FRANÇAIS
ENGLISH
LC-90LE745U
LC-90LE745U
OPERATION MANUAL
SHARP ELECTRONICS CORPORATION
ESPAÑOL
LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR ACL
TELEVISOR CON PANTALLA
DE CRISTAL LÍQUIDO
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE OPERACIÓN
MODE D'EMPLOI
Sharp Plaza, Mahwah, New Jersey 07495-1163
SHARP CORPORATION
MANUAL DE OPERACIÓN
Printed in Mexico
Imprimé au Mexique
Impreso en México
TINS-F501WJZZ
12P05-MX-NM
IMPORTANT : Please read this operation manual before starting operating the equipment.
IMPORTANT : Veuillez lire ce mode d'emploi avant de commencer à utiliser l'appareil.
IMPORTANTE : Lea este manual de operación antes de comenzar a operar el equipo.
LC-90LE745U_E_Cover.indd 1
2012/03/27 19:42:33
Dimensional Drawings
Unit: inch (mm)
Unité: pouce (mm)
Unidad: pulgada (mm)
2 11/16 (68)*2
3 45/64 (94)
7
80 /8 (2054)
4 37/64 (116)
6 25/32
(172)
25 9/16 (649)
44 9/64 (1121.04)*1
47 11/16 (1211)
1 17/64
(32)
48 61/64 (1243)
78 15/32 (1992.96)*1
29 1/32 (737)
17 3/32 (434)
5
3
15 /16 (389)
15 /4 (400)
7 7/8 (200)
23 5/8 (600)
18 5/32 (461)
*1
*2
LC-90LE745U_E_Cover.indd 2
Active area/Área activa/Zone active
Thinnest part/Parte más delgada/Partie la plus mince
2012/03/27 19:42:33
ENGLISH
LC-90LE745U
LIQUID CRYSTAL TELEVISION
ENGLISH
OPERATION MANUAL
IMPORTANT:
To aid reporting in case of loss or theft, please record the
TV's model and serial numbers in the space provided. Find
the numbers at the side of the TV where the control panel is
located.
Model No.:
Serial No.:
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION:
The lightning flash with arrow-head
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within a
triangle is intended to alert the user
to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the product.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly
approved by the manufacturer could void the user's authority to operate this equipment.
1
LC-90LE745U_E.indb 1
2012/04/06 16:49:51
IMPORTANT INFORMATION
CAUTION:
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded
cables and connectors for connections.
DECLARATION OF CONFORMITY:
SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-90LE745U
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RESPONSIBLE PARTY:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
TEL: 1-800-BE-SHARP
For Business Customers: URL http://www.sharpusa.com
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Wireless Radio
For product available in the USA/Canada market, only channel 1–11 can be operated. Selection of other channels is not possible.
This device is going to be operated in 5.15–5.25GHz frequency range, it is restricted in indoor environment only.
Important: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Wireless Radio
For product available in the USA/Canada market, only channel 1–11 can be operated. Selection of other channels is not possible.
The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure.
Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where
required by the technology.
Important: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator
& your body.
“Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820 of the National
Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as practical.”
2
LC-90LE745U_E.indb 2
2012/04/06 16:49:51
DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years
of trouble-free operation of your product, please read the Important Safety Instructions carefully before
using this product.
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage
if improperly handled. This product has been engineered and manufactured with the highest priority on safety.
However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please
observe the following instructions when installing, operating and cleaning the product. To ensure your safety
and prolong the service life of your Liquid Crystal Television, please read the following precautions carefully
before using the product.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Additional Safety Information
15) Power Sources—This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery power, or other sources, refer to the
operating instructions.
16) Overloading—Do not overload wall outlets, extension cords, or integral convenience receptacles as this
can result in a risk of fire or electric shock.
17) Object and Liquid Entry—Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
18) Damage Requiring Service—Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an improper adjustment
of other controls may result in damage and will often require extensive work by a qualified technician
to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this indicates a need for service.
19) Replacement Parts—When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
20) Safety Check—Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
21) Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product
according to the method recommended by the manufacturer.
3
LC-90LE745U_E.indb 3
2012/04/06 16:49:51
IMPORTANT SAFETY INSTRUCTIONS
• Outdoor Antenna Grounding — If an outside antenna is
connected to the television equipment, be sure the antenna
system is grounded so as to provide some protection against
voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250)
NEC — NATIONAL ELECTRICAL CODE
• Water and Moisture — Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool; and the like.
• Stand — Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base
can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart,
stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product
on a wall, be sure to follow the manufacturer's instructions. Use only the mounting hardware recommended by the
manufacturer.
• Selecting the location — Select a place with no direct sunlight and good ventilation.
• Ventilation — The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents
and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place
the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not
designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper
ventilation is provided or the manufacturer's instructions are followed.
• The front panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with
impact. Be careful not to be injured by broken glass pieces in case the panel breaks.
• Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
• The Liquid Crystal panel is a very high technology product with 2,073,600 pixels, giving you fine picture details.
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this
does not affect the performance of your product.
• Lightning — For added protection for this television equipment during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to
the equipment due to lightning and power-line surges.
• Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
• To prevent fire, never place any type of candle or flames on the top or near the TV set.
• To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.
• Do not display a still picture for a long time, as this could cause an afterimage to remain.
• To prevent fire or shock hazard, do not expose this product to dripping or splashing.
No objects filled with liquids, such as vases, should be placed on the product.
• Do not insert foreign objects into the product. Inserting objects in the air vents or other openings may
result in fire or electric shock. Exercise special caution when using the product around children.
Precautions when transporting the TV
• When transporting the TV, never carry it by holding or otherwise putting
pressure onto the display. Be sure to always carry the TV by three people
holding it with two hands.
4
LC-90LE745U_E_01.indd 4
2012/04/09 14:56:43
IMPORTANT SAFETY INSTRUCTIONS
Caring for the cabinet
• Use a soft cloth (cotton, flannel, etc.) and gently wipe the surface of the cabinet.
• Using a chemical cloth (wet/dry sheet type cloth, etc.) may deform the components of the cabinet or cause cracking.
• Wiping with a hard cloth or using strong force may scratch the surface of the cabinet.
• If the cabinet is very dirty, wipe with a soft cloth (cotton, flannel, etc.) soaked in neutral detergent diluted with water and
thoroughly wrung out, and then wipe with a soft dry cloth.
• Avoid using benzene, thinner, and other solvents, as these may deform the cabinet and cause the paint to peel off.
• Do not apply insecticides or other volatile liquids.
Also, do not allow the cabinet to remain in contact with rubber or vinyl products for a long period of time. Plasticizers
inside the plastic may cause the cabinet to deform and cause the paint to peel off.
Caring for the front panel
• Turn off the main power and unplug the AC cord from the wall outlet before handling.
• Gently wipe the surface of the front panel with a soft cloth (cotton, flannel, etc.).
To protect the front panel, do not use a dirty cloth, liquid cleaners, or a chemical cloth (wet/dry
sheet type cloth, etc.). This may damage the surface of the front panel.
• Wiping with a hard cloth or using strong force may scratch the surface of the front panel.
• Use a soft damp cloth to gently wipe the front panel when it is really dirty.
(It may scratch the surface of the front panel when wiped strongly.)
• If the front panel is dusty, use an anti-static brush, which is commercially available, to clean it.
• To avoid scratching the frame or screen, please use a soft, lint free cloth for cleaning. Approved cleaning cloths are
available directly from Sharp in single (00Z-LCD-CLOTH) or triple (00Z-LCD-CLOTH-3) packs. Call 1-800-BE-SHARP for
ordering, or VISIT http://www.sharpusa.com/SharpDirect.
CHILD SAFETY:
It Makes A Difference How and Where You Use Your Flat Panel Display
Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind:
THE ISSUE
• The home theater entertainment experience is a growing trend and larger flat panel displays
are popular purchases. However, flat panel displays are not always supported on the proper
stands or installed according to the manufacturer’s recommendations.
• Flat panel displays that are inappropriately situated on dressers, bookcases, shelves, desks,
speakers, chests or carts may fall over and cause injury.
THIS MANUFACTURER CARES!
• The consumer electronics industry is committed to making home entertainment enjoyable
and safe.
TUNE INTO SAFETY
• One size does NOT fit all. Follow the manufacturer’s recommendations for the safe installation
and use of your flat panel display.
• Carefully read and understand all enclosed instructions for proper use of this product.
• Don’t allow children to climb on or play with furniture and television sets.
• Don’t place flat panel displays on furniture that can easily be used as steps, such as a chest
of drawers.
• Remember that children can become excited while watching a program, especially on a
“larger than life” flat panel display. Care should be taken to place or install the display where it
cannot be pushed, pulled over, or knocked down.
• Care should be taken to route all cords and cables connected to the flat panel display so that
they cannot be pulled or grabbed by curious children.
WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT YOUR FLAT PANEL DISPLAY, ALWAYS:
• Use a mount that has been recommended by the display manufacturer and/or listed by an independent laboratory (such
as UL, CSA, ETL).
• Follow all instructions supplied by the display and wall mount manufacturers.
• If you have any doubts about your ability to safely install your flat panel display, contact your retailer about professional
installation.
• Make sure that the wall where you are mounting the display is appropriate. Some wall mounts are not designed to be
mounted to walls with steel studs or old cinder block construction. If you are unsure, contact a professional installer.
• A minimum of two people are required for installation. Flat panel displays can be heavy.
Note: CEA is the preeminent trade association promoting growth in the $161 billion U.S.
consumer electronics industry. More than 2,200 companies enjoy the benefits of CEA
membership, including legislative advocacy, market research, technical training and
education, industry promotion and the fostering of business and strategic relationships.
5
LC-90LE745U_E.indb 5
2012/04/06 16:49:52
IMPORTANT SAFETY INSTRUCTIONS
3D Glasses
Prevention of accidental ingestion
• Keep the accessory out of the reach of small children. Small children can accidentally swallow these parts.
– If a child accidentally swallows any of these parts, seek immediate medical attention.
Do not disassemble
• Do not disassemble or modify the 3D Glasses except when recycling the batteries. Do not modify the 3D Glasses.
Caution for lithium ion polymer rechargeable battery
• Do not expose the 3D Glasses to excessive heat, such as direct sunlight, fire or in an area with high humidity.
Handling the 3D Glasses
• Do not drop, exert pressure on, or step on the 3D Glasses. Doing so may damage the glass section, which may result in
the risk of injury.
• Be careful not to trap your finger in the hinge section of the 3D Glasses. Doing so may result in injury.
– Pay special attention when children are using this product.
Using the 3D Glasses
• Use of the 3D Glasses should be limited to a maximum of 3 hours, and in any case no more than one movie.
• Use only the 3D Glasses recommended for this TV.
• Use the 3D Glasses only for the specified purpose.
• Do not move around while wearing the 3D Glasses. The surrounding area may appear dark, which may result in falling or
other accidents that may cause injury.
Caring for the 3D Glasses
• Use only the cloth provided with the 3D Glasses to clean the lenses. Remove dust and soil from the cloth. Any dust or
other soiling on the cloth may result in scratches. Do not use solvents such as benzene or thinners as doing so may
damage the coating.
• When cleaning the 3D Glasses, take care not to allow water or other fluids to come into contact with the glasses.
• Always store the 3D Glasses in the case provided when not in use.
• When storing the 3D Glasses, avoid very humid or hot locations.
Viewing 3D images
• If you experience dizziness, nausea, or other discomfort while viewing 3D images, discontinue use and rest your eyes.
• Do not use the 3D Glasses if they are cracked or broken.
Caution regarding rechargeable battery
• Use the supplied USB cable to connect to a USB terminal of a 3D compatible SHARP TV when recharging. Recharging
using other devices may lead to battery damage.
Caution regarding the power supply
• Use the USB cable to connect to a USB terminal of a 3D compatible SHARP TV for supplying power. Supplying power
using other devices may lead to heat generation or battery damage.
• During a thunderstorm, to avoid getting an electric shock, do not use the 3D Glasses that are power-supplied via USB,
and do unplug the USB cable from both the USB terminal on the TV and the USB terminal on the 3D Glasses.
6
LC-90LE745U_E.indb 6
2012/04/06 16:49:52
Contents
IMPORTANT INFORMATION . . . . . . . . . . . . . . . . . . . 1-2
DEAR SHARP CUSTOMER . . . . . . . . . . . . . . . . . . . . . . . 3
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . 3-6
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
QUICK REFERENCE
Attaching the Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
QUICK INSTALLATION TIPS . . . . . . . . . . . . . . . . . . 10
Experiencing HD Images . . . . . . . . . . . . . . . . . . . . . . 10
Using the Remote Control Unit . . . . . . . . . . . . . . . . 10
Preparation
Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installing Batteries in the Remote Control Unit . . . 11
Part Names
TV (Front/Side) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
TV (Rear) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Remote Control Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Introduction to Connections
Types of Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Displaying an External Equipment Image . . . . . . . 14
Connecting to External Equipment
Connecting a Blu-ray Disc/DVD Player or
HD Cable/Satellite Set-top Box . . . . . . . . . . . 15-16
Connecting a VCR, Game Console,
Camcorder or Cable/Satellite Set-top Box . . . . 16
Connecting a Surround System/Audio System . . 17
Connecting a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Watching TV
Turning On/Off the Power . . . . . . . . . . . . . . . . . . . . . 19
Initial Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-22
Direct Button Operation
INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Changing Channels . . . . . . . . . . . . . . . . . . . . . . . . 23
Changing Volume . . . . . . . . . . . . . . . . . . . . . . . . . . 23
MUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
FREEZE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
FLASHBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SmartCentral . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
NETFLIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
AV MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25
Closed Captions and
Digital Closed Captions . . . . . . . . . . . . . . . . . . . 25
VIEW MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
On-Screen Display Menu
On-Screen Display Menu Operation . . . . . . . . . . . 27
Menu Operation Buttons . . . . . . . . . . . . . . . . . . . . . . 27
Menu Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-30
Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Power Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-35
Initial Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-39
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-42
Enjoying 3D Image Viewing
Display Methods for 3D and 2D Images. . . . . . . . 43
3D Glasses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-46
Viewing 3D Images . . . . . . . . . . . . . . . . . . . . . . . . . 47-48
Configuring the TV Settings to Enhance
3D Image Viewing. . . . . . . . . . . . . . . . . . . . . . . . . 48-50
Specifications - 3D Glasses. . . . . . . . . . . . . . . . . . . . 51
Enjoying Photo/Music/Video Playback
Connecting a USB Memory Device/
USB Hard Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Connecting a Home Network (DLNA) Server . . . 52
Selecting the Folders to Play Back . . . . . . . . . . . . . 53
Playing Back Files on a USB Memory Device/
Home Network (DLNA) Server. . . . . . . . . . . . . 54-58
Playing Back Files from a Portable Device or
PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Other Viewing Options
Presetting Remote Control Function . . . . . . . . . . . 59
Operating the Connected Equipment . . . . . . . 59-60
Using AQUOS LINK
Controlling HDMI Equipment
Using AQUOS LINK . . . . . . . . . . . . . . . . . . . . . . . 61-63
Link Operation Menu . . . . . . . . . . . . . . . . . . . . . . . 63-64
Using a Smartphone with the TV. . . . . . . . . . . . . . . 65
Using a PC
Displaying a PC Image on the Screen . . . . . . . . . . 66
Adjusting the PC Image . . . . . . . . . . . . . . . . . . . . . . . 67
Setting Audio Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
PC Compatibility Chart . . . . . . . . . . . . . . . . . . . . . . . . 67
Control of the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 68-69
Using the Internet
Connecting to the Internet . . . . . . . . . . . . . . . . . . . . . 70
Internet Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71-72
AQUOS Advantage Live . . . . . . . . . . . . . . . . . . . . . . . 72
Entering Text (Software Keyboard) . . . . . . . . . . . . . 73
Using the Browser. . . . . . . . . . . . . . . . . . . . . . . . . . 74-75
Using Applications via the Internet . . . . . . . . . . 76-77
Enjoying Skype™ . . . . . . . . . . . . . . . . . . . . . . . . . . 78-81
DISCLAIMERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Appendix
Removing the Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Setting the TV on the Wall . . . . . . . . . . . . . . . . . . . . . 84
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85-86
Troubleshooting - 3D Images . . . . . . . . . . . . . . . . . . 86
Troubleshooting - Error Message . . . . . . . . . . . . . . 86
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Specifications
TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Information on the Software License for
This Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90-92
Calling for Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Dimensional Drawings
• The dimensional drawings for the LCD TV set are shown
on the inside back cover.
• The illustrations and on-screen displays in this operation manual are for explanation purposes and may vary slightly from
the actual operations.
7
LC-90LE745U_E_01.indd 7
2012/04/06 17:39:19
Accessories
Supplied Accessories
Make sure the following accessories are provided with the product.
Remote control unit (x1)
“AAA” size battery (x2)
Stand unit (x1)
Page 10
Page 11
Page 9
AC cord (x1)
3D Glasses (x2)
Operation manual (x1)
Page 10
See pages 44 to 46 for
details of the 3D Glasses
and their accessories.
Connection guide (x1)
• Always use the AC cord supplied with the TV.
• The illustrations above are for explanation purposes and may vary slightly from the actual accessories.
Optional Accessories
The listed optional accessories are available for the Liquid
Crystal Television. Please purchase them at your nearest
shop.
Part name
3D Glasses
Model number
AN-3DG20
• Additional optional accessories may be available in the near
future. When purchasing, please read the newest catalogue for
compatibility and check the availability.
8
LC-90LE745U_E.indb 8
2012/04/06 16:49:52
QUICK REFERENCE
Attaching the Stand
• Before attaching (or detaching) the stand, unplug the AC cord.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged.
CAUTION
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
• After attaching the stand to the TV, do not hold the stand when you put up, set up, move or lay down the TV.
• Do not remove the stand from the TV unless using a wall mount bracket to mount it.
Before attaching the stand to the TV, build a work
table on which to rest the TV.
5
• To build the table, use the cushioning materials used in the
packaging.
TOP-L
The case is equipped with push-in tabs to hold
the cushioning materials in place. Push in the
tabs (2 for each location) to secure the cushioning
materials in the case.
Push-in tabs
TOP-R
TOP-C
FRO
NT
• Of the cushioning materials used, TOP-C is also used
during stand unit assembly. Be sure to assemble the stand
unit before building the work table.
6
■ Stand Unit Assembly
1
2
After you have built the work table, spread a
blanket or similar soft cloth over the table and then
lay the TV display down on the covered table.
• Do not use a small table for this.
Confirm that there are 12 screws (8 long screws
and 4 short screws) supplied with the stand unit.
1 Set the post for the stand unit onto the TOP-C.
2 Attach the base to the post.
3 Insert and tighten the 8 screws into the 8 holes
on the bottom of the base.
• Hold the stand unit securely with one hand, and then
tighten the screws.
3
Long
screws
■ Attaching the Stand to the TV
7
• Make sure that the stand is firmly inserted into the TV.
Improper installation may result in tilting of the TV set.
2
Insert the stand into the openings on the bottom of
the TV.
1
1
FRONT
■ Building the Work Table
3
8
Attach the joints and close the case.
1 Insert a joint into the hole on the side of the case.
2 Pressing the tab, fix the joint into place.
Insert and tighten the 4 screws into the 4 holes on
the rear of the TV.
Short
screws
1
2
4
Insert each of the cushioning materials in the
respective directions shown in the figure.
• Insert TOP-L and TOP-R into the left and right sides of
the case respectively.
• Insert TOP-C to fit between the lines on the other side
of the case.
• In the installation procedure, be careful not to catch your
fingers between the TV set and the floor.
TOP-L
LINE
CASE
TOP-R
JOINT
TOP-C
LC-90LE745U_E.indb 9
9
2012/04/06 16:49:52
QUICK REFERENCE
QUICK INSTALLATION TIPS
1
2
Attach your antenna to the back of the television.
(See page 11.)
Connect the AC plug for the television into the AC outlet.
Experiencing HD Images
An HDTV without an HD source is just an ordinary
TV.
To enjoy HD images on the TV, you should get
HD programming from the following:
• Over-the-air broadcasting via HD quality antenna
• HD cable/satellite subscription
• HD compatible external equipment
• For information on updating to HD programming, ask your
cable/satellite service provider.
AC outlet
• Place the TV close to the AC outlet, and keep the power
plug within reach.
• TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
TOUCH UN-INSULATED PARTS OF ANY CABLES
WITH THE AC CORD CONNECTED.
3
Using the Remote Control Unit
Use the remote control unit by pointing it towards the
remote control sensor on the TV. Objects between the
remote control unit and the remote control sensor may
prevent proper operation.
Bundle the cords properly with the cable tie.
Remote control sensor
30°
17´ (5 m)
30°
30°
30°*
* The angle is 8º when the stand is attached.
4
When turning on the TV for the first time, press
POWER on the television.
POWER
5
■ Cautions regarding the remote control unit
• Do not expose the remote control unit to shock. In addition,
do not expose the remote control unit to liquids, and do not
place in an area with high humidity.
• Do not install or place the remote control unit under direct
sunlight. The heat may cause deformation of the remote
control unit.
• The remote control unit may not work properly if the remote
control sensor on the TV is under direct sunlight or strong
lighting. In such cases, change the angle of the lighting
or the TV, or operate the remote control unit closer to the
remote control sensor.
Insert the batteries into the remote control unit. (See
page 11.)
• Speakers cannot be detached from the TV.
• The TV angle cannot be adjusted.
IMPORTANT:
IF THE UNIT DOES NOT POWER ON - UNPLUG THE
TELEVISION FROM THE OUTLET AND REPEAT THE
INSTALLATION STEPS.
IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT
US AT 1-800-BE-SHARP.
10
LC-90LE745U_E_01.indd 10
2012/05/11 10:16:22
Preparation
Antennas
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections
that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector,
plug it into the antenna terminal at the rear of the TV set. For connecting the antenna cable to the TV, use
commercially available cables.
Connecting Antenna Cable
• Connect the antenna cable to the TV using one of the methods in the illustration as shown (1, 2, 3 or 4).
1 Cable without a CATV
converter
Home Antenna
terminal (75-ohm)
Cable TV lead-In
Coaxial cable
2 VHF/UHF antenna
Home Antenna
terminal (75-ohm)
75-ohm coaxial cable (round)
Coaxial cable
3 Combination VHF/
UHF antenna
75-ohm coaxial cable (round)
or
300-ohm twin-lead cable (flat)
4 Separate VHF/UHF
antenna
VHF
ANTENNA
UHF
ANTENNA
300/75-ohm adapter
300-ohm
twin-lead cable
OUT
IN
300-ohm twin-lead cable
or
Combiner
75-ohm coaxial cable
To TV antenna
terminal
F-type connector
1. A 75-ohm system is generally a round cable with F-type connector
that can easily be attached to a terminal without tools.
2. A 300-ohm system is a flat “twin-lead” cable that can be attached
to a 75-ohm terminal through a 300/75-ohm adapter.
75-ohm coaxial cable (round)
300-ohm twin-lead cable (flat)
NOTICE
F-type connector should be finger-tightened only.
When connecting the RF cable to the TV set, do not tighten F-type
connector with tools.
If tools are used, it may cause damage to your TV set. (The breaking
of internal circuit, etc.)
F-type connector
75-ohm coaxial cable
Installing Batteries in the Remote Control Unit
If the remote control fails to operate TV functions, replace the batteries in the remote control unit.
2 Insert two “AAA” size batteries (supplied with
3 Close the battery cover.
1 Open the battery cover.
the product).
• Place the batteries
with their terminals
corresponding to the (e)
and (f) indications in the
battery compartment.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage
in old batteries.
• Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with skin can cause a
rash. If you find any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove batteries from it.
11
LC-90LE745U_E.indb 11
2012/04/06 16:49:52
Part Names
TV (Front/Side)
*1
POWER
button
MENU
button
INPUT
button
3D infrared emitter *2
Channel
buttons
(CHU/V)
Volume
buttons
(VOLk/l)
OPC sensor *3
Remote control sensor
Center Icon illumination
(See page 35.)
*1 See pages 14, 19 and 27 for button operations.
*2 This panel emits the infrared signal towards the 3D Glasses you wear when you view 3D images.
Do not place anything between the 3D infrared emitter on the TV and the infrared receiver on the 3D Glasses.
When the TV is in 3D mode, the emitter may look reddish.
*3 OPC: Optical Picture Control (See page 29.)
TV (Rear)
*1
RS-232C terminal
PC IN terminal
VIDEO 2 terminals
VIDEO 1 terminals
COMPONENT
terminals
*1
AUDIO OUT terminal
*1
USB 1 terminal
HDMI 1 terminal
ARC: Audio Return Channel
(See pages 61 and 62.)
HDMI 2 terminal
USB 2
terminal
ETHERNET
terminal
Antenna/
Cable in
DIGITAL AUDIO
OUTPUT terminal
AUDIO IN terminal
(shared for PC IN
and HDMI 2) *2
HDMI 3 terminal
HDMI 4 terminal
MHL: Mobile High-Definition Link
(See page 65.)
*1 See pages 14 to 18 and 61 for external equipment connection.
*2 See page 67 for details on the Audio Select function.
12
LC-90LE745U_E_01.indd 12
2012/04/24 9:43:35
Part Names
Remote Control Unit
1
2
20
21
6
7
22
8
9
10
11
12
23
24
25
26
13
27
16
17
2
TV, STB, DVD•VCR, AUDIO: Switches the remote
control for TV, STB, BD, DVD, VCR and AUDIO operation.
(See pages 59 to 60 for details.)
* To enter the code registration mode, you need to press
an appropriate button (STB, DVD•VCR or AUDIO) and
DISPLAY at the same time.
3
External equipment operational buttons: Operate the
external equipment.
4
OPTION: Display the Link Operation Menu screen. This
button will function only when AQUOS LINK is used. (See
pages 61 to 64 for details.)
5
SLEEP: Set the sleep timer. (See page 23.)
6
0–9: Set the channel. (See page 23.)
7
• (DOT): (See pages 23 and 59.)
8
CC: Display captions from a closed-caption source. (See
page 25.)
9
AV MODE: Select an audio or video setting. (See page 24.)
10 MUTE: Mute the sound. (See page 23.)
11 VOLk/l: Set the volume. (See page 23.)
12 MENU: Display the menu screen. (See page 27.)
13 3D: Select between 3D and 2D image viewing. (See
pages 47 to 48 for details.)
14 a/b/c/d, ENTER: Select a desired item on the screen.
15 EXIT: Turn off the menu screen.
16 FAVORITE CH: Set the favorite channels. (See page 37.)
17 A, B, C, D: Select 4 preset favorite channels in 4 different
categories. (See page 37.)
While watching, you can toggle the selected channels by
pressing A, B, C and D.
14
15
POWER: Switch the TV power on or enter standby. (See
page 19.)
18
19
3
4
5
1
28
29
30
18 DISPLAY: Display the channel information.
19 POWER (SOURCE): Turns the power of the external
equipment on and off.
20 FREEZE: Set the still image. Press again to return to
normal screen. (See page 23.)
21 AUDIO: Selects the MTS/SAP or the audio mode during
multichannel audio broadcasts. (See pages 24 to 25.)
22 ENT: Jumps to a channel after selecting with the 0–9
buttons.
23 FLASHBACK: Return to the previous channel or external
input mode. (See page 24.)
24 VIEW MODE: Select the screen size. (See pages 26 and
66.)
25 INPUT: Select a TV input source. (TV, HDMI1, HDMI2,
HDMI3, HDMI4, COMPONENT, VIDEO1, VIDEO2, PC IN,
Home Network (DLNA), USB) (See pages 14 and 23.)
• When using the remote control unit, point it at the TV.
26 CHU/V: Select the channel. (See page 23.)
27 SmartCentral: Display the application window. (See
page 24.)
28 RETURN: Return to the previous menu screen.
29 NETFLIX: Display the Netflix screen. (See page 24.)
30 FAV APP 1, 2, 3: You can assign your favorite
applications to these buttons. (See page 76.)
13
LC-90LE745U_E.indb 13
2012/04/06 16:49:52
Introduction to Connections
Types of Connection
For connecting the TV to external equipment, use commercially available cables.
• The illustrations of the terminals are for explanation purposes and may vary slightly from the actual products.
■ Connecting to video equipment or a PC
Image quality differs depending on the terminal used. To enjoy clearer images, check the output terminals of your
external equipment and use its appropriate terminals for higher quality images.
Image
Quality
Terminal
on the TV
Terminal on external
equipment
Cable
HD
Quality
HDMI-certified cable
Pages
15, 17, 18
Ø 3.5 mm stereo minijack cable
Pages
15, 18
AUDIO
DVI-HDMI conversion cable
DVI OUT
Component video cable
Page 16
Audio cable
AV cable
Standard
Quality
Page 16
■ Connecting to audio equipment
Terminal on the TV
Terminal on external
equipment
Cable
Optical fiber cable
Page 17
OPTICAL
DIGITAL AUDIO INPUT
Ø3.5 mm stereo minijack to RCA audio cable
Page 17
ANALOG AUDIO IN
Displaying an External Equipment Image
To view external source images, select the input source by pressing INPUT on the remote control unit or on the TV.
Example
1 Press INPUT.
• The INPUT list screen displays.
Menu
Input
AIR
INPUT
INPUT
TV
HDMI1
HDMI2
HDMI3
2 Press a/b to select the input source.
• You can also select the input source by pressing
INPUT. Each time INPUT is pressed, the input source
toggles.
HDMI1
TV
HDMI2
HDMI3
HDMI4
• An image from the selected source automatically
displays.
• If the corresponding input is not plugged in, you
cannot change the input. Be sure to connect the
equipment beforehand.
