Mitsubishi Electric LT-46164 LED TV

IMMERSIVE SOUND LED LCD HDTV
with Integrated Sound Projector
MODELS
154 Series
164 Series
265 Series
OWNER’S GUIDE
•
•
•
•
For questions:
-- Visit our website at www.mitsubishi-tv.com.
-- E-mail us at MDEAservice@mdea.com.
-- Call Consumer Relations at 800-332-2119 for operational or connection assistance.
For information on System Reset, please see the back cover.
To order replacement or additional remote controls, visit our website at www.mitsuparts.com or call
800-553-7278.
265 Series. IR emitter cables for NetCommand home-theater control are available for purchase from
Mitsubishi. Call 800-553-7278 and request either part number 242D483020 (two-ended cable) or part
number 299P254020 (four-ended cable).
®
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user of the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
WARNING: This product shall be connected to a MAINS
socket outlet with a protective earthing connection.
MAINS DISCONNECTION: The mains plug is used
as the disconnect device. The mains plug shall remain
readily operable.
WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
This apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
WARNING: This product contains chemicals known
to the State of California to cause cancer and/or birth
defects or other reproductive harm.
TV WEIGHT: This TV is heavy. Exercise extreme care
when lifting or moving it. Lift or move the TV with a
minimum of two adults. To prevent damage to the TV,
avoid jarring or moving it while it is turned on. Always
power off your TV, unplug the power cord, and disconnect all cables before moving it.
Note: Features and specifications described in this
owner’s guide are subject to change without notice.
For assistance call 1(800) 332-2119
FCC Declaration of Conformity
Product:
LCD Flat Panel HDTV
Models:
LT-55154
LT-40164, LT-46164, LT-55164
LT-46265, LT-55265
Responsible
Party:
Mitsubishi Digital Electronics
America, Inc.
9351 Jeronimo Road
Irvine, CA 92618-1904
Telephone:
(800) 332-2119
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and the receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications not expressly
approved by Mitsubishi could cause harmful
interference and would void the user’s authority
to operate this equipment.
Contents
Important Information About Your TV
Installation and Operating Notes. . . . .
Important Safety Instructions. . . . . . .
. . . . . . . . .
4
5
. . . . . . . . . . . . . . . . . . . . . . . .
6
. . . . . . . . . . . . . . . . . . . . . . . . . .
7
Stand Installation..
Wall-Mounting. .
. . . . . . . . .
1 Basic Setup and Operation
Package Contents. . . . . . . . . . . . . . . . .
Before You Begin.. . . . . . . . . . . . . . . . .
First-Time Power-On.. . . . . . . . . . . . . . .
TV Controls. . . . . . . . . . . . . . . . . . . . . .
Remote Control. . . . . . . . . . . . . . . .
The TOOLS Key and Menu. . . . . . . .
TV Control Panel. . . . . . . . . . . . . . .
POWER Indicator. . . . . . . . . . . . . . .
Setting Up TV Inputs. . . . . . . . . . . . . . .
Basic TV Operation. . . . . . . . . . . . . . . .
Using the TV with a Personal Computer. .
. . . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
9
10
10
11
11
12
13
13
14
16
19
2 TV Connections
Before You Begin.. . . . . . . . . . . . . . . . . . . . . . . 21
Connection Types and Audio/Video Quality .. . . . 21
Inputs and Outputs. . . . . . . . . . . . . . . . . . . . . . 22
Cable Routing. . . . . . . . . . . . . . . . . . . . . . . . . . 22
HDMI Device.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Y Pb Pr Component Video Device. . . . . . . . . . . . 25
DVI Video Device. . . . . . . . . . . . . . . . . . . . . . . . 25
Antenna or Cable TV Service.. . . . . . . . . . . . . . . 26
Composite Video Device.. . . . . . . . . . . . . . . . . . 26
VCR or DVD Recorder to an Antenna or
Wall Outlet Cable. . . . . . . . . . . . . . . . . . . . . . . 26
A/V Receiver. . . . . . . . . . . . . . . . . . . . . . . . . . . 27
A/V Receiver with HDMI Output. . . . . . . . . . . . . 27
Supplemental Audio Connections . . . . . . . . . . 28
3 TV Features
Sleep Timer.. . . . . . . . . . . . . . . . . .
FAV (Favorite Channels). . . . . . . . . .
ChannelView Channel Listings.. . . . .
Status Display. . . . . . . . . . . . . . . . .
Using an External Sound System.. . .
Picture Shape and Display Formats. .
Camera Images and Music Files. . . .
USB Source Devices. . . . . . . . .
Photos and Motion Video as
Composite Video. . . . . . . . . . .
Using an Audio-Only Device. . . .
Wireless Audio Playback.. . . . . .
Sound Projector.. . . . . . . . . . . . . . . .
StreamTV™ Internet Media. . . . . . . . .
Introduction to Home-Theater Control.
4 TV Menus
Main Menu.
Picture. . . .
Sound.. . . .
Captions. . .
Setup. . . . .
Inputs. . . . .
Lock. . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
29
29
30
31
32
33
34
34
. . . . . . . .
. . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
5 NetCommand IR Control
About NetCommand IR Control.. . . . . . . . . .
IR Emitters. . . . . . . . . . . . . . . . . . . . . . . . .
NetCommand Setup.. . . . . . . . . . . . . . . . . .
Operating NetCommand-Controlled Devices.
. . .
. . .
. . .
. . .
6 NetCommand IR Control of an A/V Receiver
Controlling an A/V Receiver after NetCommand
Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Up A/V Receiver Control
Power and Volume. . . . . . . . . . . . . . . . . . .
Automatic Audio/Video Switching Over
an HDMI Connection. . . . . . . . . . . . . . . .
60
61
62
63
.
68
.
69
.
.
73
79
81
84
85
. . . . . . . . .
92
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
99
Programming the Remote Control.
Bypassing the Parental Lock. . . . .
HDMI Control of CEC Devices. . . .
TV Care.. . . . . . . . . . . . . . . . . . .
Troubleshooting. . . . . . . . . . . . . .
Trademark and License Information. .
Index. .
46
46
49
51
52
55
57
67
Appendices
Appendix A:
Appendix B:
Appendix C:
Appendix D:
Appendix E:
Warranty.
38
42
45
.
Network Service Disclaimer. .
. . . . . . . . .
. . . . . . . .
.
.
.
. . . . . . . . . . . . . .
100
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
101
36
36
37
For assistance call 1(800) 332-2119
4
Important Information About Your TV
For Your Records
Record the model number, serial number, and
purchase date of your TV. The model and serial
numbers are on the back of the TV. Refer to this
page when requesting assistance with the TV.
MODEL NUMBER
SERIAL NUMBER PURCHASE DATE
RETAILER NAME LOCATION
Installation and Operating Notes
Custom cabinet installation must allow for proper
air circulation around the television.
NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER
IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S
ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND,
IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND
SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF
THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY
AS PRACTICAL.
TV Software
Do not attempt to update the software of this TV with
software or USB drives not provided by or authorized
by Mitsubishi Digital Electronics America, Inc. Nonauthorized software may damage the TV and will not be
covered by the warranty.
Children and TV Viewing
The American Academy of Pediatrics discourages
television viewing for children younger than two years of
age.
For assistance call 1(800) 332-2119
If Your TV Gets Damaged
Crystalline liquid may leak from the LCD panel and
broken glass may be scattered.
CAUTION: The crystalline liquid is toxic. Avoid
contact with your skin, eyes, or mouth. DO NOT
touch the broken glass or crystalline liquid. DO NOT
get glass fragments or crystalline liquid into eyes or
mouth. Should either contact your eyes or mouth,
rinse the contacted area thoroughly with water and
consult your doctor.
Disposal of Your TV
The LCD panel contains a small amount of crystalline
liquid which is toxic and should not be touched.
DO NOT dispose of the TV with general household
waste. For disposal or recycling information, contact
your local authorities or the Electronic Industries Alliance at www.eiae.org.
5
Important Safety Instructions
Please read the following safeguards for your TV and
retain for future reference. Always follow all warnings
and instructions marked on the television.
E XAMP LE OF ANT E NNA G R OUNDING
1) Read these instructions.
2) Keep these instructions.
ANT E NNA
LE AD IN WIR E
G R OUND C LAMP
ANT E NNA
DIS C HAR G E UNIT
(NE C AR T IC LE 810-20)
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
E LE C T R IC
S E R V IC E
E QUIP ME NT
6) Clean only with dry cloth.
G R OUND C LAMP S
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
G R OUNDING
C ONDUC T OR S
(NE C AR T IC LE 810-21)
NE C — NAT IONAL E LE C T R IC AL C ODE
P OWE R S E R V IC E G R OUNDING
E LE C T R ODE S Y S T E M
(NE C AR T 250, P AR T H)
Outdoor Antenna Grounding
If an outside antenna or cable system is connected
to the TV, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges.
Replacement Parts
When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart,
stand, tripod, bracket,
or table specified
by the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving
the cart/apparatus
combination to avoid
injury from tip-over.
13) Unplug this apparatus
during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
For assistance call 1(800) 332-2119
6
Stand Installation
•
•
CAUTION
Using this TV with other than the authorized accessories may cause the TV to become unstable, which
can cause damage to the product or possible injury.
At least TWO PEOPLE are required to install the stand. Support the TV near the corners as shown. Failure to follow
these recommendations may result in personal injury and damage to the product.
Note
• 40- or 46-inch TV: If planning to wall-mount the TV, there is no need to install the stand.
• 55-inch TV: The TV comes from the factory with the stand pre-installed.
Required: Phillips Screwdriver
Extension pieces
pieces
on Extension
back of stand
on back of stand
11
Back
22
BACK
DO support the TV
DO support
the TV
under
the corners.
under the corners.
Two adults are required to lift the TV.
Two adults are required to lift the TV.
33
DON’T place your hand where it can
get caught under the TV.
DON’T place your hand where it can get
caught between the TV and stand.
TV in protective
TV wrapping
in protective
wrapping
Stand
Repacking the
Repacking the Stand
CAUTION. Place the
CAUTION.
stand
in the foam Place
insert the
TV
TV
stand
in the foam
insert
with
the extension
pieces
with
the
extension
pieces
facing away from the TV.
facing away
from
the
Otherwise,
the TV
will
beTV.
Otherwise,
the
TV
will
be
damaged in transit.
damaged in transit.
Protect the TV and
Protect
and
stand
withthe
theTV
original
stand
with
the
original
packing material.
packing material. Extension pieces on stand
Extension
stand
must
face out,pieces
away on
from
TV.
must face out, away from TV.
For assistance call 1(800) 332-2119
7
Wall-Mounting
To order a wall-mount kit, please contact Peerless Industries, Inc. at (800) 473-3753 or visit
www.peerlessmounts.com. Order wall-mount kit model
ST650.
To order a wall-mount kit from Mitsubishi Digital Electronics America, Inc., please visit www.mitsuparts.com
or call (800) 553-7278.
Complete installation instructions are included with the kit.
Stand Removal Prior to Wall-Mounting
CAUTION
At least TWO PEOPLE are needed to safely remove the stand. Have one person hold the TV while the other person
removes the stand. Failure to follow these recommendations may result in personal injury and damage to the product.
Note
• 55-inch TV: Remove the factory-installed stand prior to wall-mounting.
• 40- or 46-inch TV: If you installed the stand for table-top use, follow these instructions to remove it prior
to wall-mounting the TV.
1. Disconnect the TV’s AC power cord from the AC
2.
3.
4.
5.
power outlet.
Spread the protective sheet that was wrapped
around the TV on a flat, even surface, such as a
sturdy table. The protective sheet will help prevent
damage to the display.
IMPORTANT: To avoid damaging the screen,
make sure there are no foreign objects under or
on top of the protective sheet.
Position one person on each side of the TV (left and
right sides). Have each person firmly grasp their side
of the TV and gently place it face down on the protective sheet with the display stand hanging over the
edge of the table. See the illustration to the right.
Use a magnetic philips screwdriver to remove the
stand screws from the recessed holes (see illustration to right). Note: A regular screwdriver can be
used with a separate magnetic pick-up tool.
While one person holds the TV with both hands,
have the other person grasp the stand (see illustration to the right) and remove the stand by pulling it
away from the TV in the direction of the large arrow
shown in both illustrations.
1SPUFDUJWF
TIFFU
57
4UBOE
5BCMF
55-inch TVs
(6 screws)
40- and 46-inch TVs
(4 screws)
Protective
Sheet
Pull stand
to remove.
For assistance call 1(800) 332-2119
8
Special Features of Your TV
Your new high-definition widescreen television has
many special features that make it the perfect center of
your home entertainment system, including:
1080p High-Definition LCD Display System
Your Mitsubishi LED LCD HDTV uses a full 1920 x 1080
LCD panel to create the picture you see on the screen. All
images are displayed at 1080p. The TV uses new Plush
1080p® 5G digital video processing to convert lower-resolution signals to 1080p for display.
True120Hz and True240Hz
True120Hz (154 and 164 series) and True240Hz (265 series)
make fast-moving images appear smoother and more fluid,
free from motion blur. It does this by doubling the traditional progressive scan frame rate and creates new frames
of video between the traditional frames to create smoother
moving images. True120Hz/True240Hz also smooth film
judder (image vibration) that may be present in film-based
content such as movies.
16:9 Widescreen Picture Format
Enjoy a full theatrical experience in the comfort of your
home. View pictures as film directors intended them.
Digital TV broadcasts, DVDs and newer video game
consoles support this widescreen format.
Integrated HDTV Tuner
Your widescreen Mitsubishi HDTV has an internal HDTV
tuner able to receive both over-the-air HDTV broadcasts (received via an antenna) and non-scrambled
digital cable broadcasts, including non-scrambled
HDTV cable programming.
High-Definition Video Inputs
•
•
Component Video Inputs. Also called Y/Pb/Pr
inputs, these inputs receive standard analog video
formats of 480i, 480p, 720p, and 1080i high-definition signals. This provides a high level of flexibility
when connecting DVD players/recorders, cable
boxes, and satellite receivers.
HDMI Inputs. These inputs accept digital 480i,
480p, 720p, 1080i, and 1080p video signals plus
bitstream and PCM digital stereo signals. The
HDMI™ inputs can also accept a variety of PC
signals and resolutions.
Used with an adapter, these inputs also accept
compatible digital DVI video signals. HDMI
inputs provide additional high-performance,
high-definition connections for maximum flexibility
in your choice of home theater products. The HDMI
inputs are HDCP copy-protection compatible.
For assistance call 1(800) 332-2119
Easy Connect Auto Input Sensing
Easy Connect™ Auto Input Sensing automatically recognizes when you plug in a device and prompts you to
assign a name to it.
Home-Theater Control
HDMI Control
Available on all models. HDMI devices with Consumer
Electronics Control (CEC) capabilities may be compatible
with the TV’s HDMI Control feature. Compatible devices
can receive control signals through the HDMI connection,
allowing the TV’s remote control to operate some functions of these devices.
NetCommand with IR Learning
265 Series. NetCommand® supports IR (infrared) control
of products such as VCRs, DVD players, cable boxes,
and satellite receivers. NetCommand can “learn” remote
control signals directly from many devices, allowing you
to create a customized NetCommand-controlled hometheater system.
Sound Projector
Sound Projector technology uses the TV’s bank of
speakers to create a simulated surround sound effect
by reflecting sound off the room walls.
StreamTV™ Internet
StreamTV brings many popular internet applications to your
TV. Among them is the VUDU™ movie service, offering the
largest on-demand HD movie selection anywhere, featuring full 1080p and 5.1 surround sound. VUDU allows you
to enjoy movies with no store visits, no mailing, no late fees
and no subscriptions.
ENERGY STAR®
This is an ENERGY STAR® qualified TV. Products that
earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy efficiency guidelines set
by the U.S. Environmental Protection Agency and the
U.S. Department of Energy.
This TV uses power within ENERGY STAR guidelines
except when Picture Mode is set to Brilliant.
1
9
Basic Setup and Operation
Package Contents
Please take a moment to review the following list of
items to ensure that you have received everything.
Installing the Remote Control
Batteries
1. Remove the remote control’s back cover by
Remote Control
Two AA Batteries
2.
AA
AA
3.
gently pressing in the tab and lifting off the cover.
Load the batteries, making sure the polarities
(+) and (-) are correct. For best results, insert
the negative (-) end first.
Snap the cover back in place.
1
The remote
control requires
two AA alkaline
batteries.
Basic Owner’s Guide
Quick Setup Guide
2
Product Registration
Card
Power Cord
Cable Ties
Stand Screws (40- and
46-inch TVs only)
265 Series. Calibration
Microphone
For assistance call 1(800) 332-2119
10
1. Basic Setup and Operation
Before You Begin
1. Review the important safety, installation, and oper2.
ating information at the beginning of this book.
Choose a location for your TV.
• See the stand-installation or wall-mounting
requirements starting on page 6.
• Allow at least four inches of space on all sides
of the TV to help prevent overheating. Overheating may cause premature failure of the TV.
• Avoid locations where light may reflect off the
screen.
3. Install the batteries in the remote control.
4. Plug the TV into an AC power outlet.
First-Time Power-On
1. Press the
TV key to
ensure that the remote
control is in TV mode.
TV
TV
2. Aim the emitter end of the
remote control at the TV
and press the POWER key
. Wait for the Welcome
screen.
3. If you wish to change the
menu language to Español,
press .
4. Press
to move to the
energy-mode selections.
Select Home.
5. Press
TV power connection
TV Tips
Turning the TV On or Off
•
•
Point the emitter (bulb) end of the remote
control at the front of the TV and press the
POWER button.
Press the POWER button on the TV control
panel.
Controlling Sound Volume
•
•
Press VOL to adjust the sound level.
See also “Controlling A/V Receiver Sound
Volume” on page 32.
For assistance call 1(800) 332-2119
to highlight EXIT.
Press ENTER to clear the
menu.
Welcome Screen Energy Options
•
•
Mitsubishi recommends the Home setting,
which uses power within ENERGY STAR®
guidelines.
The Retail setting looks best under bright
lighting. In this mode, the TV uses power in
excess of ENERGY STAR guidelines.
This table compares energy choices offered in the
Welcome screen.
Home
Retail
Picture Mode
Bright
Brilliant
Backlight Level
Reduced
Brightness
Full Brightness
1. Basic Setup and Operation
11
TV Controls
Remote Control
For more on use and care of the remote control, see
page 84.
Sleep Timer, page 29
Number/letter keys
Channel tuning, page 16
Pass-code entry, page 57,
page 43
Adds a separator in digital channel
numbers. Clears some menu entries.
Emitter (Bulb) End
TV CAB/SAT DVD AUDIO VCR
Press the key for the device type to
control. Leave in TV mode for normal
TV viewing.
Powers TV on or off.
LAST Returns to the previous channel;
moves back one menu
MUTE Mutes the TV speakers.
TOOLS Displays shortcuts for the number keys.
Press to check if shortcuts are available
for the current device. See the next
page.
FAV
Displays up to nine favorite
sources, page 29.
FORMAT
Changes picture shape,
page 18
VOL Controls volume of TV speakers.
INTERNET
CH Changes channels; moves to another
PAGE page in a menu or list.
Connects to StreamTV internet
content, page 42.
INPUT
Press to select a TV input,
page 16.
ENTER
Selects a channel number or menu item.
Navigation and adjustment
controls
GUIDE ChannelView listings, page 30.
INFO
AUDIO
Audio settings, page 49
VIDEO
Video settings, page 46
MENU
Displays or clears the TV main
menu (page 46). Also steps
back one menu.
TV status or TV help.
(Pause) Freezes a broadcast TV picture.
Record/Playback controls for external devices
When remote control is programmed, page 73
HDMI control, page 83
265 Series: With NetCommand, page 66
Note: To operate other audio/video devices using the
TV’s remote control, use any of these methods:
• See Appendix A, “Programming the Remote
Control.”
• For HDMI devices compatible with the TV’s HDMI
Control feature, see Appendix C.
EXIT
Clears all menus.
F1–F4. 265 Series. Special keys for
use with NetCommand IR control. See
“Initial NetCommand Setup”.
• 265 Series
-- See page 60 for NetCommand IR “Learning” of
device keys.
-- For use of specific keys with NetCommandcontrolled devices, see “Special Operation
Methods,” page 64.
For assistance call 1(800) 332-2119
12
1. Basic Setup and Operation
TV Controls, continued
The TOOLS Key and Menu
Press the TOOLS key to check for shortcuts. The Tools menu lists shortcut keys
for common functions. Press the number key to activate the shortcut. See the
sample menu below.
• Shortcuts specific to the current device are in the third column.
• Shortcuts may be available for a CEC-enabled device. See Appendix C,
“HDMI Control of CEC Devices,” page 81.
• 265 Series. After setting up NetCommand control for a device, check the
Tools menu for shortcuts. See page 62.
TOOLS
TOOLS
Tools
PICTURE SOUND
TV
Device-Specific Shortcuts
Availability varies, depending on equipment features and setup.
3 CC. Turns closed
captions on/off
page 51
Sample Tools menu
Sound Shortcuts
Picture Shortcuts
1 Picture Mode Brilliant
page 46
4 Picture Mode Natural
164 and 265 Series. Brilliant and
page 48
Natural Picture Modes are the
default choices. If your installer has
set up special Picture Modes in the
Picture > Advanced menu, select
them from this menu.
7 Backlight turns off the backlight.
Press any number key to turn the
backlight back on.
---
For assistance call 1(800) 332-2119
2 Subwoofer. Turns on or off audio to a con- page 50
nected subwoofer.
5 Surround. Selects Sound Mode Surround page 50
8 Night. Selects Sound Mode Night
1. Basic Setup and Operation
13
TV Controls, continued
TV Control Panel
System Reset
Buttons on the control panel duplicate some keys on
the remote control.
• To display the main menu, press INPUT and VOL+
simultaneously for about 10 seconds. Press and
hold INPUT and VOL+ for 10 seconds to clear the
menu.
• Refer to left labels when no TV menus are displayed.
• Refer to right labels when using TV menus or after
activating a special function.
If the TV fails to respond to the remote control, the
control-panel buttons, or will not power on/off, perform
System Reset. Recent setting changes made before
using System Reset may be lost.
POWER
To perform System Reset, press and hold the POWER
button on the control panel for 10 seconds.
Panel-Lock Release
•
•
To release the Panel Lock using the TV control
panel, press and hold the INPUT button on the
control panel for ten seconds. If the TV is off, press
the POWER button to make it power on.
To activate the Panel Lock, use the Lock menu,
page 59.
INPUT
ENTER
CH
VOL
TV control panel
POWER Indicator
POWER
Key
Off
Steady On
Slow Blinking
Fast Blinking
LED Color TV Condition
None
TV is powered off. Normal operation.
Green
TV is powered on. Normal operation.
Green
TV powered off, auto-on TV Timer is set.
Normal operation. TV can be turned on at any time.
Red/
Yellow
TV may require service.
• Hold power button on front panel for 10 seconds to reset TV.
• If LED continues to flash red and yellow after reset, turn off the
TV and unplug it from the AC power source. Wait one minute
and then plug the set back in.
• If LED continues to flash red and yellow, go to
www.mitsubishi-tv.com or call 1-800-332-2119 to receive Authorized Service Center information.
You may be asked to count how many times the LED flashes
each color to assist in troubleshooting.
For assistance call 1(800) 332-2119
14
1. Basic Setup and Operation
Setting Up TV Inputs
Using the ANT (Antenna) Input
If using an antenna or direct cable service (no cable
box), connect the incoming coaxial cable to the TV’s
ANT input. Refer to page 26.
You must perform a channel scan to enable reception of digital channels. If you skip this step, the TV
will receive only analog channels. The channel scan
will search for high-definition and standard-definition
channels available in your area.
Memorizing Channels with Channel Scan
Setting Up Inputs with Auto Input Sensing
1. Power on the TV.
2. Power on the devices to ensure detection.
3. Connect one device to the TV, making note of the
4.
TV input jack.
The TV will display the New Device Found screen if
the connection type is detectable.
Highlight the device type in the on-screen list and
press ENTER. The name you select here will appear
in the Input Selection menu.
For the ANT input
To start channel memorization
1. Power on the TV.
2. Press MENU and open the Setup > Channel menu.
Start channel memorization from the Setup > Channel
menu.
3. Press to enter the menu.
4. Highlight Ant Air if connected to an
over-the-air antenna. Highlight Ant
Cable for service over direct cable
(no cable box). Press ENTER to add a
check.
5. Select the scan type.
•
•
For first-time setup, highlight All
channels.
To scan for channels not already
in memory, highlight New only.
Press ENTER to add a check.
6. Highlight Scan and press ENTER.
Channel memorization may take up
to 15 minutes to complete.
To stop channel memorization before completion,
press CANCEL.
At any time after Channel Scan,
• Use the Setup > Channel > Edit menu (page 53) to
add or delete individual channels from memory.
• Perform an additive scan with the New only option
to add channels not already in memory.
• Repeat the All channels scan if you move the TV
to a new geographic area with a different channel
line-up or reposition the antenna.
For assistance call 1(800) 332-2119
Sample New Device
Found screen.
Important Note for NetCommand Users
265 Series. Be sure to select the correct device
type here. Although you can change the device type
later using the Inputs > Name menu, any “learned”
NetCommand IR codes will be erased when you
make the change.
5. Press EXIT to close the New Device Found screen.
6. Repeat the preceding steps for each for each additional device you want to add.
1. Basic Setup and Operation
15
Setting Up TV Inputs, continued
About Auto Input Sensing
Tips on Auto Sensing
This TV’s Easy Connect™ Auto Input Sensing feature
detects the following connections automatically:
• Analog video jacks from inputs 1, 2, and 3
• HDMI inputs (when powered on)
• USB device containing photo and music files
(JPG and MP3 formats).
•
•
Auto Input Sensing for Most Devices
When you first connect a device, the TV will:
a. Detect the connected device and automatically switch to it.
b. Prompt you to identify the device type.
c. Repeat these steps for other newly detected
devices.
