Dell™ S320/S320wi Projector
User’s Guide
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you
make better use of your projector
CAUTION: A CAUTION indicates potential damage to hardware
or loss of data if instructions are not followed.
WARNING: A WARNING indicates a potential for property
damage, personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2012 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written
permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of
Dell Inc.; DLP and DLP logo are trademarks of TEXAS INSTRUMENTS
INCORPORATED; Microsoft and Windows are either trademarks or registered
trademarks of Microsoft Corporation in the United States and/or other countries.
Other trademarks and trade names may be used in this document to refer to either
the entities claiming the marks and names or their products. Dell Inc. disclaims
any proprietary interest in trademarks and trade names other than its own.
Model S320/S320wi
September 2012
Rev. A00
Contents
1
Your Dell Projector .
. . . . . . . . . . . . . . . . .
About Your Projector
. . . . . . . . . . . . . . . .
About Your Interactive Pen
2
. . . . . . . . . . . . .
Connecting Your Projector .
. . . . . . . . . . .
Installing the Optional Wireless Module Kit
. . . .
Installing the Optional Interactive Module Kit
10
11
13
14
. . .
15
. . . . . . . . . . .
16
. . . . . . . . . . . . . . . .
17
Installing the Optional RJ45 Kit
Connecting to a Computer
7
Connecting a Computer Using a VGA Cable
. . . .
17
Monitor Loop-Through Connection Using VGA Cables . . . . . . . . . . . . . . . . .
. . . .
18
. . .
19
. . . . . . .
20
. . . . . . . . . .
21
. . . . . . . . . . . . . . . .
22
Connecting a Computer Using a RS232 cable
Connecting a Computer by USB Cable
Connecting a Computer Using Wireless Dongle (Optional) . . .
Connecting a DVD Player
.
22
Connecting a DVD Player Using a Composite Video Cable . . . . . .
. . . . . . . . .
23
Connecting a DVD Player Using a Component Video Cable . . . . .
. . . . . . . . .
24
Connecting a DVD Player Using an S-Video Cable
. .
25
. . . . . . . . . . .
26
Connecting a DVD Player Using a HDMI Cable
Connecting to Local Area Network
To project an image and control the projector that is connected to a network through a RJ45 cable. . . 26
Contents
3
Connection With Commercial RS232 Control Box
.
27
. . . . . . .
28
Using Your Projector
. . . . . . . . . . . . . . . .
30
Turning Your Projector On
. . . . . . . . . . . . . . . .
30
Connecting With Your Interactive Pen
3
Turning Your Projector Off .
. . . . . . . . . . . . . . .
Adjusting the Projected Image
. . . . . . . . . . . . .
Raising the Projector Height
. . . . . . . . . . . .
Lowering the Projector Height
Adjusting the Projector Focus .
31
31
. . . . . . . . . . . . .
32
. . . . . . . . . . . .
33
. . . . . . . . . . . . . . . . .
35
Using the Remote Control
. . . . . . . . . . . . . . . .
37
Using the Interactive Pen
. . . . . . . . . . . . . . . .
40
. . . . . . .
41
. . . . . . . . . . . . . .
41
. . . . . . . . . . . . . . . . . .
42
OSD warning messages - low battery
Combinations of buttons
Using the Wrist Strap
Installing the Remote Control Batteries
Charging the Interactive Pen Battery
. . . . . . . .
43
. . . . . . . . . .
44
Docking Charger Introduction (Optional)
. . . . . . . .
Charging the Interactive Pen Battery by Docking Charger . . . . . . . . . . . . . .
45
. . . . . . .
47
Operating Range with Remote Control
. . . . . . . . .
49
Operating Range with Interactive Pen
. . . . . . . . .
50
. . . . . . . . . . . . . .
51
. . . . . . . . . . . . . . . . . . .
51
Using the On-Screen Display
INPUT SOURCE
4
31
. . . . . . . . . . .
Adjusting Projection Image Size
Using the Control Panel
30
Contents
AUTO ADJUST
. . . . . . . . . . . . . . . . . . .
BRIGHTNESS/CONTRAST
53
. . . . . . . . . . . . . . . . . . . .
53
. . . . . . . . . . . . . . . . . . . . . .
54
VIDEO MODE
VOLUME .
AUDIO INPUT
. . . . . . . . . . . . . . . . . . . .
ADVANCED SETTINGS
54
. . . . . . . . . . . . . . .
55
. . . . . . . . . . . . . . . . . . . . .
72
. . . . . . . . . . . . . . . . . . . . . . . .
73
LANGUAGE
HELP .
52
. . . . . . . . . . . . .
Wireless Networking Installation
. . . . . . . . . . . .
Enable Wireless on the Projector .
. . . . . . . . .
Install the Wireless Application Software on
Your Computer . . . . . . . . . . . . . . . .
75
. . .
76
. . . . . . . . . .
80
. . . . . . . . . .
83
. . . . . . . . . . . . . . . . . . . . .
84
Launch the Wireless Application
Presentation to Go (PtG) Installation
PtG Viewer
74
Photo Viewer
. . . . . . . . . . . . . . . . . . . .
PtG/Photo Function Introduction
PtG Overview
84
. . . . . . . . . .
85
. . . . . . . . . . . . . . . . . . . .
85
Photo Overview
. . . . . . . . . . . . . . . . . . .
Buttons Introduction
. . . . . . . . . . . . . . . .
86
86
Install the PtG Converter Application Software on Your Computer . . . . . . . . . . . . . . . . . . . 87
Using the PtG Converter
. . . . . . . . . . . . . .
87
Audio Projection Installation
. . . . . . . . . . . . . .
89
Enable Wireless or LAN on the Projector
. . . . .
Install the Wireless Application Software on
Your Computer . . . . . . . . . . . . . . . .
. . .
92
. . . . . . . . . .
93
. . . . . . . . . . . . . . . . . . . . . . . .
94
Launch the Wireless Application
Login
91
Managing the Projector From Web Management (for Wireless Network) . . . . . . . . . . . . . .
. . .
Contents
95
5
Configuring the Network Setting
Accessing Web Management
. . . . . . . . . .
95
. . . . . . . . . . .
95
Managing the Projector From Web Management (Network RJ45 Kit is Optional for S320) . . . . . .
. . . . . . . . . .
110
110
. . . . . . . . . . . . . . . .
111
. . . . . . . . . . . . . . . .
125
Accessing Web Management
Make Application Token
4
Troubleshooting Your Projector
Troubleshooting your Interactive Pen .
Guiding Signals
6
Contacting Dell
. . . . . . . . . . . . . . . . . . . . .
132
. . . . . . . . . .
133
. . . . . . . . . . . . . . . . . . .
134
. . . . . . . . . . . . . . . . . . . .
136
. . . . . . . . . . . . . . . . . . .
144
Contacting eInstruction
Contacting Crestron
7
6
. . . . . . . . . . . . . . . . .
145
. . . . . . . . . . . . . . . . . . .
146
Appendix: Glossary
Contents
126
130
Changing the Lamp
Specifications
. . . . . .
. . . . . . . . .
Interactive Pen LED Guiding Signals
5
110
. . . . . . . . . . .
Configuring the Network Setting
Managing Properties
. . .
. . . . . . . . . . . . . . . .
147
1
Your Dell Projector
Your projector comes with all the items shown below. Ensure that you have all the
items, and contact Dell if anything is missing.
S320 Standard Package Contents
Power cable
1.8 m VGA cable (VGA to VGA)
AAA Batteries (2)
Remote control
POWER
A
A
ENTER
A
A
MENU
A
SOURCE
ASPECT
VOL
VIDEO MODE
A
MUTE
KEYSTONE
VOL
AUTO ADJ. FREEZE
CD User’s Guide and Documentation
MOUSE
BLANK
ZOOM
ZOOM
INFO
VGA
VIDEO
S-VIDEO
Dell Interactive wireless dongle
(Optional)
Informacion Importante
tor
320wi Projec
Dell S320/S Setup Guide
Quick
TM
Dell
Pro
TM
DOCOMENTATION
Dell S320/S320wi
Projector
TM
oduc
t Info
jector
rmat
ion
s
Guide
DPB2701
Your Dell Projector
7
S320wi Standard Package Contents
Power cable
1.8 m VGA cable (VGA to VGA)
AAA Batteries (2)
Remote control
POWER
A
A
ENTER
A
A
MENU
A
SOURCE
ASPECT
VOL
VIDEO MODE
A
MUTE
KEYSTONE
VOL
AUTO ADJ. FREEZE
CD User’s Guide and Documentation
MOUSE
BLANK
ZOOM
ZOOM
INFO
VGA
VIDEO
S-VIDEO
Interactive Pen
Informacion Importante
tor
320wi Projec
Dell S320/S Setup Guide
Quick
TM
Dell
oduc
TM
Pro
t Info
DOCOMENTATION
jector
rmat
Dell S320/S320wi
Projector
TM
ion
s
Guide
Nib (10 spare pen nib)
Interwrite Workspace CD
2 m Mini USB cable (USB-A to Mini
USB-B)
©
19
99
-2
01
Wrist strap
8
1
Corporation. All rights
ction
rese
stru
rve
eIn
d. 1
oration. All rights reserve 011
1-0
Corp
-2d
tion
07
99 . 11-00
98
truc
19
798
©
Ins
Re
Re
rights reserved. 1111-0e07
vE
vE
98 R
n. All
0
ev E
ratio
-2
rpo
99
Co
19
on
©
cti
tru
TM
ns
TM
eI
WorkSpace
ce
ceorkSpa
paW
rkS
o
W
TM
Your Dell Projector
S320wi Standard Package Contents
5 m Mini USB cable (USB-A to Mini
USB-B)
USB cable (USB-A to USB-B)
Dell Interactive wireless dongle
(Optional)
DPB2701
Your Dell Projector
9
About Your Projector
Top View
Bottom View
10
7
26.0±0.1
14.0±0.1
9
1
82.30±0.15
5
4
3
2
110.00±0.15
6
10
8
1
Control panel
2
5W speaker
3
Focus ring
4
Lens
5
IR receivers
6
Lens cap
7
Lamp cover
8
Mounting holes for wall mount: Screw hole M3 x 6.5 mm depth.
Recommended torque <8 kgf-cm
9
Mounting hole for tripod: Insert nut 1/4"*20 UNC
10
Tilt adjustment wheel
10
Your Dell Projector
About Your Interactive Pen
Top View
Bottom View
4
5
3
6
7
2
8
1
1
Replaceable nib
2
Lens
3
Control buttons
4
LED indicators
5
Wrist strap holder
6
Power switch
7
Firmware upgrade connector
8
Mini USB charge connector
NOTE: Optional (can be bought separately), or comes with S320wi only.
CAUTION: Safety Instructions
1 Do not use the projector near appliances that generate a lot of heat.
2 Do not use the projector in areas where there is an excessive amount of dust.
The dust may cause the system to fail and the projector will automatically
shutdown.
3 Ensure that the projector is mounted in a well-ventilated area.
4 Do not block the ventilation slots and openings on the projector.
5 Ensure the projector operates between ambient temperatures (5 ºC to 35 ºC).
6 Do not try to touch the ventilation outlet as it can become very hot after the
projector has been turned on or immediately after it is turned off.
7 Do not look into the lens while the projector is on as it may cause injury to your
eyes.
Your Dell Projector
11
8 Do not place any objects near or in front of the projector or cover its lens while
the projector is on as the heat may cause the object to melt or burn.
9 Do not use the wireless projector near cardiac pacemakers.
10 Do not use the wireless projector near medical equipment.
11 Do not use the wireless projector near microwave ovens.
NOTE:
• Do not attempt to wall mount the projector by yourself. It should be
installed by a qualified technician.
• Recommended Projector Wall Mount Kit (P/N: 4TVT8/V3RTH). For
more information, see the Dell Support website at support.dell.com.
• For more information, see the Safety Information that shipped with your
projector.
• The S320/S320wi projector can only be used indoors.
12
Your Dell Projector
Connecting Your Projector
1
VGA-OUT
2
3
4
VGA-A IN
VGA-B IN
HDMI
Audio-In
15
Audio-Out
Composite
14 13 12
S-Video
5
6
USB-A
DOUSB
2
7
RJ45
RS232
Mini-USB
11 10 9
8
1
VGA output (monitor loop
through) connector
9
Security cable slot
2
VGA-A input (D-sub) connector
10
Mini USB (Mini Type B)
connector for remote mouse,
Interactive function, and
firmware upgrade
3
VGA-B input (D-sub) connector
11
S-Video connector
4
HDMI connector
12
Composite Video connector
5
USB Type A connector for USB
Viewer (embedded for S320wi)
13
Audio output connector
6
USB Type B connector for USB
Display (embedded for S320wi)
14
Audio input connector
7
RJ45 connector (embedded for
S320wi)
15
Power cord connector
8
RS232 connector
CAUTION: Before you begin any of the procedures in this section, follow the
Safety Instructions as described on page 11.
Connecting Your Projector
13
Installing the Optional Wireless Module Kit
Your projector must be installed with the wireless module kit if you want
to use the wireless networking option. Refer to "Wireless Networking
Installation" on page 74. The wireless module kit is not shipped with your
S320 projector. You can purchase it on the Dell website at www.dell.com.
NOTE: Wireless module kit embedded for S320wi.
The installation steps are as below:
1
2
3
4
14
Connecting Your Projector
Installing the Optional Interactive Module Kit
Your projector must be installed with Interactive module kit if you want to
use the Interactive feature. The Interactive module kit is not shipped with
your S320 projector. You can purchase it on the Dell website at
www.dell.com.
NOTE: Interactive module kit embedded for S320wi.
The installation steps are as below:
1
2
3
4
Connecting Your Projector
15
Installing the Optional RJ45 Kit
Your projector must be installed with RJ45 kit if you want to use the
network option. The RJ45 kit is not shipped with your S320 projector. You
can purchase it on the Dell website at www.dell.com.
NOTE: RJ45 is embedded in the S320wi.
The installation steps are as below:
1
2
3
4
16
Connecting Your Projector
Connecting to a Computer
Connecting a Computer Using a VGA Cable
VGA-OUT
VGA-A IN
VGA-B IN
HDMI
USB-A
Audio-In
1
Audio-Out
Composite
S-Video
DOUSB
2
RJ45
RS232
Mini-USB
3
MOLEX
1
Power cord
2
VGA to VGA cable
3
USB-A to Mini USB-B cable
NOTE: The Mini USB cable must be connected if you want to use the Page Up
and Page Down features on the remote control.
Connecting Your Projector
17
Monitor Loop-Through Connection Using VGA Cables
VGA-OUT
VGA-A IN
VGA-B IN
HDMI
USB-A
Audio-In
1
2
1
Power cord
2
VGA to VGA cable
Audio-Out
Composite
S-Video
Mini-USB
DOUSB
RJ45
RS232
2
NOTE: Only one VGA cable is shipped with your projector. An additional VGA
cable can be purchased on the Dell website at www.dell.com.
18
Connecting Your Projector
Connecting a Computer Using a RS232 cable
VGA-OUT
VGA-A IN
VGA-B IN
HDMI
USB-A
Audio-In
Audio-Out
Composite
S-Video
Mini-USB
1
1
Power cord
2
RS232 (9-pin D-sub female to female
pin2-3 swap) cable
DOUSB
RJ45
RS232
2
NOTE: The RS232 (9-pin D-sub female to female pin2-3 swap) cable is not
shipped with your projector. Consult a professional installer for the cable and
RS232 remote control software.
