- Computers & electronics
- Computer components
- Chassis components
- Computer cases
- ZALMAN
- Z9 U3
- User's manual
Zalman Z9 U3 computer case User's manual
Add to My manuals11 Pages
ZALMAN Z9 U3 is a mid-tower ATX case designed to accommodate standard ATX and m-ATX motherboards, ATX or ATX12V power supplies, and full-size graphics cards up to 290mm in length. It features a简约 and stylish design with a black powder-coated finish, a mesh front panel for improved airflow, and a tempered glass side panel to showcase your build. The case comes with three pre-installed 120mm fans (one in the front, one in the rear, and one at the top), and it supports the installation of additional fans for improved cooling.
advertisement
ATX MID TOWER PC CASE
Ver 1.0
한 글
ENGLISH
User's Manual
English
Z9 U3
1
Cautionary Note
1) Please read this manual thoroughly prior to installation.
2) Before installing, check the components and condition of the product, and if any problem is found, contact the retailer.
3) Avoid inserting objects or hands into the system while it is in operation to prevent product damage and injuries.
4) Check the manual when connecting cables. Incorrect connections may cause short circuits leading to fire hazards.
5) Do not block the front intake vent or the rear exhaust vent.
6) Keep this unit away from heat sources, direct sunlight, water, oil, and humid environments, and place the unit on a flat, stable, vibration-free, and well-ventilated area.
7) Do not clean the product surface with chemicals or wet cloth.
(chemicals: industrial brightener, wax, benzene, alcohol, paint thinner, mosquito repellent, aromatics, lubricant, detergent etc.)
8) Please wear gloves while handling this product to prevent injuries.
9) Product design and specifications may be revised to improve quality and performance.
Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages due to external causes, including but not limited to, improper use, problems with electrical power, accident, neglect, alteration, repair, improper installation, or improper testing.
1
2
Z9 U3
2
Product Details
(1) Specifications
Models
Type
Dimensions (W×H×D)
Weight
Materials
Color
Motherboard Compatibility
Power Supply Compatibility
PCI/AGP Card Compatibility
5.25”
Drive Bays
3.5“
5.25"/3.5"/2.5”
Hot-swap
Expasion Card Solts
I/O Ports
Cooling
Components
Front
Top
Rear
Side
Bottom
Z9 U3
ATX Mid Tower
207(W) x 464(H) x 504(D)mm (8.1 x 18.2 x 19.8”)
7.2kg (15.8 lb)
Plastic, Steel
Black
Standard ATX / m-ATX
Standard ATX / ATX12V
Full Size 290㎜ (11.4")
External Bay x 3
External Bay x 1, Internal Bay x 5
1 (3in-1)
-
7 Slots
Headphones x 1, USB 2.0 x 2, Mic x 1, USB 3.0 x 2
120mm/140mm Fan Vent x 1 (1 Fan included)
120mm/140mm Fan Vent x 2
(1 Fan included, 1 optional)
120mm Fan Vent x 1 (1 Fan included)
-
120mm/140mm Fan Vent x 1 (Fan optional)
Z9 U3
(2) Parts
User manual
Main Unit Stand-Off × 5
Bolt A(#6-32*6mm) × 11
[PSU, PCI]
Bolt B(M3*5mm) × 17
[M/B, FDD, SSD]
Bolt C(M3*6mm) × 12
[5.25”Bay ODD]
Bolt D(#6-32*4mm) × 20
[3.5” Bay HDD]
Bolt E(#6-32*6mm) × 5
[3.5” HDD]
HDD Anti-vibration rubber
× 20
[3.5” Bay HDD]
PCI Slot × 2 CPU 12V Extension Cable × 1 Cable Tie × 5
3
Z9 U3
3
Installation
(1) Side Panel Removal
②
4
①
(2) Motherboard Installation
There are 4 Stand Offs preinstalled. Please refer to the diagrams below for additional Stand Off positions (based on motherboard type).
ATX Board m-ATX Board or
Stand-Off
B Bolt
(3) 5.25” and 3.5” Drive Installation
1) Front Cover Removal
Z9 U3
PULL
2) ODD Installation
3) 2.5” / 3.5” Tray Installation
① Tray removal
Bolt C
Bolt C
5
6
Z9 U3
② Attach Drive to Tray
A. 3.5” FDD Installation
3.5” FDD
B. 3.5” HDD Installation
3.5” HDD
Bolt B
C. 2.5” SSD Installation
SSD
Bolt A
Bolt B
(4) Front Cover Installation
When removing the front cover, the power switch and extension cable are separated to prevent disconnection. Be sure to connect them before installing the front cover.
B. 3.5” HDD Installation
Z9 U3
(5) 3.5” HDD Installation
HDD
Bolt D
HDD Antivibration rubber
When transporting an assembled system, please secure the HDD with
Bolt E as shown above.
Bolt E
(6) Cable Connection
Power Button
When removing HDD, pull the fastening lever outwards and then remove it.
Fan Connection or
Power LED
Mother Board or
PSU Power Mother Board
(3-Pin Fan Connector)
7
8
Z9 U3
I/O Port
MotherBoard MotherBorad I/O
※ Power and I / O ports to connect please refer to your motherboard. manual.
(7) 2.5” HDD / SSD Optional
2.5" HDD and SSDs can be installed on the right side of case as shown in the diagram below.
Bolt B
(8) Optional Fan Installation and Replacement
Top Panel Fan (120/140 mm) Installation
When installing fan, press the Top Panel’s eight Hook’s towards each other to remove and install as shown in diagram below. The Z9U3 comes with one
120mm Fan pre-installed.
8
Zalman Tech Co., Ltd.
#1007 daeryung Techno Town III, 448 Gasan-dong, Gumchun-gu, Seoul, 153-803,Korea
Tel: +82-2-2107-3232 / Fax: +82-2-2107-3322 / www.zalman.com / e-mail: [email protected]
Zalman USA, Inc.
10531 Garden Glove Blvd., Garden Grove, CA 92843, U.S.A
Tel: +1-714-530-0700 / Fax: +1-714-530-0707 / www.zalman.com / e-mail: [email protected]
advertisement
Key Features
- Midi Tower PC
- ATX, micro ATX
- Supported HDD sizes: 2.5,3.5"
- Number of 2.5" bays: 1 Number of 3.5" bays: 7 Number of 5.25" bays: 4
- Side window
- Plastic, Steel
- Black
Related manuals
advertisement