•
•
•
•
When You First Connect a Device
•
•
•
Most Device Types. Select the device type from
the on-screen list. The device type you select here
will appear as an icon in the Input Selection menu.
A/V Receiver. For an HDMI-equipped A/V
receiver, select AVR from the list of device types if
the A/V receiver is not recognized automatically.
HDMI CEC Devices Compatible with the
TV’s HDMI Control Feature. Compatible
CEC-enabled HDMI-equipped devices are often
recognized automatically by the TV. HDMI Control
may allow you to control some functions of a CECenabled device. See Appendix C, “HDMI Control
of CEC Devices.”
Choose a different name for each input.
The antenna input (ANT) is never detected,
although you can turn off the unused antenna
input in the Inputs > Name menu.
Change the device type displayed in the Input
Selection menu by using the Inputs > Name
menu (page 55).
Some HDMI devices can automatically tell the TV
what name to use in the Input Selection menu
and you will be unable to change the name.
The TV is unable to detect a new connection if
the current input is USB, Bluetooth®, or internet.
Switch to a different input before connecting.
265 series. Any “learned” NetCommand IR
codes will be erased if you change the device
type in the Inputs > Name menu.
Reactivating Auto Input Sensing
for an HDMI Input
After you disconnect an HDMI device, Auto Input
Sensing is temporarily disabled. Perform these
steps:
1. Disconnect the HDMI device.
2. Delete the removed HDMI device in the Inputs >
3.
Name menu (see “Removing an HDMI Device,”
page 83).
Connect the new device and the New Device
Found screen will display.
New Device Found screen for a device with HDMI
control enabled. Select On if you want to enable the
TV’s HDMI control of the device. In some cases, as
in the example above, you will also be prompted to
select a device name.
For assistance call 1(800) 332-2119
16
1. Basic Setup and Operation
Basic TV Operation
Selecting an Input to Watch
Watching Broadcast TV
TV Connected to an Antenna or Direct Cable
Service (no cable box)
1. Press INPUT.
Note: Perform channel memorization to enable reception of digital channels. See page 14.
2. Press
1. Press INPUT to display the Input Selection menu.
2. Highlight the antenna or cable icon and press ENTER.
and
to highlight an input icon.
Sample Input Selection menu, antenna input selected
Sample Input selection menu, DVD input selected
3. Press ENTER to switch to the input.
4. To control the input device, use the device’s remote
control or see “Introduction to Home-Theater
Control,” page 45.
Note: In most cases, to see a named icon for a connected device (as in the samples), you must first
assign a name either
• When the device is first connected and the
New Device Found menu offers a choice
of names.
• By using the Inputs > Name menu to
assign or change a name at any time after
the TV has detected the connection.
More About the Input Selection Menu
To assign helpful names to the icons, see the
Inputs > Name menu, page 55.
• To remove unwanted Antenna, Bluetooth®, or HDMI
device icons from the Input Selection menu, see
the Inputs > Name menu, page 55.
• To rearrange the icons, see the Inputs > Order
menu, page 56.
•
For assistance call 1(800) 332-2119
3. To tune to a channel from the ANT input, use any of
these methods.
• Enter the channel number using the number
keys on the remote control and press ENTER.
For a two-part digital channel, such as 3-1,
—
press 3 CANCEL 1 ENTER .
• Press CH to change channels one channel at a
time.
• Press and hold CH to speed through channels.
•
•
•
•
Press LAST to return to the previous channel.
Use the Fav (Favorites) feature to tune to up to
nine favorite channels. See page 29.
Press GUIDE to display ChannelView channel
listings, highlight a channel number, and press
ENTER to tune.
Set up ChannelView custom channel banks
and use the CH / key to tune to predefined
groups of channels. See page 30.
1. Basic Setup and Operation
17
Basic TV Operation, continued
Picture Settings
Basic Audio Controls
1. To get the best picture under different viewing con-
Controlling Sound Volume
ditions, set the Picture Mode first before changing
other video settings. See page 46.
•
•
a. Press VIDEO.
b. Press
until Picture Mode
displays.
•
c. Press
to make one of these selections:
Name
Brilliant
When to Use
Under bright light
Game
Bright
With gaming consoles (inputs
named Game or PC only)
For most daytime viewing
Natural
For most nighttime viewing
Changing Audio Settings (TV Speakers Only)
2. Press
3.
4.
to display the name of another adjustment.
Press
to make the adjustment.
Press EXIT to clear the display.
Additional picture options are available through these
menus:
Menu Name
Picture > Video
Press VOL to adjust the sound level
of the TV speakers.
Control subwoofer volume with an
on-screen slider. See page 49. Set
Sound > Global > Subwoofer to
On to make this adjustment available.
See also “Controlling A/V Receiver
Sound Volume” on page 32.
Page
46
Picture > Picture Plus
47
Picture > Perfect (265 Series)
48
Picture > Advanced (164 and 265 Series)
48
1. Press AUDIO.
2. Press
to find the adjust-
ment you want. See page 49.
to change.
3. Press
Changing the Audio Output
To switch from the internal TV speakers to an external
sound system,
1. Press AUDIO.
2. Press
to display the TV Speakers option.
3. Press
to change to Off.
TV Care
See page 84.
Assistance
•
•
For troubleshooting, service, and product support,
see Appendix E, starting on page 85.
For warranty information, see page 99.
For assistance call 1(800) 332-2119
18
1. Basic Setup and Operation
Basic TV Operation, continued
The FORMAT Key and Picture Shape
Repeatedly press the
FORMAT key to cycle
through displays for the
current program. The
TV will remember the
format you last used on
each input.
For details, see page 33
Important
Black bars at the edges of
the screen are common in HD
pictures. Black bars are not a
defect of the TV.
• Black bars are added by broadcasters to fill the 16:9 screen
area while preserving the original
aspect ratio of the picture.
• Your cable box, satellite receiver,
or other device may also be
altering the broadcast picture.
If your device offers output in
native format, try using it with
Mitsubishi picture formats.
Sample Uses of the FORMAT Key
You can use the FORMAT key to reduce or eliminate black areas at the
edges of the picture.
Press
Squarish 4:3 image is
narrower than the 16:9
screen; unused areas at the
sides are filled with black.
Wide Expand mode stretches
the picture sideways to fill the
screen.
Press
Wide 2.35:1 anamorphic DVD
image; unused areas at the
top and bottom are filled with
black (letterbox effect).
Zoom mode. The picture fills
the screen. All four edges are
cropped in this mode.
More TV Features
Feature
Page
Parental controls (Lock menu)
57
Audio Lock (controls your sound system with
the TV’s remote control left in TV mode.)
74
TV Clock. Set the TV Clock if you plan to use
the TV Timer (page 52) or ChannelView (page
30).
52
Favorite channels or sources
29
ChannelView and custom channel collections
30
Changing the input names that appear in the
Input Selection menu (Inputs > Name menu)
55
Digital camera images and mp3 music files
34
164 and 265 Series. Listening to a wireless
audio device with the TV speakers
37
StreamTV™ internet access
42
For assistance call 1(800) 332-2119
Feature
Page
Programming the remote control to operate
other A/V devices
73
Controlling compatible devices using HDMI
CEC control
81
265 Series. Controlling A/V devices with NetCommand
60
19
1. Basic Setup and Operation
Using the TV with a Personal Computer
Connecting a Computer to the TV
HDMI Connection
Use one of the connection methods listed below based
on your computer’s video output.
Mitsubishi recommends using high-speed HDMI
cables to connect newer devices incorporating HDMI
technology.
Computer
Video Output
Digital DVI
HDMI
Video Connection
Audio
Connection
DVI-to-HDMI cable Analog audio
or an HDMI cable
cable with mini
with a DVI-to-HDMI plugs
adapter
HDMI-to-HDMI
cable
IMPORTANT
This TV accepts digital computer
video signals only. This TV is not
compatible with VGA (analog)
computer video.
No additional
audio connection is required.
HDMI-to-HDMI
cable
TV
VGA
PC MONITOR OUT
1. Connect the computer’s digital signal output to one
2.
Computer with
HDMI output
of the TV’s HDMI jacks. See the connection diagrams for the method suited to your equipment.
Connect the computer’s audio output using one of
these options:
• For digital DVI video signals, connect the
analog audio output to the TV’s DVI/PC AUDIO
INPUT jack.
• For HDMI signals, no additional audio connection is required.
Note: If you are unable to hear audio from the
computer, there may be an incompatibility in
the computer’s hardware, software, or internal
settings. Consult a trained computer technician
for advice.
3. Power on the TV and computer. The TV will detect
the connection and display the New Device Found
screen.
4. In the New Device Found screen, press
to
highlight PC in the list of device types. It is important to use the name PC so that the TV processes
the PC signal correctly.
5. Highlight EXIT and press ENTER to close the New
Device Found screen.
An HDMI-to-HDMI connection carries all video and
audio on a single cable.
HDMI and Digital Surround Sound
The TV’s HDMI inputs can receive digital surround
sound from an HDMI device. Use an HDMI connection if you want to hear digital surround sound from
the TV’s internal speaker array.
DVI Video Connection
Computer
with Digital
DVI output
AUDIO
OUT
Audio cable
DVI OUT
Note: If your computer provides digital audio output
(coaxial or optical), you can connect it directly
to a digital A/V receiver and bypass the TV.
TV
DVI-to-HDMI
cable
A DVI connection from a personal computer requires a
separate audio connection.
For assistance call 1(800) 332-2119
20
1. Basic Setup and Operation
Using the TV with a Personal Computer
Computer Video Adjustments
1. Power on the computer.
2. Select PC from the Input Selection menu. To do
3.
4.
5.
Tip
Set the computer’s screen saver to display a pattern
after several minutes of inactivity. This acts as a
reminder that the TV is powered on.
this, press INPUT to open the Input Selection menu,
move the highlight to the PC icon, and press ENTER.
Working from the computer, change
the resolution of the computer image.
Computer Display Formats
View the computer image on the TV
and maximize the computer resolution
Press FORMAT repeatedly to cycle through the TV displays available
while maintaining a suitable aspect
for your computer’s video signal.
ratio for the image.
Perform TV video adjustments. Press
Computer Signal
As Displayed on TV Screen
VIDEO repeatedly to access video4X3
16 X 9
Original Format
Zoom
adjustment options.
Standard
Standard
Press FORMAT repeatedly to find the
VGA
picture shape best suited to the
640 X 480
image. See the chart on this page
showing how different computer resolutions can be displayed on the TV.
SVGA
800 X 600
Distortion in Computer Images
Computer images may show distortion
when viewed on the TV, e.g., lines that
should be straight may appear slightly
curved.
Image Resolution
Your Mitsubishi TV can display the resolutions shown in the chart from standard
VGA (640 x 480) through 1920 x 1080
signals at a refresh rate of 60 Hz.
In most cases, the computer will select
the best resolution match to display on
the TV. You can override this setting if you
wish. Refer to your computer operating
system’s instructions for information on
changing the screen resolution.
Original Format
Standard
XGA
1024 X 768
PC 720p
1280 X 720
WXGA
1360 X 768
SXGA
1280 X 1024
Original Format
PC 1080p
1920 X 1080
You may need to restart the computer for
changes to take effect.
For assistance call 1(800) 332-2119
Standard
Zoom
2
21
TV Connections
Before You Begin
Auto Input Sensing
Surround Sound
The TV’s Auto Input Sensing feature automatically recognizes many connections and prompts you to identify
the type of device connected. See page 15 for more on
Auto Input Sensing.
•
Connection Types
Use the connection types available on your input
devices that will give the best video quality. For
example, choose HDMI over component video; choose
component video over composite video.
Picture Quality
For best picture quality, route signals directly from the
source device to the TV whenever possible.
•
To use the surround sound capabilities of the TV’s
speaker array, you must connect the digital surround sound source to the TV on either
-- An HDMI input
-- The ANT antenna input
For best surround sound audio quality from an
external sound system, route audio-carrying cables
from the source device directly to your sound
system.
IMPORTANT
Accessory items such as cables, adapters,
splitters, or combiners required for TV
connections are not supplied with the TV. These
items are available at most electronics stores.
Connection Types and Audio/Video Quality
VIDEO QUALITY
BEST
HDMI
HDMI-to-DVI
BEST
GOOD
Component
Video
Composite
Video
HDMI
AUDIO QUALITY
Digital
Audio
GOOD
Stereo
L/R Analog
Mini-Plug
Audio
For assistance call 1(800) 332-2119
22
2. TV Connections
Inputs and Outputs
DIGITAL 11
Audio
OUTPUT
(page 27)
12
CENTER-CH 14
INPUT
(page 28)
6
AVR/surround
OUTPUT
(page 27, page 41)
13 SUBWOOFER
OUTPUT
(page 28)
NetC OUT/IR IN
(265 Series) NetCommand/
IR external controller jack.
See page 61)
7
1 ANT
coaxial antenna
input
(page 26)
LAN
(Ethernet, port
page 42)
Calibration Microphone Input
(265 series, page 40)
5
AUDIO
analog stereo
audio input
3
Y/VIDEO composite video input
(page 26)
4
Y/VIDEO Pb Pr
component video
input (page 25)
8 USB (page 35)
USB (Power Only)
9 Provides power to
TV accessories.
(page 28)
10 DVI/PC AUDIO
INPUT
(page 25)
2 HDMI
(page 24)
5
AUDIO
analog stereo
audio input
Y/VIDEO Pb Pr 4
component
video input
(page 25)
3
Y/VIDEO
2
composite video
(page 26)
HDMI
(page 24)
Cable Routing
Press the release tab to
loosen the cable bundle.
Installing the cable
tie
1
Install the supplied
cable ties in any of four
mounting holes.
2
Removing the
cable tie
For assistance call 1(800) 332-2119
Sample cable routing. Secure the cable
bundle with the release tab facing out.
2. TV Connections
23
Inputs and Outputs, continued
1. ANT (Antenna)
Connect your main antenna or direct cable service
(without a cable box) to ANT. The ANT input can
receive digital and analog over-the-air channels from
a VHF/UHF antenna or non-scrambled digital/analog
cable source.
2. HDMI® Inputs (High-Definition
Multimedia Interface)
The HDMI inputs support uncompressed standard and
high-definition digital video formats, bitstream Dolby
Digital 5.1, and PCM digital stereo audio.
Mitsubishi recommends you use high-speed HDMI
cables to connect newer source devices incorporating
HDMI technology. High-speed cables bring you the full
benefits of Deep Color and x.v.Color.
These HDMI inputs can also accept digital DVI video
signals. To connect a device’s DVI output to the TV’s
HDMI input, use an HDMI-to-DVI adapter or cable plus
an analog audio. Connect the audio cable to the DVI/PC
AUDIO INPUT jack on the TV to receive audio from your
DVI device.
Use the HDMI inputs to connect to CEA-861 HDMI compliant devices such as a high-definition receiver or DVD
player. These inputs support 480i, 480p, 720p, 1080i,
and 1080p video formats.
3. Y/Video (Composite Video)
Use the adjacent AUDIO R and L inputs if you wish to
send audio to the TV.
4. Y/VIDEO Pb Pr (Component Video)
Use the adjacent AUDIO R and L jacks if you wish to
send audio to the TV.
5. AUDIO
Analog stereo inputs for use in conjunction with adjacent composite or component video jacks.
6. NetC Out/IR IN
265 Series
As an output: Connect IR emitters to this jack to send
NetCommand control signals to external IR-controlled
devices.
As an input: Accepts control signals from an external
controller when set up by your professional installer.
7. LAN
Use the LAN Ethernet jack for streaming internet video
to the TV. See page 42 for setup. Visit www.VUDU.com
for details about VUDU™ service.
8. USB
The TV’s HDMI inputs are compatible with many DVI-D
and HDMI computer video signals.
The TV can read JPEG photo files and mp3 music files
from a USB storage device connected to this input.
These inputs are HDCP (High-Bandwidth Digital Copy
Protection) compliant.
154 Series. Connect a compatible wireless adapter to
stream internet content to the TV (page 42).
9. USB (Power Only)
HDMI Cable Categories
HDMI cables are available as Standard and
High-Speed types.
• High-Speed HDMI Cables. Newer DVD
players, video games, and set-top boxes require
High-Speed HDMI cables, suitable for clock
frequencies up to 340 MHz or data rates of up
to 10.2 gigabits per second. Use high-speed
cables for 1080p HD signals carrying extended
color encodings (i.e., 30 or more bits, also called
Deep Color). High-Speed HDMI cables are also
suitable for standard HDTV signals.
• Standard HDMI Cables. Standard HDMI
cables may be unmarked. They are suitable for
standard HDTV 720p, 1080i, and 1080p signals
with 8-bit color depth. Use Standard HDMI
cables for clock frequencies up to 74.25 MHz or
data rates of up to 2.23 gigabits per second.
Standard USB 5-volt, 500-milliamp power output you
can use to supply power to an accessory device, such
as a wireless subwoofer (page 28).
10. DVI/PC INPUT AUDIO
Connect a DVI device to one of the TV’s HDMI inputs
and use this jack to send analog audio to the TV.
11. DIGITAL AUDIO OUTPUT
This output sends Dolby Digital or PCM digital audio to
your digital A/V surround sound receiver. Incoming analog
audio is converted by the TV to PCM digital audio. If you
have a digital A/V receiver, in most cases this is the only
audio connection needed between the TV and your A/V
receiver.
For assistance call 1(800) 332-2119
24
2. TV Connections
Inputs and Outputs, continued
12. AVR/SURROUND OUTPUT
•
•
Sends analog audio of the current program to an
analog A/V surround sound receiver or stereo
system. Digital audio from digital channels and
HDMI devices is converted to analog audio by the
TV for output on this jack. This is the only audio
connection needed to the TV if using an analog A/V
receiver or stereo system.
Note: If connecting headphones, set Sound >
Global > Analog Audio Out to Variable.
For a fuller surround sound effect, connect external rear speakers to this output to supplement the
TV’s speaker array. Set Sound > Global > Analog
Audio Out to Rear.
HDMI Device
Commonly used with an HDTV Cable Box,
Satellite Receiver, or DVD/Blu-ray Player
Required: HDMI-to-HDMI cable.
Connect an HDMI cable from the TV to the device’s
HDMI output. HDMI-connectable devices provide
video and audio through a single cable.
Mitsubishi recommends using high-speed HDMI cables
to connect newer devices incorporating HDMI technology. See “HDMI Cable Categories” on the previous
page for more on HDMI cable types.
Note: The HDMI connection supports copy protection
(HDCP).
13. SUBWOOFER OUTPUT
Connect a powered subwoofer to this input to complement effects from the TV’s speaker array. Set Sound >
Global > Subwoofer to On to enable this output.
14. CENTER CH INPUT
Connect your A/V receiver’s center channel output to
this input to make the TV speakers output center-channel sound. Set Sound > Global > Center Channel
to On to enable this input. See Sound > Audio > TV
Speakers > Center page 49.
Auto Input Sensing
The TV’s Auto Input Sensing feature automatically recognizes some connections and prompts you to identify the
device type. See page 15.
For assistance call 1(800) 332-2119
HDMI-to-HDMI
cable
Any HDMI device
TV
IMPORTANT
HDMI and Digital Surround Sound
Use an HDMI connection if you want to hear digital
surround sound from the TV’s internal speaker array.
The TV’s HDMI inputs can receive digital surround
sound from an HDMI device.
25
2. TV Connections
DVI Video Device
Y Pb Pr Component Video Device
Commonly used with a Cable Box, Satellite
Receiver, or DVD Player
Commonly used with an HDTV Cable Box,
Satellite Receiver, or DVD/Blu-ray Player
If your source device has an HDMI output, use the connections for HDMI devices described on the opposite
page instead of component video.
Required:
RCA-type component video cables
Left/right analog audio cables.
Note: To hear digital surround sound from an A/V receiver, connect the digital audio output from the device
directly to your digital A/V receiver.
Component
video device
Connect a DVI device (digital only) to one of the TV’s
HDMI input jacks.
Required:
Analog stereo audio cables
DVI-to-HDMI cable or DVI/HDMI adapter and HDMI
cable
If you are using a DVI/HDMI adapter, it is important to
connect the adapter to the DVI device for best performance.
Some devices require connection to an analog input
first in order to view on-screen menus and to select DVI
as the ouput. Please review your equipment instructions for DVI connectivity and compatibility.
Note: The HDMI connection supports copy protection
(HDCP).
Audio
cables
L
R
AUDIO
Y
Pb
Component
video cables
Digital DVI
device
Pr
CABLE IN or
SATELLITE IN
Incoming from
cable service or
satellite dish
AUDIO
OUT
TV
TV
Audio cable
DVI OUT
DVI-to-HDMI
cable
For assistance call 1(800) 332-2119
26
2. TV Connections
Antenna or Cable TV Service
Connect the incoming cable to the TV’s ANT input.
Antenna
or
Direct cable (no cable box)
Cable TV
service
or
IN
ANT
OUT
VCR or DVD Recorder to an
Antenna or Wall Outlet Cable
Required:
1. Video cables
1a. Component video cables (red/blue/green)
or
1b. Composite video cable (usually yellow)
2. Left/right analog audio cables.
3. Two-way RF splitter
4. Two coaxial cables
Note:
Older cable
box
•
Not recommeded. Other connection types
provide better quality audio and video.
•
Use composite video only if component
video or HDMI are unavailable.
If your recording device has an analog-only
tuner, you must use a digital converter box
to enable recording of digital broadcasts.
Composite Video Device
VCR or other device with composite video
output
Required:
Composite video cable (usually yellow)
Analog stereo audio cables.
TV
2.
L
R
AUDIO OUT
COMPOSITE
VIDEO OUT
Composite
video cable
or
1b.
1a.
Audio
cables
Composite
video cable
VCR or other device with
composite video output
L
R
AUDIO OUT
COMPOSITE
VIDEO OUT
COMPONENT
VIDEO OUT
ANTENNA
IN
DVD Recorder or VCR
Incoming cable
Pr
For assistance call 1(800) 332-2119
3.
RF Splitter
4.
4.
27
2. TV Connections
A/V Receiver
A/V Receiver with HDMI Output
Most setups require either a digital audio cable or
analog stereo audio cables. To send audio from TV
channels received on the ANT input or devices connected directly to the TV, you must use one of the connections shown below.
The TV makes all audio available in digital and analog
formats:
• Analog audio coming into the TV is available as
output in digital stereo format on the DIGITAL
AUDIO OUTPUT jack.
• Digital incoming audio is available as analog output
on the AVR/SURROUND OUTPUT L and R jacks.
Optical cable
(digital A/V
receiver)
or
Required: One HDMI-to-HDMI cable
This option allows you to view content from devices
connected to an A/V receiver. The A/V receiver can
send audio and video to the TV over a single HDMI
cable. You can use an HDMI connection as described
here in addition to an audio connection from the TV’s
audio output. The optional audio connection allows you
to hear, through the A/V receiver, devices connected to
the TV only, e.g., an antenna on the ANT input.
• You may be able to use the TV’s remote control
(in TV mode) to operate connected CEC-enabled
HDMI devices. Experiment with your equipment to
determine which functions are available to the TV’s
remote control. See Appendix C, page 81.
• 265 Series: This setup allows you to use NetCommand-controlled audio and video switching over the
HDMI cable. See “Automatic Audio/Video Switching Over an HDMI Connection” on page 69.
• 265 Series: To use NetCommand to supplement
HDMI control of a CEC-enabled A/V receiver, note
the recommendations under “More About Using an
HDMI Connection,” page 69.
Stereo analog cables
(analog A/V receiver)
L
TV
OPTICAL
INPUT
COAXIAL
INPUT
Optional
analog or
digital audio
connection
HDMI cable
A/V receiver back panel
Note:
•
•
On rare occasions, an HDMI signal may be
copy-restricted and cannot be output from
the TV as a digital signal. To hear these copyprotected signals through the A/V receiver, use
the connection for an analog A/V receiver.
Check the A/V receiver’s Owner’s Guide for
information concerning use of the digital input
and switching between digital sound and
analog stereo sound from the TV.
A/V receiver with
HDMI output
HDMI OUT
OPTICAL
AUDIO IN
Any connection
types
High-definition
DVD player
R
L
ANALOG AUDIO IN
VCR
DVD player
Cable box
For assistance call 1(800) 332-2119
28
2. TV Connections
Supplemental Audio Connections
Adding a Subwoofer
Using the TV Speakers as a Center Channel
Add a subwoofer to complement the TV speakers with a
fuller bass sound.
If using an external surround sound system, you can make
the TV’s speakers provide center channel sound. Your
A/V receiver must have a center channel pre out that can
supply an amplified center-channel signal to the TV.
1. Connect your A/V receiver’s HDMI output and center
channel pre out to the TV as shown.
•
After connecting a subwoofer, you must enable the
TV’s subwoofer output in the TV’s Sound menu. Go
to Sound > Global > Subwoofer and set it to On.
•
To control subwoofer volume, press the AUDIO key
and then press to find the subwoofer volume
slider. Press
to change the volume.
HDMI cable
RCA/RCA
audio cable
A/V receiver
with HDMI
output
Subwoofer with Audio Cable
Connect the subwoofer directly to the TV’s SUBWOOFER
OUTPUT.
Surround sound
source device
HDMI OUT
CENTER
CHANNEL
PRE OUT
2. Turn on the A/V receiver’s center channel pre out if
needed. See the A/V receiver’s instruction manual.
3. Press the VOL key to adjust TV volume to about level 30.
4. Enable the TV’s center channel mode:
Wireless Subwoofer
a. Go to Sound > Global and set Center Channel
to On.
Mitsubishi recommends Polk Audio Wireless Subwoofer
model PSW i8m. The transmitter module can be
conveniently powered from the TV’s USB power port.
Connect an audio cable to the transmitter to supply
audio from the TV’s SUBWOOFER OUTPUT.
Power-only
USB port
5.