Connecting Your Projector
19
Connecting a Computer by USB Cable
VGA-OUT
VGA-A IN
VGA-B IN
HDMI
USB-A
Audio-In
Audio-Out
Composite
S-Video
DOUSB
RJ45
RS232
Mini-USB
1
2
MOLEX
1
Power cord
2
USB-A to USB-B cable
NOTE: Plug and Play. Only one USB cable is shipped with your projector. An
additional USB cable can be purchased on the Dell website at www.dell.com.
20
Connecting Your Projector
Connecting a Computer Using Wireless Dongle (Optional)
NOTE: A USB wireless dongle is embedded in the Dell S320wi.
NOTE: Wireless functionality is an optional feature on the Dell S320. If you
would like to include wireless functionality, please install a wireless module
and a USB wireless dongle into your Dell S320. See step-by-step installation
guide on page 13. Wireless modules and USB wireless dongles are available
and sold separately on www.dell.com.
NOTE: Your computer should be equipped with a wireless connector and
properly configured to detect another wireless connection. Refer to your
computer’s documentation on how to configure a wireless connection.
NOTE: Your projector must must have the wireless dongle installed if you want
to use wireless networking. Refer to "Wireless Networking Installation" on
page 74.
Connecting Your Projector
21
Connecting a DVD Player
Connecting a DVD Player Using an S-Video Cable
VGA-OUT
VGA-A IN
VGA-B IN
HDMI
USB-A
Audio-In
Audio-Out
Composite
1
S-Video
Mini-USB
DOUSB
RJ45
RS232
2
UPQ!NFOV
IENJ
NFOV
PQFO0DMPTF
TUBOECZ0PO
EWE0VTC
1
Power cord
2
S-Video cable
VTC
FOUFS
IPNF
NFOV
SFUVSO
NOTE: The S-Video cable is not shipped with your projector. You can purchase
the S-Video extension (50 ft/100 ft) cable on the Dell website at www.dell.com.
22
Connecting Your Projector
Connecting a DVD Player Using a Composite Video Cable
VGA-OUT
VGA-A IN
VGA-B IN
HDMI
USB-A
Audio-In
Audio-Out
Composite
1
S-Video
Mini-USB
DOUSB
RJ45
RS232
2
UPQ!NFOV
IENJ
NFOV
PQFO0DMPTF
TUBOECZ0PO
EWE0VTC
1
Power cord
2
Composite Video cable
VTC
FOUFS
IPNF
NFOV
SFUVSO
NOTE: The Composite Video cable is not shipped with your projector. You can
purchase the Composite Video Extension (50 ft/100 ft) cable on the Dell website
at www.dell.com.
Connecting Your Projector
23
Connecting a DVD Player Using a Component Video Cable
VGA-OUT
VGA-A IN
VGA-B IN
HDMI
USB-A
Audio-In
1
Audio-Out
Composite
S-Video
Mini-USB
DOUSB
RJ45
RS232
2
UPQ!NFOV
IENJ
NFOV
PQFO0DMPTF
TUBOECZ0PO
EWE0VTC
1
Power cord
2
VGA to Component Video cable
VTC
FOUFS
IPNF
NFOV
SFUVSO
NOTE: The VGA to Component Video cable is not shipped with your projector.
You can purchase the VGA to Component Video Extension (50 ft/100 ft) cable on
the Dell website at www.dell.com.
24
Connecting Your Projector
Connecting a DVD Player Using a HDMI Cable
VGA-OUT
VGA-A IN
VGA-B IN
HDMI
USB-A
Audio-In
Audio-Out
Composite
S-Video
Mini-USB
DOUSB
RJ45
RS232
2
1
UPQ!NFOV
IENJ
NFOV
PQFO0DMPTF
TUBOECZ0PO
EWE0VTC
1
Power cord
2
HDMI cable
VTC
FOUFS
IPNF
NFOV
SFUVSO
NOTE: The HDMI cable is not shipped with your projector. You can purchase
the HDMI cable on the Dell website at www.dell.com.
Connecting Your Projector
25
Connecting to Local Area Network
To project an image and control the projector that is connected to a
network through a RJ45 cable.
VGA-OUT
VGA-A IN
VGA-B IN
HDMI
USB-A
Audio-In
Audio-Out
Composite
S-Video
1
Mini-USB
DOUSB
RJ45
RS232
2
Local Area Network (LAN)
1
Power cord
2
RJ45 cable
NOTE: The RJ45 cable is not shipped with your projector. You can purchase the
RJ45 cable on the Dell website at www.dell.com.
NOTE: LAN module kit is not shipped with your S320 projector. If you want to
use the network option, see"Installing the Optional RJ45 Kit" on page 16. You
can purchase it on the Dell website at www.dell.com.
26
Connecting Your Projector
Connection With Commercial RS232 Control Box
VGA-OUT
VGA-A IN
VGA-B IN
HDMI
USB-A
Audio-In
Audio-Out
Composite
S-Video
DOUSB
Mini-USB
1
RJ45
RS232
2
3
1
Power cord
2
RS232 (9-pin D-sub female to female
pin2-3 swap) cable
3
Commercial RS232 control box
NOTE: The RS232 (9-pin D-sub female to female pin2-3 swap) cable is not
shipped with your projector. Consult a professional technician to obtain the
cable.
Connecting Your Projector
27
Connecting With Your Interactive Pen
VGA-OUT
VGA-A IN
VGA-B IN
HDMI
USB-A
Audio-In
Audio-Out
Composite
S-Video
DOUSB
RJ45
RS232
Mini-USB
4
1
2
3
MOLEX
5
1
Power cord
2
VGA to VGA cable
3
USB-A to Mini USB-B cable
4
Projection screen
5
Interactive Pen
28
Connecting Your Projector
NOTE: Interactive module kit is not shipped with your S320 projector. If you
want to use the Interactive feature, see "Installing the Optional Interactive
Module Kit" on page 15. You can purchase it on the Dell website at
www.dell.com.
NOTE:
1 Interactivity is supported only in the following input modes: VGA and HDMI
from a PC, and Wireless Display, USB Display, and LAN Display.
2 To enable Interactive Pen, the 2nd connection between computer and
projector is required. There are four options available for your computer and
projector connections:
a use a Mini USB cable or Dell Interactive wireless dongle (optional)
Dell Interactive wireless dongle is not shipped with your S320 or S320wi
projector. If you want to use Dell Interactive wireless dongle to connect the
computer and the projector, you can purchase it on the Dell website at
www.dell.com.
b use a LAN cable (need to install the Dell Wireless Application Software)
c use WLAN (need to install the Dell Wireless Application Software)
If you use a LAN or WLAN connection, ensure that Wireless/LAN is turned
on first.
3 If the distance between your computer/laptop and projector is over 5 meters,
a USB hub is recommended for your installation.
Connecting Your Projector
29
Using Your Projector
3
Turning Your Projector On
NOTE: Turn on the projector before you turn on the source (computer, DVD
player, etc.). The Power button light blinks blue until pressed.
1 Remove the lens cap.
2 Connect the power cord and appropriate signal cables to the projector. For
information about connecting the projector, see "Connecting Your Projector" on
page 13.
3 Press the Power button (see "Using the Control Panel" on page 35 to locate the
Power button).
4 Turn on your source (computer, DVD player, etc.)
5 Connect your source to the projector using the appropriate cable. See
"Connecting Your Projector" on page 13 for instructions to connect your source
to the projector.
6 By default, the input source of the projector is set to VGA-A. Change the input
source of the projector if necessary.
7 If you have multiple sources connected to the projector, press the Source
button on the remote control or control panel to select the desired source. See
"Using the Control Panel" on page 35 and "Using the Remote Control" on
page 37 to locate the Source button.
Turning Your Projector Off
CAUTION: Unplug the projector after properly shutting down as explained in
the following procedure.
1 Press the Power button. Follow the instruction displayed on screen to properly
turn off the projector.
NOTE: The "Press Power Button to Turn off Projector" message will
appear on the screen. The message disappears after 5 seconds or you can
press the Menu button to clear it.
2 Press the Power button again. The cooling fans continue to operate for 120 seconds.
30
Using Your Projector
3 To power off the projector quickly, press the Power button and hold for 1 second
while the projector’s cooling fans are still running.
NOTE: Before you turn on the projector again, wait for 60 seconds to allow the
internal temperature to stabilize.
4 Disconnect the power cord from the electrical outlet and the projector.
Adjusting the Projected Image
Raising the Projector Height
1 Raise the projector to the desired display angle, and use the front tilt adjustment wheel to fine-tune the display angle.
2 Use the two tilt adjustment wheels to fine-tune the display angle.
Lowering the Projector Height
1 Lower the projector, and use the front tilt adjustment wheels to fine-tune the
display angle.
1
VGA-OUT
VGA-A IN
VGA-B IN
HDMI
USB-A
Audio-In
Audio-Out
Composite
S-Video
Mini-USB
DOUSB
RJ45
RS232
1 2
1
Front tilt adjustment wheel
(Angle of tilt: 0 to 4 degree)
2
1x Rear tilt adjustment wheel
Using Your Projector
31
Adjusting the Projector Focus CAUTION: To avoid damaging the projector, ensure that the front tilt
adjustment wheel is fully retracted before moving the projector or placing the
projector in its carrying case.
NOTE: The carrying case is not shipped with your projector. You can purchase
the carrying case (P/N: 8R3VM) on the Dell website at www.dell.com.
1 Rotate the focus tab until the image is clear. The projector focuses at distances
ranging between 1.31 ft to 12.5 ft (0.4 m to 3.82 m).
1
1
Focus ring
32
Using Your Projector
Adjusting Projection Image Size
S320/S320wi
300" (762.00 cm)
246" (624.84 cm)
139" (353.06 cm)
86" (218.44 cm)
3.51' (1.07 m)
5.71' (1.74 m)
7.91' (2.41 m)
31.45" (79.88 cm)
10.1' (3.08 m)
12.5' (3.82 m)
Projector to screen distance
193" (490.22 cm)
1.31' (0.4 m)
VGA-OUT
VGA-A IN
VGA-B IN
HDMI
USB-A
Audio-In
Audio-Out
Composite
S-Video
Mini-USB
DOUSB
RJ45
RS232
Using Your Projector
33
S320/S320wi
Screen size
Top
(Min zoom)
Desired Distance (m)
<A>
Diagonal (inch)
<B>
W (cm) x H (cm)
From base to top of image (cm)
<C>
31.45
65 x 49
56
0.4
1.07
86
174 x 130
150
1.74
139
283 x 212
244
2.41
193
392 x 294
338
3.08
246
501 x 376
432
3.82
300
610 x 457
526
C
Height (Hd): 244 cm
* This graph is for user reference only.
* Offset Ratio: 115±5%
B
139"
onal:
Diag
A
s
Di
34
Using Your Projector
1.
ce:
n
a
t
74
m
Using the Control Panel
1
2
3
4
10
5
6
9
8
7
1
Power
Turns the projector on or off. For more
information, see "Turning Your Projector On" on
page 30 and "Turning Your Projector Off" on
page 30.
2
Up
/ Keystone
adjustment
Press to navigate through the On-Screen Display
(OSD) Menu items.
Press to adjust image distortion caused by tilting
the projector (+37/-40 degrees).
3
LAMP warning light
If the LAMP amber indicator is on or blinking,
one of the following problems could be occurring:
• Lamp is reaching its end of usable life
• Lamp module is not properly installed
• Lamp driver failure
• Color wheel failure
For more information, see "Troubleshooting Your
Projector" on page 126 and "Guiding Signals" on
page 132.
Using Your Projector
35
4
TEMP warning light
If the TEMP amber indicator is on or blinking,
one of the following problems could be occurring:
• Internal temperature of the projector is too
high
• Color wheel failure
For more information, see "Troubleshooting Your
Projector" on page 126 and "Guiding Signals" on
page 132.
5
Enter
Press to confirm the selection item.
6
IR Receiver
Point the remote control towards the IR receiver
and press a button.
7
Right
Press to navigate through the On-Screen Display
(OSD) Menu items.
/ Auto Adjust
Press to synchronize the projector to the input
source.
NOTE: Auto Adjust does not operate if the
on-screen display (OSD) is displayed.
8
Down
/ Keystone
adjustment
Press to navigate through the On-Screen Display
(OSD) Menu items.
Press to adjust image distortion caused by tilting
the projector (+37/-40 degrees).
9
Left
/ Source
Press to navigate through the On-Screen Display
(OSD) Menu items.
Press to toggle through Analog RGB, Composite,
Component (YPbPr via VGA), HDMI, and
S-Video sources when multiple sources are
connected to the projector.
10
36
Menu
Using Your Projector
Press to activate the OSD. Use the directional
keys and the Menu button to navigate through
the OSD.
Using the Remote Control
POWER
1
14
2
15
ENTER
MENU
16
17
18
19
20
21
3
ASPECT
5
SOURCE
VOL
VIDEO MODE
KEYSTONE
VOL
AUTO ADJ. FREEZE
25
26
1
Power
2
Enter
3
4
Right
Down
6
7
MUTE
MOUSE
8
9
BLANK
22
23
24
4
ZOOM
ZOOM
INFO
VGA
VIDEO
S-VIDEO
10
11
12
13
Turns the projector on or off. For more
information, see "Turning Your Projector On" on
page 30 and "Turning Your Projector Off" on
page 30.
ENTER
Press to confirm the selection.
Press to navigate through the On-Screen Display
(OSD) Menu items.
Press to navigate through the On-Screen Display
(OSD) Menu items.
Using Your Projector
37
5
Aspect Ratio
Press to change the aspect ratio of a displayed
image.
6
Mute
Press to mute or un-mute the projector speaker.
7
Video mode
The projector has preset configurations that are
optimized for displaying data (presentation
slides) or video (movies, games, etc.).
Press the Video Mode button to toggle between
Presentation mode, Bright mode, Movie mode,
sRGB, or Custom mode.
Pressing the Video Mode button once will show
the current display mode. Pressing the Video
Mode button again will switch between modes.
8
Mouse up
Press to move to the previous page.
MUTE
NOTE: The Mini USB cable must be
connected if you want to use the Page Up
feature.
9
Press to move to the next page.
Mouse down
NOTE: The Mini USB cable must be
connected if you want to use the Page Down
feature.
10
Freeze
Press to pause the screen image, then press
"Freeze" again to unfreeze the image.
11
Blank screen
Press to hide/unhide the image.
12
Information
Press to provide projector native resolution
information.
13
S-Video
Press to choose S-Video source.
14
Up
Press to navigate through the On-Screen Display
(OSD) Menu items.
15
Left
Press to navigate through the On-Screen Display
(OSD) Menu items.
16
Menu
Press to activate the OSD.
17
Volume up
18
Source
38
VOL
Using Your Projector
Press to increase the volume.
Press to switch between Analog RGB, Composite,
Component (YPbPr, via VGA), HDMI, and
S-Video source.
19
Volume down
20
Keystone adjustment + Press to adjust image distortion caused by tilting
the projector (+37/-40 degrees).
21
Keystone adjustment ­
Press to adjust image distortion caused by tilting
the projector (+37/-40 degrees).
22
Auto Adjust
Press to synchronize the projector with the input
source. Auto adjust does not operate if the OSD
is displayed.
VOL
Press to decrease the volume.
23
Zoom +
Press to increase the image.
24
Zoom ­
Press to decrease the image.
25
VGA
Press to choose VGA source.
