Model:G2201
User Manual
Please read this manual before using and
save this manual for future reference
NOTES ON INSTALLATION
The unit is designed for 12V DC ,
negative ground operation system
only.
Before installing the unit, make sure
the vehicle is connected to DC 12V
negative ground electrical system.
The negative battery terminal must
be disconnected before making
connections, which can reduce
damage to the unit due to short
circuit.
Be sure to connect the color coded
leads correctly according to the
diagram. Incorrect connection may
cause the unit to malfunction or
damage the vehicle electrical
system.
Be sure to connect the speaker(-)
Leads to the speak(-) terminal.
Never connect the left and right
channel speak cables together or to
the vehicle body.
Do not block vents or radiator panels
Blocking them will cause heat to build
Up inside the unit and may damage it.
After the completion of the
installation and before to play
(including replacing the battery),
please press the RESET button on
the front panel with pointed objects
(Such as ball-point pen)to set the
unit to initial status.
SPECIFICATION
CONTENTS
General
Power Requirement
Load Impedance
Max Power Output
Tone Control
Dimension
Mounting Dimension
Weight
14.4DC
4ohm
60W 4
+/-8DdB(Bass100Hz,Treble 10KHz)
Approx,192 188 105mm(D W H)
Approx,169 178 100mm(D W H)
Approx.2.15kg
DVD Deck Section
Disc Played
Video System
DVD/VCD/2.0/MP3/MP4(DIVX/CD/Picture-CD)
PAL/AUTO/NTSC
Video Section
Video System
Video Output level
Horizontal Resolution
4:3Letter Box and 4:3Pan Scan,16:9wide-screen
1.0vp-p 75ohm
500
Audio Section
Maximum Output level
Frequency Response
Signal-to-noise Ratio
Separation
2Vrms(+/-3dB)
20 to 20KHz
85dB
80dB
AM Tuner Section
Frequency Range
IF Range
Usable Sensitivity(-20dB)
522-1620(Europe/China/Russia)
530-1710(U.S.A);522-1629(Japan)
450KHz
25dB
FM Tuner Section
Tuning Range
IF Range
Usable Sensitivity
Signal-to-noise Ratio
Stereo Separation
Frequency Response
87.5-108(Europe/China);87.5-107.9(U.S.A)
76-90(Japan);65-108(Russia)
10.7MHz
15dB
60dB
30dB(1KHz)
30-15KHz
Precautions
2
Panel illustration
3
Main menu
5
Media player
6
Bluetooth
7
AV IN
8
Setup
9
iPod player
10
GPS operation
11
Radio operation
20
TV operation
21
Location of the Remote Control
22
Remote Control Operation
23
Installation
32
Simple Troubleshooting Guide
34
Wiring Diagram
35
Specification
36
03.MAL.6950.001.19
Note: Due to continuous product improvement, specifications and design are
Subject to change, without notice.
36
1
PRECAUTIONS
WIRING
This unit can play the following disc only:
Type of disc
Label on the disc
Recorded material
DIAGRAM
STANDARD CONNECT
Size of disc
Sound and moving
pictures
Sound and moving
pictures
Sound and moving
pictures
Sound and moving
pictures
GPS interface
Sound only
Do not attempt to modify the unit.
Unauthorised modification may
damage the unit.
----Do not use CD with paste residue
or ink on the surface
Stop the vehicle before carrying
out any operation that could
Interfere with your driving.
Do not operate the unit in exteme
temperatare inside the vehicle.
The operating temperature of the
unit is between-20 to+60
To enjoy optimum sound and
images while playing, handle the
disc as follows:
----Handle the disc by its edge to keep
the disc clean. Do not touch the surface.
----Do not use CD with labels or
Stickers attached. It cause failure
Of the loader mechanism.
(Shown in picture)
1
----Clean the disc with cleaning cloth
Wipe each disc from the centre out
(Show in picture
Antenna Receptacle
2 Output Socket(female)
3
Fuse Holder(15A)
4 Video Out Receptacle
5
Output Socket(male)
6 iPod in(optional)
2
7
Mincrophone input
8
USB
35
SIMPLE TROUBLESHOO TING GUIDE
Problem
Panel illustration
Cause/solution
No power
Check the fuse. Replace with the proper
value if necessary
Some errors occur in the LCD or no
function when pressing the button
Press the RESET button
Unable to receive stations
Check and make sure the antenna is
properly connected.
Antenna may not have proper length. Make
sure the antenna is fully exten ded. If broken
replace the antenna with a new one.
