Sharp PN-L702B touch screen monitor

PN-L702B
LCD MONITOR
OPERATION MANUAL
IMPORTANT:
To aid reporting in case of loss or theft, please record the
product’s model and serial numbers in the space provided.
The numbers are located in the rear of the product.
Model No.:
Serial No.:
U.S.A. ONLY
FOR CUSTOMERS IN U.K.
IMPORTANT
The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW:
Earth
BLUE:
Neutral
BROWN:
Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
•The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth or coloured green or green-and-yellow.
•The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black.
•The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.
Ensure that your equipment is connected correctly. If you are in any doubt consult a qualified electrician.
“WARNING: THIS APPARATUS MUST BE EARTHED.”
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.
NOTE:
This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
This product utilizes a CR coin Lithium battery which contains a Perchlorate material.
Special handling for this material may apply,
California residents, See www.dtsc.ca.gov/hazardouswaste/perchlorate/
Others, consult local environmental officers.
U.S.A. ONLY
3
E
IMPORTANT INFORMATION (Continued)
Attention: Your product is marked with this symbol. It means that used electrical and electronic products
should not be mixed with general household waste. There is a separate collection system for these products.
EU ONLY
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dustbin!
Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper
treatment, recovery and recycling of used electrical and electronic equipment.
Following the implementation by member states, private households within the EU states may return their used electrical and
electronic equipment to designated collection facilities free of charge*. In some countries* your local retailer may also take
back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately beforehand
according to local requirements.
By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery and
recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due
to inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t
purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch.
B. Information on Disposal for Business Users
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the
costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection
facilities.
For Spain: Please contact the established collection system or your local authority for take-back of your used products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.
EU ONLY
The battery supplied with this product contains traces of Lead.
For EU:
The crossed-out wheeled bin implies that used batteries should not be put to the general household
waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in
accordance with legislation. Please contact your local authority for details on the collection and recycling
schemes.
For Switzerland:
The used battery is to be returned to the selling point.
For other non-EU countries:
Please contact your local authority for correct method of disposal of the used battery.
“BATTERY DISPOSAL”
THIS PRODUCT CONTAINS A LITHIUM PRIMARY (MANGANESS DIOXIDE) MEMORY BACK-UP BATTERY THAT
MUST BE DISPOSED OF PROPERLY. PLEASE CONTACT YOUR LOCAL SHARP DEALER OR AUTHORIZED SERVICE
REPRESENTATIVE FOR ASSISTANCE IN DISPOSING OF THIS BATTERY.
U.S.A. AND CANADA ONLY
E
4
DEAR SHARP CUSTOMER
Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your
product, please read the Safety Precautions carefully before using this product.
SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can
result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing,
operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the
following precautions carefully before using the product.
1. Read instructions — All operating instructions must be read and understood before the product is operated.
2. K
eep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future
reference.
3. Observe warnings — All warnings on the product and in the instructions must be observed closely.
4. Follow instructions — All operating instructions must be followed.
5. Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do
not use liquid cleaners or aerosol cleaners.
6. Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result
in accidents.
7. Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto
it. Be careful of equipment which drains water such as an air-conditioner.
8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.
Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life
of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings.
Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from
resting on them.
10. The screen used in this product is made of glass. Therefore, it can break when the product is dropped or applied with
impact. Be careful not to be injured by broken glass pieces in case the screen breaks.
11. Overloading — Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.
12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage flows in
the product, and inserting an object can cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.
13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other
dangerous conditions. Request a qualified service person to perform servicing.
14. Repair — If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service
person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls
not described in the instructions can cause damage, which often requires extensive adjustment work by a qualified
technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product
needs servicing.
15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement
parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of
unauthorized parts can result in fire, electric shock and/or other danger.
16. Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to
ensure that the product is in proper operating condition.
17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method
recommended by the manufacturer.
18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
5
E
SAFETY PRECAUTIONS (Continued)
19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment,
dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:
• Use the specified batteries only.
• Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the
compartment.
• Do not mix old and new batteries.
• Do not mix batteries of different types. Voltage specifications of batteries of the same shape may vary.
• Replace an exhausted battery with a new one promptly.
• If you will not use the remote control for a long time, remove the batteries.
• If leaked battery fluid gets on your skin or clothing, rinse immediately and thoroughly. If it gets into your eye, bathe your
eye well rather than rubbing and seek medical treatment immediately. Leaked battery fluid that gets into your eye or your
clothing may cause a skin irritation or damage your eye.
20. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,
severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and
missile launch control in a weapon system.
21. Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in
low-temperature burns.
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate counter measures.
To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: PC/AV DVI-D output
terminal, PC/AV DVI-D input terminal, PC/AV HDMI input terminal, PC D-SUB input terminal, PC RGB input terminals, and
RS-232C input/output terminals.
If a monitor is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries,
particularly to children, can be avoided by taking simple precautions such as:
• Using fixing devices like wall mount brackets recommended by the manufacturer.
• Only using furniture that can safely support the monitor.
• Ensuring the monitor is not overhanging the edge of the supporting furniture.
• Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the
monitor to a suitable support.
• Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the monitor or its controls.
Especially for child safety
- Don’t allow children to climb on or play with the monitor.
- Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.
- Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care
should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.
- Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by
curious children.
E
6
TIPS AND SAFETY INSTRUCTIONS
- The TFT color LCD panel used in this monitor is made with
the application of high precision technology. However, there
may be minute points on the screen where pixels never light
or are permanently lit. Also, if the screen is viewed from
an acute angle there may be uneven colors or brightness.
Please note that these are not malfunctions but common
phenomena of LCDs and will not affect the performance of
the monitor.
- Do not display a still picture for a long period, as this could
cause a residual image.
- Never rub or tap the monitor with hard objects.
- Please understand that SHARP CORPORATION bears no
responsibility for errors made during use by the customer or
a third party, nor for any other malfunctions or damage to this
product arising during use, except where indemnity liability is
recognized under law.
- This monitor and its accessories may be upgraded without
advance notice.
- Do not use the monitor where there is a lot of dust, where
humidity is high, or where the monitor may come into contact
with oil or steam, as this could lead to fire.
- Ensure that the monitor does not come into contact with
water or other fluids. Ensure that no objects such as paper
clips or pins enter the monitor as this could lead to fire or
electric shock.
- Do not place the monitor on top of unstable objects or in
unsafe places. Do not allow the monitor to receive strong
shocks or to strongly vibrate. Causing the monitor to fall or
topple over may damage it.
- Do not use the monitor near heating equipment or in places
where there is likelihood of high temperature, as this may
lead to generation of excessive heat and outbreak of fire.
- Do not use the monitor in places where it may be exposed to
direct sunlight.
- The AC outlet shall be installed near the equipment and shall
be easily accessible.
- Do not touch the screen while the PC is starting up, since
it will be detected as a failure of the infrared transmitter/
receiver elements and will lead to a malfunction. When this
occurs, restart the PC.
- Do not operate the screen with a hard or pointed object such
as a fingernail, pen, or pencil.
- Two touch panels cannot be used when two displays are
connected to the computer.
Only the touch panel on the display that is set as the primary
monitor will be operable.
- If another USB device is connected to the computer to which
the touch panel is connected, do not operate the USB device
during touch panel input. Input may not take place correctly.
The Power Cord
- Use only the power cord supplied with the monitor.
- Do not damage the power cord nor place heavy objects on
it, stretch it or over bend it. Also, do not add extension cords.
Damage to the cord may result in fire or electric shock.
- Do not use the power cord with a power tap.
Adding an extension cord may lead to fire as a result of
overheating.
- Do not remove or insert the power plug with wet hands.
Doing so could result in electric shock.
- Unplug the power cord if it is not used for a long time.
- Do not attempt to repair the power cord if it is broken
or malfunctioning. Refer the servicing to the service
representative.
Manual Scope
- Microsoft, Windows, Windows Vista and Internet Explorer
are registered trademarks of Microsoft Corporation.
- HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
- Adobe, Acrobat, and Reader are either registered trademarks
or trademarks of Adobe Systems Incorporated in the United
States and/or other countries.
- Intel, Celeron, and Intel Core 2 Duo are trademarks or
registered trademarks of Intel Corporation or its subsidiaries
in the U.S.A. and other countries.
- AMD, AMD Sempron, AMD Athlon, and combinations thereof
are trademarks of Advanced Micro Devices, Inc.
- This product comes with RICOH Bitmap Fonts produced and
sold by RICOH COMPANY, LTD.
- All other brand and product names are trademarks or
registered trademarks of their respective holders.
- Language of OSD menu used in this manual is English by
way of example.
- Illustrations in this manual may not exactly represent the
actual product or display.
LED Backlight
● The LED backlight in this product has a limited lifetime.
* If the screen gets dark or does not turn on, it may be
necessary to replace the LED backlight. This LED
backlight is exclusive to this product and must be replaced
by an authorized Sharp servicing dealer or service center.
* Please contact your local Sharp servicing dealer or
service center for assistance.
- If two touch panels are used in close proximity to each other,
use handwriting mode. The touch pens will interfere with
each other and will not operate correctly.
- If the infrared transmitter/receiver becomes dirty,
malfunctioning may result. Use a soft cloth to gently wipe dirt
off the infrared transmitter/receiver.
- If dust accumulates inside the infrared transmitter/receiver,
the product cannot transmit or receive infrared rays properly,
resulting in a malfunction. To clean the dust accumulated
inside, contact an authorized SHARP servicing dealer or
service center (extra charge required).
7
E
MOUNTING PRECAUTIONS
• This product is for use indoors.
• A mounting bracket compliant with VESA specifications is
required.
• Since the monitor is heavy, consult your dealer before
installing, removing or moving the monitor.
• Mounting the monitor on the wall requires special expertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this
work yourself. Our company will bear no responsibility
for accidents or injuries caused by improper mounting or
mishandling.
• This monitor cannot be used in vertical orientation.
• Use the monitor with the surface perpendicular to a level
surface. If necessary, the monitor may be tilted up to 20
degrees upward.
• When moving the monitor, be sure to hold it with either both
handles or the 4 corners on the bottom of the unit. Do not
place your hand on the screen. This may cause product
damage, failure, or injury.
• This monitor should be used at an ambient temperature
between 41°F (5°C) and 95°F (35°C). Provide enough
space around the monitor to prevent heat from
accumulating inside.
Unit: inch [cm]
7-7/8 [20]
2
[5]
1-7/16 [3.5]
2
[5]
2 [5]
• If it is difficult to provide sufficient space for any reason
such as the installation of the monitor inside a housing, or
if the ambient temperature may be outside of the range
of 41°F (5°C) to 95°F (35°C), install a fan or take other
measures to keep the ambient temperature within the
required range.
• Temperature condition may change when using the monitor
together with the optional equipments recommended by
SHARP. In such cases, please check the temperature
condition specified by the optional equipments.
• Do not block any ventilation openings. If the temperature
inside the monitor rises, this could lead to a malfunction.
• Do not place the monitor on a device which generates heat.
• Do not use the product in locations where the unit is
exposed to direct sunlight or other strong light. Since this
product operates with infrared rays, such light may cause a
malfunction.
E
8
Contents
IMPORTANT INFORMATION.............................................3
DEAR SHARP CUSTOMER...............................................5
SAFETY PRECAUTIONS...................................................5
TIPS AND SAFETY INSTRUCTIONS................................7
MOUNTING PRECAUTIONS.............................................8
Supplied Components......................................................9
System Requirements......................................................9
Part Names......................................................................10
Connecting Peripheral Equipment................................12
Connection with a PC or AV equipment......................12
Connection when the PN-ZB01 (optional)
is attached...................................................................13
Connecting the Power Cord..........................................14
Binding Cables................................................................14
Removing the Handles...................................................14
Preparing the Remote Control Unit...............................15
Installing the batteries.................................................15
Remote control operation range..................................15
Turning Power On/Off.....................................................16
Turning on the main power.........................................16
Turning power on/off...................................................16
Disabling power on/off operations...............................17
Touch Pen Preparations/Touch Action.........................18
Inserting the battery....................................................18
Touch action and touch mode.....................................18
Touch action................................................................18
Other functions............................................................20
Cautionary points........................................................20
Eraser..........................................................................20
Basic Operation..............................................................21
Menu Items......................................................................23
Displaying the menu screen........................................23
Menu item details........................................................24
Adjustments for PC screen display.............................30
Initialization (Reset)/Functional Restriction Setting
(FUNCTION).....................................................................31
Controlling the Monitor with a PC (RS-232C)...............32
PC connection.............................................................32
Communication conditions..........................................32
Communication procedure..........................................32
Setting of the GAMMA user data.................................35
RS-232C command table............................................36
Controlling the Monitor with a PC (LAN)......................43
Settings to connect to a LAN.......................................43
Controlling with a PC...................................................45
Troubleshooting..............................................................51
Specifications ................................................................53
Mounting Precautions
(For SHARP dealers and service engineers)................57
For information on the touch panel driver, see the Touch Panel Driver Operation Manual. For information on the Pen Software,
see the Pen Software Operation Manual.
Supplied Components
If any component should be missing, please contact your dealer.
 Liquid Crystal Display Monitor: 1
 Remote control unit: 1
 Cable clamp: 2
 Power cord: 1
 R-6 battery (“AA” size): 2
 CD-ROM (Utility Disk for Windows): 1
 Setup Manual: 1
 Touch pen: 1
 Pen tip (for touch pen): 2
 Touch pen battery
(LR-03 (“AAA” size)): 1
 USB cable: 1
 Eraser: 1
 Tray: 1
 Tray mounting fitting
(cover / bracket): x 2
 Tray mounting screws: M5 x 4 / M4 x 2
erminal label: 1
T
Used when installing the interface
expansion board PN-ZB01 (optional).
over Sharp logo: 1
C
Place this sticker onto the SHARP logo to
cover the logo.
* Sharp Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.
* For environmental protection!
Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
System Requirements
To use the touch panel, the touch panel must be connected to a computer, and the touch panel driver and Pen Software must be
installed on the computer from the supplied CD-ROM. System requirements for each software program are as follows.
Memory
PC/AT compatible computer with a USB 1.1 port (must be able to supply a 500 mA (5.0 V) current)
and able to output a resolution of 1920 x 1080. (CD-ROM drive required for software installation.)
Windows XP (32-bit or 64-bit version), Windows Vista (32-bit or 64-bit version), Windows 7 (32-bit
or 64-bit version)
Intel Celeron or AMD Sempron 1.6 GHz or faster
Intel Core 2 Duo or AMD Athlon II X2 2.8 GHz or faster recommended
At least 2 GB (at least 1 GB for Windows XP)
Free space on hard drive
At least 100 MB (free space separately required for data storage)
Computer
OS
CPU
To connect the touch panel and install the touch panel driver, see the Touch Panel Driver Operation Manual.
To install the Pen Software, see the Pen Software Operation Manual.
9
E
Part Names
nFront view
1
1
1.
2.
3.
4.
5.
6.
7.
8.
2
2
2
Touch pen ultrasonic sensor
Infrared transmitter/receiver
Power button (See page 16.)
Tray
Touch panel power LED
Remote control sensor (See page 15.)
Input switch (See page 21.)
Power LED (See page 16.)
2
3
4
5
6
7
8
nRear view
When the PN-ZB01
(optional) is attached
16
17
1
18
19
23
20
21
22
24
25
5
6
11
7
8
9
10
12
2
13
Caution
• Consult your SHARP dealer for attachment/detachment of
optional parts.
• Do not open the expansion terminal cover by yourself.
There are high voltage parts inside the cover which may
cause an electric shock.
E
10
14
15
1. Optional attachment section
This section is used to connect optional
hardware for function expansion.
Offering this attachment location is
not a guarantee that future compatible
hardware attachments will be released.
2. Speakers
3. Handles (See page 14.)
4. Vents
5. Expansion terminal cover
3
Additional input/output terminals are
available by attaching the PN-ZB01
4
interface expansion board (optional).
6. PC/AV HDMI input terminal (See page
12.)
7. PC D-sub input terminal (See page
12.)
8. Audio input terminal (See page 12.)
9. Audio output terminals (See page 12.)
10. RS-232C output terminal (See page
12.)
11. RS-232C input terminal (See page 12.)
12. Optional terminal
This terminal is provided for possible
future (optional) function expansion.
Offering of this terminal is not a
guarantee that future expanded
functionality will be provided.
13. USB port
14. AC input terminal (See page 14.)
15. Main power switch (See page 16.)
When the PN-ZB01 (optional) is attached
16. PC/AV DVI-D input terminal (See page 13.)
17. PC/AV DVI-D output terminal (See page 13.)
18. LAN terminal (See page 13.)
19. External speaker terminals (See page 13.)
20. Audio 1 input terminals (See page 13.)
21. Audio 2 input terminals (See page 13.)
22. PC RGB input terminals (See page 13.)
23. AV component input terminals (See page 13.)
24. AV video input terminal (See page 13.)
25. AV S-video input terminal (See page 13.)
Part Names
nRemote control unit
1
2
7
3
8
4
5
1.
2.
3.
4.
5.
6.
7.
8.
9.
Signal transmitter
POWER button (See page 16.)
MUTE button (See page 21.)
VOL +/- buttons (See page 21.)
BRIGHT +/- buttons (See page 21.)
Cursor control ( /
/
/ ) buttons
DISPLAY button (See page 21.)
MODE button (See page 21.)
INPUT button (See page 21.)
MENU button (See page 21.)
SIZE button (See page 21.)