26
Video
Press to choose Composite Video source.
Using Your Projector
39
Using the Interactive Pen
Top View
Bottom View
1
2
6
3
7
5
8
4
1
Replaceable nib
Press the nib to draw or write. When the nib is
engaged, it works like left clicking your mouse to
draw or write.
NOTE:
• If the nib is engaged, the Pen will switch
to Draw mode and the button function
will be temporarily disabled.
• When the nib wears out, change the nib
head as shown below.
Unlock
Lock
40
Using Your Projector
2
Left
This button acts like the left click button of a
mouse.
3
Function
Functions available are listed in the OSD Menu
"Set function" (see page 70).
NOTE: Double-clicking the Function button
will act as Undo, if supported by the
software.
4
Mini USB charge
connector
Allow you use Mini USB cable to charge. See
"Charging the Interactive Pen Battery" on page
44.
5
LED indicators
Two LED indicators are available: Green and
Amber (see "Interactive Pen LED Guiding
Signals" on page 133).
6
Right
This button acts like the right-click button of a
mouse.
7
Power switch
Turns the Interactive Pen on or off.
8
Firmware upgrade
connector
For Interactive Pen and RF board firmware
upgrade.
OSD warning messages - low battery
• The Low Battery warning message pops up when the battery voltage is
lower than 2 V. At this condition, the pen can still work about 1~2 hours.
• The pen will be disabled when the battery voltage is lower than 1.8 V.
Combinations of buttons
• Left + Function: The Pen Information menu appears on the screen.
• Hold Function: Hold the Function button for 2 seconds and the
Function mean will appear on the screen. Use Left/Right to move
up/down and use Function to enter/apply.
• When Toggle is selected in the Set Function menu, press the Function
button to select Normal/Draw/Stable mode.
NOTE: Interactive pen cannot support Windows Mouse property function
"Switch primary and secondary buttons".
Using Your Projector
41
Using the Wrist Strap
Please use the wrist strap as a safety precaution in case of loss of grip on the
Interactive Pen, and prevent damage to the Interactive Pen, surrounding objects,
or injury to other people.
1 Feed the cord on the wrist strap through the connector holder.
2 Wear the wrist strap on your wrist.
42
Using Your Projector
Installing the Remote Control Batteries
NOTE: Remove the batteries from the remote control when not in use.
1 Press the tab to lift the battery compartment cover.
2 Check the polarity (+/-) marking on the batteries.
1
2
according to the marking in the battery compartment.
AAA
AAA
3 Insert the batteries and align their polarity correctly
3
NOTE: Avoid mixing different types of batteries or using
new and old batteries together.
AAA
AAA
4 Slip the battery cover back.
4
Using Your Projector
43
Charging the Interactive Pen Battery
When the Interactive Pen amber battery light starts to blink, its internal battery is
low (If the battery is fully discharged, you will not be able to turn the Interactive
Pen on by pressing its nib, left, right or set function buttons).
To charge the battery, connect a mini USB cable between the Interactive Pen and
your computer or laptop (If connecting to computer or laptop, make sure the
computer or laptop is powered on). The battery light will stay on while the battery
is charging and turn off when the battery is fully charged.
XELOM
When charging is finished, you can unplug the mini USB cable (or keep the cable
connected and use the Interactive Pen while it's charging).
NOTE: For first time use, it takes at least 4-5 hours to fully charge the battery. A
fully charged battery will allow 25 hours of non-stop use or up to 4 weeks in
standby.
CAUTION: The lithium battery is only rechargeable and is not user replaceable
or serviceable. If your Interactive Pen cannot charge, contact Dell (See
"Contacting Dell" on page 144).
CAUTION: Always use the included mini USB cable and your computer (or use
the Docking Charger) to charge the Interactive Pen. The Docking Charger is not
shipped with your projector. You can purchase it on the Dell website at
www.dell.com.
44
Using Your Projector
Docking Charger Introduction (Optional)
Front View
Back View
1
2
3
1
Power LED light
2
Mini USB connector
3
Power switch
4
Power cord connector
4
NOTE: The Docking Charger is not shipped with your S320 or S320wi projector.
You can purchase the Docking Charger on the Dell website at www.dell.com.
LED Indicator on Docking Charger
Green LED Solid
On
When the docking charger is switched on, the Green LED
will turn solid ON.
Green LED Off
The Green LED will turn Off when the docking charger is
switched off.
Using Your Projector
45
LED Indicator on Interactive Pen
Amber LED Solid
On
The Amber LED will turn solid ON during the charge
process.
Amber LED Off
Once battery is fully charged, the LED will turn OFF
indicating "Charge Complete".
Amber LED
Flashing
If the Amber LED starts FLASHING (0.4 sec ON, 0.6 sec
OFF, 1 sec per flashing cycle), it indicates no charging takes
place. Charger error or bad battery is identified.
Docking Charger Specification (Power Supply)
Model:
Interactive Projector Pen Charging Station
Power Supply:
Input AC 100-240 V, 50-60 Hz, 0.2 A
Output DC 5 V/1 A
Maximum temperature:
46
40 ºC
Using Your Projector
Charging the Interactive Pen Battery by
Docking Charger
When the Interactive Pen amber battery light starts to blink, its internal battery is low (If the battery is fully discharged, you won't be able to turn the Interactive Pen on by pressing its nib, left, right or set function buttons).
To charge the battery, you can follow the following steps:
1 Connect the power cable to the wall outlet.
2 Plug the Interactive Pen into the Mini USB port of the docking charger.
3 Turn On the power switch on the docking charger.
Using Your Projector
47
NOTE: During the charging process, Interactive Pen amber battery light will be
lit all the time until the charging process is complete.
NOTE: For first time use, it takes at least 4-5 hours to fully charge the battery. A
fully charged battery will allow up to 25 hours of non-stop use or up to 4 weeks
in standby.
CAUTION: If your docking charger cannot charge, contact DELL.
48
Using Your Projector
Operating Range with Remote Control
TM
S-VIDEO
VIDEO
VGA
INFO
ZOOM
ZOOM
KEYSTONE
VOL
BLANK
MOUSE
±20°
MUTE
SOURCE
VIDEO MODE
VOL
ASPECT
7 m/22.97 feet
MENU
ENTER
Distance
AUTO ADJ. FREEZE
Operating range
Angle
POWER
Distance
Angle
Angle
e
nc
sta
Di
WER
PO
U
MEN
R
TE
EN
CE
UR
SO
VO
NE
TO
YS
KE
L
VO
L
ZO
J.
AD
MOU
ZO
SE
A
ZE
VG
EE
FR
OM
E
OD
OM
VIDE
TE
CT
PE
AS
MU
TO
AU
INFO
O
VIDE
K
AN
BL
OM
TM
O
DE
S-VI
NOTE: Actual operating range may slightly differ from the diagram. Weak
batteries will also prevent the remote control from properly operating the
projector.
Using Your Projector
49
Operating Range with Interactive Pen Distance
Angle
Operating range
Angle
0°
20°
45°
Distance
9 m/29.53 feet
7 m/22.97 feet
5 m/16.4 feet
Angle
e
nc
sta
Di
NOTE:
• Projector is at 2000 lm brightness, with 100 inches image size, and in
Bright mode.
• Can support multiple pens (up to 10 pens) connecting to one projector
but the pens cannot be used simultaneously.
• Actual operating range may slightly differ from the diagram.
• The projector brightness decay will affect the operating range of the pen.
50
Using Your Projector
Using the On-Screen Display
• The projector has a multi-language On-Screen Display (OSD) Menu that can
be displayed with or without an input source.
• Press the Menu button on the control panel or the remote control to enter the
Main Menu.
or
buttons on
• To navigate through the tabs in the Main Menu, press the
your projector's control panel or remote control.
or
button on your projector’s control
• To select a submenu, press the
panel or remote control.
or
buttons on your projector’s control
• To select an option, press the
panel or remote control. When an item is selected, the color changes to dark
blue.
or
buttons on the control panel or remote control to adjust the
• Use the
settings.
button on the control panel or the
• To go back to the Main Menu, press the
remote control.
• To exit the OSD, press the Menu button directly on the control panel or the
remote control.
NOTE: OSD structure and set are the same for the S320 and S320wi models.
INPUT SOURCE
The Input Source menu allows you to select your projector's input source.
VGA-A—Press
to detect a VGA-A signal.
VGA-B—Press
to detect a VGA-B signal.
COMPOSITE—Press
S-VIDEO—Press
HDMI—Press
to detect a Composite Video signal.
to detect a S-Video signal.
to detect a HDMI signal.
WIRELESS/USB—Press
to activate the Input Source WIRELESS/USB menu.
Using Your Projector
51
NOTE: The WIRELESS/USB can be used after the "Wireless and LAN" option is
turned on.
INPUT SOURCE WIRELESS/USB
The Input Source Wireless/USB menu allows you to activate the Wireless Display,
USB Display, and USB Viewer.
to access the projector's Wireless Guide screen. See
WIRELESS DISPLAY—Press
"Wireless Guide screen" on page 76.
USB DISPLAY—Allows you to display the computer/laptop screen to your projector
via the USB cable.
USB VIEWER—Allows you to display photo and PPT files from your USB flash. See
"Presentation to Go (PtG) Installation" on page 83.
AUTO ADJUST
Auto Adjust automatically adjusts the projector's Horizontal, Vertical, Frequency,
and Tracking in PC mode.
52
Using Your Projector
BRIGHTNESS/CONTRAST
The Brightness/Contrast menu allows you adjust the brightness/contrast settings
of your projector.
BRIGHTNESS—Use
CONTRAST—Use
and
and
to adjust the brightness of the image.
to adjust the display contrast.
NOTE: If you adjust the settings for Brightness and Contrast the projector
automatically switch to Custom mode.
VIDEO MODE
The Video Mode menu allows you to optimize the display image: Presentation,
Bright, Movie, sRGB (provides more accurate color representation), and Custom
(set your preferred settings).
Using Your Projector
53
VOLUME
The Volume menu allows you adjust the volume settings of your projector.
VOLUME—Press
to increase the volume and
to decrease the volume.
AUDIO INPUT
The Audio Input menu allows you to select your audio input source. The options
are: Analog In, HDMI, and Wireless/LAN.
NOTE: Avoid line input signal from plugging into microphone port. Otherwise,
user may listen to noises from speakers due to clamping and distortion of audio
signal.
54
Using Your Projector
ADVANCED SETTINGS
The Advanced Settings menu allows you to change settings for Image, Display,
Projector, LAN, Wireless, Menu, Power, Interactive, and Information.
IMAGE SETTINGS (IN PC MODE)—Select and press
to activate image settings. The
image settings menu provides the following options:
COLOR TEMPERATURE—Allows you to adjust the color temperature. The screen
appears cooler at higher color temperatures and warmer at lower color
temperatures. When you adjust the values in the Color Adjust menu, the
Custom mode is activated. The values are saved in the Custom mode.
RGB COLOR ADJUST—Allows you to manually adjust the colors red, green,
and blue.
WHITE INTENSITY—Press
and use
and
to display white intensity.
COLOR SPACE—Allows you to select the color space. The options are: RGB,
YCbCr, and YPbPr.
VGA OUTPUT—Select On or Off the VGA output function at projector
standby status. Default is Off.
NOTE: If you adjust the settings for Color Temperature, RGB Color Adjust, and
White Intensity the projector automatically switch to Custom mode.
IMAGE SETTINGS (IN VIDEO MODE)—Select and press
to activate image settings.
Using Your Projector
55
The image settings menu provides the following options:
COLOR TEMPERATURE—Allows you to adjust the color temperature. The screen
appears cooler at higher color temperatures and warmer at lower color
temperatures. When you adjust the values in the Color Adjust menu, the
Custom mode is activated. The values are saved in the Custom mode.
RGB COLOR ADJUST—Allows you to manually adjust the colors red, green,
and blue.
SATURATION—Allows you to adjust the video source from black and white to
to increase the amount of color in the image
fully saturated color. Press
and
to decrease the amount of color in the image.
SHARPNESS—Press sharpness.
to increase the sharpness and
to decrease the
to increase the amount of green in the image and
to
TINT—Press
decrease the amount of green in the image (available for NTSC only).
WHITE INTENSITY—Press
and use
and
to display white intensity.
COLOR SPACE—Allows you to select the color space. The options are: RGB,
YCbCr, and YPbPr.
VGA OUTPUT—Select On or Off the VGA output function at projector
standby status. Default is Off.
NOTE:
1 If you adjust the settings for Color Temperature, RGB Color Adjust, Saturation,
Sharpness, Tint, and White Intensity the projector automatically switch to
Custom mode.
2 Saturation, Sharpness, and Tint only available when the input source is from
Composite or S-Video.
IMAGE SETTINGS (NO INPUT SOURCE)—Select and press
56
Using Your Projector
to activate image settings.
The image settings menu provides the following options:
VGA OUTPUT—Select On or Off the VGA output function at projector
standby status. Default is Off.
to activate display settings.
DISPLAY SETTINGS (IN PC MODE)—Select and press
The display settings menu provides the following options:
HORIZONTAL POSITION—Press
the image left.
VERTICAL POSITION—Press
image down.
to move the image right and
to move the image up and
to move
to move the
FREQUENCY—Allows you to change the display data clock frequency to
match the frequency of your computer’s graphics card. If you see a vertical
flickering wave, use the Frequency control to minimize the bars. This is a
coarse adjustment.
TRACKING—Synchronize the phase of the display signal with the graphic
card. If you experience an unstable or flickering image, use Tracking to
correct it. This is a fine adjustment.
ASPECT RATIO—Allows you to select the aspect ratio to adjust how the image
appears. Options are: Origin, 16:9, and 4:3.
•Origin — Select Origin to maintain the aspect ratio of the image
projector according to the input source.
Using Your Projector
57
•16:9 — The input source scales to fit the width of the screen to project a
16:9 screen image.
•4:3 — The input source scales to fit the screen and projects a 4:3 image.
ZOOM—Press
and
to zoom and view the image.
Adjust the image scale by pressing
or
to view on your remote control
and press
only.
ZOOM NAVIGATION—Press
Navigation menu.
Use
to activate the Zoom
to navigate the projection screen.
3D DISPLAY—Select On to start the 3D display function (default is Off).
NOTE:
1. When you want to create a 3D experience, you will need a few other
components including:
a
Computer/Laptop with a 120 Hz signal output quad-buffered
graphics card.
b
"Active" 3D glasses with DLP Link™.
c
3D content. See "Note 4".
d
3D Player. (Example: Stereoscopic Player...)
2. Enable the 3D function when it satisfies any of the below-mentioned
conditions:
a
Computer/Laptop with graphics card, capable of outputting at
120 Hz signal via VGA or HDMI cable.
b
Input a suite of 3D content via Video and S-Video.
3. "3D Display" selection will only be enabled in the "Display Settings of
the Advanced Settings" menu when the projector detects either of
the inputs mentioned above.
4. 3D support and refresh rate are as below:
a
VGA/HDMI 1280 x 720, 1024 x 768, and 800 x 600 at 120 Hz
b
Composite/S-Video at 60 Hz
c
Component 480i and 576i
5. The recommended VGA signal for laptop is Single-mode output
(Dual mode is not recommended).
58
Using Your Projector
3D FORMAT—Allows you to select the 3D format. Options are: Side By Side,
Side By Side Full, Frame Sequential, Field Sequential, Top/Bottom, and
Top/Bottom Full.