14
LC-90LE745U_E_01.indd 14
2012/04/11 13:33:39
Connecting to External Equipment
You can connect many types of external equipment to your TV. To view external source images, select the input
source by pressing INPUT on the remote control unit or on the TV. (See pages 14 and 23.)
For connecting the TV to external equipment, use commercially available cables.
CAUTION
• To protect equipment, always turn off the TV before connecting any external equipment.
• Please read the relevant operation manual (Blu-ray disc player, etc.) carefully before making connections.
Connecting a Blu-ray Disc/DVD Player or HD Cable/Satellite Set-top Box
■ When using an HDMI cable (HDMI 1, 2, 3 or 4):
The HDMI (High Definition Multimedia Interface) terminal is an audio-video interface that enables a connection for audio and
video signals using a single cable. The HDMI terminal supports high-resolution video input.
• Blu-ray disc player
• DVD player
• HD cable/satellite set-top box
HDMI-certified cable
HDMI OUT
• To enjoy 1080p display capability, connect your external equipment using an HDMI-certified cable or a component cable
and set the equipment to 1080p output.
• Supported Audio format: Linear PCM/Dolby Digital, sampling rate 32/44.1/48kHz.
• When you connect ARC-compatible equipment, use HDMI 1.
■ When using a DVI-HDMI conversion cable (HDMI 2):
• Blu-ray disc player
• DVD player
• HD cable/satellite set-top box
DVI-HDMI conversion cable
Ø 3.5 mm stereo minijack cable
AUDIO
DVI OUT
• When using a DVI-HDMI conversion cable, you should make an analog audio connection. In this case, in addition to
connecting a DVI-HDMI conversion cable to the HDMI 2 terminal, connect a Ø 3.5 mm stereo minijack cable to the AUDIO
IN terminal and set "Audio Select" to "HDMI+Analog". (See page 67.)
15
LC-90LE745U_E.indb 15
2012/04/06 16:49:53
Connecting to External Equipment
■ When using a component cable (COMPONENT):
• Blu-ray disc player
• DVD player
• HD cable/satellite set-top box
Audio cable
AUDIO-R (Red)
AUDIO-L (White)
COMPONENT OUT
PR (Red)
Y (Green)
PB (Blue)
Component video cable
• To enjoy 1080p display capability, connect your external equipment using an HDMI-certified cable or a component cable and
set the equipment to 1080p output.
• See page 15 for connecting a Blu-ray disc player, DVD player or an HD cable/satellite set-top box to the HDMI terminal.
Connecting a VCR, Game Console, Camcorder or Cable/Satellite Set-top Box
■ When using a composite cable (VIDEO 1 or 2):
• Game console
• Camcorder
VIDEO (Yellow)
AUDIO-L (White)
• VCR
• Cable/Satellite set-top box
AV cable
AUDIO-R (Red)
16
LC-90LE745U_E.indb 16
2012/04/06 16:49:53
Connecting to External Equipment
Connecting a Surround System/Audio System
■ When connecting an AV amplifier for a surround system
HD cable/satellite set-top box
HDMI-certified cable *1
HDMI OUT
OPTICAL
DIGITAL AUDIO INPUT
HDMI OUT HDMI IN
Optical fiber cable *2
• Letting the TV output the audio to an AV amplifier:
*1 When you connect ARC-compatible equipment, use the HDMI 1 terminal.
*2 If the equipment to be connected is not compatible with the ARC, connect an optical fiber cable.
• If the image is not in sync with the audio, check the settings of the connected surround system.
■ When connecting an audio amplifier
It is possible to output audio through the DIGITAL AUDIO OUTPUT terminal. (See page 33 for details.)
Optical fiber cable
OPTICAL
DIGITAL AUDIO INPUT
Ø3.5 mm stereo minijack to RCA audio cable
ANALOG AUDIO IN
• See page 34 for details on the Output Select function.
17
LC-90LE745U_E.indb 17
2012/04/06 16:49:53
Connecting to External Equipment
Connecting a PC
Refer to page 67 for a list of PC signals compatible with the TV.
■ When using an HDMI cable (HDMI 1, 2, 3 or 4):
HDMI-certified cable
HDMI OUT
• Depending on the board, only video signals may be output. In this case, in addition to connecting an HDMI-certified cable
to the HDMI 2 terminal, connect a Ø 3.5 mm stereo minijack cable to the AUDIO IN terminal and set "Audio Select" to
"HDMI+Analog". (See page 67.)
• The HDMI terminals only support digital signal.
■ When using a DVI-HDMI conversion cable (HDMI 2):
DVI-HDMI conversion cable
DVI OUT
Ø 3.5 mm stereo minijack cable
AUDIO
• When using a DVI-HDMI conversion cable, you should make an analog audio connection. In this case, in addition to
connecting a DVI-HDMI conversion cable to the HDMI 2 terminal, connect a Ø 3.5 mm stereo minijack cable to the AUDIO IN
terminal and set "Audio Select" to "HDMI+Analog". (See page 67.)
■ When using an analog RGB cable (PC IN):
Analog RGB cable
(D-sub 15-pin cable or VGA cable)
Ø 3.5 mm stereo minijack cable
AUDIO
RGB
• When using an analog RGB cable, input the audio signal to the AUDIO IN terminal of PC IN.
• When connecting a PC to the PC IN, set "Audio Select" to "Video+Audio". (See page 67.)
18
LC-90LE745U_E.indb 18
2012/04/06 16:49:53
Watching TV
Turning On/Off the Power
Initial Installation
When you turn on the TV for the first time, it will
automatically memorize the broadcasting channels
available in the region where you live. Perform the
following steps before you press POWER on the
remote control unit.
POWER
1. Insert the batteries into the remote control unit. (See page 11.)
2. Connect the antenna cable to the TV. (See page 11.)
3. Plug in the AC cord to the AC outlet. (See page 10.)
POWER (On/Standby)
Language (Language setting)
Select from among 3 languages: English, French and
Spanish.
1 Press a/b to select the desired language listed
on the screen, and then press ENTER.
Language
Press POWER on the TV or on the remote control unit
to turn the power on.
Location & Time
TV Location
English
Antenna & Cable/STB
Français
Air/Cable
• The Initial Installation starts when the TV powers on for the
first time. If the TV has been turned on before, the Initial
Installation will not be invoked. For changing the settings of
the Initial Installation, perform "EZ setup" on the Initial Setup
menu on page 36.
Press POWER on the TV or on the remote control unit
again to turn the power off.
• The TV enters standby and the image on the screen
disappears.
Español
CH Search
Network
Completed
Location & Time
Make settings for the country, area and time zone
where you use the TV.
2 Press a/b to select "United States", "Canada" or
"Mexico", and then press ENTER.
United States
• If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the AC outlet.
• Weak electric power is still consumed even when the TV is
turned off.
Canada
Mexico
19
LC-90LE745U_E.indb 19
2012/04/06 16:49:53
Watching TV
3 Press a/b to select the time zone where you are
using the TV, and then press ENTER.
Example
Antenna & Cable/STB
Select the type of connection you will use to
watch TV.
6 Press c/d to select "Antenna & Cable" or "Settop box", and then press ENTER.
EST
CST
MST
PST
Antenna & Cable
AKST
Set-top box
HAST
• The time zone differs depending on the selected
country.
• The factory preset value is the time zone for the capital
of the selected country.
4 Press a/b to select the Daylight Savings Time,
and then press ENTER.
Auto
Manual
Off
To watch TV via an antenna or cable
connection (without using a set-top box):
Select "Antenna & Cable", and then go to step 7.
To watch TV via a set-top box:
1 Select "Set-top box", and then press ENTER.
2 To watch TV, select the input source
corresponding to the terminal connected to the
set-top box. When doing so, you must make
the setting to skip "TV". Press c/d to select
"On", and then press ENTER.
• “Auto” is the default selection.
TV Location
Select "Home" or "Store" for the location where you
plan to install the TV.
On
Off
5 Press c/d to select "Home" or "Store".
Press ENTER to enter the setting.
Select
Home
Store
Home: "Power Saving" is set to "Advanced", and AV
MODE is set to "STANDARD".
Store: "Power Saving" is set to "Off" and AV MODE is
set to "DYNAMIC (Fixed)". Picture Reset and Feature
Demo can be set.
Picture Reset: AV MODE will be set to "DYNAMIC (Fixed)"
regardless of whether Picture Reset is "On" or "Off".
• If you select "On" and there is no operation for 30 minutes:
- AV MODE will be reset to "DYNAMIC (Fixed)" and, when a
3D signal is detected, 3D images will switch to 2D images.
• When "Off" is selected:
- AV MODE will be set to "DYNAMIC (Fixed)".
Feature Demo: When "On" is selected, after all the settings
are completed, the Feature Demo screen is displayed if there
is no operation for several minutes.
• When this is set to "On", the channel on the TV
cannot be changed using the remote control unit or
menu. (e.g. CH U/V, Favorite CH, etc.)
• See page 34 for details on the Input Skip function.
3 Press INPUT to select the input source
corresponding to the terminal connected to the
set-top box. Make the necessary settings on
the connected external equipment.
• See the operation manual of the connected
equipment for setting up the equipment.
Air/Cable (Antenna setting)
Make sure what kind of connection is made with your
TV when selecting "Air" or "Cable".
7 Press c/d to select "Air" or "Cable".
Press ENTER to enter the setting.
Air
Cable
20
LC-90LE745U_E.indb 20
2012/04/06 16:49:53
Watching TV
CH Search (Channel search)
Network
Channel auto search makes the TV look for all
channels viewable in the set area.
When you connect to the Internet on the TV, select the
desired connection method and follow the instructions
shown on the display.
8 When "Air" is selected in Antenna setting:
Press c/d to select "Start", and then press
ENTER.
• Wireless LAN connection is possible only when the WPS
(push button) method is used. If any other method is used,
make settings by Initial Setup > Internet Setup > Network
Setup. (See page 71.)
9 Press c/d to select "Yes", and then press
Start
Cancel
When "Cable" is selected in Antenna setting:
1 Press a/b to select "Analog & Digital Search
Start" to search both analog and digital
broadcasts, or to select "Analog Search Start"
to search only analog broadcasts, and then
press ENTER.
ENTER.
Yes
No
10 Press a/b to select "Wired" or "Wireless", and
then press ENTER.
Analog & Digital Search Start
Wired
Analog Search Start
Wireless
Cancel
• The Channel search will start automatically.
• To exit the Channel search screen, select "Cancel",
and then press ENTER.
2 The Channel search results may include
scrambled channels or channels that are not
viewable in the set area. Press c/d to select
"Yes", and then press ENTER to remove
scrambled channels.
Yes
Connection using an ETHERNET cable:
1 Select "Wired" and press ENTER.
2 Confirm that the TV is properly connected
with the router, and then press "Next". Follow
the instructions on the display to perform the
connection test.
Wireless LAN connection by the WPS method:
1 Select "Wireless" and press ENTER.
2 Follow the instructions on the display, and
finalize the connection after testing its viability.
No
• When you change the network settings, refer to Initial
Setup > Internet Setup > Network Setup. (See page 71.)
21
LC-90LE745U_E.indb 21
2012/04/06 16:49:53
Watching TV
Completed
11 The settings confirmation screen is displayed.
Confirm the information displayed on the screen,
and then press ENTER.
Examples of the settings confirmation screen
When one or more channel is received after
"Antenna & Cable" was selected in step 6 and a
search was carried out.
Language
Location & Time
TV Location
Antenna & Cable/STB
Air/Cable
Search Result
Network Connection
• If no channel is found, confirm the type of connection
made with your TV and try "EZ Setup" again.
(See page 36.)
• For changing the settings of the Initial Installation, perform
"EZ setup" on the Initial Setup menu on page 36.
• To see the list of channels found during Channel search,
press INPUT, and then press d.
: English
: United States/EST/Auto
: Home
: Antenna & Cable
: Air
: Digital 4ch
Analog 7ch
: Not completed
Press the INPUT button,
then the right arrow d,
to see the list of channels found.
OK
When no channel is received after "Antenna &
Cable" was selected in step 6 and a search was
carried out.
Language
Location & Time
TV Location
Antenna & Cable/STB
Air/Cable
Search Result
Network Connection
: English
: United States/EST/Auto
: Home
: Antenna & Cable
: Cable
: No channel
: Not completed
Channel not found.
Antenna/Cable are not properly connected
or Air/Cable setup is incorrect.
Please check your Antenna/Cable connection
and Air/Cable setup.
OK
When "Set-top box" was selected in step 6 and a
search was carried out.
Language
Location & Time
TV Location
Antenna & Cable/STB
TV Input Skip
Network Connection
: English
: United States/EST/Auto
: Home
: Set-top box
: On
: Not completed
Please make sure to change INPUT to the
specific input terminal you are connecting
your set-top box to get the picture.
Closed caption, sub-channel audio
and channel selection need to be selected
with your set-top box.
OK
When you have made network settings in step 9.
Language
Location & Time
TV Location
Antenna & Cable/STB
TV Input Skip
Network Connection
: English
: United States/EST/Auto
: Home
: Set-top box
: On
: OK
Please make sure to change INPUT to the
specific input terminal you are connecting
your set-top box to get the picture.
Closed caption, sub-channel audio
and channel selection need to be selected
with your set-top box.
OK
22
LC-90LE745U_E.indb 22
2012/04/06 16:49:53
Direct Button Operation
Changing Volume
You can change the volume by pressing VOLk/l on
the TV or on the remote control unit.
• To increase the volume, press VOLk.
• To decrease the volume, press VOLl.
20
Audio status
Output device
Speaker
Output Select
Fixed
Variable
Variable sound
Mute
• When “Output Select” is set to “Variable”, the indicator on
the screen changes as shown below.
60
INPUT
To view external source images, select the input source by
pressing INPUT on the remote control unit or on the TV.
1 Press INPUT.
MUTE
• The INPUT list screen displays.
Mutes the current sound output.
Press MUTE.
input source.
• “ ” will be displayed on the screen for 30 minutes, and
the sound is silenced.
2 Press a/b or press INPUT again to select the
• An image from the selected source automatically
displays.
• Each time INPUT is pressed, the input source toggles.
• If the corresponding input is not plugged in, you cannot
change the input. Be sure to connect the equipment
beforehand.
• See pages 14 to 18 and 61 for external equipment
connection.
Changing Channels
You can change channels in several ways.
Method 1
Using CHU/V on the remote control unit or on the TV.
Method 2
Using remote control buttons 0-9, • (DOT).
Examples:
To select a 1 or 2-digit channel number (e. g., Channel 5):
Press 5
ENT.
To select a 3-digit channel number (e. g., Channel 115):
Press 1
1
5
ENT.
To select a 4-digit channel number (e. g., Channel 22.1):
Press 2
2
• (DOT)
1
ENT.
Method 3
Selecting the program from the Channel list.
1 Press INPUT on the remote control unit.
2
• See page 34 for details on the Output Select function.
• The INPUT list displays.
Press c/d to select “AIR” or “CABLE”.
• The Channel list displays.
3 Press a/b to select the desired channel, and then
press ENTER.
• When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
• When you enter 0-9 only, channel selection will be made if
there is no operation within a few seconds.
• If you push “0” by itself, nothing will happen.
• Complete the above steps within a few seconds.
• When you enter 0-9 and • (DOT), channel selection will be
made if there is no operation within a few seconds.
• Within 30 minutes of pressing MUTE, mute can be
canceled by pressing VOLk/l or MUTE.
• Mute will be canceled after 30 minutes have passed.
However, the TV will not suddenly output a loud sound as
the volume level is set to 0 automatically.
Sleep Timer
Allows you to set a time when the TV automatically
switches to standby.
Press SLEEP.
• The remaining time displays when the sleep timer has been set.
• Each time you press SLEEP, the remaining time switches
as shown below.
Off
30
60
90
120
• When set, the time automatically starts counting down.
• If you want to adjust the sleep timer, you can press SLEEP
twice then change the time setting.
• When it is 5 minutes before the time expires, the remaining
time will start to keep appearing every minute.
• Select “Off” by pressing SLEEP to cancel the sleep timer.
• The TV will enter standby when the remaining time reaches 0.
FREEZE
Allows you to capture and freeze a moving image that
you are watching.
Press FREEZE.
• A moving image is captured.
• Press FREEZE again to cancel the function.
• When this function is not available, “No displaying still
image available.” will display.
• The still image automatically goes out after 30 minutes.
• If you are using the freeze function and a broadcast
activates the V-CHIP BLOCK, the freeze function will be
canceled and a V-CHIP BLOCK message will appear.
• You can have the same settings by choosing “Freeze” on
the menu items. (See page 33.)
23
LC-90LE745U_E.indb 23
2012/04/06 16:49:53
Direct Button Operation
FLASHBACK
Press FLASHBACK to switch to the previously tuned
channel or previous input mode.
• Press FLASHBACK again to switch back to the currently
tuned channel.
• FLASHBACK will not work if no channel has been
changed after the TV is turned on.
SmartCentral
Allows you to directly activate various types of
applications.
1 Press SmartCentral to display the application
window.
• Press SmartCentral again to display a list of
applications by category.
2 Press c/d(or a/b) to select the desired
application, and then press ENTER.
• If you changed the display to the list of applications in
step 1, select a category and then an application. See
page 76 for details.
” is displayed after you switch to USB mode,
• If “
check the USB connection.
• If “
” or “
” is displayed after you switch to
Home Network (DLNA) mode or after you connect to
the Internet, check your TV’s network settings and
connection.
• See pages 53, 72 and 76 for details of viewable
applications.
• You can display the application window by choosing “APPS”
on the menu items. (See page 33.)
• When this function is not available, “Can not operate this
function now” will display.
NETFLIX
Displays the Netflix screen.
Press NETFLIX.
• To enjoy Netflix, you need to make:
—a broadband Internet connection (See page 70.)
—settings of Internet Setup (See pages 71 and 72.)
—adjustments for Netflix (See page 76.)
AV MODE
AV MODE gives you several viewing options to choose
from to best match the surrounding environment of the
TV, which can vary due to factors like room brightness,
type of program watched or the type of image input
from external equipment.
Press AV MODE. Current AV MODE displays.
Example:
When the input source is PC IN or HDMI 1 to 4
AUTO
STANDARD
DYNAMIC (Fixed)
MOVIE
DYNAMIC
GAME
PC
USER[
]
AUTO: Optimizes the image quality automatically based
on the room brightness and image signal.
STANDARD: For a highly defined image in a normal
lighting.
MOVIE: For a movie.
GAME: Lowers image brightness for easier viewing.
PC: For PC.
USER: Allows the user to customize settings as desired.
You can set the mode for each input source.
DYNAMIC: For a clear-cut image emphasizing high
contrast, useful for sports viewing.
DYNAMIC (Fixed): Changes the image and sound
settings to the factory preset values. No adjustments
are allowed.
• You can select a different AV MODE item for each input
mode. (For example, select STANDARD for TV input and
DYNAMIC for COMPONENT.)
• When you play games, “GAME” is recommended for AV
MODE.
• You cannot set “GAME” or “PC” when the TV is connected
to the Internet or when the input source is “Home Network
(DLNA)” or “USB”.
• You can have the same settings by choosing “AV MODE”
on the menu items. (See page 29.)
AUDIO
■ MTS/SAP stereo mode
The TV has a feature that allows reception of sound
other than the main audio for the program. This feature
is called Multi-channel Television Sound (MTS). The TV
with MTS can receive mono sound, stereo sound
and Secondary Audio Programs (SAP). The SAP feature
allows a TV station to broadcast other information,
which could be audio in another language or something
completely different like weather information.
You can enjoy Hi-Fi stereo sound or SAP broadcasts
where available.
• Stereo broadcasts: View programs like live sporting
events, shows and concerts in dynamic stereo sound.
• SAP broadcasts: Receive TV broadcasts in either MAIN
or SAP sound.
MAIN sound: The normal program soundtrack (either in
mono or stereo).
SAP sound: Listen to a second language, supplementary
commentary or other information. (SAP is mono sound.)
• Press AV MODE again before the mode displayed on the
screen disappears. The mode changes as shown below:
Example:
When the input source is TV, COMPONENT,
VIDEO 1 or 2
AUTO
STANDARD
DYNAMIC (Fixed)
MOVIE
DYNAMIC
GAME
USER [TV]
24
LC-90LE745U_E_02.indd 24
2012/04/23 13:29:30
Direct Button Operation
If stereo sound is difficult to hear.
• Obtain a clearer sound by manually switching to fixed
mono-sound mode.
You can change MTS as shown below to match the
television broadcast signal.
Press AUDIO to toggle between audio modes.
Examples: when receiving MTS and SAP
MONO
STEREO mode: STEREO
STEREO + SAP mode: ST(SAP)
SAP(ST)
MONO
MAIN + SAP mode: MAIN
MONO mode: MONO
SAP
■ Digital broadcasting audio mode
The types of audio transmitted in a digital broadcast include
SURROUND as well as MONO and STEREO. In addition, it
is possible for multiple audio tracks to accompany a single
video track.
Press ENTER to toggle between audio modes.
Example: when receiving Digital broadcasting
STEREO (Audio1)
STEREO (Audio2)
SURROUND (Audio3)
• MTS only operates while in TV mode.
• You can have the same settings by choosing “Change
Audio” on the menu items. (See page 33.)
Closed Captions and Digital Closed Captions
Your TV is equipped with an internal Closed Caption
decoder. It allows you to view conversations, narration
and sound effects as subtitles on your TV. Closed
Captions are available on some TV programs and on
some VHS home video tapes at the discretion of the
program provider.
Digital Closed Caption service is a new caption service
available only on digital TV programs (also at the
discretion of the service provider). It is a more flexible
system than the original Closed Caption system,
because it allows for a variety of caption sizes and font
styles. When the Digital Closed Caption service is in
use, it will be indicated by the appearance of a 3-letter
abbreviation that also indicates the language of the
Digital Closed Captions: ENG (English), SPA (Spanish),
FRA (French) or other language codes.
Not all programs and VHS videotapes offer closed
captions. Please look for the “1” symbol to ensure
that captions will be shown.
In the Closed Caption system, there can be more than
one caption service provided. Each is identified by its
own number. The “CC1” and “CC2” services display
subtitles of TV programs superimposed over the
program’s picture.
In the Closed Caption system, the “Text1” or “Text2”
services display text that is unrelated to the program
being viewed (e.g., weather or news). These services
are also superimposed over the program currently
being viewed.
LC-90LE745U_E.indb 25
1 Press CC.
• This will present the Closed Caption information display.
2 Press CC while the Closed Caption information is
still on the screen.
• Press repeatedly until you select the desired closed
caption service.
Air
DIGITAL
Audio
Video
CC
Ratings
22.1
:
:
:
:
STEREO
480p (4:3)
1/2 CC1
NONE
Closed Caption
information
• Depending on the number of caption services in the
signal being received, you will see information such as
1/2 or 1/4 displayed.
1/2 means “the first of two services”.
Example:
If a program has three services (Digital CC(ENG), CC1
and Text1), the closed caption display will toggle in this
sequence:
1/3 ENG
2/3 CC1
3/3 Text1
Off
• The CC button keeps a record of the last service
selected in its memory.
If the last closed caption mode (e.g. 1/3 ENG) you
selected is not available for the next program, or on
another channel, the closed caption service that is
available is automatically selected, and this service
appears in parentheses, e.g. “1/3(CC1)”.
Closed Caption services that appear in parentheses will
not be stored in the CC button’s memory as your last
selected service. Only services that you have selected
with the CC button are stored.
Examples:
In a case where there are two closed caption
services provided (for instance, Digital CC(ENG)
and CC1), and Digital CC(ENG) is displayed
as your current selection, if Digital CC(ENG) is
not broadcast for the next program, the other
closed caption service, CC1, will be displayed in
parentheses.
A closed caption service appears in parentheses
because the service you selected is not available
and a different service is displayed on your screen.
“1/1(CC1)” is displayed instead of “1/2/ENG”.
• When “Power Saving” is set to “Standard” or “Advanced”,
the Power Saving leaf icon appears on the channel
information window. See page 32 for details of Power
Saving settings.
• See page 34 for detailed closed caption settings.
• When the program contains no closed caption, “--”
displays in the closed caption information.
• If the language code, e.g. “ENG”, is not found on Digital TV
programs, “--” will be shown.
• Four kinds of closed caption service (CC1, CC2, Text1,
Text2) are potentially available, but a broadcast may
contain none or only some of these services at the
discretion of the program provider.
• When a web page is displayed, Closed Captions are not
available.
• You can have the same settings by choosing “Change CC”
on the menu items. (See page 33.)
25
2012/04/06 16:49:54
Direct Button Operation
VIEW MODE
You can select the screen size.
1 Press VIEW MODE.
• The View Mode menu displays.
• The menu lists the View Mode options selectable for the type of video signal currently
being received.
2 Press VIEW MODE or a/b while the View Mode menu is displayed to select a
desired item on the menu.
• You can sequentially select a View Mode that has its own aspect ratio.
• You can have the same settings by choosing "View Mode" on the menu items. (See page 33.)
• You may not be able to change the View Mode while in 3D mode.
■ For HD programs
Stretch
Suitable for viewing widescreen 1.78:1 aspect ratio
program, stretch mode will still
show very thin black bands
at the top and bottom of the
screen.
Dot by Dot (Full Screen)
S.Stretch (Smart stretch)
Dot by Dot (1080i/p only):
Suitable for stretching 4:3
Detects the resolution of the
programs to fill the screen.
signal and displays an image
with the same number of
pixels on the screen.
Full Screen (720p only): You
can select "Full Screen" only
when receiving a 720p signal.
Zoom
Suitable for viewing widescreen 2.35:1 aspect-ratio
programs in full screen.
• When using Dot by Dot or Full Screen, it is possible to see noise or bars around different outer portions of the screen. Please
change view mode to correct this.
■ For 4:3 programs
Example: Screen size images
Side Bar
Suitable for viewing
conventional 4:3 programs in
their normal format.
S.Stretch (Smart stretch)
Suitable for stretching 4:3
programs to fill the screen.
Zoom
Suitable for viewing widescreen 2.35:1 anamorphic
DVDs in full screen.
Stretch
This mode is useful for 1.78:1
DVDs. When viewing 1.85:1
DVDs, stretch mode will still show
very thin black bands at the top
and bottom of the screen.
■ For USB-Video, DLNA-Video or Internet applications
Example: Screen size images
Input signal
Auto
Keeps the original
aspect ratio in a full
screen display.
Original
Displays an image by
an original size.
26
LC-90LE745U_E.indb 26
2012/04/06 16:49:54
On-Screen Display Menu
On-Screen Display Menu Operation
LCFONT embedded
System
Options
: Select
Initial
Setup
ENTER
: Enter
RETURN
Picture
Settings
Information
: Back
MENU
: Exit
Example
Example
Menu
System
Options
: Select
Picture Settings
Initial
Setup
ENTER
: Enter
RETURN
Information
: Back
MENU
: Exit
Picture
Settings
Menu
Picture Settings
AV MODE (Changing Pic.Quality)
AV MODE (Changing Pic.Quality)
[STANDARD]
[STANDARD]
OPC
OPC
[On:Display]
Backlight
[ b5] a16
Contrast
[b30]
0
Brightness
[
0] a30
Color
[ b2] a30
Tint
[
0] a30
Sharpness
[ b2] a10
Backlight
[ b5] a16
b16
Contrast
[b30]
b40
0
Brightness
[ 0] a30
b30
Color
[ b2] a30
b30
Tint
[ 0] a30
b30
Sharpness
[ b2] a10
b10
Advanced
Advanced
Reset
Reset
b16
b40
b30
b30
b30
b10
1 Guide display
1
2
Press MENU to display the MENU screen.
1 Press c/d to select the desired menu.
2 Press a/b to select a specific adjustment item,
and then press ENTER.
• Additional related adjustment items may be
displayed. Press a/b to select the desired item.
3 Adjust the item while referring to the guide
display.
• Operations vary depending on the function or item.
Refer to the guide display corresponding to the
menu setting screen for button operations.
3 Press MENU to exit.
• This indicates the buttons that can be operated on the
displayed screen. The guide display varies depending
on the menu setting screen.
• The operations for some selected items may be displayed
in the operational guide bar at the bottom of the screen.
2 Item displayed in blue
• This indicates the item currently selected.
• Press ENTER to go to the adjustment screen for this item.
3 Item in brackets
• This indicates the current setting for the item.
4 Item displayed in white
• This indicates that the item can be selected.
5 Item displayed in gray
• This indicates that the item cannot be selected.
There are various reasons why the items cannot be
selected, but the main reasons are as follows:
—Nothing is connected to the selected input terminal.
—The function is not compatible with the current input signal.
• Menu options differ in the selected input modes, but the operating procedures are the same.
• The screens in the operation manual are for explanation purposes (some are enlarged, others cropped) and may vary slightly
from the actual screens.
• The order of explanations for each menu item in the following pages is not necessarily in accordance with the alignment of
the items on the screen.
LCFONT:
• This product is embedded with LC Font technology, which was developed by SHARP Corporation for clearly displaying easyto-read characters on LCD screens.
Menu Operation Buttons
Using the remote control
Use the following buttons on the remote control to
operate the menu.
Using the control panel of the TV
You can also operate the menu with the control panel
of the TV.
Button operations on the control panel correspond to
the ones on the remote control as shown below.
MENU:
MENU:
Press to open or close the menu screen.
a/b/c/d: Press to select a desired item on the screen or
adjust a selected item.
ENTER:
Press to go to the next step or complete the
setting.
RETURN: Press to return to the previous step.
MENU on the
remote control.