9
6
11
E
Connecting Peripheral Equipment
When the PN-ZB01 (optional) is attached
7
15
13
14
12
9
1
8
10
11
5
2
3
4
5
6
Caution
• Be sure to turn off the main power switch and disconnect
the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the
equipment to be connected.
• Be careful not to confuse the input terminal with the output
terminal when connecting cables. Accidentally reversing
cables connected to the input and output terminals may
cause malfunctions and the other problems.
TIPS
• When using the touch panel, connect the USB cable to
the computer. For details, see the Touch Panel Driver
Operation Manual.
• Images may not be displayed properly depending on the
computer (video card) to be connected.
• A screen with 1920 x 1080 resolution may not be displayed
correctly on PC RGB. In this case, check the settings of
your computer (video card) to verify that input signals
conform to specifications of this monitor. (See page 55.)
• If there is a check box to disable EDID in display control
panel, check it when using PC RGB.
• Use the automatic screen adjustment when a PC screen
is displayed for the first time using PC D-SUB or PC RGB,
or when the setting of the PC is changed. The screen is
adjusted automatically when SELF ADJUST in the OPTION
menu is set to ON.
• If the audio output from the playback device is connected
directly to speakers or other devices, the video on the
monitor may appear delayed from the audio portion.
Audio should be played through this monitor by connecting
the playback device to the monitor’s audio input, and
connecting the monitor’s audio output to the speakers or
other devices.
• The audio input terminals used in each input mode are
factory-set as follows.
Input mode
PC D-SUB, PC DVI-D, PC RGB
AV DVI-D
AV component (BNC),
AV S-video , AV video (BNC)
AV COMPONENT (D-SUB),
AV video (D-SUB)
PC HDMI, AV HDMI
E
12
Audio input terminal
(Factory setting)
Audio input terminal
Audio1 input terminal
Audio2 input terminal
Audio input terminal
PC/AV HDMI input terminal
Connection with a PC or AV equipment
1. PC/AV HDMI input terminal
• Use a commercially available HDMI cable (conforming to
the HDMI standard).
• Set HDMI of INPUT SELECT on the OPTION menu
according to the device to be connected.
• Select the audio input terminal to be used in PC HDMI
or AV HDMI of AUDIO SELECT on the OPTION menu.
When HDMI is selected, connection to the audio input
terminal is unnecessary.
2. PC D-sub input terminal
• Set D-SUB of INPUT SELECT on the OPTION menu
according to the device to be connected.
• Common terminal for AV COMPONENT and AV VIDEO.
• When the PN-ZB01 (optional) is attached, select the audio
input terminal to be used in PC D-SUB of AUDIO SELECT
on the OPTION menu.
• To use with AV VIDEO (D-SUB), connect the green
terminal to the device’s video output.
3. Audio input terminal
• Use an audio cable without resistance.
• When the PN-ZB01 (optional) is attached, set the audio
input terminal used for each input mode in AUDIO
SELECT on the OPTION menu.
4. Audio output terminals
• The output sound varies depending on the input mode.
• The volume of the output sound can be fixed by setting
AUDIO OUTPUT (RCA) on the OPTION menu.
• It is not possible to control the sound output from the
audio output terminals with the AUDIO menu.
5.RS-232C input terminal
RS-232C output terminal
• You can control the monitor from a PC by connecting a
commercially available RS-232 straight cable between
these terminals and the PC.
6. USB port
• To use the touch panel, connect the touch panel to your
computer with the provided USB cable. (Touch Panel
Driver Operation Manual.)
Connecting Peripheral Equipment
Connection when the PN-ZB01
(optional) is attached
The PN-ZB01 expansion board (optional) allows the use of
additional connection terminals.
7. PC/AV DVI-D input terminal
• Set DVI of INPUT SELECT on the OPTION menu
according to the device to be connected.
• Select the audio input terminal to be used in PC DVI-D or
AV DVI-D of AUDIO SELECT on the OPTION menu.
8. PC RGB input terminals
• Set BNC of INPUT SELECT on the OPTION menu to PC
RGB when using the PC RGB input terminals.
• Select the audio input terminal to be used in PC RGB of
AUDIO SELECT on the OPTION menu.
9. AV component input terminals
• Set BNC of INPUT SELECT on the OPTION menu to
AV COMPONENT when using the AV component input
terminals.
• Select the audio input terminal to be used in AV
COMPONENT of AUDIO SELECT on the OPTION menu.
• Cannot be used when D-SUB in INPUT SELECT on the
OPTION menu is set to AV COMPONENT.
10. AV video input terminal
• Select the audio input terminal to be used in AV VIDEO of
AUDIO SELECT on the OPTION menu.
• Cannot be used when D-SUB in INPUT SELECT on the
OPTION menu is set to AV VIDEO.
11. AV S-video input terminal
• Select the audio input terminal to be used in AV S-VIDEO
of AUDIO SELECT on the OPTION menu.
12. Audio1 input terminals / Audio2 input terminals
• Set the audio input terminal to be used in each input
mode in AUDIO SELECT on the OPTION menu.
13. LAN terminal
• You can control the monitor from a PC on a network by
connecting a commercially available LAN cable between
this terminal and a network.
14. External speaker terminals
• To use external speakers, set SPEAKER SELECT on the
SETUP menu to EXTERNAL.
• Be sure to use external speakers with an impedance of 6 Ω
or greater and a rated input of at least 7 W.
1
Approx.
3-15/16 inch
(10 cm)
2
3
1. Attach a speaker cable core (included with the PN-ZB01) to
the end of the speaker cable connected to the monitor.
2. While pushing the tab, insert the tip of the cable.
3. Release the tab.
TIPS
• Be sure to connect the + and - terminals and the left and
right speakers properly.
• Avoid short circuiting the + and - terminals.
• When SPEAKER SELECT is set to EXTERNAL, the
internal speakers are disabled.
15.
PC/AV DVI-D output terminal
• The video of the PC/AV DVI-D input can be output to an
external device.
• Outputting HDCP-encrypted video requires an external
device which supports HDCP.
• This terminal allows the daisy chain connection of up to 5
monitors.
TIPS
• The length of the signal cables or surrounding environment
may affect the image quality.
• The screen may not display properly when using terminals
other than PC DVI-D/AV DVI-D for the input mode. In this
case, turn off the power to all the monitors connected in a
daisy chain and then turn the power on again.
• When connecting monitors in a daisy chain set AUTO
INPUT CHANGE to OFF.
• Video output is disabled in the following cases:
When the power is turned off
When the monitor is in input signal waiting mode
13
E
Connecting the Power Cord
Caution
• Do not use a power cord other than the one supplied with
the monitor.
1. Turn off the main power switch.
2. Plug the power cord (supplied) into the AC input terminal.
3. Plug the power cord (supplied) into the AC power outlet.
3 For power
Main power switch
outlet
2
Power cord (Supplied)
1
AC input terminal
Binding Cables
The cables connected to the terminals on the rear of the
monitor can be fastened with the cable clamp.
Insert the cable clamp into the cable clamp attachment on the
rear of the monitor and fasten the cables.
Cable
Cable clamp
attachment
Cable clamp
Removing the Handles
The handles can be removed.
The installation position can be changed.
Handle
Handle screws
Caution
• The removable handles and handle screws are for use with this monitor. Do not use them for any other devices.
• To attach handles, be sure to use the handles and handle screws which were removed from the monitor.
• Be sure the handles are attached securely.
E
14
Preparing the Remote Control Unit
Installing the batteries
Remote control operation range
1. Press the cover gently and slide it in the direction of the
arrow.
The operation range of the remote control unit is approx. 16.4
feet (5 m) at an angle of approx 10° from the center to the top/
bottom/right/left of the remote control sensor.
2. See the instructions in the compartment and put in the
supplied batteries (R-6 (“AA” size) x 2) with their plus (+)
and minus (-) sides oriented correctly.
3. Close the cover.
Remote
control sensor
TIPS
10°
• When the batteries become exhausted, replace them with
new (commercially available) batteries.
• The supplied batteries (R-6 (“AA” size) x 2) may become
exhausted quickly depending on how they are stored.
• If you will not be using the remote control for a long time,
remove the batteries.
• Use manganese or alkaline batteries only.
10°
10°
16.4
feet
(5 m)
10°
TIPS
• Do not expose the remote control unit to shock by dropping
or stepping on it. This could lead to a malfunction.
• Do not expose the remote control unit to liquids, and do not
place it in an area with high humidity.
• The remote control unit may not work properly if the remote
control sensor is under direct sunlight or strong lighting.
• Objects between the remote control unit and the remote
control sensor may prevent proper operation.
• Replace the batteries when they run low as this may
shorten the remote control’s operation range.
• If a fluorescent light is illuminated near the remote control
unit, it may interfere with proper operation.
• Do not use it with the remote control of other equipment
such as air conditioner, stereo components, etc.
15
E
Turning Power On/Off
Caution
• Turn on the monitor first before turning on the PC or
playback device.
Turning power on/off
Press the POWER button to turn the power ON/OFF.
Turning on the main power
Touch panel power LED
Main power switch
Power LED
• Status of the power LED
Status
Caution
• The main power must be turned on/off with the main power
switch. Do not connect/disconnect the power cord or turn
the breaker on/off while the main power switch is on.
• When switching the main power switch or the POWER
button off and back on, always wait for at least 5 seconds.
• For a complete electrical disconnection, pull out the main
plug.
POWER
button
Status of the monitor
Green lit
Power on
Orange lit
Power off (Standby mode)
Green flashing
Input signal waiting mode
• Status of the touch panel power LED
Status
Status of the touch panel
Green lit
Operating normally
Blinking orange
Alternately blinking green and Initializing
orange
Touch panel off (power not
Off
supplied, etc.)
Caution
• When switching the main power switch or the POWER
button off and back on, always wait for at least 5 seconds.
A short interval may result in a malfunction.
• When the touch panel power LED blinks orange or
alternately blinks green and orange, the touch panel is
being initialized. Do not touch the touch panel at this time.
Touching the touch panel may cause malfunctioning.
TIPS
• When the main power switch is off, the monitor cannot be
turned on.
• If the monitor is in the input signal standby mode and you
press the POWER button on the remote control unit, the
monitor enters standby mode.
• Setting the SCHEDULE flashes the power LED alternately
in red and orange in standby mode.
• To disable the logo screen from displaying when turning
the power ON, set LOGO SCREEN to OFF on the SETUP
menu. (See page 26.)
E
16
Turning Power On/Off
nDate/time setting
• If the time has yet to be set when the monitor is first turned
on, the date/time setting screen appears. Set the date and
time.
DATE/TIME SETTING
/
SET
/
01 / 01 / 20 11
:
Disabling power on/off operations
Power on/power off operations can be disabled in order to
protect the monitor from an accidental power off. Set the
ADJUSTMENT LOCK in FUNCTION menu to “ON 2”. (See
page 31.)
:
12 : 00
AM
CANCEL
OK···[MENU]
1. Press
,
,
or
to select the date and
or
to change the numerical
time, and press
values.
2. Select SET and then press MENU .
• Be sure to set the date and time.
• The date/time setting screen will close automatically if no
operation is performed for about 15 seconds. The date
and time can be set using DATE/TIME SETTING from
the OPTION menu when the date/time setting screen
disappears.
TIPS
Set the date in “Month/Day/Year” order.
Set the time on a 12-hour basis.
The clock is maintained by the internal battery.
If you already set the time but the date/time setting
screen appears when the power is turned on, the
internal battery may be exhausted. Please contact
your local Sharp servicing dealer or service center for
assistance with battery replacement.
• Estimated service life of the internal battery: About 5
years (depending on monitor operation)
• The initial battery was inserted at the factory when the
monitor was shipped, so it may run out of power before
its expected operation life.
•
•
•
•
17
E
Touch Pen Preparations/Touch Action
Inserting the battery
Touch action and touch mode
1. Rotate the battery cap and remove it, and then pull out the
cover.
Touch panel actions that can be used vary depending on the
touch mode setting in the touch panel driver.
In Windows XP/Windows Vista, dual touch mode cannot be
used.
Battery cap
2. Insert the supplied battery (LR-03 (“AAA” size)) in the
orientation shown, and attach the cover and battery cap.
TIPS
• The supplied battery (LR-03 (“AAA” size)) may be
exhausted in a short time, depending on how it was stored.
• If the touch pen will not be used for an extended time,
remove the battery from the touch pen.
• For the battery, use an alkaline battery.
Touch mode
Touch action
Single touch mode
Dual touch mode
Single-tap
Yes
Yes
Double-tap
Yes
Yes
Drag-and-drop
Yes
Yes
Flicks
No
Yes
Press-and-hold
No
Yes
Pan
No
Yes
Zoom
No
Yes
Press-and-tap
No
Yes
TIPS
• Settings for touch panel operation such as the touch mode
and actions of the function buttons can be changed in the
touch panel driver. For details, see the manual for the touch
panel driver.
• In Windows 7, if the checkmark has been removed from
“Enable multi-touch gestures and inking” in “Pen and touch”
in Control Panel, select the checkbox.
Touch action
When the touch panel is touched with the pen, the input mode
changes to pen mode. When touched with your finger, the
input mode changes to handwriting mode. The input mode is
set by default to change automatically (Standard mode).
TIPS
• For the procedures for using the touch pen in the Pen
Software, see the Pen Software Operation Manual.
nCommon finger and pen actions
Single-tap
Same action as left-clicking a mouse.
Touch with your finger/pen.
E
18
Touch Pen Preparations/Touch Action
Double-tap*1
Same action as double-clicking a mouse.
Quickly touch twice with your finger/pen.
When double-tapping with your finger, be sure to lift your
finger sufficiently off the screen after the first tap. If there
is insufficient distance between the screen and your finger,
double-tap will not take place.
Drag-and-drop
Same action as drag-and-drop with a mouse.
Touch the screen with your finger/pen and move without lifting.
When you have finished the movement, lift your finger/pen.
Pan*2
Use in a screen with a scrollbar.
With your finger/pen touching the screen, move in the
direction you want to scroll. The screen scrolls in the direction
of the movement.
*1 In Windows XP/Windows Vista, the settings can be changed in
the touch panel driver.
*2 The settings can be changed in "Pen and touch" of Control Panel
in Windows 7. For details, see Windows Help.
nFinger actions
Zoom
Use in a screen that is capable of enlargement/reduction.
Touch the screen with two fingers and move your fingers
closer together to reduce the view, or apart to enlarge the
view.
Flicks*2
Flick your finger/pen in the direction of the function you want
to use.
Flick your finger
Press-and-hold*2
Same action as right-clicking a mouse.
Press briefly with your finger/pen, and then lift your finger/pen
from the screen.
Reduction
Enlargement
TIPS
• Move your finger diagonally across the screen. If you move
your finger horizontally or vertically, the screen may not
respond correctly.
19
E
Touch Pen Preparations/Touch Action
Press-and-tap
Same action as right-clicking a mouse.
With one finger touching the screen, tap once (single tap) with
another finger.
Tap once (single tap) with another finger
With one finger touching
Other functions
In Windows 7, touch pointer and input panel functions can be
used.
For information on these functions, see Windows Help.
Touch pointer :
A translucent image of a mouse appears near the point
touched. The left/right buttons of the image can be clicked
to perform the same actions as left/right clicking a mouse.
Input panel :
A software keyboard and an input panel with handwriting
recognition appear on the screen.
In Windows 7 (excluding Starter), the ink function of Microsoft
Office can be used.
Handwritten comments can be written, and handwriting can
be recognized.
For details, see Microsoft Office Help.
TIPS
• The screen may not respond correctly in the following
cases:
Touching is too quick
The distance between the two points is too short
The two points intersect
• Operation with the touch pen is not possible.
nPen actions
Function Button 2
Pen tip
Ultrasonic transmitter
Battery indicator
Function Button 1
Function Button 1
Pressing Function Button 1 has the same action as rightclicking a mouse.
The battery indicator illuminates.
Function Button 2
In the Pen Software, pressing Function Button 2 has the
action that is set in the Pen Software.
The battery indicator illuminates.
TIPS
• Use Function Button 1 and Function Button 2 near the front
of the screen. If too far away, operation will not be possible.
• Press Function Button 1 and Function Button 2 slowly
and firmly. If pressed too quickly, the action will not be
recognized.
• If the pen tip becomes worn or damaged, replace it. Pull
out the old pen tip and insert a new pen tip.
Cautionary points
• Do not use the touch pen for any purpose other than touch
panel operation.
• Do not press hard on the pen tip.
• Do not cover the ultrasonic transmitter of the touch pen with
your hand or finger.
• Operation will not take place correctly if there is an obstacle
between the infrared transmitter/receiver and the touch pen
or your finger. Operation will not take place correctly if your
fingers or your sleeve is near the screen.
• If the touch pen is held too flat against the screen, the
touch position may not be correctly detected.
• If the touch pen does not work at the edge of the screen,
move it slowly.
• Do not store with the pen tip of the touch pen or function
button pressed. The battery will be exhausted.
• Do not use near a device that emits ultrasonic waves. The
touch pen uses ultrasonic waves and may not operate
correctly.
• If two touch panels are used in close proximity to each
other, use handwriting mode. The touch pens will interfere
with each other and will not operate correctly.
• If there is dirt or foreign matter on the tip of the touch pen,
remove it. Foreign matter may damage the screen.
• Applications such as a screensaver or media player may
cause the resolution to automatically change. If "Resolution
Change Notice" is enabled in the touch panel driver, a
resolution change message will appear. In this case,
disable "Resolution Change Notice", or change the setting
in the application so that it does not change the resolution.
