ENGLISH
OWNER’S MANUAL
MONITOR TV
Please read this manual carefully before operating
your set and retain it for future reference.
MONITOR TV MODELS
M197WDP
M227WDP
M237WDP
www.lge.com
PREPARATION
FRONT PANEL CONTROLS
■
This is a simplified representation of the front panel. The image shown may be somewhat different from your set.
INPUT
INPUT
Button
MENU
MENU
Button
OK
OK
Button
VOL
VOLUME
Buttons
PR
PROGRAMME
Buttons
Power
Button
Headphone
Jack
1
<M197WDP/M227WDP>
PREPARATION
BACK PANEL INFORMATION
■
This is a simplified representation of the back panel. The image shown may be somewhat different from your set.
1
2
3
4
AUDIO IN
(RGB/DVI)
5
6
COMPONENT
IN
OPTICAL
DIGITAL
AUDIO OUT
AV 2
AV
V1
AV
V2
VIDEO
PB
RGB IN (PC)
HDMI IN
AV 1
Y
PR
AC IN
DVI-D (PC)
ANTENNA/
CABLE IN
L
AC IN
7
1
2
3
2
RS-232C IN
(CONTROL & SERVICE)
8
9
PCMCIA (Personal Computer Memory Card
International Association) Card Slot
This feature is not available in all countries.
Power Cord Socket
This set operates on AC power. The voltage is indicated
on the Specifications page. Never attempt to operate
the set on DC power.
HDMI Input(Not Support PC)
Connect a HDMI signal to HDMI IN.
Or DVI (VIDEO) signal to HDMI IN with DVI to HDMI
cable.
4
RGB/DVI Audio Input
Connect the audio from a PC.
5
Optical Digital Audio Out
Connect digital audio from various types of eguipment.
6
RGB INPUT (PC)
Connect the output from a PC.
R
AUDIO
USB IN
11
10
12
7
USB IN
8
DVI-D Input
Connect the output from a PC.
9
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
10
Component Input
Connect a component video/audio device to these
jacks.
11
Euro Scart Socket (AV1/AV2)
Connect scart socket input or output from an external
device to these jacks.
12
Antenna Input
Connect over-the-air signals to this jack.
<M237WDP>
PREPARATION
BACK PANEL INFORMATION
■
This is a simplified representation of the back panel. The image shown may be somewhat different from your set.
1
2
3
4
AUDIO IN
(RGB/DVI)
5
6
COMPONENT
IN
OPTICAL
DIGITAL
AUDIO OUT
Y
HDMI IN
AVAV
2V
1
AV
V2
VIDEO
PB
RGB IN (PC)
AV 1
PR
AC IN
DVI-D (PC)
2
3
RS-232C IN
(CONTROL & SERVICE)
8
9
PCMCIA (Personal Computer Memory Card
International Association) Card Slot
This feature is not available in all countries.
Power Cord Socket
This set operates on AC power. The voltage is indicated
on the Specifications page. Never attempt to operate
the set on DC power.
HDMI Input(Not Support PC)
Connect a HDMI signal to HDMI IN.
Or DVI (VIDEO) signal to HDMI IN with DVI to HDMI
cable.
4
RGB/DVI Audio Input
Connect the audio from a PC.
5
Optical Digital Audio Out
Connect digital audio from various types of eguipment.
6
RGB INPUT (PC)
Connect the output from a PC.
R
AUDIO
AC IN
USB IN
7
1
ANTENNA/
CABLE IN
L
11
10
12
7
USB IN
8
DVI-D Input
Connect the output from a PC.
9
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
10
Component Input
Connect a component video/audio device to these
jacks.
11
Euro Scart Socket (AV1/AV2)
Connect scart socket input or output from an external
device to these jacks.
12
Antenna Input
Connect over-the-air signals to this jack.
3
PREPARATION
<M197WDP/M227WDP>
STAND INSTALLATION
■
The image shown may be somewhat different from your set.
1
Carefully place the product screen side down on a
cushioned surface that will protect product and
screen from damage.
2
Insert the s t a n d b a s e into the product
3
Attach the monitor to the Stand Base by turning
the screw to the right.
