Package Content
Z1-Proud
3-axis handheld stabilizing
gimbal for GOPRO
Instruction Manual
Manufactured by Zhiyun Tech
3-axis handheld camera stabilizer
1
Camera Holder
1
M2.5x 9mm Thumb Screw
2
M2.5x19mm Thumb Screw
2
Gopro Charging Wire
1
18650 LIPO Battery Charger
1
18650 LIPO Battery
2
Micro USB Charger Cable
1
Warranty Card
1
Certificate
1
User's Manual
1
V1.00
Note:
Mode Status Indicator
Install the GOPRO
before connecting power.
Micro USB port – for
setting and firmware
upgrade
Camera Holder
UP
Battery
indicator
DOWN
Gopro3
18650 LIPO
battery x2
To use the M2.5x9mm Thumb
Screw for GOPRO only.
MODE
Power Button
Camera Holder
Different Rotation Angle
Gopro3
45°
Gopro LCD BacPac
270°
270°
Camera Charging port
To use the M2.5x19mm
Thumb Screw for GOPRO
with LCD BacPac.
①
②
Different Modes Instruction
88mm(with LCD BACPAC)
● Heading Following Mode (Default): Pitch and roll are locked.
Heading rotates smoothly follow the direction of the handheld.
● Locking Mode: Heading, pitch and roll are locked.
● Heading and Pitch Following Mode: Roll is locked. Heading
and pitch rotate smoothly follow the direction of the handheld.
78mm(without LCD BACPAC)
Buttons and Modes Instruction
Working Mode
Mode Indicator
Down/Up Button
Heading Following Mode
Blink slowly
Pitch adjustment
Locking Mode
Light up
Pitch adjustment
295mm
Extended handle
Roll adjustment
Heading and Pitch Following Mode Blink quickly
Battery Indicator Instruction
Battery Indicator Status
67mm
Description
Blink 4 times
100% Power
Blink 3 times
75% Power
Blink 2 times
50% Power
Blink 1 times
25% Power
Charger indicator
(The signal will show green
once finish charging)
Note: If the battery indicator blinks continuingly, the battery is out of
power. Please charge the battery as soon as possible.
Operation:
Rechargeable Battery
● Power Switch
: Install the battery and press the power button, the stabilizer will in standby mode after five seconds.
● On/Off
: After connecting to power, long press “MODE” for 1 second to switch standby mode/ working mode.
● Mode Switch
: In working mode, press “MODE” to switch Heading Following Mode/ Locking Mode. Press “MODE”
Press the power button again to cut off power.
2 times to turn on Heading and Pitch Following Mode; press “MODE” again to turn on previous
mode.
● Angle Adjusting : User can adjust the pitch/roll angle through UP / DOWN buttons.
: calibrate the gyro and accelerator if: 1. Horizontal angle offset; 2. Operate
● Calibration
③
again after a long time; 3. Transit the device under different temperature.
Battery type: 18650 LIPO battery
Capacity: 2000mAh
Charge Time: 3 hours
Note:
For connecting power to 18650 battery
charger, please prepare portable charger,
or connect to a USB port of PC.
Micro USB 5V
power input port
④
Specification:
minimum standard maximum
Note
Working Voltage
6.8V
8.4V
12.6V
Working Current
50mA
120mA
2A
Follow Accuracy(Motionless)
±0.01°
Follow Accuracy(Motion)
±0.1°
±0.2°
±0.5°
Tilt Working Angle
-90°
0°
+180°
Roll Working Angle
-45°
0°
+45°
Heading Working Angle
-135°
0°
+135°
Vertical
handheld
Heading Working Angle
-45°
0°
+45°
Leveled
handheld
Tilt Speed
1°/S
50°/S
Heading Speed
1°/S
80°/S
Battery Operation Time(25°C)
Operation Temperature
Weight
±0.04°
7h
10h
12h
-20℃
25℃
45℃
335g
Vertical
handheld
This device has been calibrated by the
manufacturer. Warranty void if
disassemble any components.
We reserve the right of final
explanation and revision of the
instruction manual. For the latest
version, please refer to official website.
For user instruction, firmware upgrade,
and more information:
www.zhiyun-tech.com
2000mAh×2
without battery
and camera
Note:
Please don’t operate the handheld gimbal over working
range; the handheld gimbal would be in self-protection mode,
and the operation would be effected.
⑤
Manufactured by Zhiyun Tech
⑥
Open as PDF
Similar pages