Register your product and get support at
www.philips.com/welcome
HTS3582
HTS3592
1
2
3
5
Important
2
Safety
Care for your product
Care of the environment
3D health warning
Help and support
2
3
3
3
3
Your home theater
4
4
4
5
6
Main unit
Connectors
Remote control
Connect and set up
6
Connect speakers
6
Connect to TV
7
Connect audio from TV and other devices 8
Set up speakers
9
Set up EasyLink (HDMI-CEC control)
9
Connect and set up a home network
10
4
Use your home theater
Access the home menu
Discs
Data files
USB storage devices
Audio, video, and picture options
Radio
MP3 player
Browse PC through DLNA
Karaoke
Choose sound
11
11
11
13
13
14
15
15
15
16
16
Change settings
17
17
18
18
18
18
18
19
19
Language settings
Picture and video settings
Audio settings
Parental control settings
Display settings
Energy saving settings
Speaker settings
Restore default settings
Update software
Check software version
Update software through USB
Update software through the Internet
19
19
19
20
7
Product specifications
20
8
Troubleshooting
23
Notice
25
25
25
25
9
Copyright
Compliance
Open source software
RMVB end user agreement (Asia Pacific
and China only)
Trademarks
10 Index
25
26
27
EN
1
English
Contents
1
Important
Read and understand all instructions before you
use your product. If damage is caused by failure to
follow instructions, the warranty does not apply.
Safety
Risk of electric shock or fire!
• Never expose the product and accessories to
rain or water. Never place liquid containers,
such as vases, near the product. If liquids are
spilt on or into the product, disconnect it
from the power outlet immediately. Contact
Philips Consumer Care to have the product
checked before use.
• Never place the product and accessories
near naked flames or other heat sources,
including direct sunlight.
• Never insert objects into the ventilation slots
or other openings on the product.
• Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
• Disconnect the product from the power
outlet before lightning storms.
• When you disconnect the power cord, always
pull the plug, never the cable.
Risk of short circuit or fire!
• Before you connect the product to the
power outlet, ensure that the power voltage
matches the value printed on the back or
bottom of the product. Never connect the
product to the power outlet if the voltage is
different.
Risk of injury or damage to the home theater!
• For wall-mountable products, use only the
supplied wall mount bracket. Secure the
wall mount to a wall that can support the
combined weight of the product and the
wall mount. Koninklijke Philips Electronics
N.V. bears no responsibility for improper wall
mounting that results in accident, injury or
damage.
• For speakers with stands, use only the
supplied stands. Secure the stands to the
speakers tightly. Place the assembled stands
on flat, level surfaces that can support the
combined weight of the speaker and stand.
2
EN
•
Never place the product or any objects
on power cords or on other electrical
equipment.
• If the product is transported in temperatures
below 5°C, unpack the product and wait until
its temperature matches room temperature
before connecting it to the power outlet.
• Visible and invisible laser radiation when
open. Avoid exposure to beam.
• Do not touch the disc optical lens inside the
disc compartment.
• Parts of this product can be made of glass.
Handle with care to avoid injury and damage.
Risk of overheating!
• Never install this product in a confined space.
Always leave a space of at least four inches
around the product for ventilation. Ensure
curtains or other objects never cover the
ventilation slots on the product.
Risk of contamination!
• Do not mix batteries (old and new or carbon
and alkaine, etc.).
• Danger of explosion if batteries are
incorrectly replaced. Replace only with the
same or equivalent type.
• Remove batteries if they are exhausted or if
the remote control is not to be used for a
long time.
• Batteries contain chemical substances, they
should be disposed of properly.
Risk of swallowing batteries!
• The product/remote control may contain
a coin/button type battery, which can be
swallowed. Keep the battery out of reach of
children at all times! If swallowed, the battery
can cause serious injury or death. Severe
internal burns can occur within two hours of
ingestion.
• If you suspect that a battery has been
swallowed or placed inside any part of the
body, seek immediate medical attention.
• When you change the batteries, always
keep all new and used batteries out of
reach of children. Ensure that the battery
compartment is completely secure after you
replace the battery.
• If the battery compartment cannot be
completely secured, discontinue use of the
product. Keep out of reach of children and
contact the manufacturer.
3D health warning
•
If you or your family has a history of epilepsy
or photosensitive seizures, consult a medical
professional before exposing yourself to flashing
light sources, rapid image sequences or 3D
viewing.
To avoid discomfort such as dizziness, headache or
disorientation, we recommend not watching 3D
for extended periods of time. If you experience
any discomfort, stop watching 3D and do not
immediately engage in any potentially hazardous
activity (for example driving a car) until your
symptoms have disappeared. If symptoms persist,
do not resume watching 3D without consulting a
medical professional first.
Parents should monitor their children during 3D
viewing and ensure they do not experience any
discomfort as mentioned above. Watching 3D is
not recommended for children under six years of
age as their visual system is not fully developed yet.
•
•
•
Do not insert any objects other than discs
into the disc compartment.
Do not insert warped or cracked discs into
the disc compartment.
Remove discs from the disc compartment
if you are not using the product for an
extended period of time.
Use only microfiber cloth to clean the
product.
Care of the environment
Your product is designed and manufactured with
high quality materials and components, which can
be recycled and reused.
Help and support
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC. Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and do not
dispose of your old products with your normal
household waste.
Correct disposal of your old product helps to
prevent potential negative consequences for the
environment and human health.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot be
disposed with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries because correct
disposal helps to prevent negative consequences
for the environmental and human health.
Philips provides extensive online support. Visit our
website at www.philips.com/support to:
• download the complete user manual
• print the quick start guide
• watch video tutorials (available only for
selected models)
• find answers to frequently answered
questions (FAQs)
• email us a question
• chat with our support representative.
Follow the instructions on the website to select
your language, and then enter your product model
number.
Alternatively, you can contact Philips Consumer
Care in your country. Before you contact Philips,
note down the model number and serial number
of your product. You can find this information on
the back or bottom of your product.
EN
3
English
Care for your product
2
Your home theater
Congratulations on your purchase, and welcome
to Philips! To fully benefit from the support that
Philips offers, register your product at www.philips.
com/welcome.
a
•
•
(USB)
Audio, video or picture input from a USB
storage device.
Connect to a Wi-Fi dongle (Model:
Philips WUB1110, sold separately).
b MIC
Audio input from a microphone.
c MUSIC iLINK
Audio input from an MP3 player.
Main unit
Rear connectors
This section includes an overview of the main unit.
FM
ANTENNA
a Disc compartment
b Display panel
c
d
Connect to the power supply.
(Open/Close)
Open or close the disc compartment, or
eject the disc.
b AUDIO IN-AUX
(Play/Pause)
Start, pause or resume play.
c VIDEO OUT
e SOURCE
f
a AC MAINS
Connect to an analog audio output on the TV
or an analog device.
Connect to the composite video input on
the TV.
Select an audio or video source for the home
theater.
d HDMI OUT (ARC)
(Standby-On)
Switch the home theater on or to standby.
e LAN
Connectors
Connect to the HDMI input on the TV.
Connect to the LAN input on a broadband
modem or router.
f DIGITAL IN-OPTICAL
Connect to an optical audio output on the
TV or a digital device.
This section includes an overview of the
connectors available on your home theater.
g DIGITAL IN-COAXIAL
Front connectors
h ANTENNA FM
Connect to a coaxial audio output on the TV
or a digital device.
Signal input from an antenna. (Fixed FM
antenna for some models)
i SPEAKERS
Connect to the supplied speakers and
subwoofer.
4
EN
This section includes an overview of the remote
control.
(Home)
Access the home menu.
c Source buttons
• DISC/POP-UP MENU : Switch to disc
source.Access or exit the disc menu
when you play a disc.
RADIO : Switch to FM radio.
AUDIO SOURCE : Select an audio input
source.
•
•
1
d
2
3
14
4
15
5
English
b
Remote control
•
•
BACK
Return to a previous menu screen.
In radio mode, press and hold to erase
the current preset radio stations.
e Navigation buttons
• Navigate menus.
• In radio mode, press left or right to start
auto search.
In radio mode, press up or down to tune
the radio frequency.
•
6
f OK
7
16
17
8
Confirm an entry or selection.
g
9
18
10
11
13
•
h
19
12
20
•
•
•
/
(Previous/Next)
Skip to the previous or next track,
chapter or file.
In radio mode, select a preset radio station.
(Stop) / (Eject/Open/Close)
Stop play.
Press and hold for three seconds to open
or close the disc compartment, or eject
the disc.
i
/
(Fast Backward / Fast Forward)
Search backwards or forward. Press
repeatedly to change the search speed.
j
+/- (Volume)
Increase or decrease volume.
k
SOUND SETTINGS
Access or exit sound options.
21
l Alphanumeric buttons
Enter values or letters (using SMS style entry).
m REPEAT
Select or turn off repeat mode.
a
•
•
(Standby-On)
Switch the home theater on or to standby.
When EasyLink is enabled, press and hold
for at least three seconds to switch all
connected HDMI CEC compliant devices
to standby.
n TOP MENU
Access the main menu of a disc.
o
OPTIONS
Access more play options while playing a
disc or a USB storage device.
• In radio mode, set a radio station.
•
EN
5
p
(Play)
Start or resume play.
q
(Pause)
Pause play.
r
(Mute)
Mute or restore volume.
s AUDIO
Select an audio language or channel.
3
Connect and set up
This section helps you connect your home theater
to a TV and other devices, and then set it up.
For information about the basic connections of
your home theater and accessories, see the quick
start guide. For a comprehensive interactive guide,
visit www.connectivityguide.philips.com.
t SUBTITLE
Select subtitle language for video.
u Color buttons
Select tasks or options for Blu-ray discs.
Note
• For identification and supply ratings, see the type
plate at the back or bottom of the product.
• Before you make or change any connections,
make sure that all devices are disconnected from
the power outlet.
Connect speakers
The speaker cables are color-coded for easy
connection. To connect a speaker to your home
theater, match the color on the speaker cable to
the color on the connector.
Speaker position plays a critical role in setting up
a surround sound effect. For best effect, position
all the speakers towards the seating position and
place them close to your ear level (seated).
6
EN
• Surround sound depends on factors such as
room shape and size, type of wall and ceiling,
windows and reflective surfaces, and speaker
acoustics. Experiment with the speaker positions
to find the optimum setting for you.
Follow these general guidelines for speakers placement.
Seating position:
This is the center of your listening area.
FRONT CENTER (front center) speaker:
Place the center speaker directly in front of the
seating position, either above or below your TV.
FRONT LEFT (front left) and FRONT
RIGHT (front right) speakers:
Place the left and right speakers in the front, and
at equal distance from the center speaker. Make
sure that the left, right, and the center speakers
are at equal distance from your seating position.
REAR LEFT (rear left) and REAR RIGHT
(rear right) speakers:
Place the rear surround speakers to the left
and right side of your seating position, either
in line with it or slightly behind it.
SUBWOOFER (subwoofer):
Place the subwoofer at least one meter
to the left or right of the TV. Leave about
10-centimeter clearance from the wall.
2
The HDMI ARC connector on the TV
might be labeled differently. For details,
see the TV user manual.
On your TV, turn on HDMI-CEC operations.
For details, see the TV user manual.
• If you cannot hear the TV audio through
your home theater, set up the audio
manually (see 'Set up the audio' on page 10).
1
2
TV
3
4
5
Connect to TV
Connect your home theater to a TV to watch
videos. You can listen to the TV audio through your
home theater speakers.
Use the best quality connection available on your
home theater and TV.
Option 1: Connect to TV through HDMI
(ARC)
Best quality video
Your home theater supports HDMI version 1.4 Audio Return Channel (ARC). If your TV is HDMI
ARC compliant, you can hear the TV audio through
your home theater by using a single HDMI cable.
Using a High Speed HDMI cable, connect
the HDMI OUT (ARC) connector on your
home theater to the HDMI ARC connector
on the TV.
1
Option 2: Connect to TV through
standard HDMI
Best quality video
If your TV is not HDMI ARC compliant, connect
your home theater to the TV through a standard
HDMI connection.
Using a High Speed HDMI cable, connect the
HDMI OUT (ARC) connector on your home
theater to the HDMI connector on the TV.
Connect an audio cable to hear the TV audio
through your home theater (see 'Connect
audio from TV and other devices' on page 8).
On your TV, turn on HDMI-CEC operations.
For details, see the TV user manual.
• If you cannot hear the TV audio through
your home theater, set up the audio
manually (see 'Set up the audio' on page 10).
1
2
3
Note
• If your TV has a DVI connector, you can use an
HDMI/DVI adapter to connect to TV. However,
some of the features may not be available.
TV
EN
7
English
•
Note
Option 3: Connect to the TV through
composite video
Option 1: Connect audio through a digital
optical cable
Basic quality video
If your TV does not have HDMI connectors, use
a composite video connection. A composite
connection does not support high-definition video.
Using a composite video cable, connect the
VIDEO connector on your home theater to
the VIDEO IN connector on the TV.
• The composite video connector might
be labeled AV IN, COMPOSITE, or
BASEBAND.
Connect an audio cable to hear the TV audio
through your home theater (see 'Connect
audio from TV and other devices' on page 8).
When you watch TV programs, press
SOURCE on your home theater repeatedly
to select the correct audio input.
When you watch videos, switch your TV to
the correct video input. For details, see the
TV user manual.
Best quality audio
Using an optical cable, connect the OPTICAL
connector on your home theater to the
OPTICAL OUT connector on the TV or
other device.
• The digital optical connector might be
labeled SPDIF or SPDIF OUT.
1
1
TV
2
3
4
TV
Option 2: Connect audio through a digital
coaxial cable
Good quality audio
Using a coaxial cable, connect the COAXIAL
connector on your home theater to the
COAXIAL/DIGITAL OUT connector on the
TV or other device.
• The digital coaxial connector might be
labeled DIGITAL AUDIO OUT.
1
Connect audio from TV and
other devices
Play audio from TV or other devices through your
home theater speakers.
Use the best quality connection available on your
TV, home theater, and other devices.
Note
• When your home theater and TV are connected
through HDMI ARC, an audio connection is not
required (see 'Option 1: Connect to TV through
HDMI (ARC)' on page 7).
8
EN
Option 3: Connect audio through analog
audio cables
Basic quality audio
Using an analog cable, connect the AUX
connectors on your home theater to the AUDIO
OUT connectors on the TV or other device.
1
Enable EasyLink
Set up speakers
Set up the speakers manually to experience
customized surround sound.
Before you start
Make the necessary connections described in the
quick start guide, and then switch the TV to the
correct source for your home theater.
1
2
3
4
Press (Home).
Select [Setup], and then press OK.
Select [Audio] > [Speaker setup]
Enter the distance for each speaker, and
then listen to the test tones and change
the volume. Experiment with the speaker
positions to find the ideal setting.
Set up EasyLink (HDMI-CEC
control)
This home theater supports Philips EasyLink,
which uses the HDMI-CEC (Consumer Electronics
Control) protocol. EasyLink-compliant devices that
are connected through HDMI can be controlled
by a single remote control.