* Turn the screw by using the screw handle
Screw
4
PREPARATION
<M237WDP>
STAND INSTALLATION
■
The image shown may be somewhat different from your set.
1
Carefully place the product screen side down on a
cushioned surface that will protect product and
screen from damage.
2
Insert the s t a n d b a s e into the product
3
Attach the monitor to the Stand Base by turning
the screw to the right.
* Turn the screw by using the screw handle
Screw
5
<M197WDP/M227WDP>
PREPARATION
DETACHING STAND
■
The image shown may be somewhat different from your set.
1
Place the set screen side down on a cushion or
soft cloth.
2
Detach the monitor to the Stand Base by turning the screw to the left.
3
Turn the screw by using the screw handle
4
Pull the stand base.
5
6
<M237WDP>
PREPARATION
DETACHING STAND
■
The image shown may be somewhat different from your set.
1
Place the set screen side down on a cushion or
soft cloth.
2
Detach the monitor to the Stand Base by turning the screw to the left.
3
Turn the screw by using the screw handle
4
Pull the stand base.
5
7
PREPARATION
WALL MOUNT: HORIZONTAL INSTALLATION
For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installation
instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
10 cm
10 cm
10 cm
10 cm
10 cm
DESKTOP PEDESTAL INSTALLATION
For proper ventilation, allow a clearance of 10 cm on each side and from the wall.
10 cm
10 cm
10 cm
8
10 cm
PREPARATION
POSITIONING YOUR DISPLAY
■
The image shown may be somewhat different from your set.
Adjust the position of the panel in various ways for maximum comfort.
• Tilt range
-5°
-15°
LOCATION
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose
the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a position to allow a
free flow of air. Do not cover the ventilation openings on the back cover.
If you intend to mount the set to a wall, attach Wall mounting interface (optional parts) to the back of the set.
When you install the set using the wall mounting interface (optional parts), attach it carefully so it will not drop.
- Be sure to use screws and a wall mount that meet VESA standards.
- Using screws longer than those recommended might damage the product.
- Using screws that do not meet VESA standards might either damage the product or result in it coming away from the
wall. We will not be held responsible for any damage resulting from failure to follow these instructions.
< Screw Mounting Interface Dimension >
M197WDP/M227WDP : 100 mm x 100 mm hole spacing
M237WDP : 75 mm x 75 mm hole spacing
Warning:
When adjusting the angle of the screen,do not put your
finger(s)in between the head of the monitor and the stand
body.You can hurt your finger(s).
9
PREPARATION
KENSINGTON SECURITY SYSTEM
- The product is equipped with a Kensington Security System connector on the back panel. Connect the
Kensington Security System cable as shown below.
- For detailed installation and use of the Kensington Security System, refer to the user’s guide provided with the
Kensington Security System.
For further information, contact h t t p : / / w w w . k e n s i n g t o n . c o m, the internet homepage of the Kensington
company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and
LCD projectors.
NOTE
- The Kensington Security System is an optional accessory.
NOTES
a. If the product feels cold to the touch, there may be a small “flicker” when it is turned on.
This is normal, there is nothing wrong with product.
b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However,
they have no adverse effect on the monitor's performance.
c. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time.
Doing so may produce some temporary distortion effects on the screen.
<M197WDP/M227WDP>
10
<M237WDP>
EXTERNAL EQUIPMENT SETUP
■
To prevent equipment damage, never plug in any power cords until you have finished connecting all equipment.
ANTENNA CONNECTION
For optimum picture quality, adjust antenna direction.
■ An antenna cable and converter are not supplied.
■
Wall
Antenna
Socket
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
RF Coaxial Wire (75
Outdoor
Antenna
(VHF, UHF)
ANTENNA/
CABLE IN
)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
UHF
Antenna
Signal
Amplifier
ANTENNA/
CABLE IN
VHF
■
■
In poor signal areas, to get better picture quality, install a signal amplifier to the antenna as shown above.
If signal needs to be split for two TVs, use an antenna signal splitter for connection.
11
EXTERNAL EQUIPMENT SETUP
■
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
■
The image shown may be somewhat different from your set.
HD RECEIVER SETUP
When connecting with a component cable
1
Connect the SET-TOP outputs to the C O M P O N E N T I N
V I D E O sockets (Y PB PR) on the set.