• The pen may be out of position in the login screen. In this
case, use the keyboard or mouse.
• If the USB cable becomes disconnected, the touch panel
may not operate correctly after the cable is reconnected. In
this case, restart your computer.
Eraser
The eraser is used with the Pen Software. For the procedure
for using the eraser, refer to the Pen Software Operation
Manual.
Caution
E
20
• When using the eraser, gently bring the cloth side into
contact with the screen. Touching the screen with one of
the non-cloth sides will damage the screen.
• If there is any dirt or foreign matter on the surface that
contacts the screen, remove it. Foreign matter may damage
the screen.
Basic Operation
2. MUTE
Turns off the volume temporarily.
Press the MUTE button again to turn the sound back to the
previous level.
1
2
3. MENU
Displays and turns off the menu screen. (see page 23.)
3
4
4. VOL +/- (Volume adjustment)
Pressing
or
displays the VOLUME menu when the
menu screen is not displayed.
5
VOLUME
Press
or
to adjust the volume of the sound.
* If you do not press any buttons for about 4 seconds, the
VOLUME menu automatically disappears.
6
7
8
5. BRIGHT +/- (Backlight adjustment)
Pressing
or
displays the BRIGHT menu when the
menu screen is not displayed.
1. INPUT (Input mode selection)
or
to select the input
The menu is displayed. Press
mode, and press
to enter.
* You can select the input terminal by pressing the input
switch of the monitor.
Input mode
PC D-SUB
Video
PC D-sub input
Audio
terminal*1
terminal*2
PC HDMI
PC/AV HDMI input
AV HDMI
PC/AV HDMI input terminal*2
AV COMPONENT PC D-sub input terminal*1
AV VIDEO
PC D-sub input terminal*1
Audio input terminal
*3
Audio input terminal
When the PN-ZB01 (optional) is attached
Input mode
15
Video
PC DVI-D
PC/AV DVI-D input terminal*4
PC HDMI
PC/AV HDMI input terminal*2
PC D-SUB
PC D-sub input terminal*1
PC RGB
PC RGB input terminals*5
AV DVI-D
PC/AV DVI-D input terminal*4
AV HDMI
PC/AV HDMI input terminal*2
Audio
*3
AV COMPONENT input
AV COMPONENT terminals*5
PC D-sub input terminal*1
AV S-VIDEO
AV S-video input terminal
AV VIDEO
AV video input terminal
PC D-sub input terminal*1
*1 Select the terminal to be used in D-SUB of INPUT
SELECT. (See page 26.)
*2 Select the terminal to be used in HDMI of INPUT SELECT.
(See page 26.)
*3 Select the terminal for AUDIO SELECT which is used for
audio input. (See page 26.)
*4 Select the terminal to be used in DVI of INPUT SELECT.
(See page 26.)
*5 Select the terminal to be used in BNC of INPUT SELECT.
(See page 26.)
BRIGHT
15
Press
or
to adjust the brightness.
* If you do not press any buttons for about 4 seconds, the
BRIGHT menu automatically disappears.
6. SIZE (Screen size selection)
The menu is displayed.
Press
or
to select the screen size. (See page 22.)
7. DISPLAY
Displays monitor information. When you press this button
again, the display disappears.
When the PN-ZB01 (optional) is attached, the display changes
from INFORMATION1 → INFORMATION2 → clear display,
and so on every time you press this button.
• The display disappears automatically after about 15
seconds.
• LAN is displayed during LAN communication.
• If LAN is displayed in red, there is a duplicate IP address.
8. MODE (Color mode selection)
Each time you press this button, the color mode changes in
the following order:
STD (Standard) → VIVID → sRGB → STD...
• sRGB applies to PC input only.
sRGB is international standard of color representation
specified by IEC (International Electrotechnical
Commission). Color conversion is made in taking account
of liquid crystal’s characteristics and represents color tone
close to its original image.
21
E
Basic Operation
nSwitching the screen size
Even when the screen size is changed, the display may remain the same depending on the input signal.
WIDE
ZOOM 1
PC input
Displays image so it fills the entire screen.
AV input
An image with a 4:3 aspect ratio is stretched to fill the entire
screen.
PC input
An image with a 4:3 aspect ratio is enlarged to fill the entire screen
without changing the aspect ratio. The edges of the image may be
cut off.
AV input
ZOOM 2
PC input
Use this size if ZOOM 1 cuts off the subtitles.
AV input
NORMAL
Dot by Dot
PC input
Displays image so it fills the screen without changing the aspect
ratio of the input signals.
AV input
Displays the entire image of the aspect ratio of 4:3 without
changing the aspect ratio.
PC input
Displays the dots of the signals input from the connected PC as
the corresponding dots on the screen.
AV input
Displays the dots of the input signals as the corresponding dots on
the screen.
TIPS
• Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial
or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright
Law, so please be careful.
• When dual-screen display is selected, the screen size cannot be changed.
• The appearance of the original video may change if you select a screen size with a different aspect ratio than the original
image (e.g. TV broadcast or video input from external equipment).
• When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this
monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen
size to “NORMAL”.
• When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen
size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the
edges of the screen. This is due to the characteristics of the software, and is not a malfunction.
• Depending on the original image size, black bands may remain at the edges of the screen.
E
22
Menu Items
Displaying the menu screen
TIPS
Caution
• Do not turn the main power switch off while the menu items
are being displayed. Doing so may initialize the settings.
nExample of operation
MENU
SCREEN
AUTO
AUDIO
CLOCK
PHASE
600
25
H-POS
V-POS
610
37
H-SIZE
V-SIZE
50
50
1920
1080
OPTION
PIP/PbyP
H-RESOLUTION
V-RESOLUTION
RESET
1920x1080
V: 60 Hz
PIP/PbyP
H: 67.5 kHz
END···[MENU]
or
to select PICTURE, and press
3. Press
or
to select CONTRAST.
SCREEN
PICTURE
AUDIO
SETUP
OPTION
PIP/PbyP
64
86
31
30
30
30
30
12
MOVE OSD···[DISPLAY]
1920x1080
V: 60 Hz
or
SCREEN
AUDIO
▲
SETUP
OPTION
PIP/PbyP
For items that have
MENU
press
.
5. Press
MENU
OK···[MENU]
PC D-SUB
64
86
31
40
30
30
30
12
, press
FULL
H: 67.5 kHz
▲
MOVE OSD···[DISPLAY]
1920x1080
V: 60 Hz
OK···[MENU]
4
1 Name of the menu
2 Input mode
3 An item being selected (highlighted)
4 Screen resolution of input signal, and other data.
TIPS
The displayed menu items vary depending on whether or not
the PN-ZB01 (optional) is attached.
The following menus will be displayed only when the PN-ZB01
(optional) is attached.
FULL
1/2
AUTO
ANALOG GAIN
ANALOG OFFSET
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
RGB INPUT RANGE
H: 67.5 kHz
nMenu Items
to adjust the setting.
PICTURE
PICTURE
FULL
• Items that cannot be selected appear in gray.
(e.g. Function not supported by the current input signal)
H: 67.5 kHz
▲
4. Press
64
86
31
30
30
30
30
12
PC D-SUB
1/2
AUTO
ANALOG GAIN
ANALOG OFFSET
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
RGB INPUT RANGE
.
PC D-SUB
1/2
MOVE OSD···[DISPLAY]
1920x1080
V: 60 Hz
2. Press
PICTURE
OPTION
AUTO
ANALOG GAIN
ANALOG OFFSET
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
RGB INPUT RANGE
2
▲
PICTURE
SETUP
SETUP
PC D-SUB
1/1
3
PICTURE
AUDIO
to display the menu screen.
SCREEN
1
▲
SCREEN
nMenu screen display
PICTURE
(Adjusting CONTRAST in the PICTURE menu)
1. Press
• The menu will differ depending on the input mode.
• The menu screen will close automatically if no operation is
performed for about 15 seconds. (DATE/TIME SETTING,
SCHEDULE and LAN SETUP screens will close in about 4
minutes.)
▲
Video and audio adjustment and settings of various functions
are enabled. This section describes how to use the menu
items. See pages 24 to 27 for details of each menu items.
OK···[MENU]
, make settings and then
Menu
SETUP
Item
HOT PLUG CONTROL DVI
RS-232C/LAN SELECT
LAN SETUP
SPEAKER SELECT
OPTION INPUT SELECT
DVI
BNC
AUDIO SELECT
PC DVI-D
PC D-SUB
PC RGB
AV DVI-D
AV COMPONENT (BNC)
AV COMPONENT (D-SUB)
AV S-VIDEO
AV VIDEO (BNC)
AV VIDEO (D-SUB)
PIP/PbyP PIP SOURCE
twice to close the menu screen.
23
E
Menu Items
Menu item details
The menu will differ depending on the input mode.
nSCREEN
You can move the menu screen display position each time
DISPLAY
is pressed.
AUTO (PC D-SUB/PC RGB)
The CLOCK, PHASE, H-POS, and V-POS are automatically
adjusted.
Pressing
performs adjustment.
Use this automatic adjustment when you use the PC D-sub
input terminal or PC RGB input terminals to display a PC
screen for the first time or when you change the setting of
the PC. (See page 30.)
CLOCK (PC D-SUB/PC RGB)
Adjusts frequency for sampling clock for applicable video.
Adjust when there is flickering in the form of vertical stripes.
When using the adjustment pattern (see page 30), make
adjustments so that no vertical stripe noise appears in it.
PHASE (PC D-SUB/PC RGB)
Adjusts sampling clock phase for applicable video.
Useful when small characters appear with low contrast and/
or there are flickers at corners.
When using the adjustment pattern (see page 30), make
adjustments so that no horizontal stripe noise appears in it.
* Adjustments to PHASE should be made only after CLOCK
has been correctly set.
H-POS
Adjust the horizontal position of the image.
V-POS
Adjust the vertical position of the image.
H-SIZE
Adjust the horizontal size of the image.
V-SIZE
Adjust the vertical size of the image.
H-RESOLUTION (PC D-SUB/PC RGB)
Sets proper horizontal resolution when the resolution of
input signals is not recognized properly. (Adjustment may be
impossible with some signals.)
V-RESOLUTION (PC D-SUB/PC RGB)
Sets proper vertical resolution when the resolution of input
signals is not recognized properly. (Adjustment may be
impossible with some signals.)
RESET
Resets the values of the SCREEN menu items to the factory
preset values.
MENU
Select “ON” and then press
.
E
24
nPICTURE
You can move the menu screen display position each time
DISPLAY
is pressed.
AUTO (PC D-SUB/PC RGB)
The ANALOG GAIN and ANALOG OFFSET are
automatically adjusted.
Pressing
performs adjustment.
ANALOG GAIN (PC D-SUB/PC RGB)
Adjusts the bright portions of the video input signal.
ANALOG OFFSET (PC D-SUB/PC RGB)
Adjusts the dark portions of the video input signal.
BRIGHT
Adjusts the backlight brightness. (In PIP mode, the main side
setting is reflected in the image.)
CONTRAST
Adjusts the difference between the bright and dark portions
of the image.
BLACK LEVEL
Adjusts the entire brightness of the video signals.
TINT
Adjusts the hue. Selecting + changes the color towards
green, and selecting - changes it towards magenta.
COLORS
Adjusts the color intensity.
SHARPNESS
Adjusts the sharpness of the image.
RGB INPUT RANGE (PC DVI-D/PC HDMI/PC D-SUB/PC
RGB/AV DVI-D/AV HDMI)
Sets the RGB input signal range. When using HDMI set to
AUTO, the RGB input signal is detected automatically. Use
AUTO normally.
If the RGB input signal range cannot be set appropriately
even when using AUTO, set according to the image. When
the setting is different, images will be displayed with washed
out blacks and compressed gradients.
ADVANCED (AV input)
You can adjust more specifically. (See page 30.)
COLOR MODE
Changes the color mode on the screen. The color mode on
the screen can also be changed using a remote control unit.
(See page 21.)
* sRGB is PC input only. See page 21 for details.
(In PIP mode, the main side setting is reflected in the image.)
WHITE BALANCE
THRU�������������� Displays the input signal level as is. (for PC
DVI-D/PC HDMI only)
PRESET��������� Selects the color temperature using PRESET.
USER�������������� Used for adjusting R-/G-/B-CONTRAST and
R-/G-/B-OFFSET respectively.
(In PIP mode, the main side setting is reflected in the image.)
PRESET
Selects the color temperature when the WHITE BALANCE is
set to PRESET.
The setting values are shown for reference. The color
temperature of the screen varies over time.
This function is not intended to keep the color temperature
constant.
Menu Items
USER
Adjusts each item when the WHITE BALANCE is set to
USER.
R-CONTRAST.....Adjusts bright-toned red component.
G-CONTRAST.....Adjusts bright-toned green component.
B-CONTRAST.....Adjusts bright-toned blue component.
R-OFFSET...........Adjusts dark-toned red component.
G-OFFSET..........Adjusts dark-toned green component.
B-OFFSET...........Adjusts dark-toned blue component.
COPY TO USER
Copies the value of white set for PRESET to the USER
setting.
MENU
Select “ON” and then press
.
(In the case other than white, color tone may differ from the
PRESET.)
GAMMA
Selects the gamma. USER sets the gamma to the sent
value (see page 35). (In PIP mode, the main side setting is
reflected in the image.)
DISPLAY COLOR PATTERN
Displays a color pattern. Can be displayed while the menu
screen is displayed, so you can refer to the pattern while
adjusting the image.
OFF............... No pattern display.
WHITE........... White single color pattern display.
RED............... Red single color pattern display.
GREEN.......... Green single color pattern display.
BLUE............. Blue single color pattern display.
USER����������� Red/green/blue mixed color pattern display.
When USER is selected, set each color’s
level.
RESET
Resets the values of the PICTURE menu items to the factory
preset values.
MENU
Select “ON” and then press
.
nAUDIO
TREBLE
Adjusts the volume of treble-level sound.
BASS
Adjusts the volume of bass-level sound.
BALANCE
Adjusts the balance of the audio sound between right and left.
RESET
Resets the values of the AUDIO menu items to the factory preset values.
MENU
Select “ON” and then press
.
nSETUP
OSD H-POSITION
Adjusts the horizontal display position of menu screen.
OSD V-POSITION
Adjusts the vertical display position of menu screen.
SCREEN MOTION
Residual images are reduced by moving the screen.
PATTERN1..........The whole screen moves vertically and
horizontally.
PATTERN2..........A black screen spreads from the bottom of
the screen and then shrinks to the bottom
of the screen.
PATTERN3..........A black bar moves from the left end to the
right end of the screen.
PATTERN4..........Black screens appear from both the
top and bottom of the screen, and the
displayed image is compressed into the
central field.
PATTERN1
PATTERN2
PATTERN3
PATTERN4
MOTION TIME 1
Specify a time period (operating interval) until SCREEN
MOTION starts.
MOTION TIME 2
Specify a time period during which SCREEN MOTION
operates (time period during which the screen will move).
MONAURAL AUDIO
Outputs audio signals as monaural.
LANGUAGE
Sets the display language for the menu screen.
POWER ON DELAY
You can delay the screen display after the monitor is turned
on. The period can be set up to 60 seconds in units of one
second. When this function is activated, the power LED
flashes (at approx. 1 second interval) in orange. This function
is disabled when 0 is specified.
STANDBY MODE
When STANDARD is selected, startup time from standby
mode is reduced. Note, however that, more power will be
consumed in standby mode.
When LOW POWER is selected, current consumption
is reduced while the monitor is in standby mode. Note,
however, that the startup time from standby mode becomes
longer.
If set to LOW POWER, certain RS-232C commands cannot
be used in standby mode, and control via LAN will be
disabled.
OFF IF NO OPERATION
Determines whether or not to set the monitor to go into
standby mode when there is no operation from the remote
control unit, RS-232C commands, or LAN for over 4 hours.
25
E
Menu Items
HOT PLUG CONTROL
Sets whether to use hot plug control for the PC/AV HDMI
and PC/AV DVI-D input terminals.
RS-232C/LAN SELECT
Selects the method with which to control the monitor from
the computer.
ID No. SET
Assigns ID numbers to monitors connected in a daisy chain
(see page 33), using RS-232 cables.
The numbers 1 to 255 are available for ID numbers.
If “0” is set, the system regards this as the state where no ID
number is set.
AUTO ASSIGN ID No.
ID No. to be used will be automatically assigned when
multiple monitors are connected with RS-232C.
MENU
.
Select ON, then press
Perform operations using the first monitor in the daisy chain.
BAUD RATE
Selects the communication speed used for RS-232C
communication.
LAN SETUP
Configures the settings to control the monitor from the
computer via LAN. (See page 43.)
AUTO ASSIGN FIXED IP ADDR.
Can be enabled when RS-232C/LAN SELECT is LAN and
the DHCP client is OFF.
Set DHCP CLIENT to OFF for the monitor connected to the
RS-232C output terminal and the daisy chain of connected
monitors that follows. Fixed IP addresses are automatically
allocated.
If the IP address is a duplicate with a network device other
than a monitor, individually change the IP address.
SPEAKER SELECT
Selects the speaker to be used.
HDMI AUTO VIEW
When ON is selected, the screen size is adjusted
automatically according to the screen size control signal
included in the video signal input from the AV HDMI input
terminal.
