BDCS36G
A
B
C
D
E
F
2
(Original instructions)
Intended use
Your Black & Decker screwdriver has been
designed for screwdriving applications. This
tool is intended for consumer use only.
Safety instructions
General power tool safety warnings
@
Warning! Read all safety
warnings and all instructions.
Failure to follow the warnings
and instructions listed below
may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for
future reference. The term "power tool" in
all of the warnings listed below refers to your
mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b. Do not operate power tools in
explosive atmospheres, such as in the
presence of flammable liquids, gases
or dust. Power tools create sparks which
may ignite the dust or fumes.
c. Keep children and bystanders away
while operating a power tool.
Distractions can cause you to lose control.
ENGLISH
2. Electrical safety
a. Power tool plugs must match the
outlet. Never modify the plug in any
way. Do not use any adapter plugs with
earthed (grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
b. Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric shock.
d. Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e. When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3
ENGLISH
(Original instructions)
3. Personal safety
a. Stay alert, watch what you are doing
and use common sense when
operating a power tool. Do not use a
power tool while you are tired or under
the influence of drugs, alcohol or
medication. A moment of inattention
while operating power tools may result in
serious personal injury.
b. Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing
protection used for appropriate conditions
will reduce personal injuries.
c. Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools
that have the switch on invites accidents.
d. Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in
personal injury.
e. Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in
unexpected situations.
4
f. Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g. If devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use of
dust collection can reduce dust-related
hazards.
4. Power tool use and care
a. Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b. Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the
switch is dangerous and must be repaired.
c. Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive
safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
(Original instructions)
e. Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power
tools operation. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to bind
and are easier to control.
g. Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger
specified by the manufacturer. A
charger that is suitable for one type of
battery pack may create a risk of fire when
used with another battery pack.
b. Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
ENGLISH
c. When battery pack is not in use, keep it
away from other metal objects, like
paper clips, coins, keys, nails, screws,
or other small metal objects, that can
make a connection from one terminal
to another. Shorting the battery terminals
together may cause burns or a fire.
d. Under abusive conditions, liquid may
be ejected from the battery; avoid
contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid
ejected from the battery may cause
irritation or burns.
6. Service
a. Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
Additional power tool safety warnings
@
Warning! Additional safety
warnings for screwdrivers and
impact wrenches
Wear ear protectors with impact drills.
Exposure to noise can cause hearing loss.
u Use auxiliary handles if supplied with
the tool. Loss of control can cause
personal injury.
u
5
ENGLISH
(Original instructions)
Hold power tool by insulated gripping
surfaces when performing an operation
where the fastener may contact hidden
wiring. Fasteners contacting a "live" wire
may make exposed metal parts of the
power tool "live" and could give the operator an electric shock.
u Use clamps or another practical way
to secure and support the workpiece
to a stable platform. Holding the work
by hand or against your body leaves it
unstable and may lead to loss of control.
u This tool is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure
that they do not play with the appliance.
u
Safety of others
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
u Children should be supervised to ensure
that they do not play with the appliance.
u
6
Residual risks.
Additional residual risks may arise when using
the tool which may not be included in the
enclosed safety warnings. These risks can
arise from misuse, prolonged use etc.
Even with the application of the relevant
safety regulations and the implementation of
safety devices, certain residual risks can not
be avoided. These include:
u Injuries caused by touching any rotating/
moving parts.
u Injuries caused when changing any parts,
blades or accessories.
u Injuries caused by prolonged use of a tool.
When using any tool for prolonged periods
ensure you take regular breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust
developed when using your tool (example:- working with wood, especially oak,
beech and MDF.)
Vibration
The declared vibration emission values stated
in the technical data and the declaration of
conformity have been measured in accordance with a standard test method provided
by EN 60745 and may be used for comparing
one tool with another. The declared vibration
emission value may also be used in a preliminary assessment of exposure.
(Original instructions)
Warning! The vibration emission value during
actual use of the power tool can differ from
the declared value depending on the ways in
which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to
determine safety measures required by
2002/44/EC to protect persons regularly using
power tools in employment, an estimation of
vibration exposure should consider, the actual
conditions of use and the way the tool is used,
including taking account of all parts of the
operating cycle such as the times when the
tool is switched off and when it is running idle
in addition to the trigger time.
Labels on tool
The following symbols are shown on the tool:
:
Warning! To reduce the risk of
injury, the user must read the
instruction manual.
Additional safety instructions for batteries and chargers
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the
temperature may exceed 40 °C.
u Charge only at ambient temperatures
between 10 °C and 40 °C.
