TOYOTA CAMRY LE / SE / XLE 2012

TOYOTA CAMRY LE / SE / XLE
2012-
DUAL SEAT HEATER KIT
Section I – Pre-Installation Check
Kit Part Number: 00015-91248-05
General Applicability
Camry LE / SE / XLE
3
4
Recommended Sequence of Application
1
5
Item #
1
2
3
Accessory
Wiring
Elements
Vehicle Service Parts (may be required for reassembly)
2
Kit Contents
Item #
1
2
3
4
5
6
Quantity Reqd.
2
2
1
1
2
1
Description
Cushion Element
Back Element
Driver Main Harness (red)
Passenger Main Harness (blue)
Control Switch
Hardware Bag
Hardware Bag Contents
Item #
1
2
3
4
5
Quantity Reqd.
15
Description
Wire Ties
Additional Items Required For Installation
Item #
Quantity Reqd.
1
As needed
Description
Switch Cutout Template
Vehicle Protection Blankets
Item #
1
2
3
4
5
6
Part #
00012-91248-41
00012-91248-42
00012-91248-43
00012-91248-44
00012-91248-45
00012-91248-46
Description
Cushion Element
Back Element
Driver Main Harness
Passenger Main Harness
Control Switch
Relay, SPDT
Legend
STOP
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury
CRITICAL PROCESS: Proceed with caution to ensure
a quality installation.
GENERAL PROCESS: This highlights specific
processes to ensure a quality installation.
TOOLS & EQUIPMENT: This calls out the specific
tools and equipment required for this process
VEHICLE PROTECTION: This calls out for protection
of vehicle required for this process
Conflicts
Note: Factory leather and cloth
Recommended Tools
Safety Tools
Use During Installation
Gloves
Safety Glasses
Special Tools
Battery Post Protector
Installation Tools
Connector De-pinning Tools
Side cutter
Knockout Punch or Bit
Pilot Drill Bit
Torque Wrench
Camry Switch Fixture
Cordless Drill
For OEM connector
To cut wire ties
13/16” Step Bit
Round, 3/8” Drill
48 inch/pounds
Special Chemicals
Form #5356, Rev. A, 09-19-12
Page 1 of 7
TOYOTA CAMRY LE / SE / XLE
2012-
DUAL SEAT HEATER KIT
Section II –Installation
Pre-Installation Suggestions
1. Disconnect the negative battery cable and wait
for 3 minutes before beginning installation, to
avoid unintended air bag deployment. Note
and record any anti-theft radio codes prior to
disconnecting. Figure 1
Figure 1
2. If vehicle is in Electronics work area,
proceed to step 1 page 4. If vehicle is in
Leather shop, proceed to next section
“Install Heating Elements”.
Install Heating Elements
1. Remove seats from vehicle per vehicle’s
service manual and place on a clean work
surface.
2. Remove seat covers per vehicle’s service
manual.
3. Caution: The heating elements must be
installed wrinkle-free.
4. Obtain the back heating element. Remove the
protective layer from the element’s double
sided tape and place it onto the seat back foam
roughly centered on the foam from side to side
with the top of the element just below the
transverse listing (tie bar trench). Figure 2
5. Route the element wiring harness down to the
bottom of the seat back, inboard of the hinge
cover and under the seat.
Figure 2
Align
channels
with
cutouts
Figure 3
Route
harnesses
here
6. Repeat the process above for the seat cushion,
laying the heating element transversely such
that it does not interfere with the horizontal
listings. Figure 3
7. Secure the seat harnesses to the tie down bar
and run down the side listing to the back of
the seat, then down. Re-attach seat covers.
Figures 4-5
8. Replace the driver and passenger seats into the
vehicle. Connect the seat element connectors
to the main harnesses. Secure the harness
with wire ties and allow adequate slack to
prevent damage during seat adjustment.
Figure 6
Form #5356, Rev. A, 09-19-12
Figure 4
Twist
harnesses
together
and route
here
Figure 5
Page 2 of 7
TOYOTA CAMRY LE / SE / XLE
2012-
DUAL SEAT HEATER KIT
Section II –Installation
Install Heating Elements (cont’d)
9. Make sure vehicle floor-pan is clear and
carefully re-locate seat into vehicle.
10. Ensure all connectors under seat have been
properly connected and secured with wire ties,
and that nothing will be damaged upon seat
movement.
11. Install seat bolts and torque per service
manual.
Figure 6
12. Reconnect battery cable(s). Torque 10mm bolt
to 48 inch-pounds. Re-enter any theft
deterrent information, if applicable.
13. Note: If the passenger seat cushion has a Seat
Occupant Sensor for Airbag Deployment, it
must be re-calibrated per guidelines in the
Factory Repair Manual.
14. Place the Seat Heater Operation Instructions
in the glove box.