Note
1
2
3
4
Press (Home).
Select [Setup], and then press OK.
Select [EasyLink] > [EasyLink] > [On] .
On your TV and other connected devices,
turn on HDMI-CEC control. For details, see
the user manual of the TV or other devices.
• On your TV, set the audio output to
'Amplifier' (instead of TV speakers). For
details, see the TV user manual.
EasyLink controls
With EasyLink, you can control your home theater,
TV, and other connected HDMI-CEC compliant
devices with a single remote control.
• [One Touch Play] (One-touch play): When a
video disc is in the disc compartment, press
(Play) to wake up the TV from standby, and
then play a disc.
• [One Touch Standby] (One-touch standby):
If one-touch standby is enabled, your home
theater can switch to standby with the
remote control of the TV or other HDMICEC devices.
• [System Audio Control] (System audio
control): If system audio control is enabled,
the audio of the connected device is output
through your home theater speakers
automatically when you play the device.
• [Audio Input Mapping] (Audio input
mapping):If system audio control does not
work, map the connected device to the
correct audio input connector on your home
theater (see 'Set up the audio' on page 10).
• Depending on the manufacturer, HDMI-CEC is
known by many names. For information on your
device, see the user manual of the device.
• Philips does not guarantee 100% interoperability
with all HDMI-CEC devices.
Note
• To change the EasyLink control settings, press
(Home), select [Setup] > [EasyLink].
EN
9
English
VCR
Before you start
• Connect your home theater to the HDMICEC compliant device through HDMI
connection.
• Make the necessary connections described in
the quick start guide, and then switch the TV
to the correct source for your home theater.
Set up the audio
Set up the wired network
If you cannot hear the audio output of a
connected device through your home theater
speakers, check that you have enabled Easylink on
all the devices (see 'Enable EasyLink' on page 9).
Then, set up the EasyLink audio control.
Press (Home).
Select [Setup], and then press OK.
Select [EasyLink] > [System Audio Control]
> [On].
• To play the audio from the TV speakers,
select [Off], and skip the following steps.
Select [EasyLink] > [Audio Input Mapping].
Follow the onscreen instructions to map the
connected device to the audio inputs on your
home theater.
• If you connect your home theater to the
TV through an HDMI ARC connection,
make sure that the TV audio is mapped
to the ARC input on your home theater.
What you need
• A network cable (RJ45 straight cable).
• A network router (with DHCP enabled).
1
2
3
LAN
4
5
Connect and set up a home
network
Connect your home theater to a network router
through wired or wireless network connection,
and enjoy:
• Streamed multimedia content
• BD-Live applications
• Software update
Caution
• Familiarize yourself with the network router,
media server software and networking
principles. If necessary, read documentation that
accompanies the network components. Philips
is not responsible for lost, damaged, or corrupt
data.
Before you start
• For software updates, make sure that the
network router has access to the Internet
with high-speed connection and is not
restricted by firewalls or other security
systems.
• Make the necessary connections described in
the quick start guide, and then switch the TV
to the correct source for your home theater.
10
EN
www
1
2
3
4
5
6
Using a network cable, connect the LAN
connector on your home theater to the
network router.
Press (Home).
Select [Setup], and then press OK.
Select [Network] > [Network installation]
> [Wired (Ethernet)].
Follow the onscreen instructions to complete
the setup.
• If connection fails, select [Retry], and
then press OK.
Select [Finish], and then press OK to exit.
• To view the network settings, select
[Setup] > [Network] > [View network
settings].
4
Use your home theater
Your home theater is Wi-Fi ready. Connect a Wi-Fi
dongle for easy access to a wireless network.
What you need
• A network router (with DHCP enabled). For
best wireless performance, coverage, and
compatibility, use 802.11n router;
• Connect a Wi-Fi dongle (Model: Philips
WUB1110, sold separately) to the
connector on your home theater.
This section helps you use the home theater to
play media from a wide range of sources.
Before you start
• Make the necessary connections described in
the Quick start guide and the user manual.
• Switch the TV to the correct source for the
home theater.
Access the home menu
The home menu provides easy access to
connected devices, setup and other useful features
in your home theater.
Press (Home).
» The home menu is displayed.
1
2
1
2
3
4
5
Press (Home).
Select [Setup], and then press OK.
Select [Network] > [Network installation]
> [Wireless (Wi-Fi)], and then press OK.
Follow the onscreen instructions to select
and set up the wireless network.
• If connection fails, select [Retry], and
then press OK.
Select [Finish], and then press OK to exit.
• To view the network settings, select
[Setup] > [Network] > [View wireless
settings].
3
Press the Navigation buttons and OK to
select the following:
• [play Disc]: Start disc play.
• [browse USB]: Access the USB content
browser
• [browse PC]: Access the computer
content browser.
• [Setup]: Access menus to change video,
audio and other settings.
Press (Home) to exit.
Discs
Your home theater can play DVDs, VCDs, CDs, and
Blu-ray discs. It can also play discs that you’ve made
at home, such as CD-R discs of photos and music.
Insert a disc into the home theater.
If the disc does not play automatically, press DISC
or select [play Disc] from the home menu.
Use the remote control to control play (see
'Remote control' on page 5).
• It is normal to hear a little noise when
you play a Blu-ray disc. This does not
mean that your home theater is faulty.
1
2
3
Note
• To avoid flickering, change the brightness of the
display.
EN
11
English
Set up the wireless network
Play buttons
Button
Navigation
buttons
OK
(Play)
/
/
AUDIO
SUBTITLE
DISC/
POP-UP
MENU
OPTIONS
REPEAT
Action
Navigate menus.
Up/Down: Rotate the picture
clockwise or counter-clockwise.
Left/Right: Flip the picture vertically
or horizontally.
Confirm an entry or selection.
Start or resume play.
Pause play.
Stop play.
Skip to the previous or next track,
chapter or file.
When a video is paused, search
backwards or forward.
Select an audio language or channel.
Select subtitle language for video.
Access or exit the disc menu.
1
2
3
Bonus View on Blu-ray
On Blu-ray discs that support the Bonus View,
enjoy extra content such as commentaries in a
small screen window. Bonus View is also known as
picture-in-picture.
Enable Bonus View in the Blu-ray disc menu.
While you play the movie, press OPTIONS.
» The options menu is displayed.
1
2
3
Access the advanced options when
you play your audio, video, or media
files (see 'Audio, video, and picture
options' on page 14).
Select or turn off repeat mode.
Using the high speed HDMI cable, connect
your home theater to a 3D compatible TV.
Make sure that the 3D video setting is
enabled. Press (Home), select [Setup] >
[Video] > [Watch 3D video] > [Auto].
• To play 3D discs in 2D mode, select [Off].
Play a Blu-ray 3D disc and put on the 3D glasses.
• During video search and in certain play
modes, the video is displayed in 2D. The
video display returns to 3D when you
resume play.
4
5
Select [PIP selection] > [PIP].
• Depending on the video, PIP menu [1] or
[2] is displayed.
• To disable Bonus View, select [Off].
Select [2nd audio language] or [2nd Subtitle
Language].
Select the language, and then press OK.
Synchronize picture and sound
BD-Live on Blu-ray
If the audio and video are not synchronized, delay
the audio to match the video.
Press SOUND SETTINGS.
Select AUD SYNC, and then press OK.
Press the Navigation buttons (up/down) to
synchronize the audio with the video.
Press OK to confirm.
Access additional features on the Blu-ray discs with
BD-Live content, such as internet chats with the
director, the latest movie trailers, games, wallpaper,
and ringtones.
BD-Live services and content vary from disc to disc.
What you need
• Blu-ray disc with BD-Live content
• a USB storage device, with at least 1 GB of
memory
Play Blu-ray 3D disc
1
1
2
3
4
Your home theater can play Blu-ray 3D video. Read
the 3D health warning before playing a 3D disc.
What you need
• A 3D TV.
• A pair of 3D glasses that are compatible with
your 3D TV.
• A 3D Blu-ray video
• A high speed HDMI cable (preferably version
1.4)
12
EN
2
3
4
Connect your home theater to a home
network with Internet access (see 'Connect
and set up a home network' on page 10).
Connect a USB storage device to your home
theater.
Press (Home) and select [Setup].
Select [Advanced] > [BD-Live security] >
[Off] to enable BD-Live.
• To disable BD-Live, select [On].
6
Select the BD-Live icon in the disc menu, and
then press OK.
» BD-Live starts to load. The loading time
depends on the disc and your internet
connection.
Press the Navigation buttons to navigate BDLive, and then press OK to select an option.
Note
• To clear the memory on the storage device,
press (Home), select [Setup] > [Advanced]
> [Clear memory].
Data files
Your home theater can play pictures, audio and
video files contained in a disc or a USB storage
device. Before you play a file, check that the file
format is supported by your home theater (see
'File formats' on page 20).
Play the files from a disc or USB storage device.
To stop play, press .
• To resume the video from where you
stopped, press (Play).
• To play the video from the start, press .
1
2
Note
• To play DivX DRM protected files, connect your
home theater to a TV through an HDMI cable.
Subtitles
If your video has subtitles in multiple languages,
select a subtitle language.
Note
• Make sure that the subtitle file has the exact
same name as the video file. For example, if the
video file is named 'movie.avi', name the subtitle
file as 'movie.srt' or 'movie.sub'.
• Your home theater supports the following file
formats: .srt, .sub, .txt, .ssa, .ass, smi, and .sami. If
the subtitles do not appear correctly, change the
character set.
1
While playing video, press SUBTITLE to
select a language.
For DivX or RMVB/RM videos, if the subtitles
do not appear correctly, continue the
following steps to change the character set.
Press OPTIONS.
» The options menu is displayed.
Select [Character set], and then select a
character set that supports the subtitle.
Asia Pacific and China
2
3
4
Character
Set
[Standard]
[Chinese]
[ChineseTraditional]
[Korean]
Language
Albanian, Danish, Dutch, English,
Finnish, French, Gaelic, German,
Italian, Kurdish (Latin), Norwegian,
Portuguese, Spanish, Swedish,Turkish
Simplified Chinese
Traditional Chinese
English and Korean
VOD code for DivX
Before you purchase DivX videos and play them
on your home theater, register the home theater
on www.divx.com using the DivX VOD code.
Press (Home).
Select [Setup], and then press OK.
Select [Advanced] > [DivX® VOD Code].
» The DivX VOD registration code for
your home theater is displayed.
1
2
3
USB storage devices
Enjoy pictures, audio, and video stored on a USB
storage device such as an MP4 player or digital camera.
What you need
• A USB storage device that is formatted for
FAT or NTFS file systems, and complies with
the Mass Storage Class.
• A media file in one of the supported file
formats (see 'File formats' on page 20).
Note
• If you use a USB extension cable, USB HUB, or
USB multi-reader, the USB storage device may
not be recognized.
EN
13
English
5
1
2
3
4
5
Connect a USB storage device to the
(USB) connector on your home theater.
Press (Home).
Select [browse USB], and then press OK.
» A content browser is displayed.
•
Select a file, and then press OK.
Press the play buttons to control play (see
'Play buttons' on page 12).
•
•
•
•
•
•
•
•
Audio, video, and picture options
•
Use advanced features when you play pictures, audio
and video files from a disc or a USB storage device.
•
•
Audio options
While playing audio, repeat an audio track, a disc,
or a folder.
Press OPTIONS repeatedly to cycle through
the following functions:
• RPT TRK / RPT FILE: Repeat the current
track or file.
• RPT DISC / RPT FOLD: Repeat all the
tracks on the disc or the folder.
• RPT RDOM: Play audio tracks in random
order.
• RPT OFF: Turn off the repeat mode.
•
1
Video options
While watching video, select options such as
subtitles, audio language, time search, and picture
settings. Depending on the video source, some
options are not available.
Press OPTIONS.
» The video options menu is displayed.
1
2
14
Press the Navigation buttons and OK to
select and change:
• [Audio language]: Select audio language
for video.
• [Subtitle Language]: Select subtitle
language for video.
• [Subtitle shift]: Change the subtitle
position on the screen.
• [Info]: Display information about what is
playing.
• [Character set]: Select a character set
that supports the DivX subtitle.
EN
[Time search]: Skip to a specific part of the
video by entering the time of the scene.
[2nd audio language]: Select the second
audio language for Blu-ray video.
[2nd Subtitle Language]: Select the second
subtitle language for Blu-ray video.
[Titles]: Select a specific title.
[Chapters]: Select a specific chapter.
[Karaoke]: Change the karaoke settings.
[Angle list]: Select a different camera angle.
[Menus]: Display the disc menu.
[PIP selection]: Display Picture-in-Picture
window when playing a Blu-ray disc that
supports the Bonus View.
[Zoom]: Zoom into a video scene or
picture. Press the Navigation buttons
(left/right) to select a zoom factor.
[Repeat]: Repeat a chapter or title.
[Repeat A-B]: Mark two points within a
chapter or track to repeat play, or turn
off the repeat mode.
[Picture settings]: Select a predefined
color setting.
Picture options
While viewing a picture, zoom into the picture,
rotate it, add animation to a slideshow, and change
the picture settings.
Press OPTIONS.
» The picture options menu appears.
1
2
Press the Navigation buttons and OK to
select and change the following settings:
• [Rotate +90]: Rotate the picture 90
degree clockwise.
• [Rotate -90]: Rotate the picture 90
degree counter-clockwise.
• [Zoom]: Zoom into a video scene or
picture. Press the Navigation buttons
(left/right) to select a zoom factor.
• [Info]: Display picture information.
• [Duration per slide]: Select the display
speed for each picture in a slide show.
• [Slide animation]: Select animation for
the slide show.
• [Picture settings]: Select a predefined
color setting.
• [Repeat]: Repeat a selected folder.
If the picture and audio files are from the same
disc or USB storage device, you can create a
musical slideshow.
Select an audio track, and then press OK.
Press
BACK, and go to the picture folder.
Select a picture, and then press (Play) to
start the slideshow.
Press to stop slideshow.
Press again to stop music.
1
2
3
Button
/
or
Alphanumeric
buttons
Navigation
buttons
4
5
Note
BACK
OPTIONS
• Make sure that the picture and audio formats
are supported by your home theater (see 'File
formats' on page 20).
Radio
SUBTITLE
Action
Select a preset radio station.
English
Musical slideshow
Left/Right: Search for a radio station.
Up/Down: Fine tune a radio
frequency.
Press to stop the installation of
radio stations.
Press and hold to erase the
preset radio station.
Manual:
OPTIONS. 2) Press
1) Press
/ to select your preset. 3)
OPTIONS again to
Press
store the radio station.
Automatic: Press and hold for
three seconds to reinstall the
radio stations.
Toggle between the stereo and
mono sounds.
Listen to FM radio on your home theater, and
store up to 40 radio stations.
MP3 player
Note
• AM and digital radio are not supported.
• If no stereo signal is detected, or if fewer than
five stations are found, you are prompted to
install the radio stations again.
1
2
3
Connect the FM antenna to the ANTENNA FM
on your home theater (if not already connected).
• For the best reception, place the antenna
away from the TV or other sources of
radiation.
Press RADIO.
