Philips Wireless HD AV Connect SWW1810

Register your product and get support at
www.philips.com/welcome
SWW1810
EN User manual
3
1Important Safety 4
4
2 Your Wireless HD AV Connect What is in the box 6
6
3Overview 7
7
7
8
4Installation 9
The transmitter The receiver The remote control English
Contents
Connect the transmitter to your HD devices 9
Connect the receiver to the HDTV set 9
Connect the IR blaster and IR sensor
extender cables 10
Install remote control batteries 10
5 Activate your Wireless HD AV
Connect and set up the link Turn on the power of your HDTV Activate the wireless link 6 Mount your receiver Mount your receiver on the wall Mount your receiver on the back of the
HDTV 11
11
12
13
13
14
7 Technical data 15
15
15
8Notice 16
16
16
17
17
17
9 Frequently asked question 18
Supported resolution Product specifications Notice for USA Notice for Canada Recycling Disposal of your old product and batteries One Year Limited Warranty EN
3
1Important
e Do not use this apparatus near water.
Safety
g Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
f Clean only with dry cloth.
h Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
This ‘bolt of lightning’ indicates uninsulated
material within your unit may cause an electrical
shock.
The ‘exclamation mark’ calls attention to
features for which you should read the enclosed
literature closely to prevent operating and
maintenance problems.
i Do not defeat the safety purpose of
the polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third prong
are provided for your safety. If the provided
plug does not fit into your outlet, consult
an electrician for replacement of the
obsolete outlet.
Warning
•• To reduce the risk of fire or electric shock, this
apparatus should not be exposed to rain or moisture
and objects filled with liquids, such as vases, should not
be placed on this apparatus.
Caution
•• To prevent electric shock, fully insert the plug. (For
regions with polarized plugs: To prevent electric shock,
match wide blade to wide slot.)
Important Safety Instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
4
EN
j Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
k Only use attachments/accessories specified
by the manufacturer..
l Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
m Unplug this apparatus during lightning
storms or when unused for long periods of
time.
English
n Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
o Battery usage CAUTION – To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
unit:
• Do not mix batteries (old and new or
carbon and alkaline, etc.).
• Remove batteries when the unit is not
used for a long time.
p Apparatus shall not be exposed to
dripping or splashing.
q Do not place any sources of danger on the
apparatus (e.g. liquid filled objects, lighted
candles).
Warning
•• Use only the provided power adapter.
EN
5
2 Your Wireless
HD AV Connect
Congratulations on your purchase and welcome
to Philips!
To fully benefit from the support that Philips
offers, register your product at www.philips.
com/welcome.
HDMI cable
IR blaster extender cable
What is in the box
Note
•• Make sure you have all these items in the box. Contact
your dealer for any missing or damaged items.
Power adapter for the transmitter and receiver
x2
IR sensor extender cable
Transmitter
Anchors x 2
Screws x 2
Quick Installation Guide
Receiver
Adhesive tape x 2
User manual
Remote control
6
EN
Quick start guide
The receiver
English
3Overview
Top view
The transmitter
Front view
1
1
2
3
Source LEDs It displays the current
source input.
SOURCE
Press to switch the
button
source input of the
transmitter.
Power button Press to turn the
with the LED transmitter on/off
indicator
2
3
Source LEDs Indicators for HDMI1
and HDMI2
Press to turn the receiver
Power
button with on/off.
the LED
indicator
Source
Press to select the
button
source input.
Rear view
Rear view
1
POWER
DC IN jack Connect the power
adapter of the transmitter.
2 & 3 HDMI IN Connect the HD audio/
adapters
video device with the
HDMI cables.
Plug in the IR blaster
4
IR OUT
extender cable.
blaster
extender
jack
1
2
3
DC IN
jack
HDMI
OUT
adapter
IR IN jack
Connect the power adapter
of the receiver.
Connect the HDTV with an
HDMI cable.
Plug in the IR sensor
extender cable.
EN
7
The remote control
POWER Press to turn the
button
transmitter and receiver
on/off.
INFO
Displays on the HDTV
button
the connection status of
the receiver.
IR
Press to switch the IR
button
blaster frequency to meet
the requirement of the
source device.
SOURCE Press to switch the
button
audio/video source
inputs connected to the
transmitter.
1
2
3
4
The Wireless HD AV Connect gives you a total
wireless solution to place your HDTV set or
projector anywhere you want. The transmitter
can transmit uncompressed video content
over 65 feet (19.7 meters) without latency. The
receiver can receive signals for viewing on your
HDTV. All you need to do is to:
• Connect the transmitter to your HD
devices. Examples of HD devices are cable/
satellite box, Blu-Ray/HD DVD player, game
console or computer.
Note
•• These devices must have an HDMI port..
•
•
Connect the receiver to your HDTV set.
Control the transmitter with the remote
control.
8
EN
2
Connect the transmitter to
your HD devices
You can connect two audio/video sources to
the transmitter at the same time, but only one
source can be selected and played.
Connect the supplied power adapter to
the transmitter.
• Connect one end of the power
adapter to the DC IN jack of the
transmitter.
• Connect the other end of the power
adapter to a power outlet.
»» The power button of the transmitter
is lit in solid blue and turns red in
standby mode.
English
4Installation
Connect the receiver to the
HDTV set
HDMI OUT
IR IN
DC 5V
2
1
1
Connect the audio/video source to the
transmitter using the supplied HDMI cable.
• Connect one end of the HDMI cable
to the HDMI IN connector of the
transmitter.
HDMI IN
1
Note
•• There are two HDMI IN ports but only one HDMI
cable is supplied. To connect two audio/video sources
to the transmitter at the same time, you need an
additional HDMI cable.
•
Connect the other end of the HDMI
cable to the HDMI OUT connector of
the video source.
2
Connect the receiver with an additional
HDMI cable (not supplied):
• Connect one end of the HDMI cable
to the receiver.
• Connect the other end to the HDMI
IN connector of your HDTV.
Connect the supplied power adapter to
the receiver:
• Connect one end of the power
adapter to the DC IN jack of the
receiver.
• Connect the other end of the power
adapter to a power outlet.
»» The power button of the receiver is lit
in solid blue and turns red in standby
mode.
EN
9
Connect the IR blaster and IR
sensor extender cables
5
Extend and stick the IR sensor extender
cable onto the front side of your HDTV.
Note
Tip
•• If you cannot use the remote control of your device,
•• The IR blaster support 47KHz remote signal protocol,
while the IR sensor supports 36KHz - 56KHz (NEC,
RC5, RC6) remote signal protocol.
follow the steps in this section to connect the sensor
extender cables .
Install remote control
batteries
Caution
•• Risk of explosion! Keep batteries away from heat,
sunshine or fire. Never discard batteries in fire.
•• Risk of decreased battery life! Never mix different
brands or types of batteries.
•• Risk of product damage! When the remote control is
1
2
3
4
10
Plug the IR blaster extender cable into
the IR OUT blaster extender jack of the
transmitter.
Extend and stick the IR blaster extender
cable onto the front panel of the HD
device.
After the IR blaster extender cable is
connected to the transmitter, you can
control your HD device with the remote
control. Make sure that the remote control
points to the receiver.
If the distance between the receiver and
receiver has obstruction (e.g. the receiver
is mounted at the back of the HDTV), plug
the IR sensor extender cable into the IR
IN jack of the receiver.
EN
AAA
Connect the infrared blaster or sensor extender
cables if necessary.
1
2
3
AAA
not used for long periods, remove the batteries.
Open the battery compartment.
Insert two AAA batteries with correct
polarity (+/-) as indicated.
Close the battery compartment.