3D SYNC INVERT—If you see a discrete or overlapping image while
wearing DLP 3D goggles, you may need to execute 'Invert' to get best
match of left/right image sequence to get the correct image. (For DLP
3D goggles)
to activate display settings.
DISPLAY SETTINGS (IN VIDEO MODE)—Select and press
The display settings menu provides the following options:
ASPECT RATIO—Allows you to select the aspect ratio to adjust how the image
appears. Options are: Origin, 16:9, and 4:3.
•Origin — Select Origin to maintain the aspect ratio of image projector
according to the input source.
•16:9 — The input source scales to fit the width of the screen to project a
16:9 screen image.
•4:3 — The input source scales to fit the screen and projects a 4:3 image.
ZOOM—Press
and
to zoom and view the image.
Adjust the image scale by pressing
or
to view on your remote control
and press
only.
ZOOM NAVIGATION—Press
Navigation menu.
Use
to activate the Zoom
to navigate the projection screen.
3D DISPLAY—Select On to start the 3D display function (default is Off).
NOTE:
1. When you want to create a 3D experience, you will need a few other
components including:
Using Your Projector
59
a
Computer/Laptop with a 120 Hz signal output quad-buffered
graphics card.
b
"Active" 3D glasses with DLP Link™.
c
3D content. See "Note 4".
d
3D Player. (Example: Stereoscopic Player...)
2. Enable the 3D function when it satisfies any of the below-mentioned
conditions:
a
Computer/Laptop with graphics card, capable of outputting at
120 Hz signal via VGA or HDMI cable.
b
Input a suite of 3D content via Video and S-Video.
3. "3D Display" selection will only be enabled in the "Display Settings of
the Advanced Settings" menu when the projector detects either of
the inputs mentioned above.
4. 3D support and refresh rate are as below:
a
VGA/HDMI 1280 x 720, 1024 x 768, and 800 x 600 at 120 Hz
b
Composite/S-Video at 60 Hz
c
Component 480i and 576i
5. The recommended VGA signal for laptop is Single-mode output
(Dual mode is not recommended).
3D FORMAT—Allows you to select the 3D format. Options are: Side By Side,
Side By Side Full, Frame Sequential, Field Sequential, Top/Bottom, and
Top/Bottom Full.
3D SYNC INVERT—If you see a discrete or overlapping image while
wearing DLP 3D goggles, you may need to execute 'Invert' to get best
match of left/right image sequence to get the correct image. (For DLP
3D goggles)
to activate projector settings. The
PROJECTOR SETTINGS—Select and press
projector settings menu provides the following options:
60
Using Your Projector
AUTO SOURCE—Select Off (the default) to lock the current input signal. If
you press the Source button when the Auto Source mode is set to Off, you
can manually select the input signal. Select On to auto detect the available
input signals. If you press the Source button when the projector is on, it
automatically finds the next available input signal.
AUTO KEYSTONE—Select On to automatically adjust image distortion caused
by tilting the projector.
PROJECTOR MODE—Allows you to select the projector mode, depending upon
how the projector is mounted.
•Rear Projection-Desktop — The projector reverses the image so that you
can project from behind a translucent screen.
•Rear Projection-Wall Mount — The projector reverses and turns the
image upside down. You can project from behind a translucent screen with
a wall-mounted projection.
•Front Projection-Desktop — This is the default option.
•Front Projection-Wall Mount — The projector turns the image upside
down for wall-mounted projection.
SPEAKER—Select On to enable the speaker. Select Off to the disable
speaker.
CLOSED CAPTION—Select On to enable close caption and activate the closed
caption menu. Select appropriate closed caption options: CC1, CC2, CC3,
and CC4.
NOTE:
1. Closed caption option is available for NTSC only.
2. Closed captioning can only be enabled via S-Video and Composite
Video inputs.
STARTUP SCREEN—Default is Dell logo as wallpaper. You can also select
Capture Screen option to capture the screen display. The following
message appears on the screen.
NOTE: To capture a full image, ensure that the input signal connected
to the projector is at 1024 x 768 resolution.
TEST PATTERN—Test Pattern is used to test focus and resolution.
You can enable or disable the Test Pattern by selecting Off, 1, or 2. You can
and
also invoke the Test Pattern 1 by pressing and holding down
Using Your Projector
61
buttons on the control panel simultaneously for 2 seconds. You can also
and
buttons
invoke the test pattern 2 by pressing and holding down
on the control panel simultaneously for 2 seconds.
Test Pattern 1:
Test Pattern 2:
FACTORY RESET—Select and press
to reset all settings to its factory
default. The below warning message appears:
Reset items include both computer sources and Video source settings.
62
Using Your Projector
LAN SETTINGS—Select and press
to activate LAN settings. The LAN settings
menu provides the following options:
WIRELESS AND LAN—Select Enabled to activate the Wireless and LAN
function.
DHCP—If a DHCP server exists in the network to which the projector is
connected, the IP address will automatically be acquired when you select
DHCP On. If DHCP is Off, manually set the IP Address, Subnet Mask,
and
to select the number of IP address, Subnet
and Gateway. Use
Mask, and Gateway. Key in enter to confirm each number and then use
and
to set the next item.
IP ADDRESS—Automatically or manually assigns the IP address to the projector connected to the network.
SUBNET MASK—Configure the Subnet Mask of the network connection.
GATEWAY—Check the Gateway address with your network/system administrator if you configure it manually.
DNS—Check the DNS Server IP address with your network/system
administrator if you configure it manually.
STORE—Press
settings.
to save the changes made in network configuration
NOTE:
1. Use
and
button to select IP Address, Subnet Mask,
Gateway, DNS, and Store.
2. Press the
button to enter IP Address, Subnet Mask, Gateway or
DNS to set the value. (The selected option is highlighted in blue)
a
Use
and
b
Use and
c
After the setup is complete, press the button to select the option.
button to set the value.
button to exit.
Using Your Projector
63
3. After the IP Address, Subnet Mask, Gateway, and DNS is set up,
button to store the settings.
select Store and press
4. If you select Store without pressing the Enter button, the system will
keep the original settings.
RESET—Press
to reset network configuration.
to activate wireless settings. The wireless
WIRELESS SETTINGS—Select and press
settings menu provides the following options:
WIRELESS—If your projector has been installed the wireless dongle, this
option is the Connected.
DHCP SERVER—Allows you to enable DHCP server of the wireless.
START IP ADDRESS—Automatically or manually assigns the Start IP address
of the DHCP server to the projector connected to the wireless.
END IP ADDRESS—Automatically or manually assigns the End IP address of
the DHCP server to the projector connected to the wireless.
SUBNET MASK—Configure the Subnet Mask of the wireless connection.
GATEWAY—Check the Gateway address with your network/system
administrator if you configure it manually.
DNS—Check the DNS Server IP address with your network/system
administrator if you configure it manually.
STORE—Press
settings.
to save the changes made in wireless configuration
NOTE:
1. Use
and
button to select IP Address, Subnet Mask,
Gateway, DNS, and Store.
button to enter IP Address, Subnet Mask, Gateway, or
2. Press the
DNS to set the value. (The selected option is highlighted in blue)
64
a
Use
and
buttonto select the option.
b
Use and
button to set the value.
c
After the setup is complete, press the Using Your Projector
button to exit.
3. After the IP Address, Subnet Mask, Gateway, and DNS is set up,
button to store the settings.
select Store and press
4. If you select Store without pressing the Enter button, the system will
keep the original settings.
RESET—Press
to reset wireless configuration.
to activate the menu settings. The menu
MENU SETTINGS—Select and press
settings consists of the following options:
MENU POSITION—Allows you to change the position of the OSD menu on
the screen.
MENU TIMEOUT—Allows you to adjust the time for an OSD timeout. By
default, the OSD disappears after 20 seconds of non-activity.
MENU TRANSPARENCY—Select to change the transparency level of the OSD
background.
MENU LOCK—Select On to enable the Menu Lock and hide the OSD menu.
Select Off to disable the Menu Lock. If you want to disable the Menu Lock
function and have the OSD disappear, press the Menu button on the
control panel or remote control for 15 seconds, and then disable the
function.
PASSWORD—When Password Protect is enabled, a Password Protect screen
requesting you to enter a password will be displayed when the power plug is
inserted into the electrical output and the power for the projector is first
turned on. By default, this function is disabled. You can enable this feature
by selecting Enabled. If the password has been set before, key in the
password first and select the function. This password security feature will
be activated the next time you turn on the projector. If you enable this
feature, you will be asked to enter the projector’s password after you turn
on the projector:
1 First time password input request:
Using Your Projector
65
a Go to Menu Settings, press
the password settings.
and then select Password to Enabled
b Enabling the Password function will pop up a change screen. Key in a
.
4-digit number from the screen and press
S320wi
Password screen
S320 Password screen
c To confirm, enter the password again.
d If the password verification is successful, you may resume with accessing
the projector's functions and its utilities.
2 If you have entered an incorrect password, you will be given another two
chances. After three invalid attempts, the projector will automatically turn
off.
NOTE: If you forget your password, contact DELL™ or a qualified
service personnel.
3 To disable the password function, select the Disabled option to close the
function.
4 To delete the password, select the Delete option.
66
Using Your Projector
CHANGE PASSWORD—Key in the original password. Then, enter the new
password and confirm the new password again.
S320wi Change Password screen
S320 Change Password screen
to activate power settings. The power
POWER SETTINGS—Select and press
settings menu provides the following options:
Using Your Projector
67
QUICK SHUTDOWN—Select On to turn off the projector with a single press of
the Power button. This function allows the projector to quickly power off
with an accelerated fan speed. Slightly higher acoustic noise is expected
during quick power off.
NOTE: Before you turn on the projector again, wait for 60 seconds to
allow the internal temperature to stabilize. The projector will take a
longer time to turn on if you try to power on immediately. Its cooling fan
will run at full speed for about 30 seconds to stabilize the internal
temperature.
POWER SAVING—By default, the projector is set to enter power saving mode
after 120 minutes of no activity. A warning message appears on screen
showing a 60 seconds countdown before switching to power saving mode.
Press any button during the countdown period to stop the power-saving
mode.
You can also set a different delay period to enter power saving mode. The
delay period is the time you want the projector to wait without an input
signal.
If an input signal is not detected during the delay period, the projector
turns off. To turn on the projector press the Power button.
DURING STANDBY—Select Wireless On or Off set the Wireless/LAN model
on/off while the projector is standby status (default is Wireless Off).
LAMP MODE—Allows you to select the Normal or ECO or Dynamic mode.
Normal mode operates at full power level. ECO mode operates at a lower
power level which may provide longer lamp life, quieter operation, and
dimmer luminance output on the screen.
DYNAMIC—Select and press
LAMP HOUR RESET—Press
lamp hour.
68
Using Your Projector
to activate image care feature.
and select the Confirm option to reset the
INTERACTIVE SETTINGS—Select and press
to activate Interactive settings. The
Interactive settings menu provides the following options:
NOTE: The S320 projector must be installed with a Interactive Module
Kit if you want to use the Interactive feature. Refer to "Installing the
Optional Interactive Module Kit" on page 15.
INTERACTIVE—Default option is On. Select Off to disable the Interactive
Pen function.
NOTE:
1. Ensure that the Interactive Pen is connected. See "Connecting With
Your Interactive Pen" on page 28.
2. Interactive Pen cannot be used in the extend mode.
3. Interactivity is supported only in the following input modes: VGA and
HDMI from a Computer, and Wireless Display, LAN Display, or USB
Display.
CHANNEL—Allows you to set the channel selected as Auto or Manual.
•Auto — Channel is selected automatically.
•Manual — Channel is selected manually. A total of 30 channels are
available.
CONNECTOR—Allows you to set the connector selection as Mini USB or
Wireless/LAN.
to activate Pen settings. The Pen
PEN SETTINGS—Select and press
settings menu provides the following options:
Using Your Projector
69
POINTER MOTION—Allows you to select the Pointer Motion mode:
Normal, Draw, and Stable.
•Normal — In the Normal mode, pressing the Left button of the
Interactive Pen holds the position of the pointer for a moment. This
mode is best to use the Interactive Pen like a mouse, i.e., for left click
and double click function.
•Draw — In Draw mode, the position can move freely for drawing.
This mode is best for drawing or writing on the screen.
•Stable — In the Stable mode, pressing and holding the Left button of
the Interactive Pen limits the pointer to vertical or horizontal moves
only. If the left button is released, the pointer can resume to move
freely. This mode is best for drawing vertical or horizontal lines on the
screen.
CLICK SPEED—Allows you to set the mouse pause time. This function is
only available in Normal mode. The available options are: Fast,
Medium, and Low.
•Fast — Set the pointer motion freeze time to the minimum amount
of time, 0.5 seconds.
•Medium — Set the pointer motion freeze time to the middle value,
1.0 seconds.
•Low — Set the pointer motion freeze time to the maximum amount
of time, 1.5 seconds
SET FUNCTION—Allows you to set the function of the Function button
on the Interactive Pen. Available options are: Toggle:
Normal/Draw/Stable, PowerPoint Annotation, Switch Windows (Alt
+ Tab), Esc, Show Desktop (Cmd + D), Open Windows Explorer
(Cmd + E), Middle Mouse, Double Click, and Disable (See "Using
the Interactive Pen" on page 40).
•Toggle: Normal/Draw/Stable — Function as toggling among Normal,
Draw, and Stable mode.
•PowerPoint Annotation — Function as annotating in the PowerPoint
slide show.
70
Using Your Projector
•Switch Windows (Alt + Tab) — Function as toggling among
windows, acting as the keyboard shortcut Alt + Tab.
•Esc—Function as the keyboard Esc button.
•Show Desktop (Cmd + D) — Function as showing desktop,
minimizing all windows.
•Open Windows Explorer (Cmd + E) — Set the function as opening
the Windows Explorer.
•Middle Mouse — Set the function as the scroll wheel of the mouse.
•Double Click — Set the function as double-clicking.
•Disable — Disable the Function button.
PAIRING MODE—Allows you to set the pairing mode selection as Open or
Fixed.
•Pairing Mode — When you select Open, follow the on-screen steps
to set your Interactive Pen into the open mode. (This mode can let you
use your Interactive Pen with any Dell interactive projector when the
pen points to the screen.)
•Fixed Mode — When you select Fixed, follow the on-screen steps to
complete the pairing between Projector and Interactive Pen. (This
mode is to make sure your Interactive Pen pairing with your designated
projector.)
Once paired, the Pen will automatically fix to the projector every time
it turns on.
RESET—Press
and select Confirm option to reset the Pen settings.
Using Your Projector
71
INFORMATION—Allows you to view the Pen 1 or Pen 2 information.
INFORMATION—The information menu displays the current S320 or S320wi
projector settings.
LANGUAGE
Allows you to set the language for the OSD. Press
menu.
72
Using Your Projector
to activate the Language
HELP
If you encounter problems with your projector, you can access the help menu for
troubleshooting.
Using Your Projector
73
Wireless Networking Installation
NOTE: Your computer must have the following minimum system requirements:
Operating System:
• Windows
Microsoft Windows XP™ Home or Professional Service pack 2 (32-bit
recommended), Windows Vista 32-bit, and Windows® 7 Home or Professional
32-bit or 64-bit
• MAC
MacBook and above, MacOS 10.5 and above
Minimum Hardware:
a Intel Dual Core 1.4 MHz or higher
b 256 MB of RAM required, 512 MB or more recommended
c 10 MB of available hard-disk space
d nViDIA or ATI graphic card must with 64 MB VRAM or above
e Ethernet adapter (10 / 100 bps) for an Ethernet connection
f A supported WLAN adapter for a WLAN connection (any NDIS-compliant
802.11b or 802.11g or 802.11n Wi-Fi device)
Web browser
Microsoft Internet Explorer 6.0 or 7.0 (recommended) or 8.0, Firefox 1.5 or 2.0,
and Safari 3.0 and above
NOTE: Wireless Networking Installation steps are the same for the S320 and
S320wi models.
