Your Phone
Torch
Headphone jack
Microphone
TFT LCD
Left soft key
Right soft key
Navigation and
Confirm keys
Pick-up key
Hang up and
power key
Message
Camera key
Alphanumeric
keypad
Charger,
USB port
Micro
Philips continuously strives to improve its products. Due to software
upgrading, some contents in this user guide may be different from your
product. Philips reserves the rights to revise this user guide or withdraw
it at any time without prior notice. Please take your product as standard.
1
Home screen
Your phone’s home screen consists of the following areas:
Status Bar
Shortcut
Keys
Learn about the main keys.
Icons
Definition
Function
Dial
Make or answer a call.
(
O
Confirm and Select or confirm an option;
navigation key Long press to turn on or off the torch.
Hang-up/
End a call;
)
Power/
Hold to turn on/off the phone;
Exit
Return to home screen.
Left soft key Select the options on the screen.
L
Right soft key Select the options on the screen.
L
Lock/unlock
Press L(left) and then * to lock keys on
*
home screen;
Long press * to unlock keys.
2
Icons & symbols
Learn about the icons and symbols on the screen.
Icons
Definition
Function
Ringtone
Your phone will ring when receiving a call.
Vibration Your phone will vibrate when receiving a call.
only
Battery
The bars indicate the battery level.
SMS
You have a new message.
Missed
call
You have missed a call.
Call
diverts
All your incoming voice calls are being
forwarded to a number.
Headset
The headset is plugged into the phone.
Alarm
The alarm clock is activated.
Roaming
Displayed when your phone is registered to a
network other than your own (especially when
you are abroad).
Home
zone
A zone designated by your network operator.
Contact your service provider for details.
GSM
network
Your phone is connected to a GSM network.
The more bars are shown the better the
reception is.
Key lock
The keypad has been locked.
Memory
card
The memory card is in use.
Auto
Power
Auto power function is enabled.
Flight
Mode
Flight mode is activated.
3
Getting started
Insert SIM card and Charge the battery
Learn about installing SIM card and charging the battery for the first use.
Insert SIM card
1 Remove the back cover.
2 Take out the battery.
3 Insert the SIM 1/SIM 2 card.
4 Install the battery.
5 Replace the back cover.
4
Charge the battery
A new battery is partially charged. The battery icon in the upper-right
corner shows the battery level of charging status.
Tips:
• You can use the phone while it is charging.
• Keeping the charger plugged to the mobile
phone when the battery is fully charged will
not damage the battery. The only way to
turn off the charger is to unplug it, so it is
advisable to use an easily accessible power
socket.
• If you do not intend to use your phone for
several days, we recommend that you
remove the battery.
• If a fully charged battery left unused, it will
lost its charge over time.
• If a battery is being used for the first time or
the battery has not been used for a
prolonged period, it may take longer time to
recharge.
Insert a Micro SD card (Memory card)
You can expand the memory of your
phone by adding a micro-SD card.
1 Unlock the memory card cover.
2 Align your micro-SD card with the
slot. Put it in place.
3 Press down the card holder and
pull it until it is locked.
5
Using your phone
Use basic call functions
Make a call
1 Enter the phone number.
2 Press (and select SIM1 or
3 Press )to hang up.
SIM2 to dial the number.
Tips:
• For international calls, long press 0 to enter the "+" sign for the international
prefix.
• To dial the number by using SIM 2, press LOptions, select Call (SIM2 voice call).
Answer and end a call
(to answer the call, press the navigation key + or - to adjust
the volume).
2 Press right soft key to select handsfree mode during a call.
3 Press )to hang up.
1 Press
Tips:
• You can use the supplied headset to answer or end a call.
Use speed dial
On the home screen, you can call a number by long pressing a numeric
key to choose a speed dial number and select SIM1 or SIM2 to call out.
To assign a contact to a speed-dial key:
1 Select Menu > Contacts > Phonebook settings > Speed dial.
2 Select Status to set speed dial On.
3 Select Set numbers to add numbers from phonebook.
Make an emergency call
Without a SIM card in phone, you can press numeric keys to make the
emergency call. In Europe, the standard emergency number is 112; in the
UK, it is 999.
6
Receive and send messages
You can use the Messaging menu to send text message.