INPUT:
ENTER on the
remote control.
CHU/V: Cursor a/b
on the remote
control.
VOLk/l: Cursor c/d
on the remote
control.
27
LC-90LE745U_E.indb 27
2012/04/06 16:49:54
On-Screen Display Menu
Menu Items
• When AV MODE is set to "AUTO", part of the menu may not be displayed correctly or the setting range of the menu may be
changed.
• Some menu items may not be displayed depending on the selected input source.
Picture Settings
AV MODE
(Changing Pic.Quality) ........Pages 29 and 48
OPC ................................................ Page 29
Backlight ......................................... Page 29
Contrast .......................................... Page 29
Brightness ....................................... Page 29
Color ............................................... Page 29
Tint.................................................. Page 29
Sharpness ....................................... Page 29
Advanced ................................. Pages 29-30
C.M.S.-Hue ........................... Page 29
C.M.S.-Saturation ................. Page 29
C.M.S.-Value......................... Page 29
Color Temp. ......................... Page 30
Motion Enhancement ............ Page 30
Active Contrast ..................... Page 30
Gamma Adjustment .............. Page 30
Black Level............................ Page 30
Film Mode ............................. Page 30
Digital Noise Reduction ......... Page 30
Monochrome ........................ Page 30
Range of OPC ....................... Page 30
Reset .............................................. Page 29
Audio Settings
Auto Volume ................................... Page 31
Treble .............................................. Page 31
Bass................................................ Page 31
Balance ........................................... Page 31
3D Surround ................................... Page 31
Bass Enhancer ................................ Page 31
Clear Voice ...................................... Page 31
Reset .............................................. Page 31
Power Control
Audio Only ...................................... Page 32
Power Saving .................................. Page 32
No Signal Off ................................... Page 32
No Operation Off ............................. Page 32
System Options
View Option..............................Pages 33, 57
APPS .................................... Page 33
USB Operation Panel ............ Page 57
Home Network (DLNA)
Operation Panel .................... Page 57
View Mode ............................ Page 33
Freeze ................................... Page 33
Change Audio ....................... Page 33
Change CC ........................... Page 33
3D Setup ......................................... Page 49
AQUOS LINK Setup ........................ Page 62
Terminal Setting ................. Pages 33-34, 67
Audio Setup .......................... Page 33
PC input ................................ Page 67
Audio Select.......................... Page 67
Input Skip.............................. Page 34
Input Label ............................ Page 34
HDMI Setup .......................... Page 34
Output Select ........................ Page 34
Color System ........................ Page 34
Menu Design ................................... Page 34
Channel Selecting Effect ....... Page 34
Program Title Display ............ Page 34
Position ................................. Page 34
Caption Setup ....................... Page 34
Game Play Time .............................. Page 35
Operation Lock Out ......................... Page 35
Icon Light Up Setting ....................... Page 35
Demo Mode .................................... Page 35
Initial Setup
EZ Setup ......................................... Page 36
Language .............................. Page 36
Location & Time .................... Page 36
TV Location ........................... Page 36
Antenna & Cable/STB ........... Page 36
Air/Cable ............................... Page 36
CH Search ............................ Page 36
Network ................................ Page 36
Completed ............................ Page 36
Broadcasting Setup.................. Pages 36-37
CH Setup .............................. Page 36
Favorite CH ........................... Page 37
Antenna Setup-DIGITAL ........ Page 37
Internet Setup .............. Pages 58, 68, 71-72
Language ........................................ Page 37
DivX® Setup..................................... Page 58
Individual Setup ........................ Pages 37-39
Secret No. ............................ Page 37
Parental CTRL................ Pages 37-39
Wall Mount Audio Setup .................. Page 37
Reset .............................................. Page 37
Information
Identification .................................... Page 40
Digital Caption Info. ........................ Page 40
Software Update ...................... Pages 40-42
Manual Update .............. Pages 40-42
Auto Update Setting.............. Page 40
Netflix Help ...................................... Page 77
VUDU Help ...................................... Page 77
28
LC-90LE745U_E.indb 28
2012/04/06 16:49:55
On-Screen Display Menu
Picture Settings
AV MODE (Changing Pic.Quality)
Adjusts the picture to your preference with the
following picture settings.
Example
Picture
Settings
The audio and video settings can be changed to suit
the program or input content being watched.
Select from the following AV modes.
■ When the input source is TV, COMPONENT,
VIDEO 1 or 2:
Menu
AUTO/STANDARD/MOVIE/GAME/USER/DYNAMIC/
DYNAMIC(Fixed)
Picture Settings
■ When the input source is PC IN or HDMI 1 to 4:
AUTO/STANDARD/MOVIE/GAME/PC/USER/DYNAMIC/
DYNAMIC(Fixed)
AV MODE (Changing Pic.Quality)
[STANDARD]
OPC
[On:Display]
Backlight
[ b5] a16
Contrast
[b30]
0
Brightness
[ 0] a30
Color
[ b2] a30
Tint
[ 0] a30
Sharpness
[ b2] a10
b16
• The selectable items vary depending on the input source.
• For details of the selectable items in 3D mode, see page
48.
• You can select AV MODE by pressing AV MODE on the
remote control unit. See page 24 for details of AV MODE
settings.
b40
b30
b30
OPC Setting
b30
Automatically adjusts the brightness of the screen.
b10
Off: The brightness is fixed at the value set in "Backlight".
On: Automatically adjusts.
On:Display: Displays the OPC effect on the screen while
adjusting the brightness of the screen.
Advanced
Reset
1 Press MENU to display the MENU screen, and then
press c/d to select "Picture Settings".
2 Press a/b to select a specific adjustment item.
• Select "Advanced" and then press ENTER to set
"C.M.S.-Hue", "C.M.S.-Saturation", "C.M.S.-Value",
"Color Temp.", "Motion Enhancement", "Active
Contrast", "Gamma Adjustment", "Black Level", "Film
Mode", "Digital Noise Reduction", "Monochrome" or
"Range of OPC".
• When set to "On", the Optical Picture Control (OPC)
senses the surrounding light and automatically adjusts
the backlight brightness. Make sure nothing obstructs
the OPC sensor, which could affect its ability to sense
surrounding light.
• When set to "On:Display", OPC effect displays on the
screen while the OPC adjusts the screen brightness.
3 Press a/b(or c/d) to select the desired setting,
and then press ENTER.
4 Press MENU to exit.
Selected item
Backlight
c button
The screen dims
Contrast
Brightness
For less contrast
For less
brightness
For less color
intensity
Skin tones
become reddish
For less
sharpness
Color
Tint
Sharpness
OPC:
d button
The screen
brightens
For more contrast
For more
brightness
For more color
intensity
Skin tones
become greenish
For more
sharpness
• For resetting all Picture adjustment items to the factory
preset values, press a/b to select "Reset", press ENTER,
press a/b to select "Yes", and then press ENTER.
OPC:
Advanced Picture Settings
This TV provides various advanced functions for
optimizing the picture quality.
C.M.S.
(Color Management System)
Color tone is managed using the six-color adjustment
setting.
C.M.S.-Hue: This is a standard to adjust the color either
more reddish or more bluish in tone.
C.M.S.-Saturation: Increases or decreases the
saturation of a selected color.
C.M.S.-Value: A higher value makes the image brighter.
A lower value makes the image darker.
• For resetting all adjustment items to the factory preset
values, press a/b to select "Reset", and then press
ENTER.
29
LC-90LE745U_E.indb 29
2012/04/06 16:49:55
On-Screen Display Menu
Color Temp. (Color Temperature)
For a better white balance, use color temperature correction.
High:
Mid-High:
Middle:
Mid-Low:
Low:
White with bluish tone
White with reddish tone
White balance can be adjusted between a maximum of
+30 and a minimum of –30 for each color temperature.
R Gain (LO/HI)/G Gain (LO/HI)/B Gain (LO/HI)
■ Fine tuning the color temperature
To fine tune the color temperature, set "10 Point Setting"
to "On".
You can adjust the "Position" setting. Adjust the set color
temperature from +1 to +10.
White balance can be adjusted between a maximum of
+30 and a minimum of –30 for each color temperature.
• When "Position" is set to "10", you can adjust the white
balance between –30 and 0.
• For resetting all adjustment items to the factory preset
values, press a/b to select "Reset", and then press
ENTER.
Motion Enhancement
Use Motion Enhancement to view fast-action video
more clearly.
AquoMotion240: Turns the LED backlight on or off for
120Hz drive display.
120Hz High/120Hz Low: For obtaining a clearer image.
Off: Normal image.
• "Motion Enhancement" may cause image noise. If this
occurs, turn the function "Off".
• When AV MODE is set to "GAME" or "PC", or PC format is
being input, "Motion Enhancement" is not available.
Active Contrast
Automatically adjusts the image contrast according to
the scene.
On: Automatically adjusts the image contrast.
Off: No adjustment.
Gamma Adjustment
Adjusts the differences of picture tones between bright
parts and dark parts. The adjustment range of the
gamma can be set to a maximum of +2 and a minimum
of –2 by pressing c or d.
Black Level
Adjusts on-screen black level to your preferred level.
High: The black level gets brighter.
Low: The black level gets darker.
• "Black Level" is available for input signal from Composite
Video, Component 480i and analog broadcasts (air and
cable).
Film Mode (3:2 pull-down)
This function provides high-quality playback of images
originally encoded at 24 frames/second, such as films.
Advanced: Adjusts effect to reduce judder from film
contents. You can select a desired level of judder
reduction from 0 to +10.
Standard: Plays back images with equal display time for
each frame, reproducing movie theater experience.
Off: Normal viewing mode.
• "Film Mode" does not function depending on input signal
type.
• "Film Mode" does not function when you set AV MODE to
"GAME" or "PC".
• "Standard" does not function depending on input signal
type.
Digital Noise Reduction
Produces a clearer video image.
Auto: Automatically adjusts the level of noise reduction.
High/Middle/Low: You can select a desired level for
viewing a clearer video image.
Off: No adjustment.
• "Digital Noise Reduction" is not available when you set AV
MODE to "PC" or PC format is being input.
• When AV MODE is set to "GAME", "Auto" is not available.
Monochrome
For viewing a video in monochrome.
On: For viewing in monochrome.
Off: Normal color.
Range of OPC
The brightness level range of the OPC sensor's automatic
adjustments can be set according to your preferences.
The adjustment range of the OPC sensor can be set to
a maximum of +16 and a minimum of –16.
Max.: –15 through +16
Min.: –16 through +15
• The "Range of OPC" settings are active only when "OPC"
is set to "On".
• The maximum setting cannot be set to a smaller number
than the minimum setting.
• The minimum setting cannot be set to a bigger number
than the maximum setting.
• Depending on the brightness of the surrounding light, the
OPC sensor might not operate if the adjustment range is
small.
30
LC-90LE745U_E.indb 30
2012/04/06 16:49:55
On-Screen Display Menu
Audio Settings
Auto Volume
You can adjust the sound quality to your preference
with the following settings.
Example
Audio
Settings
High: Reduces the loudness gaps among different
sound sources strongly.
Menu
Audio Settings
Middle:
Auto Volume
Low: Reduces the loudness gaps among different
sound sources slightly.
[Off]
Treble
[ 0] a15
Bass
[ 0] a15
b15
b15
• The Audio Settings menu is grayed out when "Output
Select" is set to "Variable". (See page 34.)
Balance
[
0]
L
R
3D Surround
3D Surround
[Off]
The surround function produces Surround effect from
the speakers.
Bass Enhancer
[On]
Clear Voice
[Off]
Reset
1 Press MENU to display the MENU screen, and then
2
Different sound sources sometimes do not have the
same loudness level, such as a program and its
commercial breaks. The Automatic Volume Control
(Auto Volume) reduces this problem by equalizing
levels.
press c/d to select "Audio Settings".
Press a/b to select a specific adjustment item.
• Select "Auto Volume", "3D Surround", "Bass Enhancer"
or "Clear Voice", and then press ENTER to set each
item.
3 Press a/b (or c/d) to select the desired setting,
and then press ENTER.
3D Stadium: Reproduces lifelike experience of
excitements such that live sports or concert
performances in a stadium create.
3D Hall: Reproduces concert hall experience with realistic
live surround sound using measured reverberant sound
in the concert hall.
3D Movie: Reproduces movie theater experience
with realistic live surround sound using measured
reverberant sound in the movie theater.
3D Standard: Creates 3 dimensional surround sound
with detailed control of the signal phase.
Normal: Provides mild surround sound.
Off: Outputs the normal sound.
4 Press MENU to exit.
Selected item
Treble
Bass
Balance
c button
For weaker treble
For weaker bass
Decreases audio
from the right
speaker
d button
For stronger treble
For stronger bass
Decreases audio
from the left
speaker
• The Audio Settings menu is grayed out when "Output
Select" is set to "Variable". (See page 34.)
• For some discs, setup may be required on your BD/DVD
player. In this case, please refer to the operation manual of
your BD/DVD player.
Bass Enhancer
This function allows you to enjoy bass-enhanced sound.
• The Audio menu is grayed out when "Output Select" is set
to "Variable". (See page 34.)
• For resetting Audio adjustment items to the factory preset
values, press a/b to select "Reset", press ENTER, press
a/b to select "Yes", and then press ENTER.
On: The Bass Enhancer function is on.
Off: Normal sound.
• The Audio Settings menu is grayed out when "Output
Select" is set to "Variable". (See page 34.)
Clear Voice
This function emphasizes speech against background
noise for greater clarity.
• The Audio Settings menu is grayed out when "Output
Select" is set to "Variable". (See page 34.)
31
LC-90LE745U_E.indb 31
2012/04/06 16:49:55
On-Screen Display Menu
Power Control
Power control setting allows you to save energy.
Example
Menu
Power
Control
Power Control
Audio Only
Power Saving
[
Standard]
No Signal Off
[Enable]
No Operation Off
[Disable]
1 Press MENU to display the MENU screen, and then
2
press c/d to select "Power Control".
Press a/b to select a specific adjustment item,
and then press ENTER.
3 Press a/b (or c/d) to select the desired setting,
and then press ENTER.
4 Press MENU to exit.
• Skip this step for "Audio Only".
Audio Only
When listening to music from a music program, you
can turn the screen off and enjoy audio only.
On: Audio is output without screen image.
Off: Both screen images and audio are output.
• The screen image will return to normal when a button
(except those for audio adjustment, such as VOL, MUTE)
is pressed.
Power Saving
This function allows you to set the Power Saving level
in order to decrease the power consumption and
increase the backlight lifespan.
Standard: Optimizes power reduction based upon video
content. When set to "Standard", " " appears on the
screen.
Advanced: Optimizes power reduction based upon video
content and engages OPC. When set to "Advanced",
"
" appears on the screen.
Off: This function does not work.
• "Power Saving" does not function when you set AV MODE
to "AUTO" or "DYNAMIC (Fixed)".
• You cannot select a different Power Saving item for each
AV MODE.
When "Power Saving" is set, the "OPC" settings for all AV
Modes will automatically change.
—If you set "OPC" to "On" when "Power Saving" is set to
"Standard", then the "Power Saving" setting will change
to "Advanced".
—When you change the "Power Saving" setting from
"Advanced" to "Off" or to "Standard", "OPC" will be set
to "Off".
—"AUTO" and "DYNAMIC (Fixed)" will remain set to "Off".
• When "Power Saving" is set to "Standard" or "Advanced",
the Power Saving leaf icon appears to the left of "OPC" in
the Picture Settings menu screen.
• "Power Saving" is not available when the TV is in 3D mode.
No Signal Off
This function allows the TV to automatically shut the
power down when there is no signal received.
Enable: The power will automatically shut down if there is
no signal for 15 minutes.
Disable: This function does not work.
A confirmation screen appears.
Yes: The setting will be changed.
No: The setting will not be changed.
• When it is 5 minutes before the power shuts down, the
remaining time will start to keep appearing every minute.
• When a TV program finishes, this function may not operate.
No Operation Off
This function allows the TV to automatically shut the
power down when there is no operation.
Enable: The power will automatically shut down if there is
no operation for 3 hours.
Disable: This function does not work.
A confirmation screen appears.
Yes: The setting will be changed.
No: The setting will not be changed.
• When it is 5 minutes before the power shuts down, the
remaining time will start to keep appearing every minute.
32
LC-90LE745U_E.indb 32
2012/04/06 16:49:55
On-Screen Display Menu
System Options
Example
System
Options
Menu
System Options
View Mode
This function changes the screen size.
Select "View Option" on the menu to display the View
Mode menu screen.
The View Mode menu varies depending on the input source.
• You can select View Mode by pressing VIEW MODE on
the remote control unit.
— See page 26 for adjusting the video being input from a
TV, other audiovisual equipment, USB-Video, DLNAVideo or Internet applications.
—See page 66 for adjusting the video being input from a PC.
View Option
3D Setup
AQUOS LINK Setup
Freeze
Allows you to capture and freeze a moving image that
you are watching.
Terminal Setting
Menu Design
Operation Lock Out
[Off]
Icon Light Up Setting
[On]
Demo Mode
• You can select Freeze by pressing FREEZE on the remote
control unit. See page 23 for details of Freeze function.
Change Audio
Allows you to change the audio when multiple audio is
available for the program you are watching.
• You can change Audio by pressing AUDIO on the remote
control unit. See pages 24 to 25 for details of Audio
function.
Change CC
Allows you to change the Closed Caption display.
Select "Change CC" on the menu to display the Closed
Caption information.
1 Press MENU to display the MENU screen, and then
press c/d to select "System Options".
2 Press a/b to select a specific adjustment item and
then press ENTER.
3 Press a/b (or c/d) to select the desired setting,
4
and then press ENTER.
Press MENU to exit.
View Option
These functions are useful for adjusting the audio
and video settings. The View Option functions can be
operated with the remote control unit.
APPS
The application window can be displayed by selecting
"APPS" on the MENU screen.
• You can display the application window by pressing
SmartCentral on the remote control unit. (See page 24.)
• The information displayed varies depending on the program
you are watching.
• You can change Closed Caption by pressing CC on the
remote control unit. See page 25 for details of Closed
Caption function.
Terminal Setting
Audio Setup
You can output digital audio to an AV amplifier or
similar device whose DIGITAL AUDIO INPUT terminal
is connected to the DIGITAL AUDIO OUTPUT terminal
on the TV. Please select an audio output format
compatible with the audio format of the program you
are watching and the equipment connected.
PCM: For connecting to equipment that does not support
Dolby Digital. The same audio (main, sub, or main/sub)
as the audio of the program being viewed is output.
2-channel audio with a sampling rate of 48 kHz or less
is output as linear PCM audio.
Bitstream: For connecting to an audio system that
supports Dolby Digital. Audio is output through both
the main and sub channels.
• Analog channel audio and video input audio are output in
PCM mode even when "Bitstream" is selected.
• PCM digital input signals are output in PCM mode even
when "Bitstream" is selected.
33
LC-90LE745U_E.indb 33
2012/04/06 16:49:55
On-Screen Display Menu
Input Skip
This setting allows you to skip the TV, HDMI or PC IN
Input ("TV", "PC IN", "HDMI 1", "HDMI 2", "HDMI 3"
and "HDMI 4") on the Input Selection operation.
Yes: Skips the input.
No: Does not skip input.
Input Label
Lets you set the input terminal displayed when using
the INPUT list or channel display. Press a/b/c/d to
select the new name for the input mode.
• Using the software keyboard, you can enter up to
10 characters for text. (See page 73.)
Menu Design
Channel Selecting Effect
You can select whether to use transition effects when
changing channels.
Yes: A transition effect is used when the channel is
changed.
No: No function.
• In some cases, "Channel Selecting Effect" does not work.
• You cannot change labels if the input source is TV, Home
Network (DLNA) or USB.
Program Title Display
Select the CH display when changing channels for
digital broadcasting.
HDMI Setup
To watch an HDMI or PC IN equipment image, select
"HDMI 1", "HDMI 2", "HDMI 3" or "HDMI 4" from the
INPUT list using INPUT on the remote control unit or
on the TV.
Position
For adjusting a picture's horizontal and vertical
position.
Auto View:
Enable: To use View Mode based on signal
recognition, including an HDMI signal.
Disable: No function.
Yes: "Program Info." displays.
No: "Program Info." does not display.
H-Pos.: Centers the image by moving it to the left or
right.
V-Pos.: Centers the image by moving it up or down.
Output Select
Allows you to select what controls the audio output.
• For resetting adjustments to the factory preset values,
press a/b to select "Reset", and then press ENTER.
• When connecting a PC to the HDMI terminal, the image
position will be automatically adjusted. It cannot be
manually adjusted.
• The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
position-setting screen.
• Adjustments are stored separately according to input
source.
• "Position" does not work when USB mode, Home Network
(DLNA) mode or an Internet application is used.
• You may not be able to adjust the position while in 3D
mode.
Color System
Select the video signal system compatible with your
equipment from the list below:
Caption Setup
This function allows you to adjust the closed caption
screen appearance to suit your preference. You can
adjust 7 items: "Caption Size", "Font Style", "Foreground
Color", "Foreground Opacity", "Background Color",
"Background Opacity" and "Character Edge".
• Refer to your external equipment operation manual for the
signal type.
• When connecting a DVI-HDMI conversion adapter/cable to
the HDMI terminal, the image may not come in clearly.
Fixed: Sound via speaker is adjusted with VOLk/l on
the remote control unit or on the TV.
Sound via the AUDIO OUT terminal is not adjustable
and outputs at a consistent level.
Variable: Sound via the AUDIO OUT terminal is adjusted
with VOLk/l on the remote control unit or on the TV.
Sound via speaker is muted.
Auto/NTSC/PAL-M/PAL-N
• "Color System" can only be set for the VIDEO 1 or 2.
• If you have already set the Secret No., input the 4-digit
secret number here. See page 37 for setting a secret
number.
Example:
Selectable items available for "Font Style".
Default: The font specified by broadcasting station or
default font.
Type 0: Proportional font used in the MENU screen.
Type 1: Monospaced with serifs.
Type 2: Proportionally spaced with serifs.
Type 3: Monospaced without serifs.
Type 4: Proportionally spaced without serifs.
Type 5: Casual font type.
Type 6: Cursive font type.
Type 7: Small capitals.
• For resetting adjustments to the factory preset values,
press a/b to select "Reset", and then press ENTER.
• The default value depends on the broadcasting station.
34
LC-90LE745U_E.indb 34
2012/04/06 16:49:56
On-Screen Display Menu
Game Play Time
This function displays the elapsed game time so you
do not lose track of the time. To display the elapsed
time, select "GAME" for the AV MODE before starting
the game.
On: The elapsed time is displayed every 30 minutes when
you switch to GAME mode in external input mode.
Off: No adjustment.
Operation Lock Out
This function locks the operation buttons on the TV
and the remote control.
Off: No adjustment.
RC Control Lock: All buttons on the remote control are
locked.
Button Control Lock: All buttons on the TV, except
POWER, are locked.
When “RC Control Lock” or “Button Control Lock” is
selected, a confirmation screen appears.
Yes: Locks the operation buttons.
No: No adjustment.
• To unlock the buttons on the remote control by using the
control panel of the TV (see page 27):
1 Press MENU to display the MENU screen, press
VOLk/l to select "System Options", and then press
INPUT.
2 Press CHU/V to select "Operation Lock Out", and
then press INPUT.
3 Press CHU/V to select "Off", and then press INPUT.
4 Press MENU to exit.
• To unlock the buttons on the TV, press MENU on the
remote control, and then select "Off" in "Operation Lock
Out".
Icon Light Up Setting
When this function is set to "On", the LED on the front
of the TV turns on.
• The LED lights white in 2D mode.
• The LED lights blue in 3D mode.
• "On" is the factory preset value. If you want to turn off the
LED, set the function to "Off".
Demo Mode
You can select the image from several types of demo
mode.
AquoMotion240/SmartCentral/Feature Demo/Auto
Play
If you have selected "Auto Play", you need to select the
desired playback type(s), and then set the playback time.
Continuous: Plays demos continuously.
10 min.: Plays demos every 10 minutes.
20 min.: Plays demos every 20 minutes.
• This function will be canceled when you press EXIT on the
remote control unit.
• When "Demo Mode" is set to "Feature Demo", pressing
FREEZE pauses/restarts demo.
• "Demo Mode" may not be selected depending on input
signal type or application status.
• "Demo Mode" may be automatically canceled depending
on input signal type.
35
LC-90LE745U_E.indb 35
2012/04/06 16:49:56
On-Screen Display Menu
Initial Setup
Example
Initial
Setup
Menu
Antenna & Cable/STB: Select the type of connection
you will use to watch TV.
Air/Cable: Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable".
CH Search: Channel auto search makes the TV look for
all channels viewable in the set area.
• If "Cable" is selected for Antenna setting, scrambled
channels are removed after the Channel search has been
completed.
Initial Setup
EZ Setup
Network: When you connect to the Internet on the TV,
confirm the connection method and make adjustments.
Broadcasting Setup
Internet Setup
Language
[English]
DivX® Setup
• Wireless LAN connection is possible only when the WPS
(push button) method is used. If any other method is used,
make settings by Initial Setup > Internet Setup > Network
Setup. (See page 71.)
Completed: The settings confirmation screen is displayed.
Confirm the information displayed on the screen.
Individual Setup
Wall Mount Audio Setup
[No]
Reset
1 Press MENU to display the MENU screen, and then
press c/d to select "Initial Setup".
2 Press a/b to select a specific adjustment item,
and then press ENTER.
• When you select "EZ Setup", "CH Setup", "Parental
CTRL" or "Reset", you can enter the 4-digit secret
number here. See page 37 for setting a secret number.
3 Press a/b (or c/d) to select the desired setting,
and then press ENTER.
4 Press MENU to exit.
EZ Setup
You can run EZ Setup again, even after setting up the
preset channels.
Language: Select from among 3 languages (English,
French and Spanish).
Location & Time: Make settings for the country, area
and time zone where you use the TV.
Select your country: Select either "United States", "Canada"
or "Mexico".
Select your time zone: Select your time zone. The available
settings differ depending on the selected country.
Select DST (Daylight Savings Time): Select "Auto", "Manual"
or "Off".
TV Location: Select "Home" or "Store" for the location
where you plan to install the TV.
Home: "Power Saving" is set to "Advanced", and AV MODE is
set to "STANDARD".
Store: "Power Saving" is set to "Off" and AV MODE is set to
"DYNAMIC (Fixed)". Picture Reset and Feature Demo can be set.
Picture Reset: AV MODE will be set to "DYNAMIC (Fixed)"
regardless of whether Picture Reset is "On" or "Off". If you
select "On", AV MODE will be reset to "DYNAMIC (Fixed)"
if there is no operation for 30 minutes. When "Off" is
selected, AV MODE will be set to "DYNAMIC (Fixed)".
Feature Demo: When "On" is selected, after all the settings
are completed, the Feature Demo screen is displayed if
there is no operation for several minutes.
• See Initial Installation on pages 19 to 22 for setting each item.
• If no channel is found, confirm the type of connection
made with your TV and try "EZ Setup" again.
• If you select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
Broadcasting Setup
CH Setup
If Initial Installation does not memorize all the channels
in your region, follow the instructions below to manually
memorize the channels.
Air/Cable: Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable".
CH Search: Channel auto search makes the TV look for
all channels viewable in the set area.
CH Memory: You can select the channels to skip in each
ANALOG (Air), ANALOG (Cable), DIGITAL (Air) and
DIGITAL (Cable).
On: Skips channels. (Channel selection disabled using CH
U/V.)
Off: Does not skip channels. (Channel selection enabled using
CHU/V.)
Remove Scrambled CH: This function makes the TV
look for and then delete digital cable channels that
are scrambled and so unavailable in the set area. The
process may take more than 20 minutes.
Yes: Starts to remove scrambled channels.
No: This function does not work.
• See Initial Installation on pages 19 to 22 for setting each item.
• If no channel is found, confirm the type of connection
made with your TV and try channel search again.
• If you select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
36
LC-90LE745U_E.indb 36
2012/04/06 16:49:56
On-Screen Display Menu
Favorite CH (Favorite Channel Setting)
This function allows you to program 4 favorite
channels, in 4 different categories. By setting the
favorite channels in advance, you can select your
favorite channels easily.
To register your favorite channel:
Select "Register" and then press ENTER. Press a/b/c/
d to select the position in the category, and then press
ENTER to register.
To delete your favorite channel:
Select "1 Data Clear" and then press ENTER. Press
a/b/c/d to select the channel you want to delete, and
then press ENTER. Select "Yes" and then press ENTER.
To delete all the favorite channels, select "All Data Clear".
• Before setting the channel, select the channel you want to
register as a favorite channel.
• You can display the "Favorite CH" screen by pressing
FAVORITE CH on the remote control.
Antenna Setup-DIGITAL
In order to receive digital air broadcasts, you need
a digital broadcast antenna. You can confirm the
antenna configuration through the "Antenna SetupDIGITAL" screen. If necessary, adjust the direction of
the antenna to obtain the maximum signal strength.
Signal Strength: The signal strength of DIGITAL channel
is displayed. The signal information is based on the
current channel.
Channel Strength: Input the 2-digit channel number
to check the signal strength of the selected channel.
Make sure the signal is strong enough for each
channel.
• This function is available for DIGITAL (Air) only.
Language
You can also select a language from the Initial Setup
menu. Select from among 3 languages: English,
French and Spanish.
Wall Mount Audio Setup
This selects the optimal audio for the program you are
currently watching even when the TV is mounted to a
wall.
Yes: Selects the optimal audio.
No: No adjustment.
