HP 2910 al Switch Series - Thomas

QuickSpecs
HP 2910 al Switch Series
Overview
HP 2910-24G al Switch
HP 2910-48G al Switch
HP 2910-48G-PoE+ al Switch
Models
HP 2910-24G al Switch
HP 2910-48G al Switch
HP 2910-24G-PoE+ al Switch
HP 2910-48G-PoE+ al Switch
J9145A
J9147A
J9146A
J9148A
Key Features
High-performance Gigabit Ethernet access switch
Four optional 10 GbE (CX4 and/or SFP+) ports
IEEE 802.3af/802.3at functionality ( PoE/PoE+)
Layer 2 and Layer 3 plus static IP and RIP routing
Lifetime warranty, sFlow, ACLs, and rate limiting
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 1
QuickSpecs
HP 2910 al Switch Series
Overview
Product overview
The HP 2910 al Switch Series consists of four switches: the HP 2910-24G al and 2910-24G-PoE+ al Switches with 24 10/100/1000
ports, and the HP 2910-48G al and 2910-48G-PoE+ al Switches with 48 10/100/1000 ports. Each switch has four dual-personality
ports for 10/100/1000 or mini-GBIC connectivity. In addition, the 2910 al Switch Series supports up to four optional 10 Gigabit Ethernet
(CX4 and/or SFP+) ports, thereby offering the most flexible and easy-to-deploy uplinks in its class. Together with static and RIP IPv4
routing, robust security and management, enterprise-class features, free lifetime warranty, and free software updates, the 2910
series is a cost-effective, scalable solution for customers who are building high-performance networks. These switches can be
deployed at enterprise edge and remote branch offices, converged networks, and data center top of rack.
Features and Benefits
Quality of Service (QoS)
Traffic prioritization (IEEE 802.1p): allows real-time traffic classification into eight priority levels mapped to eight queues
Layer 4 prioritization: enables prioritization based on TCP/UDP port numbers
Class of Service (CoS): sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol, TCP/UDP
port number, source port, and DiffServ
Rate Limiting: per-port ingress enforced maximums
Connectivity
10 Gbps Ethernet connectivity: up to four optional and flexible 10-Gigabit ports (CX4 and/or SFP+), with optional interconnect
kit for short-distance connectivity
IPv6:
IPv6 host: allows the switches to be managed and deployed at the edge of IPv6 networks
Dual stack (IPv4/IPv6): provides transition mechanism from IPv4 to IPv6; supports connectivity for both protocols
MLD snooping: forwards IPv6 multicast traffic to the appropriate interface; prevents IPv6 multicast traffic from flooding
the network
IEEE 802.3af Power over Ethernet (PoE): provides up to 15.4 W per port to IEEE 802.3af-compliant PoE-powered devices such
as IP phones, wireless access points, and security cameras
IEEE 802.3at Power Over Ethernet Plus: provides up to 30 W per port to IEEE 802.3 for PoE/PoE+ powered devices such as
video IP phones, IEEE 802.11n wireless access points, and advanced pan/zoom/tilt security cameras
Pre-standard PoE support: detects and provides power to pre-standard PoE devices; see list of supported devices in the
product FAQ at: www.hp.com/networking/support
Auto-MDIX: automatically adjusts for straight-through or crossover cables on all 10/100 and 10/100/1000 ports
Dual-personality functionality: includes four 10/100/1000 ports or SFP slots for optional fiber connectivity such as Gigabit-SX,
-LX, -LH, 100-FX, 100-BX, and 1000-BX
Single IP Address Management: single IP address management for a virtual stack of up to 16 switches
Performance
High-performance architecture: 128 Gbps switching fabric with up to 95 Mpps (24-port switches) and 176 Gbps switching fabric
with up to 131 Mpps (48-port switches)
Selectable queue configurations: allows for increased performance by selecting the number of queues and associated memory
buffering that best meet the requirements of the network applications
Resiliency and high availability
IEEE 802.1s Multiple Spanning Tree: provides high link availability in multiple VLAN environments by allowing multiple
spanning trees; provides legacy support for IEEE 802.1d and IEEE 802.1w
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 2
QuickSpecs
HP 2910 al Switch Series
Overview
IEEE 802.3ad Link Aggregation Protocol (LACP) and HP port trunking: support up to 24 trunks, each with up to 8 links (ports)
per trunk
Optional redundant power supply: supplies backup power in case of power failure (NOTE: HP 620 Redundant/External Power
Supply provides only RPS functionality)
Manageability
RMON, XRMON, and sFlow: provide advanced monitoring and reporting capabilities for statistics, history, alarms, and events
Uni-Directional Link Detection (UDLD): monitors a link between two switches and blocks the ports on both ends of the link if
the link goes down at any point between the two devices
Command authorization: leverages RADIUS to link a custom list of CLI commands to an individual network administrator's login;
also provides an audit trail
Dual flash images: provides independent primary and secondary operating system files for backup while upgrading
Multiple configuration files: allow multiple configuration files to be stored to a flash image
Friendly port names: allow assignment of descriptive names to ports
Find-Fix-Inform: finds and fixes common network problems automatically, then informs administrator
Software updates: free downloads from the Web
Troubleshooting: ingress and egress port monitoring enable network problem solving
Layer 2 switching
VLAN support and tagging: supports IEEE 802.1Q (4,094 VLAN IDs) and 256 VLANs simultaneously
GARP VLAN Registration Protocol (GVRP): allows automatic learning and dynamic assignment of VLANs
Jumbo packet support: supports up to 9220-byte frame size to improve the performance of large data transfers
IEEE 802.1v protocol VLANs: isolate select non-IPv4 protocols automatically into their own VLANs
Layer 3 routing
Static IP routing: provides manually configured routing; includes ECMP capability
Routing Information Protocol (RIP): provides RIPv1 and RIPv2 routing
Security
Multiple user authentication methods:
IEEE 802.1X: is an industry-standard method of user authentication using an IEEE 802.1X supplicant on the client in
conjunction with a RADIUS server
Web-based authentication: is similar to IEEE 802.1X and provides a browser-based environment to authenticate clients
that do not support the IEEE 802.1X supplicant
MAC-based authentication: authenticates the client with the RADIUS server based on the client's MAC address
Authentication flexibility:
Multiple IEEE 802.1X users per port: provides authentication of up to eight IEEE 802.1X users per port; prevents a user
from "piggybacking" on another user's IEEE 802.1X authentication
Concurrent IEEE 802.1X and Web or MAC authentication schemes per port: switch port will accept any IEEE 802.1X and
either Web or MAC authentications
Access control lists (ACLs): provide IP Layer 3 filtering based on source/destination IP address/subnet and source/destination
TCP/UDP port number
Identity-driven ACL: enables implementation of a highly granular and flexible access security policy and VLAN assignment
specific to each authenticated network user
Dynamic ARP protection: blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data
DHCP protection: blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
Port monitoring for network threats: provides sampled port traffic using sFlow technology to the HP Network Immunity
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 3
QuickSpecs
HP 2910 al Switch Series
Overview
Manager (NIM) application for Network Behavior Anomaly Detection (NBAD) analysis to detect and mitigate threats at the port
where the threat originated
Source-port filtering: allows only specified ports to communicate with each other
RADIUS/TACACS+: eases switch management security administration by using a password authentication server
Secure shell: encrypts all transmitted data for secure remote CLI access over IP networks
Secure FTP: allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized
copying of a switch configuration file
Secure Sockets Layer (SSL): encrypts all HTTP traffic, allowing secure access to the browser-based management GUI in the
switch
Port security: allows access only to specified MAC addresses, which can be learned or specified by the administrator
MAC address lockout: prevents particular configured MAC addresses from connecting to the network
Switch management logon security: helps secure switch CLI logon by optionally requiring either RADIUS or TACACS+
authentication
STP BPDU port protection: blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged
BPDU attacks
USB Secure Autorun (requires HP PCM+): deploys, diagnoses, and updates a switch using a USB flash drive; works with a secure
credential to prevent tampering