COPY SETTING VALUE
When the monitor has been connected to multiple monitors
by RS-232C, the settings in the monitor can be copied to the
monitor connected to the RS-232C output terminal and to
the daisy chain of connected monitors that follows.
Selects the settings to copy with COPY SETTING VALUE
TARGET.
“PICTURE” ONLY...... Copies the PICTURE menu settings.*
ALL............................ Copies all the settings.*
Select the ID No. of the monitor that you would like copy to
MENU
with COPY TO ID No., then select COPY and press
.
If you select ALL, settings will be copied to all monitors.
When you would like to confirm the ID No. that is set to the
. The ID No. will be
monitor, select ID No. and press
displayed on the screen.
* Certain setting details such as ANALOG GAIN, ANALOG
OFFSET, and DISPLAY COLOR PATTERN cannot be
copied.
LOGO SCREEN
Sets whether or not to display the logo screen.
E
26
nOPTION
DATE/TIME SETTING
to select the date
or
Set the date and time. Press
and time, and press
or
to change the numerical
values.
Set the date in “Month/Day/Year” order.
Set the time on a 12-hour basis. (Factory default)
DATE/TIME FORMAT
Sets the date/time display format.
DATE...................MM/DD/YYYY
DD/MM/YYYY
YYYY/MM/DD
(YYYY: Year, MM: Month, DD: Day)
TIME....................Select 12- or 24-hour time.
SCHEDULE (See page 29.)
You can turn the power on/off and change the screen
brightness at a specified time.
INPUT SELECT
Select the input mode to be used in PC D-Sub input terminal,
PC/AV DVI-D input terminal, PC/AV HDMI input terminal and
PC RGB/AV component input terminals.
For D-SUB, select SET after selecting the input mode, and
MENU
then press
.
D-SUB and BNC cannot be set to AV COMPONENT at the
same time.
If D-SUB is set to AV VIDEO, the AV VIDEO input terminal
cannot be used for BNC.
AUDIO SELECT
Selects the terminal used to input audio signals in each input
mode.
INPUT SIGNAL (PC D-SUB/PC RGB)
If a computer connected to the PC D-sub/PC RGB input
terminal outputs any of the following resolutions, make a
selection from the following options.
480 LINES...........AUTO, 640x480 or 848x480
768 LINES...........AUTO, 1024x768, 1280x768, or 1360x768
1050 LINES.........1400x1050 or 1680x1050
ZOOM2 SPECIAL SETTING (See page 28.)
SCAN MODE (AV input)
Sets the scan mode used for AV mode input.
MODE1................Over-scan display
MODE2................Under-scan display
MODE3................Under-scan display when the input signal
is 1080i/p. Otherwise, over-scan display
*E
ven when MODE1 is selected, under-scan display is used when
the input signal is 1080i/p and the screen size is Dot by Dot.
POWER MANAGEMENT
POWER MANAGEMENT determines whether or not to
switch modes from no signal to the input signal standby
mode.
COLOR SYSTEM (AV S-VIDEO/AV VIDEO)
Select the color system of the AV equipment which is
connected to AV S-video and AV video input terminal. (AUTO
/ PAL / PAL-60 / SECAM / NTSC3.58 / NTSC4.43)
When AUTO is selected, the color system is automatically
set according to the input signal.
Menu Items
AUDIO OUTPUT (RCA)
Sets the volume of sound output from the audio output
terminals.
When set to VARIABLE 2, sound will not be output from the
built-in speaker or the external speaker terminal.
VARIABLE1.........You can adjust the volume using VOLUME.
VARIABLE2.........You can adjust the volume using VOLUME.
FIXED..................Fixes the sounds.
AUDIO LEVEL (STEREO MINI)
Selects the maximum audio input level of the audio input
terminal.
SELF ADJUST
On a PC D-SUB/PC RGB screen, specify whether to
perform screen adjustment automatically or not. When ON
is selected, the screen is automatically adjusted when its
resolution is 800 x 600 or higher and the timing of input
signals changes. “ADJUSTING” appears on the screen
during the adjustment. For images with black edges, etc.,
depending on the signal, adjustment may not be possible.
In this case select OFF. (Perform manual adjustment of the
screen.)
AUTO INPUT CHANGE
Specify whether to change inputs automatically. When ON is
selected and no signal is present in the selected input mode,
AUTO INPUT CHANGE automatically changes the selected
mode to another mode where a video signal is present.
When video signals exist in multiple input modes, the
switching priority is as follows:
PC D-SUB, PC HDMI, AV HDMI, AV COMPONENT and AV
VIDEO
When the PN-ZB01 (optional) is attached:
PC DVI-D, PC HDMI, PC D-SUB, PC RGB, AV DVI-D, AV
HDMI, AV COMPONENT, AV S-VIDEO and AV VIDEO
(Input mode switching may take 15 seconds or more,
depending on the connected equipment. Input signals
may not be detected properly and a priority may change,
depending on the connected equipment or video signals.)
TOUCH PANEL MODE (PC input)
When the resolution is 1920 x 1080, setting this to ON
improves touch panel tracking.
When two screens are displayed, or when V-POS or V-SIZE
is adjusted on the SCREEN menu, the screen may become
distorted. In this vent, set to OFF.
nPIP/PbyP
PIP MODES
Sets the display method.
OFF���������Displays one screen.
PIP�����������Displays a sub screen inside a main screen.
PbyP��������Displays a main screen and a sub screen in a line.
PbyP2������Displays a main screen which measures 1280 pixels
in the longest direction and a sub screen in a line.
PIP SIZE
Sets the size of the sub screen in PIP mode.
PIP H-POS
Adjusts the horizontal position of the sub screen in PIP mode.
PIP V-POS
Adjusts the vertical position of the sub screen in PIP mode.
PIP BLEND
In PIP mode, use this menu item to display the sub screen
transparently.
PIP SOURCE
Selects the input signal of the sub screen in PIP, PbyP, or
PbyP2 mode.
SOUND CHANGE
Sets the sound which is output in PIP, PbyP, or PbyP2 mode.
If the main screen is displayed as a full screen by the AUTO
OFF function, the sound for the main screen is output even
when the sound for the sub screen is specified.
MAIN POS
Sets the position of the main screen in PbyP or PbyP2 mode.
PbyP2 POS
Sets the position of the sub screen in PbyP2 mode.
AUTO OFF
Sets the display method when no signals for the sub screen
are input in PIP, PbyP, or PbyP2 mode.
MANUAL........ Displays a main screen and a black sub screen.
AUTO............. Displays the main screen as a full screen.
TIPS
• When WHITE BALANCE is set to THRU, BLACK LEVEL,
CONTRAST, TINT, COLORS, RGB INPUT RANGE,
GAMMA and COPY TO USER cannot be set.
• If COLOR MODE is set to sRGB, the following items cannot
be set.
WHITE BALANCE, PRESET, USER, COPY TO USER, and
GAMMA
• When the COLOR MODE is set to VIVID, GAMMA can not
be adjusted.
• STANDBY MODE cannot be set to LOW POWER when
SCHEDULE is effective or when OFF is selected for LED in
FUNCTION.
• When displaying the color pattern, it is possible to adjust
certain items of the PICTURE menu.
Non-adjustable items cannot be selected.
Audio input from the HDMI input terminal is also not output.
27
E
Menu Items
nDual screen display
You can display the screens of the PC input signal and AV
input signal simultaneously.
Set this function with “PIP MODES” in the PIP/PbyP menu.
PIP
A sub screen is displayed
inside a main screen.
Main screen
Sub
screen
PbyP
Main
screen
Sub
screen
PbyP2
Main screen
Sub
screen
A main screen and a sub
screen are displayed in a
line.
Displays a main screen
which measures 1280
pixels in the longest
direction and a sub
screen in a line.
* The currently selected input signal is displayed on the main
screen.
* You cannot simultaneously display the screens of signals
of the same type, such as two types of PC input signals or
two types of AV input signals.
* The dual screen display cannot be used with the
combination of PC DVI-D and AV HDMI or of AV DVI-D and
PC HDMI.
TIPS
• You might infringe on a copyright of the author which is
protected by copyright law when you display the images of
the computer screen and television/VCR simultaneously for
profit-making or to show the image to the public.
• The screen size for dual-screen display is the same as
the screen size for single-screen display. The Dot by Dot
screen is displayed in NORMAL size except when it is set
as the PIP main screen.
• When dual-screen display is selected, the SCREEN
MOTION function is disabled.
• When dual-screen display is selected, the AUTO INPUT
CHANGE function is disabled.
• When dual-screen display is selected, the INPUT SELECT
options cannot be set.
• When an interlaced signal (1080i, 480i, video, S-Video) is
input to the sub screen, horizontal lines may flicker. If this
happens, display the image on the main screen.
E
28
nZOOM2 SPECIAL SETTING
If you connect a laptop computer with any of the following
screen resolutions and black bands appear around the
screen, set ZOOM2 SPECIAL SETTING of INPUT SIGNAL on
the OPTION menu to ON and then select ZOOM2 in the SIZE
setting.
This displays the area inside the black band.
Laptop computer
resolution
Corresponding signal*1
1280x800
1280x1024, 1280x960, 1400x1050*2
1280x600
1280x720
1024x600
1024x768
*1: This setting is effective only when the screen resolution,
including the black band, is one of the resolutions listed
above.
*2: Use the automatic screen adjustment.
Menu Items
nSCHEDULE
Caution
You can set the time to switch the monitor on and off.
Set this function with “SCHEDULE” in the OPTION menu. (See
page 26.)
PC D-SUB
SCHEDULE
(2)
No. (1) POWER
–
–
–
–
–
–
–
–
––
––
––
––
––
––
––
––
– –/– –/– – – –
(3)
–––
DAY OF THE WEEK
–
–– - ––
–
–
–
–
–
–
–
1920x1080
––
––
––
––
––
––
––
-
––
––
––
––
––
––
––
V: 60 Hz
– –:– –:– – – –
(4)
TIME
––:––
––:––
––:––
––:––
––:––
––:––
––:––
––:––
––
––
––
––
––
––
––
––
(5)
INPUT
––
––
––
––
––
––
––
––
H: 67.5 kHz
(6)
BRIGHT
––
––
––
––
––
––
––
––
TIPS
OK···[MENU]
1. Press
or
to select the SCHEDULE number, and
press
.
2. Set the SCHEDULE. (See the description below.)
or
to select items, and press
Press
change the setting.
or
• Do not switch off the main power after setting the
SCHEDULE.
• Specify the correct date and time. (See page 26.)
SCHEDULE does not function unless the date and time are
specified.
• Check regularly that the set date and time are correct.
• When STANDBY MODE is LOW POWER, SCHEDULE
cannot be set.
• When a temperature abnormality occurs and the backlight
brightness is reduced, the brightness is not changed even
if a schedule set to BRIGHT is executed.
to
• Up to 8 SCHEDULE items can be registered.
• Setting the SCHEDULE flashes the power LED alternately
in red and orange in standby mode.
• A SCHEDULE that has a large number has precedence
over that of a small number when schedules overlap.
• If D-SUB of INPUT SELECT on the OPTION menu is set to
AV VIDEO, the input mode will switch to AV VIDEO (D-SUB)
regardless if set to D-SUB or VIDEO.
MENU
3. Press
.
SCHEDULE becomes effective.
(1)
●: SCHEDULE effective
-: SCHEDULE not effective
(2) POWER
ON : Switches the monitor on at the specified time.
OFF: Switches the monitor off at the specified time and puts
the monitor in standby mode.
(3) DAY OF THE WEEK
Specifies the day of the week to execute the SCHEDULE.
0:ONLY ONCE
Executes the SCHEDULE once on the specified day.
Specify the day of the week to execute the SCHEDULE.
1:EVERY WEEK
Executes the SCHEDULE on the specified day of the week
every week. Specify the day of the week to execute the
SCHEDULE.
Periodic setting such as “Monday through Friday” is also
possible.
2:EVERY DAY
Executes the SCHEDULE every day regardless of the day
of the week.
(4) TIME
Specifies the time to execute the SCHEDULE.
Set the time on a 12-hour basis. (Factory default)
Can be entered as 24-hour time using the TIME setting in
DATE/TIME FORMAT.
(5) INPUT
Specifies the input mode at power-on. When not specifying,
the screen at the previous power-off appears.
Input modes displayed on DVI, HDMI, BNC and D-SUB
depend on INPUT SELECT settings.
(6) BRIGHT
Sets the brightness when changing the screen brightness at
a specified time.
29
E
Menu Items
nADVANCED items (AV input) (See page 24
for additional Menu item details.)
FLESH TONE
Adjust the hue control.
3D-NR
Reduce the noise of playback images on video.
Setting a higher level reduces more noise. However, it may
cause blurring on an image.
MPEG-NR
Reduce block noise caused by digital compression.
3D-Y/C (AV VIDEO)
Specify whether to perform 3-dimension Y/C separation.
If dot interference or cross-color is occurring in fast-motion
scenes, selecting “OFF” may improve the image quality.
C.M.S.-HUE
Adjusts color tone with 6 colors of R (red), Y (yellow), G
(green), C (cyan), B (blue), and M (magenta).
C.M.S.-SATURATION
Adjusts color vividness with 6 colors of R (red), Y (yellow), G
(green), C (cyan), B (blue), and M (magenta).
C.M.S.-VALUE
Adjusts color brightness with 6 colors of R (red), Y (yellow),
G (green), C (cyan), B (blue), and M (magenta).
TIPS
• When FLESH TONE is set to LOW or HIGH, C.M.S.-HUE/
-SATURATION/-VALUE cannot be set.
Adjustments for PC screen display
nAutomatic adjustment
When you use the PC D-sub input terminal or PC RGB input
terminals to display a PC screen for the first time, or when
you change the setting of the PC, use the automatic screen
adjustment.
1. Switch the input to PC D-SUB or to PC RGB and display
the adjustment pattern. (See the description below.)
MENU
2. Press
and use
or
to display the SCREEN
menu.
3. Press
and select “AUTO”.
.
4. Press
The automatic adjustment is complete in several seconds.
5. Press MENU twice to close the menu screen.
TIPS
• If the screen cannot be adjusted properly with one
automatic adjustment, repeat the automatic adjustment two
or three times. Try manual adjustment if necessary.
nScreen display for adjustment
Before making adjustments in the SCREEN menu or
PICTURE menu, display an image to brighten the entire
screen. If you are using a Windows PC, use the adjustment
pattern on the supplied CD-ROM.
Opening the adjustment pattern
The following example is performed in Windows 7.
1. Load the supplied CD-ROM into the computer’s CDROM drive.
2. Open [CD Drive] in [Computer].
In Windows XP, open [CD Drive] in [My Computer].
3. Double-click [Adj_uty.exe] in the [Monitor] folder.
The adjustment pattern will appear.
Adjust the screen automatically or manually.
4. When adjustment is finished, press the [Esc] on the
computer’s keyboard to quit the adjustment program.
5. Eject the CD-ROM from the CD-ROM drive.
TIPS
• If the display mode on the computer you are using is
65,000 colors, the color levels in the color pattern may
appear differently or grayscale may appear to be colored.
(This is due to the specifications of the input signal and is
not a malfunction.)
E
30
Initialization (Reset)/Functional Restriction Setting (FUNCTION)
You can return the settings to their factory-preset values and
restrict operations.
SIZE
down until “F” appears in the upper left
1. Hold
corner of the screen.
,
,
,
in that
2. While “F” appears, press
order.
▲
▲
1/1
OFF
▲
UNLOCKED
ON1
ON
LED
OFF
MONITOR
▲▲▲▲▲▲
ALL RESET
ADJUSTMENT LOCK
ADJUSTMENT LOCK TARGET
RS-232C
OSD DISPLAY
LED
TEMPERATUREALERT
STATUSALERT
POWER BUTTON
CONTROLLER INPUT
▲▲▲▲▲▲
FUNCTION
END…[MENU]
3. Select and set the items.
ALL RESET
Resets the settings to the factory default settings.
MENU
, select ALL RESET, and then press
.
Press
After initialization, turn the main power switch off and
then back on.
When the PN-ZB01 (optional) is attached, press
,
MENU
.
select the resetting method, and then press
ALL RESET1����Resets all the settings to the factory
default settings.
ALL RESET2����Returns all settings to the factory default
settings except for the following items:
LAN SETUP, RS-232C/LAN SELECT,
ID No. SET, BAUD RATE, NETWORK,
MAIL, SERVICE & SUPPORT, and
SNMP (See page 26, and pages 47 to
50.)
ADJUSTMENT LOCK
You can disable operations on the monitor and the
remote control unit that use buttons.
OFF���Enables operation.
ON 1��Disables all operations other than turning power
on/off and FUNCTION.
ON 2��Only the FUNCTION operation is enabled.
Disables all operations other than FUNCTION (not
even power on/off).
ADJUSTMENT LOCK TARGET
Sets the target to prohibit operation of with
ADJUSTMENT LOCK.
REMOTE CONTROL����� Prohibits remote control
operation
MONITOR BUTTONS��� Prohibits monitor button
operation
BOTH����������������������������� Prohibits remote control and
monitor button operation
RS-232C
(RS-232C/LAN when the PN-ZB01 (optional) is
attached)
Specifies whether to allow control via RS-232C or LAN
(see pages 32 and 43).
OSD DISPLAY
Shows/hides the menu, modes, and messages.
The FUNCTION screen cannot be hidden.
ON 1�������������� Shows all menus, modes, and messages.
ON 2�������������� Hides messages automatically displayed
by the display. Shows messages during
operation.