Turn on the power of your
HDTV
HDMI OUT
IR IN
DC 5V
HDM I
On screen display on HDTV
On screen
display
English
5 Activate your
Wireless HD AV
Connect and set
up the link
Mode and status
Standby mode: it is a powersaving mode
.....
Start up in progress: It takes 1520 seconds.
x and .... Searching available channels: It
occurs when the link cannot
establish over 80 seconds after
initialization.
HDMI On mode with unrecognized
CH1
video format
HDMI On mode but without input
CH1
from the source device
HDMI On mode with recognized video
CH1 1080P format
HDM I
1
2
Go to the source menu under the settings
menu of your HDTV.
Select the HDMI input to which the
receiver is connected.
EN
11
Activate the wireless link
Switch on the transmitter and receiver
In standby mode, a red power LED displays on
the transmitter and receiver.You can then turn on
the transmitter and receiver in the following ways:
Select the source on the transmitter
Press the source buttons on the remote
control, transmitter or receiver until you see the
available video from your device.
Tip
•• For information on the LED indicator status, see the
section on ‘LED indicator status of the transmitter’.
LED indicator status of the
transmitter and receiver
•
Press on the remote control.
»» Both the transmitter and receiver are
turned on.
Power
LED
Solid
red
Flashing
blue
Flashing
blue
Solid
blue
Solid
blue
Solid
blue
•
Press
on the transmitter and receiver.
Establish the link between the
transmitter and receiver
A flashing blue power LED displays until
the signal link between the two units are
established. Normally, it takes around 15-20
seconds for the link to establish successfully.
12
EN
Source Mode and status
LED
Off
Standby mode: it is a
power-saving mode
Flashing Start up in progress: It takes
blue
15-20 seconds.
Flashing Searching available channels:
It occurs when the link
cannot establish over 80
seconds after initialization.
Flashing On mode but without
quickly input from the source
device
Flashing On mode with
slowly unrecognized video format
Solid
On mode with recognized
blue
video format
Note
•• If the link is not established after 80 seconds, move the
transmitter, receiver and HDTV closer to each other.
The maximum transmission range is up to 65 feet (19.7
meters).
•• If more than one set of Philips Wireless HD AV Connect
is placed in the same room, make sure that the minimum
distance among each one is 6 feet 6 inches (2 meters).
•• If using a computer, make sure the video format is
supported before the video is displayed, see the
chapter on ‘Technical data’ for information.
•• If using a computer, and the picture on your TV is
not full screen, see the chapter on ‘Frequently asked
questions’ for information.
5
Hook the key holes at the back of the
receiver on the screws.
English
6 Mount your
receiver
You can either mount the receiver on the wall
or on the back of the HDTV.
Mount your receiver on the
wall
1
2
3
4
Select a spot near the HDTV.
Drill two holes in the wall. Make sure that
the distance between the two holes is
1 25/32” (45 mm) and the diameter of the
hole is 3/16” (5 mm).
Punch the supplied two anchors into the
two holes on the wall.
Put the two screws into the anchors and
leave 1/8” (3 mm) to mount the receiver on.
EN
13
Mount your receiver on the
back of the HDTV
1
2
Remove the white protective film from
one of the supplied adhesive tapes.
Secure the glued side of the adhesive tape
and attach it to the central bottom area of
the receiver.
6
Align the adhesive tape on the receiver
with the one on the HDTV until both the
receiver and HDTV are mounted together
firmly.
Note
•• The use of adhesive tapes is an alternative mounting
option when the receiver cannot be fixed.
•• When you mount the receiver at the back of the
HDTV, avoid blocking the ventilation holes of the
HDTV.
•• For safety reason, check regularly if the HDTV and
receiver are mounted together firmly.
•• The receiver is not recommended for in-the-wall
installation.
3
4
5
14
Select a flat location on the rear side of
the HDTV.
Remove the white protective film from the
other adhesive tape.
Secure the glued side of the adhesive tape
and attach it to the selected rear side of
the HDTV.
