Preface
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any
person or organization of such revisions or changes.
Manual Revisions
Revision
Date
Description
1.0
September 5, 2012
• Initial release for Revision A1
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United
States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of
their respective companies.
Copyright © 2012 by D-Link Systems, Inc.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission
from D-Link Systems, Inc.
D-Link DAP-1320 User Manual
i
Table of Contents
Table of Contents
Preface.................................................................................. i
Manual Revisions............................................................................ i
Trademarks....................................................................................... i
Product Overview............................................................... 1
Package Contents.......................................................................... 1
System Requirements.................................................................. 2
Wireless Installation Considerations....................................... 3
Introduction.................................................................................... 4
Features............................................................................................. 5
LED.............................................................................................. 6
Installation.......................................................................... 7
Connect your DAP-1320 to your Router................................ 7
Configuration...................................................................... 9
Setup Wizard................................................................................... 9
Web-based Configuration Utility...................................14
Wireless Setup Wizard........................................................15
Setup................................................................................................18
Wi-Fi Setup.............................................................................19
Extended Wi-Fi Setup.........................................................21
Wireless Security..........................................................................22
What is WPA?.........................................................................22
Configure WPA/WPA2 Personal..............................................23
Maintenance.................................................................................24
Admin......................................................................................24
System.....................................................................................25
Language Pack......................................................................26
Firmware.................................................................................26
D-Link DAP-1320 User Manual
Time..........................................................................................27
Status...............................................................................................28
Device Info.............................................................................28
Logs..........................................................................................29
Statistics..................................................................................30
IPv6...........................................................................................31
WPS...................................................................................................32
From Client to DAP-1320..................................................32
Windows® 7....................................................................................33
WPA/WPA2.............................................................................33
Windows Vista®.............................................................................36
WPA/WPA2.............................................................................37
WPS/WCN 2.0........................................................................39
Windows® XP.................................................................................40
WPA/WPA2.............................................................................41
Troubleshooting...............................................................43
Wireless Basics..................................................................45
What is Wireless?..........................................................................46
Tips....................................................................................................48
Networking Basics............................................................49
Statically Assign an IP address................................................50
Technical Specifications...................................................51
Contacting Technical Support.........................................52
Warranty............................................................................53
Registration......................................................................60
ii
Section 1 - Product Overview
Product
PackageOverview
Contents
Wireless Range Extender (DAP-1320)
Wi-Fi Configuration Note
Quick Install Guide
If any of the above items are missing, please contact your reseller.
D-Link DAP-1320 User Manual
1
Section 1 - Product Overview
System Requirements
Network Requirements
• IEEE 802.11n or 802.11g wireless clients
• IEEE 802.11n or 802.11g wireless router or access point
Computer with the following:
• Windows®, Macintosh, or Linux-based operating system
Browser Requirements:
• Internet Explorer 6 or higher
Web-based Configuration
• Safari 4 or higher
Utility Requirements
• Firefox
• Chrome
Windows® Users: Make sure you have the latest version of Java
installed. Visit www.java.com to download the latest version.
D-Link DAP-1320 User Manual
2
Section 2 - Installation
Wireless Installation Considerations
The D-Link wireless device lets you access your network using a wireless connection from virtually anywhere within the
operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings,
or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types
of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to
follow these basic guidelines:
1.Keep the number of walls and ceilings between the D-Link device and other network devices to a minimum each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that
the number of walls or ceilings is minimized.
2.Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle
appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position
devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.
3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect on range.
Try to position access points, wireless routers, and computers so that the signal passes through drywall or open
doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file
cabinets, brick, and concrete will degrade your wireless signal.
4.Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF
noise.
5.If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security
systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone
base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not
in use.
D-Link DAP-1320 User Manual
3
Section 1 - Product Overview
Introduction
The Wireless Range Extender (DAP-1320) enables you to extend your existing wireless network coverage by placing the
Wireless Range Extender in between your router and the wireless client devices. This is great for extending wireless coverage
to basements, home offices or bedrooms that might be distant from your wireless router. The DAP-1320 increases the range
of your wireless network by extending the wireless coverage of an existing wireless network.
Note: Place the DAP-1320 within equal distance of your existing network/router and wireless clients.
D-Link DAP-1320 User Manual
4
Section 1 - Product Overview
Features
•Faster Wireless Networking - The DAP-1320 provides up to 300Mbps* wireless connection with other 802.11n
wireless clients. This capability allows users to participate in real-time activities online, such as video streaming,
online gaming, and real-time audio.
•Extend Internet access for wireless devices - Allows you to extend your internet access throughout your
home with devices such as laptops, Smartphones, tablets and more.