USB/USB
mini-plug
power cable
RCA/RCA
audio cable
Polk Audio PSW i8m
powered wireless
subwoofer
For assistance call 1(800) 332-2119
b. Press the AUDIO key and press to display the
TV Speakers option. Press
to select Center.
To balance volume:
a. Power on the A/V receiver and TV.
b. Compare the volume of the TV’s center channel
with the rest of the sound system. If the TV
volume needs adjustment,
i. Turn on the TV speakers. Press AUDIO and
press to display the TV Speakers option.
Press
to select On.
ii. Adjust TV volume using the VOL key.
iii. Return the TV to center channel mode. Press
AUDIO and press to display the TV Speakers option. Press
to select Center.
iv. Compare the sound volume. Repeat this
adjustment if needed.
3
29
TV Features
Sleep Timer
The Sleep Timer turns the TV off after the length of time
you set. To set the TV to turn on at a certain time of
day, see the Setup > Timer menu on page 52.
Setting the Sleep Timer
FAV (Favorite Channels)
The FAV key gives you quick access to favorite program
sources. Sources can be channels from the ANT input
or devices connected to the TV. You can store up to
nine favorites.
1. Press SLEEP.
2. Press SLEEP additional times to increase the time in
Adding
1. Press INPUT and switch the TV to the input
you want to add. If adding a channel, switch
to the ANT input and tune to the channel.
2. Press the FAV key.
3. Move the highlight to the number position
you want to assign to the channel or input.
4. Press ENTER.
Removing
Viewing or Changing the Sleep Timer
1. Press SLEEP to display the on-screen message.
2. Press SLEEP additional times to change the time
before the TV powers off. To cancel the Sleep
Timer, press SLEEP repeatedly until OFF is displayed.
Sample Favorites menu. Switch to favorite channels or
inputs using number keys.
1. While watching TV, press the FAV key.
2. In the Favorites menu, highlight the channel
or input you want to remove.
3. Press CANCEL.
Selecting
3.
30-minute increments up to the maximum of 120
minutes.
Press EXIT to clear the screen immediately. Otherwise the screen will clear after five seconds of
inactivity.
1. While watching TV, press the FAV key.
2. Move the highlight to the item you want and
press ENTER. For a shortcut, just press the
number key for the channel or input.
For assistance call 1(800) 332-2119
30
3. TV Features
ChannelView Channel Listings
ChannelView displays program descriptions sent by
broadcasters. This information may be unavailable
in some areas.
ChannelView Custom Channel Banks
About ChannelView
ChannelView™ shows memorized channels on the ANT
input. It displays channel names and program information
for digital channels. No program information is displayed
for analog channels.
ChannelView allows you to set up three banks of custom
channels for convenient access. You can save groups of
channels by content (e.g., news, sports, children’s programming) or by TV user.
Note: You must first set the TV Clock (page 52) to
receive ChannelView listings.
Select a channel bank to customize.
1. Press GUIDE to display ChannelView.
2. Press MENU to move the highlight to the bank
header.
3. Press
to select Bank 1, 2, or 3.
4. With the bank name highlighted, press ENTER to
5.
enter setup mode where you can select channels to
include in the bank.
Press EXIT when finished with setup.
Task
Action
Move between banks
Press
Move into the channel list Press
Add or delete a channel
from the bank
•
ChannelView, “All” tab. Programs are listed on the right.
•
Using ChannelView Listings
Task
Action
Display/hide
ChannelView listings
(ANT input only).
Press GUIDE.
Move through channels
one by one.
Press
Move through channels
quickly.
Press CH.
•
Jump to listings for a
specific channel.
Enter the channel number.
Press CANCEL to add a dash;
press twice to clear the
channel number.
•
Tune to a highlighted
channel.
Press ENTER.
Update program information for a highlighted
digital channel.
Press the INFO key (the
screen may briefly go
blank).
or
.
Display more program
Press INFO.
description for the current
channel (if available).
For assistance call 1(800) 332-2119
.
Highlight the channel
and press ENTER. A
check indicates the
channel has been
added.
Press ENTER again to
clear the check and
remove the channel.
Remove all channels
from the selected bank
Press CANCEL.
Enter or exit setup mode
Press MENU.
Using Custom Channel Banks
•
Display program descrip- 1. Press to move into
tions, if available. The
the program area.
description will appear at 2. Press
to move
the bottom of the screen.
between programs.
.
While watching TV, press CH. The TV will tune only
to channels stored in the current bank.
To change to a different channel bank:
1. Press GUIDE.
2. Press MENU.
3. Press
.
4. Press EXIT.
To allow tuning to any channel in memory, select
the All bank.
31
3. TV Features
Status Display
3
Press the INFO key to see
the on-screen status
display. The most
common displays are
shown here.
4
6
1
402-101 KABC
Monday Night Football
2
TV-PG DLSV
St. Louis vs. Tampa Bay, played in Tampa for
5
8
9
10
INFO
7
Sleep 30 min
13
Tuesday 9:10 PM
HD 1080i Standard
Sample information from the
on-screen status display
English
Surround
11
12
14
1. Current Input
2. Audio Indicator. Key:
About Channel Numbers
TV speakers
External sound system
Mute
Channel Numbers for Over-the-Air
Reception or Reception by Direct
Cable
3. Channel number (antenna source only)
Digital channel includes major and sub-channel numbers.
Note: All signals are automatically
converted to 1080p for display.
5.
Standard-Definition Analog Channels
6. Program name (if broadcast); digital source only
Cable Reception
Channel 3
Cable
3
4. Digital channel name (if broadcast); antenna source only.
V-Chip rating
• Antenna source only for digital signal
• Antenna or VIDEO composite jack for analog signal
7. Program description (if broadcast); digital source, antenna
only. Press the INFO key additional times to see more of the
description.
8. Sleep Timer remaining time
480i Stretch
9. Day and time
Receiving Standard-Definition
Analog Signal (480i)
Standard-Definition Digital Channels
Main Channel 7
Sub-Channel 1
Over-the-Air
Antenna Reception
Ant
7-1 KABC-SD
11. Screen format in use
12. Program audio indicator (antenna source only)
13. Available language (digital source, antenna only)
14. Signal-strength indicator (digital source, antenna only)
Signal Definitions
SD 4:3 Stretch
Receiving Standard-Definition
Digital Signal (SD)
High-Definition Digital Channels
Main Channel 7
Sub-Channel 1
Over-the-Air
Antenna Reception
Ant
10. Signal type being received. See “Signal Definitions” on this
page.
7-1 KABC-HD
HD 16:9 Stretch
Receiving High-Definition
Digital Signal (HD)
480i: Standard-definition, older type interlaced signals from the ANT input,
composite VIDEO, component Y Pb Pr, or HDMI jacks.
480p: Standard-definition progressive-scan DVD signals on component
Y Pb Pr or HDMI jacks.
720p and 1080i: High-definition signals received through component Y Pb
Pr or HDMI jacks. These signals are always 16:9 (widescreen).
1080p: High-definition signals from a PC or Blu-ray player; HDMI inputs only.
SD 4:3: Standard-definition squarish-screen-format signals from digital
channels on the ANT input.
SD 16:9: Standard-definition widescreen-format signals from digital channels on the ANT input.
HD 16:9: High-definition 16:9 widescreen signals from digital channels on
the ANT input.
For assistance call 1(800) 332-2119
32
3. TV Features
Using an External Sound System
Redirecting Audio Output
Controlling A/V Receiver Sound Volume
Selecting the Audio Output
Use one of the methods below to control sound volume from
an A/V receiver.
1. Press AUDIO.
2. Press to show the TV
With a Standard TV Setup
3.
Speakers option.
Press to select either On (to
hear sound from the TV speakers) or Off (to hear sound from
an external sound system).
Choose Center if using the
TV speakers to supplement
audio from an external sound
system. See page 28.
Disconnecting an A/V Receiver
When you disconnect an A/V receiver, change the TV
Speakers setting to On to hear sound from the TV
speakers. Use either the remote control’s AUDIO key or
the Sound > Audio > TV Speakers menu.
•
•
•
Recommended Method: Program the TV’s
remote control for your A/V receiver and enable the
Audio Lock feature. See page 74.
Program the TV’s remote control for your A/V
receiver and set the control mode to AUDIO. Return
the control mode to TV to control the TV.
Use the remote control that came with the A/V
receiver.
With HDMI Control (CEC-Enabled HDMI A/V
Receiver)
The TV’s remote control may control some functions of
the A/V receiver. See Appendix C, “HDMI Control of
CEC Devices,” page 81.
With NetCommand IR Control
265 Series. Set up NetCommand control of the A/V
receiver’s volume functions in the Inputs > AVR menu.
The TV’s remote will then control A/V receiver volume.
See page 68.
For assistance call 1(800) 332-2119
3. TV Features
33
Picture Shape and Display Formats
Format Definitions
Note: See page 18 for use of the FORMAT key to apply
the formats described here.
Standard: The full-screen format used by HDTV signals.
Use this format to display anamorphic DVDs with a 1.78:1
or 1.85:1 aspect ratio. Anamorphic DVDs with a 2.35:1
aspect ratio are displayed correctly but with top and
bottom black bars. Squarish (4:3) images are stretched
evenly from side to side. Available for all signals.
Expand: Enlarges the picture to fill the screen by cropping the top and bottom; useful for reducing the letter box
top and bottom bars of non-anamorphic DVD images.
Effect of Mitsubishi Formats on Picture Types
Zoom: Enlarges the picture to fill the screen by cropping
the sides, top, and bottom to eliminate black bars.
• 480i/480p and SD 4:3 signals: Eliminates top and
bottom bars on anamorphic DVDs with a 2.35:1
aspect ratio.
• 720p, 1080i, SD 16:9, and HD signals: Eliminates
bars added to squarish 4:3 images.
Stretch: Stretches a squarish 4:3 image across the
screen to display the entire image with less distortion
than the Standard format.
Stretch Plus: Similar to Stretch, but minimizes distortion
on the sides by expanding the picture to crop off portions
of the top and bottom. Use
to adjust the vertical
position of the picture.
Original
Signal
TV
Display
Format
Non-anamorphic or SD 4:3
Anamorphic DVD
Standard
Distorted; Not
recommended.
Expand
Recommended
for letterbox. See
Note 1.
Distorted; not recommended. See Note 1.
Zoom
Distorted; Not
recommended.
See Note 1.
Recommended for
anamorphic 2.35:1
images. See Note 1.
Stretch
Recommended
for standard
broadcasts. See
Note 1.
Distorted; not recommended. See Note 1.
Stretch
Plus
Recommended
for standard
broadcasts. See
Note 1.
Distorted; not recommended. See Note 1.
Narrow
See Note 1
Distorted; not recommended. See Note 1.
Recommended
Note 1: Available for 480i, 480p, and digital SD 4:3 signals only.
Original Signal
Display Formats
SD 16:9 or
HD Digital
720p, 1080i,
1080p Signal
Wide Recommended to reExpand move side bars.
(except 720p
)
Full
Best for computer or
Native game images (component and HDMI only)
Zoom
Narrow: Displays narrow 4:3 images in their original shape. Adds black side bars to fill the screen.
Wide Expand: Enlarges the picture, cropping the
image on both sides. Removes or reduces black
side bars added to narrow images converted to
16:9 signals for digital broadcast.
Note: All high-definition channels send widescreen (16:9) signals, but not all programming was
created for the widescreen format. The broadcaster may stretch the image or add side bars to
fill the widescreen area.
Full Native: Displays all pixels in the original image
DVD Image Definitions
Image information may be stated on the DVD
case. Some DVDs support both formats
described below.
Anamorphic (or Enhanced for WideScreen TV)
Indicates DVDs recorded to show widescreen
images properly on 16:9 TV sets using the TV’s
Standard format mode (recommended).
Non-Anamorphic (or 4:3, 1.33:1, Letter Box, or
Full Screen)
Indicates DVDs recorded for viewing on squarish TV screens. They may be full screen (4:3 or
1.33:1) which crops movies to fit the narrow TV, or
letter box, which adds black top and bottom bars.
Recommended to remove bars from the top,
bottom, and sides.
TV Display Formats. Press the FORMAT key repeatedly to see
different displays for the current program. Press the INFO key to
see the name of the format in use.
For assistance call 1(800) 332-2119
34
3. TV Features
Camera Images and Music Files
•
•
•
•
The TV can read photo and music files from a
USB device. Photos must be in JPEG format and
music files must be in mp3 format. To play music
files while displaying a photo slide show, see “USB
Media Setup Menu” on the opposite page.
The TV can display still images or motion video
from a camera through the Y/VIDEO port. See page
36.
To play music through the TV speakers from an
audio-only device, see “Using an Audio-Only
Device,” page 36.
164 and 265 Series. The TV can play music wirelessly using Bluetooth® technology.
USB Source Devices
The USB Media Player Menu
USB Media menu, Photos option selected
Displaying the Menu
1. Back up the data on your USB drive before connecting it to the TV. Mitsubishi is not responsible
for any file damage or data loss.
2. Connect your USB drive to the TV’s USB port.
The USB Media Player menu displays while files
are being read. Wait until icons appear in the menu
before continuing.
3. When the USB Media Player icons display, highlight one of these choices and press ENTER.
Photos
View photos or play a slide show
Audio
Listen to audio tracks or a playlist.
Setup
Perform setup for a slide show or playlist.
If music and image files are both present,
lets you play a slide show with music.
Notes on Using the USB Port
• The TV ignores all commands while reading files.
• Large files or high-capacity storage devices may take a
long time to display.
• The TV can read files up to 10 MB in size with a
maximum of 2,500 files stored on the device. The
FAT16 or FAT32 file system is recommended.
• Use a USB drive instead of a card reader.
• Back up the data on your USB drive before connecting it to the TV. Mitsubishi is not responsible
for any file damage or data loss.
Note: Some manufacturers’ devices may be incompatible with the TV. If the TV is unable to display
your photos, you can:
• Transfer files to a different USB device.
• Use your digital camera’s composite video
output. See page 36.
Picture Files Compatible with the USB Port
• Still images recorded on digital cameras using the
Exchangeable Image File Format, version 2.1 (EXIF
2.1) standard for digital still cameras and Design
Rules for Camera File Systems version 1.0 (DCF 1.0)
• Some images opened and resaved on a computer
may not play back or may not display in the thumbnail list. This happens if the files were resaved in an
incompatible format.
•
Full path file names can be no longer than 50 characters and must end in a .jpg extension. Only the
first 20 of the 50 characters will display.
The TV can read JPEG files as created by the
camera. If you edit a picture file on a computer
and resave the image, the TV may be unable to
read the resaved file.
For assistance call 1(800) 332-2119
3. TV Features
35
Camera Images and Music Files, continued
Using the Photos and Audio
Menus
Use these keys with your photo and audio files.
Key
Use the USB Media Setup menu to set up play of a
slide show or playlist.
For Photos or Audio Tracks
•
•
or
ENTER
USB Media Setup Menu
Moves the highlight left/right through
icons to select Photos, Audio, or
Setup.
Moves the highlight from item to item.
Plays the slide show or playlist starting
from the highlighted item.
Pauses a slide show or playlist.
Stops a slide show or playlist.
•
•
•
•
GUIDE
Highlights the first or last item on the
current page.
Skips to the previous or next item
during play.
Displays the previous or next page of
items.
Skips immediately to the previous or
next item during play.
Rotates an image clockwise in 90˚ increments.
INFO
Displays the item name during play. Press
EXIT to clear.
EXIT
Clears file information from the screen.
MENU
Displays the main menu; stops play.
INPUT
Displays the Input Selection menu; stops
play.
•
•
•
•
•
If JPEG image files and mp3 files are both on the
USB device, choose from:
-- Slideshow + Music
-- Slideshow only
-- Music only
Interval. Select the type of time interval for display
of each slide. The intervals may be longer for larger
files than for smaller ones.
Frequency. Select the number of times (frequency)
to play the complete slide show and/or playlist.
Show File Names. Choose Automatic or Off.
Press EXIT to close the USB Media Setup menu and
return to the USB Media Player menu.
IMPORTANT
Always stop playback with
(STOP) or change to
a different TV input before disconnecting your USB
device.
For assistance call 1(800) 332-2119
36
3. TV Features
Camera Images and Music Files, continued
Photos and Motion Video as Composite
Video
Connect the camera to the TV using a composite video
cable and control the slide show or movie through the
camera. The display resolution will be standard-definition (480i).
1. Refer to the owner’s manual supplied with the
camera for instructions needed for this setup.
2. Set the camera’s output signal type to NTSC and
3.
put the camera into playback mode.
With the camera still turned on, connect your digital
camera’s composite video cable (usually yellow) to
the TV’s Y/VIDEO jack. To hear audio, connect the
camera’s audio output cable to the AUDIO L jack.
Optional
Audio Cable
TV
Using an Audio-Only Device
To use the TV speakers with an audio device such as an
MP3 or CD player with analog output, follow these steps.
1. Insert an unused RCA-style connector into the
Y/VIDEO jack associated with the TV’s analog audio
input. The presence of this connector activates the
TV’s auto-detection.
2. When the TV detects the Y/VIDEO connector, it will
display the New Device Found screen. Name the
new input CD/Audio or MP3 Player.
3. Connect left (white) and right (red) audio cables from
AUDIO OUT on the device to AUDIO L and R on the TV.
4. Keep the connector in the VIDEO/Y jack while using
the audio-only device.
Audio-only
device
TV
2.
Unused
RCA-style plug
(plug in first)
1.
Camera connection using a composite video cable
4. When the New Device Found screen displays,
assign the name Camcorder.
5. Press EXIT to close the New Device Found screen.
6. Highlight the icon for the camera input and press
ENTER.
7. If viewing photos, control the slideshow from the
camera. Advance through the images manually or
check if the camera can advance automatically.
For assistance call 1(800) 332-2119
AU
C
V
3. TV Features
37
Camera Images and Music Files, continued
Wireless Audio Playback
164 and 265 Series. The TV’s built-in speaker
array can play audio from a handheld device using
Bluetooth® A2DP (stereo audio) wireless technology.
Tips for Wireless Playback
Note: Make sure the TV is on any input other than
the USB port before starting Bluetooth pairing.
Press the INPUT key to change.
•
Pairing the TV with an Audio Playback Device
1. Turn on the wireless device you wish to use for play2.
back. Turn off all other wireless devices in the area
as the TV can pair with only one device at a time.
Press INPUT to display the Input Selection menu.
•
•
•
•
Selecting the Bluetooth icon at a later time will
connect the TV again to the paired device.
If the paired device is not available, the TV will
accept pairing from a different device.
Once connection is lost, the TV will power off after
five minutes without receiving a signal.
To clear a paired device, turn off the Bluetooth icon
(Inputs > Name menu) or pair the TV with a different device.
To remove the Bluetooth icon from the Input
Selection menu, turn off the icon in the Inputs >
Name menu.
Bluetooth icon in Input
Selection Menu
3. Highlight the Bluetooth icon and press ENTER.
4. Pair your device with the TV and then connect. Some
5.
devices pair and connect automatically, while others
require you to enter the TV pass code displayed.
Use keys on the TV’s remote control to control playback. Not all keys work for all devices.
Skip a track
Remove the Bluetooth icon from the Input Selection
menu by turning off Bluetooth in the Input > Name
menu.
(Pause)
(Stop)
(Reverse)
(Play)
(Forward)
Resetting Bluetooth Pairing or Connection
Perform this reset if the audio device does not connect
properly to the TV.
1. If the audio device has been previously paired with
2.
3.
4.
5.
the TV, delete the TV from the device’s paired list.
Go to the TV’s Inputs > Name menu and highlight
the Bluetooth icon. Press ENTER to select Off.
Press EXIT.
Go to the Inputs > Name menu and highlight the
Bluetooth icon. Press ENTER to select On.
Press EXIT.
For assistance call 1(800) 332-2119
38
3. TV Features
Sound Projector
This setup is unnecessary if using the TV speakers
as a center channel. See page 28.
Sound Projector Technology
The TV’s built-in speaker array can be adjusted to
reflect sound off the room walls to create a surround
sound effect. Setup can be performed either manually
or automatically.
• To create the surround sound effect, the room walls
must reflect sound and not be covered with soundabsorbent material.
• Repeat the setup procedure if you reconfigure the
room’s walls or furnishings.
Connecting the TV
To hear digital surround sound, the TV must be connected to a digital surround sound source. The TV can
receive digital surround sound from:
• Any HDMI jack
• The ANT input (from some digital broadcasts)
Other stereo connections will provide Dolby Pro Logic
surround sound.
Basic Manual Setup
Before You Begin
Note: 265 Series. If you have already performed Auto
setup, do not make manual adjustments. Doing
so will erase all settings created during Auto
setup.
Positioning the TV
1. Press MENU and go to Sound > SoundPro.
•
•
Center the seating area in front of the TV and at
least six feet away from it.
Arrangements that give good results:
2. Enter the room dimensions and layout information
requested in the screen. To change measurements, press
or enter numbers on the remote
control’s keypad.
•
If the room is an odd shape, locate the TV to take
best advantage of wall reflections.
3. Press EXIT to exit and save settings.
4. Play some sample audio to check sound quality.
If further adjustment is needed, use the Custom
menu as described next.
•
Avoid locations that may distort sound reflections.
Custom Menu
Use the Custom menu after defining the room layout.
For a room with large areas of curtains that might affect
sound reflection, do the following:
a. Open the curtains fully to improve sound reflection.
b. Set angles by performing the procedure in
“Adjusting Beam Angles.”
c. Close the curtains.
d. Set levels by performing the procedure in
“Adjusting Levels.”
For assistance call 1(800) 332-2119
3. TV Features
39
Sound Projector, continued
1. From the Sound > SoundPro menu go to the
CUSTOM menu.
How to Make Adjustments in the Custom Menu
• Press
to select an audio beam; colors of the
adjusters correspond to audio beams in the onscreen diagram.
• Press
to redirect the audio beam or change
the sound level.
2. Position yourself in your usual viewing location.
Remain in this position, looking at the TV, while
making the following adjustments.
3. Adjusting Beam Angles
a. Adjust Center Beam Angle until sound is
about equal in both ears.
b. Adjust Left Beam Angle to maximize sound
heard from the front left side.
c. Adjust Right Beam Angle to maximize sound
heard from the front right side.
d. Adjust Left Surround Beam Angle to where
the sound seems to come from the left rear
side. If this cannot be achieved, make the
setting the same as that for Left Beam Angle.
e. Adjust Right Surround Beam Angle to where
the sound seems to come from the right rear
side. If this cannot be achieved, make the
setting the same as that for Right Beam Angle.
Controls in the SoundPro
> Custom menu adjust the
direction and focus of the TV’s sound output.
At extreme beam angles, adjustment may be
limited and the image on screen may not accurately
represent the sound beams.
4. Adjusting Levels
a. Adjust Center Level to the mid level.
b. Adjust the following levels one at a time so that
each one sounds about the same as the center
level:
Left Level
Right Level
Left Surround Level
Right Surround Level
c. Check all sound levels by quickly switching
between them using
.
d. Readjust individual levels in small increments
and recheck as above until all sound levels
seem about the same.
5. Adjusting an External Subwoofer
Note: Set Sound > Global > Subwoofer to On to
make this adjustment available.
a. Play sample video or music containing lowfrequency bass sound.
b. Press AUDIO. Use
to display the Subwoofer option.
c. Press
to adjust the subwoofer volume.
Adjust the volume level of individual audio beams
using sliders in the SoundPro > Custom menu.
Resetting Angle and Level Values in the Custom
Menu
Follow these steps to return settings to the default
values.
1. Press EXIT to clear all menus.
2. Press MENU. Go to the Sound > SoundPro menu
and press ENTER.
3. Change any setting (e.g., TV Location).
4. Press EXIT to clear all menus.
5. Press MENU. Go to the Sound > SoundPro menu
6.
7.
and press ENTER.
Enter the correct values for the room layout.
Return to the CUSTOM menu to adjust angles
and levels.
For assistance call 1(800) 332-2119
40
3. TV Features
Sound Projector, continued
Auto Setup
265 Series
Auto setup uses the included calibration microphone to
optimize Sound Projector performance for most room
conditions.
Initial Preparation
1. Position and connect the TV as described under
2.
3.
“Before You Begin,” page 38.
Power on the TV and external subwoofer, if any.
Plug the microphone cable into the TV’s INPUT 3
left audio jack.
Microphone Placement
• Make sure there are no large obstacles between
the TV and microphone.
• Place the microphone
-- On a flat, level surface at least six feet away
from the front of the TV.
-- On a tripod or on the backrest of your seating.
-- At the same height yours ears would be when
watching TV. The height must be within 3
vertical feet of the height of the TV’s speaker
array.
-- Centered in front of the TV, not off to the side.
TV
6 ft. minimum
4. Place the microphone as described in the guidelines on this page.
Start Auto Setup
5. Press MENU and go to Sound > AutoSP.
Maximum height above speakers
Height of TV
speakers
6. Highlight START and press ENTER.
7. Quietly exit the room right away. The calibration
8.
9.
sequence will start in a few seconds and may be
loud. It is important to leave the room as your presence will interfere with the calibration process.
Wait for completion of setup before returning to the room.
Play some sample audio material to check the
sound quality.
Note: Do not perform manual adjustments after running Auto setup, as this will erase all settings
defined during Auto setup.
10.Store the microphone out of direct sunlight and
away from heat.
For assistance call 1(800) 332-2119
Microphone
Set the microphone
on a level surface at
ear height at least
six feet from the TV.
Use a seat backrest
or tripod so as to
pick up sound from
all directions.
3 ft.
Be sure the
height of the
microphone is
within three feet
of the speaker
height.
Microphone
Center the microphone in front of
the TV.
41
3. TV Features
Sound Projector, continued
External Rear Speakers
You may wish to supplement surround sound from the
TV with external rear speakers. External speakers can
fill in rear sound if your room lacks a rear wall suitable for reflecting sound. The addition of wireless rear
speakers is a convenient way to enhance rear sound.
Mitsubishi recommends Polk Audio’s F/X Wireless Surround system.
