Philips Fidelio A3 wireless Hi-Fi speaker AW3000

Register your product and get support at
www.philips.com/welcome
User manual
Contents
1 Important
2
Safety
Notice
2
3
2 Your Wireless Hi-Fi Speaker
Introduction
What's in the box
What else you need
Overview of the main unit
3 Prepare
Connect power and switch on
4 Connect AW3000 to your home
Wi-Fi network
Option 1: Set up wired connection
Option 2: Set up wireless connection
5 Play
Stream audio to AW3000
Listen to Internet radio stations
through AW3000
Play from an external device
6 Product information
4
4
4
4
4
6
6
7
7
8
10
10
11
12
6SHFLÀFDWLRQV
14
7 Troubleshooting
15
EN
1
1 Important
i Do not expose the product to dripping /
splashing water, rain or high humidity.
Notice
j Keep this product away from direct
VXQOLJKWQDNHGÁDPHVRUKHDW
Safety
Information for Europe:
Know these safety symbols
k Do not install near any heat sources
such as radiators, heat registers, stoves,
or other electrical equipment (including
DPSOLÀHUV
This product complies with the radio
interference requirements of the European
Community.
l Do not place any other electrical
equipment on the product.
m Do not place any sources of danger
on the product (e.g. objects containing
OLTXLGVEXUQLQJFDQGOHV
n Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
The 'exclamation mark' calls attention to
features for which you should carefully read the
supplied literature to prevent operating and
maintenance problems.
The 'lightening bolt' symbol indicates
uninsulated components within the product
that can cause an electric shock.
7RUHGXFHWKHULVNRIÀUHRUHOHFWULFVKRFNGR
not expose the product to rain or moisture and
GRQRWSODFHDQ\REMHFWVÀOOHGZLWKOLTXLGVVXFK
as vases, on the product.
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this product near water.
f Clean only with dry cloth.
g Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
h Do not remove the casing of this product.
2
EN
Warning
‡ Never remove the casing of this apparatus.
‡ Never lubricate any part of this apparatus.
‡ Never place this apparatus on other electrical
equipment.
‡ Keep this apparatus away from direct sunlight, naked
ÁDPHVRUKHDW
The device can be operated in the EU without
restrictions indoor, but cannot be operated
outdoors in France in the whole of the band
until further notice.
This product complies with the requirement of
the 1999/5/EC directive.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
DVSHFLDOL]HGFRPSDQ\3OHDVHREVHUYHWKH
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
Android is a trademark of Google Inc. Use of
this trademark is subject to Google permissions.
Class II equipment symbol:
0RGLÀFDWLRQV
0RGLÀFDWLRQVQRWDXWKRUL]HGE\WKH
manufacturer may void user's authority to
operate this product.
CLASS II apparatus with double insulation, and
no protective earth provided.
‡ Ensure that you always have easy access to the power
cord, plug or adaptor to disconnect this apparatus from
the power.
Risk of overheating! Never install this apparatus
LQDFRQÀQHGVSDFH$OZD\VOHDYHDVSDFHRI
at least four inches around this apparatus for
ventilation. Ensure curtains or other objects
never cover the ventilation slots on this
apparatus.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment and
human health.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Note
‡ The type plate is located on the bottom of the
apparatus.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
EN
3
2 Your Wireless
Hi-Fi Speaker
a +/‡ Adjust volume.
What else you need
Congratulations on your purchase, and
ZHOFRPHWR3KLOLSV7RIXOO\EHQHÀWIURPWKH
support that Philips offers, register your product
at www.philips.com/welcome.
If you contact Philips, you will be asked for the
model and serial number of this apparatus. The
model number and serial number are on the
bottom of the apparatus. Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
To stream audio wirelessly to AW3000, you
need:
‡ DFHUWLÀHG:L)LURXWHU
‡ an iOS or Android device, such as an
iPod touch/iPhone/iPad or an Android
phone or tablet; or a PC/Mac enabled
with Wi-Fi
‡ the Philips AirStudio app available on
Apple App Store (for iOS devices)
or Google Play Store (for Android
devices)
Your AW3000 should be connected to the
same local network as your iOS/Android device
or PC/Mac through the Wi-Fi router.