The broadcasting signal is too weak.
The antenna is poorly grounded. Check and
make sure the antenna is properly grounded
at its mounting location.
Poor effect on receiving
A CD is loaded in the mechanism.
CD s cannot bo loaded
Tune in the frequency accurately
The stereo indicator"
"is flashing
No picture
Picture distortion
Wrong region code
The broadcasting signal is too weak.
(Set to the MONO mode)
The video line from main unit to the TV is
not connected properly .
Improper setting of the color system. Set the
color system to PAL or NTSC, according
to the connected television.
The CD is dirty or damaged.
Under DVD mode ,press"
" on
remote control pad twice, the press
arrow
on remote control pad,
and press pad 0-6according to your region
Tel button
Angle button
Volume button
Remote control sensor
Mode button
Eject button
Reset button
Power button
Touch screen
GPS button
For example, if disc region is 1, press
arrow
and 1 on the remote control.
No memory on radio sation
Press the station for 3 seconds to
memorize preset station.
For example, if a user wants to
Preset radio frequency FM 88.10
On station 1, just simply press
station 1 for 3 seconds when
frequency is tuned at FM 88.10
1 Tel button
When there comes a call, press it to
Answer the call.(When you want to
Reject or hang up the call, press" "
on the front panel or HANG UP touch
key in the TEL touch menu).
2
Volume button
For volume button, press(
) the
button clack wise to increase the
sound level and anti-clockwise to
Decrease the sound level.
Note:If any of the problem persist, consult your nearest service dealer.
Never attempt to disassemble the unit by yourself.
34
3
Panel illustration
Mode button
Press it to select source in the
following order:
Reset butto n
Operating the unit for the first time or
after replacing the car battery , you
must reset the unit. Press this button
with a pointed object (such as a
ballpoint pen) to set the unit to initial
status.
Note: When errors occur on the LCD
display ,you can also press RESET
button to clear the error, It will erase
the clock setting and some
memorized functions.
Eject bu tton
Angle button
Press it to adjust the angle of the front
panel, and there are totally four
angles optional.
Remote control sensor
Sensor for the card remote commander.
(For remote control version only)
Note: This window is used with remote
control function. Without this
function,you should ignore the
operation contents about remote
control function.
4
Mounting Example
A. When there is no disc in the unit,
press it and the front panel will
flip down to shown the disc slit in
the main unit, Insert the disc into
the CD slot, and the mechanism
wills automatically playback the
Disc.
B. When there is a disc in the unit,
press it, the front panel will
automatically flip down and eject
the disc, if you don t take the
disc away within 5 seconds, the
mechanism will automatically slot
in the disc, lock the front panel and
select radio mode.
Power button
Touch scree n
Press any place on the touch screen,
the corresponding touch menu will
display on the screen under different
Mode, pleas refer to corresponding
Chapter below for operation in
details.
INSTALLATION
This mounting method is used for Japanese cars.
The actual mounting method should depend on
the types of the cars.
Notes: 1.Store small articles that are not accessible
to children.
2.Install only with the supplied screws.
3.Installation varies depending on the
type of cars and unit installed by
qualified technician.
Bracket
Existing parts supplied
with your car
Installing the front panel
A. Under sleeping mode, press it to
turn the unit on, and the unit will
automatically select radio mode.
B. Under working mode, press and hold
the button for more than 3 seconds to
return the unit off.
GPS button
Detaching the front panel
Press it to unter the GPS menu, press
it again to return to the initial status.
Be sure to press before
detaching the front panel. To
detach panel, press the latch
shown n the left.
Precautions
Do not touch the front panel connection
on the unit body, since this may result in poor
electrical contact. If dirt or dust get on the
contacts, wipe them with c clean ,dry cloth.
33
INSTALLATION
Main menu
Parts List(The numbers in the list are keyed to those in the instructions.)
Fasten the rear bracket screws and
back side harness, and fix the unit
Well.
To remove the set,
pull the set out
from the dash board.
32
Media player
iPod player
Bluetooth
GPS
AV in
Radio
USB
Back sight
Setup
TV
2,6,7,8,10 function is optional
5
Media player
REMOTE CONTROL OPERATION
E. DIGITAL SETUP
Media player
TITLE KEY
3.VOL/SEL key
This key has SEL function,
Repeatedly press it to select mode
In the following order:
Press it to select track downward.
Press and hold it for more than 3
Seconds to fast reverse the track.
This is for the user to set operation
mode, dynamic range compression
And stereo mode.
a. OP Mode
--In DVD VCD playing mode,
Press 24 (TITLE) key to show all
Track title on TV screen. Press
4
key to choose your
Desired track number and press
(ENTER) key or 2 (
) key 6
start.
Note: 1.No title display in Mp3 CD
2.To choose a desired language,
Press title key.
5.Parameter display
After selecting the desired mode.
you can adjust its level by pressing
Area 5 , and the corresponding
Parameter will display in this area.
ZOOM KEY
To set the operating modes for Dolby
Digital decoder .
--In DVD VCD playing mode,
press 25 (ZOOM) key once for
1.5x Mode, twice for 2 x Mode.
Third time for 3 x Mode, forth
time for 1/2 mode, fifth time for
1/3 mode, sixth time for 1/4 mode.
b. Dynamic Range
Press it to select track upward, Press
and hold it for more than 3 seconds
to fast forward the track.
.
Note: No ZOOM function CD/MP3 playing
Mode.
7.MORE:
1.PLAY/PAUSE key
Press it to pause the playback, and
press it again to resume to normal
Playback.
2.MUTE key
Press it to cut off the sound output,
And
appears in the LCD;
Press it again to cancel the MUTE
function.
6
Press it to display more menu.
8.MODE key
To set dynamic range compression
c. Dual Mono
Press the button to return to main menu.
9.TA key(optional)
Traffic program/Traffic Announcement.
TA function on/off.
To set the stereo mode.
31
Bluetooth function(optional)
REMOTE CONTROL OPERATION
SPDIF/PCM:
When the player is connected with the
2 channels, digital stereo amplifier,
please select this item when the
playing disc is recorded in Dolby
digital or MPEG. The analog or optical
output will be modulated to 2 channels
output by PCM.
Note: This function is in invalid for this
model.
b. Contrast
10.RPT key
11. RDM key
b. Key
c. Hue
Press it to play the disc in random,
Press is again to resume normal
Playback.
12. OSD
OSD information display.
This is to select Treble or Bass
according to your needs.
D. VIDEO SETUP
Bluetooth
Repeat function. Press it to repeat the
current track/chapter; Press it
Again to repeat the title; Press it
The third time to repeat all; Press it
The fourth time to cancel the repeat
function.
13. L/R key
d. Satura tion
Press it to get switch R+R/L+L
/STEREO.
14. N/P key
Press it to switch video system:
Bluetooth pairing setting:
a)Bluetooth active is the default
setting for the player.
b)To pair the player with mobile,
operate mobile: Activate Bluetooth
and star a device search. Select the
Bluetooth device in the player and
Press Pair .
C)Operate mobile and input the
default password 0000 .
15. MENU
This is for the user to set
Brightness,
Contrast, Hue and Saturation of the
picture by pressing the arrow left/
right button.
e. Sharpness
Press it to switch to menu, and dvd
Will enter title menu and display all
Titles for dvd disc and you can
Choose your desired you can
Track by pressing direction button.
D)After the pairing is successfully
Connected, SUCCESS will
display on the LCD and you can
make call through the player.
Make call through the player:
a. Brightness
16. Direction keys
Press direction keys(
)
To select your desired title or track.
Press (ENTER key) to confirm the
change.
NOTE: Only on TV/AV mode ,the
Video setup is available.
30
17. OK
Press it to confirm.
1.Number keys:
Input the phone number you want
to call.
2.Cut off:
When you input the incorrect
character, press it to delete the
Incorrect character.
7
REMOTE CONTROL OPERATION
AV IN
3.Connect:
To pair mobile with the player.
Bluetooth can be switched
On or Off by press ing this button
After The pairing is connected.
3. In AV IN mode, all the touch
keys keep the same functions and
operate in the same way as other
modes. For details of this operation,
please see main section in Media
player chapter.
4.
After you input the phone number,
press it to make a call. When there
is an incoming call, press it to
answer the call.(The button in
the front panel has the same function
and operated as the same way.
Note: The unit can t be directly
Connected with high power AUX source, in
order to aviod fire or other damage to the
unit.
4.Press SYS key to switch the video
system:
5.
When there is an incoming call,
press it to reject or to end the call.
Exit the touch menu.
7.Status bar
Display status of the connection
or phone number.
AV IN
g. Default
B. LANGUAGE SETUP
1.Press MODE key to switch to
AV IN mode.
2.Connect to AV IN source.
