONTRAST in the PICTURE menu)
MENU
• The menu will differ depending on the input mode.
• The menu screen will close automatically if no operation is
performed for about 15 seconds. (DATE/TIME SETTING,
SCHEDULE and LAN SETUP screens will close in about 4
minutes.)
H: 47.7 kHz
OK···[MENU]
, make settings and then
twice to close the menu screen.
Menu
Item
PICTURE ADVANCED
3D-Y/C
SETUP
HOT PLUG CONTROL DVI
RS-232C/LAN SELECT
LAN SETUP
OPTION
INPUT SELECT
DVI
BNC
AUDIO SELECT
PC DVI-D
PC D-SUB
PC RGB
AV DVI-D
AV COMPONENT
AV S-VIDEO
AV VIDEO
PIP/PbyP PIP SOURCE
TIPS
• Some items may not be displayed depending on the input
mode.
Menu Items
Menu item details
The menu will differ depending on the input mode.
nSCREEN
AUTO (PC D-SUB/PC RGB)
The CLOCK, PHASE, H-POS, and V-POS are automatically
adjusted.
Pressing
performs adjustment.
Use this automatic adjustment when you use the PC D-sub
input terminal or PC RGB input terminals to display a PC
screen for the first time or when you change the setting of
the PC. (See page 15.)
CLOCK (PC D-SUB/PC RGB)
Adjusts frequency for sampling clock for applicable video.
Adjust when there is flickering in the form of vertical stripes.
When using the adjustment pattern (see page 15), make
adjustments so that no vertical stripe noise appears in it.
PHASE (PC D-SUB/PC RGB)
Adjusts sampling clock phase for applicable video.
Useful when small characters appear with low contrast and/
or there are flickers at corners.
When using the adjustment pattern (see page 15), make
adjustments so that no horizontal stripe noise appears in it.
* Adjustments to PHASE should be made only after CLOCK
has been correctly set.
H-POS
Adjust the horizontal position of the image.
V-POS
Adjust the vertical position of the image.
H-SIZE
Adjust the horizontal size of the image.
V-SIZE
Adjust the vertical size of the image.
H-RESOLUTION (PC D-SUB/PC RGB)
Sets proper horizontal resolution when the resolution of
input signals is not recognized properly. (Adjustment may be
impossible with some signals.)
V-RESOLUTION (PC D-SUB/PC RGB)
Sets proper vertical resolution when the resolution of input
signals is not recognized properly. (Adjustment may be
impossible with some signals.)
RESET
Resets the values of the SCREEN menu items to the factory
preset values.
MENU
Select “ON” and then press
.
nPICTURE
AUTO (PC D-SUB/PC RGB)
The CONTRAST and BLACK LEVEL are automatically
adjusted.
Pressing
performs adjustment.
CONTRAST
Adjusts the brightness of the image.
BLACK LEVEL
Adjusts the entire brightness of the video signals.
TINT
Adjusts the hue. Selecting + changes the color towards
green, and selecting - changes it towards magenta.
COLORS
Adjusts the color intensity.
SHARPNESS
Adjusts the sharpness of the image.
ADVANCED (AV input)
You can adjust more specifically. (See page 15.)
COLOR MODE
Changes the color mode on the screen. The color mode on
the screen can also be changed using a remote control unit.
(See page 5.)
* sRGB is PC input only. See page 5 for details.
WHITE BALANCE
THRU�������������� Displays the input signal level as is. (for PC
DVI-D/PC HDMI only)
PRESET��������� Selects the color temperature using PRESET.
USER�������������� Used for adjusting R-/G-/B-CONTRAST and
R-/G-/B-OFFSET respectively.
PRESET
Selects the color temperature when the WHITE BALANCE is
set to PRESET.
The setting values are shown for reference. The color
temperature of the screen varies over time.
This function is not intended to keep the color temperature
constant.
USER
Adjusts each item when the WHITE BALANCE is set to
USER.
R-CONTRAST.....Adjusts bright-toned red component.
G-CONTRAST.....Adjusts bright-toned green component.
B-CONTRAST.....Adjusts bright-toned blue component.
R-OFFSET...........Adjusts dark-toned red component.
G-OFFSET..........Adjusts dark-toned green component.
B-OFFSET...........Adjusts dark-toned blue component.
COPY TO USER
Copies the value set for PRESET to the USER setting.
MENU
.
Select “ON” and then press
GAMMA
Select a gamma value. USER sets the gamma value
transferred by the user. (See page 20.)
RESET
Resets the values of the PICTURE menu items to the factory
preset values.
MENU
.
Select “ON” and then press
9
E
Menu Items
nAUDIO
TREBLE
Adjusts the volume of treble-level sound.
BASS
Adjusts the volume of bass-level sound.
BALANCE
Adjusts the balance of the audio sound between right and left.
RESET
Resets the values of the AUDIO menu items to the factory preset values.
MENU
Select “ON” and then press
.
nSETUP
OSD H-POSITION
Adjusts the horizontal display position of menu screen.
OSD V-POSITION
Adjusts the vertical display position of menu screen.
SCREEN MOTION
Residual images are reduced by moving the screen.
PATTERN1����� The whole screen moves vertically and
horizontally.
PATTERN2����� A black screen spreads from the bottom of
the screen and then shrinks to the bottom of
the screen.
If the monitor is installed in the vertical
orientation, a black screen spreads from the
left end of the screen and then shrinks to the
left end of the screen.
PATTERN3����� A black bar moves from the left end to the
right end of the screen.
If the monitor is installed in the vertical
orientation, a black bar moves from the top
to the bottom of the screen.
PATTERN4����� Black screens appear from both the top and
bottom of the screen, and the displayed
image is compressed into the central field.
If the monitor is installed in the vertical
orientation, the screen is compressed from
the left and right ends.
PATTERN1
PATTERN2
PATTERN3
PATTERN4
MOTION TIME 1
Specify a time period (operating interval) until SCREEN
MOTION starts.
MOTION TIME 2
Specify a time period during which SCREEN MOTION
operates (time period during which the screen will move).
MONITOR
Select the installation direction of the monitor.
LANDSCAPE.............Horizontal orientation
PORTRAIT................Vertical orientation
LANGUAGE
Sets the display language for the menu screen.
E
10
POWER ON DELAY
You can delay the screen display after the monitor is turned
on. The period can be set up to 60 seconds in units of one
second. When this function is activated, the power LED
flashes (at approx. 1 second interval) in orange. This function
is disabled when 0 is specified.
STANDBY MODE
When STANDARD is selected, startup time from standby
mode is reduced. Note, however that, more power will be
consumed in standby mode.
When LOW POWER is selected, current consumption
is reduced while the monitor is in standby mode. Note,
however, that the startup time from standby mode becomes
longer.
If set to LOW POWER, certain RS-232C commands cannot
be used in standby mode, and control via LAN will be
disabled.
OFF IF NO OPERATION
Determines whether or not to set the monitor to go into
standby mode when there is no operation from the remote
control unit, RS-232C commands, or LAN for over 4 hours.
HDMI SETTING
HDMI AUTO VIEW
..........................When ON is selected, the screen size is
adjusted automatically according to the
screen size control signal included in the
video signal input from the AV HDMI input
terminal.
HDMI RGB INPUT RANGE
..........................Sets the type of HDMI signals when using
the AV HDMI input mode.
When AUTO is selected, the type is set
automatically.
HOT PLUG CONTROL
Sets whether to use hot plug control for the PC/AV HDMI
and PC/AV DVI-D input terminals.
RS-232C/LAN SELECT
Selects the method with which to control the monitor from
the computer.
ID No. SET
Assigns ID numbers to monitors connected in a daisy chain
(see page 18), using the remote control unit or RS-232
cables.
The numbers 1 to 255 are available for ID numbers.
If “0” is set, the system regards this as the state where no ID
number is set.
AUTO ASSIGN ID No.
ID No. to be used will be automatically assigned when
multiple monitors are connected with RS-232C.
MENU
Select ON, then press
. Perform operations with the
primary monitor.
BAUD RATE
Selects the communication speed used for RS-232C
communication.
LAN SETUP
Configures the settings to control the monitor from the
computer via LAN. (See page 28.)
Menu Items
BRIGHTNESS SENSOR
(When connected to the PN-ZR01 only)
When set to ON or ON: DISPLAY, the brightness will
automatically change according to the lighting and
surrounding brightness. Performs operation with the primary
monitor. If set to ON: DISPLAY, the effect will be displayed
with a
.
If connecting to multiple monitors, the brightness of all the
monitors will change.
The
will be displayed on the primary only.
BRIGHTNESS SENSOR SETTING
(When connected to the PN-ZR01 only)
Performs adjustments to the brightness sensor. Performs
operation with the primary monitor.
Set the surrounding brightness and the current screen
luminance to AMBIENT BRIGHTNESS and SCREEN
BRIGHTNESS.
Individually set WHEN LIGHT: and WHEN DARK:.
Even if brighter or darker than the set AMBIENT
BRIGHTNESS, the screen brightness will not change.
Current AMBIENT BRIGHTNESS is shown for reference.
COPY SETTING VALUE
When the monitor has been connected to multiple monitors
with RS-232C, you can copy the primary setting details to
the secondary. Perform operations with the primary monitor.
Select the ID No. of the monitor that you would like copy to
MENU
.
with COPY TO ID No., then select COPY and press
If you select ALL, settings will be copied to all monitors.
When you would like to confirm the ID No. that is set to the
monitor, select ID No. and press
. The ID No. will be
displayed on the screen.
nOPTION
DATE/TIME SETTING
to select the date
or
Set the date and time. Press
and time, and press
or
to change the numerical
values.
Set the date in “Year/Month/Day” order.
Set the time on a 24-hour basis.
SCHEDULE (See page 14.)
You can set the time to switch the monitor on and off.
INPUT SELECT
Select the input mode to be used in PC/AV DVI-D input
terminal, PC/AV HDMI input terminal and PC RGB/AV
component input terminals.
AUDIO SELECT
Selects the terminal used to input audio signals in each input mode.
INPUT SIGNAL (PC D-SUB/PC RGB)
If a computer connected to the PC D-sub/PC RGB input
terminal outputs any of the following resolutions, make a
selection from the following options.
480 LINES...........AUTO, 640x480 or 848x480
768 LINES...........AUTO, 1024x768, 1280x768, 1360x768 or
1366x768
1050 LINES.........1400x1050 or 1680x1050
ZOOM2 SPECIAL SETTING (See page 13.)
SCAN MODE (AV input)
Sets the scan mode used for AV mode input.
MODE1................Over-scan display
MODE2................Under-scan display
MODE3................Under-scan display when the input signal
is 1080i/p. Otherwise, over-scan display
POWER MANAGEMENT
POWER MANAGEMENT determines whether or not to
switch modes from no signal to the input signal standby
mode.
COLOR SYSTEM (AV S-VIDEO/AV VIDEO)
Select the color system of the AV equipment which is
connected to AV S-video and AV video input terminal. (AUTO
/ PAL / PAL-60 / SECAM / NTSC3.58 / NTSC4.43)
When AUTO is selected, the color system is automatically
set according to the input signal.
AUDIO OUTPUT(RCA)
Sets the volume of sound output from the audio output
terminals. When set to VARIABLE2, audio is not output from
the external speaker terminals.
VARIABLE...........You can adjust the volume using VOLUME.
FIXED..................Disables volume adjustment and fixes the
sounds.
When the PN-ZB02 (optional) is attached:
VARIABLE1.........You can adjust the volume using VOLUME.
VARIABLE2.........You can adjust the volume using VOLUME,
but audio is not output from the external
speaker terminals.
