MULTIMEDIA PROJECTOR
Table of Contents
Safety Instructions
Before Use
Projecting an Image
User’s Manual
User’s Manual /
Installation
Manual
Useful Functions Available
During a Presentation
Setting Functions from Menus
Installation
Installation Manual
Connecting to a Network
Maintenance
Appendix
Appendix
Index
ENG
How to Use This Manual
Thank you for purchasing a Canon projector.
The WUX5000 / WUX4000 / WX6000 / SX6000 Multimedia Projector (hereinafter referred
to as “the projector”) is a high-performance projector that is capable of projecting a highresolution computer screen and high-quality digital image on a large screen.
User’s Manual (Operation) / Installation Manual (Installation and Maintenance) (This Manual)
This manual combines the user’s manual and the installation manual for the WUX5000 /
WUX4000 / WX6000 / SX6000 Multimedia Projectors. The user’s manual provides information on how to use the projector. The installation manual describes how to install the projector and connect to a network, as well as perform maintenance. Read this manual
thoroughly to make the most of your projector. Installation of the projector should be performed by a qualified technician. Contact the Canon Customer Support Center for further
information.
Symbols of Button Operations
The projector can be operated using the buttons on the remote control or on the
side of the projector. The remote control allows you to operate all functions of
the projector. In this document, the button’s operations are shown as below.
Adjusting the Image Size
Operation of buttons on side of
projector
The size of the projected image can be adjusted b
remote control or the LENS button on the projector.
Change the projector installation position if your de
adjust it with the zoom function. (P155)
1
Press either the ZOOM button on the remote control
Remote control button operation
Remote control
Projector
Remote control
Push twice
Indicate the buttons to be pressed
Symbols Used in This Manual
Meanings of the symbols used in this manual are as follows.
A precaution about operation or restriction is given here.
These descriptions are for WUX5000 / WUX4000.
These descriptions are for WX6000 / SX6000.
These descriptions are for WUX4000.
These descriptions are for WX6000.
2
How to Use This Manual
COPYRIGHT NOTICE
Please note that enlarging or reducing the size of an image for commercial purposes or public presentation may infringe on the legally protected copyright or the
copyright holder of the original material.
About Trademarks
• Ethernet is a registered trademark of Xerox Corporation.
• Microsoft, Windows, Windows XP, Windows Vista and Windows 7 are registered
trademarks or trademarks of Microsoft Corporation in the United States and / or
other countries.
• Mac, Mac OS and Macintosh are trademarks of Apple Inc., registered in the United
States and / or other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing, LLC.
• PJLink is a registered trademark, or an application has been submitted for trademark, in Japan, the United States and / or other countries or regions.
3
Quick Reference Guide
This Quick Reference Guide will help you find functions that make full use of the projector
and are useful for producing an attractive presentation, etc.
