OPERATION MANUAL
MODE D'EMPLOI
Sharp Plaza, Mahwah, New Jersey 07495-1163
SHARP CORPORATION
ENGLISH
FRANÇAIS
ESPAÑOL
LC-40LE830U/LC-46LE830U/LC-52LE830U/LC-60LE830U
SHARP ELECTRONICS CORPORATION
LC-40LE830U
LC-46LE830U
LC-52LE830U
LC-60LE830U
LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR ACL
TELEVISOR CON PANTALLA
DE CRISTAL LÍQUIDO
OPERATION MANUAL
MODE D'EMPLOI
MANUAL DE OPERACIÓN
MANUAL DE OPERACIÓN
Printed in Mexico
Imprimé au Mexique
Impreso en México
TINS-F030WJZZ
11P02-MX-NM
IMPORTANT : Please read this operation manual before starting operating the equipment.
IMPORTANT : Veuillez lire ce mode d'emploi avant de commencer à utiliser l'appareil.
IMPORTANTE : Lea este manual de operación antes de comenzar a operar el equipo.
LC-40_46_52_60LE830U_E_Cover.ind1 1
2011/01/26 22:12:04
Dimensional Drawings
1 3/64 (26.4)*2
LC-52LE830U
1 5/8 (41)*4
11 35/64
(293)
19 31/32 (507)
11 47/64
(298)
20°
15 3/4 (400)
3/4
15 3/4 (400)
(19)
7 3/32 (180)
15 3/4 (400)
4 19/64 (109)
17 11/64
(436)
45 23/64 (1152.0)*1
25 33/64*1
(648.0)
29 1/16 (738)
30 63/64 (787)
47 31/64 (1206)
Unit: inch (mm)
Unité: pouce (mm)
Unidad: pulgada (mm)
1 5/16 (33.4)*3
5 11/64
(131)
3 63/64
(101)
8 15/32 (215)
12 9/32
(312)
AN-52AG4
1 3/64 (26.4)*2
LC-60LE830U
1 5/16 (33.4)*3
6 5/16
(160)
54 29/64 (1383)
1 5/8 (41)*4
14 27/64 (366)
21 7/64 (536)
*2
*3
*4
LC-40_46_52_60LE830U_E_Cover.ind2 2
15 3/32 (383)
17 31/64 (444)
15 3/4 (400)
8 15/32 (215)
*1
10°
9 1/16 (230)
2 1/16 (52)
15 3/4 (400)
5 23/32 (145)
19 9/64 (486)
29 7/16*1
(747.63)
33 1/32 (839)
34 31/32 (888)
52 11/32 (1329.12)*1
3 63/64
(101)
8 13/64
(208)
Active area/Área activa/Zone active
AN-52AG4
Thinnest part/Parte más delgada/Partie la plus mince
Excluding projecting parts/Excluyendo partes salientes/Sauf les parties saillantes
Including projecting parts/Incluyendo partes salientes/Parties saillantes incluses
2011/01/26 22:12:05
ENGLISH
LC-40LE830U
LC-46LE830U
LC-52LE830U
LC-60LE830U
LIQUID CRYSTAL TELEVISION
ENGLISH
OPERATION MANUAL
IMPORTANT:
To aid reporting in case of loss or theft, please record the
TV's model and serial numbers in the space provided. The
numbers are located at the rear of the TV.
Model No.:
Serial No.:
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION:
The lightning flash with arrow-head
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within a
triangle is intended to alert the user
to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the product.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly
approved by the manufacturer could void the user's authority to operate this equipment.
1
LC-40_46_52_60LE830U_E.indb 1
2011/01/06 17:22:21
IMPORTANT INFORMATION
CAUTION:
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded
cables and connectors for connections.
DECLARATION OF CONFORMITY:
SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-40LE830U/LC-46LE830U/LC-52LE830U/LC-60LE830U
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RESPONSIBLE PARTY:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
TEL: 1-800-BE-SHARP
For Business Customers: URL http://www.sharpusa.com
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Wireless Radio
For product available in the USA/Canada market, only channel 1–11 can be operated. Selection of other channels is not possible.
This device is going to be operated in 5.15–5.25GHz frequency range, it is restricted in indoor environment only.
Important: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation of the device. This device and its antenna(s) must not be colocated or
operation in conjunction with any other antenna or transmitter.
Wireless Radio
For product available in the USA/Canada market, only channel 1–11 can be operated. Selection of other channels is not possible.
The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure.
Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where
required by the technology.
Important: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator
& your body.
“Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National
Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as practical.”
This product qualifies for ENERGY STAR when "Home" is selected for "TV Location".
Setting "TV Location" to "Home" allows the TV to achieve an energy-saving status for household use.
2
LC-40_46_52_60LE830U_E_01.indd 2
2011/01/28 11:22:38
DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years
of trouble-free operation of your product, please read the Important Safety Instructions carefully before
using this product.
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage
if improperly handled. This product has been engineered and manufactured with the highest priority on safety.
However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please
observe the following instructions when installing, operating and cleaning the product. To ensure your safety
and prolong the service life of your Liquid Crystal Television, please read the following precautions carefully
before using the product.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Additional Safety Information
15) Power Sources—This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery power, or other sources, refer to the
operating instructions.
16) Overloading—Do not overload wall outlets, extension cords, or integral convenience receptacles as this
can result in a risk of fire or electric shock.
17) Object and Liquid Entry—Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
18) Damage Requiring Service—Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an improper adjustment
of other controls may result in damage and will often require extensive work by a qualified technician
to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this indicates a need for service.
19) Replacement Parts—When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
20) Safety Check—Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
21) Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product
according to the method recommended by the manufacturer.
3
LC-40_46_52_60LE830U_E.indb 3
2011/01/06 17:22:21
IMPORTANT SAFETY INSTRUCTIONS
• Outdoor Antenna Grounding — If an outside antenna is
connected to the television equipment, be sure the antenna
system is grounded so as to provide some protection against
voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC — NATIONAL ELECTRICAL CODE
• Water and Moisture — Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool; and the like.
• Stand — Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base
can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart,
stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product
on a wall, be sure to follow the manufacturer's instructions. Use only the mounting hardware recommended by the
manufacturer.
• Selecting the location — Select a place with no direct sunlight and good ventilation.
• Ventilation — The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents
and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place
the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not
designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper
ventilation is provided or the manufacturer's instructions are followed.
• The front panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with
impact. Be careful not to be injured by broken glass pieces in case the panel breaks.
• Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
• The Liquid Crystal panel is a very high technology product with 2,073,600 pixels, giving you fine picture details.
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green, red or yellow. Please note
that this does not affect the performance of your product.
• Lightning — For added protection for this television equipment during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to
the equipment due to lightning and power-line surges.
• Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
• To prevent fire, never place any type of candle or flames on the top or near the TV set.
• To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.
• Do not display a still picture for a long time, as this could cause an afterimage to remain.
• To prevent fire or shock hazard, do not expose this product to dripping or splashing.
No objects filled with liquids, such as vases, should be placed on the product.
• Do not insert foreign objects into the product. Inserting objects in the air vents or other openings may
result in fire or electric shock. Exercise special caution when using the product around children.
Precautions when transporting the TV
• When transporting the TV, never carry it by holding or otherwise putting pressure onto the display. Be sure to always
carry the TV by two people holding it with two hands — one hand on each side of the TV.
Caring for the cabinet
• Use a soft cloth (cotton, flannel, etc.) and gently wipe the surface of the cabinet.
• Using a chemical cloth (wet/dry sheet type cloth, etc.) may deform the components of the main unit cabinet or cause
cracking.
• Wiping with a hard cloth or using strong force may scratch the surface of the cabinet.
• If the cabinet is very dirty, wipe with a soft cloth (cotton, flannel, etc.) soaked in neutral detergent diluted with water and
thoroughly wrung out, and then wipe with a soft dry cloth.
• Avoid using benzene, thinner, and other solvents, as these may deform the cabinet and cause the paint to peel off.
• Do not apply insecticides or other volatile liquids.
Also, do not allow the cabinet to remain in contact with rubber or vinyl products for a long period of time. Plasticizers
inside the plastic may cause the cabinet to deform and cause the paint to peel off.
4
LC-40_46_52_60LE830U_E.indb 4
2011/01/06 17:22:21
IMPORTANT SAFETY INSTRUCTIONS
Caring for the front panel
• Turn off the main power and unplug the AC cord from the wall outlet before handling.
• Gently wipe the surface of the front panel with a soft cloth (cotton, flannel, etc.).
To protect the front panel, do not use a dirty cloth, liquid cleaners, or a chemical cloth (wet/dry
sheet type cloth, etc.). This may damage the surface of the front panel.
• Wiping with a hard cloth or using strong force may scratch the surface of the front panel.
• Use a soft damp cloth to gently wipe the front panel when it is really dirty.
(It may scratch the surface of the front panel when wiped strongly.)
• If the front panel is dusty, use an anti-static brush, which is commercially available, to clean it.
• To avoid scratching the frame or screen, please use a soft, lint free cloth for cleaning. Approved cleaning cloths are
available directly from Sharp in single (00Z-LCD-CLOTH) or triple (00Z-LCD-CLOTH-3) packs. Call 1-800-BE-SHARP for
ordering, or VISIT http://www.sharpusa.com/SharpDirect.
CHILD SAFETY:
It Makes A Difference How and Where You Use Your Flat Panel Display
Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind:
THE ISSUE
• The home theater entertainment experience is a growing trend and larger flat panel displays
are popular purchases. However, flat panel displays are not always supported on the proper
stands or installed according to the manufacturer’s recommendations.
• Flat panel displays that are inappropriately situated on dressers, bookcases, shelves, desks,
speakers, chests or carts may fall over and cause injury.
THIS MANUFACTURER CARES!
• The consumer electronics industry is committed to making home entertainment enjoyable
and safe.
TUNE INTO SAFETY
• One size does NOT fit all. Follow the manufacturer’s recommendations for the safe installation
and use of your flat panel display.
• Carefully read and understand all enclosed instructions for proper use of this product.
• Don’t allow children to climb on or play with furniture and television sets.
• Don’t place flat panel displays on furniture that can easily be used as steps, such as a chest
of drawers.
• Remember that children can become excited while watching a program, especially on a
“larger than life” flat panel display. Care should be taken to place or install the display where it
cannot be pushed, pulled over, or knocked down.
• Care should be taken to route all cords and cables connected to the flat panel display so that
they cannot be pulled or grabbed by curious children.
WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT YOUR FLAT PANEL DISPLAY, ALWAYS:
• Use a mount that has been recommended by the display manufacturer and/or listed by an independent laboratory (such
as UL, CSA, ETL).
• Follow all instructions supplied by the display and wall mount manufacturers.
• If you have any doubts about your ability to safely install your flat panel display, contact your retailer about professional
installation.
• Make sure that the wall where you are mounting the display is appropriate. Some wall mounts are not designed to be
mounted to walls with steel studs or old cinder block construction. If you are unsure, contact a professional installer.
• A minimum of two people are required for installation. Flat panel displays can be heavy.
Note: CEA is the preeminent trade association promoting growth in the $161 billion U.S.
consumer electronics industry. More than 2,200 companies enjoy the benefits of CEA
membership, including legislative advocacy, market research, technical training and
education, industry promotion and the fostering of business and strategic relationships.
5
LC-40_46_52_60LE830U_E.indb 5
2011/01/06 17:22:22
Contents
IMPORTANT INFORMATION . . . . . . . . . . . . . . . . . . . . . 1
DEAR SHARP CUSTOMER . . . . . . . . . . . . . . . . . . . . . . . 3
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . 3-5
QUICK REFERENCE
Attaching the Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
QUICK INSTALLATION TIPS . . . . . . . . . . . . . . . . . . . 9
Using the Remote Control Unit . . . . . . . . . . . . . . . . . 9
Enjoying Photo/Music/Video Playback
Connecting a USB Memory Device/
USB Hard Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Connecting a Home Network (DLNA) Server . . . 41
Select the Files to Play Back . . . . . . . . . . . . . . . . . . . 42
Playing Back Files
on a USB Memory Device . . . . . . . . . . . . . . . . . 43-47
Playing Back Files
on a Home Network (DLNA) Server . . . . . . . 48-49
Preparation
Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installing Batteries in the Remote Control Unit . . . 10
Other Viewing Options
Presetting Remote Control Function . . . . . . . . . . . 50
Operating the Connected Equipment . . . . . . . 50-51
Part Names
TV (Front) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
TV (Rear) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Remote Control Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using AQUOS LINK
Controlling HDMI Equipment
Using AQUOS LINK . . . . . . . . . . . . . . . . . . . . . . . 52-54
Link Operation Menu . . . . . . . . . . . . . . . . . . . . . . . 54-55
Introduction to Connections
Experiencing HD Images . . . . . . . . . . . . . . . . . . . . . . 13
Types of Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Displaying an External Equipment Image . . . . . . . 13
Using a PC
Displaying a PC Image on the Screen . . . . . . . . . . 56
Adjusting the PC Image . . . . . . . . . . . . . . . . . . . . . . . 57
Setting Audio Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
PC Compatibility Chart . . . . . . . . . . . . . . . . . . . . . . . . 57
Control of the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-59
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connecting to External Equipment
Connecting a Blu-ray Disc/DVD Player or
HD Cable/Satellite Set-top Box . . . . . . . . . . . 14-15
Connecting a VCR, Game Console,
Camcorder or Cable/Satellite Set-top Box . . . . 15
Connecting an Audio Amplifier . . . . . . . . . . . . . . . . . 16
Connecting an AV Amplifier . . . . . . . . . . . . . . . . . . . . 16
Connecting a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Watching TV
Turning On/Off the Power . . . . . . . . . . . . . . . . . . . . . 18
Initial Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-20
Direct Button Operation
Changing Channels . . . . . . . . . . . . . . . . . . . . . . .
Changing Volume . . . . . . . . . . . . . . . . . . . . . . . . . .
MUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FLASHBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FREEZE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AV MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
APPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POWER SAVING . . . . . . . . . . . . . . . . . . . . . . . . . . .
Closed Captions and
Digital Closed Captions . . . . . . . . . . . . . . . . . . .
VIEW MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
21
21
21
21
21
22
22
22
22
23
24
On-Screen Display Menu
On-Screen Display Menu Operation . . . . . . . . . . . 25
Menu Operation Buttons . . . . . . . . . . . . . . . . . . . . . . 25
Menu Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-28
Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Power Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-33
Initial Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-37
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-40
Using the Internet
Connecting to the Internet . . . . . . . . . . . . . . . . . . 60-61
Internet Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-63
Displaying Updated Information and
Support Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Entering Text (Software Keyboard) . . . . . . . . . . . . . 64
Using the Browser. . . . . . . . . . . . . . . . . . . . . . . . . . 65-68
Using Applications via the Internet . . . . . . . . . . . . . 69
Appendix
Removing the Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Setting the TV on the Wall . . . . . . . . . . . . . . . . . . . . . 72
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73-74
Troubleshooting - Error Message . . . . . . . . . . . . . . 74
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Specifications
TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76-77
Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Information on the Software License for
This Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79-80
Calling for Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Dimensional Drawings
• The dimensional drawings for the LCD TV set are shown
on the inside back cover.
• The illustrations and on-screen displays in this operation manual are for explanation purposes and may vary slightly from
the actual operations.
• The examples used throughout this manual are based on the LC-60LE830U model.
6
LC-40_46_52_60LE830U_E.indb 6
2011/01/06 17:22:22
Supplied Accessories
Make sure the following accessories are provided with the product.
Remote control unit
(g1)
Page 9
“AAA” size battery
(g2)
Page 10
■ Operation manual (g1)
Cable tie
(g1)
Page 9
LC-40LE830U
LC-46LE830U
LC-52LE830U
LC-60LE830U
Stand unit
(g1)
Page 7
Stand unit
(g1)
Page 8
Stand unit
(g1)
Page 8
■ Connection guide (g1)
• Always use the AC cord supplied with the TV.
• The illustrations above are for explanation purposes and may vary slightly from the actual accessories.
QUICK REFERENCE
Attaching the Stand
• Before attaching (or detaching) the stand, unplug the AC cord.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged.
CAUTION
• Attach the stand in the correct direction.
• Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
■ LC-40LE830U
1
Confirm that there are 7 screws (3 long screws, 3
middle screws and 1 short screw) supplied with the
stand unit.
2
Attach the supporting post for the stand unit onto
the base as shown below.
4
Insert and tighten the 3 screws into the 3 holes on
the rear of the stand unit.
Middle screws
• The supporting post attaches to the base at an offcentered location on the base. Be sure to attach the
supporting post in the direction indicated below and
attach the stand to the TV with the wider side of the
base facing forward.
2
Long screws
5 1 Insert the stand cover.
2 Insert the screw to secure the stand cover.
Short screw
Forward
1
2
1
3
Insert the stand into the openings on the rear of the
TV.
Soft cushion
• To detach the stand, perform the steps in reverse
order.
7
LC-40_46_52_60LE830U_E.indb 7
2011/01/06 17:22:22
QUICK REFERENCE
■ LC-46LE830U/LC-52LE830U
1
Confirm that there are 9 screws (4 long screws, 4
middle screws and 1 short screw) supplied with the
stand unit.
2
Attach the supporting post for the stand unit onto
the base as shown below.
4
Insert and tighten the 4 screws into the 4 holes on
the rear of the stand unit.
Middle screws
• The supporting post attaches to the base at an offcentered location on the base. Be sure to attach the
supporting post in the direction indicated below and
attach the stand to the TV with the wider side of the
base facing forward.
2
Long screws
5 1 Insert the stand cover.
2 Insert the screw to secure the stand cover.
Forward
1
Short screw
2
1
3
Insert the stand into the openings on the rear of the
TV.
Soft cushion
• To detach the stand, perform the steps in reverse
order.
■ LC-60LE830U
1
Confirm that there are 10 screws (4 long screws, 4
middle screws and 2 short screws) supplied with the
stand unit.
4
Insert and tighten the 4 screws into the 4 holes on
the rear of the stand unit.
Middle screws
2
Attach the supporting post for the stand unit onto
the base as shown below.
• The supporting post attaches to the base at an offcentered location on the base. Be sure to attach the
supporting post in the direction indicated below and
attach the stand to the TV with the wider side of the
base facing forward.
2
Long screws
5 1 Insert the stand cover.
2 Insert the 2 screws to secure the stand cover.
1
Short screws
Forward
3
Insert the stand into the openings on the rear of the
TV.
2
1
Soft cushion
• To detach the stand, perform the steps in reverse
order.
8
LC-40_46_52_60LE830U_E.indb 8
2011/01/06 17:22:22
QUICK REFERENCE
QUICK INSTALLATION TIPS
1
2
Using the Remote Control Unit
Attach your antenna to the back of the television.
(See page 10.)
Connect the AC plug for the television into the AC
outlet.
Use the remote control unit by pointing it towards the
remote control sensor on the TV. Objects between the
remote control unit and the remote control sensor may
prevent proper operation.
2
1
1
AC outlet
• Place the TV close to the AC outlet, and keep the power
plug within reach.
• TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
TOUCH UN-INSULATED PARTS OF ANY CABLES
WITH THE AC CORD CONNECTED.
3
Bundle the cords properly with the cable tie.
Remote control sensor
17´ (5 m)
30º
30º
30º
30º *
* The angle is 20º when the stand is attached to the LC40LE830U/LC-46LE830U/LC-52LE830U model.
■ Cautions regarding the remote control unit
4
When turning on the TV for the first time, press
POWER on the touch sensor panel on the front of
the TV.
POWER
5
Insert the batteries into the remote control unit. (See
page 10.)
• Do not expose the remote control unit to shock. In addition,
do not expose the remote control unit to liquids, and do not
place in an area with high humidity.
• Do not install or place the remote control unit under direct
sunlight. The heat may cause deformation of the remote
control unit.
• The remote control unit may not work properly if the remote
control sensor on the TV is under direct sunlight or strong
lighting. In such cases, change the angle of the lighting
or the TV, or operate the remote control unit closer to the
remote control sensor.
IMPORTANT:
IF THE UNIT DOES NOT POWER ON - UNPLUG THE
TELEVISION FROM THE OUTLET AND REPEAT THE
INSTALLATION STEPS.
IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT
US AT 1-800-BE-SHARP.
• Speakers cannot be detached from the TV.
• The TV can be rotated up to 20 degrees to right and left.
9
LC-40_46_52_60LE830U_E_01.indd 9
2011/01/07 11:54:18
Preparation
Antennas
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections
that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector,
plug it into the antenna terminal at the rear of the TV set. For connecting the antenna cable to the TV, use
commercially available cables.
Connecting Antenna Cable
• Connect the antenna cable to the TV using one of the methods in the illustration as shown (1, 2, 3 or 4).
1 Cable without a CATV
converter
Home Antenna
terminal (75-ohm)
Cable TV lead-In
Coaxial cable
2 VHF/UHF antenna
Home Antenna
terminal (75-ohm)
75-ohm coaxial cable (round)
Coaxial cable
3 Combination VHF/
UHF antenna
75-ohm coaxial cable (round)
or
300-ohm twin-lead cable (flat)
4 Separate VHF/UHF
antenna
VHF
ANTENNA
UHF
ANTENNA
300/75-ohm adapter
300-ohm
twin-lead cable
OUT
IN
300-ohm twin-lead cable
or
Combiner
75-ohm coaxial cable
To TV antenna
terminal
F-type connector
1. A 75-ohm system is generally a round cable with F-type connector
that can easily be attached to a terminal without tools.
2. A 300-ohm system is a flat “twin-lead” cable that can be attached
to a 75-ohm terminal through a 300/75-ohm adapter.
75-ohm coaxial cable (round)
300-ohm twin-lead cable (flat)
NOTICE
F-type connector should be finger-tightened only.
When connecting the RF cable to the TV set, do not tighten F-type
connector with tools.
If tools are used, it may cause damage to your TV set. (The breaking
of internal circuit, etc.)
F-type connector
75-ohm coaxial cable
Installing Batteries in the Remote Control Unit
If the remote control fails to operate TV functions, replace the batteries in the remote control unit.
2 Insert two “AAA” size batteries (supplied with
3 Close the battery cover.
1 Open the battery cover.
the product).
• Place the batteries
with their terminals
corresponding to the (e)
and (f) indications in the
battery compartment.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage
in old batteries.
• Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with skin can cause a
rash. If you find any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove batteries from it.
10
LC-40_46_52_60LE830U_E.indb 10
2011/01/06 17:22:22
Part Names
TV (Front)
Center Icon illumination
(See page 33.)
OPC sensor *1
Remote control sensor
VOLl/k
CHV/U
INPUT MENU POWER *2
*1 OPC: Optical Picture Control (See page 27.)
*2 See pages 18 and 25 for using the touch sensor panel.
TV (Rear)
*1
RS-232C terminal
PC IN terminal
VIDEO 2 terminals
VIDEO 1 terminals
COMPONENT
terminals
*1
AUDIO OUT terminal
*1
USB 1 terminal
HDMI 1 terminal
ARC: Audio Return Channel
(See pages 52 and 53.)
HDMI 2 terminal
USB 2
terminal
ETHERNET
terminal
Antenna/
Cable in
DIGITAL AUDIO
OUTPUT terminal
AUDIO IN terminal
(shared for PC IN
and HDMI 1) *2
HDMI 3 terminal
HDMI 4 terminal
*1 See pages 13 to 17 and 52 for external equipment connection.
*2 See page 57 for details on the Audio Select function.
11
LC-40_46_52_60LE830U_E_01.indd 11
2011/01/17 20:18:29
Part Names
Remote Control Unit
1
1
POWER: Switch the TV power on or enter standby. (See
page 18.)
2
TV, STB, DVD•VCR, AUDIO: Switches the remote
control for TV, STB, DVD, BD, VCR and AUDIO operation.
(See pages 50 to 51 for details.)
18
* To enter the code registration mode, you need to press
an appropriate button (STB, DVD•VCR or AUDIO) and
DISPLAY at the same time.
19
2
3
External equipment operational buttons: Operate the
external equipment.
3
4
OPTION: Display the Link Operation Menu screen. This
button will function only when AQUOS LINK is used. (See
pages 52 to 55 for details.)
5
SLEEP: Set the sleep timer. (See page 21.)
6
0–9: Set the channel. (See page 21.)
7
• (DOT): (See pages 21 and 50.)
8
CC: Display captions from a closed-caption source. (See
page 23.)
9
AV MODE: Select an audio or video setting. (See page 22.)
4
5
20
21
6
7
22
8
9
10
11
12
23
24
13
27
25
26
10 MUTE: Mute the sound. (See page 21.)
11 VOLk/l: Set the volume. (See page 21.)
12 MENU: Display the menu screen. (See page 25.)
13 AQUOS NET: Switches the display to the TVkWeb,
Web or TV screen. (See pages 62 to 68 for details.)
14 a/b/c/d, ENTER: Select a desired item on the screen.
15 EXIT: Turn off the menu screen.
16 FAVORITE CH: Set the favorite channels. (See page 35.)
17 A, B, C, D: Select 4 preset favorite channels in 4 different
categories. (See page 35.)
While watching, you can toggle the selected channels by
pressing A, B, C and D.
14
18 DISPLAY: Display the channel information.
15
16
17
28
29
19 POWER (SOURCE): Turns the power of the external
equipment on and off.
20 FREEZE: Set the still image. Press again to return to
normal screen. (See page 21.)
21 POWER SAVING: Select Power Saving settings. (See
page 22.)
22 ENT: Jumps to a channel after selecting with the 0–9
buttons.
23 FLASHBACK: Return to the previous channel or external
input mode. (See page 21.)
24 VIEW MODE: Select the screen size. (See pages 24 and
56.)
25 INPUT: Select a TV input source. (TV, HDMI1, HDMI2,
HDMI3, HDMI4, COMPONENT, VIDEO1, VIDEO2, PC IN,
Home Network (DLNA), USB) (See pages 13 and 22.)
• When using the remote control unit, point it at the TV.
26 CHr/s: Select the channel. (See page 21.)
27 APPS: Display the application window. (See page 22.)
28 RETURN: Return to the previous menu screen.
29 FAV APP 1, 2, 3: You can assign your favorite
applications to these buttons. (See page 35.)
12
LC-40_46_52_60LE830U_E.indb 12
2011/01/06 17:22:23
Introduction to Connections
Experiencing HD Images
An HDTV without an HD source is just an ordinary TV.
To enjoy HD images on the TV, you should get HD programming from the following:
• Over-the-air broadcasting via HD quality antenna
• HD cable/satellite subscription
• HD compatible external equipment
• For information on updating to HD programming, ask your cable/satellite service provider.
Types of Connection
Image quality differs depending on the terminal used. To enjoy clearer images, check the output terminals of your
external equipment and use its appropriate terminals for higher quality images.
For connecting the TV to external equipment, use commercially available cables.
• The illustrations of the terminals are for explanation purposes and may vary slightly from the actual products.
Image
Quality
Terminal on external
equipment
Terminal
on the TV
Cable
HD
Quality
HDMI-certified cable
Page 14
Ø 3.5 mm stereo minijack cable
AUDIO
Page 14
DVI OUT
DVI-HDMI conversion cable
Component video cable
Page 15
Audio cable
AV cable
Standard
Quality
Page 15
Displaying an External Equipment Image
To view external source images, select the input source by pressing INPUT on the remote control unit or on the TV.
Example
Input
AIR
INPUT
INPUT
TV
HDMI1
HDMI2
HDMI3
Menu
1 Press INPUT.
• The INPUT list screen displays.
2 Press a/b to select the input source.
• You can also select the input source by pressing
INPUT. Each time INPUT is pressed, the input source
toggles.
HDMI1
TV
HDMI2
HDMI3
HDMI4
• An image from the selected source automatically
displays.
• If the corresponding input is not plugged in, you
cannot change the input. Be sure to connect the
equipment beforehand.
13
LC-40_46_52_60LE830U_E.indb 13
2011/01/06 17:22:23
Connecting to External Equipment
You can connect many types of external equipment to your TV. To view external source images, select the input
source from INPUT on the remote control unit or on the TV. (See pages 13 and 22.)
For connecting the TV to external equipment, use commercially available cables.
CAUTION
• To protect equipment, always turn off the TV before connecting any external equipment.
• Please read the relevant operation manual (Blu-ray disc player, etc.) carefully before making connections.
Connecting a Blu-ray Disc/DVD Player or HD Cable/Satellite Set-top Box
■ When using HDMI cable (HDMI 1, 2, 3 or 4):
The HDMI (High Definition Multimedia Interface) terminal is an audio-video interface that enables a connection for audio and
video signals using a single cable. The HDMI terminal supports high-resolution video input.
• Blu-ray disc player
• DVD player
• HD cable/satellite set-top box
Back panel
vertical inputs
HDMI-certified cable
HDMI OUT
• To enjoy 1080p display capability, connect your external equipment using an HDMI-certified cable or a component cable and
set the equipment to 1080p output.
• Supported Audio format: Linear PCM, sampling rate 32/44.1/48kHz.
• When you connect external equipment using a DVI-HDMI conversion cable or when you connect ARC-compatible
equipment, use HDMI 1.
■ When using DVI-HDMI conversion cable (HDMI 1):
• Blu-ray disc player
• DVD player
• HD cable/satellite set-top box
Back panel
horizontal inputs
Ø 3.5 mm stereo minijack cable
Back panel
vertical inputs
DVI-HDMI conversion cable
AUDIO
DVI OUT
• When using a DVI-HDMI conversion cable, you should make an analog audio connection. In this case, in addition to
connecting a DVI-HDMI conversion cable to the HDMI 1 terminal, connect a Ø 3.5 mm stereo minijack cable to the AUDIO IN
terminal and set "Audio Select" to "HDMI+Analog". (See page 57.)
14
LC-40_46_52_60LE830U_E.indb 14
2011/01/06 17:22:23
Connecting to External Equipment
■ When using Component cable (COMPONENT):
• Blu-ray disc player
• DVD player
• HD cable/satellite set-top box
Back panel
surface inputs
AUDIO-L (White)
AUDIO-R (Red)
Audio cable
PR (Red)
Y (Green)
PB (Blue)
Component video cable
COMPONENT OUT
• To enjoy 1080p display capability, connect your external equipment using an HDMI-certified cable or a component cable and
set the equipment to 1080p output.
• See page 14 for connecting a Blu-ray disc player, DVD player or an HD cable/satellite set-top box to the HDMI terminal.
Connecting a VCR, Game Console, Camcorder or Cable/Satellite Set-top Box
■ When using Composite cable (VIDEO 1 or 2):
• Game console
• Camcorder
• VCR
• Cable/Satellite set-top box
AUDIO-R (Red)
AUDIO-L (White)
AV cable
VIDEO (Yellow)
Back panel
surface inputs
15
LC-40_46_52_60LE830U_E.indb 15
2011/01/06 17:22:23
Connecting to External Equipment
Connecting an Audio Amplifier
■ When using optical fiber cable:
It is possible to output audio through the DIGITAL AUDIO OUTPUT terminal. (See page 32 for details.) PCM audio
outputs from the terminal.
Optical fiber cable
OPTICAL
DIGITAL AUDIO INPUT
Back panel
horizontal inputs
• Depending on the connected equipment, audio will not output from the DIGITAL AUDIO OUTPUT terminal in HDMI
connection. In this case, set the audio formats of the connected equipment to PCM, 32/44.1/48 kHz.
• Optical digital audio will be output in 2-ch stereo when it is from the external equipment connected to the TV using an HDMI cable.
■ When using audio cable:
Back panel
vertical inputs
Audio cable
ANALOG AUDIO IN
• See page 32 for details on the Output Select function.
Connecting an AV Amplifier
Back panel
vertical inputs
HD Cable/Satellite set-top box
HDMI-certified cable
HDMI OUT
HDMI
IN
HDMI
OUT
• If the image is not in sync with the audio, check the settings of the connected surround system.
• Letting the TV output the audio to an AV amplifier:
- When you connect ARC-compatible equipment, use the HDMI 1 terminal.
- If the equipment to be connected is not compatible with the ARC, connect an optical fiber cable.
16
LC-40_46_52_60LE830U_E.indb 16
2011/01/06 17:22:23
Connecting to External Equipment
Connecting a PC
Refer to page 57 for a list of PC signals compatible with the TV.
■ When using HDMI cable (HDMI 1, 2, 3 or 4):
Back panel
vertical inputs
HDMI-certified cable
HDMI OUT
• Depending on the board, only video signals may be output. In this case, in addition to connecting an HDMI-certified cable
to the HDMI 1 terminal, connect a Ø 3.5 mm stereo minijack cable to the AUDIO IN terminal and set "Audio Select" to
"HDMI+Analog". (See page 57.)
• The HDMI terminals only support digital signal.
■ When using DVI-HDMI conversion cable (HDMI 1):
Back panel
horizontal inputs
Ø 3.5 mm stereo minijack cable
AUDIO
DVI OUT
Back panel
vertical inputs
DVI-HDMI conversion cable
• When using a DVI-HDMI conversion cable, you should make an analog audio connection. In this case, in addition to
connecting a DVI-HDMI conversion cable to the HDMI 1 terminal, connect a Ø 3.5 mm stereo minijack cable to the AUDIO IN
terminal and set "Audio Select" to "HDMI+Analog". (See page 57.)
■ When using analog RGB cable (PC IN):
Analog RGB cable
(D-sub 15-pin cable or VGA cable)
Back panel
surface inputs
Ø 3.5 mm stereo minijack cable
RGB
AUDIO
Back panel
horizontal inputs
• When using an analog RGB cable, input the audio signal to the AUDIO IN terminal of PC IN.
• When connecting a PC to the PC IN, set "Audio Select" to "Video+Audio". (See page 57.)
17
LC-40_46_52_60LE830U_E.indb 17
2011/01/06 17:22:23
Watching TV
Turning On/Off the Power
Initial Installation
When you turn on the TV for the first time, it will
automatically memorize the broadcasting channels
available in the region where you live. Perform the
following steps before you press POWER on the
remote control unit.
1. Insert the batteries into the remote control unit. (See page 10.)
2. Connect the antenna cable to the TV. (See page 10.)
3. Plug in the AC cord to the AC outlet. (See page 9.)
POWER
POWER (On/Standby)
Language (Language setting)
Select from among 3 languages: English, French and
Spanish.
1 Press a/b to select the desired language listed
on the screen, and then press ENTER.
Press POWER on the TV or on the remote control unit
to turn the power on.
Language
TV Location
English
Antenna & Cable/STB
Français
Air/Cable
Español
• The Initial Installation starts when the TV powers on for the
first time. If the TV has been turned on before, the Initial
Installation will not be invoked. For changing the settings of
the Initial Installation, perform "EZ setup" on the Initial Setup
menu on page 34.
TV Location
Press POWER on the TV or on the remote control unit
again to turn the power off.
Select "Home" or "Store" for the location where
you plan to install the TV. This product qualifies for
ENERGY STAR in Home mode default setting.
• The TV enters standby and the image on the screen
disappears.
• If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the AC outlet.
• Weak electric power is still consumed even when the TV is
turned off.
CH Search
Completed
2 Press c/d to select "Home" or "Store".
Press ENTER to enter the setting.
Select
Home
Store
Home: “Power Saving” is set to "Advanced", and AV
MODE is set to "STANDARD".
Store: “Power Saving” is set to "Off" and AV MODE is
set to "DYNAMIC (Fixed)". Picture Reset and Feature
Demo can be set.
Picture Reset: AV MODE will be set to "DYNAMIC (Fixed)"
regardless of whether Picture Reset is "On" or "Off". If you
select "On", AV MODE will be reset to "DYNAMIC (Fixed)" if
there is no operation for 30 minutes. When "Off" is selected,
AV MODE will be set to "DYNAMIC (Fixed)".
Feature Demo: When “On” is selected, after all the settings
are completed, the Feature Demo screen is displayed if there
is no operation for several minutes.
• ENERGY STAR qualification is based on AV MODE
"STANDARD".
18
LC-40_46_52_60LE830U_E.indb 18
2011/01/06 17:22:24
Watching TV
Antenna & Cable/STB
Select the type of connection you will use to
watch TV.
CH Search (Channel search)
3 Press c/d to select "Antenna & Cable" or "Set-
5 When "Air" is selected in Antenna setting:
top box", and then press ENTER.
Antenna & Cable
Channel auto search makes the TV look for all
channels viewable in the set area.
Press c/d to select "Start", and then press
ENTER.
Set-top box
Start
To watch TV via an antenna or cable
connection (without using a set-top box):
Select "Antenna & Cable", and then go to step 4.
To watch TV via a set-top box:
1 Select "Set-top box", and then press ENTER.
2 To watch TV, select the input source
corresponding to the terminal connected to the
set-top box. When doing so, you must make
the setting to skip "TV". Press c/d to select
"On", and then press ENTER.
Cancel
When "Cable" is selected in Antenna setting:
1 Press a/b to select "Analog & Digital Search
Start" to search both analog and digital
broadcasts, or to select “Analog Search Start”
to search only analog broadcasts, and then
press ENTER.
Analog & Digital Search Start
Analog Search Start
Cancel
On
Off
• When this is set to "On", the channel on the TV
cannot be changed using the remote control unit or
menu. (e.g. CH r/s, Favorite CH, etc.)
• See page 32 for details on the Input Skip function.
3 Press INPUT to select the input source
corresponding to the terminal connected to the
set-top box. Make the necessary settings on
the connected external equipment.
• The Channel search will start automatically.
• To exit the Channel search screen, select "Cancel",
and then press ENTER.
2 The Channel search results may include
scrambled channels or channels that are not
viewable in the set area. Press c/d to select
"Yes", and then press ENTER to remove
scrambled channels.
Yes
No
• See the operation manual of the connected
equipment for setting up the equipment.
Air/Cable (Antenna setting)
Make sure what kind of connection is made with your
TV when selecting "Air" or "Cable".
4 Press c/d to select "Air" or "Cable".
Press ENTER to enter the setting.
Air
Cable
19
LC-40_46_52_60LE830U_E.indb 19
2011/01/06 17:22:24
Watching TV
Completed
6 The settings confirmation screen is displayed.
Confirm the information displayed on the screen,
and then press ENTER.
Examples of the settings confirmation screen
When one or more channel is received after
"Antenna & Cable" was selected in step 3 and a
search was carried out.
Language
TV Location
Anntena & Cable/STB
Air/Cable
Search Result
: English
: Home
: Antenna & Cable
: Air
: Digital 4ch
Analog 7ch
Press the INPUT button,
then the right arrow d,
to see the list of channels found.
OK
When no channel is received after "Antenna &
Cable" was selected in step 3 and a search was
carried out.
Language
TV Location
Anntena & Cable/STB
Air/Cable
Search Result
: English
: Home
: Antenna & Cable
: Cable
: No channel
Channel not found.
Antenna/Cable are not properly connected
or Air/Cable setup is incorrect.
Please check your Antenna/Cable connection
and Air/Cable setup.
OK
When "Set-top box" was selected in step 3 and a
search was carried out.
Language
TV Location
Anntena & Cable/STB
TV Input Skip
: English
: Home
: Set-top box
: On
Please make sure to change INPUT to the
specific input terminal you are connecting
your set-top box to get the picture.
Closed caption, sub-channel audio
and channel selection need to be selected
with your set-top box.
OK
• If no channel is found, confirm the type of connection
made with your TV and try "EZ Setup" again.
(See page 34.)
• For changing the settings of the Initial Installation, perform
"EZ setup" on the Initial Setup menu on page 34.
• To see the list of channels found during Channel search,
press INPUT, and then press d.
20
LC-40_46_52_60LE830U_E.indb 20
2011/01/06 17:22:24
Direct Button Operation
MUTE
Mutes the current sound output.
Press MUTE.
• " " will be displayed on the screen for 30 minutes, and
the sound is silenced.
• Within 30 minutes of pressing MUTE, mute can be
canceled by pressing VOLk/l or MUTE.
• Mute will be canceled after 30 minutes have passed.
However, the TV will not suddenly output a loud sound as
the volume level is set to 0 automatically.
Sleep Timer
Changing Channels
You can change channels in several ways.
Method 1
Using CHr/s on the remote control unit or on the TV.
Method 2
Using remote control buttons 0-9, • (DOT).
Examples:
To select a 1 or 2-digit channel number (e. g., Channel 5):
Press 5
ENT.
To select a 3-digit channel number (e. g., Channel 115):
Press 1
1
5
ENT.
To select a 4-digit channel number (e. g., Channel 22.1):
Press 2
2
• (DOT)
1
ENT.
Method 3
Selecting the program from Channel list.
1 Press INPUT on the remote control unit.
• The INPUT list displays.
2 Press c/d to select "AIR" or "CABLE".
• The Channel list displays.
3 Press a/b to select the desired channel, and then
press ENTER.
• When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
• When you enter 0-9 only, channel selection will be made if
there is no operation within a few seconds.
• If you push "0" by itself, nothing will happen.
• Complete the above steps within a few seconds.
• When you enter 0-9 and • (DOT), channel selection will be
made if there is no operation within a few seconds.
Changing Volume
You can change the volume by pressing VOLk/l on
the TV or on the remote control unit.
• To increase the volume, press VOLk.
• To decrease the volume, press VOLl.
20
Audio status
Output device
Speaker
Allows you to set a time when the TV automatically
switches to standby.
Press SLEEP.
• The remaining time displays when the sleep timer has been set.
• Each time you press SLEEP, the remaining time switches
as shown below.
Off
30
60
90
120
• When set, the time automatically starts counting down.
• If you want to adjust the sleep timer, you can press SLEEP
twice then change the time setting.
• When it is 5 minutes before the time expires, the remaining
time will start to keep appearing every minute.
• Select "Off" by pressing SLEEP to cancel the sleep timer.
• The TV will enter standby when the remaining time reaches 0.
FLASHBACK
Press FLASHBACK to switch to the previously tuned
channel.
• Press FLASHBACK again to switch back to the currently
tuned channel.
• FLASHBACK will not work if no channel has been
changed after the TV is turned on.
FREEZE
Allows you to capture and freeze a moving image that
you are watching.
Press FREEZE.
• A moving image is captured.
• Press FREEZE again to cancel the function.
• When this function is not available, "No displaying still
image available." will display.
• The still image automatically goes out after 30 minutes.
• If you are using the freeze function and a broadcast
activates the V-CHIP BLOCK, the freeze function will be
canceled and a V-CHIP BLOCK message will appear.
• You can have the same settings by choosing "Freeze" on
the menu items. (See page 31.)
Output Select
Fixed
Variable
Variable sound
Mute
• When "Output Select" is set to "Variable", the indicator on
the screen changes as shown below.
60
• See page 32 for details on the Output Select function.
21
LC-40_46_52_60LE830U_E.indb 21
2011/01/06 17:22:24
Direct Button Operation
AV MODE
INPUT
AV MODE gives you several viewing options to choose
from to best match the surrounding environment of the
TV, which can vary due to factors like room brightness,
type of program watched or the type of image input
from external equipment.
Press AV MODE. Current AV MODE displays.
• Press AV MODE again before the mode displayed on the
screen disappears. The mode changes as shown below:
Example:
When the input source is TV, COMPONENT,
VIDEO 1 or 2
AUTO
STANDARD
DYNAMIC (Fixed)
MOVIE
DYNAMIC
STANDARD
USER [TV]
DYNAMIC (Fixed)
MOVIE
DYNAMIC
GAME
x.v.Color*
USER[
• The INPUT list screen displays.
2 Press a/b or press INPUT again to select the
input source.
• An image from the selected source automatically displays.
• Each time INPUT is pressed, the input source toggles.
• If the corresponding input is not plugged in, you cannot change
the input. Be sure to connect the equipment beforehand.
• See pages 13 to 17 and 52 for external equipment
connection.
GAME
APPS
Example:
When the input source is PC IN or HDMI 1 to 4
AUTO
To view external source images, select the input source by
pressing INPUT on the remote control unit or on the TV.
1 Press INPUT.
PC
]
* "x.v.Color" can only be selected when an x.v.Color
signal is input using HDMI 1 to 4.
AUTO: Optimizes the image quality automatically based
on the room brightness and image signal.
STANDARD: For a highly defined image in a normal
lighting.
MOVIE: For a movie.
GAME: Lowers image brightness for easier viewing.
PC: For PC.
USER: Allows the user to customize settings as desired.
You can set the mode for each input source.
x.v.Color: Supports the x.v.Color international standard
for wide color space. The x.v.Color signal allows you
to experience colors that conventional color signals
cannot reproduce.
DYNAMIC: For a clear-cut image emphasizing high
contrast, useful for sports viewing.
DYNAMIC (Fixed): Changes the image and sound
settings to the factory preset values. No adjustments
are allowed.
• You can select a different AV MODE item for each input
mode. (For example, select STANDARD for TV input and
DYNAMIC for COMPONENT.)
• When you play games, "GAME" is recommended for AV
MODE.
• You cannot set "GAME" or "PC" when the TV is connected
to the Internet or when the input source is "Home Network
(DLNA)" or "USB".
• You can have the same settings by choosing "AV MODE"
on the menu items. (See page 27.)
Allows you to directly activate various types of
applications.
1 Press APPS to display the application window.
2 Press a/b/c/d to select the desired application,
and then press ENTER.
" is displayed after you switch to USB mode, check
• If "
the USB connection.
" is displayed after you switch to Home Network
• If "
(DLNA) mode or after you connect to the Internet, check
your TV's network settings and connection.
• See pages 42, 62, 63 and 69 for details of viewable
applications.
• You can display the application window by choosing
"APPS" on the menu items. (See page 31.)
• When this function is not available, "Can not operate this
function now" will display.
POWER SAVING
Allows you to set the Power Saving level in order to
decrease the power consumption and increase the
backlight lifespan.
Press POWER SAVING.
• Each time you press POWER SAVING, the mode changes
as shown below.
Off
Standard
Advanced
• You can have the same settings by choosing "Power
Saving" on the menu items. (See page 30.)
22
LC-40_46_52_60LE830U_E.indb 22
2011/01/06 17:22:24
Direct Button Operation
Closed Captions and Digital Closed Captions
Your TV is equipped with an internal Closed Caption
decoder. It allows you to view conversations, narration
and sound effects as subtitles on your TV. Closed
Captions are available on some TV programs and on
some VHS home video tapes at the discretion of the
program provider.
1 Press CC.
Digital Closed Caption service is a new caption service
available only on digital TV programs (also at the
discretion of the service provider). It is a more flexible
system than the original Closed Caption system,
because it allows for a variety of caption sizes and font
styles. When the Digital Closed Caption service is in
use, it will be indicated by the appearance of a 3-letter
abbreviation that also indicates the language of the
Digital Closed Captions: ENG (English), SPA (Spanish),
FRA (French) or other language codes.
Air
Not all programs and VHS videotapes offer closed
captions. Please look for the “N” symbol to ensure
that captions will be shown.
In the Closed Caption system, there can be more than
one caption service provided. Each is identified by its
own number. The “CC1” and “CC2” services display
subtitles of TV programs superimposed over the
program's picture.
In the Closed Caption system, the “Text1” or “Text2”
services display text that is unrelated to the program
being viewed (e.g., weather or news). These services
are also superimposed over the program currently
being viewed.
• This will present the Closed Caption information display.
2 Press CC while the Closed Caption information is
still on the screen.
• Press repeatedly until you select the desired closed
caption service.
DIGITAL
Audio
Video
CC
Ratings
22.1
:
:
:
:
STEREO
480p (4:3)
1/2 CC1
NONE
Closed Caption
information
• Depending on the number of caption services in the
signal being received, you will see information such as
1/2 or 1/4 displayed.
1/2 means “the first of two services”.
Example:
If a program has three services (Digital CC(ENG), CC1
and Text1), the closed caption display will toggle in this
sequence:
1/3 ENG
2/3 CC1
3/3 Text1
Off
• The CC button keeps a record of the last service
selected in its memory.
If the last closed caption mode (e.g. 1/3 ENG) you
selected is not available for the next program, or on
another channel, the closed caption service that is
available is automatically selected, and this service
appears in parentheses, e.g. “1/3(CC1)”.
Closed Caption services that appear in parentheses will
not be stored in the CC button's memory as your last
selected service. Only services that you have selected
with the CC button are stored.
Examples:
In a case where there are two closed caption
services provided (for instance, Digital CC(ENG)
and CC1), and Digital CC(ENG) is displayed
as your current selection, if Digital CC(ENG) is
not broadcast for the next program, the other
closed caption service, CC1, will be displayed in
parentheses.
A closed caption service appears in parentheses
because the service you selected is not available
and a different service is displayed on your screen.
“1/1(CC1)” is displayed instead of “1/2/ENG”.
• When “Power Saving” is set to “Standard” or “Advanced”,
the Power Saving leaf icon appears on the channel
information window. See page 30 for details of Power
Saving settings.
• See page 33 for detailed closed caption settings.
• When the program contains no closed caption, “--”
displays in the closed caption information.
• If the language code, e.g. “ENG”, is not found on Digital TV
programs, “--” will be shown.
• Four kinds of closed caption service (CC1, CC2, Text1,
Text2) are potentially available, but a broadcast may
contain none or only some of these services at the
discretion of the program provider.
• When TV+Web or Web is displayed, Closed Captions are
not available.
• You can have the same settings by choosing "Change CC"
on the menu items. (See page 32.)
23
LC-40_46_52_60LE830U_E.indb 23
2011/01/06 17:22:25
Direct Button Operation
VIEW MODE
You can select the screen size.
1 Press VIEW MODE.
• The View Mode menu displays.
• The menu lists the View Mode options selectable for the type of video signal currently
being received.
2 Press VIEW MODE or a/b while the View Mode menu is displayed to select a
desired item on the menu.
• You can sequentially select a View Mode that has its own aspect ratio.
• You can have the same settings by choosing "View Mode" on the menu items. (See page 31.)
■ For HD programs
Stretch
Suitable for viewing widescreen 1.78:1 aspect ratio
program, stretch mode will still
show very thin black bands
at the top and bottom of the
screen.
Dot by Dot (Full Screen)
S.Stretch (Smart stretch)
Dot by Dot (1080i/p only):
Suitable for stretching 4:3
Detects the resolution of the
programs to fill the screen.
signal and displays an image
with the same number of
pixels on the screen.
Full Screen (720p only): You
can select "Full Screen" only
when receiving a 720p signal.
Zoom
Suitable for viewing widescreen 2.35:1 aspect-ratio
programs in full screen.
• When using Dot by Dot or Full Screen, it is possible to see noise or bars around different outer portions of the screen. Please
change view mode to correct this.
■ For 4:3 programs
Example: Screen size images
Side Bar
Suitable for viewing
conventional 4:3 programs in
their normal format.
S.Stretch (Smart stretch)
Suitable for stretching 4:3
programs to fill the screen.
Zoom
Suitable for viewing widescreen 2.35:1 anamorphic
DVDs in full screen.
Stretch
This mode is useful for 1.78:1
DVDs. When viewing 1.85:1
DVDs, stretch mode will still show
very thin black bands at the top
and bottom of the screen.
■ For USB-Video, DLNA-Video or Internet applications
Example: Screen size images
Input signal
Auto
Keeps the original
aspect ratio in a full
screen display.
Original
Displays an image by
an original size.
24
LC-40_46_52_60LE830U_E.indb 24
2011/01/06 17:22:25
On-Screen Display Menu
On-Screen Display Menu Operation
LCFONT embedded
System
Options
: Select
Initial
Setup
ENTER
: Enter
RETURN
Picture
Settings
Information
: Back
MENU
: Exit
Example
Example
Menu
System
Options
: Select
Picture Settings
Initial
Setup
ENTER
: Enter
RETURN
: Back
MENU
: Exit
Menu
Picture
Settings
Information
Picture Settings
AV MODE (Changing Pic.Quality)
AV MODE (Changing Pic.Quality)
[STANDARD]
[STANDARD]
OPC
OPC
[On:Display]
Backlight
[ b5] a16
Contrast
[b30]
0
Brightness
[
0] a30
Color
[ b2] a30
Tint
[
0] a30
Sharpness
[ b2] a10
Backlight
[ b5] a16
b16
Contrast
[b30]
b40
0
Brightness
[
b30
0] a30
Color
[ b2] a30
b30
Tint
[
b30
0] a30
Sharpness
[ b2] a10
b10
Advanced
Advanced
Reset
Reset
b16
b40
b30
b30
b30
b10
1 Guide display
1 Press MENU to display the MENU screen.
2 1 Press c/d to select the desired menu.
