EK Water Blocks EK-FC7970 - Acetal + Nickel CSQ null

Add to my manuals
2 Pages

advertisement

EK Water Blocks EK-FC7970 - Acetal + Nickel CSQ null | Manualzz

Installation and mounting manual for EK-FC7970 CSQ water block

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com

for updates. Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual before through before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK High Flow and EK-PSC type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of corrosion inhibiting coolants is always recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION. Sample picture of AMD Radeon HD 7970 graphics card (PCB 109-C38637-00) STEP 2: PREPARING YOUR GRAPHIC CARD.

1. REMOVING STOCK COOLER: Remove encircled screw on the bracket (required only on certain models):

STEP 2 cont.: PREPARING YOUR GRAPHIC CARD

1 cont.. REMOVING STOCK COOLER.

Remove all encircled screws. All heat sink assembly screws should be removed. There are 16 screws on the back of the graphic card.

2. CLEANING THE PCB. Carefully detach the original stock cooler after removing

all screws securing it to the board. Wipe off the remains (by using non–abrasive cloth or qtip , as shown on sample photo) of the original thermal compound until the components and circuit board are completely clean. EKWB recommends the use of denatured alcohol for removing TIM leftovers.

3. APPLYING THERMAL COMPOUND. Apply thermal compound: lightly coat AMD GPU chip with for example

Arctic Cooling MX-2 ™ or MX-4 ™ thermal grease. EKWB recommends to apply thermal grease in cross form for best performance (see sample picture).

4. CUTTING THERMAL PADS.

Your block comes with thermal pads, some of which are already pre-cut. Others have to be cut to smaller chunks in order to cover all the VRM components such as MOSFETs and drivers. PLEASE REMOVE

THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION.

Replacement thermal pads: 1x Thermal Pad B – 0.5mm (75x50mm), Thermal Pad A – 1mm (100x16mm).

3: Thickness 1mm (for I/O VRM):

1: Thickness 0.5mm

(for memory IC):

1 1 1 1 1 3

2: Thickness 0.5mm

(for VRM Driver & MOSFET IC):

1 1 1 1 1

2

2

1 1

STEP 3: INSTALLING WATER BLOCK

1. PLACING THERMAL PADS ON PCB.

Place thermal pads on chips so that numbers on chips match size of thermal pads. EKWB made sure users have more than enough pads to cover all surfaces that need to be covered to make block fully functional). EKWB recommends using small drops of electrically non-conductive (for example: Arctic Cooling MX-2 ™, MX-4 ™ or GELID GC-Extreme™) thermal grease on each phase regulator (that is being covered with thermal pad) in order to even further improve the thermal performance of the EK-FC7970 CSQ series water block.

1 1 1 1

3

1

1

2

1

1

1

1

2

1

1

All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use. Released on 21 st

of June, 2012. Revision 1.0

2. PLACING BLOCK TO GRAPHIC CARD . Carefully position the water block with preinstalled 2.5mm standoffs on to the graphics card. During this process please make sure you align mounting holes on PCB with holes on the water block. Also pay attention not to use too much force by pressing block down to PCB. Chip dies are prone to cracking.

3. ATTACHING BLOCK TO GRAPHIC CARD . By using Philips screwdriver screw in enclosed M3x4 DIN7985 screws. EKWB recommends start screwing the screws around the GPU core and continue outwards. Always use a PVC washer under each and every screw!

Use 11 screws M3x4

Use 11 enclosed PVC washers underneath each screw!

STEP 4: CHECKING FOR CONTACTS

Temporarily remove the water block to check for uniform surface contact between the block and the components, pay special attention to the VRM section of the graphics card.

Check whether the water block makes contact with the VRM. Then repeat sub-steps in previous section to re-attach the block. In case you fail to obtain good contact,

please check again your thermal pad thickness or contact our support service.

STEP 7: INSERTING CARD IN YOUR PC CASE STEP 5: FITTING POSITIONING

Carefully lift your graphics card with installed block and insert it in your PC’s motherboard PCI-express expansion slot. Please bear in mind that your graphics card is probably heavier than when it was equipped with original heat sink fan assembly. One needs to be very careful when handling the graphics card. Avoid all un-needed manipulation of the VGA/water block assembly that might damage your card or water block during final installation.

Screw in the fittings in the G1/4 threaded openings on plastic top of the water block.

EKWB recommends using EK-PSC fittings with the EK-FC7970 CSQ series water blocks.

To ensure that the tubes are securely attached to the barb/fittings, please use hose clamps or an appropriate substitute. You can use any opening as an inlet/outlet port.

Tubing

EK-PSC Fitting

Water block top

REQUIRED TOOLS AND MOUNTING SCREWS:

INSTALLING EK-FC LINK:

Alternatively you can install the enclosed EK-FC Link which allows installation of both

EK-FC Bridge system as well as the use of G1/4 threaded fittings.

Please remove the middle M4x8 DIN7984 screw, install the EK-FC Link together with

OR 14x1.5mm gaskets and secure it with enclosed M4x25 DIN7985 screw. Use enclosed 2.5mm Allen (hex) key!

Once installed you can install two (preferably angled) G1/4 threaded fittings or any EK-

FC Bridge CSQ series interconnect ( serial or parallel )

M4x25 DIN7984

EK-FC Link

scissors philips screwdriver

thermal grease OR 14x1.5mm

All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use. Released on 21 st

of June, 2012. Revision 1.0

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement