Bretford EC2741-GM Manual

Add to my manuals
3 Pages

advertisement

Bretford EC2741-GM Manual | Manualzz

EC2741

COMPUTER WORK STATION /

PROJECTOR TABLE

Assembly Instructions

1

2

2

1

1

1

1

Parts List

Qty.

Part No.

1 022-2014

022-2013

022-1694

010-2336

010-3273

010-3058

015-0002

015-0003

Description

Top Section Assembly

(with Modesty Panel/Wire Bin)

Leg Assembly with CPU Shelf

Leg Assembly

Cross Brace

CPU Side Bracket - Stationary

CPU Side Bracket - Adjustable

4" Swivel Caster-Rear

4" Swivel Caster with Brake-Front

Tools Required

Phillips Screw Driver

1/2" Open End Wrench

Hardware List

2

2

2

4

8

2

2

8

Qty.

Ref.

Part No.

2 AA

BB

CC

DD

EE

FF

GG

HH

I I

030-0307

030-0421

030-0253

030-0120

030-0272

030-0325

030-0256

031-1822

031-1823

Description

5/16-18 x 5/8" Hex Head Bolt

5/16-18 Hex Nylock Nut

1/4-20 x 3/4" Combo Head Screw

1/4-20 Square Nut

1/4-20 x 1/2" Carriage Bolt

1/4-20 x 1/2" Combo Truss Screw

1/4-20 Flange Nut

Velcro - Hook

Velcro - Loop

Leg Assembly w/ CPU Shelf DD

Leg Assembly

CC

Top Section Assembly

Step 1

With the top section assembly placed face down on a carpeted surface (or cardboard), position the modesty panel toward the rear. Then determine whether the leg assembly with the cpu shelf will be located on the left or right side of your table (when turned over upright). The above view shows a right hand shelf location. Slide one leg assembly into the leg extensions from the top section assembly as shown. Align the mounting holes until the desired height is achieved. Note: the table height is adjustable from 27" to 41" when casters are installed.

Once the height is set, install 1/4-20 screws (CC) and 1/4-20 nuts (DD). Install the second leg the same as the first leg. Tighten securely.

Open end facing up

BB

AA

Step 2

Attach the cross brace to the two leg assemblies using 5/16-18 screws (AA) and 5/16-18 nylock nut (BB). Two

1/2" open end wrenches recommended to tighten the 5/16-18 hardware.

FRONT

Step 3

Install two casters without the brake at the rear of the table by inserting the stem of the caster into the sockets of leg assembly base. Repeat the same for the two casters with the brake at the front of the table.

The table is ready to be turned upright.

FF

Stationary

CPU

Bracket

EE

Adjustable CPU

Bracket

GG

Step 4

When mounting the cpu brackets, the first set of mounting holes to the front edge of the cpu shelf are utilized whether the side shelf is mounted on the left or right side of the table. Attach stationary cpu side bracket with flange facing the exterior of the table and secure with 1/4-20 screws (FF) and 1/4-20 flanged nuts (GG) as shown. Attach adjustable cpu side bracket with flange facing the exterior of the table and secure with 1/4-20 carriage screws (EE) and 1/4-20 flanged nuts (GG) as shown.

HH

I I I I

HH

Step 5

Attach two pieces of velcro-hook (HH) and loop (I I) to each cpu brackets interior surface as shown. This will hold your cpu in place by keeping it from moving forward or backward on the shelf.

Bretford

11000 Seymour Avenue

Franklin Park, IL 60131

TEL: 847.678.2545

800.521.9614

FAX: 847.678.0852

800.343.1779

www.bretford.com

Bretford Ltd.

Technology House

7 Lake End Court, Taplow

Bucks SL6 0JQ England

TEL: 01628 603558

FAX: 01628 604923

Part #031-3359

Rev. 06.03.05 CH

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement