AVR-S700W - DMH Global Home

MODEL: AVR-S700W
Model Information
Index
Front Panel
Rear Panel
Model Information
INTEGRATED NETWORK AV RECEIVER
Remote Control
Warranty
Reset Procedure
Accessories
Protection History
Display Mode
Upgrades/Updates
Product Specifications
I/R Codes
NOTE:
This edition is missing the FAQ’s content (pages 15 and 16) ………………………………………………………..7/1/2015
This edition is missing the link to the IR Codes………………………………………………………………………....7/1/2015
MI070115E3-1
1
Front Panel (1 of 2)
 Power operation button (O)
Used to turn the power of the MAIN ZONE (room where this unit is located)
on/off (standby).
 MASTER VOLUME knob
 Power indicator
This adjusts the volume level.
This is lit as follows according to the power status:
 ZONE2 ON/OFF button
Green: Power on
This turns the power of ZONE2 (separate room) on/off.
Off: Normal standby
Red:
 ZONE2 SOURCE button
oWhen “HDMI Control” is set to “On”
This selects the input source for ZONE2.
oWhen “HDMI Pass Through” is set to “On”
oWhen “Network Control” is set to “Always On”
 SOURCE SELECT knob
This selects the input source.
 Tuner preset channel buttons
(TUNER PRESET CH +, –)
These select preset broadcast stations.
 Remote control sensor

This receives signals from the remote control unit.
Display
Select either FM broadcast or AM broadcast.

Tuning up / Tuning down buttons (TUNE +, –)
This displays various pieces of information.
DISPLAY 1
HOME
FRONT PANEL 2
2
Front Panel (2 of 2)

Reception band select button (BAND)
This switches the reception band.
 SOUND MODE buttons
 Tune mode select button (MODE)
These select the sound mode.
This switches the tuning mode.
QUICK SELECT buttons
With a single press of any of these buttons, you can call up various
settings you’ve registered to each button such as the input source,
volume level and sound mode settings.


DIMMER button
Each press of this switches the brightness of the display.
 STATUS button
 AUX-HDMI connector
Each press of this switches the status information that is shown on the
display.
This is used to connect HDMI output compatible devices such as video
camcorders and game consoles.

Headphones jack (PHONES)
This is used to connect headphones.
When the headphones are plugged into this jack, audio will no longer be
output from the connected speakers or from the SUBWOOFER
connectors.
NOTE:

USB port
This is used to connect USB storages (such as USB memory devices)
and the USB cable supplied with iPod.

To prevent hearing loss, do not raise the volume level excessively when using
headphones.
FRONT PANEL 1
SETUP MIC jack
This is used to connect the supplied Sound calibration microphone.
HOME
DISPLAY 1
3
Display (1 of 2)
 Input mode indicators
 Tuner reception mode indicators
These light according to the audio input mode settings of each input
source.
These light up according to the reception conditions when the input
source is set to “Tuner”.
TUNED: Lights up when the broadcast is properly tuned in.
STEREO: Lights up when receiving FM stereo broadcasts.
 Surround back indicator
This lights when audio signals are being output from the surround back
speakers.
 Sleep timer indicator
This lights when the sleep mode is selected.
 Decoder indicators
These light when Dolby or DTS signals are input or when the Dolby or
DTS decoder is running.
 Audyssey® indicator
 Circle indicator
This is displayed when the input source is “Online Music” or “iPod/USB”
when you are playing back music.
This lights when “MultEQ® XT”, “Dynamic EQ” or “Dynamic Volume”
has been set up.
FRONT PANEL 2
HOME
DISPLAY 2
4
Display (2 of 2)
 Volume indicator
 MUTE indicator
This blinks while the sound is muted.
 Information display
The input source name, sound mode, setting values and other
information are displayed here.
 Input signal indicators
The respective indicator will light corresponding to the input signal.
 ZONE2 indicator
This lights up when ZONE2 (separate room) power is turned on.
DISPLAY 1
HOME
REAR PANEL 1
5
Rear Panel (1 of 2)
 Rod antennas for Bluetooth/wireless LAN
Stand this antenna upright when connecting to a network via wireless
LAN, or when connecting to a handheld device via Bluetooth.
 Analog audio connectors (AUDIO)
Used to connect devices equipped with analog audio connectors.
 PRE OUT connectors
Used to connect a subwoofer with built-in amplifier.