1 Select Messaging> Write message.
2 Select Text message or Multimedia message, write your message.
3 Press LOptions>Send to to send the message.
Enter text
Your mobile phone supports a number of text entry methods, including
English input, numeric input and symbol input.
Keys:
Keys
Function
#
Select a input method.
*
Enter symbols and punctuations.
0
Insert a space.
L(Right)
Delete the previous character.
L(Left)
Select the character on the screen.
O
Select or confirm a character.
</>
To browse the candidate character on the previous or
next page.
Note:
• Depending on the language you select for your phone, the supported input methods
may vary.
7
Introduction of input methods:
Input method
English input
Function
Press the keys that are marked with the letter you
wish to enter. Press once to get the first letter on
the key, press twice quickly to get the second letter
and so on until the letter you want is displayed on
the screen.
Smart English You need to press only once on the key
input
corresponding to each letter needed to spell a word:
keystrokes input are analyzed and the word
suggested by input method is displayed at the popup window.
Numeric input
Press the numeric key to enter a number.
Manage your phonebook
Learn about basic phonebook function.
Add a new contact
1 Go to Contacts, select Add new contact.
2 Select a location. (To SIM1/To SIM2/To phone).
3 Enter the number, and add details as desired.
4 Press LOptions to finish saving.
Search for a contact
1 Go to Contacts.
2 Enter the first few letters of the name in the search bar.
3 Select the contact from the list.
Manage your contacts
You can copy or move contacts between the SIM card and phone, or
delete contacts. Go to Contacts, press + or - to select the desired
option.
8
MultiMedia
Audio player
Save MP3 music files to your Micro SD card and then insert the card to
your phone.
Play music
1 Go to Entertainment>Multimedia>Audio player, go to list to
select your desired song in the folder.
- To refresh the list, press LOptions> refresh list.
2 Press LOptions> Play to start playing.
3 Using the following keys to control playback:
Function
P
Q
N
L(Right)
)
Definition
Pause and resume playback.
Select previous track.
Select next track.
Press the navigation key + or - to adjust volume.
Return to the previous menu.
Go to the home screen.
Player settings
Go to Audio player>Options>Settings:
• Pre. playlist : Play audio files from your phone or memory card.
• List auto gen. : Generate playlist automatically.
• Repeat : Repeat One (Play current file repeatedly); Repeat All
(Play all the files in the folder repeatedly).
• Shuffle: Play music files in the folder randomly.
• Background play : Continue to play music after exiting the audio
player.
• Bluetooth settings : Switch on/off Bluetooth stereo output.
9
Press LBack or )to turn off the audio player.
Note:
• When listening to music, adjust the volume to a moderate level. Continuous exposure
to high volume may impair your hearing.
FM radio
Learn about listening to radio programs by using a FM radio.
Listen to a radio station
1 Plug the supplied headset into your phone.
2 Go to Multimedia>FM radio, press LOptions>Auto search. It
starts scanning automatically and save the available channels.
< or > to adjust the frequency.
4 Press + or - to adjust the volume.
5 Press LBack or )to turn off FM radio.
3 Press the navigation key
FM radio settings
Go to LOptions>Settings :
•
•
Background play: Continue playback after exiting FM radio.
loudspeaker : Listen to radio through the speaker.
Video recorder
You can record your video and save the file to your phone or SD card.
Record video
1 Go to Multimedia>Video recorder.
2 press O to start recording the video.
3 Press LStop to stop recording and save the file.
Camera
Learn about camera function. Let you take photos as desired by using
your phone.
10
Take a photo
1 Go to Multimedia>Camera.
2 Aim the lens at the subject.
- Press
brightness.
+/-
to zoom in or zoom out, press
</>
to adjust the
3 Press O or C to take a photo.
4 Press L(right) to exit.
Tips:
• All the photos taken are saved to My files >Phone or Memory card >Photos.
View photos
Tap L(left), go to Options>Photos>Image viewer, tap navigation keys
to select a photo.
Camera settings
Go to Camera>Options>Camera settings:
• Shutter sound : Select the shutter sound.
• EV : Select a explosure value.
• Anti-flicker : Select a band to avoid the impacts on photos caused
by flickers from lighting sources.
• Contrast : Adjust the contrast.
• Delay timer : Select a time span for auto photographing.