Transmitter
TV
Transmitter
To left and right
audio inputs
Connecting the transmitter to the TV
Polk Audio F/X
Wireless Surround
speaker unit
6. Play sample audio to check the sound. Repeat any
of the adjustments as needed.
Sample room layout without a back wall suitable for rear
sound reflections
1. Position the external speakers as needed for rear
sound.
2. Connect analog audio output from the TV to the
3.
4.
Polk Audio F/X Wireless Surround transmitter.
Power on the TV, speakers, and transmitter.
Set Sound > Global > Analog Audio Out to Rear.
Sound Projector adjustments when using external rear
speakers.
5. Adjust the sound output. Go to the Sound >
SoundPro > CUSTOM menu. Review the instructions in “Custom Menu,” page 38.
a. Adjust beam angles for the left, right, and
center beams. Because the external speakers
output left and right surround beams and they
do not appear in the adjustment image.
b. Adjust volume levels for all audio beams.,
including the left and right surround beams.
For assistance call 1(800) 332-2119
42
3. TV Features
StreamTV™ Internet Media
Internet services provided by VUDU™ Apps let you
access many popular on-line applications. In addition
to free content, VUDU’s movie service lets you buy
and rent movies through the TV. Visit www.VUDU.com
to learn more about available movie titles, prices, and
services offered. For a list of recommended routers
and switches, see the Support > FAQ section at VUDU.
com.
Note: From time to time you may notice changes to
the internet interface as new features are added.
Required for StreamTV internet media:
• Broadband internet service (at least 2 Mbps for SD,
4 Mbps for HD, and 8 Mbps for 1080p HDX)
• Ethernet cable or to connect a 154 series TV wirelessly, an AzureWave AW-NU231 USB wireless
adapter.
• Computer access to the VUDU.com website
(required for initial account activation).
• A credit card for rental and purchase transactions
from VUDU’s movie service.
Home Network Setup
Manual
Before using StreamTV internet media, you must
connect the TV to the internet using one of these
methods.
Note: Manual setup is available only for a wired connection.
1. Connect the TV to your network router with a
Category-5 Ethernet cable (not supplied).
2. In the Setup > Network menu, highlight Manual
and press ENTER.
3. Press to move to the Connection Data area.
4. Input the connection data.
5. After entering connection data, press ENTER to
connect.
6. Change any of the following if needed:
• Default Gateway
• DNS
• Subnet Mask
Note: Make sure the TV is on any input other than the
USB port. Press the INPUT key to change.
Ethernet Connection
DHCP (automatic)
1. Connect the TV to your network router with a
Category-5 Ethernet cable (not supplied).
Router or modem
providing high-speed
internet service
Incoming
internet
cable
Ethernet
cable
LAN
2. Open the Setup > Network menu to review settings.
Setup > Network, DHCP connection
3. Press EXIT to clear the menu.
For assistance call 1(800) 332-2119
3. TV Features
43
StreamTV™ Internet Media, continued
4. Highlight the desired network and press ENTER to
Wireless Connection
•
•
164 and 265 series models have built-in wireless
capabilities and can communicate directly with your
wireless router.
154 series TVs require an AzureWave AW-NU231
USB wireless adapter.
connect. A check will appear next to the connected
network. Press CH/PAGE to see more networks if the
list fills more than one screen.
1. Disconnect the Ethernet cable if present.
2. For a 154 series TV, connect the USB wireless
adapter.
Incoming
internet
cable
Setup > Network menu after connecting. The active
network is checked and connection data displays.
5. If connecting to a secure network, enter the
IEEE 802.11n-compliant
wireless network router
providing high-speed
internet service
network key or password when prompted. Special
remote control keys you may need:
USB wireless
adapter
154 Series TV. A USB wireless adapter is required for
wireless connection.
3. Open the Setup > Network menu. After a few
Key
Use for
1
Digit 1 and special characters
! @ # $ % ^ * _ - + = . space ?
CANCEL
moments, detected networks will appear listed on
the screen in order of signal strength.
•
•
LAST
Clears the password box of an old
entry from a prior session.
Deletes one character during password entry.
Toggles between upper and lower case
6. Press ENTER to connect.
Note: If you notice interference from the TV’s internal
wireless components, turn off the TV’s transmitter. Open the Setup > Network menu. Select
Off and press ENTER.
To reconnect later, open the Setup > Network
menu, highlight the network, and press ENTER.
Setup > Network menu, manual connection
For assistance call 1(800) 332-2119
44
3. TV Features
StreamTV™ Internet Media, continued
Using StreamTV Internet Media
1. After establishing internet connectivity as described
2.
3.
Troubleshooting
If You Are Unable to Connect to the Internet
• Check all power and data connections.
• If you can reach the internet with a computer or
other device on the same internet service used by
the TV, consult the router or modem owner’s guide
for reset instructions.
• If you cannot reach the internet, contact your
service provider. You may be asked for network
information such as the TV’s IP address. Go to the
Setup > Network menu to see connection data.
in “Home Network Setup,” page 42, switch the TV to
any input other than Bluetooth® or USB.
Press the INTERNET key to display services from
VUDU Apps.
Press ENTER to launch an application.
Getting Started with VUDU Movies
1. After establishing internet connectivity as described
2.
3.
4.
5.
in “Home Network Setup,” page 42, switch the TV to
any input other than Bluetooth® or USB.
Press the INTERNET key to display services from
VUDU Apps.
Select the VUDU movie service.
Browse the VUDU movie catalog and offerings.
When you are ready to rent or buy a movie, you
will be prompted to activate your VUDU account.
Follow the on-screen instructions and use a computer to go to www.VUDU.com/activation. A
credit card is required for activation.
For Further Assistance
• If you are having trouble connecting your TV or
accessing internet applications, contact Mitsubishi
Customer Care at 1-800-332-2119.
• If you are having difficulty with your VUDU
account, contact VUDU Customer Care at
www.VUDU.com/support.
• See more troubleshooting tips in Appendix E.
Once your account is activated, you can rent and buy
movies using only the TV and the TV’s remote control.
Using VUDU Apps and VUDU Movies
TOOLS. Use the Tools menu to perform A/V reset
while in VUDU movies or some VUDU Apps.
Navigate VUDU’s menus with the keys on
the TV’s remote control. Browse the movie
catalog, watch movie previews, set parental
controls, and rent or buy movies.
LAST
• Goes to the previous screen.
• Stops video playback and returns to the previous menu.
CANCEL. Acts like the backspace key during
text entry.
LAST
ENTER
• Selects a menu item.
• Launches an application from the VUDU
Apps menu.
• In VUDU’s movie service, use during
video playback to see options.
•
•
Directional navigation
In VUDU Apps, press
more applications.
to display
GUIDE. In VUDU’s movie service, returns to
the VUDU home menu.
TOOLS
INTERNET
CH/PAGE. Jumps to the previous or next page of
menu items.
INTERNET. Displays the VUDU Apps internet
menu. Switch the TV to any input other than
Bluetooth® or USB before connecting to the internet.
EXIT. Depending on context:
• Closes the internet menu.
• Goes to the VUDU home page.
In VUDU’s movie service:
PLAY/PAUSE
Starts or pauses video playback.
INFO. In VUDU’s movie service, works like
the VUDU MORE key. Displays more options
for the current selection if available.
FAST FORWARD/REVERSE
• Press to search scenes forward or back.
• Press additional times to speed up search.
• Press opposite key to slow and pause search.
F2. Displays the VUDU system menu if available.
STOP
Stops video playback and returns to the previous menu.
For assistance call 1(800) 332-2119
45
3. TV Features
Introduction to Home-Theater Control
This TV offers a choice of home-theater-control systems. This summary offers some examples of the control
methods available using the TV’s remote control. You may wish to use one or more of these methods in your
home theater after completing Auto Input Sensing.
Source device connected directly to the TV
Remote Control Programming (Any Connection Type)
Program the remote control to operate the A/V device. To control the device, set
the remote control to the correct mode for the device type. See Appendix A, “Programming the Remote Control.” In the case of an A/V receiver, use the Audio Lock
feature, page 74.
Any Connection Type
A/V
Device
TV
HDMI
Cable
CEC-Enabled HDMI Device (HDMI Connection Only)
See Appendix C, “HDMI Control of CEC Devices,” page 81.
CEC-Enabled
A/V Device
265 Series. NetCommand IR Control (Any Connection Type)
Set up NetCommand IR control of the device’s keys as desired. See “IR Emitters,”
page 61, and “Initial NetCommand Setup,” page 62.
TV
Any Connection Type
A/V
Device
TV
Source device connected to an A/V receiver connected to the TV
CEC-Enabled
Source Device
CEC-Enabled HDMI A/V Receiver
The TV’s remote control may operate some functions of a connected A/V device.
You can switch to the device by selecting its icon in the TV’s Input Selection menu.
See Appendix C, “HDMI Control of CEC Devices,” page 81.
HDMI
Cable
A/V Receiver
TV
265 Series: A/V Receiver with HDMI Output (no CEC)
1. Set up NetCommand IR control of the A/V receiver’s keys as desired. See “IR
Emitters,” page 61, and “Setting Up A/V Receiver Control,” page 68.
2. Set up NetCommand IR control of the source device’s keys as desired. See
“NetCommand Control of a Device Connected to an HDMI A/V Receiver,” page
71.
Source
Device
HDMI
Cable
Any Connection Type
A/V Receiver
HDMI
Cable
TV
For assistance call 1(800) 332-2119
46
4
TV Menus
Main Menu
Press MENU on the remote control to open the main menu.
Picture
Picture settings.
46
Sound
Sound settings.
49
Captions
Closed captions
on/and off; caption
displays.
51
Setup
Basic TV setup.
52
Inputs
Name assignments for TV
inputs, HDMI Control setup
265 Series. NetCommand
IR “learning.”
55
Lock
Setting a pass code and
restrictions TV use. Disabling the control-panel
buttons.
57
Picture
Assign a name to the TV input before making video adjustments (use the New Device Found or Inputs > Name
menu). Adjustments will be reset to the defaults if you
rename the input after making adjustments.
Picture
Video
Settings in this menu are saved for the current input only.
To make Video adjustments while watching TV and without using the menu:
1. Press the VIDEO key.
2. Press
to select a video option.
3. Press
to change the setting.
Picture
Mode
Brilliant
For use under bright light; unavailable when the
current input is named Game or PC.
Game
Optimizes picture and video processing for gaming
consoles. Available only when the name of the
input is Game or PC.
Bright
For most daytime viewing and x.v.Color sources
Natural
For most nighttime viewing and x.v.Color sources
Special
Advanced Modes. Contact your professional installer for setup or see page 48.
164 series: Special/ADV
265 series: ISF Day/ADV1, ISF Night/ADV2
ISF Day,
ISF Night
For assistance call 1(800) 332-2119
Set the Picture Mode first
before changing other video
settings, as some settings are
stored independently for each
Picture Mode. Use Picture
Modes to get the best image
under different viewing conditions.
4. TV Menus
47
Picture, continued
Contrast
•
•
•
Brightness
Color
Tint
Sharpness
Color Temp
Low contrast shows a variety of shades in darker images
In most home lighting situations, medium contrast looks
best.
High contrast shows darker images more uniformly black
and makes colors appear more vibrant. High contrast is
good for brightly lit environments.
Adjusts the white-to-black level
Settings are stored independently for each Picture Mode.
Adjusts overall picture brightness. Settings are stored independently for each Picture Mode.
Adjusts overall color intensity from monochromatic to fully saturated.
Adjusts the red-to-green ratio.
Adjusts picture detail and clarity.
High
Gives white images a cool cast. May provide the most
realistic picture under bright lighting.
Low
Gives white images a warm cast. Natural/Color
Temp at the low setting displays video at approximately the 6500K industry standard for NTSC
pictures.
High,
Medium,
Low, Off
•
•
•
•
EdgeEnhance
(164, 265 series)
On, Off
EdgeEnhance™ adds special edge enhancements to make the image appear
sharper.
DeepField
Imager
(164, 265 series)
On, Off
DeepField™ Imager dynamically enhances black levels in portions of the screen to
provide strong contrast with detail over mixed screen content.
Demo
For comparison, displays a split picture to show On (right side) and Off (left side).
Video
Noise
Backlight
Picture
Screensaver
Film Mode
High. For poor-quality signals.
Medium. For moderate noise reduction.
Low. For good-quality signals.
Off. Leaves the picture unaltered.
Adjusts the white balance.
Settings are stored independently for each Picture Mode.
Reduces minor noise (graininess) in the picture.
Adjusts peak brightness of the backlight. Applies uniformly to all inputs. Press ENTER to turn the
backlight on or off.
Picture+ (Picture Plus)
On, Off
Select On to display a screensaver pattern while playing an audio-only input. To
use this feature, the input must either
• Be named as an audio source (e.g., CD, MP3 Player, Bluetooth)
or
• Be the antenna input tuned to an audio-only signal.
Auto, Off
480i and 1080i signals only. In Auto, the TV automatically detects and applies
film-decoding correction to movies filmed at 24 frames per second. Try the Off
setting if images show many jagged edges. Setting saved by input.
For assistance call 1(800) 332-2119
48
4. TV Menus
Picture, continued
True 120 Hz
(154, 164 series)
True 240 Hz
(265 series)
When active, reduces motion blur in action scenes but may show pixel
structure during slower motion or in still images. Works in conjunction
with Film Mode. The adjustment side of the screen only shows changes
if the content was a film source shot at 24 frames per second.
Test Picture
Displays a test picture.
Picture
Reset
•
•
Picture
Press
to make adjustments.
Resets sound and picture adjustments for the current input. Highlight the Reset icon
and press ENTER twice to perform reset.
Reset has no effect on universal settings (Balance, Listen To, Language) or on
Advanced picture settings.
Perfect
(PerfectColor, 265 series)
PerfectColor Sliders Adjusts the saturation (intensity) of six colors for the current image source.
PerfecTint Sliders Adjusts six hues for the current image source
Using PerfectColor:
Highlight the Perfect icon and press ENTER to display the PerfectColor menu. Settings are retained independently
for each TV input.
Using PerfecTint:
• To switch between PerfectColor™ and PerfecTint™ adjustments, highlight PerfectColor/PerfecTint and press
.
• Press
to move from one color bar to the next.
• Press
to change settings.
• Press CANCEL to restore default settings.
• Press MENU to return to the main menu.
Picture
Advanced (164 and 265 series)
Picture > Advanced allows you to save highly customized picture adjustments for each input. Mitsubishi recommends these adjustments be
made only by a trained professional installer.
1. Press MENU. Under Picture, highlight the Advanced icon and press ENTER.
2. With Picture Mode (the first option) highlighted, press ENTER to change from blank (undefined) to ADV.
265 Series: Choose ADV1 (daytime settings) or ADV2 (nighttime settings).
3. Use
to highlight an option you wish to change and press ENTER to see the adjustment display.
4. Press
to change settings.
5. Use
to navigate to additional options and press
to change settings.
6. Press MENU to return to the Picture > Advanced menu and save the adjustments for the current input. Press EXIT
to close the menu..
To use the custom Picture Mode at a later time
Press MENU and go to Picture > Video > Picture Mode and:
For assistance call 1(800) 332-2119
4. TV Menus
49
Picture, continued
164 Series
•
•
265 Series
Select SPECIAL if settings were saved by your
professional installer.
Otherwise select ADV.
•
•
Select ISF Day or ISF Night if settings were saved by
your professional installer.
Otherwise select ADV1 or ADV2.
To return to the default values for Advanced
Display the Picture > Advanced menu and:
164 Series
265 Series
Highlight RESET Pic Mode and press ENTER.
1. Highlight the Advanced mode to change.
2. Highlight RESET Pic Mode and press ENTER. You must
perform the reset separately for both ADV1 and ADV2
Note: Custom ISF Day and ISF Night settings made by
your professional installer are locked for protection
and cannot be reset by this method.
Sound
Sound
Audio
Settings in this menu are saved for the current input only with the exception of Balance and Subwoofer, which apply
to all inputs.
To make Audio adjustments while watching TV and without using the menu:
1. Press the AUDIO key.
2. Press
to select an audio option.
3. Press
to change the setting.
TV Speakers
Bass
Treble
Balance
Subwoofer
On
Turns on the internal TV speakers.
Off
Turns off the internal TV speakers so you hear sound only from a connected A/V receiver.
Note: When you disconnect an A/V receiver, be sure to change the Sound setting
to TV to hear sound from the TV speakers.
Center
Makes the TV’s speaker array act as a center channel. See “Using the TV Speakers
as a Center Channel,” page 28.
Notes:
• Set Sound > Global > Center Channel to On to make this setting available.
• To de-activate the center channel, change this setting to On or Off.
Controls volume of low-pitched sound from the TV speakers.
Controls volume of high-pitched sound from the TV speakers.
Controls audio balance between the right and left TV speakers
[Subwoofer level Adjusts the volume level of a connected subwoofer.
adjustment]
Note: Set Sound > Global > Subwoofer to On to make this adjustment available.
For assistance call 1(800) 332-2119
50
4. TV Menus
Sound, continued
Sound Mode
Stereo
No special audio effects from the TV speakers
Surround
Modifies audio from the TV speakers.
• For monaural (non-stereo) programs, creates a simulated stereo effect.
• For stereo programs, creates a simulated surround sound effect.
• The TV’s speaker array plays surround sound if available.
Music
Optimizes the TV’s speaker array for music listening.
Night
Focuses the TV’s speaker array to a single point to limit sound heard by others
outside the room. Press ENTER to adjust the focal point (Night Angle).
Level Sound
On, Off
Reduces differences in sound volume between programming segments, such as the
difference between regular broadcast programs and commercial segments.
Listen To
(applies only
to analog
channels from
the ANT input)
Stereo
The TV plays stereo broadcasts in stereo and mono broadcasts in mono. The word
Stereo is displayed when you tune to a channel broadcasting in stereo.
Mono
Reduces background noise. Use when receiving a weak stereo audio signal. All
audio is played as mono.
Sound
SAP
Selects an additional monaural sound track not audible during normal TV viewing.
(Second Audio The SAP signal might be related to the program (such as a sound track in a foreign
Program)
language), or it might be unrelated (such as a weather report). If an SAP signal is
broadcast, the letters SAP are displayed when you tune to the channel.
Global
Settings in this menu apply to all inputs.
Analog Audio
Out
Subwoofer
Center Channel
Sound
These settings affect audio from the AVR/SURROUND OUTPUT jacks.
Fixed
Use with an analog A/V receiver. Control volume from the A/V receiver. The
volume of the audio output signal is fixed and is unaffected by the TV’s volume
control.
Variable
Use with headphones. Adjust headphone volume using the TV’s volume controls.
When set to Variable, the audio output signal is adjustable from the TV’s volume
controls.
Rear
Sends left and right rear audio to external speakers. Use when supplementing the
TV’s speaker array with external rear speakers. See “External Rear Speakers,” page 41.
Select On to turn on audio to a connected subwoofer. Set to Off if no subwoofer is connected.
On allows the TV’s speakers to complement your external sound system as a center channel. Set
to Off if not in use.
Auto SP
265 Series. Performs auto calibration of the Sound Projector speaker array. See “Auto
Setup,” page 40.
Sound
SoundPro
Lets you set up the Sound Projector speaker array manually. See page 38.
For assistance call 1(800) 332-2119
4. TV Menus
51
Captions
Captions on Digital Channels
•
The TV can decode captions from the ANT input only.
Broadcasters can send up to six different captioning
selections or can send analog captions for a program
that originated in analog format. A TV station may broadcast only one or two types of captions or none at all.
•
Captions on Analog Channels
The TV can decode captions from the ANT input and
the composite VIDEO jacks. Broadcasters can send
either standard closed captions or text service. Standard
closed captions follow the dialogue of the program and
display in a small section of the screen. Text-service closed
captions often contain information such as weather or
news and cover a large portion of the screen.
Captions
•
IMPORTANT
Analog text-service options display a large
black or gray box on the screen when no
caption signal is being broadcast.
The content of captions is determined by the
broadcaster. If captions show strange characters, misspellings, or odd grammar, it is not
a malfunction of the TV.
Closed-caption signals are not available through
HDMI or component jacks. See the menus for
devices connected to these inputs for closedcaption decoding.
Services
Service
On if Mute, On, Off
On if Mute: Displays digital closed-caption signal Caption 1 (digital) or CC1
(analog) when audio from the TV speakers is muted. While watching TV,
press MUTE to turn closed captions on/off.
Digital
Caption 1–Caption 6
Caption signals sent by the broadcaster.
Analog
CC 1–CC 4
Text 1–Text 4
•
•
Captions
CC 1–CC 4. Standard closed-caption signals
Text 1–Text 4. Text-service signals
Font
Style
As Broadcast or
choice of font styles
(digital captions only)
As Broadcast changes settings to those selected by the captions provider,
or, if none, to the TV’s own caption defaults. Use one of the font styles to
give digital captions a custom appearance.
Size
Large, Medium, Small
Large is recommended.
Captions
Font
Color
White, Black, Magenta, etc.
Recommendations for digital captions:
Translucent, Opaque, Flashing, Transparent
•
Background
White, Black, Magenta, etc.
•
Opacity
(Background)
Translucent, Opaque, Flashing, Transparent
Opacity
A white font on a black translucent background makes an easy-to-read combination.
Use contrasting colors for captions and background.
For assistance call 1(800) 332-2119
52
4. TV Menus
Setup
Setup
Menu
Antenna
Digital
Audio
Setup
Language
English
Spanish
Displays on-screen menus in either English or Spanish.
Selects the current language for a digital program from the ANT input. Each digital program may
include up to seven language choices or there may be no language choice offered.
Clock
Set the TV clock to:
• Use the TV Timer to power on the TV automatically at a preset time
• Receive correct updates to ChannelView listings
Note: When the Daylight Saving Time change occurs, you must open this menu and set the TV’s clock ahead or back.
Time
Date
Time
Zone
Daylight
Savings
Setup
•
•
•
Highlight the Clock icon and press ENTER or to highlight the time. To edit time and date:
• Press ENTER to select the item to change.
• Press
to change values. Press ENTER to confirm entries.
• Press
to move to another column.
Eastern, Central, Mountain, Pacific, etc. The correct time zone is required for accurate ChannelView
updates.
Off, On
Timer
Select the setting for your area (required for accurate ChannelView updates).
The Timer tells the TV to power on automatically at a time you set. Use this menu to set a day,
time, input, and channel for the Timer. If the TV is already on at the set time, the TV will automatically change to the designated channel or input.
The TV clock must be set before you can use the Timer feature.
As a reminder that the TV Timer is set, the TV POWER indicator flashes slowly while the TV is powered off.
When the Timer turns on the TV, press any key on the remote control to keep it from turning off after five minutes.
Timer
Day
Time
Device
On, Off
Select On to enable the Timer.
Daily, Mon-Fri, (every) Sunday, (every) Monday, Select the day or days of the week for the Timer to
(every) Tuesday, etc.
turn on the TV.
To set the time for the TV to come on:
1. Highlighted the time and press ENTER.
2. Press
to change values. Press ENTER to confirm entries.
Ant, DVD, VCR, etc.
Select the input you want displayed when the TV comes on. Choose from the defined and enabled
inputs that appear in the Input Selection menu.
Channel If the source is the ANT input, press
For assistance call 1(800) 332-2119
to select a channel number or press and hold to scroll quickly.
53
4. TV Menus
Setup, continued
Setup
Channel
Ant Air,
Ant Cable
All Channels,
New Only
Scan
You must perform a channel scan to receive digital channels. The scan searches for broadcast channels and adds them to TV memory. To start channel scan:
1. Highlight one of the input selections based on your connection to the ANT input:
• Air when connected to an indoor or outdoor antenna.
• Cable when connected to direct cable (no cable box)
2. Select the scan type.
• Select All Channels for an initial scan or after moving the TV to an new area with a different channel line-up.
• Select New Only to search for channels newly broadcasting since the previous scan.
3. Press to highlight SCAN.
4. Press ENTER to start channel memorization.
See below for additional notes on Scan.
Edit
After channel scan, Edit lets you add and delete memorized channels. Memorized channels are
those you can tune using the CH key. Edit the channel list to limit tuning to channels you watch.
• Press CH/PAGE to jump to the next or previous page of channel numbers.
• Press
to move through all channel numbers, one at a time.
Adding/Deleting Channels Using the Channel Edit Menu
•
•
•
•
Channels marked with a check are in memory.
To add or delete a channel from memory, highlight
the channel number and press ENTER.
To add a single digital channel not in the list, see the
notes under Scan on this page.
Digital channels are listed by virtual channel number
with the physical channel number shown in small
gray text.
-- Virtual Channel Number (digital channels only).
A channel number sent by a local broadcaster.
Notes on Scan and Channel Memorization
• Channel memorization may take up to 15 minutes to
complete.
• To stop channel memorization before completion, press
CANCEL. Channels already added are retained.
• When watching TV, press CH to move through
memorized channels. Press and hold CH to speed
through channels.
• To add a digital channel that does not appear in the
Edit menu without performing channel memorization:
1. Look up the physical channel number for
the new digital channel. See the website
www.antennaweb.org for help.
2. Press INPUT and select the Ant input.
--
Physical Digital Channel Number. The
channel number officially assigned to the actual
broadcast frequency; shown on screen in gray
text.
3. Use the number and CANCEL keys to enter the
physical channel number followed by “-1” and
ENTER. For example, for physical channel 36,
3
•
6
1
ENTER.
The TV will search for a digital channel on the channel 36
frequency. When it finds the channel, it will:
a. Add the channel to memory.
b. Change the channel number to the virtual
channel number sent by the broadcaster.
c. Add to memory any associated sub-channels.
Rememorize channels if you move the TV to a different
geographic area with a different channel line-up.
For assistance call 1(800) 332-2119
54
4. TV Menus
Setup, continued
Setup
Energy
Blue Glow. (265 series). Select On to see blue accent lighting when the TV is powered
on.