The antenna clip can be removed from the rear panel.
A Rotate the antenna clip 90 degrees to the left.
B Pull the antenna clip out towards yourself.
• The antenna clip is needed when transporting this unit.
Keep it in a safe place.
• Attach the antenna clip by following the steps for
removing it in reverse.
DISPLAY 2
Digital audio connectors (DIGITAL AUDIO)
Used to connect devices equipped with digital audio connectors.
• “Connection 2 : TV equipped with an HDMI connector and incompatible
with the ARC (Audio Return Channel)”
• “Connection 3 : TV equipped without an HDMI connector”
• “Connecting a set-top box (Satellite tuner/cable TV)”

NETWORK connector
Used to connect to a LAN cable when connecting to a wired LAN network.
HOME
REAR PANEL 2
6
Rear Panel (2 of 2)
 HDMI connectors
 FM/AM antenna terminals (ANTENNA)
Used to connect devices equipped with HDMI connectors.
Used to connect FM antennas and AM loop antennas.
 Video connectors (VIDEO)
 Speaker terminals (SPEAKERS)
Used to connect devices equipped with video connectors.
Used to connect speakers.
NOTE
Do not touch the inner pins of the connectors on the rear panel. Electrostatic
discharge may cause permanent damage to the unit.
 Power cord
Used to connect the power cord.
REAR PANEL 1
HOME
Remote Control 1
7
Remote Control (1 of 3)
 ZONE2 ON/OFF button (ZONE2 O)
This turns the power of ZONE2 (separate room) on/off.
 ZONE2 VOLUME buttons ()
This setting adjusts the volume level for ZONE2.
 ZONE2 SOURCE button
This selects the input source for ZONE2.
 Input source select buttons
These selects the input source.
 SOUND MODE buttons
These select the sound mode.
• MOVIE button
• MUSIC button
• GAME button
• PURE button
 Information button (INFO)
This displays the status information on the TV screen.
 Cursor buttons ()
These select items.
 ENTER button
This determines the selection.
REAR PANEL 2
HOME
REMOTE CONTROL 2
8
Remote Control (2 of 3)
 BACK button
This returns to the previous screen.
 System buttons
These perform playback related operations.
• Skip buttons (,)
• Play/pause button (/II)
Tuning up / Tuning down buttons (TUNE +, –)
These select either FM broadcast or AM broadcast.
 QUICK SELECT buttons (1 – 4)
These call up settings registered to each button, such as input source,
volume level and sound mode settings.
 Remote control signal transmitter
This transmits signals from the remote control unit.
 ECO Mode button
This switches to ECO Mode.
 POWER button (
)
This turns the power on/off.
 SLEEP button
This sets the sleep timer.
REMOTE CONTROL 1
HOME
REMOTE CONTROL 3
9
Remote Control (3 of 3)
 Channel select buttons (CHANNEL +, –)
These select preset broadcast stations.
 Page search buttons (PAGE )
These switch pages.
 OPTION button
This displays the option menu on the TV screen.
 VOLUME buttons ()
These adjusts the volume level.
 SETUP button
This displays the menu on the TV screen.
 MUTE button ()
This mutes the output audio.
REMOTE CONTROL 2
HOME
WARRANTY 1
10
DENON LIMITED WARRANTY (1 of 2)
This warranty will be honored only in the U.S.A.
Length of Non-Transferable Warranty
This warranty on your DENON product which is distributed and warranted by DENON ELECTRONICS (USA), LLC remains in effect
for the following periods from the date of the original consumer purchase from an AUTHORIZED DENON ELECTRONICS (USA),
LLC DEALER.
2 years for units purchased new
1 year for refurbished (B-Stock) units
DENON ELECTRONICS (USA), LLC
(a D&M Holdings Company)
100 Corporate Drive
Mahwah, NJ 07430-2041
(201) 762-6665
www.usa.denon.com
DENON FACTORY SERVICE by PANURGY OEM
701 Ford Road (South Dock)
Rockaway, NJ 07866-2053
(973) 625-4056
(973) 625-9489 Fax
http://www.panurgyoem.com/Denon/Denonrepair.html
See the next page for more information about the Denon limited warranty
REMOTE CONTROL 3
HOME
WARRANTY 2
11
Warranty (2 of 2)
What is Covered
