BDL3245E
BDL4245E
BDL4645E
www.philips.com/welcome
User Manual (English)
BDL3245E / BDL4245E / BDL4645E
Safety Instructions
Warnings and Precautions
KNOW THESE SAFETY SYMBOLS
CAUTION:
O REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
T
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.
This symbol alerts you that important literature concerning operation and maintenance has been included with this product.
Note to CATV system installer: This reminder is provided to call CATV system installer’s attention to Article 820-40 of the National Electrical Code (Section
54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected
to the grounding system of the building as close to the point of cable entry as practical.
CAUTION:
FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user’s authority to operate it.
CAUTION:
To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug.
IMPORTANT: O
ne Federal Court has held that unauthorized recording of copyrighted TV programs is an infringement of U.S. copyright laws. Certain
Canadian programs may also be copyrighted and any unauthorized recording in whole or in part may be in violation of these rights.
TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
The Socket-outlet shall be installed near the apparatus and shall be easily accessible.
Read and follow these instructions when connecting and using your computer monitor:
• Unplug the monitor if you are not going to use it for an extensive period of time.
• Unplug the monitor if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is
off. However, never use alcohol, solvents or ammonia-based liquids.
• Consult a service technician if the monitor does not operate normally when you have followed the instructions in this manual.
• The casing cover should be opened only by qualified service personnel.
• Keep the monitor out of direct sunlight and away from stoves or any other heat source.
• Remove any object that could fall into the vents or prevent proper cooling of the monitor’s electronics.
• Do not block the ventilation holes on the cabinet.
• Keep the monitor dry. To avoid electric shock, do not expose it to rain or excessive moisture.
• If turning off the monitor by detaching power cable or DC power cord, wait for 6 seconds before attach the power cable or DC
power cord for normal operation.
• To avoid the risk of shock or permanent damage to the set do not expose the monitor to rain or excessive moisture.
• When positioning the monitor, make sure the power plug and outlet are easily accessible.
• IMPORTANT: Always activate a screen saver program during your application. If a still image in high contrast remains on the
screen for an extended period of time, it may leave an ‘after-image’ or ‘ghost image’ on the front of the screen. This is a well-known
phenomenon that is caused by the shortcomings inherent in the LCD technology. In most cases the afterimage will disappear
gradually over a period of time after the power has been switched off. Be aware that the after-image symptom cannot be repaired
and is not covered under warranty.
ii
BDL3245E / BDL4245E / BDL4645E
Regulatory Information
CE Declaration of Conformity
MMD declare under our responsibility that the product is in conformity with the following standards
• EN60950-1:2006+A11:2009 (Safety requirement of Information Technology Equipment)
• EN55022:2006+A1:2007 (Radio Disturbance requirement of Information Technology Equipment)
• EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment)
• EN61000-3-2:2006 (Limits for Harmonic Current Emission)
• EN61000-3-3:2008 (Limitation of Voltage Fluctuation and Flicker) following provisions of directives applicable
• 2006/95/EC (Low Voltage Directive)
• 2004/108/EC (EMC Directive)
• 2005/32/EC (EuP, Energy-using Product Directive) EC No. 642/2009 Implementing
• 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on ISO9000 level.
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE- CAUSING EQUIPMENT REGULATIONS.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
iii
BDL3245E / BDL4245E / BDL4645E
Polish Center for Testing and Certification Notice
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer,
monitor, printer, and so on) should have the same power supply source.
The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value
no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the
equipment and easily accessible.
A protection mark “B” confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/
E-06251.
Electric, Magnetic and Electronmagnetic Fields (“EMF”)
1. MMD manufactures and sells many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive
electromagnetic signals.
2. One of MMDs’ leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal
requirements and to stay well within the EMF standards applicable at the time of producing the products.
3. MMD is committed to develop, produce and market products that cause no adverse health effects.
4. MMD confirms that if its products are handled properly for their intended use, they are safe to use according to scientific evidence available today.
5. MMD plays an active role in the development of international EMF and safety standards, enabling MMD to anticipate further developments in
standardization for early integration in its products.
iv
BDL3245E / BDL4245E / BDL4645E
Information for U.K. only
WARNING - THIS APPLIANCE MUST BE EARTHED.
(B)
Important:
(A)
This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug
proceed as follows:
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin
plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse
at the distribution board should not be greater than 5A.
NOTE:
he severed plug must be destroyed to avoid a possible shock hazard should it be inserted
T
into a 13A socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured in accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN & YELLOW - “EARTH” (“E”)
1. The GREEN & YELLOW wire must be connected to the terminal in the plug which is marked with
the letter “E” or by the Earth symbol or coloured GREEN or GREEN & YELLOW.
2. The BLUE wire must be connected to the terminal which is marked with the letter “N” or coloured
BLACK.
3. The BROWN wire must be connected to the terminal which marked with the letter “L” or
coloured RED.
Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead
- not simply over the three wires.
v
BDL3245E / BDL4245E / BDL4645E
China RoHS
中国电子信息产品污染控制标识要求(中国RoHS法规标示要求)产品中有毒有害物质或元素
的名称及含量
有毒有害物质或元素
部件名称
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr6+)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
外壳
O
O
O
O
O
O
液晶面板
X
X
O
O
O
O
电路板组件
X
O
O
O
O
O
附件
(遥控器,电源线,连接线)
X
O
O
O
O
O
遥控器电池
X
O
O
O
O
O
O: 表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006标准规定的限量要求以下.
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006标准规定的限量要求.
10
環保使用期限
此標識指期限(十年),電子信息產品中含有的有毒有害物質或元素在正常使用的條件下不會發生外泄或突變
,電子信息產品用戶使用該電子信息產品不會對環境造成嚴重污染或對其人身、財產造成嚴重損害的期限。
vi
BDL3245E / BDL4245E / BDL4645E
North Europe (Nordic Countries) Information
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS.
Placering/Ventilation
ADVARSEL:
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
End-of-Life Disposal
Your new TV/Monitor contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of
reusable materials and to minimize the amount to be disposed of.
Please find out about the local regulations on how to dispose of your old monitor from your local Philips dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on recycling
contact www.eia.org (Consumer Education Initiative)
Waste Electrical and Electronie Equipment-WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European Directive 2002/96/EG governing used electrical
and electronic appliances, this product may not be disposed of with normal household waste. You are responsible for disposal of this
equipment through a designated waste electrical and electronic equipment collection. To determine the locations for dropping off such
waste electrical and electronic, contact your local government office, the waste disposal organization that serves your household or the
store at which you purchased the product.
Attention users in United States:
Like all LCD products, this set contains a lamp with Mercury. Please dispose of according to all Local, State and Federal Laws. For the disposal or recycling
information, contact: www.mygreenelectronics.com or www.eiae.org.
End of Life Directives-Recycling
Your new TV/Monitor contains several materials that can be recycled for new users.
Like all LCD produces, this set contains a lamp with Mercury. Please dispose of according to all Local. State and Federal laws.