•IEEE 802.11n and 802.11g Compliant - The DAP-1320 is still fully compatible with the IEEE 802.11g standards,
so it can connect with existing 802.11g USB and Cardbus adapters.
* Maximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors,
including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely
affect wireless signal range.
D-Link DAP-1320 User Manual
5
Section 1 - Product Overview
Hardware Overview
LED
1
LED Indicator
Color
Green
1. Power/Status
Amber
D-Link DAP-1320 User Manual
Status
Description
Solid Green
The device is connected to a wireless router or AP
Blinking Green
The device is processing a connection
Light off
The device is off
Blinking Amber
During boot up or a factory reset
Light off
The device is powered off
6
Section 2 - Installation
Installation
Connect your DAP-1320 to your Router
The easiest and most secure way to connect your DAP-1320 to your the router or access point is WPS (Wi-Fi Protected Setup).
Please refer to your user manual for information on your router or access point make sure you understand how to enable WPS.
Once you know, follow the steps below:
Step 1 - Plug the DAP-1320 into a wall outlet and verify if the power
LED has turned from red to a blinking amber.
DAP-1320
Step 2 - Press the WPS button on your AP/Router.
WPS Button
Note: Usually the WPS LED will blink once it is pressed. Check your
router’s manual for more information.
Step 3 - Press and hold the WPS button until the light starts blinking
green and then release. Please allow up to two minutes for
the WPS process to finish. Once the connection is successful
the LED will be solid green.
D-Link DAP-1320 User Manual
WPS Button
7
Section 2 - Installation
Step 4 - Your AP/Router and DAP-1320 will be connected when the LED
light turns solid green.
Note: If connection fails, try moving your DAP-1320 closer to your wireless
router/access point and repeat steps 2 and 3.
Step 5 -To connect your wireless clients to the DAP-1320, use the
Wi-Fi Network SSID and the Wi-Fi Password located on your
configuration note. You may also use WPS to connect your clients
to the DAP-1320 (refer to page 32).
Note: For your wireless client to connect to the DAP-1320, you must use the same Wi-Fi Network Name (SSID) and Wi-Fi password
as your DAP-1320 which is also located on the configuration note. If you would like to change your Wi-Fi Network Name (SSID) and
Wi-Fi password refer to the configuration section page on 18.
D-Link DAP-1320 User Manual
8
Section 3 - Configuration
Configuration
Setup Wizard
1. Plug the DAP-1320 into a wall outlet and verify if the power LED
has turned from red to a blinking amber.
DAP-1320
90mm
2. From your wireless computer go to the Wireless Utility to display
the available wireless networks and select the Wi-Fi Network Name
(SSID) that is located on your configuration note (ex: dlink-a8fa).
Then, enter the Wi-Fi password which is also located on your
configuration note. (ex: akbdj19368).
D-Link DIR-505 Mobile Companion Wi-Fi Configuration Note
54mm
Web browser link:
Web browser link:
http://dlinkrouter or
http:// 192.168.0.1
http://dlinkrouter or
http:// 192.168.0.1
Default configuration
Your configuration
Username: “Admin”
Password: ““ (leave the field blank)
Username: Admin
Password:
Wi- Fi Name (SSID) :
dlinka8fa
Wi-Fi Password :
akbdj19368
Wi- Fi Name (SSID) :
Wi-Fi Password :
3. Open a web browser and type http://dlinkap.local. First time
users will automatically be directed to the setup wizard. Please
follow the on-screen instructions to complete the setup.
D-Link DAP-1320 User Manual
9
Section 3 - Configuration
To start the Setup Wizard click Next.
Select WPS as the configuration method only if your wireless
device supports Wi-Fi Protected Setup (WPS). For manual setup,
skip to page 11.
Click Next to continue.
Press and hold the WPS button on your wireless router or access
point until the light starts blinking green and then release. Please
allow up to two minutes for the WPS process to finish.
D-Link DAP-1320 User Manual
10
Section 3 - Configuration
Select Manual as the configuration method to set up your
network manually.
Click Next to continue.
Please wait while your device scans for available Wi-Fi networks.
D-Link DAP-1320 User Manual
11
Section 3 - Configuration
A list of wireless networks in your area will be listed. Select your
wireless network (associated with your wireless router or access
point) and click Connect to continue.
Enter your Wi-Fi Password for the wireless network you are using
to connect and click Next.
You can choose to change the Wi-Fi Network Name (SSID)
and the Wi-Fi Password for the DAP-1320 or you can enter the
information found on your configuration note. Click Next to
continue and finish the setup process.
Note: Click the check box to use the same Wi-Fi Network Name
(SSID) and the Password for DAP-1320 as your existing network.