• Cont. shot : Set to take photos continuously.
Tools
Calendar
Go to Tools>Calendar, you can check the calendar.
Alarm
Learn about how to set and use an alarm. You can set up to five alarms.
11
Set an alarm
1 Go to Tools>Alarm.
2 Select an alarm, press LEdit to edit the alarm.
3 Press LDone to finish setting the alarm.
Turn off an alarm
1 Go to Tools>Alarm.
2 Select the alarm you want to turn off, press LEdit.
3 Press the navigation key or to select Off.
<
>
Stop an alarm
When the alarm rings,
•
•
Select Stop: The alarm stops.
Select Snooze: The alarm will sound again after the set Snooze
(min) interval.
Check world clock
Learn about how to check time & date of cities in other countries.
1 Go to Tools>World clock.
<
>
2 Press the navigation key or to select a city.
3 You can check time & date of the city.
Note:
• Alarms, reminders, programmed events are time zone independent.
Calculator
Use the numeric keys to calculate on the phone.
Set clock
1 On the home screen, go to Menu>Settings> Phone settings
>Time and date.
2 Select Set time/date: use the numeric key to enter the digits.
12
SNS
To use the SNS (Social Networking Services) function.
SIM settings
1 Check that your phone is turned on. Enter the PIN code if required.
2 Go to Settings>Dual SIM settings, select Dual SIM open/Only
SIM1 open/Only SIM2 open.
Profiles
The profiles are defined for several scenes. They consist of the settings
for ringtone, volume, and others. With preset profiles, you can easily
adjust the settings for incoming calls and messages as desired.
1 Go to Settings>User profiles, press
LOptions>Activate
to
activate the profile.
2 Go to Options>Customize to modify ringtone, volume and others.
To activate Silent mode, long press # on the home screen.
13
Settings
SIM settings
Function
Definition
Dual
SIM Select the dual SIM switch mode.
switch
Dual
SIM Select active mode to receive calls or message from a
settings
SIM card.
User profiles
Function
User profiles
Definition
Select the desired profile from the list of profiles and
tap O or LOptions > Activate to activate it.
Tap LOptions > Customize to adjust the profile
settings.
Phone settings
Function
Definition
Flight mode
Select Normal mode or Flight mode.
Time and date
Set the clock of the phone.
Auto power
Set time for the phone to be switched on/off
automatically.
Language
Select a language for your phone.
Pref. input method Select your preferred input method.
Fast key
Select a navigation key as direct access to a
menu.
Go to
Set the shortcut menu.
UART settings
Select data from SIM1/SIM2 when connect
phone with PC.
14
LCD backlight
Select the brightness of backlight.
Display
Select display options for your phone.
Wallpaper
Select an image as the wall paper of your
phone.
Screen saver
Enter screen saver mode after a time span.
Power on display
Select the power on animation.
Power off display
Select the power off animation.
Show date and time
Select whether to show date and time on the
home screen.
Network settings
Function
Network
selection
Definition
Select the network for your phone (service
subscription
dependent).
Automatic
is
recommended.
Security settings
This menu allows you to use passwords to protect your SIM card,
phone, and information stored on the phone.
Function
SIM1/SIM2
security
PIN lock
Definition
This option allows you to use passwords to
protect your SIM card.
Set PIN password protection for your SIM card. (The
PIN or PIN2 are provided by the network operator.)
Change PIN/ Change your PIN/PIN2 password as desired.
PIN2
Phone
This option allows you to use passwords to
security
protect your phone.
15
Phone lock
Set passowrd protection for your phone. You are
required to enter the password each time you turn on
the phone or change to a new SIM card (1122 by default).
Change your phone password as desired.
Change
password
Auto
Set an time span for the keypad to be locked.
keypad lock
Note:
• The PIN code is preconfigured and communicated to you by your network operator or
retailer.
• If you enter an incorrect PIN code three times in succession, your SIM card will be
blocked. To unblock it, you must request the PUK code from your operator.
• If you enter an incorrect PUK code ten times in succession, the SIM card will be locked
permanently. When this happens, please contact your network operator or retailer.
Restore factory settings
Function
Restore
factory
settings
Definition
Restore your phone settings to the default values. You
need to enter your phone lock password (1122 by
default).
Call settings
Go to Menu>Calls>Call settings.