Except as specified below, this Warranty covers all defects in material and workmanship in this product occurring during the above warranty periods.
The following are not covered by the Warranty: (1) Any product which is not distributed in the U.S.A. by DENON ELECTRONICS (USA), LLC. (2) Any
product which is not purchased in the U.S.A. from an authorized DENON dealer. (Note: AUTHORIZED DENON DEALERS can be identified by
DENON AUTHORIZED DEALER sticker displayed in the stores. If you are uncertain as to whether a dealer is a DENON AUTHORIZED DEALER,
please contact DENON as listed below). (3) Any product on which the serial number has been defaced, modified or removed. (4) Damaged
deterioration or malfunction resulting from: a) Accident, act of nature, abuse, misuse, neglect, unauthorized product repair, opening of or modification
or failure to follow instructions supplied with the product. b) Repair or attempted repair by anyone not authorized by DENON. c) Any shipment of the
product (claim must be presented to carrier). (5) Items subject to wear from normal usage (tape heads, cartridges, stylus, battery, etc.). (6) Periodic
check-ups which do not disclose any defect. (7) Use of the product outside the U.S.A. (8) Damaged magnetic tape or CD/DVD/BD discs. (9) Use in
industrial, commercial, and/or professional applications. (10) Any installation or removal charges resulting from product failure.
What We Will Pay For
If during the applicable warranty period from the date of original consumer purchase your DENON product is found to be defective by DENON,
DENON will repair, or at its option, replace with new, reconditioned or equivalent model, such defective product without charge for parts or labor.
How to Obtain Warranty Performance
If your unit ever needs service, it may be taken or shipped to any authorized DENON service station or DENON ELECTRONICS (if you are uncertain
as to whether a service station is DENON authorized, please visit our website at http://usa.denon.com/us/Support/Pages/ServiceCenterSearch.aspx or
contact DENON as listed below.) In all other cases, the following procedures apply whenever your unit must be transported for warranty service;
You are responsible for transporting your unit or arranging for its transportation.
If shipment of your unit is required;
You must pay the initial shipping charges, but we will pay the return shipping charges if the repairs are covered by the Warranty.
WHEN RETURNING YOUR UNIT FOR WARRANTY SERVICE, A COPY OF THE ORIGINAL SALES SLIP MUST BE ATTACHED.
You should include the following: your name, address, daytime telephone number, model and serial number of the product and a description of
the problem. In the case of a CD/DVD/BD Player, please enclose ONE (1) disc that the unit has failed with for test reasons. It will be returned
with the unit.
THIS WARRANTY IS VALID IN THE U.S.A. ONLY.
If your product does not require service, but you have questions regarding its operation, please contact our Customer Support Department as listed
below.
THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION,
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
OUR LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT, AT OUR OPTION, OF ANY DEFECTIVE PRODUCT AND SHALL IN NO EVENT
INCLUDE INCIDENTAL OR CONSEQUENTIAL COMMERCIAL OR PROPERTY DAMAGES OF ANY KIND. WE ARE NOT RESPONSIBLE FOR
PRODUCTS LOST, STOLEN AND/OR DAMAGED DURING SHIPPING.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE
EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO
YOU.
This warranty gives you specific legal rights, but you may also have other rights which vary from state to state. This Warranty may not be altered other
than in a writing signed by an officer of Denon Electronics USA, LLC.
WARRANTY 1
HOME
RESET
12
Reset
Important: Back up the settings before resetting the microprocessor. Most settings are reset to the factory default values after performing