D-Link DAP-1320 User Manual
12
Section 3 - Configuration
The setup is now complete. Please click Save to finish.
Please wait while the system reboots.
D-Link DAP-1320 User Manual
13
Section 3 - Configuration
Web-based Configuration Utility
To access the configuration utility, open a web-browser such as
Internet Explorer and enter http://dlinkap.local.
Enter the Password you created when you first logged on during
the setup wizard and click Login.
Note: If you did not create a password before, the default should be
blank.
D-Link DAP-1320 User Manual
14
Section 3 - Configuration
Wireless Setup Wizard
Click Launch Wireless Setup Wizard to begin the Setup Wizard.
Click Next to start the Setup Wizard.
Select WPS as the configuration method only if your wireless
device supports Wi-Fi Protected Setup (WPS).
Click Next to continue.
Press and hold the WPS button on your wireless router or access
point until the light starts blinking green and then release. Please
allow up to two minutes for the WPS process to finish.
D-Link DAP-1320 User Manual
15
Section 3 - Configuration
Select Manual as the configuration method to set up your
network manually.
Click Next to continue.
A list of wireless networks in your area will be listed. Select your
wireless network (associated with your wireless router or access
point) and click Connect to continue.
D-Link DAP-1320 User Manual
16
Section 3 - Configuration
Enter the Wi-Fi Password for the router you are using to connect
and click Next.
You can choose to change the Wi-Fi Network Name (SSID) and
the password for the DAP-1320 or you can enter the information
found in your configuration card. Click Next to continue to finish
the setup process.
Note: Click the check box to use the same Wi-Fi Network Name
(SSID) and the Password for DAP-1320 as your existing network.
The setup is now complete. Please click Save to finish.
Please wait while the system reboots.
D-Link DAP-1320 User Manual
17
Section 3 - Configuration
Setup
To access the configuration utility, open a web-browser such as
Internet Explorer and enter http://dlinkap.local.
Enter the Password you created when you first logged on during
the setup wizard and click Login.
D-Link DAP-1320 User Manual
18
Section 3 - Configuration
Wi-Fi Setup
Use this section to manually configure the wireless settings for your D-Link Repeater.
D-Link DAP-1320 User Manual
19
Section 3 - Configuration
Wireless Mode: This will automatically be Repeater Mode.
Site Survey: Scans and displays available Wi-Fi networks.
Wi-Fi Network When you are browsing for available wireless networks, this is the
Name: name that will appear in the list (unless Visibility Status is set to
Invisible, see below). This name is also referred to as the SSID. For
security purposes, it is highly recommended to change from the
default network name.
Channel Width: Select the Channel Width:
Auto 20/40 - This is the default setting. Select if you are using both
802.11n and non-802.11n wireless devices.
20MHz - Select if you are not using any 802.11n wireless clients.
Security Mode: Select WEP or WPA Personal. Refer to page 22.
D-Link DAP-1320 User Manual
20
Section 3 - Configuration
Extended Wi-Fi Setup
This page allows you to configure the wireless LAN settings for your DAP-1320. You have the option of creating a new Wi-Fi
Network Name for your DAP-1320 or you may use the same Wi-Fi Network Name as your wireless router or AP.
Wi-Fi Network Displays the current Wi-Fi Network Name you are
Name: connected to.
Extended Wi-Fi Select Same as Wi-Fi Network Name or Create a new
Network Name: Wi-Fi Network Name.
Channel Width: Select the Channel Width:
Auto 20/40 - This is the default setting. Select if you are
using both 802.11n and non-802.11n wireless devices.
20MHz - Select if you are not using any 802.11n wireless
clients.
Security Mode: Select WEP or WPA Personal. Refer to page 22.
D-Link DAP-1320 User Manual
21
Section 3 - Configuration
Wireless Security
This section will show you the different levels of security you can use to protect your data from intruders. The DAP-1320 offers
the following types of security:
• WPA2 (Wi-Fi Protected Access 2) • WPA (Wi-Fi Protected Access)
• WEP (Wired Equivalent Privacy)
• WPA2-PSK (Pre-Shared Key)
• WPA-PSK (Pre-Shared Key)
What is WPA?
WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent
Privacy).
The 2 major improvements over WEP:
• Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a
hashing algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered
with. WPA2 is based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP.
• User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP).
WEP regulates access to a wireless network based on a computer’s hardware-specific MAC address, which is
relatively simple to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to
ensure that only authorized network users can access the network.
WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password
between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key
entered on your wireless router or access point.
WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more
secure public key encryption system to ensure that only authorized network users can access the network.
D-Link DAP-1320 User Manual
22
Section 3 - Configuration
Configure WPA/WPA2 Personal
It is recommended to enable wireless security on your DAP-1320 before your wireless clients. Please establish wireless
connectivity before enabling. Your wireless signal may degrade when enabling encryption due to the added overhead.