Introduction
Overview of the main unit
With this wireless Hi-Fi speaker, you can:
‡ stream audio from your iOS or
Android device.
‡ listen to Internet radio stations.
‡ stream audio from a PC/Mac installed
with Media Manager downloaded from
www.philips.com/mediamanager.
‡ play music from other audio devices
through the MP3-LINK socket.
c Power indicator/button
‡ Show the current status of the unit.
‡ Press to turn the unit on/off.
d DC IN
‡ Connect the power adaptor.
e ETHERNET
‡ (Optional) Connect to a wireless
router through an Ethernet cable (not
supplied).
f MP3-LINK
‡ Connect an external audio player
through the supplied MP3 link cable.
g WI-FI SETUP button
‡ Connect the unit to a Wi-Fi network.
h Screw hole for wall mounting
a
Tip
‡ Through the 1/4" (6.35mm) hole (depth: 9mm) on
b
What's in the box
Check and identify the contents of your
package:
‡ Wireless Hi-Fi speaker with built-in
Wi-Fi
‡ 1 x AC power adaptor
‡ 1 x MP3 link cable
‡ Quick start guide
‡ Safety sheet and other documents
b 1XPHULFNH\VWR
‡ Select an Internet radio station.
‡
the back of AW3000, you can mount the device
onto wall close to an AC outlet. Before the wall
mounting operation, you need to prepare the
following accessories (note supplied): (1) A suitable
wall mounting bracket; (2) A screw nut with the
VSHFLÀFDWLRQVRI··8160[SPP
(3) A screw (length: at least 15mm) that matches the
VSHFLÀHGVFUHZQXW
To facilitate cabling, leave a distance of more than
35mm between the wall mounting bracket and the
back of AW3000.
c
h
g
f
e
d
4
EN
EN
5
3 Prepare
Always follow the instructions in this chapter in
sequence.
Connect power and switch
on
Caution
‡ Risk of product damage! Make sure that the power
‡
‡
supply voltage matches the voltage printed on the
bottom of the unit.
Risk of electric shock! When you unplug the AC
adaptor, always pull the plug from the socket. Never
pull the cord.
Before you connect the AC adaptor, make sure that you
have completed all the other connections.
‡
To switch the unit on from standby mode,
press the power button/indicator above
again.
4 Connect
AW3000 to
your home WiFi network
There are two options for you to set up
connection between AW3000 and your existing
home Wi-Fi network.
‡ Wired connection
Use an Ethernet cable (not supplied) to
connect AW3000 to your home Wi-Fi router
directly. After successful connection, you can
enjoy wireless streaming to AW3000 through
your home Wi-Fi network.
Before connection of AW3000 to you home
Wi-Fi network, make sure that:
a your Wi-Fi router is powered on and
working properly.
b AW3000 is powered on and the
power indicator stays amber steadily.
Option 1: Set up wired
connection
12V=1A
DC
‡
IN
Connect the AC power cord to
‡ the DC IN socket on the back of the
unit.
‡ the wall power socket.
» The unit switches on automatically.
» The power indicator blinks amber, and
after a while turns to solid amber.
‡
To switch the unit to standby mode, press
the power button/indicator above .
6
EN
To Modem
LAN4
LAN3
LAN2
LAN1
Reset
‡ Wireless connection
Apply your home Wi-Fi settings to AW3000
from an iOS or Android device. Once
connected successfully, AW3000 will remember
your home Wi-Fi settings. Then you can enjoy
wireless streaming whenever AW3000 is
powered on and connected to your home WiFi network automatically.
‡
Connect an Ethernet cable (not supplied)
to:
‡ the ETHERNET socket on the back of
the unit
‡ one of the Ethernet ports on your
home Wi-Fi router
EN
7
Option 2: Set up wireless
connection
1
(For iPod touch/iPhone/iPad users) Install
Philips AirStudio from Apple App Store
and run the app.
3
Tap Setup a new speaker, read the general
setup steps, then tap Next to continue.
4
Check the power-on status of your
AW3000 as instructed, then tap Next to
continue.
5
Follow the on-screen instructions until
successful setup of Wi-Fi connection
between AW3000 and your home Wi-Fi
network.
‡ (For users of Android smartphones or
tablets) Install Philips AirStudio from
Android Market and run the app.
2
Find the activation code at the bottom of
your AW3000, then type in the box.
8
EN
EN
9
5 Play
Stream from your PC/Mac
To stream music from your PC/Mac to
AW3000, you need to install a media sharing
software (such as Media Manager available on
www.philips.com/mediamanager) to your PC/
0DFÀUVW,QWKLVZD\\RXU3&0DFFDQZRUNDV
a media sharing server that streams music to
compliant players.
Stream audio to AW3000
Note
‡ Make sure that your iOS/Android device or PC/Mac is
connected to the same Wi-Fi network as AW3000.
Stream from your iOS or Android
smartphone or tablet
1
Run Philips AirStudio on your iOS or
Android smartphone or tablet.
2
Hold and drag the icon of your device
towards the speaker to set up Wi-Fi
connection.
3
Tap the icon of your device to show music
available for streaming.
10
EN
4
1
Download Media Manager from www.
philips.com/mediamanager.
2
Install Media Manager onto your PC/Mac
with the license key available on the quick
start guide.
3
Run Philips AirStudio on your iOS or
Android smartphone or tablet.
4
Hold and drag the icon of your PC/
Mac towards the speaker to set up Wi-Fi
connection.
Select a song from the list to start play.
5
Tap the icon of your PC/Mac to show
music available for streaming.
6
Select a song from the list to start play.
Tip
‡ You can also control music play from the media sharing
software on your PC/Mac.
Listen to Internet radio
stations through AW3000
1
Run Philips AirStudio on your iOS or
Android smartphone or tablet.
2
Tap Services -> Philips AW3000.
3
Tap Internet radio to select the Internet
radio source.
EN
11
1
Connect the supplied MP3 link cable to:
‡ the MP3-LINK socket on the back of
the unit.
‡ the headphone socket on an external
audio player.
4
Tap MP3 link to select the MP3 link source.
5
Use the controls on your audio player to
control music play.
MP3 LINK
4
Follow the on-screen instructions to tune
to your favorite radio stations.
2
Run Philips AirStudio on your iOS or
Android smartphone or tablet.
3
Tap Services -> Philips AW3000.
Tip
‡ You can add your favorite stations to the preset list
as instructed on the app. Then, you can press the
QXPHULFNH\V on AW3000 directly to tune to the
corresponding radio station.
Play from an external device
You can also listen to an external audio player
through the unit.
12
EN
EN
13
6 Product
information
Note
‡ Product information is subject to change without prior
notice.
6SHFLÀFDWLRQV
$PSOLÀHU
Rated Output Power
Frequency Response
Signal to Noise Ratio
MP3 Link
2 X 18 W RMS
+]N+]“
dB
> 86 dB
800 mV RMS 20
kohm
Speakers
Speaker Impedance
Speaker Driver
Sensitivity
8 ohm
66 mm full range
82 dB/m/W
Wireless
Wireless
standard
Wireless
security
Frequency
range
PBC (one
button push)
14
EN
802.11b/g
WEP (64 or 128 bit),
WPA/WPA2 (8-63 characters)
0+]&+&+
(for /79, /37, /55, /97)
0+]&+&+
(for /12, /10, /05)
Yes
7 Troubleshooting
General information
AC power
PHILIPS
SWITCHING POWER
SUPPLY MODEL:
EFS05001800250 CE
Operation Power
Consumption
Power Consumption in
Standby Mode
Dimensions
- Main Unit (L x W x H)
Weight
- With Packing
- Main Unit
Input: 100 ~
240 V, 50/60
+]$
Output: 18 V
2.5 A
40 W
< 0.5 W
358 x 137 x
203 mm
3.05 kg
2.1 kg
Warning
‡ Never remove the casing of this apparatus.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
apparatus, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips web site (www.
philips.com/welcome). When you contact
Philips, ensure that the apparatus is nearby
and the model number and serial number are
available.