STP Root Guard: protects the root bridge from malicious attacks or configuration mistakes
Custom banner: displays security policy when users log in to the switch
Per-port broadcast throttling: selectively configures broadcast control on heavy traffic port uplinks
Convergence
IP multicast snooping and data-driven IGMP: automatically prevent flooding of IP multicast traffic
LLDP-MED (Media Endpoint Discovery): is a standard extension of LLDP that stores values for parameters such as QoS and VLAN
to automatically configure network devices such as IP phones
IEEE 802.1AB Link Layer Discovery Protocol (LLDP): is an automated device discovery protocol that provides easy mapping of
network management applications
PoE and PoE+ allocations: support multiple methods (automatic, IEEE 802.3at dynamic, LLDP-MED fine-grain, IEEE 802.3af
device class, or user specified) to allocate and manage PoE/PoE+ power for more efficient energy savings
Monitor and diagnostics
Port mirroring: enables traffic on a port to be simultaneously sent to a network analyzer for monitoring
Warranty and support
Lifetime warranty: for as long as you own the product with advance replacement and next-business-day delivery (available in
most countries)†
Electronic and telephone support: limited electronic and telephone support is available from HP; to reach our support centers,
refer to www.hp.com/networking/contact-support; for details on the duration of support provided with your product purchase,
refer to www.hp.com/networking/warrantysummary
Software releases: to find software for your product, refer to www.hp.com/networking/support; for details on the software
releases available with your product purchase, refer to www.hp.com/networking/warrantysummary
†HP warranty includes repair or replacement of hardware for as long as you own the product, with next business day advance
replacement (available in most countries). The disk drive included with HP AllianceOne Advanced Services and Services zl Modules, HP
Threat Management Services zl Module, HP AllianceOne Extended zl Module with Riverbed Steelhead, HP MSM765zl Mobility Controller
and HP Survivable Branch Communication zl Module powered by Microsoft Lync has a five-year hardware warranty. For details, refer to
the Software license and hardware warranty statements at www.hp.com/networking/warranty.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 4
QuickSpecs
HP 2910 al Switch Series
Technical Specifications
HP 2910-24G al Switch (J9145A)
Ports
Physical characteristics
20 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE
802.3ab Type 1000BASE-T); Media Type: Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
4 dual-personality ports; each port can be used as either an RJ-45 10/100/1000 port (IEEE 802.3 Type
10Base-T; IEEE 802.3u Type 100Base-TX; IEEE 802.3ab 1000Base-T Gigabit Ethernet) or as a mini-GBIC
slot (for use with mini-GBIC transceivers)
1 RJ-45 serial console port
Supports a maximum of 4 10GbE ports, with optional module
Dimensions
17.4(w) x 14.4(d) x 1.73(h) in (44.2 x 36.58 x 4.4 cm) (1U height)
Weight
Memory and processor
Mounting
Performance
Environment
10.92 lb (4.95 kg)
Processor
Dual ARM1156T2S @ 515 MHz, 4 MB flash, 1 GB compact flash, 512 MB
SDRAM; packet buffer size: 6 MB
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface
mounting only
1000 Mb Latency
< 2.9 µs (FIFO 64-byte packets)
10 Gbps Latency
< 1.3 µs (FIFO 64-byte packets)
Throughput
up to 95 million pps (64-byte packets)
Switching capacity
128 Gbps
Routing table size
2000 entries (IPv4)
MAC address table size
16000 entries
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Non-operating/
Storage temperature
-40°F to 158°F (-40°C to 70°C)
Non-operating/
15% to 95% @ 149°F (65°C), noncondensing
Storage relative humidity
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 53.5 dB, Pressure: 39.4 dB; DIN 45635T.19 per ISO 7779
Electrical characteristics Description
Maximum heat
dissipation
The switch automatically adjusts to any voltage between 100-127 and 200240 volts and either 50 or 60 Hz
279 BTU/hr (295 kJ/hr)
Voltage
100-127/200-240 VAC
Current
1.7/0.9 A
Idle power
49 W
Maximum power rating
82 W
Frequency
50/60 Hz
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 5
QuickSpecs
HP 2910 al Switch Series
Technical Specifications
Notes
Safety
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure with
fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
EN 60950/IEC 60950; CAN/CSA 22.2 No. 60950; EN 60825; UL 60950
Emissions
FCC part 15 Class A; EN 55022/CISPR-22 Class A; VCCI Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2; 4 kV CD, 8 kV AD
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV / 2 kV AC, 1 kV signal, 0.5 kV DC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m
Voltage dips and
interruptions
IEC 61000-4-11; > 95% reductions, 0.5 period; 30% reduction, 25 periods
Harmonics
IEC 61000-3-2
Flicker
IEC 61000-3-3
Management
HP PCM+; HP PCM; command-line interface; Web browser; out-of-band management (serial RS-232C)
Notes
When using mini-GBICs with this product, mini-GBICs with revision "B" or later (product number ends with
the letter "B" or later, e.g., J4858B, J4859C) are required.
3-year, 4-hour onsite, 13x5 coverage for hardware (U2855E)
3-year, 4-hour onsite, 24x7 coverage for hardware (U2856E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (U6304E)
3-year, 24x7 SW phone support, software updates (UE262E)
Installation with minimum configuration, system-based pricing (U4826E)
Installation with HP-provided configuration, system-based pricing (U4830E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR868E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR869E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UR870E)
4-year, 24x7 SW phone support, software updates (UR871E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR872E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR873E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UR874E)
5-year, 24x7 SW phone support, software updates (UR875E)
3 Yr 6 hr Call-to-Repair Onsite (UW356E)
4 Yr 6 hr Call-to-Repair Onsite (UW357E)
5 Yr 6 hr Call-to-Repair Onsite (UW358E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR893E)
1-year, 24x7 software phone support, software updates (HR892E)
1-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HS610E)
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HS611E)
3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HS612E)
Services
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 6
QuickSpecs
HP 2910 al Switch Series
Technical Specifications
3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS613E)
4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HS614E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS615E)
5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HS616E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS617E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
HP 2910-48G al Switch (J9147A)
Ports
Physical characteristics
44 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE
802.3ab Type 1000BASE-T); Media Type: Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
4 dual-personality ports; each port can be used as either an RJ-45 10/100/1000 port (IEEE 802.3 Type
10Base-T; IEEE 802.3u Type 100Base-TX; IEEE 802.3ab 1000Base-T Gigabit Ethernet) or as a mini-GBIC
slot (for use with mini-GBIC transceivers)
1 RJ-45 serial console port
Supports a maximum of 4 10GbE ports, with optional module
Dimensions
17.42(w) x 14.4(d) x 1.73(h) in (44.25 x 36.58 x 4.4 cm) (1U height)
Weight
Memory and processor
Mounting
Performance
Environment
11.2 lb (5.08 kg)
Processor
Dual ARM1156T2S @ 515 MHz, 4 MB flash, 1 GB compact flash, 512 MB
SDRAM; packet buffer size: 6 MB
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface
mounting only
1000 Mb Latency
< 2.9 µs (FIFO 64-byte packets)
10 Gbps Latency
< 1.3 µs (FIFO 64-byte packets)
Throughput
up to 131 million pps
Switching capacity
176 Gbps
Routing table size
2000 entries (IPv4)
MAC address table size
16000 entries
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), non-condensing
Non-operating/
Storage temperature
-40°F to 158°F (-40°C to 70°C)
Non-operating/
15% to 95% @ 149°F (65°C), non-condensing
Storage relative humidity
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 53.5 dB, Pressure: 39.4 dB; DIN 45635T.19 per ISO 7779
Electrical characteristics Achieved Miercom Certified Green Award
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 7
QuickSpecs
HP 2910 al Switch Series
Technical Specifications
* Products within this series have achieved sufficient scores in each of the rated criteria to achieve the
Miercom Certified Green distinction Award. See the Specifications section of this series for more
information.
Description
The switch automatically adjusts to any voltage between 100-127 and 200240 volts and either 50 or 60 Hz
Maximum heat
356 BTU/hr (376 kJ/hr)
dissipation
Voltage
100-127/200-240 VAC
Current
2.1/1.1 A
Idle power
64 W
Maximum power rating
105 W
Frequency
50/60 Hz
Notes
Safety
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure with
fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
EN 60950/IEC 60950; CAN/CSA 22.2 No. 60950; EN 60825; UL 60950
Emissions
FCC part 15 Class A; EN 55022/CISPR-22 Class A; VCCI Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2; 4 kV CD, 8 kV AD
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV / 2 kV AC, 1 kV signal, 0.5 kV DC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m
Voltage dips and
interruptions
IEC 61000-4-11; > 95% reductions, 0.5 period; 30% reduction, 25 periods
Harmonics
IEC 61000-3-2
Flicker
IEC 61000-3-3
Management
HP PCM+; HP PCM; command-line interface; Web browser; out-of-band management (serial RS-232C)
Notes
When using mini-GBICs with this product, mini-GBICs with revision "B" or later (product number ends with
the letter "B" or later, e.g., J4858B, J4859C) are required.
3-year, 4-hour onsite, 13x5 coverage for hardware (H4496E)
3-year, 4-hour onsite, 24x7 coverage for hardware (H2893E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (U6319E)
3-year, 24x7 SW phone support, software updates (UE264E)
Installation with minimum configuration, system-based pricing (U4826E)
Installation with HP-provided configuration, system-based pricing (U4830E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR884E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR885E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UR886E)
Services
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 8
QuickSpecs
HP 2910 al Switch Series
Technical Specifications
4-year, 24x7 SW phone support, software updates (UR887E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR888E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR889E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UR890E)
5-year, 24x7 SW phone support, software updates (UR891E)
3 Yr 6 hr Call-to-Repair Onsite (UW365E)
4 Yr 6 hr Call-to-Repair Onsite (UW366E)
5 Yr 6 hr Call-to-Repair Onsite (UW367E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR898E)
1-year, 24x7 software phone support, software updates (HR897E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software updates
(HR896E)
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HS618E)
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HS619E)
3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HS620E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS621E)
4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HS622E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS623E)
5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HS624E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS625E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
HP 2910-24G-PoE+ al Switch (J9146A)
Ports
Physical characteristics
20 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE
802.3ab Type 1000BASE-T); Media Type: Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
4 dual-personality ports; each port can be used as either an RJ-45 10/100/1000 port (IEEE 802.3 Type
10Base-T; IEEE 802.3u Type 100Base-TX; IEEE 802.3ab 1000Base-T Gigabit Ethernet) or as a mini-GBIC
slot (for use with mini-GBIC transceivers)
1 RJ-45 serial console port
Supports a maximum of 4 10GbE ports, with optional module
Dimensions
17.4(w) x 14.4(d) x 1.73(h) in (44.2 x 36.58 x 4.39 cm) (1U height)
Weight
Memory and processor
Mounting
Performance
12.34 lb (5.6 kg)
Processor
Dual ARM1156T2S @ 515 MHz, 4 MB flash, 1 GB compact flash, 512 MB
SDRAM; packet buffer size: 6 MB
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface
mounting only
1000 Mb Latency
< 2.9 µs (FIFO)
10 Gbps Latency
< 1.3 µs (FIFO)
Throughput
up to 95 million pps
Switching capacity
128 Gbps
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 9
QuickSpecs
HP 2910 al Switch Series
Technical Specifications
Environment
Routing table size
2000 entries (IPv4)
MAC address table size
16000 entries
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), non-condensing
Non-operating/
Storage temperature
-40°F to 158°F (-40°C to 70°C)
Non-operating/
15% to 95% @ 149°F (65°C), non-condensing
Storage relative humidity
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 51.5 dB, Pressure: 38.1 dB; DIN 45635T.19 per ISO 7779
Electrical characteristics Description
Maximum heat
dissipation
The switch automatically adjusts to any voltage between 100-127 and 200240 volts and either 50 or 60 Hz
447 BTU/hr (472 kJ/hr), max. using PoE+
Voltage
100-127/200-240 VAC
Current
6.1/3.1 A
Idle power
65 W
Maximum power rating
490 W
PoE power
382 W
Frequency
50/60 Hz
Notes
Safety
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure with
fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
PoE Power is the power supplied by the internal power supply, it is dependent
on the type and quantity of power supplies and may be supplemented with the
use of a External Power Supply (EPS).
EN 60950/IEC 60950; CAN/CSA 22.2 No. 60950; EN 60825; UL 60950
Emissions
FCC part 15 Class A; EN 55022/CISPR-22 Class A; VCCI Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2; 4 kV CD, 8 kV AD
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV / 2 kV AC, 1 kV signal, 0.5 kV DC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m
Voltage dips and
interruptions
IEC 61000-4-11; > 95% reductions, 0.5 period; 30% reduction, 25 periods
Harmonics
IEC 61000-3-2
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 10
QuickSpecs
HP 2910 al Switch Series
Technical Specifications
Flicker
IEC 61000-3-3
Management
HP PCM+; HP PCM; command-line interface; Web browser; out-of-band management (serial RS-232C)
Notes
When using mini-GBICs with this product, mini-GBICs with revision "B" or later (product number ends with
the letter "B" or later, e.g., J4858B, J4859C) are required.