As an ENERGY STAR Partner, MMD has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
vii
BDL3245E / BDL4245E / BDL4645E
Table Of Contents
1. Unpacking and Installation...................................... 1
1.1. Unpacking......................................................................1
1.2. Package Contents......................................................1
1.3. Installation Notes.......................................................1
1.4. Installing and Removing Table Stands..............2
1.5. Mounting on a Wall..................................................3
1.6. Mounting in Portrait Position..............................4
1.6.1. How to use the logo guider for
portrait position.........................................4
1.6.2. How to remove the logo......................4
4. OSD Menu (Need Check)..................................15
4.1. Navigating the OSD Menu..............................15
4.1.1. Navigating the OSD menu using the
remote control........................................15
4.1.2. Navigating the OSD menu using the
monitor’s control buttons..................15
4.2. OSD Menu Overview.........................................15
4.2.1. Picture menu.............................................15
4.2.2. Screen menu.............................................16
4.2.3. Audio menu...............................................16
4.2.4. PIP menu.....................................................17
4.2.5. Configuration1 menu...........................17
4.2.6. Configuration2 menu...........................18
4.2.7. Advanced option menu......................19
2. Parts and Functions.................................................. 5
2.1. Control Panel...............................................................5
2.2. Input/Output Terminals..........................................6
2.3. Remote Control.........................................................7
2.3.1. General functions......................................7
2.3.2. Inserting the batteries in the remote
control.............................................................8
2.3.3. Handling the remote control..............8
2.3.4. Operating range of the remote
control.............................................................8
5. Input Mode (Need Check)...................................22
6. Pixel Defect Policy..................................................23
6.1. Pixels and Sub-Pixels.............................................23
6.2. Types of Pixel Defects + Dot Definition.. 23
6.3. Bright Dot Defects................................................23
6.4. Dark Dot Defects..................................................24
6.5. Proximity of Pixel Defects.................................24
6.6. Pixel Defect Tolerances.......................................24
3. Connecting External Equipment........................... 9
3.1. Using the Switch Cover.........................................9
3.2. Connecting External Equipment (DVD/
VCR/VCD).................................................................10
3.2.1. Using COMPONENT video
input...............................................................10
3.2.2. Using HDMI video input....................10
3.3. Connecting a PC.....................................................11
3.3.1. Using VGA input......................................11
3.3.2. Using DVI input.......................................11
3.3.3. Using HDMI input..................................12
3.4. External Audio Connection..............................13
3.4.1. Connecting external speakers........13
3.4.2. Connecting external audio
device............................................................13
3.5. Connecting Monitors in a Daisy-chain
Configuration............................................................14
3.5.1. Video connection...................................14
3.5.2. Audio connection...................................14
7. Cleaning and Troubleshooting (Need Check).. 25
7.1. Cleaning.......................................................................25
7.2. Troubleshooting.......................................................26
8. Technical Specifications (Need Check).............27
viii
BDL3245E / BDL4245E / BDL4645E
1.
Unpacking and Installation
1.1.
Unpacking
• This product is packed in a carton, together with the standard accessories.
• Any other optional accessories will be packed separately.
• The weight of the product differs - depending on the type. Due to the size and weight, it is recommended to move it by 2 people.
• After opening the carton, ensure that the content is in good condition and complete.
1.2.
Package Contents
Please verify that you received the following items with your package content:
• LCD monitor
• CD ROM
• Remote control with AAA batteries
• Power cord (1.8 m)
• VGA signal cable (1.8 m)
• Quick Installation Guide
POWER
• Table stand
• Main switch cover
SMART
VIDEO
SOURCE
ON/OFF
INPUT
AUDIO
SOURCE
PIP
CONTRAST
• Screw for main switch cover (M3x8)
CHANGE
BRIGHTNESS
DISPLAY
MENU
SET
AUTO
ADJUST
• BNC-to-RCA adapter (x5)
EXIT
VOL UP
MUTE
VOL DOWN
• Logo guider
Main switch cover
* The supplied power cord varies depending on destination.
For EU
For China
For North America
For UK
User’s Manual
Remote Control
and AAA Batteries
Screw for Main switch cover BNC-RCA adapter x 5
(M3 x 8) x 1
Video Signal Cable
(D-SUB to D-SUB Cable)
Logo guider
NOTES:
• Please make sure that for all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been approved by and
complies with the safety regulations of the particular country.
• You might like to save the package box and packing material for shipping the monitor.
1.3.
Installation Notes
• Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line is required, please consult your
service agent.
• The product should be installed on a flat surface to avoid tipping. The distance between the back of the product and the wall should be maintained
for proper ventilation. Avoid installing the product in the kitchen, bathroom or any other places with high humidity so as not to shorten the service life
of the electronic components.
• The product can normally operate only under 4000m altitude. It might abnormally function in locations over 4000m altitude and do not install and
operate there.
1
BDL3245E / BDL4245E / BDL4645E
1.4.
Installing and Removing Table Stands
To install table stands:
1. Power off the monitor.
2. Spread a protective sheet on a flat surface.
3. Grab the carrying handles and place the monitor face-down on the protective sheet.
4. After inserting the stand in the guide block, tighten the screws on both sides of the monitor.
NOTE: The long-end side of the stand should face to the front while installing.
Carrying handle
Thumbscrews
Longer portions directs to the front
Table stand
To remove table stands:
1. Power off the monitor.
2. Spread a protective sheet on a flat surface.
3. Grab the carrying handles and place the monitor face-down on the protective sheet.
4. Remove screws using a screwdriver and place them in a safe place for reuse.
2
BDL3245E / BDL4245E / BDL4645E
1.5.
Mounting on a Wall
To mount this monitor to a wall, you will have to obtain a standard wall-mounting kit (commercially available). Using mounting interface that complies with
TÜV-GS and/or UL1678 standard in North America is recommended.
100
200
100
Protective Sheet
200
Table
Tabletop stand
1. Lay a protective sheet on a table, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the
screen face.
2. This device cannot be used or installed without the Tabletop Stand or other mounting accessory. Make sure all these stuffs are ready for wall-mount
installation.
3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment
or injury to the user or installer. Product warranty does not cover damage caused by improper installation.
4. For the wall-mounting kit, use M6 mounting screws (having a length 10 mm longer than the thickness of the mounting bracket) and tighten them
securely. (Recommended torque: 470 - 635N•cm).
Caution:
To prevent the monitor from falling:
• Install the monitor with metal brackets for wall or ceiling installation (commercially available) on your own responsibility. For detailed procedures of
installation, refer to the instructions of the metal brackets.
• To lessen the probability of injury and damage resulting from fall of the monitor in case of earthquake or other disaster, be sure to consult the bracket
manufacturer for installation location.
Ventilation Requirements for enclosure locating
To allow heat to disperse, leave space between surrounding objects as shown
in the diagram below.
100 mm
100 mm
100 mm
100 mm
3
BDL3245E / BDL4245E / BDL4645E
1.6.
Mounting in Portrait Position
This monitot can be installed in portrait position.
1. Remove the table stand if they are attached.
2. The “
” logo should be on the LEFT side when facing the monitor.
90
90
1.6.1. How to use the logo guider for portrait position
a. B
efore applying, make sure that the guider is in good condition. Fold the
“
” logo back in at the end of the guider.
b. Peel off the back side of the protective film from the logo.
c. A
djust the logo guider to align it with the long side of the front bezel
and press the guider with your hand.
d. K
eep pressing the guider with your one hand and use the other hand to
fold the logo out. Make sure that the logo is aligned with the front short
bezel. Press firmly and repeatedly on the logo to make the logo stick
tight on the front bezel.
e. Remove the guider.
1.6.2. How to remove the logo
1. Prepare a piece of paper with a cutting area of logo as a protector to
prevent the front bezel from scratching.
1
2
3
2. Using a knife, carefully remove the logo sticker with the paper placing
beneath.
3. Tear off the logo sticker.
NOTE:
When installing the monitor on a wall, please consult a professional technician for proper installing. The manufacturer accepts no liability for
installations not performed by a professional technician.
4
BDL3245E / BDL4245E / BDL4645E
2.
Parts and Functions
2.1.
Control Panel
9
MUTE INPUT
1
1
2
3
MENU
4
5
6
7
8
POWER button
NOTE:“Keyboard Control Lock Mode” This function completely
disables the access to all Keyboard Control functions. To
enable or disable the keyboard control lock, press both [ ]
and [ ] buttons and hold down continuously for more than
3 (three) seconds.
Switch the power on or put the monitor to standby.
2
MUTE button
Switch the audio mute ON/OFF.
3
INPUT button
9
Set the function while OSD menu is on, or to activate input
selection menu while OSD menu is off.
4
• Receives command signals from the remote control.
• Indicates the operating status of the monitor:
[ ] button
-- Lights green when the monitor is turned on
Increase the adjustment while OSD menu is on, or to decrease the
audio output level while OSD menu is off.
5
6
-- Lights red when the monitor is in standby mode
[ ] button
-- Lights amber when the monitor enters DPMS mode
Decrease the adjustment while OSD menu is on, or to decrease the
audio output level while OSD menu is off.
-- When {SCHEDULE} is enabled, it would blink green and red
-- If the indicator blinks red, it tells that a failure is detected
[ ] button
-- Off when the main power of the monitor is turned off
Move the highlight bar up to adjust the selected item while OSD
menu is on.
7
[ ] button
Move the highlight bar down to adjust the selected item while OSD
menu is on.
8
Remote control sensor and power status indicator
MENU button
Return to previous menu while OSD menu is on, or to activate the
OSD menu when OSD menu is off.
5
BDL3245E / BDL4245E / BDL4645E
2.2.
Input/Output Terminals
BDL3245E
BDL4245E/BDL4645E
15
15
BDL3245E
(OUT)
(OUT)
Pr
Pb
Y
1
3
2
(IN)
1
2
(IN)
3
4
5
6
7
8
9
10
11 12 10
13
14
BDL4245E/BDL4645E
(OUT)
(OUT)
Pr
Pb
Y
1
3
2
(IN)
2
1
2
1
3
(IN)
4
5
6
7
MAIN POWER SWITCH
8
10
RS232C (OUT/IN)
11
• VIDEO IN (BNC): Connect the composite video signal input.
RJ-45
• VIDEO OUT (BNC): Connect the composite video signal
output from VIDEO IN (BNC).
12
VGA OUT (D-Sub)
AUDIO OUT R/L (RCA)
Connect the audio signal output from AUDIO IN 1, 2, or 3 jack to
an external AV device.
DVI-D IN
13
SPEAKERS OUT R/L
Connect the audio output to external speakers.
14
HDMI IN
SPEAKER SWITCH
Press to switch the internal speaker on/off.
15
Kensington Lock
For security and theft prevention.
VGA IN (D-Sub)
Connect the computer VGA output.
9
VIDEO IN/OUT
• S-VIDEO IN (Mini DIN 4 pin): Connect the S-VIDEO (Y/C
separate signal) input.
Connect the HDMI output of an AV device, or the DVI-D output of
a PC by using a DVI-HDMI cable.
8
AUDIO IN 1, 2, 3
• AUDIO IN 2, 3: RCA phone jack
Connect the DVI-D output of a PC, or the HDMI output of an AV
device by using a DVI-HDMI cable.
7
14
• AUDIO IN 1: 3.5mm stereo phone jack
Output the VGA signal from the VGA IN (D-Sub).
6
13
AC IN
LAN control function for the use of remote control signal from
control center.
5
11 12 10
Connect audio input from external AV device.
RS232C network input/output connection for the use of loopthrough function.
4
10
Press to switch the main power on/off.
Connect the supplied power cord to the wall outlet.
3
9
COMPONENT IN (BNC)
Connect the component YPbPr output from external AV device.
6
BDL3245E / BDL4245E / BDL4645E
2.3.
Remote Control
5
Press to turn on/off the information OSD displayed on the upper
right corner of the screen.
2.3.1. General functions
6
1
• Press to decrease the value in OSD menu.
10
VIDEO
SOURCE
• Press to move the sub-picture left in PIP mode.
AUDIO
SOURCE
2
7
11
12
8
INPUT
NOTE: This button is functional for VGA input only.
CHANGE
4
13
CONTRAST
BRIGHTNESS
5
DISPLAY
6
9
14
15
10
7
8
17
EXIT
VOL UP
MUTE
[VIDEO SOURCE] button
Press to toggle Video Source Menu. Press [ ] or [ ] button
to select one of the video sources among HDMI, DVI-D, VGA,
Component, S-Video, or Video . Press [SET] button to confirm and
exit.
16
SET
[MUTE] button
Press to turn the mute function on/off.
MENU
AUTO
ADJUST
[AUTO ADJUST] button
Press to run the Auto Adjust function.
3
ON/OFF
[SET] button
Press to activate the setting with OSD menu.
PIP
9
[ ] button
• Press to move the selection left in OSD menu.
POWER
SMART
[DISPLAY] button
11
18
[AUDIO SOURCE] button
Press to toggle Audio Source Menu. Press [ ] or [ ] button to
select one of the audio sources among HDMI, AUDIO1, AUDIO2,
or AUDIO3. Press [SET] button to confirm and exit.
19
20
VOL DOWN
12
Picture Format button
Press to switch screen aspect ratio among FULL, NORMAL,
DYNAMIC, CUSTOM, REAL, or 21:9.
DYNAMIC and 21:9 mode are used for Video input source only.
PC signal: FULL, NORMAL, CUSTOM and REAL.
Video signal: FULL, NORMAL, DYNAMIC, CUSTOM and REAL.
13
[BRIGHTNESS] button
Press to toggle Brightness Menu. Press [ ] or [ ] button to adjust
the value. Press [MENU] button to confirm and exit.
14
[ ] button
• Press to move the selection up in OSD menu.
• Press to move the sub-picture up in PIP mode.
1
[POWER] button
15
Press to turn the OSD menu on/off.
Press to switch on the monitor from standby mode. Press again to
turn it off and back into standby mode.
2
16
[SMART] button
• Press to increase the value in OSD menu.
• Press to move the sub-picture right in PIP mode.
• Standard: Used for normal images (factory setting)
17
• Highbright: Used for moving image such as Video
18
[PIP] (Picture In Picture) button
[ ] button
• Press to move the selection down in OSD menu.
[ON/OFF]: Turn PIP mode ON/OFF.
• Press to move the sub-picture down in PIP mode.
Select the input signal for the sub-picture.
19
[CHANGE]:Toggle between the main picture and sub picture.
4
[EXIT] button
Press to turn back to the previous OSD menu.
• sRGB: Used for text based images
[INPUT]:
[ ] button
• Press to move the selection right in OSD menu.
Press to toggle Smart Menu. Press [ ] or [ ] button to select
menu options. Press [SET] button to confirm and exit the selection.
3
[MENU] button
[VOL UP] button
Press to increase the audio output level.
[CONTRAST] button
20
Press to toggle Contrast Menu. Press [ ] or [ ] button to adjust
the value. Press [MENU] button to confirm and exit.
[VOL DOWN] button
Press to decrease the audio output level.
7
BDL3245E / BDL4245E / BDL4645E
2.3.2. Inserting the batteries in the remote control
The remote control is powered by two 1.5V AAA batteries.
To install or replace batteries:
1. Press and then slide the cover to open it.
2. Align the batteries according to the (+) and (–) indications inside the
battery compartment.
3. Replace the cover.
Caution:
An incorrect use of batteries can result in leaks or bursting. Be careful especially about the following points.
• Place “AAA” batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of the battery compartment.
• Do not mix battery types.
• Do not combine new batteries with used ones. It causes shorter life or leakage of batteries.
• Remove the dead batteries immediately to prevent it from liquid leaking in the battery compartment. Don’t touch exposed battery acid, it cause
damage to your skin.
NOTE:
If you do not intend to use the remote control for a long period, remove the batteries.
2.3.3. Handling the remote control
• Do not subject to strong shock.
• Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immediately.
• Avoid exposure to heat and steam.
• Other than to install the batteries, do not open the remote control.
2.3.4. Operating range of the remote control
Point the top of the remote control toward the monitor’s remote control
sensor when pressing a button.
Use the remote control within a distance of less than 10m/33ft away from
the monitor’s sensor, and a horizontal and vertical angle of less than 30
degrees.
NOTE:
he remote control may not function properly when the remote
T
control sensor on the monitor is under direct sunlight or strong
illumination, or when there is an obstacle in the path of signal
transmission.
30
30
POWER
SMART
VIDEO
SOURCE
AUDIO
SOURCE
PIP
ON/OFF
INPUT
CONTRAST
CHANGE
BRIGHTNESS
DISPLAY
MENU
SET
AUTO
ADJUST
EXIT
VOL UP
MUTE
VOL DOWN
8
BDL3245E / BDL4245E / BDL4645E
3.
Connecting External Equipment
3.1.
Using the Switch Cover
A cover for the main switch is provided to prevent the monitor from being turned on or off accidentally.
To lock the cover into position:
1. Align and insert the cover to the ditch located beside the main switch.
2. Use the screw to lock the cover.
BDL3245E:
1
Screw
2
Main switch cover
BDL4245E / BDL4645E:
1
Screw
2
Main switch cover
9
BDL3245E / BDL4245E / BDL4645E
3.2.
Connecting External Equipment (DVD/VCR/VCD)
3.2.1. Using COMPONENT video input
COMPONENT
(YPbPr)
Audio Output
DVD / VCR / VCD
To [AUDIO IN 2, 3]
COMPONENT
(YPbPr)
3.2.2. Using HDMI video input
DVD / VCR / VCD
HDMI connector
HDMI connector
10
BDL3245E / BDL4245E / BDL4645E
3.3.