OFF��������������� Hides all menus, modes, and messages.
LED
Specifies whether to light the power LED.
OFF cannot be selected when STANDBY MODE is LOW
POWER.
TEMPERATURE ALERT
Selects the notification method for an abnormal
temperature.
OFF�������������� Do not notify about an abnormal
temperature.
OSD & LED�� When an abnormal temperature is
detected, the power LED flashes in red
and green alternately and the screen
displays a message: TEMPERATURE.
LED�������������� When an abnormal temperature is
detected, the power LED flashes in red
and green alternately.
STATUS ALERT
Selects the notification method for a hardware error.
OFF�������������� Do not notify about the error.
OSD & LED�� When a hardware error is detected, the
power LED flashes in red and the screen
displays a message: STATUS [xxxx].
LED�������������� When a hardware error is detected, the
power LED flashes in red.
POWER BUTTON
Normally, leave this setting as MONITOR.
When using an optional part, if instruction appears,
change the setting accordingly.
CONTROLLER INPUT
Normally, you do not need to change this setting.
When using an optional part, if instruction appears,
change the setting accordingly.
4. Press
MENU
to return to the normal screen.
TIPS
• When both abnormal temperature and hardware error are
detected, the hardware error notification overrides.
• If TEMPERATURE ALERT or STATUS ALERT is set to
OSD&LED, alert messages will appear even if the OSD
DISPLAY is set to ON 2 or OFF.
31
E
Controlling the Monitor with a PC (RS-232C)
You can control this monitor from a PC via RS-232C (COM
port) on the PC.
You can also connect multiple monitors via a daisy chain by
using a PC. By assigning ID numbers to each monitor (see
page 33), you can make input mode selection/adjustment or
can check the status of a specific monitor.
Precautions when the PN-ZB01 (optional) is attached
• To control the monitor via RS-232C, set RS-232C/LAN
SELECT to RS-232C.
• You cannot use RS-232C and LAN control simultaneously.
PC connection
nOne-to-one connection with a PC
Connect with RS-232 straight cable between the PC’s COM
port (RS-232C connector) and the RS-232C input terminal on
the monitor.
Communication conditions
Set the RS-232C communication settings on the PC to match
the monitor’s communication settings as follows:
Baud rate
*
Stop bit
1 bit
Data length
8 bits
Flow control
None
Parity bit
None
* Set to the same baud rate as the BAUD RATE setting of
SETUP menu. (Initial setting: 38400 bps)
* When connecting multiple monitors in a daisy chain, set all
monitors to the same BAUD RATE.
Communication procedure
nCommand format
When a command is sent from the PC to the monitor, the
monitor operates according to the received command and
sends a response message to the PC.
Return code
C1
RS-232C input terminal
To COM port
nDaisy chain connection… Advanced operation
Connect with RS-232 straight cable between the PC’s COM
port (RS-232C connector) and the RS-232C input terminal on
the first monitor.
Next, connect RS-232 straight cable to the first monitor’s
RS‑232C output terminal and to the second monitor’s
RS-232C input terminal. Connect in the same way to the third
and subsequent monitors.
Up to 25 monitors can be connected. (Depending on the
length of the cable used and the surrounding environment.)
Second monitor
P1
P2
P3
P4
Parameter field
(4 character string comprised of:
0-9, +, -, space, ?)
Example: VOLM0030
VOLM
30
* Be sure to input 4 characters for the parameter. Pad with
spaces (“ ”) if necessary.
(“
” is a return code (0DH, 0AH or 0DH))
Wrong : VOLM30
Right : VOLM
30
When inputting a negative value, specify a numerical value in
three digits.
Example: AUTR-005
Do not use spaces for MPOS, DATE, and SC01 through
SC08. Specify parameters using a specified number of
characters.
Example: MPOS010097
If a command has “R” listed for “DIRECTION” in the
“RS-232C command table” on page 36, the current value can
be returned by using “?” as the parameter.
RS-232C
output terminal
Example:
RS-232C
input terminal
VOLM ? ? ? ?
←
From PC to monitor (How much
is current volume setting?).
30
←
From monitor to PC (Current
volume setting: 30).
* If an ID number (see page 33) has been assigned
(For example, ID number = 1).
PC
VOLM
30
To COM port
32
C4
RS-232 straight cable
(commercially available)
E
C3
Command field
(4 prescribed
alphanumerical characters)
PC
First monitor
C2
RS-232 straight cables
(commercially available)
001
?
← From PC to monitor.
← From monitor to PC.
Controlling the Monitor with a PC (RS-232C)
nResponse code format
When a command has been executed correctly
O
K
Return code
(0DH, 0AH)
A response is returned after a command is executed.
* If an ID number has been assigned
Return code
(0DH, 0AH)
Space (20H)
O
K
SPC
0
0
1
ID number of responding monitor
R
R
Interval of 100 ms or more
Return code
(0DH, 0AH)
INPS0001
WAIT
OK
* If an ID number has been assigned
Return code
(0DH, 0AH)
Space (20H)
E
R
R
SPC
0
0
1
TIPS
ID number
TIPS
• “ERR” is returned when there is no relevant command or
when the command cannot be used in the current state of
the monitor.
• If communication has not been established for reasons
such as a bad connection between the PC and monitor,
nothing is returned (not even ERR).
• “ERR” may be returned when a command cannot be
received correctly due to interference from the surrounding
environment.
Please ensure that the system or software retries the
command if this occurs.
• If no monitor has been assigned the designated ID number
(e.g. if the command IDSL0002
is used, but no monitor
with ID number: 2 is found), no response is returned.
If execution of the command is taking some time
W
A
I
T
Return code
(0DH, 0AH)
When the following commands are used, “WAIT” is returned.
In this case, a value will be returned if you wait a while. Do not
send any command during this period.
No ID number is attached to WAIT response.
• Commands which return WAIT:
1. When repeater control is used
2. When an IDSL or IDLK command is used
3. When one of the following commands is used: RSET,
INPS, ASNC, WIDE, PXSL, POWR, AGIN, MWIN,
MWIP, MWPP
When control via RS-232C is locked (to prevent use)
using the operation lock function (see page 31)
L
O
C
K
E
• After OK or ERR is returned, you must send the following
commands.
To set a timeout for the command response, specify 10
seconds or longer.
When connecting multiple monitors in a daisy chain, set the
timeout to at least the product of the monitor’s position from
the computer multiplied by 10 seconds.
Example) 3rd monitor from computer: 30 seconds or longer.
• Provide an interval of 100 ms or more between the
command response and the transmission of the next
command.
VOLM0020
OK
When a command has not been executed
E
nCommunication interval
D
Return code
(0DH, 0AH)
• When executing ALL RESET, set the timeout period to 30
seconds or longer.
• When turning the power on while the POWER ON DELAY
function is in use, set the timeout period to the POWER ON
DELAY period + 10 seconds or longer.
Advanced operation
This section explains commands for daisy chain connection.
The basic communication procedure is the same as in the
“One-to-one connection with a PC” section.
nID numbers
You can assign a unique ID number to each monitor (see
page 26). This allows you to control a particular monitor in a
daisy chain of monitors.
You can assign ID numbers either from the menu screen or
from the PC using RS-232 cable.
[Example]
ID number: 1
ID number: 2
ID number: 3
ID number: 4
If monitors are connected as shown above, you can
execute commands like “Set the volume of the monitor with
ID 4 to 20”.
When controlling monitors linked in a daisy chain by
designating ID numbers, you should basically avoid any
duplication of ID numbers.
ID numbers do not have to be assigned in ascending order
starting from the PC. They can also be connected as shown
below.
[Example]
ID number: 3
ID number: 2
ID number: 4
ID number: 1
When RS-232C/LAN SELECT is set to LAN
U
N
S
E
L
E
C
T
E
D
Return code
(0DH, 0AH)
33
E
Controlling the Monitor with a PC (RS-232C)
nCommands for ID control
The command examples shown on this page assume the
following connection and ID number set up.
ID number: 1
ID number: 2
ID number: 3
ID number: 4
IDST��������.A monitor receiving this command sets its own ID
number in the parameter field.
Example:
IDST0001
OK
001 ← The ID number of this monitor is set to 1.
IDLK��������The parameter of this command sets the ID
number of the monitor. The monitor is subject to all
subsequent commands.
Example:
← with ID number: 2.
WAIT
←
OK
002
ID number: 1
Sets volume of monitor with ID
← number: 2 to 30.*
WAIT
← Processing
OK
ID number: 2
ID number: 3
ID number: 4
OK
002
Sets volume of monitor with ID
← number: 2 to 20.*
IDST001 +
← ID setting command with repeater control
WAIT
OK
001
← “OK” response from ID number: 1
OK
002
← “OK” response from ID number: 2
OK
003
← “OK” response from ID number: 3
OK
004
← “OK” response from ID number: 4 (End)
IDSL��������The parameter of this command sets the ID number
of the monitor. The monitor is subject to the next
command.
Example:
IDSL0002
←
The next command is for the monitor
with ID number: 2.
WAIT
←
Searching for monitor with ID number:
2
OK
002
← Found monitor with ID number: 2
Sets volume of monitor with ID
number: 2 to 30.
VOLM0030
←
WAIT
← Processing
OK
002
OK response from monitor with ID
← number: 2
VOLM0020
← Sets volume to 20.
OK
← number: 1 (the one directly connected
001
The volume of the monitor with ID
to the PC) is set to 20.*
* The IDSL command is effective only once, for the
immediately succeeding command.
002
IDLK0000
← Canceling fixed ID number setting
WAIT
← Canceling IDLK
OK
002
← Cancelation complete
VOLM0010
OK
34
← Found monitor with ID number: 2
WAIT
You can automatically assign ID numbers by using the IDST
command with the Repeater control (see “Repeater control”
on page 35).
For example, using the command “IDST001+” automatically
sets the ID numbers, as shown below.
[Example]
E
Searching for monitor with ID number:
2
VOLM0030
VOLM0020
TIPS
Following commands are for the monitor
IDLK0002
001
The volume of the monitor with ID number:
← 1 (the one directly connected to the PC) is
set to 10. (IDLK is canceled.)
* The IDLK command remains effective until it is
canceled, or power is shut off.
IDCK��������Provides screen display of the ID number currently
assigned to a monitor, and the ID number currently
set for IDLK (if any).
Example:
(After executing IDLK0002)
IDCK0000
← (Parameter has no meaning.)
ID : 001 IDLK : 002
← number is also displayed on the
IDCK000 +
← Repeater control. (If a command
WAIT
ID : 001 IDLK : 000
ID : 002 IDLK : 000
ID : 003 IDLK : 000
ID : 004 IDLK : 000
Returned response. The ID
monitor screen.
is used with repeater control, ID
designation using IDSL or IDLK
is canceled.)
Controlling the Monitor with a PC (RS-232C)
nRepeater control
This system has a function to allow setting of multiple
monitors connected in a daisy chain using a single command.
This function is called repeater control. You can use Repeater
control function without assigning ID numbers.
[Example]
Set 1
Set 2
Set 3
Set 4
Setting of the GAMMA user data
nTo transfer the GAMMA user data
Use the user data transfer commands (UGRW, UGGW and
UGBW). For each of the R, G and B colors, divide the total
512 pieces of user data into 16 blocks, and transfer 32 pieces
of data with each command.
C1
C2
C3
Command field
* If monitors are connected as shown above, you can
execute a command like “Set all monitors’ input settings to
PC D-SUB”.
← Sets volume of all monitors to 30.
In repeater control, responses are returned by all the
connected monitors.
If you want to determine that a value has been returned by a
specific set, assign ID numbers to each monitor in advance.
When some monitors do not return their responses, the
probable cause is that the monitors could not receive the
command or command processing is not complete. Do not
send a new command.
Example: (When 4 monitors are connected, and
assigned ID numbers: 1 through 4)
VOLM030 +
001
OK
002
OK
003
OK
004
← If 4 monitors are connected in
a chain, reliable operation can
be ensured by sending a new
command only after a reply
has been returned by 4th (last)
monitor.
Example:
WAIT
20
002
30
003
30
004
…
Block number (01 to 16) Data field
S1
S2
Checksum field
One piece of data consists
of 4 digits.
Command Block number
32 pieces of data
Checksum
* If data is less than 4 digits, add a “0” (zero) to make it 4
digits.
* The checksum field is the character string (ASCII) data of
lower-order one byte which indicates the sum of the block
number and 32 pieces of data in hexadecimal (0 to F).
nSaving the GAMMA user data
Use the user data save command (UGSV) to save the
transferred user data in the monitor.
If the data is not saved, it will be cleared when:
• The main power switch is off
• STANDBY MODE is LOW POWER and the monitor enters
standby mode
nChecking the GAMMA user data
Use the user data read commands (UGRR, UGGR and
UGBR) to return 512 pieces of user data for each of the R,
G and B colors. Divide the data into 16 blocks and return 32
pieces of data with each command. The value to be returned
is not the value stored in the monitor, but the value in the
temporary memory for display. (These values are the same
when the user data save command (UGSV) above has been
sent.)
TIPS
VOLM ? ? ? +
001
P4
To activate the transferred user data, select USER for GAMMA
of the PICTURE menu, or send the corresponding RS-232C
command.
Repeater control can also be used for reading settings.
10
P3
nActivating the GAMMA user data
WAIT
OK
P2
UGRW 01000000010002 … 0031C0
Repeater control is achieved by setting the FOURTH
CHARACTER of the parameter to “+”.
VOLM030 +
P1
Example: To transfer the data of block 1 (0 to 31 levels)
of red (R) data
nRepeater control command
Example:
C4
Volume settings for all
monitors are returned.
• The user data is not initialized by RESET of the PICTURE
menu. To initialize the user data, use ALL RESET of the
FUNCTION menu.
The GAMMA user data initialize command (UGRS) allows
the initialization of the user data only.
TIPS
• If repeater control is used during ID designation (IDSL,
IDLK), the ID designation is canceled.
35
E
Controlling the Monitor with a PC (RS-232C)
RS-232C command table
How to read the command table
Command:
Command field (See page 32.)
Direction:
W When the “Parameter” is set in the parameter field (see page 32), the command functions as described
under “Control/Response Contents”.
R The returned value indicated under “Reply” can be obtained by setting “????”, “
?” or “???+”
(repeater control) in the parameter field (see page 32).
Parameter:
Parameter field (See page 32.)
Reply:
Response (Returned value)
*1:
“●” indicates a command which can be used in power standby mode regardless of the STANDBY MODE setting.
“○” indicates a command which cannot be used in power standby mode when STANDBY MODE is set to LOW POWER.
“–” indicates a command which cannot be used in power standby mode regardless of the STANDBY MODE setting.
*2:
PN-ZB01 (optional) limitations
(A) When PN-ZB01 (optional) is not attached, (B) When PN-ZB01 (optional) is attached.
○: The command can be used.
- : Error (ERR)
Power control/Input mode selection
Function
POWER CONTROL
Command
Direction
POWR
W
Parameter
Reply
0
1
R
Control/Response contents
*1
*2
(A) (B)
Switches to standby mode.
Returns from standby mode.
0 Standby mode
1 Normal mode
● ○ ○
2 Input signal waiting mode
INPUT MODE SELECTION
INPS
W
R
0
Toggle change for input mode. Terminals not selected in INPUT SELECT
cannot be selected.
○ ○
1
PC DVI-D
“ERR” when AV DVI-D is selected for DVI of INPUT SELECT.
-
2
PC D-SUB
“ERR” when other than PC D-SUB is selected for D-SUB of INPUT SELECT.
○ ○
3
AV COMPONENT (BNC) / AV COMPONENT (D-SUB)
“ERR” when other than PC RGB is selected for BNC of INPUT SELECT, and
when other than AV COMPONENT is selected for D-SUB of INPUT SELECT.
○ ○
4
AV VIDEO (BNC) / AV VIDEO (D-SUB)
6
PC RGB
“ERR” when AV COMPONENT is selected for BNC of INPUT SELECT.
7
AV DVI-D
“ERR” when PC DVI-D is selected for DVI of INPUT SELECT.
8
AV S-VIDEO
9
AV HDMI
“ERR” when PC HDMI is selected for HDMI of INPUT SELECT.
○
○
○ ○
10
PC HDMI
“ERR” when AV HDMI is selected for HDMI of INPUT SELECT.
○ ○
○
● ○ ○
- ○
-
-
1 PC DVI-D
2 PC D-SUB
3 AV COMPONENT
4 AV VIDEO
6 PC RGB
7 AV DVI-D
8 AV S-VIDEO
9 AV HDMI
10 PC HDMI
E
36
● ○ ○
Controlling the Monitor with a PC (RS-232C)
SCREEN menu
Function
Command
Direction
Auto
ASNC
W
CLOCK
CLCK
WR
PHASE
positioning
size
RESOLUTION
RESET
Parameter
Reply
Control/Response contents
1
When the input mode is PC D-SUB, PC RGB.
0-1200
0-1200 When the input mode is PC D-SUB, PC RGB.
Varies depending on the signal.
PHSE
WR
0-63
Position of the longest direction
HPOS
WR
0-100
0-100 0-800 on PC D-SUB, PC RGB.
Varies depending on the signal.
Position of the shortest direction
VPOS
WR
0-100
0-100 0-200 on PC D-SUB, PC RGB.
Varies depending on the signal.
Position of the longest direction
HSIZ
WR
0-100
0-100
Position of the shortest direction
VSIZ
WR
0-100
0-100
Longest direction resolution
HRES
WR
300-1920
300-1920 When the input mode is PC D-SUB, PC RGB.