3-year, 4-hour onsite, 13x5 coverage for hardware (U2855E)
3-year, 4-hour onsite, 24x7 coverage for hardware (U2856E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (U6304E)
3-year, 24x7 SW phone support, software updates (UE262E)
Installation with minimum configuration, system-based pricing (U4826E)
Installation with HP-provided configuration, system-based pricing (U4830E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR868E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR869E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UR870E)
4-year, 24x7 SW phone support, software updates (UR871E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR872E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR873E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UR874E)
5-year, 24x7 SW phone support, software updates (UR875E)
3 Yr 6 hr Call-to-Repair Onsite (UW356E)
4 Yr 6 hr Call-to-Repair Onsite (UW357E)
5 Yr 6 hr Call-to-Repair Onsite (UW358E)
-year, 6 hour Call-To-Repair Onsite for hardware (HR893E)
1-year, 24x7 software phone support, software updates (HR892E)
1-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HS610E)
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HS611E)
3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HS612E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS613E)
4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HS614E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS615E)
5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HS616E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS617E)
Services
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
HP 2910-48G-PoE+ al Switch (J9148A)
Ports
44 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE
802.3ab Type 1000BASE-T); Media Type: Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
4 dual-personality ports; each port can be used as either an RJ-45 10/100/1000 port (IEEE 802.3 Type
10Base-T; IEEE 802.3u Type 100Base-TX; IEEE 802.3ab 1000Base-T Gigabit Ethernet) or as a mini-GBIC
slot (for use with mini-GBIC transceivers)
1 RJ-45 serial console port
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 11
QuickSpecs
HP 2910 al Switch Series
Technical Specifications
Physical characteristics
Supports a maximum of 4 10GbE ports, with optional module
Dimensions
17.42(w) x 14.4(d) x 1.73(h) in (44.25 x 36.58 x 4.39 cm) (1U height)
Weight
Memory and processor
Mounting
Performance
Environment
12.96 lb (5.88 kg)
Processor
Dual ARM1156T2S @ 515 MHz, 4 MB flash, 1 GB compact flash, 512 MB
SDRAM; packet buffer size: 6 MB
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface
mounting only
1000 Mb Latency
< 2.9 µs (FIFO)
10 Gbps Latency
< 1.3 µs (FIFO)
Throughput
up to 131 million pps
Switching capacity
176 Gbps
Routing table size
2000 entries (IPv4)
MAC address table size
16000 entries
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), non-condensing
Non-operating/
Storage temperature
-40°F to 158°F (-40°C to 70°C)
Non-operating/
15% to 95% @ 149°F (65°C), non-condensing
Storage relative humidity
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 51.5 dB, Pressure: 38.1 dB; DIN 45635T.19 per ISO 7779
Electrical characteristics Description
Maximum heat
dissipation
The switch automatically adjusts to any voltage between 100-127 and 200240 volts and either 50 or 60 Hz
667 BTU/hr (704 kJ/hr), max. using PoE+
Voltage
100-127/200-240 VAC
Current
6.4/3.2 A
Idle power
89 W
Maximum power rating
556 W
PoE power
382 W
Frequency
50/60 Hz
Notes
Safety
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure with
fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
PoE Power is the power supplied by the internal power supply, it is dependent
on the type and quantity of power supplies and may be supplemented with the
use of a External Power Supply (EPS).
EN 60950/IEC 60950; CAN/CSA 22.2 No. 60950; EN 60825; UL 60950
Emissions
FCC part 15 Class A; EN 55022/CISPR-22 Class A; VCCI Class A
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 12
QuickSpecs
HP 2910 al Switch Series
Technical Specifications
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2; 4 kV CD, 8 kV AD
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV / 2 kV AC, 1 kV signal, 0.5 kV DC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m
Voltage dips and
interruptions
IEC 61000-4-11; > 95% reductions, 0.5 period; 30% reduction, 25 periods
Harmonics
IEC 61000-3-2
Flicker
IEC 61000-3-3
Management
HP PCM+; HP PCM; command-line interface; Web browser; out-of-band management (serial RS-232C)
Notes
When using mini-GBICs with this product, mini-GBICs with revision "B" or later (product number ends with
the letter "B" or later, e.g., J4858B, J4859C) are required.
3-year, 4-hour onsite, 13x5 coverage for hardware (H4496E)
3-year, 4-hour onsite, 24x7 coverage for hardware (H2893E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (U6319E)
3-year, 24x7 SW phone support, software updates (UE264E)
Installation with minimum configuration, system-based pricing (U4826E)
Installation with HP-provided configuration, system-based pricing (U4830E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR884E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR885E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UR886E)
4-year, 24x7 SW phone support, software updates (UR887E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR888E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR889E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UR890E)
5-year, 24x7 SW phone support, software updates (UR891E)
3 Yr 6 hr Call-to-Repair Onsite (UW365E)
4 Yr 6 hr Call-to-Repair Onsite (UW366E)
5 Yr 6 hr Call-to-Repair Onsite (UW367E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR898E)
1-year, 24x7 software phone support, software updates (HR897E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software updates
(HR896E)
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HS618E)
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HS619E)
3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HS620E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS621E)
4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HS622E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS623E)
5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HS624E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS625E)
Services
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 13
QuickSpecs
HP 2910 al Switch Series
Technical Specifications
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
Standards and protocols
(applies to all products in
series)
Device management
RFC 1591 DNS (client)
HTML and telnet management
General protocols
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1v VLAN classification by Protocol and
Port
IEEE 802.1w Rapid Reconfiguration of Spanning
Tree
IEEE 802.3ad Link Aggregation Control Protocol
(LACP)
IEEE 802.3x Flow Control
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 868 Time Protocol
RFC 951 BOOTP
RFC 1058 RIPv1
RFC 1350 TFTP Protocol (revision 2)
RFC 2030 Simple Network Time Protocol (SNTP) v4
RFC 2131 DHCP
RFC 2453 RIPv2
RFC 3046 DHCP Relay Agent Information Option
IP multicast
RFC 3376 IGMPv3 (host joins only)
IPv6
RFC 1981 IPv6 Path MTU Discovery
RFC 2460 IPv6 Specification
RFC 2710 Multicast Listener Discovery (MLD) for
IPv6
RFC 2925 Remote Operations MIB (Ping only)
RFC 3019 MLDv1 MIB
RFC 3315 DHCPv6 (client only)
RFC 3513 IPv6 Addressing Architecture
RFC 3596 DNS Extension for IPv6
RFC 3810 MLDv2 (host joins only)
RFC 4022 MIB for TCP
RFC 4113 MIB for UDP
RFC 4251 SSHv6 Architecture
MIBs
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 1724 RIPv2 MIB