Setup
Network
See “Home Network Setup” on page 42 for use of this menu.
Ethernet Connection DHCP (automatic), Manual
[Connection Data]
Wireless Connection [Network ID]
[Connection Data]
Off. Turns off the radio receiver. Use this option if there is RF interference with other
devices.
For assistance call 1(800) 332-2119
4. TV Menus
55
Inputs
Inputs
Name
INPUT and HDMI jacks:
Cable box, Cam(corder), CD,
DVD (DVD, DVD2, Blu-ray), DVR,
Game (Game, PS, Xbox, Wii),
Media Box, PC, Satellite, AVR
On/Off (Ant, Bluetooth only)
INPUT jacks only:
CD/Audio, MP3 Player, VCR
HDMI jacks only:
PC, AVR, Delete
•
•
•
•
•
Lets you assign or change names of inputs appearing in the Input Selection menu. Highlight an input and press ENTER multiple times to cycle
through the name choices.
Lets you turn the Ant and Bluetooth inputs On/Off to display or hide them
in the Input Selection menu; highlight the input and press ENTER to switch
between On and Off. A paired device is cleared from memory when the
Bluetooth icon is turned off.
Lets you delete unused HDMI inputs from the Input Selection menu.
A CEC-enabled tuner can be named either Cable Box or Satellite.
A CEC-enabled DVD player can be named DVD, DVD2, or Blu-ray.
General Notes for the Inputs > Name Menu
When you change an input name and then exit the
Name menu:
• The name is changed
• The icon in the Input Selection menu is changed
• Audio and video settings are changed to the
defaults for the new device type.
• 265 Series: All previous NetCommand IR “learning” for the input is erased.
Notes for HDMI devices
• Disconnecting an HDMI device: When you disconnect an HDMI device, the icon remains in the Input
Selection menu until you remove it. Select Delete in
the Inputs > Name menu to remove an unwanted icon
for an HDMI input.
Inputs
•
•
•
If the New Device Found screen does not display
as expected when you connect an HDMI device,
see “Reactivating Auto Input Sensing for an HDMI
Input,” page 15.
HDMI Control and CEC-Enabled Devices: See
Appendix C, “HDMI Control of CEC Devices,” page
81.
If case of CEC conflicts: Turn off CEC signals in
one of these ways:
-- Turn off the TV’s HDMI Control signals to the
device (Inputs > HDMI Control menu).
-- Turn off each device’s internal CEC capability.
See Appendix C for the TV’s HDMI Control or, to
turn on/off a specific device’s response to CEC
signals, see the device owner’s manual.
Learn 265 Series. Sets up or changes NetCommand IR control of the current device.
See “About NetCommand IR Control,” page 60.
Inputs
Inputs
AVR
265 Series. Sets up or changes NetCommand IR control of an A/V receiver.
See “NetCommand IR Control of an A/V Receiver” on page 67.
HDMI
Control
On, Off
Select On or Off to enable or disable the TV’s control of a CEC-enabled
device. See Appendix C for use of this feature.
For assistance call 1(800) 332-2119
56
4. TV Menus
Inputs, continued
Inputs
Order
Lets you rearrange icons in the Input Selection menu.
1.
2.
3.
4.
Press
to highlight an input icon.
Press ENTER to confirm the selection.
Press
to drag the icon to the desired position.
Press ENTER to confirm the new position.
Inputs
Demo
See demonstrations showcasing selected TV features.
For assistance call 1(800) 332-2119
4. TV Menus
57
Lock
TV Locks
Parental Menu
Parental
Lock by Program Ratings
Restricts access using U.S.-based ratings
sent by broadcasters.
Time
Lock by Time
Restricts TV use by time of day.
Channel
Lock by Channel
Blocks access to the channels you
specify.
Panel
Lock Control Panel
Disables the buttons on the TV’s control
panel. Use this feature if small children
in the home try to press buttons on the
control panel.
Other
Lock by Other Program Ratings
Restricts access using non-U.S.-based
ratings sent by broadcasters.
Pass Code
Setting a Pass Code
You are prompted to enter a pass code whenever you
select Lock on the main menu. To set a pass code for
the first time:
1. Press MENU and highlight Lock. A screen prompting you for a pass code will display.
2. Input a four-digit pass code using the number keys
on the remote control.
• Press CANCEL to delete a number and move
back one space.
• Press MENU or EXIT to close the menu without
setting a pass code.
3. Press ENTER to confirm the pass code.
The TV comes from the factory with the rating locks
turned off and with pre-set U.S. ratings TV-PG and
movie rating PG. You must turn on blocking for U.S.
ratings to activate these rating restrictions. Use the
Lock > Parental menu to change the level of blocking
with U.S. ratings.
Any time you change the channel or device, it may take
up to five seconds for the rating restrictions to take
effect.
Other Menu (Alternate Rating System)
This TV can recognize new rating systems that may
come into effect in the future. The Other menu allows
you to block digital programming when such systems
come into effect. The Start Time and Stop Time
options in the Parental menu apply to U.S.-based
ratings only and do not affect alternate rating systems.
The first time you tune to a channel broadcasting an
alternate rating system, the TV defaults to the most
restrictive setting if the Lock menu > Other Lock
option is set to On. Use this menu to change the
allowed rating if you are unable to watch a program
rated with an alternate system.
Bypassing TV Locks
•
•
Resetting a Pass Code
See the procedure in Appendix B.
•
•
•
If you try to watch a blocked program or channel
or the TV is locked by time, a notice will appear
prompting you for a pass code. To use the TV,
input your four-digit pass code and press ENTER.
-- To reactivate the locks after using a pass code,
power the TV off and then on.
-- To reactivate only the parent ratings lock,
change to a different channel or device.
If a program is blocked, you can still use the TV
without entering a pass code. Change to a channel
airing an allowed program or change to another
device.
Important Notes on Rating Locks
Parental menu rating locks apply only to channels and signals received on the ANT and composite VIDEO jacks.
Other menu rating locks apply only to digital channels received on ANT.
When viewing a cable box, satellite receiver,
or other device connected to the component
Y Pb Pr or HDMI inputs, check the device’s
owner’s guide for parental locks.
For assistance call 1(800) 332-2119
58
4. TV Menus
Lock, continued
Lock
Parental
Lock
TV Rating
Movie
Rating
Start Time/
Stop Time
Disables or enables blocking based on V-Chip signals and the U.S. rating system.
Highlight the rating level you wish to
change and press ENTER to block it ( ) or
allow it ( ).
You can apply supplemental content
blocking to the age-based ratings by
using the TV content categories. (FV, D,
L, S, V)
Highlight the rating level you wish to change and press ENTER to block it ( ) or allow it ( ). You
can apply supplemental blocking to the age-based ratings by using the TV content categories below.
Sets the time of day for enforcement of rating restrictions chosen in the Parental menu. To make
rating restrictions active 24 hours a day, make Start Time and Stop Time the same.
1. Highlight the start time or stop time.
2. Press ENTER to start editing.
3. Press
to make changes.
4. Press ENTER to confirm changes.
TV Content Categories
TV Age-Based Ratings
TV Program Ratings
TV-Y
Youth. For children under 7.
TV-Y7
Youth 7 and older.
TV-G
General Audience. For the entire family.
TV-PG
Parental Guidance. Parental Guidance
recommended; may not be suitable for
some children.
TV-14
Adolescent 14 and older. Not recommended
for children under 14.
TV-MA
Mature Audience. For adults only.
FV
Fantasy Violence. Applies to TV-Y7 only.
D
Sexual Dialog. Applies in differing
degrees to TV-PG and TV-14.
L
Adult Language. Applies in differing
degrees to TV-PG, TV-14, and TV-MA.
S
Sexual Situations. Applies in differing
degrees to TV-PG, TV-14, and TV-MA.
V
Violence (graphic or realistic). Applies in differing degrees to TV-PG, TV-14, and TV-MA.
For assistance call 1(800) 332-2119
Movie Ratings
G
General Audience. Designed for the
entire family.
PG
Parental Guidance. Parental Guidance
recommended; may not be suitable for
some children.
PG-13
Parental Guidance, 13 and Older.
Not recommended for children under
13.
R
Restricted. Restricted in theaters to 17
years old and older unless accompanied
by an adult.
NC-17
No Children 17 or Under. Restricted
in theaters to 18 years old and older.
X
Adult. Designed for and restricted in
theaters to adult audiences only.
Not
Rated
No MPAA rating assigned
4. TV Menus
59
Lock, continued
Lock
Time
Lock by
Time
Lock Time,
Unlock
Time
Blocks all use of the TV during the time period you specify. You must enter a pass code to
use the TV when the time lock is in effect. After releasing the lock with the pass code, the lock
does not go back into effect until the next time the TV is powered on.
Enables/disables Lock by Time.
To set the lock and unlock times:
1. Highlight the lock or unlock time.
2. Press ENTER to start editing.
3. Press
to make changes.
4. Press ENTER to confirm changes.
Note: To make Lock by Time active 24 hours a day, make Start Time and Stop Time the same.
Lock
Channel
Lock
Panel
Off, On
Lock
The Channel Lock menu lists channels currently in memory (see page 53). Highlight a
channel and press ENTER to lock ( ) or allow ( ) the channel. Channels locks will be
cleared the next time you perform a channel scan.
On locks and Off unlocks the buttons on the TV’s control panel. Use this option if small children try
to press TV buttons.
• To release the Panel Lock from the TV’s control panel, press and hold the INPUT button for ten
seconds. If the TV is powered off, press POWER after the lock releases to make the TV power on.
• To reactivate the lock, return to this menu and change the setting to On.
Other
Other Menu Options (alternate rating system)
This TV can recognize new rating systems that may come into effect in the future. Such alternate rating systems will apply only to digital programming received on the ANT input.
Lock
On, Off
Enables/disables program blocking.
System
The rating system available for the channel
Group
Rating groups available in the rating system shown on the screen. Rating groups are defined by the
rating system in effect.
Rating
Rating restrictions available in the selected rating system and group. Highlight the rating and press
ENTER to check (block) or uncheck (allow) rated content.
For assistance call 1(800) 332-2119
60
5
NetCommand IR Control
About NetCommand IR Control
•
•
•
•
•
NetCommand IR home-theater control is available on 265 series TVs.
IR emitter cables are available for purchase
from Mitsubishi. Visit www.mitsuparts.com or call
800-553-7278 and request one of the following:
-- 242D483020 (two-ended cable)
-- 299P254020 (four-ended cable).
NetCommand setup is optional.
You can perform NetCommand setup for a device
any time after the TV has detected the device.
NetCommand operates by sending remote control
signals from the TV to your other devices via the
For assistance call 1(800) 332-2119
•
IR (infrared) emitters, telling the devices to play,
record, change inputs, adjust volume, change channels, or perform other functions. All this is accomplished with the TV’s remote control left in TV mode.
You may wish to use NetCommand IR control to
supplement control of CEC-enabled devices.
Important Note on NetCommand
Be sure to connect the IR emitter cable to the
TV and properly place the emitters so that
NetCommand can control your devices.
61
5. NetCommand IR Control (265 Series)
*OGSPOUPGBTJOHMF
BWFSBHFTJ[FEEFWJDF
*3TFOTPS
IR Emitters
*3TFOTPS
*3TFOTPS
Placement
The NetCommand system uses emitters connected
to the IR–NetCommand Output jack to control other
devices such as DVD players, cable boxes, satellite
receivers, and VCRs.
IR emitter cables are available for purchase from
Mitsubishi. Request either part number 242D483020
(two-ended cable) or part number 299P254020 (fourOGSPOUPGBended cable).
0OUPQPGBTJOHMFUBMM
6. Place any unusedEFWJDF
ends behind the devices to
prevent stray signals from reaching the IR sensors.
*OGSPOUTIBSFECZUXP
BWFSBHFTJ[FEEFWJDFT
OHMFBWFSBHF
1. Connect the plug end of the IR emitter cable to the
[FEEFWJDF IR—NetCommand Output jack on the TV back panel.
2. When the New Device Found screen displays,
highlight IR—NetCommand Output.
*3TFOTPS
*3TFOTPS
Other A/V Device
TPS
S
CH
D I G I T A L
SURROUND
A/V Receiver
Connecting IR–NetCommand Output
The New Device Found screen displays when you
connect the IR emitter.
OGSPOUTIBSFE
CZUXPBWFSBHF
3. Highlight EXIT and press ENTER.
TJ[FEEFWJDFT
4. Position the emitter end with the emitter bulb facing
the device’s remote control sensor. The bulb emits
infrared light in a cone-shaped pattern. Place the
bulb far enough from the sensor to allow the cone
pattern to reach the sensor.
In some cases, the emitter works better facing
downward from the top of the device. Experiment
to find what works best.
5. Secure the emitter ends in place using double-
*OGSPOUPGBTJOHMF
BWFSBHFTJ[FEEFWJDF
*3TFOTPS
*3TFOTPS
*OGSPOUTIBSFECZ
UXPBWFSBHFTJ[FE
EFWJDFT
*3TFOTPS
*3TFOTPS
Place IR emitters so the signal can be “seen” by the IR
sensor on each device.
If You are Unable to Locate
a Device’s IR Sensor
•
sided tape.
•
IMPORTANT
Position IR emitters so that each device’s
sensor “sees” the signal from only one emitter.
Otherwise, a device receiving signals from
multiple sources (remote controls, IR emitters)
may not respond at all.
0OUPQPGBTJOHMF
UBMMEFWJDF
*3TFOTPS
The IR sensor is usually behind the plastic window
of the front display panel. Using a flashlight, you
may be able to see it as a round or square cutout.
If you cannot see the sensor and the device’s
Owner’s Guide does not specify the location, do
the following using the device’s remote control.
1. Starting at one end of the plastic window, hold
the device’s remote control about one-half
inch from the front of the device and press the
POWER key.
2. If the device does not respond, move the
remote control one inch toward the center and
try again. Repeat until the device responds.
3. Repeat the previous steps starting at the other
end of the window. The sensor is between
these two points.
For assistance call 1(800) 332-2119
62
5. NetCommand IR Control (265 Series)
NetCommand Setup
Initial NetCommand Setup
3. Switch the TV to the desired input to control. Press
To perform this procedure, you need:
• The remote controls for both the TV and the
device you want to control.
• An IR emitter cable available from Mitsubishi.
4.
5. The first function highlighted in the Learn screen
Note: To set up an A/V receiver, see “Setting Up A/V
Receiver Control,” page 68.
1. Connect and position the IR emitters for the
2.
INPUT, highlight the input icon, and press ENTER.
Open the NetCommand Inputs > Learn menu.
6.
devices you wish to control. See “IR Emitters” on
the previous page.
Set the TV’s remote control to TV mode and power
on the TV.
NetCommand and Device-Specific Keys
Device-specific keys are those which have no
equivalent on the TV’s remote control. Use any of
these methods to set up NetCommand control for
these keys.
•
is always Power On. Aim the TV’s remote control
at the TV and press ENTER to begin learning for that
function.
When the Power On text starts flashing, aim the
device’s remote control at the TV and hold the POWER
key until a check mark appears next to Power On.
• If the text stops flashing before the check mark
appears, repeat the previous step.
• To remove the key from NetCommand control,
press the CANCEL key while the key name is
highlighted.
• To verify the device’s response to the IR code,
press ENTER to send out the code.
TOOLS Menu. In some cases, the TV will, by
default, assign a key to the TOOLS menu. See
the table below.
Examples of Default NetCommand
Assignments in the TOOLS Menu
Cable Box, Satellite Receiver
DVD, DVR,
Blu-ray
VCR
A/V Receiver
3
MENU
9
ON DEMAND
3
SETUP
6
TOP MENU
9
ANGLE
3
MENU
6
INPUT
3
MENU
6
SURROUND
NetCommand’s default setup assigns some
device-specific keys to the TOOLS menu when
“learned.” These key functions are accessible only
with the TOOLS key.
•
•
F Keys. There are four F keys, F1 through F4,
which you can assign to any function on the
device’s remote control. For a cable box,
“learn” the F keys as the A, B, C, D keys.
Arbitrary Key Assignment. You can assign a
device key arbitrarily to any “unlearned” key
on the TV’s remote control. Make a note of the
key name and function for later reference.
For assistance call 1(800) 332-2119
Inputs > Learn screen. Key names marked with a check
have been “learned.”
Some device-specific keys, such as MENU, are available
only from the TOOLS menu after “learning.”
7. Use navigation keys on the TV’s remote control to
highlight other keys on the list. Repeat steps 5 and
6 for each additional function you wish to control
through NetCommand.
8. If the device has a separate POWER OFF key, use
9.
navigation keys on the TV’s remote to highlight
Power Off. Repeat the earlier steps to “learn” the
POWER OFF key.
If the device has no POWER OFF key, skip this step.
Press EXIT to finish NetCommand “learning” for the
current device.
5. NetCommand IR Control (265 Series)
NetCommand Setup, continued
Adding or Removing Device Keys from
NetCommand Control
After performing initial setup, you can add or remove
individual keys under NetCommand control.
1. Switch the TV to the device. Press INPUT, highlight
the device’s icon, and press ENTER.
2. Open the Inputs menu and highlight the Learn icon.
3. When the Learn screen displays:
• To add keys: Continue as described earlier
under “Initial NetCommand Setup” on the
opposite page.
• To delete keys: Highlight the name of the key
you wish to delete and press CANCEL on the
TV‘s remote control. Clears the check mark.
63
Operating NetCommand-Controlled
Devices
Controlling Most Device Types
As an example of NetCommand control, if you are
watching your cable box and you wish to tune to the
next channel higher, press CHANNEL Up. NetCommand
then sends the “learned” channel-up control signal to
the cable box.
1. Perform NetCommand setup for the device as
2.
3.
4.
described in this chapter.
When you wish to use the device, press INPUT.
Highlight the icon for the device.
Press ENTER to switch the TV to the device.
Note: if you have set up automatic input switching for
the A/V receiver, the A/V receiver will automatically switch to the correct input for the device.
5. To operate the device using the TV’s remote
control, press the TV key to put the remote control
into TV mode.
6. Point the remote control at the TV (not the device)
and press the key for the desired function.
7. Press the TOOLS key to access additional key functions you may have “learned” for the device.
For assistance call 1(800) 332-2119
64
5. NetCommand IR Control (265 Series)
Operating NetCommand-Controlled Devices, continued
Special Operation Methods
Key Name in
Learning Screen
Special Operation Description and Setup
How to Use
Power On
Manual Power On/Off
Use for devices that have only one POWER key.
1. Press INPUT.
2. Highlight the icon for the device to be
powered on or off.
3. With the Input Selection menu still displayed, press POWER to send the power
signal; you may need to press POWER twice.
Note: If you press POWER without the Input Selection menu displayed, the TV will turn
off.
4. Press ENTER to switch the TV to the device.
Power On
Power Off
Menu
Automatic Power On/Off
This feature is only for devices that have separate
Power On and Power Off keys on their original
remote controls. If your device does not have a
separate Power Off key, do not use the Power
Off learning position; use only the Manual Power
ON/OFF method described above.
In the NetCommand Learn screen:
a. “Learn” the Power On command in the
Power On learning position.
b. “Learn” the Power Off command in the
Power Off learning position.
•
To Power On the Device
1. Press INPUT.
2. Highlight the icon for the device to be
powered on or off.
3. Press ENTER to switch the TV to the
device and NetCommand will send the
Power On command to the device.
•
To Power Off the Device
When you turn the TV off, the TV sends all
learned Power Off commands to all devices.
Displaying a Menu for the Current Device
Press TOOLS and number 3 to send the menu
signal to the device.
“Learn” the MENU key on the original remote in the
Menu learning position.
Guide
Displaying the On-Screen Program Guide
(cable box or satellite receiver)
1. While watching the device, press GUIDE to
display the guide.
1. “Learn” the Guide key on the original remote in 2. Press PAGE to send the Page Up/Dn commands for the guide.
the Guide learning position.
2. Learn the PAGE UP and PAGE DOWN keys of the
original remote in the Page Up and Page
Down learning positions.
Enter
ENTER-Key Functions (cable boxes, satellite receivers, etc.)
Some devices have two keys that have “enter” functions. One key is for menus and is often labelled
SELECT or OK. A second key is for use with number keys for direct channel selection. NetCommand
uses the same ENTER key for both operations.
When ENTER has a menu or guide function or
when the original remote control uses the same
key for menus and channel selection:
Learn the ENTER, SELECT, or OK key in the
NetCommand Enter learning position.
For assistance call 1(800) 332-2119
1. Press MENU or GUIDE to display the device’s
menu or guide.
2. Press ENTER within the menu and
NetCommand will send the Enter signal for
menus.
5. NetCommand IR Control (265 Series)
65
Operating NetCommand-Controlled Devices, continued
Key Name in
Learning Screen
Special Operation Description and Setup
Enter (digits) When ENTER is for channel changes, i.e., the original remote control has a separate ENTER key for
this function):
How to Use
Press digit key(s) and then press ENTER.
NetCommand will send the Enter signal for
channel selection.
Learn the ENTER key for channel selection in
the NetCommand Enter (digits) learning position. Use this learning position only if the original
remote control has separate keys for Enter in
menus and Enter for channel selection.
Cancel
CANCEL as the Cancel or Exit Function
“Learn” the Cancel or Exit function in the
NetCommand Cancel learning position
1. Press MENU or GUIDE to display the menu or
guide.
2. Press CANCEL and NetCommand will send
the Cancel or Exit signal.
—
(separator)
The symbol “—” can serve as the separator
Press digit key(s) and press CANCEL.
between a digital channel’s main and sub-channel NetCommand will send the channel-separator
digits, e.g., digital channel 12-1 (main channel is
signal.
12, sub-channel is 1).
“Learn” the channel separator function in the
NetCommand – (separator) learning position.
For assistance call 1(800) 332-2119
66
5. NetCommand IR Control (265 Series)
Operating NetCommand-Controlled Devices, continued
NetCommand Specialized Device Keys
Refer to this chart when “learning” device keys. “Learn”
some, all, or none of the keys used for each device
type.
See page 64 for more on keys marked in the “Special
Operation Method” column.
Name on TV See Special
Remote
Operation
Control
Method Table
Key Name in
Learning Screen
Function
Power On
Power On or Power ON/OFF (toggle)
Guide
On-Screen Program Guide or DVD Disc Menus
Channel +/Skip +
Next Channel Higher/Skip Forward (Disc)
Channel –/Skip –
Next Channel Lower/Skip Backward (Disc)
Page Up
Page Up in Guides
Page Dn
Page Down in Guides
Last
Last Channel Recall
LAST
Fav
Favorites
FAV
Menu
Menu
Up, Down, Left, Right
Arrow up, arrow down, arrow left, arrow right
Enter
Enter or Select (menus)
Cancel
Cancel or erase (menus)
Info
On-screen status display or information display
Play
Start playback
Stop
Stop playback
Forward
Fast Forward
Rewind
Rewind/Fast Reverse
Pause
Pause playback
Record
Start Recording
1, 2, 3, 4, 5, 6, 7, 8, 9, 0
Digits
Enter (digits)
Use after entering digits to tune to a channel by number
- (separator)
Adds digital channel separator between main channel
number and sub-channel number
F1
F3
F4
Power Off
GUIDE

MENU
,
,
,
ENTER


INFO
Require two
keypresses
1, 2, 3, 4, 5, 6, 7, 8, 9, 0
Assign your
choice of
specialized
functions.
F2

Power Off
For assistance call 1(800) 332-2119
ENTER


F1
F2
F3
F4

6
NetCommand IR Control of an A/V
Receiver
NetCommand IR home-theater control is available on 265 series TVs. See the description of
NetCommand on “About NetCommand IR Control,”
page 60.
Two levels of NetCommand A/V receiver control are
available through the Inputs > AVR menu.
• Power and volume. See the next page.
• Automatic audio and video switching over
HDMI. See “Setup to Control Automatic Audio and
Video Switching via HDMI,” page 70.
Note: To set up control of other device types, see
“Initial NetCommand Setup,” page 62.
Controlling an A/V Receiver
after NetCommand Setup
Switching Audio to and from the A/V
Receiver
1. Press AUDIO.
2. Press to show the TV Speakers option.
3. Press to select either On (sound through TV
speakers) or Off (sound through A/V receiver).
Controlling A/V Receiver Power
With Any Connection Type
1.
2.
3.
4.
Press AUDIO.
Press
to show the TV Speakers option.
Press to select Off.
Point the remote control at the TV (not the A/V
receiver) and press POWER to power the A/V
receiver on or off.
With an HDMI Connection
1. Press INPUT.
2. Highlight the A/V receiver icon.
3. Press POWER.
Controlling Other A/V Receiver Functions
•
•
With the A/V receiver powered on and selected, the
TV’s remote control operates the volume and mute
functions.
If you have performed setup to control A/V receiver
switching over HDMI, when you switch to a device
in the Input Selection menu, the A/V receiver will
automatically switch to the correct audio input for
the device.
Note: Connect the HDMI cable between the TV
and A/V receiver first before performing
NetCommand setup for the A/V receiver. If you
perform NetCommand setup and then later connect the cable, the NetCommand setup will be
lost.
For assistance call 1(800) 332-2119
67
68
6. NetCommand Control of an A/V Receiver (265 Series)
Setting Up A/V Receiver Control
Power and Volume
3. When the Power text starts flashing, aim the A/V
receiver’s remote control at the TV and hold the
POWER or POWER ON key until a check mark appears
next to Power.
• If the text stops flashing before the check mark
appears, repeat this step.
• To remove the key from NetCommand control,
press the CANCEL key while the key name is
highlighted.
Perform this setup to control A/V receiver power and
volume with the TV’s remote control.
To perform this setup you need:
• The remote controls for both the TV and the
A/V receiver.
• An IR emitter cable available from Mitsubishi.
Before You Begin
1. Connect your A/V receiver to the TV and any addi2.
3.
tional devices.
Connect the IR emitter cable to the TV and position
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitters,” page 61.
Set the TV’s remote control to TV mode.