» If you have already installed the radio
stations, the last channel that you listened
to is played.
» If you have not installed any radio
stations, the message AUTO
INSTALL...PRESS PLAY appears on
the display panel. Press (Play).
Use the remote control to listen or to
change radio stations.
Connect a MP3 player to play audio files.
What you need
• An MP3 player.
• A 3.5mm stereo audio cable.
1
2
3
Using the 3.5mm stereo audio cable, connect
the MP3 player to the MUSIC iLINK
connector on your home theater.
Press AUDIO SOURCE repeatedly until
MUSIC I-LINK appears on the display panel.
Press the buttons on the MP3 player to select
and play audio files.
Browse PC through DLNA
Access and play the pictures, audio and video files
from a computer or media server on the home
network through your home theater.
Before you start
• Install a DLNA-compliant media server
application on your device. Make sure that
you download an application that works best
for you. For example,
EN
15
•
1
2
3
4
5
6
7
•
•
Windows Media Player 11 or higher for PC
Twonky Media Server for Mac or PC
Enable media sharing of files. For details,
check the user manual of the media server
software software.
Connect your home theater to a home
network. For better video quality, use wired
connection whenever possible.
Connect the computer and other DLNAcompatible devices to the same home network.
Press (Home).
Select [browse PC], and then press OK.
» A content browser is displayed.
Select a device on the network.
» The folders in the selected device are
displayed. Depending on the media
server, the folder names may vary.
• If you cannot see the folders, make sure
that you enable media sharing on the
selected device so that the content is
available for sharing.
Select a file, and then press OK.
• Some media files may not play due
to compatibility issues. Check the file
formats supported by your home theater.
Press the play buttons to control play (see
'Play buttons' on page 12).
Karaoke
Available only in selected model and region
Play a Karaoke disc on your home theater and sing
along with the music.
What you need
• A Karaoke microphone.
• Karaoke discs.
3
4
5
6
turn the microphone volume to the minimum
before you connect the microphone to your
home theater.
1
2
16
Connect a karaoke microphone to the MIC
connector on your home theater.
Switch your TV to the correct source for
your home theater.
EN
Select [Karaoke], and then press OK.
» The karaoke setup menu is displayed.
Press the Navigation buttons (up/down) and
OK to change the following settings:
• [Microphone]: Turn the microphone on
or off.
• [Microphone volume]: Change the
microphone volume.
• [Echo]: Change the echo level.
• [Key]: Change the pitch to match your voice.
Choose sound
This section helps you choose the ideal sound for
your video or music.
Press SOUND SETTINGS.
Press the Navigation buttons (left/ right) to
access the sound options on the display.
1
2
Sound settings Description
SOUND
Select a sound mode.
SURROUND Select surround sound or stereo
sound.
TREBLE
Change the high frequency output.
MID
Change the middle frequency output.
BASS
Change the low frequency output.
AUD SYNC
Delay the audio to match the video.
3
4
Caution
• To prevent loud feedback or unexpected noise,
Make sure that audio post processing is
enabled on your home theater (see 'Speaker
settings' on page 19).
While playing a karaoke disc, press OPTIONS.
» The options menu is displayed.
Select an option, and then press OK.
Press
BACK to exit.
If you do not press a button within a minute,
the menu exits automatically.
Sound mode
Select predefined sound modes to suit your video
or music.
Press SOUND SETTINGS.
Select SOUND, and then press OK.
Press the Navigation buttons (up/down) to
select a setting on the display:
• MOVIE: Enjoy a cinematic audio
experience, specially enhanced for movies.
1
2
3
4
MUSIC: Recreate the original recording
environment of your music, in the studio
or at a concert.
• ORIGINAL: Experience the original
sound of your movies and music, without
added sound effects.
• NEWS: Hear every word with optimized
speech and clear vocals.
• GAMING: Enjoy thrilling arcade sounds,
ideal for action-packed video games or
loud parties.
Press OK to confirm.
5
The home theater settings are already configured
for optimal performance. Unless you have a reason
to change a setting, we recommend that you keep
the default setting.
Note
• You cannot change a setting that is grayed out.
• To return to the previous menu, press
BACK. To exit the menu, press
Surround sound mode
Experience an immersive audio experience with
surround sound modes.
Press SOUND SETTINGS.
Select SURROUND, and then press OK.
Press the Navigation buttons (up/down) to
select a setting on the display:
• AUTO: Surround sound based on the
audio stream.
• MULTI-CH: Immersive multi-channel
sound for an enhanced movie
experience.
• STEREO: Two-channel stereo sound. Ideal
for listening to music.
Press OK to confirm.
1
2
3
4
Change settings
(Home).
Language settings
1
2
3
4
Press (Home).
Select [Setup], and then press OK.
Select [Preference], and then press OK.
Press the Navigation buttons and OK to
select and change:
• [Menu language]: Select a display
language for menu.
• [Audio]: Select an audio language for discs.
• [Subtitle]: Select a subtitle language for discs.
• [Disc menu]: Select a menu language for
discs.
Note
• If your preferred disc language is not available,
select [Others] from the list, and enter the
4-digit language code found at the end of this
user manual.
• If you select a language that is not available on a
disc, the home theater uses the default language
of the disc.
EN
17
English
•
Picture and video settings
Parental control settings
1
2
3
4
1
2
3
4
Press (Home).
Select [Setup], and then press OK.
Select [Video], and then press OK.
Press the Navigation buttons and OK to
select and change:
• [TV display]: Select a picture format to fit
the TV screen.
• [HDMI video]: Select the resolution of
video signal that is output from HDMI OUT
(ARC) on your home theater.To enjoy the
selected resolution, make sure that your TV
supports the selected resolution.
• [HDMI Deep Color]: Recreate the natural
world on your TV screen by displaying
vivid images using billion colors.Your home
theater must be connected to a Deep
Color enabled TV through an HDMI cable.
• [Picture settings]: Select pre defined
color settings for the video display.
• [Watch 3D video]: Set HDMI video to
support 3D or 2D video.
Display settings
1
2
3
4
Note
• If you change a setting, make sure that the TV
supports the new setting.
Audio settings
1
2
3
4
18
Press (Home).
Select [Setup], and then press OK.
Select [Audio], and then press OK.
Press the Navigation buttons and OK to
select and change:
• [Night mode]: For quiet listening,
decrease the volume of loud sounds on
your home theater. Night mode is only
available for Dolby-encoded DVD and
Blu-ray discs.
• [HDMI Audio]: Set the HDMI audio
output from your TV, or disable HDMI
audio output from the TV.
EN
Press (Home).
Select [Setup], and then press OK.
Select [Preference], and then press OK.
Press the Navigation buttons and OK to
select and change:
• [Change Password]: Set or change your
password for parental control access.
If you do not have a password or have
forgotten your password, enter 0000.
• [Parental control]: Restrict access to
discs that are recorded with age ratings.
To play all discs, irrespective of the ratings,
select 8 or [Off].
Press (Home).
Select [Setup], and then press OK.
Select [Preference], and then press OK.
Press the Navigation buttons and OK to
select and change:
• [Auto subtitle shift]: Enable or disable
automatic repositioning of subtitles on
TVs that support this feature.
• [Display panel]: Set the brightness of the
home theater front panel display.
• [VCD PBC]: Enable or disable the content
menu navigation of VCD and SVCD discs
with Play Back Control feature.
Energy saving settings
1
2
3
4
Press (Home).
Select [Setup], and then press OK.
Select [Preference], and then press OK.
Press the Navigation buttons and OK to
select and change:
• [Screen saver]: Switch the home theater
to screen saver mode after 10 minutes
of inactivity.