74
Using Your Projector
Enable Wireless on the Projector
In order to use your projector wirelessly, you need to complete the steps below:
1
Install the optional wireless module kit (optional in S320). See "Installing the
Optional Wireless Module Kit" on page 14.
NOTE: Wireless module kit embedded for S320wi.
2
Connect the power cable to the wall outlet and press the power button.
3
Press the Menu button on your projector control panel or remote control.
NOTE: Use
,
,
and
buttons to navigate and
to select.
4 Access the INPUT SOURCE menu, select Wireless/USB and then select
Wireless Display on the sub-menu. See "INPUT SOURCE
WIRELESS/USB" on page 52.
Using Your Projector
75
The Wireless Guide Screen shown below appears:
5 Take note of the LOGIN CODE, NETWORK NAME (SSID), and IP
ADDRESS. You will need these information to log in in later.
Install the Wireless Application Software on Your Computer
In order to use your wireless projector, you must install the software on your
system.
6
Connect your computer to the S320 or S320wi wireless network.
NOTE:
• Your computer must have wireless network function to detect the
connection.
76
Using Your Projector
• When you connect to the S320 or S320wi wireless network, you will lose
wireless connectivity with other wireless networks.
NOTE: Remember to turn off all proxies. (In Microsoft® Windows Vista: Click
Control Panel J Internet Options J Connections J LAN Settings)
7
Open your internet browser. You will be automatically directed to the S320
or S320wi Web Management web page.
NOTE: If the web page does not load automatically, enter the IP address
(default IP address is 192.168.100.10) noted from the projector’s screen in the
browser’s address bar.
Using Your Projector
77
8
The S320 or S320wi Web Management page opens. For first-time use, click
Download.
9
Select the appropriate operating system, then click Download.
78
Using Your Projector
10 Click Run to proceed with
the one-time installation of
the software.
NOTE: You may choose to
save the file and install it at a
latter time. To do this, click
Save.
NOTE: Audio projection function need install extra driver only in Windows XP. If
your computer does not have the driver installed, a pop-up message will
appear on-screen prompting you to install the required driver. You can
download the “Audio Projection Driver” from the Dell Support site at
support.dell.com.
NOTE: If you are unable to install the application because of inadequate rights
on the computer, please contact your network administrator.
11 The installation software will launch. Follow the on-screen instruction to
complete setup.
Using Your Projector
79
Launch the Wireless Application
Once the installation is complete, the S320 or S320wi wireless application will
launch and search automatically. If the program not launch automatically, you can
double-click the
or
icon on the desktop to start the application.
Login
To communicate with your projector, enter the Login Code provided in Step 6 of
Wireless Networking Installation, then click OK.
NOTE: If the IP Address is not detected, enter the IP Address displayed at the
bottom left corner of the screen.
NOTE: Please not click "Interactive Pen only" box in the log in screen when you
use the wireless display or LAN display.
80
Using Your Projector
Understanding the Buttons
After a successful log in, the following screen appears:
1
2
1
2
3
3
Item
Description
Status Bar
Displays IP and LOGIN CODE information.
Menu
Click to activate the application menu.
Minimize button
Click to minimize the application.
Close button
Click to exit the application.
Controls Toolbar
Full screen
Click to project the image in full screen.
Split 1
Click to project the image in the upper left
corner of the screen.
Split 2
Click to project the image in the upper right
corner of the screen.
Split 3
Click to project the image in the lower left
corner of the screen.
Split 4
Click to project the image in the lower right
corner of the screen.
Stop
Click to stop projection.
Pause
Click to pause projection.
Audio Projection
Click to enable audio projection.
Connection Status
Connection Icon
Blinks when projection is in progress.
Projecting the Presentation
•
•
•
•
To project the presentation, click any of the projection buttons
To pause the presentation, click
. The icon turns green.
again.
To continue the presentation, click
.
To audio projection the presentation, click
Using Your Projector
.
81
• To stop the presentation, click
.
NOTE: WLAN environment using 802.11g connection, and no screen
stretching.
NOTE: Your computer will not enter S1 (standby mode) / S3 (sleep mode) / S4
(hibernate mode) when running a wireless, USB Display, or USB Viewer
presentation.
Using the Menu
Click
to display the menu.
WEB MANAGEMENT—Click to open the Web Management page. See "Managing the
Projector From Web Management (for Wireless Network)" on page 95.
SEARCH FOR PROJECTOR—Click to search and connect to wireless projector.
MAKE APPLICATION TOKEN—Click to make application token. See "Make Application Token" on page 125.
ADVANCE SCREEN CAPTURE—The default is enable. Click to disable the advance
screen capture.
INFO—Click to display system information.
HOTKEY—Click to display the hotkey information.
ABOUT—Click to display the application version.
EXIT—Click to close the application.
82
Using Your Projector
Presentation to Go (PtG) Installation
Minimum system requirements to install PtG are as follow:
Operating System:
- Windows Microsoft Windows XP™ Home or Professional Service pack 2/3 (32-bit recommended), Windows® Vista 32-bit, or Windows® 7 Home or Professional
32-bit or 64-bit
- Office 2003 or Office 2007
NOTE: Presentation to Go (PtG) installation steps are the same for the S320 and
S320wi models.
In order to use your USB Viewer, you need to complete the steps below:
1 Install the optional wireless module kit. See "Installing the Optional Wireless Module Kit" on page 14.
NOTE: Wireless module kit embedded for S320wi (optional in S320).
2 Plug the USB Flash to your projector.
NOTE:
• Only supports the JPEG format photo within 10 Mb x 40 M pixels.
• The PtG converter can convert your PowerPoint files into PtG files. See
"Using the PtG Converter" on page 87.
• You can download the "PtG Converter - Lite" in the Dell Support website at:
support.dell.com.
3 At INPUT SOURCE menu, select Wireless/USB and then select USB
Viewer on the sub-menu. See "INPUT SOURCE WIRELESS/USB" on
page 52.
NOTE: When the Wireless and LAN function is disabled, go to LAN Settings
menu, select the "Enabled" in the "Wireless and LAN" option to re-activate the
Wireless and LAN function.
Using Your Projector
83
PtG Viewer
System will stay in this page when ready.
Photo Viewer
84
Using Your Projector
PtG/Photo Function Introduction
Show valid PtG and Photo files which are stored in the USB disk.
NOTE: If only one disk is detected, the system will skip this step.
PtG Overview
Using Your Projector
85
Photo Overview
NOTE: Supports 14 languages of photo files name format (Languages: English,
Dutch, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian,
Simplified Chinese, Spanish, Swedish, and Traditional Chinese).
Buttons Introduction
Use the up, down, and left buttons to navigate and
control panel or remote control to select.
button on your projector's
Button
Up
Down
Left
Right
Enter
PtG function
Up
Down
Back
No function
Enter
PtG Playback
Pre Page
Next Page
Back
No function
Next Pause
Photo
function
Up
Down
Back
No function
Enter
Photo
Playback
Pre Page
Next Page
Back
No function
No
function
NOTE: If you enter the OSD menu while using PtG, PtG navigation by the up,
down, and left buttons will not function.
86
Using Your Projector
Install the PtG Converter Application Software on Your Computer
Please follow the on-screen instructions to complete the setup.
NOTE: You can download the "PtG Converter - Lite" in the Dell Support website
at support.dell.com.
Using the PtG Converter
1
Launch the "PtG Converter - Lite.exe" or double-click the
desktop to start the application.
2
Click
icon on the
to select a PowerPoint file and start conversion.
Using Your Projector
87
3
Click Browse button to select the storage location and then press OK.
NOTE:
1 If your computer does not have MS PowerPoint installed, file convert will fail.
2 PtG converter only supports up to 20 pages.
3 PtG converter only supports conversion of .ppt files to .PtG files.
88
Using Your Projector
Audio Projection Installation
Audio Projection only supports the Wireless Display and LAN Display input
source.
Minimum system requirements as follow:
Operating System:
• Windows
Microsoft Windows XP™ Home or Professional Service pack 2/3 (32-bit
recommended), Windows Vista 32-bit, or Windows® 7 Home or
Professional 32-bit or 64-bit
• MAC
MacBook Pro and above, MacOS 10.5 and above
Minimum Hardware:
a
Intel® Core™ i5-460 MHz (2.53 GHz/Turbo 2.8 GHz) or greater
b
1 GB DDR3 VRAM independent graphics card or more recommended
c
2 GB dual channel DDR3 SDRAM memory at 1066 MHz required or
more recommended
d
Gigabit Ethernet
e
Integrated 802.11 b/g/n Wi-Fi Device for a WLAN connection
NOTE: If your computer does not meet the minimum hardware requirements,
audio projection may have lag or noise. Meet the recommended system
requirements to have optimized performance of audio projection.
NOTE: If you want to use wireless for audio projection, need installed the
optional wireless dongle. See "Installing the Optional Wireless Module Kit" on
page 14.
NOTE: Audio projection function need install extra driver only in Windows XP, If
your computer does not have the driver installed, a pop-up message will appear
on-screen prompting you to install the required driver. You can download the
“Audio Projection Driver” from the Dell Support site at support.dell.com.
NOTE: Audio Projection function need installed extra drive in MAC operating
system. If your MAC computer does not have the driver installed, a pop-up
message will appear on-screen prompting you to install the required driver. You
can download the "Soundflower Driver" from the some search engine sites (ex.
Yahoo, MSN...). The "Soundflower Driver" is free application.
NOTE: Audio projection setting steps are the same for the S320 and S320wi
models.
Using Your Projector
89
NOTE: Ports / Protocol for connection to the projector for projection via
Ethernet:
90
UDP: 1047,
(backup: 1048, 1049)
TCP:
(backup: 389, 8080, 21)
3268, 515, 1688, 1041
Using Your Projector
Enable Wireless or LAN on the Projector
1 Install the optional wireless module kit (optional in S320). See "Installing the
Optional Wireless Module Kit" on page 14.
NOTE: If you select install the LAN module kit (optional), see "Installing the
Optional RJ45 Kit" on page 16.
2 Connect the power cable and turn on the projector by pressing the power button.
NOTE:
a
If the LAN is used for audio projection, follow these steps to enable Wireless
and LAN function (default is Enabled): Advanced Settings
LAN Settings
Wireless and LAN
Enabled.
b
If the Wireless is used for audio projector, please install a wireless dongle to
your projector.
3 Access the Input Source menu, select the Wireless/USB and then select the
Wireless Display on the sub-menu.
Using Your Projector
91
The Wireless Guide Screen shown below appears:
4 Take note of the LOGIN CODE, NETWORK NAME (SSID), and IP ADDRESS. You will need these information to log in later.
Install the Wireless Application Software on Your Computer
5 "Wireless Application Software" is required if the Wireless or LAN is used for
the Audio Projection set-up. Please download and install the software the first
time you use Audio Projection. If it is already installed, skip Step 5 - 6.
NOTE: You only need to install the "Wireless Application Software" once.
6 Wireless Application Software download and install steps refer to steps 7 to 12
of the "Wireless Networking Installation" on page 74.
92
Using Your Projector
NOTE: If the LAN is used for audio projection, connect the LAN cable to the
projector and the computer.
Launch the Wireless Application
7 Once the installation is complete, the program will launch automatically. Or
you can double-click the
or
icon on the desktop to start the
application.
NOTE:
1 When you select the LAN for projection, click "Skip".
2 When you select the Wireless for projection, select the Dell S320 Wireless
or Dell S320wi Interactive, and the click "OK".
Using Your Projector
93
Login
8 To communicate with your projector, enter the Login Code (see Step 4), and
then click OK.
NOTE: If the IP Address is not detected, enter the IP Address displayed at the
bottom left corner of the wireless screen.
9 You are now logged into the S320 or S320wi Wireless Application. Click the
"Play" button in the application to starting the LAN or wireless projection.
NOTE: You may use the controls to either project in full screen mode or in split
screen mode.
10 Click the "Audio Projection" button in the application to enable Audio
Projection function.
NOTE: Audio Projector function need install extra driver only in Windows XP,If
your computer does not have the driver installed, a pop-up message will appear
on-screen prompting you to install the required driver. You can download the
“Audio Projection Driver” from the Dell Support site at support.dell.com.
11 Executing the Windows Media Player or others audio player software
(example: Winamp player...) on your computer.
94
Using Your Projector
Managing the Projector From Web
Management (for Wireless Network)
Configuring the Network Setting
If the projector is connected to a network, you can access the projector using a web
browser. For configuring the network setting, refer to "LAN Settings" on page 63.
Accessing Web Management
Use Internet Explorer 5.0 and above or Firefox 1.5 and above and enter the IP
address. You can now access Web Management and manage the projector from a
remote location.
NOTE: Web management and set are the same for the S320 and S320wi
models.
Home Page
• Access the Web Management Home page by entering the projector’s IP
address at the web browser. See "LAN Settings" on page 63.
• Select the language for web management from the list.
• Click any menu item on the left tab to access the page.
Using Your Projector
95
Download the Wireless Application Software
See also "Wireless Networking Installation" on page 74.
Click the Download button of the corresponding operating system of your
computer.
96
Using Your Projector
Conference Control
This allows you to host conference presentations from different sources without
using projector cables and lets you control how each presentation will appear on
screen.
NOTE: Without Conference Play Control, the last user to hit the "Play" button on
the application will take control of the full-screen projection.
Computer Name: Lists the computers logged for conference control.
Play Control: Click the buttons to control how each computer’s projection will
appear on screen.
•
Full screen projection — The presentation from the computer
occupies the whole screen.
•
Split 1 - The presentation from the computer appears on the upper
left corner of the screen.
•
Split 2- The presentation from the computer appears on the upper
right corner of the screen.
•
Split 3- The presentation from the computer appears on the lower
left corner of the screen.
•
Split 4- The presentation from the computer appears on the lower
right corner of the screen.
•
Stop - Projection from the computer is stopped.
IP Address: Shows each computer’s IP Address.
NOTE: To end the conference, click Home.
Using Your Projector
97
Managing Properties
Admin
An administrator password is required to access the Admin page.
• Admin Password: Enter the administrator password and then click Login.
The default password is "admin". To change the password, see "Change
Passwords" on page 103.
98
Using Your Projector
System Status
Displays the Network Status, Connection Status, and Projector Status
information.
Using Your Projector
99
Network Status
See OSD section on page 63.
IP Setup
• Choose Obtain an IP address automatically to assign an IP address to the
projector automatically, or Use the following IP address to assign an IP
address manually.
DHCP Server Setup
• Choose Auto to automatically set up the Start IP, End IP, Subnet Mask,
Default Gateway, and DNS Server address from a DHCP server, or Disable
to disable this function.
Wireless Setup
•
100
Choose Enable to set up the Region, SSID, SSID Broadcast, Channel,
Encryption, and Key. Choose Disable to disable the wireless set up.
Using Your Projector
SSID: Up to maximum length of 32 characters.
Encryption: You can Disable WPA key or select one of 64-bit or 128-bit in
ASCII or HEX string.