this procedure. This means that all the settings data will be completely lost if it’s not previously saved.
Reset procedure:
With the power off, press and hold the “TUNER
PRESET CH +” button, the “TUNER PRESET CH -”
button, and the “POWER” button simultaneously
on the AVR for a few seconds until “INITIALIZED”
appears on the AVR’s display
Power/Standby
button
Initialized
TUNER PRESET CH +” button
TUNER PRESET CH -” button
Resetting the micro is a procedure used to "reboot" the microprocessor to restore its normal operation when it temporarily freezes, locks
up, or behaves erratically. Resetting the microprocessor, erases any saved settings you may have previously programmed into the unit
Issues that can affect the performance of the microprocessor:
•
•
A jolt of static electricity
Current surge through an input
Before resetting the microprocessor;
•
•
•
Check all connections carefully
Check for setup errors
Back up your settings. You may also want to write down your preferred settings for easier task of setting up the AVR after reset.
Note: The Web (Browser) Control feature can be used to back up your settings by saving a configuration file on your hard drive. For this
feature, we recommend using one of the following web browsers: Internet Explorer 10 and above, Mozilla Firefox 24 and above, Google
Chrome 29 and above, and Safari 5.x and above.
Note: If you had an installer setup your system, please first contact your installer to see if they can reset and then setup your system again
as there may be specific EQ calibrations (Audyssey) that the installer will need to perform.
WARRANTY 2
HOME
ACCESSORIES
13
Accessories
Remote Control
(RC1189)
30701016700AD
$40.99
32401000800AD
$31.99
FM Indoor
Antenna
AM Loop
Antenna
963116100070S
Sound
Calibration
Microphone
Stand
Sound
Calibration
Microphone
(ACM1HB)
$8.99
943116100170D
$5.44
943611500590S
$9.99
Safety
Instructions
Warranty
(For North
America Only)
Quick Start
Guide
RESET
$16.82
Power Cord)
CD ROM
Owner’s
Manual
Notes on Radio
963549101000D
HOME
FAQ’s
14
FAQ’s ( 1 of ?)
ACCESSORIES
HOME
FAQ’s 2
15
FAQ’s (2 of ?)
FAQ’s 1
HOME
UPGRADE
16
Upgrades/Updates
Firmware:
This unit has the ability to update its firmware over the internet if so is selected by the user. When connected to a network via Wi-Fi or Ethernet, the AVR
searches automatically for new updates and if any is found, a message appears on the screen for approx. 40 seconds with the options of updating the
firmware: “NOW”, “LATER”, or “IGNORE”. Note: This feature of displaying the update message, can be disable from the “Setup” menu
(Setup/General/Firmware/Notifications/Update or Upgrade/Off).
If the update process is interrupted, “Update retry” appears on the display and the unit tries repeatedly to continue the update until it either reconnects and
picks up where it left off and continue the update process or times itself out after trying several times. When the latter occurs, one of the following messages
will appear on the screen.
Connection fail
Download fail
Updating fail
Server is busy
Login failed
To Check for Firmware Update from the Denon server when the unit is connected to the internet via the Ethernet port (When Firmware Notification is
turned off).
Press “SETUP” and select “GENERAL” and then select “FIRMWARE” followed by “UPDATE” and finally, select “CHECK FOR UPDATE”.
Note: This will also check the time it will approximately take to complete the update.
To download the latest version of firmware for AVR-S700W, click on the following Upgrade page:
www.usa.denon.com/US/Downloads/Pages/Product-Updates.aspx
To display the AVR’s current firmware version on the TV screen:
Press “SETUP” and select “GENERAL” and then select “INFORMATION” followed by “FIRMWARE”.