8
d. MENU Language
Select the preferred OSD Language,
Audio Language, Subtitle language
and Menu Language by using the.
ARROW keys.
USB Player
The unit can be connected to a USB
device for playing MP3/MP4/JPG files
through the USB cable.
All the touch keys keep the same
functions and operate in the same
way as other modes, For details of
this operation, please see main
section in Media player chapter.
C. AUDIO SETUP
a. OSD Language
SPDIF/OOF:
Analog or optical output port has
no output signal at all.
a. AUDIO Out
b. AUDIO Language
AV IN OPERATION
c. SUB TITLE Language
This is to activate the audio output
from SPDIF/OFF mode to SPDIF/
RAW mode or SPDIE/PCM mode.
SPDIF/RAW:
When the player is connected with
the power amplifier by the analog
or optical port, please select this
Item when the playing disc is recorded
In Dolby Digital, DTS or MPEG. The
power amplifier you connected must
have decode function for Dobly Digital,
DTS or MPEG.
29
Setup
REMOTE CONTROL OPERATION
a. TV Type
f. Rating
Setup
(4)CLK
Clock display on/off, the current
Time display on LCD when CLK ON.
(5)BEEP
Keypad tones setting on/off.
1. 4:3 PS
Played bask in the PAN& SCAN
style.(If connected to wide-screen
TV, the left and right edgesare cut
off)
2. 4:3 LB
Played back in LETTERBOX style.
(If connected to wide-screen TV ,
black bands appear at top and
bottom of the screen)
3.16:9
Select when a wide-screen TV set
Is connected.
e. Password
1. Basic setup
Select suitable guidance rating by
the cursor button and confirmed by
Pressing 6 ENTER key)
Rating 1:[KID SAFE]
Select this when the program are safe
for all kids to view.
Rating 2:[G]
Select this that allows admission to all
Ages.
Rating 3:[PG]
Select this that needs parental guiding.
(1) RADIO
Select radio frequency according to
The following sequence:
Rating 5 :[PG-R]
Select this when PG-R was printed
On the DVD disc.
Rating 6:[R]
Select this when children under 17 must
be guided by their parents.
28
Rating 7:[nc-17]
Select this when children under 17 are
forbidden to view.
(1)
Brightness adjustment
(2)
Color Adjustment
Rating 4:[PG13]
Select this when children under 13 are
forbidden to view.
Enter the password and press ENTER
button. Type the old password (The
initial factory code is 0000) and key
in 4 characters password now you
want to use, and type again to confirm.
2.Video setup
(2) TV system switch:
Press it to switch the tv video system:
Note :the player will memorize
the Tv system setting when the
player is off.
(3)
Contrast adjustment
(4)Video mode
Press it to switch video mode
According to the following sequence:
(3)TIME
Time adjustment
Rating 8:[ADULT]
Select this only allows admission to all
Adults.
9
ipod player(optional)
3.Audio setup
ipod player
REMOTE CONTROL OPERATION
SETUPKEY
1.Press 23 ( SETUP KEY) of remote
Control in the stop mode. (Press the
20 STOP key twice to ensure the
Player is under STOP mode.)
2.The main page of setup menu is disPlayed.
(1)BAS
BASS adjustment
(2)TRE
Treble adjustment
1. +
Volume adjustment.
+:volume level increase
-:volume level decrease
4.Direction keys
Press direction keys to select your
desired menu or location.
5.UP DOWN
Press them to select
your desired title or track.
3.Select the preferred item by using
the 4 (ARROW keys).
4.Press 6 (ENTER key.
A .System Setup
This setup page includes all items of
TV system, Screen saver , TV type,
passward ,Rating & Default features.
For detail please refer to SYSTEM
SETUP MENU.
B. Language setup
This setup page includes all items of
OSD language features. For details
Please refer to LANGUAGE SETUP
MENU.
C. Audio Setup
This setup page includes all items
for AUDIO. Please refer to AUDIO
SETUP MENU.
D. SYSTEM SETUP
This setup page includes all items
for VIDEO. Please refer to VIDEO
SETUP MENU.
5.Back
Exit setup menu.
Play/Pause.
A. SYSTEM SETUP
A. TV System.
(3)BAL
Balance adjustment
(4)FAD
Fade adjustment
(5)LOUD
Loudness
(6)EQ
Press it t select the desired EQ
effect in the following order:
2.MENU
Press menu to control the
functions of the iPod.
3.OK
Press it to confirm.
Press it to select track downward/
upward. Press and hold it for more
than 3 seconds to fast reverse/fast
forward the track.