FIXED..................Disables volume adjustment and fixes the
sounds.
AUDIO LEVEL(STEREO MINI)
Selects the maximum audio input level of the audio input
terminal.
SELF ADJUST
On a PC D-SUB/PC RGB screen, specify whether to
perform screen adjustment automatically or not. When ON
is selected, the screen is automatically adjusted when its
resolution is 800 x 600 or higher and the timing of input
signals changes. “ADJUSTING” appears on the screen
during the adjustment. For images with black edges, etc.,
depending on the signal, adjustment may not be possible.
In this case select OFF. (Perform manual adjustment of the
screen.)
AUTO INPUT CHANGE
Specify whether to change inputs automatically. When ON is
selected and no signal is present in the selected input mode,
AUTO INPUT CHANGE automatically changes the selected
mode to another mode where a video signal is present.
When video signals exist in multiple input modes, the
switching priority is as follows:
PC D-SUB, PC HDMI and AV HDMI
When the PN-ZB02 (optional) is attached:
PC DVI-D, PC HDMI, PC D-SUB, PC RGB, AV DVI-D, AV
HDMI, AV COMPONENT, AV S-VIDEO and AV VIDEO
(Input mode switching may take 15 seconds or more,
depending on the connected equipment. Input signals
may not be detected properly and a priority may change,
depending on the connected equipment or video signals.)
FAN SPEED
Sets the rotation speed of the fan.
As this number increases, the rotation speed becomes
faster. When set to AUTO, the rotation speed of the fan will
change depending on the internal temperature.
SIZE
Selects screen size. (See page 6.)
MUTE AUDIO
Can temporarily turn off the volume.
INFORMATION
If you press
, monitor information can be checked.
11
E
Menu Items
nMULTI
ENLARGE (See page 13.)
Sets whether or not to use the enlarge function.
ADVANCED (ENLARGE)
ENLARGE H / ENLARGE V
.......... Sets the number of screen splits (number of
monitors) in the horizontal/vertical direction used for
the enlargement.
ENLARGE-POS
.......... Specify the split screen to be displayed when the
enlargement function is used.
H-POS / V-POS
.......... Adjust the horizontal/vertical position of the enlarged
screen.
BEZEL ADJUST
Sets whether or not to use the frame correction function.
ADVANCED (BEZEL ADJUST)
BEZEL ADJUST (TOP) / BEZEL ADJUST (BOTTOM) /
BEZEL ADJUST (RIGHT) / BEZEL ADJUST (LEFT)
.......... Adjusts so that the top/bottom/left/right connecting
joints of grouped units will be displayed smoothly
when a group of monitors are aligned in multiples to
display a single image.
BEZEL H / BEZEL V
.......... Sets the frame width of the display.
TIPS
• When WHITE BALANCE is set to THRU, BLACK LEVEL,
CONTRAST, TINT, COLORS and GAMMA cannot be set.
• If COLOR MODE is set to sRGB, the following items cannot
be set.
WHITE BALANCE, PRESET, USER, COPY TO USER, and
GAMMA
• When the COLOR MODE is set to VIVID, GAMMA can not
be adjusted.
• If GAMMA is set to USER, the following items cannot be
set.
WHITE BALANCE, PRESET, USER, and COPY TO USER
• STANDBY MODE cannot be set to LOW POWER when
SCHEDULE is effective or when OFF is selected for LED in
FUNCTION.
nDual screen display
You can display the screens of the PC input signal and AV
input signal simultaneously.
Set this function with “PIP MODES” in the PIP/PbyP menu.
PIP
Sub
screen
PbyP
nPIP/PbyP
PIP MODES
Sets the display method.
OFF���������Displays one screen.
PIP�����������Displays a sub screen inside a main screen.
PbyP��������Displays a main screen and a sub screen in a line.
PbyP2������Displays a main screen which measures 1024 pixels
in the longest direction and a sub screen in a line.
PIP SIZE
Sets the size of the sub screen in PIP mode.
PIP H-POS
Adjusts the horizontal position of the sub screen in PIP mode.
PIP V-POS
Adjusts the vertical position of the sub screen in PIP mode.
PIP BLEND
In PIP mode, use this menu item to display the sub screen
transparently.
PIP SOURCE
Selects the input signal of the sub screen in PIP, PbyP, or
PbyP2 mode.
SOUND CHANGE
Sets the sound which is output in PIP, PbyP, or PbyP2 mode.
If the main screen is displayed as a full screen by the AUTO
OFF function, the sound for the main screen is output even
when the sound for the sub screen is specified.
MAIN POS
Sets the position of the main screen in PbyP or PbyP2 mode.
PbyP2 POS
Sets the position of the sub screen in PbyP2 mode.
AUTO OFF
Sets the display method when no signals for the sub screen
are input in PIP, PbyP, or PbyP2 mode.
MANUAL........ Displays a main screen and a black sub screen.
AUTO............. Displays the main screen as a full screen.
E
12
A sub screen is displayed
inside a main screen.
Main screen
Main
screen
Sub
screen
PbyP2
Main screen
Sub
screen
A main screen and a sub
screen are displayed in a
line.
Displays a main screen
which measures 1024
pixels in the longest
direction and a sub
screen in a line.
* The currently selected input signal is displayed on the main
screen.
* You cannot simultaneously display the screens of signals
of the same type, such as two types of PC input signals or
two types of AV input signals.
* The dual screen display cannot be used with the
combination of PC DVI-D and AV HDMI or of AV DVI-D and
PC HDMI.
TIPS
• You might infringe on a copyright of the author which is
protected by copyright law when you display the images of
the computer screen and television/VCR simultaneously for
profit-making or to show the image to the public.
• The screen size for dual-screen display is the same as
the screen size for single-screen display. The Dot by Dot
screen is displayed in NORMAL size except when it is set
as the PIP main screen.
• When dual-screen display is selected, the SCREEN
MOTION function is disabled.
• When dual-screen display is selected, the AUTO INPUT
CHANGE function is disabled.
• When dual-screen display is selected, the screen cannot
be enlarged.
• When dual-screen display is selected, the INPUT SELECT
options cannot be set.
Menu Items
nEnlarge
nZOOM2 SPECIAL SETTING
• You can align several monitors and integrate them into a
single large screen to display.
• Up to five monitors can be aligned in both the horizontal
and vertical directions.
• Each monitor displays enlarged views of separated images.
If you connect a laptop computer with any of the following
screen resolutions and black bands appear around the
screen, set ZOOM2 SPECIAL SETTING of INPUT SIGNAL on
the OPTION menu to ON and then select ZOOM2 in the SIZE
setting.
This displays the area inside the black band.
(Example)
Horizontal direction: 2 monitors
Vertical direction: 2 monitors
Horizontal direction: 3 monitors
Vertical direction: 2 monitors
Laptop computer
resolution
Corresponding signal*1
1280x800
1280x1024, 1280x960, 1400x1050*2
1280x600
1280x720
1024x600
1024x768
*1: This setting is effective only when the screen resolution,
including the black band, is one of the resolutions listed
above.
*2: U
se the automatic screen adjustment.
Setting procedure
Set using the MULTI menu.
1. Set ENLARGE to ON.
2. Select ADVANCED (ENLARGE).
3. Set the number of monitors aligned in the horizontal
direction in ENLARGE H.
4. Set the number of monitors aligned in the vertical
direction in ENLARGE V.
5. Set the section of the separated image to be displayed
on each monitor in ENLARGE-POS.
1) Press
.
2) Press
,
,
or
to select position, then
MENU
press
.
TIPS
• When Enlarge is used, the SCREEN MOTION function is
disabled.
• When Enlarge is used, the AUTO INPUT CHANGE function
is disabled.
• When Enlarge is used, the HDMI AUTO VIEW function is
disabled.
13
E
Menu Items
nSCHEDULE
Caution
You can set the time to switch the monitor on and off.
Set this function with “SCHEDULE” in the OPTION menu. (See
page 11.)
PC D-SUB
SCHEDULE
XXXX/XX/XX XXX XX:XX:XX
No.
(1)
POWER (2)
DAY OF THE WEEK (3)
TIME (4)
INPUT (5)
• Do not switch off the main power after setting the
SCHEDULE.
• Specify the correct date and time. (See page 11.)
SCHEDULE does not function unless the date and time are
specified.
• Check regularly that the set date and time are correct.
• When STANDBY MODE is LOW POWER, SCHEDULE
cannot be set.
TIPS
1366x768
V: 60 Hz
H: 47.7 kHz
• Up to 8 SCHEDULE items can be registered.
• Setting the SCHEDULE flashes the power LED alternately
in red and orange in standby mode.
• A SCHEDULE that has a large number has precedence
over that of a small number when schedules overlap.
OK…[MENU]
1. Press
or
to select the SCHEDULE number, and
press
.
2. Set the SCHEDULE. (See the description below.)
or
to select items, and press
Press
change the setting.
or
to
MENU
3. Press
.
SCHEDULE becomes effective.
(1)
●: SCHEDULE effective
-: SCHEDULE not effective
(2) POWER
ON : Switches the monitor on at the specified time.
OFF: Switches the monitor off at the specified time and puts
the monitor in standby mode.
(3) DAY OF THE WEEK
Specifies the day of the week to execute the SCHEDULE.
ONLY ONCE:
Executes the SCHEDULE once on the specified day.
Specify the day of the week to execute the SCHEDULE.
EVERY WEEK:
Executes the SCHEDULE on the specified day of the week
every week. Specify the day of the week to execute the
SCHEDULE.
Periodic setting such as “Monday through Friday” is also
possible.
EVERY DAY:
Executes the SCHEDULE every day regardless of the day
of the week.
(4) TIME
Specifies the time to execute the SCHEDULE.
Set the time on a 24-hour basis.
(5) INPUT
Specifies the input mode at power-on. When not specifying,
the screen at the previous power-off appears.
Input modes displayed on DVI, HDMI and BNC depend on
INPUT SELECT settings.
E
14
Menu Items
nADVANCED items (AV input) (See page 9
for additional Menu item details.)
FLESH TONE
Adjust the hue control.
3D-NR
Reduce the noise of playback images on video.
Setting a higher level reduces more noise. However, it may
cause blurring on an image.
MPEG-NR
Reduce block noise caused by digital compression.
3D-Y/C (AV VIDEO)
Specify whether to perform 3-dimension Y/C separation.
If dot interference or cross-color is occurring in fast-motion
scenes, selecting “OFF” may improve the image quality.
C.M.S.-HUE
Adjusts color tone with 6 colors of R (red), Y (yellow), G
(green), C (cyan), B (blue), and M (magenta).
C.M.S.-SATURATION
Adjusts color vividness with 6 colors of R (red), Y (yellow), G
(green), C (cyan), B (blue), and M (magenta).
C.M.S.-VALUE
Adjusts color brightness with 6 colors of R (red), Y (yellow),
G (green), C (cyan), B (blue), and M (magenta).
TIPS
• When FLESH TONE is set to LOW or HIGH, C.M.S.-HUE/
-SATURATION/-VALUE cannot be set.
Adjustments for PC screen display
nAutomatic adjustment
When you use the PC D-sub input terminal or PC RGB input
terminals to display a PC screen for the first time, or when
you change the setting of the PC, use the automatic screen
adjustment.
1. Switch the input to PC D-SUB or to PC RGB and display
the adjustment pattern. (See the description below.)
MENU
2. Press
and use
or
to display the SCREEN
menu.
3. Press
and select “AUTO”.
.
4. Press
The automatic adjustment is complete in several seconds.
5. Press MENU twice to close the menu screen.
TIPS
• If the screen cannot be adjusted properly with one
automatic adjustment, repeat the automatic adjustment two
or three times. Try manual adjustment if necessary.
nScreen display for adjustment
Before making adjustments in the SCREEN menu or
PICTURE menu, display an image to brighten the entire
screen. If you are using a Windows PC, use the adjustment
pattern on the supplied CD-ROM.
Opening the adjustment pattern
The following example is performed in Windows 7.
1. Load the supplied CD-ROM into the computer’s CDROM drive.
2. Open [CD Drive] in [Computer].
In Windows XP, open [CD Drive] in [My Computer].
3. Double-click [Adj_uty.exe].
The adjustment pattern will appear.
Adjust the screen automatically or manually.
4. When adjustment is finished, press the [Esc] on the
computer’s keyboard to quit the adjustment program.
5. Eject the CD-ROM from the CD-ROM drive.
TIPS
• If the display mode on the computer you are using is
65,000 colors, the color levels in the color pattern may
appear differently or grayscale may appear to be colored.
(This is due to the specifications of the input signal and is
not a malfunction.)
15
E
Initialization (Reset)/Functional Restriction Setting (FUNCTION)
You can return the settings to their factory-preset values and
restrict operations.
SIZE
until “F”
1. If using the remote control unit, press
is displayed in the upper left area of the screen, then
,
,
, and
while “F” is being displayed, press
in that order.
and
at the
If using the monitor buttons, press
same time until “F” is displayed in the upper left area
of the screen, then while “F” is being displayed, press
and
at the same time.
FUNCTION
1/1
ALL RESET
ADJUSTMENT LOCK
RS-232C
OSD DISPLAY
OFF
UNLOCKED
ON
LED
ON
TEMPERATURE ALERT
LED
STATUS ALERT
OFF
END…[MENU]
2. Select and set the items.
ALL RESET
Resets the settings to the factory default settings.
MENU
, select ALL RESET, and then press
.
Press
After initialization, turn the main power switch off and
then back on.
When the PN-ZB02 (optional) is attached, press
,
MENU
.
select the resetting method, and then press
ALL RESET1����Resets all the settings to the factory
default settings.
ALL RESET2����Returns all settings to the factory default
settings except for the following items:
LAN SETUP, RS-232C/LAN SELECT,
ID No. SET, BAUD RATE, NETWORK,
MAIL, SERVICE & SUPPORT, and
SNMP (See page 10, and pages 32 to
35.)
ADJUSTMENT LOCK
You can disable operations on the monitor and the
remote control unit that use buttons.
OFF���Enables operation.
1��������Disables all operations other than turning power
on/off, FUNCTION, and REMOTE CONTROL
MODE.
2��������Only the FUNCTION and REMOTE CONTROL
MODE operations are enabled.
Disables all operations other than FUNCTION
and REMOTE CONTROL MODE (not even power
on/off).
RS-232C
(RS-232C/LAN when the PN-ZB02 (optional) is
attached)
Specifies whether to allow control via RS-232C or LAN
(see pages 17 and 28).
OSD DISPLAY
Hides/shows menus.
The FUNCTION and REMOTE CONTROL MODE
screens cannot be hidden.
E
16
LED
Specifies whether to light the power LED.
OFF cannot be selected when STANDBY MODE is LOW
POWER.
TEMPERATURE ALERT
Selects the notification method for an abnormal
temperature.
OFF�������������� Do not notify about an abnormal
temperature.
OSD & LED�� When an abnormal temperature is
detected, the power LED flashes in red
and green alternately and the screen
displays a message: TEMPERATURE.
LED�������������� When an abnormal temperature is
detected, the power LED flashes in red
and green alternately.
STATUS ALERT
Selects the notification method for a hardware error.
OFF�������������� Do not notify about the error.
OSD & LED�� When a hardware error is detected, the
power LED flashes in red and the screen
displays a message: STATUS [xxxx].
LED�������������� When a hardware error is detected, the
power LED flashes in red.
3. Press
MENU
to return to the normal screen.
TIPS
• When both abnormal temperature and hardware error are
detected, the hardware error notification overrides.
Controlling the Monitor with a PC (RS-232C)
You can control this monitor from a PC via RS-232C (COM
port) on the PC.
You can also connect multiple monitors via a daisy chain by
using a PC. By assigning ID numbers to each monitor (see
page 18), you can make input mode selection/adjustment or
can check the status of a specific monitor.
Precautions when the PN-ZB02 (optional) is attached
• To control the monitor via RS-232C, set RS-232C/LAN
SELECT to RS-232C.
• You cannot use RS-232C and LAN control simultaneously.
PC connection
nOne-to-one connection with a PC
Connect with RS-232 straight cable between the PC’s COM
port (RS-232C connector) and the RS-232C input terminal on
the monitor.
Communication conditions
Set the RS-232C communication settings on the PC to match
the monitor’s communication settings as follows:
Baud rate
*
Stop bit
1 bit
Data length
8 bits
Flow control
None
Parity bit
None
* Set to the same baud rate as the BAUD RATE setting of
SETUP menu. (Initial setting: 38400 bps)
* When connecting multiple monitors in a daisy chain, set all
monitors to the same BAUD RATE.
Communication procedure
nCommand format
When a command is sent from the PC to the monitor, the
monitor operates according to the received command and
sends a response message to the PC.
Return code
C1
RS-232C input terminal
C2
C3
C4
P1
Command field
(4 prescribed
alphanumerical characters)
P2
P3
P4
Parameter field
(4 character string comprised of:
0-9, +, -, space, ?)
PC
To COM port
RS-232 straight cable
(commercially available)
nDaisy chain connection… Advanced operation
Connect with RS-232 straight cable between the PC’s COM
port (RS-232C connector) and the RS-232C input terminal on
the first monitor.
Next, connect RS-232 straight cable to the first monitor’s
RS‑232C output terminal and to the second monitor’s
RS-232C input terminal. Connect in the same way to the third
and subsequent monitors.
Up to 25 monitors can be connected. (Depending on the
length of the cable used and the surrounding environment.)
First monitor
Second monitor
Example: VOLM0030
VOLM
30
* Be sure to input 4 characters for the parameter. Pad with
spaces (“ ”) if necessary.
(“
” is a return code (0DH, 0AH or 0DH))
Wrong : VOLM30
Right : VOLM
30
When inputting a negative value, specify a numerical value in
three digits.
Example: AUTR-009
Do not use spaces for MPOS, DATE, and SC01 through
SC08. Specify parameters using a specified number of
characters.
Example: MPOS010097
If a command has “R” listed for “DIRECTION” in the
“RS-232C command table” on page 21, the current value can
be returned by using “?” as the parameter.
RS-232C
output terminal
Example:
RS-232C
input terminal
VOLM ? ? ? ?
←
From PC to monitor (How much
is current volume setting?).
30
←
From monitor to PC (Current
volume setting: 30).
* If an ID number (see page 18) has been assigned
(For example, ID number = 1).
PC
VOLM
To COM port
RS-232 straight cables
(commercially available)
30
001
?
← From PC to monitor.
← From monitor to PC.
17
E
Controlling the Monitor with a PC (RS-232C)
nResponse code format
nCommunication interval
When a command has been executed correctly
• After OK or ERR is returned, you must send the following
commands.
To set a timeout for the command response, specify 10
seconds or longer.
When connecting multiple monitors in a daisy chain, set the
timeout to at least the product of the monitor’s position from
the computer multiplied by 10 seconds.
Example) 3rd monitor from computer: 30 seconds or longer.
• Provide an interval of 100 ms or more between the
command response and the transmission of the next
command.
VOLM0020
OK
O
K
Return code
(0DH, 0AH)
A response is returned after a command is executed.
* If an ID number has been assigned
Return code
(0DH, 0AH)
Space (20H)
O
K
SPC
0
0
1
ID number of responding monitor
When a command has not been executed
E
R
R
Interval of 100 ms or more
Return code
(0DH, 0AH)
INPS0001
WAIT
OK
* If an ID number has been assigned
Return code
(0DH, 0AH)
Space (20H)
E
R
R
SPC
0
0
1
TIPS
ID number
TIPS
• “ERR” is returned when there is no relevant command or
when the command cannot be used in the current state of
the monitor.
• If communication has not been established for reasons
such as a bad connection between the PC and monitor,
nothing is returned (not even ERR).
• If no monitor has been assigned the designated ID number
(e.g. if the command IDSL0002
is used, but no monitor
with ID number: 2 is found), no response is returned.
If execution of the command is taking some time
W
A
I
T
Return code
(0DH, 0AH)
When the following commands are used, “WAIT” is returned.
In this case, a value will be returned if you wait a while. Do not
send any command during this period.
No ID number is attached to WAIT response.
• Commands which return WAIT:
1. When repeater control is used
2. When an IDSL or IDLK command is used
3. When one of the following commands is used: RSET,
INPS, ASNC, WIDE, EMAG, EPOS, PXSL, POWR,
AGIN, MWIN, MWIP, MWPP, ESTG, EMHV, EPHV,
ESHV
When control via RS-232C is locked (to prevent use)
using the operation lock function (see page 16)
L
O
C
K
E
D
Return code
(0DH, 0AH)
• When executing ALL RESET, set the timeout period to 30
seconds or longer.
• When turning the power on while the POWER ON DELAY
function is in use, set the timeout period to the POWER ON
DELAY period + 10 seconds or longer.
Advanced operation
This section explains commands for daisy chain connection.
The basic communication procedure is the same as in the
“One-to-one connection with a PC” section.
nID numbers
You can assign a unique ID number to each monitor (see
page 10). This allows you to control a particular monitor in a
daisy chain of monitors.
You can assign ID numbers either from the menu screen (using
the remote control) or from the PC using RS-232 cable.
[Example]
ID number: 1
U
N
S
E
L
E
C
T
E
D
Return code
(0DH, 0AH)
E
18
ID number: 3
ID number: 4
If monitors are connected as shown above, you can
execute commands like “Set the volume of the monitor with
ID 4 to 20”.
When designating ID numbers for a set of monitors linked in a
daisy chain, you should basically avoid any duplication of ID
numbers.
ID numbers do not have to be assigned in ascending order
starting from the PC. They can also be connected as shown
below.
[Example]
ID number: 3
When RS-232C/LAN SELECT is set to LAN
ID number: 2
ID number: 2
ID number: 4
ID number: 1
Controlling the Monitor with a PC (RS-232C)
nCommands for ID control
The command examples shown on this page assume the
following connection and ID number set up.
ID number: 1
ID number: 2
ID number: 3
ID number: 4
IDST��������.A monitor receiving this command sets its own ID
number in the parameter field.
Example:
IDST0001
001 ← The ID number of this monitor is set to 1.
OK
IDLK��������The parameter of this command sets the ID
number of the monitor. The monitor is subject to all
subsequent commands.
Example:
← with ID number: 2.
WAIT
←
OK
002
Searching for monitor with ID number:
2
← Found monitor with ID number: 2
Sets volume of monitor with ID
VOLM0030
← number: 2 to 30.*
WAIT
← Processing
OK
002
VOLM0020
TIPS
Following commands are for the monitor
IDLK0002
Sets volume of monitor with ID
← number: 2 to 20.*
WAIT
You can automatically assign ID numbers by using the IDST
command with the Repeater control (see “Repeater control”
on page 20).
For example, using the command “IDST001+” automatically
sets the ID numbers, as shown below.
[Example]
ID number: 1
ID number: 2
ID number: 3
ID number: 4
OK
002
IDLK0000
← Canceling fixed ID number setting
WAIT
← Canceling IDLK
OK
002
← Cancelation complete
VOLM0010
The volume of the monitor with ID number:
OK
001
← 1 (the one directly connected to the PC) is
set to 10. (IDLK is canceled.)
IDST001 +
← ID setting command with repeater control
WAIT
OK
001
← “OK” response from ID number: 1
OK
002
← “OK” response from ID number: 2
OK
003
← “OK” response from ID number: 3
OK
004
← “OK” response from ID number: 4 (End)
IDSL��������The parameter of this command sets the ID number
of the monitor. The monitor is subject to the next
command.
Example:
IDSL0002
←
WAIT
←
Searching for monitor with ID number:
2
002
← Found monitor with ID number: 2
Sets volume of monitor with ID
number: 2 to 30.
VOLM0030
←
WAIT
← Processing
OK
IDCK��������Provides screen display of the ID number currently
assigned to a monitor, and the ID number currently
set for IDLK (if any).
Example:
(After executing IDLK0002)
← (Parameter has no meaning.)
IDCK0000
Returned response. The ID
ID : 001
IDLK : 002
002
← number is also displayed on the
monitor screen.
IDCK000 +
The next command is for the monitor
with ID number: 2.
OK
* The IDLK command remains effective until it is
canceled, or power is shut off.
WAIT
ID : 001
IDLK : 000
ID : 002
IDLK : 000
ID : 003
IDLK : 000
ID : 004
IDLK : 000
← Repeater control. (If a command
is used with repeater control, ID
designation using IDSL or IDLK
is canceled.)
OK response from monitor with ID
← number: 2
VOLM0020
← Sets volume to 20.
OK
← number: 1 (the one directly connected
The volume of the monitor with ID
001
to the PC) is set to 20.*
* The IDSL command is effective only once, for the
immediately succeeding command.
19
E
Controlling the Monitor with a PC (RS-232C)
nRepeater control
Setting of the GAMMA user data
This system has a function to allow setting of multiple
monitors connected in a daisy chain using a single command.
This function is called repeater control. You can use Repeater
control function without assigning ID numbers.
[Example]
Set 1
Set 2
Set 3
Set 4
nTo transfer the GAMMA user data
Use the user data transfer commands (UGRW, UGGW and
UGBW). For each of the R, G and B colors, divide the total
512 pieces of user data into 16 blocks, and transfer 32 pieces
of data with each command.
C1
C2
C3
Command field
* If monitors are connected as shown above, you can
execute a command like “Set all monitors’ input settings to
PC D-SUB”.
C4
P1
P2
P3
P4
…
Block number (01 to 16) Data field
S1
S2
Checksum field
xample: To transfer the data of block 1 (0 to 31 levels)
E
of red (R) data
UGRW 01000000010002 … 0031C0
nRepeater control command
One piece of data consists
of 4 digits.
Repeater control is achieved by setting the FOURTH
CHARACTER of the parameter to “+”.
Command Block number
32 pieces of data
Checksum
Example:
VOLM030 +
← Sets volume of all monitors to 30.
In repeater control, responses are returned by all the
connected monitors.
If you want to determine that a value has been returned by a
specific set, assign ID numbers to each monitor in advance.
When some monitors do not return their responses, the
probable cause is that the monitors could not receive the
command or command processing is not complete. Do not
send a new command.
Example: (When 4 monitors are connected, and
assigned ID numbers: 1 through 4)
VOLM030 +
001
OK
002
OK
003
OK
004
nSaving the GAMMA user data
Use the user data save command (UGSV) to save the
transferred user data in the monitor.
If the data is not saved, it will be cleared when:
• The main power switch is off
• STANDBY MODE is LOW POWER and the monitor enters
standby mode
nActivating the GAMMA user data
WAIT
OK
* If data is less than 4 digits, add a “0” (zero) to make it 4
digits.
* The checksum field is the character string (ASCII) data of
lower-order one byte which indicates the sum of the block
number and 32 pieces of data in hexadecimal (0 to F).
To activate the transferred user data, select USER for GAMMA
of the PICTURE menu, or send the corresponding RS-232C
command.
← If 4 monitors are connected in
a chain, reliable operation can
be ensured by sending a new
command only after a reply
has been returned by 4th (last)
monitor.
Repeater control can also be used for reading settings.
nChecking the GAMMA user data
Use the user data read commands (UGRR, UGGR and
UGBR) to return 512 pieces of user data for each of the R,
G and B colors. Divide the data into 16 blocks and return 32
pieces of data with each command. The value to be returned
is not the value stored in the monitor, but the value in the
temporary memory for display. (These values are the same
when the user data save command (UGSV) above has been
sent.)
Example:
TIPS
VOLM ? ? ? +
WAIT
10
001
20
002
30
003
30
004
Volume settings for all
monitors are returned.
TIPS
• If repeater control is used during ID designation (IDSL,
IDLK), the ID designation is canceled.
E
20
• The user data is not initialized by RESET of the PICTURE
menu. To initialize the user data, use ALL RESET of the
FUNCTION menu.
The GAMMA user data initialize command (UGRS) allows
the initialization of the user data only.
Controlling the Monitor with a PC (RS-232C)
RS-232C command table
How to read the command table
Command:
Command field (See page 17.)
Direction:
W When the “Parameter” is set in the parameter field (see page 17), the command functions as described
under “Control/Response Contents”.
R The returned value indicated under “Reply” can be obtained by setting “????”, “
?” or “???+”
(repeater control) in the parameter field (see page 17).
Parameter:
Parameter field (See page 17.)
Reply:
Response (Returned value)
*1:
“●” indicates a command which can be used in power standby mode regardless of the STANDBY MODE
setting.
“○” indicates a command which can also be used in power standby mode when STANDBY MODE is set to
STANDARD.
“–” indicates a command which cannot be used in power standby mode regardless of the STANDBY MODE setting.
*2:
PN-ZB02 (optional) limitations
(A) When PN-ZB02 (optional) is not attached, (B) When PN-ZB02 (optional) is attached.
○: The command can be used.
- : Error (ERR)
Power control/Input mode selection
*2
Function
Command
Direction
Parameter
Reply
Control/Response contents
*1
(A) (B)
POWER CONTROL
POWR
W
0
Switches to standby mode.
1
Returns from standby mode.
R
0 Standby mode
● ○ ○
1 Normal mode
2 Input signal waiting mode
INPUT MODE SELECTION
INPS
W
○ ○
0
Toggle change for input mode. Terminals not selected in INPUT SELECT
cannot be selected.
1
PC DVI-D
“ERR” when AV DVI-D is selected for DVI of INPUT SELECT.
2
PC D-SUB
3
AV COMPONENT
“ERR” when PC RGB is selected for BNC of INPUT SELECT.
4
AV VIDEO
6
PC RGB
“ERR” when AV COMPONENT is selected for BNC of INPUT SELECT.
7
AV DVI-D
“ERR” when PC DVI-D is selected for DVI of INPUT SELECT.
8
AV S-VIDEO
9
AV HDMI
“ERR” when PC HDMI is selected for HDMI of INPUT SELECT.
○
○
○ ○
10
PC HDMI
“ERR” when AV HDMI is selected for HDMI of INPUT SELECT.
○ ○
R
- ○
○ ○
- ○
- ○
● ○
-
1 PC DVI-D
2 PC D-SUB
3 AV COMPONENT
4 AV VIDEO
● ○ ○
6 PC RGB
7 AV DVI-D
8 AV S-VIDEO
9 AV HDMI
10 PC HDMI
SCREEN menu
Function
Command
Direction
Auto
ASNC
W
CLOCK
CLCK
WR
PHASE
positioning
size
RESOLUTION
RESET
Parameter
Reply
Control/Response contents
1
When the input mode is PC D-SUB, PC RGB.
0-1200
0-1200 When the input mode is PC D-SUB, PC RGB.
Varies depending on the signal.
PHSE
WR
0-63
Position of
the longest
direction
HPOS
WR
0-100
0-100 0-800 on PC D-SUB, PC RGB.
Varies depending on the signal.
Position of
the shortest
direction
VPOS
WR
0-100
0-100 0-200 on PC D-SUB, PC RGB.
Varies depending on the signal.
Position of
the longest
direction
HSIZ
WR
0-100
0-100
Position of
the shortest
direction
VSIZ
WR
0-100
Longest
direction
resolution
HRES
WR
300-1920
300-1920 When the input mode is PC D-SUB, PC RGB.
Only even numbers are valid for parameters.
Varies depending on the signal.
Shortest
direction
resolution
VRES
WR
200-1200
200-1200
ARST
W
*1
*2
(A) (B)
0-63 When the input mode is PC D-SUB, PC RGB.
-
○ ○
0-100
1
21
E
Controlling the Monitor with a PC (RS-232C)
PICTURE menu
Function
Command
Direction
Auto
AGIN
W
CONTRAST
CONT
WR
0-60
0-60 0-127 on PC D-SUB, PC RGB.
BLACK LEVEL
BLVL
WR
0-60
0-60 0-127 on PC D-SUB, PC RGB.
TINT
TINT
WR
0-60
0-60
COLORS
COLR
WR
0-60
0-60
SHARPNESS
SHRP
WR
0-24
0-24
ADVANCED
(When the input
mode is AV.)
Parameter
Reply
Control/Response contents
1
When the input mode is PC D-SUB, PC RGB.
FLESH TONE
FLES
WR
0-2
0-2 0: OFF, 1: LOW, 2: HIGH
3D-NR
TDNR
WR
0-2
0-2 0: OFF, 1: LOW, 2: HIGH
MPEG-NR
MPNR
WR
0-1
0-1 0: OFF, 1: ON
3D-Y/C
YCSP
WR
0-1
C.M.S.-HUE
CMHR
WR
-10-10
CMHY
Y
CMHG
G
CMHC
C
CMHB
B
WHITE BALANCE
THRU
W
CMSR
WR
1
-10-10
○
○
-
Resets the hue.
-10-10 R
CMSY
Y
CMSG
G
CMSC
C
CMSB
B
○
M
CRST
W
CMVR
WR
2
-10-10
Resets the saturation.
○
-10-10 R
CMVY
Y
CMVG
G
CMVC
C
CMVB
B
○
M
CRST
W
BMOD
WR
CTMP
○
M
CRST
CMVM
COLOR MODE
-
0-1 0: OFF, 1: ON (When the input mode is AV VIDEO)
CMSM
C.M.S.-VALUE
*2
(A) (B)
-10-10 R
CMHM
C.M.S.SATURATION
*1
3
WR
PRESET
Resets the brightness.
0
0 STD
2
2 VIVID
3
3 sRGB (When the input mode is PC)
0
0 When the input mode is PC DVI-D/PC HDMI.
1-17
USER
○
1-17 From 1: approximately 3,000K to 15: approximately 10,000K
(500K steps)
16: approximately 5,600K, 17: approximately 9,300K
99
99
R-CONTRAST
CRTR
WR
0-256
0-256 “ERR” when CTMP is not set to 99.
G-CONTRAST
CRTG
WR
0-256
0-256
B-CONTRAST
CRTB
WR
0-256
0-256
R-OFFSET
OFSR
WR
-127-127
-127-127
G-OFFSET
OFSG
WR
-127-127
-127-127
B-OFFSET
OFSB
WR
-127-127
-127-127
COPY TO USER
CPTU
W
GAMMA
GAMM
WR
RESET
ARST
W
Command
Direction
TREBLE
AUTR
WR
-5-5
BASS
AUBS
WR
-5-5
-5-5
BALANCE
AUBL
WR
-10-10
-10-10
RESET
ARST
W
0
Copies a preset value to the user setting.
0-2
0-2 0: 1.8, 1: 2.2, 2: 2.4
4-6
4-6 4: User, 5: 2.0, 6: STD
○
-
○
-
2
AUDIO menu
Function
E
22
Parameter
Reply
3
Control/Response contents
*1
*2
(A) (B)
-5-5
○
-
○ ○
Controlling the Monitor with a PC (RS-232C)
SETUP menu
Function
Command
Direction
Parameter
Reply
Control/Response contents
OSD H-POSITION
OSDH
WR
0-100
0-100
OSD V-POSITION
OSDV
WR
0-100
0-100
SCREEN MOTION
SCSV
WR
0-4
0-4
MOTION TIME 1
MTIM
WR
0-20
0-20
MOTION TIME 2
0: OFF, 1-4: PATTERN1-4
PATTERN1
MINT
WR
10-990
10-990
MINT
WR
5-20
5-20
MONITOR
STDR
WR
0-1
0-1
LANGUAGE
LANG
WR
14
14
ENGLISH
1
1
DEUTSCH
2
2
FRANÇAIS
3
3
ITALIANO
4
4
ESPAÑOL
5
5
РУССКИЙ
6
6
PWOD
WR
0
0
1-60
1-60
Per 10 seconds
Per second
0: LANDSCAPE, 1: PORTRAIT
OFF
ON
STANDBY MODE
STBM
WR
0-1
0-1
0: STANDARD, 1: LOW POWER
(“ERR" when SCHEDULE is effective or OFF is selected for LED.)
OFF IF NO OPERATION
ATOF
WR
0-1
0-1
0: OFF, 1: ON
HDMI SETTING
HDMI AUTO VIEW
HDAW
WR
0-1
0-1
0: OFF, 1: ON
HDMI RGB INPUT
RANGE
HDRA
WR
0-2
0-2
0: AUTO, 1: FULL, 2: LIMITED
HOT PLUG CONTROL (DVI)
HPCT
WR
0-1
0-1
0: OFF, 1: ON
HOT PLUG CONTROL (HDMI)
HPCH
WR
0-1
0-1
0: OFF, 1: ON
RS-232C/LAN SELECT
CTLS
WR
0-1
0-1
0 : RS-232C 1 : LAN
ID NUMBER
IDST
W
ID NO. SETTING
0-255
R
Sets the monitor’s ID number. (“0” means “no ID number”.)
0-255
ID NO. SETTING
(ONCE)
IDSL
W
1-255
ID NO. SETTING
(SUBSEQUENT)
IDLK
W
1-255
ID CHECK
IDCK
W
○
○
○ ○ ○
○
○
○
○
○ - ○
○ ○ ○
○ - ○
Returns the monitor’s ID number.
Clears the ID number if one has been designated.
Sets a monitor ID number.
This ID number is effective for the next and all subsequent commands
after this command.
0
○ ○ ○
Clears the ID number if one has been designated.
ID
: xxx
IDLK : yyy
Displays monitor’s own ID number and the selected ID number on the
screen.
BAUD RATE
BAUD
WR
0-2
0-2
0: 9600bps, 1: 19200bps, 2: 38400bps
BRIGHTNESS SENSOR (When
connected to the PN-ZR01 only)
OPTS
WR
0-2
0-2
0: OFF, 1: ON, 2: ON: DISPLAY
WHEN DARK:
AMBIENT
BRIGHTNESS
OPSD
WR
0-99
0-99
WHEN DARK:
SCREEN
BRIGHTNESS
OPDD
WR
0-30
0-30
WHEN LIGHT:
AMBIENT
BRIGHTNESS
OPSL
WR
1-100
1-100
WHEN LIGHT:
SCREEN
BRIGHTNESS
OPDL
WR
1-31
1-31
BRIGHTNESS
SENSOR
SETTING (When
connected to the
PN-ZR01 only)
○
○
Sets a monitor ID number.
This ID number is only effective for the command immediately after this
command.
0
0
*2
(A) (B)
○
PATTERN2-4
Power On Delay
*1
○ ○ ○
○ ○ ○
○ ○ ○
23
E
Controlling the Monitor with a PC (RS-232C)
OPTION menu
Function
Command
Direction
Date/time setting
DATE
WR
AABBCCDDEE
AABBCCDDEE
AA: Year, BB: Month, CC: Day, DD: Time, EE: Minute
○
SCHEDULE
SC01SC08
WR
ABCDEFFGGH
ABCDEFFGGH
Schedule of a specified number
A: Schedule
0= Not effective, 1 = Effective
B: Power
0 = OFF, 1 = ON
C: Day of the week 1 0 = Only once, 1 = Every week, 2 = Every day
D: Day of the week 2 0 = Sunday, 1 = Monday through 6 = Saturday,
9 = Not exist
E: Day of the week 3 0 = Sunday, 1 = Monday through 6 = Saturday,
9 = Not exist
F: Time
00-23
G: Minute
00-59
H: Input
0 = Not specified, 1 = PC DVI-D/AV DVI-D,
2 = PC D-SUB, 3 = PC RGB/AV COMPONENT,
4 = AV VIDEO, 5 = AV S-VIDEO,
6 = PC HDMI/AV HDMI
“ERR” when LOW POWER is selected for STANDBY MODE.
○
INPUT SELECT
AUDIO SELECT
Parameter
Reply
Control/Response contents
*1
INPUT RESOLUTION (AV)
E
○ ○
○ ○ ○ ○
DVI
DVSL
WR
0-1
0-1 0: PC DVI-D, 1: AV DVI-D
BNC
BNSL
WR
0-1
0-1 0: PC RGB, 1: AV COMPONENT
HDMI
HDSL
WR
0-1
0-1 0: PC HDMI, 1: AV HDMI
PC DVI-D
ASDP
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
PC D-SUB
ASAP
WR
1-3
1-3 1: AUDIO(STEREO MINI)
PC HDMI
ASHP
WR
0-1
0-1 0: HDMI, 1: AUDIO(STEREO MINI)
2-3
2-3 2: AUDIO1(RCA), 3: AUDIO2(RCA)
PC RGB
ASCP
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
AV DVI-D
ASDA
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
AV HDMI
ASHA
WR
0-1
0-1 0: HDMI, 1: AUDIO(STEREO MINI)
2-3
2-3 2: AUDIO1(RCA), 3: AUDIO2(RCA)
AV COMPONENT
ASCA
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
-
AV S-VIDEO
ASSA
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
-
AV VIDEO
ASVA
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
-
RESOLUTION CHECK
PXCK
R
PIXEL SETTING
(PC D-SUB, PC
RGB)
PXSL
WR
-
○
2: AUDIO1(RCA), 3: AUDIO2(RCA)
INPUT
RESOLUTION
(PC)
*2
(A) (B)
-
○
-
○
-
○
-
- Returns current resolution in the form of hhh, vvv.
0
0 768) 1366 x 768
1
1 768) 1360 x 768
2
2 768) 1280 x 768
3
3 768) 1024 x 768
5
5 480) 848 x 480
6
6 480) 640 x 480
7
7 1050) 1680 x 1050
8
8 1050) 1400 x 1050
9
9 768) AUTO
10
10 480) AUTO
- 480i, 480p, 1080i, 720p, 1080p, VGA , etc.
-
○ ○
RESO
R
ZOOM2 SPECIAL SETTING
(PC D-SUB, PC RGB)
Z2SP
WR
0-1
0-1 0: OFF, 1: ON
○
SCAN MODE
SCAN
WR
0-2
0-2 0: MODE1, 1: MODE2, 2: MODE3 (When the input mode is AV)
POWER MANAGEMENT (PC)
PMNG
WR
0-1
0-1 0: OFF, 1: ON
POWER MANAGEMENT (AV)
PMAV
WR
0-1
0-1 0: OFF, 1: ON
COLOR SYSTEM
CSYS
WR
0-5
0-5 0: AUTO, 1: PAL, 2: PAL-60, 3: SECAM, 4: NTSC3.58, 5: NTSC4.43
AUDIO OUTPUT(RCA)
AOUT
WR
0-1
0-1 0: VARIABLE, 1: FIXED
AUDIO OUTPUT(RCA)
When the PN-ZB02 (optional) is attached
AOUT
WR
0-2
0-2 0: VARIABLE1, 1: FIXED, 2: VARIABLE2
○
○
○
○ - ○
○ ○ -
AUDIO LEVEL(STEREO MINI)
AIVP
WR
0-1
0-1 0: 1.0Vrms, 1: 0.5Vrms
SELF ADJUST
AADJ
WR
0-1
0-1 0: OFF, 1: ON
AUTO INPUT CHANGE
AINC
WR
0-1
0-1 0: OFF, 1: ON
FAN SPEED
FCTL
WR
0-4
0-4 0: AUTO, 1-4: SPEED 1-4
24
RESOLUTION CHECK
-
○
-
○
-
○
○
○
○ ○
○
○
Controlling the Monitor with a PC (RS-232C)
MULTI menu
Function
Command
Direction
ENLARGE
ENLG
WR
0-1
ENLARGE MODE
EMAG
WR
0-4
EMHV
WR
11-55
11-55 1 x 1 (OFF) to 5 x 5 (“m x n” is expressed as “mn”, where m and n are
the numbers of monitors specified for the longest direction and the
shortest direction respectively.)
IMAGE POSITION (M x N)
EPHV
WR
11-55
11-55 Specifies values in the order of ENLARGE POSITION IN LONGEST/
SHORTEST DIRECTION.
IMAGE POSITION (2 x 2)
EPOS
WR
0-3
IMAGE POSITION (3 x 3)
EPOS
WR
0-8
0-8
IMAGE POSITION (4 x 4)
EPOS
WR
0-15
0-15
IMAGE POSITION (5 x 5)
ENLARGED
SCREEN
POSITIONING
BEZEL WIDTH
Reply
Control/Response contents
*1
*2
(A) (B)
0-1 0: OFF, 1: ON
0-4 0: OFF, 1: 2 x 2, 2: 3 x 3, 3: 4 x 4, 4: 5 x 5
0-3 See the description below.
EPOS
WR
0-24
THE LONGEST
DIRECTION
EPSH
WR
-999-999
-999-999 The setting range depends on the ENLARGE MODE setting and the
IMAGE POSITION.
THE SHORTEST
DIRECTION
EPSV
WR
-999-999
-999-999
BEZEL ADJUST
BEZEL ADJUST
Parameter
0-24
BZCO
WR
0-1
0-1 0: OFF, 1: ON
TOP
BZCT
WR
0-1
0-1 0: OFF, 1: ON
BOTTOM
BZCB
WR
0-1
0-1 0: OFF, 1: ON
RIGHT
BZCR
WR
0-1
0-1 0: OFF, 1: ON
LEFT
BZCL
WR
0-1
SHORTER SIDE
BEZH
WR
0-100
LONGER SIDE
-
○ ○
0-1 0: OFF, 1: ON
0-100
BEZV
WR
0-100
0-100
ENLARGE/IMAGE POSITION SETTING ESTG
WR
XXYY
XXYY XX: ENLARGE MODE (Same as EMAG), YY: IMAGE POSITION (Same
as EPOS)
ESHV
WR
XXYY
XXYY XX: ENLARGE MODE (Same as EMHV), YY: IMAGE POSITION (Same
as EPHV)
• IMAGE POSITION (EPOS) setting
In horizontal orientation
2x2
3x3
4x4
5x5
0
1
0
1
2
0
2
3
3
4
5
4
5
6
7
5
6
7
8
9
6
7
8
8
9
10
11
10
11
12
13
14
13
14
15
16
17
18
19
20
21
22
23
24
1
12
2
3
15
0
1
3
2
4
In vertical orientation
2x2
2
0
3
1
3x3
4x4
6
3
0
7
4
1
8
5
2
12
13
14
15
5x5
0
8
4
9
5
1
10
6
2
11
7
3
20
15
10
5
0
21
16
11
6
1
17
12
7
23
18
13
8
3
24
19
14
9
4
22
2
25
E
Controlling the Monitor with a PC (RS-232C)
PIP/PbyP menu
Function
Command
Direction
PIP MODES
MWIN
WR
0-3
PIP SIZE
MPSZ
WR
1-12
PIP POS
The longest
direction
MHPS
The shortest
direction
MVPS
PIP POS LD+SD BATCH
W
Parameter
Reply
0-100
0-100
R
MPOS
W
0-100
0-100,0-100
R
PIP BLEND
MWBL
WR
PIP SOURCE
MWIP
WR
0-3 0: OFF, 1: PIP, 2: PbyP, 3: PbyP2
1-12
0-100
R
W
Control/Response contents
Specify the position in MPOSxxxyyy format.