RFC 2021 RMONv2 MIB
RFC 2613 SMON MIB
RFC 2618 RADIUS Client MIB
RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2737 Entity MIB (Version 2)
RFC 2863 The Interfaces Group MIB
RFC 2925 Ping MIB
Network management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 2819 Four groups of RMON: 1 (statistics), 2
(history), 3 (alarm) and 9 (events)
RFC 3176 sFlow
ANSI/TIA-1057 LLDP Media Endpoint Discovery
(LLDP-MED)
SNMPv1/v2c/v3
XRMON
QoS/CoS
RFC 2474 DiffServ Precedence, including 8
queues/port
RFC 2597 DiffServ Assured Forwarding (AF)
RFC 2598 DiffServ Expedited Forwarding (EF)
Ingress Rate Limiting
Security
IEEE 802.1X Port Based Network Access Control
RFC 1492 TACACS+
RFC 2138 RADIUS Authentication
RFC 2866 RADIUS Accounting
Secure Sockets Layer (SSL)
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 14
QuickSpecs
HP 2910 al Switch Series
Technical Specifications
RFC 4252 SSHv6 Authentication
RFC 4253 SSHv6 Transport Layer
RFC 4254 SSHv6 Connection
RFC 4293 MIB for IP
RFC 4419 Key Exchange for SSH
RFC 4443 ICMPv6
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Auto-configuration
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 15
QuickSpecs
HP 2910 al Switch Series
Accessories
HP 2910 al Switch Series
accessories
Modules
HP 2-port 10GbE CX4 al Module
HP 2-port 10GbE SFP+ al Module
HP 10-GbE al Switch Interconnect Kit
Transceivers
J9149A
J9008A
J9165A
HP X111 100M SFP LC FX Transceiver
HP X112 100M SFP LC BX-D Transceiver
HP X112 100M SFP LC BX-U Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X132 10G SFP+ LC LR Transceiver
J9054C
J9099B
J9100B
J9150A
J9151A
HP X132 10G SFP+ LC LRM Transceiver
HP X132 10G SFP+ LC ER Transceiver
HP X121 1G SFP LC LH Transceiver
HP X121 1G SFP LC SX Transceiver
HP X121 1G SFP LC LX Transceiver
HP X122 1G SFP LC BX-D Transceiver
HP X122 1G SFP LC BX-U Transceiver
Cables
J9152A
J9153A
J4860C
J4858C
J4859C
J9142B
J9143B
HP X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 10m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 15m Direct Attach Copper Cable
HP 0.5 m Multimode OM3 LC/LC Optical Cable
HP 1 m Multimode OM3 LC/LC Optical Cable
HP 2 m Multimode OM3 LC/LC Optical Cable
HP 5 m Multimode OM3 LC/LC Optical Cable
HP 15 m Multimode OM3 LC/LC Optical Cable
HP 30 m Multimode OM3 LC/LC Optical Cable
HP 50 m Multimode OM3 LC/LC Optical Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable
HP BLc SFP+ 0.5m 10GbE Copper Cable
HP BLc SFP+ 1m 10GbE Copper Cable
HP BLc SFP+ 3m 10GbE Copper Cable
HP BLc SFP+ 5m 10GbE Copper Cable
DA - 13280 Worldwide — Version 18 — June 10, 2013
J9281B
J9283B
J9285B
J9286B
J9287B
AJ833A
AJ834A
AJ835A
AJ836A
AJ837A
AJ838A
AJ839A
QK732A
QK733A
QK734A
QK735A
QK736A
QK737A
487649-B21
487652-B21
487655-B21
537963-B21
Page 16
QuickSpecs
HP 2910 al Switch Series
Accessories
HP BLc SFP+ 7m 10GbE Copper Cable
EPS/RPS
487658-B21
HP 620 Redundant/External Power Supply
HP 630 Redundant and/or External Power Supply
Mounting Kit
J8696A
J9443A
HP X410 1U Universal 4-post Rack Mounting Kit
J9583A
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 17
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
NOTE: Details are not available for all accessories. The following specifications were available at the time of publication.
HP 2-port 10GbE CX4 al
Module (J9149A)
Ports
2 CX4 10-GbE ports (IEEE 802.3ak Type 10GBASE-CX4); Duplex: full only
Physical characteristics
Dimensions
Environment
Cabling
Operating temperature
32°F to 122°F (0°C to 50°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 95% @ 149°F (65°C), noncondensing
Maximum distance:
• 15 m using CX4 cable
• 300 m using optical media converters and multimode fiber cable
Use CX4 10-GbE cable (0.5 m-15 m) or HP ProCurve 10-GbE CX4 Media
Converter (J8439A). No CX4 cables are included with this module.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Notes
Services
HP 2-port 10GbE SFP+ al
Module (J9008A)
Weight
4.11(d) x 4.18(w) x 1.4(h) in. (10.44 x 10.62 x 3.56
cm)
0.35 lb. (0.16 kg)
Ports
2 open 10-GbE SFP+ transceiver slots
Physical characteristics
Dimensions
Environment
Services
Weight
4.0(d) x 4.18(w) x 1.4(h) in. (10.16 x 10.62 x 3.56
cm)
0.35 lb. (0.16 kg)
Operating temperature
32°F to 122°F (0°C to 50°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 95% @ 149°F (65°C), noncondensing
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 18
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP 10GbE al Switch
Physical characteristics
Interconnect Kit (J9165A)
Environment
Notes
Weight
4.11(d) x 4.18(w) x 1.4(h) in. (10.44 x 10.62 x 3.56
cm)
0.31 lb. (0.14 kg)
Operating temperature
32°F to 122°F (0°C to 50°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 95% @ 149°F (65°C), noncondensing
ProCurve Switch bl 10-GbE Interconnect Kit includes two 1-port 10-GbE CX4
compatible Interconnect modules for short-distance connectivity using the
0.5 m CX4 cable provided.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
HP X111 100M SFP LC FX
Transceiver (J9054C)
Dimensions
Ports
1 LC 100BASE-FX port (IEEE 802.3u Type 100BASE-FX); Duplex: half or full
Physical characteristics
Dimensions
Environment
Cabling
Notes
Services
Weight
2.7(d) x 0.54(w) x 0.48(h) in. (6.86 x 1.38 x 1.22
cm)
0.06 lb. (0.03 kg)
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
5% to 95%
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Nonoperating/Storage
relative humidity
5% to 85%
Altitude
up to 10,000 ft. (3 km)
Cable type:
62.5/125 ìm or 50/125 ìm (core/cladding) diameter, graded-index, low metal
content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2
Type A1b or A1a, respectively;
Maximum distance:
• 2 km (full duplex) or 412 m (half duplex)
Transmitter wavelength: 1310nm
Power consumption is 1.1 watt maximum.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the J9054B 100-FX SFP-LC
Transceiver" on the "ProCurve Mini-GBICs and SFPs" Manuals Web page.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 19
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP X112 100M SFP LC BX-D Ports
Transceiver (J9099B)
Physical characteristics
A small form-factor
pluggable (SFP) 100Megabit BX (bi-directional)
"downstream" transceiver Environment
that provides 100 Mbps
full-duplex connectivity up
to 10 km on one strand of
singlemode fiber. The
J9099B connects to the
Cabling
J9100B "upstream"
transceiver, or to any IEEEstandard 100BASE-BX10-U
("upstream") device.
1 LC 100BASE-BX10 port (IEEE 802.3ah Type 100BASE-BX10-D); Duplex: full
only
Dimensions
2.7(d) x 0.55(w) x 0.48(h) in. (6.86 x 1.39 x 1.22
cm)
Weight
0.04 lb. (0.03 kg)
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, noncondensing
Nonoperating/Storage
temperature
-40ºF to 185ºF (-40ºC to 85ºC)
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
0.5-10,000 m (single-mode fiber)
Transmit wavelength: 1550 nm. Receive wavelength: 1310 nm.
Power consumption is 1.1 watt maximum.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9099B connects to the J9100B "upstream" transceiver, or to any IEEEstandard 100BASE-BX10-U ("upstream") device. (A 100-BX-D transceiver can
only connect to a 100-BX-U product. You cannot connect two 100-BX-D
transceivers together.)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Notes
Services
HP X112 100M SFP LC BX-U Ports
Transceiver (J9100B)
Physical characteristics
A small form-factor
pluggable (SFP) 100Megabit BX (bi-directional)
Environment
"upstream" transceiver
that provides 100 Mbps
full-duplex connectivity up
to 10 km on one strand of
singlemode fiber. The
J9100B connects to the
Cabling
J9099B "downstream"
transceiver, or to any IEEEstandard 100BASE-BX10-D
("downstream")
device.