ENGLISH
Charge only using the charger provided
with the tool.
u When disposing of batteries, follow the
instructions given in the section "Protecting the environment".
u
p
Do not attempt to charge damaged batteries.
Chargers
u Use your Black & Decker charger only to
charge the battery in the tool with which it
was supplied. Other batteries could burst,
causing personal injury and damage.
u Never attempt to charge non-rechargeable batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
$
The charger is intended for
indoor use only.
Read the instruction manual
before use.
7
ENGLISH
(Original instructions)
Electrical safety
#
u
Your charger is double insulated; therefore no earth wire
is required. Always check that
the mains voltage corresponds
to the voltage on the rating
plate. Never attempt to replace
the charger unit with a regular
mains plug.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised Black & Decker Service Centre
in order to avoid a hazard.
Features
This tool includes some or all of the following
features.
1. Motion control activator
2. Bit holder
3. Charger connector
4. LED work light
Fig. A
5. Charger
8
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing a screwdriver bit
or socket (fig. B)
Warning! Make certain the tool is locked to
prevent switch actuation before installing or
removing accessories.
u To fit a screwdriver bit push it into the bit
holder (2) until it locates.
u To remove a screwdriver bit, pull it straight
from the bit holder.
Note! To remove the bit/socket repeat the
above steps.
Use
Warning! Let the tool work at its own pace.
Do not overload.
Charging the battery (fig. C)
The battery needs to be charged before first
use and whenever it fails to produce sufficient
power on jobs that were easily done before.
The battery may become warm while charging; this is normal and does not indicate a
problem.
u To charge the battery, insert the charger
plug (5) into the charger connector (3).
u Plug in the charger.
u Leave the tool connected to the charger
for 16 hours.
(Original instructions)
The charger may hum and become warm
while charging; this is normal and does not
indicate a problem.
Warning! Do not charge the battery at ambient temperatures below 10 °C or above 40
°C. Recommended charging temperature:
approx. 24 °C.
Low battery indicator
When the battery charge becomes low the
LED work light will begin to flash.
u The LED Flash will last 5 seconds during
Low voltage --- --- --- at this pattern..
Warning! Do not continue using the product
with its batteries in a depleted condition.
Recharge discharged batteries promptly..
High temperature indicator
When the circuit operating temperature
becomes too high the LED work light will
begin to flash.
u The LED Flash will last 5 seconds during
circuit high temperature ---- -- ---- -- ---- at
this pattern. Allow the unit to cool down
to an optimal operating temperature of
approximately 24°C.
Setting the initial starting point (fig. D)
Grasp the screwdriver as shown in figure
D.
u Press and hold in the motion control
activator (1) on the back of the tool with
the palm of your hand.
u
ENGLISH
When the LED work light (4) illuminates
the tool is ready for use.
u To reset initial starting point first release
the motion control activator (1). Move tool
to new position, then press and hold in the
motion control activator (1) on the back of
the tool with the palm of your hand..
u
Operating in the forward direction
(fig. E)
Set the initial starting point.
Rotate the tool clockwise and the screwdriver will activate in the forward direction.
Note: The speed of the tool is determined by
the amount of rotation. .
Small rotation = slower speed.
Large rotation = Higher speed.
u
u
Operating in the reverse direction
(fig. F)
Set the initial starting point.
Rotate the tool anti-clockwise and the
screwdriver will activate in the reverse
direction.
Note: The speed of the tool is determined by
the amount of rotation. .
Small rotation = slower speed.
Large rotation = Higher speed.
u
u
LED work light
The LED work light (4) is activated automatically when the motion control activator (1) is
depressed.
9
ENGLISH
(Original instructions)
Hints for optimum use
Screwdriving
u Always use the correct type and size of
screwdriver bit.
u If screws are difficult to tighten, try applying a small amount of washing liquid or
soap as a lubricant.
u Always hold the tool and screwdriver bit in
a straight line with the screw.
Maintenance
Your Black & Decker tool has been designed
to operate over a long period of time with
a minimum of maintenance. Continuous
satisfactory operation depends upon proper
tool care and regular cleaning.
Your charger does not require any maintenance apart from regular cleaning.
Warning! Before performing any maintenance
on the tool, remove the battery from the tool.
Unplug the charger before cleaning it.
u Regularly clean the ventilation slots in
your tool and charger using a soft brush or
dry cloth.
u Regularly clean the motor housing using
a damp cloth. Do not use any abrasive or
solvent-based cleaner.
u Regularly open the chuck and tap it to
remove any dust from the interior.