Key: If Encryption is enabled, you have to set key value according to the
Encryption mode you selected.
RADIUS Server Setup
• Set up the IP address, Port, and Key information.
GateKeeper
• There are three options:
All Pass: Allow users to access the office network via the wireless projector.
All Block: Block users from accessing the office network via the wireless
projector.
Internet Only: Block users from the office network, but still reserve Internet connection capability.
Set Security For SNMP
• Setup Write Community information.
Click the Apply button to save and apply changes. The projector must be restarted
for the changes to take effect.
Using Your Projector
101
Projection Setup
Projection Setup
• Resolution: Allows you to select the resolution. Options are: XGA (1024 x 768) and WXGA (1280 x 800).
• Login Code: Select how you want the login code to be generated by the
projector. There are three options:
•
Disable: Login code will not be required when logging in to the system.
•
Random: Default is Random. Login code will be randomly generated.
•
Use the following code: Enter a 4-digit code. This code will be used to
log in to the system.
Projector Setup
•
Set up the Model Name, Projector Name, Location, and Contact
information (up to 21 characters for each field).
Click the Apply button to save and apply changes. The projector must be restarted
for the changes to take effect.
102
Using Your Projector
Change Passwords
This page allows you to change the administrator password.
•
Enter New Password: Enter the new password.
•
Confirm New Password: Enter the password again and click Apply.
NOTE: Contact Dell if you forget your administrator password.
Using Your Projector
103
Reset to Default
Click the Apply button to restore the wireless/network setup to its factory default
settings.
104
Using Your Projector
Firmware Upgrade
Use the Firmware Upgrade page to update your projector’s wireless firmware.
NOTE: Please disable and enable wireless/network using the OSD to restart
the network card for the projector after firmware upgrade is successful.
To start firmware update, follow these steps:
1
Press Browse to select the file to update.
2
Click the Update button to start. Wait while the system updates the
firmware in your device.
CAUTION: Do not interrupt the update process as this may cause the system
to crash!
3
Click OK when the update is complete.
Using Your Projector
105
Projector Control Panel
Projector Information
• Projector Status: There are five states: Lamp On, Standby, Power Saving,
Cooling, and Warming up. Click Refresh to refresh the status and control
settings.
• Power Saving: Power Saving can be set to Off, 30, 60, 90, or 120 minutes. For
more information, see "Power Saving" on page 68.
• Alert Status: There are three alert states: Lamp warning, Low lamp life, and
Temperature warning. Your projector might lock up in the protection mode
if any of the alerts are activated. To exit the protection mode, click Clear to
clear the Alert Status before you power on your projector.
106
Using Your Projector
Image Control
• Projector Mode: Allows you to select the projector mode, depending on how
the projector is mounted. There are four projection modes: Front
Projection-Desktop, Front Projection-Wall Mount, Rear Projection-Desktop,
and Rear Projection-Wall Mount.
• Source Select: The Source Select menu allows you to select your projector's
input source. You can select VGA-A, VGA-B, S-Video, Composite Video,
HDMI, Wireless Display, USB Display, or USB Viewer.
• Video Mode: Select a mode to optimize the display image based on how the
projector is being used:
- Presentation: Best for presentation slides.
- Bright: Maximum brightness and contrast.
- Movie: For viewing movies and photos.
- sRGB: Provides a more accurate color representation.
- Custom: User-preferred settings.
• Blank Screen: You can select On or Off.
• Aspect Ratio: Allows you to select the aspect ratio to adjust how the image
appears.
• Brightness: Select value to adjust the brightness of the image.
•
Contrast: Select value to adjust the display contrast.
Click the Auto Adjust button to adjust the settings automatically.
Audio Control
• Audio Input: Select the input source. Options are: Analog In, HDMI, and
Wireless/LAN.
• Volume: Select the value (0~20) for audio volume.
• Speaker: Select On to enable the audio function or select Off to disable the
audio function.
Click the Factory Reset button to restore the factory default settings.
Using Your Projector
107
Alert Setting
E-mail Alert
• E-mail Alert: You can set whether to be notified by email (Enable) or not
(Disable).
• To/Cc/From: You can enter email address of sender (From) and recipients
(To/Cc) to receive notification when an abnormality or warning occurs.
•
Subject: You can enter the subject line of the email.
Click the E-mail Alert Test button to test the e-mail alert settings.
SMTP Setting
• Out going SMTP server, User name, and Password should be provided by
your network administrator or MIS.
Alert Condition
• You can select the abnormalities or warnings to be notified by email. When
any of the alert conditions occur, an email will be sent to the recipients
(To/Cc).
Click the Save button to the save settings.
NOTE: E-mail alert is designed to work with a standard SMTP server using the
default 25 port. It does not support encryption and authentication (SSL or TLS).
108
Using Your Projector
Reboot System
Click Reboot to reboot the system.
Crestron
For Crestron function.
Using Your Projector
109
Managing the Projector From Web
Management (Network RJ45 Kit is Optional for
S320)
Configuring the Network Setting
If the projector is connected to a network, you can access the projector using a web
browser by configuring the network setting (TCP/IP). When using the network
function, the IP address should be unique. For configuring the network setting,
refer to "LAN Settings" on page 63.
The RJ45 kit is not shipped with your S320 projector. You can purchase it on the
Dell website at www.dell.com. See "Installing the Optional RJ45 Kit" on page 16.
Accessing Web Management
Use Internet Explorer 5.0 and above or Firefox 1.5 and above and enter the IP
address. You can now access Web Management and manage the projector from a
remote location.
110
Using Your Projector
Managing Properties
Home
• Access the Web Management Home page by entering the projector’s IP
address at the web browser. See "LAN Settings" on page 63.
• Language: Allows you to set the language for web management.
Using Your Projector
111
Network Settings
•
Set up the Model Name, Projector Name, Location, and Contact
information (up to 21 characters for each field). Press Save to store the
settings.
• Choose DHCP to assign an IP address to the projector from a DHCP server
automatically, or Manual to assign an IP address manually.
•
112
Set up the IP Address, Device ID, and Port information on the Crestron
function.
Using Your Projector
Projector Status and Control Page
• Projector Status: There are 5 status: Lamp On, Standby, Power Saving,
Cooling, and Warming up. Click the Refresh button to refresh the status
and control settings.
• Power Saving: Power Saving can be set to Off, 30, 60, 90, or 120 minutes.
Refer to page 68.
• Alert Status: There are three error status: Lamp warning, Low lamp life, and
Temperature warning. Your projector might lock up in protection mode if
any of the alerts is activated. To exit protection mode, click the Clear to
clear the Alert Status before you could Power ON your projector.
• Projector Mode: Allows you to select the projector mode, depending on how
the projector is mounted. There are four projection modes: Front
Projection-Desktop, Front Projection-Wall Mount, Rear Projection-Desktop
and Rear Projection-Wall Mount
• Source Select: The Source Select menu allows you to select your projector's
input source. You can select VGA-A, VGA-B, S-Video, Composite Video,
HDMI, Wireless Display, USB Display, or USB Viewer.
• Video Mode: Select a mode to optimize the display image based on how the
projector is being used:
- Presentation: Best for presentation slides.
Using Your Projector
113
- Bright: Maximum brightness and contrast.
- Movie: For viewing movie & photo.
- sRGB: Provide a more accurate color representation.
- Custom: User preferred settings.
• Blank Screen: You can select On or Off.
• Aspect Ratio: Allows you to select the aspect ratio to adjust how the image
appears.
• Brightness: Select value to adjust the brightness of the image.
•
Contrast: Select value to adjust the display contrast.
Click the Auto Adjust button to adjust the settings automatically.
• Audio Input: Select the input source. Options are: Analog In, HDMI, and
Wireless/LAN.
• Volume: You can select the value (0~20) for the audio volume
• Speaker: You can select On to enable the audio function or select Off to
disable the audio function.
Click the Factory Reset button to restore the factory default settings.
114
Using Your Projector
E-mail Alert
• E-mail Alert: You can set whether to be notified by email (Enable) or not
(Disable).
• To/Cc/From: You can enter email address of sender (From) and recipients
(To/Cc) to receive notification when an abnormality or warning occurs.
• Out going SMTP server, User name, and Password should be provided by
your network administrator or MIS.
• Alert Condition: You can select the abnormalities or warnings to be notified
by email. When any of the alert conditions occur, an email will be sent to
the recipients (To/Cc).
Click the Save button to the save settings.
Using Your Projector
115
Password Setting
Use Password Setting to set up an administrator password to access the Web
Management. When enabling password for the first time, set the password before
enabling it. When the password function is enabled, the administrator password
will be required for accessing the Web Management.
•
New Password: Enter new password
•
Confirm Password: Enter password again and submit
•
Write Community: Set security for SNMP. Enter password and submit.
NOTE: Contact Dell if you forget your administrator password.
116
Using Your Projector
Login Page
•
Administrator Password: Enter the Administrator Password and click Login.
Using Your Projector
117
Firmware Upgrade
Use the Firmware Update page to update your projector’s firmware. Press Update
to start.
•
118
Please wait till the count reaches 0.
Using Your Projector
•
Wait for 3 seconds and it will proceed to the next step automatically.
•
Select the file to upgrade and click the Upgrade button. When upgrading is
in progress, the Cancel button is disabled.
Using Your Projector
119
•
Please wait till the count reaches 0.
• When upgrade is complete, please click the Re Login button to go back to
the Web Management Home Page.
Crestron
For Crestron function.
120
Using Your Projector
FAQS:
I would like to remotely access
the projector via the Internet.
What is the best setting for the
browser?
To have the best setting for the browser, please
follow the below steps:
1 Open Control Panel
Internet Options
General tab
Temporary Internet
Files
Settings
Select Every visit to
the pages.
2 Some firewall or anti-virus may block the
HTTP application. If possible, turn off the
firewall or anti-virus.
I would like to remotely access The following are the TCP/IP socket ports
the projector via Internet. What which the projector uses.
socket port number should I
UDP/TCP
Port
Description
open for it in the firewall?
Number
Why am I unable to access the
projector via the Internet?
TCP
80
Web configuration
(HTTP)
UDP/TCP
25
SMTP: used for email
routing between mail
servers
UDP/TCP
161
SNMP: Simple
Network
Management
Protocol
UDP
9131
AMX: used for AMX
discovery
1 Check whether your computer/laptop is
connected to the Internet.
2 Check with your MIS or network
administrator whether your
computer/laptop is in the same subnet.
Using Your Projector
121
Why am I unable to access the
SMTP server?
Why am I unable to receive the
test alert email even though the
projector already indicates the
test mail is already sent?
122
Using Your Projector
1 Check with your MIS or network
administrator whether the SMTP server
function is open for the projector and the
IP assigned to the projector is allowed to
access the SMTP server. The projector’s
SMTP socket port number is 25, this
cannot be changed.
2 Check if the outgoing SMTP server, user
name, and password are set correctly.
3 Some SMTP servers will check whether the
mail address of "From" correlates with the
"User name" and "Password". For example,
you use test@dell.com as the mail address
in "From". You should also use
test@dell.com account information for the
User name and the password to log in the
SMTP server.
It could be because the SMTP server
recognized the alert mail as a spam mail or
because of the SMTP server restriction. Check
with your MIS or network administrator for
the SMTP server’s setting.
Firewall Configuration and FAQ
Q: Why can’t I access the Web Management Page?
A: Your computer’s firewall configuration may prevent you from accessing the
Web Management Web Page. Please refer to the following configuration
settings:
Firewall Protection
McAfee Security
Center
Norton AntiVirus
Sygate Personal
Firewall
Configuration
1
Launch McAfee Security Center (Start > All
Programs > McAfee > McAfee Security Center).
2
On the personal firewall plus tab, click View the
Internet Applications List.
3
Find and select Dell S320 or S320wi Projector
from the list.
4
Right-click on its Permissions column.
5
Select Allow Full Access from the pop-up menu.
1
Open Norton AntiVirus (Start > All Programs >
Norton AntiVirus > Norton AntiVirus).
2
Click Options menu, then select Norton
AntiVirus.
3
On the Status page, select Internet Worm
Protection.
4
Find and select Dell S320 or S320wi Projector
from the list of programs.
5
Right-click on its Internet Access column.
6
Select Permit All from the pop-up menu.
7
Click OK.
1
Open Sygate Personal Firewall (Start > All
Programs > Sygate > Sygate Personal Firewall).
2
From the Running Applications list, find and
right-click on Dell S320 or S320wi Projector.
3
Select Allow from the pop-up menu.
Using Your Projector
123
Firewall Protection
Windows Firewall
Zone Alarm
124
Configuration
1
Open Windows Firewall (Start > All Programs >
Control Panel). Double-click on Windows
Firewall.
2
On the General tab, uncheck Don’t allow
exceptions.
3
On the Exceptions tab, click the Add Program...
button.
4
Find and select Dell S320 or S320wi Projector
from the list of programs, then click OK.
5
Click OK to confirm exceptions settings.
1
Open Zone Alarm Firewall (Start > All Programs
> Zone Labs > Zone Labs Center).
2
On the Program Control page, find and select
Dell S320 or S320wi Projector from the list.
3
Right-click on its Access-Trusted column.
4
Select Allow from the pop-up menu.
5
Right-click and select Allow for the
Access-Internet, Server-Trusted, and ServerInternet columns.
Using Your Projector
Make Application Token
The Application Token lets you perform Plug and Show using a USB token.
NOTE: This is only application to S320wi or a wireless-enabled S320.
1
From the application software, click
2
The following screen appears. Click Next.
3
Plug a flash drive into any of the USB ports on your computer. Select the
drive from the list, then click Next.
4
Click Finish to close the wizard.
> Make Application Token.
Using Your Projector
125
Troubleshooting Your Projector
4
If you experience problems with your projector, see the following troubleshooting
tips. If the problem persists, contact Dell™ (see Contacting Dell™ on page 144).
Problem
Possible Solution
No image appears on the
screen
• Ensure that you have chosen the correct
input source on the INPUT SOURCE
menu.
• Ensure the external graphics port is
enabled. If you are using a Dell™ laptop
(Fn+F8). For
computer, press
other computers, see your respective
documentation. If images are not displayed
properly, please upgrade the video driver of
your computer. For Dell computers, see
support.dell.com.
• Ensure that all the cables are securely
connected. See "Connecting Your
Projector" on page 13.
• Ensure that the pins of the connectors are
not bent or broken.
• Ensure that the lamp is securely installed
(see "Changing the Lamp" on page 134).
• Use Test Pattern in the Projector Settings
of the Advanced Settings menu. Ensure
that the colors of the test pattern are
correct.
F8
CRT/LCD
Fn
126
Troubleshooting Your Projector
Problem (continued)
Partial, scrolling, or
incorrectly displayed image
Possible Solution (continued)
1 Press the Auto Adjust button on the
remote control or the control panel.
2 If you are using a Dell™ laptop computer,
set the resolution of the computer to
WXGA (1280 x 800):
a Right-click the unused portion of your
Microsoft® Windows® desktop, click
Properties, and then select Settings tab.
b Verify that the setting is 1280 x 800 pixels
for the external monitor port.
c Press
(Fn+F8).
If you experience difficulty in changing
resolutions, or if your monitor freezes, restart
all the equipment and the projector.
If you are not using a Dell™ laptop computer,
see your documentation. If images are not
displayed properly, please upgrade the video
driver of your computer. For a Dell computer,
see support.dell.com.
The screen does not display
your presentation
If you are using a portable computer, press
(Fn+F8).