Connecting a PC
3.3.1. Using VGA input
From analog VGA output
Mini D-Sub 15 pin
From audio output
PC or IBM compatible
To [AUDIO IN 1, 2, 3]
To [VGA IN]
3.3.2. Using DVI input
From DVI output
From audio output
PC or IBM compatible
To [AUDIO IN 1, 2, 3]
To [DVI IN]
11
BDL3245E / BDL4245E / BDL4645E
3.3.3. Using HDMI input
From HDMI output
PC or IBM compatible
To [HDMI IN]
12
BDL3245E / BDL4245E / BDL4645E
3.4.
External Audio Connection
3.4.1. Connecting external speakers
External speaker
3.4.2. Connecting external audio device
To [AUDIO OUT]
RCA
Audio In
Stereo Amplifier
13
BDL3245E / BDL4245E / BDL4645E
3.5.
Connecting Monitors in a Daisy-chain Configuration
You can interconnect multiple sets of this monitor to create a daisy-chain configuration for applications like a TV wall.
NOTE:
Maximum 25 displays (5x5) can be used in a daisy-chain configuration.
3.5.1. Video connection
Do one the following connections:
• Connect the [RS232C OUT] connector of monitor 1 to the [RS232C IN] connector of monitor 2.
• Connect the [VGA OUT] connector of monitor 1 to the [VGA IN] connector of monitor 2.
• Connect the [VIDEO OUT] connector of monitor 1 to the [VIDEO IN] connector of monitor 2.
To RS-232C IN
PC
To RS-232C OUT
To RS-232C IN
RS-232C Cable
RS-232C Cable
3.5.2. Audio connection
Do one the following connections:
• Connect the [AUDIO OUT] connector of monitor 1 to the [AUDIO IN 2] OR [AUDIO IN 3] connector of monitor 2.
• Connect the [VGA OUT] connector of monitor 1 to the [VGA IN] connector of monitor 2.
• Connect the [VIDEO OUT] connector of monitor 1 to the [VIDEO IN] connector of monitor 2.
PC
To [AUDIO IN 1, 2, 3]
To [AUDIO OUT]
14
To [AUDIO IN 2, 3]
BDL3245E / BDL4245E / BDL4645E
4.
OSD Menu (Need Check)
Brightness
Adjust the overall image brightness by changing the intensity of the LCD
panel’s backlight.
An overall view of the On-Screen Display (OSD) structure is shown
below. You can use it as a reference for further adjusting your monitor.
4.1.
Contrast
Navigating the OSD Menu
Adjust to sharpen the picture quality. The black portions of the picture
become richer in darkness and the white become brighter.
4.1.1. Navigating the OSD menu using the
remote control
Sharpness
Adjust to improve detail.
Black level
Adjust to change the image brightness.
MENU
Noise reduction
Adjust to remove the noise in the image. You can select a suitable noise
reduction level.
SET
The options are: {Off} / {Low} / {Medium} / {High}.
NOTE:
EXIT
Tint
1. Press [MENU] button on the remote control to display the OSD
menu.
2. Press [
] or [
Adjust to change the color tint of the image.
The tone color becomes greenish by increasing the value, and becomes
purplish by decreasing the value.
] button to choose the item you want to adjust.
NOTE:
3. Press [SET] or [ ] or button to enter the submenu.
4. In the submenu, press [ ] or [ ] button to toggle among items,
press [ ] or [ ] button to adjust settings. If there is a submenu,
press [SET] or [ ] button to enter the submenu.
his item is functional for HDMI(Video mode), S-Video, Video,
T
and YPbPr inputs only.
Color
Adjust to increase or decrease the intensity of colors in the image.
NOTE:
5. Press [EXIT] button to return to the previous menu, or press
[MENU] button to exit the OSD menu.
his item is functional for S-Video, Video, and YPbPr inputs
T
only.
Color temperature
4.1.2. Navigating the OSD menu using the
monitor’s control buttons
Select a color temperature for the image. The image looks reddish
with a lower color temperature, and looks bluish with a higher color
temperature.
1. Press [MENU] button to display the OSD menu.
The options are: {3000K} / {4000K} / {5000K} / {6500K} / {7500K} /
{9300K} / {10000K} / {Native} / {User}.
2. Press [ ] or [ ] button to choose the item you want to adjust.
3. Press [SOURCE] or [ ] button to enter the submenu.
Color control
4. In the submenu, press [ ] or [ ] button to toggle among items,
press [ ] or [ ] button to adjust settings. If there is a submenu,
press [SOURCE] or [ ] button to enter the submenu.
With this function you can adjust the color tones of the image precisely
by changing the R (Red), G (Green) and B (Blue) settings independently.
NOTE:
5. Press [MENU] button to return to the previous menu, or press
[MENU] button several times to exit the OSD menu.
4.2.
his item is functional for HDMI(Video mode), S-Video, Video,
T
and YPbPr inputs only.
his item is functional only when {Color temperature} is set
T
to {User}.
Smart contrast
OSD Menu Overview
When turned on, this function helps enhance image contrast when
displaying dark scenes.
4.2.1. Picture menu
Smart picture
Brightness
The following smart picture modes are available for:
Contrast
Screen
• PC mode: {Standard} / {Highbright} / {sRGB}.
Sharpness
Black level
• Video mode: {Standard} / {Highbright} / {Cinema}.
Audio
Picture
PIP
Configuration1
Configuration2
Advanced option
Noise reduction
Video source
Tint
Select a video input source.
Color
Picture reset
Color temperature
Reset all settings in the Picture menu.
Color control
Smart contrast
Smart picture
15
BDL3245E / BDL4245E / BDL4645E
4.2.2. Screen menu
Picture
21:9
The picture is enlarged to 16:9 format. This
mode is recommended when displaying
pictures that have black bands at the top and
bottom (letterbox format).
H position
V position
Screen
Audio
PIP
Configuration1
Clock
Clock phase
Zoom mode
Custom zoom
Custom zoom
You can use this function to further customize the zoom settings to suit
the image you want to display.
Screen reset
NOTE:
Configuration2
his item is functional only when the Zoom mode setting is
T
set to Custom.
Zoom
Advanced option
Expands the horizontal and vertical sizes of the
image simultaneously.
H position
H zoom
Adjust the horizontal placement of the picture.
Expands the horizontal size of the image only.
V position
Adjust the vertical placement of the picture.
V zoom
Clock
Expands the vertical size of the image only.
Adjust the width of the image.
NOTE:
This item is functional for VGA input only.
H position
Clock phase
Moves the horizontal position of the image left
or right.
Adjust to improve the focus, clarity and stability of the image.
NOTE:
This item is functional for VGA input only.
Zoom mode
V position
The pictures you receive may be transmitted in 16:9 format (wide
screen) or 4:3 format (conventional screen). The 16:9 pictures
sometimes have a black band at the top and bottom of the screen
(letterbox format).
Moves the vertical position of the image up or
down.
This function allows you to optimize the picture display on screen. The
following zoom modes are available for:
Screen reset
Reset all settings in the Screen menu.
• PC mode: {Full} / {Normal} / {Custom} / {Real}.
4.2.3. Audio menu
• Video mode: {Full} / {Normal} / {Dynamic} / {Custom} / {Real} /
{21:9}.
Picture
Full
Balance
Treble
This mode restores the correct proportions
of pictures transmitted in 16:9 using the full
screen display.
Screen
Bass
Audio
Volume
Mute
Normal
PIP
The picture is reproduced in 4:3 format and
a black band is displayed on either side of the
picture.
Configuration1
Audio source
Audio reset
Configuration2
Dynamic
Advanced option
Fill the entire screen by stretching 4:3 pictures
non-proportionally.
Balance
Custom
Choose to apply the custom zoom settings in
the Custom Zoom submenu.
Adjust to emphasize left or right audio output balance.
Real
Adjust to increase or decrease higher-pitched sounds.
Treble
This mode displays the image pixel-by-pixel
on screen without scaling the original image
size.
Bass
Adjust to increase or decrease lower-pitched sounds.
16
BDL3245E / BDL4245E / BDL4645E
Volume
Main Picture
Adjust to increase or decrease the audio output level.
DVI
VGA
HDMI
X
X
X
X
O
O
X
X
X
X
O
O
X
X
X
X
O
O
YPbPr S-Video Video
Select the audio input source according to the audio signal source
connected to the audio input and HDMI sockets on the monitor.
Sub Picture
DVI
VGA
HDMI
YPbPr
S-Video
Video
The options are: {HDMI} / {Audio1} / {Audio2} / {Audio3}.
(O: PIP function available, X: PIP function unavailable)
Audio reset
By pressing the [PIP ON/OFF] button on the remote control, you can
change the mode in the order shown below:
Mute
Turn the mute function on/off.
Audio source
Reset all settings in the AUDIO menu.
PIP
PBP aspect
POP
X
X
X
X
O
O
PBP full
O
O
O
O
X
X
O
O
O
O
X
X
Off
4.2.4. PIP menu
Picture
PIP
PIP input
Screen
PIP change
Audio
PIP size
PIP
The resolutions in the PIP and POP modes are configured as follows:
PIP SIZE {SMALL} : 320 x 240 pixels
PIP audio
{Medium} : 480 x 320 pixels
PIP reset
{LARGE} : 640 x 480 pixels
POP SIZE: 450 x 338 pixels
Configuration1
NOTE:
Configuration2
Advanced option
Images displayed in the sub picture always fit the PIP sizes
shown above irrespective of the aspect ratio of the input
image.
4.2.5. Configuration1 menu
Picture
PIP
Switch on state
Auto adjust
Select the PIP (Picture-in-Picture) mode.
Screen
The options are: {Off} / {PIP} / {POP} / {PBP aspect} / {PBP full}.
Audio
Power save
Language
Panel saving
PIP input
PIP
Select the input signal for the sub-picture.
Configuration1
PIP change
Color system
Network control port
Network settings
Exchange between the main picture and sub picture.
Configuration2
PIP size
Advanced option
Configuration reset
Factory reset
Select the size of the sub picture in the PIP (Picture-in-Picture) mode.
The options are: {Small} / {Medium} / {Large}.
PIP audio
Switch on state
Select the audio source in the PIP (Picture-in-Picture) mode.
Select the monitor status used for the next powering on.
• {Main} - Select audio from the main picture
The options are: {Power off} / {Forced on} / {Last status}.
• {Sub} - Select audio from the sub picture.
Auto adjust
PIP reset
Use this function to let the monitor automatically optimize the display
of VGA input image.
Reset all settings in the PIP menu.
NOTE:
NOTES:
This item is functional for VGA input only.
Power save
• The PIP function is available only for certain signal source
combinations as shown in the table below.
Set the monitor to reduce the power automatically.
• {RGB} - Select {On} to let the monitor enter DPMS mode with no
signal detected from the HDMI Graphic mode, HDMI, DVI-D, or
VGA inputs after three successive cycles.
• The availability of the PIP function will also depend on the resolution
of the input signal being used.
• {VIDEO} - Select {On} to let the monitor enter power saving mode
with no signal detected from the HDMI Video mode or YPbPr
inputs after three successive cycles.
17
BDL3245E / BDL4245E / BDL4645E
Language
Factory reset
Select the language used in the OSD menu.
The options are: {
{
}/{
} /{
}/{
}/{
}/{
}/ {
}.
}/{
}/
Panel saving
4.2.6. Configuration2 menu
• {Cooling Fan} - Select {On} to turn on the cooling fan all the
time. Select {Auto} to turn on/off the cooling fan according to the
monitor temperature.
NOTE:
Reset
Cancel
Choose to enable the panel saving functions to reduce the risk of the
“image persistence”.
Picture
OSD turn off
Information OSD
he speed of the cooling fan is pre-set to {low}, {mid}, or
T
{high} speed each at 50°C, 58°C, or 63°C respectively. The
monitor will automatically shut down by reaching a preset
critical temperature of 82°C.
Screen
Audio
Off timer
OSD H-position
OSD V-position
• {Brightness} - Select {On} and the brightness of the image will be
reduced to an appropriate level, and the Brightness setting in the
Picture menu will become unavailable.
PIP
Monitor information
Configuration1
• {Pixel shift} - Select the time interval ({Auto} / {10 ~ 900} Seconds
/ {Off}) for the monitor to slightly expand the image size and shift
the position of pixels in four directions (up, down, left, or right).
Configuration2
Advanced option
Network control port
Select the nectwork control port.
The options are: {RJ-45} / {RS-232}.
OSD turn off
Network settings
Set the period of time the OSD menu stays on the screen.
The options are: {5 ~ 120} seconds.
Assign {IP}, {Subnet Mask}, and {Default gateway} for the display.
Information OSD
Network settings
Network host name
Set the period of time the information OSD displayed on the upper
right corner of the screen. The information OSD will display when input
signal is changed.
0
0
0
0
0
0
The information OSD will remain on the screen with {Off} selection.
The options are: {1 ~ 60} seconds.
Disable
DHCP
IP address
0
-
0
-
0
-
0
Off Timer
Subnet mask
0
-
0
-
0
-
0
Default gateway
0
-
0
-
0
-
0
Set the monitor to turn itself off to standby mode within an amount of
time specified.
a d m i n
Login user name
Login password
0
0
0
The options are: {Off, 1 ~ 24} hours.
0
NOTE:
[ SET ]
change [SET] in STORE
hen the “Off timer” is activated, the “Schedule” settings will
W
be disabled.
OSD H-position
• DHCP - Choose to enable or disable the DHCP function. If enabled,
the display will be assigned IP address, Subnet mask and Default
gateway automatically. If disabled, you will be prompted to enter the
following value manually. Finally, press [SET] button to store and save
the chosen values.
Adjust the horizontal position of the OSD menu.
OSD V-position
Adjust the vertical position of the OSD menu.
Monitor Information
• IP address
Displays the information about your monitor, including model number,
serial number, operating hours and software version.
• Subnet mask
• Default gateway
Monitor information
• Login user name
• Login password
Configuration reset
Model name:
Serial:
Operation Hours:
Sw Version:
Reset all settings in the Configuration1 menu.
Factory reset
Reset all the settings in the OSD menus of {Picture}, {Screen}, {Audio},
{PIP}, {Configuration1}, {Configuration2}, and {Advanced option}.
Press [ ] or [ ] button to select [Reset], and then press [SET] button
to do the reset.
18
BDL3245E
0H
VER 0.203
3M
BDL3245E / BDL4245E / BDL4645E
4.2.7. Advanced option menu
Picture
per-second (24 fps) input signal format to DVD video signal format.
Once this function is enabled, it is recommended that you set the
{Scan conversion} function to {Progressive}.
Input resolution
• {Off} - Disable the film mode frame conversion function. This mode
is suitable for TV broadcasting and VCR signals.
Black level expansion
Screen
Audio
PIP
Configuration1
Gamma selection
Scan mode
IR control
Scan conversion
Select the operation mode of the remote control when multiple
monitors are connected via the RS232C connection.
Film mode
IR control
• {Normal} - All monitors can be operated normally by the remote
control.
Keyboard control
Configuration2
Advanced option
Tiling
• {Primary} - Designate this monitor as the primary monitor for
remote control operation. Only this monitor can be operated by
the remote control.
Heat status
Date and time
• {Secondary} - Designate this monitor as the secondary monitor. This
monitor can not be operated by the remote control, and will only
receive the control signal from the primary monitor via the RS232C
connection.
Input resolution
Set the resolution of the VGA input. This is only required when the
monitor is unable to detect the VGA input resolution correctly.
NOTE:
• {Lock} - Lock the remote control function of this monitor. To unlock,
press and hold the [DISPLAY] button on the remote control for 5
(five) seconds.
This item is functional for VGA input only.
The options are:
Keyboard control
• {1024x768 / 1280x768 / 1360x768}
Choose to enable or disable the monitor keyboard (control buttons)
function.
• {1400x1050 / 1680x1050}
• {1600x1200 / 1920x1200}
• {Lock} - Disable the keyboard function.
• {Auto}: Determines the resolution automatically.
• {Unlock} - Enable the keyboard function.
The selected settings will become effective after turning off the power
and turn it on again.
Tiling
With this function you can create a single large-screen matrix (display
wall) that consists of up to 25 sets of this monitor (up to 5-set each at
the vertical and horizontal side). This function requires a daisy-chain
connection.
Black level expansion
Select a suitable black level expansion setting to reveal more details in
the dark parts of an image.
The options are: {Off} / {Low} / {Medium} / {High}.
NOTE:
Tiling
This item is functional for Video mode inputs only.
Gamma selection
Select a display gamma value to best suit the image and optimize image
brightness and contrast.
