Philips Original radio OR7200

Register your product and get support at
OR7200
User manual
OR7200
User Manual
2 sec.
2 sec.
DAB+
Congratulations on your purchase, and welcome to Philips! To fully
benefit from the support that Philips offers, register your product at
www.philips.com/welcome.
1Safety
Read and understand all instructions before you use this product. If
damage is caused by failure to follow the instructions, the warranty
does not apply.
Risk of electric shock or fire!
•
•
•
•
•
•
Never expose the product and accessories to rain or water. Never
place liquid containers, such as vases, near the product. If liquids are
spilt on or into the product, disconnect it from the power outlet
immediately. Contact Philips Consumer Care to have the product
checked before use.
Never place the product and accessories near naked flames or other
heat sources, including direct sunlight.
Never insert objects into the ventilation slots or other openings on
the product.
Where the mains plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain readily
operable.
Disconnect the product from the power outlet before lightning
storms.
When you disconnect the power cord, always pull the plug, never
the cable.
Risk of short circuit or fire!
•
Before you connect the product to the power outlet, make sure
that the power voltage matches the value printed on the back of
the product. Never connect the product to the power outlet if the
voltage is different.
•
•
Never expose the product to rain, water, sunshine, or excessive heat.
Avoid force coming onto power plugs. Loose power plugs can cause
arcing or fire.
Risk of injury or damage to the product!
•
•
•
•
This product shall not be exposed to dripping or splashing!
Do not place any sources of danger on this product (e.g. liquid filled
objects, lighted candles).
Never place the product or any objects on power cords or on other
electrical equipment.
If the product is transported in temperatures below 5°C, unpack the
product and wait until its temperature matches room temperature
before connecting it to the power outlet.
Risk of overheating!
•
•
Never install this product in a confined space. Always leave a space
of at least four inches around the product for ventilation.
Make sure that curtains or other objects never cover the ventilation
slots on the product.
Note
•• The type plate is located on the back of the product.
Important notes for users in the U.K.
Mains fuse
This information applies only to products with a UK mains plug.
This product is fitted with an approved non-molded plug. If you
replace the fuse, use one with:
•
the ratings shown on the plug,
•
•
a BS 1362 approval, and
the ASTA approval mark.
Contact your dealer if you are not sure about what type of fuse to use.
Caution: To conform with the EMC directive (2004/108/EC), do not
detach the plug from the power cord.
How to connect a plug
The wires in the power cord are colored as follows: blue = neutral
(N), brown = live (L).
If the colors do not correspond with the colors on your plug, identify
the terminals in your plug as follows:
1
Connect the blue wire to the terminal marked N or colored
black.
2
Connect the brown wire to the terminal marked L or colored
red.
3
Do not connect either wire to the earth terminal in the plug,
marked E (or e) or colored green (or green and yellow).
Before you replace the plug cover, make sure that the cord grip is
clamped over the sheath of the cable and not just over the two wires
in the cable.
2
What’s in the box (Fig. 1)
3
Connect power (Fig. 2-1)
4
Turn on (Fig. 2-2)
Press the
knob or turn the SOURCE knob.
»» The product switches to the last selected source.
•
To switch the product to standby mode, press the
knob again.
5
1
2
Set the clock (Fig. 3)
In standby mode, press and hold the
»»
knob for 2 seconds.
(12-hour time format) or
(24-hour time format) blinks.
Turn the
knob to select a time format, and then press the
knob to confirm.
»» Hour digits blink.
3
Turn the
knob to set the hour, and then press the
knob to confirm.
»» Minute digits blink.
4
5
6
1
2
Turn the
knob to set the minute.
Press the
knob to confirm.
Listen to FM radio stations
Turn the SOURCE knob to switch the product to FM mode.
Search for radio stations automatically or manually.
Note
•• For optimal reception, fully extend the antenna and adjust its
position.
•• You can store a maximum of 30 FM radio stations.
Search for a radio station automatically
Press SCAN to activate the auto search.
»» After a strong station is detected, the search stops and the
radio station is broadcast.
Search for a radio station manually
Turn the
displayed.
knob until the frequency of target radio station is
Store radio stations automatically (Fig. 4)
Press and hold SCAN to activate the auto search.
•
»» After the search is complete, the first stored radio station is
broadcast.
To tune to a stored radio station, turn the PRESET knob until its
frequency is displayed.
Program radio stations manually
1
2
3
4
5
•
Tune to a radio station.
Press the PROGRAM button to activate the programming.
Turn the
knob to select a preset sequence number.
Press the
knob to confirm.
»» The radio station is stored with the selected sequence number.
Repeat steps 1-4 to program more radio stations.
To tune to a preset radio station, turn the PRESET knob until its
frequency is displayed.
Note
•• If you store a radio station with the sequence number of another one, the earlier one
is overwritten.
Display RDS information
Radio Data System (RDS) is a service that allows FM stations to
transmit additional information. When you tune to an FM radio station
that transmits RDS signals, the station name is displayed.
1
2
Tune to an RDS station.
Press INFO repeatedly to scroll through the following
information (if available):
• Radio text
•
•
•
•
•
Program type such as [NEWS] (news), [SPORT] (sport),
[POP M] (pop music)...
