Revo RCDY24-1 surveillance camera Instruction manual

Dome Camera with IR Night Vision

Instruction Manual

VER.:1.0, NO.: R040687/2

Thank you for purchasing our product.

Before installing this camera, please read this instruction manual carefully to ensure proper use.

1. Safety Precautious

CAUTION

RISK OF ELECTRIC

SHOCK. DO NOT OPEN!

CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS.

NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems).

 Please do not directly touch the sensor element. If necessary, use a soft cloth moistened with alcohol to wipe off any dust.

 Please be extra careful not to shake the camera.

 Please avoid places where there is direct sunlight.

 When using this camera in places where the lighting differs greatly, please use the auto iris lens with ND filter.

 Please avoid places where temperatures exceed 50

℃ (122 or more, high humidity or where direct rain drops hit, frequent vibrations, or shocks occur.

0

F)

 During the night, if a minimum brightness of 0.1 Lux can not be achieved, install appropriate light fixtures.

 When the camera is not used, keep the lens or the lens cap attached to protect the sensor.

2. Description

The camera uses high sensitive super HAD interline transfer image sensor, and employs digital signal processor (DSP) chip-set for image control, and all integrated state circuitry which provide extremely long life and high reliability. This camera offers excellent image quality with low lag and high burn resistance, and is not subject to distortions from magnetic fields.

Highly resistance to shock and vibration, easy to install, this camera is a very good choice for your color CCTV system.

1

3. Feature

 C olor camera PCB module with 1/3” High Resolution Sensor.

 Employs Digital Signal Processor (DSP) chip-set for image control.

 Pixel number: NTSC=380K / PAL=440K.

 High sensitivity, low smear, high anti-blooming and high S/N ratio.

 Support functions: Auto Electronic Shutter (AES), Auto Iris (AI),

Auto Gain Control (AGC), Auto White Balance (ATW), Back Light

Compensation (BLC), Flickerless mode (FL).

 Vari-Focal Lens (DC Drive).

 DC type, ultra low power consumption.

4. Contents

Item Name of Part Quantity

1 Camera

2 Instruction Manual

3 Bag

A Fixed Retaining Screws for Mounting

B Anchor

1

1

1

4

4

2

5. Installation & Operation

1. Install Preparation

Drill hole in wall if wire needs to go through the wall.

Note!

The following picture illustrates the base of the real IR Dome. The IR

Dome does not provide a central pathway for the cables to run through as it applies RJ12 connection method. Therefore, you must drill hole in wall to be off center of base , in either zone “A” , “B” or “C”.

2. Removing the Dome Cover

Remove the dome cover from the main body by gently turning the cover counter-clockwise to unlock and pull free from the main body.

3

3. Wiring Instructions

Connect the video output to the monitor or other video device through a 75 Ohms type coaxial cable and RJ-12 output to the power source.

RJ-12

4. Install Camera

Use the 4 screws provided to attach the camera and bracket to the ceiling surface or wall.

4

5. Camera Diagram Image Adjustment



You can adjust camera to any direction by using Pan, Tilt, and

Rotate mechanism.



Pan Base moves by 120° on the whole.



Tilt Base covers total 120° angle (60° to each side).



Angle range of Rotate Base is 360°.

6. Attaching the Dome Cover

After all necessary adjustment has been made reinstall the dome cover to the main body by turning the dome clockwise until it locks in place.

5

6. Specification

According to the camera purchased, select and refer to the appropriate specification below:

Model No.

Image Device

Picture Elements

Resolution

Min. Illumination

RCDY24-1 RCDY12-1

1/3 “ Color CCD

(Sharp Chipset)

NTSC: 510 x 492

PAL: 500 x 582

540 TVL

0.02Lux/ F1.2 (Day)

0Lux (IR On)

More than 48 dB

NTSC:1/60~1/100,000, PAL:1/50~1/110,000

0.45

S/N Ratio

Electronic Shutter

Gamma

Sync System

Lens Furnished

White Balance

Gain Control

Video Output

Power Supply

Internal

Board Lens

Auto

Auto

1 Vp-p/ 75 Ohms

DC12V±10%

75mA max.

Power Consumption

IR OFF

24 IR

LED ON

12 IR

LED ON

355mA max.

215mA max.

Infrared Luminary

Filter

Wavelength

Illuminant Distance

Power Supply

Power Consumption

Infrared Illuminator Module

24 IR LED

20 M

Tempered Glass

850nm

DC 12V±10％

12 IR LED

10 M

3.4 W

System Device

-10℃ to 50℃ (14℉ to 122℉)

1.7 W

Operating Temp.

Operating Humidity

Storage Humidity

Dimensions

0% RH~70%RH

0% RH~85%RH

φ110x82 (H) mm

Note: Design and specifications are subject to change without prior notice.

* This symbol indicates the functions are available only on Auto Iris camera models.

6