1 LC 100BASE-BX10 port (IEEE 802.3ah Type 100BASE-BX10-U); Duplex: full
only
Dimensions
2.7(d) x 0.55(w) x 0.48(h) in. (6.86 x 1.39 x 1.22
cm)
Weight
0.07 lb. (.03 kg)
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, noncondensing
Nonoperating/Storage
temperature
-40ºF to 185ºF (-40ºC to 85ºC)
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
0.5-10,000 m (single-mode fiber)
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 20
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
Notes
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9100B connects to the J9099B "downstream" transceiver, or to any IEEEstandard 100BASE-BX10- D ("downstream") device. (A 100-BX-U transceiver
can only connect to a 100-BX-D product. You cannot connect two 100-BX-U
transceivers together.)
Transmit wavelength: 1310 nm. Receive wavelength: 1550 nm.
Power consumption is 1.1 watts maximum.
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
HP X132 10G SFP+ LC SR
Transceiver (J9150A)
Ports
1 LC 10-GbE port (IEEE 802.3ae Type 10Gbase-SR); Duplex: full only
Connectivity
Connector type
LC
Wavelength
850 nm
Dimensions
Weight
2.19(d) x 0.54(w) x 0.47(h) in. (5.57 x 1.38 x 1.19
cm)
0.04 lb. (0.02 kg)
Transceiver form factor
SFP+
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
0% to 85%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Altitude
up to 10,000 ft. (3 km)
A 10-Gigabit transceiver in
Physical characteristics
SFP+ form-factor that
supports the 10-Gigabit SR
standard, providing 10Gigabit connectivity up to
300 m on multimode fiber.
Environment
Electrical characteristics Power consumption
typical
0.6 W
Power consumption
maximum
0.8 W
Cabling
Cable type:
62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal
content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2
Type A1b or A1a, respectively;
Maximum distance:
2-26m with 62.5 µm multimode cable @ 160 MHz*km
2-33m with 62.5 µm multimode cable @ 200 MHz*km
2-66m with 50 µm multimode cable @ 400 MHz*km
2-82m with 50 µm multimode cable @ 500 MHz*km
2-300m with 50 µm multimode cable @ 2000 MHz*km
Cable length
2-300m
Fiber type
Notes
Multi Mode
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 21
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP X132 10G SFP+ LC LR
Transceiver (J9151A)
Services
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
1 LC 10-GbE port (IEEE 802.3ae Type 10Gbase-LR); Duplex: full only
Connectivity
Connector type
LC
Wavelength
1310 nm
Dimensions
Weight
2.19(d) x 0.54(w) x 0.47(h) in. (5.57 x 1.38 x 1.19
cm)
0.04 lb. (.02 kg)
Transceiver form factor
SFP+
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
0% to 85%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Altitude
up to 10,000 ft. (3 km)
A 10-Gigabit transceiver in
Physical characteristics
SFP+ form-factor that
supports the 10-Gigabit LR
standard, providing 10Gigabit connectivity up to
10 km on single-mode
Environment
fiber.
Electrical characteristics Power consumption
typical
Power consumption
maximum
Cabling
0.9 W
1W
Cable type:
Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and
ISO/IEC 793-2 Type B1;
Maximum distance:
2m-10km with 9/125 µm single-mode cable
Cable length
2m to 10km
Fiber type
Notes
Services
Single Mode
Conditioning patch cord cables are not supported.
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 22
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP X132 10G SFP+ LC LRM Ports
Transceiver (J9152A)
Connectivity
1 LC 10-GbE port (IEEE 802.3aq Type 10Gbase-LRM); Duplex: full only
Connector type
LC
A 10-Gigabit transceiver in
Physical characteristics
SFP+ form-factor that
supports the 10-Gigabit
LRM standard, for 10Gigabit connectivity up to
220 m on legacy
Environment
multimode fiber.
Wavelength
1310 nm
Dimensions
Weight
2.19(d) x 0.54(w) x 0.47(h) in. (5.57 x 1.38 x 1.19
cm)
0.04 lb. (.02 kg)
Transceiver form factor
SFP+
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
0% to 85%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics Power consumption
typical
Power consumption
maximum
Cabling
0.7 W
1W
Cable type:
62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal
content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2
Type A1b or A1a, respectively (a mode conditioning patch cord may be needed
in some multimode fiber installations);
Maximum distance:
0.5-220m with 62.5 µm multimode cable @ 160/500 MHz*km
0.5-220m with 62.5 µm multimode cable @ 200/500 MHz*km
0.5-100m with 50 µm multimode cable @ 400/400 MHz*km
0.5-220m with 50 µm multimode cable @ 500/500 MHz*km
0.5-220m with 50 µm multimode cable @ 1500/500 MHz*km
Cable length
0.5m to 220m
Fiber type
Notes
Services
Multi Mode
For OM3 cable (50 µm multimode @ 1500/500 MHz*km), a mode-conditioning
patch cord is not required. Other multimode cables may require modeconditioning patch cords to achieve the maximum distances listed above.
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 23
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP X121 1G SFP LC LH
Transceiver (J4860C)
Ports
Physical characteristics
A small form-factor
pluggable (SFP) Gigabit LH Environment
transceiver that provides a
full-duplex Gigabit solution
up to 70 km on singlemode fiber.
Cabling
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics); Duplex:
full only
Dimensions: 2.17(d) x 0.60(w) x 0.46(h) in. (5.5 x 1.53 x 1.18 cm)
Weight: 0.04 lb. (0.02 kg)
Operating temperature: -40°F to 185°F (-40°C to 85°C)
Operating relative humidity: 0% to 95% @ 77°F (25°C), noncondensing
Nonoperating/Storage temperature: -40°F to 185°F (-40°C to 85°C)
Altitude: up to 10,000 ft. (3 km)
Cable type:
Low metal content, single-mode fiber-optic, complying with ITU-T
G.652 and ISO/IEC 793-2 Type B1;
Maximum distance:
10-70,000 m (single-mode fiber)
Power consumption is 0.8 watts typical with 1 watt maximum at 100%
utilization.
For distances less than 20 km, a 10 dB attenuator must be used.
For distances between 20 km and 40 km, a 5 dB attenuator must be used.
Attenuators can be purchased from most cable vendors.
Refer to the HP website at www.hp.com/networking/services for details on the
service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local HP sales office.
Notes
Services
HP X121 1G SFP LC SX
Transceiver (J4858C)
A small form-factor
pluggable (SFP) Gigabit SX
transceiver that provides a
full-duplex Gigabit solution
up to 550 m on multimode
fiber.