H monitors
1
V monitors
1
Position
The options are: {Native} / {2.2} / {2.4} / {S gamma}.
Scan mode
Change the display area of the image.
No
Enable
No
Switch On Delay
Off
Example: 2 x 2 screen matrix (4 monitors)
H monitors = 2 monitors
V monitors = 2 monitors
• {Overscan} - Display about 95% of the original size of the image.
The rest of the areas surrounding the image will be cut off.
• {Underscan} - Display the image in its original size.
NOTE:
1
Frame comp.
H monitors
his item is functional for HDMI-Video timing, DVI-D(HD
T
timing), DP(HD timing), and YPbPr inputs only.
Scan conversion
V monitors
Choose to enable or disable the IP (Interlace to Progressive) conversion
function.
• {Progressive} - Enable the IP conversion function (recommended).
Once enabled, the interlace input signal will be converted to
progressive format for better display quality.
• {Interlace} - Disable the IP function. This mode is suitable for
displaying motion pictures, but it increases the chance of image
retention.
Film mode
Choose to turn on or off the film mode frame conversion function.
• {Auto} - Enable the film mode frame conversion function for
movies and motion pictures. The monitor converts a 24 frames-
19
1
2
3
4
Position
BDL3245E / BDL4245E / BDL4645E
Example: 5 x 5 screen matrix (25 monitors)
H monitors = 5 monitors
V monitors = 5 monitors
Heat status
This function allows you to check the thermal status of the monitor at
any time. The accuracy of the temperature indicated is +/- 5 degrees (C
or F).
V monitors
H monitors
Date and time
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Year
16
17
18
19
20
Month
08
Day
04
21
22
23
24
25
Hour
20
Minute
20
Adjust the current date and time for the monitor’s internal clock.
Position
Date and time
2011
Daylight saving time
• H monitors - Select the number of monitors on the horizontal side.
Current date time
• V monitors - Select the number of monitors on the vertical side.
2011 . 08 . 04
• Position - Select the position of this monitor in the screen matrix.
20 : 20 : 17
Press [SET] to set clock
• Frame comp. - Choose to turn the frame compensation function on
or off. If turned on, the monitor will adjust the image to compensate
for the width of the monitor bezels in order to accurately display
the image.
1. Press [ ] button to enter the submenu.
2. Press [ ] or [ ] button to toggle among the {Year}, {Month},
{Day}, {Hour}, {Minute}, and {Daylight saving time} settings.
Frame comp. - Off
3. Press [ ] or [ ] button to adjust all settings except {Daylight
saving time}.
4. Press [SET] button to enter the {Daylight saving} submenu.
5. Press [ ] or [ ] button to select item, press [
to adjust.
] or [
] button
Schedule
This function allows you to program up to 7 (seven) different scheduled
time intervals for the monitor to activate.
You can select:
• The time for the monitor to turn on and turn off.
• The days in a week for the monitor to activate.
• Which input source the monitor will use for each scheduled
activation period.
Frame comp. - On
NOTE:
ou should set up current date and time in {Date and time}
Y
menu before using this function.
1. Press [SET] or [ ] button to enter the submenu.
Schedule
Today
1
2
3
4
5
6
7
• Enable: Choose to enable or disable the Tiling function. If enabled,
the monitor will apply the settings in H monitors, V monitors,
Position, and Frame comp.
On
_:_
Every day
Wed
SAT
THU
Off
_:_
MON
THU
SUN
20 : 19 : 55
Input
_
TUE
FRI
Every week
2. Press [ ] or [ ] button to select a schedule item (item number 1
~ 7), and then press [ ] button to mark it the item number.
• Switch On Delay: {Off / Auto / 2, 4, 6, 8, 10, 20, 30, 40, 50}
NOTE:
2011 . 08 . 04
The Tiling function will be disabled when the [ON/OFF]
button for PIP is pressed.
20
BDL3245E / BDL4245E / BDL4645E
Advanced option reset
Schedule
Reset all settings in the Advanced option menu.
1. Press [SET] or [ ] button to enter the submenu.
Today
1
2
3
4
5
6
7
2011 . 08 . 04
On
_:_
1
Every day
Wed
SAT
Off
_:_
THU
2. Press [ ] or [ ] button to select {Reset} and press the [SET]
button to restore settings to factory preset values.
20 : 19 : 55
2
MON
THU
SUN
Input
_
3
TUE
FRI
Every week
3. Press the [EXIT] button or select {Cancel} and press the [SET]
button to cancel and then return to the previous menu.
4
Picture
Schecule
Action
Screen
Monitor ID
Action
Audio
DDC/CI
On
Smart power
Off
Auto signal detection
Off
Advanced option reset
Action
PIP
3. Press [ ] or [ ] button to select the schedule:
1 P
ower-on schedule: Press [ ] or [ ] button to set the hour
and minute for the monitor to turn on.
2
Configuration1
Configuration2
Power-off
schedule: Press [ ] or [ ] button to set the hour
and minute for the monitor to turn off.
Advanced option
Select or leave an empty “__” for both the hour and minute slot if
you do not want to use this power-on or power-off schedule.
3
Input-source selection: Press [ ] or [ ] button to select an
input source. If no input source is selected, the input source
will remain the same as last selected.
4
D
ate schedule: Press [ ] button to select which day in a
week this schedule item will be take effect, and then press the
[SET] button.
4. For more schedule settings, press [EXIT] button and then repeat
the steps above. A check mark in the box next to the number of
the schedule item indicates that the selected schedule is in effect.
NOTES:
• The {Every day} selection in a schedule item takes priority over
other weekly schedules.
• If the schedule overlap, the scheduled power-on time takes priority
over scheduled power-off time.
• If there are two schedule items programmed for the same time, the
highest numbered schedule takes priority.
Monitor ID
Set the ID number for controlling the monitor via the RS232C
connection. Each monitor must have an unique ID number when
multiple sets of this monitor are connected.
DDC/CI
Choose to turn on or off the DDC/CI communication function. Select
{On} for normal use.
Smart power
Set the monitor to reduce the power consumption automatically.
The options are: {Off} / {Medium} / {High}.
Auto signal detection
Choose to let the monitor detect and display available signal sources
automatically.
• {ON} - Set the monitor to display the image automatically once a
signal is connected.
• {OFF} - Once a signal is connected, it can only be selected manually.
21
BDL3245E / BDL4245E / BDL4645E
5.
Input Mode (Need Check)
VGA Resolution
Standard
Resolution
VGA
WVGA
SVGA
XGA
WXGA
WXGA
SXGA
SXGA
WXGA
WXGA
UXGA
HD1080
Active Resolution
H Pixels
V Lines
480
640
72 Hz
75 Hz
720
400
600
800
75 Hz
768
1024
75 Hz
1280
768
1280
800
1280
960
1280
1024
1360
768
1366
768
1600
1200
1920
1080
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
60 Hz
72 Hz
75 Hz
70 Hz
60 Hz
75 Hz
60 Hz
75 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
25.175 MHz
31.5 MHz
31.5 MHz
33.75 MHz
40 MHz
49.5 MHz
65 MHz
78.75 MHz
79.5 MHz
79.5 MHz
108 MHz
108 MHz
85.5 MHz
85.5 MHz
162 MHz
148.5 MHz
4:3
Video Graphic Array
16:9
Wide Video Graphic Array
4:3
Super VGA
4:3
Extended Graphic Array
5:3
16:10
4:3
5:4
16:9
16:9
4:3
16:9
Wide XGA
Wide XGA
Super XGA
Super XGA
Wide XGA
Wide XGA
Ultra XGA
HD1080
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
29.97 Hz
59.94 Hz
25 Hz
50 Hz
13.5 MHz
27 MHz
13.5 MHz
27 MHz
4:3
Modified NTSC Standard
4:3
Modified PAL Standard
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
74.25 MHz
16:9
Normally DVB Mode
74.25 MHz
16:9
Normally ATSC Mode
148.5 MHz
16:9
Normally ATSC Mode
SDTV Resolution
Standard
Resolution
480i
480p
576i
576p
Active Resolution
H Pixels
V Lines
720
480
720
480
HDTV Resolution
Standard
Resolution
Active Resolution
H Pixels
V Lines
720p
1280
720
1080i
1920
1080
1080p
1920
1080
50 Hz
60 Hz
25 Hz
30 Hz
50 Hz
60 Hz
• The PC text quality is optimum in HD 1080 mode (1920 x 1080, 60Hz).