Function
Definition
SIM1/SIM2
call settings
Go to SIM1/SIM2 call settings.
Call waiting
Get informed of an incoming call when on the phone
(network-dependent).
Call divert
Divert incoming calls to your voice mailbox or
another phone number.
Call barring
Set limits to your incoming and outgoing calls.
16
Line switching
Select a phone line.
Advanced
settings
Go to advanced settings.
Blacklist
This option allows you to reject the incoming calls or
messages from those included in the blacklist.
Auto redial
Call
reminder
Keep redialing the number that fails to go through.
time Get reminded after the call time span once or
repeatedly.
Reject by SMS
Reject the incoming call by sending SMS to the
number.
Answer mode
Select an answer mode, any key answer or auto
answer when headset mode.
17
Safety & Precaution
Precaution
Keep your phone away from small children
Keep your phone and all accessories out of the reach of small children. Small parts may cause
choking or serious injury if swallowed.
Radio Waves
Your phone transmits/receives radio waves in the GSM frequency (900/1800MHz).
Check with the vehicle manufacturer that electronic equipment used in your vehicle will not be
affected by radio energy.
Switch off your phone...
Turn off the phone when in an aircraft. The use of mobile phones in an aircraft may be dangerous
for the operation of the aircraft, disrupt the mobile phones network and may be illegal.
In hospitals, clinics, other health care centers and anywhere else where you may be in the close
vicinity of medical equipment.
In areas with a potentially explosive atmosphere (e.g. petrol stations and also areas where the
air contains dust particles, such as metal powders).In a vehicle transporting flammable products
or a vehicle powered by liquefied petroleum gas (LPG).In quarries or other areas where blasting
operations are in progress.
Your mobile phone and your car
Avoid using your phone while driving and obey all regulations that restrict the use of mobile
phones while driving. Use hands free accessories to increase your safety when possible. Ensure
that your phone and car kit do not block any air bags or other security devices fitted in your car.
Handle your phone carefully and sensibly
For the optimal and satisfactory operation of the phone you are recommended to use the
phone in the normal operating position.
• Do not expose your phone to extreme temperatures.
• Do not immerse the phone in any liquid; if your phone is damp, switch it off, remove the battery
and let them dry for 24hrs before using them again.
• To clean the phone, wipe it with a soft cloth.
Protect batteries from damage
You should only use Philips Authentic Accessories, as the use of any other accessories may
damage your phone and may be dangerous, and will make all guarantees for your Philips phone
null and void. The use of an unspecified type of battery may also cause an explosion.
Make sure damaged parts are replaced immediately by a qualified technician and that they are
replaced with genuine Philips replacement parts.
• Your phone is powered by a rechargeable battery.
• Use specified charger only.
• Do not incinerate.
• Do not deform or open the battery.
• Do not allow metal objects (such as keys in your pocket) to short circuit the battery contacts.
• Avoid exposure to excessive heat (>60° C or 140° F), moisture or caustic environments.
Environmental care
Remember to observe the local regulations regarding the disposal of the packaging materials,
exhausted batteries and old phone and please promote their recycling.Philips has marked the
battery and packaging with standard symbols designed to promote the recycling and appropriate
disposal of your eventual waste.
:The labeled packaging material is recyclable.
:A financial contribution has been made to the associated national packaging recovery and
recycling system.
18
:The plastic material is recyclable (also identifies the type of plastic).
WEEE Marking in the DFU: “Information to the Consumer”
Disposal of your old product
Your product is designed and manufactured with high quality materials and components, which can
be recycled and reused.
When this crossed-out wheeled bin symbol is attached to a product it means the product is
covered by the European Directive 2002/96/EC
Please inform yourself about the local separate collection system for electrical and electronic
products.
Please act according to your local rules and do not dispose of your old products with your normal
household waste. The correct disposal of your old product will help prevent potential negative
consequences for the environment and human health.
This device may contain commodities, technology or software subject to export laws and regulations
from the US and other countries. Diversion contrary to law is prohibited.
Tips
Pacemakers
If you have a pacemaker:
• Always keep the phone more than 15 cm from your pacemaker when the phone is switched on,
in order to avoid potential interference.
• Do not carry the phone in a breast pocket.
• Use the ear opposite to the pacemaker to minimize the potential interference.