Reset
If complex adjustments are made and the settings
cannot be restored to normal, you can reset the
settings to the factory preset values.
• If you have already set the Secret No., input the 4-digit
secret number here.
The Channel Setup settings will not be changed.
The Language settings will not be changed.
The Secret number settings will not be changed.
The TV Location settings will not be changed.
•
•
•
•
Individual Setup
Secret No.
Allows you to use a secret number to protect certain
settings from being accidentally changed.
IMPORTANT:
Three conditions must be met to enable the V-Chip (see
pages 38 to 39):
1. Secret No. is registered.
2. V-Chip/V-Chip (DTV Only) settings have been made.
• The “V-Chip (DTV Only)” will only be selectable when a new
rating system can be downloaded via digital broadcasting in the
U.S.
3. "Status" is set to "On".
■ Setting the Secret No.
You can set and change the secret number by using
0-9.
Yes: Changes or sets the Secret No.
No: The confirmation screen to clear the Secret No.
appears when the Secret No. has been set. When the
Secret No. has not been set, the previous screen will
be displayed.
■ Secret No. Clear
You can clear your secret number.
Yes: Your secret number is cleared.
No: Your secret number is not cleared.
• As a precautionary measure, make a note of your secret
number and keep it in a familiar place.
• If the secret number is cleared, the Status setting
automatically sets to "Off". "V-Chip" and "Status" will not
be selectable from the menu.
Parental CTRL
(Parental Control Setting)
Status
Used to enable or disable the parental control function.
This function will not be selectable from the menu if
you do not first configure your secret number.
On: Enables Parental CTRL.
Off: Disables Parental CTRL.
37
LC-90LE745U_E.indb 37
2012/04/06 16:49:56
On-Screen Display Menu
V-Chip
V-CHIP is an electronic filtering device built into your
TV. This tool gives parents a great degree of control
over broadcasts accessed by their children. It allows
parents to select programs judged suitable for child
viewing while blocking ones judged not suitable. It
does so automatically once you activate the V-CHIP
feature in your TV. "V-Chip" and "Status" will not be
selectable from the menu if you do not first configure
your secret number.
• The U.S. has two rating systems for viewing content: TV
Parental Guidelines and movie ratings.
• The TV Parental Guidelines work in conjunction with the
V-CHIP to help parents screen out inappropriate television
shows from their children.
• Movie ratings are used for original movies rated by the
Motion Picture Association of America (MPAA) as watched
on cable TV and not edited for television. The V-CHIP can
also be set to block MPAA-rated movies.
• The setting automatically enters "Block" for any ratings
below your selection.
• If Status is not set to "On", the configuration settings will
not work.
■ TV Parental Guidelines
Example
MPAA
TV Guidelines
TV-Y
Can. English Ratings
TV-Y7
Can. French Ratings
TV-G
L
TV-PG
S
D
TV-14
V
TV-MA
FV
NONE
Press a/b to adjust the item to your desired position.
" " indicates the item is blocked. Press MENU to exit.
Suggested age
TV-Y: All children.
TV-Y7: Directed to older children.
TV-G: General audience.
TV-PG: Parental Guidance suggested.
TV-14: Parents strongly cautioned.
TV-MA: Mature audience only.
Example
MPAA
■ MPAA (Voluntary movie rating system)
Example
MPAA
TV Guidelines
G
Can. English Ratings
PG
Can. French Ratings
PG-13
TV Guidelines
TV-Y
Can. English Ratings
TV-Y7
Can. French Ratings
TV-G
L
TV-PG
S
X
NONE
Press a/b to adjust the item to your desired position.
" " indicates the item is blocked. Press MENU to exit.
G: General audiences. All ages admitted.
PG: Parental guidance suggested. Some material may not be
suitable for children.
PG-13: Parents strongly cautioned. Some material may be
inappropriate for children under 13.
R: Restricted. Under 17 requires accompanying parent or
adult guardian (age varies in some jurisdictions).
NC-17: No one 17 and under admitted.
X: X is an older rating that is unified with NC-17 but may be
encoded in the data of older movies.
• Voluntary movie rating system only uses an age-based
rating.
TV-14
V
TV-MA
FV
NONE
R
NC-17
D
When setting an individual content-based rating item:
1 Press d or ENTER to access blocked content
items from the currently selected age-based rating
item.
2 Press a/b to select an individual item, and then
press ENTER to unblock it (" " is removed). Repeat
the same steps for the other items.
3 Press c or RETURN to register after all individual
content rating items are set.
Content
FV: Fantasy violence.
V: Violence.
S: Sexual situation.
L: Adult language.
D: Sexually suggestive dialog.
Rating
Content
FV
V
S
L
D
TV-Y
TV-Y7
Suggested
age
TV-G
TV-PG
TV-14
TV-MA
: The content rating can be set, but this rating is not
normally broadcast by TV stations.
: Content rating can be set.
38
LC-90LE745U_E.indb 38
2012/04/06 16:49:56
On-Screen Display Menu
Canadian Rating Systems (Canadian English ratings
and Canadian French ratings)
• The TV rating systems in Canada are based on the
Canadian Radio-Television and Telecommunications
Commission (CRTC) policy on violence in television
programming.
• While violence is the most important content element to
be rated, the structure developed takes into consideration
other program content like language, nudity, sexuality and
mature themes.
• When setting the V-CHIP on the Canadian system you
can choose either the Canadian English ratings or the
Canadian French ratings.
■ Canadian English Ratings
Example
MPAA
TV Guidelines
E
Can. English Ratings
C
Can. French Ratings
C8+
G
PG
14+
18+
NONE
Press a/b to adjust the item to your desired position.
" " indicates the item is blocked. Press MENU to exit.
E: Exempt: Includes news, sports, documentaries and other
information programming; talk shows, music videos, and
variety programming.
C: Children: Intended for younger children under the age of 8
years. Pays careful attention to themes that could threaten
their sense of security and well-being.
C8+: Children over 8 years old: Contains no portrayal
of violence as the preferred, acceptable, or only way
to resolve conflict; nor encourage children to imitate
dangerous acts which they may see on the screen.
G: General: Considered acceptable for all age groups.
Appropriate viewing for the entire family, contains very little
violence, physical, verbal or emotional.
PG: Parental Guidance: Intended for a general audience, but
may not be suitable for younger children (under the age of 8)
because it could contain controversial themes or issues.
14+: Over 14 years: Could contain themes where violence
is one of the dominant elements of the storyline, but it
must be integral to the development of plot or character.
Language usage could be profane and nudity present
within the context of the theme.
18+: Adults: Intended for viewers 18 years and older and
might contain depictions of violence, which while related to
the development of plot, character or themes, are intended
for adult viewing. Could contain graphic language and
portrayals of sex and nudity.
■ Canadian French Ratings
Example
MPAA
TV Guidelines
E
Can. English Ratings
G
Can. French Ratings
8ans+
13ans+
16ans+
18ans+
NONE
Press a/b to adjust the item to your desired position.
" " indicates the item is blocked. Press MENU to exit.
E: Exempt programming.
G: General: All ages and children, contains minimal direct
violence, but may be integrated into the plot in a humorous
or unrealistic manner.
8ans+: General but inadvisable for young children: May
be viewed by a wide public audience, but could contain
scenes disturbing to children under 8 who cannot
distinguish between imaginary and real situations.
Recommended for viewing with parent.
13ans+: Over 13 years: Could contain scenes of frequent
violent scenes and therefore recommended for viewing with
parent.
16ans+: Over 16 years: Could contain frequent violent scenes
and intense violence.
18ans+: Over 18 years: Only for adult viewing. Could contain
frequent violent scenes and extreme violence.
■ How to temporarily release the V-CHIP BLOCK
When the V-CHIP BLOCK is working and censors a
broadcast, "V-CHIP HAS BEEN ACTIVATED." displays.
1 Press ENTER while the V-CHIP is working, and
then the secret number setting menu displays.
2 Input the 4-digit secret number by using 0–9. At this
time V-CHIP BLOCK temporarily releases.
■ Reactivating the temporarily released V-CHIP
BLOCK
You can reactivate the temporarily released V-CHIP
BLOCK as shown below.
• Select "Status" setting from the Parental CTRL menu to
reactivate BLOCK. (See page 37.)
• Select "V-Chip" setting ("MPAA", "TV Guidelines", "Can.
English Ratings" or "Can. French Ratings") from the
Parental CTRL to reactivate BLOCK. (See pages 38 to 39.)
• Switch off the TV power.
• Performing any of the three above will activate the V-CHIP
BLOCK.
39
LC-90LE745U_E.indb 39
2012/04/06 16:49:56
On-Screen Display Menu
Information
2 Press a/b to select “Software Update”, and then
press ENTER.
Example
Information
Menu
• If you have already set the Secret No., go to step 3.
Example
Menu
Information
Information
Information
Identification
Identification
Digital Caption Info.
Digital Caption Info.
Software Update
Software Update
Netflix Help
VUDU Help
1 Press MENU to display the MENU screen, and then
2
3
4
press c/d to select "Information".
Press a/b to select a specific adjustment item,
and then press ENTER.
Press a/b (or c/d) to select the desired setting,
and then press ENTER.
Press MENU to exit.
Identification
The current version of the TV software is displayed.
Digital Caption Info.
(Digital Caption Information)
This function allows viewing of digital closed caption
information for the digital broadcast program being viewed.
• This list is not displayed for analog broadcasts or external
input audio/video.
• This information is not included in CC1, CC2, Text1, or
Text2, and is not displayed in a list.
Software Update
This is used to upgrade the system software to
enhance the TV functions.
3 Input the 4-digit secret number by using 0-9.
Software Update
Enter your Secret No.
4 Press a/b to select “Manual Update” or “Auto
Update Setting”, and then press ENTER.
• The operations thereafter vary depending on the setting.
Manual Update
Select the method for manually updating the software.
USB Update: Updates the software using a USB memory
device containing the update file. (See pages 41 to 42.)
Network Update: Downloads the update file via the
network and then updates the software. (See page 41.)
• A broadband connection and Internet Setup are required to
update the software using the network. (See pages 70 to
72.)
• It may take time to access and download the update
depending on the Internet connection and other factors.
Auto Update Setting
When the TV is on, or when an Internet application
is being accessed, this function enables the TV
to connect to the network and check for updates
automatically.
Yes: Enables Auto Update Setting.
No: Disables Auto Update Setting.
When an update is available, a message is displayed.
Press c/d to select "Yes", and then press ENTER to
display the download screen. (See page 41.)
1 Press MENU to display the MENU screen, and then
press c/d to select “Information”.
Yes
No
• This function does not work when a broadband connection
or Internet Setup is not available.
• A message may also be displayed when an application is
running.
The message varies depending on the application.
40
LC-90LE745U_E.indb 40
2012/04/06 16:49:56
On-Screen Display Menu
■ Updating the Software via the Network
1 Press a/b on the Manual Update screen to select
"Network Update", and then press ENTER.
• The TV connects to the network and checks for updates.
• To cancel, press ENTER.
Connecting to Internet..
Checking for the latest software version..
Accessing..
Abort
CAUTION
• Do not unplug the AC cord while the software is
being updated.
4 When the software is successfully updated, a
screen is displayed indicating that the update
process is completed.
A screen indicating that the update is completed
is displayed. 4 seconds later, the TV restarts
automatically.
Software update is complete.
2 The current version of the TV and the latest version
Update Version
of software are displayed. To update the TV
software, select “Yes”, and then press ENTER.
Latest software version has been found.
A software update is available.
Proceed with update?
XXXXXXXX
• If the software was not updated successfully, check the
broadband connection and Internet Setup, and then try
updating the software again.
Current Version
Failed to complete update.
Please retry from Software Update menu.
XXXXXXXX
Latest Version
XXXXXXXX
OK
Estimated Update Time
XX
Update time may change depending on the network environment
Yes
No
• When a server connection cannot be established or an
update is not available, a message is displayed.
If a server connection cannot be established, check the
broadband connection and Internet Setup.
Cannot reach the server.
Check the network settings and try again.
OK
■ Updating the Software with a USB Memory Device
To check for the availability of a software update, visit
http://www.sharpusa.com/products/support/. If you
have any questions, please
call 1-800-BE-SHARP (800-237-4277).
CAUTION
• Do not remove the USB memory device or unplug
the AC cord while the software is being updated.
• Be sure to properly follow the whole procedure
described below, step by step. Otherwise, for
example, the TV cannot read the data in the USB
memory device and software updating will fail.
1 Insert the USB memory device with the update file
The TV does not need to be updated.
into the USB 1 or USB 2 terminal on the TV.
• When you update the software, use only one USB
terminal. Either USB 1 or USB 2 is usable.
OK
3 After the update file is downloaded, the software
update process begins.
Downloading the latest software..
Update Version
XXXXXXXX
30%
Abort
Updating to the latest software..
or
Update Version
XXXXXXXX
50%
Remote control operation is disabled during update process.
Do not unplug AC cord.
2 Press a/b on the Manual Update screen to select
"USB Update", and then press ENTER.
41
LC-90LE745U_E.indb 41
2012/04/06 16:49:57
On-Screen Display Menu
3 Press ENTER to start checking the data in the USB
memory device.
5 To update the TV software with the update file,
select “Yes”, and then press ENTER.
Software update file is detected
in the USB memory device.
Start update?
Insert the USB memory device
containing the software update file.
Current Version
Update Version
: UXXXXXX1
: UXXXXXX2
OK
Yes
No
4 During the data checking, “Checking” blinks.
Example
Now checking the data
in the USB memory device.
Now updating
Update Version
: UXXXXXX2
Checking
30%
Remote Control operation is disabled during Update process.
• The current version of the TV software and the version
of the update file on the USB memory device are
displayed.
Example
Software update file is detected
in the USB memory device.
Start update?
Current Version
Update Version
CAUTION
• Do not remove the USB memory device or unplug
the AC cord while the software is being updated.
6 When the software is successfully updated, a
: UXXXXXX1
: UXXXXXX2
Yes
Do not unplug AC cord.
No
screen is displayed indicating that the update
process is completed.
After this screen is displayed, the TV automatically
turns off and then turns on again.
Example
• If the USB memory device is not properly installed or
the correct update file cannot be found on the USB
memory device, an error message is displayed.
Check the file on the USB memory device, and then
reinsert the USB memory device correctly.
Software update is complete.
Update Version
: UXXXXXX2
OK
Software update file is not detected in the USB memory device.
Confirm that you have transferred the file
to the USB memory device and retry software update.
• If the update has failed, check the file in the USB
memory device and try Software Update again.
OK
Failed to complete update.
Retry Software Update.
If system Update fails again,
contact the customer service center.
There is more than one software file in the USB memory device.
Confirm that only the software update file is
in the USB memory device.
Update Version
: UXXXXXX2
OK
OK
7 After the screen shown below is displayed, press
ENTER.
System software was
successfully updated.
Remove the USB memory device.
OK
8 Remove the USB memory device.
42
LC-90LE745U_E.indb 42
2012/04/06 16:49:57
Enjoying 3D Image Viewing
You can use special 3D Glasses to watch 3D-supported images on this TV.
• You can enjoy 3D movies on this TV by viewing the movie through SHARP 3D Glasses supplied with the TV or through
optional 3D Glasses sold separately.
• To produce 3D images, liquid crystal shutters in the 3D Glasses alternately open and close imperceptibly fast to exactly
match alternating left and right video images displayed by the TV.
• Not all consumers can experience and enjoy 3DTV. Some people suffer from stereo blindness which prevents them from
perceiving the intended depth of 3D entertainment. Also, some people who watch 3D programming may experience initial
feelings of motion sickness as they adjust to the picture. Others may experience headaches, eye fatigue or motion sickness.
Some viewers might also experience epileptic seizures. Like a roller coaster, the experience is not for everyone.
CAUTION
• The 3D Glasses are precision equipment. Handle them with care.
• Improper use of the 3D Glasses or failure to follow these instructions can result in eye strain.
• If you experience dizziness, nausea, or other discomfort while viewing 3D images, immediately discontinue use
of the 3D Glasses. Using the 3DTV with incompatible 3D broadcasts or software can make images appear blurry
or create overlapping images.
• When viewing 3D images continuously, be sure to take a break periodically to prevent eye strain.
• If you are nearsighted or farsighted or have astigmatism or a different level of eyesight between the left and right
eyes, you should take the necessary steps, such as wearing eyeglasses, to correct your eyesight before viewing
3D images. The 3D Glasses can be worn over eyeglasses.
• When viewing 3D images, keep the 3D Glasses horizontally level with the TV screen. If you tilt the 3D Glasses
with respect to the TV screen, the images viewed by the left and right eyes may appear significantly different or
images may appear overlapping.
• View 3D images at the appropriate distance from the TV screen. The recommended distance is three times the
effective height of the TV screen.
Examples of recommended distances:
90-inch screen: Approx. 11.2 ft (3.4 m)
Viewing should not be done closer than the recommended distance.
• Be careful of your surroundings when viewing 3D images. When you view 3D images, objects may appear
closer or farther than they are. This may cause you to misjudge the distance and possibly result in injury if you
accidentally hit the screen or surrounding objects.
• The 3D Glasses are not recommended for people aged less than 6.
• When children are viewing 3D images, be sure a parent or guardian is present. Monitor children viewing 3D
images, and if they show signs of discomfort, immediately discontinue use of the 3D Glasses.
• People with a known history of photosensitivity and people with heart problems or poor health should not use
the 3D Glasses. This can worsen existing health conditions.
• Do not use the 3D Glasses for other purposes (such as general eyeglasses, sunglasses, or protective goggles).
• Do not use the 3D function or 3D Glasses while walking or moving around. This may result in injuries due to
running into objects, tripping, and/or falling.
• When using the 3D Glasses, take care not to accidentally strike the TV screen or other people. Viewing 3D images may
cause you to misjudge the distance to the TV screen and accidentally strike the screen, resulting in possible injury.
• It is recommended that you do not view 3D images if you are sleep deprived or if you have been drinking alcohol.
Display Methods for 3D and 2D Images
Display method
2D ➝ 3D
3D mode
(using the 3D
Glasses)
Side by Side
Top and Bottom
2D mode
(without using
the 3D Glasses)
Example display
Description
• Converts normal 2D images into 3D images.
• Creates 3D images from 3D images displayed side
by side. The image is split into a left and right image,
and then the images are stretched and displayed
sequentially to create a 3D image.
• Creates 3D images from 3D images displayed on
the top and bottom. The image is split into a top and
bottom image, and then the images are stretched and
displayed sequentially to create a 3D image.
Side by Side ➝ 2D
• Creates 2D images from 3D images displayed side by
side. Only the left image is stretched and displayed. The
image does not appear in 3D.
Top and Bottom ➝ 2D
• Creates 2D images from 3D images displayed on the
top and bottom. Only the top image is stretched and
displayed. The image does not appear in 3D.
43
LC-90LE745U_E.indb 43
2012/04/06 16:49:57
Enjoying 3D Image Viewing
3D Glasses
Supplied Accessories for 3D Glasses
Make sure the following accessories are provided with the 3D Glasses. Two sets of 3D Glasses are provided.
3D Glasses
(×2)
Pages 44 to 48
Nose pad *1
(small ×2, large ×2)
Page 45
USB cable*2
(×2)
Page 45
Glasses case
(×2)
Cleaning cloth
(×2)
*1 Use the 3D Glasses nose pad as needed. The small nose pad is already attached.
*2 The supplied USB cable is a dedicated cable for the 3D Glasses. It does not operate when connecting with other USB
devices.
Use the supplied USB cable for recharging. When power is supplied to the glasses, use a commercially available USB cable.
• The illustrations above are for explanation purposes and may vary slightly from the actual accessories.
Part Names
5
1
2
3
4
1
2
3
4
5
Infrared receiver
Receives an infrared signal sent from the TV. The
3D Glasses turn off automatically after 10 minutes
if no signal is received from the TV.
USB terminal
This terminal is for recharging and supplying power.
3D/2D/OFF switch
This button switches between 2D, 3D and OFF
modes.
LED light
Blinks once every second when the battery power
is low.
Nose pad mount
The dedicated nose pad can be mounted here.
• Do not soil or apply stickers or block the infrared receiver.
Doing so may block signals from the TV and prevent the
3D Glasses from working correctly.
• Interference from other infrared communications equipment
may prevent you from viewing 3D images correctly.
44
LC-90LE745U_E.indb 44
2012/04/06 16:49:57
Enjoying 3D Image Viewing
Attaching the Nose Pad
Recharging the 3D Glasses
Attach either of the supplied nose pads as needed
(such as when the glasses do not fit properly). The
glasses come with a large and small nose pad.
When the battery power is low, the LED light blinks
one time per second. If the 3D Glasses battery is low,
you can recharge the 3D Glasses by connecting the
supplied USB cable to the TV and the USB terminal on
the 3D Glasses.
1 Turn off the TV, and then slide the switch on the 3D
Glasses to OFF.
2 Connect the cable shown at step 3 of this
procedure and then turn on the TV. Make sure the
cable is connected before turning on the TV.
1
1
2
Attaching the nose pad
Removing the nose pad
Using the 3D Glasses
• The LED light blinks approximately every two seconds,
and then starts recharging.
• When the LED light goes off, the recharge is complete.
It takes approximately 90 minutes to complete the
recharge.
• Insert the USB cable again if the LED light blinks on and
off once every 0.5 seconds. If it still does not respond,
inquire with a retail dealer or Sharp Authorized Service
Center.
3 After the recharge has completed, turn off the
TV, and then remove the USB cable from the 3D
Glasses.
Turning the Power On/Off
Slide the switch to 2D or 3D to turn on the power.
Slide the switch to OFF to turn off the power.
• When the battery power is low, the LED light blinks once
every second after the power is turned on.
Switching to 3D and 2D Mode
When viewing 3D images, you can slide the switch
between 2D and 3D modes. This is useful when
several people are viewing 3D images on the same TV
with some people wanting to watch in 3D and some
people wanting to watch in 2D.
■ Viewing 2D images
When you slide the switch to 2D while viewing 3D images,
the 3D images switch to 2D images.
■ Viewing 3D images
When you slide the switch to 3D while viewing 2D images,
the 2D images switch to 3D images.
Usage Range of the 3D Glasses
The 3D Glasses can be used by receiving an infrared
signal sent from the TV.
The 3D Glasses turn off automatically after 10 minutes
if no signal is received from the TV.
1 USB cable
(supplied accessory)
2 USB terminal
CAUTION
• Do not recharge while wearing the 3D Glasses.
• Be sure to turn on the TV when you recharge the 3D
Glasses. If the TV is turned off, the 3D Glasses may not
recharge.
• When you recharge the 3D Glasses, only connect the
supplied USB cable to a USB terminal on the TV.
• The battery will not recharge during usage with the USB
cable connected. The 3D Glasses battery will not be
recharged if the switch is set to 2D or 3D. To recharge the
battery, set the switch to OFF.
• Recharge the battery within the operating temperature
(50°F–104°F/10°C–40°C). The battery may not be able to
recharge outside of the operating temperature.
■ Operating range
From directly in front of the 3D infrared emitter on the TV:
approx.17 ft (5 m)
(within approx. 30° horizontally and 20° vertically)
45
LC-90LE745U_E_04.indd 45
2012/04/11 13:33:57
Enjoying 3D Image Viewing
Using the 3D Glasses with Power Supply
If you slide the switch to 3D or 2D after taking steps 1
and 2 in Recharging the 3D Glasses (see page 45),
you will be able to supply power to the 3D Glasses
while using the glasses (battery will not be recharged).
3 Pull the front casing outward with your fingers while
pulling the base of the right temple arm inward with
your fingers ( s ).
• Do not move around while wearing the 3D Glasses. Doing
so may result in getting your feet caught in the USB cable,
the TV falling or other accidents that may cause injury.
• When you supply power to the 3D Glasses, only connect
a USB cable (commercially available) to a USB terminal on
the TV.
• When you use the USB cable connecting the 3D Glasses,
be careful not to get your feet caught in the USB cable.
It may result in falling or other accidents that may cause
injury.
Removing the Battery for Recycling
The following instruction and procedure is provided
solely as a guide for the safe removal of the Li-ion
battery for proper disposal. This product is not
repairable. Do not attempt to replace the battery;
once the 3D Glasses are taken apart, they cannot
be reassembled or used again.
- Please take special care in handling small parts such as
screws specially around children that can accidentally
swallow them.
- Be very careful in handling the battery to prevent it from
leaking.
- Do not attempt to dismantle or puncture the battery.
- Do not use this battery for any other purpose. Recycle
properly after removing it from the 3D Glasses.
1 Front casing
2 Base
3 Right temple arm
4 Cut off the three cables of the rechargeable battery
unit one by one with a pair of scissors.
• There is the rechargeable battery unit inside 2 on the
right temple arm shown below.
• Insulate the tip of the removed rechargeable battery
cables, with material such as electrical tape, be sure
to insulate all three battery cable tips to prevent the
conductor wires from touching each other.
If you have any question regarding proper recycling
please call 1-800-822-8837 (see page 51 for more
details).
1 Pull out the nose pad with your fingers.
1 Right temple arm
2 Rechargeable battery unit
3 Rear casing
2 Remove the five screws with a Phillips screwdriver
(commercially available).
5 Pull out the entire rechargeable battery unit and
remove it from the rear casing.
• Used batteries should be handled in accordance with local
laws and regulations.
46
LC-90LE745U_E.indb 46
2012/04/06 16:49:58
Enjoying 3D Image Viewing
Viewing 3D Images
Switching from 3D to 2D Mode
4 Press 3D during the 3D mode.
Select “Yes” and press ENTER to switch to 2D
mode.
Yes
No
• Take off the 3D Glasses and turn off the power.
• The TV screen may temporarily become black when the TV
is trying to detect a 3D image signal and when switching
from 3D to 2D mode.
Receiving a 3D Image Signal That Can Be
Detected Automatically
The image signal may contain a 3D identification
signal. You can enable the TV to automatically detect
the 3D image type by selecting “System Options” > “3D
Setup” > “3D Auto Change” on the TV. (See page 49.)
1 When “3D Auto Change” is set to “Mode 1” or
“Mode 2”
• The 3D image type is detected automatically and the
appropriate 3D image is displayed.
Changed to 3D mode. Put on 3D glasses
and press the power button on the glasses.
If you are in bad physical conditions
or feel uncomfortable watching 3D picture
please stop watching TV.
Ending 3D Image Viewing
5 Take off the 3D Glasses and turn off the power.
• If the input signal switches to 2D, 2D images are displayed
automatically.
• 3D mode is canceled automatically when the setting is
changed, input selection is changed, or the power is
turned off.
Receiving a 3D Image Signal That Cannot
Be Detected Automatically
1 Press 3D.
• A screen appears prompting you to select between 3D
and 2D image viewing.
3D
2D
3D
2 Press c/d to select “3D” or “2D”, and then press
When “3D Auto Change” is set to “Off”
• The following message is displayed. Press 3D.
ENTER.
• To view in 3D mode: Select “3D”, and then go to step 3.
• To view in 2D mode: Select “2D”, and then go to step 6.
3 Press c/d to select the 3D signal type ( “2D➝3D”,
3D picture is detected.
Press the power button on the 3D glasses.
(Need to wear the 3D glasses to watch 3D picture)
“Side by Side” or “Top and Bottom”) and then press
ENTER.
• Press c/d to select "Yes", and then press ENTER.
2D -> 3D
Side by Side
Top and Bottom
Select to convert regular 2D picture to 3D.
Yes
No
2 Turn on the 3D Glasses and place them on your
head.
3 You can now view 3D images.
• If you select the same system as that of the input signal,
3D images are displayed.
4 Turn on the 3D Glasses and place them on your
head.
5 You can now view 3D images.
47
LC-90LE745U_E.indb 47
2012/04/06 16:49:59
Enjoying 3D Image Viewing
Switching from 3D to 2D Mode
6 Press c/d to select the 2D signal type ( “Side by
Side” or “Top and Bottom”) and then press ENTER.
Configuring the TV Settings to
Enhance 3D Image Viewing
Example
Side by Side
Top and Bottom
Select when two images are displayed next to each other.
• If you select the same system as that of the input signal,
2D images are displayed.
• Take off the 3D Glasses and turn off the power.
Picture
Settings
Picture Settings
AV MODE (Changing Pic.Quality)
[STANDARD]
OPC
[On:Display]
Backlight
Ending 3D Image Viewing
[ b5] a16
7 Take off the 3D Glasses and turn off the power.
Watching 2D Images in 3D
You can convert normal 2D images into 3D images.
1 Press 3D.
2 Press c/d to select “2D➝3D convert”, and then
press ENTER.
3 Turn on the 3D Glasses and place them on your
head.
• The TV returns to 2D mode after 1 hour has passed.
Switching to the Previous Mode
You can switch back to the previous mode by pressing 3D.
1 Press 3D.
• A confirmation screen is displayed.
Menu
Contrast
[b30]
0
Brightness
[ 0] a30
Color
[ b2] a30
Tint
[ 0] a30
Sharpness
[ b2] a10
b16
b40
b30
b30
b30
b10
Advanced
Reset
1 Press MENU to display the MENU screen, and then
press c/d to select “Picture Settings”.
2 Press a/b to select a specific adjustment item,
and then press ENTER.
3 Press a/b (or c/d) to select the desired item,
and then press ENTER.
4 Press MENU to exit.
Yes
No
• Which items can be selected/adjusted differs depending
on whether the TV is in 2D mode or in 3D mode.
2 Select “Yes” and then press ENTER.
• The TV returns to the previous mode.
3D Menu
AV MODE
The audio and video settings can be changed to suit
the program or input content being watched.