Image is unstable or flickering Adjust the tracking in the OSD Display
Settings of the Advanced Settings menu (in
PC Mode only).
Image has vertical flickering
bar
Adjust the frequency in the OSD Display
Settings of the Advanced Settings menu (in
PC Mode only).
Image color is incorrect
• If the display receives the wrong signal
output from the graphics card, please set
the signal type to RGB in the OSD Image
Settings of the Advanced Settings tab.
• Use Test Pattern in the Projector Settings
of the Advanced Settings menu. Ensure
that the colors of the test pattern are
correct.
Troubleshooting Your Projector
127
Problem (continued)
Image is out of focus
Possible Solution (continued)
1 Adjust the focus ring on the projector lens.
2 Ensure that the projection screen is within
the required distance from the projector
1.31 ft [0.4 m] to 12.5 ft [3.82 m].
The image is stretched when
displaying a 16:9 DVD
The projector automatically detects the input
signal format. It will maintain the aspect ratio
of the projected image according to input
signal format with an Original setting.
If the image is still stretched, adjust the aspect
ratio in the Display Settings of the Advanced
Settings menu in the OSD.
Image is reversed
Select Projector Settings of the Advanced
Settings from the OSD and adjust the
projector mode.
Lamp is burned out or makes When the lamp reaches its end of life, it may
a popping sound
burn out and may make a loud popping sound.
If this occurs, the projector does not turn back
on. To replace the lamp, see "Changing the
Lamp" on page 134.
LAMP light is solid amber
If the LAMP light is solid amber, replace the
lamp.
LAMP light is blinking amber If the LAMP light is blinking amber, the lamp
module connection may be disrupted. Please
check the lamp module and ensure that it is
properly installed.
If the LAMP lights and the Power light are
blinking amber, the lamp driver has failed and
the projector will automatically shut down.
If the LAMP and TEMP lights are blinking
amber and the Power light is solid blue, the
color wheel has failed and the projector will
automatically shut down.
To clear the protection mode, press and hold
the POWER button for 10 seconds.
128
Troubleshooting Your Projector
Problem (continued)
Possible Solution (continued)
TEMP light is solid amber
The projector has overheated. The display
automatically shuts down. Turn the display on
again after the projector cools down. If the
problem persists, contact Dell™.
TEMP light is blinking amber If the projector fan fails, the projector will
automatically shut down. Try to clear the
projector mode by pressing and holding the
Power button for 10 seconds. Please wait for
about 5 minutes and try to power up again. If
the problem persists, contact Dell™.
The OSD does not appear on
the screen
Try to press the Menu button on the panel for
15 seconds to unlock the OSD. Check the
Menu Lock on page 65.
The remote control is not
operating smoothly or works
only within a limited range
The battery may be low. If so, replace with two
new AAA batteries.
Troubleshooting Your Projector
129
Troubleshooting your Interactive Pen
Problem (continued)
Possible Solution (continued)
Cannot use the Pen or cannot
connect the Pen
• Check if the input source is PC (VGA,
HDMI, Wireless and LAN source)
• Check if the Interactive function is turned
On. (Menu -> Advanced Settings ->
Interactive Settings -> Interactive)
• Check if the Connection option is set
correctly. (Menu -> Advanced Settings ->
Interactive Settings -> Connection)
• When using Wireless or LAN connection,
and the Pen does not work,check if the
Wireless and LAN function is turned On.
1 Menu -> Advanced Settings -> LAN
Settings -> Wireless and LAN
2 Menu -> Advanced Settings -> Wireless Settings -> Wireless
• When using Wireless or LAN connection,
check if Dell Wireless Application Software
is connected. (Only support full screen
mode output).
• Check if Lens is facing towards the screen.
• Push any key to wake up (except Nib
button).
The LED does not work.
Check if the battery is depleted.
The Amber LED is
continuously lit
The battery is low, charging the Interactive
Pen battery.
The Green LED is
continuously lit, but the
cursor does not move, and the
projector screen displays
"USB connection is not
detected".
Check the mini USB cable connection
between your computer and your S320wi
projector.
Cannot select Interactive
Check if there is a PC (VGA, HDMI, Wireless
and LAN source) input source.
130
Troubleshooting Your Projector
Cannot use the Pen in 3D
source.
a
Supports the VGA and HDMI output
signal at 120 Hz only.
b Composite/S-Video output signal at 60 Hz
and Component output signal are not
supported.
Cannot use the Pen in
Composite Video or S-Video
source.
Composite Video or S-Video source is not supported.
Cannot use Nib
If the Nib is worn out, replace with a new Nib.
When using USB Display, can
Wireless USB function be used?
Wireless USB function is not supported.
Troubleshooting Your Projector
131
Guiding Signals
Control Buttons
Projector
Status
Description
Indicator
Power
TEMP
(Amber)
LAMP
(Amber)
Standby mode
Projector in Standby mode. Ready to
power on.
BLUE
Flashing
OFF
OFF
Warming up
mode
Projector takes some time to warm up
and power on.
BLUE
OFF
OFF
Lamp on
Projector in Normal mode, ready to
display an image.
Note: The OSD menu is not
accessed.
BLUE
OFF
OFF
Cooling mode
Projector is cooling to shutdown.
BLUE
OFF
OFF
Cooling before
Power Saving
mode
The projector takes 60 seconds to cool
down before entering Power Saving
mode.
AMBER
OFF
OFF
Projector
overheated
Air vents might be blocked or ambient
temperature may be above 35 ºC. The
projector automatically shuts down.
Ensure that the air vents are not blocked
and that the ambient temperature is
within operational range. If the problem
persists, contact Dell.
OFF
AMBER
OFF
The lamp driver is overheated. The air
vents may be blocked. The projector
automatically shuts down. Turn the
display on again after the projector cools
down. If the problem persists, contact
Dell.
AMBER
AMBER
OFF
Fan breakdown
One of the fans has failed. The projector
automatically shuts down. If the problem
persists, contact Dell.
OFF
AMBER
Flashing
OFF
Lamp driver
breakdown
The lamp driver has failed. The projector
automatically shuts down. Unplug the
power cord after three minutes and then
turn the display on again. If this problem
persists, contact Dell.
AMBER
Flashing
OFF
AMBER
Flashing
Color Wheel
breakdown
Color wheel cannot start. The projector
has failed and the projector
automatically shuts down. Unplug the
power cord after three minutes and then
turn on the projector. If this problem
persists, contact Dell.
BLUE
AMBER
Flashing
AMBER
Flashing
Lamp failure
Lamp is defective. Replace the lamp.
OFF
OFF
AMBER
Fault - DC
supply (+12V)
Power supply has been interrupted. The
projector automatically shuts down.
Unplug the power cord after three
minutes and then turn on the projector.
If this problem persists, contact Dell.
AMBER
Flashing
AMBER
AMBER
Lamp module
connection
failed
Lamp module connection may be
disrupted. Check the lamp module and
ensure that it is properly installed. If the
problem persists, contact Dell.
OFF
OFF
AMBER
Flashing
Lamp driver
overheated
132
Troubleshooting Your Projector
Interactive Pen LED Guiding Signals
PEN Status
Description
Normal Mode 1 Pen faces the screen with
the link.
Normal Mode 2 Pen doesn’t faces the screen
but with the link.
Search for
Open network
mode
When Pen searching for
open network (Green LED
flashing twice every 2 sec).
After holding down Nib and
Function button for 5 secs,
the pen will change to this
mode.
Search for Fixed When Pen searching for
network mode fixed network.
Pairing mode
Pair successful
mode
After holding down
Function button for 5 secs,
the Green LED will blink 1
time each 0.15 secs
(continued 10 seconds).
When pen pair with
projector successfully after
pairing mode (Green and
Amber LED will flash
alternately continued 3
seconds).
Pair failed mode When pen pair with
projector failed after pairing
mode (Green and Amber
LED will flash at the same
time continued 3 seconds).
Sleep mode
Indicator
Green color
Amber color
Solid ON
OFF
Flashing 0.02s
ON /1s OFF
OFF
Will enter Sleep Mode after 3
minutes
Flashing 0.1s
ON /0.1s OFF
& 0.1s ON/1.7s
OFF
OFF
If the pen doesn't pair with projector
successfully, the pen will enter Sleep
Mode after 3 minutes
Flashing 0.3s
ON /0.3s OFF
OFF
If the pen doesn't pair with projector
successfully, the pen will enter Sleep
Mode after 3 minutes
Flashing 0.15s
ON /0.15s OFF
OFF
If the pen pair with projector
successfully, the pen will enter Pair
successful mode.
If the pen doesn't pair with projector
successfully, the pen will enter Pair
failed mode after 10 seconds.
Flashing 0.3s
ON /0.3s OFF
Flashing 0.3s
OFF/0.3s ON
Enter pairing mode and pair
successfully in 10 seconds
Flashing 0.3s
ON /0.3s OFF
Flashing 0.3s
ON /0.3s OFF
Enter pairing mode and pair failed
after 10 seconds
Solid ON 3 sec.
1. Pen doesn't face the screen but
with the link: will enter Sleep mode
after 3 minutes.
Solid ON 3 sec.
2. After searching for AP channel 3
cycles without a link, will enter Sleep
mode.
Enter sleep mode for power
saving purpose.
Low battery
capability
The pen battery is low. Two
hours are left to run out of
the battery.
Battery is
exhausted and
can not run PB
The Photo sensor and RF
module cannot work
properly. Pen can not work
normal.
Battery
charging when
battery low
Battery
charging when
battery full
Checking flow and items / times
OFF
Flashing 1s
ON/1s OFF
OFF
Solid ON
Pen put on the charger or
connect USB cable by
Laptop
N/A
Solid ON
Pen put on the charger or
connect USB cable by
Laptop
N/A
OFF
The MSP430 will check battery
capacity in normal operation. This
alert LED signal is shown if the
battery capacity is low.
The pen battery is exhausted. Power
only works for MSP430. The alert
LED will appear 1 minute to save
power and then enter Sleep mode.
Pen cannot be used in this status.
Troubleshooting Your Projector
133
Changing the Lamp
CAUTION: Before you begin any of the procedures in this section, follow the
Safety Instructions as described on page 11.
Replace the lamp when the message "Lamp is approaching the end of its
useful life in the operation. Replacement suggested!
www.dell.com/lamps" appears on the screen. If this problem persists after
replacing the lamp, contact Dell™. For more information, see Contacting Dell™on
page 144.
CAUTION: Use an original lamp to ensure safe and optimal working condition
of your projector.
CAUTION: The lamp becomes very hot when in use. Do not attempt to replace
the lamp until the projector has been allowed to cool down for at least
30 minutes.
CAUTION: Do not touch the bulb or the lamp glass at any time. Projector
lamps are very fragile and may shatter if touched. The shattered glass pieces
are sharp and can cause injury.
CAUTION: If the lamp shatters, remove all broken pieces from the projector
and dispose or recycle according to state, local, or federal law. For more
information see www.dell.com/hg.
1 Turn off the projector and disconnect the power cord.
2 Let the projector cool for at least 30 minutes.
3 Loosen the two screws that secure
the lamp cover, and remove the cover.
4 Loosen the two screws that secure
the lamp.
5 Pull the lamp up by its metal handle.
NOTE: Dell™ may require lamps replaced under warranty to be returned to Dell™. Otherwise,
contact your local waste disposal agency for the address of the
nearest deposit site.
6 Replace with the new lamp.
7 Tighten the two screws that secure the lamp.
8 Replace the lamp cover and tighten the two screws.
134
Troubleshooting Your Projector
9 Reset the lamp usage time by selecting "Yes" for Lamp Reset in the OSD Power
Settings of the Advanced Setting menu (see Power Settings of the Advanced
Setting menu on page 67). When a new lamp module has been changed, the
projector will automatically detect and reset the lamp hours.
CAUTION: Lamp Disposal (for the US only)
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE
RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE, OR FEDERAL
LAWS. FOR MORE INFORMATION, GO TO WWW.DELL.COM/HG OR CONTACT
THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG. FOR
LAMP-SPECIFIC DISPOSAL INFORMATION, CHECK
WWW.LAMPRECYCLE.ORG.
Troubleshooting Your Projector
135
Specifications
Light Valve
0.55" XGA S450 DMD, DarkChip3™
Brightness
3000 ANSI Lumens (Max.)
Contrast Ratio
2200:1 Typical (Full On/Full Off)
Uniformity
80% Typical (Japan Standard - JBMA)
Number of Pixels
1024 x 768 (XGA)
Aspect Ratio
4:3
Displayable Color
1.07 billion colors
Color Wheel Speed
2 X
5
1 X for 3D Display
Projection Lens
F-Stop: F/ 2.8
Effective Focal length=7.26 mm
Fixed Lens, Digital Zoom only
Throw ratio =0.626 wide and tele
Offset Ratio
115±5%
Projection Screen Size
31.45 ~ 300 inches (diagonal)
Projection Distance
1.31 ft ~ 12.5 ft (0.4 m ~ 3.82 m)
Video Compatibility
Composite Video / S-Video: NTSC (J, M, 4.43), PAL
(B, D, G, H, I, M, N), SECAM (B, D, G, K, K1, L)
Component Video input via VGA: 1080i, 720p,
576i/p, 480i/p
HDMI input: 1080p, 720p, 576i/p, 480i/p
Power Supply
136
Specifications
Universal AC 100-240 V 50-60 Hz with PFC input
Power Consumption
Normal mode: 305 W ± 10% @ 110 Vac
Eco mode: 225 W ± 10% @ 110 Vac
Power saving mode: <15 W (Wireless and Network
On)
Standby mode: < 0.5 W (Network Off, and
VGA_OUT Off, and Wireless Off)
Audio
1 speaker x 5 watt RMS
Noise Level
35 dB(A) Normal mode, 31 dB(A) Eco mode
Projector Weight
7 lb (3.18 kg)
Interactive Pen Weight
0.13 lb (60 g) (with Li-ion battery)
Projector Dimensions
(W x H x D)
11.3 x 3.6 x 8.7 inches (288 x 92 x 220 mm)
11
.3
"(2
88
mm
)
3.6"(92 mm)
8.7
"(
0
22
m
m
)
Interactive Pen Dimensions 0.88 x 0.94 x 6.66 inches (22.46 x 23.79 x 169.17
(W x H x D)
mm)
0.88" (2
2.46 mm
for S320wi only
)
6.
66
”
6
(1
9.
17
m
m
)
0.94"
(23.79 mm)
Specifications
137
Environmental
Operating temperature: 5 ºC - 35 ºC (41 ºF- 95 ºF)
Humidity: 80% maximum
Storage temperature: 0 ºC to 60 ºC (32 ºF to 140 ºF)
Humidity: 90% maximum
Shipping temperature: -20 ºC to 60 ºC
(-4 ºF to 140 ºF)
Humidity: 90% maximum
I/O Connectors (for
S320/S320wi)
Power: One AC power socket (3-pin - C14 inlet)
VGA input: Two 15-pin D-sub connectors (Blue),
VGA-A and VGA-B, for analog RGB/Component
input signals.
VGA output: One 15-pin D-sub connector (Black)
for VGA-A loop through.
S-Video input: One standard 4-pin min-DIN
S-Video connector for Y/C signal.
Composite Video input: One Yellow RCA jack for
CVBS signal.
HDMI input: One HDMI connector for supporting
HDMI 1.3. HDCP compliant.
Analog Audio input: One 3.5 mm stereo mini phone
jack (Blue).
