Lenco TS-10 Instruction manual

EN

What’s in the Box

Main Unit Instruction Manual

3.5mm to 3.5mm Cable

(For TV Headphone Output)

AC Power Cable

1

Important Safety Instructions

Safety

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near

water.

6 Clean only with dry cloth.

7 Do not block any ventilation

openings. Install in accordance

with the manufacturer’s instructions.

8 Do not install near any heat

sources such as radiators, heat

registers, stoves, or other apparatus

(including amplifiers) that produce

heat.

9 Protect the power cord from being

walked on or pinched particularly

at plugs,convenience receptacles,

and the point where they exit from

the apparatus.

10 Unplug this apparatus during

lightning storms or when unused for

long periods of time.

11 Refer all servicing to qualified

service personnel. Servicing is

required when the apparatus has

been damaged in any way, such

as power-supply cord or plug is

damaged, liquid has been spilled

or objects have fallen into the

apparatus, the apparatus has been

exposed to rain or moisture, does

not operate normally, or has been

dropped.

12 Unit shall not be exposed to

dripping or splashing.

13 Do not place any sources of

danger on the apparatus (e.g.

liquid filled objects, lighted candle).

14 The mains plug is used as the

disconnect device, the disconnect

device shall remain readily

operable.

Warning

1 Before operating this system, check

the voltage of this system to see if it

is identical with the voltage of your

local power supply.

2 Do not place this unit close to

strong magnetic field.

3 If the system is brought directly

from a cold to a warm location,

or is placed in a very damp room,

moisture may condense on the

lens inside the player. Should this

occur, the system will not operate

properly. Leave the system turned

on for about an hour until the

moisture evaporates.

4 Should any solid object or liquid fall

into the system, unplug the system

and have it checked by qualified

personnel before operating it any

further.

5 Do not attempt to clean the unit

with chemical solvents as this might

damage the finish. Use a clean, dry

or slightly damp cloth.

6 When removing the power plug

from the wall outlet, always pull

directly on the plug, never yank on

the cord.

2

Identifying the Parts

Main Unit: Top View Rear View

1 /SOURCE

Select LINE IN 1 or LINE IN 2.

2 AUTO POWER Light

Indicate mode of auto power.

Red light: Standby mode.

Green light: play through LINE IN 1.

Yellow light: play through LINE IN 2.

3 + VOLUME -

Increase or decrease the volume level.

4 LINE IN Terminal

Connect to an external audio device.

5 AC~

Connect to a power source.

3

Connections

Connect to TV

This unit is very user friendly, please just

connect it directly to TV’s headphone

jack as below :

Connect Power

Caution:

- Risk of product damage!

- Ensure that the power supply voltage

corresponds to the voltage printed on

the back or the underside of the unit.

1 Connect the LINE IN cable to:

- LINE IN socket on the unit.

- HEADPHONE socket on TV.

2 Unit turn on automatically. Press

the /SOURCE button to select

source.

3 Turn on your TV.

Tip:

You can simply use your TV’s

inherent Remote Control set to

control Vol+/Vol-.

Connect the AC power cord to:

- the AC ~ socket on this unit.

- the wall socket.

Turn On/Off

W h e n y o u c o n n e c t T V o r a n external device to the unit, unit will turn on automatically. Auto Power indication light is green (connect to LINE IN 1) or yellow (connect to

LINE IN 2). And will turn red when disconnected or when you turn off

TV / external device.

NOTE:

If the volume of TV or an external device is too low, the unit also turn off automatically.

4

Adjust Volume Level

During play, press the VOLUME+/- buttons to increase/decrease the volume level.

If the unit is connected to the TV’s

headphne jack, you can also

control the Volume Level by using

the TV’s remote control set directly.

Troubleshooting

To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this unit, check the following points before requesting service.

No power

- Ensure that the AC cord of the

apparatus is connected properly.

- Ensure that there is power at the

AC outlet.

- Press standby button to turn the

unit on.

No Response From the Unit

- Disconnect and reconnect the AC

power plug, then turn on the unit

again.

Specifications

General

Power Requirements . AC 230V ~ 50Hz

Power Consumption .................... 6.5W

Output Power ..............7.5W x 2 + 15W

Total Harmonic Distortion .....................

..........................................1%(1kHz, 1W)

Audio Input Sensitivity/Impedance

LINE: ................................ 500mV/47kΩ

Frequency Response ............................

......................... 40Hz - 20kHz(+0 / -3dB)

Unit Dimensions (W x H x D) ..................

.................................. 584 x 50 x 218mm

Speaker

Front

Impedance ......................................3 Ω

Rate Power .................................... 10W

Subwoofer

Impedance ......................................6 Ω

Rate Power .................................... 30W

If at any time in the future you should need to dispose of this product please note that: Waste electrical products should not be disposed of with household waste. Please recycle where facilities exise. Check with your Local Authority or retailer for recycling advise. (Waste Electrical and Electronic Equipment Directive.)

5