LCD Display Monitor
MODEL
Features ............................................................................................................................................................................................... English-2
Important Information ............................................................................................................................................................................ English-3
Declaration ............................................................................................................................................................................................ English-5
Safety Precautions, Maintenance & Recommended Use ..................................................................................................................... English-6
Contents ............................................................................................................................................................................................... English-7
Parts Name and Functions .................................................................................................................................................................... English-8
Buttons, Switch, and Indicator............................................................................................................................................... English-8
Connectors and Terminals ..................................................................................................................................................... English-9
Wireless Remote Control ....................................................................................................................................................... English-10
How to Use the Wireless Remote Control ............................................................................................................................. English-11
Preparation for use ................................................................................................................................................................................ English-12
Flow of preparation ................................................................................................................................................................ English-12
[P-1] Preparation for installation ......................................................................................................................................................... English-13
Determine the installation location ......................................................................................................................................... English-13
Ventilation requirements for enclosure mounting .................................................................................................................. English-13
[P-2] Installing the monitor ................................................................................................................................................................. English-14
Using the wall mount or ceiling mount................................................................................................................................... English-14
Preventing the handles from touching the wall ...................................................................................................................... English-14
Installing in the portrait position ............................................................................................................................................. English-15
Attaching the corner protectors ............................................................................................................................................. English-15
Using the monitor without the bezel ...................................................................................................................................... English-16
[P-3] Installing the optional speakers ................................................................................................................................................. English-17
[P-4] Connection procedure ............................................................................................................................................................... English-18
Wiring diagram ....................................................................................................................................................................... English-18
Prevention of disconnection of HDMI cable .......................................................................................................................... English-19
Connecting with a computer (analog connection) ................................................................................................................. English-20
Connecting with a computer (digital connection) .................................................................................................................. English-21
Connecting a video device (component video/HDMI device) ................................................................................................ English-22
Connecting a video device (composite video/S video device)/stereo amplifier .................................................................... English-23
[P-5] Installing the expansion module ................................................................................................................................................ English-24
Installation of the expansion module ..................................................................................................................................... English-24
SDI for long-distance connection or multiple-monitor connection ........................................................................................ English-24
Connecting OPS-compliant computer................................................................................................................................... English-25
[P-6] Connecting RS-232C ................................................................................................................................................................. English-26
Monitor control via RS-232C ................................................................................................................................................. English-26
[P-7] Connecting LAN......................................................................................................................................................................... English-27
Monitor connection using LAN .............................................................................................................................................. English-27
[P-8] Connecting a USB device .......................................................................................................................................................... English-28
Connecting multiple USB devices using the USB hub function ............................................................................................ English-28
[P-9] Connecting the power cord to the monitor................................................................................................................................ English-29
Connecting the power source ................................................................................................................................................ English-29
How to Use............................................................................................................................................................................................ English-30
Flow of How to Use................................................................................................................................................................ English-30
[U-1] Turning on all the connected devices ........................................................................................................................................ English-31
Turning on external devices ................................................................................................................................................... English-31
Turning on the monitor ........................................................................................................................................................... English-31
Power Management Function ................................................................................................................................................ English-32
[U-2] Selecting the video input ........................................................................................................................................................... English-33
[U-3] Controlling the external devices ................................................................................................................................................ English-34
[U-4] Selecting the OSD language ...................................................................................................................................................... English-34
[U-5] Auto-setup ................................................................................................................................................................................. English-35
[U-6] Selecting the picture mode ........................................................................................................................................................ English-36
[U-7] Screen adjustment ..................................................................................................................................................................... English-36
[U-8] Picture adjustment ..................................................................................................................................................................... English-37
[U-9] Speaker setting .......................................................................................................................................................................... English-37
[U-10] Volume, balance, and tone control ............................................................................................................................................ English-38
[U-11] Schedule setting ........................................................................................................................................................................ English-39
How to set up schedule ......................................................................................................................................................... English-40
[U-12] Remote control .......................................................................................................................................................................... English-41
RS-232C Remote control ....................................................................................................................................................... English-41
LAN Remote control............................................................................................................................................................... English-43
[U-13] Setting the USB hub .................................................................................................................................................................. English-44
Configuration and basic operation of OSD screen ............................................................................................................................... English-45
Configuration of OSD screen ................................................................................................................................................. English-45
Basic operation of OSD ......................................................................................................................................................... English-46
OSD screen functions ........................................................................................................................................................................... English-47
Other functions ...................................................................................................................................................................................... English-58
Picture size ............................................................................................................................................................................. English-58
Picture mode .......................................................................................................................................................................... English-58
Control Lock mode ................................................................................................................................................................ English-58
OSD information..................................................................................................................................................................... English-58
Audio input change ................................................................................................................................................................ English-59
Supplemental information of the auto brightness function .................................................................................................... English-60
PIP, POP function .................................................................................................................................................................. English-61
Remote control numbering function ...................................................................................................................................... English-62
Troubleshooting .................................................................................................................................................................................... English-63
Specifications ........................................................................................................................................................................................ English-64
Pin Assignment ..................................................................................................................................................................................... English-65
English-1
English
Index
Features
Industry-use LED backlight adopted
LED backlight panel
Power-on Delay
Page 64
Commercial grade panel adopting the LED backlight.
With the LED backlight, the monitor has achieved low power consumption
and eliminated mercury. The slim monitor design allows installation in more
various environments than the conventional monitors.
High-quality LCD panel which provides a wide variety of
contents and messages clearly
Full HD panel
Page 64
The MDT701S panel reproduces images from video and computer signals
with precision and clarity, delivering full 1920 x 1080 high-definition
resolution.
Page 56
For installations employing numerous monitors, the power-on delay function
can power up the monitors sequentially with delay between 2-50 seconds
after the power is applied. Using this function can prevent inrush current
problems and reduce the overall electrical load requirements when a single
power supply is used.
LAN Control
Pages 27, 43, and 53
You can efficiently and centrally control multiple monitors for reconfiguration
and remote diagnosis by sending control commands from a computer via a
LAN network. The user can choose to use Mitsubishi protocol to control this
monitor, or other popular protocols including Crestron’s RoomView TM and
AMX’s Device Discovery.
Brightness Compensation by the Ambient Light Sensors
for Enhanced Visibility and Lower Power Consumption
Ambient Light Sensors (Brightness sensors)
Enhanced Display Functionality for Various Commercial
Use/Support for System Configuration Suitable for
Diversified Applications
Tiling Capability with Frame compensation
Page 56
Up to 25 panels (5 wide x 5 high) can be combined to create a single large
image (i.e., video wall) or other high-impact signage. A frame compensation
function is incorporated to compensate the width of panel bezels so that
images are displayed with the utmost accuracy.
PIP, POP and Side-by-side
Pages 10, 51, and 61
Pages 8 and 60
Automatic screen brightness adjustment for enhanced visibility and lower
power consumption.
The ambient light sensors on the front and rear of the monitor detect not
only the light reflected on the front but also from the rear to automatically
adjust the image brightness for optimum viewing. The screen is always easy
to view in spite of brightness variation during the day or night.
Others
Picture-In-Picture and Picture-Outside-Picture are available when you want
to display video content from a video input source in the sub picture and
display the PC input source in the main picture, and vice versa.
The native resolution as high as 1920 x 1080 can display these two input
sources in the Side-by-side mode, ideal for broadcasting and videoconferencing applications.
DisplayPort
Digital Zoom
Built-in Speakers
Page 49
Pages 9 and 21
DisplayPort-compliant terminal is provided.
The monitor is equipped with a terminal supporting DisplayPort, a digital
interface standard. You can transmit video signals over a single cable of
max. 15-meters long.
Pages 8 and 37
Zoom mode for expanding 4:3 image to 16:9.
Various zoom modes are provided and it is possible to expand 4:3 aspect
ratio images to 16:9. In addition, you can select the dynamic display mode
to display naturally widened images with different zooming rates around the
screen center and screen edges. You can also optimally change the image
size diagonally, horizontally, and vertically.
This monitor offers built-in stereo speakers to deliver audio messages.
Optional external stereo speakers can also be used. The user have the
option to switch between using external or built-in speakers from the menu.
Expansion slot allowing installation of expansion
modules according to applications
Closed Caption
Option Slot
Page 24
You can mount an expansion module recommended by Mitsubishi on the
monitor. With such expansion module, you can expand the functionality of
the monitor according to the purpose of use.
SDI Connection (option)
Page 24
The SDI BOX receives SD-SDI, HD-SDI, and 3G-SDI signals at a maximum
speed of 2.970 Gbit/s and displays them on the monitor. A single image is
distributed to multiple monitors that are daisy-chained via SDI cables (BNC).
Various Management Functions Supporting Efficient
Operation and Management
Programmable Scheduling Function Pages 39, 40, and 54
The monitor’s operating schedule can be programmed for up to seven
different scheduled time intervals by time, day of the week and input port.
This allows video content from different inputs to be displayed on certain
monitors within the same installation according to the schedule, and extends
the monitor’s life and saves the power by turning it off during those hours or
days it is not in use.
Screen-saver Functions
Page 52
To reduce image persistence and maximize the panel life in demanding
signage applications, this product is equipped with four screen-saver
functions.
• GAMMA
• COOLING FAN
• BRIGHTNESS
• MOTION
Remote Control
Pages 10 and 11
A wireless remote control is supplied to control the various functions of this
monitor, including power on/off, input select, and menu access.
Page 57
You can display captions.
When closed-caption is encoded with the video signal, the user can select
to display or hide the caption on screen.
This monitor is compliant with EIA-608-A.
USB hub function
Page 57
Multiple USB devices can be connected to the computer.
The monitor is equipped with the USB hub having 2 self-powered
downstream ports, where the USB devices can be connected. You will find
this function convenient when mounting a device such as a digital camera
and a touch-panel unit on the monitor.
Super Resolution (image conversion) technique Page 48
Still images/natural images and video content are displayed with enhanced
clarity based on the super resolution settings. In addition, the monitor
is equipped with the resolution recognition function that recognizes the
resolution of the input image and automatically applies the effect depending
on the recognized resolution.
Double-speed Clear Picture (CP MODE)
Page 56
Extra frames are generated from the original 60-frame-per-second image
based on motion estimation and interpolated to display 120 frames per
second. The afterimage effects are reduced and fast-motion images are
displayed smoothly. This function also makes moving objects such as
scrolling tickers easy to view and shows great effect in digital signage
applications where information is conveyed in a short time.
Daisy Chain Connection (DVI-D)
Page 21
By connecting the DVI-D OUT connectors and the DVI-D IN connectors
using DVI-D cables (commercially available), you can transmit video signals
to up to 4 monitors (when using 2-meter cables). This function is useful in
supplying a video signal to multiple monitors.
English-2
Canadian Department of Communications Compliance Statement
DOC: This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2
No. 60950-1.
FCC Information
1. Use the attached specified cables with the MDT701S (A3112) color monitor so as not to interfere with radio and television
reception.
(1) Please use the supplied power cord or equivalent to ensure FCC compliance.
(2) Please use the supplied shielded video signal cable, 15-pin mini D-SUB to 15-pin mini D-SUB.
2. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
3. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.
Windows is a registered trademark of Microsoft Corporation.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing
LLC in the United States and other countries.
VESA, DisplayPort, and the DisplayPort icon are trademarks or registered trademarks of Video Electronics Standards
Association in the United States and other countries.
Intel is a trademark of Intel Corporation in the United States and other countries.
Crestron, Crestron RoomView and RoomView are trademarks or registered trademarks of Crestron Electronics, Inc. in the
United States and other countries.
AMX is a trademark or registered trademark of AMX, LLC in the United States and other countries.
All other brands and product names are trademarks or registered trademarks of their respective owners.
English-3
English
Important Information
Important Information (continued)
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S
POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO
FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET. DO
NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock.
Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been
included. Therefore, it should be read carefully in order to avoid any problems.
English-4
Declaration
We hereby certify that the color monitor MDT701S (A3112)
is in compliance with
Council Directive 2006/95/EC:
— EN 60950-1
Council Directive 2004/108/EC:
— EN 55022
— EN 61000-3-2
— EN 61000-3-3
— EN 55024
and marked with
Mitsubishi Electric Corporation
2-7-3, Marunouchi,
Chiyoda-Ku
Tokyo 100-8310, Japan
Warning
This is a Class A product. In a domestic environment this product may cause radio interference, in which case the
user may be required to take adequate measures.
Declaration of the Manufacturer
Note: This symbol mark is for EU countries only.
This symbol mark is according to the directive 2002/96/EC Article 10 Information for users and