• [Auto standby]: Switch the home theater
to standby after 30 minutes of inactivity.
This timer works only when a disc or
USB play is paused or stopped.
• [Sleep timer]: Set the duration of the sleep
timer so that the home theater is switched
to standby after the specified period.
1
2
3
4
Press (Home).
Select [Setup], and then press OK.
Select [Advanced], and then press OK.
Press the Navigation buttons and OK to
select and change:
• [Enhanced audio]: Select [On] to enable
audio post processing at the speaker and
enable karaoke settings (if your product
supports Karaoke). To play the original
audio of the disc, select [Off].
Tip
• Enable audio post processing before you select a
6
Update software
Philips continually tries to improve its products.
To get the best features and support, update your
home theater with the latest software.
Compare the version of your current software with
the latest version on www.philips.com/support. If
the current version is lower than the latest version
available on the Philips support website, upgrade
your home theater with the latest software.
Caution
• Do not install a lower version of software than
the current version installed on your product.
Philips is not liable for problems caused due to
software downgrade.
predefined sound mode (see 'Sound mode' on page
16).
Restore default settings
Check software version
1
2
3
Check the version of the current software installed
on your home theater.
Press (Home).
Select [Setup], and then press OK.
Select [Advanced] > [Version information].
» The software version is displayed.
4
Press (Home).
Select [Setup], and then press OK.
Select [Advanced] > [Restore default
settings], and then press OK.
Select [OK], and then press OK to confirm.
» Your home theater is reset to its default
settings except for some settings such
as parental control and DivX VOD
registration code.
1
2
3
Update software through USB
What you need
• A USB flash drive that is FAT or NTFSformatted, with at least 75MB of memory. Do
not use a USB hard drive.
• A computer with Internet access.
• An archive utility that supports the ZIP file
format.
Step 1: Download the latest software
1
2
3
Connect a USB flash drive to your computer.
In your web browser, go to www.philips.com/
support.
At the Philips Support website, find your
product and locate the Software and drivers.
» The software update is available as a zip file.
EN
19
English
Speaker settings
4
5
6
Save the zip file in the root directory of your
USB flash drive.
Use the archive utility to extract the software
update file in the root directory.
» The files are extracted under the UPG_
ALL folder of your USB flash drive.
Disconnect the USB flash drive from your
computer.
Step 2: Update the software
7
Product
specifications
Note
• Specifications and design are subject to change
without notice.
Caution
• Do not switch off the home theater or remove
the USB flash drive during the update.
1
2
3
4
5
Connect the USB flash drive containing the
downloaded file to your home theater.
• Make sure that the disc compartment is
closed and no disc inside.
Press (Home).
Select [Setup], and then press OK.
Select [Advanced] > [Software update] > [USB].
Follow the onscreen instructions to confirm
the update.
» Once complete, the home theater
automatically switches off and restarts. If
it does not, disconnect the power cord
for a few seconds and then reconnect it.
Update software through the
Internet
1
2
3
4
5
20
Connect your home theater to a home
network with a high-speed Internet access
(see 'Connect and set up a home network'
on page 10).
Press (Home).
Select [Setup], and then press OK.
Select [Advanced] > [Software update] >
[Network].
» If an upgrade media is detected, you are
prompted to start or cancel the update.
Follow the onscreen instructions to confirm
the update.
» Once complete, the home theater
automatically switches off and restarts. If
it does not, disconnect the power cord
for a few seconds and then reconnect it.
EN
Region codes
The type plate on the back or bottom of the
home theater shows which regions it supports.
China
Country
DVD
BD
C
Media formats
•
•
AVCHD, BD, BD-R/ BD-RE, BD-Video, DVDVideo, DVD+R/+RW, DVD-R/-RW, DVD+R/-R
DL, CD-R/CD-RW, Audio CD,Video CD/SVCD,
Picture files, MP3 media, WMA media, DivX
Plus HD media, USB storage device
RMVB (Available only in Asia Pacific and China)
File formats
•
•
•
Audio: .aac, .mka, .mp3, .wma, .wav, .mp4, .m4a
Video:
• .avi, .divx, .mp4, .mkv, .asf, .wmv, .mpg, .mpeg,
• .rmvb, .rm (Available only in Asia Pacific
and China)
Picture: .jpg, .jpeg, .gif, .png
Audio formats
Your home theater supports the following audio
files.
Extension
Container
.mp3
MP3
Audio
codec
MP3
Bit rate
32 kbps ~
320 kbps
Container
.wma
ASF
.aac
AAC
.wav
.m4a
.mka
WAV
MKV
MKA
.mka
MKA
.mka
.mka
.mka
MKA
MKA
MKA
.mka
MKA
.mka
MKA
Audio
codec
WMA
Bit rate
64 kbps ~
160 kbps
AAC, HE- 192 kbps
AAC
PCM
1.4 Mbps
AAC
192 kbps
PCM
27.648
Mbps
Dolby
640 kbps
Digital
DTS core 1.54 Mbps
MPEG
912 kbps
MP3
32 kbps ~
320 kbps
WMA
64 kbps ~
160 kbps
AAC,
192 kbps
HE-AAC
.divx files in AVI container
Audio
codec
PCM,
Dolby
Digital,
MP3,
WMA
Audio
codec
PCM,
Dolby
Digital,
DTS
core,
MP3,
WMA
Video codec
Bit rate
DivX 3.11, DivX 4.x,
DivX 5.x, DivX 6.x
10 Mbps max
MPEG 1, MPEG 2
MPEG 4 ASP
H.264/AVC
HP@4.1/4.0;
MP@3.2/3.1/3.0
WMV9
20 Mbps (peak
40 Mbps)
10 Mbps max
20 Mbps (peak
40 Mbps)
20 Mbps
Bit rate
DivX 3.11,
DivX 4.x, DivX 5.x,
DivX 6.x
10 Mbps max
MPEG 1, MPEG 2
20 Mbps
(peak 40
Mbps)
10 Mbps max
MPEG 4 ASP
.mp4 or .m4v files in MP4 container
Audio
codec
Dolby
Digital,
MPEG,
MP3, AAC,
HE-AAC
Video formats
If you have a high definition TV, your home theater
allows you to play your video files with:
• Resolution: 1920 x 1080 pixels at
• Frame rate: 6 ~ 30 frames per second.