• Switch off your phone if you suspect that interference is taking place.
Hearing aids
If you are a user of a hearing aid, consult your physician and hearing aid manufacturer to learn
whether your particular device is susceptible to cellular phone interference.
How to prolong the battery life of your phone
To have your mobile phone function properly, sufficient battery power is important. For the powersaving purpose, do the following, if applicable:
• Turn off the Bluetooth function of your phone.
• Set the backlight level and duration of your phone to a low value.
• Turn on the auto keypad lock, turn off the key sounds, tap vibration, or vibration alerts.
• Establish GPRS connection when needed. Otherwise, your phone will keep searching for GPRS
connection, and drain your battery power.
• Turn off your phone if there is no coverage. Otherwise, the phone will keep searching for
network, and drain your battery power.
Troubleshooting
The phone does not switch on
Remove/reinstall the battery. Then charge the phone until the battery icon stops scrolling. Unplug
the charger and try to switch the mobile on.
The display shows BLOCKED when you switch on the phone
Somebody tried to use your phone but didn’t know the PIN code nor the unblocking code (PUK).
Contact your service provider.
The display shows IMSI failure
This problem is related to your subscription. Contact your operator.
Your phone doesn’t return to idle screen
Long press the hang-up key or switch off the phone, check that the SIM card and the battery are
installed correctly and switch it on again.
19
The network symbol is not displayed
The network connection is lost. Either you are in a radio shadow (in a tunnel or between tall
buildings) or you are outside the network coverage area. Try from another place, try to reconnect
to the network (especially when abroad), check that the antenna is in place if your mobile has an
external antenna, or contact your network operator for assistance/information.
The display doesn’t respond (or the display responds slowly) to key presses
The display responds more slowly at very low temperatures. This is normal and does not affect the
operation of the phone. Take the phone to a warmer place and try again. In other cases please
contact your phone supplier.
Your battery seems to over heat
You might be using a charger that was not intended for use with your phone. Make sure you always
use the Philips authentic accessory shipped with your phone.
Your phone doesn’t display the phone numbers of incoming calls
This feature is network and subscription dependent. If the network doesn’t send the caller’s number,
the phone will display Call 1 or Withheld instead. Contact your operator for detailed information on
this subject.
You can’t send text messages
Some networks don’t allow message exchanges with other networks. First check that you have
entered the number of your SMS centre, or contact your operator for detailed information on this
subject.
You can’t receive and/or store JPEG pictures
A picture may not be accepted by your mobile phone if it is too large, if its name is too long, or if it
doesn’t have the correct file format.
You feel that you have missed some calls
Check your call divert options.
When charging, the battery icon shows no bar and the outline is flashing
Only charge the battery in an environment where the temperature does not go below 0°C (32°F) or
above 50°C (113°F).
In other cases please contact your phone supplier.
The display shows SIM failure
Check that the SIM card has been inserted correctly. If the problem persists, your SIM card may be
damaged. Contact your operator.
When attempting to use a feature in the menu, the display shows NOT ALLOWED
Some features are network dependent. They are only available, therefore, if the network or your
subscription supports them. Contact your operator for detailed information on this subject.
The display shows INSERT YOUR SIM CARD
Check that the SIM card has been inserted correctly. If the problem persists, your SIM card may be
damaged. Contact your operator.
The autonomy of your phone seems lower than indicated on the user guide
The autonomy is linked to your settings (e.g., ringer volume, backlight duration) and the features you
use. To increase the autonomy, and whenever possible, you must deactivate features you do not use.
Your phone doesn’t work well in your car
A car contains many metallic parts that absorb electromagnetic waves which can affect the phone’s
performance. A car kit is available to provide you with an external antenna and enables you to make
and receive phone calls without handling the handset.
Note:
• Check with the local authorities whether or not you are allowed to use the phone while driving.
20
Your phone is not charging
If the battery is completely flat, it might take several minutes of pre-charge (up to 5 minutes in some
cases) before the charging icon is displayed on the screen.
The picture captured with the phone camera is not clear
Make sure that the camera lens on both sides is clean.
Trademark Declaration
Philips
PHILIPS and PHILIPS’ Shield Emblem are registered trademarks of Koninklijke
Philips Electronics N.V. manufactured by Shenzhen Sang Fei Consumer
Communications Co., Ltd. Under license from Koninklijke Philips Electronics N.V..