Ports
Physical characteristics
1 LC 1000BASE-SX port; Duplex: full only
Dimensions: 2.24(d) x 0.54(w) x 0.48(h) in. (5.69 x 1.37 x 1.22 cm)
Weight: 0.04 lb. (0.02 kg)
Transceiver form factor: SFP
Environment
Operating temperature: 32°F to 158°F (0°C to 70°C)
Operating relative humidity: 5% to 85%, noncondensing
Nonoperating/Storage temperature: -40°F to 203°F (-40°C to 85°C)
Altitude: up to 10,000 ft. (3 km)
Electrical characteristics Power consumption typical: 0.4 W
Power consumption maximum: 0.7 W
Cabling
Type:
62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low
metal content, multimode fiber optic, complying with ITU-T G.651 and
ISO/IEC 793-2 Type A1b or A1a, respectively;
Maximum distance:
2-220 m (62.5 µm core diameter, 160 MHz*km bandwidth
2-275 m (62.5 µm core diameter, 200 MHz*km bandwidth
2-500 m (50 µm core diameter, 400 MHz*km bandwidth)
2-550 m (50 µm core diameter, 500 MHz*km bandwidth)
Cable length: 2-550m
Fiber type: Multi Mode
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 24
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP X121 1G SFP LC LX
Transceiver (J4859C)
Services
Refer to the HP website at www.hp.com/networking/services for details on the
service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local HP sales office.
Ports
Physical characteristics
1 LC 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX); Duplex: full only
Dimensions: 2.24(d) x 0.54(w) x 0.486(h) in. (5.69 x 1.37 x 1.23 cm)
Weight:0.04 lb. (0.02 kg)
Operating temperature: 32°F to 158°F (0°C to 70°C)
Operating relative humidity: 0% to 85%, noncondensing
Nonoperating/Storage temperature: -40°F to 212°F (-40°C to 100°C)
Altitude: up to 10,000 ft. (3 km)
Type:
HP X121 1G SFP LC LX
Environment
Transceiver: An SFP format
gigabit transceiver with LC
connectors using LX
technology.
Cabling
Either single mode or multimode; 62.5/125 µm or 50/125 µm
(core/cladding) diameter, graded-index, low metal content, multimode
fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or
A1a, respectively; Low metal content, single-mode fiber-optic,
complying with ITU-T G.652 and ISO/IEC 793-2 Type B1;
Maximum distance:
Notes
Services
2-550 m (multimode 62.5 µm core diameter, 500 MHz*km bandwidth)
2-550 m (multimode 50 µm core diameter, 400 MHz*km bandwidth)
2-550 m (multimode 50 µm core diameter, 500 MHz*km bandwidth)
2-10,000 m (single-mode fiber)
A mode conditioning patch cord may be needed in some multimode fiber
installations.
Wavelength: 1310nm
Power Consumption: < 500mW Typical
Refer to the HP website at www.hp.com/networking/services for details on the
service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 25
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP X122 1G SFP LC BX-D
Transceiver (J9142B)
Ports
Physical characteristics
A small form-factor
pluggable (SFP) Gigabit-BX
(bi-directional)
"downstream" transceiver Environment
that provides a full-duplex
Gigabit solution up to 10
km on one strand of
single-mode fiber. The
J9142B connects to the
Cabling
J9143B "upstream"
transceiver, or to any IEEEstandard 1000BASE-BX10U ("upstream") device.
Services
Ports
Physical characteristics
A small form-factor
pluggable (SFP) Gigabit-BX
(bi-directional) "upstream"
transceiver that provides a Environment
full-duplex Gigabit solution
up to 10 km on one strand
of single-mode fiber. The
J9143B connects to the
J9142B "downstream"
transceiver, or to any IEEE- Cabling
standard 1000BASE-BX10D ("downstream")
device.
Notes
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, non-condensing
Non-operating/
Storage temperature
–40ºF to 185ºF –40ºC to 85ºC)
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
0.5-10,000 m (single-mode fiber)
Transmit wavelength: 1490 nm. Receive wavelength: 1310 nm.
Power consumption is 1 watt maximum.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9142B connects to the J9143B "upstream" transceiver, or to any IEEEstandard 1000BASE-BX10-U ("upstream") device. (A 1000-BX-D transceiver
can only connect to a 1000-BX-U product. You cannot connect two 1000-BX-D
transceivers together.)
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Notes
HP X122 1G SFP LC BX-U
Transceiver (J9143B)
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-D); Duplex:
full only
Dimensions
2.19(d) x 0.54(w) x 0.46(h) in. (5.57 x 1.37 x 1.18
cm)
Weight
0.04 lb. (0.02 kg)
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-U); Duplex:
full only
Dimensions
2.19(d) x 0.54(w) x 0.46(h) in. (5.57 x 1.37 x 1.18
cm)
Weight
0.04 lb. (0.02 kg)
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, non-condensing
Non-operating/
Storage temperature
–40ºF to 185ºF –40ºC to 85ºC)
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
0.5-10,000 m (single-mode fiber)
Transmit wavelength: 1310 nm. Receive wavelength: 1490 nm.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 26
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9143B connects to the J9142B "downstream" transceiver, or to any IEEEstandard 1000BASE-BX10-D ("downstream") device. (A 1000-BX-U
transceiver can only connect to a 1000-BX-D product. You cannot connect two
1000-BX-U transceivers together.)
Power consumption is 1 watt maximum.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
HP X242 SFP+ SFP+ 1 m
Direct Attach Cable
(J9281B)
Connectivity
Length
3.28 ft. (1 m)
Physical characteristics
Weight
0.24 lb. (0.11 kg) the cable with an SFP+
transceiver at each end of the cable
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
Services
14ºF to 185ºF (-10ºC to 85ºC)
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 27
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP X242 SFP+ SFP+ 3 m
Direct Attach Cable
(J9283B)
Connectivity
Length
10 ft. (3 m)
Physical characteristics
Weight
.49 lb. (0.22 kg), Fully loaded the cable with an
SFP+ transceiver at each end of the cable
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
HP X242 SFP+ SFP+ 7 m
Direct Attach Cable
(J9285B)
14ºF to 185ºF (-10ºC to 85ºC)
Connectivity
Length
22.97 ft. (7 m)
Physical characteristics
Weight
1.02 lb., Fully loaded the cable with an SFP+
transceiver at each end of the cable
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
14ºF to 185ºF (-10ºC to 85ºC)
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 28
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
Services
HP 0.5 m Multimode OM3 Cabling
LC/LC Optical Cable
(AJ833A)
Notes
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical glass: Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical glass: Bandwidth: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: 600 / 600 meters @850/1300nm
for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber and designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 29
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP 1 m Multimode OM3
LC/LC Optical Cable
(AJ834A)
Cabling
Notes
Services
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 30
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP 2 m Multimode OM3
LC/LC Optical Cable
(AJ835A)
Cabling
Notes
Services
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 31
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP 5 m Multimode OM3
LC/LC Optical Cable
(AJ836A)
Cabling
Notes
Services
Cable type:
50/125 µm core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: This specification defines the detail requirements for a tight
buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and
Ethernet assembly with LC duplex connectors on one end and LC duplex
connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 32
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP 15 m Multimode OM3
LC/LC Optical Cable
(AJ837A)
Cabling
Notes
Services
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 33
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP 30 m Multimode OM3
LC/LC Optical Cable
(AJ838A)
Cabling
Notes
Services
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 34
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP 50 m Multimode OM3
LC/LC Optical Cable
(AJ839A)
Cabling
Notes
Services
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 35
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
1m Cable (QK732A)
Notes
Services
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
2m Cable (QK733A)
Notes