10
Protecting the environment
Z
Separate collection. This product
must not be disposed of with
normal household waste.
Should you find one day that your Black &
Decker product needs replacement, or if it
is of no further use to you, do not dispose of
it with household waste. Make this product
available for separate collection.
z
Separate collection of used
products and packaging allows
materials to be recycled and used
again.
Re-use of recycled materials helps
prevent environmental pollution
and reduces the demand for raw
materials.
Local regulations may provide for separate
collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
Black & Decker provides a facility for the
collection and recycling of Black & Decker
products once they have reached the end of
their working life. To take advantage of this
service please return your product to any
authorised repair agent who will collect them
on our behalf.
(Original instructions)
You can check the location of your nearest
authorised repair agent by contacting your
local Black & Decker office at the address
indicated in this manual. Alternatively, a list
of authorised Black & Decker repair agents
and full details of our after-sales service and
contacts are available on the Internet at:
www.2helpU.com
Batteries
Z
u
Run the battery down completely,
then remove it from the tool.
NiCd, NiMH and Li-Ion batteries are
recyclable. Take them to any authorised
repair agent or a local recycling station.
ENGLISH
Technical data
BDCS36G
(H1)
Voltage
VDC
3.6
No-load speed
Min-1
180
Max. torque
Nm
3
(PTI Rating)
Li-Ion
Battery type
Battery capacity
Ah
1.1
Weight
kg
0.3
Charger
905450** typ. 1
Input Voltage
VAC
230
Output Voltage
VDC
9
Current
mA
100
Approx. charge time
min
12-15
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 62.8 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 73.8 dB(A), uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according
to EN 60745:
Screwdriving without impact (ah, S) < 2.5 m/s2, uncertainty
(K) 1.5 m/s2
11
ENGLISH
(Original instructions)
EC declaration of conformity
%
MACHINERY DIRECTIVE
BDCS36G
Black & Decker declares that these products
described under "technical data" are in
compliance with:
2006/42/EC, EN 60745-1, EN 60745-2-2
These products also comply with Directive
2004/108/EC and 2011/65/EU. For more
information, please contact Black & Decker at
the following address or refer to the back of
the manual.
The undersigned is responsible for compilation of the technical file and makes this
_
declaration on behalf of Black & Decker.
12
Kevin Hewitt
Vice-President Global Engineering
Black & Decker Europe, 210 Bath Road,
Slough,
Berkshire, SL1 3YD
United Kingdom
09/03/2012
Guarantee
Black & Decker is confident of the quality of its
products and offers an outstanding guarantee.
This guarantee statement is in addition to and
in no way prejudices your statutory rights. The
guarantee is valid within the territories of the
Member States of the European Union and
the European Free Trade Area.
If a Black & Decker product becomes defective due to faulty materials, workmanship or
lack of conformity, within 24 months from the
date of purchase, Black & Decker guarantees
to replace defective parts, repair products
subjected to fair wear and tear or replace
such products to ensure minimum inconvenience to the customer unless:
u The product has been used for trade,
professional or hire purposes;
u The product has been subjected to
misuse or neglect;
u The product has sustained damage
through foreign objects, substances or
accidents;
u Repairs have been attempted by persons
other than authorised repair agents or
Black & Decker service staff.
(Original instructions)
ENGLISH
To claim on the guarantee, you will need to
submit proof of purchase to the seller or an
authorised repair agent. You can check the
location of your nearest authorised repair
agent by contacting your local Black & Decker
office at the address indicated in this manual.
Alternatively, a list of authorised Black &
Decker repair agents and full details of our
after-sales service and contacts are available
on the Internet at: www.2helpU.com
Please visit our website www.blackanddecker.co.uk to register your new Black &
Decker product and to be kept up to date
on new products and special offers. Further
information on the Black & Decker brand and
our range of products is available at www.
blackanddecker.co.uk
13
ENGLISH
Do not forget to register your product!
www.blackanddecker.co.uk/productregistration
Register your product online at www.blackanddecker.co.uk/productregistration or send your
name, surname and product code to Black & Decker in your country.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark, Victoria, 3138
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Auckland 1060
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
90585906 REV-0
Tel. 03-8720 5100
Fax 03-9727 5940
Tel. +64 9 259 1133
Fax +64 9 259 1122
Tel. 01753 511234
Fax 01753 551155
03/2012