2
Connect the audio cable from the SET-TOP to C O M P O N E N T I N A U D I O sockets of the set.
3
Press the I N P U T button to select C o m p o n e n t .
Signal
Component
HDMI
480i/576i
Yes
No
480p/576p
Yes
Yes
720p/1080i
Yes
Yes
1080p
Yes
Yes
COMPONENT
IN
Y
VIDEO
1
AUDIO
PB
2
PR
L
R
12
EXTERNAL EQUIPMENT SETUP
When connecting with a HDMI
1
HDMI IN
Connect the HDMI output of the digital set-top box to the
AV 1
AV 2
H D M I I N jack on the set.
1
When connecting with a HDMI to DVI cable
1
Connect the digital set-top box to H D M I I N jack on
the set.
2
Connect the audio output of the digital set-top box to
the A U D I O I N ( R G B / D V I ) jack on the set.
3
Turn on the digital set-top box. (Refer to the owner’s
manual for the digital set-top box.)
HDMI IN
AUDIO IN
(RGB/DVI)
2
1
AUDIO
DVI OUTPUT
L
R
! NOTE
G
HDMI Input does not support PC mode. If it is connected PC, the screen may not be displayed properly.
13
EXTERNAL EQUIPMENT SETUP
DVD SETUP
When connecting with a component cable
1
Connect the video output sockets (Y PB PR) of the DVD to
the C O M P O N E N T I N V I D E O sockets (Y PB PR) of the set.
2
Connect the audio cable from the DVD to C O M P O N E N T
I N A U D I O sockets of the set.
3
Press the I N P U T button to select C o m p o n e n t.
4
Press the P L A Y button on the DVD.
The DVD playback picture appears on the screen.
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the set
Video output ports
on DVD player
COMPONENT
IN
Y
VIDEO
1
AUDIO
PB
2
PR
L
R
14
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
EXTERNAL EQUIPMENT SETUP
When connecting with a Euro Scart[DVD]
1
AV 1
AV 2
Connect the Euro scart socket of the DVD to the Euro scart
socket of the set.
2
Press the I N P U T button to select A V 1.
If connected to A V 2 Euro scart socket, select A V 2 input
source.
3
Press the P L A Y button on the DVD.
The DVD playback picture appears on the screen.
1
(R)
AUDIO/
VIDEO
(L)
AUDIO
! NOTE
G
G
Signal type RGB, i.e. the signals red, green and blue can only be selected for the Euro scart and the AV 1 can be
received. These signals are transmitted, for example, by a paid TV decoder, game machine or photo CD unit, etc.
Please use shielded scart cable.
When connecting HDMI cable
1
HDMI IN
Connect the HDMI output of the DVD to the
H D M I I N jack on the set.
1
! NOTE
G Set can receive the video and audio signal simultaneously by using a HDMI cable.
G
If the DVD player does not support Auto HDMI, you need to set the DVD output resolution appropriately.
15
EXTERNAL EQUIPMENT SETUP
VCR SETUP
To avoid picture noise (interference), leave an adequate distance between the VCR and set.
■ Typically a still picture is shown on the VCR. If a user uses 4:3 picture format for a long time, an afterimage
may remain on the sides of the screen.
■
When connecting with an antenna
ANTENNA/
CABLE IN
ANT OUT
S-VIDEO
ANT IN
OUTPUT
SWITCH
L
VIDEO
R
1
Wall Jack
2
Antenna
1
Connect the RF out socket of the VCR to the aerial socket of the set.
2
Connect the aerial cable to the RF aerial in socket of the VCR.
3
Store the VCR channel on a desired programme number using the ‘Manual
programme tuning’ section.
4
Select the programme number where the VCR channel is stored.
5
Press the P L A Y button on the VCR.
AV 1
16
AV 2
EXTERNAL EQUIPMENT SETUP
USB SETUP
USB IN
1
Connect the USB device to the U S B I N jacks on the
side of set.
2
After connecting the U S B I N jacks, you use the U S B
function. (G p .86)
When connecting with a Euro Scart[VCR]
1
2
Connect the Euro scart socket of the VCR to the Euro
scart socket of the set.
Press the P L A Y button on the VCR.