• Your PC display screen might appear different depending on the manufacture (and your particular version of Windows).
• Check your PC instruction book for information about connecting your PC to a display.
• If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5KHz (horizontal). In some cases, abnormal signals (such as
stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the [INPUT] button to enter the
video mode. Also, make sure that the PC is connected.
• When horizontal synchronous signals seem irregular in RGB mode, check PC power saving mode or cable connections.
• The display settings table complies to the IBM/VESA standards, and based on the analog input.
• The DVI support mode is regarded as same to the PC support mode.
• The best timing for the vertical frequency to each mode is 60Hz.
22
BDL3245E / BDL4245E / BDL4645E
6.
Pixel Defect Policy
Philips strives to deliver the highest quality products. We use some of the industry’s most advanced manufacturing processes and practice stringent quality
control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays are sometimes unavoidable. No manufacturer can
guarantee that all panels will be free from pixel defects, but Philips guarantees that any Plasma- & LCD- displays with an unacceptable number of defects
will be repaired during the warranty period in line with your local guarantee conditions.
This notice explains the different types of pixel defects and defines the acceptable defect level for this LCD screen. In order to qualify for repair under
warranty, the number of pixel defects must exceed a certain level which is given in the reference table. If the LCD screen is within specification a warranty
exchange / claim back will be refused. Additionally, because some types or combinations of pixel defects are more noticeable than others, Philips sets even
higher quality standards for those.
6.1.
Pixels and Sub-Pixels
A pixel, or picture element, is composed of three sub-pixels in the primary colors of red, green and
blue. Many pixels together form an image. When all sub-pixels of a pixel are lit, the three colored
sub-pixels together appear as a single white pixel. When all are dark, the three colored sub-pixels
together appear as a single black pixel. Other combinations of lit and dark sub-pixels appear as
single pixels of other colors.
subpixel
pixel
6.2.
Types of Pixel Defects + Dot Definition
Pixel and sub-pixel defects appear on the screen in different ways. There are three categories of pixel defects and several types of sub-pixel defects within
each category.
Dot definition = What is a defective “Dot”? :
One or more defective, adjacent sub-pixel are defined as one “dot”. The no. of defective sub-pixels are not relevant to define a defective dot. This means
that a defective dot can consist of one, two or three defective sub-pixels which can be dark or lit.
R G B
One dot = One Pixel; consists of three sub-pixels of Red, Green, and Blue.
6.3.
Bright Dot Defects
Bright dot defects appear as pixels or sub-pixels that are always lit or “on”. These are the examples of bright dot defects:
One lit red, green or blue sub pixel
Two adjacent lit sub pixels:
Red + Blue = Purple
Red + Green = Yellow
Green + Blue = Cyan (Light Blue)
23
Three adjacent lit sub pixels (one white pixel)
BDL3245E / BDL4245E / BDL4645E
6.4.
Dark Dot Defects
Black dot defects appear as pixels or sub-pixels that are always dark or “off ”. These are the examples of black dot defects:
One dark dot
6.5.
Two adjacent dark dots = 1 pair of dark dots
Two dark dots, specifications defines the
minimum distance between dark dots
Proximity of Pixel Defects
Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also specifies tolerances for the
proximity of pixel defects. In the table below you can find specifications about:
• Allowed amount of adjacent dark dots = (adjacent dark dots =1 pair of dark dots)
• Minimum distance between dark dots
• Total no. of all defective dots
6.6.
Pixel Defect Tolerances
In order to qualify for repair due to pixel defects during the warranty period, a PDP / TFT panel in a Philips Plasma / LCD- display must have pixel or subpixel defects exceeding the tolerances listed in the following table.
BRIGHT DOT EFFECT
ACCEPTABLE LEVEL
1 lit sub pixel
2
BLACK DOT EFFECT
ACCEPTABLE LEVEL
1 dark sub pixel
10
TOTAL DOT DEFECTS OF ALL TYPES
12
NOTE: * 1 or 2 adjacent sub pixel defects = 1 dot defect
24
BDL3245E / BDL4245E / BDL4645E
7.
Cleaning and Troubleshooting (Need Check)
7.1.
Cleaning
Cautions When Using the Display
• Do not bring your hands, face or objects close to the ventilation holes of the display. Top of display is usually very hot due to the high temperature
of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too close. Placing
any object near the top of the display could also result in heat related damages to the object as well as the display itself.
• Be sure to disconnect all cables before moving the display. Moving the display with its cables attached may damage the cables and thus case fire or
electric shock danger.
• Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of cleaning or maintenance procedure.
Front Panel Cleaning Instructions
• The front of the display has been specially treated. Wipe the surface gently using only a cleaning cloth or a soft, lint-free cloth.
• If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent solution. Wring the cloth to remove excess liquid. Wipe the surface of
the display to remove dirt. Then use a dry cloth of the same type to dry.
• Do not scratch or hit the surface of the panel with fingers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners.
Cabinet Cleaning Instructions
• If the cabinet becomes dirty, wipe the cabinet with a soft, dry cloth.
• If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent solution. Wring the cloth to remove as much moisture as possible. Wipe
the cabinet. Use another dry cloth to wipe over until the surface is dry.
• Do not allow any water or detergent to come into contact with the surface of the display. If water or moisture gets inside the unit, operating
problems, electrical and shock hazards may result.
• Do not scratch or hit the cabinet with fingers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners on the cabinet.
• Do not place anything made from rubber or PVC near the cabinet for any extended periods of time.
25
BDL3245E / BDL4245E / BDL4645E
7.2.
Troubleshooting
Symptom
Possible Cause
Remedy
No picture is displayed
1. The power cord is disconnected.
1. Plug in the power cord.
2. The main power switch on the back of the
monitor is not switched on.
2. Make sure the power switch is switched on.
3. The selected input has no connection.
3. Connect a signal connection to the monitor.
4. The monitor is in standby mode.
Interference displayed on the monitor or
audible noise is heard
Caused by surrounding electrical appliances or
fluorescent lights.
Move the monitor to another location to see is
the interference is reduced.
Color is abnormal
The signal cable is not connected properly.
Make sure that the signal cable is attached firmly
to the back of the monitor.
Picture is distorted with abnormal patterns
1. The signal cable is not connected properly.
1. Make sure that the signal cable is attached
firmly.
2. The input signal is beyond the capabilities of
the monitor.
2. Check the video signal source to see if it
is beyond the range of the monitor. Please
verify its specifications with this monitor’s
specification section.
Display image doesn’t fill up the full size of the
screen
The zoom mode is not correctly set.
Use the Zoom mode or Custom zoom function
in the Screen menu to fine tune display geometry
and time frequency parameter.
Can hear sound, but no picture
Improperly connected source signal cable.
Make sure that both video inputs and sound
inputs are correctly connected.
Can see picture but no sound is heard
1. Improperly connected source signal cable.
1. Make sure that both video inputs and sound
inputs are correctly connected.
2. Volume is turned all the way down.
3. [MUTE] is turned on.
4. No external speaker connected.
2. Press [VOL UP] or [VOL DOWN] button to
hear sound.
3. Switch MUTE off by using the [MUTE]
button.
4. Connect external speakers and adjust the
volume to a suitable level.
Some picture elements do not light up
Some pixels of the display may not turn on.
This monitor is manufactured using an extremely
high level of precision technology: however,
sometimes some pixels of the monitor may not
display. This is not a malfunction.
After-Images can still be seen on the monitor
after the monitor is powered off. (Examples
of still pictures include logos, video games,
computer images, and images displayed in 4:3
normal mode)
A still picture is displayed for an over extended
period of time
Do not allow a still image to be displayed for
an extended period of time as this can cause a
permanent after-image to remain on the monitor.
26
BDL3245E / BDL4245E / BDL4645E
8.