.avi files in AVI container
Video codec
Video codec
Bit rate
MPEG 1, MPEG
2
20 Mbps (peak
40 Mbps)
MPEG 4 ASP
H.264/AVC
HP@4.1/4.0;
MP@3.2/3.1/3.0
10 Mbps max
20 Mbps (peak
40 Mbps)
.mkv files in MKV container
Audio codec
PCM, Dolby
Digital, DTS
core, MPEG,
MP3, WMA,
AAC, HEAAC
Video codec
MPEG 1,
MPEG 2
Bit rate
20 Mbps (peak
40 Mbps)
MPEG 4 ASP
H.264/AVC
HP@4.1/4.0;
MP@3.2/3.1/3.0
WMV9
10 Mbps max
20 Mbps (peak
40 Mbps)
20 Mbps
.asf and .wmv files in ASF container
Audio
codec
PCM,
Dolby
Digital,
MP3, WMA
Video codec
Bit rate
MPEG 4 ASP
10 Mbps max
EN
21
English
Extension
Audio
codec
Video codec
Bit rate
H.264/AVC
HP@4.1/4.0;
MP@3.2/3.1/3.0
WMV9
20 Mbps (peak
40 Mbps)
Radio
•
20 Mbps
Tuning range:
• Europe/Russia/China: FM 87.5-108 MHz
(50 kHz)
• Asia Pacific/Latin America: FM 87.5-108
MHz (50/100 kHz)
Signal-to-noise ratio: FM > 45 dB
Frequency response: FM 180 Hz-12.5 kHz /
±3 dB
.mpg and .mpeg files in PS container
•
•
Audio
codec
PCM, DTS
core, MPEG,
MP3
USB
Video codec
Bit rate
MPEG 1,
MPEG 2
20 Mbps (peak 40
Mbps)
MPEG 1,
MPEG 2
20 Mbps (peak 40
Mbps)
.rm and .rmvb files in RM container (Available
only in Asia Pacific and China)
Audio codec
AAC,
COOK
Video
codec
RV30, RV40
Bit rate
20 Mbps (peak 40
Mbps)
Amplifier
•
•
•
•
Total output power: 600W RMS (30% THD)
Frequency response: 20 Hz-20 kHz / ±3 dB
Signal-to-noise ratio: > 65 dB (CCIR) /
(A-weighted)
Input sensitivity:
• AUX: 2 V
• Music iLink: 1 V
Video
•
•
Signal system: PAL / NTSC
HDMI output: 480i/576i, 480p/576p, 720p,
1080i, 1080p, 1080p24
Audio
•
•
•
22
S/PDIF Digital audio input:
• Coaxial: IEC 60958-3
• Optical: TOSLINK
Sampling frequency:
• MP3: 32 kHz, 44.1 kHz, 48 kHz
• WMA: 44.1 kHz, 48 kHz
Constant bit rate:
• MP3: 32 kbps - 320 kbps
• WMA: 48 kbps - 192 kbps
EN
•
•
•
•
Compatibility: Hi-Speed USB (2.0)
Class support: USB Mass Storage Class
(MSC)
File system: FAT16, FAT32, NTFS
Maximum memory support: < 160 GB
Main unit
•
•
•
•
•
Power supply: 220-240 V~, 50 Hz
Power consumption: 110 W
Standby power consumption: 0.9 W - 0.5 W
Dimensions (WxHxD): 360 x 58 x 325 mm
Weight: 2.62 kg
Subwoofer
•
•
•
•
•
Output power: 100 W RMS (30% THD)
Impedance: 4 ohm
Speaker drivers: 133 mm (5.25") woofer
Dimensions (WxHxD): 160 x 267.5 x 265 mm
Weight: 2.55 kg
Speakers
Center speaker:
• Output power: 100 W RMS (30% THD)
• Speaker impedance: 4 ohm
• Speaker drivers: 1 x 63.5 mm (2.5") woofer
• Dimensions (WxHxD): 160 x 85 x 95 mm
• Weight: 0.37 kg
Front/Rear speaker:
• Output power: 4 x 100 W RMS (30% THD)
• Speaker impedance: 4 ohm
• Speaker drivers: 1 x 76.2 mm (3") twin driver
• Dimensions (WxHxD):
• Speakers: 85 x 160 x 95mm
• Tall speakers: 240 x 1007 x 240 mm
• Weight:
• Speakers: 0.35 kg/each
• Tall speakers: 1.57 kg/each
Remote control batteries
2 x AAA-R03-1.5 V
Laser
•
•
•
Troubleshooting
Laser Type (Diode): InGaN/AIGaN (BD),
AIGaInP (DVD/CD)
Wave length: 405 +7 nm/-7 nm (BD), 655
+10 nm/-10 nm (DVD), 790 +10 nm/-20 nm
(CD)
Output power (Max. ratings): 20 mW (BD), 6
mW (DVD), 7 mW (CD)
English
•
8
Warning
• Risk of electric shock. Never remove the casing
of the product.
To keep the warranty valid, never try to repair the
product yourself.
If you have problems using this product, check the
following points before you request service. If you
still have a problem, get support at www.philips.
com/support.
Main unit
The buttons on the home theater do not work.
• Disconnect the home theater from the
power supply for a few minutes, then
reconnect.
Picture
No picture.
• Make sure that the TV is switched to the
correct source for the home theater.
No picture on a TV connected through HDMI.
• Make sure that you use a High Speed HDMI
cable to connect the home theater and TV.
Some Standard HDMI cables do not display
properly for some images, 3D video, or Deep
Color.
• Make sure that the HDMI cable is not faulty. If
it is faulty, replace it with a new cable.
• Press (Home) and then 731 on the
remote control to restore the default picture
resolution.
• Change the HDMI video setting, or wait for
10 seconds for auto recovery (see 'Picture
and video settings' on page 18).
Disc does not play high-definition video.
• Make sure that the disc contains highdefinition video.
• Make sure that the TV supports highdefinition video.
• Use an HDMI cable to connect to the TV.
EN
23
Sound
No sound from home theater speakers.
• Connect the audio cable from your home
theater to your TV or other devices. You do
not need a separate audio connection when
the home theater and TV are connected
through an HDMI ARC connection.
• Set up the audio for the connected device
(see 'Set up the audio' on page 10).
• Reset your home theater to its factory settings
(see 'Restore default settings' on page 19),
then switch it off and switch on again.
• On your home theater, press SOURCE
repeatedly to select the correct audio input.
Distorted sound or echo.
• If you play audio from the TV through the
home theater, make sure that the TV is muted.
Audio and video are not synchronized.
• 1) Press SOUND SETTINGS. 2) Press
the Navigation buttons (left/right) to select
AUD SYNC, and then press OK. 3) Press
the Navigation buttons (up/down) to
synchronize the audio with the video.
Play
Cannot play a disc.
• Clean the disc.
• Make sure that the home theater supports the
type of disc (see 'Media formats' on page 20).
• Make sure that the home theater supports
the region code of the disc.
• If the disc is a DVD±RW or DVD±R disc,
make sure that it is finalized.
Cannot play a DivX file.
• Make sure that the DivX file is encoded
according to the 'Home Theater Profile' with
the DivX encoder.
• Make sure that the DivX file is complete.
DivX or RMVB/RM subtitles do not display correctly.
• Make sure that the subtitle file name is the
same as the movie file name (see 'Subtitles'
on page 13).
• Select the correct character set: 1) Press
OPTIONS. 2) Select [Character set]. 3) Select
the supported character set. 4) Press OK.
Cannot read the contents of a USB storage device.
• Make sure that the format of the USB storage
device is compatible with the home theater.
• Make sure that the file system on the USB
storage device is supported by the home
theater.
24
EN
'No entry' or 'x' sign appears on the TV.
• The operation is not possible.
EasyLink does not work.
• Make sure that the home theater is
connected to a Philips brand EasyLink TV, and
the EasyLink option is turned on (see 'Set up
EasyLink (HDMI-CEC control)' on page 9).
When you switch on the TV, the home theater
automatically switches on.
• This behavior is normal when you are using
Philips EasyLink (HDMI-CEC). To make the
home theater work independently, switch off
EasyLink.
Cannot access BD-Live features.
• Make sure that the home theater is
connected a home network with internet
access (see 'Connect and set up a home
network' on page 10).
• Make sure that the network is set up. Use
a wired network installation (see 'Set up
the wired network' on page 10) or wireless
network installation (see 'Set up the wireless
network' on page 11).
• Make sure that the Blu-ray disc supports BDLive features.
• Clear memory storage (see 'BD-Live on Bluray' on page 12).
My 3D video played in 2D mode.
• Make sure that your home theater is
connected to a 3D TV through an HDMI cable.
• Make sure that the disc is a Blu-ray 3D disc,
and the Blu-ray 3D video option is on (see
'Play Blu-ray 3D disc' on page 12).
TV screen is black when you play a Blu-ray 3D
video or a DivX copy protected video.
• Make sure that the home theater is
connected to the TV through an HDMI cable.
• Switch to the correct HDMI source on the TV.