To check to see if an update or upgrade is available for your unit and also to see a list of “Recent Updates/Upgrades”, click on the following link:
http://usa.denon.com/us/downloads/productupdates?_ga=1.114028992.611911196.1430951505
FQA’s 2
HOME
Specifications – Audio Section
17
Specifications – Audio Section
Audio section
75 W + 75 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.)
Front
110 W + 110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
75 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.)
Center
Power amplifier
110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Rated output
75 W + 75 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.)
Surround
110 W + 110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
75 W + 75 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.)
Surround back
110 W + 110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Output connector
Input sensitivity/Input impedance
4 – 16 Ω/ohms
200 mV/47 kΩ/kohms
Frequency response
10 Hz – 100 kHz — +1, –3 dB (Direct mode)
S/N
98 dB (IHF–A weighted, Direct mode)
Analog
Upgrades/Updates
SPECIFICATIONS - VIDEO –
TUNER – WIRELESS LAN
HOME
SPECIFICATIONS
BLUETOOTH - GENERAL
SPECIFICATIONS DIMENSIONS - WEIGHT
18
Specifications - Video section,Tuner Section,Wireless LAN Section
Video section
Standard video connectors
Input/output level and impedance
1 Vp-p, 75 Ω/ohms
Frequency response
5 Hz - 10 MHz – 0, -3dB
Tuner section
FM
AM
1x10-15 W
Note: µV at 75 Ω/ohms, 0 dBf =
87.5 MHz - 107.9 MHz
1.2 µV (12.8 dBf)
MONO ― 2.8 μV (20.2 dBf)
MONO
70 dB (IHF–A weighted, Direct mode)
Reception frequency range
Effective sensitivity
50 dB sensitivity
S/N ratio
Distortion
STEREO
67 dB (IHF–A weighted, Direct mode)
Mono
0.7 %
Stereo
1.0 %
520 KHz -1710 KHz
18µV
Wireless LAN section
Network type (wireless LAN standard)
Conforming to Wi-Fi® *1
Security
WEP 64 bit, WEP 128 bit
WPA/WPA2-PSK (AES)
WPA/WPA2-PSK (TKIP)
Radio frequency
Number of channels
2.4 GHz
1 - 11ch
*1 The Wi-fi® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product Logo are registered trademarks of the Wi-Fi Alliance.
SPECIFICATIONS AUDIO
SPECIFICATIONS - VIDEO –
TUNER – WIRELESS LAN
HOME
SPECIFICATIONS
BLUETOOTH - GENERAL
SPECIFICATIONS DIMENSIONS - WEIGHT
19
Specifications – Bluetooth Section, General Section
Bluetooth section
Communications system
Bluetooth Version 2.1 + EDR (Enhanced Data Rate)
Transmission power
Maximum communication range
Frequency band
Modulation scheme
Maximum 2.5 mW (Class 2)
Approx. 32.8 ft/10 m in line of sight *2
2.4 GHz band
FHSS (Frequency-Hopping Spread Spectrum)
A2DP (Advanced Audio Distribution Profile) 1.2
Supported files
AVRCP (Audio Video Remote Control Profile) 1.4
Corresponding codec
SBC, AAC
Transmission range (A2DP)
20 Hz ~ 20,000 Hz
*2 The actual communication range varies depending on the influence of such factors as obstructions between devices, electromagnetic
waves from microwave ovens, static electricity, cordless phones, reception sensitivity, antenna performance, operating system,
application software, etc.
Power supply
Power consumption
Power consumption in standby mode
Power consumption in CEC standby mode
Power consumption in network standby mode
General section
AC 120V, 60Hz
400 W
0.1W
0.5W
2.7W
For purpose of improvement, specifications and design are subject to change without notice.
SPECIFICATIONS AUDIO
SPECIFICATIONS - VIDEO –
TUNER – WIRELESS LAN
HOME
SPECIFICATIONS
BLUETOOTH - GENERAL
SPECIFICATIONS DIMENSIONS - WEIGHT
20
Specifications – Dimensions, Weight
Dimensions section (Unit : inch/mm)
Weight: 18 lbs 15 oz (8.6 kg)
SPECIFICATIONS AUDIO
SPECIFICATIONS - VIDEO –
TUNER – WIRELESS LAN
HOME
SPECIFICATIONS
BLUETOOTH - GENERAL
SPECIFICATIONS DIMENSIONS - WEIGHT
21
The End
NOTE:
This edition is missing the FAQ’s content (pages 15 and 16) ………………………………………………………..7/1/2015
This edition is missing the link to the IR Codes………………………………………………………………………....7/1/2015
HOME
22