STANDARD(3D): For a highly defined image in a normal
lighting.
MOVIE(3D): For a movie.
GAME(3D): Lowers image brightness for easier viewing.
• You can select AV MODE by pressing AV MODE on the
remote control unit.
Pressing 3D in 3D mode displays the 3D menu. Press
the colored buttons to make the necessary settings.
B: 3D Surround (See page 31.)
The surround mode changes each time you press B.
C: 2D➝3D Convert Effect (See page 49.)
D: 3D Setup (See page 49.)
48
LC-90LE745U_E.indb 48
2012/04/06 16:49:59
Enjoying 3D Image Viewing
3D Setup
You can make various settings to enhance 3D image viewing.
Example
System
Options
Menu
System Options
View Option
3D Setup
AQUOS LINK Setup
Terminal Setting
1 Press MENU to display the MENU screen, and then
press c/d to select “System Options”.
2 Press a/b to select “3D Setup”, and then press
3
4
5
ENTER.
Press a/b to select a specific item, and then press
ENTER.
Press a/b (or c/d) to select the desired setting,
and then press ENTER.
Press MENU to exit.
3D Auto Change
This setting can be used to switch to 3D mode
automatically when a 3D identification signal is
detected.
Set the desired mode according to the type of media
you are viewing, such as video from a connected
device or video from an internet application.
2D➝3D Convert Effect
You can adjust the 3D effect when converting images
from 2D mode to 3D mode.
Select a desired level of convert effect from +1 to +16.
• This function is only available when converting 2D images
to 3D images.
• When you use this function, image conversion on the TV
will result in some differences in the original images and
how they appear.
• 2D images that have been converted to 3D images may be
viewed only for personal use.
Viewing Time Info
This displays the elapsed time of 3D image viewing.
Yes: Displays the elapsed viewing time on the screen
every hour.
No: Does not display the elapsed viewing time.
3D Test
This displays 3D images for testing the 3D operation.
Clicking "Start" on the screen plays back 3D test
images.
• If you press RETURN during playback, the previous
screen will be displayed.
3D Glasses Control
To enable this function, set "TV Location" to "Store".
Selecting "Yes" prevents the 3D Glasses from receiving
3D signals from other TVs.
Mode 1: 3D mode is selected automatically when a 3D
signal is detected while viewing video from a VOD
service or HDMI-connected equipment.
Mode 2: 3D mode is selected automatically when, in
addition to detecting a 3D signal while viewing video
from a VOD service or HDMI-connected equipment, a
video pattern with "Side by Side" or "Top and Bottom"
format is also detected.
Off: Auto change is not performed.
• This function does not work when the input source is
Composite, Component, RGB or Analog/Digital tuner.
3D Depth Control
Select the method for adjusting the 3D depth.
Auto: The depth is adjusted automatically.
Manual: You can manually adjust the depth using the
function "Depth Change".
• This function is only available when the input signal is 3D.
• This function is not displayed depending on the type of 3D
signal.
Depth Change
Adjusts the depth manually. "0" is the level where no
adjustment is made.
• This function is only available when "3D Depth Control" is
"Manual".
49
LC-90LE745U_E.indb 49
2012/04/06 16:49:59
Enjoying 3D Image Viewing
• Appropriate 3D Glasses are required to view 3D images. Purchase 3D Glasses for use with Sharp brand 3D LCD TVs.
■ 3D Glasses lenses
• Do not apply pressure to the lenses of the 3D Glasses. Also, do not drop or bend the 3D Glasses.
• Do not scratch the surface of the lenses of the 3D Glasses with a pointed instrument or other object. Doing so may damage
the 3D Glasses and reduce the quality of the 3D image.
• Use only the cloth provided with the optional 3D Glasses to clean the lenses.
■ 3D Glasses infrared receiver
• Do not allow the infrared receiver to become dirty, and do not attach stickers to or otherwise cover the infrared receiver. Doing
so may prevent the receiver from operating normally.
• If the 3D Glasses are affected by other infrared data communication equipment, the 3D images may not be displayed correctly.
■ Caution during viewing
• Do not use devices that emit strong electromagnetic waves (such as cellular phones or wireless transceivers) near the 3D
Glasses. Doing so may cause the 3D Glasses to malfunction.
• The 3D Glasses cannot operate fully at extreme high or low temperatures. Please use them within the specified usage
temperature range.
• If the 3D Glasses are used in a room with fluorescent lighting (60 Hz), the light within the room may appear to flicker. In this
case, either darken or turn off the fluorescent lights when using the 3D Glasses.
• Wear the 3D Glasses correctly. 3D images will not be correctly visible if the 3D Glasses are worn upside down or back-to-front.
• Other displays (such as computer screens, digital clocks, and calculators) may appear dark and difficult to view while wearing
the 3D Glasses. Do not wear the 3D Glasses when watching anything other than 3D images.
• If you lie on your side while watching the TV with 3D Glasses, the picture may look dark or may not be visible.
• Be sure to stay within the viewing angle and optimum TV viewing distance when watching 3D images. Otherwise, you may not
be able to enjoy the full 3D effect.
• The 3D Glasses may not work properly if there is any other 3D product or electronic devices turned on near the glasses or TV. If
this occurs, turn off the other 3D product or electronic devices or keep the devices as far away as possible from the 3D Glasses.
• Stop using the 3D Glasses in any of the following situations:
– When images consistently appear doubled while you are wearing the 3D Glasses
– When you have difficulty perceiving the 3D effect
• If the 3D Glasses are faulty or damaged, stop using them immediately. Continued use of the 3D Glasses may cause eye
fatigue, headaches and illness.
• If you have any abnormal skin reaction, stop using the 3D Glasses. In very rare instances, such reactions may be due to an
allergic reaction to the coating or materials used.
• If your nose or temples become red or you experience any pain or itchiness, stop using the 3D Glasses. Pressure caused by
long periods of use may lead to such reactions and may result in skin irritation.
50
LC-90LE745U_E.indb 50
2012/04/06 16:50:00
Enjoying 3D Image Viewing
Specifications – 3D Glasses
Product
3D Glasses
Model number
AN-3DG20
Lens type
Liquid crystal shutter
Power supply
DC5V (supplied by a USB terminal of a Sharp LCD TV)
Battery
Lithium ion polymer rechargeable battery (DC3.7V 70mAh)
Battery life*
Approx. 30 hours of continuous use
Charging time
90 minutes
Dimensions (W x H x D)
6 15/16 × 1 23/32 × 6 13/16 inch (175.5 × 43.0 × 173.0 mm)
Weight
Approx. 0.1 lbs./40.0 g (including the lithium ion polymer rechargeable battery)
Operating temperature
50°F to 104°F (10°C to 40°C)
(The 3D Glasses cannot operate fully at extreme high or low temperatures. Please use them
within the specified usage temperature range.)
* Battery life: A rechargeable battery becomes depleted from repetitive usage, and the battery life gradually becomes shorter
(the battery life varies with your usage environment). The above is the value at the factory default state and quality is not
guaranteed by the value.
The product serial number is displayed on the 3D Glasses as indicated in the illustration on
the left. The first four digits represent the product color and the date of manufacture.
Example: Black colored glasses manufactured on April 10, 2011
S/N : B 1 4 A
Bottom
Manufacture number
Color
B: Black
Year of
manufacture
1: 2011
2: 2012
Month of
manufacture
1: 1
2: 2
3: 3
8 :8
9 :9
A : 10
B : 11
C: 12
Day of
manufacture
1: 1 A : 10
2: 2 B : 11
3: 3
H : 17
J : 18
N : 22
P : 23
W: 30
X : 31
* “I”, “O”, “Y” and “Z” are not used.
This symbol attached on the product and its individual pack refers to recycling in the U.S. and Canada.
The RBRC™ Battery Recycling Seal on the Lithium-ion (Li-ion) batteries/battery packs indicates SHARP is
voluntarily participating in an industry program to collect and recycle these batteries/battery packs at the end
of their useful life, when taken out of service in the United States or Canada. The RBRC™ program provides a
convenient alternative to placing Li-ion batteries into the trash or municipal waste stream, which is illegal in some
areas. Please call 1-800-822-8837 for information on Li-ion battery recycling in your area. SHARP’s involvement in
this program is part our commitment to preserving our environment and conserving our natural resources.
(RBRC™ is a trademark of the Rechargeable Battery Recycling Corporation.)
• Please contact your local authority for the correct method of disposal of this product and/or packing.
51
LC-90LE745U_E.indb 51
2012/04/06 16:50:00
Enjoying Photo/Music/Video Playback
You can connect the TV to a USB memory device, USB hard drive or home network (DLNA) server to enjoy
viewing pictures, listening to music, and watching videos.
• Depending on the USB memory device/USB hard drive/home network (DLNA) server, the TV may not be able to recognize the
recorded data.
• It may take time to read the recorded data if the USB memory device/USB hard drive/home network (DLNA) server contains
many files or folders.
• Use only alphanumeric characters for naming files.
• File names over 80 characters (may vary depending on character set) may not be displayed.
Connecting a USB Memory Device/USB Hard Drive
Insert the USB memory device with recorded photos, music or videos into the USB 1 or USB 2 terminal on the TV.
• If USB memory devices are inserted into both terminals, the USB 1 terminal has priority.
or
• When connecting a USB hard drive, be sure to use a hard drive with an AC adapter.
• Do not remove a USB memory device or memory card from the TV while transferring files, using the slide show function, or
switching screens, or before you exit "USB" from the INPUT list.
• Do not insert and remove a USB memory device/USB hard drive to and from the TV repeatedly.
• When using a card reader, be sure to insert a USB memory device first.
• USB input cannot be selected when displaying the browser. Close the browser first.
CAUTION
• Do not use a USB extension cable when connecting a USB memory device to the USB terminal on the TV.
• Using a USB extension cable with the USB memory device may prevent the TV from performing correctly.
Connecting a Home Network (DLNA) Server
Connect the TV to the home network (DLNA) server using an ETHERNET cable.
• You can also connect a Home Network (DLNA) server by using a wireless LAN.
ETHERNET cable
Home network (DLNA) server
Router
• Do not disconnect a home network (DLNA) server from the TV while transferring files, when a screen is switching to another or
before you exit "Home Network (DLNA)" from the INPUT list.
• Do not connect and disconnect a home network (DLNA) server from the TV repeatedly.
52
LC-90LE745U_E.indb 52
2012/04/06 16:50:00
Enjoying Photo/Music/Video Playback
USB Device Compatibility
Selecting the Folders to Play Back
USB device
File system
Photo file
format
Music file
format
• To play back data on a USB memory device, insert the
USB memory device on the TV. USB mode is selected
automatically. (Go to step 2)
• Use the following procedure to switch back to USB mode
after switching from USB mode to another mode.
1 Select "USB" or "Home Network (DLNA)" from
INPUT list screen.
2 Press D.
3 Press a/b (or c/d) to select the drive/server
where you want to find your files, and then press
ENTER.
• For USB mode, select the drive.
• When in DLNA mode, select the server.
4 Press c/d to select "Photo", "Music" or "Video",
and then press ENTER.
Example
Photo
Music
Video
5 Press c/d to select the desired folder, and then
press ENTER.
• The Media screen can be displayed even by using the
application window. To display the application window,
press SmartCentral. (See page 24.)
• You cannot switch the input mode if a USB memory device
is not connected.
• You do not need to select the drive/server in step 2 when
there is only one drive in the connected USB memory
device or there is only one home network (DLNA) server
connected to the TV.
• 16 is the maximum number of USB drives and 10 is the
maximum number of home network (DLNA) servers that
can be displayed.
• If the TV is turned off and then on again, the number
assigned to the USB drive may change.
• "VIEW MODE" is fixed during the Photo or Music mode.
During "Video mode", you can select "Auto" or "Original".
• The key guide display disappears automatically after a
particular time has elapsed. To display the key guide
display again, press DISPLAY.
USB Memory, USB card reader (Mass
Storage class), USB hard drive
FAT/FAT32/NTFS (USB hard drive only)
JPEG (.jpg) (DCF2.0 compliant)
Multi-Picture Format (.mpo) (CIPA DC007 Compliant)
MP Type : Multi view individually image
(stereoscopic view)
MP3 (.mp3)
Bitrate: 32k, 40k, 48k, 56k, 64k, 80k,
96k, 112k, 128k, 160k, 192k, 224k,
256k, 320kbps
Sampling frequency: 32k, 44.1k, 48kHz
Video file format
File
Container
Video
extension
DivX 3.11/4.x/5.1/6.0
XviD
.avi
AVI
H.264
MPEG4
Motion Jpeg
DivX 3.11/4.x/5.1/6.0
XviD
.mkv
MKV
H.264
MPEG4
DivX 3.11/4.x/5.1/6.0
XviD
.asf
MPEG4
ASF
.wmv
VC-1
Windows Media Video v9
.mp4
H.264
MP4
.mov
MPEG4
(SMP4)
.3gp
Motion Jpeg
.vro
MPEG2
.mpg
PS
MPEG1
.mpeg
Audio
MP3
Dolby Digital
LPCM
ADPCM
MP3
Dolby Digital
LPCM
ADPCM
MP3
Dolby Digital
LPCM
WMA
MP3
AAC
Dolby Digital
MPEG
LPCM
•
•
•
•
Progressive format jpeg files are not supported.
USB 1.1 devices may not be played properly.
Operation using USB hubs is not guaranteed.
Some video file formats may not be played depending on
the file.
• Some images may not be displayed in the appropriate
aspect ratio depending on the file format.
Home Network (DLNA) Server Compatibility
Photo file format
Music file format
Video file format
JPEG
LPCM, MP3
MPEG2-PS, MPEG2-TS,
WMV, ASF, MP4, MOV, AVI
• Progressive format jpeg files are not supported.
• Some video file formats may not be played depending on
the file or the server.
• WMV, ASF, MP4, MOV and AVI are non-DLNA contents.
53
LC-90LE745U_E.indb 53
2012/04/06 16:50:00
Enjoying Photo/Music/Video Playback
Playing Back Files on a USB Memory
Device/Home Network (DLNA) Server
Photo Mode
Viewing Thumbnails
Example
...
picture 1
picture 2
picture 3
picture 4
picture 5
...
• When there are invalid photo files, the X mark will be
displayed for the file. (USB mode only.)
• The icon
appears on the thumbnails of 3D images. If
you do not switch to 3D mode for the 3D images, they will
be displayed in 2D. (USB mode only.)
• You can see the file name, shooting date, file size and pixel
size of the selected photo in the lower-left corner of the
screen (shooting date is only available in the EXIF file format).
Viewing Individual Photos
The photo selected on the thumbnail selection screen
is displayed.
Buttons for individual display operation
Buttons
c/d
This screen image is for the USB mode. It may be slightly
different in the Home network (DLNA) mode.
RETURN
3D
A (red)
B (green)
Description
Go to the previous/next photo in the same
directory.
Return to the thumbnail selection screen.
Switches between 2D and 3D modes.
Rotate the photo by 90 degrees to the left.
Rotate the photo by 90 degrees to the right.
• Rotating photos only applies to the temporarily selected
item and this setting is not saved.
• In 3D mode, you cannot rotate the photos.
• The key guide display disappears automatically after a
particular time has elapsed. To display the key guide
display again, press DISPLAY.
Slide Show
The photos displayed on the thumbnail selection
screen are displayed as a slide show.
Buttons for slide show operation
Buttons for thumbnail operations
Buttons
a/b/c/d
ENTER
RETURN
A (red)
B (green)
C (blue)*
D (yellow)
Description
Select a desired item.
When selecting a folder icon:
Enter this directory.
When selecting a photo thumbnail:
Enlarge the photo.
Return to the previous process.
USB mode:
Select the images to be displayed. Press
this button to add or remove a checkmark.
Home Network (DLNA) mode:
Display the Media screen.
Display the music list screen. You can select
the background music to be played for the
slide show.
Start the slide show.
Display the USB MENU/Home Network
(DLNA) Menu screen.
Buttons
RETURN
3D
D (yellow)
Description
Return to the thumbnail selection screen.
Switches between 2D and 3D modes.
Display the USB MENU/Home Network
(DLNA) Menu screen.
• The selected BGM is played repeatedly.
• The slide show continues until you press RETURN.
• For setting the slide show speed, select "Select Slide Show
Interval" on the USB MENU/Home Network (DLNA) Menu screen.
• The key guide display disappears automatically after a
particular time has elapsed. To display the key guide
display again, press DISPLAY.
* This function is available only for the USB mode.
54
LC-90LE745U_E.indb 54
2012/04/06 16:50:00
Enjoying Photo/Music/Video Playback
USB Menu
On the menu to be displayed in USB mode, use a/b to
select an item and make settings to your preferences.
Example
Music Mode
Example
...
USB MENU
3D Display
[On]
Select Slide Show Interval
[10sec]
SONG_03.MP3
music 1
music 2
music 3
SONG_01.MP3
SONG_02.MP3
SONG_03.MP3
SONG_04.MP3
SONG_05.MP3
SONG_06.MP3
SONG_07.MP3
music 4
music 5
I
I
I
I
I
I
I
...
3:42
4:55
4:35
4:08
4:20
3:55
4:26
0:14 / 4:35
Select Slide Show BGM
Set All Slide Show Image
Reset All Slide Show Image
This screen image is for the USB mode. It may be slightly
different in the Home network (DLNA) mode.
Remove USB Device
■ 3D Display
You can view photos in 3D.
On: Displays the photos in 3D.
Off: Normal viewing mode.
• You can select "3D display" from "USB MENU" only when
the thumbnails screen for the photo mode in USB mode is
displayed on the screen.
• Depending on the file, the photos may not be displayed in
3D.
■ Select Slide Show Interval
Specify the length of time before the next image
appears.
Press a/b to select the desired length of the time, and
then press ENTER.
5sec/10sec/30sec/60sec
• For DLNA mode, follow the same procedure.
• Depending on the photo files, the length of the slide show
interval may differ from the selected interval time.
■ Select Slide Show BGM
The music list screen appears when you select "Select
Slide Show BGM".
You can select the music to be played in the
background while the slide show is being displayed.
1 Select the music you want to play from the music
list.
• For operations on the music list screen, see "Music
Mode".
Buttons for music mode
Buttons
a/b/c/d
ENTER
RETURN
A (red)
B (green)
C (blue)
D (yellow)*
Description
Select a desired item.
When selecting a folder icon:
Enter this directory.
When selecting a music file:
Play music.
Return to the previous process.
USB mode:
Select the music to be played back. Press
this button to add or remove a checkmark.
Home Network (DLNA) mode:
Display the Media screen.
Stop music.
Play/Pause music.
Display the USB MENU screen.
* This function is available only for the USB mode.
• When there are invalid music files, the X mark will be
displayed for the file. (USB mode only.)
• The displayed play time may differ slightly from the actual
play time depending on the files.
2 Press RETURN to display the thumbnail selection
screen, and then press C to start the slide show
and the background music.
• All of the music files are selected by default.
■ Set/Reset All Slide Show Image
Selecting "Set All Slide Show Image" or "Reset All
Slide Show Image" will display the thumbnail selection
screen. On the screen, set or reset the images to be
displayed in the slide show.
Set All Slide Show Image: Checkmarks are added to all
the images.
Reset All Slide Show Image: Removes all the
checkmarks from all the images.
■ Remove USB Device
To remove the USB device properly, use c/d to
select "Yes" and then press ENTER.
LC-90LE745U_E.indb 55
55
2012/04/06 16:50:01
Enjoying Photo/Music/Video Playback
USB Menu
On the menu to be displayed in USB mode, use
a/b to select an item and make settings to your
preferences.
Buttons for playing mode
Buttons
a
Example
USB MENU
Set All Auto Play
Reset All Auto Play
*
Remove USB Device
* See page 55 for details on the Remove USB Device
function.
■ Set/Reset All Auto Play
Selecting "Set All Auto Play" or "Reset All Auto Play"
will display the music list screen. On the screen, set or
reset the music to be played back in the slide show.
Set All Auto Play: Checkmarks are added to all the
music files.
Reset All Auto Play: Removes all the checkmarks from
all the music files.
Video Mode
Example
...
video 1
video 2
VIDEO_01.avi
VIDEO_02.divx
VIDEO_03.divx
VIDEO_04.avi
VIDEO_05.divx
VIDEO_06.divx
VIDEO_07.avi
video 3
video 4
video 5
I
I
I
I
I
I
I
...
3:42
4:55
4:35
4:08
4:20
3:55
4:26
This screen image is for the USB mode. It may be slightly
different in the Home network (DLNA) mode.
Description
Go to the beginning of a file by pressing once
or to the previous file by pressing twice.
Go to the next file.
b
d
USB mode:
The fast forward speed changes every time you
press d. After playing to the end, the TV goes
to the next file and starts to play.
Home Network (DLNA) mode:
Jump forward in a video. *2
c
USB mode:
The reverse speed changes every time you
press c. After going back to the beginning, the
TV starts to play the same file.
Home Network (DLNA) mode:
Jump back in a video. *2
ENTER
USB mode:
Pause the video.
Home Network (DLNA) mode:
Play/Pause the video. *2
RETURN Go back to the file selection screen.
3D
Switches between 2D and 3D modes.
A (red)*1 Jump to the scene where playback was last
stopped.
B (green) Stop a video.
C (blue) Display the USB/home network (DLNA)
operation panel.
D (yellow)*1 Display the USB MENU screen.
0-9*1
Jump to a point in the video during playback of
a file without chapters.
You can jump to a later point by pressing a
higher number.*3
*1 These functions are available only for the USB mode.
*2 Jump forward/back and play/pause may not be available
depending on the files.
*3 During playback of a file without chapters, playback points
are set automatically. Playback points are set at intervals of
a one-tenth of playback time.
Example for a file with a playback time of 100 minutes:
Pressing 1 jumps 10 minutes forward, and pressing 2 jumps
20 minutes forward. Pressing 0 returns to the start of the file
being played back.
Buttons for file selecting operations
Buttons
Description
a/b/c/d Select a desired item.
ENTER
When selecting a folder icon:
Enter this directory.
When selecting a music file: Play the video.
RETURN Return to the previous process.
A (red)
USB mode:
Select/deselect items (checkmarks are added
to the selected items).
Home Network (DLNA) mode:
Display the Media screen.
D (yellow)* Display the USB MENU screen.
* This function is available only for the USB mode.
56
LC-90LE745U_E.indb 56
2012/04/06 16:50:01
Enjoying Photo/Music/Video Playback
■ Using the operation panel
You can use the operation panel for video playback
operations.
You can call up this operation panel by pressing
MENU after you press a/b to select "USB Operation
Panel"/"Home Network (DLNA) Operation Panel" from
"System Options" > "View Option".
Example
Buttons for using the Home Network (DLNA)
operation panel
d

)
/
+
Audio
Title
Starts playback.
Go to the beginning of a file by pressing once
or to the previous file by pressing twice.
Sets pauses and still pictures.
Go to the next file.
Playback stops.
Jump back in a video.
Jump forward in a video.
CC
Resume
jump
Buttons for using the USB operation panel
•
Hold down to go in reverse.
Starts playback.
Œ
Hold down to fast forward.

Video without chapters: Press once to return
to the previous playback point.* Press twice to
return to the previous file.
Video with chapters: Press once to return to
the previous chapter. Press twice to return to
the previous file.
)
Sets pauses and still pictures.
/
Video without chapters: Press once to advance
to the next playback point.* Press twice to
display the next file.
Video with chapters: Press once to advance
to the next chapter. Press twice to display the
next file.
Audio
Change the audio when multiple audio is
available for the video you are watching.
+
Playback stops.
CC
Change the Closed Caption display.
Title
Displays the title (edition).
Resume
Jump to the scene where playback was last
jump
stopped.
* During playback of a file without chapters, playback points
are set automatically. Playback points are set at intervals of a
one-tenth of playback time.
Example for a file with a playback time of 100 minutes:
Playback points are set every 10 minutes. Pressing /
one time after viewing the file for 15 minutes jumps to the
20-minute playback point.
d
• Reverse/fast forward continues from one file to another
during continuous playback.
• Use "CC" on the operation panel to change the Closed
Caption display. You can also switch the Closed Caption
display by using "System Options" > "View Option" >
"Change CC" or by pressing CC on the remote control unit.
• Use "Audio" on the operation panel to change the audio.
You can also switch the audio by using "System Options" >
"View Option" > "Change Audio".
USB Menu
On the menu to be displayed in USB mode, use
a/b to select an item and make settings to your
preferences.
Menu for file selecting operations
Example
USB MENU
Set All Auto Play
Reset All Auto Play
*
Remove USB Device
* See page 55 for details on the Remove USB Device
function.
■ Set/Reset All Auto Play
Selecting "Set All Auto Play" or "Reset All Auto Play"
will display the video list screen. On the screen, set or
reset the video to be played back in the slide show.
Set All Auto Play: Checkmarks are added to all the
video files.
Reset All Auto Play: Removes all the checkmarks from
all the video files.
Menu for playing mode
Example
USB MENU
Title (Edition)
Chapter
Show Video Information
*
Remove USB Device
* See page 55 for details on the Remove USB Device
function.
■ Title (Edition)/Chapter
Selecting "Title (Edition)" or "Chapter" will display a list
of titles/chapters contained in the video file. Select the
title or chapter you want to play back.
• The selected title or chapter is played back.
• "0-9" is displayed for files without chapters. Playback
jumps to the playback point of the selected number.
• If there is Edition information, this screen is displayed when
the title is selected.
• If there is no title or edition, you cannot select "Title
(Edition)".
• "Chapter" cannot be selected when there is no chapter.
■ Show Video Information
The information of the current file is displayed.
57
LC-90LE745U_E.indb 57
2012/04/06 16:50:01
Enjoying Photo/Music/Video Playback
Example
Initial
Setup
Menu
Playing Back Files from a Portable
Device or PC
With the remote playback function, you can use your
portable device to play back pictures, video, and music
on the home network server.
Initial Setup
EZ Setup
Broadcasting Setup
Internet Setup
Language
[English]
DivX® Setup
Individual Setup
DivX® Setup
This is the function to confirm your registration code.
You need to register the code at http://www.divx.com.
1 Press MENU to display the MENU screen.
2 Press c/d to select "Initial Setup", and then press
ENTER.
3 Press a/b to select "DivX® Setup", and then
press ENTER.
®
■ DivX VOD Registration
You can find your registration code on this menu. You
need to register the TV at http://www.divx.com before
playing the DivX content.
®
■ DivX VOD Deregistration
You can find your deregistration code on this menu.
You need to deregister the TV at http://www.divx.com
to release the registration.
• This function is available only for the USB mode.
• This function may not work while an Internet application is
being used.
• This TV is a DLNA certified Digital Media Renderer. (DMR)
• To use the remote playback function, your portable device
must be a DLNA Certified Digital Media Controller.
• A wireless access point is required to use a portable
device.
Set Up Home Network
Make the settings for remote playback.
1 Press c/d to select "Initial Setup", and then press
ENTER.
2 Press a/b to select "Internet Setup", and then
press ENTER.
3 Press a/b to select "Set Up Home Network", and
then press ENTER.
4 Press a/b to select the specific adjustment item,
and then press ENTER to set each item.
■ Remote Control Play Settings
This setting allows the TV to perform remote playback.
Permitted: Allows remote playback.
Not allowed: Does not allow remote playback.
■ Timeout Setup
This sets the time until the TV returns automatically to
TV mode after remote playback ends.
10 sec./60 sec.: When the set time has elapsed after
remote playback ends, the TV returns automatically to
TV mode.
No: Select this to manually switch the TV after remote
playback ends.
• This function may not work while an Internet application is
being used.
• For information on the compatible formats, see "Home
Network (DLNA) Server Compatibility" on page 53.
•
58
LC-90LE745U_E_05.indd 58
2012/04/23 13:29:54
Other Viewing Options
Presetting Remote Control Function
Operating the Connected Equipment
You can operate the connected AV products (AV
receiver, cable box, SAT tuner, DTV, VCR, BD, DVD,
LD) using the presetting manufacturer function of your
remote control unit.
To operate the connected equipment, press STB,
DVD•VCR or AUDIO to select your device. (STB
(cable/satellite set-top box), BD, DVD, VCR or AUDIO.)
The remote control unit button will function as follows.
• When you operate VCR, DVD or BD, press INPUT to select
the terminal connected to your device.
• CABLE and SAT cannot be selected at the same time.
1
1 POWER (SOURCE)
2
3
4
5
7
8
9
10
• Turns the connected equipment power on and off.
2,
• Starts playback. (VCR, BD, DVD)
3 *
• Rewinds the tape and allows picture search. (VCR)
• Hold down to go in reverse. (BD, DVD)
4+
• Stops the tape transport. (VCR)
• Playback stops when pressed. With some Blu-ray disc/
DVD players, pressing the button twice may open the
disc tray. (BD, DVD)
6
5.
• Pressing quickly once takes you to the start of the chapter
currently playing. Each time you press it, you move back
to the start of the previous chapter. (BD, DVD)
11
12
13
6 0–9, • (DOT) (STB)
• Press a button (or buttons) that corresponds to the
channel that you wish to watch.
7• Rapidly advances the tape and allows picture search.
(VCR)
• Hold down to fast forward. (BD, DVD)
8)
• Sets pauses and still pictures. (VCR, BD, DVD)
14
9/
• Pressing quickly once takes you to the start of the next
chapter. Each time you press it, you move ahead to the
start of the next chapter. (BD, DVD)
10
Presetting manufacturer codes
1 Press an appropriate button (STB, DVD•VCR or
AUDIO) to operate the connected equipment.