Only even numbers are valid for parameters.
Varies depending on the signal.
Shortest direction resolution
VRES
WR
200-1200
200-1200
ARST
W
*1
*2
(A) (B)
0-63 When the input mode is PC D-SUB, PC RGB.
-
○ ○
1
37
E
Controlling the Monitor with a PC (RS-232C)
PICTURE menu
Function
Command
Direction
Auto
AGIN
W
1
When the input mode is PC D-SUB, PC RGB.
ANALOG GAIN
ANGA
WR
0-127
0-127 When the input mode is PC D-SUB, PC RGB.
ANALOG OFFSET
ANOF
WR
0-127
0-127 When the input mode is PC D-SUB, PC RGB.
CONTRAST
CONT
WR
0-60
0-60
BLACK LEVEL
BLVL
WR
0-60
0-60
TINT
TINT
WR
0-60
0-60
COLORS
COLR
WR
0-60
0-60
SHARPNESS
SHRP
WR
0-24
0-24
RGB INPUT RANGE (AV HDMI)
AHDR
WR
0-2
0-2 0: AUTO, 1: FULL, 2: LIMITED
RGB INPUT RANGE (PC HDMI)
PHDR
WR
0-2
0-2 0: AUTO, 1: FULL, 2: LIMITED
RGB INPUT RANGE (AV DVI)
ADVR
WR
1-2
1-2 1: FULL, 2: LIMITED
RGB INPUT RANGE (PC DVI)
PDVR
WR
1-2
1-2 1: FULL, 2: LIMITED
RGB INPUT RANGE (D-SUB)
PDSR
WR
1-2
1-2 1: FULL, 2: LIMITED
RGB INPUT RANGE (PC BNC)
PBRR
WR
1-2
1-2 1: FULL, 2: LIMITED
FLESH TONE
FLES
WR
0-2
0-2 0: OFF, 1: LOW, 2: HIGH
3D-NR
TDNR
WR
0-2
0-2 0: OFF, 1: LOW, 2: HIGH
MPEG-NR
MPNR
WR
0-1
0-1 0: OFF, 1: ON
3D-Y/C
YCSP
WR
0-1
C.M.S.-HUE
CMHR
WR
-10-10
ADVANCED
(When the input
mode is AV.)
Parameter
Reply
Control/Response contents
CMHY
Y
CMHG
G
CMHC
C
CMHB
B
WHITE BALANCE
THRU
W
CMSR
WR
1
-10-10
Y
CMSG
G
CMSC
C
CMSB
B
W
CMVR
WR
2
-10-10
Resets the saturation.
-10-10 R
CMVY
Y
CMVG
G
CMVC
C
CMVB
B
W
3
BMOD
WR
0
0 STD
2
2 VIVID
3
3 sRGB (When the input mode is PC)
0
0 When the input mode is PC DVI-D/PC HDMI.
WR
1-18
USER
99
Resets the brightness.
99
CRTR
WR
0-256
0-256 “ERR” when CTMP is not set to 99.
G-CONTRAST
CRTG
WR
0-256
0-256
B-CONTRAST
CRTB
WR
0-256
0-256
R-OFFSET
OFSR
WR
-127-127
-127-127
G-OFFSET
OFSG
WR
-127-127
-127-127
B-OFFSET
OFSB
WR
-127-127
-127-127
COPY TO USER
CPTU
W
GAMMA
GAMM
WR
WR
0
Copies a preset value to the user setting.
0-2
0-2 0: 1.8, 1: 2.2, 2: 2.4(during PC input)
0: LIGHT 2, 2: DARK (during AV input)
4-6
4-6 4: User, 5: 2.0, 6: STD (during PC input)
4: USER, 5: LIGHT 1, 6: STD (during AV input)
0
0 No pattern display.
1
1 White single color pattern display.
2
2 Red single color pattern display.
3
3 Green single color pattern display.
4
4 Blue single color pattern display.
PTDR
WR
0-15
0-15 “ERR” when PTDF is not set to 99.
GREEN
PTDG
WR
0-15
0-15
BLUE
PTDB
WR
0-15
0-15
RESET
ARST
W
38
○
-
○
99 Red/green/blue mixed color pattern display.
Set each color's level with RED, GREEN, BLUE.
RED
2
○
1-18 From 1: approximately 3,000K to 15: approximately 10,000K
(500K steps)
16: approximately 5,600K, 17: approximately 9,300K,
18: approximately 3,200K
R-CONTRAST
99
E
○
M
CRST
PTDF
○
M
CRST
PRESET
DISPLAY COLOR PATTERN
○
Resets the hue.
-10-10 R
CMSY
CTMP
○
M
CRST
CMVM
COLOR MODE
-
0-1 0: OFF, 1: ON (When the input mode is AV VIDEO)
CMSM
C.M.S.-VALUE
*2
(A) (B)
-10-10 R
CMHM
C.M.S.SATURATION
*1
-
○
Controlling the Monitor with a PC (RS-232C)
AUDIO menu
Function
Command
Direction
Parameter
Reply
Control/Response contents
TREBLE
AUTR
WR
-5-5
BASS
AUBS
WR
-5-5
-5-5
BALANCE
AUBL
WR
-10-10
-10-10
RESET
ARST
W
Command
Direction
OSD H-POSITION
OSDH
WR
0-100
0-100
OSD V-POSITION
OSDV
WR
0-100
0-100
SCREEN MOTION
SCSV
WR
0-4
0-4
MOTION TIME 1
MTIM
WR
0-20
0-20
*1
*2
(A) (B)
-5-5
○
3
○ ○
-
SETUP menu
Function
MOTION TIME 2
Parameter
Reply
Control/Response contents
PATTERN1
MINT
WR
10-990
10-990
MINT
WR
5-20
5-20
MONAURAL AUDIO
MONO
WR
0-1
0-1
LANGUAGE
LANG
WR
14
14
ENGLISH
1
1
DEUTSCH
2
2
FRANÇAIS
3
3
ITALIANO
4
4
ESPAÑOL
5
5
РУССКИЙ
6
6
PWOD
WR
0
0
1-60
1-60
Per 10 seconds
Per second
0: OFF, 1: ON
OFF
ON
STANDBY MODE
STBM
WR
0-1
0-1
0: STANDARD, 1: LOW POWER
(“ERR" when SCHEDULE is effective or OFF is selected for LED.)
OFF IF NO OPERATION
ATOF
WR
0-1
0-1
0: OFF, 1: ON
HOT PLUG CONTROL (DVI)
HPCT
WR
0-1
0-1
0: OFF, 1: ON
HOT PLUG CONTROL (HDMI)
HPCH
WR
0-1
0-1
0: OFF, 1: ON
RS-232C/LAN SELECT
CTLS
WR
0-1
0-1
0 : RS-232C 1 : LAN
ID NUMBER
IDST
W
ID NO. SETTING
0-255
R
Sets the monitor’s ID number. (“0” means “no ID number”.)
0-255
ID NO. SETTING
(ONCE)
IDSL
W
1-255
ID NO. SETTING
(SUBSEQUENT)
IDLK
W
1-255
ID CHECK
IDCK
W
Sets a monitor ID number.
This ID number is effective for the next and all subsequent commands
after this command.
Displays monitor’s own ID number and the selected ID number on the
screen.
BAUD RATE
BAUD
WR
0-2
0-2
0: 9600bps, 1: 19200bps, 2: 38400bps
SPSL
WR
0-1
0-1
0: Internal speaker, 1: External speaker
0: OFF, 1: ON
HDMI AUTO VIEW
HDAW
WR
0-1
0-1
SETTING COPY MODE
CPMD
WR
0
0
1-225
1-225
0
0
Copies the PICTURE menu settings.
1
1
Copies all the settings.
0-1
0-1
LOGO SCREEN
BTSC
WR
WR
○
○
○ ○
○
○
○
○ - ○
○ ○ ○
○ - ○
○ ○ ○
Clears the ID number if one has been designated.
ID
: xxx
IDLK : yyy
SPEAKER SELECT
CPTG
○
Returns the monitor’s ID number.
Clears the ID number if one has been designated.
0
SETTING COPY TARGET
○
○
Sets a monitor ID number.
This ID number is only effective for the command immediately after this
command.
0
0
*2
(A) (B)
○
0: OFF, 1-4: PATTERN1-4
PATTERN2-4
Power On Delay
*1
Copy to all monitors.
Copy to the monitor with the set ID Number.
○ ○ ○
○ - ○
○ ○ ○
○ ○ ○
0: OFF, 1: ON
39
E
Controlling the Monitor with a PC (RS-232C)
OPTION menu
Function
Command
Direction
Date/time setting
DATE
WR
AABBCCDDEE
AABBCCDDEE
AA: Year, BB: Month, CC: Day, DD: Time, EE: Minute
DATE DISPLAY FORMAT
DTFT
WR
0-2
0-2
0: YYYY/MM/DD, 1: MM/DD/YYYY, 2: DD/MM/YYYY
YYYY: Year, MM: Month, DD: Day
TIME DISPLAY FORMAT
TMFT
WR
0-1
0-1
0: 24-HOUR TIME, 1: 12-HOUR TIME
SCHEDULE
SC01SC08
WR
ABCDEFFGGH
ABCDEFFGGH
Schedule of a specified number
A: Schedule
0= Not effective, 1 = Effective
B: Power
0 = OFF, 1 = ON
C: Day of the week 1 0 = Only once, 1 = Every week, 2 = Every day
D: Day of the week 2 0 = Sunday, 1 = Monday through 6 = Saturday,
9 = Not exist
E: Day of the week 3 0 = Sunday, 1 = Monday through 6 = Saturday,
9 = Not exist
F: Time
00-23
G: Minute
00-59
H: Input
0 = Not specified, 1 = PC DVI-D/AV DVI-D,
2 = PC D-SUB, 3 = PC RGB/AV COMPONENT,
4 = AV VIDEO, 5 = AV S-VIDEO,
6 = PC HDMI/AV HDMI
“ERR” when LOW POWER is selected for STANDBY MODE.
SCHEDULE BRIGHTNESS
INPUT SELECT
AUDIO SELECT
SB01SB08
WR
DVI
DVSL
BNC
Parameter
Reply
0-31
Control/Response contents
*1
○ ○ ○
0-31 Screen brightness to change
99
99 Disable brightness setting
WR
0-1
0-1 0: PC DVI-D, 1: AV DVI-D
BNSL
WR
0-1
0-1 0: PC RGB, 1: AV COMPONENT
D-SUB
SLDS
WR
0-2
0-2 0: PC D-SUB, 1: AV COMPONENT, 2: AV VIDEO
HDMI
HDSL
WR
0-1
0-1 0: PC HDMI, 1: AV HDMI
PC DVI-D
ASDP
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
PC HDMI
ASHP
WR
0-1
0-1 0: HDMI, 1: AUDIO(STEREO MINI)
2-3
2-3 2: AUDIO1(RCA), 3: AUDIO2(RCA)
PC D-SUB
ASAP
WR
1-3
1-3 1: AUDIO(STEREO MINI)
PC RGB
ASCP
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
-
AV DVI-D
ASDA
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
-
AV HDMI
ASHA
WR
○ ○ ○ ○
○ ○
-
○
-
○
2: AUDIO1(RCA), 3: AUDIO2(RCA)
INPUT
RESOLUTION
(PC)
INPUT RESOLUTION (AV)
E
*2
(A) (B)
0-1
0-1 0: HDMI, 1: AUDIO(STEREO MINI)
2-3
2-3 2: AUDIO1(RCA), 3: AUDIO2(RCA)
-
○ ○
-
AV COMPONENT
(BNC)
ASCA
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
AV COMPONENT
(D-SUB)
ASC2
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
○
AV S-VIDEO
ASSA
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
-
AV VIDEO (BNC)
ASVA
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
AV VIDEO (D-SUB) ASV2
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
RESOLUTION CHECK
PXCK
R
PIXEL SETTING
(PC D-SUB, PC
RGB)
PXSL
WR
-
○
1 768) 1360 x 768
2
2 768) 1280 x 768
3
3 768) 1024 x 768
5
5 480) 848 x 480
6
6 480) 640 x 480
7
7 1050) 1680 x 1050
8
8 1050) 1400 x 1050
9
9 768) AUTO
10
10 480) AUTO
- 480i, 480p, 1080i, 720p, 1080p, VGA , etc.
-
○ ○
RESO
R
ZOOM2 SPECIAL SETTING
(PC D-SUB, PC RGB)
Z2SP
WR
0-1
0-1 0: OFF, 1: ON
○
SCAN MODE
SCAN
WR
0-2
0-2 0: MODE1, 1: MODE2, 2: MODE3 (When the input mode is AV)
POWER MANAGEMENT (PC)
PMNG
WR
0-1
0-1 0: OFF, 1: ON
POWER MANAGEMENT (AV)
PMAV
WR
0-1
0-1 0: OFF, 1: ON
COLOR SYSTEM
CSYS
WR
0-5
0-5 0: AUTO, 1: PAL, 2: PAL-60, 3: SECAM, 4: NTSC3.58, 5: NTSC4.43
AUDIO OUTPUT(RCA)
AOUT
WR
0-2
0-2 0: VARIABLE1, 1: FIXED, 2: VARIABLE2
AUDIO LEVEL(STEREO MINI)
AIVP
WR
0-1
0-1 0: 1.0Vrms, 1: 0.5Vrms
SELF ADJUST
AADJ
WR
0-1
0-1 0: OFF, 1: ON
AUTO INPUT CHANGE
AINC
WR
0-1
0-1 0: OFF, 1: ON
TOUCH PANEL MODE
GMDP
WR
0-1
0-1 0: OFF, 1: ON (When the input mode is PC)
○
○
○
○ ○ ○
○
○
○ ○ ○
○
○
40
RESOLUTION CHECK
-
- Returns current resolution in the form of hhh, vvv.
1
○
-
Controlling the Monitor with a PC (RS-232C)
PIP/PbyP menu
Function
Command
Direction
PIP MODES
MWIN
WR
0-3
PIP SIZE
MPSZ
WR
1-64
PIP POS
The longest direction
MHPS
The shortest direction
MVPS
PIP POS LD+SD BATCH
W
Parameter
Reply
0-100
0-100
R
MPOS
W
0-100
0-100,0-100
R
PIP BLEND
MWBL
WR
PIP SOURCE
MWIP
WR
0-3 0: OFF, 1: PIP, 2: PbyP, 3: PbyP2
1-64
0-100
R
W
Control/Response contents
Specify the position in MPOSxxxyyy format.
(xxx: Longer side, yyy: Shorter side position)
0-100,0-100 Returns a response in (xxx,yyy) format.
(xxx: Longer side, yyy: Shorter side position)
0-15
0-15
1
1 PC DVI-D
2
2 PC D-SUB
3
3 AV COMPONENT (BNC) / AV COMPONENT (D-SUB)
4
4 AV VIDEO (BNC) / AV VIDEO (D-SUB)
6
6 PC RGB
7
7 AV DVI-D
8
8 AV S-VIDEO
9
9 AV HDMI
10
10 PC HDMI
SOUND CHANGE
MWAD
WR
1-2
1-2 1: MAIN, 2: SUB
MAIN POS (Main screen)
MWPP
WR
0-1
0-1 0: POS1, 1: POS2
PbyP2 POS (Sub screen)
MW2P
WR
0-2
0-2 0: POS1, 1: POS2, 2: POS3
AUTO OFF
MOFF
WR
0-1
0-1 0: MANUAL, 1: AUTO
*1
*2
(A) (B)
○
○
○
○
○
○ ○ ○
○
○
○
- ○
○ ○
○ ○
○ ○
○ - ○
- ○
- ○
○ ○
○ ○
○
○
○ ○
○
○
Initialization/Functional Restriction Setting (FUNCTION) menu
Function
ALL RESET
Command
Direction
RSET
W
Parameter
Reply
0
0-1
Control/Response contents
*1
0: ALL RESET
-
0: ALL RESET 1, 1: ALL RESET 2
-
ADJUSTMENT LOCK
ALCK
WR
0-2
0-2 0: OFF, 1:ON1, 2:ON2
ADJUSTMENT LOCK TARGET
ALTG
WR
0-2
0-2 0: REMOTE CONTROL, 1: MONITOR BUTTONS, 2: BOTH
OSD DISPLAY
LOSD
WR
0-2
0-2 0: ON1, 1: OFF, 2: ON2
LED
OFLD
WR
0-1
0-1 0: ON, 1: OFF
“ERR” when LOW POWER is selected for STANDBY MODE.
TEMPERATURE ALERT
TALT
WR
0-2
0-2 0: OFF, 1: OSD & LED, 2: LED
STATUS ALERT
SALT
WR
0-2
0-2 0: OFF, 1: OSD & LED, 2: LED
POWER BUTTON
PBTN
WR
0-1
0-1 0: MONITOR, 1: CONTROLLER
CONTROLLER INPUT
PCIP
WR
0-2
0-2 0: D-SUB, 1: HDMI (“ERR” when MONITOR is selected for POWER
BUTTON.)
2: DVI-D (“ERR” when MONITOR is selected for POWER BUTTON.)