Variable audio output: One 3.5 mm stereo mini
phone jack (Green).
USB (type B) port: One mini USB slave for remote
support and Interactive Pen.
RS232 port: One 9-pin D-sub for RS232
communication.
USB (type A) port (embedded for S320wi): One
USB connector for Photo/PtG viewer (JPG/PPT
format).
USB (type B) port (embedded for S320wi): One
USB connector for supporting USB display.
RJ45 port (embedded for S320wi): One RJ45
connector for control of projector through network
and LAN display.
138
Specifications
Wireless Dongle
(embedded for S320wi)
Wireless Standard: IEEE802.11b/g/n
Wireless: One WiFi USB (type A) connector for
supporting wireless dongle (Embedded WiFi, USB
interface).
OS environment: Windows 7/Vista/XP/2000, MAC OS X
Support: Presentation slides and projector control.
Allow connection up to 30 users at the same time.
4-to-1 split screen. Allows four presentation slides to be projected on screen.
Conference Control mode.
Supports Audio Projection (driver installation may be required. Download from support.dell.com).
Lamp
Philips 240 W user-replaceable lamp
Lamp life
Without image care
Normal mode: Up to 3000 hours
ECO mode: Up to 4000 hours
With image care
Normal mode: Up to 4000 hours
ECO mode: Up to 5000 hours
NOTE: The lamp life rating for any projector is a measure of brightness
degradation only, and is not a specification for the time it takes a lamp to fail
and cease light output. Lamp life is defined as the time it takes for more than
50 percent of a lamp sample population to have brightness decrease by
approximately 50 percent of the rated lumens for the specified lamp. The lamp
life rating is not guaranteed in any way. The actual operating life span of a
projector lamp will vary according to operating conditions and usage patterns.
Usage of a projector in stressful conditions which may include dusty
environments, under high temperatures, many hours per day, and abrupt
powering-off will most likely result in a lamp’s shortened operating life span or
possible lamp failure.
Specifications
139
NOTE: All optical performance is measured under the condition of the
Interactive Pen off within user manual or product specification.
140
Specifications
RS232 Pin Assignment
RS232 Protocol
•
Communication Settings
Connection settings
Value
Baud Rate
19,200
Data Bits
8
Parity
None
Stop Bits
1
•
Command types
To pop up the OSD menu and adjust the settings.
•
Control command Syntax (From PC to Projector)
[H][AC][SoP][CRC][ID][SoM][COMMAND]
•
Example: Power ON Command (Send low byte firstly)
•
Control Commands List
--> 0xBE, 0xEF, 0x10, 0x05, 0x00, 0xC6, 0xFF, 0x11, 0x11, 0x01, 0x00, 0x01
To view the latest RS232 code, go to the Dell Support site at support.dell.com.
To view the latest SNMP commands and list, go to the Dell Support site at
support.dell.com.
Specifications
141
Compatibility Modes (Analog/Digital)
142
Resolution
Refresh Rate (Hz)
Hsync Frequency
(KHz)
Pixel Clock (MHz)
640 x 350
70.087
31.469
25.175
640 x 480
59.940
31.469
25.175
640 x 480 p60
59.940
31.469
25.175
720 x 480 p60
59.940
31.469
27.000
720 x 576 p50
50.000
31.250
27.000
720 x 400
70.087
31.469
28.322
640 x 480
75.000
37.500
31.500
848 x 480
60.000
31.020
33.750
640 x 480
85.008
43.269
36.000
800 x 600
60.317
37.879
40.000
800 x 600
75.000
46.875
49.500
800 x 600
85.061
53.674
56.250
1024 x 768
60.004
48.363
65.000
1280 x 720 p50
50.000
37.500
74.250
1280 x 720 p60
60.000
45.000
74.250
1920 x 1080 i50
50.000
28.125
74.250
1920 x 1080 i60
60.000
33.750
74.250
1280 x 720
59.855
44.772
74.500
1024 x 768
75.029
60.023
78.750
1280 x 800
59.810
49.702
83.500
1366 x 768
59.790
47.712
85.500
1360 x 768
60.015
47.712
85.500
1024 x 768
84.997
68.677
94.500
1440 x 900
59.887
55.935
106.500
1152 x 864
75.000
67.500
108.000
1280 x 960
60.000
60.000
108.000
1280 x 1024
60.020
63.981
108.000
1152 x 864
85.000
77.095
119.651
1400 x 1050
59.978
65.317
121.750
1280 X 800
84.880
71.554
122.500
1280 x 1024
75.025
79.976
135.000
1440 X 900
74.984
70.635
136.750
1680 x 1050
59.954
65.290
146.250
1280 x 960
85.002
85.938
148.500
1920 x 1080
60.000
67.500
148.500
1400 X 1050
74.867
82.278
156.000
1280 x 1024
85.024
91.146
157.000
1440 X 900
84.842
80.430
157.000
1600 x 1200
60.000
75.000
162.000
Specifications
800 x 600
119.972
76.302
73.250
1024 x 768
119.989
97.551
115.500
1280 x 720
120.000
101.563
146.250
NOTE: The refresh rate of the timings at 120 Hz (gray area) can supported in 3D
mode.
Specifications
143
Contacting Dell
For customers in the United States, call 800-WWW-DELL (800-999­
3355).
NOTE: If you do not have an active Internet connection, you can find contact
information on your purchase invoice, packing slip, bill, or Dell product catalog.
Dell™ provides several online and telephone-based support and service
options. Availability varies by country and product, and some services may
not be available in your area. To contact Dell for sales, technical support,
or customer service issues:
1
Visit Support.dell.com.
2
Verify your country or region in the Choose A Country/Region drop-
down menu at the bottom of the page. 3
Click Contact Us on the left side of the page.
4
Select the appropriate service or support link based on your need.
5
Choose the method of contacting Dell that is convenient for you.
144
Contacting Dell
Contacting eInstruction
eInstuction provides phone based and online technical support options.
Availability varies by country, but an e-mail to
techsupport@einstruction.com can be directed appropriately for users in
any country.
USA eInstruction Software Technical Support
Phone: 480-443-2214 or 800-856-0732
Email: Techsupport@einstruction.com
International eInstruction Software Technical Support, EMEA
Phone: +33 1 58 31 1065
Email: EU.Support@einstruction.com
Web-based Technical Support is available at:
www.einstruction.com (in US)
www.einstruction.de (in Germany)
www.einstruction.fr (in France)
www.einstruction.it (in Italy)
www.einstruction.es (in Spain)
Contacting Dell
145
Contacting Crestron
Crestron provides phone based and online technical support options.
Availability varies by country, but an e-mail to
getroomview@crestron.com can be directed appropriately for users in any
country.
Technical Support
In the US and Canada
Phone: 877-516-5394
Email: roomviewsupport@crestron.com
Outside the US and Canada
Phone: +1 201-367-1037
Email: roomviewsupport@crestron.com
146
Contacting Dell
Appendix: Glossary
ANSI Lumens — A standard for measuring the brightness. It is calculated by
dividing a square meter image into nine equal rectangles, measuring the lux (or
brightness) reading at the center of each rectangle, and averaging these nine
points.
Aspect Ratio — The most popular aspect ratio is 4:3 (4 by 3). Early television and
computer video formats are in a 4:3 aspect ratio, which means that the width of
the image is 4/3 times the height.
Brightness — The amount of light emitted from a display or projection display or
projection device. The brightness of projector is measured by ANSI lumens.
Color Temperature — The color appearance of white light. Low color
temperature implies warmer (more yellow/red) light while high color temperature
implies a colder (more blue) light. The standard unit for color temperature is
Kelvin (K).
Component Video — A method of delivering quality video in a format that
consists of the luminance signal and two separate chrominance signals and are
defined as Y'Pb'Pr' for analog component and Y'Cb'Cr' for digital component.
Component video is available on DVD players.
Composite Video — A video signal that combines the luma (brightness), chroma
(color), burst (color reference), and sync (horizontal and vertical synchronizing
signals) into a signal waveform carried on a single wire pair. There are three kinds
of formats, namely, NTSC, PAL, and SECAM.
Compressed Resolution — If the input images are of higher resolution than the
native resolution of the projector, the resulting image will be scaled to fit the
native resolution of the projector. The nature of compression in a digital device
means that some image content is lost.
Contrast Ratio — Range of light and dark values in a picture, or the ratio between
their maximum and minimum values. There are two methods used by the
projection industry to measure the ratio:
1 Full On/Off — measures the ratio of the light output of an all white image (full
on) and the light output of an all black (full off) image.
2 ANSI — measures a pattern of 16 alternating black and white rectangles. The
average light output from the white rectangles is divided by the average light
output of the black rectangles to determine the ANSI contrast ratio.
Full On/Off contrast is always a larger number than ANSI contrast for the same
projector.
Glossary
147
dB — decibel — A unit used to express relative difference in power or intensity,
usually between two acoustic or electric signals, equal to ten times the common
logarithm of the ratio of the two levels.
Diagonal Screen — A method of measuring the size of a screen or a projected
image. It measures from one corner to the opposite corner. A 9 FT high, 12 FT
wide, screen has a diagonal of 15 FT. This document assumes that the diagonal
dimensions are for the traditional 4:3 ratio of a computer image as per the example
above.
DHCP — Dynamic Host Configuration Protocol — A network protocol that
enables a server to automatically assign a TCP/IP address to a device.
DLP® — Digital Light Processing™ — Reflective display technology developed by
Texas Instruments, using small manipulated mirrors. Light passing through a color
filter is sent to the DLP mirrors which arrange the RGB colors into a picture
projected onto screen, also known as DMD.
DMD — Digital Micro-Mirror Device — Each DMD consists of thousands of
tilting, microscopic aluminum alloy mirrors mounted on a hidden yoke.
DNS — Domain Name System — An Internet service that translates domain
names into IP addresses.
Focal Length — The distance from the surface of a lens to its focal point.
Frequency — It is the rate of repetition in cycles per seconds of electrical signals.
Measured in Hz (Hertz).
HDCP — High-Bandwidth Digital-Content Protection — A specification
developed by Intel™ Corporation to protect digital entertainment across digital
interface, such as DVI, HDMI.
HDMI — High-Definition Multimedia Interface — HDMI carries both
uncompressed high definition video along with digital audio and device control
data in a single connector.
Hz (Hertz) — Unit of frequency.
IEEE802.11 — A set of standards for wireless local are network (WLAN)
communication. 802.11b/g/n uses the 2.4 GHz band.
Keystone Correction — Device that will correct an image of the distortion
(usually a wide-top narrow-bottom effect) of a projected image caused by
improper projector to screen angle.
Maximum Distance — The distance from a screen the projector can be to cast an
image that is usable (bright enough) in a fully darkened room.
Maximum Image Size — The largest image a projector can throw in a darkened
room. This is usually limited by focal range of the optics.
148
Glossary
Minimum Distance — The closest position that a projector can focus an image
onto a screen.
NTSC — National Television Standards Committee. North American standard for
video and broadcasting, with a video format of 525 lines at 30 frames per second.
PAL — Phase Alternating Line. A European broadcast standard for video and
broadcasting, with a video format of 625 lines at 25 frames per second.
Reverse Image — Feature that allows you to flip the image horizontally. When
used in a normal forward projection environment text, graphics, etc. are
backwards. Reverse image is used for rear projection.
RGB — Red, Green, Blue — typically used to describe a monitor that requires
separate signals for each of the three colors.
S-Video — A video transmission standard that uses a 4-pin mini-DIN connector
to send video information on two signal wires called luminance (brightness, Y) and
chrominance (color, C). S-Video is also referred to as Y/C.
SECAM — A French and international broadcast standard for video and
broadcasting, closely related to PAL but with a different method of sending color
information.
SSID — Service Set Identifiers — A name used to identify the particular wireless
LAN to which a user wants to connect.
SVGA — Super Video Graphics Array — 800 x 600 pixels count.
SXGA — Super Extended Graphics Array, — 1280 x 1024 pixels count.
UXGA — Ultra Extended Graphics Array — 1600 x 1200 pixels count.
VGA — Video Graphics Array — 640 x 480 pixels count.
WEP — Wired Equivalent Privacy — This is a method for encrypting
communication data. The encryption key is created and notified only to the
communicating user, so the communication data cannot be decrypted by a third
party.
XGA — Extended Video Graphics Array — 1024 x 768 pixels count.
WXGA — Wide Extended Graphics Array — 1280 x 800 pixels count.
Glossary
149
Index
A
Adjusting the Projected Image 31
Adjusting the Projector Height
31
lower the projector
Tilt adjustment wheel 31
Adjusting the Projector Focus 32
Focus ring 32
C
Changing the Lamp 134
Connecting the Projector
Composite Video cable 23
Connecting a Computer with a RS232 cable 19, 20
Connecting with a Component Cable 24
Connecting with a Composite
Cable 23
Connecting with an HDMI
Cable 25
Connecting with an S-video
Cable 22
HDMI cable 25, 26, 27
Power cord 17, 18, 19, 20, 22, 23, 24, 25, 26, 27
RS232 cable 19
S-Video cable 22
To Computer 17
USB to USB cable 17
150
Index
USB-A to USB-B cable 20
VGA to VGA cable 17, 18
VGA to YPbPr cable 24
Connecting with your Interactive
Pen
Interactive Pen 28
Power cord 28
Projection Screen 28
USB-A to Mini USB-B Cable 28
VGA to VGA Cable 28
Connection Ports
Audio-B left-channel input connector 13
Audio-B right-channel input connector 13
Composite Video connector 13
HDMI connector 13
Mini USB for remote mouse, Interactive function and
Firmware upgrade. 13
RJ45 connector 13
RS232 connector 13
Security cable slot 13
S-Video connector 13
USB Type A Viewer connector 13
USB Type B Display connector
13
VGA-A input (D-sub) connector
13
VGA-A output (monitor loop-through) 13
VGA-B input (D-sub) connector
13
Contact Dell 7, 129, 134
Control Panel 35
D
Dell
contacting 144
I
Interactive Pen
Control panel 11
Firmware upgrade connector 11
LED indicators 11
Mini USB charge connector 11
Photo sensor 11
Power switch 11
Replaceable nib 11
Wrist strap holder 11
O
On-Screen Display 51
ADVANCED SETTINGS 55
AUDIO INPUT 54
AUTO ADJUST 52
BRIGHTNESS/CONTRAST 53
HELP 73
INPUT SOURCE 51
INPUT SOURCE MULTIPLE DISPLAY 52
LANGUAGE 72
Main Menu 51
VIDEO MODE 53
VOLUME 54
P
phone numbers 144
Powering On/Off the Projector
Powering Off the Projector 30
Powering On the Projector 30
M
Main Unit 10
5W speaker 10
Control panel 10
Focus tab 10
IR receivers 10
Lens 10
Lens cap 10
Lens cover 10
Tilt adjustment wheel 10
R
Remote Control 37
IR receiver 36
S
Specifications
Audio 137
Brightness 136
Color Wheel Speed 136
Contrast Ratio 136
Dimensions 137
Index
151
Displayable Color 136
Environmental 138
I/O Connectors 138
Light Valve 136
Noise Level 137
Number of Pixels 136
Power Consumption 137
Power Supply 136
Projection Distance 136
Projection Lens 136
Projection Screen Size 136
RS232 Protocol 141
Uniformity 136
Video Compatibility 136
Weight 137
support
contacting Dell 144
T
telephone numbers 144
Troubleshooting 126
Contact Dell 126
152
Index