This player can play disc recorded
In either PAL or NTSC format. Select
NTSC format when you connect
To NTSC TV. Select PAL format when
You connect to PAL TV. Select the
Format (PAL/NTSC) according to
you TV system.
b. Auto Play
Select the SCREEN SAVER
Output ON/OFF .
C.Video
7.Back
Return to main menu
Note : This function is invalid for this model
10
27
GPS Operation
REMOTE CONTROL OPERATION
GPS Operation
Setting CD Playback Time
--In VCD CD mode, press 18
(GOTO) key and set the time when
you begin to play the track, and
the television will display the
time --:--. Enter your desired time
by pressing number button 14
(0~10+).For example, enter:
25:00, and press 6 (ENTER) to
confirm. It will automatically start
playing the track from the point of
twenty-fifth minutes in the disc.
--In DVD playing mode, press 18
(GOTO) key once and input a
desired track number, Then press
6 (ENTER) key to play the DVD
from the position corresponding to
the track number selected.
--In DVD playback mode, press 18
(GOTO) key once and input a
Desired time to play the DVD from
the position corresponding to the
time selected. For example, press
18 (GOTO) key once and the
television will display the time--:--:-Enter your desired time by pressing
number button 14 (0~10+). And 4
direction button, Then press 6
(ENTER) button, it will automatically
start playing the track trom the point
of your desired time in the disc.
Note: No time play function for Mp3
.
Mode Switch
--Press 19 (MODE) button to
Switch to radio mode or playback
Mode.
Stop the Playback
--In DVD mode, press 20
button to suspend the playback
and press Play to continue.
Press it again to stop the playback.
MULTI-ANGLE KEY
--In DVD playing mode, press 21
(ANGLE key to watch the DVD
Content from different angle.
SLOW KEY
--In DVD/VCD playback mode, press
22 (SLOW) key once for / slow, twice
for 1/3 slow, thrice for 1/3 slow, and
so on. When the key is pressed the
seventh time, it will return to normal
Playback.
Note : Not applicable in Mp3 and CD
playback.
Safety Notices and Warnings
Global Positioning System(GPS is operates and controlled under the
sole responsibility of the Government of the United States of America,
who are responsible for its availability and accuracy. Any change in GPS
availability and accuracy, or in environmental conditions, may impact the
operation of your Navistar.
Use this product prudently. The product is to be used only as a
navigation aid. It is not for precise measurement of direction, distance,
location or topography.
When the artificial satellite carrying out GPS first fixes position, stay
in thesame place please, use more spacious that place is suitable , superjacent
have not to blocking anything. Need to look at environment that time and
artificial satellite signal intensity but fix above waiting for the ten
minutes.
For your own safety, do not operate the controls of the product while
driving.
GPS satellite signals can not pass through solid materials(except
glass).When you are inside in a tunnel or building, GPS positioning is not
available. Signal reception can be affected by situation such as bad
weather or dense overhead obstacles (e.g. trees and buildings)
The wireless devices might interfere the reception of satellite signal
and cause
the reception of the signal to be unstable.
When you get off the car, do not leave your device on the dashboard or
the car glass that is subject sunlight. The overheating of the battery can
cause malfunction and/or danger.
The windshield receives paste the paper which be used for adiabatic or
preventing explosion, will disturbed the signal quality. For better signal
reception, it is recommended that you can choose adiabatic paper of not
containing metal matter or use a car antenna(option).
The calculated route is for references only. It is user's responsibility to
follow the traffic signs and local regulations along the roads.
26
11
GPS Operation
REMOTE CONTROL OPERATION
Chapter 1.System Set Up
Press Config
interface.
Icon on the main menu and then enter into the system Set-up
--During CD MP3 VCD mode,
Press 15 (RPT) to repeat the
current track being played. Press
it again to cancel the repeating
function.
Note: In VCD MP3 CD mode. The
Initial setting is repeat playing
All the tracks.
Note :In radio mode, press 12
(AMS/RPT)to scan each stored
Station for 10 seconds.
The system menu provides the Volume , Backlight , NaviSetting
Calibrate , Language , GPSTest , and Return for choose, the
introduction are in the following chapters.
1.1.Volume
Examine or set up the system's volume.
1)Press the Config Icon on the main menu and then enter into the system
Set-up functions.
2)Press the volume Icon on the set up menu.
12
Random Playing
-- During playback mode, press 13
(RDM) button to play any track at
Random.