*2
(A) (B)
○
-
-
○
○
○
○
○ ○ ○
○
○
○
○ ○ ○
○ - ○
41
E
Controlling the Monitor with a PC (RS-232C)
Others
Function
Command
Direction
SCREEN SIZE (PC)
WIDE
WR
1-5
1-5 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2
SCREEN SIZE (AV)
WIDE
WR
1-5
1-5 1: WIDE, 2: ZOOM1, 3: ZOOM2, 4: NORMAL, 5: Dot by Dot
VOLUME
VOLM
WR
0-31
MUTE
MUTE
WR
0-1
MODEL
INF1
R
SERIAL NO
INFORMATION
SRNO
R
BRIGHT
VLMP
WR
TEMPERATURE SENSOR
DSTA
R
Parameter
Reply
Control/Response contents
0-31
0-1 0: OFF, 1: ON
○
○
○
*2
(A) (B)
-
Value
●
Value
0-31
*1
0-31
0 Internal temperature normal
○
1 Internal temperature abnormal (Standby mode)
2 Internal temperature abnormal (Temperature is normal now, but it was
abnormal during operation.)
●
3 Internal temperature abnormal (Brightness of the backlight decreases.)
4 Temperature sensor abnormal
Temperature acquisition
CAUSE OF LAST STANDBY MODE
ERRT
STCA
R
Value Temperature at temperature sensors 1 through 3 are returned in the
following forms:
[Sensor 1], [Sensor 2], [Sensor 3]
Indicates a temperature sensor abnormality when “126” is returned.
W
0
○ ○
○
Initialization
R
0 No detectable error has occurred
1 Standby mode by POWER button
2 Main power off by the main power switch
3 Standby mode by RS-232C or LAN
4 Waiting mode by No Signal
●
6 Standby mode by abnormal temperature
8 Standby mode by SCHEDULE setting
20 Standby mode by OFF IF NO OPERATION setting
Commands for setting of the GAMMA user data
Function
E
Command
Direction
RED GAMMA DATA TRANSFER
UGRW
W
GREEN GAMMA DATA TRANSFER
UGGW
W
BLUE GAMMA DATA TRANSFER
UGBW
W
RED GAMMA DATA READ
UGRR
W
GREEN GAMMA DATA READ
UGGR
W
Parameter
Reply
aaxxxx ··· xxxxcc
(xxxx: 32 pieces)
aa: 01-16
xxxx: 0000-1023
cc: 00-FF
1-16 xxxx ··· xxxx
1-16 (xxxx: 32 pieces)
xxxx: 0000-1023
1-16
Control/Response contents
*2
(A) (B)
aa: Block number
xxxx: 32 pieces of user data
cc: Checksum (ASCII data) of the block number and user data
xxxx: User data of 32 pieces
BLUE GAMMA DATA READ
UGBR
W
USER DATA INITIALIZE
UGRS
W
0
Initialize the user data.
USER DATA SAVE
UGSV
W
0
Save the user data in the monitor.
42
*1
○ ○ ○
Controlling the Monitor with a PC (LAN)
When the PN-ZB01 (optional) is attached, your monitor can
be connected to a LAN allowing you to control it from a PC on
the LAN.
You can also configure the monitor to send e-mail notification
when it has a problem.
The connection requires a commercially available LAN cable
(UTP cable, Category 5, straight through).
Network (LAN)
Settings to connect to a LAN
Set the monitor’s IP address and subnet mask to match the
settings of your LAN.
These settings can be made on either the monitor or a PC
connected to the monitor.
The settings depend on the configuration of your LAN. Ask
your LAN administrator for details.
■ To set on the monitor
Set RS-232C/LAN SELECT on the SETUP menu to LAN, and
then set the LAN SETUP options. (See page 26.)
MENU
After setting each item, select SET and press
.
LAN terminal
Hub
LAN cable (commercially available, straight)
TIPS
• You must assign an IP address to the monitor by following
the procedures in “Settings to connect to a LAN”. (See the
description on the right.)
• Your PC must be installed with Internet Explorer (version 7.0
or later).
• To control the monitor via LAN, set RS-232C/LAN SELECT
to LAN. (See page 26.)
• You cannot use RS-232C and LAN control simultaneously.
Initializing personal information
• When the PN-ZB01 (optional) is attached, personal
information such as e-mail addresses can be registered in
the monitor. Before transferring or disposing of the monitor, initialize all settings by selecting ALL RESET 1. (See
page 31.) Note that ALL RESET 2 will not initialize e-mail
addresses and other settings.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to ON.
To set the address manually, set this to OFF.
IP ADDRESS
If the DHCP CLIENT is set to OFF, specify an IP address.
Press
or
to select items, and press
or
to
change the values.
SUBNET MASK
If the DHCP CLIENT is set to OFF, specify the subnet mask.
Press
or
to select items, and press
or
to
change the values.
DEFAULT GATEWAY
If the DHCP CLIENT is set to OFF, specify the default
gateway.
If you are not using a gateway, specify “0.0.0.0”.
Press
or
to select items, and press
or
to
change the values.
RESET
Resets the values of the LAN settings to the factory preset
values.
MENU
Select ON and then press
.
TIPS
• When the IP address is set manually, the IP addresses of
the monitor connected to the RS-232C output terminal and
the daisy chain of connected monitors that follows can be
assigned automatically. (See page 26.)
43
E
Controlling the Monitor with a PC (LAN)
■ To set from a PC
When the monitor is connected to a PC, LAN settings can be
configured via PC.
Set up process
(1) Connect your monitor to a PC
(2) Specify the PC’s IP address
(3) Configure the monitor’s LAN settings
7. Temporarily change the IP address and subnet mask.
To access the monitor as it is shipped from the factory, set
as follows.
• IP Address: 192.168.150.1
• Subnet Mask: 255.255.255.0
• Default Gateway: (leave blank)
(1) Connecting your monitor to a PC
Connect a commercially available crossover LAN cable
(UPT cable, Category 5) to the LAN port on the PC and this
monitor.
8. Click [OK] and then reboot the PC.
LAN terminal
TIPS
PC
To LAN terminal
LAN cable
(commercially available, crossover)
(2) Specifying the PC’s IP address
To configure the monitor’s LAN settings, you must temporarily
change the settings on the PC.
This explanation is based on Windows 7.
1. Log on to the PC with an administrator account.
2. Click [Start], and then click “Control Panel”.
3. Click “View network status and tasks” in “Network and
Internet”.
In “Classic View”, click “Network and Sharing Center”.
4. Click “Local Area Connection” and then “Properties”.
5. Click “Internet Protocol Version 4 (TCP/IPv4)” and then
“Properties”.
6. Make a note of the current IP address, subnet mask, and
default gateway settings.
Make sure you write this information now as you will
be changing the IP address, subnet mask, and default
gateway settings back to these settings afterwards.
E
44
• This monitor is factory preset as shown below.
(When DHCP CLIENT is set to OFF)
IP Address
: 192.168.150.2
Subnet Mask
: 255.255.255.0
Default Gateway : 0.0.0.0
(3) Configuring the monitor’s LAN settings
Access the monitor using Internet Explorer.
Controlling the monitor
1. Turn the power ON to the monitor.
2. Set RS-232C/LAN SELECT on the SETUP menu to LAN.
3. Set DHCP CLIENT to OFF in LAN SETUP on the SETUP
menu.
PC operation
4. Launch Internet Explorer, in the “Address” box type
“http://192.168.150.2/” and press the Enter key.
You will be prompted to enter a user name and password.
5. Leave the user name and password boxes blank and click
[OK].
Controlling the Monitor with a PC (LAN)
6. Click on “LAN SETUP” under NETWORK.
Controlling with a PC
■ Basic operation
You use Internet Explorer on a PC on the LAN to control the
monitor.
1. Launch Internet Explorer on the PC.
2. In the “Address” box, type “http://” followed by your monitor’s
IP address followed by “/”, then press the Enter key.
You can confirm the IP address with the DISPLAY function.
7. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to “ON”.
To set the address manually, set this to “OFF”.
IP ADDRESS
If the DHCP CLIENT is set to “OFF”, specify an IP address.
SUBNET MASK
If the DHCP CLIENT is set to “OFF”, specify the subnet mask.
DEFAULT GATEWAY
If the DHCP CLIENT is set to “OFF”, specify the default gateway.
If you are not using a default gateway, specify “0.0.0.0”.
8. When the setting is changed, click [Apply].
9. Check the message and click [OK].
10.Exit Internet Explorer.
11.Restore the PC’s IP address jotted in Step 6, “(2)
Specifying the PC’s IP address”.
12.Connect the monitor and the PC to the LAN.
When prompted to enter a user name and password, type
the user name and password that you specified in the
security settings (see page 47), and click [OK].
If you did not make any security settings, leave the spaces
blank and click on [OK].
3. You can check, control, and change the monitor’s status
and settings by clicking the menu items on the left side of
the screen.
• If you see an [Apply] button next to a setting, click it after
you change that setting.
TIPS
• See pages 46 to 50 for details on each setting.
• If you click [Refresh] before the screen finishes updating
the current display, the “Server Busy Error” will appear.
Wait for a moment before operating your monitor again.
• You cannot operate the monitor while it is warming up.
DISPLAY
• If “DHCP CLIENT” is set to “ON”, press
on the
remote control unit two times and then check the monitor’s
IP address.
Caution
• Wait 10 seconds after clicking [OK] before proceeding.
• When operating using the remote control unit or similar,
click [Refresh].
TIPS
• When the IP address is set manually, the IP addresses of
the monitor connected to the RS-232C output terminal and
the daisy chain of connected monitors that follows can be
assigned automatically. (See page 26.)
45
E
Controlling the Monitor with a PC (LAN)
■ INFORMATION
Information about this monitor appears.
■ ADJUSTMENT
You can adjust these settings which are also available on the
monitor’s menu.
• SCREEN (See page 24.)
• PICTURE (See page 24.)
• PICTURE (ADVANCED) (See page 30.)
• AUDIO (See page 25.)
• SETUP (See page 25.)
• OPTION (See page 26.)
• SCHEDULE (See page 29.)
• PIP/PbyP (See page 27.)
• FUNCTION (See page 31.)
■ CONTROL
You can control the operations corresponding to the buttons
POWER INPUT SIZE
(
) on the remote control unit. (See page 21.)
TIPS
• After changing DISPLAY COLOR PATTERN to OFF, click
[Refresh] to correctly retrieve the status of the monitor.
TIPS
• In standby mode, Power ON is the operation available.
E
46
Controlling the Monitor with a PC (LAN)
■ NETWORK (LAN SETUP)
This screen allows you to set the settings necessary when the
monitor is connected to a LAN.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to “ON”.
To set the address manually, set this to “OFF”.
IP ADDRESS
If the DHCP CLIENT is set to “OFF”, specify an IP address.
SUBNET MASK
If the DHCP CLIENT is set to “OFF”, specify the subnet
mask.
DEFAULT GATEWAY
If the DHCP CLIENT is set to “OFF”, specify the default
gateway.
If you are not using a default gateway, specify “0.0.0.0”.
DNS SERVER
Specify the DNS server address.
If you are not using a DNS server, specify “0.0.0.0”.
RESET
Clicking [Execute] returns all of the LAN SETUP settings
to the factory-preset values except for the DNS SERVER
setting.
■ NETWORK (SECURITY)
This screen allows you to specify the security-related settings.
USER NAME / PASSWORD
Sets up a user name and password to restrict access to this
monitor.
After entering a user name and password, click [Apply].
ACCEPT IP ADDRESS
You can limit access to this monitor by registering IP
addresses of PCs that should have access.
To limit access, specify the option “From only specific IP
addresses”. Otherwise, to allow access from any PC, specify
“All IP Addresses”.
IP ADDRESS 1 to 3
If “ACCEPT IP ADDRESS” is set to “From only specific IP
addresses”, enter the IP addresses that you want to allow.
TIPS
• The USER NAME and PASSWORD can be up to 8
alphanumeric characters or symbols.
• To cancel the user name and/or password after it has been
set, make the box empty and click [Apply].
TIPS
• When the IP address is set manually, the IP addresses of
the monitor connected to the RS-232C output terminal and
the daisy chain of connected monitors that follows can be
assigned automatically. (See page 26.)
47
E
Controlling the Monitor with a PC (LAN)
■ NETWORK (GENERAL)
This screen allows you to specify the general LAN settings.
MONITOR NAME
Specify a name for this monitor as it should appear on the
Internet Explorer screen.
AUTO LOGOUT TIME
Specify the time (in minutes) to elapse before automatically
disconnecting this monitor from the network.
Specify in minutes from 1 to 65535. A value of ‘0’ will disable
this function.
DATA PORT
Specify the TCP port number to use for exchanging data with
the monitor.
Specify a value from 1025 to 65535.
SEARCH PORT
Specify the port number to use when searching for this
monitor.
Specify a value from 1025 to 65535.
INSTALLATION INFORMATION (NAME/LOCATION)
Specify the information to display for this monitor in the
Internet Explorer window.
TIPS
• The MONITOR NAME can be up to 16 alphanumeric
characters or symbols.
• Enter up to 50 characters in the NAME field in the
INSTALLATION INFORMATION.
• Enter up to 100 characters in the LOCATION field in the
INSTALLATION INFORMATION.
E
48
■ MAIL (ORIGINATOR)
This screen allows you to configure the e-mail sent periodically
or when the monitor has an error.
The settings depend on the configuration of your LAN. Ask
your LAN administrator for details.
SMTP SERVER
Specify the SMTP server address for sending e-mail.
* When using a domain name, make sure to specify the
DNS server as well. (See page 47.)
ORIGINATOR E-MAIL ADDRESS
Specify the e-mail address for this monitor.
This address becomes the e-mail address of the originator.
ORIGINATOR NAME
Specify the name for the originator.
This name appears in the “Originator Name” field of the
e-mail.
AUTHENTICATION
Specify the authentication method to use when sending
e-mail.
POP SERVER
If the “AUTHENTICATION” method is “POP before SMTP”,
specify the POP server address.
ACCOUNT NAME / PASSWORD
If the “AUTHENTICATION” method is “POP before SMTP”,
specify the account name and password to connect to the
POP server.
TIPS
• You can enter up to 64 alphanumeric characters or symbols
for the ORIGINATOR E-MAIL ADDRESS, ORIGINATOR
NAME, ACCOUNT NAME, and PASSWORD.
• The SMTP SERVER and POP SERVER can be up to 64
characters.
The following characters can be used: a-z, A-Z, 0-9, - , .
Controlling the Monitor with a PC (LAN)
■ MAIL (RECIPIENT)
This screen allows you to specify the recipients of the e-mail
sent periodically or when the monitor has an error.
RECIPIENT E-MAIL ADDRESSES
Specify the e-mail addresses to send error notification e-mail
to.
CONDITION
Specify the conditions to send mails.
When you check PERIODICAL, specify the date and time to
send the mails in the PERIODICAL setting.
CONFIRMATION
Sends test e-mail.
This allows you to confirm that the e-mail settings are
configured properly.
Attach the log file to a TEMPERATURE/HARDWARE error
e-mail.
When this option is checked, a log is added to the mail which
notifies a temperature or status error.
■ MAIL (PERIODICAL)
When PERIODICAL for CONDITION of MAIL (RECIPIENT) is
checked, set the date and time to send the mail.
DAY OF THE WEEK
Specify the day of the week to send the periodical mails.
TIME
Specify the time of the day to send the periodical mails.
Caution
• Do not turn off the main power when you set to send the
periodical mails.
• Specify the correct date and time. (See page 26.)
If the date and time settings are incorrect, the periodical
mail is not sent properly.
• Regularly confirm that the specified date and time is
correct.
• When LOW POWER is selected for STANDBY MODE,
periodical mails will not be sent in standby mode.
TIPS
• The RECIPIENT E-MAIL ADDRESSES can be up to 64
alphanumeric characters or symbols.
49
E
Controlling the Monitor with a PC (LAN)
■ SNMP
You can configure settings related to SNMP.
Caution
• After you set SNMP, click [Switch the main power of
monitor off and on now.] or turn off the monitor and then
turn it on again with the main power switch. When the
monitor restarts, wait about 30 seconds and then start the
next operation.
• If the IP address is changed while the SNMP function is
operational, turn off the monitor and then turn it on again
with the main power switch.
TIPS
• Depending on the SNMP settings, a short delay may occur
before the SNMP is usable. (About 2 minutes)
• Up to 16 alphanumeric letters and symbols can be used for
the community name, user name and password.
■ SERVICE & SUPPORT
(URL INFORMATION)
You can display a specific URL in the URL INFORMATION
field on the INFORMATION screen when an error occurs in
the monitor. (See page 46.)
SNMP SETTING
Set whether to enable or disable SNMP.
VERSION
Set the version of the SNMP to be supported.
COMMUNITY NAME 1 to 3
Set the name of the community required for the access.
USER 1 to 3
Set the user name, password, authentication method and
other options required for access.
TRAP SETTING
Set whether to enable or disable the trap function.
When this function is enabled, a trap will be sent when the
monitor is turned on.
TRAP SETTING OF AUTHENTICATION ERROR
Set whether the trap function sends a notification when
authentication fails.
TRAP ADDRESS & PORT
Set the destination address and port number of the
notification sent by the trap function.
E
50
URL INFORMATION
Enter the URL to display on the INFORMATION screen when
an error occurs on the monitor.
Up to 64 alphanumeric characters or symbols can be used.
CONDITION
Specify the condition to display the URL.
CONFIRMATION
The home page of the specified URL is displayed.
You can check whether the URL you entered is correct.
TIPS
• It is also possible to specify the message text, such as the
name of a contact or a telephone number, to be displayed
instead of the linked URL.