4. Press the
5.
Setup to Control A/V Receiver Power and Volume
1. Open the Inputs > AVR menu.
2. The first function highlighted in the AVR screen is
always Power. Aim the TV’s remote control at the
TV and press ENTER to begin learning for Power.
Inputs > AVR screen. Perform
NetCommand IR “learning” for A/V
receiver power and volume keys.
For assistance call 1(800) 332-2119
6.
key on the TV’s remote control to highlight
other keys in the list. Repeat steps 2 and 3 for each
additional function you wish to control through NetCommand.
If the A/V receiver has a separate POWER OFF key,
press on the TV’s remote to highlight Power
Off. Repeat steps 2 and 3 to “learn” the POWER OFF
key. If the device has no POWER OFF key, skip this
step.
When finished “learning” the power and volume
keys, press EXIT to watch TV or continue
NetCommand setup if using an HDMI connection.
See “Automatic Audio/Video Switching Over an
HDMI Connection” on the opposite page
6. NetCommand Control of an A/V Receiver (265 Series)
69
Setting Up A/V Receiver Control, continued
Automatic Audio/Video Switching Over an
HDMI Connection
If your A/V receiver has an HDMI output, it may be convenient to send audio and video to the TV over a single
HDMI cable through the A/V receiver. The following
setup enables the A/V receiver to switch automatically
to the correct input when you select a device in the TV’s
Input Selection menu. The connected source devices
can be analog, digital, or a mixture or the two.
Connections of
any type
HDMI
Cable
TV
Blu-ray player
Cable box
HDMI
Output
DVD player
VCR
A/V Receiver
Use NetCommand to switch an A/V receiver
automatically to the correct audio and video inputs for
a device (available only with an HDMI output to the TV
as shown).
More About Using an HDMI Connection
• Audio from devices connected directly to the
TV can be heard from the TV speakers only.
To send audio to the A/V receiver from such
devices, use one of the optional audio connections shown in the diagram on the next
page. For example, use an optional audio
connection if you wish to use the A/V receiver
speakers to hear audio from:
-- The ANT input
-- A game or camcorder connected to the
TV.
• To use NetCommand to supplement HDMI
control of a CEC-enabled A/V receiver, the
recommended setup sequence is:
1. Connect the HDMI cable.
2. Enable HDMI control (New Device Found
screen).
3. Connect the secondary digital audio
cable, if desired.
4. Perform NetCommand setup.
If you perform A/V receiver NetCommand
setup first and then later connect an HDMI
cable, the NetCommand setup will be lost.
•
In some cases, audio from a device connected
to the A/V receiver may not be passed over the
HDMI cable to the TV speakers. In these cases
you must use the A/V receiver speakers to hear
audio.
For assistance call 1(800) 332-2119
70
6. NetCommand Control of an A/V Receiver (265 Series)
Setting Up A/V Receiver Control, continued
Before You Begin
To complete these steps you will need:
• The remote controls for both the TV and the
A/V receiver.
• An IR emitter cable available from Mitsubishi.
• An HDMI-to-HDMI cable to connect the A/V
receiver to the TV and cables necessary to
connect devices to the A/V receiver.
4.
5.
1. Connect the A/V receiver to the TV with an HDMI2.
3.
to-HDMI cable. Do not connect the optional audio
cable at this time.
If desired, enable HDMI Control of a CEC-enabled
A/V receiver. See Appendix C, “HDMI Control of
CEC Devices.”
Connect your audio/video devices to the A/V
receiver. Note the name of the device connected
to each A/V receiver input. This information will be
needed later to set up NetCommand’s automatic
input switching.
If using an optional audio cable between the TV
and A/V receiver, connect it. Set up NetCommand
control of the A/V receiver’s TV audio input when
setting up automatic switching in the next procedure.
Connect the IR emitter cable to the TV and position
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitters,” page 61.
Setup to Control Automatic Audio
and Video Switching via HDMI
When this setup is complete, the “learned” A/V receiver
input will appear in the TV’s Input Selection menu as a
selectable input.
1. Set the TV’s remote control to TV mode.
2. Navigate to the Inputs > AVR menu.
TV
Optional
analog or
digital audio
connection
HDMI cable
To set up A/V switching over HDMI, choose your A/V
receiver input from a list.
3. In the Inputs > AVR menu, highlight the name of the
4.
5.
A/V receiver with
HDMI output
HDMI OUT
OPTICAL
AUDIO IN
Any connection
types
High-definition
DVD player
R
L
ANALOG AUDIO IN
6.
VCR
DVD player
Cable box
Multiple video inputs through a single HDMI cable.. The
optional audio connection allows you to hear, through the
A/V receiver, devices connected to the TV only, e.g., an
antenna on the ANT input.
For assistance call 1(800) 332-2119
A/V receiver input to control. In this example, it is
the DVD input.
Press ENTER on the TV’s remote control.
While the text DVD is flashing, press and hold the
DVD INPUT key on the A/V receiver’s remote control.
When a check appears next to DVD, release the
DVD INPUT key.
• If the text stops flashing before the check mark
appears, repeat this step.
• To erase the IR code just “learned,” press
CANCEL while the name is highlighted.
7. If using an optional audio cable between the TV and
A/V receiver, “learn” the TV AUDIO OUT key to enable
automatic switching of audio from sources connected to the TV only.
If there are no more devices to set up, highlight
EXIT and press ENTER or continue to set up additional A/V receiver audio/video sources.
Y/ VIDEO
8.
6. NetCommand Control of an A/V Receiver (265 Series)
71
Setting Up A/V Receiver Control, continued
NetCommand Control of a Device Connected to an HDMI A/V Receiver
Use this setup to have NetCommand control a device
sending audio and video through the A/V receiver to the
TV via HDMI.
You must have already completed the procedure under
“Setup to Control Automatic Audio and Video Switching via HDMI” on the opposite page. That procedure
placed an icon in the Input Selection menu for the
device (input) connected to the A/V receiver.
Any Connection
Type
Source
Device
A/V
Receiver
HDMI
Cable
TV
1. Set up NetCommand control of A/V receiver audio/
2.
3.
4.
5.
6.
7.
video switching via HDMI as described on the
opposite page.
Press EXIT to close any open menus and return to
normal TV viewing.
Press INPUT.
Highlight the icon for the A/V receiver input you
wish to control.
Press ENTER to switch the TV to the A/V receiver
and the A/V receiver to the input.
Open the Inputs > Learn menu.
Perform NetCommand “learning” for the connected )device by following the steps in “Initial
NetCommand Setup,” page 62.
For assistance call 1(800) 332-2119
72
Appendices
Appendix A: Programming the Remote Control. . . . . . . . . . . .
73
Appendix B: Bypassing the Parental Lock. . . . . . . . . . . . . . .
79
Appendix C: HDMI Control of CEC Devices.. . . . . . . . . . . . . .
81
Appendix D: TV Care. . . . . . . . . . . . . . . . . . . . . . . . . . . .
84
Appendix E: Troubleshooting. . . . . . . . . . . . . . . . . . . . . . .
85
For assistance call 1(800) 332-2119
73
Appendices
Appendix A: Programming the Remote Control
This appendix explains programming the TV’s remote
control to operate other A/V devices. This is distinct
from NetCommand or HDMI CEC.
Functions Available for Other A/V Devices
The TV’s remote control can be programmed to operate
other types and brands of A/V products. The functions performed in each device mode vary depending
on the product. Not all functions work for all models.
The most common functions available are listed on this
page.
VCRs and DVRs
•
•
•
•
•
•
CHANNEL UP/DN
POWER
SLEEP
(FAST Forward)
(Pause)
(Play)
•
•
•
•
•
•
(Record)
(Reverse)
(Stop)
GUIDE (DVR only)
MENU (DVR only)
0–9 Number Buttons
Mitsubishi VCRs are compatible with some additional keys.
Cable Boxes and Satellite Receivers
(not all functions for all models)
TV
CAB/SAT
AUDIO
DVD
VCR
TV
CAB/SAT
AUDIO
DVD
VCR
Control modes
To use the remote after
programming, press the mode
key to match the control mode
to the device type.
•
•
•
•
•
•
•
•
•
•
PAGE UP/DOWN
Cancel
CHANNEL UP/DN
ENTER
GUIDE
POWER
LAST (ENTER; for channels on some models)
0–9 Number Keys
F1–F4 (A, B, C, D keys
on some models)
The record/playback
keys:
•
(FAST Forward)
•
(Pause)
•
(Play)
•
(Record)
•
(Reverse)
•
(Stop)
A/V Receivers
•
•
•
•
•
MUTE
POWER
SLEEP
VOLUME
0–9 Number Buttons
•
Direct Input Selection
buttons: numbers
and LAST (on some
Mitsubishi models)
CD Players
(not all functions for all models)
•
•
•
•
SLEEP
(FAST Forward)
(Pause)
(Play)
•
•
•
(Reverse)
(Stop)
0–9 Number Buttons
DVD Players
(not all functions for all models)
•
•
IMPORTANT
Some manufacturers may change their
products or they may use more than one
remote control system. The TV’s remote
control may be unable to operate your A/V
equipment in these cases.
•
•
•
•
•
CANCEL (on some
models)
CHANNEL UP/DN (for
track skip on some
models)
ENTER
MENU
POWER
SLEEP
•
•
•
•
•
•
•
(FAST Forward)
(Pause)
(Play)
(Record)
(Reverse)
(Stop)
0-9 Number Keys
For assistance call 1(800) 332-2119
74
Appendices
Appendix A: Programming the Remote Control, continued
Programming the Remote Control
1. Press one of the upper buttons on the remote
control to change to the correct mode for the
product you want to control. Refer to the table
below. Only one of each device type can be controlled in each mode.
IMPORTANT
You may need to reprogram the remote control after
changing the batteries. Record the codes for each
mode in the space provided to make this faster.
Code Verification
Mode
Affected Device
To determine the code programmed for any mode:
Cab/SAT
Cable Box
DTV Receiver
Satellite Receiver
1. Set the mode to the one you wish to verify.
2. Press and hold POWER on the remote control for
VCR
VCR
DVR
DVD Player/Recorder
3. Press keys 9 9 0
4. Press 1 and count the blinks of the power key.
DVD
DVD Player/Recorder
DVR
VCR
5.
Audio
several seconds until the key blinks twice and goes off.
A/V Receiver
Audio Amplifier
CD Player
2. Press and hold POWER on the remote control for
3.
4.
5.
6.
several seconds until the key blinks twice and goes
off.
Release the POWER key.
Enter the first five-digit code listed for your equipment in the reference tables that follow.
If you need to start over or wish to exit
programming mode, temporarily change to a
different device mode.
Point the remote control at the equipment and
press POWER. If the product has no power on/off
function, press a different key, such as
(Play),
(Stop), VOLUME UP, or MUTE.
• If the equipment responds, the remote control
is properly programmed.
• If the equipment does not respond, repeat
steps 4 and 5 with the next five-digit code
listed for your equipment.
Once you have found the correct code, write it in
the space below for future reference.
Mode
Device Type
Code
CABLE/SAT
VCR
DVD
AUDIO
For assistance call 1(800) 332-2119
Write down the number of blinks as the first digit of
the code.
Repeat step 4 for the second, third, fourth, and fifth
digits of the code.
Audio Lock: Universal A/V Receiver
Control
With Audio Lock enabled, the remote control operates volume and mute on an A/V receiver in all control
modes. Activate Audio Lock if you always use an A/V
receiver with your TV and other A/V equipment.
1. Program AUDIO mode for your A/V receiver as
2.
3.
described in “Programming the Remote Control” on
this page.
With the remote control in AUDIO mode, hold POWER
on the remote control for several seconds until the
key blinks twice and goes off.
Press keys 9 9 3 ENTER
The POWER key will blink twice to indicate Audio
Lock is active.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
1. Press and hold POWER for several seconds until it
2.
blinks twice and goes off.
Press keys 9 9 3 VOLUME UP.
The POWER key will blink four times to indicate Audio
Lock has cleared.
75
Appendices
Appendix A: Programming the Remote Control, continued
Audio Amplifiers
Altec
41742
Lansing
Anthem
42220
Bel Canto
41583
Design
Cary Audio
41879
Design
Classe
41461
Denon
42134
Durabrand
41561
Flextronics
41879
Halcro
41934
Harman/
40892
Kardon
Krell
42463, 41837
Left Coast
40892
Lenoxx
41561
Lexicon
41802, 41145
Marantz
42138, 40892
Mark
42405, 41483
Levinson
Parasound
42245, 41934
Philips
40892
Polk Audio
42242, 40892
Cable Boxes
Amino
Bright House
Cable One
Cablevision
Charter
Cisco
Comcast
Cox
Digeo
Director
General
Instrument
Homecast
i3 Micro
Insight
Jerrold
Knology
Mediacom
Motorola
Myrio
Pace
Panasonic
Pioneer
RCN
11822, 11602
11877, 11376
11877, 11376
11877, 11376
12187, 11877, 11376
11982, 11877, 10877
12576, 11982, 11877,
11376
11877, 11376
12187, 11187
10476
10476
12301
11602
11877, 11376
10476
11877
11877, 11376
11376, 11187, 10476
11822, 11602
11982, 11877, 11376
11982
11877, 10877
11376
Cable Boxes
Rogers
Scientific
Atlanta
Sejin
Shaw
Sony
Suddenlink
Time Warner
Tivo
CD Players
Burmester
California
Audio Labs
DKK
Garrard
Harman/
Kardon
Integra
JVC
Kenwood
KLH
Koss
LG
Magnavox
Marantz
McIntosh
MCS
MGA
Miro
Mitsubishi
MTC
NAD
Onkyo
Optimus
Panasonic
Parasound
Philips
Pioneer
Proceed
Quasar
RCA
Realistic
Rotel
Sherwood
Sony
Tascam
TDK
Teac
Technics
11877
11877, 10877
11602
11376
11006
11877, 11376
12187, 11877, 11376
12576
40420
40029
40000
40420
41202, 40173, 40083
40101
41294, 40072
40626, 40028
41318
41317
41208
40038
40626, 40038, 40029
41703
40029
40083
40000
40098, 40083
40420
41208
41327, 40101
40420, 40000
40752, 40388, 40029
40420
40626
41087
40420
40029
40420, 40053
40420
40420
41950
41364, 40490, 40185,
40100, 40000
40420
41208
40420
40029
CD Players
Victor
Wards
Yamaha
40072
40053
41292, 40490, 40036
Audio Accessories
Apple
41115
Denon
42502
Vizio
42454
Yamaha
42458
Video Accessories
ADB
12586, 12254
Amino
12482, 11673, 11615,
11481
AT&T
10858
Cisco
12517, 12345
KoolConnect 11481
Motorola
12378, 10858
Scientific
12517, 12345, 10858
Atlanta
SureWest
11481
Verizon
12378
A/V Receivers
Aiwa
41641, 41405, 41388
Alco
41390
AMC
41077
Anam
41609
Arcam
41189
Audiotronic 41189
Audiovox
41390
B&K
40820
Bose
41933, 41841, 41629,
41253, 41229, 40639
Carver
41189
Denon
42857, 42279
Electrohome 42026
Harman/
42443, 42241, 41306,
Kardon
41304, 40891
iLive
42013
Insignia
42175, 42169, 41893,
41077, 41030
Integra
41805, 41320, 41298
iSymphony
42258, 42018
JBL
41306
JVC
42331, 42239, 42040,
41495, 41374
Kenwood
41570, 41569, 41313
KLH
41428, 41412, 41390
LG
42284, 42197, 41293
Magnavox
41514, 41269, 41189
For assistance call 1(800) 332-2119
76
Appendices
Appendix A: Programming the Remote Control, continued
A/V Receivers
Marantz
42114, 41289, 41269,
41189
McIntosh
41289
Micromega 41189
Mitsubishi
41957, 41922, 41921,
41920, 41393
Myryad
41189
Nakamichi
41313
Onkyo
41805, 41531, 41320,
41298, 40842
Optimus
41023
Panasonic
41763, 41633, 41548,
41518, 41316, 41308,
41288, 41275, 42967,
42452, 42221, 41764
Philips
42470, 42459, 42311,
41269, 41266, 41189,
40891
Pioneer
41935, 41384, 41023,
40630
Polk Audio
42270, 41289
Proscan
41254
RCA
42041, 41609, 41511,
41390, 41254, 41023
Samsung
41868, 41500, 41304,
41295
Sherwood
42169, 41905, 41653,
41077
Sherwood
42169
Newcastle
Sony
41759, 41758, 41658,
41622, 41558, 41441,
41258, 41058, 42522,
42216, 42172, 41858,
41822
Stereophonics 41023
Sunfire
41313
Teac
41390
Technics
41518, 41308
Thorens
41189
Toshiba
41788
Venturer
41390
Yamaha
41476, 41376, 41375,
41331, 41276, 41176,
40376, 40176, 42471,
42467, 42061, 41815
Zenith
41293
Satellite Receivers
Bell
10775
ExpressVu
Crossdigital 11109
Satellite Receivers
DirecTV
11749, 11377, 11142,
10749, 10639, 10566,
10392, 10247, 1856,
11609, 11442, 11414,
11109, 11076
Dish
11775, 11505, 10775
Network
System
Dishpro
11775, 11505, 10775
Echostar
11775, 11505, 10775
Expressvu
11775, 10775
GE
10566
General
10869
Instrument
GOI
11775, 10775
HTS
11775, 10775
Hughes
11749, 11442, 11142,
Network
10749
Systems
Jerrold
10869
JVC
11775, 10775
LG
11414
Mitsubishi
10749
Motorola
10869
Next Level
10869
Panasonic
10701, 10247
Philips
11749, 11442, 11142,
11076, 10749
Proscan
10566, 10392
RadioShack 10869
RCA
10566, 10392, 10143
Samsung
11609, 11442, 11377,
11276, 11109
Sony
10639
Star Choice 10869
Tivo
11442, 11142
Toshiba
11749, 10790, 10749
Voom
10869
Zenith
11856
VCRs
ABS
Accurian
Admiral
Adventura
Aiko
Aiwa
Alienware
Allegro
America
Action
American
High
For assistance call 1(800) 332-2119
21972
20000
20048
20000
20278
20037, 20000
21972
20039
20278
20035
VCRs
Audiovox
Calix
Canon
Carver
CCE
Citizen
Craig
Crosley
Curtis
Mathes
CyberPower
Daewoo
Dell
Denon
DirecTV
Durabrand
Dynatech
Electrohome
Electrophonic
Emerex
Emerson
Fuji
Funai
Garrard
Gateway
GE
GFM
Go Video
GoldStar
Gradiente
Harley
Davidson
Harman/
Kardon
Headquarter
Hewlett
Packard
Hitachi
Howard
Computers
HP
Hughes
Network
Systems
Humax
Hush
iBUYPOWER
Instant
Replay
JVC
KEC
Kenwood
20278, 20037
20037
20035
20081
20278
20278, 20037
20037
20081, 20000
20278, 20162, 20060,
20035
21972
20278, 20045
21972
20042
20739
20039, 20038
20000
20043, 20037
20037
20032
21593, 20593, 20278,
20043, 20037, 20000
20035, 20033
21593, 20593, 20000
20000
21972
20060, 20035
21593
20614
20038, 20037
20000
20000
20081, 20038
20046
21972
20042, 20000
21972
21972
20739, 20042
20739
21972
21972
20035
20067
20278, 20037
20067, 20038
77
Appendices
Appendix A: Programming the Remote Control, continued
VCRs
Kodak
Linksys
Lloyd’s
LXI
Magnasonic
Magnavox
Marantz
Marta
Matsushita
Media
Center PC
MEI
Memorex
MGA
Microsoft
Mind
Minolta
Mitsubishi
Motorola
MTC
Multitech
NEC
Nikko
Niveus
Media
Northgate
Olympus
Optimus
Panasonic
Penney
Pentax
Philco
Philips
Pilot
Pioneer
Polk Audio
Portland
Presidian
Proscan
Pulsar
Quarter
Quartz
Quasar
RadioShack
Radix
Randex
20037, 20035
21972
20000
20037
20593
21593, 20593, 20081,
20039, 20035, 20000
20081, 20035
20037
20162, 20035
21972
20035
20162, 20048, 20046,
20039, 20037, 20035,
20000
20043
21972
21972
20042
20173, 20067, 20043
20048, 20035
20000
20000
20067, 20038
20037
21972
21972
20035
21062, 20593, 20162,
20048, 20037
21062, 20616, 20614,
20162, 20035
20042, 20038, 20037,
20035
20042
20035
21181, 21081, 20739,
20618, 20081, 20035
20037
20067
20081
20278
21593
20060
20039
20046
20046
20162, 20035
20000
20037
20037
VCRs
RCA
Realistic
ReplayTV
Ricavision
Runco
Samsung
Sanky
Sansui
Sanyo
Scott
Sears
Sharp
Sonic Blue
Sony
Stack 9
STS
Sylvania
Symphonic
Systemax
Tagar
Systems
Tashiko
Teac
Technics
Teknika
Thomas
Tivo
Toshiba
Totevision
Touch
Vector
Vector
Research
Video Concepts
Videomagic
Viewsonic
Villain
Voodoo
Wards
XR-1000
Yamaha
Zenith
ZT Group
20880, 20060, 20042
20048, 20046, 20037,
20035, 20000
20616, 20614
21972
20039
20739, 20045
20048, 20039
20067, 20000
20046
20045, 20043
20046, 20042, 20037,
20035, 20000
20848, 20048
20616, 20614
21972, 21032, 20636,
20035, 20033, 20032,
20000
21972
20042
21593, 20593, 20081,
20043, 20035, 20000
21593, 20593, 20000
21972
21972
20037
20000
20162, 20035
20037, 20035, 20000
20000
20739, 20636, 20618
21972, 21008, 20045,
20043
20037
21972
20045
20038
20045
20037
21972
20000
21972
20081, 20060, 20048,
20042, 20035, 20000
20035, 20000
20038
21139, 20039, 20037,
20033, 20000
21972
DVD Players
Accurian
Adcom
Aiwa
Akai
Alco
Allegro
Apex Digital
Arrgo
Astar
Audiovox
B&K
BBK
Bel Canto
Design
Blue Parade
Broksonic
California
Audio Labs
Cinea
CineVision
Citizen
Coby
Craig
Curtis
Mathes
CyberHome
30675
31094
30641
31089, 30770, 30695
30790
30869
31061, 31056, 31020,
31004, 30797, 30796,
30794, 30755, 30672
31023
31489
31041, 30790
30662
31224
31571
30571
30695
30490
30831
30869, 30833
32116, 31587, 31277,
30695
31628, 31351, 31177,
31165, 31107, 31086,
30852, 30778
30831
31087
31537, 31502, 31129,
31024, 31023, 30874,
30816
Daewoo
31172, 31169, 30869,
30833, 30784
Denon
32258, 30634, 30490
Disney
31270, 30675
Durabrand
31127, 31023
DVD2000
30521
Electrohome 32116
Emerson
30675, 30591
Enterprise
30591
Fisher
30670
Funai
30675
Gateway
31077
GE
30815, 30522
GFM
30675
Go Video
31075, 31044, 30869,
30833, 30744, 30741,
30715
GoldStar
30869, 30741
Grundig
30539
For assistance call 1(800) 332-2119
78
Appendices
Appendix A: Programming the Remote Control, continued
DVD Players
Harman/
Kardon
Helios
Hello Kitty
Hitachi
Hiteker
Humax
iLo
Initial
Insignia
Integra
JBL
JVC
jWin
Kawasaki
Kenwood
KLH
Lenoxx
LG
LiteOn
Magnavox
Marantz
McIntosh
Memorex
Microsoft
Mintek
Mitsubishi
Myryad
NAD
Norcent
Olevia
Onkyo
Oppo
Panasonic
Philco
Philips
PianoDisc
31229, 30702, 30582
32192, 32080
30831
30664, 30573
30672
31588, 31500
31472, 31348
31472
32596, 32428, 32095,
30675
32147, 31769, 30627,
30571
30702
32365, 31602, 31550,
31275, 31164, 30867,
30623, 30558
31049
30790
30534, 30490
31020, 30790
31127
31602, 30869, 30741,
30591
31656, 31058
31506, 31472, 31354,
31177, 30675, 30646,
30539, 30503
32414, 30539
31273
32213, 31270, 30831,
30695
32083, 30522
31472
31521, 30521
30894
32572, 30741
31107, 31003
32331
32147, 31769, 30627,
30503
32545, 32185, 31224,
30575
31762, 31641, 31579,
30703, 30632, 30503,
30490
30675
32084, 32056, 31340,,
31267, 30675, 30646,
30539, 30503, 32434,
31506, 31354
31024
DVD Players
Pioneer
31571, 31512, 31460,
30632, 30631, 30571,
30525, 30142
32442
Polaroid
31086, 31061, 31020
Polk Audio
30539
Portland
30770
Presidian
30675
Proceed
30672
Proscan
30522
ProVision
30778
RCA
32213, 31769, 30822,
30790, 30571, 30522
Rio
30869
Rotel
31178, 30623
Sampo
30752
Samsung
32069, 31470, 31075,
31044, 30820, 30573,
30490, 30199
32556, 32489, 32369,
32329
Sansui
30695
Sanyo
30873, 30695, 30670
Schneider
30646
Sharp
32250, 31256, 30752,
30675, 30630
Sherwood
31077, 31043, 30770,
30633
Sherwood
31077
Newcastle
Shinsonic
30533
Sonic Blue
30869
Sony
31633, 31536, 31516,
31431, 31070, 31033,
30864, 30533
Sylvania
30675
Symphonic
30675
TAG
30894
McLaren
Teac
30790
Technics
30703, 30490
Theta Digital 30571
Tivo
31512, 31503
Toshiba
31769, 31588, 31515,
31510, 31503, 31154,
30695, 30503
32277, 32006, 31608
Urban Con- 30503
cepts
Venturer
30790
Vizio
32563, 31226, 31064
Xbox
32083, 30522
For assistance call 1(800) 332-2119
DVD Players
Yamaha
32558, 32298, 30817,
30646, 30545,
30539, 30490
Zenith
30869, 30741, 30591,
30503
Blu-ray and HD-DVD
Denon
32258
Insignia
32596, 32428, 30675
Integra
32147, 31769
JVC
32365
LG
31602, 30741
Magnavox
30675
Marantz
32414
Microsoft
32083
NAD
32572
Olevia
32331
Onkyo
32147, 31769
Oppo
32545
Panasonic
31641
Philips
32434, 32084
Pioneer
32442, 30142
RCA
31769
Samsung
30199
Sharp
32250
Sony
31516
Sylvania
30675
Toshiba
31769, 31515
Vizio
32563
Xbox
32083
Yamaha
32298
Appendices
Appendix B: Bypassing
the Parental Lock
79
Mitsubishi Home Theater TV
154 Series
164 Series
265 Series
Lock Bypass Instructions Have Been Filed for
Future Reference
Bypassing the Parental Lock
After you set the lock, you must use your pass code to:
• View a locked program
• View a locked channel
• View the locked TV
• Cancel the lock
• Enter the Lock menus
If you forget your pass code, you can view the locked
TV without entering your pass code. When prompted
for the pass code, press the number 9 and LAST keys on
the TV remote control at the same time. This process
temporarily unlocks the TV.