2 Press an appropriate button (STB, DVD•VCR or
AUDIO) and DISPLAY at the same time to enter
the code registration mode.
3 Press 0–9 to enter the manufacturer code. (See
page 60.)
• Preset mode is finished once the LED no longer lights
up.
4 After registering the code, the LED will stop blinking
then turn off after one second. (If you perform an
incorrect operation, the LED will blink quickly then
turn off.)
(REC
• Starts recording. (VCR)
11 FLASHBACK
• Press to switch between the current channel and the
channel you were watching immediately before. Some
manufacturers do not preset FLASHBACK. (STB)
12 CHU/V
• Press CHU or CHV to tune in to a higher or lower
channel. (STB)
• Press to select the channel of the TV tuner on the VCR.
(VCR)
13 MENU
• When this button is pressed, the BD/DVD menu will
display. (BD, DVD)
14 a/b/c/d, ENTER
• a/b/c/d: Press the button to select items on the STB
GUIDE screen or STB MENU screen. (STB)
Press the button to select items on the BD/DVD menu
screen. (BD, DVD)
• ENTER: Press to activate the selected function. (STB,
BD, DVD)
59
LC-90LE745U_E.indb 59
2012/04/06 16:50:01
Other Viewing Options
Manufacturer codes
VCR BRAND
AUDIO DYNAMICS
BROCKSONIC
CANON
CRAIG
CURTIS MATHIS
DBX
EMERSON
GE
INSTANT REOLYA
JC PENNEY
JVC
KENWOOD
MAGNAVOX
MAGNIN
MEMOREX
MONTGOMERY WARD
NEC
PANASONIC
PENTAX
PHILCO
PHILIPS
QUASAR
REALISTIC
SAMSUNG
SHARP
SONY
SYLVANIA
TATUNG
TEAC
TMK
YAMAHA
BD/DVD/LD BRAND
DENON
JVC
KENWOOD
MAGNAVOX
MARANTZ
MITSUBISHI
PANASONIC
PHILIPS
PIONEER
PROSCAN
RCA
SAMSUNG
SHARP
SONY
TOSHIBA
YAMAHA
ZENITH
REMOTE CONTROL CODE
NUMBER
09
13
04
12
04
09
10, 13, 14
04
04
04
09, 16, 17, 22
09
04, 05, 06
12
04
02
09
04, 18, 19, 20, 21
05
04, 05
04, 05, 06
04
01, 02
11, 12
01, 02, 03
07, 08, 15
04, 05, 06
09
09
10
09
REMOTE CONTROL CODE
NUMBER
STB BRAND
ANVISION
CABLE STAR
DISH NETWORK
DIRECTV
EAGLE
G.INSTRUMENT
GERROLD
JERROLD
MAGNAVOX
MOTOROLA
OKA SIGMA
PANASONIC
PHILIPS
PIONEER
RANDTEK
RCA
S.ATLANTA
VIEWSTAR
ZENITH
REMOTE CONTROL CODE
NUMBER
04, 05
04, 05
39, 40
41
05
02, 03, 10, 11, 17, 20
17
02, 03, 10, 11, 12, 20,
25-34
04, 05, 08, 12, 15, 16,
18, 19, 22, 23
38
07
14, 21
04, 05, 08, 13, 15, 16,
18, 19, 22, 23
07
04, 05
14, 36*, 37*
01, 09, 24
04, 05, 08, 13, 15, 16,
18, 19, 22, 23
06, 35
• Numbers marked with * are SAT codes, all others are STB
codes.
AUDIO BRAND
SHARP
SHARP (SOUND BAR)
REMOTE CONTROL CODE
NUMBER
01
02
24
31
36
26
26
28
24, 37
26, 38
30, 33, 35
25
25, 39
29, 34
23, 32, 41, 42
27, 40
26
24
26
• Depending on the brand, the codes of some BD players
may not be supported.
60
LC-90LE745U_E.indb 60
2012/04/06 16:50:01
Using AQUOS LINK
Controlling HDMI Equipment Using AQUOS LINK
What’s AQUOS LINK?
• Using the HDMI CEC (Consumer Electronics Control) protocol, with AQUOS LINK you can interactively operate
compatible system equipment (Blu-ray disc equipment, AV amplifier, DVD).
• By connecting AQUOS LINK-compatible devices with HDMI-certified cables to the TV, you can control a
recorder or AV amplifier using the remote control of the TV.
• AQUOS LINK allows you to operate the HDMI-connected equipment with one remote control.
Example
Connecting AQUOS
BD player via AQUOS
LINK-compatible
audio system
HDMI-certified cable *
* Use HDMI 1 to connect
ARC-compatible equipment.
HDMI-certified cable
AQUOS BD player
Optical fiber cable
AQUOS LINK-compatible
audio system
Back panel
horizontal inputs
Back panel
vertical inputs
•
•
•
•
•
For connecting the TV to AQUOS LINK-compatible equipment, use commercially available cables.
Point the remote control toward the TV, not to connected HDMI equipment.
Video noise may occur depending on the type of HDMI cable used. Make sure to use an HDMI-certified cable.
Up to 3 pieces of HDMI recording equipment and one AV amplifier can be connected using this system.
These operations affect the HDMI equipment selected as the current input source. If the equipment does not operate, turn on
the equipment and select the appropriate input source using INPUT.
• The AQUOS LINK feature may not operate properly when an HDMI splitter or AV selector unit is used. These devices may
cause interruptions to the image and/or sound.
Connected AQUOS LINK-compatible devices can be operated without
changing the settings of the remote control unit.
The OPTION button will function only when AQUOS LINK is used.
■ One Touch Play
While the TV is in standby mode, it automatically turns on and plays back the
image from the HDMI source.
■ One Touch Recording
Press (REC while you are viewing a broadcast received with the AQUOS
LINK-compatible recorder. The AQUOS LINK automatically recognizes the
connected HDMI device and starts recording.
■ Single remote control
The AQUOS LINK automatically recognizes the connected HDMI device and
you can control the TV and the devices as if using a universal remote control.
■ Control the AQUOS LINK-compatible audio system
Set the volume of AQUOS LINK-compatible audio system.
• The above description is an example of the AQUOS LINK function.
• The steps in “AQUOS LINK Setup” on page 62 need to be completed beforehand.
• Refer to this operation manual and the operation manual of the AQUOS LINK device
to be used with this TV.
61
LC-90LE745U_E.indb 61
2012/04/06 16:50:01
Using AQUOS LINK
AQUOS LINK Setup
Example
System
Options
Menu
System Options
AQUOS LINK Setup
AQUOS LINK Control
[On]
Auto Power On
[Yes]
Selecting Recorder
Channel Select Key
Audio Return Channel
[Auto]
1 Press MENU to display the MENU screen, and then
press c/d to select "System Options".
2 Press a/b to select “AQUOS LINK Setup”, and
then press ENTER.
3 Press a/b to select a specific item, and then press
Channel Select Key
This function can be set for each input terminal.
On: The remote control unit of the TV can be used to
select the channel, display program information, and
perform other operations of the connected AQUOS
LINK-compatible equipment.
Off: This function does not work.
Audio Return Channel
This function allows you to listen to the TV audio via
audio equipment without using an optical fiber cable,
which conventionally is required.
Requirements for using an ARC-compatible AV
amplifier:
• ARC-compatible AV amplifier connected to the ARCcompatible HDMI terminal (HDMI 1).
(Refer to the operation manual of the ARC-compatible
equipment for details.)
• Use of an ARC-compatible cable.
Auto: You can listen to the TV audio with ARCcompatible audio equipment.
Off: This function does not work.
ENTER.
4 Press a/b (or c/d ) to select the desired setting,
and then press ENTER.
5 Press MENU to exit.
• If the TV audio cannot be output from the AV amplifier even
after making the necessary settings, connect the TV to the
AV amplifier with an optical fiber cable and select “Off”.
One Touch Playback
AQUOS LINK Control
Select AQUOS LINK Control to disable the AQUOS
LINK function even when an AQUOS LINKcompatible HDMI device is connected to the TV. This
function prevents the device from starting to operate
unexpectedly.
On: You can operate AQUOS LINK-compatible
equipment.
Off: The AQUOS LINK function does not work.
Auto Power On
If this is activated, the One Touch Play function is
enabled.
Yes: While the TV is in standby mode, it automatically
turns on and plays back the image from the HDMI
source.
No: This function does not work.
Selecting Recorder
When multiple AQUOS LINK-compatible devices are
connected, this function allows you to set the recorder
for recording when you press (REC on the TV’s
remote control unit.
Press a/b to select the recorder for recording.
AQUOS LINK allows you to operate the HDMIconnected equipment with one remote control.
Press d to start playing back a title.
• The last played program is played back. You can use the
following buttons during broadcast viewing.
Buttons
POWER
(SOURCE)
*
,
-
Description
Turns the power of the HDMI connected devices
on and off.
Hold down this button to go in reverse.
Starts playback.
Hold down this button to fast forward.
+
Stops playback.
)
Sets pauses and still pictures.
7
Pressing quickly once takes you to the start of the
chapter currently playing. Each time you press it,
you move back to the start of the previous chapter.
8
Pressing quickly once takes you to the start of the
next chapter. Each time you press it, you move
ahead to the start of the next chapter.
• The buttons 7/8 do not function with the following
Blu-ray disc players currently available.
- BD-HP20U, BD-HP50U
62
LC-90LE745U_E.indb 62
2012/04/06 16:50:02
Using AQUOS LINK
Link Operation Menu
Menu
Link
Operation
Link Operation
One Touch Recording
This function allows easy one-touch recording of the
program being viewed on the TV to AQUOS LINKcompatible equipment with a recording function by
simply pressing (REC on the remote control.
Prepare the connected AQUOS LINK-compatible
recorder for recording. Check the following items.
• Make sure that the antenna cable is connected.
• Check that there is sufficient available space on the
recording media (HDD, DVD, etc.).
• On the TV, use “AQUOS LINK Setup” and “Selecting
Recorder” to select the equipment for recording.
• By default, the recorder connected to HDMI 1 is selected
for recording.
Link
Operation
Menu
Link Operation
Recorder Power On/Off
Start Recording
Device Operation panel
Stop Recording
Play from Rec. List
Show Start Menu
Change Media of Device
Link Booking (Rec. Book)
Change Audio Output Device
[By AQUOS SP]
Change Surround Mode
HDMI Device Selection
AQUOS LINK Setup
1 Press (REC to start recording.
• When you are viewing a broadcast received with the
AQUOS LINK-compatible recorder selected in "Selecting
Recorder", recording to the AQUOS recorder of the
broadcast being viewed starts.
• When you are viewing a broadcast received with
equipment other than the AQUOS LINK-compatible
recorder selected in "Selecting Recorder" or other
external input equipment, pressing (REC on the remote
control does not start recording.
2 Use the Link Operation Menu to stop recording.
1 Press OPTION to display the Link Operation
Menu screen.
2 Press a/b to select “Stop Recording”, and
then press ENTER.
Start/Stop Recording
You can also use the Link Operation Menu for
recording on the connected AQUOS LINK-compatible
equipment.
1 Press OPTION to display the Link Operation Menu
screen.
2 Select “Start Recording”, and then press ENTER to
start recording.
• You can also start recording by pressing (REC on the
remote control unit.
3 Select “Stop Recording”, and then press ENTER to
stop recording.
The Link Operation Menu allows you to make
adjustments during operation of AQUOS LINKcompatible equipment.
1 Press OPTION to display the Link Operation Menu.
2 Press a/b to select the desired item, and then
press ENTER.
• Specific operations differ depending on the item you
select. Following (on the next page) are the basic
operations for each item.
63
LC-90LE745U_E.indb 63
2012/04/06 16:50:02
Using AQUOS LINK
Recorder Power On/Off
You can manually turn on/off the power of the
connected AQUOS LINK-compatible equipment.
Each time you press ENTER, the connected
equipment switches on or off.
Device Operation Panel
You can use the device operation panel to control
playback operations.
Press a/b/c/d to select the desired operation.
• This function works only when AQUOS LINK-compatible
equipment with the Device Operation Panel function is
connected.
Play from Rec. List
This function allows you to display the title list for the
connected equipment and to play back the title you
want to enjoy.
Before using this function.
Power on the AQUOS LINK-compatible equipment,
and select the appropriate external input.
Link Booking (Rec. Book)
You can call up the AQUOS LINK-compatible
recorder's EPG and preset timer recordings using the
TV's remote control.
Select the program on the recorder's EPG.
• You can use a/b/c/d, ENTER, RETURN, EXIT and the
colored buttons.
• This function works only when an AQUOS LINK-compatible
recorder is connected.
• Refer to the operation manual of the recorder for details.
Change Audio Output Device
You can select to listen to the TV sound only from the
AQUOS LINK-compatible audio system.
By AQUOS audio SP: The sound from the TV speaker is
muted and only the sound from the AQUOS LINKcompatible audio system is audible.
• You can use VOL+/- and MUTE.
By AQUOS SP: The sound is output from the TV
speaker.
Change Surround Mode
Select the title with a/b/c/d, and then press d to
start playback.
You can manually change the AQUOS AUDIO speaker
system's sound mode.
The sound mode changes each time you press
ENTER.
• This function works only when AQUOS LINK-compatible
equipment is connected.
• Refer to the operation manual of the AQUOS LINKcompatible audio system for details.
Show Start Menu
You can call up a setup menu from the connected
AQUOS LINK-compatible equipment.
• Depending on the status of the equipment (recording or in
standby mode, etc), the setup menu will not be displayed.
• The setup menu will not be displayed with the player BDHP20U currently available.
Change Media of Device
HDMI Device Selection
If multiple HDMI devices are connected in a daisy
chain, you can specify which device to control here.
Press a/b to select the desired device from a list of
connected HDMI devices, and then press ENTER.
AQUOS Link Setup
You can also display the AQUOS LINK Setup screen
from the Link Operation Menu.
You can switch the media (HDD or DVD) for playback
or recording on the AQUOS LINK-compatible recorder.
• The Media type toggles each time you press ENTER in
"Change Media of Device".
64
LC-90LE745U_E.indb 64
2012/04/06 16:50:02
Using AQUOS LINK
Using a Smartphone with the TV
This function enables you to connect the TV to a smartphone that supports Mobile High-Definition Link (MHL)
using an MHL-compatible cable.
To connect the TV to your MHL-compatible smartphone, be sure to use an MHL-compatible cable (commercially
available).
• You can view pictures and video on a large screen.
• You can play back music files.
MHL-compatible cable
Back panel vertical inputs
• An MHL-compatible portable device is required to use this function. Connect the device to the HDMI 4 terminal.
■ Auto Power On
When an MHL-compatible device is connected to the TV, the TV turns on
automatically.
• This function operates when "AQUOS LINK Control" is set to "On". (See page 62.)
■ Auto Input Selection
When an MHL-compatible device is connected while the TV is on, the input
mode is selected automatically.
• This function operates when "AQUOS LINK Control" is set to "On". (See page 62.)
■ Operation Using the Remote Control
The remote control of the TV can be used to operate a portable device.
• a/b/c/d, ENTER, EXIT, 0-9, • (DOT), ENT, etc.
• The operations vary depending on the connected equipment and content being
viewed.
65
LC-90LE745U_E_06.indd 65
2012/04/23 17:57:36
Using a PC
Displaying a PC Image on the Screen
VIEW MODE
You can select the screen size.
1 Press VIEW MODE.
• The View Mode menu displays.
• The menu lists the View Mode options selectable for the type of video signal currently
being received.
2 Press VIEW MODE or a/b while the View Mode menu is displayed to select a
desired item on the menu.
• You can sequentially select a View Mode that has its own aspect ratio.
•
•
•
•
Connect the PC before making adjustments. (See page 18.)
Selectable screen size may vary with input signal type.
You can have the same settings by choosing "View Mode" on the menu items. (See page 33.)
You may not be able to change the View Mode while in 3D mode.
Example: Screen size images
Input signal
4:3
Normal
Keeps the original
aspect ratio in a full
screen display.
Zoom
For viewing
widescreen
programs. The top
and bottom of the
image is cropped.
Input signal
Stretch
Dot by Dot
16:9
An image fully fills the
screen.
Detects the resolution
of the signal and
displays an image with
the same number of
pixels on the screen.
Stretch
Dot by Dot
An image fully fills the
screen.
Detects the resolution
of the signal and
displays an image with
the same number of
pixels on the screen.
66
LC-90LE745U_E.indb 66
2012/04/06 16:50:02
Using a PC
Example
Menu
System
Options
Audio Select
System Options
View Option
3D Setup
AQUOS LINK Setup
Terminal Setting
Menu Design
O
ti
L
kO t
1 Press MENU to display the MENU screen, and then
press c/d to select "System Options".
2 Press a/b to select "Terminal Setting", and then
3
4
5
press ENTER.
Press a/b to select "PC input" or "Audio Select",
and then press ENTER.
Press a/b to select a specific adjustment item,
and then press ENTER to set each item.
Press a/b (or c/d) to select or adjust the desired
setting, and then press ENTER.
Adjusting the PC Image
Auto Sync. (for Analog PC Input Mode Only)
For automatically adjusting the PC image.
Yes: Auto Sync. starts and "Now adjusting the image."
displays.
No: This function does not work.
• When "Auto Sync." is successful, "Completed" displays. If
not, "Auto Sync." failed.
• "Auto Sync." may fail even if "Completed" displays.
• "Auto Sync." may fail if the computer image has low
resolution, has unclear (black) edges, or is moved while
executing "Auto Sync.".
• Be sure to connect the PC to the TV and switch it on before
starting "Auto Sync.".
Fine Sync.
Ordinarily you can easily adjust the picture as necessary
to change image position using "Auto Sync.". In some
cases, however, manual adjustment is needed to
optimize the image.
H-Pos.: Centers the image by moving it to the left or right.
V-Pos.: Centers the image by moving it up or down.
Clock: Adjust when the image flickers with vertical
stripes.
Phase: Adjust when characters have low contrast or
when the image flickers.
• For resetting all "Fine Sync." adjustment items to the factory
preset values, press a/b to select "Reset", and then press
ENTER.
• It is not necessary to adjust the "Clock" or "Phase" when a
digital signal is being input, so it cannot be selected.
• The default cursor position may not be in the center,
because the screen position variable ranges may be
asymmetrical.
• The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
position-setting screen.
LC-90LE745U_E.indb 67
Setting Audio Input
This function sets the terminal to output the computer
audio.
The adjustment items vary depending on the input
source. Select the input source corresponding to the
terminal connected to the PC and then adjust the
desired item.
■ PC IN
Video: Select this when the TV and PC are connected
using an analog RGB cable and the audio is not input.
Video+Audio: Select this when the TV and PC are
connected using an analog RGB cable and the audio is
input via a Ø 3.5 mm stereo minijack.
■ HDMI 2
HDMI(Digital): Select this when the TV and PC are
connected using an HDMI-certified cable and audio is
input via the same cable.
HDMI+Analog: Select this when the TV and PC are
connected using a DVI-HDMI conversion cable and the
audio is input via a Ø 3.5 mm stereo minijack.
• When "Audio Select" is set to "HDMI(Digital)", sound will
not be produced if you use only an HDMI-certified cable to
connect HDMI-compatible equipment. To produce sound,
you should make an analog audio connection.
• If you want to connect HDMI-compatible equipment
using only an HDMI-certified cable, set "Audio Select" to
"HDMI(Digital)".
PC Compatibility Chart
It is necessary to set the PC correctly to display XGA
and WXGA signal.
Resolution
720 x 400
VGA
640 x 480
SVGA
800 x 600
XGA
1024 x 768
WXGA
SXGA
SXGA+
UXGA
1080p
1360 x 768
1280 x 1024
1400 x 1050
1600 x 1200
1920 x 1080
Horizontal Vertical
VESA
Frequency Frequency Standard
31.5 kHz
31.5 kHz
37.9 kHz
37.5 kHz
35.1 kHz
37.9 kHz
48.1 kHz
46.9 kHz
48.4 kHz
56.5 kHz
60.0 kHz
47.7 kHz
64.0 kHz
65.3 kHz
75.0 kHz
67.5 kHz
70 Hz
60 Hz
72 Hz
75 Hz
56 Hz
60 Hz
72 Hz
75 Hz
60 Hz
70 Hz
75 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
O
O
O
O
O
O
O
O
O
O
O
O
O
O
VGA and XGA are registered trademarks of International
Business Machines Corp.
67
2012/04/06 16:50:02
Using a PC
Control of the TV
• The TV can be controlled from a PC, control panels
and other devices using the RS-232C or IP.
• Use a cross-type RS-232C cable, ETHERNET cable
(commercially available) or wireless LAN for the
connections.
• This operation system should be used by a person who is
accustomed to using computers.
AQUOS Remote Control
Example
Initial
Setup
TCP/IP
Set the IP address on the TV menu
None (Do not select Telnet or SSH)
Set a port number on the TV menu
(Control port)
When you set your ID and password on the TV menu, you
need to enter them as soon as you connect to the TV.
• When you use this function, make settings for "AQUOS
Remote Control".
• The connection will be cut off when there has been no
communication for 3 minutes.
EZ Setup
Broadcasting Setup
Internet Setup
Language
[English]
DivX ® Setup
1 Press MENU to display the MENU screen, and then
3
IP protocol:
Host IP address:
Service:
TCP port#:
Menu
Initial Setup
2
Communication Conditions for IP
Connect to the TV with the following settings made for
IP on the PC.
press c/d to select "Initial Setup".
Press a/b to select "Internet Setup", and then
press ENTER.
Press a/b to select "AQUOS Remote Control",
and then press ENTER.
■ AQUOS Remote Control
Set this when operating the TV from equipment
connected by LAN or wireless LAN.
• When "AQUOS Remote Control" is selected, "Change" will
be highlighted. Press ENTER.
Enable: Allows operation from the connected equipment.
Disable: This function does not work.
■ Select Device Names
Set the name of the TV displayed on the portable
device.
Communication Conditions for RS-232C
Set the RS-232C communication settings on the PC to
match the TV's communication conditions.
The TV's communication settings are as follows:
Baud rate:
Data length:
Parity bit:
Stop bit:
Flow control:
9,600 bps
8 bits
None
1 bit
None
■ Communication procedure
Send the control commands from the PC via the RS232C or IP.
The TV operates according to the received command
and sends a response message to the PC.
Do not send multiple commands at the same time.
Wait until the PC receives the OK response before
sending the next command.
■ Command format
Eight ASCII codes e CR
C1 C2 C3 C4 P1 P2 P3
P4
• Use the software keyboard to set the name. See page 73
for details on the software keyboard.
Command 4-digits
■ Detailed Settings
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter 0–9, x, blank, ?
Make the detailed settings (Login ID, password, etc.).
Follow the on-screen instructions to configure the
settings.
Parameter 4-digits
Return code
■ Parameter
Input the parameter values, aligning left, and fill with
blank(s) for the remainder. (Be sure that 4 values are
input for the parameter.)
When the input parameter is not within an adjustable
range, “ERR” returns. (Refer to “Response code format”.)
Any numerical value can replace the “x” on the table.
0
0
0
0
a
3
0
9
When “?” is input for some
commands, the
?
present setting
value responds.
?
?
?
?
■ Response code format
Normal response
O
K
Problem response (communication
error or incorrect command)
E
68
LC-90LE745U_E.indb 68
Return code (0DH)
R
R
Return code (0DH)
2012/04/06 16:50:02
Using a PC
■ Command table
• Commands not indicated here are not guaranteed to operate.
CONTROL ITEM
POWER ON COMMAND SETTING
COMMAND PARAMETER
R S P W 0 _ _ _ Off
1 _ _ _ On [RS-232C]
2 _ _ _ On [IP]
POWER SETTING
P O W R 0
1
I T G D x
I T V D 0
I A V D *
_
_
_
_
_
_
_
_
_
_
A V M D
*
*
*
1: HDMI 1, 2: HDMI 2, 3: HDMI 3, 4: HDMI 4,
5: COMPONENT, 6: VIDEO 1, 7: VIDEO 2, 8: PC
_ 0: (Toggle), 1: STANDARD, 2: MOVIE, 3: GAME,
4: USER, 5: DYNAMIC (Fixed), 6: DYNAMIC, 7: PC,
14: STANDARD (3D), 15: MOVIE (3D),
16: GAME (3D), 100: AUTO
VIEW MODE
V
H
V
C
P
W
M
S
S
K
E
E
*
*
*
*
*
*
*
*
*
*
*
*
_
*
*
*
_
_
_
_
_
_
_
_
MUTE
SURROUND
M U T E
A C S U
*
*
_
_
_
_
_ 0: (Toggle), 1: On, 2: Off
_ 0: (Toggle), 1: Normal, 2: Off, 4: 3D Hall, 5: 3D Movie,
6: 3D Standard, 7: 3D Stadium
AUDIO SELECTION
SLEEP TIMER
A C H A x
O F T M *
_
_
_
_
D C C H
*
*
*
_ (Toggle)
_ 0: Off, 1: OFF TIMER – 30 MIN., 2: OFF TIMER – 60 MIN.,
3: OFF TIMER – 90 MIN., 4: OFF TIMER – 120 MIN.
_ The channel number of TV
(1–135)
D A 2 P
D C 2 U
*
*
*
*
*
*
* (0100-9999)
_ (1-999)
D C 2 L
*
*
*
_ (0-999)
CC
DEVICE NAME
MODEL NAME
SOFTWARE VERSION
D
D
C
C
C
T
M
S
*
*
x
x
x
1
1
1
*
*
_
_
_
_
_
_
*
*
_
_
_
_
_
_
*
*
_
_
_
_
_
_
IP PROTOCOL VERSION
3D
I P P V 1
T D C H *
_
_
_
_
_
_ 0: 3D Off
1: 2D➝3D
2: SBS
3: TAB
4: 3D➝2D (SBS)
5: 3D➝2D (TAB)
6: 3D auto
7: 2D auto
REMOTE CONTROL BUTTONS
R C K Y
*
_
_ 0-9: 0-9, 10: DOT, 11: ENT, 12: POWER, 13: DISPLAY,
14: POWER (SOURCE) 15: *, 16: ,, 17: -,
, 20: +, 21: /
, 22: (REC,
18: ), 19: .
23: OPTION, 24: SLEEP, 27: CC, 28: AV MODE,
29: VIEW MODE, 30: FLASHBACK, 31: MUTE,
32: VOL -, 33: VOL +, 34: CH U, 35: CH V,
36: INPUT, 38: MENU, 39: SmartCentral, 40: ENTER,
41: a, 42: b, 43: c, 44: d, 45: RETURN, 46: EXIT,
47: FAVORITE CH, 48: 3D Surround, 49: AUDIO,
50: A (red), 51: B (green), 52: C (blue), 53: D (yellow),
54: FREEZE, 55: FAV APP 1, 56: FAV APP 2,
57: FAV APP 3, 58: 3D, 59: NETFLIX
INPUT SELECTION
TOGGLE
TV
1-8
AV MODE SELECTION
VOLUME
POSITION
CHANNEL
H-POSITION
V-POSITION
CLOCK
PHASE
DIRECT
CHANNEL
(ANALOG)
DIRECT
CHANNEL
(DIGITAL)
CH UP
CH DOWN
O
P
P
L
H
I
C
C
H
H
L
V
N
W
L
O
O
C
S
D
1
1
U
D
C
N
R
V
0
1
P
W
P
M
D
N
*
_
_
_
_
_
Power Off
Power On
(Toggle)
CONTROL CONTENTS
The Power On command rejected.
The Power On command accepted.
The Power On command accepted.
When the power is in standby mode, commands also go to waiting status
and so power consumption is just about the same as usual. With the
commands in waiting status, the Center Icon Illumination on the front of the
TV lights up.
It shifts to standby.
Power On
It input-switches by the toggle. (It is the same as an input change key)
It input-switches to TV. (A channel remains as it is. (Last memory))
Although it can choose now, it is toggle operation in inside.
Volume (0–60)
The screen position variable ranges depend on the View Mode or the
signal type. The ranges can be seen on the position-setting screen.
Only PC mode. (0–180)
Only PC mode. (0–40)
0: (Toggle) [AV], 1: Side Bar [AV], 2: S.Stretch [AV]
3: Zoom [AV], 4: Stretch [AV], 5: Normal [PC]
6: Zoom [PC], 7: Stretch [PC],
8: Dot by Dot [PC] [AV], 9: Full Screen [AV]
10: Auto [USB-Video, DLNA-Video or Internet applications],
11: Original [USB-Video, DLNA-Video or Internet applications]
(0-9999)
(0-6383)
The channel number of TV +1
The channel number of TV –1
(Toggle)
0: Although it can choose now, it is toggle operation in inside.
1: Only available when 4:3 signal is being input.
5, 6: Only available when 4:3 signal is being input.
8: [PC] Available except when UXGA is being input.
[AV] Only available when 1080i/p is being input.
9: Only available when 720p is being input.
10, 11: Available when USB-Video, DLNA-Video or Internet application is used.
An input change is included if it is not TV display.
In Air, 2–69ch is effective.
In Cable, 1–135ch is effective.
DIGITAL Air (Two-Part numbers, 2-digit plus 2-digit)
DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)
Front half of DIGITAL CABLE CHANNEL NO. (Designate major channel)
DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)
Rear half of DIGITAL CABLE CHANNEL NO. (Designate minor channel)
DIGITAL Cable (One-Part numbers, 5-digit, less than 10,000)
DIGITAL Cable (One-Part numbers, 5-digit, more than 10,000)
If it is not TV display, it will input-switch to TV. (same function as CHU)
If it is not TV display, it will input-switch to TV. (same function as CHV)
Toggle operation of a closed caption.