Technical Specifications (Need Check)
BDL3245E
Display
Item
Specifications
Screen Size (Active Area)
32” LCD
Aspect ratio
16:9
Number of pixels
1920 (H) x 1080 (V)
Pixel pitch
0.36375 (H) x 0.36375 (V) [mm]
Displayable colors
1.06B colors
Brightness (typical)
500 cd/m2
Dynamic contrast ratio
3000:1
Contrast ratio (typical)
1450:1
Viewing angle
178 degrees
In/Out Terminals
Item
Specifications
Speaker Output
Internal Speaker
10W (L) + 10W (R) [RMS]/8Ω 1 Way 1 Speaker System 82 dB/W/M/160 Hz ~ 13 KHz
Audio Output
RCA Jack x 1
0.5V [rms] (Normal)/ 2 Channel (L+R)
Audio Input
RCA Jack x 2
0.5V [rms] (Normal)/ 2 Channel (L+R)
RS232C
D-Sub Jack x 2 (9 pin)
TXD + RXD (1:1)
RJ-45
RJ-45 Jack x 1
(8 pin)
10/100 Lan Port
HDMI Input
HDMI Jack x 1 (Type A) (18 pin)
Digital RGB: TMDS (Video + Audio) MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel (L+R)
Supports LPCM only
DVI-D Input
DVI-D jack
Digital RGB: TMDS (Video)
VGA Input
D-Sub Jack x 1 (15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω) MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
VGA Output
D-Sub Jack x 1 (15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω) MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Component Input
RCA Jack x 1
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω) MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
General
Item
Specifications
Power Supply
AC 100 ~ 240V, 50 ~ 60Hz
Power Consumption (Max)
160W
Power Consumption (typ.)
140W
Power Consumption (Standby & Off)
<1W (RS232 in active)
Dimension (With Stand) [W x H x D]
1252.1 x 773.2 x 405.1 mm
Dimension (Without Stand) [W x H x D]
1252.1 x 722.9 x 121.8 mm
Weight (With Stand)
26.4 Kg
Weight (Without Stand)
38.7 Kg
Gross Weight
47.2 Kg
27
BDL3245E / BDL4245E / BDL4645E
Environmental Condition
Item
Temperature
Specifications
Operational
0 ~ 40°C
Storage
-20 ~ 60°C
Humidity
Operational
20 ~ 80% RH (No condensation)
Storage
5 ~ 95% RH (No condensation)
Pressure
Operational
795 ~ 1013 hPa (Altitude: 0 ~ 4,500 m)
Storage / Shipment
300 ~ 1013 hPa (Altitude: 0 ~ 9,000 m)
Internal Speaker
Item
Specifications
Type
1 Way 1 Speaker
Input
10 W (RMS)
Impedance
8Ω
Output Sound Pressure
82 dB/W/M
Frequency Response
160 Hz ~ 13 KHz
BDL4245E
Display
Item
Specifications
Screen Size (Active Area)
42” LCD
Aspect ratio
16:9
Number of pixels
1920 (H) x 1080 (V)
Pixel pitch
0.36375 (H) x 0.36375 (V) [mm]
Displayable colors
1.06B colors
Brightness (typical)
450 cd/m2
Dynamic contrast ratio
3000:1
Contrast ratio (typical)
4000:1
Viewing angle
178 degrees
In/Out Terminals
Item
Specifications
Speaker Output
Internal Speaker
10W (L) + 10W (R) [RMS]/8Ω 1 Way 1 Speaker System 82 dB/W/M/160 Hz ~ 13 KHz
Audio Output
RCA Jack x 1
0.5V [rms] (Normal)/ 2 Channel (L+R)
Audio Input
RCA Jack x 2
0.5V [rms] (Normal)/ 2 Channel (L+R)
RS232C
D-Sub Jack x 2 (9 pin)
TXD + RXD (1:1)
RJ-45
RJ-45 Jack x 1
(8 pin)
10/100 Lan Port
HDMI Input
HDMI Jack x 1 (Type A) (18 pin)
Digital RGB: TMDS (Video + Audio) MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel (L+R)
Supports LPCM only
DVI-D Input
DVI-D jack
Digital RGB: TMDS (Video)
VGA Input
D-Sub Jack x 1 (15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω) MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
VGA Output
D-Sub Jack x 1 (15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω) MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Component Input
RCA Jack x 1
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω) MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
28
BDL3245E / BDL4245E / BDL4645E
General
Item
Specifications
Power Supply
AC 100 ~ 240V, 50 ~ 60Hz
Power Consumption (Max)
260W
Power Consumption (typ.)
230W
Power Consumption (Standby & Off)
<1W (RS232 in active)
Dimension (With Stand) [W x H x D]
991.6 x 621 x 329.6 mm
Dimension (Without Stand) [W x H x D]
991.6 x 584 x 115.5 mm
Weight (With Stand)
24.7 Kg
Weight (Without Stand)
23 Kg
Gross Weight
28 Kg
Environmental Condition
Item
Temperature
Specifications
Operational
0 ~ 40°C
Storage
-20 ~ 60°C
Humidity
Operational
20 ~ 80% RH (No condensation)
Storage
5 ~ 95% RH (No condensation)
Pressure
Operational
795 ~ 1013 hPa (Altitude: 0 ~ 4,500 m)
Storage / Shipment
300 ~ 1013 hPa (Altitude: 0 ~ 9,000 m)
Internal Speaker
Item
Specifications
Type
1 Way 1 Speaker
Input
10 W (RMS)
Impedance
8Ω
Output Sound Pressure
82 dB/W/M
Frequency Response
160 Hz ~ 13 KHz
BDL4645E:
Display
Item
Specifications
Screen Size (Active Area)
46” LCD
Aspect ratio
16:9
Number of pixels
1920 (H) x 1080 (V)
Pixel pitch
0.36375 (H) x 0.36375 (V) [mm]
Displayable colors
1.06B colors
Brightness (typical)
400 cd/m2
Dynamic contrast ratio
3000:1
Contrast ratio (typical)
5000:1
Viewing angle
178 degrees
In/Out Terminals
Item
Specifications
Speaker Output
Internal Speaker
10W (L) + 10W (R) [RMS]/8Ω 1 Way 1 Speaker System 82 dB/W/M/160 Hz ~ 13 KHz
Audio Output
RCA Jack x 1
0.5V [rms] (Normal)/ 2 Channel (L+R)
Audio Input
RCA Jack x 2
0.5V [rms] (Normal)/ 2 Channel (L+R)
29
BDL3245E / BDL4245E / BDL4645E
RS232C
D-Sub Jack x 2 (9 pin)
TXD + RXD (1:1)
RJ-45
RJ-45 Jack x 1
(8 pin)
10/100 Lan Port
HDMI Input
HDMI Jack x 1 (Type A) (18 pin)
Digital RGB: TMDS (Video + Audio) MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel (L+R)
Supports LPCM only
DVI-D Input
DVI-D jack
Digital RGB: TMDS (Video)
VGA Input
D-Sub Jack x 1 (15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω) MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
VGA Output
D-Sub Jack x 1 (15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω) MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Component Input
RCA Jack x 1
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω) MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
General
Item
Specifications
Power Supply
AC 100 ~ 240V, 50 ~ 60Hz
Power Consumption (Max)
270W
Power Consumption (typ.)
250W
Power Consumption (Standby & Off)
<1W (RS232 in active)
Dimension (With Stand) [W x H x D]
1091.1 x 681.7 x 329.6 mm
Dimension (Without Stand) [W x H x D]
991.6 x 645.7 x 133 mm
Weight (With Stand)
26.7 Kg
Weight (Without Stand)
26 Kg
Gross Weight
31 Kg
Environmental Condition
Item
Specifications
Temperature
Humidity
Pressure
Operational
0 ~ 40°C
Storage
-20 ~ 60°C
Operational
20 ~ 80% RH (No condensation)
Storage
5 ~ 95% RH (No condensation)
Operational
795 ~ 1013 hPa (Altitude: 0 ~ 4,500 m)
Storage / Shipment
300 ~ 1013 hPa (Altitude: 0 ~ 9,000 m)
Internal Speaker
Item
Specifications
Type
1 Way 1 Speaker
Input
10 W (RMS)
Impedance
8Ω
Output Sound Pressure
82 dB/W/M
Frequency Response
160 Hz ~ 13 KHz
This LCD monitor supports HDMI CEC (Consumer Electronics Control) protocol through the OneWire function. This gives you the ability to control
your display through the HDMI connector using CEC commands. The command manual for this function is available separately.
NOTE:
Philips does not guarantee 100% interoperability with all HDMI CEC devices.
30
2011 © Koninklijke Philips Electronics N.V. All rights reserved.
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips Electronics N.V. and are used under license from
Koninklijke Philips Electronics N.V.
Specifications are subject to change without notice.