1. Log into the web-based configuration by opening a web browser
and entering http://dlinkap.local. Click Setup and then click
Wireless Settings on the left side.
2.Next to Security Mode, select WPA-Personal.
3.Next to Pre-Shared Key, enter a key (Wi-Fi password). The Wi-Fi
password must be between 8-63 characters and is case-sensitive.
4.Click Save Settings at the top of the window to save your
settings. You will lose connectivity until you enable WPA-PSK
on the device you are working from and enter the same Wi-Fi
password as you did on the DAP-1320.
D-Link DAP-1320 User Manual
23
Section 3 - Configuration
Maintenance
Admin
This page will allow you to change the Administrator password.
Password: Enter a new password for the Admin login name. The
administrator can make changes to the settings.
Confirm Enter the same password that you entered in the previous
Password: textbox in order to confirm its accuracy.
Enable Checking this box enables a challenge-response test to
Graphical require users to type letters or numbers from a distorted
Authentication: image displayed on the screen. This prevents online hackers
and unauthorized users from gaining access to your network
settings on your DAP-1320.
D-Link DAP-1320 User Manual
24
Section 3 - Configuration
System
Save to Local Use this option to save the current DAP-1320 configuration
Hard Drive: settings to a file on the hard disk of the computer you are
using. Click the Save button. You will then see a file dialog
where you can select a location and file name for the settings.
Upload from Use this option to load previously saved DAP-1320
Local Hard Drive: configuration settings. Click Browse to find a previously
saved configuration file. Then, click the Upload Settings
button to transfer those settings to the DAP-1320.
Restore to This option will restore the DAP-1320 back to the factory
Factory Default: default settings.
Reboot the
Device: Click to reboot the DAP-1320.
D-Link DAP-1320 User Manual
25
Section 3 - Configuration
Firmware
You can upgrade the firmware of the DAP-1320 here. Make sure the firmware you want to use is on the local hard drive of the
computer. Please check the D-Link support website for firmware updates at http://support.dlink.com. You can download
firmware upgrades to your computer from this site.
Firmware Click on Check Now to find out if there is an updated
Upgrade: firmware; if so, download the new firmware to your
computer.
Browse: After you have downloaded the new firmware, click
Browse to locate the firmware update on your hard
drive. Click Upload to complete the firmware upgrade.
Upload: Once you have a firmware update on your computer,
click Upload and begin the firmware upgrade
Language Pack
You can change the language of the web UI by uploading
available language packs.
Browse: After you have downloaded the new language pack,
click Browse to locate the language pack file on your
computer. Click Upload to complete the language
pack upgrade.
D-Link DAP-1320 User Manual
26
Section 3 - Configuration
Time
The Time Configuration page allows you to configure, update, and maintain the correct time on the internal system clock.
From this section you can set the time zone that you are in. Daylight Saving can also be configured to automatically adjust the
time when needed.
Time Zone: Select your Time Zone from the drop-down menu.
Enable To select Daylight Saving time manually, click the Enable
Daylight Daylight Saving check box. Next use the drop-down menu
Saving: to select a Daylight Saving Offset and then enter a start date
and an end date for daylight saving time.
Enable NTP NTP is short for Network Time Protocol. Check this box to
Server: use a NTP server. This will only connect to a server on the
Internet, not a local server.
NTP Server
Used: Enter the NTP server or select one from the drop-down menu.
Date and Time: To manually input the time, enter the values in these fields
for the Year, Month, Day, Hour, Minute, and Second and
then click Save Settings. You can also click the Copy Your
Computer’s Time Settings button at the bottom of the
screen to use your computer’s settings.
D-Link DAP-1320 User Manual
27
Section 3 - Configuration
Status
Device Info
This page displays the current information for the DAP-1320. It will display the Wi-Fi network and Extended Wi-Fi Network
information.
General: Displays the access point’s time and firmware version.
Wi-Fi Network: Displays the MAC address and the private (local) IP settings
for the access point.
Extended Wi-Fi Displays the wireless MAC address and your wireless settings
Network: such as SSID, Channel, and IP Settings.
D-Link DAP-1320 User Manual
28
Section 3 - Configuration
Logs
The DAP-1320 keeps a running log of events and activities. If the device is rebooted, the logs are automatically cleared. You
can save the log files by clicking the Save Log button.
Log Options: There are several types of logs that can be viewed: System
Activity, Debug Information, Attacks, Dropped Packets
and Notice. Check the Log Options you want to view and
click Apply Log Settings Now.
First Page: This button directs you to the first page of the log.