Annex IV, and/or to the directive 2006/66/EC Article 20 Information for end-users and Annex II.
Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and
components which can be recycled and/or reused.
This symbol means that electrical and electronic equipment, batteries and accumulators, at their end-of-life,
should be disposed of separately from your household waste.
If a chemical symbol is printed beneath the symbol shown above, this chemical symbol means that the
battery or accumulator contains a heavy metal at a certain concentration. This will be indicated as follows:
Hg: mercury (0,0005%), Cd: cadmium (0,002%), Pb: lead (0,004%)
In the European Union there are separate collection systems for used electrical and electronic products,
batteries and accumulators.
Please, dispose of this equipment, batteries and accumulators correctly at your local community waste
collection/recycling centre.
Please, help us to conserve the environment we live in!
English-5
English
Declaration of the Manufacturer
Safety Precautions, Maintenance & Recommended Use
FOR OPTIMUM PERFORMANCE, PLEASE NOTE
THE FOLLOWING WHEN SETTING UP AND USING
THE LCD COLOR MONITOR:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
DO NOT REMOVE MONITOR BACK COVER. There are
no user serviceable parts inside and opening or removing
covers may expose you to dangerous shock hazards or
other risks.
Refer all servicing to qualified service personnel.
Do not spill any liquids into the cabinet or use your monitor
near water.
Do not insert objects of any kind into the cabinet slots,
as they may touch dangerous voltage points, which can
be harmful or fatal or may cause electric shock, fire or
equipment failure.
Do not place any heavy objects on the power cord.
Damage to the cord may cause shock or fire.
Do not place this product on a sloping or unstable cart,
stand or table, as the monitor may fall, causing serious
damage to the monitor.
When operating the LCD monitor with its AC 100-120 V
power supply in North America, use a power supply cord
provided with the monitor.
If a power cord is not supplied with this monitor, please
contact your supplier.
When operating the LCD monitor with its AC 220-240 V
power supply in Europe, use a power supply cord provided
with the monitor.
If a power cord is not supplied with this monitor, please
contact your supplier.
In UK, use a BS-approved power cord with molded plug
having a black (10 A) fuse installed for use with this monitor.
When operating the LCD Monitor with a 220-240 V AC
power supply in Australia, use the power cord provided with
the monitor.
If a power cord is not supplied with this equipment, please
contact your supplier.
For all other cases, use a power cord that matches the AC
voltage of the power outlet and has been approved by and
complies with the safety standard of your particular country.
Do not place any objects onto the monitor and do not use
the monitor outdoors.
Do not bend power cord.
Do not use monitor in high temperature, humid, dusty, or
oily areas.
If monitor or glass is broken, do not come in contact with
the liquid crystal and handle with care.
If the LCD monitor is damaged and the liquid crystal leaks
out, do not inhale or swallow it.
Allow adequate ventilation around the monitor, so that heat
can properly dissipate. Do not block ventilated openings or
place the monitor near a radiator or other heat sources.
Do not put anything on top of the monitor.
The power cable connector is the primary means of
detaching the system from the power supply. The monitor
should be installed close to a power outlet, which is easily
accessible.
•
•
Handle with care when transporting. Save packaging for
transporting.
Please clean the holes of back cabinet to reject dirt and
dust at least once a year because of set reliability.
If using the cooling fan continuously, it’s recommended to
wipe holes a minimum of once a month.
When installing the remote control batteries;
- Align the batteries according to the (+) and (-) indications
inside the case.
- Align the (-) indication of the batteries first inside the
case.
CAUTION:
Immediately unplug your monitor from the wall outlet and refer
servicing to qualified service personnel under the following
conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled, or objects have fallen inside the
monitor.
• If the monitor has been exposed to rain or water.
• If the monitor has been dropped or the cabinet damaged.
• If the monitor does not operate normally by following
operating instructions.
Recommend Use
CAUTION:
• For optimum performance, allow 20 minutes for warm-up.
• Rest your eyes periodically by focusing on an object at least
5 feet away. Blink often.
• Position the monitor at a 90° angle to windows and other
light sources to minimize glare and reflections.
• Clean the LCD monitor surface with a lint-free, non-abrasive
cloth. Avoid using any cleaning solution or glass cleaner!
• Adjust the monitor’s brightness, contrast, and sharpness
controls to enhance readability.
• Avoid displaying fixed patterns on the monitor for long
periods of time to avoid image persistence (after image
effects).
• Get regular eye checkups.
Ergonomics
To realize the maximum ergonomic benefits, we recommend
the following:
• Use the preset Size and Position controls with standard
signals.
• Use the preset Color Setting.
• Use non-interlaced signals.
• Do not use primary color blue on a dark background, as
it is difficult to see and may produce eye fatigue due to
insufficient contrast.
English-6
Contents
English
Your LCD monitor (MDT701S) comes with the following:
LCD Display Monitor
MODEL
 User’s Manual
 Video Signal Cable
(Mini D-SUB 15-pin to
Mini D-SUB 15-pin Cable)
 LCD Monitor
 Wireless Remote
Control and AAA
Batteries
*
 Clamper x 2
(For holding the HDMI cables)
 Band x 4
(For the HDMI cable holding
clampers)
 Clamper x 3
(For tying cables)
 Corner protector x 4
 Screw (M3) x 4
(For the corner protectors)
 Protective cover
 Cable holder
(For holding the power cord)
 Label to cover the logo
(Use it as necessary.)
 Label to cover the UL
certification marking
The supplied power cord varies depending on destination.
 Power Cord
For EU
*
 Power Cord
For North America
For the use in the other regions, use a power cord that
matches the AC voltage of the power outlet and has been
approved by and complies with the safety standard of those
regions or countries.
The following components are supplied as option.
• External Speakers
• SDI BOX
English-7
Parts Name and Functions
Buttons, Switch, and Indicator
Front
Rear
Control buttons
ON
OFF
1 Main Power Switch
3 POWER button (
Switches the main power on/off.
Switches the power on/off.
This button doesn’t work when the power indicator is off. Turn
on the main power. (See page 31.)
)
NOTE:
Within 2 seconds after turning off the power by the POWER
button on the wireless remote control or the monitor or by a
communication command, don’t turn off the main power switch,
don’t disconnect the power cord, and don’t turn off the breaker.
If the AC power is turned off immediately after the power-off
operation, all the OSD settings including the language selection
may be reset to the factory defaults at the next power-on.
If the OSD settings are reset to the factory defaults as
described above, reconfigure the OSD settings using the
following procedure.
1. Turn off the power of the monitor using the wireless remote
control or otherwise.
2. Wait for at least 2 seconds.
3. Turn on the power of the monitor using the wireless remote
control or otherwise.
4. Check and reconfigure the OSD settings.
Displays the OSD menu to switch the video input.
You can select [HDMI1], [HDMI2], [DVI-D], [D-SUB], [OPTION]*,
[DISPLAYPORT], [YPbPr], [S-VIDEO], or [VIDEO] using the UP
( ) or DOWN ( ) button.
* OPTION can be used when an expansion module is
mounted on the option slot.
2 Remote control sensor and Power indicator
Acts as (-) button to decrease the adjustment in the OSD menu.
Decreases the audio output level when the OSD menu is off.
Remote control sensor: Receives the signal from the wireless
remote control.
Power indicator:
Indicates the state of the LCD monitor.
• Steady green:
The power is on.
• Steady red:
The power is off.
Some operations such as power-on
are possible.
• Steady green and red: The LCD monitor is in the sleep
mode.
• Off:
The main power is off.
• Steady red and blinking green: The LCD monitor is in the
schedule standby mode.
• Blinking red:
The LCD monitor has an error
(detected by the self-diagnostic
function).
4 MUTE button
Switches the audio mute on/off.
5 INPUT button
6 PLUS (+) button
Acts as (+) button to increase the adjustment in the OSD menu.
Increases the audio output level when the OSD menu is off.
7 MINUS (-) button
8 UP (
) button
Acts as button to move the highlighted area up to select an
adjustment item in the OSD menu.
9 DOWN (
) button
Acts as button to move the highlighted area down to select
an adjustment item in the OSD menu.
10 EXIT button
Activates the OSD menu when the OSD menu is off.
Acts as EXIT button to go back to the previous OSD menu.
11 Speakers
Audio sound is output from the built-in speakers.
12 Brightness sensor (on the front and rear)
Sensor for the auto brightness function.
(Reference) Control Lock mode
You can lock the operation buttons. See page 58.
NOTE:
For details about the OSD menu operation using the buttons, see “Basic operation of OSD.” (See page 46.)
English-8
Parts Name and Functions (continued)
Rear
Left side
OUT
IN
Main Power Switch
IN
IN
OUT
1 AC IN (3-pin, with earth terminal)
9 LAN connector
Connects with the supplied power cord.
Connects with a LAN cord.
Anti-theft lock slot
You can insert a
Kensington anti-theft
lock key.
2 USB hub
10 VIDEO IN/OUT (S connector/BNC)
USB upstream port (Standard B): 1
To be connected to an external computer.
USB downstream port (Standard A): 2
To be connected to peripheral devices such as digital camera
and touch-panel.
Connects with video equipment.
S-VIDEO IN: S-video input connector (MINI DIN 4-pin)
VIDEO IN: BNC connector
VIDEO OUT: BNC connector
3 DISPLAYPORT IN
Connects with the audio output connector of external
equipment such as a computer, VCR, and DVD player.
Connects with the digital video output of a computer, etc.
11 AUDIO ANALOG IN
4 HDMI1 IN, HDMI2 IN
12 AUDIO ANALOG OUT
Connects with the digital video output of a computer, DVD
player, etc.
Outputs the signal that is supplied to the AUDIO ANALOG IN
connector ( 11 ). Even when HDMI or DISPLAYPORT is selected,
the selected audio is output from the AUDIO ANALOG OUT
connector. Connects with an external audio amplifier, etc.
5 DVI-D IN
Connects with the digital video output of a computer, etc.
6 DVI-D OUT
Outputs the signal that is supplied to the DVI-D IN connector ( 5 ).
7 D-SUB/YPbPr IN
Connects with the analog video output of a computer or the
component video output of a DVD player, etc.
8 RS-232C connector (D-SUB 9-pin)
IN connector:
Connects with the RS-232C OUT connector of a computer or
other connected MDT701S.
OUT connector:
Connects with the RS-232C IN connector of other connected
MDT701S.
NOTE:
Headphones and earphones aren’t supported.
13 EXTERNAL SPEAKER TERMINAL
Connects with the special stereo speakers (option).
14 Option slot
Insert an expansion module (option or commercially available)
in this slot.
CAUTION:
Damage to the product may result or monitor may not function
properly if an incompatible device is installed in this slot. See
page 24.
When mounting an OPS-compliant computer (commercially
available), turn on the cooling fan.
English-9
English
Connectors and Terminals
Parts Name and Functions (continued)
Wireless Remote Control
8 AUDIO INPUT buttons
Selects the audio input according to the video input.
NOTE:
This button works only while any of HDMI1, HDMI2, OPTION (SDI
BOX or OPS-compliant computer), or DISPLAYPORT video
input is selected. See page 59.
9 PIP (Picture-In-Picture) buttons
ON/OFF button:
INPUT button:
Switches the PIP or POP mode on/off.
Selects video to be displayed in the sub
picture.
CHANGE button: Changes the main picture with the sub
picture.
[Description]
PIP: Picture-In-Picture
The sub picture is displayed within the main picture.
POP: Picture-Outside-Picture
The sub picture is displayed to the bottom right of the main
picture.
SBS: Side-By-Side
The main picture and the sub picture are displayed side by
side.
1 POWER button
NOTE:
When the screen size is [CUSTOM] or [REAL], the PIP and POP
modes don’t work.
Switches the power on/off.
* When the Power indicator is not glowing, no controls will
work.
10 STILL button
2 INPUT buttons
Select the input signal from [HDMI1], [HDMI2], [DVI-D], [D-SUB],
[OPTION]*, [DISPLAYPORT], [YPbPr], [S-VIDEO], and [VIDEO].
* OPTION can be used when an expansion module is
mounted on the option slot.
3 PICTURE MODE button
Selects the picture mode from [HIGHBRIGHT], [STANDARD],
[sRGB], and [CINEMA]. See page 36.
HIGHBRIGHT: The brightness is maximized.
STANDARD:
Factory default setting.
sRGB:
Suitable for color matching with sRGBcompliant devices.
CINEMA:
Suitable for viewing movies.
4 DISPLAY button
Displays the screen information. See page 58. When the remote
control mode is LOCK, you can set it back to NORMAL by
holding down the DISPLAY button for at least 5 seconds (see
page 56).
ON/OFF button:
Switches the still picture mode on/off.
CAPTURE button: Captures the new picture.
11 SIZE button
Selects the picture size from [FULL], [NORMAL], [CUSTOM],
[DYNAMIC], and [REAL]. See page 58.
12 MENU button
Switches the OSD menu mode on/off.
13 UP button (
)
Acts as button to move the highlighted area up to select
an adjustment item in the OSD menu. When the PIP mode is
active, this button moves the sub picture up.
14 PLUS button (+)
Acts as (+) button to increase the adjustment in the OSD menu.
When the PIP mode is active, this button moves the sub picture
to the right.
15 EXIT button
Displays the previous OSD menu.
5 SET button
16 DOWN button (
Accepts the settings made in the OSD menu.
Acts as button to move the highlighted area down to select
an adjustment item in the OSD menu. When the PIP mode is
active, this button moves the sub picture down.
6 MINUS button (-)
Acts as (-) button to decrease the adjustment in the OSD menu.
When the PIP mode is active, this button moves the sub picture
to the left.
)
17 MUTE button
Switches the mute function on/off.
7 AUTO SETUP button
18 VOLUME buttons (VOL)
Displays the auto setup menu. See pages 35 and 52.
Pressing the plus (+) side increases the audio output level.
Pressing the minus (-) side decreases the audio output level.
English-10
Parts Name and Functions (continued)
Operating Range of the Wireless Remote Control
Point the wireless remote control toward the LCD monitor’s
remote control sensor during button operation.
Use the wireless remote control within a distance of about 7 m
from the front of the LCD monitor’s remote control sensor and
at a horizontal and vertical angle of within 30° within a distance
of about 3.5 m.
Installing and removing the wireless remote
control batteries
The wireless remote control is powered by 1.5 V AAA batteries.
How to install the batteries
1. Unlock and pull up the cover in the arrow’s direction.
2. Align the batteries according to the (+) and (-) indications
inside the case.
3. Replace the cover.
How to remove the batteries
1. Unlock and pull up the cover in the arrow’s direction.
2. Remove the batteries.
CAUTION:
The remote control system may not function when direct
sunlight or strong illumination strikes the remote control sensor
of the LCD monitor, or when there is an object in the path.
Handling the wireless remote control
*
*
*
*
Do not subject to strong shock.
Do not allow water or other liquid to splash on the wireless
remote control. If the wireless remote control gets wet, wipe
it dry immediately.
Avoid exposure to heat and steam.
Other than to install the batteries, do not open the wireless
remote control.
CAUTION:
Incorrect use of batteries can result in leaks or explosion.
Be careful especially about the following points.
• Place “AAA” batteries matching the (+) and (-) signs on each
battery to the (+) and (-) signs of battery compartment.
• Do not mix battery types.
• Do not combine new batteries with used ones. It causes
shorter battery life or leakage of batteries.
• Remove dead batteries immediately to prevent battery
liquid from leaking into the battery compartment. Don’t
touch exposed battery acid because it causes damage to
your skin.
NOTE:
• When the wireless remote control doesn’t work at all or it
works only within a short distance to the monitor, change
both batteries with new ones.
• If you do not use the wireless remote control for a long
period, remove the batteries.
English-11
English
How to Use the Wireless Remote Control
Preparation for use
Flow of preparation
P-1
Preparation for installation
- Determine the installation location
- Ventilation requirements for enclosure mounting
Page 13
Carry out as necessary
P-2
Installing the monitor
- Using the wall mount or ceiling mount
- Preventing the handles from touching the wall
- Installing in the portrait position
- Attaching the corner protectors
- Using the monitor without the bezel
Pages 14 to 16
Carry out as necessary
P-3
P-4
Installing the optional speakers
Connection procedure
- Wiring diagram
- Prevention of disconnection of HDMI cable
- Connecting with a computer (analog connection)
- Connecting with a computer (digital connection)
- Connecting a video device (component video/HDMI device)
- Connecting a video device (composite video/S video device)/stereo amplifier
Page 17
Pages 18 to 23
Carry out as necessary
P-5
Installing the expansion module
- Installation of the expansion module
- SDI for long-distance connection or multiple-monitor connection
- Connecting OPS-compliant computer
Pages 24 to 25
Carry out as necessary
P-6
Connecting RS-232C
- Monitor control via RS-232C
Page 26
Carry out as necessary
P-7
Connecting LAN
- Monitor connection using LAN
Page 27
Carry out as necessary
P-8
P-9
Connecting a USB device
- Connecting multiple USB devices using the USB hub function
Connecting the power cord to the monitor
- Connecting the power source
The monitor is ready for use.
How to Use
Page 30
English-12
Page 28
Page 29
Preparation for installation
Determine the installation location
CAUTION:
DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY
YOURSELF.
Installing your LCD monitor must be done by a qualified
technician. Contact your dealer for more information.
CAUTION:
MOVING OR INSTALLING THE LCD MONITOR MUST BE
DONE BY TWO OR MORE PEOPLE.
Failure to follow this warning may result in injury if the LCD
monitor falls.
This LCD has a temperature sensor and cooling fan. If the LCD
becomes hot, the cooling fan will turn on automatically. If the
LCD becomes overheated, the “Caution” menu will appear.
If the “Caution” menu appears, stop using the monitor and
allow it to cool. When the LCD monitor is used in an enclosure
or with protection on LCD surface, please check the inside
temperature of the monitor by “HEAT STATUS” (See page 56). If
the temperature is higher than the normal level, set “COOLING
FAN” to ON using the SCREEN SAVER function (See page 52).
When mounting an OPS-compliant computer (commercially
available), turn on the cooling fan.
CAUTION:
Proper operation of the monitor is not guaranteed when it is
mounted upside down, face up, or face down.
IMPORTANT:
Lay the protective sheet, which was wrapped around the LCD
monitor when it was packaged, beneath the LCD monitor so as
not to scratch the panel.
Ventilation requirements for enclosure mounting
To allow heat to disperse, leave space around the monitor as
shown in the figure below.
Wall
Don’t block these holes.
CAUTION:
Don’t block the holes in the rear of the monitor shown in the
figure above. If they are blocked, heat accumulates inside the
monitor, causing breakdown. The upper limit of the operationguaranteed ambient temperature when the monitor is installed
in the landscape position is 40˚C. When installing the monitor
in a case or an enclosure, ensure adequate ventilation to keep
the temperature inside the case 40˚C or lower by providing
a cooling fan or ventilation holes in the case. The upper limit
when the monitor is in the portrait position is 35˚C.
English-13
English
P-1
P-2
Installing the monitor
Using the wall mount or ceiling mount
Lay the screen face down
Lay the protective sheet on a table, which was wrapped around
the monitor when it was packaged, beneath the screen surface
so as not to scratch the screen surface.
This device cannot be used or installed without the Tabletop
Stand or other mounting accessory. Failure to follow the correct
mounting procedures can result in damage to the equipment or
injury to the user or installer. Product warranty does not cover
damage caused by improper installation.
Failure to follow these recommendations can void your
warranty.
For installation, use M6 iron screws (with a loose-proof spring
washer and having a length 10 mm longer than the thickness of
the mounting bracket) and tighten them securely. MITSUBISHI
ELECTRIC recommends using mounting interface that comply
with TÜV-GS and UL1678 standard in North America.
About the metal bracket:
• Use a VESA-compliant metal bracket.
• Before installation, make sure that the installation surface
has sufficient strength.
• Use a metal bracket (commercially available) that is strong
enough to hold the monitor.
• Before installation, check the strength and other properties
to ensure the safety.
• Do not block the heat dissipating holes in the monitor with
the metal bracket. See page 13.
• For details of the mounting procedure and the safe
installation procedure, see the user instructions of the metal
bracket (commercially available) to be used.
• Take measures such as using multiple metal brackets,
holding the monitor at several points, and taking measures
to prevent falling or dropping in case of a problem in the
metal bracket or the installation location.
Table
792.5
Preventing the handles from
touching the wall
792.5
200
By attaching the handles in the opposite orientation, you can
reduce the depth of the monitor.
200
457.5
200
Carry out as necessary
1. Remove the screws that are holding the handles.
200
457.5
Normal handle position
Handle
Screws
(mm)
Protective Sheet
Handles
CAUTION:
For preventing the monitor from falling:
• Install the monitor with metal brackets for wall or
ceiling installation (commercially available) on your own
responsibility. For detailed procedures of installation, refer
to the instructions of the metal brackets.
• To lessen the probability of injury and damage resulting
from fall of the monitor in case of earthquake or other
disaster, be sure to consult the bracket manufacturer for
installation location.
• To lessen the risk of falling of the monitor, thread
commercially available rope through 4 handles of the
monitor and secure the rope to the wall mount brackets or
ceiling mount brackets. Use rope that can bear a load 6
times the weight of the monitor (approximately 275 kg).
• Do not sleep where the monitor may topple over or fall in
case of an earthquake or other disaster.
• Use screws having enough strength to support the LCD
display monitor (made of stainless steel etc.).
Screw x 8
2. Attach the handles in the opposite orientation and secure
them using the screws you have removed in step 1.
Handle position for shallow depth
Handle
Screws
Screw x 8
English-14
P-2
Installing the monitor (continued)
Carry out as necessary
Face-up
English
Installing in the portrait position
The monitor can be installed in the portrait position.
Ensure that the monitor is oriented as shown below.
CAUTION:
• The operating environmental condition (temperature) when
the monitor is in the portrait position is 0˚C to 35˚C.
• Proper operation of the monitor is not guaranteed when it is
not mounted as shown below (upside down, face-up, face
down, etc.).
• When mounting an OPS-compliant computer (commercially
available), be sure to set COOLING FAN to ON using
SCREEN SAVER in the CONFIGURATION1 menu of the
OSD screen function. If it is set to AUTO, the life of the