If your VCR outputs an AV switching signal via the Scart
lead, the set will auto switch to A V 1 mode on start of
playback, but if you want to keep on watching in TV mode,
press the D / E or NUMBER buttons.
If connected to A V 2 Euro scart socket, select A V 2 input
source.
AV
V1
AV
V2
1
Otherwise press the I N P U T button on the remote control
handset to select A V 1. The VCR playback picture appears
on the screen.
(R)
You can also record programmes received by the set on
video tape.
AUDIO/
VIDEO
(L)
AUDIO
! NOTE
G
G
Signal type RGB, i.e. the signals red, green and blue can only be selected for the Euro scart and the AV 1
can be received. These signals are transmitted, for example, by a paid TV decoder, game machine or photo
CD unit, etc.
Please use shielded scart cable.
17
EXTERNAL EQUIPMENT SETUP
AV 1
AV 2
INSERTION OF CI MODULE
Insert the CI Module to P C M C I A (Personal Computer
Memory Card International Association) C A R D S L O T
of set as shown.
TV
1
PCMCIA
CARD SLOT
- To view the scrambled (paid) services in digital TV mode.
- This feature is not available in all countries.
1
For further information, see p. 37.
PC SETUP
This product provides Plug and Play capability, meaning that the PC adjusts automatically to the set's settings.
When connecting with a D-sub 15 pin cable
1
Connect the signal cable from the monitor output socket of
the PERSONAL COMPUTER to the PC input socket of the set.
2
Connect the audio cable from the PC to the A U D I O I N
( R G B / D V I ) sockets of the set.
3
Press the INPUT button to select R G B.
4
Switch on the PC, and the PC screen appears on the set.
The set can be operated as a PC monitor.
RGB IN (PC)
1
RGB OUTPUT
AUDIO IN
(RGB/DVI)
2
AUDIO
! NOTE
G
18
You must use shielded signal interface cables (D sub 15 pin cable, DVI cable) with ferrite cores to maintain
standard compliance for the product.
EXTERNAL EQUIPMENT SETUP
When connecting with a DVI cable
1
Connect the DVI output of the PC to the D V I - D I N
jack on the set.
2
Connect the audio cable from the PC to the A U D I O
I N ( R G B / D V I ) sockets of the set.
AUDIO IN
(RGB/DVI)
DVI-D (PC)
2
1
AUDIO
DVI OUTPUT
! NOTE
G If the set is cold, there may be a small “flicker” when the
set is switched on. This is normal, there is nothing wrong
with the set.
G If possible, use the 1360 x 768 @ 60 Hz video mode to
obtain the best image quality for your LCD monitor. If
used with other resolutions, some scaled or processed
pictures may appear on the screen. The set has been
preadjusted to the mode 1360 x 768 @ 60 Hz.
(M197WDP)
G If possible, use the 1920 x 1080 @ 60 Hz video mode
to obtain the best image quality for your LCD monitor. If
used with other resolutions, some scaled or processed
pictures may appear on the screen. The set has been
preadjusted to the mode 1920 x 1080 @ 60 Hz.
(M227WDP/M237WDP)
G Some
dot defects may appear on the screen, like Red,
Green or Blue spots. However, this will have no impact or
effect on the monitor performance.
G Do not press the LCD screen with your finger for a long
time as this may produce some temporary distortion
effects on the screen.
G Avoid keeping a fixed image on the set’s screen for prolonged periods of time. The fixed image may become
permanently imprinted on the screen; use a screen saver
when possible.
19
EXTERNAL EQUIPMENT SETUP
BACK COVER FOR WIRE ARRANGEMENT
<M197WDP/M227WDP>
Tie cables together with a cable management as
shown in the illustration.
Cable management
<M237WDP>
Tie cables together with a cable tie as shown in the
illustration.