2 Press a/b to select a specific adjustment item,
and then press ENTER.
• Additional related adjustment items may be
displayed. Press a/b to select the desired item.
3 Adjust the item while referring to the guide
display.
• Operations vary depending on the function or item.
Refer to the guide display corresponding to the
menu setting screen for button operations.
3 Press MENU to exit.
• This indicates the buttons that can be operated on the
displayed screen. The guide display varies depending
on the menu setting screen.
• The operations for some selected items may be displayed
in the operational guide bar at the bottom of the screen.
2 Item displayed in blue
• This indicates the item currently selected.
• Press ENTER to go to the adjustment screen for this item.
3 Item in brackets
• This indicates the current setting for the item.
4 Item displayed in white
• This indicates that the item can be selected.
5 Item displayed in gray
• This indicates that the item cannot be selected.
There are various reasons why the items cannot be
selected, but the main reasons are as follows:
—Nothing is connected to the selected input terminal.
—The function is not compatible with the current input signal.
• Menu options differ in the selected input modes, but the operating procedures are the same.
• The screens in the operation manual are for explanation purposes (some are enlarged, others cropped) and may vary slightly
from the actual screens.
• The order of explanations for each menu item in the following pages is not necessarily in accordance with the alignment of
the items on the screen.
LCFONT:
• This product is embedded with LC Font technology, which was developed by SHARP Corporation for clearly displaying easyto-read characters on LCD screens.
Menu Operation Buttons
Using the remote control
Use the following buttons on the remote control to
operate the menu.
MENU:
Press to open or close the menu screen.
a/b/c/d: Press to select a desired item on the screen or
adjust a selected item.
ENTER:
Press to go to the next step or complete the
setting.
RETURN: Press to return to the previous step.
Using the touch sensor panel of the main unit
You can also operate the menu with the touch sensor
panel of the main unit.
Button operations on the touch sensor panel correspond
to the ones on the remote control as shown below.
VOLl/k:
CHV/U:
INPUT:
MENU:
Cursor c/d on the remote control.
Cursor a/b on the remote control.
ENTER on the remote control.
MENU on the remote control.
25
LC-40_46_52_60LE830U_E_03.indd 25
2011/01/31 20:28:05
On-Screen Display Menu
Menu Items
• When AV MODE is set to "AUTO", part of the menu may not be displayed correctly or the setting range of the menu may be
changed.
• Some menu items may not be displayed depending on the selected input source.
Picture Settings
AV MODE (Changing Pic.Quality) ..... Page 27
OPC ................................................ Page 27
Backlight ......................................... Page 27
Contrast .......................................... Page 27
Brightness ....................................... Page 27
Color ............................................... Page 27
Tint.................................................. Page 27
Sharpness ....................................... Page 27
Advanced ................................. Pages 27-28
C.M.S.-Hue ........................... Page 27
C.M.S.-Saturation ................. Page 27
C.M.S.-Value......................... Page 27
Color Gamut Range .............. Page 28
Color Temp. ......................... Page 28
Motion Enhancement ............ Page 28
Quad Pixel Plus ..................... Page 28
Active Contrast ..................... Page 28
Gamma Adjustment .............. Page 28
Black Level............................ Page 28
Film Mode ............................. Page 28
Digital Noise Reduction ......... Page 28
Monochrome ........................ Page 28
Range of OPC ....................... Page 28
Reset .............................................. Page 27
Audio Settings
Auto Volume ................................... Page 29
Treble .............................................. Page 29
Bass................................................ Page 29
Balance ........................................... Page 29
Surround ......................................... Page 29
Bass Enhancer ................................ Page 29
Clear Voice ...................................... Page 29
Reset .............................................. Page 29
Power Control
Audio Only ...................................... Page 30
Power Saving .................................. Page 30
No Signal Off ................................... Page 30
No Operation Off ............................. Page 30
26
LC-40_46_52_60LE830U_E.indb 26
System Options
View Option.................. Pages 31-32, 46, 49
APPS .................................... Page 31
USB Operation Panel ............ Page 46
Home Network (DLNA)
Operation Panel .................... Page 49
View Mode ............................ Page 31
Freeze ................................... Page 31
Change Audio ....................... Page 31
Change CC ........................... Page 32
AQUOS LINK Setup ........................ Page 53
Input Terminal Setting...............Pages 32, 57
Audio Setup .......................... Page 32
PC input ................................ Page 57
Audio Select.......................... Page 57
Input Skip.............................. Page 32
Input Label ............................ Page 32
HDMI Setup .......................... Page 32
Output Select ........................ Page 32
Color System ........................ Page 32
Menu Design ............................ Pages 32-33
Channel Selecting Effect ....... Page 32
Program Title Display ............ Page 32
Position ................................. Page 32
Caption Setup ....................... Page 33
Game Play Time .............................. Page 33
Operation Lock Out ......................... Page 33
Icon Light Up Setting ....................... Page 33
Demo Mode .................................... Page 33
Initial Setup
EZ Setup ......................................... Page 34
Language .............................. Page 34
TV Location ........................... Page 34
Antenna & Cable/STB ........... Page 34
Air/Cable ............................... Page 34
CH Search ............................ Page 34
Completed ............................ Page 34
Broadcasting Setup.................. Pages 34-35
CH Setup .............................. Page 34
Favorite CH ........................... Page 35
Antenna Setup-DIGITAL ........ Page 35
Internet Setup .......................... Pages 62-63
Language ........................................ Page 35
DivX® Setup..................................... Page 47
Individual Setup ........................ Pages 35-37
Secret No. ............................ Page 35
Parental CTRL................ Pages 35-37
Wall Mount Audio Setup .................. Page 35
FAV APP Key Assign ....................... Page 35
Reset .............................................. Page 35
Information
Identification .................................... Page 38
Digital Caption Info. ........................ Page 38
Software Update ...................... Pages 38-40
Manual Update .............. Pages 38-40
Auto Update Setting.............. Page 38
Netflix Help ...................................... Page 69
Vudu Help ....................................... Page 69
2011/01/06 17:22:25
On-Screen Display Menu
AV MODE (Changing Pic.Quality)
Picture Settings
Adjusts the picture to your preference with the
following picture settings.
Example
Picture
Settings
The audio and video settings can be changed to suit
the program or input content being watched.
Select from the following AV modes.
■ When the input source is TV, COMPONENT,
VIDEO 1 or 2:
Menu
AUTO/STANDARD/MOVIE/GAME/USER/DYNAMIC/
DYNAMIC(Fixed)
Picture Settings
■ When the input source is PC IN or HDMI 1 to 4:
AUTO/STANDARD/MOVIE/GAME/PC/USER/x.v.Color/
DYNAMIC/DYNAMIC(Fixed)
AV MODE (Changing Pic.Quality)
[STANDARD]
OPC
[On:Display]
Backlight
[ b5] a16
Contrast
[b30]
0
Brightness
[ 0] a30
Color
[ b2] a30
Tint
[ 0] a30
Sharpness
[ b2] a10
• The selectable items vary depending on the input source.
• You can select AV MODE by pressing AV MODE on the
remote control unit. See page 22 for details of AV MODE
settings.
b16
b40
b30
b30
OPC Setting
Automatically adjusts the brightness of the screen.
b30
Off: The brightness is fixed at the value set in "Backlight".
On: Automatically adjusts.
On:Display: Displays the OPC effect on the screen while
adjusting the brightness of the screen.
b10
Advanced
Reset
1 Press MENU to display the MENU screen, and then
press c/d to select "Picture Settings".
2 Press a/b to select a specific adjustment item.
• Select "Advanced" and then press ENTER to set
"C.M.S.-Hue", "C.M.S.-Saturation", "C.M.S.-Value",
"Color Gamut Range", "Color Temp.", "Motion
Enhancement", "Quad Pixel Plus", "Active Contrast",
"Gamma Adjustment", "Black Level", "Film Mode",
"Digital Noise Reduction", "Monochrome" or "Range of
OPC".
• When set to "On", the Optical Picture Control (OPC)
senses the surrounding light and automatically adjusts
the backlight brightness. Make sure nothing obstructs
the OPC sensor, which could affect its ability to sense
surrounding light.
• When set to "On:Display", OPC effect displays on the
screen while the OPC adjusts the screen brightness.
3 Press a/b(or c/d) to select the desired setting,
and then press ENTER.
4 Press MENU to exit.
Selected item
Backlight
cbutton
The screen dims
Contrast
Brightness
For less contrast
For less
brightness
For less color
intensity
Skin tones
become reddish
For less
sharpness
Color
Tint
Sharpness
OPC:
dbutton
The screen
brightens
For more contrast
For more
brightness
For more color
intensity
Skin tones
become greenish
For more
sharpness
• For resetting all Picture adjustment items to the factory
preset values, press a/b to select "Reset", press ENTER,
press a/b to select "Yes", and then press ENTER.
OPC:
Advanced Picture Settings
This TV provides various advanced functions for
optimizing the picture quality.
C.M.S.
(Color Management System)
Color tone is managed using the six-color adjustment
setting.
C.M.S.-Hue: This is a standard to adjust the color either
more reddish or more bluish in tone.
C.M.S.-Saturation: Increases or decreases the
saturation of a selected color.
C.M.S.-Value: A higher value makes the image brighter.
A lower value makes the image darker.
• For resetting all adjustment items to the factory preset
values, press a/b to select "Reset", and then press
ENTER.
27
LC-40_46_52_60LE830U_E_03.indd 27
2011/01/31 20:49:34
On-Screen Display Menu
Color Gamut Range
You can set the color gamut range.
Standard: Standard color gamut.
Expanded: More vivid colors with expanded color gamut.
• "Color Gamut Range" is only available when AV MODE is
set to "MOVIE".
Color Temp.
(Color Temperature)
For a better white balance, use color temperature correction.
High:
Mid-High:
Middle:
Mid-Low:
Low:
White with bluish tone
White with reddish tone
White balance can be adjusted between a maximum of
+30 and a minimum of –30 for each color temperature.
R Gain (LO/HI): –30 through +30
G Gain (LO/HI): –30 through +30
B Gain (LO/HI): –30 through +30
• For resetting all adjustment items to the factory preset
values, press a/b to select "Reset", and then press
ENTER.
Motion Enhancement
Use Motion Enhancement to view fast-action video
more clearly.
Black Level
Adjusts on-screen black level to your preferred level.
High: The black level gets brighter.
Low: The black level gets darker.
• "Black Level" is available for input signal from Composite
Video, Component 480i and analog broadcasts (air and
cable).
Film Mode (3:2 pull-down)
Automatically detects a film-based source (originally
encoded at 24 frames/second), analyzes it then recreates
each still film frame for high-definition picture quality.
Advanced(High)/Advanced(Low): Select a desired level
to remove jerkiness from film contents.
Standard: Detects, analyzes, converts film source.
Off: Normal viewing mode.
• "Film Mode" does not function depending on input signal
type.
• "Standard" does not function when channel display shows
an input signal resolution of 480p, 720p, or 1080p.
• "Film Mode" is not available during PC format input.
• "Advanced(High)" and "Advanced(Low)" do not function
when you set AV MODE to “PC”.
Digital Noise Reduction
Produces a clearer video image.
120Hz High/120Hz Low: For obtaining a clearer image.
Off: Normal image.
Auto: Automatically adjusts the level of noise reduction.
High/Middle/Low: Select a desired level for viewing a
clearer video image.
Off: No adjustment.
• "Motion Enhancement" may cause image noise. If this
occurs, turn the function "Off".
• When AV MODE is set to "GAME" or "PC", or PC format is
being input, "Motion Enhancement" is not available.
• "Digital Noise Reduction" is not available when you set AV
MODE to "PC" or PC format is being input.
• When AV MODE is set to "GAME", "Auto" is not available.
Quad Pixel Plus
Enables smoother diagonal line by detailed dot control.
Monochrome
For viewing a video in monochrome.
On: Produces smooth diagonal line.
Off: No adjustment.
Active Contrast
Automatically adjusts the image contrast according to
the scene.
On: Automatically adjusts the image contrast.
Off: No adjustment.
Gamma Adjustment
Adjusts the differences of picture tones between bright
parts and dark parts. The adjustment range of the
gamma can be set to a maximum of +2 and a minimum
of –2 by pressing c or d.
On: For viewing in monochrome.
Off: Normal color.
Range of OPC
The brightness level range of the OPC sensor's automatic
adjustments can be set according to your preferences.
The adjustment range of the OPC sensor can be set to
a maximum of +16 and a minimum of –16.
Max.: –15 through +16
Min.: –16 through +15
• The "Range of OPC" settings are active only when "OPC"
is set to "On".
• The maximum setting cannot be set to a smaller number
than the minimum setting.
• The minimum setting cannot be set to a bigger number
than the maximum setting.
• Depending on the brightness of the surrounding light, the
OPC sensor might not operate if the adjustment range is
small.
28
LC-40_46_52_60LE830U_E_03.indd 28
2011/01/17 20:22:16
On-Screen Display Menu
Auto Volume
Audio Settings
You can adjust the sound quality to your preference
with the following settings.
Example
Audio
Settings
Menu
Different sound sources sometimes do not have the
same loudness level, such as a program and its
commercial breaks. The Automatic Volume Control
(Auto Volume) reduces this problem by equalizing
levels.
High: Reducing the loudness gaps among different
sound sources strongly.
Audio Settings
Middle:
Auto Volume
Low: Reducing the loudness gaps among different
sound sources slightly.
[Off]
Treble
[ 0] a15
Bass
[ 0] a15
b15
b15
• Audio Settings menu is grayed out when "Output Select" is
set to "Variable". (See page 32.)
Balance
[
0]
L
R
Surround
Surround
[Off]
The surround function produces Surround effect from
the speakers.
Bass Enhancer
[On]
Clear Voice
On: Makes it possible to enjoy natural, realistic surround
sound.
Off: Outputs the normal sound.
[Off]
Reset
1 Press MENU to display the MENU screen, and then
2
press c/d to select "Audio Settings".
Press a/b to select a specific adjustment item.
• Select "Auto Volume", "Surround", "Bass Enhancer" or
"Clear Voice", and then press ENTER to set each item.
3 Press a/b (or c/d) to select the desired setting,
4
and then press ENTER.
Press MENU to exit.
Selected item
Treble
Bass
Balance
cbutton
For weaker treble
For weaker bass
Decrease audio
from the right
speaker
• Audio Settings menu is grayed out when "Output Select" is
set to "Variable". (See page 32.)
• For some discs, setup may be required on your DVD/BD
player. In this case, please refer to the operation manual of
your DVD/BD player.
Bass Enhancer
This function allows you to enjoy bass-enhanced sound.
dbutton
For stronger treble
For stronger bass
Decrease audio
from the left
speaker
• Audio menu is grayed out when "Output Select" is set to
"Variable". (See page 32.)
• For resetting Audio adjustment items to the factory preset
values, press a/b to select "Reset", press ENTER, press
a/b to select "Yes", and then press ENTER.
On: Bass Enhancer function is on.
Off: Normal sound.
• Audio Settings menu is grayed out when "Output Select" is
set to "Variable". (See page 32.)
Clear Voice
This function emphasizes speech against background
noise for greater clarity.
• Audio Settings menu is grayed out when "Output Select" is
set to "Variable". (See page 32.)
29
LC-40_46_52_60LE830U_E_03.indd 29
2011/01/17 20:22:16
On-Screen Display Menu
Power Saving
Power Control
Power control setting allows you to save energy.
Example
Menu
Power
Control
Power Control
Audio Only
This function allows you to set the Power Saving level
in order to decrease the power consumption and
increase the backlight lifespan.
Standard: Optimizes power reduction based upon video
content. When set to "Standard", " " appears on the
screen.
Advanced: Optimizes power reduction based upon video
content and engages OPC. When set to "Advanced",
"
" appears on the screen.
Off: This function does not work.
Power Saving
[
Standard]
No Signal Off
[Enable]
No Operation Off
[Disable]
• "Power Saving" does not function when you set AV MODE
to "AUTO" or "DYNAMIC (Fixed)".
• You cannot select a different Power Saving item for each
AV MODE.
When "Power Saving" is set, the "OPC" settings for all AV
Modes will automatically change.
—If you set "OPC" to "On" when "Power Saving" is set to
"Standard", then the "Power Saving" setting will change
to "Advanced".
—When you change the "Power Saving" setting from
"Advanced" to "Off" or to "Standard", "OPC" will be set
to "Off".
—"AUTO" and "DYNAMIC (Fixed)" will remain set to "Off".
• When "Power Saving" is set to "Standard" or "Advanced",
the Power Saving leaf icon appears to the left of "OPC" in
the Picture Settings menu screen.
• You can select Power Saving by pressing POWER
SAVING on the remote control unit. (See page 22.)
No Signal Off
1 Press MENU to display the MENU screen, and then
press c/d to select "Power Control".
2 Press a/b to select a specific adjustment item,
This function allows the TV to automatically shut the
power down when there is no signal received.
Enable: The power will automatically shut down if there is
no signal for 15 minutes.
Disable: This function does not work.
and then press ENTER.
3 Press a/b (or c/d) to select the desired setting,
and then press ENTER.
4 Press MENU to exit.
• Skip this step for "Audio Only".
Audio Only
When listening to music from a music program, you
can turn the screen off and enjoy audio only.
On: Audio is output without screen image.
Off: Both screen images and audio are output.
• The screen image will return to normal when a button
(except those for audio adjustment, such as VOL, MUTE)
is pressed.
• When it is 5 minutes before the power shuts down, the
remaining time will start to keep appearing every minute.
• When a TV program finishes, this function may not operate.
No Operation Off
This function allows the TV to automatically shut the
power down when there is no operation.
Enable: The power will automatically shut down if there is
no operation for 3 hours.
Disable: This function does not work.
• When it is 5 minutes before the power shuts down, the
remaining time will start to keep appearing every minute.
30
LC-40_46_52_60LE830U_E_03.indd 30
2011/01/31 20:32:56
On-Screen Display Menu
Freeze
Allows you to capture and freeze a moving image that
you are watching.
System Options
Example
System
Options
Menu
• You can select Freeze by pressing FREEZE on the remote
control unit. See page 21 for details of Freeze function.
System Options
Change Audio
Allows you to change the audio when multiple audio is
available for the program you are watching.
View Option
AQUOS LINK Setup
Input Terminal Setting
Menu Design
Operation Lock Out
[Off]
Icon Light Up Setting
[On]
Demo Mode
1 Press MENU to display the MENU screen, and then
press c/d to select "System Options".
■ MTS/SAP stereo mode
The TV has a feature that allows reception of sound
other than the main audio for the program. This feature
is called Multi-channel Television Sound (MTS). The TV
with MTS can receive mono sound, stereo sound
and Secondary Audio Programs (SAP). The SAP feature
allows a TV station to broadcast other information,
which could be audio in another language or something
completely different like weather information.
You can enjoy Hi-Fi stereo sound or SAP broadcasts
where available.
• Stereo broadcasts: View programs like live sporting
events, shows and concerts in dynamic stereo sound.
• SAP broadcasts: Receive TV broadcasts in either MAIN
or SAP sound.
MAIN sound: The normal program soundtrack (either in
mono or stereo).
SAP sound: Listen to a second language, supplementary
commentary or other information. (SAP is mono sound.)
If stereo sound is difficult to hear.
• Obtain a clearer sound by manually switching to fixed
mono-sound mode.
2 Press a/b to select a specific adjustment item and
You can change MTS as shown below to match the
television broadcast signal.
3
Press ENTER to toggle between audio modes.
4
then press ENTER.
Press a/b (or c/d) to select the desired setting,
and then press ENTER.
Press MENU to exit.
View Option
These functions are useful for adjusting the audio
and video settings. The View Option functions can be
operated with the remote control unit.
APPS
The application window can be displayed by selecting
"APPS" on the MENU screen.
• You can display the application window by pressing APPS
on the remote control unit. (See page 22.)
View Mode
This function changes the screen size.
Select "View Option" on the menu to display the View
Mode menu screen.
The View Mode menu varies depending on the input source.
• You can select View Mode by pressing VIEW MODE on
the remote control unit.
— See page 24 for adjusting the video being input from a
TV, other audiovisual equipment, USB-Video, DLNAVideo or Internet applications.
— See page 56 for adjusting the video being input from a PC.
Examples: when receiving MTS and SAP
MONO
STEREO mode: STEREO
STEREO + SAP mode: ST(SAP)
SAP(ST)
MONO
MAIN + SAP mode: MAIN
MONO mode: MONO
SAP
■ Digital broadcasting audio mode
The types of audio transmitted in a digital broadcast include
SURROUND as well as MONO and STEREO. In addition, it
is possible for multiple audio tracks to accompany a single
video track.
Press ENTER to toggle between audio modes.
Example: when receiving Digital broadcasting
STEREO (Audio1)
STEREO (Audio2)
SURROUND (Audio3)
• MTS only operates while in TV mode.
31
LC-40_46_52_60LE830U_E_03.indd 31
2011/01/31 20:32:56
On-Screen Display Menu
Change CC
Allows you to change the Closed Caption display.
Select "Change CC" on the menu to display the Closed
Caption information.
• The information displayed varies depending on the program
you are watching.
• You can change Closed Caption by pressing CC on the
remote control unit. See page 23 for details of Closed
Caption function.
Input Terminal Setting
Audio Setup
You can output digital audio to an AV amplifier or
similar device whose DIGITAL AUDIO INPUT terminal
is connected to the DIGITAL AUDIO OUTPUT terminal
on the TV. Please select an audio output format
compatible with the audio format of the program you
are watching and the equipment connected.
PCM: The optical output terminal outputs audio signal
in PCM form. If your digital audio system does not
support Dolby Digital, select "PCM".
Dolby Digital: The optical output terminal outputs audio
signal in Dolby Digital form. It reproduces sound from
surround program of digital.
Input Skip
This setting allows you to skip the TV, HDMI or PC IN
Input ("TV", "PC IN", "HDMI 1", "HDMI 2", "HDMI 3"
and "HDMI 4") on the Input Selection operation.
Yes: Skips the input.
No: Does not skip input.
Input Label
Lets you set the input terminal displayed when using
the INPUT list or channel display. Press a/b/c/d to
select the new name for the input mode.
• Using the software keyboard, you can enter up to
10 characters for text. (See page 64.)
• You cannot change labels if the input source is TV, Home
Network (DLNA) or USB.
HDMI Setup
To watch an HDMI or PC IN equipment image, select
"HDMI 1", "HDMI 2", "HDMI 3" or "HDMI 4" from the
INPUT list using INPUT on the remote control unit or
on the TV.
Auto View:
Enable: To use View Mode based on signal
recognition, including an HDMI signal.
Disable: No function.
• Refer to your external equipment operation manual for the
signal type.
• When connecting a DVI-HDMI conversion adapter/cable to
the HDMI terminal, the image may not come in clearly.
Output Select
Allows you to select what controls the audio output.
Fixed: Sound via speaker is adjusted with VOLk/l on
the remote control unit or VOLl/k on the TV.
Sound via the AUDIO OUT terminal is not adjustable
and outputs at a consistent level.
Variable: Sound via the AUDIO OUT terminal is adjusted
with VOLk/l on the remote control unit or VOLl/k
on the TV.
Sound via speaker is muted.
Color System
Select the video signal system compatible with your
equipment from the list below:
Auto/NTSC/PAL-M/PAL-N
• "Color System" can only be set for the VIDEO 1 or 2.
• If you have already set the Secret No., input the 4-digit
secret number here. See page 35 for setting a secret
number.
Menu Design
Channel Selecting Effect
You can select whether to use transition effects when
changing channels.
Yes: A transition effect is used when the channel is
changed.
No: No function.
• In some cases, "Channel Selecting Effect" does not work.
Program Title Display
Select the CH display when changing channels for
digital broadcasting.
Yes: "Program Info." displays.
No: "Program Info." does not display.
Position
For adjusting a picture's horizontal and vertical
position.
H-Pos.: Centers the image by moving it to the left or
right.
V-Pos.: Centers the image by moving it up or down.
• For resetting adjustments to the factory preset values,
press a/b to select "Reset", and then press ENTER.
• When connecting a PC to the HDMI terminal, the image
position will be automatically adjusted. It cannot be
manually adjusted.
• The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
position-setting screen.
• Adjustments are stored separately according to input
source.
• "Position" does not work when USB mode, Home Network
(DLNA) mode or an Internet application is used.
32
LC-40_46_52_60LE830U_E.indb 32
2011/01/06 17:22:26
On-Screen Display Menu
Caption Setup
This function allows you to adjust the closed caption
screen appearance to suit your preference. You can
adjust 7 items: "Caption Size", "Font Style", "Foreground
Color", "Foreground Opacity", "Background Color",
"Background Opacity" and "Character Edge".
Example:
Selectable items available for "Font Style".
Default: The font specified by broadcasting station or
default font.
Type 0: Proportional font used in the MENU screen.
Type 1: Monospaced with serifs.
Type 2: Proportionally spaced with serifs.
Type 3: Monospaced without serifs.
Type 4: Proportionally spaced without serifs.
Type 5: Casual font type.
Type 6: Cursive font type.
Type 7: Small capitals.
• For resetting adjustments to the factory preset values,
press a/b to select "Reset", and then press ENTER.
• The default value depends on the broadcasting station.
Game Play Time
This function displays the elapsed game time so you
do not lose track of the time. To display the elapsed
time, select "GAME" for the AV MODE before starting
the game.
On: The elapsed time is displayed every 30 minutes when
you switch to GAME mode in external input mode.
Off: No adjustment.
Icon Light Up Setting
When this function is set to "On", the LED on the front
of the TV turns on.
• "On" is the factory preset value. If you want to turn off the
LED, set the function to "Off".
Demo Mode
You can select the image from several types of demo
mode.
Quattron/Quad Pixel Plus/Connected TV/Feature
Demo/Auto Play
If you have selected "Auto Play", you need to select the
desired playback type(s), and then set the playback time.