(xxx: Longer side, yyy: Shorter side position)
0-100,0-100 Returns a response in (xxx,yyy) format.
(xxx: Longer side, yyy: Shorter side position)
0-15
0-15
1
1 PC DVI-D
2
2 PC D-SUB
3
3 AV COMPONENT
4
4 AV VIDEO
6
6 PC RGB
7
7 AV DVI-D
8
8 AV S-VIDEO
9
9 AV HDMI
10
10 PC HDMI
SOUND CHANGE
MWAD
WR
1-2
1-2 1: MAIN, 2: SUB
MAIN POS (Main screen)
MWPP
WR
0-1
0-1 0: POS1, 1: POS2
PbyP2 POS (Sub screen)
MW2P
WR
0-2
0-2 0: POS1, 1: POS2, 2: POS3
AUTO OFF
MOFF
WR
0-1
0-1 0: MANUAL, 1: AUTO
*1
*2
(A) (B)
○
○
○
○
○
○ ○ ○
○
○
○
- ○
○ ○
- ○
- ○
○ - ○
- ○
- ○
○ ○
- ○
○
○
○ ○
○
○
Initialization/Functional Restriction Setting (FUNCTION) menu
Function
ALL RESET
Command
Direction
RSET
W
Parameter
Reply
0
0-1
E
Control/Response contents
*2
(A) (B)
0: ALL RESET
-
○
0: ALL RESET 1, 1: ALL RESET 2
-
-
ADJUSTMENT LOCK
ALCK
WR
0-2
0-2 0: OFF
OSD DISPLAY
LOSD
WR
0-1
0-1 0: ON, 1: OFF
LED
OFLD
WR
0-1
0-1 0: ON, 1: OFF
“ERR” when LOW POWER is selected for STANDBY MODE.
TEMPERATURE ALERT
TALT
WR
0-2
0-2 0: OFF, 1: OSD & LED, 2: LED
STATUS ALERT
SALT
WR
0-2
0-2 0: OFF, 1: OSD & LED, 2: LED
26
*1
-
○
○
○
○ ○ ○
○
○
Controlling the Monitor with a PC (RS-232C)
Others
Function
Command
Direction
SCREEN SIZE (PC)
WIDE
WR
1-5
1-5 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2
SCREEN SIZE (AV)
WIDE
WR
1-5
1-5 1: WIDE, 2: ZOOM1, 3: ZOOM2, 4: NORMAL, 5: Dot by Dot
VOLUME
VOLM
WR
0-31
MUTE
MUTE
WR
0-1
MODEL
INF1
R
SERIAL NO
INFORMATION
SRNO
R
BRIGHT
VLMP
WR
TEMPERATURE SENSOR
DSTA
R
Parameter
Reply
Control/Response contents
0-31
0-1 0: OFF, 1: ON
*2
(A) (B)
○
○
○
-
Value
0-31
*1
Value
●
0-31
○
0 Internal temperature normal
1 Internal temperature abnormal (Standby mode)
2 Internal temperature abnormal (Temperature is normal now, but it was
abnormal during operation.)
●
3 Internal temperature abnormal (Brightness of the backlight decreases.)
○ ○
4 Temperature sensor abnormal
Temperature acquisition
CAUSE OF LAST STANDBY MODE
ERRT
STCA
R
Value Temperature at temperature sensors 1 through 4 are returned in the
following forms:
[Sensor 1], [Sensor 2], [Sensor 3], [Sensor 4]
Indicates a temperature sensor abnormality when “126” is returned.
W
0
○
Initialization
R
0 No detectable error has occurred
1 Standby mode by POWER button
2 Main power off by the main power switch
3 Standby mode by RS-232C or LAN
●
4 Waiting mode by No Signal
6 Standby mode by abnormal temperature
8 Standby mode by SCHEDULE setting
Commands for setting of the GAMMA user data
Function
Command
Direction
RED GAMMA DATA TRANSFER
UGRW
W
GREEN GAMMA DATA TRANSFER
UGGW
W
BLUE GAMMA DATA TRANSFER
UGBW
W
RED GAMMA DATA READ
UGRR
W
GREEN GAMMA DATA READ
UGGR
W
Parameter
Reply
aaxxxx ··· xxxxcc
(xxxx: 32 pieces)
aa: 01-16
xxxx: 0000-1023
cc: 00-FF
1-16 xxxx ··· xxxx
1-16 (xxxx: 32 pieces)
xxxx: 0000-1023
1-16
Control/Response contents
*1
*2
(A) (B)
aa: Block number
xxxx: 32 pieces of user data
cc: Checksum (ASCII data) of the block number and user data
xxxx: User data of 32 pieces
BLUE GAMMA DATA READ
UGBR
W
USER DATA INITIALIZE
UGRS
W
0
Initialize the user data.
USER DATA SAVE
UGSV
W
0
Save the user data in the monitor.
○ ○ ○
27
E
Controlling the Monitor with a PC (LAN)
When the PN-ZB02 (optional) is attached, your monitor can
be connected to a LAN allowing you to control it from a PC on
the LAN.
You can also configure the monitor to send e-mail notification
when it has a problem.
The connection requires a commercially available LAN cable
(UTP cable, Category 5, straight through).
Network (LAN)
Settings to connect to a LAN
Set the monitor’s IP address and subnet mask to match the
settings of your LAN.
These settings can be made on either the monitor or a PC
connected to the monitor.
The settings depend on the configuration of your LAN. Ask
your LAN administrator for details.
■ To set on the monitor
Set RS-232C/LAN SELECT on the SETUP menu to LAN, and
then set the LAN SETUP options. (See page 10.)
MENU
After setting each item, select SET and press
.
LAN terminal
Hub
LAN cable (commercially available, straight)
TIPS
• You must assign an IP address to the monitor by following
the procedures in “Settings to connect to a LAN”. (See the
description on the right.)
• Your PC must be installed with Internet Explorer (version 6.0
or later).
• To control the monitor via LAN, set RS-232C/LAN SELECT
to LAN. (See page 10.)
• You cannot use RS-232C and LAN control simultaneously.
Initializing personal information
• When the PN-ZB02 (optional) is attached, personal
information such as e-mail addresses can be registered in
the monitor. Before transferring or disposing of the monitor,
initialize all settings by selecting ALL RESET 1. (See
page 16.) Note that ALL RESET 2 will not initialize e-mail
addresses and other settings.
E
28
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to ON.
To set the address manually, set this to OFF.
IP ADDRESS
If the DHCP CLIENT is set to OFF, specify an IP address.
Press
or
to select items, and press
or
to
change the values.
SUBNET MASK
If the DHCP CLIENT is set to OFF, specify the subnet mask.
Press
or
to select items, and press
or
to
change the values.
DEFAULT GATEWAY
If the DHCP CLIENT is set to OFF, specify the default
gateway.
If you are not using a gateway, specify “0.0.0.0”.
Press
or
to select items, and press
or
to
change the values.
RESET
Resets the values of the LAN settings to the factory preset
values.
MENU
Select ON and then press
.
Controlling the Monitor with a PC (LAN)
■ To set from a PC
When the monitor is connected to a PC, LAN settings can be
configured via PC.
Set up process
(1) Connect your monitor to a PC
(2) Specify the PC’s IP address
(3) Configure the monitor’s LAN settings
7. Temporarily change the IP address and subnet mask.
To access the monitor as it is shipped from the factory, set
as follows.
• IP Address: 192.168.150.3
• Subnet Mask: 255.255.255.0
• Default Gateway: (leave blank)
(1) Connecting your monitor to a PC
Connect a commercially available crossover LAN cable
(UPT cable, Category 5) to the LAN port on the PC and this
monitor.
8. Click [OK] and then reboot the PC.
LAN terminal
TIPS
PC
To LAN terminal
LAN cable (commercially available, crossover)
(2) Specifying the PC’s IP address
To configure the monitor’s LAN settings, you must temporarily
change the settings on the PC.
This explanation is based on Windows 7.
1. Log on to the PC with an administrator account.
2. Click [Start], and then click “Control Panel”.
3. Click “View network status and tasks” in “Network and
Internet”.
In “Classic View”, click “Network and Sharing Center”.
4. Click “Local Area Connection” and then “Properties”.
5. Click “Internet Protocol Version 4 (TCP/IPv4)” and then
“Properties”.
6. Make a note of the current IP address, subnet mask, and
default gateway settings.
Make sure you write this information now as you will
be changing the IP address, subnet mask, and default
gateway settings back to these settings afterwards.
•
This monitor is factory preset as shown below.
IP Address
: 192.168.150.2
Subnet Mask
: 255.255.255.0
Default Gateway : 0.0.0.0
(3) Configuring the monitor’s LAN settings
Access the monitor using Internet Explorer.
Controlling the monitor
1. Turn the power ON to the monitor.
2. Set RS-232C/LAN SELECT on the SETUP menu to LAN.
PC operation
3. Launch Internet Explorer, in the “Address” box type
“http://192.168.150.2/” and press the Enter key.
You will be prompted to enter a user name and password.
4. Leave the user name and password boxes blank and click
[OK].
29
E
Controlling the Monitor with a PC (LAN)
5. Click on “LAN SETUP” under NETWORK.
Controlling with a PC
■ Basic operation
You use Internet Explorer on a PC on the LAN to control the
monitor.
1. Launch Internet Explorer on the PC.
2. In the “Address” box, type “http://” followed by your monitor’s
IP address followed by “/”, then press the Enter key.
When prompted to enter a user name and password, type
the user name and password that you specified in the
security settings (see page 32), and click [OK].
If you did not make any security settings, leave the spaces
blank and click on [OK].
3. You can check, control, and change the monitor’s status
and settings by clicking the menu items on the left side of
the screen.
6. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc.
• If you see an [Apply] button next to a setting, click it after
you change that setting.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to “ON”.
To set the address manually, set this to “OFF”.
IP ADDRESS
If the DHCP CLIENT is set to “OFF”, specify an IP
address.
SUBNET MASK
If the DHCP CLIENT is set to “OFF”, specify the subnet
mask.
DEFAULT GATEWAY
If the DHCP CLIENT is set to “OFF”, specify the default
gateway.
If you are not using a default gateway, specify “0.0.0.0”.
7. When the setting is changed, click [Apply].
8. Check the message and click [OK].
9. Exit Internet Explorer.
10.Restore the PC’s IP address jotted in Step 6, “(2)
Specifying the PC’s IP address”.
11.Connect the monitor and the PC to the LAN.
Caution
• Wait 10 seconds after clicking [OK] before proceeding.