Cable tie
20
EXTERNAL EQUIPMENT SETUP
RGB/DVI[PC]
<M227WDP/M237WDP>
<M197WDP>
Resolution
640x480
800x600
1024x768
1280x768
1280x800
1360x768
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
Resolution
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
31.469
37.500
37.879
46.875
48.363
60.123
47.776
60
75
60
75
60
75
60
720x400
49.306
47.712
60
60
31.468
31.469
37.500
37.879
46.875
48.363
60.123
67.500
63.981
79.976
64.674
65.290
75.000
66.587
70
60
75
60
75
60
75
75
60
75
60
60
60
60
640x480
800x600
1024x768
1152x864
1280x1024
1680x1050
1600x1200
1920x1080
HDMI[DTV] (Not Support PC)
Resolution
720x480/60p
720x576/50p
1280x720/50p
1280x720/60p
1920x1080/60i
1920x1080/50i
1920x1080/24p
1920x1080/30p
1920x1080/50p
1920x1080/60p
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
31.469
31.5
31.25
37.5
44.96
45
33.72
33.75
28.125
27
33.75
56.25
67.43
67.5
60
60
50
50
60
60
60
60
50
24
30
50
60
60
21
WATCHING TV /PROGRAMME CONTROL
REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the set.
TV/PC
POWER
1
INPUT
1
TV/RADIO TEXT
I/II
MUTE
POWER Switches the set on or off.
TV/PC Selects TV or PC mode.
2
INPUT External input mode rotates in regular sequence.
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
MENU
3
2
TV/RADIO Selects Radio or TV channel.
I/II Selects the sound output.(Refer to the p.68,69)
MUTE Switches the sound on or off.
EXIT
3
OK
4
0~9 number Selects a programme.
button Selects numbered items in a menu.
LIST Displays the programme table.(Refer to the p.38)
GUIDE
INFO i
Q.VIEW Returns to the previously viewed programme.
4
RETURN
*
VOL
PR
MENU Selects a menu. (Refer to the p.27)
5
EXIT Clears all on-screen displays.
FAV
INFO i Shows the present screen information.
Q.MENU
T.OPT
SUBTITLE
GUIDE Shows programme schedule.(Refer to the p.39~41)
MARK
THUMBSTICK Allows you to navigate the on-screen menus and adjust
(Up/Down/Left/Right) the system settings to your preference.
OK Accepts your selection or displays the current mode.
5
VOLUME UP Adjusts the volume.
/DOWN
RETURN Allows the user to move back one step in an interactive application, EPG or other user interaction function.
* No function
FAV Displays the selected favourite programme.(Refer to the p.38)
Programme Selects a programme.
UP/DOWN
22
WATCHING TV /PROGRAMME CONTROL
1
TV/PC
POWER
TV/RADIO TEXT
I/II
INPUT
TELETEXT These buttons are used for teletext.
BUTTONS For further details, see the ‘Teletext’ section.
(Refer to the p.94~96)
MUTE
1
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
MENU
2
USB Menu Controls USB menu (Photo List and Music List)
control buttons (Refer to the p.86)
3
EXIT
Q.MENU Select the desired quick menu source.
(Refer to the p.26)
MARK Check and un-check programmes in the recorded set
menu.
OK
GUIDE
INFO i
RETURN
*
VOL
PR
FAV
2
Q.MENU
T.OPT
SUBTITLE
MARK
3
Installing Batteries
■
Open the battery compartment cover on the back and install the batteries matching correct polarity (+ with +, - with -).
■
Install two 1.5 V AAA batteries. Don’t mix old or used batteries with new
ones.
■
Close cover.
To remove the batteries, perform the installation actions in reverse.
■
23
WATCHING TV /PROGRAMME CONTROL
TURNING ON THE TV
- When your TV is turned on, you will be able to use its features.
1
Firstly,connect the power cord correctly and check the main power( r / I )on the TV.
2
Set ID : Off
In standby mode to turn TV on, press the INPUT or PR D / E button on the TV or press the POWER button on the
remote control and the TV will switch on.
Set ID : On
In standby mode to turn TV on,pr ss the INPUT or PR D / E button on the TV or press the POWER, INPUT, PR D /
or NUMBER button on the remote control and the TV will switch on.
Initializing setup
If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust
the L a n g u a g e, M o d e S e t t i n g, C o u n t r y, A u t o t u n i n g.
Note:
a. If you close without completing the initial setting, the Initial Setting menu can be displayed again.
b. Press the RETURN button to change the current OSD to the previous OSD.
c. For those countries without confirmed DTV broadcasting standards, some DTV featur s might not work,
depending on the DTV broadcasting environment.
H o m e U s e” mode is the optimal setting for home environments, and is the TV's default mode.
d. "H
e. "SS t o r e D e m o"mode is the optimal setting for store environments. If a user modifies image quality data, “SS t o r e
D e m o” mode initializes the product to the image quality set by us after a certain period of time.
H o m e U s e, S t o r e D e m o) can be changed by executing M o d e S e t t i n g in the O P T I O N menu.
f. The mode (H
24
E
WATCHING TV /PROGRAMME CONTROL
PROGRAMME SELECTION
1
Press the P R + or - or NUMBER buttons to select a programme number.
TV/PC
POWER
TV/RADIO TEXT
VOLUME ADJUSTMENT
1
I/II
INPUT
MUTE
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
Press the VOL + or - button to adjust the volume.
If you want to switch the sound off, press the MUTE
button.
MENU
EXIT
OK
You can cancel this function by pressing the MUTE,
VOL + or - , or I/II button.
GUIDE
INFO i
RETURN
*
VOL
PR
FAV
Q.MENU
T.OPT
SUBTITLE
MARK
25
WATCHING TV /PROGRAMME CONTROL
QUICK MENU
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
Q.Menu (Quick Menu) is a menu of features which users might use frequently.
• A s p e c t R a t i o: Selects your desired picture format.
For Zoom Setting, select 14:9, Zoom and Cinema
Zoom in Ratio Menu. After completing Zoom Setting,
the display goes back to Q.Menu.
• P i c t u r e M o d e : Selects your desired Picture Mode.
• S o u n d M o d e : It is a feature to automatically set the
sound combination which it deems the best for the
images being watched. Selects your desired Sound
Mode.
• A u d i o : Selects the sound output.
• S l e e p T i m e r : Sets the sleep timer.
• U S B E j e c t : Selects “USB Eject” in order to eject USB
device.
Q.Menu
Aspect Ratio
16:9
Zoom Setting
Picture Mode
Standard
Sound Mode
Standard
Audio
L+R
Sleep Timer
Off
Eject
USB Eject
Close
1Q. MENU
Display each menu.
2
OK
or
Select your desired Source.
3
OK
• Press the RETURN button to move to the previous menu screen.
26
WATCHING TV /PROGRAMME CONTROL
ON SCREEN MENUS SELECTION AND ADJUSTMENT
Your set's OSD (On Screen Display) may differ slightly from what is shown in this manual.
SETUP
Move
PICTURE
OK
Move
AUDIO
OK
Move
Auto tuning
Aspect Ratio : 16:9
Auto Volume : Off
Manual tuning
Picture Mode : Vivid
Clear Voice II : Off
Programme Edit
• Backlight 100
Software Update : On
• Contrast 100
Balance
Diagnostics
• Brightness 50
Sound Mode : Standard
CI Information
• Sharpness 70
• Colour
60
• Tint
0
• Level
3
-
+
0
L
R
• SRS TruSurround XT : Off
R
G
• Treble
50
• Bass
50
E
E
TIME
OPTION
Move
Menu Language
: English
Audio Language
: English
OK
SETUP
PICTURE
AUDIO
OPTION
LOCK
INPUT
TIME
USB
Subtitle Language : English
Hard of Hearing(
)
: Off
Data Service
: MHEG
Country
: UK
Input Label
Key Lock
OK
Clock
Off Time
On Time
Sleep Timer
Auto Off
Move
OK
Move
OK
: Off
: Off
: Off
: On
: Off
E
LOCK
Move
Lock System
INPUT
OK
: Off
Move
OK
USB
Antenna
Photo List
Set Password
AV 1
Music List
Block Programme
AV 2
Parental Guidance : Off
Component
Input Block
RGB
HDMI
DVI
1MENU
Display each menu.
2
OK
Select a menu item.
3
OK
Move to the pop up menu.
• Press the MENU or EXIT button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
27
WATCHING TV /PROGRAMME CONTROL
AUTO PROGRAMME TUNING
Use this to automatically find and store all available programmes.
When you start auto programming in digital mode, all previously stored service information will be deleted.
SETUP
Move
SETUP
OK
A u t otuning
tuning
Auto
Manual tuning
Programme Edit
Software Update : On
Diagnostics
CI Information
1MENU
Move
A u t otuning
tuning
Auto
Manual tuning
Programme Edit
Software Update : On
Diagnostics
CI Information
Select S E T U P.
OK
All service-information will be updated.
Continue?
Yes
No
SECAM L Search
V Automatic Numbering
• Use NUMBER buttons to input a 4-digit
password in Lock System ‘On’.
2
• If you wish to keep on auto tuning, select
OK
Select A u t o T u n i n g.
OK
Select Y e s.
OK
Run Auto tuning.
YES using the F G button. Then, press the
OK button. Otherwise, select NO.
3
4
• Press the MENU or EXIT button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
28
WATCHING TV /PROGRAMME CONTROL
MANUAL PROGRAMME TUNING (IN DIGITAL MODE)
Manual Tuning lets you manually add a programme to your programme list.
SETUP
Move
SETUP
OK
Auto tuning
Manual
M a n u atuning
l tuning
Programme Edit
Software Update : On
Diagnostics
CI Information
Move
Auto tuning
Manual
M a n u atuning
l tuning
Programme Edit
Software Update : On
Diagnostics
CI Information
OK
F
DTV
G
Your receiver will add this
channel to your channel list.
UHF CH.
Bad
30
Normal
Good
Add
Close
1MENU
Select S E T U P.
• Use NUMBER buttons to input a 4-digit
password in Lock System ‘On’.
2
OK
Select M a n u a l T u n i n g.
OK
Select D T V.
3
4
Select the desired channel number.
• Press the MENU or EXIT button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
29
WATCHING TV /PROGRAMME CONTROL
MANUAL PROGRAMME TUNING (IN ANALOGUE MODE)
Manual Tuning lets you manually tune and arrange the stations in whatever order you desire.
SETUP
Move
SETUP
OK
Auto tuning
Manual
M a n u atuning
l tuning
Programme Edit
Software Update : On
Diagnostics
CI Information
Move
OK
Auto tuning
Manual
M a n u atuning
l tuning
Programme Edit
Software Update : On
Diagnostics
CI Information
TV
F
G
Storage
1
System
BG
Band
V/UHF
Channel
1
Search
Name
F G
C 01
Store
Close
1MENU
6
Select S E T U P.
Select V / U H F or C a b l e.
7
2
or
Select M a n u a l T u n i n g.
OK
1
2
3
4
5
6
7
8
9
Select the desired
channel number.
0
8
3
Start searching.
Select T V.
OK
4
or
1
2
3
4
5
6
7
8
9
0
9
Select the desired programme number on.
OK
Select S t o r e.
5
Select a TV system.
• Press the MENU or EXIT button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
• Use NUMBER buttons to input a 4-digit password in Lock System ‘On’.
• L: SECAM L/L’ (France)
BG: PAL B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M. East / Africa / Australia)
I: PAL I/II (U.K. / Ireland / Hong Kong / South Africa)
DK: PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)
• To store another channel, repeat steps 4 to 9.
30
WATCHING TV /PROGRAMME CONTROL
A
Assigning a station name
You can assign a station name with five characters to each programme number.
1MENU
5
Select SETUP.
OK
2
OK
Select Manual Tuning.
Select the position and make
your choice of the second
character, and so on.
You can use the alphabet A to
Z , the number 0 to 9 , +/ -, and
space.
6
3
OK
OK
Select Close.
OK
Select Store.
Select TV.
7
4
Select Name.
• Press the MENU or EXIT button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
31
WATCHING TV /PROGRAMME CONTROL
PROGRAMME EDIT
When a programme number is skipped, it means that you will be unable to select it using PR + / - button during
TV viewing.
If you wish to select the skipped programme, directly enter the programme number with the NUMBER buttons or
select it in the Programme edit menu
This function enables you to skip the stored programmes.
In some countries, it is possible to move a programme number by using the YELLOW button only.