Services
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core Diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 36
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
5m Cable (QK734A)
Notes
Services
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
15m Cable (QK735A)
Notes
Services
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 37
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
30m Cable (QK736A)
Notes
Services
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
50m Cable (QK737A)
Notes
Services
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 38
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP BLc SFP+ 0.5m 10GbE
Copper Cable (487649B21)
Connectivity
Length
1.64 ft. (0.5 m)
Physical characteristics
Weight
.18 lb. (0.08 kg) the cable with an SFP+
transceiver at each end of the cable
32°F to 158°F (0°C to 70°C)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
HP BLc SFP+ 1m 10GbE
Copper Cable (487652B21)
14°F to 185°F (-10°C to 85°C)
Connectivity
Length
3.28 ft. (1 m)
Physical characteristics
Weight
.24 lb. (0.11 kg) the cable with an SFP+
transceiver at each end of the cable
32°F to 158°F (0°C to 70°C)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
Services
14°F to 185°F (-10°C to 85°C)
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 39
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP BLc SFP+ 3m 10GbE
Copper Cable (487655B21)
Connectivity
Length
9.84 ft. (3 m)
Physical characteristics
Weight
0.49 lb. (0.22 kg) the cable with an SFP+
transceiver at each end of the cable
32°F to 158°F (0°C to 70°C)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
HP BLc SFP+ 5m 10GbE
Copper Cable (537963B21)
14°F to 185°F (-10°C to 85°C)
Connectivity
Length
16.40 ft. (5 m)
Physical characteristics
Weight
0.75 lb. (0.34 kg) the cable with an SFP+
transceiver at each end of the cable
32°F to 158°F (0°C to 70°C)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
14°F to 185°F (-10°C to 85°C)
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 40
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
HP BLc SFP+ 7m 10GbE
Copper Cable (487658B21)
Services
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Connectivity
Length
22.96 ft. (7 m)
Physical characteristics
Weight
1.01 lb. (0.46 kg) the cable with an SFP+
transceiver at each end of the cable
32°F to 158°F (0°C to 70°C)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
HP 620
Redundant/External
Power Supply (J8696A)
14°F to 185°F (-10°C to 85°C)
Ports
2 redundant power supply ports
Restrictions: 195 W available per port
Physical characteristics
Mounting
Environment
2 external power supply ports
Restrictions: 398 W available per port
Dimensions
15.4(d) x 17.4(w) x 1.73(h) in. (39.12 x 44.2 x 4.39
cm) (1U height)
Weight
15.2 lb. (6.89 kg)
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
included); horizontal surface mounting only
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 41
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
Altitude
up to 10,000 ft. (3 km)
Acoustic
LwA per ISO 7779: 54.2 dB
Electrical characteristics Maximum heat
dissipation
Voltage
400 BTU/hr (422 kJ/hr), for the actual 620 itself.
PoE-powered device heat dissipation assumed to
be outside the 620.
100-127/200-240 VAC
Current
16/8 A
Maximum power rating
1440 W
RPS power
390 W
PoE power
796 W
RPS
12 V
PoE
-50 V
Frequency
50/60 Hz
Notes
Safety
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped),
100% traffic, all ports plugged in, and all modules
populated.
Above figures are for maximum RPS and PoE
power being supplied to two switches
simultaneously. 200 - 240 V power cords shipped
with the 620 have a wall plug rated as close to 13
A as specific country standards allow.
CSA 22.2 No. 60950; EN 60950/IEC 60950; UL 60950
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3
EFT/Burst
IEC 61000-4-4
Surge
IEC 61000-4-5
Conducted
IEC 61000-4-6
Power frequency
magnetic field
IEC 61000-4-8
Voltage dips and
interruptions
IEC 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
Unmanaged power supply; provides information via LEDs (LEDs repeated on
front and back panel) or through port interfaces of attached devices
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 42
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
Notes
The 620 supports the HP Switch 2900 Series (RPS) and 3500yl Series
(RPS/PoE), as well as 6200yl (RPS) switches. The HP Switch 5400zl Series is
not supported.
The 620 includes four 2 m RPS/EPS cables. These cables can be used to carry
either RPS or PoE power to the switch being powered.
3-year, 4-hour onsite, 13x5 coverage for hardware (U9270E)
3-year, 4-hour onsite, 24x7 coverage for hardware (U9271E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR854E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR855E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR857E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR858E)
3 Yr 6 hr Call-to-Repair Onsite (UW371E)
4 Yr 6 hr Call-to-Repair Onsite (UW372E)
5 Yr 6 hr Call-to-Repair Onsite (UW373E)
Services
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 630 Redundant and/or Physical characteristics
External Power Supply
(J9443A)
Environment
Dimensions
Weight
15(d) x 8.5(w) x 1.73(h) in. (38.1 x 21.59 x 4.39
cm) (1U height)
7.9 lb. (3.58 kg)
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 10,000 ft. (3 km)
Acoustic
Power: 54.2 dB; ISO 7779, ISO 9296
Electrical characteristics Maximum heat
dissipation
Voltage
535 BTU/hr (564.42 kJ/hr), for the actual 630
power supply. PoE-powered device heat
dissipation assumed to be outside the 630 power
supply.
100-127/200-240 VAC
Current
8/4 A
Maximum power rating
740 W
PoE power
398 W
RPS power
185 W
PoE power
398 W
Frequency
50/60 Hz
Notes
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 43
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
infrastructure with fully loaded PoE (if equipped),
100% traffic, all ports plugged in, and all modules
populated.
PoE Power is the power supplied by the internal
power supply, it is dependent on the type and
quantity of power supplies and may be
supplemented with the use of a External Power
Supply (EPS).
200-240 V power cords shipped with the 630
power supply have a wall plug rated as close to 13
A as specific country standards allow.
The HP 630 RPS/EPS supports the HP 2910al and 3500yl-PoE+ Switches. The
HP Switch 5400zl Series is not supported.
The 630 RPS/EPS includes two 2-m RPS/EPS cables, which can bes used to
carry either RPS or PoE+ power to the switch.
Minimum software versions required: 2910al PoE+ switches require W.14.35
or later and 3500yl-PoE+ switches require K.14.52 or later
3-year, 4-hour onsite, 13x5 coverage for hardware (U9270E)
3-year, 4-hour onsite, 24x7 coverage for hardware (U9271E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR854E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR855E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR857E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR858E)
3 Yr 6 hr Call-to-Repair Onsite (UW371E)
4 Yr 6 hr Call-to-Repair Onsite (UW372E)
5 Yr 6 hr Call-to-Repair Onsite (UW373E)
Notes
Services
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X410 1U Universal 4post Rack Mounting Kit
(J9583A)
Notes
The rack mounting kit supports the 1U, full width switches in the following
switch series and the power supply: V1810 Series, E2510 Series, E2520 Series,
E2610 Series, E2810 Series, E2910 Series, E3500 Series, and the E620 Power
Supply
This universal rack mounting kit is design to fit the following racks: HP 10K
10642, HP 10K 10842, Panduit CN, Panduit CS, Wrightline Vantage S2, APC
Netshelter 600mm, and APC Netshelter 800mm. It may well fit many other
brands and models too.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
To learn more, visit: www.hp.com/networking
© Copyright 2008-2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without
notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products
and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial
errors or omissions contained herein.
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 44
QuickSpecs
HP 2910 al Switch Series
Accessory Product Details
DA - 13280 Worldwide — Version 18 — June 10, 2013
Page 45
Download PDF
Similar pages