When entering the Lock menu, you will be prompted to
enter a pass code.
•
To change the pass code, press 9 and LAST at the
same time. Either enter a new pass code to open
the Lock menu and make changes or press EXIT to
close the menu.
•
If any of the locks are turned on and you exit the
menus when prompted for a new code, the old
code and all lock settings will be retained.
•
If all locks are turned off and you exit the menus
when prompted for a new code, then the previous
code will be erased.
IMPORTANT
When changing or deleting your pass code,
you must use the remote control included
with this TV. You cannot use a Mitsubishi
remote control from another component or a
“universal” remote.
IMPORTANT
Cut along the dotted line and file bypass
instructions in a safe place for future
reference.
For assistance call 1(800) 332-2119
80
Appendices
This page intentionally left blank
For assistance call 1(800) 332-2119
Appendices
81
Appendix C: HDMI Control of CEC Devices
Many new HDMI devices have a feature called Consumer Electronics Control (CEC) or HDMI Control.
HDMI Control allows one device, such as the TV, to
control other devices, such as an A/V receiver or disc
player. Use of CEC is optional.
Each manufacturer chooses which CEC functions to
support so it is difficult to predict which devices and
features are compatible with Mitsubishi’s HDMI Control.
You may find that CEC functions for a specific device are
limited.
To use HDMI Control, you must enable it in both
the TV and the device.
• In the TV. Enable HDMI control from the New
Device Found screen or from the Inputs > HDMI
Control menu.
• In the Device. Most devices with HDMI CEC compatibility let you turn it on or off in the device menus,
where it is typically listed as “HDMI Control.”
Enabling HDMI Control of CEC Devices
To ensure proper detection
• Power on HDMI devices before connecting them to
the TV.
• Connect and set up HDMI devices one at a time.
1. Power on the device and allow it to complete the
power-on sequence (boot up). Stop any playback.
2. Connect the device to one of the TV’s HDMI inputs.
3. When the TV detects the connection, the New
Device Found screen will appear.
Note: See “If the New Device Found Screen Has No
HDMI Control Option” on this page if there is no
HDMI Control option.
New Device Found screen with HDMI Control option.
This screen displays only if the device’s HDMI Control is
enabled.
4. If prompted for a name,
highlight a name for the
device and press ENTER to
add a check. The device
itself may later override the
name assigned.
5. Highlight On and press
ENTER to add a check.
7. Highlight EXIT and press ENTER to close the New
Device Found screen.
Note: At any time after completing Auto Input Sensing, you can set the TV’s HDMI control on or off
in the Inputs > HDMI Control menu.
8. 265 Series. To supplement HDMI control with
NetCommand IR control, see page 60.
If the New Device Found Screen
Has No HDMI Control Option
If the New Device Found screen shows no option for
HDMI Control, one of these conditions applies:
• HDMI Control is turned off in the menus of the
new device
Action:
a. Highlight EXIT and press ENTER to close the
New Device Found screen.
b. Display the device’s setup menus and enable
the device’s CEC capabilities.
c. Wait for the TV’s New Device Found screen
to appear again.
d. If the New Device Found screen does not
appear, power off the device. Power on the
device and wait for the New Device Found
screen to display with the HDMI Control
option.
• The HDMI cable cannot support CEC
Action:
Upgrade your HDMI cable to one that supports
CEC.
• The device does not have CEC compatibility
Action:
-- Control the device with its own remote
control or program the TV’s remote control to
operate the device.
-- 265 Series. Use the TV’s NetCommand IR
control (page 60).
For assistance call 1(800) 332-2119
82
Appendices
Appendix C: HDMI Control of CEC Devices, continued
HDMI Control of an HDMI A/V
Receiver and Connected Devices
Note: Connect the A/V receiver to the TV with an
HDMI cable before making other connections.
1. Enable HDMI Control for the A/V receiver as
2.
3.
4.
5.
described in “Enabling HDMI Control of CEC
Devices” on the previous page.
Power on the HDMI device you wish to connect to
the A/V receiver (such as a disc player, cable box,
or satellite receiver). Allow the device to complete
the power-on sequence (boot up). Stop playback if
the device starts playing.
Connect the device to the A/V receiver with an
HDMI cable.
Select the device’s HDMI input on the A/V receiver’s front panel controls or remote control.
When the TV detects the connection, the New
Device Found screen will appear.
Note: If the TV is unable to detect the device, either
the device’s CEC capability is not enabled or
the device is not CEC compatible. Enable
HDMI control through the device’s menus
before continuing. You may need to temporarily connect the device directly to the TV to view
device menus.
6. Highlight On and
press ENTER to
add a check.
7. Highlight EXIT and press ENTER to close the New
8.
Device Found screen.
Optional: Connect the TV’s DIGITAL AUDIO
OUTPUT to an input on the A/V receiver. Use this
additional connection if:
• You want the ability to switch between the A/V
receiver speakers and the TV speakers.
• You want to use the A/V receiver to listen to
devices connected to the TV only, e.g., an
antenna input or camcorder.
9. 265 Series. If desired, perform NetCommand IR
Learning to supplement CEC functions. You must
first connect and place IR emitters for the devices.
See page 60.
For assistance call 1(800) 332-2119
TV
HDMI cable
Optional
digital audio
connection
HDMI OUT
OPTICAL
AUDIO IN
A/V receiver with
HDMI output
HDMI
cables
VCR
High-definition
DVD player
Devices with HDMI
output to A/V receiver
DVD player
Cable box
Connecting HDMI devices. The optional digital audio
connection allows you to hear audio through the A/V
receiver from devices connected to the TV only.
83
Appendices
Appendix C: HDMI Control of CEC Devices, continued
Resolving CEC Conflicts
Using HDMI Control
Because each manufacturer selects which CEC functions to support, some devices can conflict with other
devices. If control conflicts arise, you can:
• Turn off TV control of an individual CEC-enabled
device (see below).
• Turn off CEC in the setup menu of one of the
devices.
As an example of using HDMI Control, press PLAY on
the device itself to:
• Power on the TV
• Switch to the device (no need to display the
Input Selection menu)
• Begin play of the device
Turning Off the TV’s HDMI Control of a CEC Device
Test your equipment with the TV’s remote control to
find additional supported commands. See the table
below for commands that may be available, depending
on the individual device.
1. Press MENU on the TV remote control.
2. Highlight Inputs > HDMI Control.
3. Move to the device name and press ENTER to select
4.
Off to turn off the TV’s ability to control the device.
Press EXIT to clear the menu.
Inputs > HDMI Control menu
Removing an HDMI Device
1. Power off the device.
2. Disconnect the HDMI cable.
3. Press MENU on the TV remote control to enter the
4.
5.
6.
TV main menu.
Go to Inputs > Name.
Highlight the HDMI input name and press ENTER to
select Delete.
Press EXIT to clear the menus.
Direct Keys
CEC-enabled VCR, DVD, and DVR functions that
may be available:
Record/
Playback
Menu
Navigation
Channel
Tuning
Other
CH
Guide
Enter
Digits 0–9,
CANCEL
CANCEL
(to cancel)
ENTER
TOOLS
Check the
TOOLS menu
for supported
functions.
If you have a CEC-enabled A/V receiver, CEC-enabled
devices connected to the A/V receiver with an HDMI
cable may also be controllable. They can be selected
from the TV’s Input Selection menu.
CEC-enabled A/V receiver functions that may be
available:
• Try the VOL, MUTE, and menu-navigation keys.
• To open the A/V receiver menu, follow these steps:
1. While watching TV, press AUDIO.
2. Press until the TV Speakers option displays.
3. Press to select Off (to send audio to the A/V
receiver).
4. Press INPUT and highlight the A/V receiver icon
in the Input Selection menu.
5. Press TOOLS.
6. Select Menu from the Tools menu.
Inputs > Name menu with Delete selected for HDMI-3.
For assistance call 1(800) 332-2119
84
Appendices
Appendix D: TV Care
Cleaning Recommendations
Normally, light dusting with a dry, non-scratching duster
will keep your TV clean. If cleaning beyond this is
needed, please use the following guidelines:
First, turn off the TV and unplug the power cord from
the power outlet.
Occasionally clean dust build-up from the air-intake
grilles on the back and sides of the TV. Clean using a
vacuum cleaner with a brush attachment.
Top and Sides of the TV
•
Gently wipe down your TV with a soft, non-abrasive
cloth such as cotton flannel, microfiber, or a clean
cloth diaper, lightly moistened with water. Dry with
a second dry, soft, non-abrasive cloth.
Care of the Remote Control
Remote Control Tips
•
•
•
•
•
•
•
•
For longer life, use alkaline batteries.
Do not mix old and new batteries.
Be within 20 feet of the equipment.
Do not press two or more keys at the same time
unless instructed to do so.
Do not allow the unit to get wet or become heated.
Keep the unit out of direct sunlight.
Avoid dropping on hard surfaces.
Do not use harsh chemicals to clean. Use only a
soft, lightly moistened cloth.
Resetting the Remote Control
•
For oily dirt, add a few drops of mild liquid detergent, such as dishwashing detergent, to the water
used to moisten the cloth. Rinse with a second
cloth moistened only with water. Dry with a third
dry, soft, non-abrasive cloth.
Screen
IMPORTANT
DO NOT apply any type of liquid to the surface of
the TV screen.
•
•
•
Use only a soft, dry cloth to clean the LCD
screen. Do not use any liquids.
Wipe the screen gently with an up and down
motion.
Clean the entire screen evenly, not just sections of
the screen.
General Cleaning Precautions
•
•
•
•
•
DO NOT allow liquid to enter the TV through the
ventilation slots or any crevice.
DO NOT use any strong or abrasive cleaners, as
these can scratch the surfaces.
DO NOT use any cleaners containing ammonia,
bleach, alcohol, benzene, or thinners, as these can
dull the surfaces.
DO NOT spray liquids or cleaners directly on the
TV’s surfaces.
DO NOT scrub or rub the TV harshly. Wipe it gently.
For assistance call 1(800) 332-2119
If TV mode is selected and the TV does not respond
properly, reset the remote control.
1. Press and hold POWER for several seconds until the
mode indicator blinks twice and goes off.
2. Release the POWER key.
3. Press keys 0 0 9 3 5 and the mode indicator will
blink twice when you finish entering the code.
When entering the code, pause for a moment
between each key press to ensure it is recognized.
Low-Battery Indicator
If you press a key and the mode indicator blinks five
times, replace the remote control’s batteries.
Appendices
85
Appendix E: Troubleshooting
TV Reset Comparison Guide
You can resolve many common TV problems using
the reset functions described in the following table.
See also the troubleshooting suggestions later in this
appendix.
IMPORTANT
Before you change sound or picture settings: If
picture or sound settings seem wrong for a broadcast
channel (a channel from the ANT input, a cable box, or
satellite receiver), first check other channels from the
same input before changing settings. If most other
channels from the same input seem correct, there is
likely a problem with the broadcast rather than with the
TV. Use care in this case, as changes you make to fix
problems on individual channels also affect all other
channels on the same input.
Reset Name
When to Use
How to Use
Resulting Action
Format
If the picture shape
(aspect ratio) seems
incorrect, use the
FORMAT key to change
the shape of the
picture.
Press FORMAT to cycle through the
aspect ratios available for the signal.
The last-used format for a signal
type is memorized for each input.
The next time the same input and
signal type are viewed, the lastused format will be recalled.
PerfectColor™/
PerfecTint™
Reset (265
Series)
(for the single
input currently
being watched)
When the color
1. While viewing the input to be
intensities seem out
reset, press MENU and go to
of balance, use the
Picture > Perfect.
PerfectColor/PerfecTint 2. Press ENTER to display the
reset to reset the color
PerfectColor adjustment screen.
balances to the original
3. Press CANCEL to reset the colors.
factory settings.
Both PerfectColor and
PerfecTint are reset at
the same time.
All PerfectColor/PerfecTint
sliders are reset to the original
center position. The PefectColor/
PerfecTint settings for other
inputs remain unchanged.
A/V Memory
Reset
(for the single
current input)
When audio and/
or video settings for
a single input seem
incorrect, use A/V
Memory Reset to
return the input to
the original factory
settings.
During General TV Viewing
1. While viewing the input to reset,
press MENU and go to Picture >
Reset.
2. Press ENTER to highlight Reset.
3. Press ENTER again to reset.
All Audio and Video settings for
the individual input are reset
except for the global settings
for audio Balance, Listen To,
Language, True 120 Hz/True 240
Hz, and settings in the Picture >
Advanced menu.
While Using VUDU Movies and
Some VUDU Apps
Press TOOLS and 3.
Service and Customer Support
Customer Support
Service
• To order replacement or additional remote controls, visit our website at www.mitsuparts.com or
call (800) 553-7278.
If you are unable to correct a problem with your TV,
consult your Mitsubishi dealer or Mitsubishi Consumer Relations at (800) 332-2119.
• DO NOT adjust any controls other than those
described in this Owner’s Guide.
• DO NOT remove the protective back cover of
your TV.
• For questions:
Call Consumer Relations at 800-332-2119.
E-mail: MDEAservice@mdea.com
Website: www.mitsubishi-tv.com
For assistance call 1(800) 332-2119
86
Appendices
Appendix E: Troubleshooting, continued
Reset Name
When to Use
How to Use
Resulting Action
A/V Reset
(for all inputs)
To reset audio and
video adjustments for
all inputs to the original
factory settings.
While viewing the TV, press the
control-panel buttons INPUT and
VOLUME DOWN at the same time for at
least two seconds.
All Audio and Video settings are
returned to the original factory
settings, including global settings
not affected by Picture > Reset.
Channel
Memorization
To erase and
re-memorize channels
on the Ant input.
1. While viewing the TV, press
MENU to display the main menu.
2. Navigate to the Setup >
Channel menu.
3. Highlight the reception mode,
e.g. Ant Air.
4. Select All channels.
5. Highlight Scan.
6. Press ENTER to start channel
memorization.
All previously memorized channels for the antenna input are
erased and a new set of memorized channels is created. To
add or delete individual channels,
see the Setup > Channel > Edit
menu instructions on page 53.
Lock Menu
Pass Code
To change your Lock
menu pass code
See the cutout page from Appendix B,
page 79.
Allows establishment of a new
code.
Control-Panel
Lock Release
To re-enable the
control-panel buttons
after activation of the
Control-Panel Lock
Press and hold the INPUT button on
the control panel for ten seconds. If
the TV is powered off, you can then
press the POWER button to turn it on.
Allows the control panel to be
unlocked if the remote control is
misplaced.
Auto Input
Sensing for
HDMI
If the New Device
Found screen does
not appear when you
connect an HDMI
device.
1. Disconnect the HDMI device.
2. Delete the HDMI input in the
Inputs > Name menu (see page
55).
3. Power on and connect the new
device.
The New Device Found screen
will display.
System Reset
If the TV does not turn
on or off, does not
respond to the remote
control or controlpanel buttons, or has
audio but no video.
Press and hold the POWER button on
the control panel for ten seconds.
The TV will turn off. Power on the
TV and the green LED will flash
quickly for about one minute. The
changes you made most recently,
before using SYSTEM RESET, may
be lost.
TV Reset
To reset all consumeraccessible settings
and all memories to
the original factory
defaults.
1. While viewing the TV, press
MENU to display the TV main
menu.
2. With the main menu displayed,
press number keys 1 2 3 to
display the Reset menu.
Use TV Reset if the TV
3. READ THE ON-SCREEN
can respond to conWARNING AND INSTRUCtrols but TV behavior is
TIONS.
abnormal.
• If you do not wish to use this
CAUTION: All ownerreset, press EXIT or MENU to
performed setups and
back out.
adjustments will be
• If you do wish to use the
erased.
reset, press ENTER to erase
all memories and settings.
The TV will start the initialization
process and then turn off.
Power on the TV and the front
green LED will start flashing. All
memory and settings outlined in
this Owner’s Guide will need to
be set again.
IMPORTANT:
Use this reset
only if other
troubleshooting
has been unsuccessful.
For assistance call 1(800) 332-2119
Appendices
87
Appendix E: Troubleshooting, continued
Reset Name
When to Use
How to Use
Resulting Action
VUDU
Reset VUDU
Account Password
You have forgotten
your account password.
Using a computer, go to
www.VUDU.com.
Reset your account password
from the VUDU website (requires
access to e-mail).
VUDU
Reset Parental
Controls Pass
Code
You have forgotten
your pass code.
Call VUDU Customer Care at
1-888-554-VUDU (8838).
VUDU Customer Care will reset
your pass code.
General TV Operation
Symptom
Remarks
1.
The TV remote control does not work.
•
•
•
•
•
2.
When I try to use the remote control, the POWER
key blinks five times.
Replace the batteries.
3.
TV does not respond to the remote control or •
to control-panel buttons and TV will not power •
on or off.
Unplug the AC power cord for 10 seconds.
Press and hold the POWER button on the control panel to
perform system reset.
4.
When a device is selected from the Input
Selection menu, the screen is blue or black (no
signal source).
•
•
Make sure the selected device is turned on.
Begin play of the device.
5.
You have forgotten your Lock menu pass code.
See “Bypassing the Parental Lock”, Appendix B.
6.
Rating restrictions are not working.
Open the Lock > Parental menu and:
• Verify that the ratings locks are active.
• Check the Lock Time/Unlock Time to check if rating restrictions are disabled.
• Rating restrictions apply only to content on the ANT input.
7.
On-screen displays appear each time you
change a function.
Normal TV operation.
8.
A warning message appeared on screen
stating, “TV will shut down in a few seconds.
Please check if the air flow is blocked.”
•
I have turned on CEC for my HDMI devices but
control is erratic and I wish to disable it.
•
9.
•
•
•
Check that the batteries are fresh and installed correctly.
Check that the control mode on the remote is set to TV.
Be no more than 20 feet from the TV when using the remote control.
Program the remote control to operate the TV or other device.
Reset the remote control. See “Resetting the Remote Control,”
page 84.
Internal TV temperature has exceeded proper levels. Cool
the room.
The TV has overheated. Clear blocked air vents and ensure
at least four inches of clearance on all sides of the TV.
First turn off the TV’s HDMI control for the specific device.
Open the Inputs > HDMI Control menu, select the device,
select Off.
Disable CEC on the device itself. See the device’s instructions.
If the problem persists, do the following:
1. Disconnect the device from the TV.
2. Open the Inputs > Name menu and select Delete for
the device.
3. Reconnect the device to the TV and Auto Input Sensing
will recognize the device with CEC disabled.
For assistance call 1(800) 332-2119
88
Appendices
Appendix E: Troubleshooting, continued
TV Channels
1.
Symptom
Remarks
The TV takes several seconds to respond to
channel changes.
•
•
•
•
2.
You cannot access a channel.
•
•
•
•
•
•
3.
When ChannelView list is displayed, information appears incomplete
•
•
•
•
It is normal for digital channels to take longer to tune in.
Press ENTER after entering a channel number to minimize
delays.
Use a 4-digit number for an over-the-air digital channel.
Use a 6-digit number for digital cable channels if your cable
service is able to recognize 6-digit channel numbers.
Use number keys instead of CH.
Be sure the channel you want to view is in memory.
Check that the TV is switched to the correct device or
antenna for that channel by pressing the INPUT key.
Make sure the Lock > Parental menu lock is set to Off.
If you cannot tune to a virtual digital channel even though the
TV has already memorized digital channels, tune to the physical channel number used by the broadcaster. The virtual
channel will then be automatically added to memory.
You may be trying to tune to an analog channel that is no
longer broadcasting.
Press INFO to update the display for the highlighted channel.
Program information is displayed only for the currently tuned
channel.
Available information is sent from the broadcaster or cable
provider. No other data is available.
Make sure the TV clock is set correctly.
TV Power On/Off
Symptom
Remarks
1.
TV takes an excessively long time to power
on.
When powered on, the TV needs time to boot up, just as a computer does.
2.
You cannot program the TV to turn on automatically (Timer function)
•
•
The TV may be locked.
The clock may not be set.
3.
TV turned itself off and the light on the front
panel started to blink.
•
Momentary power fluctuation can cause the TV to turn off
to prevent damage. Wait for the green light to stop flashing
and turn the TV on again.
If the TV does not stay on, press the POWER button on the
control panel for at least eight seconds to perform System
Reset. If this happens frequently, obtain an AC line power
conditioner/surge protector.
An unusual digital signal may have been received, triggering a
protection circuit. Wait for the light to stop flashing and turn TV
on.
•
•
4.
TV will not power off.
For assistance call 1(800) 332-2119
Press the POWER button on the control panel for ten seconds to
perform System Reset.
Appendices
89
Appendix E: Troubleshooting, continued
Picture
Symptom
Remarks
1.
Picture does not look like a high-definition
picture.
Not all signals are high-definition signals. To receive high-definition programming from your cable or satellite provider, you must
subscribe to the provider’s high-definition service. Some overthe-air broadcasts are in high-definition and can be received with
a high-quality antenna suited to your location.
2.
TV has sound but no picture.
•
•
•
Press MENU on the remote control. If the menu displays,
then there is a problem with the incoming signal.
Check that all video inputs are plugged in firmly.
Press and hold the POWER button on the control panel for ten
seconds to perform System Reset.
3.
You cannot view a picture when playing a
VHS tape.
Check your VCR’s owner’s guide for further troubleshooting.
4.
VCR or DVD player’s on-screen menus jitter
up and down.
Stop playback. Possible cause: Many VCRs and DVD players
provide on-screen menus at only half-resolution that may
appear to jitter up and down.
5.
When viewing a stopped VCR, white lines
are rolling on the screen.
•
•
•
6.
A color program appears as a black and
white image, or the colors are dim, or the
screen is black.
The PerfectColor color balance has been incorrectly set. Reset
the PerfectColor balance.
7.
Picture from an HDMI input is noisy (poor
quality).
Upgrade a standard (unmarked) HDMI cable to a high-speed
HDMI cable.
8.
The image from a computer appears distorted when viewed on the TV.
•
•
Turn off video mute for the VCR.
Begin playing the tape.
Change the VCR input from Line 1 to the VCR antenna input.
Normal TV operation. The TV does not correct distortion in
the picture from a computer because the correction process
may cut off the edges of the image.
The aspect ratio may be wrong for the image. Press FORMAT
to change.
For assistance call 1(800) 332-2119
90
Appendices
Appendix E: Troubleshooting, continued
Sound
1.
Symptom
Remarks
There is no sound even when the
volume is turned up.
•
•
•
•
•
•
Check if the MUTE key is on.
The TV’s analog Listen to setting may be set to SAP (analog
program from the ANT input) but no SAP is being broadcast.
Check that the Sound > Audio > TV Speakers option is set to On
to hear sound from the TV speakers. Possibly the TV Speakers
option is Off or set to Center but there is no A/V receiver connected.
If using an A/V receiver, check that the Sound > Audio > TV
Speakers option is set to Off to hear sound from the A/V receiver
speakers.
Press and hold the POWER button on the control panel for 10
seconds to perform System Reset.
The language selected in the Setup > Antenna Digital Audio
menu is not being broadcast for the current program.
2.
The sound does not match the screen
picture.
The TV’s analog Listen to setting may be set to SAP (analog program
from the ANT input).
3.
The sound from my A/V receiver does
not match the screen picture (I should
hear the correct audio from my A/V
receiver).
•
•
Check that DIGITAL AUDIO OUTPUT and/or AVR/SURROUND
OUTPUT on TV’s connection panel is connected to the A/V
receiver.
Without this connection, devices connected only to the TV (and
not the A/V receiver) can be heard only from the TV speakers.
Note that this includes the ANT input, a device (such as a
camcorder) connected to the TV, and any other device sending
audio to the TV only.
If using a NetCommand-controlled A/V receiver, NetCommand
may be selecting the wrong A/V receiver audio input. Check the
A/V receiver’s NetCommand setup in the Inputs > AVR menu.
4.
Cannot select an audio-only device; it
does not appear in the Input Selection
menu.
Plug an unused video plug into the Y/VIDEO jack to activate Auto
Input Sensing. Assign the name CD/Audio or MP3 to make the
audio device selectable in the Input Selection menu.
5..
Sound is coming from the TV speakers
instead of the A/V receiver.
•
•
For assistance call 1(800) 332-2119
Connect the TV’s AUDIO OUT to the A/V receiver.
Change TV Speakers setting to Off or Center.
Appendices
91
Appendix E: Troubleshooting, continued
NetCommand IR Control (NetCommand-equipped models only)
Symptom
Remarks
1.
•
NetCommand unable to learn specific device
keys.
•
•
•
•
A/V Device does not use IR format for remote control
signal. ITT and RF formats cannot be learned.
Room lighting may affect the signal. Have the remotes very
close (6 inches or less) to the TV during Learning.