Specific Absorption Rate Information
International standards
THIS MOBILE PHONE MEETS THE INTERNATIONAL RECOMMENDATIONS FOR EXPOSURE
TO RADIO WAVES
Your mobile phone is a radio transmitter and receiver. It is designed and manufactured not to exceed
the limits for exposure to radio frequency (RF) energy defined by the international standards. These
recommendations have been established by the International Commission on Non-Ionizing Radiation
Protection (ICNIRP) and, the Institute of Electrical and Electronics Engineers (IEEE) that forecast a
substantial safety margin for assuring the protection of all persons, regardless of age and health.
The exposure recommendations for mobile phones use a measurement unit known as the Specific
Absorption Rate (SAR). The SAR limit recommended by the ICNIRP for the mobile phones used by
the general public is 2.0W/kg averaged over ten grams of tissue and, is 1,6W/kg averaged over one
gram of tissue by IEEE Std 1528 for the head.
Tests for SAR have been conducted using recommended operating positions with the mobile phone
transmitting at its highest certified power level in all tested frequency bands. Although the SAR is
determined at the highest certified power level, the actual SAR levels of the mobile phone while
operating are generally below the maximum SAR value. This is because the phone is designed to
operate at multiple power levels so as to use only the power required to reach the network. In
general, the closer you are to a base station antenna, the lower the power output.
While there may be differences between the SAR levels of various phones and at various positions,
they all meet the international protection standards for exposure to radio waves.
The highest SAR value for this E122 model phone when tested for compliance against
the standard was 0.596 W/kg for ICNIRP recommendation.
For limiting the radio waves exposure, it is recommended to reduce the mobile phone call duration
or to use a headset. The purpose of those precautions is to take the mobile phone away from the
head and the body.
Limited warranty
1 What Does This Limited Warranty Cover?
Philips warrants to the original retail purchaser (“Consumer” or “You”) that this Philips cellular
product and all accessories originally provided by Philips in the sales package (“Product”) are free
from defects in materials, design and workmanship under normal use in accordance with the
operating instructions and pursuant to the following terms and conditions. This limited warranty
extends only to the Consumer for Products purchased and used in the original country of purchase.
The limited warranty is valid only in Philips’ intended country of sales of the product.
2. How Long is The Limited Warranty Period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase
of the Product, documented by valid proof of purchase. The limited warranty for original Philips
rechargeable battery extends for six (6) months from the date of purchase.
21
3. What Will Philips Do if The Product is Not Free From Material Defects in Materials and
Workmanship During The Limited Warranty Period?
During the limited warranty period, Philips or its authorized service representative will, at its option
either repair or replace, without charge for parts or labour, a materially defective Product with new
or refurbished parts or Product and return such repaired or replaced Product to the Consumer in
working condition. Philips will retain defective parts, modules or equipment.
Repaired or replaced Product will be covered by this limited warranty for the balance of the original
limited warranty period or ninety (90) days from the date of repair or replacement whichever is
longer. Repair or replacement of Product, at Philips’ option is your exclusive remedy.
4. What is Not Covered By This Limited Warranty?
This limited warranty does not cover:
a) Product that has been subjected to misuse, accident, shipping or other physical damage, improper
installation, abnormal operation handling, neglect, inundation, fire, water or other liquid intrusion; or
b) Product that has been damaged due to repair, alteration, or modification by anyone not authorized
by Philips; or
c) Product that has reception or operation problems caused by signal conditions, network reliability
or cable or antenna systems; or
d) Product defects or problems caused by uses with non-Philips products or accessories; or
e) Product which warranty/quality stickers, product serial number or electronic serial number has
been removed, altered or rendered illegible; or
f) Product purchased, used, serviced, or shipped for repair from outside the original country of
purchase, or used for commercial or institutional purposes (including but not limited to Products
used for rental purposes); or
g) Product returned without valid proof of purchase or which proof of purchase has been altered or
is illegible.
h)Normal wear and tear or Force Majeure.
