Clear-Com DX410 Quick Reference Manual

Quick Reference Guide

DX410

6 10

8

1 2 4 3 5 6

3

5

9

1 2 4 7

7 8 9 10

Belt Pack

7

All-In-One Headset

1. Channel A (Intercom 1) button - Includes 2-wire and 4-wire connections

2. ISO (Isolate) button - To All Wireless Headsets and Belt Packs, Base, ISO Relay and AUX OUT

(if activated)

3. Increase Volume button ( ˄ )

4. Decrease Volume button ( ˅ )

5. Channel B (Intercom 2) button - Includes 2-wire and 4-wire connections

1. Battery

2. Increase Volume button ( ▲ )

3. Decrease Volume button ( ▼ )

4. PWR (Power) button

5. Headset cable connector

6. Battery-release latch

7. Power/Mode lights

6. Power/Mode lights

8. Channel A (Intercom 1) button - Includes 2-wire and 4-wire connections

7. Microphone

8. Power button (On/Off)

9. Battery

9. ISO (Isolate) button - To All Wireless Headsets and Belt Packs, Base, ISO Relay and AUX OUT

(if activated)

10. Channel B (Intercom 2) button - Includes 2-wire and 4-wire connections

10. Battery-release latch

Settings & Adjustments

All-In-One Headset Lights Off:

• Make certain the headset power is Off.

• Press and hold the B button while pressing and releasing the Power button.

Note: "Lights Off" is temporary. Lights return when power is cycled.

Belt Pack Sidetone Adjustment:

• Press and hold the A button while you repeatedly press up (▲) to increase or press down (▼) to decrease audio levels.

For technical support

In The Americas and Asia – Tel: +1.510.337.6600 or 1.800.462.4357 Menu option 1 • Hours: 8:00am-5:00pm Pacific Time • Email: [email protected]

In Europe, Middle East and Africa – Tel: +44.1223.815000 • Hours: 8:00am-5:00pm GMT • Email: [email protected]

Copyright © 2015 Clear-Com, LLC, an HM Electronics, Inc. company. All rights reserved.

Clear-Com, the Clear-Com logo and Clear-Com Concert are trademarks or registered trademarks of HM Electronics, Inc.

Part Number: 399G164 Rev A

Date: 12/4/15

Audio Channel and

Auto-Null Controls

Quick Reference Guide

DX410

Local Headset

Controls

COMMUNICATOR ®

Registration

Power Switch

STATUS REG AUTO NULL

Register Belt Pack or All-In-One Headset

• Make certain the Belt Pack or Headset is turned Off.

• Press REG button on base station.

– STATUS display on the base station shows “ o” for registration mode.

• On the Belt Pack and Headset, press and hold ISO while pressing POWER and then release all buttons.

– The power lights blink red, then green and then turn off. One power light remains green.

– The registration number will appear on the base station STATUS display.

AUTO NULL Adjustment (only if using 2-wire interface)

If echo is heard in wireless Belt Packs or All-In-One Headsets on A or B:

• Use pointed object (e.g. pen) to press and hold the A or B AUTO NULL button for 2 seconds.

CAUTION: Before pressing an AUTO NULL button, be certain there are no open microphones on the wired system. Notify wired system users that a loud noise may occur in their headsets during the auto null adjustment.

The system may be out of operation for approximately 50 seconds during this adjustment.

Local Headset Communication

• SEL button selects communication with A, B or ISO.

– A, B or ISO lights indicate selection.

• TALK button

– Press and release quickly to “latch on” for open communication.

– Press and hold while talking for momentary communication – release when finished.

• VOLUME control adjusts the audio level in local headset ear piece.

• MIC LEVEL control adjusts the audio level going out from local headset microphone.