Program service
Mono/Stereo
Time
Date
RDS program types
Program
type
Description
Program
type
Description
NEWS
News services
FINANCE
Finance
AFFAIRS
Politics and current
affairs
CHILDREN
Children's
programs
INFO
Special information
programs
SOCIAL
Social affairs
SPORT
Sports
RELIGION
Religion
EDUCATE
Education and
advanced training
PHONE IN
Phone in
DRAMA
Radio plays and
literature
TRAVEL
Travel
CULTURE
Culture, religion and
society
LEISURE
leisure
SCIENCE
Science
JAZZ
Jazz Music
VARIED
Entertainment
programs
COUNTRY
Country Music
POP M
Pop music
NATION M
National Music
ROCK M
Rock music
OLDIES
Oldies Music
MOR M
Light music
FOLK M
LIGHT M
Light classical music
DOCUMENT Documentary
Folk Music
CLASSICS
Classical music
TEST
Alarm Test
OTHER M
Special music
programs
ALARM
Alarm
WEATHER Weather
Adjust FM settings
1
2
In FM mode, press MENU to access FM menus.
Turn the
knob to toggle through the menus.
Scan setting
1
2
Press the
3
Press the
knob to access sub-menus.
Turn the
knob to select an option.
• <Strong stations>: Search for strong stations only.
• <All stations>: Search for all stations no matter whether
the signal strength of a station is strong or weak.
knob to confirm the option.
Audio setting
1
2
Press the
3
Press the
knob to access sub-menus.
Turn the
knob to select an option.
• <Stereo allowed>: Allow stereo output even if the station
transmits weak stereo audio signals.
• <Forced mono>: Convert stereo signals to monophonic
output even if the station transmits strong stereo audio
signals.
knob to confirm the option.
System menus
1
2
•
Press the
knob to access system menus.
Turn the
knob to select a sub-menu.
For details, refer to the section ‘Use system menus‘.
7
Listen to DAB radio stations
Note
•• For optimal reception, fully extend the antenna and adjust its
position.
•• You can program a maximum of 30 DAB radio stations.
•• Check with local retailer or go to www.WorldDAB.org for
applicable DAB radio frequencies in your area.
For the first time use (Fig. 5)
1
2
3
Turn the SOURCE knob to switch the product to DAB mode.
Turn the
knob until the <Full scan> menu is displayed.
Press the
knob to activate the automatic search.
»» This product automatically stores radio stations with sufficient
signal strength.
»» After the search is complete, the first stored radio station is
broadcast automatically.
4
Turn the
knob to select a station, and then press the
knob to start listening.
Tip
•• You can re-scan to update the list of stored stations (see "Use DAB
menus" > "Re-scan for stations").
•• You can tune to a station manually (see "Use DAB menus" > "Tune
to a station manually").
About special symbols
Some symbol may be displayed before the name of a station.
•
•
•
•
H: The station is one of your 10 favorite stations.
?: The station is unavailable or inactive.
: The station is a primary station with secondary service.
: The station is a secondary station.
Program radio stations
1
2
3
4
5
•
Tune to a DAB radio station.
Press PROGRAM to activate the programming.
Turn the
knob to select a preset sequence number.
Press the
knob to confirm.
»» The radio station is stored with the selected sequence number.
Repeat steps 1-4 to program more radio stations.
To tune to a preset radio station, turn the PRESET knob until its
frequency is displayed.
Note
•• If you store a radio station with the sequence number of another one, the earlier one
is overwritten.
Display DAB information
On the display of DAB broadcasting, the first line shows station name,
and the second line shows the service information for the current
station.
Press INFO repeatedly to cycle through the following information
(if available).
•
•
•
•
•
•
•
•
•
Dynamic label segment (DLS)
Signal strength
Program type (PTY)
Ensemble name
Frequency
Signal error rate
Bitrate codec
Time
Date
Use DAB menus
1
2
In DAB mode, press MENU to access the DAB menus.
Turn the
knob to toggle through the menus.
Tune to a stored station
1
Press the
knob to access the list of stored stations.
• If no DAB station is stored, the product starts automatic
search.
2
3
Turn the
knob to select a station.
Press the
knob to start listening.
Re-scan for stations
Full scan is used to perform a wide range search for DAB radio
stations.
Press the
knob to start scanning for available DAB stations.
»» After the scanning is complete, the first detected station is
broadcast.
Tune to a station manually
With this feature, you can tune to a specific channel/frequency
manually. In addition to antenna orientation for better radio reception,
the optimal reception can also be obtained with this feature.
1
2
Press the
knob to access the station list.
Turn the
knob to select a station from 5A to 13F.
3
Press the
knob to confirm the option.
DRC (Dynamic Range Control)
DRC adds or removes a degree of compensation for the differences
in the dynamic range between radio stations.
1
Press the
knob to access the sub-menus.
2
3
Turn the
knob to select an option.
• <DRC off>: No compensation applied. (The asterisk
indicates the current setting.)
• <DRC low>: Medium compensation applied.
• <DRC high>: Maximum compensation applied.