Connecting the Projector
Changing the Remote Control Channel
(P124)
Connecting to the Computer (P47 - P51)
Connecting to AV Equipment (P52 - P55)
Resetting Projector Setting
Projecting an Image
Resetting Password (P128)
Initializing the Network Setting (P176)
Resetting to the Default Setting (P140)
Starting Projection (P56 - P58)
Selecting an Input Signal (P59 - P60)
Adjusting the Image
Miscellaneous Functions
Adjusting the Image Size and Focus (P71 P73)
Adjusting Keystone Distortion (P76)
Adjusting Aspect Ratio (P63 - P70)
Eliminating Flickers from Computer Screen
and Adjusting Positional Shift (P96, P97)
Using the Power Saving Mode (P120)
Turning on the Projector by Connecting the
Power Cord (P121)
Disabling the Beep During Operation (P122)
Disabling Buttons (P123)
Hiding Guide Messages (P126)
Setting a Password (P128)
Adjusting Colors and Image Quality
Reducing the Lamp Brightness (P119)
Projecting an Image on a Greenboard (P103)
Selecting an Image Mode Suitable for the
Projecting Image (P109)
Making Fine Color Adjustments (P114)
Removing Noise (P116)
Displaying Test Pattern (P138)
Selecting Audio In Terminal (P139)
Producing a Presentation
Temporarily Blacking Out an Image (P82)
Freezing the Picture (P82)
Adjusting the Volume (P83)
Muting the Sound (P83)
Zooming an Image (P84)
Showing the Elapsed Time (P85)
4
Table of Contents
How to Use This Manual ..............................................................................................2
Safety Instructions .....................................................................................................12
Safety Precautions.................................................................................................................... 13
CAUTION ON HANGING FROM THE CEILING ...................................................................... 13
■ READ AND KEEP THIS OWNER’S MANUAL FOR LATER USE. ..................................... 14
AC Power Cord Requirement ................................................................................................... 16
Federal Communication Commission Notice............................................................................ 17
Canadian Radio Interference Regulations ................................................................................ 17
Precautions for Use .................................................................................................................. 18
Precautions for Installation ....................................................................................................... 19
Precautions on the lamp ........................................................................................................... 21
Precautions for the batteries of the remote control ................................................................... 22
Before Use ........................................................................................................ 25
Supplied Accessories ................................................................................................26
■ Installing Remote Control Batteries ................................................................................. 27
Preparing the Remote Control ..................................................................................29
■ Remote Control Operating Range ................................................................................... 29
■ When a remote control is connected using a cable (WX6000 / SX6000)........................ 30
Part Names..................................................................................................................31
Main Unit (The illustration shows WUX5000.) .......................................................................... 31
■ Front Side ........................................................................................................................ 31
■ Rear Side ......................................................................................................................... 32
■ Bottom Side ..................................................................................................................... 32
Remote Control......................................................................................................................... 34
■ RS-RC04 .......................................................................................................................... 34
■ RS-RC05 .......................................................................................................................... 36
Side Control .............................................................................................................................. 38
■ LED Indicator Displays .................................................................................................... 39
Input Terminal ........................................................................................................................... 40
User’s Manual (Operation) ............................. 43
Projecting an Image ......................................................................................... 45
Steps for Connecting the Projector and Projecting an Image ...............................46
Connecting the Projector ..........................................................................................47
Connecting the Projector to a Computer .................................................................................. 47
■ Connecting to RGB Monitor Output Terminal (Analog Connection)................................ 47
■ Connecting to DVI Monitor Output Terminal (Digital Connection)................................... 50
■ Connecting with a HDMI Cable (Input signal type: [HDMI] – P59) ................................. 51
■ Outputting Audio to Speakers ......................................................................................... 51
5
Table of Contents
Quick Reference Guide................................................................................................4
Table of Contents
Connecting to AV Equipment ................................................................................................... 52
■ Connecting to Digital Video Output Terminal (Digital Connection) ................................ 52
■ Connecting to Analog Video Output Terminal (Analog Connection) .............................. 53
■ Outputting Audio to Speakers......................................................................................... 55
Starting Projection ..................................................................................................... 56
■ When the Language Selection Screen Appears............................................................. 57
■ When the Password Input Screen Appears.................................................................... 58
■ When “No signal” Appears ............................................................................................. 58
■ When Notebook Computer Screen Does Not Appear .................................................... 58
■ Adjusting Image.............................................................................................................. 58
Changing Notebook Computer Screen Output......................................................................... 58
■ Turning on External Monitor Output ................................................................................ 58
Selecting an Input Signal (INPUT) ............................................................................ 59
■ Types of Input Signals .................................................................................................... 59
■ Selecting an Input Signal ................................................................................................ 60
Adjusting the Image................................................................................................... 61
Setting the Display Resolution of the Computer....................................................................... 61
■ Windows 7....................................................................................................................... 61
■ Windows Vista................................................................................................................. 61
■ Windows XP .................................................................................................................... 61
■ Mac OS X ........................................................................................................................ 62
AUTO PC ................................................................................................................................. 62
■ Performing the Auto PC Function.................................................................................... 62
Selecting Screen Aspect and Aspect ....................................................................................... 63
■ Selecting Screen Aspect ................................................................................................ 63
■ Selecting Aspect Ratio.................................................................................................... 69
Adjusting the Image Size.......................................................................................................... 71
Adjusting the Focus.................................................................................................................. 73
Adjusting the Image Position.................................................................................................... 74
■ Resetting the Position ..................................................................................................... 75
Adjusting Keystone Distortion .................................................................................................. 76
■ Resetting the Keystone Adjustment................................................................................ 77
Selecting an Image Mode .......................................................................................... 78
■ Image Modes .................................................................................................................. 78
■ How to Select an Image Mode........................................................................................ 79
Turning Off the Projector .......................................................................................... 80
Useful Functions Available During a Presentation ....................................... 81
Useful Functions Available During a Presentation................................................. 82
Temporarily Blacking Out an Image ...................................................... BLANK ...................... 82
Freezing the Picture .............................................................................. FREEZE.................... 82
Adjusting the Volume ............................................................................ VOL........................... 83
Muting the Sound .................................................................................. MUTE........................ 83
Zooming an Image ................................................................................ D.ZOOM.................... 84
Showing the Elapsed Time (WUX5000 / WUX4000) ............................ P-TIMER ................... 85
6
Table of Contents
Setting Functions from Menus........................................................................ 87
■ Menu Configuration ......................................................................................................... 88
■ Basic Menu Operations ................................................................................................... 90
Setting Display Status ...............................................................................................93
Selecting an Image Projection Mode ........................................................................................ 93
Automatic Display Adjustment (WX6000 / SX6000) ................................................................. 94
Selecting an Input Signal Type (Analog PC) ............................................................................ 94
Selecting an Input Signal Type (Component) (WUX5000 / WUX4000) .................................... 95
Adjust Input Signal Type (Analog PC) Total Dots ..................................................................... 95
Adjust Input Signal Type (Analog PC) Tracking ....................................................................... 96
Adjust Input Signal Type (Analog PC) Horizontal Position ....................................................... 96
Adjust Input Signal Type (Analog PC) Vertical Position ........................................................... 97
Adjust Input Signal Type (Analog PC) Horizontal Pixels .......................................................... 97
Adjust Input Signal Type (Analog PC) Vertical Pixels............................................................... 98
Selecting HDMI Input Level ...................................................................................................... 98
HDMI Color Format................................................................................................................... 99
Select HDMI Over Scan.......................................................................................................... 100
Performing Progressive Processing ....................................................................................... 101
Selecting a Menu Position ......................................................................................................102
Correcting the Screen Color ................................................................................................... 103
Reversing Projection............................................................................................................... 104
No Signal Screen.................................................................................................................... 105
Screen When Blank ................................................................................................................ 106
Selecting a Logo at Startup .................................................................................................... 106
Selecting Aspect Ratio of Screen ........................................................................................... 107
Adjusting Keystone Distortion (WX6000 / SX6000) ................................................................ 108
Image Shift Adjustment (WX6000 / SX6000).......................................................................... 108
Selecting an Image Quality......................................................................................109
Image Adjustment................................................................................................................... 109
Saving the Desired Image Quality .......................................................................................... 110
Adjusting the Brightness ......................................................................................................... 111
Adjusting the Contrast ............................................................................................................ 112
Adjusting the Sharpness ......................................................................................................... 113
Performing Gamma Correction ............................................................................................... 113
Adjusting Color ....................................................................................................................... 114
Correcting the Image According to the Ambient Light ............................................................ 115
Noise Reduction ..................................................................................................................... 116
Dynamic Gamma .................................................................................................................... 116
Memory Color Correction........................................................................................................117
6-axis Color Adjust (Detailed Color Adjustment) .................................................................... 117
Detailed Gamma Correction ................................................................................................... 118
7
Table of Contents
How to Use Menus .....................................................................................................88
Table of Contents
Reducing the Lamp Brightness (WUX4000) .......................................................................... 119
Resetting the Image Adjustment Settings .............................................................................. 119
Setting Various Functions....................................................................................... 120
Selecting the Power Management Mode ............................................................................... 120
Skip the POWER Button Operation........................................................................................ 121
Enabling / Disabling the Beep ................................................................................................ 122
Key Repeat (WX6000 / SX6000)............................................................................................ 122
Prohibiting Operations............................................................................................................ 123
Main Unit and Remote Control Channel Settings................................................................... 124
Selecting a Display Language................................................................................................ 125
Showing / Hiding the Guide Screen ....................................................................................... 126
Showing / Hiding the Input Status .......................................................................................... 127
Selecting the HDMI Input ....................................................................................................... 127
Setting a Password ................................................................................................................ 128
Registering a Password ......................................................................................................... 129
Prohibiting Operation of the Lens (WUX5000 / WUX4000).................................................... 130
Lens Shift Reset ..................................................................................................................... 131
Extending the Menu Display Time.......................................................................................... 132
Showing / Hiding the High Temperature Warning Icon .......................................................... 133
Reducing Flickering (WUX5000 / WUX4000)......................................................................... 134
Gamma Restore (WX6000 / SX6000) .................................................................................... 134
Lamp Warning Display (WX6000 / SX6000) .......................................................................... 135
Resetting the Lamp Counter .................................................................................................. 135
■ About the Display of the Lamp Counter........................................................................ 136
Filter Warning Display (WX6000 / SX6000) ........................................................................... 137
Resetting the Air Filter Counter (WX6000 / SX6000) ............................................................. 137
Displaying Test Pattern (WX6000 / SX6000) ......................................................................... 138
Selecting Audio In Terminal (WX6000 / SX6000) .................................................................. 139
Locking Installation Related Functions (WX6000 / SX6000).................................................. 139
Resetting to the Default Setting.............................................................................................. 140
Checking Projector Information ............................................................................. 141
Installation Manual
(Installation and Maintenance) .................... 143
Installation ...................................................................................................... 145
Installation Precautions........................................................................................... 146
Precautions When Carrying the Projector .............................................................................. 146
Installation Precautions .......................................................................................................... 146
Precautions When Carrying and Transporting the Projector.................................................. 146
■ When using mounted on the ceiling ............................................................................. 148
8
Table of Contents
■ Install facing in the correct direction ............................................................................. 148
Selecting the Projection Method and Installation Location .................................150
■ Ceiling Mounting or Rear Projection.............................................................................. 150
■ Adjusting the projection position when installed on the floor ........................................ 150
Installing / Removing the Lens Unit .......................................................................151
■ Installing the Lens Unit .................................................................................................. 151
■ Removing the Lens Unit ................................................................................................ 155
Setting Up the Projector ..........................................................................................156
■ Positioning the Projector in Front of the Screen ............................................................ 156
■ Relationship Between Image Size and Projecting Distance ......................................... 156
■ Lens Shift Function ........................................................................................................ 160
Connecting to AV Equipment..................................................................................162
■ Connectable Equipment and Input Terminals............................................................... 162
■ Connection Terminal and Connection Cable ................................................................ 164
Connecting to a Network ............................................................................... 165
Preparing the Remote Control ................................................................................166
Connection Methods ............................................................................................................... 166
Setting an IP Address ............................................................................................................. 167
■ Windows 7 ..................................................................................................................... 167
■ Windows Vista ............................................................................................................... 168
■ Windows XP................................................................................................................... 169
■ Mac OS X....................................................................................................................... 170
■ Resetting the IP Address Setting of the Computer........................................................ 170
Network Settings on the Projector .........................................................................171
Locking the Network Settings ................................................................................................. 171
Turning the Network Function On / Off ................................................................................... 172
Setting a Network Password................................................................................................... 173
Registering a Network Password............................................................................................ 173
Turning the PJLink Function On / Off ..................................................................................... 174
Turning DHCP Function On / Off ............................................................................................ 175