1
SETUP
Move
YLE TV1
OK
Auto tuning
Manual tuning
Programme
P r o g r a m mEdit
e Edit
Software Update : On
Diagnostics
CI Information
DTV
RADIO
1 YLE TV1
2 YLE TV2
4 TV4 Stockholm
5 YLE FST
6 CNN
8 YLE24
9 YLE Teema
Favourite List
TV
14 TV4 Film
24 TV4 Fakta
50 TV400
24 TV4 Fakta
84 Kanal Lokal
24 TV4 Fakta
86 Info/3sat
87 Doku/Kika
88 TVE 1
E
FAV
Favourite
Pr. Change
D
F G Navigation
E
P
Page Change
RETURN Previous
Skip
1MENU
Select S E T U P.
• Use NUMBER buttons to input a 4-digit
password in Lock System ‘On’.
2
OK
Select P r o g r a m m e E d i t.
3
OK
Enter the Programme Edit.
4
Select a programme to be stored or skipped.
• Press the MENU or EXIT button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
32
WATCHING TV /PROGRAMME CONTROL
IN DTV/RADIO MODE
A
Skipping a programme number
1
Select a programme number to be skipped.
2
BLUE
Turn the skipped programme number to blue.
3
BLUE
A
• When a programme number is skipped, it means
that you will be unable to select it using the PR
+ / - button during normal TV viewing.
• If you wish to select a skipped programme, directly
enter the programme number with the NUMBER
buttons or select it in the programme edit or EPG.
Release the skipped programme.
Selecting favourite programme
1
FAV
Select your favourite programme number.
• It will automatically include the selected
programme into your favourite programme list.
33
WATCHING TV /PROGRAMME CONTROL
IN TV MODE
This function enables you to delete or skip the stored programmes.
You can also move some channels to other programme numbers.
A
Auto Sort
1
GREEN
Start Auto Sort.
• After activating Auto Sort once, you can no longer
edit programmes.
Deleting a programme
A
1
Select a programme number to be deleted.
• The selected programme is deleted, all the fol-
lowing programmes are shifted up one
2
RED
Turn the deleted programme number to red.
RED
Release the deleted programme.
3
A
Moving a programme
1
Select a programme number to be moved.
2
Turn the moved programme number to YELLOW.
YELLOW
3
YELLOW
A
Release the moved programme.
Skipping a programme number
1
Select a programme number to be skipped.
2
BLUE
Turn the skipped programme number to blue.
3
BLUE
A
that you will be unable to select it using the
PR + / - button during normal TV viewing.
• If you wish to select a skipped programme, directly
enter the programme number with the NUMBER buttons or select it in the programme edit or EPG.
Release the skipped programme.
Selecting a Favourite Programme
1
FAV
34
• When a programme number is skipped it means
Select your favourite programme number.
• The selected programme will be added to the
favourite programme list.
WATCHING TV /PROGRAMME CONTROL
SOFTWARE UPDATE
Software Update means software can be downloaded through the digital terrestrial broadcasting system.
SETUP
Move
SETUP
OK
Move
Auto tuning
Manual tuning
Programme Edit
S o f t w a rUpdate
e U p d a: tOn
e : On
Software
Auto tuning
Manual tuning
Programme Edit
S o f t w a rUpdate
e U p d a: tOn
e : OO
n ff
Software
Diagnostics
CI Information
Diagnostics
CI Information
3
1MENU
Select S E T U P.
Select S o f t w a r e U p d a t e.
On
On
Select O n or O f f.
• If you select On, a user
confirm message box will be
displayed to notify that new
software is found.
OK
2
OK
OK
4
OK
Save.
* When setting “Software Update”
Occasionally, a transmission of
updated digital software information will result in the following menu on the TV screen.
?
Software update is available.
Do you want to download?
(Ver. 02.54.00)
Your TV software is updated when you turn off
the TV using the remote control or local key.
Yes
i
Turning on the TV will stop the
update. Do you want stop?
Updating software
(Ver. 02.33.00) G
The new software is updated at
the time below.
(Ver. 02.54.00)
After Software Update is completed, the System takes about
one minute to restart.
The update is completed.
TV will be rebooted.
i
i
Close
(Ver. 02.54.00)
7%
Yes
No
Simple Update :for current
update stream
?
Select the Y E S using the F G
button and when you see the
following picture.
No
When the power is turned off, downloading starts.
When the power is turned on while updating, the
Open as PDF
Similar pages