computer may become shorter than that with it set to ON or
the computer may have trouble.
• In the portrait position, the lifetime of the backlight is
shorter than that in the landscape position.
Face-down
Operation environment for portrait installation
When the monitor is installed in the portrait position, the
following conditions should be satisfied.
Temperature 0 - 35°C / 32 - 95°F
Humidity
20 - 80% (without condensation)
Installation in the portrait position
” logo should be on the LEFT side when
The “
viewed from the front of the monitor.
NOTE:
This monitor doesn’t have a function to rotate displayed
images. To display images in the portrait orientation, use
already rotated images.
Attaching the corner protectors
CAUTION:
It is recommended to use the corner protectors (accessories).
When installing the monitor, hold its body firmly. If you hold the
monitor by the corner protectors when moving it, the monitor
may detaches and fall from the corner protectors, causing
injuries.
Landscape
1. Attach the corner protectors using the accessory screws (c).
Corner protector
(c)
(c)
(c)
90°
Clockwise
(c)
(c)
(c): Screw for attaching the corner protector (M3, 4 pcs.)
Portrait
Portrait
logo
English-15
P-2
Installing the monitor (continued)
Using the monitor without the bezel
Carry out as necessary
3. Peel off the separators from the protective cover (b)
assembled in step 1 and then attach the protective cover to
the LCD panel.
CAUTION:
• MDT701S satisfies the UL requirements as long as it is used
with the bezel attached. When using the monitor without
the bezel, in which case the monitor doesn’t satisfy the UL
requirements, cover the UL certification marking on the rear
panel with the supplied label.
• To prevent static damage to circuit boards, attach the
protective cover to the LCD panel.
CAUTION:
Never touch the circuit boards because they may be
damaged.
1. Assemble the supplied protective cover according to the
following procedure.
(b)
Peel off the separators.
Peel off the separators.
4. Cover the UL certification marking on the rear panel with
the supplied label (c).
2. Unscrew the screws (a) that hold the bezel to remove the
bezel from the monitor.
CAUTION:
If you remove other screws than the screws (a), the bezel
falls apart. If you do so, the bezel may fall, causing injury or
damaging the monitor.
(a)
(a)
(a): Screws for securing the bezel (M3, 18 pcs.)
English-16
(c)
P-3
Installing the optional speakers
Carry out as necessary
1. Install the optional speakers on the monitor.
Use the metal fittings and screws supplied with the optional speakers.
Please refer to Quick Setup Guide of the optional speakers for the detailed installation procedure.
2. Insert the left speaker cable into the SPEAKER (S)(L) on the monitor, and insert the right speaker cable into the SPEAKER (S)(R).
NOTE:
Match the polarity of the speaker cables and that of the terminals (+ (red)/- (black)).
Unmatched polarity may cause problems with audio output.
Right speaker
(option)
Left speaker
(option)
Black(-)
To speaker terminal (L)
SPEAKER (S)(L)
Red(+)
Black(-)
To speaker terminal (R)
SPEAKER (S)(R)
Red(+)
NOTE:
Switch the built-in speaker mode to the optional speaker mode after you power on the monitor.
See the page for How to Use (on page 30) for further details.
CAUTION:
Don’t hold the speakers when moving the monitor.
The monitor and the speakers may be damaged and you may be injured if the monitor falls.
English-17
English
How to install the optional speakers
P-4
Connection procedure
Before making connections
• First turn off the power of all the connected equipment before making connections.
• Refer to the user manual of each piece of equipment.
NOTE:
Please use the audio cable without resistance when the audio output terminal of the audio device and PC is stereo mini-Jack.
When the audio cable with resistance is used, the audio level may be affected or no sound could be heard.
Wiring diagram
LCD monitor (front)
Personal computer
(DVI-D, HDMI, DISPLAYPORT)
LCD monitor
(first monitor)
Stereo amplifier
DVD player or HD disk
player (HDMI, BNC)
Personal computer
(Analog RGB)
LCD monitor (second monitor)
External speakers
English-18
P-4
Connection procedure (continued)
For connecting an HDMI cable to the connector on the monitor, it is recommended to secure the cable using an accessory clamper
to prevent accidental disconnection.
1. Connect an HDMI cable to the connector on the monitor.
2. Secure the HDMI cable using a clamper (accessory) and a band (accessory).
Remove the screw from the monitor.
Attach the clamper to the monitor using
the screw you have removed in step .
HDMI cable
Screw
Secure the HDMI cable and the clamper
using the band.
NOTE:
The band isn’t reusable. The monitor comes
with 2 spare bands.
To replace the band, cut and remove the
existing band and attach a new one of the
same shape (commercially available,
2.5 mm in width and approximately 100 mm
in length).
Clamper (accessory)
Band (accessory)
3. Secure the HDMI cable using a clamper
(accessory).
Clamper (accessory)
English-19
English
Prevention of disconnection of HDMI cable
P-4
Connection procedure (continued)
Connecting with a computer (analog connection)
Analog connection:
(1) Connect a signal cable (mini D-SUB 15-pin – mini D-SUB 15-pin) (accessory) to the D-SUB/YPbPr IN connector.
(2) Select [D-SUB] using the INPUT button on the monitor or the D-SUB button on the wireless remote control. At the moment of
the selection, the audio is automatically switched to [ANALOG].
Audio connection:
• Connect an audio cable (ø3.5-mm stereo mini) (commercially available) to the AUDIO ANALOG IN connector.
Because the audio is automatically switched to [ANALOG] when [D-SUB] is selected, the audio is output just by connecting the
cable.
LCD monitor
(side)
Personal computer
(Analog RGB)
LCD monitor (rear)
Signal cable
(mini D-SUB 15-pin – mini D-SUB 15-pin)
To D-SUB output
To audio output
D-SUB/YPbPr IN
AUDIO
ANALOG IN
Audio cable
(ø3.5-mm stereo mini)
The monitor automatically distinguishes the timings shown in the table below and sets the screen information. When a PC or other
device is connected, it automatically displays images properly. See the page describing AUTO SETUP/AUTO ADJUST.
<Factory preset timing>
Resolution
1
2
3
4
5
6
7
8
640 x 480
800 x 600
1024 x 768
1280 x 720
1280 x 768
1280 x 800
1360 x 768
1440 x 900
Frequency
Horizontal Vertical
31.5 kHz
60 Hz
37.9 kHz
60 Hz
48.4 kHz
60 Hz
45.0 kHz
60 Hz
47.8 kHz
60 Hz
49.7 kHz
60 Hz
47.7 kHz
60 Hz
55.9 kHz
60 Hz
Remarks
Resolution
9
10
11
12
13
14
15
1280 x 1024
1400 x 1050
1680 x 1050
1600 x 1200
1920 x 1080
1920 x 1080
1920 x 1200
Frequency
Remarks
Horizontal Vertical
64.0 kHz
60 Hz
65.3 kHz
60 Hz
64.7 kHz
60 Hz
75.0 kHz
60 Hz
56.2 kHz
50 Hz
67.5 kHz
60 Hz Recommend timing
74.0 kHz
60 Hz CVT Reduced Blanking
NOTE:
When a signal other than 1920 x 1080 is input, characters may be blurred and figures and objects may be distorted.
Images may not be displayed correctly depending on the video card or driver being used.
English-20
P-4
Connection procedure (continued)
Digital connection:
• Connection via the HDMI IN connector
(1) Connect an HDMI cable (commercially available) to the HDMI1 IN or HDMI2 IN connector.
(2) Select [HDMI1] or [HDMI2] according to the connected connector by pressing the INPUT button on the monitor or the HDMI1
or HDMI2 button on the wireless remote control.
• Connection via the DVI-D IN connector
(1) Connect a DVI-D cable (commercially available) to the DVI-D IN connector.
(2) Select [DVI-D] using the INPUT button on the monitor or the DVI-D button on the wireless remote control.
• Connection via the DISPLAYPORT IN connector
(1) Connect a DisplayPort cable (commercially available) to the DISPLAYPORT IN connector.
(2) Select [DISPLAYPORT] using the INPUT button on the monitor or the DISPLAYPORT button on the wireless remote control.
Second monitor connection:
• Connect the DVI-D OUT connector on the first monitor and the DVI-D IN connector on the second monitor using a DVI-D cable
(commercially available).
NOTE:
• In the daisy chain connection, you can connect up to 4 monitors (when using 2-meter cables). However, the maximum number
of connectable monitors may be limited. It is recommended to check the number of connectable monitors in advance in your
installation environment.
• Set RGB of POWER SAVE in the CONFIGURATION1 menu to OFF when using DVI-D in the daisy chain mode.
Audio connection:
• Connect an audio cable (ø3.5-mm stereo mini) (commercially available) to the AUDIO ANALOG IN connector.
When connecting an HDMI cable, select [HDMI1] or [HDMI2] according to the connected connector by pressing the INPUT
button on the monitor or the HDMI1 or HDMI2 button on the wireless remote control. Note that you can select HDMI1, HDMI2, or
ANALOG audio at this time. (You can select HDMI audio only when the video input is [HDMI1] or [HDMI2]. The audio of only the
selected input is output and HDMI is displayed.)
When connecting a DVI-D cable, select [DVI-D] using the INPUT button on the monitor or the DVI-D button on the wireless
remote control. At the moment of the selection, the audio is automatically switched to [ANALOG].
When connecting a DisplayPort cable, select [DISPLAYPORT] using the INPUT button on the monitor or the DISPLAYPORT
button on the wireless remote control. Note that you can select DISPLAYPORT or ANALOG audio at this time.
• To output the audio to the second monitor, connect the AUDIO ANALOG OUT connector on the first monitor and the AUDIO
ANALOG IN connector on the second monitor using an audio cable (ø3.5-mm stereo mini) (commercially available).
Even when HDMI or DISPLAYPORT is selected on the first monitor, the selected audio is output from the AUDIO ANALOG OUT
connector.
NOTE:
• For switching the audio input when an HDMI cable or a DisplayPort cable is connected, see “Audio input change.”
Personal computer
(DVI-D, HDMI)
LCD monitor
(first monitor)
Audio cable
(ø3.5-mm stereo mini)
AUDIO ANALOG IN
DisplayPort cable
DP IN
To audio output
To DP output
HDMI cable
To HDMI output
DVI-D cable
To DVI-D output
HDMI1 IN or HDMI2 IN
DVI-D IN
LCD monitor (first monitor)
DVI-D OUT
LCD monitor
(second monitor)
DVI-D cable
AUDIO ANALOG OUT
AUDIO ANALOG IN
Audio cable
(ø3.5-mm stereo mini)
DVI-D IN
English-21
LCD monitor (second monitor)
English
Connecting with a computer (digital connection)
P-4
Connection procedure (continued)
Connecting a video device (component video/HDMI device)
This monitor can be connected to a video device equipped with component output such as a DVD player.
Refer to the user’s manual of the connected device for details. (Cables shown in the figure below are commercially available.)
• To connect a DVD player equipped with component output to the D-SUB/YPbPr IN connector on the monitor, use a signal cable
(mini D-SUB 15-pin – BNC) and a BNC – RCA adaptor (commercially available).
Select [YPbPr] using the INPUT button on the monitor or the YPbPr button on the wireless remote control. At the moment of the
selection, the audio is automatically switched to [ANALOG].
• To make audio connection, connect an audio cable (ø3.5-mm stereo mini – RCA) to the AUDIO ANALOG IN connector.
Because the audio is automatically switched to [ANALOG] when [YPbPr] is selected, the audio is output just by connecting the
cable.
• To connect a DVD player equipped with HDMI output to the HDMI1 IN or HDMI2 IN connector on the monitor, use an HDMI
cable.
Select [HDMI1] or [HDMI2] according to the connected connector by pressing the INPUT button on the monitor or the HDMI1 or
HDMI2 button on the wireless remote control.
• When connecting an HDMI cable, you can select HDMI1, HDMI2, or ANALOG audio.
(You can select HDMI audio only when the video input is [HDMI1] or [HDMI2].)
DVD player
(HDMI device)
LCD monitor
(side)
HDMI cable
To HDMI output
LCD monitor (rear)
HDMI1 IN or
HDMI2 IN
To video output
AUDIO
ANALOG IN
D-SUB/YPbPr IN
BNC – RCA adaptor
Signal cable (mini D-SUB 15-pin – BNC)
Audio cable
(ø3.5-mm stereo mini – RCA)
English-22
To audio output
DVD player
(component device)
P-4
Connection procedure (continued)
This monitor can be connected to a composite video or S video device or a stereo amplifier.
Refer to the user’s manual of the composite video or S video device or the stereo amplifier for details. (Cables shown in the figure
below are commercially available.)
• To connect a video device to the VIDEO IN connector (VIDEO IN or S-VIDEO IN) on the monitor, use a BNC cable or an S video
cable. For connection to the audio input connector on the monitor, use an audio cable (ø3.5-mm stereo mini – RCA). Connect the
connectors of the audio cable (RCA) correctly. For connection to the VIDEO IN connector, select [VIDEO] using the INPUT button
on the monitor or the VIDEO button on the wireless remote control. For connection to the S-VIDEO IN connector, select [S-VIDEO]
using the INPUT button on the monitor or the S-VIDEO button on the wireless remote control.
• To connect two monitors, connect one end of a BNC cable to the VIDEO OUT connector of the first monitor and the other end to
the VIDEO IN connector of the second monitor.
NOTE:
• In the daisy chain connection, you can connect up to 5 monitors (when using 5-meter cables). However, the maximum number of
connectable monitors may be limited depending on the connected devices to be used. It is recommended to check the number
of connectable monitors in advance in your installation environment.
• When an analog signal is transmitted through the daisy chain, the picture quality such as brightness and sharpness degrades at
the latter devices in the daisy chain connection.
• When different monitors need to be adjusted so that their tint can be identical, such as when using multiple screens, it is
recommended to use a signal distributor (commercially available).
•
•
When connecting a stereo amplifier to the monitor, be sure to turn off the power of the stereo amplifier. For connection to the
AUDIO ANALOG OUT connector on the monitor, use an audio cable (ø3.5-mm stereo mini – RCA). Connect the connectors of
the audio cable (RCA) correctly. Be sure to turn on the monitor first, and then turn on the stereo amplifier.
The selected audio input signal is output from the AUDIO ANALOG OUT connector.
LCD monitor (first monitor)
Audio cable
(ø3.5-mm stereo mini – RCA)
Video device
(composite video/S video device)
To audio output
BNC cable
To video output
S video cable
AUDIO
ANALOG OUT
AUDIO
ANALOG IN
To S video output
LCD monitor (second monitor)
VIDEO IN
VIDEO OUT
S-VIDEO IN
VIDEO IN
BNC cable
Stereo amplifier
Audio cable (ø3.5-mm stereo mini – RCA)
To audio input
External speakers
English-23
English
Connecting a video device (composite video/S video device)/stereo amplifier
P-5
Installing the expansion module
Installation of the expansion module
Install the expansion module to the option slot of this monitor
following the precautions and procedures described in the
manual supplied with the module.
Carry out as necessary
3. Insert the SDI BOX (option) in the option slot and secure it
on the monitor using the 2 screws that you have removed in
step 2.
Option slot
Examples of supported expansion modules:
• SDI BOX (DP-1SDI-3G)
• OPS-compliant computer (commercially available)
Recommended computer (commercially available):
ARK-DS220F-MTSA1E of Advantech Co., Ltd.
SDI BOX (option)
NOTE:
• Please contact module manufacturer for any compatibility
issues.
[Description]
Intel ® OPS (Open Pluggable Specification) is a standard
suggested by Intel Corporation regarding the interface between
the pluggable module mounted on monitors designed for digital
signage applications and the monitors.
Supported OPS features:
• DVI-D
• UART
• Digital audio
• DDC
CAUTION:
Pay careful attention to the position and orientation of the
SDI BOX and insert it as far as it will go. The device may be
damaged if installed in an incorrect position and orientation.
2. Connection with SDI
There are two cases of connection.
• Power control
• USB
• Analog audio
1) Connection to one monitor
1. Connect the video device and the SDI BOX (option) using
an SDI cable (BNC) (commercially available).
NOTE:
When an expansion module is in the option slot, the monitor
doesn’t enter the sleep mode even when POWER SAVE in the
CONFIGURATION1 menu is set to ON. Even when other video
input is selected, the monitor doesn’t enter the sleep mode.
See pages 32 and 52.
NOTE:
A high-spec BNC cable capable of carrying SDI signal is called
SDI cable and distinguished from other BNC cables.
2) Connection to multiple monitors
1. After the connection made in 2-1) above, connect the
SDI OUT connector on the first SDI BOX and the SDI IN
connector on the second SDI BOX using a commercially
available SDI cable (BNC).
SDI for long-distance connection
or multiple-monitor connection
NOTE:
The usable cable length (when SDI BOX (DP-1SDI-3G) is
mounted) is as follows:
• When one SDI BOX is connected: 100 m (3G-SDI)*
* Based on the result of the actual measurement using
the recommended cable. (Recommended cable: 1694A
made by Belden)
1. Mounting the SDI BOX on the monitor
1. Turn off the main power switch of the monitor and
disconnect the power cord.
CAUTION:
Be sure to disconnect the power cord to prevent breakdown
and electric shock.
2. Unscrew 2 screws and remove the option cover.
Option cover
NOTE:
For the connection method and specifications of the SDI BOX,
see the catalog or operation manual of the SDI BOX.
Removal of the SDI BOX
Hold the handle on the SDI BOX for removal.
CAUTION:
Use the handle to extract the SDI BOX only. Pulling on the SDI
cable (BNC) or by other means may cause damage.
NOTE:
Retain the option cover you have removed because it is
replaced when the SDI BOX isn’t mounted.
English-24
P-5
Installing the expansion module (continued)
Carry out as necessary
Connecting OPS-compliant computer
English
Operation of all types of OPS-compliant computers isn’t
guaranteed.
Recommended computer (commercially available):
ARK-DS220F-MTSA1E of Advantech Co., Ltd.
NOTE:
When an OPS-compliant computer (commercially available)
is mounted, set “COOLING FAN” to ON using the SCREEN
SAVER function. See page 52.
1. Mounting the OPS-compliant computer
on the monitor
1. Turn off the main power switch of the monitor and
disconnect the power cord.
CAUTION:
Be sure to disconnect the power cord to prevent breakdown
and electric shock.
2. Unscrew 2 screws and remove the option cover.
Option cover
NOTE:
Retain the option cover you have removed because it is
replaced when the OPS-compliant computer isn’t mounted.
3. Insert an OPS-compliant computer (commercially available)
in the option slot and secure it on the monitor using the 2
screws that you have removed in step 2.
Option slot
OPS-compliant computer
(commercially available)
CAUTION:
Pay careful attention to the position and orientation of the
OPS-compliant computer and insert it as far as it will go.
The device may be damaged if installed in an incorrect
position and orientation.
Removal of the OPS-compliant computer
Hold the handle on the OPS-compliant computer for removal.
CAUTION:
Extract the OPS-compliant computer by using the handle only.
Pulling on the cable or other means may cause damage.
English-25
P-6
Connecting RS-232C
Carry out as necessary
Monitor control via RS-232C
To control this monitor from a computer via a communication, connect this monitor and the computer using an RS-232C cable
(commercially available).
How to connect
•
•
•
Turn off the main power switch of the computer and this monitor. If you make a connection while the power is on, it causes a
failure of the devices.
Connect the computer and this monitor using a reverse type RS-232C cable (commercially available).
In addition, when you connect two or more monitors as shown in the illustration below, connect the RS-232C OUT connector
of the first monitor and the RS-232C IN connector of the second monitor using a reverse type RS-232C cable (commercially
available). By repeating the connection in the similar way, you can connect monitors in a daisy chain configuration.
NOTE:
• Though you can connect up to 26 monitors, the maximum number of connectable monitors may be limited depending on the
installation environment.
LCD monitor (first monitor)
LCD monitor (second monitor)
Computer
(RS-232C connection)
RS-232C OUT
RS-232C IN
RS-232C OUT
RS-232C IN
RS-232C
RS-232C cable
RS-232C cable
NOTE:
When only the 25-pin serial port is equipped as the serial communication port on the computer, a conversion adapter (commercially
available) is necessary for the connection.
English-26
P-7
Connecting LAN
Carry out as necessary
As shown in the illustration below, you can connect this monitor and a computer in network through a LAN hub. Connect the monitor
and the LAN hub using a straight type LAN cable (commercially available).
How to connect
•
•
•
•
Turn off the main power switch of the computer and this monitor. If you make a connection while the power is on, it causes a
failure of the devices.
Connect the computer and the LAN hub using a straight type LAN cable (commercially available).
Connect this monitor and the LAN hub using a straight type LAN cable (commercially available).
When you connect two or more monitors, you can connect the monitor and the LAN hub using a straight type LAN cable
(commercially available) as described above.
LCD monitor (rear)
Computer
(LAN connection)
LAN
LAN cable
LAN
LAN hub
LAN hub
LAN cable
LAN hub
NOTE:
• When you use a cross type LAN cable (commercially available), you can connect the monitor and the computer one-to-one
without using a LAN hub, however, the computer may not be supported. It is recommended to check the operation in advance.
• The image transfer function via the LAN isn’t supported. This monitor isn’t equipped with the host function for controlling other
devices.
English-27
English
Monitor connection using LAN
P-8
Connecting a USB device
Carry out as necessary
Connecting multiple USB devices using the USB hub function
The USB hub of this monitor is equipped with two switchable upstream ports. One is for connecting an external computer, and the
other is for connecting an OPS-compliant computer internally. Only the selected upstream port is connected to the USB hub. Use
the OSD screen function to select the appropriate upstream port. See pages 44 and 57.
1. [When using an external computer]
Connect the USB port (Standard A) on the computer and the USB upstream port (Standard B) on the monitor using a USB cable
(commercially available).
[When using an OPS-compliant computer]
Install an OPS-compliant computer (connected internally).
2. Connect a USB device to the downstream port of this monitor.
Internal structure of the monitor’s USB function
When using an OPS-compliant
computer
Switch
Upstream port
Internal hub
Downstream port
When using an external
computer
USB
USB devices
(mouse, touch panel, etc.)
NOTE:
• The USB hub function cannot control the monitor.
• Up to 5 hubs can be cascaded in the hub function of this monitor. Carry out operation check in advance even if you connect a
device pursuant to the USB standards.
English-28
P-9
Connecting the power cord to the monitor
Before making connections
• Check that the main power switch is off.
•
CAUTION:
When an OPS-compliant computer is installed and the main power switch of the monitor is on, connecting the power source
may cause the computer to power on, causing damage or breakdown of the operation system and the hard disc.
The power outlet socket should be installed as near the equipment as possible and should be easily accessible.
NOTE:
Please refer to “Safety Precautions, Maintenance & Recommended Use” in this manual for proper selection of the AC power cord.
Use the clamper to prevent accidental disconnection of the power cord.
1. Insert the power connector of the power cord fully and
firmly into the AC IN connector of the monitor.
2. Secure the power connector using the cable holder
(accessory).
Main power switch
CAUTION:
Don’t insert the cable holder into the power outlet
socket. Doing so may cause electric shock.
Fit both ends of the cable holder to the monitor.
Cable holder (accessory)
Engage the cable holder in Parts A.
Secure the power connector with the cable holder.
Power connector
3. Secure the power cord using the clamper (accessory).
4. Insert the power plug into the power outlet socket.
• Fully insert the prongs into the power outlet socket.
Loose connection may cause noise.
• Don’t plug and unplug the power cord repeatedly in
a short time of period.
Clamper (accessory)
Power cord (For EU)
Power cord (For North America)
English-29
English
Connecting the power source
How to Use
Flow of How to Use
U-1
Turning on all the connected devices
U-2
Selecting the video input
Page 33
U-3
Controlling the external devices
Page 34
U-4
Selecting the OSD language
Page 34
Pages 31 to 32
D-SUB only
U-5
Auto-setup
Page 35
U-6
Selecting the picture mode
Page 36
U-7
Screen adjustment
Page 36
U-8
Picture adjustment
Page 37
Carry out as necessary
U-9
Speaker setting
Page 37
U-10
Volume, balance, and tone control
Page 38
U-11
Schedule setting
Pages 39 to 40
U-12
Remote control
Pages 41 to 43
U-13
Setting the USB hub
Page 44
English-30
Turning on all the connected devices
Turning on external devices
1. Turn on the connected devices such as
the computer and DVD player.
3. When the power indicator glows
red, press the POWER button on the
monitor.
The power indicator turns green.
Turning on the monitor
CAUTION:
When an OPS-compliant computer is installed as an expansion
module, the computer automatically turns on and starts as the
monitor is turned on.
Don’t turn off the monitor immediately after turning it on
because the computer may be in the startup process. Select
OPTION as the video input and wait for the operating system of
the computer to complete the startup process.
Power button
NOTE:
When the computer doesn’t start within a given period
of time (approx. 1 minute), “OPERATION ERROR” and an
error message are displayed. See the user’s manual of your
computer.
or
2. Turn on the Main Power Switch.
The power indicator turns on green and the monitor turns
on.
The control buttons on the rear, wireless remote control,
and schedule setting don’t work while the main power
switch is off (the power indicator is off).
When using them, check that the Main Power Switch is on
(the power indicator is on).
Power button
Wireless remote
control
NOTE:
Main power switch
Within 2 seconds after turning off the power by the POWER
button on the wireless remote control or the monitor or by a
communication command, don’t turn off the main power switch,
don’t disconnect the power cord, and don’t turn off the breaker.
If the AC power is turned off immediately after the power-off
operation, all the OSD settings including the language selection
may be reset to the factory defaults at the next power-on.
If the OSD settings are reset to the factory defaults as
described above, reconfigure the OSD settings using the
following procedure.
1. Turn off the power of the monitor using the wireless
remote control or otherwise.
2. Wait for at least 2 seconds.
3. Turn on the power of the monitor using the wireless
remote control or otherwise.
4. Check and reconfigure the OSD settings.
English-31
English
U-1
U-1
Turning on all the connected devices (continued)
Power Management Function
This function reduces the power consumption of the monitor
when the keyboard or the mouse is not used for a fixed period
even though the power of the monitor is on.
While this function is working, the screen becomes dark and
the power indicator glows green and red.
This function is available only when a computer equipped
with the VESA-approved DPM Power Management function is
connected to the monitor.
When the power saver in the OSD menu is turned ON, the
power management function works.
RGB: When the sync signal of computer input (HDMI1,
HDMI2, DVI-D, D-SUB, DISPLAYPORT) is terminated,
the monitor will be in the sleep mode in several
seconds.
VIDEO: When the sync signal of video input (YPbPr, S-VIDEO, or
VIDEO) is terminated, the monitor will be in the sleep
mode in approximately 10 minutes.
[Description]
DPM: Acronym for Display Power Management
NOTE:
•
•
The default power management settings (power savers) for
RGB and VIDEO are ON.
When an expansion module is in the option slot, the monitor
doesn’t enter the sleep mode even when POWER SAVE in
the CONFIGURATION1 menu is set to ON. Even when other
video input is selected, the monitor doesn’t enter the sleep
mode.
Power Indicator
Status
Power-on mode
LED
Green
Power-off mode
Red
Power Standby when
“SCHEDULE” is enable
Red On
Green Blinking
Sleep mode
Red, Green
The main power is off.
Diagnosis (Detecting failure)
Off
Red Blinking
* See troubleshooting on page 63.
English-32
U-2 Selecting the video input
 Select using the INPUT buttons on the wireless remote control.
You can select the desired video input by pressing the corresponding INPUT button on the wireless remote control.
Selectable video inputs are [HDMI1], [HDMI2], [DVI-D], [D-SUB], [OPTION]*, [DISPLAYPORT], [YPbPr], [S-VIDEO], and [VIDEO].
* OPTION can be used when an expansion module is mounted on the option slot.
 Select using the INPUT button on the monitor.
When you press the INPUT button on the monitor, the video input OSD menu is displayed and you can select the video input
using the and buttons.
Selectable video inputs are [HDMI1], [HDMI2], [DVI-D], [D-SUB], [OPTION]*, [DISPLAYPORT], [YPbPr], [S-VIDEO], and [VIDEO].
When you press the INPUT button again, the selected video input is displayed.
* OPTION can be used when an expansion module is mounted on the option slot.
NOTE:
The selection you make doesn’t complete unless you press the INPUT button while the video input OSD menu is displayed. The
time during which the video input OSD menu is displayed is same as that of the INFORMATION OSD. See page 54.
HDMI1
HDMI2
DVI-D
D-SUB
OPTION
DISPLAYPORT
YPbPr
S-VIDEO
VIDEO
INPUT button
Video input OSD menu
Select using the
buttons.
English-33
and
English
You can select the desired video input using the wireless remote control or the INPUT button on the monitor.
U-3 Controlling the external devices
To control the connected external devices, display images on the monitor.
DVD player, etc.
Personal computer
U-4 Selecting the OSD language
Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor.
Using LANGUAGE in the CONFIGURATION1 menu of the OSD screen function, you can select the OSD language. See page 52.
English-34
U-5 Auto-setup
Press the AUTO SETUP button on the wireless remote control to directly display the AUTO SETUP menu of the OSD screen
function.
Alternatively, press the MENU button on the wireless remote control or the EXIT button on the rear of the monitor to display the OSD
screen, and then display the AUTO SETUP menu by selecting AUTO SETUP in the CONFIGURATION1 menu.
By pressing the SET button, you can automatically and properly adjust the screen size, horizontal/vertical position, clock, clock
phase, and input signal level.
NOTE:
The auto setup works on D-SUB only.
AUTO SETUP menu screen
Displaying the
AUTO SETUP
menu directly
Displaying the
OSD menu
English-35
English
analog inputs only
U-6 Selecting the picture mode
Using the PICTURE MODE button on the wireless remote control, you can select the picture mode suitable for images to be
displayed.
HIGHBRIGHT:
STANDARD:
sRGB:
CINEMA:
The brightness is maximized.
Factory default setting.
Suitable for color matching with sRGB-compliant devices.
Suitable for viewing movies.
NOTE:
• “sRGB” can be selected for computer input (HDMI1*, HDMI2*, DVI-D, D-SUB, OPTION
(OPS-compliant computer), and DISPLAYPORT).
• “CINEMA” can be selected for video input (HDMI1*, HDMI2*, OPTION (SDI), YPbPr,
VIDEO, and S-VIDEO).
*
U-7
Automatically selected depending on the input signal.
Screen adjustment
When images aren’t displayed properly even after the auto setup, adjust the screen settings.
Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor.
Using the SCREEN menu of the OSD screen function, you can adjust the horizontal/vertical position, clock, clock phase, zoom
mode, custom zoom, and horizontal/vertical resolutions to obtain proper screen condition.
NOTE:
The position adjustment works on D-SUB, YPbPr, S-VIDEO, and VIDEO only.
The clock adjustment and the resolution adjustment work on D-SUB only.
The zoom adjustment works on all video inputs.
English-36
Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor.
Using the PICTURE menu of the OSD screen function, you can adjust the picture settings such as the brightness, contrast, and
sharpness to obtain desired image quality.
U-9 Speaker setting
Carry out as necessary
Select the built-in speakers or the external special stereo speakers (option) in the speaker setting in the OSD menu.
Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor.
Using SPEAKER in the AUDIO menu of the OSD screen function, you can select the speakers.
English-37
English
U-8 Picture adjustment
U-10 Volume, balance, and tone control
Carry out as necessary
Volume control
You can control the volume level using the VOL button on the wireless remote control.
Balance and tone adjustment
You can adjust the speaker balance, treble, and bass using the AUDIO menu of the OSD screen function.
For adjustment, display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear
of the monitor.
NOTE:
If no audio is output when an OPS-compliant computer is in use, check that the monitor is selected as the audio output source by
the operating system of the computer. For the selection method, see the help or the user’s manual of the operating system for the
computer or the driver for the audio device.
English-38
U-11 Schedule setting
Carry out as necessary
English
Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor.
Using SCHEDULE in the CONFIGURATION2 menu of the OSD screen function, you can program power-on/off and input selection.
English-39
U-11 Schedule setting (continued)
Carry out as necessary
How to set up schedule
Check box
Radio button
Program number selection
When the cursor is in any of the check boxes showing the program numbers 1 to 7 on the left side of the screen, press the UP (
or DOWN ( ) button to move the cursor up or down to select the program number you want to set.
To enable the selected program number, press the SET button to place a checkmark in the check box. To disable it, clear the
checkmark.
)
Schedule setting of each program
When the cursor is in any of the check boxes, pressing the PLUS (+) button moves the cursor into the white frame on the right.
When the cursor is at any of the items within the white frame, pressing the PLUS (+) button moves the cursor to the right, and MINUS (-)
button to the left.
You can set the power-on/off time and video input by pressing the UP ( ) or DOWN ( ) button. In addition, you can select or
deselect the radio buttons by pressing the SET button.
ON:
OFF:
INPUT:
EVERY DAY:
MON - SUN:
EVERY WEEK:
Set the time when the power is turned on. If you don’t want to set the power-on time, enter “--.”
Set the time when the power is turned off. If you don’t want to set to the power-off time, enter “--.”
Displays the video input selected when the power is turned on. If you want to select the video input that was
selected before the power is turned on, enter “--.” When you set the ON time and the video input, you can
switch the video input alone.
Select this option to execute the schedule every day. When you select EVERY DAY, you cannot select any days
of the week and EVERY WEEK.
Select the days of the week on which you want to execute the schedule. Unless you select EVERY WEEK, too,
the selection of the days of the week is cleared after the schedule is executed one time.
Select this option to execute the schedule on the selected days of the week, every week.
Schedule confirmation
To confirm the schedule, press the MENU button on the wireless remote control or the EXIT button on the rear of the monitor to exit
the SCHEDULE menu of the OSD screen function.
If you turn off the power before exiting the SCHEDULE menu, the schedule settings may be canceled.
NOTE:
• Before making the schedule settings, be sure to check the current date and time using “DATE AND TIME.”
• When you close the SCHEDULE screen, the settings are saved.
• When two or more schedules are enabled, they are executed in descending order of the program number, and the power is
turned off upon completion of the last executed schedule.
• When there are two or more schedules having the same power-on/off time, the one having the largest program number is
executed.
• You cannot set the power-on time and the power-off time to the same time.
• When OFF TIMER is ON, the schedule settings are ignored.
• When the main power switch or AC power supply turns off or the circuit breaker trips due to power failure or other causes, the
schedule programs you set aren’t executed.
English-40
U-12 Remote control
Carry out as necessary
When the monitor is connected directly to a computer using an RS-232C cable (commercially available), the following operations
can be controlled via a communication. Select the communication interface (RS-232C) used for the serial communication function.
(See page 53.)
•
•
•
•
•
Power ON or OFF
Switching between input signals
Volume control and mute
Auto setup
Check of the internal temperature of the monitor, etc.
NOTE:
For connection with a 25-pin serial port connector on the computer, a conversion adapter (commercially available) is required.
1) Interface
PROTOCOL
RS-232C
BAUD RATE
9600 [bps]
DATA LENGTH
8 [bit]
PARITY BIT
NONE
STOP BIT
1 [bit]
FLOW CONTROL
NONE
•
For direct connection using RS-232C, use the RXD, TXD, and GND lines.
2) Control command diagram
The command is structured by the address code, function code, data code and end code. The length of the command is
different for each function.
NOTE:
• This example shows a basic command that is used when a single computer and a single monitor are connected.
When you want to connect multiple monitors or perform complicated control using other commands than the basic
commands, contact your dealer for advanced command specifications.
• To send commands with a keypad using terminal software, select “2s” or “30s” for CONTROL TIME OUT in
CONFIGURATION2 in the OSD menu. (Follow the same procedure for LAN control.)
Address code
Function code
Data code
End code
HEX
30h 30h
Function
Data
0Dh
ASCII
‘0’ ‘0’
Function
Data
[Address code]
[Function code]
[Data code]
[End code]
30h 30h (ASCII code, ‘0’ ‘0’), fixed.
Code unique to each control function.
Data unique to each control function (Not always indicated by numerical values.)
0Dh (ASCII code, ‘ ’) fixed.
3) Control sequence
(1) A command is sent from the computer to the monitor. (Commands should be sent at intervals of at least 600 ms.)
(2) The monitor sends a return command within 600 ms* after receiving the end code. If the monitor fails to receive the
command, it doesn’t send any return command. (*During the power-on/off or input selection process, the transmission of the
return command may take more than 600 ms.)
(3) The computer checks the return command to see whether the command it sent was received or not. The computer must
receive the return command before sending the next command.
(4) The monitor sends various codes other than commands including the return command. While RS-232C control sequence is
in progress, the computer must reject the codes.
Example: Turn the power ON (‘ ’ is for ASCII code)
Control command from
computer
Return command from
monitor to computer
30 30 21 0D
‘0’ ‘0’ ‘!’ ‘ ’
Description of command
Sending a command for
power-on
30 30 21 0D
‘0’ ‘0’ ‘!’ ‘ ’
Command received
(Command echoed back)
English-41
English
RS-232C Remote control
U-12 Remote control (continued)
Carry out as necessary
4) Operation commands
The operation commands configure the basic operation settings of this LCD monitor. The commands may not work during signal
switchover.
The operation commands have no data codes.
Operation
POWER ON
POWER OFF
ASCII
!
"
HEX
21h
22h
FORCE POWER OFF WITH OPS*
""
22h 22h
INPUT HDMI1
_r1
5Fh 72h 31h
INPUT HDMI2
_r7
5Fh 72h 37h
INPUT DVI-D
_r2
5Fh 72h 32h
INPUT D-SUB
_r3
5Fh 72h 33h
INPUT OPTION**
_r5
5Fh 72h 35h
INPUT DISPLAYPORT
_r6
5Fh 72h 36h
INPUT VIDEO
_v1
5Fh 76h 31h
INPUT YPbPr
_v2
5Fh 76h 32h
INPUT S-VIDEO
_v3
5Fh 76h 33h
VOLUME UP
r06
72h 30h 36h
VOLUME DOWN
r07
72h 30h 37h
AUTO SETUP
r09
72h 30h 39h
AUDIO MUTE
ra6
72h 61h 36h
* Used when the OPS-compliant computer makes no response.
** OPTION can be used when an expansion module is mounted on the option slot.
•
•
•
•
•
•
After sending the POWER ON or POWER OFF command, wait for at least 20 seconds to send the next command.
After sending a command for video input selection, wait for at least 5 seconds to send the next command. Otherwise, the
monitor may not reply within 600 ms.
Set the timeout value of the control device on the host side to 30 seconds or longer.
In the power-off mode, only the POWER ON operation command and the power status acquisition commands described in
the next paragraph work.
In the sleep mode, only the POWER ON and POWER OFF operation commands and the power status acquisition commands
described in the next paragraph work.
• When no expansion module is mounted, the FORCE POWER OFF WITH OPS operation command is unavailable.
• When an expansion module is mounted, all the input connectors don’t enter the sleep mode.
After turning off the power using an operation command, wait for at least 2 seconds to turn off the AC power using the main
power switch or the breaker. Otherwise, the OSD settings may be reset to the factory defaults.
English-42
U-12 Remote control (continued)
5) Read command
The computer sends the command without datacode to the monitor.
After receiving this command, the monitor returns the command with datacode including the current status to the computer.
Example: When the computer asks the power status of the monitor, and the status of the monitor is powered-on.
Control command from computer
Return command from monitor to
computer
Description of command
Sending a command for checking the
power status
30 30 76 50 0D ‘0’‘0’‘v’‘P’[enter]
30 30 76 50 31 0D ‘0’‘0’‘v’‘P’‘1’[enter]
Monitor is powered-on.
Structure of the Read-command
Function
POWER
Input
Internal
temperature
ON
OFF (Sleep)
HDMI1
HDMI2
DVI-D
D-SUB
OPTION*
DISPLAYPORT
VIDEO
YPbPr
S-VIDEO
Around the main
board
Around the power
supply
vP
vP
vI
vI
vI
vI
vI
vI
vI
vI
vI
Resolution
1˚C
Resolution
1˚C
ASCII
Data (Receive)
1
0
r1
r7
r2
r3
r5
r6
v1
v2
v3
Function
76 50
76 50
76 49
76 49
76 49
76 49
76 49
76 49
76 49
76 49
76 49
HEX
Data (Receive)
31
30
72 31
72 37
72 32
72 33
72 35
72 36
76 31
76 32
76 33
tc1
(ex.) +25
74 63 31
2B 20 32 35
tc2
(ex.) +31
74 63 32
2B 20 33 31
* OPTION can be used when an expansion module is mounted on the option slot.
NOTE:
The monitor will acknowledge the power-on/off command issued from the OPS-compliant computer, however, it will not execute
the command. This is not a malfunction. For automatic operation, use SCHEDULE in the CONFIGURATION2 menu of the OSD
screen function.
LAN Remote control
When you connect the monitor and the computer using a LAN hub and a LAN cable (see page 27) and then configure the network
settings using LAN SETTING in the CONFIGURATION2 menu of the OSD screen function, you can remote-control the monitor using
the same commands as those for RS-232C.
1. Setting procedure
(1) Select LAN as the communication interface used for the serial communication function. (See page 53.)
(2) Set the following network parameters using the OSD menu. (See page 53.)
• DHCP client ON/OFF, IP address, subnet mask and default gateway.
(3) Set the IP address described above and the port number (63007 or 3007) using the application program of your computer to
perform the socket communication.
(4) Send the same control command as that for RS-232C via TCP/IP socket communication.
(5) Check the return command sent from the monitor. When it is received successfully, the setting is completed.
English-43
English
Carry out as necessary
U-13 Setting the USB hub
Carry out as necessary
NOTE:
•
•
•
USB function may not work depending on the BIOS setting of the computer used, OS, and USB devices. In such a case, refer to
the user’s manual of each device and contact the respective manufacturer.
Up to 5 hubs can be cascaded in the hub function of this monitor. Carry out operation check in advance even if you connect a
device pursuant to the USB standards.
The USB hub function cannot control the monitor.
1. Select the computer to be used.
Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the
monitor.
Using USB UPSTREAM in the ADVANCED OPTION menu of the OSD screen function, you can select the computer (EXTERNAL/
OPS) to be used.
EXTERNAL: External computer is selected.
OPS:
OPS-compliant computer is selected.
2. Check that the USB hub is recognized.
The USB hub of this monitor is detected by the computer, and the OS-standard device driver is installed automatically. Some
computers may not recognize the USB hub even if it is connected. In such a case, install the device driver for the USB hub
referring to the user’s manual of the computer.
NOTE:
It takes several seconds for the computer to recognize this monitor. Do not pull out the USB cable before the monitor is
recognized, and do not repeat connecting/disconnecting of the cable instantaneously.
3. Check that the USB is recognized.
Install the device driver of the USB device after the USB device is detected by the computer. The OS-standard device driver may
be installed automatically.
Some computers may not recognize the USB device even if it is connected. In such a case, see the user’s manual of the USB
device.
English-44
Configuration and basic operation of OSD screen
This monitor is equipped with the OSD (On Screen Display) function for easy screen adjustment. The OSD function allows you to
control the menus displayed on the screen for brightness setting and other settings.
The OSD screen is configured as shown below.
Main Menu Screen
Main menu
Icons other than the one you selected are grayed out.
PICTURE
Page 47
CONFIGURATION1
Page 52
SCREEN
Page 49
CONFIGURATION2
Page 53
AUDIO
Page 50
ADVANCED OPTION
Page 55
PIP
Page 51
Sub menu (Adjustment items)
Adjustment items are displayed.
Adjustment status
The values adjusted by the wireless remote control and the
PLUS (+) and MINUS (-) buttons on the monitor are displayed.
Control button guide
Buttons for controlling the displayed OSD menu are displayed.
Sub menu screen
When you select a sub menu, an OSD screen is displayed.
Sub menus contain information screens, adjustment menu screens, and selection menu screens as shown below.
Sub menu screen: Picture reset (for example)
English-45
English
Configuration of OSD screen
Configuration and basic operation of OSD screen (continued)
Basic operation of OSD
Check that the power indicator illuminates green and the monitor is powered on.
Step
Monitor button
Wireless remote control
OSD screen display
1
Press the MENU button to display the
/
OSD screen and then press the
button to select the main menu.
Press the EXIT button to display the
/
OSD screen and then press the
button to select the main menu.
When you press the SET button to
accept the selected main menu, the
sub menu at the top is selected.
When you press the INPUT button to
accept the selected main menu, the
sub menu at the top is selected.
2
3
Press the
menu.
/
button to select a sub
Press the
menu.
/
button to select a sub
4
Press the SET button to accept the
selected sub menu.
Press the INPUT button to accept the
selected sub menu.
/
button to select the
Press the
setting and then press the SET button
to accept it.
/
button to select the
Press the
setting and then press the INPUT
button to accept it.
5
The OSD screen disappears when you press the MENU button on the wireless remote control 1 time or the EXIT button on the
monitor 3 times after step 5.
NOTE:
Besides the example described above, some items are selected or adjusted by the PLUS (+) and MINUS (-) buttons.
Operate the buttons according to the control button guide displayed at the bottom of the OSD screen.
English-46
OSD screen functions
English
PICTURE

BRIGHTNESS
RED
You can adjust the brightness.
Press the PLUS (+) button to increase the brightness. Press
the MINUS (-) button to decrease the brightness.
NOTE: You cannot adjust this item when BRIGHTNESS of
SCREEN SAVER in the CONFIGURATION1 menu is
ON.

YELLOW
This adjustment doesn’t work in the sRGB picture
mode.
GREEN
NOTE: This adjustment doesn’t work in the sRGB picture
mode.


BLACK LEVEL


COLOR TEMPERATURE
You can adjust the color temperature.
The image becomes reddish as the color temperature
decreases, and it becomes bluish as the color temperature
increases.
NOTE: This adjustment doesn’t work in the sRGB picture
mode.
NOISE REDUCTION
* This function doesn’t work on RGB input signals.
You can adjust the noise reduction level.
Press the PLUS (+) button to increase the value to lessen
the noise.
NOTE: This adjustment doesn’t work in the sRGB picture
mode.
COLOR
[COLOR]:
You can adjust all the colors at the same time. Press the
PLUS (+) button to deepen the colors. Press the MINUS (-)
button to lighten the colors.
[RED], [MAGENTA], [BLUE], [CYAN], [GREEN], or [YELLOW]:
You can adjust each color individually. Press the PLUS (+)
button to deepen the selected color. Press the MINUS (-)
button to lighten the selected color.
NOTE: This adjustment doesn’t work in the sRGB picture
mode.
SHARPNESS
You can adjust the brightness in the dark area of the image.
Press the PLUS (+) button to brighten dark areas in the
image. Press the MINUS (-) button to further darken the
dark area of the image.
NOTE: This adjustment doesn’t work in the sRGB picture
mode.
CYAN
Color circle
You can adjust the sharpness.
Press the PLUS (+) button to make the image look sharper.
Press the MINUS (-) button to make the image look softer.
NOTE: If you increase the sharpness setting value too
much, lines may appear double. In such a case,
decrease the sharpness setting value.

BLUE
CONTRAST
You can adjust the contrast.
Adjust the contrast using the PLUS (+) or MINUS (-) button to
obtain a desired result.
NOTE: Brightness changes luminance of the backlight.
Contrast changes signal levels, and therefore it is
likely to lead to whiteness.

MAGENTA

TINT
[TINT]:
You can adjust all the colors at the same time. Press the
PLUS (+) button to add a green tint. Press the MINUS (-)
button to add a purple tint.
[RED], [MAGENTA], [BLUE], [CYAN], [GREEN], or [YELLOW]:
You can adjust each color individually. Press the PLUS (+)
button to shift the selected color to the right around the
color circle. Press the MINUS (-) button to shift the selected
color to the left around the color circle.
English-47
COLOR CONTROL
The color levels of red, green, and blue are adjusted by the
color bars.
R: Red, G: Green, B: Blue
NOTE: This adjustment doesn’t work in the sRGB picture
mode.
OSD screen functions (continued)

[CONTROL]
PRIMARY:
GAMMA SELECTION
Select this setting to configure the monitor
as Master when controlling multiple
monitors collectively.
SECONDARY: Select this setting to use the monitor
alone or to configure the monitor as
Slave when controlling multiple monitors
collectively.
You can select the gamma mode from NATIVE, S GAMMA,
2.2, 2.4, OPTION, and PROGRAMMABLE.
PROGRAMMABLE can change the GAMMA characteristic
curve via a computer.
Contact your dealer for further details.
NOTE: GAMMA is fixed to 2.2 in the sRGB picture mode.
When PROGRAMMABLE has been selected, the
setting for color temperature is fixed at 6,300 K
(NATIVE).

[LIGHT FROM BACK]
This function is enabled only when [REAR SENSOR] is ON.
When a light source such as a light and a window is behind
the monitor, the rear sensor takes precedence.
YES: Select this setting when there is a light source
such lighting equipment and a window behind the
monitor.
NO: Select this setting when there is no light source
such lighting equipment and a window behind the
monitor.
SUPER RESOLUTION
NOTE: This adjustment doesn’t work in the sRGB picture
mode.
[SUPER RESOLUTION]
Still photos, natural images and videos may benefit with
enhanced resolution by adjusting this setting.
You can adjust the effect at 10 levels using the adjustment
bar (0 to 100) in 10 steps.
[BACK WALL]
This function is enabled only when [REAR SENSOR] is ON.
Select the following settings according to the distance
between the rear of the monitor and the wall or window.
FAR: The distance is 5 meters or longer.
NEAR: The distance is 5 meters or shorter.
[RESOLUTION DETECT]
This function applies optimum effect to the input images
depending on their resolution.
You can set this item when the super resolution level is
other than 0% (off).
AUTO: The resolution of the input image is automatically
recognized and the effect suitable for the
recognized resolution is applied.
HD:
The effect suitable for high resolution images is
applied.
SD:
The effect suitable for standard resolution images
is applied.
LD:
The effect suitable for low resolution images such
as video stream content is applied.
NOTE: The effect of the super resolution technique varies
depending on the type and resolution of the input
image. Noise or flicker may occur depending on the
displayed content.