Number Buttons
-- During radio , you can select
one of the 6 stored stations
on each band by pressing
any one of the number
button 14 .
--During the playing mode,
you can select any track directly
by using 14 number button (0~10+).
for example, if you need the fifteenth
track, you can first press button 10+
and then press button 5, the
corresponding track (15) will be
Played.
Left/Right/Stereo Selector
--During playback mode,
continuously press 15 (AUDIO)
can change the sound to left/right
speaker or stereo mode.
Note: There are 5 different surrounding
Effect in surround mode. During
VCD mode, you can see the different
Pictures indicating different effects
On the television.
Playing PBC (menu)
--During VCD mode only, when
pressing 16 (PBC) button at
the first time, PBC playback starts
and the menu of entire disc appears
on the television. And then you can
select your favourite track by using
number button 14 (0~10). When a
track is playing ,you can press 20
(STOP/RETURN) button to return
to the menu if you want to stop to
select other tracks. To cancel PBC
playing, press 16 (PBC) button
again.
Subtitle Selector
--During DVD mode, press 17
(SUB-T) button to switch the menu
to Chinese or English.
Note: When button 10+ is first pressed, it works
as 10+ , it works as 20+ when pressed at
the second time, the third...30+....and so
on and so forth. In PBC playback mode,
number button is not functional.
25
GPS Operation
REMOTE CONTROL OPERATION
Volume Increasing/Decreasing
--Press 7 (VOL+or VOL-) button
to increase or decrease the volume
level respectively .
Tuning/Selecting Tracks
/Fast Rewind/Forward
--During radio mode, continuously
press 88 (
or
) button to
manual search a station downward
or upward respectively; if press and
hold 88 (
) button for more
or
than 3 seconds, the radio will
Automatically search a station
downward or upward respectively
until it finds a station.
--During playback mode, press
or
and hold 88 (
) button
to fast rewind or fast forward to
reach your desired track quickly.
momentarily pressing 88 (
or
) button, you can select your
desired track downward or upward
Respectively.
Program Playing
--During CD VCD mode ,you
can set the program order to play.
You can follow the steps below:
first, press 16 (PBC) button, and
then press 9 (PGM) button, and
the television displays
programming P00:00. You can set
the program order to play by pressing
14 (0~10+)button, and then press 2
toPlay.
Note: program doesn t function
when playingMP3.
24
On-Screa Display
During CD VCD DVD mode,
press 10 (OSD ) button. The
display shows single track
elapsed time ,single track
remaining or entire disc remaining,
and the track being played and the
content of the whole disc .
Note :During Mp3 mode, only single
track elapsed time is displayed in
OSD mode.
3) You can select the left or the right button to adjust the volume. button
use
to adjust the volume slightly, button
use to adjusts the volume loudly .
4)Click
can choose mute click sound.
5)Press
to save the setting and press
exit.
1.2.Backlight
1)Press the Config Icon on the main menu and then enter into the system
Set-up functions.
2)Press the Backlight Icon on the set up menu.
VOL/BAS/TRE/BAL/FED
Selector
Repeatedly press 11 (SEL)
button to select the desired mode
in the following order:
Press
to darken the screen, press
save the setting and press
exit.
Note: selecting your desired mode, you can
adjust the current mode being displayed
by using (VOL+or VOL-) buttons. When
P-EQ made is activate, press SEL button
to select the modes. And Bass/Treble
Mode are invalid (Show as below)
Repeat Playing /AMS
During DVD mode, first, press 12
(AMS/RPT) to repeat the current
track being played; Press it again to
repeat playing All the tracks.
Pressing it the third time will cancel
the repeating function. (LCD will
display different designs)
to lighten the screen, press
to
1.3.Navisetting
1)Press the Config Icon on the main menu and then enter into the system
Set-up functions.
2)Press the NaviSetting Icon on the set up menu.
3)Click
can auto run navigator application with start. Press
button can enter the interface of the way choice.
13
GPS Operation
4)This interface show all the Folders and execution files. You can copy the
different maps to the SD card and select the path which you choose, and then
press
to make sure. Press
and
can preview page and next
page. Press
exit.
5)Under the NaviSetting interface, press
to save the setting.
PS: This production up to maps as Route66 Horizon PaPaGO Gate5 etc.
1.4.Calibrate
1)Press the Config Icon on the main menu and then enter into the system
Set-up functions.
2)Press the Calibrate Icon enter the calibration program.
3)According the system prompt click the screen exactly. If you want to exit, press
the Return button on the device.
REMOTE CONTROL OPERATION
Replacing the Battery
When the range of the operation of
the card remote control becomes
short or no function with a new
button cell.
1.Pull out the Battery Holder while
Pressing the Stopper
.
Power Button
-- Press 1 ( ) button to turn
On/Off the power.
Pause/Play Button
-- Press 2 (
) button to suspend
The playback of CD MP3 VCD
DVD. Press it again to return to
Normal playback mode.
Mute Button
-- Press 3 ( ) button to cut off
the sound output, Press it again
to resume at the previous sound
Level.
1.5.Language
1)Press the Config Icon on the main menu and then enter into the system
Set-up functions.
2)Press the Language Icon enter the Language setting interface.
2.Put the button-type battery(+) mark
upward into the Battery Holder.
Menu Button
In this menu, can transform the system language into English, traditional Chinese
as well as simplified Chinese. Setting complete, press
to save the setting
and press
exit.
1.6.GPS Test
-- Press 4
to select
Your desired menu. Then press
6 (ENTER) or press the play
Button 2 (
) to confirm.
3.Insert the Battery Holder into the
Remote Control.
Note: This function works in main menu
mode only.
Band/System Switch
Note: Some models are not equipped with
remote control. you should ignore
The contents about remote control.
-- During radio mode, press 5
(BAND/SYS) to switch receiving
Band. Press and hold it, open the
LOUD function.
-- During playback mode, press
5 (BAND/SYS) button to swich
to AUTO PAL or NTSC system,
Press and hold it to open the LOUD
function.
You can know the secondary planet and the orientation from this interface. Click
can exit.
You can know the secondary planet and the orientation from this interface.
Click
can exit.
14
23
GPS Operation
LOCATION OF THE REMOTE CONTROL
Chapter 2.MP3
This chapter introduced how to uses Audio player.
Insulator
Please take off the insulator
Before using the remote.
2.1.Audio player program
1. Select the MP3 icon on the main menu.
2. The program use as MP3 player. The function
characteristic includes:
Play the Audio file/files.
Basic control: play, pause, next song, previous song
Order play and circle play
Press the list icon and then enter the playlist
3. Press
leave the player's interface but still play music in
other interface. Press
13
Random Playing
2.2.Prepare your Audio file
14
Number Button
15
Audio-setting
4
Mute Button
Selecting Menu Button
5
Band/System Switch
Before you use the Audio player program, you must prepare a SD
card to store your Audio file/files, Insert the SD card into the slot.
When you turn on the program, system may automatic sense the
Audio file/files.
6
2
3
16
PBC Menu
17
Subtitle-Setting
Enter Button
18
Playing Time-Setting
2.3.Play music
7
Volume control
19
Mode Switch
1. Select the
8
Tuning/Selecting
Tracks/F.F/REW
20
2. Press
,start playing. Other button's functions show in the
following introduction.
9
Program Playing
Stop/Reverse Button
Angle-Setting
3. The file sensed by the program will become a playlist.
23
Slow-motion Play
Setup Menu
24
Menu-Display
25
Zoom-Setting
10
On-Screen Display
11
Setting the Sound
Characteristics
Re peat Playing
12
22
will leave the Audio player program.
Power Switch
Pause/Play Button
1
21
22
MP3 icon on the main menu then enter the program.
This program support the format of MP3 WMA and WAV, etc.
15
GPS Operation
TV OPERATION(optional)
2.4.Play control
MP3 program can controlled by buttons. Their functions see in table1.
Button
10 TV OPERATION
Play
Play
Previous song
Next song
Mute
Play the previous song
in the list
Play the next song in
the list
6.
Select the downward channel to
watch.
Mute
Volume reduction
Volume reduction
Volume increase
Volume increase
Circle play
circle play file
Order play
Order play file
playlist
Open playlist
Leave player interface
but program is not close
Close Audio player
program
Return
close
table1
2.5.Manage the playlist
If you want to set up your own play list, please according to the process
as below. Edit the list
1.Start up the Audio player program then click
icon
5.Parameter display
After selecting the desired mode,
Y ou can adjust its level by pressing
Area 5 , and the corresponding
parameter will display in this area.
Introduction
Name
7.
Select the upward channel to
watch.
1.SEEK key
Press it, the unit will search
automatically form VHF. When
all the 100 channels are searched
and stored or when the search is
completed, auto-search will stop.
After the auto-search is finished,
the unit will select the first
channel as default.