• When operating using the remote control unit or similar,
click [Refresh].
E
30
TIPS
• See pages 31 to 35 for details on each setting.
• If you click [Refresh] before the screen finishes updating
the current display, the “Server Busy Error” will appear.
Wait for a moment before operating your monitor again.
• You cannot operate the monitor while it is warming up.
DISPLAY
• If “DHCP CLIENT” is set to “ON”, press
on the
remote control unit two times and then check the monitor’s
IP address.
Controlling the Monitor with a PC (LAN)
■ INFORMATION
Information about this monitor appears.
■ ADJUSTMENT
You can adjust these settings which are also available on the
monitor’s menu.
• SCREEN (See page 9.)
• PICTURE (See Page 9.)
• PICTURE (ADVANCED) (See Page 15.)
• AUDIO (See page 10.)
• SETUP (See page 10.)
• OPTION (See page 11.)
• SCHEDULE (See page 14.)
• MULTI (See page 12.)
• PIP/PbyP (See page 12.)
• FUNCTION (See page 16.)
■ CONTROL
You can control the operations corresponding to the buttons
POWER INPUT SIZE
(
) on the remote control unit. (See page 5.)
TIPS
• In standby mode, Power ON is the operation available.
31
E
Controlling the Monitor with a PC (LAN)
■ NETWORK (LAN SETUP)
■ NETWORK (SECURITY)
This screen allows you to set the settings necessary when the
monitor is connected to a LAN.
This screen allows you to specify the security-related settings.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to “ON”.
To set the address manually, set this to “OFF”.
IP ADDRESS
If the DHCP CLIENT is set to “OFF”, specify an IP address.
SUBNET MASK
If the DHCP CLIENT is set to “OFF”, specify the subnet
mask.
DEFAULT GATEWAY
If the DHCP CLIENT is set to “OFF”, specify the default
gateway.
If you are not using a default gateway, specify “0.0.0.0”.
DNS SERVER
Specify the DNS server address.
If you are not using a DNS server, specify “0.0.0.0”.
RESET
Clicking [Execute] returns all of the LAN SETUP settings
to the factory-preset values except for the DNS SERVER
setting.
E
32
USER NAME / PASSWORD
Sets up a user name and password to restrict access to this
monitor.
After entering a user name and password, click [Apply].
ACCEPT IP ADDRESS
You can limit access to this monitor by registering IP
addresses of PCs that should have access.
To limit access, specify the option “From only specific IP
addresses”. Otherwise, to allow access from any PC, specify
“All IP Addresses”.
IP ADDRESS 1 to 3
If “ACCEPT IP ADDRESS” is set to “From only specific IP
addresses”, enter the IP addresses that you want to allow.
TIPS
• The USER NAME and PASSWORD can be up to 8
alphanumeric characters or symbols.
• To cancel the user name and/or password after it has been
set, make the box empty and click [Apply].
Controlling the Monitor with a PC (LAN)
■ NETWORK (GENERAL)
This screen allows you to specify the general LAN settings.
MONITOR NAME
Specify a name for this monitor as it should appear on the
Internet Explorer screen.
AUTO LOGOUT TIME
Specify the time (in minutes) to elapse before automatically
disconnecting this monitor from the network.
Specify in minutes from 1 to 65535. A value of ‘0’ will disable
this function.
DATA PORT
Specify the TCP port number to use for exchanging data with
the monitor.
Specify a value from 1025 to 65535.
SEARCH PORT
Specify the port number to use when searching for this
monitor.
Specify a value from 1025 to 65535.
INSTALLATION INFORMATION (NAME/LOCATION)
Specify the information to display for this monitor in the
Internet Explorer window.
TIPS
• The MONITOR NAME can be up to 16 alphanumeric
characters or symbols.
• Enter up to 50 characters in the NAME field in the
INSTALLATION INFORMATION.
• Enter up to 100 characters in the LOCATION field in the
INSTALLATION INFORMATION.
■ MAIL (ORIGINATOR)
This screen allows you to configure the e-mail sent periodically
or when the monitor has an error.
The settings depend on the configuration of your LAN. Ask
your LAN administrator for details.
SMTP SERVER
Specify the SMTP server address for sending e-mail.
* When using a domain name, make sure to specify the
DNS server as well. (See page 32.)
ORIGINATOR E-MAIL ADDRESS
Specify the e-mail address for this monitor.
This address becomes the e-mail address of the originator.
ORIGINATOR NAME
Specify the name for the originator.
This name appears in the “Originator Name” field of the
e-mail.
AUTHENTICATION
Specify the authentication method to use when sending
e-mail.
POP SERVER
If the “AUTHENTICATION” method is “POP before SMTP”,
specify the POP server address.
ACCOUNT NAME / PASSWORD
If the “AUTHENTICATION” method is “POP before SMTP”,
specify the account name and password to connect to the
POP server.
TIPS
• You can enter up to 64 alphanumeric characters or symbols
for the ORIGINATOR E-MAIL ADDRESS, ORIGINATOR
NAME, ACCOUNT NAME, and PASSWORD.
• The SMTP SERVER and POP SERVER can be up to 64
characters.
The following characters can be used: a-z, A-Z, 0-9, - , .
33
E
Controlling the Monitor with a PC (LAN)
■ MAIL (RECIPIENT)
■ MAIL (PERIODICAL)
This screen allows you to specify the recipients of the e-mail
sent periodically or when the monitor has an error.
When PERIODICAL for CONDITION of MAIL (RECIPIENT) is
checked, set the date and time to send the mail.
RECIPIENT E-MAIL ADDRESSES
Specify the e-mail addresses to send error notification e-mail
to.
CONDITION
Specify the conditions to send mails.
When you check PERIODICAL, specify the date and time to
send the mails in the PERIODICAL setting.
CONFIRMATION
Sends test e-mail.
This allows you to confirm that the e-mail settings are
configured properly.
Attach the log file to a TEMPERATURE/HARDWARE error
e-mail
When this option is checked, a log is added to the mail which
notifies a temperature or status error.
TIPS
• The RECIPIENT E-MAIL ADDRESSES can be up to 64
alphanumeric characters or symbols.
E
34
DAY OF THE WEEK
Specify the day of the week to send the periodical mails.
TIME
Specify the time of the day to send the periodical mails.
Caution
• Do not turn off the main power when you set to send the
periodical mails.
• Specify the correct date and time. (See page 11.)
If the date and time settings are incorrect, the periodical
mail is not sent properly.
• Regularly confirm that the specified date and time is
correct.
• When LOW POWER is selected for STANDBY MODE,
periodical mails will not be sent in standby mode.
Controlling the Monitor with a PC (LAN)
■ SNMP
You can configure settings related to SNMP.
Caution
• After you set SNMP, click [Switch the main power of
monitor off and on now.] or turn off the monitor and then
turn it on again with the main power switch. When the
monitor restarts, wait about 30 seconds and then start the
next operation.
• If the IP address is changed while the SNMP function is
operational, turn off the monitor and then turn it on again
with the main power switch.
TIPS
• Depending on the SNMP settings, a short delay may occur
before the SNMP is usable. (About 2 minutes)
• Up to 16 alphanumeric letters and symbols can be used for
the community name, user name and password.
■ SERVICE & SUPPORT
(URL INFORMATION)
You can display a specific URL in the URL INFORMATION
field on the INFORMATION screen when an error occurs in
the monitor. (See page 31.)
SNMP SETTING
Set whether to enable or disable SNMP.
VERSION
Set the version of the SNMP to be supported.
COMMUNITY NAME 1 to 3
Set the name of the community required for the access.
USER 1 to 3
Set the user name, password, authentication method and
other options required for access.
TRAP SETTING
Set whether to enable or disable the trap function.
When this function is enabled, a trap will be sent when the
monitor is turned on.
TRAP WHEN AUTHENTICATION FAILS
Set whether the trap function sends a notification when
authentication fails.
TRAP ADDRESS & PORT NO.
Set the destination address and port number of the
notification sent by the trap function.
URL INFORMATION
Enter the URL to display on the INFORMATION screen when
an error occurs on the monitor.
Up to 64 alphanumeric characters or symbols can be used.
CONDITION
Specify the condition to display the URL.
CONFIRMATION
The home page of the specified URL is displayed.
You can check whether the URL you entered is correct.
TIPS
• It is also possible to specify the message text, such as the
name of a contact or a telephone number, to be displayed
instead of the linked URL.
35
E
Troubleshooting
If you are experiencing any problem with your display, before
calling for service, please review the following troubleshooting
tips.
There is no picture or sound.
• Is the power cord disconnected?
• Is the main power switch off?
• Is the monitor in standby mode (the power LED illuminating
in orange)?
• Make sure correct input mode is selected. (See page 5.)
• If any external equipment is connected, make sure the
equipment is operating (playing back).
Remote control does not work.
• Are the batteries inserted with polarity (+,-) aligned? (See
Operation manual.)
• Are the batteries exhausted?
• Point the remote control unit toward the remote control
sensor.
• Is the menu display hidden or is operation disabled? (See
page 16.)
• Is the PN-ZR01 remote control sensor box disconnected?
• If the main unit is connected to multiple monitors, is the
RS-232 cable disconnected? Has the ID No. been set?
Sound from left and right speakers is reversed.
Sound is heard from only one side.
• Are audio cables connected properly?
• Make sure audio cables for external speakers are
connected properly: left and right cables may be reversed
or one of the two cables may not be connected.
• Check the setting of BALANCE for AUDIO menu. (See
page 10.)
There is a picture but no sound.
• Is the sound muted?
• Make sure the volume is not set to minimum.
• Are audio cables connected properly?
• Is the setting of AUDIO SELECT on the OPTION menu
correct? (See page 11.)
Unstable video.
• The signal may be incompatible.
• Try the automatic screen adjustment when the PC D-sub
input terminal or PC RGB input terminals are used.
The video from the PC/AV HDMI input terminal does not
appear properly.
• Is the setting for HDMI of INPUT SELECT on the OPTION
menu correct? (See page 11.)
• Is the HDMI cable HDMI standard compliant? The monitor
will not work with cables that are not standard compliant.
• Is the input signal compatible with this monitor? (See pages
39 to 40)
The video from the PC/AV DVI-D input terminal does not
appear properly.
• Is the setting for DVI of INPUT SELECT on the OPTION
menu correct? (See page 11.)
• Is the input signal compatible with this monitor? (See pages
39 to 40)
• Turn off the power to the connected equipment and then
turn the power on again.
• If the monitors are connected in a daisy chain, turn off the
power to all the monitors connected in a daisy chain and
then turn the power on again.
E
36
The video from the PC RGB input terminals or AV
component input terminals does not appear properly.
• Is the setting for BNC of INPUT SELECT on the OPTION
menu correct? (See page 11.)
• Is the input signal compatible with this monitor? (See pages
39 to 40)
Control buttons do not work.
There is no picture.
• Load noises from outside may be interfering with normal
operation. Turn off the power and turn it on after waiting at
least 5 seconds, and then check the operation.
The input mode changes automatically.
• When the AUTO INPUT CHANGE is ON and no signal
is present in a selected input mode, the AUTO INPUT
CHANGE automatically changes the selected mode to a
mode where a video signal is present.
The input mode may change in the following cases:
-When a computer is in standby mode.
-When video play is stopped with a playback device.
Power LED flashes red.
“STATUS [xxxx]” appears in the corner of the screen.
• Hardware has a problem. Turn off the monitor and request
repair from your SHARP dealer.
(When STATUS ALERT is set to OSD & LED. This varies
depending on the setting.)
When “AUTO DIMMING” is displayed.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight automatically
decreases in order to prevent a further temperature rise. If
you attempt to use
to adjust the brightness while
the monitor is in this state, “AUTO DIMMING” is displayed
and you cannot change the brightness.
• Remove the cause of the excessive temperature rise.
The monitor makes a cracking sound.
• You may occasionally hear a cracking sound from the
monitor. This happens when the cabinet slightly expands
and contracts according to change in temperature. This
does not affect the monitor’s performance.
The Power LED is flashing in red and green alternately.
When “TEMPERATURE” is displayed in the corner of the
screen.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight decreases
automatically in order to prevent high-temperaturerelated problems. When this occurs, “TEMPERATURE” is
displayed on the screen and the Power LED flashes red
and green alternately. (When TEMPERATURE ALERT is
set to OSD & LED. This varies depending on the setting.)
• If the internal temperature rises further, the monitor
automatically enters standby mode. (The Power LED
continues flashing red and green alternately.)
• Remove the cause of the excessive temperature rise.
- If the monitor enters standby mode due to a rise in
temperature, to return to normal display, turn the power
switch off and then back on again. The monitor, however,
will enter standby mode again if the cause of the
temperature rise is not eliminated.
- Check whether the monitor is placed at a location where
a quick rise in temperature is likely. Internal temperature
rises quickly if the vents on the monitor are blocked.
- Internal temperature rises quickly if dust accumulates
inside the monitor or around the vents. Remove dust if
possible. Ask Sharp dealer about removing internal dust.
Specifications
nPN-V601 Product Specifications
Model
LCD component
Max. resolution
Max. colors
Pixel pitch
Viewing angle
Screen active area inch
Computer input signal
Sync signal
PN-V601
60" Class [60 inch (152.4cm) diagonal] TFT LCD
(pixels) 1366 x 768
Approx. 16.77 M colors
0.973 mm (H) × 0.973 mm (V)
176° right/left/up/down (contrast ratio ≥ 10)
(mm) 52-5/8 x 29-7/16 (1328.8 x 747.1)
Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 Ω]
Horizontal/vertical separate (TTL: positive/negative), Sync-on-green,
Composite sync (TTL: positive/negative)
Video color system
NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM
Plug and play
VESA DDC2B
Power management
VESA DPMS, DVI DMPM
Input terminals
Digital
PC/AV
HDMI x 1
Analog
Mini D-sub 15 pin, 3 rows x 1
PC
Audio
3.5 mm mini stereo jack x 1
Serial (RS-232C)
D-sub 9 pin x 1
Digital
DVI-D 24 pin (HDCP compatible) x 1
When PN-ZB02 PC/AV
(optional) is
Analog
BNC *1*2 x 1
PC
attached
Composite video BNC x 1
AV
S-video
x1
Component
BNC (Y, Cb/Pb, Cr/Pr) *1 x 1
Audio
RCA pin (L/R) x 2
Output terminals
Audio
RCA pin (L/R) x 1
Serial (RS-232C)
D-sub 9 pin x 1
Digital
DVI-D 24 pin x 1
When PN-ZB02 PC/AV
(optional) is
External speaker
10 W + 10 W [6 Ω]
attached
LAN terminal
10 BASE-T/100 BASE-TX
[When PN-ZB02 (optional) is attached]
Power requirement
AC 100 V - 240 V, 50/60 Hz
Operating temperature *3
32°F to 104°F (0°C to 40°C)
Operating humidity
20% to 80% (no condensation)
480 W / 1.6 W / 1.8 W
Power consumption
(maximum / input signal waiting mode *4 / standby
mode *5)
Power consumption [PN-ZB02 (optional)]
490 W
Dimensions (excluding protrusions)
inch (mm) Approx. 52-5/8 (W) x 5-7/8 (D) x 29-11/16 (H) (1335.9 x 149.3 x 754.2)
Weight lbs. (kg) Approx. 77.2 (44)
lbs. (kg) Approx. 1.102 (0.5)
Weight [PN-ZB02 (optional)] *1
*2
*3
*4
*5
Cannot be used simultaneously.
Does not support plug and play.
Temperature condition may change when using the display together with the optional equipments recommended by SHARP.
In such cases, please check the temperature condition specified by the optional equipments.
When AUTO INPUT CHANGE is set to OFF.
When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
nPN-ZR01 (optional) Product Specifications
Model
PN-ZR01
Remote control sensor box dimensions inch (mm) Approx. 1-3/8 (W) x 7/8 (D) x 5-1/8 (H) (34.2 x 23 x 130)
Remote control sensor box weight lbs. (kg) Approx. 0.220 (0.1)
37
E
Specifications
nDimensional Drawings
Note that the values shown are approximate values.
52-5/8 [1335.9]
Unit: inch [mm]
5-7/8
[149.3]
VESA holes *
3-5/8
[92.3]
52-5/8 [1335.9]
7-7/8
7-7/8
[200]
[200]
3-15/16 3-15/16
[100] [100]
7-7/8 [200]
29-11/16 [754.2]
Opening height (29-7/16 [747.7])
Opening width (52-5/16 [1329.4])
When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method.
SHARP recommends using M6 screws and tighten the screws.
Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in
serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch
(8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times
or more the weight of the monitor.
nPower management
This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in
order for the monitor’s power management function to work.
DMPM: Digital Monitor Power Management
DPMS: Display Power Management Signaling
DPMS
Screen
Power
consumption*1
Hsync
Vsync
DMPM
ON STATE
Display
480 W
Yes
Yes
Monitor ON
Display
480 W
No
Yes
Active OFF
No display
1.6 W*2
Yes
No
No
No
STANDBY
SUSPEND
OFF STATE
No
display
1.6 W*2
Screen
Power
consumption*1
*1When PN-ZR01 (optional), or PN-ZB02 (optional) is not
connected.
*2When AUTO INPUT CHANGE is set to OFF.
nDDC (plug and play)
The monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters
is exchanged between the two. This function can be used if the computer supports DDC and it has been configured to detect
plug-and-play monitors.
There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.
E
38
Specifications
nCompatible signal timing (PC)
Screen resolution
VESA
640 × 480
800 × 600
848 × 480
1024 × 768
1152 × 864*1
1280 × 768
1280 × 800*1
1280 × 960*1
1280 × 1024*1
Wide
US TEXT
Sun
1360 × 768
1400 × 1050*1
1600 × 1200*1
1680 × 1050*1
1280 × 720
1366 × 768
1920 × 1080*1
720 × 400
1024 × 768
1152 × 900*1
1280 × 1024*1
1600 × 1000*1
Hsync
Vsync
Dot frequency
31.5kHz
37.9kHz
37.5kHz
35.1kHz
37.9kHz
48.1kHz
46.9kHz
31.0kHz
48.4kHz
56.5kHz
60.0kHz
67.5kHz
47.8kHz
60.3kHz
49.7kHz
60.0kHz
64.0kHz
80.0kHz
47.7kHz
65.3kHz
75.0kHz
65.3kHz
44.7kHz
47.7kHz
66.3kHz
67.5kHz
31.5kHz
48.3kHz
53.6kHz
56.6kHz
61.8kHz
71.8kHz
71.7kHz
81.1kHz
68.6kHz
60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
60Hz
70Hz
75Hz
75Hz
60Hz
75Hz
60Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
70Hz
60Hz
66Hz
70Hz
66Hz
76.2Hz
67.2Hz
76Hz
66Hz
25.175MHz
31.5MHz
31.5MHz
36.0MHz
40.0MHz
50.0MHz
49.5MHz
33.75MHz
65.0MHz
75.0MHz
78.75MHz
108.0MHz
79.5MHz
102.25MHz
83.5MHz
108.0MHz
108.0MHz
135.0MHz
85.5MHz
121.75MHz
162.0MHz
146.25MHz
74.4MHz
85.5MHz
148.5MHz
148.5MHz
28.3MHz
64.13MHz
70.4MHz
74.25MHz
94.88MHz
108.23MHz
117.01MHz
134.99MHz
135.76MHz
Digital
DVI*2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
HDMI
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
Analog
(D-SUB/RGB*2)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1 Displays a reduced image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed.
*2 Available when the PN-ZB02 (optional) is attached.
* All are compliant only with non-interlaced.
* Depending on the connected PC, images may not be displayed properly even if the compatible signal described above is input.
* The frequency values for the Sun are reference values.
39
E
Specifications
nCompatible signal timing (AV)
Screen resolution
1920 × 1080p*1
1920 × 1080i*1
1280 × 720p
720 × 576p
720 × 480p
640 × 480p(VGA)
720(1440) × 576i
720(1440) × 480i
Frequency
24Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
DVI-D*2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
HDMI
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Component*2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1 Displays a reduced image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed.
*2 Available when the PN-ZB02 (optional) is attached.
E
40
Specifications
nPC/AV DVI-D
(DVI-D 24 pin)
No.
input terminal pins
Function
No.
Function
nPC/AV HDMI input
(HDMITM Connector)
No.
Function
terminal pins
No.
Function
1
TMDS data 2-
13
N.C.
1
TMDS data 2+
11
TMDS clock shield
2
TMDS data 2+
14
+5V
2
TMDS data 2 shield
12
TMDS clock-
3
TMDS data 2/4 shield
15
GND
3
TMDS data 2-
13
CEC
4
N.C.
16
Hot-plug detection
4
TMDS data 1+
14
N.C.
5
N.C.
17
TMDS data 0-
5
TMDS data 1 shield
15
SCL
6
DDC clock
18
TMDS data 0+
6
TMDS data 1-
16
SDA
7
DDC data
19
TMDS data 0/5 shield
7
TMDS data 0+
17
DDC/CEC GND
8
N.C.
20
N.C.
8
TMDS data 0 shield
18
+5V
9
TMDS data 1-
21
N.C.
9
TMDS data 0-
19
Hot-plug detection
10
TMDS data 1+
22
TMDS clock shield
10
TMDS clock+
11
TMDS data 1/3 shield
23
TMDS clock+
12
N.C.
24
TMDS clock-
nPC D-sub input
(Mini D-sub 15 pin)
No.
terminal pins
Function
No.
nRS-232C input
(D-sub 9 pin)
Function
No.
terminal pins
Function
No.
Function
1
Red video signal input
9
+5V
1
N.C.
6
N.C.
2
Green video signal input
10
GND
2
Transmitted data
7
N.C.
3
Blue video signal input
11
N.C.
3
Received data
8
N.C.
4
N.C.
12
DDC data
4
N.C.
9
N.C.
5
GND
13
Hsync signal input
5
GND
6
GND for red video signal
14
Vsync signal input
7
GND for green video signal 15
8
GND for blue video signal
nPC/AV DVI-D
(DVI-D 24 pin)
No.
DDC clock
output terminal pins
Function
No.
Function
nRS-232C output
(D-sub 9 pin)
No.
Function
terminal pins
No.
Function
1
TMDS data 2-
13
N.C.
1
N.C.
6
N.C.
2
TMDS data 2+
14
+5V
2
Received data
7
N.C.
3
TMDS data 2/4 shield
15
GND
3
Transmitted data
8
N.C.
4
N.C.
16
Hot-plug detection
4
N.C.
9
N.C.
5
N.C.
17
TMDS data 0-
5
GND
6
DDC clock
18
TMDS data 0+
7
DDC data
19
TMDS data 0/5 shield
8
N.C.
20
N.C.
9
TMDS data 1-
21
N.C.
10
TMDS data 1+
22
TMDS clock shield
11
TMDS data 1/3 shield
23
TMDS clock+
12
N.C.
24
TMDS clock-
41
E
PN-V601 G EN10G(1)