[FRONT SENSOR]
Select ON for normal use.
OFF: Select this setting when the sensor on the front
panel is shielded.
[REAR SENSOR]
Select ON for normal use.
OFF: Select this setting when the sensor on the rear
panel is shielded.
[SATURATION]
ON: The image saturation is adjusted depending on the
ambient light.
OFF: Image saturation isn’t adjusted.
[VIDEO DETECT]
ON: The screen brightness varies depending on what
are displayed on the screen to reduce power
consumption of the monitor.
OFF: The screen brightness doesn’t vary and the power
consumption isn’t reduced.
AUTO BRIGHTNESS
This function controls the screen brightness depending on
the ambient light for easy viewing.
In addition, it changes the screen brightness depending on
the ambient light and what are displayed on the screen to
reduce power consumption as low as possible.
NOTE: This adjustment doesn’t work in the sRGB or
CINEMA picture mode.

[AUTO BRIGHTNESS]
AUTO:
The settings of AUTO BRIGHTNESS are
adjusted automatically.
NOTE: When you select AUTO, you cannot
adjust any other items than [CONTROL]
individually.
LOCAL: The AUTO BRIGHTNESS function is
enabled and you can adjust [CONTROL] and
subsequent items individually.
REMOTE: The AUTO BRIGHTNESS function is
enabled. In addition, the monitor enters the
intercommunication mode where multiple
monitors are controlled collectively. (See page
60.)
OFF:
This function is disabled.
English-48
PICTURE RESET
You can reset all the PICTURE settings to the factory
defaults.
OSD screen functions (continued)
English
SCREEN


H POSITION
You can adjust the horizontal image position.
Press the PLUS (+) button to move the image to the right.
Press the MINUS (-) button to move the image to the left.

V POSITION
You can adjust the vertical image position.
Press the PLUS (+) button to move the image up. Press the
MINUS (-) button to move the image down.

CLOCK
* For the D-SUB inputs only.
You can adjust the image size of the computer and eliminate
blurred letters.
Press the PLUS (+) button to expand the width of the image
on the screen to the right. Press the MINUS (-) button to
narrow the width of the image on the screen to the left.




V RESOLUTION
* For the D-SUB inputs only.
Use this setting when AUTO SETUP and AUTO ADJUST
cannot obtain the vertical resolution of the input signal.
Press the PLUS (+) button to increase the resolution. Press
the MINUS (-) button to decrease the resolution.
ZOOM MODE
You can select the mode to stretch the image to fit it to the
screen.
For the HDMI1, HDMI2, DVI-D, D-SUB, and DISPLAYPORT
inputs, you can select FULL, NORMAL, CUSTOM, or REAL.
For YPbPr, S-VIDEO, and VIDEO, you can select FULL,
NORMAL, DYNAMIC, CUSTOM, or REAL.
FULL:
The image is stretched to fill the screen
regardless of its aspect ratio.
NORMAL: The image is stretched vertically to the full
height of the screen while keeping the aspect
ratio.
DYNAMIC: The image is stretched to fill the screen with
different magnifications at the screen center
and the screen edges.
CUSTOM: You can stretch the image horizontally and
vertically as you desire using the CUSTOM
ZOOM setting.
REAL:
The image is displayed without being stretched
or reduced.
NOTE: The DYNAMIC mode displays images having the
16:9 aspect ratio, such as those with 1920 x 1080
resolution, in the same way as in the FULL mode.
H RESOLUTION
* For the D-SUB inputs only.
Use this setting when AUTO SETUP and AUTO ADJUST
cannot obtain the horizontal resolution of the input signal.
Press the PLUS (+) button to increase the resolution. Press
the MINUS (-) button to decrease the resolution.
CLOCK PHASE
* For the D-SUB inputs only.
You can adjust the level of the periodic variation of the
screen flicker.
CUSTOM ZOOM
CUSTOM ZOOM becomes selectable when you set ZOOM
MODE to CUSTOM.
ZOOM:
You can expand the horizontal and vertical
sizes simultaneously.
H ZOOM:
You can expand the horizontal size only.
V ZOOM:
You can expand the vertical size only.
H POSITION: Pressing the PLUS (+) button moves the
image to the right. Pressing the MINUS (-)
button moves the image to the left.
V POSITION: Pressing the PLUS (+) button moves the
image up. Pressing the MINUS (-) button
moves the image down.

English-49
SCREEN RESET
You can reset all the SCREEN settings to the factory
defaults.
OSD screen functions (continued)
AUDIO

BALANCE
You can adjust the balance of the right and left volumes.
Press the PLUS (+) button to decrease the left volume.
Press the MINUS (-) button to decrease the right volume.

TREBLE
You can adjust the high frequency sound.
Press the PLUS (+) button to increase the treble sound.
Press the MINUS (-) button to decrease the treble sound.

BASS
You can adjust the low frequency sound.
Press the PLUS (+) button to increase the bass sound.
Press the MINUS (-) button to decrease the bass sound.

SPEAKER
You can switch the built-in speakers and external stereo
speakers (option).
INTERNAL: To output from the built-in speakers
(Maximum output 10 W + 10 W)
EXTERNAL: To output from external speakers
(Maximum output 10 W + 10 W)

AUDIO RESET
You can reset all the AUDIO settings to the factory defaults.
English-50
OSD screen functions (continued)
English
PIP (PICTURE IN PICTURE)
NOTE:
The PIP and POP functions don’t work in the CUSTOM and
REAL picture size modes.
Refer to “PIP, POP function” for details. (See page 61.)


PIP MODE
You can select the PIP mode from PIP, POP, SBS ASPECT,
SBS FULL, and OFF using the PLUS (+) and MINUS (-)
buttons. See page 61.
PIP
POP
SBS ASPECT
SBS FULL
OFF
* SBS: SIDE BY SIDE

PIP SIZE
You can select the size of the sub picture displayed in the
PIP mode.
You can move the sub picture by pressing the UP ( ),
DOWN ( ), PLUS (+), and MINUS (-) buttons.

PIP AUDIO
You can select the audio output in the PIP mode.
When MAIN is selected, audio of the main picture is output.
When SUB is selected, audio of the sub picture is output.

PIP H POSITION
You can adjust the horizontal position of the sub screen.
Press the PLUS (+) button to move the sub screen to the
right. Press the MINUS (-) button to move the sub screen to
the left.

PIP V POSITION
You can adjust the vertical position of the sub screen.
Press the PLUS (+) button to move the sub screen up. Press
the MINUS (-) button to move the sub screen down.

SUB INPUT
You can select the video input for the sub screen from
HDMI, DVI-D, D-SUB, YPbPr, S-VIDEO, and VIDEO.
English-51
PIP RESET
You can reset all the PIP settings to the factory defaults.
OSD screen functions (continued)
CONFIGURATION1

When you select a time period in the MOTION
setting, the monitor enlarges the image and moves it
horizontally and vertically. The portions of the image
out of the display area aren’t visible.
To make the entire image visible all the time, arrange
it to fit within 90% of the screen area at the center.
AUTO SETUP
* For the D-SUB inputs only.
The screen size, horizontal/vertical position, clock, clock
phase, and input signal level are automatically adjusted.

AUTO ADJUST
* For the D-SUB inputs only.
When AUTO ADJUST is ON, the horizontal position, vertical
position, and clock phase are automatically adjusted at the
time of the timing switching.

Motion
90%

LANGUAGE
SCREEN SAVER
You can set the SCREEN SAVER functions to reduce the
risk of “image persistence.”
GAMMA:
When you select ON, the gamma mode where image
persistence is difficult to occur is used.
COOLING FAN:
When you select ON, the cooling fan always runs.
When you select AUTO, the built-in fan automatically starts
running according to the operating temperature.
BRIGHTNESS:
When you select ON, the brightness decreases.
MOTION:
The screen slightly moves horizontally and vertically
at regular intervals to reduce the effect of the image
persistence.
NOTE: While TILING in the ADVANCED OPTION menu is
active, you cannot set MOTION to ON.
COLOR SYSTEM
* For the S-VIDEO and VIDEO inputs only.
You can select the color system depending on the video
device you use.
AUTO:
NTSC, PAL, SECAM, PAL-60 or 4.43 NTSC is
automatically selected.
NTSC:
NTSC
PAL:
PAL
SECAM:
SECAM
4.43NTSC: 4.43 NTSC
PAL-60:
PAL-60
NOTE: When you use a video device purchased from
overseas, set the COLOR SYSTEM menu.
OSD control menus are available in eight languages.
(English, German, Spanish, French, Italian, Swedish,
Chinese, and Japanese)

Move
The portion (shaded part) outside the
display area isn’t displayed.
POWER SAVE
When the power saver in the OSD menu is turned ON, the
power management function works.
RGB: When the sync signal of computer input (HDMI1,
HDMI2, DVI-D, D-SUB, or DISPLAYPORT) is
terminated, the monitor will be in the sleep mode in
several seconds.
VIDEO: When the sync signal of video input (YPbPr,
S-VIDEO, or VIDEO) is terminated, the monitor will
be in the sleep mode in approximately 10 minutes.
NOTE: When an expansion module is in the option slot,
this function is invalid and the monitor doesn’t enter
the sleep mode even when you set this function to
ON. Even when you select other image source, the
monitor doesn’t enter the sleep mode.

Enlarged

SIDE BORDER COLOR
You can adjust the brightness of the area where no images
are displayed when a 4:3 image is displayed in the NORMAL
mode in the ZOOM MODE or the POP or other modes in the
PIP MODE.

CONFIGURATION RESET
The settings made in the CONFIGURATION1 and
CONFIGURATION2 menus are reset to the factory defaults.
However, the LANGUAGE, MONITOR ID, SCHEDULE, and
DATE AND TIME settings aren’t reset.

English-52
FACTORY RESET
The settings made in the PICTURE, SCREEN, AUDIO,
CONFIGURATION1, CONFIGURATION2, and ADVANCED
OPTION menus are reset to the factory defaults.
In addition, the picture mode selected by the wireless
remote control is reset to the factory default.
However, LANGUAGE, CONTROL TIME OUT, MONITOR ID,
SCHEDULE, DATE AND TIME, and DDC/CI aren’t reset.
OSD screen functions (continued)
English
CONFIGURATION2


SERIAL CONTROL
Select the communication interface (RS-232C, OPS (OPScompliant computer), or LAN) for the serial communication
function.
For connection of the signal cable, see page 24 to 28.

LAN SETTING
You can set the communication parameters for the LAN
network.
DHCP CLIENT
Select whether to use DHCP client or not.
Select OFF when not using it, and select ON when using
it.
IP ADDRESS
When DHCP CLIENT is OFF, set the IP address of the
monitor.
When DHCP CLIENT is ON, you can check the value set
by the DHCP server.
SUBNET MASK
When DHCP CLIENT is OFF, set the gateway mask. Set it
to 255.255.255.0 for normal use.
When DHCP CLIENT is ON, you can check the value set
by the DHCP server.
DEFAULT GATEWAY
When DHCP CLIENT is OFF, set the IP address of the
gateway router to externally connect the local area
including the monitor.
When DHCP CLIENT is ON, you can check the value set
by the DHCP server.
PORT
The port number (3007 and 63007) of the monitor is
displayed.
RESET
LAN settings are reset.

CONTROL TIME OUT
When using remote control, the timeout for transmission
intervals among codes within the control command can be
set.
10 ms: Set the time out intervals to 10 milliseconds.
2 s:
Set the time out intervals to 2 seconds.
30 s: Set the time out intervals to 30 seconds.

MONITOR ID
ID numbers for wireless remote control are assigned to
MDT701S monitors that are multi-connected via RS-232C.
ID numbers 1 to 26 are selectable.

OSD TURN OFF
The OSD control menu will stay on as long as it is used.
The preset choices are 5 -120 seconds.

OSD H POSITION
You can adjust the horizontal position of the OSD menu.

OSD V POSITION
You can adjust the vertical position of the OSD menu.

OSD ROTATION
The OSD screen is rotated.
OFF
90L
H MIRROR
V MIRROR
Horizontally
rotated
Vertically
rotated
180
90R
CONTROLLER SETTING
When controlling the monitor via a network using a 2-Series
control processor made by Crestron, set the communication
parameters.
CONTROLLER IP
Set the IP address of the control processor.
PORT NUMBER
Set the port number used for communication.
IP ID
Set the IP identification number.
NOTE: For the detailed setting procedures, see the
operation manual of the control processor made by
Crestron.
English-53
90 degree
rotation
180 degree
rotation
270 degree
rotation
OSD screen functions (continued)

INFORMATION OSD
You can enable and disable the information OSD display.
The display time is selectable from 3 to 10 seconds.
NOTE: The information OSD display shows a message
when the input source is switched, the input signal
state is changed, or the input signal has an error.

OFF TIMER
You can select the OFF TIMER mode.
Select the time period to automatically turn off the power
from 1 to 24 hours.
NOTE: When OFF TIMER is enabled, the SCHEDULE
settings (see page 39) will be disabled.

SCHEDULE
You can program the LCD monitor operation schedules. (See
page 40.)
< HOW TO SETUP SCHEDULE >
Using the “SCHEDULE” function allows you to set up to
seven different scheduled time intervals when the LCD
Monitor will be activated.
You can select the time the monitor turns on and turns off,
the day of week the monitor is activated, and which input
source the monitor will use for each scheduled activation
period. A check mark in the box next to the number of the
schedule indicates that the selected schedule is in effect.
To select which schedule to set, use the up/down arrows to
move the number (1 to 7) of the schedule.
Use the (+) and (-) buttons to move the cursor horizontally
within the particular schedule. Use the and buttons
to increase the time and select the input port. The “SET”
button is used to make a selection.
If you create a schedule but do not want to set the power
on time, select “--” in the “ON” time slot.
If you do not want to use a power off time select “--” in the
“OFF” time slot.
If there is no input selected (“--” showing in the input spot)
the input from the previous schedule will be used.
The selection of EVERY DAY within a schedule takes priority
over other schedules that are set up to operate weekly.
When schedules are overlapping, scheduled Power ON time
has priority over scheduled Power OFF time.
If there are two schedules programmed for the same time,
then the highest numbered schedule has priority.
When OFF TIMER is enabled, the “SCHEDULE” settings are
disabled.

DATE AND TIME
You can adjust the current date and time for the internal
clock.
You must set this item when using SCHEDULE.
After competing the setting, be sure to press the SET
button (button 5 on page 10). When using a button of the
monitor, use the INPUT button (button 5 on page 8).

MONITOR INFORMATION
The model name and the serial number of your monitor are
displayed.
The MAC address of LAN is displayed.
English-54
OSD screen functions (continued)
English
ADVANCED OPTION

* For the D-SUB inputs only.
If the monitor fails to recognize the input signal resolution
correctly, you can select a proper resolution manually.
Only when a signal having a resolution close to any of the
following values from three groups, the values in the most
appropriate group are selectable.
Group 1: AUTO, 1024 x 768, 1280 x 768, 1360 x 768, 1366 x 768
Group 2: AUTO, 1400 x 1050, 1680 x 1050
Group 3: AUTO, 1600 x 1200, 1920 x 1200

When an expansion module is mounted, the
monitor doesn’t enter the sleep mode.
OFF
The video input isn’t selected automatically.

INPUT CHANGE

INPUT DETECT
This function detects whether the video signals are present
or not at the video inputs and automatically select them.
The priority applies when more than one signal is input at
the same time. The signal being displayed isn’t changed
even when a signal with higher priority is input.
AUTO SELECT
The target video inputs are DVI-D and D-SUB. When the
currently selected input signal is lost, this function checks
whether the signal is present at the other input. When
present, the other input is automatically selected.
If no signal is present at both inputs for five seconds, the
monitor enters the sleep mode.
When an expansion module such as the SDI BOX is in the
option slot, OPTION is targeted instead of DVI-D.
The priority of the input signal is as follows:
DVI-D > D-SUB
NOTE: You cannot select other inputs than DVI-D,
OPTION, and D-SUB.
SCAN CONVERSION
* This function doesn’t work when the D-SUB video input
is selected.
It works on interlace signals only.
You can select the IP conversion mode.
PROGRESSIVE: Interlace signals are converted into
progressive signals. Select this setting for
normal cases.
INTERLACE:
Interlace signals are displayed without
being converted. Though this setting is
suitable for motion images, still images
aren’t displayed properly.
You can select the time for input switching from QUICK and
NORMAL.
NOTE: When you select QUICK, slight noise may appear.

SCAN MODE
* This function doesn’t work when the D-SUB video input
is selected.
You can select the image display area.
OVERSCAN: About 95% of the input image is displayed.
UNDERSCAN: Almost 100% of the input image is
displayed.
BLACK LEVEL EXPANSION
* For the HDMI1-HD, HDMI2-HD, DVI-D-HD, DISPLAYPORT
(YCbCr signal), OPTION (YCbCr signal), YPbPr, S-VIDEO,
and VIDEO inputs only.
Select the level of black expansion from OFF, MIDDLE, and
HIGH.