EN
Supported resolution
Power supply:
Input: AC 100~ 240V
Output: DC 5V, 2A
Operating temperature:
0~40°C/32~104°F
Video format
timings
Resolution
Transmitter interfaces
Primary CEA
video timing
480p
480p
480p
576p
720p
720p
1080i
1080i
1080p/60
1080p/60
-
A/V interfaces
HDMI input: Two (Type A)
Control signal interfaces
IR blaster extender: 2.5mm jack
Power interface
Power input: 5V DC jack
Switches
Top power switch: One
Top source switch: One
LEDs
Power LED: 1 x blue/red LED
Source LED: 2 x blue LED
Dimensions
194.8 x 146.8 x 31 mm (W x L x H)
Secondary CEA
video timing
1080p/24
1080p/24
1080p/24
640x480p @ 59.94/60Hz
720x480p @ 59.94Hz
720x480p @ 60Hz
720x576p @ 50Hz
1280x720p @ 50Hz
1280x720p @ 59.94/60Hz
1920x1080i @ 50Hz
1920x1080i @ 59.94/60Hz
1920x1080p @ 50Hz
1920x1080p @ 59.94/60Hz
1920x1080p @ 23.98/24Hz
1920x1080p @ 25Hz
1920x1080p @ 29.97/30Hz
Product specifications
General specification
Video resolution
HDMI input: 1080p, 1080i, 720p, 576p, 480p
Supported audio formats:
Digital audio: up to 6 Mbps AC3 and DTS
Analog audio: 32-96 KHz and 16-24 bits per
audio sample
Transmission distance:
Maximum 65 feet (19.7 meters)
Antennas:
High performance internal antennas
Operating frequencies:
5.15-5.25/5.725-5.825 GHz
English
7 Technical data
Receiver interfaces
A/V interfaces
HDMI output: One (Type A)
Control signal interfaces
IR sensor: available
Power interface
Power input: 5V DC jack
Switches
Top power switch: One
Top source switch: One
LEDs
Power LED: 1 x blue/red LED
Source LED: 2 x blue LED
Signal quality status: On-screen display
Dimensions
194.8 x 146.8 x 31 mm (W x L x H)
EN
15
8Notice
Notice for USA
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference
by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
FCC Caution: Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate this equipment.
• Operations in the 5.15-5.25GHz / 5.7255.825GHz band are restricted to indoor
usage only.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
16
EN
IMPORTANT NOTE:
Radiation Exposure Statement:
• This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment. This equipment
should be installed and operated with
minimum distance 20cm between the
radiator & your body.
• This transmitter must not be co-located
or operating in conjunction with any other
antenna or transmitter.
Note
•• The country code selection is for non-US model only
and is not available to all US model. Per FCC regulation,
all wireless product marketed in US must fixed to US
operation channels only.
Notice for Canada
This device complies with RSS-210 of the
Industry Canada Rules. Operation is subject to
the following two conditions: (1) This device
may not cause harmful interference, and (2) this
device must accept any interference received,
including interference that may cause undesired
operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed
and operated with minimum distance 20cm
between the radiator & your body.
Caution
•• The device for operation in the band 5150-5250 MHz is
only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems;
•• the maximum antenna gain permitted for devices in the
band 5725-5825 MHz shall comply with the e.i.r.p. limits
specified for point-to-point and non point-to-point
operation as appropriate.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products. The correct
disposal of your old product helps prevent
potentially negative consequences on the
environment and human health.
The packaging of this product is intended to
be recycled. Contact your local authorities for
information about how to recycle the packaging.
When this logo is attached to a product, it
means a financial contribution has been paid to
the associated national recovery and recycling
system.
Disposal of your old product
and batteries
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products and batteries.
The correct disposal of these products helps
prevent potentially negative consequences on
the environment and human health.