TCP / IP Setting ...................................................................................................................... 175
Initializing Network Settings .................................................................................................... 176
Configuring the Network From the Computer .......................................................177
■ Displaying and Configuring the Network Configuration Screen.................................... 177
■ Resetting to Factory Defaults ........................................................................................ 180
■ Setting Errors ................................................................................................................. 180
Setting Up the Network............................................................................................182
■ Setting Basic Information [Network] .............................................................................. 182
■ Setting Up Email [Mail] .................................................................................................. 183
■ Mail Authentication Settings [Mail auth] ........................................................................ 184
■ Sending a Test Mail [Send test mail]............................................................................. 185
■ SNMP Settings [SNMP] ................................................................................................. 185
■ Setting Projector Information [Projector info.]................................................................ 186
■ Setting PJLink [PJLink] .................................................................................................. 187
9
Table of Contents
Installation Procedure..............................................................................................149
Table of Contents
Controlling the Projector from a Computer........................................................... 188
Error Mail .................................................................................................................. 190
Maintenance ................................................................................................... 191
Cleaning the Projector............................................................................................. 192
Cleaning and Replacing the Air Filter .................................................................... 193
Replacing the Air Filter ........................................................................................................... 193
Cleaning the Air Filter............................................................................................................. 194
Replacing the Lamp ................................................................................................. 195
Replacement Lamp ................................................................................................................ 196
Replacing the Lamp ............................................................................................................... 196
Appendix ....................................................... 199
Appendix ......................................................................................................... 201
Troubleshooting....................................................................................................... 202
LED Indicator Meanings ......................................................................................................... 202
Symptoms and Solutions........................................................................................................ 203
■ You Cannot Turn on the Projector................................................................................. 203
■ You Cannot Project an Image from the Projector ......................................................... 203
■ There is no Sound ......................................................................................................... 204
■ The Projected Image Is Blurred .................................................................................... 205
■ You Cannot Project an Image Appropriately ................................................................ 205
■ The Projector Power Turns Off ...................................................................................... 205
■ You Cannot Operate the Remote Control ..................................................................... 206
Relationship between Aspect and Screen Aspect................................................ 207
WUX5000 / WUX4000............................................................................................................ 207
■ When the image is projected on a 16:10 screen .......................................................... 207
■ When the image is projected on a 16:9 screen ............................................................ 208
■ When the image is projected on a 4:3 screen .............................................................. 208
■ When projecting on a 16:10 screen in the aspect ratio of the connected device ........ 209
■ When projecting on a 16:9 screen in the aspect ratio of the connected device .......... 209
■ When projecting on a 4:3 screen in the aspect ratio of the connected device ............ 210
WX6000.................................................................................................................................. 210
■ When the image is projected on a 16:10 screen .......................................................... 210
■ When the image is projected on a 16:9 screen ............................................................ 211
■ When the image is projected on a 4:3 screen .............................................................. 211
■ When projecting on a 16:10 screen in the aspect ratio of the connected device ........ 212
■ When projecting on a 16:9 screen in the aspect ratio of the connected device .......... 212
■ When projecting on a 4:3 screen in the aspect ratio of the connected device ............ 213
SX6000................................................................................................................................... 213
■ When the image is projected on a 4:3 screen .............................................................. 213
■ When the image is projected on a 16:10 screen .......................................................... 214
■ When the image is projected on a 16:9 screen ............................................................ 214
■ When projecting on a 4:3 screen in the aspect ratio of the connected device ............ 215
10
Table of Contents
Displayed Test Patterns...........................................................................................217
Supported Signal Types ..........................................................................................218
Product Specifications ............................................................................................219
■ Projector ........................................................................................................................ 219
■ Remote control .............................................................................................................. 221
■ Specification of Each Lens Unit (Option) ...................................................................... 221
■ External View ................................................................................................................. 223
■ ANALOG PC (WUX5000 / WUX4000), ANALOG PC-1 (WX6000 / SX6000) /
COMPONENT IN Terminal ................................................................................................ 223
■ Service Port (CONTROL)............................................................................................... 224
Index ..........................................................................................................................228
Menu Configuration ................................................................................................232
11
Table of Contents
■ When projecting on a 16:10 screen in the aspect ratio of the connected device......... 215
■ When projecting on a 16:9 screen in the aspect ratio of the connected device........... 216
Safety Instructions
Before installing and operating the projector, read this manual thoroughly.
This projector provides many convenient features and functions. Operating the projector
properly enables you to manage those features and maintain it in good condition for
many years to come.
Improper operation may result in not only shortening the product life, but also malfunctions, fire hazards, or other accidents.
If your projector does not seem to be operating properly, read this manual again, check
operations and cable connections, and try the solutions in the “Troubleshooting” section
in the back of this manual. If the problem still persists, contact the Canon Customer Support Center.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE
EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING
AND MAINTENANCE INSTRUCTIONS FOR THIS UNIT IN THE OWNER’S
MANUAL.
CAUTION
Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer / Data Processing Equipment, ANSI / NFPA 75.
12
Safety Instructions
Safety Precautions
• This projector produces intense light from the projection lens. Do not stare directly into
the lens, otherwise eye damage could result. Be especially careful that children do not
stare directly into the beam.
• Install the projector in a proper position. Otherwise it may result in a fire hazard.
• Allowing the proper amount of space on the top, sides, and rear of the projector cabinet
is critical for proper air circulation and cooling of the unit. The diagrams shown here
indicates the minimum space required. If the projector is to be built into a compartment
or similarly enclosed, these minimum distances must be maintained.
SIDE and TOP
REAR
50 cm (1.6')
50 cm (1.6')
50 cm (1.6')
50 cm (1.6')
• Do not cover the ventilation slots on the projector. Heat build-up can reduce the service
life of your projector, and can also be dangerous.
• If the projector is unused for an extended time, unplug the projector from the power outlet.
• Do not project the same image for a long time.
An afterimage may remain on the LCD panels due to the characteristics of the panels of
the projector.
CAUTION ON HANGING FROM THE CEILING
When hanging the projector from the ceiling, clean the air intake vents and top of the projector periodically with a vacuum cleaner. If you leave the projector unclean for a long
time, the cooling fans can be clogged with dust, and it may cause a breakdown or a
disaster.
DO NOT SET THE PROJECTOR IN GREASY, WET, OR SMOKY CONDITIONS SUCH
AS IN A KITCHEN TO PREVENT A BREAKDOWN OR A DISASTER. IF THE PROJECTOR COMES IN CONTACT WITH OIL OR CHEMICALS, IT MAY BECOME DETERIORATED.
13
Safety Instructions
WARNING:
• THIS APPARATUS MUST BE GROUNDED.
• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
Safety Instructions
■READ AND KEEP THIS OWNER’S MANUAL FOR LATER USE.
All the safety and operating instructions should be read before beginning to operate the
product.
Read all of the instructions given here and retain them for later use. Unplug this projector
from the AC power supply before cleaning. Do not use liquid or aerosol cleaners on the
projector. Use a damp cloth for cleaning.
Follow all warnings and instructions marked on the projector.
For added protection of the projector during a lightning storm, or when it is left unattended or unused for long periods of time, unplug it from the wall outlet. This will prevent
damage due to lightning and power surges.
Do not expose this unit to rain or use near water... for example, in a wet basement, near a
swimming pool, etc...
Do not use attachments not recommended by the manufacturer as they may result in hazards.
Do not place this projector on an unstable cart, stand, or table. The projector may fall,
causing serious injury to a child or adult, and serious damage to the projector. Use only
with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or
shelf mounting should be carried out in accordance with the manufacturer’s directions,
and should use a mounting kit approved by the manufacturers.
An appliance and cart combination should be moved with care.
Sudden stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
Slots and openings in the rear and front of the cabinet are provided for
ventilation, to insure reliable operation of the equipment and to protect
it from overheating.
The openings should never be covered with cloth or other materials, and the bottom
opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.
This projector should not be placed in a built-in installation such as a book case unless
proper ventilation is provided.
14
Safety Instructions
Never push objects of any kind into this projector through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind onto the projector.
Do not install the projector near the ventilation duct of air-conditioning equipment.
Do not overload wall outlets and extension cords as this can result in fire or electric shock.
Do not allow anything to rest on the power cord. Do not locate this projector where the
cord may be damaged by people walking on it.
Do not attempt to service this projector yourself as opening or removing covers may
expose you to dangerous voltages or other hazards. Refer all servicing to qualified service personnel.
Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally after following the operating instructions.
Adjust only those controls that are covered in the operating instructions as improper
adjustment of other controls may result in damage and will often require extensive work
by a qualified technician to restore the projector to normal operating condition.
e. If the projector has been dropped or the cabinet has been damaged.
f. When the projector exhibits a distinct change in performance-this indicates a need for
servicing.
When replacement parts are required, be sure the service technician uses replacement
parts specified by the manufacturer that have the same characteristics as the original
parts. Unauthorized substitutions may result in fire, electric shock, or injury.
Upon completion of any service or repairs to this projector, ask the service technician to
perform routine safety checks to determine that the projector is in safe operating condition.
15
Safety Instructions
This projector should be operated using only the type of power source indicated on the
marking label. If you are not sure of the type of power supplied, contact the Canon Customer Support Center or local power company.
Safety Instructions
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirements for use in the
country you purchased it.
AC Power Cord for the United States and Canada:
The AC Power Cord used in the United States and Canada is
listed by the Underwriters Laboratories (UL) and certified by the
Canadian Standard Association (CSA).
The AC Power Cord has a grounding-type AC line plug. This is a
safety feature to ensure the plug fits into the power outlet. Do not
try to tamper with this safety feature. Should you be unable to
insert the plug into the outlet, contact your electrician.
Ground
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
NOTE FOR CUSTOMERS IN THE US
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED
OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.
European Union (and EEA) only.
These symbols indicate that this product is not to be disposed of with
your household waste, according to the WEEE Directive (2002/96/EC),
the Battery Directive (2006/66/EC) and / or your national laws implementing those Directives. If a chemical symbol is printed beneath the
symbol shown above, in accordance with the Battery Directive, this
indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb =
Lead) is present in this battery or accumulator at a concentration above
an applicable threshold specified in the Battery Directive. This product
should be handed over to a designated collection point, e.g., on an
authorized one-for-one basis when you buy a new similar product or to
an authorized collection site for recycling waste electrical and electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste could have a possible impact on the
environment and human health due to potentially hazardous substances that are generally associated with EEE. Your cooperation in the
correct disposal of this product will contribute to the effective usage of
natural resources. For more information about the recycling of this
product, please contact your local city office, waste authority, approved
scheme or your household waste disposal service or visit
www.canon-europe.com/environment.
(EEA: Norway, Iceland and Liechtenstein)
16
Safety Instructions
Federal Communication Commission Notice
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
The cable with a ferrite core provided with the projector must be used with this equipment in order to comply with Class B limits in Subpart B of Part 15 of the FCC rules.
Use of a shielded cable is required to comply with class B limits in Subpart B of Part 15
of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified
in the instructions. If such changes or modifications should be made, you could be
required to stop operation of the equipment.
Canon U.S.A. Inc.
One Canon Plaza, Lake Success, NY 11042-1198, U.S.A.
Tel No. (516) 328-5600
Canadian Radio Interference Regulations
This Class B digital apparatus complies with Canadian ICES-003.
17
Safety Instructions
Multimedia Projector, Model: WUX5000 / WUX4000 / WX6000 / SX6000
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Safety Instructions
Precautions for Use
As this section contains important safety-related information, be sure to read the following
carefully beforehand in order to use your projector correctly and safely.