The priority of the input signal is as follows:
HDMI1 > YPbPr > VIDEO > S-VIDEO
NOTE: You cannot select HDMI2, DVI-D, OPTION, and
DISPLAYPORT.
INPUT RESOLUTION

When an expansion module is mounted, the
monitor doesn’t enter the sleep mode.
VIDEO DETECT
The target video inputs are HDMI1, YPbPr, S-VIDEO,
VIDEO, and D-SUB.
When the HDMI1, YPbPr, S-VIDEO, or VIDEO input is
detected, the detected input is automatically selected.
When the video signal being displayed is lost, the D-SUB
input is automatically selected.
English-55
FILM MODE
* This function doesn’t work when the D-SUB video input
is selected.
It works on interlace signals only.
You can select the film mode function.
AUTO: Images of 24 frames per second are detected,
subjected to interpolation, and then displayed.
OFF: The input video signals are displayed without being
subjected to any processing.
NOTE: When FILM MODE is AUTO, set SCAN
CONVERSION to PROGRESSIVE. See page 55.
OSD screen functions (continued)


CP MODE
You can enable the double-speed clear picture function (CP
mode).
Moving images displayed at 60 frames per second are
interpolated into 120-frame-per-second images for smooth
and sharp image quality.
OFF:
Not interpolated
MIDDLE: Interpolated (Typical)
HIGH:
Interpolated (for smoother and sharper image)
NOTE: Frame interpolation may cause noise and smear. To
reduce noise and smear, select OFF.



IR CONTROL
You can lock the wireless remote control.
and
Select from the following 4 modes using the
buttons and then determine the selected mode by pressing
the SET button.
NORMAL:
All the remote control operations are
enabled.
PRIMARY:
The first MDT701S monitor of those multiconnected via RS-232C is designated as
PRIMARY.
SECONDARY: MDT701S monitors other than the first
one multi-connected via RS-232C are
designated as SECONDARY.
LOCK:
All the remote control operations are
disabled.
NOTE: When you hold down the DISPLAY button on the
wireless remote control for at least 5 seconds, the
NORMAL mode is activated.
You can lock the wireless remote control
independently from the control buttons on the rear
of the monitor. See page 58.
POWER ON DELAY
You can adjust the delayed time until the power-on mode
is activated at the time of recovery from the sleep mode or
power-on.
The time is selectable from OFF and 2, 4, 6, 8, 10, 20, 30,
40, and 50 seconds.

TERMINAL SETTING
You can select the mode to display the HDMI1, HDMI2, or
DVI-D signal according to their signal format depending on
their source device.
HDMI SIGNAL:
Select this setting when displaying HDMI1, HDMI2, or
OPTION (when an OPS-compliant computer is mounted).
Select FULL when displaying the signal that uses all 256
levels (from level 0 to 255). This mode is used primarily
when input comes from a computer.
Select LIMITED when displaying the signal that uses 16
to 235 levels of 256 levels for each of R, G, and B. This
mode is used primarily when input comes from a video
device.
HDMI MODE:
Select this setting when displaying the HDMI1 or HDMI2
signal.
Select HDMI-HD when the source device is a video
device.
Select HDMI-PC when the source device is a PC.
TILING
TILING is a function to divide or enlarge images and display
them across multiple screens. You can divide an input video
up to five pieces horizontally and vertically and display
them on a single large screen comprised of up to 25 (5 x 5)
monitors tiled together.
NOTE: A same video signal needs to be input to each
monitor. When different monitors need to be
adjusted so that their tint can be identical, it
is recommended to use a signal distributor
(commercially available).
HEAT STATUS
The statuses of the cooling fan, brightness, and internal
temperature are displayed.
NOTE: The cooling fan starts running according to the
operating temperature or when COOLING FAN is
ON in the SCREEN SAVER menu.
When the operating temperature substantially
exceeds the operation guaranteed range, the
message “TEMPERATURE WARNING” is displayed
on the screen.
DVI MODE:
Select this setting when displaying the DVI-D signal.
Select DVI-PC when the source device is a PC.
Select DVI-HD when the source device is a video
device.

When TILING is activated, PIP, POP, SBS, and STILL
are disabled.
TILING doesn’t work in the REAL picture size mode.
While TILING is active, you cannot set MOTION of
SCREEN SAVER in the CONFIGURATION1 menu to
ON.
H MONITORS:
Select the number of images obtained by
horizontal division.
V MONITORS: Select the number of images obtained by
vertical division.
POSITION:
Select the area you want to enlarge.
FRAME COMP.: When displaying an image across multiple
monitors, you can select the mode to
compensate for the bezel widths for
smooth and natural display.
ENABLE:
When you select ON, the image in the
selected area is enlarged on the screen.
English-56
DDC/CI
Use to turn ON or OFF the DDC/CI communication function.
Select ON for normal use.
OSD screen functions (continued)
CLOSED CAPTION
You can select to display or hide captions.
OFF:
Captions are hidden.
CC1:
Captions are displayed in sync with the
primary audio.
CC2:
Information (related to the primary
audio) is displayed without sync.
CC3:
Captions are displayed in sync with the
secondary audio.
CC4:
Information (related to the secondary
audio) is displayed without sync.
TT1/TT2/TT3/TT4: Four types of information not related to
the displayed images are displayed. (For
example, news and weather forecast.)
NOTE: Check with each supplier of your video software and
external video devices in advance whether they are
compliant with EIA-608-A.
If their video signals are not compliant with it,
images may not be displayed correctly.

USB UPSTREAM
You can select either of the 2 upstream ports and distribute
the signal to 2 downstream ports.
EXTERNAL: External computer is selected.
OPS:
OPS-compliant computer is selected.

ADVANCED OPTION RESET
The settings made in the ADVANCED OPTION menus are
reset to the factory defaults.
However, HDMI MODE, DVI MODE, and DDC/CI aren’t
reset.
English-57
English

Other functions
Picture size
OSD information
HDMI1, HDMI2, DVI-D, D-SUB, OPTION (OPS-compliant
computer), DISPLAYPORT
FULL
NORMAL
CUSTOM
REAL
OPTION (SDI), YPbPr, VIDEO, S-VIDEO
FULL
NORMAL
DYNAMIC
CUSTOM
NORMAL
HDMI1, HDMI2, DVI-D, D-SUB, DISPLAYPORT
DVI-D
1024 x 768
48kHz 60Hz
AUDIO : ANALOG
SIZE : FULL
REAL
NORMAL
(Squeeze signal)
NORMAL
DYNAMIC
Resolution
Horizontal/vertical frequency
Audio input mode
Picture size mode
OPTION (SDI)
OPTION : SDI (3G)
1920 x 1080
67kHz 60Hz
AUDIO : SDI
SIZE : FULL
Normal size of
each signal
NORMAL
Current selection (DVI-D)
FULL
3G-SDI format is selected.
Resolution
Horizontal/vertical frequency
Audio input mode
Picture size mode
Recommend
picture size
OPTION (OPS-compliant computer)
NORMAL:
Images supplied from external devices such
as PC and DVD fit the screen, keeping their
original aspect ratio.
FULL:
Images are displayed on the entire screen.
DYNAMIC:
4:3 images are enlarged on the entire
screen with non-linearity. (Round images
may be cut when enlarged.)
CUSTOM (ZOOM): You can enlarge the displayed images
beyond the active display area. The portions
of the image out of the display area aren’t
visible.
REAL:
Images are displayed in their original sizes.
OPTION : PC
1920 x 1080
67kHz 60Hz
AUDIO : OPS DIGITAL
SIZE : FULL
Current selection
(OPTION (OPS-compliant computer))
Resolution
Horizontal/vertical frequency
Audio input mode
Picture size mode
YPbPr
YPbPr
AUDIO : ANALOG
SIZE : FULL
Current selection (YPbPr)
Audio input mode
Picture size mode
ZOOM
S-VIDEO, VIDEO
S-VIDEO
NTSC
AUDIO : ANALOG
SIZE : FULL
ZOOM
Current selection (S-VIDEO)
Color system mode
Audio input mode
Picture size mode
Picture mode
HDMI1*, HDMI2*, DVI-D, D-SUB, OPTION (OPS-compliant
computer), DISPLAYPORT
HIGHBRIGHT
STANDARD
sRGB
PIP, POP
Main : DVI-D
Sub : S-VIDEO
DVI-D
1024 x 768
48kHz 60Hz
AUDIO : ANALOG
S-VIDEO
NTSC
SIZE : FULL
HDMI1*, HDMI2*, OPTION (SDI), YPbPr, VIDEO, S-VIDEO
HIGHBRIGHT
STANDARD
CINEMA
* Automatically selected depending on the input signal.
Control Lock mode
You can lock the operation buttons so that the image
adjustments you made aren’t changed even when the buttons
are pressed.
By holding down both the and button on the monitor for
3 seconds or longer, you can lock the operation buttons.
By holding down both the and button on the monitor for
3 seconds or longer again, you can unlock the operation
buttons.
English-58
Main picture information
Audio input mode
Sub picture information
Main picture size
Other functions (continued)
You can select the audio input using the AUDIO INPUT button.
Note that the selectable audio inputs vary depending on the currently selected video signal input.
Selection of the video signal input
HDMI1 or HDMI2
Operation
ANALOG
DVI-D
ANALOG only
D-SUB
ANALOG only
PC (OPS-compliant computer)
HDMI*
ANALOG
OPS ANALOG
ANALOG
SDI
ANALOG
DISPLAYPORT
OPTION**
SDI (SDI BOX)
DISPLAYPORT
YPbPr
ANALOG only
S-VIDEO
ANALOG only
VIDEO
ANALOG only
* The audio of HDMI1 or HDMI2 being selected is output as the HDMI audio.
** OPTION can be used when an expansion module is mounted on the option slot.
English-59
OPS DIGITAL
English
Audio input change
Other functions (continued)
Supplemental information of the auto brightness function
To control multiple monitors collectively
In such a case where the tiling function is used, you can control the auto brightness function by sharing the detection result of the
brightness sensor of a certain monitor among the connected monitors.
1. Multi-connect the monitors using RS-232C cables (commercially available) as shown by the example below.
Monitor
ID = 9
(Slave)
Monitor
ID = 8
(Slave)
Monitor
ID = 7
(Slave)
Monitor
ID = 6
(Slave)
Monitor
ID = 5
(Slave)
Monitor
ID = 4
(Slave)
Monitor
ID = 3
Monitor
ID = 2
Monitor
ID = 1
(Slave)
(Slave)
(Master)
Master: Monitor configured as Master that detects the
outside light (Monitor ID is “1”.)
Slave: Monitor controlled by the Master monitor (Monitor
ID is other than “1”.)
2. Assign a monitor ID to each multi-connected MDT701S using MONITOR ID. (See page 53.)
Monitor ID is selectable from 1 to 26.
The monitor ID of the Master monitor should be “1” and those of the Slave monitors should be other than “1”.
You are recommended to assign IDs to the monitors consecutively from 1, 2, 3, and on.
3. Set AUTO BRIGHTNESS on the OSD screen (PICTURE) as follows.
AUTO BRIGHTNESS
CONTROL
Master monitor
LOCAL
PRIMARY
Slave monitors
REMOTE
SECONDARY
To use a computer to control the monitors
When using a computer to control the monitors, you must prepare an application software program for control by yourself.
Brightness of all the monitors can be controlled centrally using a computer, if the customer create a control application to remotely
read the value from two brightness sensors of any monitor and distribute it to all monitors.
1. Connect the RS-232C IN connector of the Master monitor shown above and the RS-232C connector of the computer using an
RS-232C cable.
The communication control function via LAN isn’t supported on the monitor alone, however, it is available when the monitor is
used with the computer.
2. Assign a monitor ID to each multi-connected MDT701S using MONITOR ID. (See page 53.)
Monitor ID is selectable from 1 to 26.
3. Set AUTO BRIGHTNESS on the OSD screen (PICTURE) as follows.
AUTO BRIGHTNESS
CONTROL
Master monitor
REMOTE
SECONDARY
Slave monitors
REMOTE
SECONDARY
4. A control application made by the customer reads the value from two brightness sensors of any monitor and distributes it to all
monitors. For the specifications of the communication commands, contact your dealer.
English-60
Other functions (continued)
The following table shows the combinations of signal inputs with which the “PIP” and “POP” modes function. However, these modes
do not function when the screen size is “CUSTOM” or “REAL”.
Main screen
Sub screen
HDMI1
HDMI2
DVI-D
D-SUB
OPTION*
DISPLAY
PORT
YPbPr
S-VIDEO
VIDEO
HDMI1
×
×
×
×
×
×
×