Your product contains batteries, which cannot
be disposed of with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries. The correct
disposal of batteries helps prevent potentially
negative consequences on the environment and
human health.
Please visit www.recycle.philips.com for
additional information on a recycling center in
your area.
HDMI, and HDMI logo, and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI licensing LLC in
the United States and other countries.
One Year Limited Warranty
Philips warrants that this product shall be free
from defects in material, workmanship and
assembly, under normal use, in accordance with
the specifications and warnings, for a period
of one year from the date of purchase. This
warranty extends only to the original purchaser
of the product, and is not transferable. To
exercise your rights under this warranty, you
must provide proof of purchase in the form of
an original sales receipt that shows the product
name and the date of purchase. For customer
support or to obtain warranty service, please
visit our website www.philips.com/support,
or dial in 1-888-744-5477. THERE ARE NO
OTHER EXPRESS OR IMPLIED WARRANTIES.
Philips’ liability is limited to repair or, at its
sole option, replacement of the product.
Incidental, special and consequential damages
are disclaimed where permitted by law. This
warranty gives you specific legal rights. You may
also have other rights that vary from state to
state.
EN
17
English
Recycling
9 Frequently asked question
The power LED on the
receiver is not lit up in red in
standby mode.
The computer screen image is
not full screen on my TV.
••
1
2
3
4
5
6
There is no video displayed on ••
my TV screen.
••
••
18
EN
Make sure that there is power supply for the transmitter and
receiver.
Right-click on an open space on your desktop.
Select Graphics Options > Output to > Digital Television (Now
the laptop image will only appear on your TV).
Once again, right-click on an open space on your desktop.
Select Screen Resolution.
On the pop-up box increase the resolution settings till the laptop
image better fits your TV screen.
Select OK and KEEP CHANGES when you are satisfied with
your image size..
Make sure that the appropriate cables are selected and inserted
to the transmitter, receiver, and HDTV.
Make sure that you select HDMI as the input source on your
HDTV.
Check the power LED and SOURCE LED on the receiver:
• Flashing blue power LED: Make sure that the transmission
range between receiver and transmitter is not over 65 feet
(19.7 meters) transmission distance. Move the transmitter
closer to the receiver.
• Solid blue power LED + slow and flashing source LED:1)
Make sure that the frame rate and video resolution of your
source device equipment are supported and conformed to
the technical specification. 2) Connect the source device to
your TV with an HDMI cable to check the compatibility of
the video format. 3) Make sure that the video solution your
source device is supported (See the chapter ‘Technical data’).
• Solid blue power LED + quick and flashing source LED: 1)
Make sure that the proper cables are connected among the
transmitter, receiver and HDTV. 2) Make sure that the source
devices connected to the transmitter are powered on.
••
••
Make sure that the video resolution of your source device
matches the resolution of your HDTV.
Make sure that the transmission range between receiver and
transmitter is not over 65 feet (19.7 meters) transmission
distance.
English
If the picture quality is poor,
what do I do?
Tip
•• For information, see the chapter on ‘Technical data’.
I cannot hear any sound or the ••
sound is poor, what do I do? ••
••
••
Make sure that the TV volume is adjusted correctly.
Make sure that the TV volume is not set to minimum or the
sound is not muted.
Make sure that the audio format is supported.
Make sure the HDMI cable of the transmitter is connected
correctly.
Tip
•• For information, see the chapter on ‘Technical data, section ‘Product specification’.
I cannot control the source
device with the IR blaster.
••
••
Make sure that the IR blaster and IR sensor extender cables are
facing the IR lens of the HD device.
Press the IR button on the remote control to change the IR
blaster frequency based on the requirement of the source device.
Tip
•• For information, see the chapter ‘Installation’, section ‘Connect to IR blaster and IR
sensor extender cables’.
EN
19
20
EN
21
© 2011 Koninklijke Philips Electronics N.V.
All rights reserved.
IFU_SWW1810_EN_V2.0
WK11485