The device name set in "IP Control Setup" is displayed.
The model name of the TV
The current version of the TV software is displayed.
The currently supported version of IP protocol is displayed.
• If an underbar (_) appears in the parameter column, enter a space.
• If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.
• Any numerical value can replace the “x” on the table.
69
LC-90LE745U_E.indb 69
2012/04/06 16:50:02
Using the Internet
By connecting your TV to a broadband system, you can access the Internet from the TV.
• Use "AQUOS ADVANTAGE LIVE" to obtain the latest software and receive online user support. (See page 72.)
• You can enjoy a variety of streaming content and Internet applications. (See page 76.)
• You may not be able to view 3D images when accessing the Internet.
Connecting to the Internet
• To connect your TV to the Internet, you must have a broadband Internet connection.
• If you do not have a broadband Internet connection, consult the store where you purchased your TV or ask your
Internet service provider or telephone company.
• When an Internet connection is made, an Ethernet and wireless connection cannot be used at the same time.
Use only one of the connection types. (See page 71.)
+Using an ETHERNET cable
Use an ETHERNET cable (commercially available) to connect the ETHERNET terminal on the TV to your broadband
router (commercially available).
ETHERNET cable
LAN
PC
Broadband router
Modem
Internet
+Using
the wireless LAN
This TV is equipped with a wireless LAN function.
For a wireless LAN connection, you must use "Wireless Setup" to connect the access point and TV. (See page 71.)
PC
Wireless LAN router/
access point
Modem
Internet
• This TV has a built-in wireless LAN function. Using a separate wireless USB LAN adapter may result in radio communications
that do not comply with regulations on radio communications. Therefore, do not use a separate wireless LAN adapter.
• A wireless LAN connection and performance cannot be guaranteed for all residential environments. In the following cases, the
wireless LAN signal may be poor or drop, or the connection speed may become slower.
- When used in buildings made with concrete, reinforced steel, or metal
- When placed near objects that obstruct the signal
- When used with other wireless devices that emit the same frequency
- When used in the vicinity of microwave ovens and other devices that emit a magnetic field, electrostatic charge, or
electromagnetic interference
• When there is significant interference in the 2.4-GHz frequency (such as from other wireless LAN devices, Bluetooth® devices,
2.4-GHz cordless telephones, and microwave ovens), it is recommended that you use a wireless LAN router/access point that
supports IEEE802.11a/n (5 GHz) and set the access point to transmit at 5 GHz. For setup details, see the operation manual of
your access point.
70
LC-90LE745U_E.indb 70
2012/04/06 16:50:02
Using the Internet
Internet Setup
Example
Initial
Setup
Menu
5 Press a/b to select "Push button", and then press
ENTER.
• To configure the setting via PC, select "PIN code".
Follow the on-screen instructions and the operation
manual of the access point to configure the settings.
6 Select "Next" to complete the settings.
• The connection process starts and the WPS button on
the access point can be pressed.
Initial Setup
7 Press the WPS button on the access point.
EZ Setup
• Pressing the WPS button displays a confirmation
screen. Please wait until a connection is established.
Broadcasting Setup
8 When a connection is established, the connection
Internet Setup
details are displayed. Press ENTER.
Language
[English]
DivX ® Setup
Connection Type
1 Press MENU to display the MENU screen, and then
2
3
4
press c/d to select "Initial Setup".
Press a/b to select "Internet Setup", and then
press ENTER.
Press a/b to select "Network Setup", and then
press ENTER.
Press a/b to select "Manual Setup", and then
press ENTER.
5 Press c/d to select “Yes”, and then press
6
ENTER.
Press a/b to select "Connection Type", and then
press ENTER.
7 Press c/d to select "Wired" or "Wireless", and
then press ENTER.
• If you select "Wired", the signal is detected and setup
is performed automatically. Use "IP Setup" to check
and change the settings as necessary. (See page 72.)
• If you select "Wireless", use "Wireless Setup" to
configure the access point settings.
Wireless Setup
If your access point supports Wi-Fi Protected Setup
(WPS), it is recommended that you use this function
for the wireless connection. You can press the WPS
button on the access point to configure the settings
automatically.
• The name of the WPS button function may differ depending
on the access point. See the operation manual of the
access point for details.
1 Confirm the current settings in "Connection Type".
• Operations cannot be guaranteed when used with access
points that do not have Wi-Fi® certification.
• A wireless LAN router/access point is required to connect
the TV to the Internet using a wireless LAN. See the
operation manual of your access point for setup.
• If your access point is set to a stealth mode (that prevents
detection by other devices), you may not be able to
establish a connection. In this case, disable the stealth
mode on the access point.
• A stable connection speed is required to play back
streaming content. Use an Ethernet connection if the
wireless LAN speed is unstable.
• Before transferring to a third party or disposal, be sure to
initialize the wireless LAN settings.
• Please follow the legislation in your country when using the
wireless LAN outdoors.
Interactive Service
If you do not want other people to connect to the
Internet in your absence, you can make settings to
keep the TV away from the Internet.
1 Press MENU to display the MENU screen, and then
press c/d to select “Initial Setup”.
2 Press a/b to select “Internet Setup”, and then
press ENTER.
3 Press a/b to select “Interactive Service”, and then
press ENTER.
• Input the 4-digit secret number by using 0-9.
4 Press c/d to select “No”, and then press ENTER.
• If you want to allow Internet connection, select “Yes”,
and then press ENTER.
5 Press MENU to exit.
• If "Wired" is selected, press c/d to select "Wireless".
2 Press a/b to select "Wireless Setup", and then
press ENTER.
• Confirm the settings. If each setting item is correct,
press MENU to exit.
• If you are configuring the wireless setup for the first
time or changing the settings, go to step 3.
3 Press c/d to select "Change", and then press
ENTER.
4 Press a/b to select "WPS", and then press
ENTER.
• To select and register an access point manually, select
"Search" or "Manual Setup" and make the necessary
settings.
71
LC-90LE745U_E.indb 71
2012/04/06 16:50:02
Using the Internet
Checking Your Internet Connection
1 Press SmartCentral to display the application
2
window.
Press c/d to select "AQUOS ADVANTAGE LIVE",
and then press ENTER.
AQUOS Advantage Live
This function can be used to display up-to-date
information and allow you to receive support service
over the network.
• If "
" or "
" is displayed after you connect to
the Internet, check your TV's network settings and
connection.
• When the AQUOS ADVANTAGE LIVE screen appears,
now you are connected to the Internet.
• You can also display the AQUOS ADVANTAGE LIVE
screen by pressing FAV APP on the remote control
unit. See page 76 for details.
• If you have failed to connect to the Internet in the above
operation, then an error message will appear. In this case,
press EXIT to exit from the connected TV feature to make
changes to the network settings.
• If you still cannot connect to the Internet, please consult
your Internet service provider or telephone company.
• When an application is used, you cannot make settings for
"Internet Setup".
If you need to make the settings of "Internet Setup", press
EXIT to exit from the connected TV feature.
+If
you cannot connect to the Internet
Perform the procedures below to check your TV's
network settings.
IP Setup
1 Press SmartCentral to display the application
2
window.
Press c/d to select "AQUOS ADVANTAGE LIVE",
and then press ENTER.
• You can also display the AQUOS ADVANTAGE LIVE
screen by pressing FAV APP on the remote control
unit. See page 76 for details.
• When you are not connected to the Internet, a network
function explanation screen is displayed.
The services displayed vary depending on
circumstances.
3 Press a/b/c/d to select the desired service.
4 Press EXIT to exit from the connected TV feature.
• The display may change as a result of a software update.
1 Press EXIT to exit from the connected TV feature.
2 Press MENU to display the MENU screen, and then
3
4
5
6
7
press c/d to select “Initial Setup”.
Press a/b to select “Internet Setup”, and then
press ENTER.
Press a/b to select “Network Setup”, and then
press ENTER.
Press a/b to select "Manual Setup", and then
press ENTER.
Press c/d to select “Yes”, and then press
ENTER.
Press a/b to select “IP Setup”, and then press
ENTER.
• Check that numbers are displayed for each setting.
• If there are any settings without numbers, specify the
numbers by following the on-screen instructions.
• For information on how to enter text, see page 73.
Example
Setting IP information
[Current Setup]
IP Address
Netmask
Gateway
DNS
MAC Address
:
:
:
:
:
Auto Setup
Auto Setup
Auto Setup
Auto Setup
XX:XX:XX:XX:XX:XX
Change
Initialize
8 Press MENU to exit.
72
LC-90LE745U_E.indb 72
2012/04/06 16:50:02
Using the Internet
Entering Text (Software Keyboard)
When you are editing an input screen or specifying the
Ethernet settings used for accessing the Internet, enter
text from the software keyboard.
• You can enter up to 128 characters for text.
• Some special characters or diacritics may not be available
depending on where you enter the text.
The text you enter is displayed as you type it in.
To move the cursor (the current input position), use
” or “
” on the software keyboard.
“
Press c/d to select the type of characters entered:
alphabet, number or sign.
(The selectable types depend on the input source.)
Caps Off/Caps On/Caps Lock
If “alphabet” is selected in “Character Set”, this switches
characters between uppercase and lowercase.
Each time you press ENTER, the character type switches as
shown below:
Caps Off: all the characters are lowercased
Caps On: only the first character is uppercased
Caps Lock: all the characters are uppercased
Done
Applies the entered information and closes the software
keyboard.
Quit
Closes the software keyboard without applying the entered
information.
• You can also close the software keyboard by pressing
EXIT on the remote control unit.
Displays the icon “
inserted.
”, indicating that a new line has been
Clear
Erases the character string.
• When the cursor is somewhere in a line: the character
string to the right of the cursor will be erased.
• When the cursor is at the right end of a line: the entire line
will be erased.
Delete
If the cursor is at the right end of a line, this erases text one
character at a time.
• You can also delete text by pressing RETURN on the
remote control unit.
Enters a space.
While you are entering text, likely input conversion candidates
are displayed based on what you typed in.
• You can also enter text by pressing A, B or C on the remote
control unit.
Buttons
a
b
c
d
ENTER
EXIT
RETURN
0-9
A (red)
B (green)
C (blue)
D (yellow)
Description
Moves the focus up. When the focus is at the top edge, this moves the focus to
the opposite edge (bottom edge).
Moves the focus down. When the focus is at the bottom edge, this moves the
focus to the opposite edge (top edge).
Moves the focus left. When the focus is at the left edge, this moves the focus to
the opposite edge (right edge).
When the focus is on “Character Set”, this selects the character type (moving
backwards).
When the focus is in an input box, this moves the cursor in the input box to the left.
Moves the focus right. When the focus is at the right edge, this moves the focus to
the opposite edge (left edge).
When the focus is on “Character Set”, this selects the character type (moving
forwards).
When the focus is in an input box, this moves the cursor in the input box to the right.
Performs the processing for the button currently in the focus.
Closes the software keyboard without applying the original input elements for the
entered text.
Erases the text in the input box where the cursor is currently located.
When the cursor is at the end of a sentence, this acts as a backspace.
Directly enters the single-byte number for that button.
Directly enters prediction candidate 1.
Directly enters prediction candidate 2.
Directly enters prediction candidate 3.
Enters a space.
73
LC-90LE745U_E.indb 73
2012/04/06 16:50:03
Using the Internet
Using the Browser
ENTER, a/b/c/d
• Press a/b/c/d to select a link that you want to jump,
and then press ENTER.
EXIT
• Press the button to return to the TV screen.
RETURN
• Press the button to return to the previous page.
D
About links
• Web pages on the Internet often include “links” that
allow you to jump to other web pages (or sites).
• “Links” can take various forms, including words
or images, but they always work in the same way
letting you jump to the link destination when you
select them.
• Selected items (such as links of text input fields) are
enclosed in a frame.
• You can jump from a “link” to the corresponding link
destination.
DISCLAIMERS
SHARP corporation bears no responsibility
regarding the content and quality of the content
provided by the content serve provider.
CAUTION
• Display the toolbar.
• If the power is cut due to a power failure or the TV being
unplugged while you are using the Internet, information
such as bookmarks or cookies may not be saved correctly.
http://xxxxxx.com
D Tools
Pages with security protection are
clearly shown as such.
If content on a page is continued on another page,
you can use a/b/c/d to go to the continuation of a
page.
• Where there is link text or a link image in the
direction pressed, the text or image is selected first.
If this happens, press the same direction button
several times.
Tool bar
Selected item
Description
Allows you to go back to the previous
page.
Allows you to go to the next page.
Refreshes the page.
Interrupts a page while it is loading.
Displays the bookmarks list.
When a security notification window is displayed:
• Press ENTER to close the window.
• This window appears when you visit a web page that has
security protection, or when you move from a protected
page to an unprotected page.
• In “Security” you can set whether or not this window is
displayed. (See page 75.)
To users who access the Internet from a PC
• When you access the Internet from this TV, the
procedures may not be the same as regular
browser-based access on a PC.
• You cannot download files.
• You cannot view a history of the pages you have
visited.
• You cannot change the startup page displayed
when you start AQUOS ADVANTAGE LIVE.
• If a pop-up window has appeared as a new page,
select “ ” on the toolbar and you can return to
the previous page.
• On some pages, video and audio, text or images
may not be displayed correctly.
Displays the AQUOS ADVANTAGE LIVE.
Displays the Browser menu.
Adds the current page to your bookmarks.
http://www.espial.com
74
LC-90LE745U_E.indb 74
2012/04/06 16:50:03
Using the Internet
Using the Toolbar
Browser Settings
You can use the toolbar to control the browser and to
specify settings.
1 Press D to display the toolbar.
2 Press c/d to select a function, and then press
ENTER.
Saving the URL of the Current Page
You can check or modify your browser settings from
the Browser menu.
1 Press D to display the toolbar.
2 Press c/d to select “ ” in the toolbar, and then
press ENTER.
3 Press a/b to select and confirm the item you want
to set.
Adding a web page to your bookmarks allows you to
return to that page later by simply selecting it from your
list of bookmarks.
1 Display the page that you want to bookmark.
4 Press a/b/c/d to specify the required setting,
2 Press D to display the toolbar.
3 Press c/d to select “ ” in the toolbar, and then
Zoom In/Out:
Zoom in: Displays content enlarged to 200%.
Normal: Displays content at 100%.
Zoom out: Displays content reduced to 75%.
Encoding: You can select the desired encoding from the list
below:
Western (ISO-8859-1)/Unicode (UTF-8)
Page Information: Displays information about the currently
displayed page.
Security:
Notify me of secure/non-secure page changes:
If you select this option, a message is displayed
when you move between a protected page and an
unprotected page.
Root Certificates/CA Certificates: Displays the list
of certificates. You can choose to enable/disable a
certificate.
• Disabled certificates are shown unticked in the
certificate list screen.
Cookies:
Accept all: Select this option to accept all cookies.
Reject all: Select this option when you do not want to
accept cookies.
Delete All Cookies: Deletes all your cookies.
Reset:
Resets the browser settings.
press ENTER.
4 Select “Yes”, and then press ENTER.
• The page is added to your bookmarks.
Opening a Bookmarked Page
1 Press D to display the toolbar.
2 Press c/d to select “ ” in the toolbar, and then
press ENTER.
• Your bookmarks list is displayed.
3 Press a/b/c/d to select the page you want to
access, and then press ENTER.
• The selected page is displayed.
• You can edit and delete bookmarks.
Browsing Web Contents
You can display the web content you want to enjoy.
1 Press D to display the toolbar.
2 Press c/d to move to the address area in the
toolbar, and then press ENTER.
• The Enter Address menu is displayed.
3 Enter an address and select "
ENTER.
and then press ENTER.
5 Press D to exit.
", and then press
• The web content you want to view is displayed.
• “Reset” does not reset the certification enable/disable and
Encoding settings.
75
LC-90LE745U_E.indb 75
2012/04/06 16:50:03
Using the Internet
Using Applications via the Internet
By connecting the TV to the Internet, you can enjoy a
variety of broadband content, including videos, music
and photos.
Please check that the most current software is
loaded on TV by selecting "Auto Update Setting" on
"Software Update" (see page 40) or by visiting
http://www.sharpusa.com/products/support/
to check for a download of the newest software version.
■ Move the Icons
You can move the icons of the more commonly used
applications closer to the left.
Press c/d to move the icon to the desired location.
■ Delete an Application
Select "Delete App" to delete the icon.
■ Saving Favorite Applications
You can set your favorite applications to the FAV
APP1, 2, and 3 buttons on the remote control for
easier startup.
The applications whose icons are moved onto 1, 2
and 3 during Dock Display will be assigned to the
FAV APP 1, 2 and 3 buttons respectively.
• The SmartCentral icon cannot be moved or deleted.
During Gallery Display
During Dock display, press SmartCentral again to
display a list of applications by category.
XXXXX
Use the application window to access your favorite
Internet applications. Press SmartCentral to display
the application window.
Follow the on-screen instructions for each application.
• When using this TV to access an Internet application for the
first time, the Disclaimer appears on the screen.
Press a/b to select "Agree", and then press ENTER. (You
must select "Agree" to use the application.)
• Check the web site of the provider for details on setup and
use of the functions.
Featured
Video
Social
Web & Search
Other Apps
Support
App1
App2
App3
App4
App5
App6
App7
App8
App9
App10
App11
App12
App13
App14
App15
Select
ENTER
Enter
RETURN
Back
EXIT
Exit
1 Press c/d to select a category, and then press
ENTER or b.
• If "
" or "
" is displayed after you connect to the
Internet, check your TV's network settings and connection.
• Additional applications will be available in the future.
• These applications are provided by content providers. The
available applications vary depending on your country or
region.
• The delivery speed of applications varies depending on
the network speed. Check the web site of the provider for
details on application setup and other information.
Using the Application Window
During Dock Display
You can move the application icons and delete any
unused icons.
2 Press a/b/c/d to select an application, and then
press ENTER.
1 Displays a list of applications for the selected
category that can be displayed on the TV.
Press ENTER to add or delete applications to
or from the application window and favorites.
2 Displays the image now playing.
3 Provides a description of the selected
application.
4 Displayed when there are multiple pages. Press
c/d to change pages.
5 Guide display of required operation buttons.
Example
1
2
1 Select an application, and then press a.
2 Press a/b to select "Move App" or "Delete App",
and then press ENTER.
76
LC-90LE745U_E.indb 76
2012/04/06 16:50:03
Using the Internet
Example
Information
Menu
Information
Identification
Digital Caption Info.
Software Update
Netflix Help
VUDU Help
Deactivating Netflix Function
1 Press MENU to display the MENU screen.
2 Press c/d to select "Information", and then press
ENTER.
3 Press a/b to select "Netflix Help", and then press
ENTER.
4 Press c/d to select "Deactivate", and then press
ENTER.
• To confirm the Netflix status, check the information
displayed on the screen and click "OK".
Deactivating the VUDU Function
1 Press MENU to display the MENU screen.
2 Press c/d to select "Information", and then press
ENTER.
3
Press a/b to select "VUDU Help", and then press
ENTER.
4 Press c/d to select "Yes", and then press
ENTER.
77
LC-90LE745U_E.indb 77
2012/04/06 16:50:03
Using the Internet
Enjoying Skype™
Getting Started
With Skype™ on your TV, you can enjoy large screen
video calls.
• It is free to create a Skype account and make Skype-toSkype voice and video calls.
• Skype is not a replacement for your telephone and cannot
be used for emergency calls.
• For detailed Skype information, please visit the following
website:
http://www.skype.com/
• Calling phones and mobiles, sending SMS (short message
service) mail and saving instant messages are not possible.
• You might not be able to enjoy Skype on the TV while using
a specific function. In such cases, stop using the function.
• Depending on the Skype version being used by the contact
you are calling, you may not be able to perform some
operations.
• Before using Skype, check "Terms of Use". (See page 81.)
Preparation
To use Skype, you must first make sure you have the
following:
• A broadband Internet connection
• Communication camera for Skype
• A registered Skype account, or an e-mail address to create
a new Skype account
Connecting the Communication Camera
1 Connect the communication camera directly to the
USB 1 or USB 2 terminal on the TV.
• Do not use a USB hub.
• Set the communication camera on the top left of the TV.
Selecting Skype on the Application Window
2 Press SmartCentral to display the application
window.
3 Press c/d to select "
ENTER.
", and then press
• The Welcome to Skype screen is displayed.
• When using this TV to access Skype for the first time,
the Terms of Use appears on the screen.
Press a/b to select "Agree", and then press ENTER.
(You must select "Agree" to use the application.)
• Depending on the network environment used, transmission
qualities of voice or pictures may deteriorate.
Buying the communication camera
Follow the guidance found on the website below and
purchase a communication camera compatible with Skype.
http://freetalk.me/product/sharp/
• The Skype FREETALK® Communication camera is not
supplied by Sharp.
• Other cameras and webcams are not compatible with your
TV.
• If the Welcome to Skype screen is not displayed, check the
network connection.
Creating a New Skype Account
• If you already have a Skype account, you can use that
account. (Go to step 8 in Sign In to Skype.)
4 Select "Don't have a Skype Name? " on the
Welcome to Skype screen, and then press ENTER.
5 The Create a new Skype account screen will appear.
If you agree to all of the terms and conditions,
select "Accept", and then press ENTER.
• For more information on the terms and conditions, refer to
the following:
- Skype Terms of Service
(http://www.skype.com/intl/en/legal/terms/tou)
- Skype Privacy Statement
(http://www.skype.com/legal/privacy/general)
78
LC-90LE745U_E.indb 78
2012/04/06 16:50:03
Using the Internet
6 Enter your "Full name", "Skype Name", "Password",
Adding Your Friends to Your Contact list
and "Email" address.
• If this is not your first time using Skype, your previously
registered contacts will appear.
1 Select "Contacts" on the Skype main menu, and
7 Select "Create Account", and then press ENTER.
then press ENTER.
2 Press D (add contact).
Sign In to Skype
8 Enter your registered "Skype Name" and "Password".
9 Select "Sign in", and then press ENTER.
• If you have signed in on the TV before:
1 Select the "Skype Name", and then press ENTER.
2 Select your Skype name from the recently used
accounts, and then press ENTER.
• By ticking the "Sign me in when Skype starts", you can
enable automatic sign in.
3 Enter the Skype name, E-mail address, or full name
of the person you want to add.
Using Skype™
4 Select "Search", and then press ENTER.
5 Select the person you want to add from the search
Skype Main Menu
result, and then press ENTER.
Claire
6 With the software keyboard, enter a message to
introduce yourself and send it with "Done".
• "Contact requests" will be sent to the person added to
the Contact list.
Selecting a Contact and Starting a Video Call
1 Your Skype Name, online status*, Skype credit and
profile picture
2 The picture from your communication camera
3 Notification area
4 Menu items: "Contacts", "History", "Profile" and
"Settings"
* Status icons
Icon
Status
1 Select "Contacts" in the Skype main menu, and
then press ENTER.
2 Select a contact who is online from your list of
Contacts, and then press ENTER.
Online
Away
Do not disturb
Invisible/Offline
79
LC-90LE745U_E.indb 79
2012/04/06 16:50:03
Using the Internet
3 Select "Video call" on the Contacts Option menu,
Receiving Skype Calls
and then press ENTER.
• If you want to make a voice call, select "Call".
Contact Option menu
Video call: Make a video call.
Call: Make a voice call.
View profile: View the selected contact's profile.
Rename: Rename the selected person.
Block/Unblock: Block/Unblock selected person from
contacting you.
Send Voicemail: Send a voicemail message to the
selected contact. (Voicemail is a paid service. Visit the
following website for more information: http://www.
skype.com/)
Remove: Remove the person from your Contacts list.
■ Video Call Screen (Normal View)
Claire
You can receive Skype calls even while watching a TV
program or video.
When you receive an incoming call, a window will
appear in the bottom right-hand corner of the screen.
Select "Video", "Audio", "Decline" or "Hide", and then
press ENTER.
Incoming call
Kevin
Video
Audio
Decline
Hide
• You cannot receive calls when you are signed out of Skype,
when the TV is in standby mode, or when the power is off.
• Skype on the TV cannot be activated while you are using
a certain specific function. In that case, stop using the
function.
Other Useful Functions
On the Skype main menu, you can manage and adjust
your call history.
■ History
1 Video call menu*
2 The picture from contact person's communication
camera
3 The picture from your communication camera
4 Video quality indicator
(Depending on the network environment)
* Video call menu
Once a video call has started, the following items will
be available.
• End call
• Hold/Resume
• Dial pad
• Mute/Unmute (microphone)
• Stop my video/Start my video
• Full view
• To change the speaker volume of the unit, press VOL k/l
or MUTE on the remote control.
• Shows your call history.
• Allows you to call a person displayed in Call History and to
accept or block contact requests.
• If the time displayed in History is incorrect, make the
necessary adjustments in Initial Setup > EZ Setup >
Location & Time.
■ Profile
Set up the following items.
Edit profile: Edit your profile.
Online status: Change your online status.
■ Settings
Set up the following items.
General settings: Select whether you want to sign in
automatically when you enter Skype.
Change password: Change your password.
Video settings: Adjust the privacy settings for video.
Privacy settings: Choose whom you wish to receive
calls from.
Block contacts: Set the person who you do not want to
hear.
80
LC-90LE745U_E.indb 80
2012/04/06 16:50:04
Using the Internet
The following will be displayed when you get access to Skype for the first time.
Terms of Use
PLEASE READ CAREFULLY
1. All Skype features are offered by Skype under the terms of the Skype end user license agreement .
2. You shall not promote, include, display, provide, or make available any content which:
(a) may be considered: sexually explicit (including the use of sexual terms, images and nudity);vulgar, profane,
offensive or obscene; defamatory, libellous, slanderous; religiously or racially offensive or otherwise
promoting hate towards individuals or groups; promoting terrorist or other criminal or illegal activities;
promoting gambling, alcohol, tobacco, firearms or ammunition; otherwise unlawful; or
(b) infringes anyone else's intellectual property rights, other proprietary rights or rights of privacy; You
undertake and represent that you own or have sufficient permission to use all content that you include in,
display through, provide, or make available through our product.
3. You are solely responsible for any content that you upload, submit, post, transmit or display through the
Skype on our product -(“ use” or “used”) and that SHARP is not responsible to you or any third party for any
content that is used by you or any other Skype user.
4. You will not reverse engineer or attempt to derive the source code for any Skype software included in our
product, or remove or separate from our product , or copy, redistribute or otherwise provide to any third
parties any Skype software that is included in our product.
5. The Skype features do not support any emergency calls.
6. SHARP will not guarantee that you cannot utilize the Skype features under the following conditions
— In case the malfunction caused by the Skype server happens
— In case the malfunction of the network happens
7. IN NO EVENT SHALL SHARP AND/OR ITS AFFILIATES BE LIABLE, WHETHER IN CONTRACT, WARRANTY,
TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR ANY OTHER FORM OF LIABILITY, FOR:
— SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING WITHOUT LIMITATION ANY LOSS OF OR
CORRUPTION TO DATA, INTERRUPTION, COMPUTER FAILURE OR PECUNIARY LOSS) ARISING OUT
OF THE USE OR INABILITY TO USE THE SKYPE; AND
— ANY LOSS OF INCOME, BUSINESS OR PROFITS (WHETHER DIRECT OR INDIRECT) ARISING OUT OF
THE USE OR INABILITY TO USE THE SKYPE;
— ANY LOSS OR DAMAGE WHICH MAY BE INCURRED BY YOU AS A RESULT OF;
W ANY DISRUPTIONS OR DELAYS IN ANY COMMUNICATION WHEN USING THE SKYPE
8. These Terms of Use supplement and do not replace, any terms, conditions or disclaimers, which were
provided with your purchase of the product. All such terms, conditions and disclaimers remain in full force
and effect.
9. Your use of the Skype on our product constitutes your agreement to be bound by these Terms of Use. You
understand and agree that SHARP will treat your use of the Skype on our product as acceptance of the
Terms of Use from that point onwards.
You agree that the use of the Skype on our product is at your own risk.
81
LC-90LE745U_E.indb 81
2012/04/06 16:50:04
Using the Internet
When you access the Internet application for the first time, the following appears.
• This message is available only in English.
DISCLAIMERS
• This SHARP device facilitates the access to content and services provided by third parties. The content and
services accessible via this device belong to and may be proprietary to third parties. Therefore, any use of
such third party content and services must be in accordance with any authorization or terms of use provided
by such content or service provider. SHARP shall not be liable to you or any third party for your failure to
abide by such authorization or terms of use. Unless otherwise specifically authorized by the applicable content
or service provider, all third party content and services provided are for personal and non-commercial use;
you may not modify, copy, distribute, transmit, display, perform, reproduce, upload, publish, license, create
derivative works from, transfer or sell in any manner or medium any content or services available via this
device.
• SHARP is not responsible, nor liable, for customer service-related issues related to the third party content or
services. Any questions, comments or service-related inquiries relating to the third party content or service
should be made directly to the applicable content or service provider.
You may not be able to access content or services from the device for a variety of reasons which may be
unrelated to the device itself, including, but not limited to, power failure, other Internet connection, or failure
to configure your device properly. SHARP, its directors, officers, employees, agents, contractors and affiliates
shall not be liable to you or any third party with respect to such failures or maintenance outages, regardless of
cause or whether or not it could have been avoided.
• ALL THIRD PARTY CONTENT OR SERVICES ACCESSIBLE VIA THIS DEVICE IS PROVIDED TO YOU
ON AN “AS-IS” AND “AS AVAILABLE” BASIS AND SHARP AND ITS AFFILIATES MAKE NO WARRANTY
OR REPRESENTATION OF ANY KIND TO YOU, EITHER EXPRESS OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, ANY WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, FITNESS FOR
A PARTICULAR PURPOSE OR ANY WARRANTIES OF SUITABILITY, AVAILABILITY, ACCURACY,
COMPLETENESS, SECURITY, TITLE, USEFULNESS, LACK OF NEGLIGENCE OR ERROR-FREE OR
UNINTERRUPTED OPERATION OR USE OF THE CONTENT OR SERVICES PROVIDED TO YOU OR THAT
THE CONTENT OR SERVICES WILL MEET YOUR REQUIREMENTS OR EXPECTATIONS.
• SHARP IS NOT AN AGENT OF AND ASSUMES NO RESPONSIBILITY FOR THE ACTS OR OMISSIONS OF
THIRD PARTY CONTENT OR SERVICE PROVIDERS, NOR ANY ASPECT OF THE CONTENT OR SERVICE
RELATED TO SUCH THIRD PARTY PROVIDERS.
• IN NO EVENT WILL SHARP AND/OR ITS AFFILIATES BE LIABLE TO YOU OR ANY THIRD PARTY FOR
ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE, CONSEQUENTIAL OR OTHER DAMAGES,
WHETHER THE THEORY OF LIABILITY IS BASED ON CONTRACT, TORT, NEGLIGENCE, BREACH OF
WARRANTY, STRICT LIABILITY OR OTHERWISE AND WHETHER OR NOT SHARP AND/OR ITS AFFILIATES
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Examples of Application Logos
82
LC-90LE745U_E_07.indd 82
2012/04/09 15:23:36
Appendix
Removing the Stand
• Before detaching (or attaching) the stand, make sure to turn off the TV and unplug the AC cord.
CAUTION
• Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
1
2
Unfasten the four screws used to secure the stand in
place.
Detach the stand from the TV.
• In the installation procedure, be careful not to catch your fingers between the TV set and the floor.
83
LC-90LE745U_E.indb 83
2012/04/06 16:50:04
Appendix
Setting the TV on the Wall
The wall mount kit (sold separately) allows you to mount the TV on the wall.
For detailed information on installing the wall mount, see the instructions provided with the product. We
recommend you to contact a technician for assistance when installing it.
SHARP is not responsible for any damage to the product or injury to yourself or others if you elect to install the wall
mount on your own.
CAUTION
• Install your wall mount on a solid wall perpendicular to the floor.
When you want to attach the wall mount to surfaces other than plaster board, please contact your nearest
retailer/adviser for additional information. If you install the TV on a ceiling or slanted wall, it may fall and result in
severe personal injury. Always have two people mount the TV on a wall.
Wall Mount Kit Specifications
Standard dimensions for wall mount kits are shown below.
A
WALL
Max 1
37
/64 (40)
Max 13
WALL MOUNT KIT *1
25
/64 (340)
B
/64 (375)
15 3/4 (400) B
7 7/8 (200)
WALL MOUNT KIT *1
23 5/8 (600)
/64 (175)
Max 6
57
Max 14
49
SCREW
WALL MOUNT
UNIT
A
CABINET
1 3/32 (27.8)
Min 3 5/32 (80)
31
MOUNTING
HOLES
• VESA screw hole specs (A - B)
in millimeters
• Standard screw
• Quantity
/64 (12)
DEPTH OF
MOUNTING HOLES
23 5/8 - 15 3/4
(600 - 400)
M8*2
4
*1 Must be smaller than the shaded area.
*2 Use 1.25 pitch screws.
• Do not mount the TV at a tilt.
• Due to the terminal configuration on this TV, when you wall-mount this model, make sure there is enough space
between the wall and the TV for the cables.
• To use this TV mounted on a wall, remove the cable tie as needed.
• Do not use screws that do not comply with the VESA standard screw specifications.
• Do not use screws that are longer than the standard length. Screws that are too long may cause damage to the inside
of the TV set.
• Do not fasten the screws too firmly or loosely. This may damage the product or cause the product to fall, leading to
personal injury. SHARP is not liable for these kinds of accidents.
• SHARP is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or
the consumer fails to follow the product installation instructions.
Do not install the wall mount kit while your TV is turned on. It may result in personal injury due to
electric shock.
84
LC-90LE745U_E.indb 84
2012/04/06 16:50:04
Appendix
Troubleshooting
Problem
Possible Solution
• No power
• Check if you pressed POWER on the remote control unit.
• Is the AC cord disconnected? Page 10
• Has the power been turned on? Page 19
• Unit cannot be operated.
• External influences such as lightning, static electricity, may cause improper
operation. In this case, operate the unit after first turning off the power of the TV or
unplugging the AC cord and replugging it in after 1 or 2 minutes.
• Remote control unit does not
operate.
• Is the equipment to be operated by the remote control unit set correctly? Press TV
to set the remote control unit to the setting for operating the TV.
• Are batteries inserted with polarity (e, f) aligned? Page 11
• Are batteries worn out? (Replace with new batteries.)
• Are you using it under strong or fluorescent lighting?
• Is a fluorescent light illuminated near the remote control sensor?
• Is "RC Control Lock" selected in "Operation Lock Out"? Page 35
• Picture is cut off/with sidebar
screen.
• Is the image position correct? Pages 34 and 67
• Are screen mode adjustments such as picture size made correctly?
Pages 26 and 66
• Strange color, light color, or color
misalignment
• Adjust the picture tone. Pages 29 and 30
• Is the room too bright? The picture may look dark in a room that is too bright.
• Power is suddenly turned off.
• Is the sleep timer set? Page 23
• Check the power control settings. Page 32
• The unit's internal temperature has increased. Remove any objects blocking vent or
clean.
• No sound
•
•
•
•
•
•
•
•
•
•
Page 19
Is connection to other components correct? Pages 14 to 18 and 61
Is the volume too low? Page 23
Is "Variable" selected in "Output Select"? Page 34
Have you pressed MUTE on the remote control unit? Page 23
Check the audio output of the connected external equipment. Is the volume too
low or muted?
When external equipment is connected via an HDMI cable, you may need to
configure the audio to be output through the HDMI cable.
When audio is not output from external equipment connected to the PC IN or HDMI 2
terminal, check the "Audio Select" setting. Page 67
Even when external equipment is connected using an HDMI-certified cable, an audio
cable connection may be required depending on the type of equipment and the
media being played back. In this case, in addition to connecting an HDMI-certified
cable to the HDMI 2 terminal, connect a Ø 3.5 mm stereo minijack cable to the
AUDIO IN terminal and set "Audio Select" to "HDMI+Analog". Page 67
When connecting a PC via an HDMI-certified cable, check the following:
- Is the audio output of the PC configured correctly? Check the audio output
settings and output audio format in Sound Properties on the PC.
The audio formats compatible with this TV are PCM, Dolby Digital. With other
formats, audio cannot be output.
- Depending on the board, only video signals may be output. In this case, in
addition to connecting an HDMI-certified cable to the HDMI 2 terminal, connect a
Ø 3.5 mm stereo minijack cable to the AUDIO IN terminal and set "Audio Select"
to "HDMI+Analog". Page 67
If you are using a DVI-HDMI conversion cable to connect external equipment to the
TV, check the following:
- Is an audio cable connected? The DVI-HDMI conversion cable is for video only.
Connect a Ø 3.5 mm stereo minijack cable to listen to the audio.
- Is HDMI 2 being used? When the TV is connected to another HDMI terminal, the
audio and video are not output together even if a Ø 3.5 mm stereo minijack cable
is connected to the shared AUDIO IN terminal for PC IN and HDMI 2.
- Check the "Audio Select" setting. Set "Audio Select" to "HDMI+Analog". Page 67
85
LC-90LE745U_E.indb 85
2012/04/06 16:50:04
Appendix
Problem
Possible Solution
Is connection to other components correct? Pages 14 to 18 and 61
Is the correct input selected? Pages 14 and 23
Is "On" selected in "Audio Only"? Page 32
If the PC image is not displayed, check the following:
- When connecting a laptop PC to the TV, check that display output mode of the
PC is set to external monitor.
- Check the resolution setting on the PC. Is a non-compatible signal being input?
Page 67
• No picture
•
•
•
•
• Picture quality of HD programs is
poor.
• To enjoy HD images from external equipment, you are required to set up HDMI
connection or component connection.
• If the program content is not of HD quality, HD images cannot be displayed. Check
that the program you are viewing provides HD images.
• The HD cable/satellite set-top box may need to be configured to output HD images
via cable/satellite.
• The cable/satellite broadcast may not support a signal resolution of 1080p.
• The TV sometimes makes a
cracking sound.
• This is not a malfunction. This happens when the cabinet slightly expands and contracts
according to change in temperature. This does not affect the TV's performance.
• The AQUOS ADVANTAGE LIVE
cannot be displayed.
• Is the ETHERNET cable connected correctly? Page 70
• Check the settings of "Internet Setup".
Pages 71 to 72
• Some Internet functions used on a
PC are not available from the TV.
• The TV has only limited functions compared with regular PC browsers.
Page 74
Troubleshooting - 3D Images
Problem
• 3D images are not displayed.
Possible Solution
• Is "3D Auto Change" set to "Off"? Press 3D to switch to 3D mode. Page 49
• If "3D Auto Change" is set to "Mode 1" or "Mode 2" but no 3D images are displayed,
check the display format of the content being viewed. Some 3D image signals may not be
recognized as 3D images automatically. Press 3D to select the appropriate display format
for the 3D image. Pages 47 to 48
• Is the power of the 3D Glasses turned on?
• Are the 3D Glasses set to 2D mode?
• Is there an obstacle between the 3D Glasses and the TV, or is something covering
the infrared receiver on the 3D Glasses? The 3D Glasses operate by receiving a
signal from the TV. Do not place anything between the 3D infrared emitter on the TV
and the infrared receiver on the 3D Glasses. Page 12
For further details, refer to the operation manual of your 3D Glasses.
Troubleshooting - Error Message
The example of an error message
displayed on a screen
Error code
Possible Solution
• Failed to receive broadcast.
E202
• Check the antenna cable. Check that the antenna is correctly setup.
• No broadcast now.
E203
• Check the broadcast time in the program guide.
• An incompatible audio signal has
been received. Check the output
device settings.
—
• This message is displayed when an audio format other than PCM
or Dolby Digital is input. (The DTS audio format is not supported.)
- Set the audio output format of connected external HDMI
equipment to PCM or Dolby Digital.
- Refer to the operation manual of the external equipment for
setting details.
86
LC-90LE745U_E.indb 86
2012/04/06 16:50:04
Trademarks
• SmartCentral is a registered trademark of Sharp Corporation.
• Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
• "HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries."
• DivX®, DivX Certified®, DivX Plus® HD and associated logos are trademarks of Rovi Corporation or its subsidiaries
and are used under license.
• The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance.
• The Wi-Fi Protected Setup Mark is a mark of the Wi-Fi Alliance.
• DLNA®, the DLNA Logo and DLNA CERTIFIED™ are trademarks, service marks, or certification marks of the Digital
Living Network Alliance.
• This product includes DLNA Software 'DiXiM' developed by DigiOn, Inc.
•
and LC logo mark are registered trademarks of SHARP Corporation.
This product is embedded with LC Font technology, which was developed by SHARP Corporation for clearly
displaying easy-to-read characters on LCD screens. However, other fonts are used for some screen pages, too.
• ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This
is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to
convert your files into DivX videos.
• ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX
Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup
menu. Go to vod.divx.com for more information on how to complete your registration.
• Netflix and the Netflix logo are the registered trademarks of Netflix, Inc.
• VUDU™ is a trademark of VUDU, Inc.
• Skype, the Skype Logo and the S logo and other marks indicated on these instructions are trademarks of Skype
Limited or other related companies.
87
LC-90LE745U_E.indb 87
2012/04/06 16:50:04
Specifications
TV
LCD panel
TV
Function
Item
Size
Resolution
TV-standard (CCIR)
VHF/UHF
CATV
Receiving
Digital Terrestrial Broadcast
Channel
(8VSB)
Digital cable*1 (64/256 QAM)
Audio multiplex
Audio out
Back panel
vertical inputs
Terminals
Back panel
surface inputs
HDMI 1
HDMI 2
HDMI 3
HDMI 4
AUDIO OUT
USB 1
COMPONENT
VIDEO 1
VIDEO 2
PC IN
RS-232C
ANT/CABLE
Back panel
horizontal inputs
AUDIO IN
DIGITAL AUDIO OUTPUT
ETHERNET
USB 2
OSD language
Power Requirement
Power Consumption
Weight
Dimensions*2 (W g H g D)
Operating temperature
Model: LC-90LE745U
90o Class (90 1/64o Diagonal)
2,073,600 pixels (1,920 g 1,080)
American TV Standard ATSC/NTSC System
VHF 2-13ch, UHF 14-69ch
1-135ch (non-scrambled channel only)
2-69ch
1-135ch (non-scrambled channel only)
BTSC System
10W g 2 + 15W (WF)
HDMI in with HDCP, ARC
HDMI in with HDCP, Audio in (Ø 3.5 mm stereo jack)
HDMI in with HDCP
HDMI in with HDCP, MHL
Audio out (Ø 3.5 mm stereo jack)
Photo/Music/Video mode, Software update
COMPONENT in
AV in
AV in
ANALOG RGB (PC) in (15-pin mini D-sub female connector),
Audio in (Ø 3.5 mm stereo jack)
9-pin D-sub male connector
75 q Unbalance, F Type g 1 for Analog (VHF/UHF/CATV) and
Digital (AIR/CABLE)
Audio in (Ø 3.5 mm stereo jack)
Optical Digital audio output g 1 (PCM/Dolby Digital)
Network connector
Photo/Music/Video mode, Software update
English/French/Spanish
AC 120 V, 60 Hz
381 W (0.1 W Standby with AC 120 V)
TV + stand
150.0 lbs./68.0 kg
TV only
141.1 lbs./64.0 kg
TV + stand
80 7/8 g 48 61/64 g 17 3/32 inches
TV only
80 7/8 g 47 11/16 g 4 37/64 inches
e32°F to e104°F (0°C to e40°C)
*1
Emergency alert messages via Cable are unreceivable.
The dimensional drawings are shown on the inside back cover.
• As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
*2
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.
This is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the front panel to malfunction.
Storage temperature: f4°F to e140°F (f20°C to e60°C)
88
LC-90LE745U_E.indb 88
2012/04/06 16:50:05
Specifications
Wireless LAN
This TV has received the following certifications.
- Wi-Fi CERTIFIED™ (certification program from the Wi-Fi Alliance® )
- Wi-Fi Protected Setup™ (certification program from the Wi-Fi Alliance® )
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. To comply with the FCC RF exposure compliance
requirements, this device and its antenna must not be co-located or operated in conjunction with any other antenna or
transmitter.
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel
mobile satellite systems;
The maximum antenna gain permitted (for devices in the bands 5250-5350 MHz and 5470-5725 MHz) to comply with the e.i.r.p.
limit; and High-power radars are allocated as primary users (meaning they have priority) of the bands 5250-5350 MHz and
5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.
COFETEL
This equipment operates on a secondary basis and, consequently, must accept harmful interference, including from station of
the same kind, and may not cause harmful interference to systems operating on a primary basis.
CONTAINS TRANSMITTER MODULE COFETEL ID: RCPSHTW11-1252
Brand: SHARP
Model: TWFM-B005D
Specification
IEEE 802.11a/b/g/n
2412-2484 MHz
5150-5850 MHz
Static WEP (64/128 bit key Index 1 only)
WPA-PSK (TKIP)
WPA2-PSK (AES)
DBPSK@1Mbps
DQPSK@2Mbps
CCK@5.5/11Mbps
BPSK@6/9 Mbps
QPSK@12/18Mbps
16-QAM@24Mbps
64-QAM@48/54Mbps and above, Rx up to 300Mbps
Standard
Frequency Band
Security
Modulation
CLEARING THE SECRET NUMBER
If you forget the secret number, clear the secret number using the following procedure.
Select an item from the list below to display the secret number input screen. (For operating the on-screen
display menu, see page 27.)
System Options menu).
• "Color system" ( "Terminal Setting"
• "EZ Setup" or "Reset" ( Initial Setup menu).
• "CH Setup” ( "Broadcasting Setup"
Initial Setup menu).
• "Parental CTRL" ( "Individual Setup"
Initial Setup menu).
• "Interactive Service" ( "Internet Setup"
Initial Setup menu).
• "Software Update" ( Information menu).
Press and hold both CHU and VOLk on the TV simultaneously until the message appears on the screen.
➝
➝
➝
➝
The secret number is
➝
➝
➝
➝
➝
2
➝
1
.
• As a precautionary measure, make a note of your secret number above, and keep it in a safe place.
89
LC-90LE745U_E.indb 89
2012/04/06 16:50:05
Information on the Software License for This Product
■ Software composition
The software included in this product is comprised of various software components whose individual copyrights
are held by SHARP or by third parties.
■ Software developed by SHARP and open source software
The copyrights for the software components and various relevant documents included with this product that were
developed or written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties,
and other relevant laws. This product also makes use of freely distributed software and software components
whose copyrights are held by third parties. These include software components covered by a GNU General Public
License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license agreement.
■ Obtaining source code
Some of the open source software licensors require the distributor to provide the source code with the executable
software components. GPL and LGPL include similar requirements. For information on obtaining the source code
for the open source software and for obtaining the GPL, LGPL, and other license agreement information, visit the
following website:
http://www.sharpusa.com/gpl
We are unable to answer any questions about the source code for the open source software. The source code for
the software components whose copyrights are held by SHARP is not distributed.
■ Acknowledgements
The following are some of the open source software components included in this product:
• linux kernel/busybox/glibc/zlib/libpng/libjpeg/libiconv/DirectFB/OpenSSL/XMLRPC-EPI/mtd-utils/Expat/Qt/
U-Boot/PlayReady/AGG(ver2.3)/device-mapper/libfreetype/cURL/libxml2/lua/lua-xmlreader/lua-slncrypto/
Ffmpeg/SQLite/libzzip/c-ares/librt/libjanus/NTP/webkit/cairo/fontconfig/icu/libxslt/gtk+/atk/pango/glib2/
libpixman
For the complete list, please see the URL above.
■ Software Copyrights
XMLRPC-EPI
Copyright 2000 © Epinions, Inc.
libjpeg
This software is copyright © 1991-2012, Thomas G. Lane, Guido Vollbeding.
Portions of this software are based in part on the work of the Independent JPEG Group.
SSLeay
Copyright © 1995-1998 Eric Young (eay@cryptsoft.com)
This product includes cryptographic software written by Eric Young (eay@cryptsoft.com).
Expat
Copyright © 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper.
Copyright © 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.
Qt
The Qt GUI Toolkit is Copyright © 2010 Nokia Corporation and/or its subsidiary(-ies).
Contact: Nokia Corporation (qt-info@nokia.com)
PlayReady
This product contains technology subject to certain intellectual property rights of Microsoft. Use or
distribution of this technology outside of this product is prohibited without the appropriate lisense(s) from
Microsoft.
Content owners use Microsoft PlayReadyTM content access technology to protect their intellectual
property, including copyrighted content. This device uses PlayReady technology to access PlayReadyprotected content and/or WMDRM-protected content. If the device fails to properly enforce restrictions
on content usage, content owners may require Microsoft to revoke the device’s ability to consume
PlayReady-protected content. Revocation should not affect unprotected content or content protected by
other content access technologies. Content owners may require you to upgrade PlayReady to access
their content. If you decline an upgrade, you will not be able to access content that requires the upgrade.
libfreetype
Copyright © 2006, 2007, 2008, 2009, 2010 by David Turner, Robert Wilhelm, and Werner Lemberg.
The software is based in part of the work of the Free Type Team.
libxml2
Copyright © 1998-2003 Daniel Veillard. All Rights Reserved.
Lua
Copyright © 1994-2008 Lua.org, PUC-Rio
Lua-xmlreader
Copyright © 2008 A.S. Bradbury
Lua-slncrypto
Copyright © 2005 Malete Partner, Berlin, partner@malete.org
90
LC-90LE745U_E.indb 90
2012/04/06 16:50:05
Information on the Software License for This Product
libzzip
Copyright © Guido Draheim guidod@gmx.de
c-ares
Copyright © 1998 by the Massachusetts Institute of Technology.
Group 42
Portions copyright © 2000 Group 42, Inc. and the Contributing Authors.
zlib
Portions copyright © 1995-1996 Jean-loup Gailly and Mark Adler.
RSA Data Security
MD5.CPP - RSA Data Security, Inc., MD5 message-digest algorithm. Copyright © 1991-2, RSA Data
Security, Inc. Created 1991. All rights reserved.
Fraunhofer IIS and Thomson Multimedia
MPEG Layer-3 audio compression technology licensed by Fraunhofer IIS and Thomson Multimedia.
You cannot use the MP3 compressed audio within the Software for real time or live broadcasts.
If you require an MP3 decoder for real time or live broadcasts, you are responsible for obtaining this
MP3 technology license.
Nellymoser, Inc
Speech compression and decompression technology licensed by Nellymoser, Inc.
Sorenson Media, Inc
SorensonTM SparkTM video compression and decompression technology licensed from Sorenson Media,
Inc.
Sun Microsystem, Inc
ADPCM speech compression algorithm is used with the permission of Sun Microsystems, Inc.
NTP
Copyright © University of Delaware 1992-2011
Permission to use, copy, modify, and distribute this software and its documentation for any purpose
with or without fee is hereby granted, provided that the above copyright notice appears in all copies and
that both the copyright notice and this permission notice appear in supporting documentation, and that
the name University of Delaware not be used in advertising or publicity pertaining to distribution of the
software without specific, written prior permission. The University of Delaware makes no representations
about the suitability this software for any purpose. It is provided "as is" without express or implied
warranty.
fontconfig
Copyright © 2001, 2003 Keith Packard
icu
Copyright © 1995-2011 International Business Machines Corporation and others All rights reserved.
libxslt
Copyright © 2001-2002 Daniel Veillard. All Rights Reserved.
cURL
COPYRIGHT AND PERMISSION NOTICE
Copyright © 1996-2009, Daniel Stenberg, <daniel@haxx.se>.
All rights reserved.
Permission to use, copy, modify, and distribute this software for any purpose with or without fee is
hereby granted, provided that the above copyright notice and this permission notice appear in all
copies.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT
SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
THE SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in advertising or
otherwise to promote the sale, use or other dealings in this Software without prior written authorization
of the copyright holder.
libpixman
Copyright © 2008 Free Software Foundation, Inc.
91
LC-90LE745U_E.indb 91
2012/04/06 16:50:05
Information on the Software License for This Product
OpenSSL
LICENSE ISSUES
The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and
the original SSLeay license apply to the toolkit.
See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In
case of any license issues related to OpenSSL please contact openssl-core@openssl.org.
OpenSSL License
Copyright © 1998-2008 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgment:
"This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit.
(http://www.openssl.org/)"
4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote
products derived from this software without prior written permission. For written permission, please
contact openssl-core@openssl.org.
5. Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in
their names without prior written permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain the following acknowledgment:
"This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit
(http://www.openssl.org/)"
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS" AND ANY EXPRESSED OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL
PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT
OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product
includes software written by Tim Hudson (tjh@cryptsoft.com).
Original SSLeay License
Copyright © 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved.
This package is an SSL implementation written by Eric Young (eay@cryptsoft.com).
The implementation was written so as to conform with Netscapes SSL.
This library is free for commercial and non-commercial use as long as the following conditions are
aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA,
lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is
covered by the same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.com).
Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this
package is used in a product, Eric Young should be given attribution as the author of the parts of the library used.
This can be in the form of a textual message at program startup or in documentation (online or textual)
provided with the package.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgement:
"This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)"
The word ‘cryptographic’ can be left out if the rouines from the library being used are not cryptographic related :-).
4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application
code) you must include an acknowledgement:
"This product includes software written by Tim Hudson (tjh@cryptsoft.com)"
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The licence and distribution terms for any publically available version or derivative of this code cannot be changed.
i.e. this code cannot simply be copied and put under another distribution licence
[including the GNU Public Licence.]
92
LC-90LE745U_E.indb 92
2012/04/06 16:50:05
Calling for Service
For location of the nearest Sharp Authorized Service, or to obtain product literature, accessories, supplies, or
customer assistance, please call 1-800-BE-SHARP.
LIMITED WARRANTY
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand Liquid Crystal Display product (the
“Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option,
either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the
purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product or if the serial number or model number affixed to the Product has
been removed, defaced, changed, altered or tampered with. This warranty does not cover installation or signal reception problems. This
limited warranty will not apply if the Product has been or is being used in a commercial setting or application; this warranty is meant solely
for the non-commercial, household use of the Product by consumers in their home or residence. If you intend to or already use this Product
for commercial purposes or in a commercial setting, there are warranties available to cover your use of this Product, the terms of which may
vary. Please contact 1-888-GO-SHARP for further information.
In order to enforce your rights under this limited warranty, you should follow the steps set forth below. You must be able to provide proof of
purchase to the servicer, which proof must include the date of purchase.
To the extent permitted by applicable state law, the warranties set forth are in lieu of, and exclusive of, all other warranties, express or
implied. Specifically ALL OTHER WARRANTIES OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED, ALL EXPRESS AND
IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE, AND FITNESS FOR A PARTICULAR
PURPOSE ARE SPECIFICALLY EXCLUDED. IF, UNDER APPLICABLE STATE LAW, IMPLIED WARRANTIES MAY NOT VALIDLY BE
DISCLAIMED OR EXCLUDED, THE DURATION OF SUCH IMPLIED WARRANTIES IS LIMITED TO THE PERIOD(S) FROM THE DATE OF
PURCHASE SET FORTH BELOW. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
The warranties given herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy
available to the purchaser and only for the time periods set forth herein. No other representations or promises made by anyone are
permitted. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all
liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims,
whether based on contract, negligence, strict liability or otherwise. Sharp does not warrant nor shall Sharp be liable, or in any way
responsible, for Products which have been subject to abuse (including, but not limited to, improper voltage), accident, misuse, negligence,
lack of reasonable care, alteration, modification, tampering, misuse, improper operation or maintenance or any damages or defects in the
Product which were caused by repairs or attempted repairs performed by anyone other than a Sharp authorized servicer. Nor shall Sharp
be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow limits on
warranties or on remedies for breach in certain transactions; in such states, the limits herein may not apply.
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND PUERTO RICO.
Model Specific Section
Your Product Model Number & Description:
LC-90LE745U LCD Color Television
(Be sure to have this information available when you need service for your
Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
Additional Exclusions from
Warranty Coverage (if any):
In order for the Product to be serviced, the Product must be readily available
to the servicer, free and clear of any complex or non-standard installation,
mounting or other encumbrance which would unreasonably interfere with
servicing the Product. The Servicer will remount the Product after service,
provided that such remounting is not into a complex or non-standard installation. Any additional labor and materials required to remove and/or reinstall a
Product above and beyond the foregoing are not covered by this warranty,
may result in additional charges and are the responsibility of the consumer.
Image Retention resulting from a fixed image being displayed for long
periods of time is not covered by this Limited Warranty (see Operation
Manual on how to prevent this).
Where to Obtain Service:
From a Sharp Authorized Servicer located in the United States. To find the
location of the nearest Sharp Authorized Servicer, please call Sharp toll free
at 1-800-BE-SHARP.
What to do to Obtain Service:
Contact your Sharp Authorized Servicer to obtain in home service for this
product. The Servicer will come to your location and if necessary remove the
unit for repair at the Servicer’s facility and return the set to you once
completed. Be sure to have Proof of Purchase available.
TO OBTAIN PRODUCT INFORMATION OR PURCHASE ACCESSORIES AND EXTENDED WARRANTIES, CALL 1-800-BE-SHARP
OR VISIT www.sharpusa.com
93
LC-90LE745U_E.indb 93
2012/04/06 16:50:05
94
LC-90LE745U_E.indb 94
2012/04/06 16:50:05
Dimensional Drawings
Unit: inch (mm)
Unité: pouce (mm)
Unidad: pulgada (mm)
2 11/16 (68)*2
3 45/64 (94)
7
80 /8 (2054)
4 37/64 (116)
6 25/32
(172)
25 9/16 (649)
44 9/64 (1121.04)*1
47 11/16 (1211)
1 17/64
(32)
48 61/64 (1243)
78 15/32 (1992.96)*1
29 1/32 (737)
17 3/32 (434)
5
3
15 /16 (389)
15 /4 (400)
7 7/8 (200)
23 5/8 (600)
18 5/32 (461)
*1
*2
LC-90LE745U_E_Cover.indd 2
Active area/Área activa/Zone active
Thinnest part/Parte más delgada/Partie la plus mince
2012/03/27 19:42:33
FRANÇAIS
ENGLISH
LC-90LE745U
LC-90LE745U
OPERATION MANUAL
SHARP ELECTRONICS CORPORATION
ESPAÑOL
LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR ACL
TELEVISOR CON PANTALLA
DE CRISTAL LÍQUIDO
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE OPERACIÓN
MODE D'EMPLOI
Sharp Plaza, Mahwah, New Jersey 07495-1163
SHARP CORPORATION
MANUAL DE OPERACIÓN
Printed in Mexico
Imprimé au Mexique
Impreso en México
TINS-F501WJZZ
12P05-MX-NM
IMPORTANT : Please read this operation manual before starting operating the equipment.
IMPORTANT : Veuillez lire ce mode d'emploi avant de commencer à utiliser l'appareil.
IMPORTANTE : Lea este manual de operación antes de comenzar a operar el equipo.
LC-90LE745U_E_Cover.indd 1
2012/03/27 19:42:33