Some, but not all, device key functions can be learned
by NetCommand. For example, POWER and PLAY may be
learned, but other functions may not.
The signal from the remote control may not be strong
enough. Insert fresh batteries and try Learning again.
The key was “learned” correctly but can be accessed only
from the Tools menu.
2.
The A/V receiver is the selected audio source A/V Receiver Set Up for Audio and Video Switching over HDMI
but there is no sound.
-- Check to see if the A/V Receiver power is turned on.
-- If the device is connected only to the TV (e.g., on
ANT or a front panel input), verify that the TV’s AUDIO
OUTPUT is connected to the A/V receiver and the
correct key has been “learned.”
-- The A/V receiver is not switching properly because
you have not learned the IR codes for the A/V receiver
inputs to which your devices are connected.
3.
There is no sound or picture from the A/V
receiver for my DVD player or other device
connected to the A/V receiver; the A/V
receiver should be sending video to the TV
over an HDMI cable.
(A/V Receiver Set Up for Audio and Video
Switching over HDMI)
The NetCommand A/V receiver setup is not switching audio
and video inputs properly because you did not “learn” the
A/V receiver’s IR codes for the device inputs. See “Automatic
Audio/Video Switching Over an HDMI Connection,” page 69.
4.
I’ve selected my DVD player or other surround sound device in combination with the
TV speakers but hear no sound from the TV
speakers.
A/V Receiver Set Up for Audio and Video Switching over HDMI
With your DVD player connected to the A/V receiver, only
video is passed from the A/V receiver to the TV because of
copy-protection restrictions on the HDMI signal
5.
I “learned” the RECORD key for my VCR/DVR
but when I pressed the RECORD key, the VCR/
DVR did not record anything.
Check that the VCR or DVR is receiving a signal directly from
your cable box or satellite receiver.
For assistance call 1(800) 332-2119
92
Trademark and License Information
Trademark and License Information
LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY
EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS,
INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Manufactured under license from Cambridge Mechatronics Ltd.
Rapidfire and the 1... logo are trademarks of Cambridge Mechatronics Ltd
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by Mitsubishi Electric is under license. Other trademarks and trade names are those of their respective owners.
Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories.
ENERGY STAR® and the ENERGY STAR mark are registered U.S. marks. ENERGY STAR is a registered mark owned
by the U.S. government.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Imaging Science Foundation Certified Calibration Controls
The software in this TV is based in part on the work of the Independent JPEG Group, copyright © 1991-1998, Thomas
G. Lane, all rights reserved.
VUDU™ is a trademark of VUDU, Inc.
“x.v.Color” and the “x.v.Color” logo are trademarks of Sony Corporation.
ChannelView™, DeepField™ Imager, Easy Connect™, EdgeEnhance™, NetCommand®, PerfectColor™, PerfecTint™,
Plush 1080p® 5G, StreamTV™, Unisen™ are trademarks of Mitsubishi Digital Electronics America, Inc.
For assistance call 1(800) 332-2119
Trademark and License Information
93
Mitsubishi TV Software
END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE
IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and
Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”). By
utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property laws
and treaties. The Software is licensed, not sold.
1.
LICENSE GRANT. MDEA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the Software
only with the Mitsubishi television model that included this owner’s guide and owned by you.
2.
RIGHTS AND LIMITATIONS.
Software Not for Resale. You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the TV that
Software has been pre installed.
Prohibition on Reverse Engineering, Decompilation and Disassembly. The Software contains trade secrets or other proprietary material
in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise reduce the
Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by applicable law.
Separation of Components. The Software is licensed as a single product. Its component parts may not be separated for use on more
than one TV.
No Rental. You may not rent, lease, lend, or sublicense the Software.
Trademarks. This License Agreement does not grant you any rights to any trademarks of MDEA.
3.
VIOLATIONS. You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License,
may subject you to serious criminal and civil penalties including damages and an award to MDEA of attorneys’ fees in connection with any
violation of this License. You further understand that you may be held legally responsible for any copyright infringement or other violation
of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License. This license
is effective until terminated, and will terminate immediately without notice from MDEA or judicial resolution if you fail to comply with any
provision of this License.
4.
COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs,
animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed materials are owned
by or licensed to MDEA. All title and intellectual property rights in and to the content which may be accessed through use of the Software
is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and
treaties. This License Agreement grants you no rights to use such content, except that you own the media on which the Software is
recorded, but MDEA and its licensors retain ownership of the Software itself. All rights not expressly granted are reserved by MDEA.
5.
EXPORT RESTRICTIONS. MDEA is licensing the Software for use within the United States. You agree that you will not
export or re-export the Software. You specifically agree not to export or re-export the Software: (i) to any country to which the U.S. has
embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Iraq, Libya,
North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the Software
back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design, development,
or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from participating in
U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the BXA nor any other U.S.
federal agency has suspended, revoked, or denied your export privileges.
6.
DISCLAIMER OF WARRANTY. EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED WARRANTY
APPLICABLE TO THE TV, MDEA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SOFTWARE
AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH
RESPECT TO THE SOFTWARE. ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED BY MDEA. IN
NO EVENT SHALL MDEA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT OR OTHERWISE, FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE. BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATION MAY
NOT APPLY TO YOU.
7.
LIMITATION OF LIABILITY. MDEA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR
OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR EXPENDITURES
MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE. YOU AGREE THAT NEITHER MDEA’S
BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE A FAILURE OF THE
ESSENTIAL PURPOSE OF THIS LICENSE. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. MDEA’s
liability to you for direct damages for any cause whatsoever and regardless of the form of the action, will be limited to the money
paid by you for the TV (based on fair market value of the TV) that caused the damages.
8.
GENERAL. This License Agreement will be governed by the laws of the State of California.
WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects
or other reproductive harm.
For assistance call 1(800) 332-2119
94
Trademark and License Information
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright © 2007 Free Software Foundation, Inc. <http://fsf.org/>
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The GNU General Public License is a free, copyleft license for software and other kinds of works.
The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public
License is intended to guarantee your freedom to share and change all versions of a program--to make sure it remains free software for all its users. We, the Free
Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work released this way by its authors. You can apply it to
your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute
copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in
new free programs, and that you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you
distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must
make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to
copy, distribute and/or modify it.
For the developers’ and authors’ protection, the GPL clearly explains that there is no warranty for this free software. For both users’ and authors’ sake, the GPL requires
that modified versions be marked as changed, so that their problems will not be attributed erroneously to authors of previous versions.
Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users’ freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to prohibit the practice for those products. If such
problems arise substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom
of users.
Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on general-purpose
computers, but in those that do, we wish to avoid the special danger that patents applied to a free program could make it effectively proprietary. To prevent this, the GPL
assures that patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or
organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The resulting
work is called a “modified version” of the earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright
law, except executing it on a computer or modifying a private copy. Propagation includes copying, distribution (with or without modification), making available to the
public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer network, with
no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work
under this License, and how to view a copy of this License. If the interface presents a list of user commands or options, such as a menu, a prominent item in the list
meets this criterion.
1. Source Code.
The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular
programming language, one that is widely used among developers working in that language.
The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component,
but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which
an implementation is available to the public in source code form. A “Major Component”, in this context, means a major essential component (kernel, window system,
and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the work, or an object code interpreter used to run
it.
The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and
to modify the work, including scripts to control those activities. However, it does not include the work’s System Libraries, or general-purpose tools or generally available
free programs which are used unmodified in performing those activities but which are not part of the work. For example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to
require, such as by intimate data communication or control flow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
2. Basic Permissions.
All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License
explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its
content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities for running those works, provided that you
comply with the terms of this License in conveying all material for which you do not control copyright. Those thus making or running the covered works for you must do
so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it unnecessary.
3. Protecting Users’ Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty
adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing,
against the work’s users, your or third parties’ legal rights to forbid circumvention of technological measures.
If you are interested in obtaining open source code for this product, please contact Mitsubishi at
(800) 332-2119. A nominal handling and mailing charge may apply.
For assistance call 1(800) 332-2119
Trademark and License Information
95
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each
copy an appropriate copyright notice; keep intact all notices stating that this License and any non-permissive terms added in accord with section 7 apply to the code;
keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the Program.
You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided
that you also meet all of these conditions:
a) The work must carry prominent notices stating that you modified it, and giving a relevant date.
b) The work must carry prominent notices stating that it is released under this License and any conditions added under section 7. This requirement modifies the
requirement in section 4 to “keep intact all notices”.
c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along with any
applicable section 7 additional terms, to the whole of the work, and all its parts, regardless of how they are packaged. This License gives no permission to license
the work in any other way, but it does not invalidate such permission if you have separately received it.
d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined
with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are
not used to limit the access or legal rights of the compilation’s users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not
cause this License to apply to the other parts of the aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable Corresponding Source
under the terms of this License, in one of these ways:
a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the Corresponding Source fixed on a
durable physical medium customarily used for software interchange.
b) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least three
years and valid for as long as you offer spare parts or customer support for that product model, to give anyone who possesses the object code either (1) a copy
of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a
network server at no charge.
c) Convey individual copies of the object code with a copy of the written offer to provide the Corresponding Source. This alternative is allowed only occasionally and
noncommercially, and only if you received the object code with such an offer, in accord with subsection 6b.
d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same
way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object code. If the place to
copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts the
Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these requirements.
e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and Corresponding Source of the work are being
offered to the general public at no charge under subsection 6d.
A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the
object code work.
A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes,
or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of
coverage. For a particular product received by a particular user, “normally used” refers to a typical or common use of that class of product, regardless of the status of
the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product regardless of
whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified versions
of a covered work in that User Product from a modified version of its Corresponding Source. The information must suffice to ensure that the continued functioning of the
modified object code is in no case prevented or interfered with solely because modification has been made.
If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the
right of possession and use of the User Product is transferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction is characterized), the
Corresponding Source conveyed under this section must be accompanied by the Installation Information. But this requirement does not apply if neither you nor any third
party retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates for a work that has been
modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when the modification itself
materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are
applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire Program remains governed by this License without
regard to the additional permissions.
When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. (Additional permissions
may be written to require their own removal in certain cases when you modify the work.) You may place additional permissions on material, added by you to a covered
work, for which you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement
the terms of this License with terms:
a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or
b) Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works containing
it; or
c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different from the
original version; or
d) Limiting the use for publicity purposes of names of licensors or authors of the material; or
e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or
f)
Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual assumptions of
liability to the recipient, for any liability that these contractual assumptions directly impose on those licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document contains a further
restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by the terms of that license document, provided
that the further restriction does not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or
a notice indicating where to find the applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above requirements apply either
way.
8. Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will
automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11).
For assistance call 1(800) 332-2119
96
Trademark and License Information
However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright holder
explicitly and finally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days
after the cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some reasonable means, this is
the first time you have received notice of violation of this License (for any work) from that copyright holder, and you cure the violation prior to 30 days after your receipt of
the notice.
Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this License. If your rights have
been terminated and not permanently reinstated, you do not qualify to receive new licenses for the same material under section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence
of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you permission to propagate
or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating a covered work, you indicate your
acceptance of this License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject to this
License. You are not responsible for enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations.
If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the
work the party’s predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the
predecessor in interest, if the predecessor has it or can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty,
or other charge for exercise of rights granted under this License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any
patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called
the contributor’s “contributor version”.
A contributor’s “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired, that would be
infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control” includes the right to grant patent sublicenses in a manner consistent
with the requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor’s essential patent claims, to make, use, sell, offer for sale,
import and otherwise run, modify and propagate the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to copy, free of charge and
under the terms of this License, through a publicly available network server or other readily accessible means, then you must either (1) cause the Corresponding Source
to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your
conveying the covered work in a country, or your recipient’s use of the covered work in a country, would infringe one or more identifiable patents in that country that you
have reason to believe are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a patent
license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent
license you grant is automatically extended to all recipients of the covered work and works based on it.
A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more
of the rights that are specifically granted under this License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the
business of distributing software, under which you make payment to the third party based on the extent of your activity of conveying the work, and under which the
third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent license (a) in connection with copies of the covered work
conveyed by you (or copies made from those copies), or (b) primarily for and in connection with specific products or compilations that contain the covered work, unless
you entered into that arrangement, or that patent license was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under
applicable patent law.
12. No Surrender of Others’ Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then
as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty for further conveying from those to whom you
convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU Affero
General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue to apply to the part which is the covered
work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction through a network will apply to the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit
to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General Public License “or any later version”
applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free Software Foundation.
If the Program does not specify a version number of the GNU General Public License, you may choose any version ever published by the Free Software Foundation.
If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy’s public statement of acceptance of a
version permanently authorizes you to choose that version for the Program.
Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of
your choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MODIFIES
AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply local law that
most closely approximates an absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of liability accompanies a copy of the
Program in return for a fee.
For assistance call 1(800) 332-2119
Trademark and License Information
97
GNU General Public License
Version 2, June 1991
Copyright (C) 1989, 1991
Free Software Foundation, Inc.
675 Mass Ave, Cambridge, MA 02139, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to
guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the
Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by
the GNU Library General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software
or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate
to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure
that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify
the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is
modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will
not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain
patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not
licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this
General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another
language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not
restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running
the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of
any warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed
as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the
most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying
that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License.
(Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print
an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works.
But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this
License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or
distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above
provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on
For assistance call 1(800) 332-2119
98
Trademark and License Information
a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing
source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for
noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the
source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code
from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights,
from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program
or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work
based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program
or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy,
distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights
granted herein. You are not responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on
you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If
you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not
distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly
or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as
a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has
the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made
generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/
donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who
places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in
or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you
have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program
does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission.
For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision
will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS”
WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS
OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE
WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
For assistance call 1(800) 332-2119
Warranty
99
Mitsubishi LCD Flat Panel HDTV Limited Warranty
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants to the original purchaser of this LCD Flat Panel HDTV
that if purchased from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of improper workmanship and/or material:
a. Parts. All parts (except any software incorporated into this HDTV) are warranted for a period of one year from the date of the
original purchase at retail. We will repair or replace, at our option, any defective part without charge for the part. Parts used for
replacement may be replaced with those of like kind and quality and may be new or remanufactured. Parts used for replacement are warranted for the remainder of the original warranty period.
b. Embedded Software. MDEA warrants that all software incorporated into this HDTV (the “Embedded Software”) will
perform in accordance with the functional description of Embedded Software in all material respects, but MDEA does not
warrant that the Embedded Software is error-free. The warranty contained in this section shall continue for a period of one
year, from the date of the original purchase from the authorized dealer. If, after prompt notice within the warranty period, MDEA
determines that the Embedded Software has failed to perform in accordance with such functional description in all material
respects and if such failure is not due to accident, misuse, modification or misapplication of the Embedded Software, then
MDEA shall modify or replace the nonconforming Embedded Software at no charge to you, which at MDEA’s sole discretion
may be fulfilled by means of modification or replacement software contained on a replacement memory card for Consumer
installation. The foregoing shall be MDEA’s sole obligation to you under this limited warranty. All rights under this limited warranty on the Embedded Software also subject to your compliance with the terms of the Software License Agreement applicable to this HDTV, and this limited warranty on the Embedded Software shall be null and void if the Embedded Software is
modified or changed in any manner except as specifically authorized by MDEA.
c. Labor. For certain items that are designed to be replaced by the consumer, including (but not limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all other parts, we will provide the labor for a
warranty repair by an authorized MITSUBISHI service center without charge for one year from the original date of purchase at
retail.
d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within the applicable warranty time period.
BEFORE REQUESTING SERVICE, please review the TV owner’s guide to insure proper installation and correct customer control adjustment. If the problem persists, please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center whose name and address can be obtained from your MITSUBISHI dealer, by writing to the address provided below, calling MDEA at 800-332-2119, or using the support feature of our
website at www.Mitsubishi-tv.com.
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your television is
located within the geographic territory customarily covered by an authorized MITSUBISHI service center. If not, you must either
deliver your television to an authorized service location at your own expense, or pay for any travel and/or transportation costs
the service center may charge to and from you home. Actual service labor will be provided without charge.
c. Proof of purchase from an authorized MITSUBISHI dealer is required when requesting warranty service. Present your sales
receipt or other document which establishes proof and date of purchase. THE RETURN OF THE OWNER REGISTRATION
CARD IS NOT A CONDITION OF WARRANTY COVERAGE. However, please return the Owner Registration Card so that we can
contact you should a question of safety arise which could affect you.
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b. Cosmetic damage or any other damage where such damage is caused by unauthorized modification, alteration, repairs to
or service of the product by anyone other than an authorized MITSUBISHI service center; physical abuse to or misuse of the
product (or any product damaged by excessive physical or electrical stress); any products that have had a serial number or any
part thereof altered, defaced or removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any
damage caused by acts of God or other factors beyond the reasonable control of MDEA, such as power surge damage caused
by electrical system or damages caused by use of third party mounting brackets or stands. This limited warranty also excludes
service calls where no defect in the product covered under this warranty is found, service calls related to unsatisfactory audio
or visual reception or signal unless caused by a defect in the product that is covered under this limited warranty, all costs,
expenses or any other damages arising from product installation, removal from or re-installation into custom installations or on
For assistance call 1(800) 332-2119
100
Warranty
wall mountings, or set-ups, any adjustments of user controls (including contrast, brightness, color, tint, fine tuning, sharpness),
other adjustment necessary to prepare the unit for display or use, connection with any external audio receiver, antenna, cable
or satellite systems, or service of products purchased or serviced outside the U.S.A. Please consult the operating instructions
contained in the Owner’s Guide furnished with the product for information regarding user controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION, MIGHT
ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY LIMITED TO A TERM OF
ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF
CONTRACT, OR OTHERWISE.
5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental,
special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
7. In the event of any dispute under this limited warranty, jurisdiction and venue for resolving that dispute will be in the state
where the television was purchased and the laws of such state will govern. In no event shall Mitsubishi have any liability, including with out limitation, for general, consequential, incidental, or special damages for loss, destruction, damage or corruption
of recorded data, media or software resulting from use of this television, or cost of recovery of lost data, media or software
therefore.
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618-1904
Network Service Disclaimer
Third party content and services, including without limitation home entertainment services by VUDU, Inc., are provided
in accordance with whatever terms and conditions are established by the third party providers and agreed to by you.
Mitsubishi Digital Electronics America (“MDEA”) has no control over any such third parties or any agreement you reach
with them. MDEA has no control over the networks or transmission facilities by which content and services are provided
by third parties. Your connection to the internet may vary in availability and quality. Customer service questions are to
be directed to the third-party provider, not MDEA.
MDEA DOES NOT WARRANT CONTENT OR SERVICES PROVIDED BY ANY THIRD PARTY, EITHER EXPRESSLY OR
IMPLIEDLY, FOR ANY PURPOSE. MDEA DOES NOT WARRANT THAT ANY THIRD PARTY SERVICE WILL REMAIN
AVAILABLE FOR ANY PERIOD OF TIME OR THAT IT WILL BE SATISFACTORY, UNINTERRUPTED OR ERROR FREE.
MDEA EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO, WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO ANY THIRD PARTY CONTENT
AND SERVICES.
MDEA WILL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE, WHETHER IN CONTRACT OR TORT OR OTHER
LEGAL THEORY, FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, ATTORNEY
FEES, EXPENSES, OR ANY OTHER DAMAGES ARISING OUT OF, OR IN CONNECTION WITH, YOUR USE OF ANY
CONTENT OR SERVICE THAT IS PROVIDED TO YOU BY ANY THIRD PARTY, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES.
For assistance call 1(800) 332-2119
Index
Index
A
Accent Lighting 54
Anamorphic Picture Format 33
Antenna Input (ANT) 23
Setting Up 14
Signal Strength for Digital Channels 31
Audio Lock (A/V receiver control) 74
Auto Input Sensing 15
Auto-Off (Sleep Timer) 29
Auto-On (Timer) 52
A/V Receiver
and TV’s Remote Control 73
Audio Lock 74
Center Channel 28
Connecting 23, 24, 27
Controlling Sound Volume 32
Disconnecting Analog 32
NetCommand IR Control 67, 68
Controlling a Device Connected
to the A/V Receiver 45, 71
Video and Audio Switching via
HDMI 70
B
Backlight 10, 47
Batteries 9
Blue Glow 54
Bluetooth Audio Playback 37
Brightness (picture adjustment) 47
C
Cable Box
and TV’s Remote Control 73
Connecting 25
Captions Menu 51
CD Player 36
CEC (Consumer Electronics Control)
8, 45, 81
A/V Receiver 32, 82
Troubleshooting 87
Center Channel 28
Channels
antennaweb.org 53
Favorites (Fav) 29
Physical/Virtual Channel Numbers 53
Scan (memorize) 14, 53
Troubleshooting 88
Tuning 16
ChannelView™ Channel Listings 30
Cleaning 84
Clock, Set Date and Time 52
Closed Captions 51
Color Adjustments
Menu Controls 47
Reset Color 48, 85
Computer 19, 20
Contrast 47
Control Panel 13
Control Panel Lock 13, 59
101
Internet 42
IR Emitter Placement 61
L
FAV (Favorite Channels) 29
Film Mode 47
FORMAT (picture shape) 18
Freeze Picture (PAUSE key) 11
Front Panel
Blue Glow Accent Lighting 54
Controls 13
Full Native 18, 33
Language
Changing the Menu Language
52
In Digital Programs 52
SAP (Second Audio Program) 50
Learn 55. See also NetCommand IR
Control
Letter Box Image Display 33
Level Sound 50
Light (front panel) 13
Listen To 50
Listings 30
Lock TV
Bypassing the Lock 79
Lock by Channel 59
Lock by Ratings 58
Lock by Time 59
Lock Control Panel 59
Preset V-Chip Blocking 57
G
M
D
Date. See Clock
Default Settings, Returning to 85
DIGITAL AUDIO OUTPUT 23
DVD Player
and TV’s Remote Control 73
Connecting 24, 25
DVI Device, Connecting 19, 25
F
Game
Game Picture Mode 46
HDMI Cables for Games 23
GUIDE Key
ChannelView 30
HDMI Control 83
NetCommand Control 64, 66
H
HD (High-Definition) Signal) 31
HDMI
Changing Out an HDMI Device
and Auto Input Sensing 15
Connecting an HDMI Device 19,
24
A/V Receiver with HDMI 27
HDMI Cable Types 23
HDMI Control of CEC Devices 81
HDMI Jack 23
Removing an HDMI Device from
the Activity Menu 55
Headphones 50
I
INFO Key
ChannelView 30
Status Display 31
INPUT Key/Input Selection Menu
Change Input Name 55
Choose Viewing Source 16
NetCommand-Controlled Switching of A/V Receiver Inputs 64
Removing a Disconnected HDMI
Device 55
Memorizing Channels 14, 53
Add Single Channel to Memory
53
MP3 Player (audio-only connection)
36
MUTE Key 11
N
NetCommand IR Control
About 60
A/V Receiver Control 68
Initial Setup for Most Devices 62
Operating 63
Troubleshooting 91
P
Pass Code
Resetting 79
Setting 57
VUDU Password 87
PerfectColor 48
Photo Viewing 35
Picture
Picture Menu Adjustments 46
Picture Quality and Film Mode
47
Shape (format) 18, 20, 33
Troubleshooting 89
Power On/Off
Troubleshooting 88
For assistance call 1(800) 332-2119
102
Index
R
Ratings (TV and Movie) 58
Remote Control
Keys and Functions 11
Programming Instructions 74
Reset 84
Reset
A/V Memory Reset (for the current input) 85
A/V Reset (for all inputs) 86
HDMI Auto Input Sensing 15
Pass Code 79
PerfectColor/PerfecTint 85
Remote Control 84
Remote Control Audio Lock 74
System Reset 13
TV Reset Comparison Guide 85
S
Safety Instructions 4, 5
SAP (second audio program) 50
Satellite Receiver
and the Remote Control 73
Connecting 19, 24, 25
Scan (memorize channels) 53
ScreenSaver 47
SD (Standard-Definition Signal) 31
Service and Support 85
Signal Definitions 31
Signal Strength Indicator 31
Sleep Timer 29
Sound
Controlling A/V Receiver Volume
(NetCommand) 68
U
USB Port 23
Auto Detection 15
File Types 34
Locations 22
USB Media Player Menu 35
Wireless Network Adapter 43
Wireless Subwoofer 28
V
V-Chip Ratings
Definitions 58
In Status Display 31
VCR
Connecting 26
Troubleshooting 89
Video from a Digital Camera 36
Video Game. See Game
VUDU Movie Service 44, 87
W
Wall-Mounting 7
Wireless Adapter 43
Audio Lock 74
Level Sound 50
Menu Adjustments 49
Sound Mode (audio effects) 50
Sound Projector 38
Standard-Definition Signal 31
Stand Installation 6
Status Display 31
Stereo System. See A/V Receiver
Stream TV 42
Subwoofer 28, 49, 50
Surround Sound
Rear Speakers 41
Simulated Surround Sound 50
Sound Projector 38
TV Audio Outputs 24
System Reset 13, 86
T
Time. See Clock
Timer (auto-on) 52
Time Zone. See Clock
Tools Menu 12
Troubleshooting 85
For assistance call 1(800) 332-2119
Website:
www.mitsubishi-tv.com
E-mail:
MDEAservice@mdea.com
For questions, call Consumer Relations at
800-332-2119
To order replacement or additional
remote controls,
Visit our website www.mitsuparts.com
or call
800-553-7278
SYSTEM RESET
If the TV does not respond to the remote control,
control-panel buttons, or will not power on/off, press
and hold the POWER button on the control panel for
ten seconds.
The TV will turn off. Power on the TV and the green LED
will flash quickly for about one minute. Recent settings
changes may be lost.
VLP43/VLP43+/VLP43+++
© 2010 Mitsubishi Digital Electronics America, Inc.
VLP43_IB_20100730