HDMI2
×
×
×
×
×
×
×


DVI-D
×
×
×
×
×
×
×


D-SUB
×
×
×
×
×
×
×


OPTION*
×
×
×
×
×
×
×


DISPLAYPORT
×
×
×
×
×
×
×


YPbPr
×
×
×
×
×
×
×


S-VIDEO







×
×
VIDEO







×
×
× : Not supported
 : Supported
* OPTION can be used when an expansion module is mounted on the option slot.
By pressing the PIP ON/OFF button on the wireless remote control, you can change the PIP, POP, and SBS modes in the order
shown below.
Alternatively, you can change the modes using the PIP MODE setting of PIP in the OSD main menu. See page 51.
PIP
POP
SBS ASPECT
SBS FULL
OFF
The resolutions in the PIP and SBS FULL modes are as follows:
PIP SIZE
< SMALL >
: 450 pixels X 338 pixels
< MIDDLE >
: 675 pixels X 450 pixels
< LARGE >
: 900 pixels X 675 pixels
SBS FULL
: 960 pixels X 1080 pixels
NOTE:
When the PIP or SBS FULL mode has been selected, images in the sub picture always fit the size of each mode shown above
irrespective of the aspect ratio of the input image.
English-61
English
PIP, POP function
Other functions (continued)
Remote control numbering function
By connecting multiple MDT701S monitors using RS-232C cables, you can control any one monitor or all the monitors by one
remote controller.
1. Assign arbitrary ID number to each of multi-connected MDT701S monitors using MONITOR ID.
ID numbers 1 to 26 are selectable.
It is recommended to assign sequential ID numbers from 1 and up.
2. The remote control mode of the first MDT701S monitor is set to PRIMARY and those of the other monitors are set to
SECONDARY.
3. When you direct the remote controller at the remote control signal sensor of the PRIMARY monitor and press the DISPLAY
button on the remote controller, the ID selection OSD appears at the upper left of the screen.
ID:1
ID No. :2
ID number of the currently viewed monitor
Select the ID number of the monitor you want to control using the +/- button on the remote controller.
The ID of the monitor you want to control is displayed at the upper left of its screen.
By selecting ALL, you can control all the multi-connected monitors.
4. Direct the remote controller at the remote control signal sensor of the PRIMARY monitor.
OSD appears on the monitor having the ID number you selected.
NOTE:
When the ID selection OSD is being displayed on the PRIMARY monitor, press the DISPLAY button on the remote controller again to
cancel the ID selection OSD and then control the monitor you selected.
If you set the remote control mode wrongly and remote control operation becomes unavailable, press any button on the control
panel of the monitor to display the OSD screen and change the remote control mode using ADVANCED OPTION. By pressing and
holding down the DISPLAY button on the remote control for 5 seconds or longer, the remote control mode is initialized to NORMAL.
English-62
No picture
• The signal cable should be securely connected to the display card/computer.
• The display card should be securely seated in its slot.
• The Main Power Switch and the computer power switch should be in the ON position.
• Make sure that the correct mode has been selected on the display card or system being used.
(Please consult the display card or system manual to change the graphics mode.)
• Check the monitor and your display card with respect to the compatibility and recommended settings.
• Check the signal cable connectors for bent or pushed-in pins.
Power button does not respond
• Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.
Image persistence
• Please be aware that LCD Technology may experience a phenomenon known as “image persistence.” Image persistence occurs
when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image
persistence is not permanent, but constant images being displayed for a long period of time should be avoided. To alleviate
image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the
monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.
NOTE:
As with all display devices, MITSUBISHI ELECTRIC recommends displaying moving images and using a moving screen saver at
regular intervals whenever the screen is idle or turning off the monitor when not in use.
Image is unstable, unfocused or swimming is apparent
• Signal cable should be securely attached to the computer.
• Use the OSD Image Adjust controls to focus and adjust the display by increasing or decreasing the fine adjustment.
When the display mode is changed, the OSD Image Adjust settings may need to be re-adjusted.
• Check the monitor and your display card with respect to the compatibility and recommended signal timings.
• If the displayed text is garbled, change the video mode to the non-interlace mode and use 60 Hz refresh rate.
Image of component signal is greenish
• Check to see if the YPbPr input connector is selected.
LED on the monitor is not lit (No green or red color can be seen)
• Power Switch should be in the ON position and power cord should be connected.
• Make certain the computer is not in the power-saving mode (touch the keyboard or mouse).
RED LED on the monitor is blinking
• A certain failure may have occurred. Please contact your nearest authorized MITSUBISHI ELECTRIC service facility.
Displayed image is not sized properly
• Use the OSD Image Adjust controls to increase or decrease the coarse adjustment.
• Make sure that the correct mode has been selected on the display card or system being used.
(Please consult the display card or system manual to change the graphics mode.)
Selected resolution is not displayed properly
• Use OSD Display Mode to enter Information menu and check that the appropriate resolution has been selected. If not, select
corresponding option.
No sound
• Check to see if the speaker cable is properly connected.
• Check to see if the mute is activated.
• Check to see if the volume is set to the minimum level.
Wireless remote control is not available
• Check the wireless remote control’s batteries status.
• Check if the batteries are inserted correctly.
• Check if the wireless remote control is pointing at the monitor’s remote sensor.
“SCHEDULE”/“OFF TIMER” function is not working properly
• The “SCHEDULE” function will be disabled when the “OFF TIMER” is set.
• If the “OFF TIMER” function is enabled and the power to the LCD monitor is turned off if the power supply is interrupted
unexpectedly, then the “OFF TIMER” will be reset.
Either light vertical or horizontal stripes may appear, depending on the specific display pattern. This is no product fault or
degradation.
English-63
English
Troubleshooting
Specifications
Model
MDT701S
Orientation
Landscape/Portrait
88
68
48
21.5
1585
1541
21.5
871
915
Dimension (Unit: mm)
LCD Module
Screen size (diagonal)
69.5” (1765 mm)
Panel Type
VA
Pixel Pitch
0.802 mm
Resolution
1920 x 1080 pixels
Color
Approximately 1.07 billion colors
Brightness (typ.)
500 cd/m2
Contrast ratio
5000 : 1
Viewing Angle (CR>
=10)
Up/Down 176°, Left/Right 176°
Response time
6 ms (Gray to Gray)
Viewable Size (H x V)
1538.9 mm x 865.6 mm / 60.6” x 34.1”
Power Management
VESA DPM
Plug and Play
VESA DDC2B, DDC/CI
Auto Adjustment
Yes (Contrast / Position / Phase / Clock)
OSD user functions
Brightness, Contrast, Black level, Auto brightness, Zoom, PIP, Screen saver, Side border
color, Gamma selection, Heat status, Power on delay, Schedule, Tiling, LAN control, Closed
caption, Super resolution, etc.
Input Connector
Output Connector
PC Input / Output
AV Input / Output
Analog: 15.625/15.734, 31.5 kHz - 91.1 kHz, Digital: 31.5 kHz - 91.1 kHz
Pixel Clock
Storage Environment
Dimension
(W x H x D)
Weight
25.0 - 165.0 MHz
Analog: Analog RGB, Digital: TMDS (with HDCP)
Analog: Separate (TTL), Composite (TTL), Sync on Green, Digital: TMDS
Supported Resolution
640 x 480, 800 x 600, 1024 x 768, 1280 x 768, 1360 x 768, 1280 x 1024,
1600 x 1200 (Compressed/Simplified), 1920 x 1080, 1920 x 1200 (Compressed/Simplified)
(Analog)
Composite <BNC>, Separate (Y/C) <S-TERMINAL>, MINI D-SUB 15-pin (PC/AV Common)
(Digital)
HDMI x 2 (PC/AV Common), SDI (option)
Output Connector
Analog: Composite <BNC>, Digital: SDI (option)
Supported Resolution
Composite/S-terminal: NTSC, PAL, SECAM, 4.43 NTSC, PAL-60
Component: 480i, 480p, 576i, 576p, 1080i, 720p, 1080p
SDI: 480i/576i (SD-SDI), 720p/1080i (HD-SDI), 1080p (3G-SDI)
Output Connector
Slot interface
(Analog)
ø3.5-mm stereo mini jack
(Digital)
HDMI x 2 (digital audio), DISPLAYPORT, SDI (option)
(Analog)
ø3.5-mm stereo mini jack
(Digital)
SDI (option)
Speaker connector L/R (impedance 8 Ω)
Digital (OPS) slot
Audio output 10 W + 10 W (stereo)
Special external speaker (option), audio output 10 W + 10 W (stereo)
Input Connector
RS-232C <D-SUB 9-pin>, LAN <Modular 8-pin>
Output Connector
RS-232C <D-SUB 9-pin>
USB hub
Operation Environment
13.5 - 165.0 MHz
(Digital)
Sync Signal
External Speaker Output
Power Supply
(Analog)
Video Signal
Built-in Speaker Output
Control Input / Output
DVI-D (HDCP supported)
50/58 Hz - 85 Hz
External speaker output
Option slot
HDMI x 2 (PC/AV Common), DVI-D (HDCP supported), DISPLAYPORT
(Digital)
Vertical Frequency
Input Connector
Audio Input / Output
MINI D-SUB 15-pin (PC/AV Common)
(Digital)
Horizontal Frequency
Input Connector
Input / Output Signal
(Analog)
2 upstream / 2 downstream, USB2.0
Input Voltage / Current
2.8 A - 1.3 A @AC100 - 240 V, 50/60 Hz
Power Consumption
278 W (218 W without speaker, option slot)
Power Consumption at Power Saving
Sleep mode: Less than 1.0 W
Power switch off: Less than 1.0 W
Main power switch off: 0 W
Temperature
0 - 40°C / 32 - 104°F (Landscape position), 0 - 35°C / 32 - 95°F (Portrait position)
Humidity
20 - 80% (without condensation)
Temperature
-20 - 60°C / -4 - 140°F
Humidity
10 - 90% (Without condensation) / 90% - 3.5% x (Temp-40°C) regarding over 40°C
Net (without stand)
1585 mm (W) x 915 mm (H) x 68 / 88 mm (D) / 62.4” (W) x 36.0” (H) x 2.7 / 3.5” (D)
Gross
1810 mm (W) x 1145 mm (H) x 306 mm (D) / 71.3” (W) x 45.1” (H) x 12.0” (D)
Net (without stand)
Approximately 45.8 kg / 101.0 lbs
Gross
Approximately 61.5 kg / 135.6 lbs
Wall mounting interface
9-M6 Screws holes (200 mm / 7.9” pitches) for Monitor mount
Complied regulatory and guidelines
UL60950-1 / C-UL / EN60950-1 / CE / BSMI / GOST-R / FCC-A / DOC-A / EN55022-A /
EN55024 / EN61000-3-2 / EN61000-3-3 / C-Tick / RoHS / US Mercury
NOTE: Technical specifications are subject to change without notice.
English-64
Pin Assignment
Pin No
Name
Pin No
Name
1
Video Signal Red
9
+5V (DDC)
2
Video Signal Green
10
SYNC-GND
3
Video Signal Blue
11
GND
4
GND
12
DDC-SDA
5
DDC-GND
13
H-SYNC
6
Red-GND
14
V-SYNC
7
Green-GND
15
DDC-SCL
8
Blue-GND
Mini D-SUB 15-pin
1
5
6
10
11
15
2) Digital RGB input: HDMI
Pin - Assignment of HDMI connector:
1
TMDS Data2+
8
TMDS Data0 Shield
15 SCL
2
TMDS Data2 Shield
9
TMDS Data0-
16 SDA
3
TMDS Data2-
10 TMDS Clock+
17 DDC/CEC Ground
4
TMDS Data1+
11 TMDS Clock Shield
18 +5V Power
5
TMDS Data1 Shield
12 TMDS Clock-
19 Hot Plug Detect
6
TMDS Data1-
13 CEC
7
TMDS Data0+
14
Reserved (N.C. on
device)
HDMI
19
1
2
18
3) Digital RGB input: DVI-D
Pin - Assignment of DVI-D connector:
1
TMDS Data2-
9
TMDS Data1-
17 TMDS Data0-
2
TMDS Data2+
10 TMDS Data1+
18 TMDS Data0+
3
TMDS Data2 Shield
11 TMDS Data1 Shield
19 TMDS Data0 Shield
4
NC
12 NC
20 NC
5
NC
13 NC
21 NC
6
DDC Clock
14 +5V Power
22 TMDS Clock Shield
7
DDC Data
15
8
Analog Vertical Sync
16 Hot Plug Detect
Ground (return for +5V,
23 TMDS Clock+
H-SYNC and V-SYNC)
DVI-D
8
1
9
16
24
17
24 TMDS Clock-
4) Digital RGB input: DISPLAYPORT
Pin No
Name
Pin No
Name
1
ML_Lane 3 (n)
11
GND Top
2
GND
12
ML_Lane 0 (p)
3
ML_Lane 3 (p)
13
CONFIG1
4
ML_Lane 2 (n)
14
CONFIG2
5
GND
15
AUX CH (p)
6
ML_Lane 2 (p)
16
GND
7
ML_Lane 1 (n)
17
AUX CH (n)
8
GND
18
Hot Plug Detect
9
ML_Lane 1 (p)
19
Return
10
ML_Lane 0 (n)
20
DP_PWR
English-65
DISPLAYPORT
19
20
1
2
English
1) Analog RGB input: D-SUB
Pin Assignment (continued)
5) S-VIDEO input (MINI DIN 4-pin)
Pin No
MINI DIN 4-pin
Name
1
GND
2
GND
3
Y (Luminance)
4
C (Chroma)
4
3
2
1
6) RS-232C input/output
Pin No
Name
D-SUB 9-pin
1
NC
2
RXD
3
TXD
4
NC
5
GND
6
NC
7
NC
8
NC
9
NC
1
5
6
9
7) LAN (Modular 8-pin)
Pin# at RJ45
Signal
#1
Orange/White stripe
#2
Orange
#3
Green/White stripe
#4
Blue
#5
Blue/White stripe
#6
Green
#7
Brown/White stripe
#8
Brown
Pair
Modular 8-pin
1234 5678
English-66
MITSUBISHI Contact Information
North America
Europe
Canada (Mitsubishi Electric Sales Canada Inc.)
http://www.mitsubishielectric.ca
Information Technologies Group, 4299 14th Avenue, Markham, Ontario L3R 0J2,
Canada
Sales
Phone
:+1-(905) 475-7728
Fax
:+1-(905) 475-7958
E-mail
:projectors@mitsubishielectric.ca
Technical Phone
:+1-(905) 475-7728
Fax
:+1-(905) 475-7958
Customer Care
E-mail
:support@mitsubishielectric.ca
France (Mitsubishi Electric Europe B.V. French Branch)
25, Boulevard des Bouvets 92 741, Nanterre CEDEX, France
Sales
Phone
:+33 (0)1 55-68-55-07
Fax
:+33 (0)1 55-68-57-31
Technical Phone
:+33 (0)1 55-68-56-42
Fax
:+33 (0)1 55-68-57-31
U.S.A. (Mitsubishi Electric Visual Solutions America, Inc.)
(Warranty Registration)
http://www.mitsubishi-presentations.com
Presentation Products Division, 9351 Jeronimo Road, Irvine, CA 92618, U.S.A.
Phone
Main Line
:+1-(949) 465-6000
Technical
:+1-(888) 307-0309
Product Information :+1-(888) 307-0312
Technical Support
E-mail
:tsupport@mevsa.com
Asia Pacific
Australia (Mitsubishi Electric Australia Pty. Ltd.)
http://www.mitsubishielectric.com.au
348 Victoria Road, Rydalmere, NSW 2116, Australia
Sales
Phone
:+61 2 9684 7777
Fax
:+61 2 9684 7208
E-mail
:mea_vis@meaust.meap.com
Technical Phone
:+61 1300 651 808
E-mail
:service@meaust.meap.com
New Zealand (Black Diamond Technologies Ltd.)
http://www.bdt.co.nz
1 Parliament Street, Lower Hutt Wellington 6009, New Zealand
Sales
Phone
:+64 4 5609100
Fax
:+64 4 5609133
E-mail
:projectorsales@bdt.co.nz
Technical Phone
:+64 4 5609100
Fax
:+64 4 5609133
E-mail
:projectorsales@bdt.co.nz
Hong Kong (Mitsubishi Electric Ryoden Air-Conditioning & Visual Information
Systems (Hong Kong) Ltd.)
http://www.mitsubishi-ryoden.com.hk
9/F, Skyline Tower, 39 Wang Kwong Road, Kowloon Bay, HK
Sales
Phone
:+852-2510 1505
Fax
:+852-2510 0463
E-mail
:mlh02@mlh.mehkg.com
Technical Phone
:+852-2422 0161
Fax
:+852-2487 0181
E-mail
:sc@mlh.mehkg.com
Singapore (Mitsubishi Electric Asia Pte Ltd.)
http://www.mitsubishielectric.com.sg
307 Alexandra Road #05-01/02 Mitsubishi Electric Building 159943, Singapore
Sales
Phone
:+65-6473-2308
Fax
:+65-6475-9503
E-mail
:peripherals@asia.meap.com
Technical Phone
:+65-6473-2308
Fax
:+65-6475-9503
E-mail
:peripherals@asia.meap.com
Malaysia (Melco Sales Malaysia Sdn. Bhd.)
http://www.melcosales.com.my
Lot 11, Jalan 219, P O Box 1036, 46860 Petaling Jaya, Selangor Darul Ehsan,
Malaysia
Sales
Phone
:+603-7955 2088
Fax
:+603-7958 2576
Technical Phone
:+603-7955 3997
Germany (Mitsubishi Electric Europe B.V. German Branch)
http://www.mitsubishi-vis.de
Gothaer Strasse 8, 40880 Ratingen, Germany
Sales
Phone
:+49-2102-4869250
Fax
:+49-2102-4867320
Technical Phone
:+49-2102-4865690
Fax
:+49-2102-4861340
Italy (Mitsubishi Electric Europe B.V. Italian Branch)
Centro Direzionale Colleoni, Palazzo Sirio, Viale Colleoni 7, 20041 Agrate Brianza,
Italy
Sales
Phone
:+39-(0)39-60531
Fax
:+39-(0)39-6053214
E-mail
:info.vis@it.mee.com
The Netherlands (MitsubishiElectric Europe B.V. Benelux Branch)
http://www.MitsubishiElectric.nl
Nijverheidsweg 23a, 3641 RP Mijdrecht, The Netherlands
Sales
Phone
:+31-297-282461
Fax
:+31-297-283936
E-mail
:info@mitsubishi.nl
Technical Phone
:+31-297-282461
Fax
:+31-297-283936
E-mail
:info@mitsubishi.nl
Spain (Mitsubishi Electric Europe B.V. Spanish Branch)
http://www.mitsubishielectric.es
Ctra. de Rubi, 76-80, 08190 Sant Cugat del Valles, Barcelona, Spain
Sales
Phone
:+34-93.565.31.54
Fax
:+34-93.589.43.88
E-mail
:mitsubishi.profesional@sp.mee.com
Technical Phone
:+34-93.586.27.51
Fax
:+34-93.699.74.45
E-mail
:mitsubishi.profesional@sp.mee.com
Sweden (Mitsubishi Electric Europe B.V. Scandinavian Branch)
Hammarbacken 14, Box 750, S-19127, Sollentuna, Sweden
Sales
Phone
:+46-(0)8-6251070
Fax
:+46-(0)8-6251036
Technical Phone
:+46-(0)8-6251052
Fax
:+46-(0)8-6251036
United Kingdom (Mitsubishi Electric Europe B.V. UK Branch)
http://www.mitsubishi.co.uk/evs
Visual Information Systems Division, Travellers Lane, Hatfield, Hertfordshire, AL10
8XB, United Kingdom
Sales
Phone
:+44 (1707) 278684
Fax
:+44 (1707) 278541
E-mail
:projector.info@meuk.mee.com
Technical Phone
:+44 (870) 606 5008
Fax
:+44 (1506) 431927
E-mail
:projector.info@meuk.mee.com
Russia (Mitsubishi Electric Europe B.V. Moscow Representative Office)
52, bldg.3, Kosmodamianskaya Nab, 115054, Moscow, Russian Federation
Sales
Phone
:+7 (495) 721 2070
Fax
:+7 (495) 721 2071
Technical Phone
:+7 (495) 721 2070
Fax
:+7 (495) 721 2071
Thailand (Mitsubishi Electric Kang Yong Watana Co., Ltd.)
http://www.mitsubishi-kyw.co.th
28 Krungthep Kreetha Road, Huamark, Bangkapi, Bangkok 10240, Thailand
Sales
Phone
:+66-2-731-6841
Fax
:+66-2-379-4761
Technical Phone
:+66-2-731-6841
Fax
:+66-2-379-4761
Taiwan (Mitsubishi Electric Taiwan Co., Ltd.)
http://www.mitsubishielectric.com.tw
11th Floor, 88 Sec. 6. Chung Shan N Road. Taipei 111. Taiwan
Sales
Phone
:+886-2-28328255
Fax
:+886-2-28339813
Technical Phone
:+886-2-28328255 ext:3456
Fax
:+886-2-28339813
India (Mitsubishi Electric India Pvt. Ltd.)
http://www.mitsubishielectric.in
Building No.9B, dlf Cyber City Phase3, Gurgaon, Delhi, India
Sales
Phone
:+91-0124-4630300
Fax
:+91-0124-4630399
E-mail
:hitesh.bhardwaj@asia.meap.com
Technical Phone
:+91-0124-4630300
Fax
:+91-0124-4630399
E-mail
:hitesh.bhardwaj@asia.meap.com
AW-P1336A
Printed in China