Press the
knob to confirm the option.
Remove invalid stations
This option lists active stations and removes any stations that are in
the list but have no service in your area. In front of the station name
of an invalid station, a question mark (?) is displayed.
1
2
Press the
3
Press the
knob to access the sub-menus.
Turn the
knob to select an option.
• <No>: Return to the previous menu.
• <Yes>: Remove invalid stations from the station list.
knob to confirm the option.
System menus
1
Press the
knob to access system menus.
2
•
Turn the
knob to select a sub-menu.
For details, refer to the section ‘Use system menus‘.
8
Use system menus
Use the system menus to
•
•
•
check the version of current software of this product,
upgrade the software, and
reset the product to factory default status.
Check the current software version
Press the
knob to display the version of current software.
Reset the product
1
2
Press the
3
Press the
knob to display the options.
Turn the
knob to select an option.
• <No>: Return to the previous menu.
• <Yes>: Reset the product to factory default status.
knob to confirm the option.
Upgrade the software
1
2
Go to www.philips.com/support.
Search for support information about your product with
“OR7200/10“ as the keyword.
»» When an upgrade packet is available, the link of “Firmware
Upgrade Readme File“ is accessible. The exact wording of this
link name may vary in different languages.
3
4
5
9
Click the link of “Firmware Upgrade Readme File“.
Read and understand the instructions on software upgrade.
Follow the instructions to complete the upgrade.
Listen to an external device
(Fig. 6)
You can also listen to an external audio device, for example, MP3
player, through this product.
1
Turn the SOURCE knob to switch the product to MP3-Link
mode.
2
Connect the MP3 link cable to
• the MP3-LINK socket on the back panel of this product,
and
• the headphone jack on the external device.
3
Play the external device (refer to its user manual).
10
Adjust the volume
Turn the
knob.
11Troubleshooting
Warning
•• Never remove the casing of this product.
To keep the warranty valid, never try to repair the product yourself.
If you encounter problems when using this product, check the
following points before requesting service. If the problem remains
unsolved, go to the Philips Web page (www.philips.com/support).
When you contact Philips, make sure that the product is nearby and
the model number and serial number are available.
No power
••
••
Make sure that the AC power cord is properly connected.
Make sure that there is power at the AC power outlet.
No sound
••
Adjust the volume.
••
In MP3-Link mode, make sure that the external audio device is not
muted.
No response from the product
• Make sure that the power is available.
• Turn off the product, and then turn it on again.
Poor radio reception
••
Due to the interference from other electrics or building obstacles,
the signals become weak. Move the product to a place free of
interference.
••
Make sure that the antenna is fully extended. Adjust the position of
the antenna.
Clock setting is erased.
•
•
Power has been interrupted, or the AC power cord has been
disconnected.
Set the clock again.
12
Product information
Note
•• Product information is subject to change without prior notice.
Amplifier
Frequency Response
60 Hz - 16 kHz, ±3 dB
Signal to Noise Ratio
> 65 dBA
Aux Input
0.5 V RMS 20 kohm
Tuner
Tuning Range
FM: 87.50 - 108.00 MHz;
DAB: 174.928-239.200 MHz
Tuning grid
50 kHz
DAB sensitivity (EN50248)
< -95 dbm
Total Harmonic Distortion
< 2%
Signal to Noise Ratio
> 50 dBA
Number of preset radio stations
30 (FM), 30 (DAB)
Speakers
Speaker Impedance
4 ohm
Speaker Driver
2 X 3" full range
Sensitivity
>82 dB/m/W
General information
AC Power Rating
220-240 V~, 50 Hz
Operation Power Consumption
10 W
Dimensions (Main Unit)
325 x 175 x 167 mm
Weight (Main Unit)
3.5 kg
13Notice
Any changes or modifications made to this device that are not
expressly approved by Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
Compliance
This product complies with the radio interference
requirements of the European Community.
This is CLASS II apparatus with double insulation,
and no protective earth provided.
Care of the environment
Your product is designed and manufactured with high
quality materials and components, which can be recycled
and reused.
When this crossed-out wheeled bin symbol is attached
to a product it means that the product is covered by the
European Directive 2002/96/EC. Please inform yourself
about the local separate collection system for electrical
and electronic products.
Please act according to your local rules and do not dispose of your
old products with your normal household waste.
Correct disposal of your old product helps to prevent potential
negative consequences for the environment and human health.
Environmental information
All unnecessary packaging has been omitted. We have tried to make
the packaging easy to separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags, protective foam
sheet.)
Your system consists of materials which can be recycled and reused
if disassembled by a specialized company. Please observe the local
regulations regarding the disposal of packaging materials, exhausted
batteries and old equipment.
Copyright
2012 © Koninklijke Philips Electronics N.V.
Specifications are subject to change without notice. Trademarks are
the property of Koninklijke Philips Electronics N.V or their respective
owners. Philips reserves the right to change products at any time
without being obliged to adjust earlier supplies accordingly.
All registered and unregistered trademarks are
property of their respective owners.
© 2012 Koninklijke Philips Electronics N.V.
All rights reserved.
OR7200_10_UM_V1.0