Last Page: This button directs you to the last page of the log.
Previous: This button directs you to the previous page of the log.
Next: This button directs you to the next page of the log.
Clear: This button clears all current log content.
Save Log: Click to Save the log to your computer.
Refresh: This button refreshes the log.
D-Link DAP-1320 User Manual
29
Section 3 - Configuration
Statistics
The DAP-1320 keeps statistics of wireless traffic that passes through it. The wireless statistics will reset if the DAP-1320 is rebooted.
D-Link DAP-1320 User Manual
30
Section 3 - Configuration
IPv6
This page displays all your IPv6 connection information.
D-Link DAP-1320 User Manual
31
Section 4 - Connecting to a Wireless Network
WPS
From Client to DAP-1320
The easiest and most secure way to connect your wireless devices to the DAP-1320 is WPS (Wi-Fi Protected Setup). Most
wireless devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers and cameras will have a WPS
button (or a software utility with WPS) that you can press to connect to the DAP-1320. Please refer to your user manual for
the wireless device you want to connect to make sure you understand how to enable WPS. Once you know, follow the steps
below:
Step 1 - Press and release the WPS button on the DAP- 1320. The LED
will blink green during the WPS process.
Step 2 -Within two minutes, press the WPS button on your wireless
client (or launch the software utility and start the WPS
process).
Step 3 - Allow up to two minutes to connect. Once the connection is
successful the LED will be solid green.
D-Link DAP-1320 User Manual
32
Section 4 - Connecting to a Wireless Network
Windows® 7
WPA/WPA2
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your
wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
1.Click on the wireless icon in your system tray (lower-right corner).
Wireless Icon
2.The utility will display any available wireless networks in your area.
D-Link DAP-1320 User Manual
33
Section 4 - Connecting to a Wireless Network
3.Highlight the wireless network (SSID) you would like to connect to
and click the Connect button.
If you get a good signal but cannot access the Internet, check your
TCP/IP settings for your wireless adapter. Refer to the Networking
Basics section in this manual for more information.
Note: You can find the SSID and password on the configuration card.
4. The following window appears while your computer tries to connect
to the router.
D-Link DAP-1320 User Manual
34
Section 4 - Connecting to a Wireless Network
5.Enter the security key or passphrase that is on your configuration
card and click Connect. You can also connect by pushing the WPS
button on the DAP-1320.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the security settings are correct. The
key or passphrase must be exactly the same as on the wireless router.
D-Link DAP-1320 User Manual
35
Section 4 - Connecting to a Wireless Network
Windows Vista®
Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility or Windows® 2000, please
refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site
survey” option similar to the Windows Vista® utility as seen below.
If you receive the Wireless Networks Detected bubble, click on the
center of the bubble to access the utility.
or
Right-click on the wireless computer icon in your system tray (lower-right
corner next to the time). Select Connect to a network.
The utility will display any available wireless networks in your area. Click
on a network (displayed using the SSID) and click the Connect button.
If you get a good signal but cannot access the Internet, check you TCP/
IP settings for your wireless adapter. Refer to the Networking Basics
section in this manual for more information.
D-Link DAP-1320 User Manual
36
Section 4 - Connecting to a Wireless Network
WPA/WPA2
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your
wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
1. Open the Windows Vista® Wireless Utility by right-clicking on the
wireless computer icon in your system tray (lower right corner of
screen). Select Connect to a network.
2. Highlight the wireless network (SSID) you would like to connect
to and click Connect.
D-Link DAP-1320 User Manual
37
Section 4 - Connecting to a Wireless Network
3. Enter the same security key or passphrase that is on your router and
click Connect.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the security settings are correct. The
key or passphrase must be exactly the same as on the wireless router.
D-Link DAP-1320 User Manual
38
Section 4 - Connecting to a Wireless Network
WPS/WCN 2.0
The router supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista®. The following instructions for setting this up
depends on whether you are using Windows Vista® to configure the router or third party software.
When you first set up the router, Wi-Fi protection is disabled and unconfigured. To enjoy the benefits of Wi-Fi protection, the
router must be both enabled and configured. There are three basic methods to accomplish this: use Windows Vista’s built-in
support for WCN 2.0, use software provided by a third party, or manually configure.
If you are running Windows Vista®, log into the router and click the Enable checkbox in the Basic > Wireless section. Use the
Current PIN that is displayed on the Advanced > Wi-Fi Protected Setup section or choose to click the Generate New PIN
button or Reset PIN to Default button.
If you are using third party software to set up Wi-Fi Protection, carefully follow the directions. When you are finished, proceed
to the next section to set up the newly-configured router.
D-Link DAP-1320 User Manual
39
Section 4 - Connecting to a Wireless Network
Windows® XP
Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service
Pack 2 users. If you are using another company’s utility, please refer to the user manual of your wireless adapter for help with
connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
If you receive the Wireless Networks Detected bubble, click on the
center of the bubble to access the utility.
or
Right-click on the wireless computer icon in your system tray (lower-right
corner next to the time). Select View Available Wireless Networks.
The utility will display any available wireless networks in your area. Click
on a network (displayed using the SSID) and click the Connect button.
If you get a good signal but cannot access the Internet, check you TCP/
IP settings for your wireless adapter. Refer to the Networking Basics
section in this manual for more information.
D-Link DAP-1320 User Manual
40
Section 4 - Connecting to a Wireless Network
WPA/WPA2
It is recommended to enable WPA on your wireless router or access point before configuring your wireless adapter. If you are
joining an existing network, you will need to know the WPA key being used.
1. Open the Windows® XP Wireless Utility by right-clicking on the
wireless computer icon in your system tray (lower-right corner
of screen). Select View Available Wireless Networks.
2. Highlight the wireless network (SSID) you would like to
connect to and click Connect.
D-Link DAP-1320 User Manual
41
Section 4 - Connecting to a Wireless Network
3.The Wireless Network Connection box will appear. Enter the WPA-PSK
passphrase and click Connect.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the WPA-PSK settings are correct. The
WPA-PSK passphrase must be exactly the same as on the wireless router.
D-Link DAP-1320 User Manual
42
Section 5 - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DAP-1320. Read the
following descriptions if you are having problems. The examples below are illustrated in Windows® XP. If you have a different
operating system, the screenshots on your computer will look similar to the following examples.
1. Why can’t I access the web-based configuration utility?
When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website nor do you
have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must
be on the same IP subnet to connect to the web-based utility.
• Make sure you have an updated Java-enabled web browser. We recommend the following:
-Microsoft Internet Explorer® 7 and higher
-Mozilla Firefox
-Google™ Chrome
-Apple Safari 4 and higher
• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a
different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may not be
on.
• Disable any Internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice, Sygate,
Norton Personal Firewall, and Windows® XP firewall may block access to the configuration pages. Check the help files included
with your firewall software for more information on disabling or configuring it.
D-Link DAP-1320 User Manual
43
Section 5 - Troubleshooting
• Configure your Internet settings:
• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click
the button to restore the settings to their defaults.
• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button.
Make sure nothing is checked. Click OK.
• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
• Close your web browser (if open) and open it.
• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This
should open the login page for your web management.
• If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait about 30
seconds and try accessing the configuration. If you have multiple computers, try connecting using a different computer.
2. What can I do if I forgot my password?
If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the
factory defaults.
To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip
to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30
seconds to access the router. The default IP address is 192.168.0.50. When logging in, the username is admin and leave the
password box empty.
D-Link DAP-1320 User Manual
44
Appendix A - Wireless Basics
Wireless Basics
D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless
connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link
wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able
to enjoy the freedom that wireless networking delivers.
A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of
wires. Wireless LANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops
and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently.
Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users.
Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop
systems support the same protocols as Ethernet adapter cards.
Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to
use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide
this link.
D-Link DAP-1320 User Manual
45
Appendix A - Wireless Basics
What is Wireless?
Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio
frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network.
Why D-Link Wireless?
D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link
delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network.
How does wireless work?
Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But
wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area
to be able to connect your computer. There are two different types of wireless networks Wireless Local Area Network (WLAN),
and Wireless Personal Area Network (WPAN).
Wireless Local Area Network (WLAN)
In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has
a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point
as seen in the picture, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles
to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and
many other outdoor venues.
D-Link DAP-1320 User Manual
46
Appendix A - Wireless Basics
Wireless Personal Area Network (WPAN)
Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to
30 feet away.
Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as
much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other
devices that operate on batteries.
Who uses wireless?
Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, office, business,
D-Link has a wireless solution for it.
Home
• Gives everyone at home broadband access
• Surf the web, check email, instant message, etc.
• Gets rid of the cables around the house
• Simple and easy to use
Small Office and Home Office
• Stay on top of everything at home as you would at office
• Remotely access your office network from home
• Share Internet connection and printer with multiple computers
• No need to dedicate office space
D-Link DAP-1320 User Manual
47
Appendix A - Wireless Basics
Where is wireless used?
Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming
so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public
places is usually called “hotspots”.
Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations
like: Airports, Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers.
Wireless network is easy to setup, but if you’re installing it for the first time it could be quite a task not knowing where to start.
That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.
Tips
Here are a few things to keep in mind, when you install a wireless network.
Centralize your router or Access Point
Make sure you place the router/access point in a centralized location within your network for the best performance. Try to
place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have
a two-story home, you may need a repeater to boost the signal to extend the range.
Eliminate Interference
Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access
point. This would significantly reduce any interference that the appliances might cause since they operate on same frequency.
Security
Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on
the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up.
D-Link DAP-1320 User Manual
48
Appendix B - Networking Basics
Networking Basics
Check your IP address
After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP
server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.
Click on Start > Run. In the run box type cmd and click OK. (Windows® 7/Vista® users type cmd in the Start Search box.)
At the prompt, type ipconfig and press Enter.
This will display the IP address, subnet mask, and the default
gateway of your adapter.
If the address is 0.0.0.0, check your adapter installation,
security settings, and the settings on your router. Some
firewall software programs may block a DHCP request on
newly installed adapters.
D-Link DAP-1320 User Manual
49
Appendix B - Networking Basics
Statically Assign an IP address
If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:
Step 1
Windows® 7 -
Click on Start > Control Panel > Network and Internet > Network and Sharing Center.
Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network
Connections.
Windows® XP - Click on Start > Control Panel > Network Connections.
Windows® 2000 - From the desktop, right-click My Network Places > Properties.
Step 2
Right-click on the Local Area Connection which represents your network adapter and select Properties.
Step 3
Highlight Internet Protocol (TCP/IP) and click Properties.
Step 4
Click Use the following IP address and enter an IP address that is on the same subnet
as your network or the LAN IP address on your router.
Example: If the router´s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X
where X is a number between 2 and 99. Make sure that the number you choose is not
in use on the network. Set the Default Gateway the same as the LAN IP address of your
router (I.E. 192.168.0.1).
Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The
Secondary DNS is not needed or you may enter a DNS server from your ISP.
Step 5
Click OK twice to save your settings.
D-Link DAP-1320 User Manual
50
Appendix C - Technical Specifications
Technical Specifications
Standards
• IEEE 802.11n
• IEEE 802.11g
• IEEE 802.3
Certifications
• Wi-Fi Certified
• FCC
Wireless Frequency Range
• 2.4 GHz to 2.4835 GHz
Dimensions
• 2.11” x 1.65” x 1.89’’ (53.5 x 42 x 48mm)
Antennas
• Internal Antenna
Weight
• 2.56 oz. (72.57g)
Security
• Wi-Fi Protected Access (WPA/WPA2)
• WPS™ (PBC)
Warranty
• 1-Year Limited Warranty
Advanced Features
• Quick Router Setup app for iOS
Device Management
• Web UI
Diagnostic LEDs
• Power/ Status
Operating Temperature
• 32 to 104 ˚F (0 to 40 ˚C)
Operating Humidity
• 0% to 90% non-condensing
1 Maximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume
of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely affect wireless signal range.
2 Frequency Range varies depending on country’s regulation
D-Link DAP-1320 User Manual
51
Appendix D - Contacting Technical Support
Contacting Technical Support
U.S. and Canadian customers can contact D-Link technical support through our web site or by phone.
Before you contact technical support, please have the following ready:
• Model number of the product (e.g. DAP-1320)
• Hardware Revision (located on the label on the bottom of the router (e.g. rev A1))
• Serial Number (s/n number located on the label on the bottom of the router).
You can find software updates and user documentation on the D-Link website as well as frequently asked questions and
answers to technical issues.
For customers within the United States:
Phone Support:
(877) 453-5465
For customers within Canada:
Internet Support:
http://support.dlink.com
Phone Support:
(800) 361-5265
Internet Support:
http://support.dlink.ca
D-Link DAP-1320 User Manual
52
Appendix F - Warranty
Warranty
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty:
• Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and
• Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions
or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Limited Warranty:
D-Link warrants that the hardware portion of the D-Link product described below (“Hardware”) will be free from material defects in workmanship
and materials under normal use from the date of original retail purchase of the product, for the period set forth below (“Warranty Period”), except
as otherwise stated herein.
• Hardware (excluding power supplies and fans): One (1) year
• Power supplies and fans: One (1) year
• Spare parts and spare kits: Ninety (90) days
The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at
D-Link’s option, to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual
purchase price paid. Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement hardware
need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any
reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware.
Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety (90) days, whichever is longer,
and is subject to the same limitations and exclusions. If a material defect is incapable of correction, or if D-Link determines that it is not practical
to repair or replace the defective Hardware, the actual price paid by the original purchaser for the defective Hardware will be refunded by D-Link
upon return to D-Link of the defective Hardware. All Hardware or part thereof that is replaced by D-Link, or for which the purchase price is refunded,
shall become the property of D-Link upon replacement or refund.
D-Link DAP-1320 User Manual
53
Appendix F - Warranty
Limited Software Warranty:
D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications
for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90)
days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its
documentation. D-Link further warrants that, during the Software Warranty Period, the magnetic media on which D-Link delivers the Software will be
free of physical defects. The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will
be, at D-Link’s option, to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s functional
specifications for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except as otherwise
agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the
license granted by D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is subject
to the same limitations and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it
is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by
D-Link; provided that the non-conforming Software (and all copies thereof ) is first returned to D-Link. The license granted respecting any Software
for which a refund is given automatically terminates.
Non-Applicability of Warranty:
The Limited Warranty provided hereunder for Hardware and Software portions of D-Link’s products will not be applied to and does not cover any
refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or
the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold “As-Is” without any
warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the contrary.
Submitting A Claim (USA):
The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and
the product is within warranty, the customer shall submit a claim to D-Link as outlined below:
• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software
nonconformance in sufficient detail to allow DLink to confirm the same, along with proof of purchase of the product (such as a
copy of the dated purchase invoice for the product) if the product is not registered.
• The customer must obtain a Case ID Number from D-Link Technical Support at 1-877-453-5465, who will attempt to assist the
customer in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a
Return Material Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https://
rma.dlink.com/.
D-Link DAP-1320 User Manual
54
Appendix F - Warranty
• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package
to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package.
Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product
and will not ship back any accessories.
• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD
will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped
to D-Link Systems, Inc., 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that
are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common
carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in the United States, otherwise
we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are
prepaid by the customer. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the
foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to
pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance
with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.
Submitting A Claim (Canada):
The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and
the product is within warranty, the customer shall submit a claim to D-Link as outlined below:
• Customers need to provide their receipt (proof of purchase) even if the product is registered. Without a receipt, no warranty service will
be done. The registration is not considered a proof of purchase.
• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance
in sufficient detail to allow D-Link to confirm the same, along with proof of purchase of the product (such as a copy of the dated purchase
invoice for the product) if the product is not registered.
• The customer must obtain a Case ID Number from D-Link Technical Support at 1-800-361-5265, who will attempt to assist the customer
in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a Return Material
Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https://rma.dlink.ca/.
• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to
ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not
include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship
back any accessories.
D-Link DAP-1320 User Manual
55
Appendix F - Warranty
• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will
be rejected by D-Link. Products shall be fully insured by the customer and shipped to D-Link Networks, Inc., 2525 Meadowvale Boulevard
Mississauga, Ontario, L5N 5S2 Canada. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired
or replaced packages will be shipped to the customer via Purolator Canada or any common carrier selected by D-Link. Return shipping
charges shall be prepaid by D-Link if you use an address in Canada, otherwise we will ship the product to you freight collect. Expedited
shipping is available upon request and provided shipping charges are prepaid by the customer. D-Link may reject or return any product
that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from
the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product
that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or
non-conforming.
• RMA phone number: 1-800-361-5265 Hours of Operation: Monday-Friday, 9:00AM – 9:00PM EST
What Is Not Covered:
The Limited Warranty provided herein by D-Link does not cover:
Products that, in D-Link’s judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation,
lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number
has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs;
Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act
of God, failures due to power surge, and cosmetic damage; Any hardware, software, firmware or other products or services provided by anyone
other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers,
or the liquidators expressly disclaim their warranty obligation pertaining to the product.
While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link
Service Office. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.
Disclaimer of Other Warranties:
EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER
INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY
SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE
LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE
PURCHASER OF THE PRODUCT.
D-Link DAP-1320 User Manual
56
Appendix F - Warranty
Limitation of Liability:
TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL
OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK
STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT
IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK
FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF
THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF
THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT. THE MAXIMUM
LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING
EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED
OR STATUTORY.
Governing Law:
This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This
Limited Warranty provides specific legal rights and you may also have other rights which vary from state to state.
Trademarks:
D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their
respective owners.
Copyright Statement:
No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the
United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.
Copyright ©2012 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.
CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take
adequate measures.
D-Link DAP-1320 User Manual
57
Appendix F - Warranty
FCC Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US
must fixed to US operation channels only.
IMPORTANT NOTICE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.to match the intended destination. The firmware setting is not accessible
by the end user.
D-Link DAP-1320 User Manual
58
Appendix F - Warranty
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet
aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu,
y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
Declaration d’exposition aux radiations:
Cet equipement est conforme aux limites d’exposition aux rayonnements IC etablies pour un environnement non controle. Cet equipement doit
etre installe et utilise avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
D-Link DAP-1320 User Manual
59
Appendix G - Registration
Registration
Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.
Version 1.0
September 5, 2012
D-Link DAP-1320 User Manual
60