Continuous: Play Demos continuously.
10 min.: Play Demos every 10 minutes.
20 min.: Play Demos every 20 minutes.
• This function will be canceled when you press EXIT on the
remote control unit.
• When "Demo Mode" is set to "Quattron", "Connected TV"
or "Feature Demo", pressing FREEZE pauses/restarts
demo.
• "Demo Mode" may not be selected depending on input
signal type or application status.
• "Demo Mode" may be automatically canceled depending
on input signal type.
Operation Lock Out
This function locks the operation buttons on the TV
and the remote control.
Off: No adjustment.
RC Control Lock: All buttons on the remote control are
locked.
Button Control Lock: All buttons on the TV, except
POWER, are locked.
When “RC Control Lock” or “Button Control Lock” is
selected, a confirmation screen appears.
On: Locks the operation buttons.
Off: No adjustment.
• To unlock the buttons on the remote control by using the
touch sensor panel of the main unit (see page 25):
1 Press MENU to display the MENU screen, and then
press VOLl/k to select "System Options".
2 Press CHs/r to select "Operation Lock Out", and
then press INPUT.
3 Press CHs/r to select "Off", and then press INPUT.
4 Press MENU to exit.
• To unlock the buttons on the TV, press MENU on the
remote control, and then select "Off" in "Operation Lock
Out".
33
LC-40_46_52_60LE830U_E.indb 33
2011/01/06 17:22:27
On-Screen Display Menu
Air/Cable: Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable".
CH Search: Channel auto search makes the TV look for
all channels viewable in the set area.
Initial Setup
Example
Initial
Setup
Menu
Initial Setup
• If "Cable" is selected for Antenna setting, scrambled
channels are removed after the Channel search has been
completed.
Completed: The settings confirmation screen is displayed.
Confirm the information displayed on the screen.
EZ Setup
Broadcasting Setup
Internet Setup
Language
[English]
• See Initial Installation on pages 18 to 20 for setting each item.
• If no channel is found, confirm the type of connection
made with your TV and try "EZ Setup" again.
• If you select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
DivX® Setup
Broadcasting Setup
Individual Setup
Wall Mount Audio Setup
[No]
FAV APP Key Assign
Reset
1 Press MENU to display the MENU screen, and then
press c/d to select "Initial Setup".
2 Press a/b to select a specific adjustment item,
and then press ENTER.
• When you select "EZ Setup", "CH Setup", "Parental
CTRL" or "Reset", you can enter the 4-digit secret
number here. See page 35 for setting a secret number.
3 Press a/b (or c/d) to select the desired setting,
and then press ENTER.
4 Press MENU to exit.
EZ Setup
You can run EZ Setup again, even after setting up the
preset channels.
Language: Select from among 3 languages (English,
French and Spanish).
TV Location: Select "Home" or "Store" for the location
where you plan to install the TV. This product qualifies
for ENERGY STAR in Home mode default setting.
Home: “Power Saving” is set to "Advanced", and AV MODE is
set to "STANDARD".
Store: “Power Saving” is set to "Off" and AV MODE is set to
"DYNAMIC (Fixed)". Picture Reset and Feature Demo can be set.
Picture Reset: AV MODE will be set to "DYNAMIC (Fixed)"
regardless of whether Picture Reset is "On" or "Off". If you
select "On", AV MODE will be reset to "DYNAMIC (Fixed)"
if there is no operation for 30 minutes. When "Off" is
selected, AV MODE will be set to "DYNAMIC (Fixed)".
Feature Demo: When “On” is selected, after all the settings
are completed, the Feature Demo screen is displayed if
there is no operation for several minutes.
• ENERGY STAR qualification is based on AV MODE
"STANDARD".
CH Setup
If Initial Installation does not memorize all the channels
in your region, follow the instructions below to manually
memorize the channels.
Air/Cable: Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable".
CH Search: Channel auto search makes the TV look for
all channels viewable in the set area.
CH Memory: You can select the channels to skip in each
ANALOG (Air), ANALOG (Cable), DIGITAL (Air) and
DIGITAL (Cable).
On: Skips channels. (Channel selection disabled using CH
r/s.)
Off: Does not skip channels. (Channel selection enabled using
CHr/s.)
Remove Scrambled CH: This function makes the TV
look for and then delete digital cable channels that
are scrambled and so unavailable in the set area. The
process may take more than 20 minutes.
Yes: Starts to remove scrambled channels.
No: This function does not work.
• See Initial Installation on pages 18 to 20 for setting each item.
• If no channel is found, confirm the type of connection
made with your TV and try channel search again.
• If you select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
Antenna & Cable/STB: Select the type of connection
you will use to watch TV.
34
LC-40_46_52_60LE830U_E.indb 34
2011/01/06 17:22:27
On-Screen Display Menu
Favorite CH (Favorite Channel Setting)
This function allows you to program 4 favorite
channels, in 4 different categories. By setting the
favorite channels in advance, you can select your
favorite channels easily.
To register your favorite channel:
Select "Register" and then press ENTER. Press a/b/c/
d to select the position in the category, and then press
ENTER to register.
To delete your favorite channel:
Select "1 Data Clear" and then press ENTER. Press
a/b/c/d to select the channel you want to delete, and
then press ENTER. Select "Yes" and then press ENTER.
To delete all the favorite channels, select "All Data Clear".
• Before setting the channel, select the channel you want to
register as a favorite channel.
• You can display the "Favorite CH" screen by pressing
FAVORITE CH on the remote control.
Antenna Setup-DIGITAL
In order to receive digital air broadcasts, you need
a digital broadcast antenna. You can confirm the
antenna configuration through the "Antenna SetupDIGITAL" screen. If necessary, adjust the direction of
the antenna to obtain the maximum signal strength.
Signal Strength: The signal strength of DIGITAL channel
is displayed. The signal information is based on the
current channel.
Channel Strength: Input the 2-digit channel number
to check the signal strength of the selected channel.
Make sure the signal is strong enough for each
channel.
• This function is available for DIGITAL (Air) only.
Language
You can also select a language from the Initial Setup
menu. Select from among 3 languages: English,
French and Spanish.
Wall Mount Audio Setup
This selects the optimal audio for the program you are
currently watching even when the TV is mounted to a
wall.
Yes: Selects the optimal audio.
No: No adjustment.
FAV APP Key Assign
You can assign your favorite applications to the FAV
APP 1, 2, and 3 buttons on the remote control. After
assigning an application to a button, you can press
that button to display the top screen of the assigned
application.
Current Setup: Checks the current setting.
APP1/APP2/APP3: You can assign your favorite
applications displayed on the screen to these buttons.
Reset
If complex adjustments are made and the settings
cannot be restored to normal, you can reset the
settings to the factory preset values.
• If you have already set the Secret No., input the 4-digit
secret number here.
The Channel Setup settings will not be changed.
The Language settings will not be changed.
The Secret number settings will not be changed.
The TV Location settings will not be changed.
•
•
•
•
Individual Setup
Secret No.
Allows you to use a secret number to protect certain
settings from being accidentally changed.
IMPORTANT:
Three conditions must be met to enable the V-Chip (see
pages 36 to 37):
1. Secret No. is registered.
2. V-Chip/V-Chip (DTV Only) settings have been made.
• The “V-Chip (DTV Only)” will only be selectable when a new
rating system can be downloaded via digital broadcasting in the
U.S.
3. "Status" is set to "On".
■ Setting the Secret No.
You can set and change the secret number by using
0-9.
Yes: Changes or sets the Secret No.
No: The confirmation screen to clear the Secret No.
appears when the Secret No. has been set. When the
Secret No. has not been set, the previous screen will
be displayed.
■ Secret No. Clear
You can clear your secret number.
Yes: Your secret number is cleared.
No: Your secret number is not cleared.
• As a precautionary measure, make a note of your secret
number and keep it in a familiar place.
• If the secret number is cleared, the Status setting
automatically sets to "Off". "V-Chip" and "Status" will not
be selectable from the menu.
Parental CTRL
(Parental Control Setting)
Status
Used to enable or disable the parental control function.
This function will not be selectable from the menu if
you do not first configure your secret number.
On: Enables Parental CTRL.
Off: Disables Parental CTRL.
• For resetting adjustments to the factory preset values,
press a/b to select "Reset", and then press ENTER.
35
LC-40_46_52_60LE830U_E.indb 35
2011/01/06 17:22:27
On-Screen Display Menu
V-Chip
V-CHIP is an electronic filtering device built into your
TV. This tool gives parents a great degree of control
over broadcasts accessed by their children. It allows
parents to select programs judged suitable for child
viewing while blocking ones judged not suitable. It
does so automatically once you activate the V-CHIP
feature in your TV. "V-Chip" and "Status" will not be
selectable from the menu if you do not first configure
your secret number.
• The U.S. has two rating systems for viewing content: TV
Parental Guidelines and movie ratings.
• The TV Parental Guidelines work in conjunction with the
V-CHIP to help parents screen out inappropriate television
shows from their children.
• Movie ratings are used for original movies rated by the
Motion Picture Association of America (MPAA) as watched
on cable TV and not edited for television. The V-CHIP can
also be set to block MPAA-rated movies.
• The setting automatically enters "Block" for any ratings
below your selection.
• If Status is not set to "On", the configuration settings will
not work.
■ TV Parental Guidelines
Example
MPAA
TV Guidelines
TV-Y
Can. English Ratings
TV-Y7
Can. French Ratings
TV-G
L
TV-PG
S
D
TV-14
V
TV-MA
FV
NONE
Press a/b to adjust the item to your desired position.
" " indicates the item is blocked. Press MENU to exit.
Suggested age
TV-Y: All children.
TV-Y7: Directed to older children.
TV-G: General audience.
TV-PG: Parental Guidance suggested.
TV-14: Parents strongly cautioned.
TV-MA: Mature audience only.
Example
MPAA
■ MPAA (Voluntary movie rating system)
Example
MPAA
TV Guidelines
G
Can. English Ratings
PG
Can. French Ratings
PG-13
TV Guidelines
TV-Y
Can. English Ratings
TV-Y7
Can. French Ratings
TV-G
L
TV-PG
S
X
NONE
Press a/b to adjust the item to your desired position.
" " indicates the item is blocked. Press MENU to exit.
G: General audiences. All ages admitted.
PG: Parental guidance suggested. Some material may not be
suitable for children.
PG-13: Parents strongly cautioned. Some material may be
inappropriate for children under 13.
R: Restricted. Under 17 requires accompanying parent or
adult guardian (age varies in some jurisdictions).
NC-17: No one 17 and under admitted.
X: X is an older rating that is unified with NC-17 but may be
encoded in the data of older movies.
• Voluntary movie rating system only uses an age-based
rating.
TV-14
V
TV-MA
FV
NONE
R
NC-17
D
When setting an individual content-based rating item:
1 Press d or ENTER to access blocked content
items from the currently selected age-based rating
item.
2 Press a/b to select an individual item, and then
press ENTER to unblock it (" " is removed). Repeat
the same steps for the other items.
3 Press c or RETURN to register after all individual
content rating items are set.
Content
FV: Fantasy violence.
V: Violence.
S: Sexual situation.
L: Adult language.
D: Sexually suggestive dialog.
Content
Rating
FV
V
S
L
D
TV-Y
TV-Y7
Suggested
age
TV-G
TV-PG
TV-14
TV-MA
: The content rating can be set, but this rating is not
normally broadcast by TV stations.
: Content rating can be set.
36
LC-40_46_52_60LE830U_E.indb 36
2011/01/06 17:22:27
On-Screen Display Menu
Canadian Rating Systems (Canadian English ratings
and Canadian French ratings)
• The TV rating systems in Canada are based on the
Canadian Radio-Television and Telecommunications
Commission (CRTC) policy on violence in television
programming.
• While violence is the most important content element to
be rated, the structure developed takes into consideration
other program content like language, nudity, sexuality and
mature themes.
• When setting the V-CHIP on the Canadian system you
can choose either the Canadian English ratings or the
Canadian French ratings.
■ Canadian English Ratings
Example
MPAA
TV Guidelines
E
Can. English Ratings
C
Can. French Ratings
C8+
G
PG
14+
18+
NONE
Press a/b to adjust the item to your desired position.
" " indicates the item is blocked. Press MENU to exit.
E: Exempt: Includes news, sports, documentaries and other
information programming; talk shows, music videos, and
variety programming.
C: Children: Intended for younger children under the age of 8
years. Pays careful attention to themes that could threaten
their sense of security and well-being.
C8+: Children over 8 years old: Contains no portrayal
of violence as the preferred, acceptable, or only way
to resolve conflict; nor encourage children to imitate
dangerous acts which they may see on the screen.
G: General: Considered acceptable for all age groups.
Appropriate viewing for the entire family, contains very little
violence, physical, verbal or emotional.
PG: Parental Guidance: Intended for a general audience, but
may not be suitable for younger children (under the age of 8)
because it could contain controversial themes or issues.
14+: Over 14 years: Could contain themes where violence
is one of the dominant elements of the storyline, but it
must be integral to the development of plot or character.
Language usage could be profane and nudity present
within the context of the theme.
18+: Adults: Intended for viewers 18 years and older and
might contain depictions of violence, which while related to
the development of plot, character or themes, are intended
for adult viewing. Could contain graphic language and
portrayals of sex and nudity.
■ Canadian French Ratings
Example
MPAA
TV Guidelines
E
Can. English Ratings
G
Can. French Ratings
8ans+
13ans+
16ans+
18ans+
NONE
Press a/b to adjust the item to your desired position.
" " indicates the item is blocked. Press MENU to exit.
E: Exempt programming.
G: General: All ages and children, contains minimal direct
violence, but may be integrated into the plot in a humorous
or unrealistic manner.
8ans+: General but inadvisable for young children: May
be viewed by a wide public audience, but could contain
scenes disturbing to children under 8 who cannot
distinguish between imaginary and real situations.
Recommended for viewing with parent.
13ans+: Over 13 years: Could contain scenes of frequent
violent scenes and therefore recommended for viewing with
parent.
16ans+: Over 16 years: Could contain frequent violent scenes
and intense violence.
18ans+: Over 18 years: Only for adult viewing. Could contain
frequent violent scenes and extreme violence.
■ How to temporarily release the V-CHIP BLOCK
When the V-CHIP BLOCK is working and censors a
broadcast, "V-CHIP HAS BEEN ACTIVATED." displays.
1 Press ENTER while the V-CHIP is working, and
then the secret number setting menu displays.
2 Input the 4-digit secret number by using 0–9. At this
time V-CHIP BLOCK temporarily releases.
■ Reactivating the temporarily released V-CHIP
BLOCK
You can reactivate the temporarily released V-CHIP
BLOCK as shown below.
• Select "Status" setting from the Parental CTRL menu to
reactivate BLOCK. (See page 35.)
• Select "V-Chip" setting ("MPAA", "TV Guidelines", "Can.
English Ratings" or "Can. French Ratings") from the
Parental CTRL to reactivate BLOCK. (See pages 36 to 37.)
• Switch off the TV power.
• Performing any of the three above will activate the V-CHIP
BLOCK.
37
LC-40_46_52_60LE830U_E.indb 37
2011/01/06 17:22:27
On-Screen Display Menu
2 Press a/b to select “Software Update”, and then
Information
press ENTER.
Example
Information
Menu
• If you have already set the Secret No., go to step 3.
Example
Menu
Information
Information
Information
Identification
Identification
Digital Caption Info.
Digital Caption Info.
Software Update
Software Update
Netflix Help
Vudu Help
1 Press MENU to display the MENU screen, and then
2
3
4
press c/d to select "Information".
Press a/b to select a specific adjustment item,
and then press ENTER.
Press a/b (or c/d) to select the desired setting,
and then press ENTER.
Press MENU to exit.
Identification
The current version of the TV software is displayed.
Digital Caption Info.
(Digital Caption Information)
This function allows viewing of digital closed caption
information for the digital broadcast program being viewed.
• This list is not displayed for analog broadcasts or external
input audio/video.
• This information is not included in CC1, CC2, Text1, or
Text2, and is not displayed in a list.
Software Update
This is used to upgrade the system software to
enhance the TV functions.
3 Input the 4-digit secret number by using 0-9.
Software Update
Enter your Secret No.
4 Press a/b to select “Manual Update” or “Auto
Update Setting”, and then press ENTER.
• The operations thereafter vary depending on the setting.
Manual Update
Select the method for manually updating the software.
USB Update: Updates the software using a USB memory
device containing the update file. (See pages 39 to 40.)
Network Update: Downloads the update file via the
network and then updates the software. (See page 39.)
• A broadband connection and Internet Setup are required to
update the software using the network. (See pages 60 to
63.)
• It may take time to access and download the update
depending on the Internet connection and other factors.
Auto Update Setting
When the TV is on, or when an Internet application
is being accessed, this function enables the TV
to connect to the network and check for updates
automatically.
Yes: Enables Auto Update Setting.
No: Disables Auto Update Setting.
1 Press MENU to display MENU screen, and then
When an update is available, a message is displayed.
Press c/d to select "Yes", and then press ENTER to
display the download screen. (See page 39.)
press c/d to select “Information”.
Yes
No
• This function does not work when a broadband connection
or Internet Setup is not available.
• A message may also be displayed when an application is
running.
The message varies depending on the application.
38
LC-40_46_52_60LE830U_E_03.indd 38
2011/01/26 22:06:39
On-Screen Display Menu
■ Updating the Software via the Network
1 Press a/b on the Manual Update screen to select
"Network Update", and then press ENTER.
• The TV connects to the network and checks for updates.
• To cancel, press ENTER.
Connecting to Internet..
Checking for the latest software version..
Accessing..
Abort
CAUTION
• Do not unplug the AC cord while the software is
being updated.
4 When the software is successfully updated, a
screen is displayed indicating that the update
process is completed.
A screen indicating that the update is completed
is displayed. 4 seconds later, the TV restarts
automatically.
Software update is complete.
2 The current version of the TV and the latest version
Update Version
of software are displayed. To update the TV
software, select “Yes”, and then press ENTER.
Latest software version has been found.
A software update is available.
Proceed with update?
XXXXXXXX
• If the software was not updated successfully, check the
broadband connection and Internet Setup, and then try
updating the software again.
Current Version
Failed to complete update.
Please retry from Software Update menu.
XXXXXXXX
Latest Version
XXXXXXXX
OK
Estimated Update Time
XX
Update time may change depending on the network environment
Yes
No
• When a server connection cannot be established or an
update is not available, a message is displayed.
If a server connection cannot be established, check the
broadband connection and Internet Setup.
Cannot reach the server.
Check the network settings and try again.
OK
■ Updating the Software with a USB Memory Device
To check for the availability of a software update, visit
http://www.sharpusa.com/products/support/. If you
have any questions, please
call 1-800-BE-SHARP (800-237-4277).
CAUTION
• Do not remove the USB memory device or unplug
the AC cord while the software is being updated.
• Be sure to properly follow the whole procedure
described below, step by step. Otherwise, for
example, the TV cannot read the data in the USB
memory device and software updating will fail.
1 Insert the USB memory device with the update file
The TV does not need to be updated.
into the USB 1 or USB 2 terminal on the TV.
• When you update the software, use only one USB
terminal. Either USB 1 or USB 2 is usable.
OK
3 After the update file is downloaded, the software
update process begins.
Downloading the latest software..
Update Version
XXXXXXXX
30%
Abort
Updating to the latest software..
or
Update Version
XXXXXXXX
50%
Remote control operation is disabled during update process.
2 Press a/b on the Manual Update screen to select
"USB Update", and then press ENTER.
Do not unplug AC cord.
39
LC-40_46_52_60LE830U_E_03.indd 39
2011/01/26 22:06:39
On-Screen Display Menu
3 Press ENTER to start checking the data in the USB
memory device.
5 To update the TV software with the update file,
select “Yes”, and then press ENTER.
Software update file is detected
in the USB memory device.
Start update?
Insert the USB memory device
containing the software update file.
Current Version
Update Version
: UXXXXXX1
: UXXXXXX2
OK
Yes
No
4 During the data checking, “Checking” blinks.
Now checking the data
in the USB memory device.
Example
Now updating
Update Version
: UXXXXXX2
Checking
30%
Remote Control operation is disabled during Update process.
• The current version of the TV software and the version
of the update file on the USB memory device are
displayed.
Example
Software update file is detected
in the USB memory device.
Start update?
Current Version
Update Version
CAUTION
• Do not remove the USB memory device or unplug
the AC cord while the software is being updated.
6 When the software is successfully updated, a
: UXXXXXX1
: UXXXXXX2
Yes
Do not unplug AC cord.
No
screen is displayed indicating that the update
process is completed.
After this screen is displayed, the TV automatically
turns off and then turns on again.
Example
• If the USB memory device is not properly installed or
the correct update file cannot be found on the USB
memory device, an error message is displayed.
Check the file on the USB memory device, and then
reinsert the USB memory device correctly.
Software update is complete.
Update Version
: UXXXXXX2
OK
Software update file is not detected in the USB memory device.
Confirm that you have transferred the file
to the USB memory device and retry software update.
• If the update has failed, check the file in the USB
memory device and try Software Update again.
OK
Failed to complete update.
Retry Software Update.
If system Update fails again,
contact the customer service center.
There is more than one software file in the USB memory device.
Confirm that only the software update file is
in the USB memory device.
Update Version
: UXXXXXX2
OK
OK
7 After the screen shown below is displayed, press
ENTER.
System software was
successfully updated.
Remove the USB memory device.
OK
8 Remove the USB memory device.
40
LC-40_46_52_60LE830U_E.indb 40
2011/01/06 17:22:28
Enjoying Photo/Music/Video Playback
You can connect the TV to a USB memory device, USB hard drive or home network (DLNA) server to enjoy
viewing pictures, listening to music, and watching videos.
• Depending on the USB memory device/USB hard drive/home network (DLNA) server, the TV may not be able to recognize the
recorded data.
• It may take time to read the recorded data if the USB memory device/USB hard drive/home network (DLNA) server contains
many files or folders.
• Use only alphanumeric characters for naming files.
• File names over 80 characters (may vary depending on character set) may not be displayed.
Connecting a USB Memory Device/USB Hard Drive
Insert the USB memory device with recorded photos, music or videos into the USB 1 or USB 2 terminal on the TV.
• If USB memory devices are inserted into both terminals, the USB 1 terminal has priority.
or
• When connecting a USB hard drive, be sure to use a hard drive with an AC adapter.
• Do not remove a USB memory device or memory card from the TV while transferring files, using the slide show function, or
switching screens, or before you exit "USB" from the INPUT list.
• Do not insert and remove a USB memory device/USB hard drive to and from the TV repeatedly.
• When using a card reader, be sure to insert Memory first before using the card reader.
• USB input cannot be selected when displaying the browser. Close the browser first.
CAUTION
• Do not use a USB extension cable when connecting a USB memory device to the USB terminal on the TV.
• Using a USB extension cable with the USB memory device may prevent the TV from performing correctly.
Connecting a Home Network (DLNA) Server
Connect the TV to the home network (DLNA) server using an ETHERNET cable.
ETHERNET cable
Home network (DLNA) server
Router
• Do not disconnect a home network (DLNA) server from the TV while transferring files, when a screen is switching to another or
before you exit "Home Network (DLNA)" from the INPUT list.
• Do not connect and disconnect a home network (DLNA) server from the TV repeatedly.
41
LC-40_46_52_60LE830U_E.indb 41
2011/01/06 17:22:29
Enjoying Photo/Music/Video Playback
Select the Files to Play Back
• You cannot switch the input mode if a USB memory device
is not connected.
• You do not need to select the drive/server in step 2 when
there is only one drive in the connected USB memory
device or there is only one home network (DLNA) server
connected to the TV.
• 16 is the maximum number of USB drives and 10 is the
maximum number of home network (DLNA) servers that
can be displayed.
• "VIEW MODE" is fixed during the Photo or Music mode.
During "Video mode", you can select "Auto" or "Original".
• The key guide display disappears automatically after a
set time. To display the key guide display again, press
DISPLAY.
■ When displaying the data with the APPS
The Media screen can be displayed even by using the
application window.
• To play back data on a USB memory device, insert the
USB memory device on the TV. USB mode is selected
automatically. (Go to step 2)
• Use the following procedure to switch back to USB mode
after switching from USB mode to another mode.
1 Select "USB" or "Home Network (DLNA)" from
INPUT list screen.
2 Press D.
■ USB memory device
Press a/b/c/d to select the drive where you
want to find your files, and then press ENTER.
1 Press APPS to display the application window.
2 Press a/b/c/d to select "USB Media" or "Home
Network (DLNA)", and then press ENTER.
• If "
" is displayed after you switch to USB mode,
check the USB connection.
• If "
" is displayed after you switch to Home Network
(DLNA) mode, check your TV's network settings and
connection.
• You can also display the Media screen by pressing
FAV APP on the remote control unit. See page 35 for
details on the FAV APP Key Assign function.
Example
Drive1
Drive2
Drive5
Drive6
Drive3
Drive4
• If the TV is turned off and then on again, the number
assigned to the USB drive may change.
■ Home Network (DLNA)
Press a/b to select the server where you want to
find your files, and then press ENTER.
Example
Server1
Server2
3 Press c/d to select "Photo", "Music" or "Video",
and then press ENTER.
Example
Photo
Music
Video
4 Press c/d to select the desired folder, and then
press ENTER.
42
LC-40_46_52_60LE830U_E.indb 42
2011/01/06 17:22:29
Enjoying Photo/Music/Video Playback
Viewing Individual Photos
The photo selected on the thumbnail selection screen
is displayed.
Buttons for individual display operation
Playing Back Files on a USB
Memory Device
Photo Mode
Buttons
c/d
Viewing Thumbnails
Example
...
picture 1
picture 2
picture 3
picture 4
picture 5
...
RETURN
A (red)
B (green)
Description
Go to the previous/next photo in the same
directory.
Return to the thumbnail selection screen.
Rotate the photo by 90 degrees to the left.
Rotate the photo by 90 degrees to the right.
• Rotating photos only applies to the temporarily selected
item and this setting is not saved.
• The key guide display disappears automatically after a
set time. To display the key guide display again, press
DISPLAY.
Slide Show
The photos displayed on the thumbnail selection
screen are displayed as a slide show.