5. How Do You Get Warranty Service?
a) Return the Product to an authorized service center of Philips. You may contact the local Philips
office for the location of the nearest authorized service center.
b)The SIM card must be removed from the Product before it is given to Philips. Philips assumes no
liability for damaged or loss of the SIM card or the data contained therein.
c)If the Product failure is not covered by this limited warranty, or this limited warranty is inapplicable,
void or invalid due to any terms and conditions stated herein, the Consumer will be charged for the
cost of repair or replacement of the Product and all other related cost incurred in repairing or
replacing the Product.
d) IMPORTANT - you are required to return the Product together with a valid proof of purchase
which must identify the point of purchase, date of purchase, Product model and Product serial
number clearly.
6. Other Limitation: This Warranty is The Entire Agreement.
EXCEPT FOR THE EXPRESS WARRANTIES SET FORTH ABOVE AND THOSE IMPLIED BY LAW
AND WHICH CANNOT BE EXCLUDED OR MODIFIED BY AGREEMENT, PHILIPS PROVIDES
NO OTHER WARRANTY WHETHER EXPRESS OR IMPLIED (WHETHER BY STATUTE, UNDER
THE OPERATION OF LAW OR OTHERWISE) AND SPECIALLY DISCLAIMS ANY WARRANTY
OF SATISFACTORY QUALITY MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
PHILIPS’ TOTAL LIABILITY FOR DAMAGES RELATING TO OR ARISING OUT OF THE
PURCHASE OR USE OF THE PRODUCT, REGARDLESS OF THE TYPE OR CAUSE OF SUCH
DAMAGE OR THE FORM OR CHARACTERISATION OF THE CLAIM ASSERTED (E.G.
CONTRACT OR TOPIT), SHALL NOT EXCEED THE ORIGINAL PURCHASE PRICE PAID FOR
THE PRODUCT.
22
HOWEVER IN NO EVENT SHALL PHILIPS BE LIABLE FOR ANY PUNITIVE, SPECIAL,
INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED
TO THE LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERIAL LOSS, LOST PROFITS,
LOST BUSINESS OPPORTUNITIES, COST OF SUBSTITUTION OF GOODS OR SERVICES,
INVESTMENTS, DAMAGE TO GOODWILL OR REPUTATION, OR LOSS OF DATA AND
CLAIMS BY THIRD PARTIES) RESULTING FROM PURCHASE OR USE OF THE PRODUCT, TO
THE FULLEST EXTENT ALLOWED BY LAW, WHETHER OR NOT PHILIPS HAS BEEN ADVISED
OF THE POSSIBILTY OF SUCH DAMAGES. THESE LIMITATIONS SHALL APPLY
NOTWITHSTANDING THE FAILURE OF THE ESSENTIAL PURPOSE OF ANY LIMITED REMEDY.
This limited warranty represents the complete and exclusive agreement between the Consumer and
Philips with respect to this cellular Product and it supercedes all prior agreements between the
parties, oral or written, and all other communications between the parties relating to the subject
matter of this limited warranty. No carrier, retailer, agent, dealer, employee, thereof, or employee
of Philips is authorized to make modifications to this limited warranty and you should not rely on any
such representation.
This limited warranty does not affect the Consumer’s statutory rights under applicable national laws
in force.
Declaration of Conformity
We,
Shenzhen Sang Fei Consumer
Communications Co., Ltd.
11 Science and Technology Road,
Shenzhen Hi-tech Industrial Park,
Nanshan District, Shenzhen 518057
China
declare under our sole responsibility that the product
E122
Philips GSM/GPRS 900/1800
TAC number: 86313701
to which this declaration relates, is in conformity with the following Standards:
SAFETY : EN 60950-1:2006+A11:2009
HEALTH: EN 50360:2001
EN 62209-1:2006
EN 62209-2:2010
EMC:
ETSI EN 301 489-1 V1.8.1
ETSI EN 301 489-7 V1.3.1
SPECTRUM: ETSI EN 301 511 V9.0.2
We hereby declare that all essential radio test suites have been carried out and that the above named
product is in conformity to all the essential requirements of Directive 1999/5/EC.
The conformity assessment procedure referred to in Article 10 and detailed in Annex IV of Directive
1999/5/EC has been followed with the involvement of the following Notified Body:
SIEMIC ,2206 Ringwood Avenue,San Jose,C,USA
Identification mark: 2200
December 13 th, 2011
Quality Manager
23