No power
‡
Make sure that the AC power plug of the
device is connected properly.
‡
Make sure that there is power at the AC
outlet.
No sound or poor sound
‡
Adjust volume on the Philips AirStudio app
or on AW3000 directly.
‡
If you have chosen the wired connection,
check whether the Ethernet cable has
been connected properly and securely
(see 'Option 1: Set up wired connection'
on page 7).
‡
Check the Wi-Fi network connection.
Set up the network again if needed (see
'Option 2: Set up wireless connection' on
page 8).
‡
If the audio source is an external audio
player, adjust volume on the audio player
directly.
No response from the unit
‡
Restart AW3000, and then set up the WiFi network for AW3000 again (see 'Option
2: Set up wireless connection' on page 8).
‡
Disconnect and reconnect the AC power
plug, and then switch on the device again.
Wi-Fi network connection failed
‡
Check if your Wi-Fi router is Wi-Fi
EJFHUWLÀHG7KLVGHYLFHLVRQO\
FRPSDWLEOHZLWK:L)LEJFHUWLÀHG
routers.
‡
If your Wi-Fi router is Wi-Fi 802.11n
FHUWLÀHGPDNHVXUHWRHQDEOHWKH
802.11b/g mode. AW3000 does not
support connection to routers with
802.11n only.
‡
This device does not support the WPSPIN method.
‡
Enable SSID broadcast on the Wi-Fi router.
‡
Keep away from potential sources of
interference which may affect Wi-Fi signal,
such as microwave ovens.
‡
Make sure that the SSID name of your
home router consists of alphanumeric
characters, with no space or special
characters like %/#/* inserted.
‡
If you choose to rename your AW3000
manually on the Philips AirStudio app, do
not use special characters or symbols.
‡
For some new types of Wi-Fi routers, a
network name (SSID) may be created
automatically when you use WPS for
connection. Always change the default
network name (SSID) to a simple one that
consists of alphanumerical characters, and
also change the Wi-Fi security mode to
secure your network.
Occasional breaking of music streaming
Do one or all of the following:
‡
Move AW3000 closer to your Wi-Fi router.
‡
Remove any obstacles between AW3000
and your Wi-Fi router.
‡
Avoid using Wi-Fi channel which is
overlapped by the nearby Wi-Fi network.
‡
Check if your network speed is fast enough
(in cases where multiple devices share the
same router, the wireless performance may
be affected). Turn off the other devices
connected to your home router.
‡
Enable the Quality of Service (QoS)
option (if available on the Wi-Fi router).
‡
Turn off other Wi-Fi routers.
EN
15
Music streaming failed with PC/Mac
‡
7HPSRUDULO\GLVDEOHWKHÀUHZDOODQG
security software to see whether it blocks
the ports that the media sharing software
(Media Manager) uses to stream content.
See the help documentation of your
ÀUHZDOODQGVHFXULW\VRIWZDUHRQKRZWR
unblock the ports used by wireless media
sharing.
‡
When you use iPod Touch/iPhone/iPad/PC/
Mac for music streaming, if the music play
breaks or stops, try to restart your iPod
Touch/iPhone/iPad, media sharing software,
or AW3000.
‡
Video streaming or FTP downloads may
overload your router and therefore may
cause interruptions during music streaming.
Try to reduce the load of your router.
16
EN
Specifications are subject to change without notice
© 2012 Koninklijke Philips Electronics N.V.
All rights reserved.
Document order number: 000000000000