Buttons for slide show operation
Buttons
RETURN
D (yellow)
Buttons for thumbnail operations
Buttons
a/b/c/d
ENTER
RETURN
A (red)
B (green)
C (blue)
D (yellow)
Description
Select a desired item.
Display the photo.
Return to the previous process.
Select the images to be displayed. Press
this button to add or remove a checkmark.
Display the music list screen.
Start the slide show.
Display the USB MENU screen.
Description
Return to the thumbnail selection screen.
Display the USB MENU screen.
• The selected BGM is played repeatedly.
• The slide show continues until you press RETURN.
• For setting the slide show speed, select "Select Slide Show
Interval" on the USB MENU screen.
• The key guide display disappears automatically after a
set time. To display the key guide display again, press
DISPLAY.
• When there are invalid photo files, the X mark will be
displayed for the file.
• You can see the file name, shooting date, file size and pixel
size of the selected photo in the lower-left corner of the
screen (shooting date is only available in the EXIF file format).
43
LC-40_46_52_60LE830U_E.indb 43
2011/01/06 17:22:29
Enjoying Photo/Music/Video Playback
Buttons for slide show BGM select operation
Buttons
a/b/c/d
ENTER
RETURN
A (red)
B (green)
C (blue)
D (yellow)
Description
Select a desired item.
Play music.
Return to the previous process.
Select the music to be played back. Press
this button to add or remove a checkmark.
Stop music.
Play/Pause music.
Display the USB MENU screen.
4 Press RETURN to display the thumbnail selection
screen, and then press C to start the slide show
and the background music.
USB Menu
Example
USB MENU
Select Slide Show Intrerval
[10sec]
• All of the music files are selected by default.
■ Set/Reset All Slide Show Image
Set or reset the images to be displayed.
Select Slide Show BGM
Set All Slide Show Image
1 Press D to display the USB MENU screen.
2 Press a/b to select "Set All Slide Show Image"/
Reset All Slide Show Image
Remove USB Device
"Reset All Slide Show Image", and then press
ENTER.
■ Select Slide Show Interval
Specify the length of time before the next image
appears.
• When you select "Set All Slide Show Image",
checkmarks are added to all the images.
• When you select "Reset All Slide Show Image", remove
all the checkmarks from all the images.
1 Press D to display the USB MENU screen.
2 Press a/b to select "Select Slide Show Interval",
Example
and then press ENTER.
3 Press a/b to select "5sec", "10sec", "30sec" or
...
picture 1
picture 2
picture 3
picture 4
picture 5
...
"60sec", and then press ENTER.
• Depending on the photo files, the length of the slide show
interval may differ from the selected interval time.
■ Select Slide Show BGM
You can select the music to be played in the
background while the slide show is being displayed.
1 Press D to display the USB MENU screen.
2 Press a/b to select "Select Slide Show BGM",
3 Press C to start the slide show.
and then press ENTER.
• The list screen is displayed.
• You can display the list screen by pressing B on the
thumbnail selection screen.
3 Select the music.
• Checkmarks are added to the selected music.
Example
...
music 1
music 2
SONG_01.MP3
SONG_02.MP3
SONG_03.MP3
SONG_04.MP3
SONG_05.MP3
SONG_06.MP3
SONG_07.MP3
SONG_03.MP3
music 3
music 4
music 5
I
I
I
I
I
I
I
3:42
4:55
4:35
4:08
4:20
3:55
4:26
• If no images have been selected, "Cannot display the data"
is displayed and the slide show does not start.
■ Remove USB Device
1 Press D to display the USB MENU screen
2 Press a/b to select "Remove USB Device", and
...
3
then press ENTER.
Press c/d to select "Yes"/"No", and then press
ENTER.
• When you select "Yes", the USB device can be safely
removed.
0:14 / 4:35
44
LC-40_46_52_60LE830U_E.indb 44
2011/01/06 17:22:29
Enjoying Photo/Music/Video Playback
Video Mode
Example
...
video 1
video 2
video 3
VIDEO_01.avi
VIDEO_02.divx
VIDEO_03.divx
VIDEO_04.avi
VIDEO_05.divx
VIDEO_06.divx
VIDEO_07.avi
video 4
video 5
I
I
I
I
I
I
I
...
3:42
4:55
4:35
4:08
4:20
3:55
4:26
Buttons for file selecting operations
Buttons
a/b/c/d
ENTER
Music Mode
Example
...
music 1
music 2
music 3
music 4
music 5
I
I
I
I
I
I
I
SONG_01.MP3
SONG_02.MP3
SONG_03.MP3
SONG_04.MP3
SONG_05.MP3
SONG_06.MP3
SONG_07.MP3
SONG_03.MP3
...
RETURN
A (red)
3:42
4:55
4:35
4:08
4:20
3:55
4:26
D (yellow)
Description
Select a desired item.
When selecting a video file: Play the
video.
Return to the previous process.
Select/deselect items (checkmarks are
addded to the selected items).
Display the USB MENU screen.
0:14 / 4:35
Buttons for playing mode
Buttons
a
Buttons for music mode
Buttons
a/b/c/d
ENTER
RETURN
A (red)
Description
Select a desired item.
Play music.
Return to the previous process.
Select the music to be played back. Press
this button to add or remove a checkmark.
Stop music.
Play/Pause music.
Display the USB MENU screen.
B (green)
C (blue)
D (yellow)
• When there are invalid music files, the X mark will be
displayed for the file.
• The displayed play time may differ slightly from the actual
play time depending on the files.
USB Menu
Example
USB MENU
Set All Auto Play
Reset All Auto Play
Remove USB Device
*
* See page 44 for details on the Remove USB Device
function.
■ Set/Reset All Auto Play
Set or reset the music to be played back.
1 Press D to display the USB MENU screen.
2 Press a/b to select "Set All Auto Play"/"Reset All
Auto Play", and then press ENTER.
b
d
c
RETURN
ENTER
A (red)
B (green)
C (blue)
D (yellow)
0-9
Description
Go to the beginning of a file by pressing a
once and the previous file by pressing a
twice.
Go to the next file.
The fast forward speed changes every time
you press d. After playing to the end, the TV
goes to the next file and starts to play.
The reverse speed changes every time you
press c. After going back to the beginning,
the TV starts to play the same file.
Go back to the file selection screen.
Pause the video.
Jump to the scene where playback was last
stopped.
Stop a video.
Display the USB operation panel.
Display the USB MENU screen.
Jump to a point in the video during playback
of a file without chapters.
You can jump to a later point by pressing a
higher number.*
* During playback of a file without chapters, playback points
are set automatically. Playback points are set at intervals of
a one-tenth of playback time.
Example for a file with a playback time of 100 minutes:
Pressing 1 jumps 10 minutes forward, and pressing 2 jumps
20 minutes forward. Pressing 0 returns to the start of the file
being played back.
• When you select "Set All Auto Play", checkmarks are
added to all the music files.
• When you select "Reset All Auto Play", remove all the
checkmarks from all the music files.
3 Press C to play back the music.
• If no music files have been selected, "Cannot playback the
audio file" is displayed and the music is not played back
automatically.
LC-40_46_52_60LE830U_E.indb 45
45
2011/01/06 17:22:29
Enjoying Photo/Music/Video Playback
■ Using the operation panel
You can use the operation panel for video playback
operations.
You can call up this operation panel by pressing
MENU after you press a/b to select "USB Operation
Panel" from "System Options" > "View Option".
USB Menu
Menu for file selecting operations
Example
USB MENU
Set All Auto Play
Reset All Auto Play
System Options
PLAY
*
Remove USB Device
0:04:11 / 0:07:42
* See page 44 for details on the Remove USB Device
function.
Audio
Title
•
d
Œ

)
/
Audio
+
CC
Title
Resume jump
CC
Resume
jump
Hold down to go in reverse.
Starts playback.
Hold down to fast forward.
Video without chapters: Press one time
to return to the previous playback point.*
Press two times to return to the previous file.
Video with chapters: Press one time to
return to the previous chapter. Press two
times to return to the previous file.
Sets pauses and still pictures.
Video without chapters: Press one time to
advance to the next playback point.* Press
two times to display the next file.
Video with chapters: Press one time to
advance to the next chapter. Press two
times to display the next file.
Change the audio when multiple audio is
available for the video you are watching.
Playback stops.
Change the Closed Caption display.
Displays the title list.
Jump to the scene where playback was
last stopped.
* During playback of a file without chapters, playback points
are set automatically. Playback points are set at intervals of
a one-tenth of playback time.
Example for a file with a playback time of 100 minutes:
Playback points are set every 10 minutes. Pressing /
one time after viewing the file for 15 minutes jumps to the
20-minute playback point.
• Reverse/fast forward continues from one file to another
during continuous playback.
• Use "CC" on the operation panel to change the Closed
Caption display. You can also switch the Closed Caption
display by using "System Options" > "View Option" >
"Change CC" or by pressing CC on the remote control unit.
• Use "Audio" on the operation panel to change the audio.
You can also switch the audio by using "System Options" >
"View Option" > "Change Audio".
■ Set/Reset All Auto Play
Set or reset the video to be played back.
1 Press D to display the USB MENU screen.
2 Press a/b to select "Set All Auto Play"/"Reset All
Auto Play", and then press ENTER.
• When you select "Set All Auto Play", checkmarks are
added to all the video files.
• When you select "Reset All Auto Play", remove all the
checkmarks from all the video files.
3 Press ENTER to play back the video.
Menu for playing mode
Example
USB MENU
Title
Chapter
Show Video Information
*
Remove USB Device
* See page 44 for details on the Remove USB Device
function.
■ Title/Chapter
This function can be used for files without a title list or
chapters.
Select the title or chapter you want to play back.
1 Press D to display the USB MENU screen.
2 Press a/b to select "Title" or "Chapter", and then
3
press ENTER.
Press a/b to select the desired title or chapter,
and then press ENTER.
• The selected title or chapter is played back.
• "0-9" is displayed for files without chapters. Playback
jumps to the playback point of the selected number.
• If there is Edition information, this screen is displayed when
the title is selected.
■ Show Video Information
The information of the current file is displayed.
1 Press D to display the USB MENU screen.
2 Press a/b to select "Show Video Information",
and then press ENTER.
46
LC-40_46_52_60LE830U_E_04.indd 46
2011/01/26 22:08:26
Enjoying Photo/Music/Video Playback
DivX® Setup
This is the function to confirm your registration code.
You need to register the code at http://www.divx.com.
USB Device Compatibility
1 Press MENU to display the menu screen.
2 Press c/d to select "Initial Setup", and then press
File system
Photo file
format
Music file
format
USB device
ENTER.
3
Press a/b to select "DivX® Setup", and then
press ENTER.
®
■ DivX VOD registration
You can find your registration code on this menu. You
need to register the TV at http://www.divx.com before
playing the DivX content.
®
■ DivX VOD deregistration
You can find your deregistration code on this menu.
You need to deregister the TV at http://www.divx.com
to release the registration.
USB Memory, USB card reader (Mass
Storage class), USB hard drive
FAT/FAT32/NTFS (USB hard drive only)
JPEG (.jpg) (DCF2.0 compliant)
MP3 (.mp3)
Bitrate: 32k, 40k, 48k, 56k, 64k, 80k,
96k, 112k, 128k, 160k, 192k, 224k,
256k, 320kbps
Sampling frequency: 32k, 44.1k, 48kHz
Video file format
File
Container
Video
extension
DivX 3.11/4.x/5.1/6.0
XviD
.avi
AVI
H.264
MPEG4
Motion Jpeg
DivX 3.11/4.x/5.1/6.0
XviD
.mkv
MKV
H.264
MPEG4
DivX 3.11/4.x/5.1/6.0
XviD
.asf
MPEG4
ASF
.wmv
VC-1
Windows Media Video v9
.mp4
H.264
MP4
.mov
MPEG4
(SMP4)
.3gp
Motion Jpeg
.vro
MPEG2
.mpg
PS
MPEG1
.mpeg
Audio
MP3
AC3
LPCM
ADPCM
MP3
AC3
LPCM
ADPCM
MP3
AC3
LPCM
WMA
MP3
AAC
AC3
MPEG
LPCM
•
•
•
•
Progressive format jpeg files are not supported.
USB 1.1 devices may not be played properly.
Operation using USB hubs is not guaranteed.
Some video file formats may not be played depending on
the file.
• Some images may not be displayed in the appropriate
aspect ratio depending on the file format.
47
LC-40_46_52_60LE830U_E_04.indd 47
2011/01/31 21:28:15
Enjoying Photo/Music/Video Playback
Playing Back Files on a Home
Network (DLNA) Server
Viewing Individual Photos
The photo selected on the thumbnail selection screen
is displayed.
Buttons for individual display operation
Buttons
c/d
RETURN
A (red)
B (green)
Description
Go to the previous/next photo in the same
directory.
Return to the thumbnail selection screen.
Rotate the photo by 90 degrees to the left.
Rotate the photo by 90 degrees to the right.
• Rotating photos only applies to the temporarily selected
item and this setting is not saved.
Photo Mode
Viewing Thumbnails
Example
/Root/Pictures/Folders/Pictures
Photo2
FolderA
FolderB
Slide Show
The photos displayed on the thumbnail selection
screen are displayed as a slide show.
Buttons for slide show operation
Buttons
RETURN
D (yellow)
Description
Return to the thumbnail selection screen.
Display the Home Network (DLNA) Menu
screen.
FolderA
• The slide show continues until you press RETURN.
• For setting the slide show speed, display the Home
Network (DLNA) Menu screen.
Buttons for thumbnail operations
Buttons
a/b/c/d
ENTER
RETURN
C (blue)
D (yellow)
Description
Select a desired item.
When selecting a folder icon: Enter this
directory.
When selecting a photo thumbnail: Enlarge
the photo.
Return to the previous process.
Start the slide show.
Display the Home Network (DLNA) Menu
screen.
• When there are invalid photo files, the X mark will be
displayed for the file.
• You can see the file name, shooting date, file size and pixel
size of the selected photo in the lower-left corner of the
screen (shooting date is only available in the EXIF file format).
Home Network (DLNA) Menu
Example
Home Network (DLNA) Menu
5sec
10sec
30sec
60sec
■ Select Slide Show Interval
Specify the length of time before the next image
appears.
1 Press D to display the Home Network (DLNA)
Menu screen.
2 Press a/b to select "5sec", "10sec", "30sec" or
"60sec", and then press ENTER.
• Depending on the photo files, the length of the slide show
interval may differ from the selected interval time.
48
LC-40_46_52_60LE830U_E.indb 48
2011/01/06 17:22:30
Enjoying Photo/Music/Video Playback
Video Mode
Example
/Root/Videos/Folders/
Videos
wmv
VIDEO_02
VIDEO_03
VIDEO_04
VIDEO_05
VIDEO_06
VIDEO_07
4:55
4:35
4:08
4:20
3:55
4:26
Buttons for file selecting operations
Buttons
a/b/c/d
ENTER
Music Mode
Example
/Root/Music/Folders/Music
Folder1
Folder2
Folder3
SONG_03
SONG_04
SONG_05
SONG_06
SONG_07
4:35
4:08
4:20
3:55
4:26
RETURN
Buttons for playing mode
Buttons
a
Buttons for music mode
Buttons
a/b/c/d
ENTER
RETURN
B (green)
C (blue)
Description
Select a desired item.
When selecting a folder icon: Enter this
directory.
When selecting a music file: Play music.
Return to the previous process.
Stop music.
Play music.
• When there are invalid music files, the X mark will be
displayed for the file.
• The displayed play time may differ slightly from the actual
play time depending on the files.
Description
Select a desired item.
When selecting a folder icon: Enter this
directory.
When selecting a video file: Play the
video.
Return to the previous process.
b
d
c
RETURN
ENTER
B (green)
C (blue)
Description
Go to the beginning of a file by pressing a
once and the previous file by pressing a
twice.
Go to the next file.
Jump forward in a video. *1
Jump back in a video. *1
Go back to the file selection screen.
Play/Pause the video.
Stop a video.
Display the home network (DLNA) operation
panel.*2
*1 Jump forward/back may not be available depending on the
files.
*2 See page 46 for details on the operation panel.
You can call up the operation panel by pressing MENU
after you press a/b to select "Home Network (DLNA)
Operation Panel" from "System Options" > "View Option".
Home Network (DLNA) Server Compatibility
Photo file format
Music file format
Video file format
JPEG
LPCM, MP3
MPEG2-PS, MPEG2-TS,
WMV, ASF, MP4, MOV, AVI
• Progressive format jpeg files are not supported.
• Some video file formats may not be played depending on
the file or the server.
49
LC-40_46_52_60LE830U_E.indb 49
2011/01/06 17:22:30
Other Viewing Options
Presetting Remote Control Function
Operating the Connected Equipment
You can operate the connected AV products (AV
receiver, cable box, SAT tuner, DTV, VCR, DVD, BD,
LD) using the presetting manufacturer function of your
remote control unit.
To operate the connected equipment, press STB,
DVD•VCR or AUDIO to select your device. (STB
(cable/satellite set-top box), DVD, BD, VCR or AUDIO.)
The remote control unit button will function as follows.
• When you operate VCR, DVD or BD, press INPUT to select
the terminal connected to your device.
• CABLE and SAT cannot be selected at the same time.
1
1 POWER (SOURCE)
• Turns the connected equipment power on and off.
2
3
4
5
7
8
9
10
2,
• Starts playback. (VCR, DVD, BD)
3 *
• Rewinds the tape and allows picture search. (VCR)
• Hold down to go in reverse. (DVD, BD)
4+
• Stops the tape transport. (VCR)
• Playback stops when pressed. With some DVD/Blu-ray
disc players, pressing the button twice may open the disc
tray. (DVD, BD)
6
5.
• Pressing quickly once takes you to the start of the chapter
currently playing. Each time you press it, you move back
to the start of the previous chapter. (DVD, BD)
11
12
13
6 0–9, • (DOT) (STB)
• Press a button (or buttons) that corresponds to the
channel that you wish to watch.
7• Rapidly advances the tape and allows picture search.
(VCR)
• Hold down to fast forward. (DVD, BD)
8)
• Sets pauses and still pictures. (VCR, DVD, BD)
9/
14
• Pressing quickly once takes you to the start of the next
chapter. Each time you press it, you move ahead to the
start of the next chapter. (DVD, BD)
10
Presetting manufacturer codes
1 Press an appropriate button (STB, DVD•VCR or
AUDIO) to operate the connected equipment.
2 Press an appropriate button (STB, DVD•VCR or
AUDIO) and DISPLAY at the same time to enter
the code registration mode.
3 Press 0–9 to enter the manufacturer code. (See
page 51.)
• Preset mode is finished once the LED no longer lights
up.
4 After registering the code, the LED will stop blinking
then turn off after one second. (If you perform an
incorrect operation, the LED will blink quickly then
turn off.)
(REC
• Starts recording. (VCR)
11 FLASHBACK
• Press to switch between the current channel and the
channel you were watching immediately before. Some
manufacturers do not preset FLASHBACK. (STB)
12 CHU/V
• Press CHU or CHV to tune in to a higher or lower
channel. (STB)
• Press to select the channel of the TV tuner on the VCR.
(VCR)
13 MENU
• When this button is pressed, the DVD/BD menu will
display. (DVD, BD)
14 a/b/c/d, ENTER
• a/b/c/d: Press the button to select items on the STB
GUIDE screen or STB MENU screen. (STB)
Press the button to select items on the DVD/BD menu
screen. (DVD, BD)
• ENTER: Press to activate the selected function. (STB,
DVD, BD)
50
LC-40_46_52_60LE830U_E_04.indd 50
2011/01/14 22:37:52
Other Viewing Options
Manufacturer codes
VCR BRAND
AUDIO DYNAMICS
BROCKSONIC
CANON
CRAIG
CURTIS MATHIS
DBX
EMERSON
GE
INSTANT REOLYA
JC PENNEY
JVC
KENWOOD
MAGNAVOX
MAGNIN
MEMOREX
MONTGOMERY WARD
NEC
PANASONIC
PENTAX
PHILCO
PHILIPS
QUASAR
REALISTIC
SAMSUNG
SHARP
SONY
SYLVANIA
TATUNG
TEAC
TMK
YAMAHA
DVD/BD/LD BRAND
DENON
JVC
KENWOOD
MAGNAVOX
MARANTZ
MITSUBISHI
PANASONIC
PHILIPS
PIONEER
PROSCAN
RCA
SAMSUNG
SHARP
SONY
TOSHIBA
YAMAHA
ZENITH
REMOTE CONTROL CODE
NUMBER
09
13
04
12
04
09
10, 13, 14
04
04
04
09, 16, 17, 22
09
04, 05, 06
12
04
02
09
04, 18, 19, 20, 21
05
04, 05
04, 05, 06
04
01, 02
11, 12
01, 02, 03
07, 08, 15
04, 05, 06
09
09
10
09
STB BRAND
ANVISION
CABLE STAR
EAGLE
G.INSTRUMENT
GERROLD
JERROLD
MAGNAVOX
MOTOROLA
OKA SIGMA
PANASONIC
PHILIPS
PIONEER
RANDTEK
RCA
S.ATLANTA
VIEWSTAR
ZENITH
REMOTE CONTROL CODE
NUMBER
04, 05
04, 05
05
02, 03, 10, 11, 17, 20
17
02, 03, 10, 11, 12, 20,
25-34
04, 05, 08, 12, 15, 16,
18, 19, 22, 23
38
07
14, 21
04, 05, 08, 13, 15, 16,
18, 19, 22, 23
07
04, 05
14, 36*, 37*
01, 09, 24
04, 05, 08, 13, 15, 16,
18, 19, 22, 23
06, 35
• Numbers marked with * are SAT codes, all others are STB
codes.
AUDIO BRAND
SHARP
SHARP (SOUND BAR)
REMOTE CONTROL CODE
NUMBER
01
02
REMOTE CONTROL CODE
NUMBER
24
31
36
26
26
28
24, 37
26, 38
30, 33, 35
25
25, 39
29, 34
23, 32, 41, 42
27, 40
26
24
26
• Depending on the brand, the codes of some BD players
may not be supported.
51
LC-40_46_52_60LE830U_E.indb 51
2011/01/06 17:22:31
Using AQUOS LINK
Controlling HDMI Equipment Using AQUOS LINK
What’s AQUOS LINK?
• Using the HDMI CEC (Consumer Electronics Control) protocol, with AQUOS LINK you can interactively operate
compatible system equipment (Blu-ray disc equipment, AV amplifier, DVD).
• By connecting AQUOS LINK-compatible devices with HDMI-certified cables to the TV, you can control a
recorder or AV amplifier using the remote control of the TV.
• AQUOS LINK allows you to operate the HDMI-connected equipment with one remote control.
Example
Connecting AQUOS
BD Player via AQUOS
LINK-compatible
Audio system
HDMI-certified cable *
* Use HDMI 1 to connect
ARC-compatible equipment.
HDMI-certified cable
AQUOS BD Player
•
•
•
•
•
Optical fiber cable
AQUOS LINK-compatible
Audio system
Back panel
horizontal inputs
Back panel
vertical inputs
For connecting the TV to AQUOS LINK-compatible equipment, use commercially available cables.
Point the remote control toward the TV, not to connected HDMI equipment.
Video noise may occur depending on the type of HDMI cable used. Make sure to use an HDMI-certified cable.
Up to 3 pieces of HDMI recording equipment and one AV amplifier can be connected using this system.
These operations affect the HDMI equipment selected as the current input source. If the equipment does not operate, turn on
the equipment and select the appropriate input source using INPUT.
Connected AQUOS LINK-compatible devices can be operated without
changing the settings of the remote control unit.
OPTION button will function only when AQUOS LINK is used.
■ One Touch Play
While the TV is in standby mode, it automatically turns on and plays back the
image from the HDMI source.
■ One Touch Recording
Press EREC while you are viewing a broadcast received with the AQUOS
LINK-compatible recorder. The AQUOS LINK automatically recognizes the
connected HDMI device and starts recording.
■ Single remote control
The AQUOS LINK automatically recognizes the connected HDMI device and
you can control the TV and the devices as if using a universal remote control.
■ Control the AQUOS LINK-compatible audio system
Set the volume of AQUOS LINK-compatible audio system.
• The above description is an example of the AQUOS LINK function.
• The steps in “AQUOS LINK Setup” on page 53 need to be completed beforehand.
• Refer to this operation manual and the operation manual of the AQUOS LINK device to be used with this TV.
52
LC-40_46_52_60LE830U_E.indb 52
2011/01/06 17:22:31
Using AQUOS LINK
AQUOS LINK Setup
Example
System
Options
Menu
System Options
AQUOS LINK Setup
AQUOS LINK Control
[On]
Auto Power On
[Yes]
Selecting Recorder
Channel Select Key
Audio Return Channel
[Auto]
1 Press MENU to display the MENU screen, and then
press c/d to select "System Options".
2 Press a/b to select “AQUOS LINK Setup”, and
then press ENTER.
3 Press a/b to select a specific item, and then press
Channel Select Key
This function can be set for each input terminal.
On: The remote control unit of the TV can be used to
select the channel, display program information, and
perform other operations of a connected AQUOS
LINK-compatible recorder.
Off: This function does not work.
Audio Return Channel
This function allows you to listen to the TV audio via
audio equipment without using an optical fiber cable,
which conventionally is required.
Requirements for using an ARC-compatible AV
amplifier:
• ARC-compatible AV amplifier connected to the ARCcompatible HDMI terminal (HDMI 1).
(Refer to the operation manual of the ARC-compatible
equipment for details.)
• Use of an ARC-compatible cable.
Auto: You can listen to the TV audio with ARCcompatible audio equipment.
Off: This function does not work.
ENTER.
4 Press a/b (or c/d ) to select the desired setting,
and then press ENTER.
5 Press MENU to exit.
• If the TV audio cannot be output from the AV amplifier even
after making the necessary settings, connect the TV to the
AV amplifier with an optical fiber cable and select “Off”.
One Touch Playback
AQUOS LINK Control
Select AQUOS LINK Control to disable AQUOS LINK
function even when an AQUOS LINK-compatible HDMI
device is connected to the TV. This function prevents
the device from starting to operate unexpectedly.