8.MODE key
Exit the TV mode and return
to main menu.
2.MUTE key
Press it to cut off the sound output,
and
will appear in the LCD.
Press it again to cancel the MUTE
Function.
3.VOL/SEL key
This key has SEL function ,
Repeatedly press it to select mode
4.TA key (optional)
For details, please see Media
Player chapter.
16
21
RADIO OPERATION
Press it to tune a station
downward.Press and hold it for
more than 3 seconds , the radio
will automatically search a station
downward and play when it finds
a Station. You can store the
station by pressing the desired
number control or the desired
stationIn area 12 .
9 Back sight
Press it to enter back sight mode,
And LCD will display rear view.
GPS Operation
2.You can use these three buttons to edit the playlist:
can play the songs which you
.Under the file list, press
selected.
can return the player interface.
3.Click
Chapter 3.MP4
This chapter introduced how to use video player.
Press it to tune a station upward.
Press and hold it for more than 3
Seconds, the radio will automatically
Search a station upward and play
when it finds a station. You can store
The station by pressing the desired
Number key in the remote control or
The desired station in area 12 .
7.Band Selector
Press ir to select bands in the
Following order:
8.
Mute Button
Press
button to cut off the
sound output. Press it again to resume
at the previous sound level.
9.ESC
Exit radio menu and retun to
main menu
20
3.1.Video player program
1. Select the MP4 icon on the main menu.
2. Video player program use as MP4 player. The function
characteristic includes:
Play the video file/files.
Basic control: play, pause, next song, previous song
Order play and circle play
Press the list icon and then enter the playlist
3. Press
will leave the video player program.
3.2.Prepare your video file
Before you use the video player program, you must prepare a SD card
to store your video file/files, Insert the SD card into the slot. When
you turn on the program, system may automatic sense the video
file/files.
3.3.Play video file
1. Select the MP4 icon on the main menu then enter the program.
2. Press
, start playing. Other button's functions show in
following introduction.
3. The file sensed by the program will become a playlist.
4. Press
will leave the video player program.
This program support the format of MP4 WMA and WAV, etc.
17
RADIO OPERATION
GPS Operation
3.4.Play control
Video player program can controlled by buttons. Their functions see
in table2.
button
name
introduction
play/pause
play/pause
Increase the volume
Decrease the volume, appear
the volume pointer
Increase the volume, appear
the volume pointer
playlist
Open playlist
mute
close
Annotate
mute
Close video player program
Table 2
click screen can enter full screen
3.5.Manage the playlist
If you want to browse playlist or choose the video file, please according
to the process as below.
1.Start up the video player program then click
interface as below.
icon, then enter the
2.You can use these three buttons to edit the playlist:
can play the songs which you
.Under the file list, press
selected.
can return the player interface.
3.Click
18
3.PTY key
Press PTY key to select program type:
Press touch area 12 to select
programme Contents as follows:
(A) PTY MUSIC group:
1. POP M, ROCK M.
2. EASY M, LIGHT M.
3. CLASSICS, OTHER M.
4.JAZZ, COUNTRY .
5. NATION M, OLDIES.
6. FOLK M.
stop
stop
Decrease the volume
Radio(RDS is optional)
1.AF key
Alternative frequency tracking, The
radio automatically selects the
alternative frequency of the same
programme with the reception.
When AF is on, AF in the LCD
With be flashing, when AF is off,
AF in the LCD disappear.
2.TA key
Traffic program/Traffivc Announcement.
When TA is on, TA in the LCD will
display and 10 will appear TASEEK .
After TA information os searched,
10 will display the corresponding
Frequency. If no TA information
is searched, NO Ta will display
in the LCD and it automatically
switches to normal mode.
(B) PTY SPEECH group:
1.NEWS, AFFAIRS, INFO.
2. SPORT, EDUCATE, DRAMA.
3. CULTURE, SCIENCE, VARIED.
4.WEATHER, FINANCE, CHILDREN.
5. SOCIAL, RELIGION, PHONE IN.
6. TRAVEL, LEISURE, DOCUMENT.
The radio will start searching
corresponding PTY information and
Is stops when the inf ormation isfound.
if there are no PTY information, it
automatically switches to normal
mode.
4. APS key.
Pres it to start automatic scanning of
radio stations .The unit will automa-tically pick up the station and store in
to area 12 . A total of 18 FM stations
and 12 AM stations will be stored.
After all the stations are stored
station. The unit will start playing the
first station stored till the last station
stored
19
Open as PDF
Similar pages