Jack Randall
100 NW 11th Street, Boca Raton, FL 33432 TEL 561-955-9770 FAX 561-955-9760
www.nav-tv.com
info@nav-tv.com
MY FORD TOUCH REAR VIEW CAMERA INTEGRATION KIT
NTV-KIT391 for: 2011-2013 Ford Edge & Lincoln MKX, 2012-2013 Ford Focus & 2013 Ford Taurus, Fusion, Flex,
Fiesta, F-Series Trucks, Escape & C-MAX.
NTV-KIT-392 for: 2011-2013 Explorer
Programs the My Ford Touch radio for rear view camera
 THIS MODULE LOCKS TO THE VEHICLE’S VIN NUMBER AND CAN
ONLY BE USED TO PROGRAM A REVERSE CAMERA ON ONE
VEHICLE.
 AFTER PROGRAMMING THE MODULE SHOULD REMAIN WITH
THE VEHICLE IN THE GLOVE BOX OR OTHER COMPARTMENT.
 IF A MISTAKE IS MADE THE MODULE MUST BE
UNPROGRAMMED BEFORE IT CAN BE USED ON A SEPARATE
VEHICLE. (SEE PAGE 4)
Included parts
1. OBD2 Program cable
2. OBD2 Programmer
3. Video adapter
1|Page
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
Jack Randall
Installation:
1. Remove the screen from the dash, unplug all the connectors & set the screen to the side. All
connections except the ground will be made at the 54 pin plug behind the monitor.
2. Using a pick tool, lift the locking tabs on either side of the connector cover to gain access to the
wiring.
3. DO NOT PLUG THE 14 PIN CONNECTOR INTO THE VIDEO ADAPTER UNTIL ALL CONNECTIONS
HAVE BEEN MADE!
4. Locate the Violet & White/Violet wires on the video adapter board. The wires will already have
the appropriate pins crimped to the ends.
5. The plug is labeled on one side from pin 1 to pin 18. Insert the pre-pinned video adapter wires
into the specified locations until they lock into place. If 14 and 15 are populated skip to 6 on the
top of the next page. Once inserted, gently tug on the wire to verify it’s locked into place. The
wires do require force to insert and they will be very snug.
a. Violet – Pin 15; differential video +
b. White/Violet – Pin 14; differential video -
2|Page
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
Jack Randall
6. If pins 14 & 15 are already populated from the factory, attach the violet wire to the wire in pin
15 and the white/violet wire to the wire in pin 14.
7. Locate pins 20 (Purple/grey) and 19 (Blue/grey) on the factory connector. Strip back a 1/2"
section of insulation from both wires making sure NOT to cut them in half. Attach the
White/Brown wire from the video adapter to the Blue/grey wire in pin 19 of the factory harness.
Attach the Brown wire from the video adapter to the Purple/grey wire in pin 20 of the factory
harness. SOLDER these connections and insulate. NOTE: T-TAPS WILL NOT WORK PROPERLY
FOR THIS CONNECTION AND WILL VOID THE PRODUCT WARRANTY!!!!!
8. The Black wire from the video adapter requires a chassis ground connection. Attach this wire to
a clean and paint free bare metal surface. DO NOT CONNECT THIS WIRE TO THE RADIO
GROUND!
9. Attach the yellow wire from the video adapter to Pin 1 (12 volt constant) of the factory 54 pin
harness.
10. The WHITE/BLUE wire of the video adapter is NOT USED on the MYFORD TOUCH CAM
INTERFACE.
11. Ground your camera negative wire to a solid bare metal chassis ground at the back of the
vehicle and run the RCA and power connection from your rear view camera to the video
interface. Plug the RCA from your rear view camera into the female RCA connection at the video
adapter. The RED wire of the video interface will output 12 Volt + Accessory to power your
camera. The output is limited to 1 AMP. If your camera requires more than 1 AMP to function,
make sure to use a relay.
Wire side
14
8
7
1
3|Page
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
Jack Randall
12. After all connections have been made, plug the 14 pin Molex into the video adapter and
reassemble the factory 54 pin connector.
13. Plug the factory 54 pin connector back into the monitor.
14. Leave all connections accessible and skip to the programming section below.
Programming:
NOTE 1: The MYFORD TOUCH CAM PROGRAMMER MUST BE ORDERED WITH THE PROPER
FILE. There are 2 different files; one for the Ford Explorer (NTV-KIT392), and another for all
other My Ford Touch equipped vehicles (NTV-KIT391). The files are not interchangeable!
NOTE 2: THE MYFORD TOUCH PROGRAMMER CAN ONLY BE USED TO ACTIVATE THE REAR
VIEW CAMERA ON ONE VEHICLE AND MUST REMAIN WITH THAT VEHICLE. FACTORY FORD
MYFORD TOUCH UPDATES MAY DELETE THE REAR VIEW CAMERA OPTION AND PUT THE
VEHICLE BACK TO AN “AS BUILT” STATE. IF THIS HAPPENS THE UNIT WILL NEED TO BE
REACTIVATED BY COMPLETING THE PROGRAMMING STEPS AGAIN. NAV-TV RECOMMENDS
THAT THE MYFORD TOUCH PROGRAMMER BE KEPT WITH THE VEHICLE IN THE GLOVE BOX OR
OTHER COMPARTMENT AT ALL TIMES.
1. BE SURE THE WHITE/BLUE WIRES ARE NOT CONNECTED.
2. With the key OFF, plug the MY FORD TOUCH PROGRAMMER into the OBD2 plug underneath the
driver’s side dash.
3. Turn the key to the RUN position and keep it in the RUN position until the radio is completely
done with the programming sequence (see below for a description).
4. The radio will program and restart in approximately 20 seconds. Once restarted, the radio will
go into a self-diagnostics screen. It will take approximately 1-2 minutes to boot into the radio
screen.
5. Once the radio restarts, place the vehicle into reverse and verify the radio displays the rear view
camera image or goes to a blank screen if a camera is not installed yet. NOTE: IF THE REAR VIEW
CAMERA IS NOT ALREADY CONNECTED TO THE RADIO THE SCREEN MAY TAKE AS LONG AS 15
SECONDS TO GO TO A BLACK SCREEN AND MAY GIVE YOU A WARNING THAT SAYS "CAMERA
FAULT".
6. Verify that the screen displays a rear view camera image once the vehicle is placed into reverse.
If the image is displayed correctly, reassemble the vehicle and place the MYFORD TOUCH
PROGRAMMER INTO THE GLOVE BOX OF THE VEHICLE.
7. Reassemble the vehicle.
Un-programming:
NOTE: BEFORE THE MYFORD TOUCH PROGRAMMER CAN BE USED ON ANOTHER VEHICLE, THE
ORIGINAL VEHICLE MUST BE UN-PROGRAMMED.
4|Page
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
Jack Randall
1. The MYFORD TOUCH CAM PROGRAMMER WILL NOT UN-PROGRAM ANY VEHICLE IF THE
VEHICLE WAS ORIGINALLY PROGRAMMED WITH ANOTHER PROGRAMMER, INCLUDING
FACTORY PROGRAMMING, OR A DIFFERENT MYFORD TOUCH CAM PROGRAMMER.
2. Connect the white/blue wires TOGETHER.
3. With the key OFF, plug the MY FORD TOUCH PROGRAMMER into the OBD2 plug underneath the
driver’s side dash.
4. Turn the key to the RUN position and keep it in the RUN position until the radio is completely
done with the un-programming sequence (see below for a description).
5. The radio will un-program and restart in approximately 20 seconds. Once restarted the radio will
go into a self-diagnostics screen. It will take approximately 1-2 minutes to boot into the radio
screen.
6. Once the radio restarts, place the vehicle into reverse and verify the radio DOES NOT change
states, i.e. blank screen/rear view camera.
*Note: The programmer will not un-program the factory installed rear view camera option.
FAQ
Q. The radio went through the programming sequence but I have a blank screen or distorted view of the camera
image when I place the vehicle into reverse.
A. Verify that the video adapter and the rear view camera have sufficient power and ground. If using the reverse
lamps to power the camera, a relay is required. The lamp output has a low current rating and will not drive a
camera. The red wire on the video adapter provides a 1 AMP accessory output for your convenience.
Q. The rear view camera image is distorted and lacks color.
A. Check that the video adapter violet and white/violet wires are populated in the proper pin locations, and that
the camera has sufficient voltage and a proper ground.
Q. The system went through the programming sequence, but the screen doesn’t go into rearview camera mode.
A. Verify that the white/blue wires weren’t connected when programming.
Q. I plugged in the unit, verified the white/blue wires were disconnected and cycled the key on, but the radio
didn’t change status or program rear view camera.
A. The programmer can only be used to program one vehicle and locks to the VIN number of that vehicle. You must
purchase a separate MYFORD TOUCH PROGRAMMER for each vehicle.
Q. I programmed the wrong vehicle or the customer backed out of the sale. What steps do I need to take to ensure
that I can still use this MYFORD TOUCH PROGRAMMER on a different vehicle?
A. The vehicle must first be un-programmed before the MYFORD TOUCH PROGRAMMER will work on another
vehicle. Follow the un-programming steps on this page before attempting to use the programmer on a different
vehicle.
If, and ONLY if, after checking all the connections and rereading this instruction manual you still experience issues, please call
our technical support department at 1-866-477-3336 x 2 between the hours of 9-6 EST Monday through Friday.
5|Page
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
Open as PDF
Similar pages