Troubleshooting
If you are experiencing any problem with your display, before
calling for service, please review the following troubleshooting
tips.
There is no picture or sound.
• Is the power cord disconnected? (See page 14.)
• Is the main power switch off? (See page 16.)
• Is the monitor in standby mode (the power LED illuminating
in orange)? (See page 16.)
• Make sure correct input mode is selected. (See page 21.)
• If any external equipment is connected, make sure the
equipment is operating (playing back).
The video from PC D-SUB, PC RGB, AV COMPONENT, or
AV VIDEO does not appear correctly.
• Is the setting for BNC or D-SUB of INPUT SELECT on the
OPTION menu correct? (See page 26.)
• Is the input signal compatible with this monitor? (See page
55.)
Control buttons do not work.
There is no picture.
• Load noises from outside may be interfering with normal
operation. Turn off the power and turn it on after waiting at
least 5 seconds, and then check the operation.
Remote control does not work.
• Are the batteries inserted with polarity (+,-) aligned? (See
page 15.)
• Are the batteries exhausted?
• Point the remote control unit toward the monitor’s remote
control sensor. (See page 15.)
• Is the menu display hidden or is operation disabled? (See
page 31.)
The input mode changes automatically.
• When the AUTO INPUT CHANGE is ON and no signal
is present in a selected input mode, the AUTO INPUT
CHANGE automatically changes the selected mode to a
mode where a video signal is present.
The input mode may change in the following cases:
-When a computer is in standby mode.
-When video play is stopped with a playback device.
Sound from left and right speakers is reversed.
Sound is heard from only one side.
• Are audio cables connected properly? (See pages 12 to
13.)
• Make sure audio cables for external speakers are
connected properly: left and right cables may be reversed
or one of the two cables may not be connected. (See page
13.)
• Check the setting of BALANCE for AUDIO menu. (See
page 25.)
The touch panel does not respond.
• Is the USB cable connected properly? (Touch Panel Driver
Operation Manual)
• Has the touch panel driver been installed? (Touch Panel
Driver Operation Manual)
• Has the pen tip of the touch pen become worn? Replace
the pen tip. (See page 20.)
• Is the battery inserted in the wrong orientation (+, -) in the
touch pen? (See page 18.)
• Is the touch pen battery exhausted?
There is a picture but no sound.
• Is the sound muted?
• Make sure the volume is not set to minimum.
• Are audio cables connected properly?
• Is the setting of AUDIO SELECT on the OPTION menu
correct? (See page 26.)
• Is the setting of SPEAKER SELECT on the SETUP menu
correct? (See page 26.)
The response of the touch screen is slow.
Some parts of the screen do not respond.
• Is the screen exposed to direct sunlight or other strong
light? The touch panel uses infrared rays and thus may not
operate correctly.
• Is there an obstacle between the infrared transmitter/
receiver and the touch pen or your finger? An obstacle
will prevent correct operation. If your fingers or a sleeve
are too close to the screen, correct operation will not be
possible.
• Is the infrared transmitter/receiver dirty? Gently wipe off
any dirt with a soft cloth.
• If the touch panel is touched with a small tip less than about
3/16 inch (4 mm) x 3/16 inch (4 mm), the touch may not
be detected by infrared and correct operation will not take
place.
• When starting your computer or connecting the USB cable,
do not touch the touch panel. If you touch the touch panel,
this may be detected as an element failure in the infrared
transmitter/receiver and incorrect operation will result.
Unstable video.
• The signal may be incompatible.
• Try the automatic screen adjustment when the PC D-sub
input terminal or PC RGB input terminals are used.
• If the top and bottom of the image are not horizontally
aligned, set TOUCH PANEL MODE on the OPTION menu
to OFF.
The video from the PC/AV HDMI input terminal does not
appear properly.
• Is the setting for HDMI of INPUT SELECT on the OPTION
menu correct? (See page 26.)
• Is the HDMI cable HDMI standard compliant? The monitor
will not work with cables that are not standard compliant.
• Is the input signal compatible with this monitor? (See page
55.)
The video from the PC/AV DVI-D input terminal does not
appear properly.
• Is the setting for DVI of INPUT SELECT on the OPTION
menu correct? (See page 26.)
• Is the input signal compatible with this monitor? (See page
55.)
• Turn off the power to the connected equipment and then
turn the power on again.
• If the monitors are connected in a daisy chain, turn off the
power to all the monitors connected in a daisy chain and
then turn the power on again.
Power LED flashes red.
“STATUS [xxxx]” appears in the corner of the screen.
• Hardware has a problem. Turn off the monitor and request
repair from your SHARP dealer.
(When STATUS ALERT is set to OSD & LED. This varies
depending on the setting.)
The touch panel power LED lights red.
• Hardware has a problem. Turn off the monitor and request
repair from your SHARP dealer.
51
E
Troubleshooting
When “AUTO DIMMING” is displayed.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight automatically
decreases in order to prevent a further temperature rise. If
you attempt to use
to adjust the brightness while
the monitor is in this state, “AUTO DIMMING” is displayed
and you cannot change the brightness.
• Remove the cause of the excessive temperature rise.
The monitor makes a cracking sound.
• You may occasionally hear a cracking sound from the
monitor. This happens when the cabinet slightly expands
and contracts according to change in temperature. This
does not affect the monitor’s performance.
The Power LED is flashing in red and green alternately.
When “TEMPERATURE” is displayed in the corner of the
screen.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight decreases
automatically in order to prevent high-temperaturerelated problems. When this occurs, “TEMPERATURE” is
displayed on the screen and the Power LED flashes red
and green alternately. (When TEMPERATURE ALERT is
set to OSD & LED. This varies depending on the setting.)
• If the internal temperature rises further, the monitor
automatically enters standby mode. (The Power LED
continues flashing red and green alternately.)
• Remove the cause of the excessive temperature rise.
- If the monitor enters standby mode due to a rise in
temperature, to return to normal display, turn the power
switch off and then back on again. The monitor, however,
will enter standby mode again if the cause of the
temperature rise is not eliminated. (See page 8.)
- Check whether the monitor is placed at a location where
a quick rise in temperature is likely. Internal temperature
rises quickly if the vents on the monitor are blocked.
- Internal temperature rises quickly if dust accumulates
inside the monitor or around the vents. Remove dust if
possible. Ask SHARP dealer about removing internal dust.
E
52
Specifications
nProduct Specifications
Model
LCD component
Max. resolution
Max. colors
Pixel pitch
Viewing angle
Screen active area
Computer input signal
Sync signal
PN-L702B
70" Class [69-1/2 inch (176.6cm) diagonal] TFT LCD
(pixels) 1920 x 1080
Approx. 1.06 billion colors
0.802 mm (H) × 0.802 mm (V)
160° right/left/up/down (contrast ratio ≥ 10)
inch (mm) 60-9/16 x 34-1/16 (1538.9 x 865.6)
Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 Ω]
Horizontal/vertical separate (TTL: positive/negative), Sync-on-green,
Composite sync (TTL: positive/negative)
Video color system
NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM
Plug and play
VESA DDC2B
Power management
VESA DPMS, DVI DMPM
Input terminals
Digital
PC/AV
HDMI x 1
Analog
Mini D-sub 15 pin, 3 rows x 1
PC
Audio
3.5 mm mini stereo jack x 1
Serial (RS-232C)
D-sub 9 pin x 1
Digital
DVI-D 24 pin (HDCP compatible) x 1
When PN-ZB01 PC/AV
(optional) is
Analog
BNC *1*2 x 1
PC
attached
Composite video BNC x 1
AV
S-video
x1
Component
BNC (Y, Cb/Pb, Cr/Pr) *1 x 1
Audio
RCA pin (L/R) x 2
Output terminals
Audio
RCA pin (L/R) x 1
Serial (RS-232C)
D-sub 9 pin x 1
Digital
DVI-D 24 pin x 1
When PN-ZB01 PC/AV
(optional) is
External speaker
7 W + 7 W [6 Ω]
attached
LAN terminal
10 BASE-T/100 BASE-TX
[When PN-ZB01 (optional) is attached]
Speaker output
7W+7W
Touch Panel
Detection method
Infrared blocking detection method
Detection area
inch (mm) 60-9/16 x 34-1/16 (1538.9 x 865.6)
PC connector
USB (1.1 compliant)
Power supply
Supplied from USB
Touch pen
Ultrasonic communication method
Power requirement
AC 100 V - 240 V, 2.8 A, 50/60 Hz
41°F to 95°F (5°C to 35°C)
Operating temperature *3*4
20% to 80% (no condensation)
Operating humidity*4
235 W / 1.0 W / 1.0 W
Power consumption
(Maximum / input signal waiting mode *5 / standby
mode *6)
Power consumption
240 W
[When PN-ZB01 (optional) is attached]
Dimensions (excluding protrusions)
inch (mm) Approx. 64-7/8 (W) x 4-9/16 (D) x 38-11/16 (H) (1,648 x 116 x 982)
Weight lbs. (kg) Approx. 154.3 (70)
Weight [PN-ZB01 (optional)]
lbs. (kg) Approx. 1.102 (0.5)
*1
*2
*3
*4
*5
*6
Cannot be used simultaneously.
Does not support plug and play.
Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP.
In such cases, please check the temperature condition specified by the optional equipments.
In addition, check the requirements of the computer and other devices to be connected, and make sure that all requirements are satisfied.
When AUTO INPUT CHANGE is set to OFF.
When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
53
E
Specifications
nDimensional Drawings
Note that the values shown are approximate values.
59-9/16 [1513]
Unit: inch [mm]
VESA holes *
7-7/8
7-7/8
[200]
[200]
3-15/16 3-15/16
[100] [100]
4-9/16
[116]
3-5/8 2-3/16
[92.5]
[56]
64-7/8 [1648]
1-7/8 [47]
7-7/8 [200]
41 [1041]
39-7/8 [1013]
38-11/16 [982]
Opening height (35-1/2 [901])
Opening width (61-11/16 [1567])
When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method.
SHARP recommends using M6 screws and tighten the screws.
Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in
serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch
(8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times
or more the weight of the monitor.
nPower management
This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in
order for the monitor’s power management function to work.
DPMS: Display Power Management Signaling
DPMS
ON STATE
STANDBY
SUSPEND
OFF STATE
Power
Screen consumption
Display
No
display
235 W*1
1 2
1.0 W* *
DMPM: Digital Monitor Power Management
Hsync
Vsync
DMPM
Screen
Power
consumption
Yes
Yes
Monitor ON
Display
235 W*1
No
Yes
Active OFF
No display
1.0 W*1*2
Yes
No
No
No
*1 When PN-ZB01 (optional) is not connected.
*2 When AUTO INPUT CHANGE is set to OFF.
nDDC (plug and play)
The monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters
is exchanged between the two. This function can be used if the computer supports DDC and it has been configured to detect
plug-and-play monitors.
There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.
E
54
Specifications
nCompatible signal timing (PC)
Screen resolution
640 × 480
VESA
800 × 600
848 × 480
1024 × 768
1152 × 864
1280 × 768
1280 × 800
1280 × 960
1280 × 1024
1360 × 768
1400 × 1050
1440 × 900
1600 × 1200*1
1680 × 1050
1920 × 1200*1
1280 × 720
1920 × 1080
Wide
720 × 400
1024 × 768
US TEXT
Sun
1152 × 900
1280 × 1024
1600 × 1000
Hsync
Vsync
Dot frequency
31.5kHz
37.9kHz
37.5kHz
35.1kHz
37.9kHz
48.1kHz
46.9kHz
31.0kHz
48.4kHz
56.5kHz
60.0kHz
67.5kHz
47.8kHz
60.3kHz
49.7kHz
60.0kHz
64.0kHz
80.0kHz
47.7kHz
65.3kHz
55.9kHz
75.0kHz
65.3kHz
74.0kHz
44.7kHz
66.3kHz
67.5kHz
31.5kHz
48.3kHz
53.6kHz
56.6kHz
61.8kHz
71.8kHz
71.7kHz
81.1kHz
68.6kHz
60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
60Hz
70Hz
75Hz
75Hz
60Hz
75Hz
60Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
70Hz
60Hz
66Hz
70Hz
66Hz
76.2Hz
67.2Hz
76Hz
66Hz
25.175MHz
31.5MHz
31.5MHz
36.0MHz
40.0MHz
50.0MHz
49.5MHz
33.75MHz
65.0MHz
75.0MHz
78.75MHz
108.0MHz
79.5MHz
102.25MHz
83.5MHz
108.0MHz
108.0MHz
135.0MHz
85.5MHz
121.75MHz
106.5MHz
162.0MHz
146.25MHz
154.0MHz
74.4MHz
148.5MHz
148.5MHz
28.3MHz
64.13MHz
70.4MHz
74.25MHz
94.88MHz
108.23MHz
117.01MHz
134.99MHz
135.76MHz
Digital
DVI*2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
HDMI
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
Analog
(D-SUB/RGB*2)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1 Displays a reduced image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed.
*2 Available when the PN-ZB01 (optional) is attached.
* All are compliant only with non-interlaced.
* Depending on the connected PC, images may not be displayed properly even if the compatible signal described above is input.
* The frequency values for the Sun are reference values.
nCompatible signal timing (AV)
Screen resolution
1920 × 1080p
1920 × 1080i
1280 × 720p
720 × 576p
720 × 480p
640 × 480p(VGA)
720(1440) × 576i
720(1440) × 480i
Frequency
DVI-D*
HDMI
Component
24Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
* Available when the PN-ZB01 (optional) is attached.
55
E
Specifications
nPC/AV DVI-D
(DVI-D 24 pin)
No.
1
input terminal pins
Function
No.
Function
No.
Function
13
N.C.
1
TMDS data 2+
11
TMDS clock shield
2
TMDS data 2+
14
+5V
2
TMDS data 2 shield
12
TMDS clock-
3
TMDS data 2/4 shield
15
GND
3
TMDS data 2-
13
CEC
4
N.C.
16
Hot-plug detection
4
TMDS data 1+
14
N.C.
5
N.C.
17
TMDS data 0-
5
TMDS data 1 shield
15
SCL
6
DDC clock
18
TMDS data 0+
6
TMDS data 1-
16
SDA
7
DDC data
19
TMDS data 0/5 shield
7
TMDS data 0+
17
DDC/CEC GND
8
N.C.
20
N.C.
8
TMDS data 0 shield
18
+5V
9
TMDS data 1-
21
N.C.
9
TMDS data 0-
19
Hot-plug detection
10
TMDS data 1+
22
TMDS clock shield
10
TMDS clock+
11
TMDS data 1/3 shield
23
TMDS clock+
12
N.C.
24
TMDS clock-
No.
terminal pins
Function
No.
nRS-232C input
(D-sub 9 pin)
Function
No.
terminal pins
Function
No.
Function
+5V
1
N.C.
6
N.C.
10
GND
2
Transmitted data
7
N.C.
11
N.C.
3
Received data
8
N.C.
N.C.
12
DDC data
4
N.C.
9
N.C.
5
GND
13
Hsync signal input
5
GND
6
GND for red video signal
14
Vsync signal input
1
Red video signal input
9
2
Green video signal input
3
Blue video signal input
4
7
GND for green video signal 15
8
GND for blue video signal
nPC/AV DVI-D
(DVI-D 24 pin)
No.
1
56
Function
terminal pins
TMDS data 2-
nPC D-sub input
(Mini D-sub 15 pin)
E
No.
nPC/AV HDMI input
(HDMITM Connector)
DDC clock
output terminal pins
Function
No.
Function
nRS-232C output
(D-sub 9 pin)
No.
Function
terminal pins
No.
Function
TMDS data 2-
13
N.C.
1
N.C.
6
N.C.
2
TMDS data 2+
14
+5V
2
Received data
7
N.C.
3
TMDS data 2/4 shield
15
GND
3
Transmitted data
8
N.C.
4
N.C.
16
Hot-plug detection
4
N.C.
9
N.C.
5
N.C.
17
TMDS data 0-
5
GND
6
DDC clock
18
TMDS data 0+
TMDS data 0/5 shield
7
DDC data
19
8
N.C.
20
N.C.
9
TMDS data 1-
21
N.C.
10
TMDS data 1+
22
TMDS clock shield
11
TMDS data 1/3 shield
23
TMDS clock+
12
N.C.
24
TMDS clock-
Mounting Precautions
(For SHARP dealers and service engineers)
• When installing, removing or moving the monitor, ensure that this is carried out by at least 4 people.
• Be sure to use a wall-mount bracket designed or designated for mounting the monitor.
• This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials
such as plaster / thin plastic board / wood before starting installation.
This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor.
Install by the most suitable method for the material and the structure.
• To attach a VESA-compliant mounting bracket, use M6 screws that are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the
thickness of the mounting bracket.
• After mounting, please carefully ensure the monitor is secure, and not able to come loose from the wall or mount.
• Do not use any screw holes other than VESA holes for installation.
nAttaching the Tray
1. Remove the cover from the back of the monitor.
2. Secure the tray mounting fitting.
Secure using the screw removed in step 1 and 2 M5 tray
mounting screws (supplied).
(2)
Cover (supplied)
(3)
M5 tray mounting screws
(supplied)
(1)
Tray mounting
fitting
Bracket (supplied)
Screw removed in step 1
3. Secure the tray.
Insert the tray into the tray mounting fitting and secure with
2 M4 tray mounting screws (supplied).
Tray
(supplied)
M4 tray mounting screws
(supplied)
57
E
PN-L702B Mu EN11H(1)