Form #5356, Rev. A, 09-19-12
Page 3 of 7
TOYOTA CAMRY LE / SE / XLE
2012-
DUAL SEAT HEATER KIT
Section II –Installation
Install Main Harnesses
Camry LE / SE
Figure 7
1. Remove the shift knob bezel / cup holders,
and center floor console.
2. Install the driver (red tape) and passenger
(blue tape) main power harnesses near the
factory floor harness as shown. Figure 7
NOTE: For XLE models, take care to route
the relays and main harnesses beneath the
HVAC ducting at the right of the shifter
bl
3. Route the outputs for the driver (red) and
passenger (blue) side seat elements to the
opening in the carpet underneath the seat near
the air vent. Figure 8
4. Route the inputs for the driver (red) and
passenger (blue) side switches to the area in
front of the shift knob and set aside. Figure 9
5. Route and connect the two ground terminal
rings to ground point I3 below the HVAC
controls. Figure 10
Figure 8
6. Remove left door step, kick panel, and lower
instrument panel.
7. Route the inputs for the driver and passenger
power (red and blue wires) to the center
console beneath the radio, and left behind the
driver knee panel to the driver side junction
box. Figure 11
8. Disconnect connector 3C from the junction
box, and release the locking tabs on the
connector. Insert the red wire (driver side
power) into Pin 4 of connector 3C. Insert the
blue wire (passenger side power) into Pin 13
of connector 3C. Replace the locking tabs on
the connector and reconnect the connector to
the Junction Box. Figure 12a
Figure 9
Ground
I3
Wire
Ties
Figure 10
Form #5356, Rev. A, 09-19-12
Wire
Ties
Figure 11
Page 4 of 7
TOYOTA CAMRY LE / SE / XLE
2012-
DUAL SEAT HEATER KIT
Section II –Installation
Figure 12a
Red
Wire
Pin 4
Blue
wire
Pin 13
9. NOTE: XLE models with SmartKey may be
pre-wired for the factory seat heater (Figure
12b). In this case remove the RED and
VIOLET wires from Pin 4 and Pin 13
respectively, and tape them to the harness as
shown in Figure 12c.
Figure 13
Camry LE / SE
Figure 12b
Relays
Wire
Ties
Figure 12c
10. Secure the harnesses with wire ties to the
factory harness in center console and behind
the driver knee panel. Figures 11, 13 (Camry
LE / SE shown)
Form #5356, Rev. A, 09-19-12
Wire
Ties
Page 5 of 7
TOYOTA CAMRY LE / SE / XLE
2012-
DUAL SEAT HEATER KIT
Section II –Installation
Install Switches
Camry LE / SE
Figure 14a
Camry XLE
Figure 14b
1. Use the Camry drill fixture to make 3/8” pilot
holes in trim piece. Enlarge hole with a
13/16” (21mm) hole saw. Figures 14a-15
NOTE: Camry LE / SE share one fixture, Camry
XLE is a separate fixture.
2. Push the switch harness through hole and snap
the switch firmly into place. Figure 16
3. Connect the switches to the switch inputs on
the main harnesses in the center console.
Connect left (driver) switch to the 4-pin
connector marked with the red tape, and
connect the right (passenger) switch to the 4pin connector marked with the blue tape.
4. Use the Seat Heater Harness Tester to validate
switch and harness function and orientation.
5. Reinstall all trim panels in the reverse order of
removal.
6. Reconnect battery cable(s). Torque 10mm bolt
to 48 inch-pounds. Re-enter any theft
deterrent information, if applicable.
Drill (2) 13/16”
Holes
Figure 15
Figure 16
Form #5356, Rev. A, 09-19-12
Page 6 of 7
TOYOTA CAMRY LE / SE / XLE
2012-
SEAT HEATER KIT
Section III – Functional Verifications
Check
Look For
Verify Function and Heat: IGN ON, Check switch
Switch in ‘High’ setting. The LED will turn red.
in both ‘High’ and ‘Low’ position.
The heat will be noticeable within 3 minutes. The
heating time can vary according to the type of seat
cover material and kind of clothing/coat that is being
worn. The heating must be switch to the ‘Low’
setting in order to avoid overheating, when the
desired temperature has been reached.
Switch in ‘Low’ setting. The LED will turn green.
The heating time can vary according to the type of
seat cover material and kind of clothing/coat that is
being worn.
Troubleshooting
The heating does not function although it is switched Check the fuse and change if necessary.
on. The LED is not illuminated.
The LED in not illuminated although the heating is
The LED in the switch is defective.
functioning and switched on.
The heating does not function although it is switched The temperature of the seat cover could be too high
on. The LED is on.
due to high interior temperature. The thermostat in
the seat heating unit is connected. Wait until the seat
cover’s temperature has fallen and try again.
The fuse burns out repeatedly.
Form #5356, Rev. A, 09-19-12
Verify the fuse rating is correct: 10 amps.
Page 7 of 7
Open as PDF
Similar pages