On: You can operate AQUOS LINK-compatible
equipment.
Off: AQUOS LINK function does not work.
Auto Power On
If this is activated, the One Touch Play function is
enabled.
Yes: While the TV is in standby mode, it automatically
turns on and plays back the image from the HDMI
source.
No: This function does not work.
AQUOS LINK allows you to operate the HDMIconnected equipment with one remote control.
Press d to start playing back a title.
• The last played program is played back. You can use the
following buttons during broadcast viewing.
Buttons
Selecting Recorder
When multiple AQUOS LINK-compatible devices are
connected, this function allows you to set the recorder
for recording when you press EREC on the TV’s
remote control unit.
Press a/b to select the recorder for recording.
• When an AQUOS LINK-compatible audio system or other
equipment is connected between the TV and recorder,
“Sub” is displayed.
POWER
(SOURCE)
G
I
J
Description
Turns the power of the HDMI connected devices
on and off.
Hold down to go in reverse.
Starts playback.
Hold down to fast forward.
H
Playback stops.
F
Sets pauses and still pictures.
T
Pressing quickly once takes you to the start of the
chapter currently playing. Each time you press it,
you move back to the start of the previous chapter.
U
Pressing quickly once takes you to the start of the
next chapter. Each time you press it, you move
ahead to the start of the next chapter.
• The buttons T/U do not function with the following
Blu-ray disc players currently available.
- BD-HP20U, BD-HP50U
53
LC-40_46_52_60LE830U_E.indb 53
2011/01/06 17:22:31
Using AQUOS LINK
Link Operation Menu
Menu
Link
Operation
Link Operation
Link
Operation
Menu
Link Operation
Recorder Power On/Off
Start Recording
Device Operation panel
Stop Recording
Play from Rec. List
One Touch Recording
This function allows easy one-touch recording of the
program being viewed on the TV to AQUOS LINKcompatible equipment with a recording function by
simply pressing EREC on the remote control.
Prepare the connected AQUOS LINK-compatible
recorder for recording. Check the following items.
• Make sure that the antenna cable is connected.
• Check that there is sufficient available space on the
recording media (HDD, DVD, etc.).
• On the TV, use “AQUOS LINK Setup” and “Selecting
Recorder” to select the equipment for recording.
• By default, the recorder connected to HDMI 1 is selected
for recording.
Show Start Menu
Change Media of Device
Link Booking (Rec. Book)
Change Audio Output Device
[By AQUOS SP]
Change Surround Mode
HDMI Device Selection
AQUOS LINK Setup
1 Press EREC to start recording.
• When you are viewing a broadcast received with the
AQUOS LINK-compatible recorder selected in "Selecting
Recorder", recording to the AQUOS recorder of the
broadcast being viewed starts.
• When you are viewing a broadcast received with
equipment other than the AQUOS LINK-compatible
recorder selected in "Selecting Recorder" or other
external input equipment, pressing EREC on the remote
control does not start recording.
2 Use the Link Operation Menu to stop recording.
1 Press OPTION to display the Link Operation
Menu screen.
2 Press a/b to select “Stop Recording”, and
then press ENTER.
Start/Stop Recording
You can also use the Link Operation Menu for
recording on the connected AQUOS LINK-compatible
equipment.
1 Press OPTION to display the Link Operation Menu
screen.
2 Select “Start Recording”, and then press ENTER to
start recording.
• You can also start recording by pressing
remote control unit.
EREC
on the
3 Select “Stop Recording”, and then press ENTER to
stop recording.
Displaying the Link Operation Menu
1 Press OPTION to display the Link Operation Menu
screen.
2 Press a/b to select “AQUOS LINK Setup”, and
then press ENTER.
• The AQUOS LINK Setup menu screen is displayed.
Turning On/Off AQUOS LINK-compatible
Equipment
You can manually turn on/off the power of connected
AQUOS LINK-compatible equipment.
1 Press OPTION to display the Link Operation Menu
screen.
2 Press a/b to select “Recorder Power On/Off”, and
then press ENTER.
3 Select “On” (or “Off”) and press ENTER to turn on
(or off) the equipment.
54
LC-40_46_52_60LE830U_E.indb 54
2011/01/06 17:22:31
Using AQUOS LINK
Using the Device Operation Panel
You can use the device operation panel to control
playback operations.
1 Press OPTION to display the Link Operation Menu
screen.
2 Press a/b to select “Device Operation Panel”, and
then press ENTER.
3 Press a/b/c/d to select the desired operation.
• This function works only when AQUOS LINK-compatible
equipment with the Device Operation Panel function is
connected.
Playback of Titles Using AQUOS LINK
This section explains how to play back a title in the
AQUOS LINK-compatible equipment.
Timer Recording
You can call up the AQUOS LINK-compatible
recorder’s EPG and preset timer recordings using the
TV’s remote control.
1 Press OPTION to display the Link Operation Menu
screen.
2 Press a/b to select “Link Booking (Rec. Book)”,
and then press ENTER.
• The recorder’s EPG is displayed.
3 Select the program to record.
• You can use a/b/c/d, ENTER, RETURN, EXIT and
the colored buttons.
• This function works only when an AQUOS LINK-compatible
recorder is connected.
• Refer to the operation manual of the recorder for details.
1 Power on the AQUOS LINK-compatible equipment,
Listening with the AQUOS AUDIO Speaker System
2 Press OPTION to display the Link Operation Menu
You can select to listen to the TV sound only from the
AQUOS LINK-compatible audio system and manually
change its sound mode.
and select appropriate external input.
screen.
3 Press a/b to select “Play from Rec. List”, and
then press ENTER.
• The title list data from the connected AQUOS LINKcompatible equipment displays.
4 Select the title with a/b/c/d, and then press d
to start playback.
• This function works only when AQUOS LINK-compatible
equipment is connected.
Displaying the Setup Menu of AQUOS
LINK-Compatible Equipment
You can call up a setup menu from the connected
AQUOS LINK-compatible equipment.
1 Press OPTION to display the Link Operation Menu
screen.
2 Press a/b to select "Show Start Menu", and then
press ENTER.
• The setup menu of the AQUOS LINK-compatible
equipment is displayed.
• Depending on the status of the equipment (recording or in
standby mode, etc), the setup menu will not be displayed.
• The setup menu will not be displayed with the player
BD-HP20U currently available.
Selecting Media Type for AQUOS LINKCompatible Recorder
You can switch the media (HDD or DVD) for playback
or recording on the AQUOS LINK-compatible recorder.
1 Press OPTION to display the Link Operation Menu
screen.
2 Press a/b to select “Change Media of Device”,
and then press ENTER.
1 Press OPTION to display the Link Operation Menu
screen.
2 Press a/b to select “Change Audio Output
Device”, and then press ENTER.
3 Press a/b to select “By AQUOS audio SP”, and
then press ENTER.
• The sound from the TV speaker is muted and only the
sound from the AQUOS LINK-compatible audio system
is audible.
• You can use VOLk/l and MUTE.
Select “By AQUOS SP”, and then press ENTER to
listen to the TV sound.
Manually Changing AQUOS AUDIO Speaker
System’s Sound Mode
1 Press OPTION to display the Link Operation Menu
screen.
2 Press a/b to select “Change Surround Mode”,
and then press ENTER.
• The sound mode changes each time you press ENTER.
• Refer to the operation manual of the AQUOS LINKcompatible audio system for details.
HDMI Device Selection
If multiple HDMI devices are connected in a daisy
chain, you can specify which device to control here.
1 Press OPTION to display the Link Operation Menu
screen.
2 Press a/b to select “HDMI Device Selection”, and
then press ENTER.
• A list of connected HDMI devices is displayed.
3 Press a/b to select the desired device, and then
press ENTER.
3 Select the desired media such as HDD or DVD.
• The Media type toggles each time you press ENTER in
“Change Media of Device”.
• Select the media to be operated by the player.
55
LC-40_46_52_60LE830U_E_05.indd 55
2011/01/17 20:51:22
Using a PC
Displaying a PC Image on the Screen
VIEW MODE
You can select the screen size.
1 Press VIEW MODE.
• The View Mode menu displays.
• The menu lists the View Mode options selectable for the type of video signal currently
being received.
2 Press VIEW MODE or a/b while the View Mode menu is displayed to select a
desired item on the menu.
• You can sequentially select a View Mode that has its own aspect ratio.
• Connect the PC before making adjustments. (See page 17.)
• Selectable screen size may vary with input signal type.
• You can have the same settings by choosing "View Mode" on the menu items. (See page 31.)
Example: Screen size images
Input signal
4:3
Normal
Keeps the original
aspect ratio in a full
screen display.
Zoom
For viewing
widescreen
programs. The top
and bottom of the
image is cropped.
Input signal
Stretch
Dot by Dot
16:9
An image fully fills the
screen.
Detects the resolution
of the signal and
displays an image with
the same number of
pixels on the screen.
Stretch
Dot by Dot
An image fully fills the
screen.
Detects the resolution
of the signal and
displays an image with
the same number of
pixels on the screen.
56
LC-40_46_52_60LE830U_E.indb 56
2011/01/06 17:22:31
Using a PC
Example
Menu
System
Options
Audio Select
System Options
View Option
AQUOS LINK Setup
Input Terminal Setting
Menu Design
O
1
2
3
4
5
ti
L
Setting Audio Input
kO t
Press MENU to display the MENU screen, and then
press c/d to select "System Options".
Press a/b to select "Input Terminal Setting", and
then press ENTER.
Press a/b to select "PC input" or "Audio Select",
and then press ENTER.
Press a/b to select a specific adjustment item,
and then press ENTER to set each item.
Press a/b (or c/d) to select or adjust the desired
setting, and then press ENTER.
Adjusting the PC Image
Auto Sync. (for Analog PC Input Mode Only)
For automatically adjusting the PC image.
Yes: Auto Sync. starts and "Now adjusting the image."
displays.
No: This function does not work.
• When "Auto Sync." is successful, "Completed" displays. If
not, "Auto Sync." failed.
• "Auto Sync." may fail even if "Completed" displays.
• "Auto Sync." may fail if the computer image has low
resolution, has unclear (black) edges, or is moved while
executing "Auto Sync.".
• Be sure to connect the PC to the TV and switch it on before
starting "Auto Sync.".
Fine Sync.
Ordinarily you can easily adjust the picture as necessary
to change image position using "Auto Sync.". In some
cases, however, manual adjustment is needed to
optimize the image.
H-Pos.: Centers the image by moving it to the left or right.
V-Pos.: Centers the image by moving it up or down.
Clock: Adjust when the image flickers with vertical
stripes.
Phase: Adjust when characters have low contrast or
when the image flickers.
• For resetting all "Fine Sync." adjustment items to the factory
preset values, press a/b to select "Reset", and then press
ENTER.
• It is not necessary to adjust the "Clock" or "Phase" when a
digital signal is being input, so it cannot be selected.
• The default cursor position may not be in the center,
because the screen position variable ranges may be
asymmetrical.
• The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
position-setting screen.
This function sets the terminal to output the computer
audio.
The adjustment items vary depending on the input
source. Select the input source corresponding to the
terminal connected to the PC and then adjust the
desired item.
■ PC IN
Video: Select this when the TV and PC are connected
using an analog RGB cable and the audio is not input.
Video+Audio: Select this when the TV and PC are
connected using an analog RGB cable and the audio is
input via a Ø 3.5 mm stereo minijack.
■ HDMI 1
HDMI(Digital): Select this when the TV and PC are
connected using an HDMI-certified cable and audio is
input via the same cable.
HDMI+Analog: Select this when the TV and PC are
connected using a DVI-HDMI conversion cable and the
audio is input via a Ø 3.5 mm stereo minijack.
• When "Audio Select" is set to "HDMI(Digital)", sound will
not be produced if you use only an HDMI-certified cable to
connect HDMI-compatible equipment. To produce sound,
you should make an analog audio connection.
• If you want to connect HDMI-compatible equipment
using only an HDMI-certified cable, set "Audio Select" to
"HDMI(Digital)".
PC Compatibility Chart
It is necessary to set the PC correctly to display XGA
and WXGA signal.
Resolution
720 x 400
VGA
640 x 480
SVGA
800 x 600
XGA
1024 x 768
WXGA
SXGA
SXGA+
UXGA
1080p
1360 x 768
1280 x 1024
1400 x 1050
1600 x 1200
1920 x 1080
Horizontal Vertical
VESA
Frequency Frequency Standard
31.5 kHz
31.5 kHz
37.9 kHz
37.5 kHz
35.1 kHz
37.9 kHz
48.1 kHz
46.9 kHz
48.4 kHz
56.5 kHz
60.0 kHz
47.7 kHz
64.0 kHz
65.3 kHz
75.0 kHz
67.5 kHz
70 Hz
60 Hz
72 Hz
75 Hz
56 Hz
60 Hz
72 Hz
75 Hz
60 Hz
70 Hz
75 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
O
O
O
O
O
O
O
O
O
O
O
O
O
O
VGA and XGA are registered trademarks of International
Business Machines Corp.
57
LC-40_46_52_60LE830U_E.indb 57
2011/01/06 17:22:32
Using a PC
Control of the TV
• The TV can be controlled from a PC, control panels
and other devices using the RS-232C or IP.
• Use a cross-type RS-232C cable, ETHERNET cable
(commercially available) or wireless LAN for the
connections.
• This operation system should be used by a person who is
accustomed to using computers.
■ Communication conditions for IP
Connect to the TV with the following settings made for
IP on the PC.
IP protocol:
Host IP address:
Service:
TCP port#:
TCP/IP
Set the IP address on the TV menu
None (Do not select Telnet or SSH)
Set a port number on the TV menu
(Control port)
When you set your ID and password on the TV menu,
you need to enter them as soon as you connect to the
TV.
• The connection will be cut off when there has been no
communication for 3 minutes.
IP Control Setup
Menu
EZ Setup
Broadcasting Setup
Internet Setup
[English]
DivX ® Setup
1 Press MENU to display the MENU screen, and then
4
9,600 bps
8 bits
None
1 bit
None
■ Communication procedure
Send the control commands from the PC via the RS232C or IP.
The TV operates according to the received command
and sends a response message to the PC.
Do not send multiple commands at the same time.
Wait until the PC receives the OK response before
sending the next command.
■ Command format
Eight ASCII codes e CR
C1 C2 C3 C4 P1 P2 P3
Command 4-digits
P4
Parameter 4-digits
Return code
■ Parameter
0
Language
3
Baud rate:
Data length:
Parity bit:
Stop bit:
Flow control:
Input the parameter values, aligning left, and fill with
blank(s) for the remainder. (Be sure that 4 values are
input for the parameter.)
When the input parameter is not within an adjustable
range, “ERR” returns. (Refer to “Response code format”.)
Any numerical value can replace the “x” on the table.
Initial Setup
2
Set the RS-232C communication settings on the PC to
match the TV's communication conditions.
The TV's communication settings are as follows:
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter 0–9, x, blank, ?
Example
Initial
Setup
■ Communication conditions for RS-232C
press c/d to select "Initial Setup".
Press a/b to select "Internet Setup", and then
press ENTER.
Press a/b to select "Network Setup", and then
press ENTER.
Press a/b to select "IP Control Setup", and then
press ENTER.
0
0
0
a
3
0
9
When “?” is input for some
commands, the
?
present setting
value responds.
?
?
?
?
■ Response code format
Normal response
O
K
Problem response (communication
error or incorrect command)
E
Return code (0DH)
R
R
Return code (0DH)
5 Press c/d to select "Change", and then press
ENTER.
6
To use IP Control, press c/d to select "Enable",
and then press ENTER.
7 Set the device name.
8 Set your login ID and password.
9 Set the port to use with IP Control.
10 Confirm the settings, and then press "OK".
58
LC-40_46_52_60LE830U_E.indb 58
2011/01/06 17:22:32
Using a PC
■ Command table
• Commands not indicated here are not guaranteed to operate.
CONTROL CONTENTS
The Power On command rejected.
The Power On command accepted.
The Power On command accepted.
When the power is in standby mode, commands also go to waiting status
and so power consumption is just about the same as usual. With the
commands in waiting status, the Center Icon Illumination on the front of the
TV lights up.
It shifts to standby.
Power On
It input-switches by the toggle. (It is the same as an input change key)
It input-switches to TV. (A channel remains as it is. (Last memory))
CONTROL ITEM
POWER ON COMMAND SETTING
COMMAND PARAMETER
R S P W 0 _ _ _ Off
1 _ _ _ On [RS-232C]
2 _ _ _ On [IP]
POWER SETTING
P O W R 0
1
I T G D x
I T V D 0
I A V D *
_
_
_
_
_
_
_
_
_
_
A V M D
*
_
_
VIEW MODE
V
H
V
C
P
W
*
*
*
*
*
*
*
*
*
*
*
_
_
*
*
*
*
_
1: HDMI 1, 2: HDMI 2, 3: HDMI 3, 4: HDMI 4,
5: COMPONENT, 6: VIDEO 1, 7: VIDEO 2
_ 0: (Toggle), 1: STANDARD, 2: MOVIE , 3: GAME,
4: USER, 5: DYNAMIC (Fixed), 6: DYNAMIC, 7: PC,
8: x.v. Color, 100: AUTO
_ Volume (0–60)
_
_
_ Only PC mode. (0–180)
_ Only PC mode. (0–40)
_ 0: (Toggle) [AV], 1: Side Bar [AV], 2: S.Stretch [AV]
3: Zoom [AV], 4: Stretch [AV], 5: Normal [PC]
6: Zoom [PC], 7: Stretch [PC],
8: Dot by Dot [PC] [AV], 9: Full Screen [AV]
10: Auto [USB-Video, DLNA-Video or Internet applications],
11: Original [USB-Video, DLNA-Video or Internet applications]
MUTE
SURROUND
AUDIO SELECTION
SLEEP TIMER
M U T E *
A C S U *
A C H A x
O F T M *
_
_
_
_
_
_
_
_
_
_
_
_
D C C H
*
*
*
D A 2 P
D C 2 U
*
*
*
*
*
*
* (0100-9999)
_ (1-999)
D C 2 L
*
*
*
_ (0-999)
D
D
C
C
C
T
M
S
*
*
x
x
x
1
1
1
*
*
_
_
_
_
_
_
*
*
_
_
_
_
_
_
*
*
_
_
_
_
_
_
P P V 1
_
_
_
INPUT SELECTION
TOGGLE
TV
1-7
AV MODE SELECTION
VOLUME
POSITION
CHANNEL
H-POSITION
V-POSITION
CLOCK
PHASE
DIRECT
CHANNEL
(ANALOG)
DIRECT
CHANNEL
(DIGITAL)
CH UP
CH DOWN
CC
DEVICE NAME
MODEL NAME
SOFTWARE VERSION
IP PROTOCOL VERSION
I
O
P
P
L
H
I
C
C
H
H
L
V
N
W
L
O
O
C
S
D
1
1
U
D
C
N
R
V
M
S
S
K
E
E
0
1
P
W
P
M
D
N
_
_
_
_
_
Power Off
Power On
(Toggle)
0: (Toggle), 1: On, 2: Off
0: (Toggle), 1: On, 2: Off
(Toggle)
0: Off, 1: OFF TIMER – 30 MIN., 2: OFF TIMER – 60 MIN.,
3: OFF TIMER – 90 MIN., 4: OFF TIMER – 120 MIN.
_ The channel number of TV
(1–135)
(0-9999)
(0-6383)
The channel number of TV +1
The channel number of TV –1
(Toggle)
Although it can choose now, it is toggle operation in inside.
The screen position variable ranges depend on the View Mode or the
signal type. The ranges can be seen on the position-setting screen.
0: Although it can choose now, it is toggle operation in inside.
1: Only available when 4:3 signal is being input.
5, 6: Only available when 4:3 signal is being input.
8: [PC] Available except when UXGA is being input.
[AV] Only available when 1080i/p is being input.
9: Only available when 720p is being input.
10, 11: Available when USB-Video, DLNA-Video or Internet application is used.
An input change is included if it is not TV display.
In Air, 2–69ch is effective.
In Cable, 1–135ch is effective.
DIGITAL Air (Two-Part numbers, 2-digit plus 2-digit)
DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)
Front half of DIGITAL CABLE CHANNEL NO. (Designate major channel)
DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)
Rear half of DIGITAL CABLE CHANNEL NO. (Designate minor channel)
DIGITAL Cable (One-Part numbers, 5-digit, less than 10,000)
DIGITAL Cable (One-Part numbers, 5-digit, more than 10,000)
If it is not TV display, it will input-switch to TV. (same function as CHU)
If it is not TV display, it will input-switch to TV. (same function as CHV)
Toggle operation of a closed caption.
The device name set in "IP Control Setup" is displayed.
The model name of the TV
The current version of the TV software is displayed.
The currently supported version of IP protocol is displayed.
• If an underbar (_) appears in the parameter column, enter a space.
• If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.
• Any numerical value can replace the “x” on the table.
59
LC-40_46_52_60LE830U_E.indb 59
2011/01/06 17:22:32
Using the Internet
By connecting your TV to a broadband system, you can access the Internet from the TV.
• Display the latest Internet information and access a range of useful information for AQUOS users from the
original home page*.
• Use "AQUOS ADVANTAGE LIVE" to obtain the latest software and receive online user support.
• You can enjoy a variety of streaming content and Internet applications.
* About the original home page
• The original home page is a website set up specifically for AQUOS owners.
• The website is worth visiting as it provides a range of useful information, including tips on using your AQUOS
and a frequently asked questions section.
Connecting to the Internet
• To connect your TV to the Internet, you must have a broadband Internet connection.
• If you do not have a broadband Internet connection, consult the store where you purchased your TV or ask your
Internet service provider or telephone company.
• When an Internet connection is made, an Ethernet and wireless connection cannot be used at the same time.
Use only one of the connection types. (See page 62.)
H Using an ETHERNET cable
Use an ETHERNET cable (commercially available) to connect the ETHERNET terminal on the TV to your broadband
router (commercially available).
ETHERNET cable
LAN
PC
Broadband router
Modem
Internet
60
LC-40_46_52_60LE830U_E.indb 60
2011/01/06 17:22:32
Using the Internet
H Using the wireless LAN
This TV is equipped with a wireless LAN function.
For a wireless LAN connection, you must use "Wireless Setup" to connect the access point and TV. (See page 62.)
PC
Wireless LAN router/
access point
Modem
Internet
• This TV has a built-in wireless LAN function. Using a separate wireless USB LAN adapter may result in radio communications
that do not comply with regulations on radio communications. Therefore, do not use a separate wireless LAN adapter.
• This TV has received the following certifications.
- Wi-Fi CERTIFIED™ (certification program from the Wi-Fi Alliance® )
- Wi-Fi Protected Setup™ (certification program from the Wi-Fi Alliance® )
• Operations cannot be guaranteed when used with access points that do not have Wi-Fi® certification.
• A wireless LAN router/access point is required to connect the TV to the Internet using a wireless LAN. See the operation
manual of your access point for setup.
• If your access point is set to a stealth mode (that prevents detection by other devices), you may not be able to establish a
connection. In this case, disable the stealth mode on the access point.
• A wireless LAN connection and performance cannot be guaranteed for all residential environments. In the following cases, the
wireless LAN signal may be poor or drop, or the connection speed may become slower.
- When used in buildings made with concrete, reinforced steel, or metal
- When placed near objects that obstruct the signal
- When used with other wireless devices that emit the same frequency
- When used in the vicinity of microwave ovens and other devices that emit a magnetic field, electrostatic charge, or
electromagnetic interference
• When there is significant interference in the 2.4-GHz frequency (such as from other wireless LAN devices, Bluetooth® devices,
2.4-GHz cordless telephones, and microwave ovens), it is recommended that you use a wireless LAN router/access point that
supports IEEE802.11a/n (5 GHz) and set the access point to transmit at 5 GHz. For setup details, see the operation manual of
your access point.
• For users outside the United States, be sure to select your country before using the wireless LAN function. (See page 63.)
• A stable connection speed is required to play back streaming content. Use an Ethernet connection if the wireless LAN speed
is unstable.
• Before transferring to a third party or disposal, be sure to initialize the wireless LAN settings.
• Please follow the legislation in your country when using the wireless LAN outdoors.
61
LC-40_46_52_60LE830U_E.indb 61
2011/01/06 17:22:32
Using the Internet
Internet Setup
Example
Initial
Setup
Menu
5 Press a/b to select "Push button", and then press
ENTER.
• To configure the setting via PC, select "PIN code".
Follow the on-screen instructions and the operation
manual of the access point to configure the settings.
6 Select "Next" to complete the settings.
• The connection process starts and the WPS button on
the access point can be pressed.
Initial Setup
7 Press the WPS button on the access point.
EZ Setup
• Pressing the WPS button displays a confirmation
screen. Please wait until a connection is established.
Broadcasting Setup
8 When a connection is established, the connection
Internet Setup
details are displayed. Press ENTER.
Language
[English]
DivX ® Setup
Connection Type
1 Press MENU to display the MENU screen, and then
2
3
4
press c/d to select "Initial Setup".
Press a/b to select "Internet Setup", and then
press ENTER.
Press a/b to select "Network Setup", and then
press ENTER.
Press a/b to select "Connection Type", and then
press ENTER.
5 Press c/d to select "Wired" or "Wireless", and
then press ENTER.
• If you select "Wired", the signal is detected and setup
is performed automatically. Use "IP Setup" to check
and change the settings as necessary. (See page 63.)
• If you select "Wireless", use "Wireless Setup" to
configure the access point settings.
Wireless Setup
If your access point supports Wi-Fi Protected Setup
(WPS), it is recommended that you use this function
for the wireless connection. You can press the WPS
button on the access point to configure the settings
automatically.
• The name of the WPS button function may differ depending
on the access point. See the operation manual of the
access point for details.
1 Confirm the current settings in "Connection Type".
• If "Wired" is selected, press c/d to select "Wireless".
2 Press a/b to select "Wireless Setup", and then
press ENTER.
• Confirm the settings. If each setting item is correct,
press MENU to exit.
• If you are configuring the wireless setup for the first
time or changing the settings, go to step 3.
3 Press c/d to select "Change", and then press
4
ENTER.
Press a/b to select "WPS", and then press
ENTER.
Interactive Service
If you do not want other people to connect to the
Internet in your absence, you can make settings to
keep the TV away from the Internet.
1 Press MENU to display the MENU screen, and then
press c/d to select “Initial Setup”.
2 Press a/b to select “Internet Setup”, and then
press ENTER.
3 Press a/b to select “Interactive Service”, and then
press ENTER.
• Input the 4-digit secret number by using 0-9.
4 Press c/d to select “No”, and then press ENTER.
• If you want to allow Internet connection, select “Yes”,
and then press ENTER.
5 Press MENU to exit.
Checking Your Internet Connection
Press AQUOS NET once or twice to switch to the
TV+Web or Web screen.
• If "
" is displayed after you connect to the Internet,
check your TV's network settings and connection.
• When the original home page appears, now you are
connected to the Internet.
• You can also display the AQUOS NET screen by pressing
FAV APP on the remote control unit. See page 35 for
details on the FAV APP key Assign function.
• If you have failed to connect to the Internet in the above
operation, then an error message will appear. In this case,
press EXIT to return to the normal TV screen and check
the relevant settings (see page 63).
• If you still cannot connect to the Internet, please consult
your Internet service provider or telephone company.
• When an application is used, you cannot make adjustments
for "Internet Setup".
If you need to make the settings of "Internet Setup", press
EXIT to return to the normal TV screen.
• To select and register an access point manually, select
"Search" or "Manual Setup" and make the necessary
settings.
62
LC-40_46_52_60LE830U_E_06.indd 62
2011/01/26 22:11:13
Using the Internet
Displaying Updated Information and
Support Service
This function can be used to display up-to-date
information on the original home page and allow you to
receive support service over the network.
Original Home Page
H If you cannot connect to the Internet
Perform the procedures below to check your TV's
network settings.
IP Setup
1 Press EXIT to display the normal TV screen.
2 Press MENU to display the MENU screen, and then
3
4
5
press c/d to select “Initial Setup”.
Press a/b to select “Internet Setup”, and then
press ENTER.
Press a/b to select “Network Setup”, and then
press ENTER.
Press a/b to select “IP Setup”, and then press
ENTER.
• Check that numbers are displayed for each setting.
• If there are any settings without numbers, specify the
numbers by following the on-screen instructions.
• For information on how to enter text, see page 64.
Example
Setting IP information
[Current Setup]
IP Address
Netmask
Gateway
DNS
Proxy
MAC Address
:
:
:
:
:
:
Auto Setup
Auto Setup
Auto Setup
Auto Setup
No Use
XX:XX:XX:XX:XX:XX
Change
Initialize
6 Press MENU to exit.
Setting the Country
1 Repeat steps 1 to 4 in IP Setup.
2 Press a/b to select "Country", and then press
3
1 Press AQUOS NET once or twice.
• You can also display the original home page by
pressing FAV APP on the remote control unit. See
page 35 for details on the FAV APP key Assign
function.
• Each time you press AQUOS NET, the screen image
toggles as shown below:
TV+Web
Web
TV
• When you are not connected to the Internet, a network
function explanation screen is displayed.
The services displayed vary depending on circumstances.
2 Press a/b/c/d to select a title, and then press
ENTER.
• The service details vary depending on circumstances.
3 Press EXIT to return to the normal TV screen.
• Web page appearances may differ depending on the type
of screen (TV+Web or Web).
• When displaying TV+Web with a channel in which the
V-Chip is enabled, the cursor keys on the remote control
unit do not function.
AQUOS Advantage Live
1 Press APPS to display the application window.
2 Press c/dto select “AQUOS ADVANTAGE LIVE”,
and then press ENTER.
• You can also display the AQUOS ADVANTAGE LIVE
screen by pressing FAV APP on the remote control
unit. See page 35 for details on the FAV APP Key
Assign function.
3 Press a/b/c/d to select the desired service.
4 Press EXIT to return to the normal TV screen.
• The display may change as a result of a software update.
ENTER.
Press a/b to select "US", "Canada", "Mexico" or
"Others", and then press ENTER.
• If you select “Others”, you need to set the desired area.
4 Press MENU to exit.
Setting the Zip Code
1 Repeat steps 1 to 4 in IP Setup.
2 Press a/b to select “Zip Code”, and then press
3
ENTER. After “Change” is highlighted, press
ENTER again.
Enter your zip code.
• Use 0-9 on the remote control unit, or use the software
keyboard.
4 After “Complete” is highlighted, press ENTER.
5 Press MENU to exit.
63
LC-40_46_52_60LE830U_E.indb 63
2011/01/06 17:22:33
Using the Internet
Entering Text (Software Keyboard)
When you are editing an input screen or specifying the
Ethernet settings used for accessing the Internet, enter
text from the software keyboard.
Caps Off/Caps On/Caps Lock
If “alphabet” is selected in “Character Set”, this switches
characters between uppercase and lowercase.
Each time you press ENTER, the character type switches as
shown below:
Caps Off: all the characters are lowercased
Caps On: only the first character is uppercased
Caps Lock: all the characters are uppercased
• You can enter up to 128 characters for text.
The text you enter is displayed as you type it in.
To move the cursor (the current input position), use
” or “
” on the software keyboard.
“
Press c/d to select the type of characters entered:
alphabet, number or sign.
(The selectable types depend on the input source.)
Done
Applies the entered information and closes the software
keyboard.
Quit
Closes the software keyboard without applying the entered
information.
• You can also close the software keyboard by pressing
EXIT on the remote control unit.
Displays the icon “
inserted.
”, indicating that a new line has been
Clear
Erases the character string.
• When the cursor is somewhere in a line: the character
string to the right of the cursor will be erased.
• When the cursor is at the right end of a line: the entire line
will be erased.
Enters a space.
Delete
If the cursor is at the right end of a line, this erases text one
character at a time.
• You can also delete text by pressing RETURN on the
remote control unit.
While you are entering text, likely input conversion candidates
are displayed based on what you typed in.
• You can also enter text by pressing A, B or C on the remote
control unit.
Buttons
a
b
c
d
ENTER
EXIT
RETURN
0-9
A (red)
B (green)
C (blue)
D (yellow)
Description
Moves the focus up. When the focus is at the top edge, this moves the focus to
the opposite edge (bottom edge).
Moves the focus down. When the focus is at the bottom edge, this moves the
focus to the opposite edge (top edge).
Moves the focus left. When the focus is at the left edge, this moves the focus to
the opposite edge (right edge).
When the focus is on “Character Set”, this selects the character type (moving
backwards).
When the focus is in an input box, this moves the cursor in the input box to the left.
Moves the focus right. When the focus is at the right edge, this moves the focus to
the opposite edge (left edge).
When the focus is on “Character Set”, this selects the character type (moving
forwards).
When the focus is in an input box, this moves the cursor in the input box to the
right.
Performs the processing for the button currently in the focus.
Closes the software keyboard without applying the original input elements for the
entered text.
Erases the text in the input box where the cursor is currently located.
When the cursor is at the end of a sentence, this acts as a backspace.
Directly enters the single-byte number for that button.
Directly enters prediction candidate 1.
Directly enters prediction candidate 2.
Directly enters prediction candidate 3.
Enters a space.
64
LC-40_46_52_60LE830U_E.indb 64
2011/01/06 17:22:33
Using the Internet
Using the Browser
ENTER, a/b/c/d
• Press a/b/c/d to select a link that you want to jump,
and then press ENTER.
EXIT
About links
• Web pages on the Internet often include “links” that
allow you to jump to other web pages (or sites).
• “Links” can take various forms, including words
or images, but they always work in the same way
letting you jump to the link destination when you
select them.
• Selected items (such as links of text input fields) are
enclosed in a yellow frame.
• You can jump from a “link” to the corresponding link
destination.
CAUTION
• Press the button to return to the TV screen.
RETURN
• Press the button to return to the previous page.
Example : The image shown below, which is only for
explanation, is subject to change.
AQUOS Network
What’s New
AQUOS Center
Fea
eat ured CContent
Photo Player
Entertainment
Sports
AQUOS Gallery
• If the power is cut due to a power failure or the TV being
unplugged while you are using the Internet, information
such as bookmarks or cookies may not be saved correctly.
When a security notification window is displayed:
• Press ENTER to close the window.
• This window appears when you visit a web page that has
security protection, or when you move from a protected
page to an unprotected page.
• In “Security Settings” you can set whether or not this
window is displayed. (See page 68.)
When a cookie confirmation window appears:
Choose whether or not to accept the cookie (see page 68),
and then press ENTER.
• In “Cookies” settings you can set whether or not this
window is displayed. You can also opt to delete all the
cookies at once. (See page 68.)
Monday
Tuesday
Wednesday
CONSOLE
Today
GEMINI
AQUARIUS
ARIES
PISCES
Page 1
of 3
Add Widgets
Legal
Click this but ton to go to AQUOS Network.
AQUOS Co n s ole
Tab
D :Tool
:Scroll
Pages with security protection are
clearly shown as such.
If content on a page is continued on another page,
directions to that page are shown clearly.
You can use a/b/c/d to go to the continuation of a
page.
• Where there is link text or a link image in the
direction pressed, the text or image is selected first.
If this happens, press the same direction button
several times.
To users who access the Internet from a PC
• When you access the Internet from this TV, the
procedures may not be the same as regular
browser-based access on a PC.
• You cannot download files.
• You cannot view a history of the pages you have
visited.
• You cannot change the startup page displayed
when you press AQUOS NET.
• Pop-up windows appear in separate tabs.
• On some pages, video and audio cannot be
played, and text or images may not be displayed
correctly.
When “z” is displayed in a page:
• The page failed to load successfully, or it contains images
with formats that cannot be displayed on the TV. Try
reloading the page by selecting “
” (see page 66) in the
toolbar.
65
LC-40_46_52_60LE830U_E.indb 65
2011/01/06 17:22:33
Using the Internet
Using the Toolbar
Using Tabs
You can use the toolbar to control the browser and to
specify settings.
You can use tabs to view up to 3 web pages at the
same time. Each page appears in a separate tab, and
you can switch between the tabs.
1 Press B on the remote control unit to display the
Tab menu.
• You can also display the Tab menu by clicking “
the toolbar.
Selected item
1 Press D on the remote control unit to display the
toolbar.
2 Press c/d to select a function, and then press
Displays the web page in the
selected tab.
Close This Tab
Closes the selected tab.
• You can also press C on the
remote control unit to close a
tab.
Close Other Tabs
Closes the other (unselected) tabs.
Create New Tab
Creates a new tab.
• You can also press A on the
remote control unit to create a
tab.
Description
Displays the linked page in a new tab.
Displays the Tab menu.
Description
Select This
ENTER.
Selected item
” in
2 Press c/d to select a tab.
3 Press a/b to select the item you want to use, and
then press ENTER.
Returns to the previous page.
Goes back to the original page when you
have viewed the previous page.
Refreshes the page.
Interrupts a page while it is loading.
Displays the original home page.
Select this to open a bookmark.
Adds the current page to your bookmarks.
Displays the Browser menu.
66
LC-40_46_52_60LE830U_E.indb 66
2011/01/06 17:22:33
Using the Internet
Saving the URL of the Current Page
Adding a web page to your bookmarks allows you to
return to that page later by simply selecting it from your
list of bookmarks.
Editing Bookmarks
You can rearrange or delete the bookmarks.
■ Switching between the URL and title name
1 Press D on the remote control unit to display the
toolbar.
2 Press c/d to select “
” in the toolbar, and then
press ENTER.
• Your bookmarks list is displayed.
3 Press a/b to select the title you want to edit from
the bookmarks list, and then press A on the remote
control unit.
• The Bookmarks menu appears.
4 Select “Display by Address” or “Display by Title” in
the Bookmarks menu, and then press ENTER.
1 Display the page that you want to bookmark.
2 Press D on the remote control unit to display the
toolbar.
3
Press c/d to select “
press ENTER.
” in the toolbar, and then
• The page is added to your bookmarks.
Opening a Bookmarked Page
Press D on the remote control unit to display the
toolbar.
2 Press c/d to select “
1 Press D on the remote control unit to display the
toolbar.
2 Press c/d to select “
4 Select “Yes”, and then press ENTER.
1
■ Rearranging displayed items
” in the toolbar, and then
press ENTER.
” in the toolbar, and then
press ENTER.
• Your bookmarks list is displayed.
3 Press a/b to select the title you want to display
in a different position from the bookmarks list, and
then press A on the remote control unit.
• The Bookmarks menu appears.
4 Press a/b to select “Move Up” or “Move Down”,
and then press ENTER.
• Your bookmarks list is displayed.
3 Press a/b/c/d to select the page you want to
■ Deleting bookmarks
access, and then press ENTER.
• The selected page is displayed.
• If you have bookmarked 11 or more web pages, press
c/d to scroll through your bookmarks list.
When opening a bookmark in a new tab:
1 Press A instead of ENTER.
• The Bookmarks menu appears.
2 Select “Open in New Tab”, and then press
ENTER.
1 Press D on the remote control unit to display the
toolbar.
2 Press c/d to select “
” in the toolbar, and then
press ENTER.
• Your bookmarks list is displayed.
3 Press a/b to select the title you want to delete,
and then press A on the remote control unit.
• The Bookmarks menu appears.
4 Press a/b to select “Delete”, and then press
ENTER.
• To delete all the bookmarks, select “Delete All”.
5 Press c/d to select “Yes”, and then press
ENTER.
67
LC-40_46_52_60LE830U_E.indb 67
2011/01/06 17:22:33
Using the Internet
Browser Settings
You can check or modify your browser settings from
the Browser menu.
The Browser menu includes a display settings menu
and a security settings menu.
1 Press D to display the toolbar.
2 Press c/d to select “ ” in the toolbar, and then
press ENTER.
3 Press c/d to select the settings menu you want to
access.
Security Settings
Security:
Save Setting: If you select this option, a message is
displayed when you move from a protected page to an
unprotected page.
To change this setting, remove the tick, select “Save
Setting” and then press ENTER.
Root Certificates/CA Certificates: Displays the list of
certificates. To disable a certificate, select the certificate
to be disabled and press A to display the sub-menu.
Select “Disable”, and then press ENTER.
• Disabled certificates are shown unticked in the
certificate list screen.
Cookies:
Accept all: Select this option to accept all cookies.
Reject all: Select this option when you do not want to
accept cookies.
Prompt before accepting: When you open a page
that uses cookies, this option displays a confirmation
message.
Delete All Cookies: Deletes all your cookies.
Server Certificates: Displays certificates for the connected
server.
Browser Information: Displays browser information.
4 Press a/b to select and confirm the item you want
to set.
5 Press a/b/c/d to specify the required setting,
and then press ENTER.
6 Press D to exit.
View Settings
Zoom In/Out:
Zoom in: Displays content enlarged to 200%.
Normal: Displays content at 100%.
Zoom out: Displays content reduced to 75%.
Encoding: Selects the desired encoding from the list below:
Western (ISO-8859-1)/Unicode (UTF-8)
Page Information: Displays information about the currently
displayed page.
Reset:
Yes: Resets the browser settings.
No: Does not reset the browser settings.
• This
product contains NetFront Browser of
ACCESS CO., LTD.
• ACCESS, the ACCESS logo and NetFront
are registered trademarks or trademarks of
ACCESS CO., LTD. in the United States,
Japan and/or other countries.
© 2009 ACCESS CO., LTD. All rights
reserved.
• This software is based in part on the work of
the Independent JPEG Group.
• “Reset” does not reset the certification enable/disable and
Encoding settings.
68
LC-40_46_52_60LE830U_E.indb 68
2011/01/06 17:22:34
Using the Internet
Using Applications via the Internet
By connecting the TV to the Internet, you can enjoy a
variety of broadband content, including videos, movies,
music, photos, and games.
Please check that the most current software is
loaded on TV by selecting "Auto Update Setting" on
"Software Update" (see page 38) or by visiting
http://www.sharpusa.com/products/support/
to check for a download of the newest software version.
Example
Information
Menu
Information
Identification
Digital Caption Info.
Software Update
Netflix Help
Vudu Help
Deactivating Netflix Function
1 Press MENU to display the menu screen.
2 Press c/d to select "Information", and then press
ENTER.
3 Press a/b to select "Netflix Help", and then press
ENTER.
4 Press c/d to select "Deactivate", and then press
ENTER.
1 Press APPS to display the application window.
Example
• To confirm the Netflix status, check the information
displayed on the screen and click "OK".
Deactivating the VUDU Function
APP1
APP2
APP3
1 Press MENU to display the menu screen.
2 Press c/d to select "Information", and then press
ENTER.
2 Press a/b/c/d to select the desired application,
and then press ENTER.
" is displayed after you connect to the Internet,
• If "
check your TV's network settings and connection.
• When using this TV to access an Internet application
for the first time, the Disclaimer appears on the screen.
Press a/b to select "Agree", and then press ENTER.
(You must select "Agree" to use the application.)
• Additional applications will be available in the future.
3 Press a/b to select "Vudu Help", and then press
ENTER.
4 Press c/d to select "Yes", and then press
ENTER.
3 The screen for the selected application is displayed.
Follow the on-screen instructions for each
application.
• Check the web site of the provider for details on setup
and use of the functions.
• These applications are provided by content providers. The
available applications vary depending on your country or
region.
• The delivery speed of applications varies depending on
the network speed. Check the web site of the provider for
details on application setup and other information.
69
LC-40_46_52_60LE830U_E.indb 69
2011/01/06 17:22:34
Using the Internet
DISCLAIMERS
This Sharp device facilitates the access to content and services provided by third parties. The content and
services accessible via this device belong to and may be proprietary to third parties. Therefore, any use of such
third party content and services must be in accordance with any authorization or terms of use provided by
such content or service provider. Sharp shall not be liable to you or any third party for your failure to abide by
such authorization or terms of use. Unless otherwise specifically authorized by the applicable content or service
provider, all third party content and services provided are for personal and non-commercial use; you may not
modify, copy, distribute, transmit, display, perform, reproduce, upload, publish, license, create derivative works
from, transfer or sell in any manner or medium any content or services available via this device.
Sharp is not responsible, nor liable, for customer service-related issues related to the third party content or
services. Any questions, comments or service-related inquiries relating to the third party content or service
should be made directly to the applicable content or service provider.
You may not be able to access content or services from the device for a variety of reasons which may be
unrelated to the device itself, including, but not limited to, power failure, other Internet connection, or failure to
configure your device properly. Sharp, its directors, officers, employees, agents, contractors and affiliates shall
not be liable to you or any third party with respect to such failures or maintenance outages, regardless of cause
or whether or not it could have been avoided.
ALL THIRD PARTY CONTENT OR SERVICES ACCESSIBLE VIA THIS DEVICE IS PROVIDED TO YOU
ON AN “AS-IS” AND “AS AVAILABLE” BASIS AND SHARP AND ITS AFFILIATES MAKE NO WARRANTY
OR REPRESENTATION OF ANY KIND TO YOU, EITHER EXPRESS OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, ANY WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, FITNESS FOR A PARTICULAR
PURPOSE OR ANY WARRANTIES OF SUITABILITY, AVAILABILITY, ACCURACY, COMPLETENESS, SECURITY,
TITLE, USEFULNESS, LACK OF NEGLIGENCE OR ERROR-FREE OR UNINTERRUPTED OPERATION OR USE
OF THE CONTENT OR SERVICES PROVIDED TO YOU OR THAT THE CONTENT OR SERVICES WILL MEET
YOUR REQUIREMENTS OR EXPECTATIONS.
SHARP IS NOT AN AGENT OF AND ASSUMES NO RESPONSIBILITY FOR THE ACTS OR OMISSIONS OF
THIRD PARTY CONTENT OR SERVICE PROVIDERS, NOR ANY ASPECT OF THE CONTENT OR SERVICE
RELATED TO SUCH THIRD PARTY PROVIDERS.
IN NO EVENT WILL SHARP AND/OR ITS AFFILIATES BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE, CONSEQUENTIAL OR OTHER DAMAGES, WHETHER
THE THEORY OF LIABILITY IS BASED ON CONTRACT, TORT, NEGLIGENCE, BREACH OF WARRANTY,
STRICT LIABILITY OR OTHERWISE AND WHETHER OR NOT SHARP AND/OR ITS AFFILIATES HAVE BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
70
LC-40_46_52_60LE830U_E.indb 70
2011/01/06 17:22:34
Appendix
Removing the Stand
• Before detaching (or attaching) the stand, unplug the AC cord.
CAUTION
• Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
■ LC-40LE830U/LC-46LE830U/LC-52LE830U
Before attaching/detaching the stand
• Before performing work, make sure to turn off the TV.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being
damaged.
1
2
LC-40LE830U
LC-46LE830U
LC-52LE830U
1
1
2
Loosen the screw used to secure the stand cover
and remove the cover.
1 Unfasten the four screws used to secure the
stand in place.
2 Detach the stand from the TV. (Hold the stand so
it will not drop from the edge of the base area.)
• To attach the stand, perform the above steps in reverse order.
■ LC-60LE830U
Before attaching/detaching the stand
• Before performing work, make sure to turn off the TV.
1
2
3
Unfasten the four screws used to
secure the stand in place.
Detach the stand from the TV.
2
1
1 Loosen the screw used to
secure the stand cover.
2 Remove the cover.
• To attach the stand, perform the above steps in reverse order.
71
LC-40_46_52_60LE830U_E.indb 71
2011/01/06 17:22:34
Appendix
Setting the TV on the Wall
CAUTION
LC-40LE830U
• This TV should be mounted on the wall with both the AN-37AG2 (SHARP) wall mount bracket and the AN-37P30
(SHARP) attachment of the wall mount bracket. The TV cannot be mounted when with only the AN-37AG2 wall
mount bracket. The use of other wall mount brackets may result in an unstable installation and may cause
serious injuries.
LC-46LE830U/LC-52LE830U/LC-60LE830U
• This TV should be mounted on the wall only with the wall mount bracket AN-52AG4 (SHARP). The use of other
wall mount brackets may result in an unstable installation and may cause serious injuries.
• Installing the TV requires special skill that should only be performed by qualified service personnel. Customers
should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or
mounting that results in accident or injury.
Using an optional bracket to mount the TV
• You can ask a qualified service professional about using an optional AN-37AG2+AN-37P30 or AN-52AG4 bracket to
mount the TV on the wall.
• Carefully read the instructions that come with the bracket before beginning work.
Hanging on the wall
About setting the TV angle
AN-37AG2+AN-37P30 or AN-52AG4 wall
mount bracket.
(See the bracket instructions for details.)
LC-40/46/52LE830U
0/5/10/15/20°
LC-60LE830U
0/5/10°
AN-37AG2 + AN-37P30
LC-40LE830U
• The center of the display:
1
/32 inch (0.5 mm) above the “A” position.
AN-52AG4
LC-46LE830U
• The center of the display:
3
/32 inch (2.0 mm) under the “b” position.
LC-52LE830U
• The center of the display:
9
/32 inch (7.0 mm) under the “b” position.
Vertical mounting
Angular mounting
LC-60LE830U
• The “e” position is at the center of the display.
• Refer to the operation manual of
AN-37AG2+AN-37P30 or AN-52AG4 for details.
• Detach the cable tie on the rear of the TV when using the optional mount
bracket.
• Due to the terminal configuration on this TV, when you wall-mount this
model, make sure there is enough space between the wall and the TV for
the cables.
• To use this TV mounted on a wall, remove the AC cord holder and the
covers at the 4 locations on the rear of the TV, and then use the screws
supplied with the wall mount bracket to secure the bracket to the rear of
the TV.
1
2
1
Optional Accessories
The listed optional accessories are available for the Liquid
Crystal Television. Please purchase them at your nearest
shop.
• Additional optional accessories may be available in the near
future. When purchasing, please read the newest catalogue for
compatibility and check the availability.
Part name
Wall mount
bracket
Attachment
AN-37AG2 (for LC-40LE830U)
Model number
Wall mount
bracket
AN-52AG4 (for LC-46LE830U/
LC-52LE830U/LC-60LE830U)
AN-37P30 (for LC-40LE830U)
72
LC-40_46_52_60LE830U_E.indb 72
2011/01/06 17:22:34
Appendix
Troubleshooting
Problem
Possible Solution
• No power
• Check if you pressed POWER on the remote control unit.
• Is the AC cord disconnected? Page 9
• Has the power been turned on? Page 18
• Unit cannot be operated.
• External influences such as lightning, static electricity, may cause improper
operation. In this case, operate the unit after first turning off the power of the TV or
unplugging the AC cord and replugging it in after 1 or 2 minutes.
• Remote control unit does not
operate.
• Is the equipment to be operated by the remote control unit set correctly? Press TV
to set the remote control unit to the setting for operating the TV.
• Are batteries inserted with polarity (e, f) aligned? Page 10
• Are batteries worn out? (Replace with new batteries.)
• Are you using it under strong or fluorescent lighting?
• Is a fluorescent light illuminated near the remote control sensor?
• Is "RC Control Lock" selected in "Operation Lock Out"? Page 33
• Picture is cut off/with sidebar
screen.
• Is the image position correct? Pages 32 and 57
• Are screen mode adjustments such as picture size made correctly?
Pages 24 and 56
• Strange color, light color, or color
misalignment
• Adjust the picture tone. Pages 27 and 28
• Is the room too bright? The picture may look dark in a room that is too bright.
• Power is suddenly turned off.
• Is the sleep timer set? Page 21
• Check the power control settings. Page 30
• The unit's internal temperature has increased. Remove any objects blocking vent or
clean.
• No sound
•
•
•
•
•
•
•
•
•
•
Page 18
Is connection to other components correct? Pages 13 to 17 and 52
Is the volume too low? Page 21
Is "Variable" selected in "Output Select"? Page 32
Have you pressed MUTE on the remote control unit? Page 21
Check the audio output of the connected external equipment. Is the volume too
low or muted?
When external equipment is connected via an HDMI cable, you may need to
configure the audio to be output through the HDMI cable.
When audio is not output from external equipment connected to the PC IN or HDMI 1
terminal, check the "Audio Select" setting. Page 57
Even when external equipment is connected using an HDMI-certified cable, an audio
cable connection may be required depending on the type of equipment and the
media being played back. In this case, in addition to connecting an HDMI-certified
cable to the HDMI 1 terminal, connect a Ø 3.5 mm stereo minijack cable to the
AUDIO IN terminal and set "Audio Select" to "HDMI+Analog". Page 57
When connecting a PC via an HDMI-certified cable, check the following:
- Is the audio output of the PC configured correctly? Check the audio output
settings and output audio format in Sound Properties on the PC.
Only PCM format audio can be output. Compressed audio (with a sampling rate
of 32kHz, 44.1kHz, or 48kHz) and DTS format audio cannot be output.
- Depending on the board, only video signals may be output. In this case, in
addition to connecting an HDMI-certified cable to the HDMI 1 terminal, connect a
Ø 3.5 mm stereo minijack cable to the AUDIO IN terminal and set "Audio Select"
to "HDMI+Analog". Page 57
If you are using a DVI-HDMI conversion cable to connect external equipment to the
TV, check the following:
- Is an audio cable connected? The DVI-HDMI conversion cable is for video only.
Connect a Ø 3.5 mm stereo minijack cable to listen to the audio.
- Is HDMI 1 being used? When the TV is connected to another HDMI terminal, the
audio and video are not output together even if a Ø 3.5 mm stereo minijack cable
is connected to the shared AUDIO IN terminal for PC IN and HDMI 1.
- Check the "Audio Select" setting. Set "Audio Select" to "HDMI+Analog". Page 57
73
LC-40_46_52_60LE830U_E.indb 73
2011/01/06 17:22:34
Appendix
Problem
Possible Solution
• No picture
•
•
•
•
Is connection to other components correct? Pages 13 to 17 and 52
Is the correct input selected? Pages 13 and 22
Is "On" selected in "Audio Only"? Page 30
If the PC image is not displayed, check the following:
- When connecting a laptop PC to the TV, check that display output mode of the
PC is set to external monitor.
- Check the resolution setting on the PC. Is a non-compatible signal being input?
Page 57
• Picture quality of HD programs is
poor.
• To enjoy HD images from external equipment, you are required to set up HDMI
connection or component connection.
• If the program content is not of HD quality, HD images cannot be displayed. Check
that the program you are viewing provides HD images.
• The HD cable/satellite set-top box may need to be configured to output HD images
via cable/satellite.
• The cable/satellite broadcast may not support a signal resolution of 1080p.
• The TV sometimes makes a
cracking sound.
• This is not a malfunction. This happens when the cabinet slightly expands and contracts
according to change in temperature. This does not affect the TV's performance.
• The original home page cannot
be displayed.
• Is the ETHERNET cable connected correctly? Page 60
• Check the settings of "Internet Setup".
Pages 62 to 63
• Some Internet functions used on a
PC are not available from the TV.
• The TV has only limited functions compared with regular PC browsers.
Page 65
Troubleshooting - Error Message
The example of an error message
displayed on a screen
Error code
Possible Solution
• Failed to receive broadcast.
E202
• Check the antenna cable. Check that the antenna is correctly setup.
• No broadcast now.
E203
• Check the broadcast time in the program guide.
• An incompatible audio signal has
been received. Change the output
device audio settings to PCM.
—
• This message is displayed when an audio format other than PCM
is input. (Dolby Digital and DTS audio formats are not supported.)
- Set the audio output format of connected external HDMI
equipment to PCM.
- Refer to the operation manual of the external equipment for
setting details.
74
LC-40_46_52_60LE830U_E.indb 74
2011/01/06 17:22:34
Appendix
CLEARING THE SECRET NUMBER
If you forget the secret number, clear the secret number using the following procedure.
Select an item from the list below to display the secret number input screen. (For operating the on-screen
display menu, see page 25.)
System Options menu).
• "Color system" ( "Input Terminal Setting"
• "EZ Setup" or "Reset" ( Initial Setup menu).
• "CH Setup” ( "Broadcasting Setup"
Initial Setup menu).
• "Parental CTRL" ( "Individual Setup"
Initial Setup menu).
• "Interactive Service" ( "Internet Setup"
Initial Setup menu).
• "Software Update" ( Information menu).
Press and hold both CHr and VOLk on the TV simultaneously until the message appears on the screen.
➝
➝
➝
➝
The secret number is
➝
➝
➝
➝
➝
2
➝
1
.
• As a precautionary measure, make a note of your secret number above, and keep it in a safe place.
Trademarks
• Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
• “HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.”
• Products that have earned the ENERGY STAR® are designed to protect the environment through superior energy
efficiency.
•
and LC logo mark are registered trademarks of SHARP Corporation.
This product is embedded with LC Font technology, which was developed by SHARP Corporation for clearly
displaying easy-to-read characters on LCD screens. However, other fonts are used for some screen pages, too.
• “x.v.Color” and
are trademarks of Sony Corporation.
• Netflix and the Netflix logo are the registered trademarks of Netflix, Inc.
• VUDU™ is a trademark of VUDU, Inc.
• DivX®, DivX Certified®, DivX Plus™ HD and associated logos are trademarks of DivX, Inc. and are used under
license.
• ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, Inc. This is an official DivX Certified® device that
plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX video.
• ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX
Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup
menu. Go to vod.divx.com for more information on how to complete your registration.
• The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance.
• The Wi-Fi Protected Setup Mark is a mark of the Wi-Fi Alliance.
• DLNA®, the DLNA Logo and DLNA CERTIFIED™ are trademarks, service marks, or certification marks of the Digital
Living Network Alliance.
• Contains Adobe® Flash® Lite® by Adobe Systems Incorporated. Adobe Flash Lite Copyright © 2003-2011 Adobe
System Incorporated. All rights reserved.
Adobe Flash and Flash Lite are either registered trademarks or trademarks of Adobe Systems Incorporated in the
United States and/or other countries.
75
LC-40_46_52_60LE830U_E.indb 75
2011/01/06 17:22:34
Specifications
TV
Item
LCD
panel
Model: LC-40LE830U
Size
40o Class (40o Diagonal)
Resolution
2,073,600 pixels (1,920 g 1,080)
TV-standard (CCIR)
TV
Function
Receiving
Channel
Model: LC-46LE830U
46o Class (45 63/64o Diagonal)
American TV Standard ATSC/NTSC System
VHF/UHF
VHF 2-13ch, UHF 14-69ch
CATV
1-135ch (non-scrambled channel only)
Digital Terrestrial
Broadcast (8VSB)
2-69ch
*1
Digital cable
(64/256 QAM)
Audio multiplex
1-135ch (non-scrambled channel only)
BTSC System
10W g 2 + 15 W (WF)
Audio out
HDMI 1
HDMI 2
Back panel HDMI 3
vertical
HDMI 4
inputs
AUDIO OUT
HDMI in with HDCP, Audio in (Ø 3.5 mm stereo jack)
HDMI in with HDCP
HDMI in with HDCP
HDMI in with HDCP
Audio out (Ø 3.5 mm stereo jack)
USB 1
Photo/Music/Video mode, Software update
COMPONENT
COMPONENT in
VIDEO 1
AV in
Terminals Back panel VIDEO 2
surface
inputs
PC IN
AV in
ANALOG RGB (PC) in (15-pin mini D-sub female connector),
Audio in (Ø 3.5 mm stereo jack)
RS-232C
9-pin D-sub male connector
ANT/CABLE
75 q Unbalance, F Type g 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
AUDIO IN
Back panel
DIGITAL AUDIO OUTPUT
horizontal
inputs
ETHERNET
USB 2
Audio in (Ø 3.5 mm stereo jack)
Optical Digital audio output g 1 (PCM/Dolby Digital)
Network connector
Photo/Music/Video mode, Software update
OSD language
English/French/Spanish
Power Requirement
AC 120 V, 60 Hz
Power Consumption
118 W (0.1 W Standby with AC 120 V)
142 W (0.1 W Standby with AC 120 V)
TV + stand
36.4 lbs./16.5 kg
50.7 lbs./23.0 kg
TV only
29.8 lbs./13.5 kg
Weight
*2
Dimension
(W g H g D)
Operating temperature
TV + stand
TV only
15
3
15
5
41.9 lbs./19.0 kg
25
36 /16 g 25 /64 g 10 /64 inch
5
36 /16 g 23 /32 g 1 /8 inch
42 13/64 g 28 g 11 35/64 inch
42 13/64 g 26 7/64 g 1 5/8 inch
e32°F to e104°F (0°C to e40°C)
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.
This is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the front panel to malfunction.
Storage temperature: f4°F to e140°F (f20°C to e60°C)
76
LC-40_46_52_60LE830U_E_07.indd 76
2011/01/07 14:45:38
Specifications
Item
LCD
panel
Model: LC-52LE830U
Size
52o Class (52 1/32o Diagonal)
Resolution
2,073,600 pixels (1,920 g 1,080)
TV-standard (CCIR)
TV
Function
Receiving
Channel
Model: LC-60LE830U
60o Class (60 1/32o Diagonal)
American TV Standard ATSC/NTSC System
VHF/UHF
VHF 2-13ch, UHF 14-69ch
CATV
1-135ch (non-scrambled channel only)
Digital Terrestrial
Broadcast (8VSB)
2-69ch
*1
Digital cable
(64/256 QAM)
Audio multiplex
1-135ch (non-scrambled channel only)
BTSC System
10W g 2 + 15 W (WF)
Audio out
HDMI 1
HDMI 2
Back panel HDMI 3
vertical
HDMI 4
inputs
AUDIO OUT
HDMI in with HDCP, Audio in (Ø 3.5 mm stereo jack)
HDMI in with HDCP
HDMI in with HDCP
HDMI in with HDCP
Audio out (Ø 3.5 mm stereo jack)
USB 1
Photo/Music/Video mode, Software update
COMPONENT
COMPONENT in
VIDEO 1
AV in
Terminals Back panel VIDEO 2
surface
inputs
PC IN
AV in
ANALOG RGB (PC) in (15-pin mini D-sub female connector),
Audio in (Ø 3.5 mm stereo jack)
RS-232C
9-pin D-sub male connector
ANT/CABLE
75 q Unbalance, F Type g 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
AUDIO IN
Back panel
DIGITAL AUDIO OUTPUT
horizontal
inputs
ETHERNET
USB 2
Audio in (Ø 3.5 mm stereo jack)
Optical Digital audio output g 1 (PCM/Dolby Digital)
Network connector
Photo/Music/Video mode, Software update
OSD language
English/French/Spanish
Power Requirement
AC 120 V, 60 Hz
Power Consumption
Weight
*2
Dimension
(W g H g D)
Operating temperature
162 W (0.1 W Standby with AC 120 V)
213 W (0.1 W Standby with AC 120 V)
TV + stand
61.7 lbs./28.0 kg
83.8 lbs./38.0 kg
TV only
52.9 lbs./24.0 kg
TV + stand
TV only
31
63
31
1
68.3 lbs./31.0 kg
35
47 /64 g 30 /64 g 11 /64 inch
5
47 /64 g 29 /16 g 1 /8 inch
54 29/64 g 34 31/32 g 14 27/64 inch
54 29/64 g 33 1/32 g 1 5/8 inch
e32°F to e104°F (0°C to e40°C)
*1
Emergency alert messages via Cable are unreceivable.
The dimensional drawings are shown on the inside back cover.
The dimensions include projecting parts.
• As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
*2
77
LC-40_46_52_60LE830U_E.indb 77
2011/01/06 17:22:35
Specifications
Wireless LAN
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. To comply with the FCC RF exposure compliance
requirements, this device and its antenna must not be co-located or operated in conjunction with any other antenna or
transmitter.
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel
mobile satellite systems;
The maximum antenna gain permitted (for devices in the bands 5250-5350 MHz and 5470-5725 MHz) to comply with the e.i.r.p.
limit; and High-power radars are allocated as primary users (meaning they have priority) of the bands 5250-5350 MHz and
5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.
COFETEL
This equipment operates on a secondary basis and, consequently, must accept harmful interference, including from station of
the same kind, and may not cause harmful interference to systems operating on a primary basis.
CONTAINS TRANSMITTER MODULE COFETEL ID: RCPSHRU10-1387
Brand: SHARP
Model: RUNTKA810WJQZ
Standard
Frequency Band
Security
Modulation
Transmit Power and Sensitivity
Specification
IEEE 802.11a/b/g/n
2412-2484 MHz
5150-5850 MHz
Static WEP (64/128 bit key Index 1 only)
WPA-PSK (TKIP)
WPA2-PSK (AES)
DBPSK@1Mbps
DQPSK@2Mbps
CCK@5.5/11Mbps
BPSK@6/9 Mbps
QPSK@12/18Mbps
16-QAM@24Mbps
64-QAM@48/54Mbps and above, Rx up to 300Mbps
Tx Output Power: (Typical)
2.4GHz
11b 17 +/- 2 dBm
11g 14 +/- 2 dBm
11n 13 +/- 2 dBm
5GHz
11a 14 +/- 2 dBm
11n 13 +/- 2 dBm
Rx Sensitivity: (Typical)
-84dBm@11Mbps
-72dBm@54Mbps
-65dBm@HT20
-62dBm@HT40
78
LC-40_46_52_60LE830U_E_07.indd 78
2011/01/07 12:02:33
Information on the Software License for This Product
■ Software composition
The software included in this product is comprised of various software components whose individual copyrights
are held by SHARP or by third parties.
■ Software developed by SHARP and open source software
The copyrights for the software components and various relevant documents included with this product that were
developed or written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties,
and other relevant laws. This product also makes use of freely distributed software and software components
whose copyrights are held by third parties. These include software components covered by a GNU General Public
License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license agreement.
■ Obtaining source code
Some of the open source software licensors require the distributor to provide the source code with the executable
software components. GPL and LGPL include similar requirements. For information on obtaining the source code
for the open source software and for obtaining the GPL, LGPL, and other license agreement information, visit the
following website:
http://www.sharpusa.com/gpl
We are unable to answer any questions about the source code for the open source software. The source code for
the software components whose copyrights are held by SHARP is not distributed.
■ Acknowledgements
The following are some of the open source software components included in this product:
• linux kernel/busybox/glibc/zlib/libpng/libjpeg/libiconv/DirectFB/OpenSSL/XMLRPC-EPI/mtd-utils/Expat/Qt/
U-Boot/WMDRM/AGG(ver2.3)/device-mapper/libfreetype/cURL/libxml2/lua/lua-xmlreader/lua-slncrypto/
Ffmpeg/SQLite/libzzip/c-ares/librt/libjanus
For the complete list, please see the URL above.
79
LC-40_46_52_60LE830U_E_07.indd 79
2011/01/07 12:02:33
Information on the Software License for This Product
■ Software Copyrights
XMLRPC-EPI
Copyright 2000 © Epinions, Inc.
libjpeg
This software is copyright © 1991-1998, Thomas G. Lane.
Portions of this software are based in part on the work of the Independent JPEG Group.
OpenSSL
Copyright © 1998-2008 The OpenSSL Project.
This product includes software developed by the OpenSSL Project for use in the OpenSSL
Toolkit. (http://www.openssl.org)
SSLeay
Copyright © 1995-1998 Eric Young (eay@cryptsoft.com)
This product includes cryptographic software written by Eric Young (eay@cryptsoft.com).
Expat
Copyright © 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper.
Copyright © 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.
Qt
The Qt GUI Toolkit is Copyright © 2010 Nokia Corporation and/or its subsidiary(-ies).
Contact: Nokia Corporation (qt-info@nokia.com)
WMDRM
Content owners use Windows Media digital rights management technology (WMDRM) to protect their
intellectual property, including copyrights. This device uses WMDRM software to access WMDRMprotected content. If the WMDRM software fails to protect the content, content owners may ask Microsoft
to revoke the software’s ability to use WMDRM to play or copy protected content.
Revocation does not affect unprotected content. When you download licenses for protected content,
you agree that Microsoft may include a revocation list with the licenses. Content owners may require
you to upgrade WMDRM to access to their content. If you decline an upgrade, you will not be able to
access content that requires the upgrade.
libfreetype
Copyright © 2006, 2007, 2008, 2009, 2010 by David Turner, Robert Wilhelm, and Werner Lemberg.
cURL
Copyright © 1996-2010, Daniel Stenberg, (daniel@haxx.se)
libxml2
Copyright © 1998-2003 Daniel Veillard. All Rights Reserved.
Lua
Copyright © 1994-2008 Lua.org, PUC-Rio
Lua-xmlreader
Copyright © 2008 A.S. Bradbury
Lua-slncrypto
Copyright © 2005 Malete Partner, Berlin, partner@malete.org
libzzip
Copyright © Guido Draheim guidod@gmx.de
c-ares
Copyright © 1998 by the Massachusetts Institute of Technology.
UPnP
Portions copyright © 2004 Intel Corporation
Group 42
Portions copyright © 2000 Group 42, Inc. and the Contributing Authors.
zlib
Portions copyright © 1995-1996 Jean-loup Gailly and Mark Adler.
RSA Data Security
MD5.CPP - RSA Data Security, Inc., MD5 message-digest algorithm. Copyright © 1991-2, RSA Data
Security, Inc. Created 1991. All rights reserved.
Fraunhofer IIS and Thomson Multimedia
MPEG Layer-3 audio compression technology licensed by Fraunhofer IIS and Thomson Multimedia.
You cannot use the MP3 compressed audio within the Software for real time or live broadcasts.
If you require an MP3 decoder for real time or live broadcasts, you are responsible for obtaining this
MP3 technology license.
Nellymoser, Inc
Speech compression and decompression technology licensed by Nellymoser, Inc.
Sorenson Media, Inc
SorensonTM SparkTM video compression and decompression technology licensed from Sorenson Media,
Inc.
Sun Microsystem, Inc
ADPCM speech compression algorithm is used with the permission of Sun Microsystems, Inc.
80
LC-40_46_52_60LE830U_E.indb 80
2011/01/06 17:22:35
Calling for Service
For location of the nearest Sharp Authorized Service, or to obtain product literature, accessories, supplies, or
customer assistance, please call 1-800-BE-SHARP.
LIMITED WARRANTY
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand Liquid Crystal Display product (the
“Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option,
either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the
purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product or if the serial number or model number affixed to the Product has
been removed, defaced, changed, altered or tampered with. This warranty does not cover installation or signal reception problems. This
limited warranty will not apply if the Product has been or is being used in a commercial setting or application; this warranty is meant solely
for the non-commercial, household use of the Product by consumers in their home or residence. If you intend to or already use this Product
for commercial purposes or in a commercial setting, there are warranties available to cover your use of this Product, the terms of which may
vary. Please contact 1-888-GO-SHARP for further information.
In order to enforce your rights under this limited warranty, you should follow the steps set forth below. You must be able to provide proof of
purchase to the servicer, which proof must include the date of purchase.
To the extent permitted by applicable state law, the warranties set forth are in lieu of, and exclusive of, all other warranties, express or
implied. Specifically ALL OTHER WARRANTIES OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED, ALL EXPRESS AND
IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE, AND FITNESS FOR A PARTICULAR
PURPOSE ARE SPECIFICALLY EXCLUDED. IF, UNDER APPLICABLE STATE LAW, IMPLIED WARRANTIES MAY NOT VALIDLY BE
DISCLAIMED OR EXCLUDED, THE DURATION OF SUCH IMPLIED WARRANTIES IS LIMITED TO THE PERIOD(S) FROM THE DATE OF
PURCHASE SET FORTH BELOW. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
The warranties given herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy
available to the purchaser and only for the time periods set forth herein. No other representations or promises made by anyone are
permitted. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all
liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims,
whether based on contract, negligence, strict liability or otherwise. Sharp does not warrant nor shall Sharp be liable, or in any way
responsible, for Products which have been subject to abuse (including, but not limited to, improper voltage), accident, misuse, negligence,
lack of reasonable care, alteration, modification, tampering, misuse, improper operation or maintenance or any damages or defects in the
Product which were caused by repairs or attempted repairs performed by anyone other than a Sharp authorized servicer. Nor shall Sharp
be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow limits on
warranties or on remedies for breach in certain transactions; in such states, the limits herein may not apply.
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND PUERTO RICO.
Model Specific Section
Your Product Model Number & Description:
LC-40LE830U/LC-46LE830U/LC-52LE830U/LC-60LE830U LCD Color Television
(Be sure to have this information available when you need service for your
Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
Additional Exclusions from
Warranty Coverage (if any):
In order for the Product to be serviced, the Product must be readily available
to the servicer, free and clear of any complex or non-standard installation,
mounting or other encumbrance which would unreasonably interfere with
servicing the Product. The Servicer will remount the Product after service,
provided that such remounting is not into a complex or non-standard installation. Any additional labor and materials required to remove and/or reinstall a
Product above and beyond the foregoing are not covered by this warranty,
may result in additional charges and are the responsibility of the consumer.
Image Retention resulting from a fixed image being displayed for long
periods of time is not covered by this Limited Warranty (see Operation
Manual on how to prevent this).
Where to Obtain Service:
From a Sharp Authorized Servicer located in the United States. To find the
location of the nearest Sharp Authorized Servicer, please call Sharp toll free
at 1-800-BE-SHARP.
What to do to Obtain Service:
Contact your Sharp Authorized Servicer to obtain in home service for this
product. The Servicer will come to your location and if necessary remove the
unit for repair at the Servicer’s facility and return the set to you once
completed. Be sure to have Proof of Purchase available.
TO OBTAIN PRODUCT INFORMATION OR PURCHASE ACCESSORIES AND EXTENDED WARRANTIES, CALL 1-800-BE-SHARP
OR VISIT www.sharpusa.com
81
LC-40_46_52_60LE830U_E.indb 81
2011/01/06 17:22:35
82
LC-40_46_52_60LE830U_E.indb 82
2011/01/06 17:22:35
Dimensional Drawings
LC-40LE830U
1 5/8 (41)*4
10 25/64
(264)
9 3/32
(231)
19°
20°
12 59/64
(328)
11 13/16
(300)
2 9/16 (65)
11 13/16 (300)
4 57/64 (124)
18 1/8 (460)
1 63/64 (50)
14 11/64 (360)
34 7/8 (885.6)*1
19 5/8*1
(498.15)
25 3/64 (636)
1 5/16 (33.4)*3
4 37/64
(116)
36 15/16 (938)
23 5/32 (588)
Unit: inch (mm)
Unité: pouce (mm)
Unidad: pulgada (mm)
1 3/64 (26.4)*2
4 47/64
(120)
6 55/64 (174)
10 43/64
(271)
AN-37AG2
+
AN-37P30
LC-46LE830U
1 3/64 (26.4)*2
1 5/8 (41)*4
11 35/64
(293)
10 5/16
(262)
20°
8 15/32 (215)
14 3/8 (365)
3/4
15 3/4 (400)
(19)
15 3/4 (400)
7 7/8 (200)
19 31/32 (507)
3 5/64 (78)
15 43/64 (398)
40 3/32 (1018.08)*1
22 9/16*1
(572.67)
28 (711)
26 7/64 (663)
1 5/16 (33.4)*3
5 11/64
(131)
42 13/64 (1072)
3 63/64
(101)
11 55/64
(301)
AN-52AG4
*1
*2
*3
*4
Active area/Área activa/Zone active
Thinnest part/Parte más delgada/Partie la plus mince
Excluding projecting parts/Excluyendo partes salientes/Sauf les parties saillantes
Including projecting parts/Incluyendo partes salientes/Parties saillantes incluses
LC-40_46_52_60LE830U_S.indb 84
2011/01/06 20:56:16
Dimensional Drawings
1 3/64 (26.4)*2
LC-52LE830U
1 5/8 (41)*4
11 35/64
(293)
19 31/32 (507)
11 47/64
(298)
20°
15 3/4 (400)
3/4
15 3/4 (400)
(19)
7 3/32 (180)
15 3/4 (400)
4 19/64 (109)
17 11/64
(436)
45 23/64 (1152.0)*1
25 33/64*1
(648.0)
29 1/16 (738)
30 63/64 (787)
47 31/64 (1206)
Unit: inch (mm)
Unité: pouce (mm)
Unidad: pulgada (mm)
1 5/16 (33.4)*3
5 11/64
(131)
3 63/64
(101)
8 15/32 (215)
12 9/32
(312)
AN-52AG4
1 3/64 (26.4)*2
LC-60LE830U
1 5/16 (33.4)*3
6 5/16
(160)
54 29/64 (1383)
1 5/8 (41)*4
14 27/64 (366)
21 7/64 (536)
*2
*3
*4
LC-40_46_52_60LE830U_E_Cover.ind2 2
15 3/32 (383)
17 31/64 (444)
15 3/4 (400)
8 15/32 (215)
*1
10°
9 1/16 (230)
2 1/16 (52)
15 3/4 (400)
5 23/32 (145)
19 9/64 (486)
29 7/16*1
(747.63)
33 1/32 (839)
34 31/32 (888)
52 11/32 (1329.12)*1
3 63/64
(101)
8 13/64
(208)
Active area/Área activa/Zone active
AN-52AG4
Thinnest part/Parte más delgada/Partie la plus mince
Excluding projecting parts/Excluyendo partes salientes/Sauf les parties saillantes
Including projecting parts/Incluyendo partes salientes/Parties saillantes incluses
2011/01/26 22:12:05
OPERATION MANUAL
MODE D'EMPLOI
Sharp Plaza, Mahwah, New Jersey 07495-1163
SHARP CORPORATION
ENGLISH
FRANÇAIS
ESPAÑOL
LC-40LE830U/LC-46LE830U/LC-52LE830U/LC-60LE830U
SHARP ELECTRONICS CORPORATION
LC-40LE830U
LC-46LE830U
LC-52LE830U
LC-60LE830U
LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR ACL
TELEVISOR CON PANTALLA
DE CRISTAL LÍQUIDO
OPERATION MANUAL
MODE D'EMPLOI
MANUAL DE OPERACIÓN
MANUAL DE OPERACIÓN
Printed in Mexico
Imprimé au Mexique
Impreso en México
TINS-F030WJZZ
11P02-MX-NM
IMPORTANT : Please read this operation manual before starting operating the equipment.
IMPORTANT : Veuillez lire ce mode d'emploi avant de commencer à utiliser l'appareil.
IMPORTANTE : Lea este manual de operación antes de comenzar a operar el equipo.
LC-40_46_52_60LE830U_E_Cover.ind1 1
2011/01/26 22:12:04