Network
Wireless network distorted or not found.
• Make sure that the wireless network is not
disturbed by microwave ovens, DECT phones,
or other neighboring Wi-Fi devices.
• Place the wireless router and the home
theater within five meters of each other.
• Use a USB extension cable to connect the
Wi-Fi dongle to the home theater.
• If the wireless network does not work
properly, try a wired network installation (see
'Set up the wireless network' on page 11).
Notice
This section contains the legal and trademark notices.
Copyright
This item incorporates copy protection technology
that is protected by U.S. patents and other
intellectual property rights of Rovi Corporation.
Reverse engineering and disassembly are
prohibited.
Compliance
This product incorporates proprietary technology
under license from Verance Corporation and is
protected by U.S. Patent 7,369,677 and other
U.S. and worldwide patents issued and pending
as well as copyright and trade secret protection
for certain aspects of such technology. Cinavia is
a trademark of Verance Corporation. Copyright
2004-2010 Verance Corporation. All rights
reserved by Verance. Reverse engineering or
disassembly is prohibited.
Cinavia notice
This product uses Cinavia technology to limit the
use of unauthorized copies of some commerciallyproduced film and videos and their soundtracks.
When a prohibited use of an unauthorized copy is
detected, a message will be displayed and playback
or copying will be interrupted.
More information about Cinavia technology
is provided at the Cinavia Online Consumer
Information Center at http://www.cinavia.com. To
request additional information about Cinavia by
mail, send a postcard with your mailing address to:
Cinavia Consumer Information Center, P.O. Box
86851, San Diego, CA, 92138, USA.
Open source software
Philips Electronics Singapore Pte Ltd hereby offers
to deliver, upon request, a copy of the complete
corresponding source code for the copyrighted
open source software packages used in this
product for which such offer is requested by the
respective licenses. This offer is valid up to three
years after product purchase to anyone in receipt
of this information. To obtain source code, please
contact open.source@philips.com. If you prefer not
to use email or if you do not receive confirmation
receipt within a week after mailing to this email
address, please write to "Open Source Team,
Philips Intellectual Property & Standards, P.O. Box
220, 5600 AE Eindhoven, The Netherlands". If you
do not receive timely confirmation of your letter,
please email to the email address above. The texts
of the licenses and acknowledgements for open
source software used in this product are included
on a separate leaflet.
RMVB end user agreement
(Asia Pacific and China only)
Notes to End User:
By using this product with RealNetworks software
and services, the end user agrees to the following
terms of REALNETWORKS, INC:
• End User may only use the software for
private, non-commercial use in accordance
with the terms of RealNetworks EULA .
• End User is not allowed to modify, translate,
reverse engineer, decompile, dissemble or
use other means to discover the source
code or otherwise replicate the functionality
of the Real Format Client Code, except to
the extent that this restriction is expressly
prohibited by applicable law.
• RealNetworks Inc. disclaims all warranties
and conditions other than those set forth in
this Agreement which are in lieu of all other
warranties, whether express and implied,
including but not limited to any implied
warranties or conditions of merchantability
and fitness for a particular purpose; and
effectively exclude all liability for indirect,
special, incidental and consequential damages,
such as but not limited to lost profits.
EN
25
English
9
Trademarks
"Blu-ray 3D" and "Blu-ray 3D" logo are trademarks
of Blu-ray Disc Association.
BONUSVIEW™
'BD LIVE' and 'BONUSVIEW' are trademarks of
Blu-ray Disc Association.
Java and all other Java trademarks and logos are
trademarks or registered trademarks of Sun
Microsystems, Inc. in the United States and/or
other countries.
Manufactured under license under U.S. Patent
Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535;
7,392,195; 7,272,567; 7,333,929; 7,212,872 & other
U.S. and worldwide patents issued & pending.
DTS-HD, the Symbol, & DTS-HD and the Symbol
together are registered trademarks & DTS-HD
Master Audio | Essential is a trademark of DTS, Inc.
Product includes software. DTS, Inc. All Rights
Reserved.
DivX , DivX Certified , DivX Plus HD
and associated logos are trademarks of Rovi
Corporation or its subsidiaries and are used under
license.
ABOUT DIVX VIDEO: DivX is a digital video
format created by DivX, LLC, a subsidiary of Rovi
Corporation. This is an official DivX Certified
device that plays DivX video. Visit divx.com for
more information and software tools to convert
your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified device must be registered in order to
play purchased DivX Video-on-Demand (VOD)
movies. To obtain your registration code, locate the
DivX VOD section in your device setup menu. Go
to vod.divx.com for more information on how to
complete your registration.
HDMI, the HDMI logo, and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC in the United
States and other countries.
DLNA , the DLNA Logo and DLNA CERTIFIED
are trademarks, service marks, or certification
marks of the Digital Living Network Alliance.
Real RMVB logo is a trademark or a registered
trademark of RealNetworks, Inc.
1
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
26
EN
2
2nd audio language
2nd subtitle language
3
3D disc in 2D mode
3D safety
3D video
C
12
12
12
3
12
change password
character set
clear BD-Live memory
connect to TV
connectors
control buttons (disc)
control buttons (USB)
copyright protection
customer support
18
13
12
7
4
12
12
25
3
D
5
5.1 speakers
A
advanced settings
amplifier
audio connection (analog cable)
audio connection (coaxial cable)
audio connection (HDMI ARC)
audio connection (optical cable)
audio formats
audio from other devices
audio input mapping
audio language
audio options
audio post processing
audio settings
audio setup
auto standby
auto subtitle shift
B
batteries
BD-Live
Blu-ray
Bonus View
brightness
browse PC
6
19
22
8
8
7
8
20
8
10
17
14
19
18
10
18
18
23
12
11
12
18
15
data files
deep color
default settings
disc language
disc menu
display panel
disposal
DivX
DLNA
13
18
19
17
17
18
3
13
15
E
Easylink (HDMI-CEC)
eject disc
enhanced audio
environment
9
4
19
3
F
factory settings
FAQs
file formats
19
3
20
H
HDMI ARC
HDMI audio
HDMI-CEC
home menu
home network
7
18
9
11
10
I
internet
10
EN
27
English
10 Index
K
karaoke
karaoke
M
main unit
manual setup
media formats
menu language
MP3
musical slideshows
N
network
night mode
O
one-touch play
one-touch standby
options
16
16
4
9
20
17
15
15
10
18
9
9
14
S
shuffle
sleep timer
slide animation
software update
software version
sound
speaker position
speaker setup
speaker specifications
subtitle language
subtitle position
surround sound
synchronize picture and sound
system audio control
T
troubleshooting (network)
troubleshooting (picture)
troubleshooting (play)
troubleshooting (sound)
tune radio stations
U
P
parental control
PBC (play back control)
picture options
picture resolution
picture settings
picture-in-picture
play disc
play from PC
play music
play radio
play USB storage device
power settings
predefined sound mode
preference
program radio stations
V
VCD
video connection (composite video)
video connection (HDMI ARC)
video connection (standard HDMI)
video formats
video options
video settings
VOD code (DivX)
W
R
radio
recycling
region codes
remote control
repeat
28
18
18
14
18
18
12
11
15
15
15
13
18
16
17
15
update software (through Internet)
update software (through USB)
USB storage device
user manual
EN
15
3
20
5
14
watch 3D
wired network
wireless network
14
18
14
19
19
16
6
9
20
17
18
17
12
10
24
23
24
24
15
20
19
13
3
18
8
7
7
22
14
18
13
12
10
11
Language Code
book1 indd
M
ac
© 2012 Koninklijke Philips Electronics N.V.
All rights reserved.
sgpjp_1208/93_v2
boo