Warning
If the following situations occur, turn the power off, remove the power plug from the
power outlet and contact the Canon Customer Support Center. Failure to do so could
cause a fire or result in an electric shock.
•
•
•
•
•
•
If smoke is emitted
If an unusual smell or noise is emitted
If a loud noise is heard and the lamp turns off
If water or other liquid has entered the projector
If metal or any other foreign material has entered the projector
If the projector is knocked over or dropped and the cabinet is damaged
Warning
Pay attention to the following points for handling the power cord. Failing to pay attention to these points could cause a fire, electric shock or personal injury.
• Do not place any objects on the power cord and do not allow it to become trapped
under the projector. The power cord may be damaged.
• Do not cover the power cord with a carpet.
• Do not excessively bend, twist, pull or make modifications to the power cord.
• Keep the power cord away from heaters and other sources of heat.
• Do not use the power cord when it is bent finely, coiled or bundled.
• Do not use a damaged power cord. If your power cord is damaged, contact the
Canon Customer Support Center.
• Do not use any power cord other than the type that is included with this projector.
• Be sure to connect the ground wire of the power cord to ground. Failure to do so
could result in an electric shock.
• Be sure to connect the ground wire before connecting the power plug to the outlet.
Also when you disconnect the ground wire, be sure to unplug the power plug from
the outlet beforehand.
18
Safety Instructions
Warning
• Do not use any power source with a voltage other than the voltage indicated (AC 100
– 240 V).
• Do not pull the power cord and be sure to hold the power plug or connector when
removing. The cord could be damaged as a result.
• Do not insert any metal objects into the contact parts of the power plug or connector.
• Remove the power plug from the outlet before performing cleaning or maintenance
of the projector.
• Do not remove the power plug or connector with wet hands.
• Insert the power plug and connector securely up to the base. Additionally, do not
use a damaged power plug or an outlet that is loose.
• If using an extension cord attached to the outlet, make sure that the total electric
power consumption of connected devices does not exceed the rated capacity.
• Periodically inspect the power plug and outlet and remove any dust or dirt from
between the plug and the outlet.
Precautions for Installation
Warning
Pay attention to the following points regarding installation and handling of the projector.
Failure to do so may cause a fire, electric shock or personal injury.
• Do not use the projector in a bathroom or shower room.
• Do not use the projector in rain or snow, by the sea, or in close proximity to a body of
water.
• Do not place containers containing a liquid on top of the projector.
• Do not place the projector in any location where it will be exposed to oily smoke or
steam, such as a kitchen work surface or table etc.
• Do not touch the projector itself, the power cord, or the cable if lightening strikes.
19
Safety Instructions
Pay attention to the following points regarding the power source, power plug and handling of the connector. Failure to do so could result in a fire, electric shock or personal
injury.
Safety Instructions
Warning
Pay attention to the following points regarding installation and handling of the projector.
Failure to do so may cause a fire, electric shock or personal injury.
• Do not move the projector until you have switched off the power, removed the power
plug from the power outlet and unplugged any other cables.
• Before installing or replacing a lens unit, make sure to remove the power plug from
the outlet. Failure to do so could result in an electric shock or injury.
• Do not remove the cabinet from the projector or disassemble it. The interior of the
projector contains high-voltage components as well as parts that are hot. These
could cause an electric shock or burn. If inspection, maintenance or repair is
required, contact the Canon Customer Support Center.
• Do not disassemble or modify the projector (including consumable parts) or the
remote control.
• Do not insert any object into vents in the projector, such as the air intake vent or
exhaust vents.
• Do not place a pressurized can in front of the exhaust vents. The pressure of the
contents of the can may increase due to heat from the exhaust vents and this could
result in an explosion.
• As strong light beams are emitted while the projector is in use, do not look directly
into the projector lens. Doing so could cause an eye injury. Pay particular attention in
preventing young children to do so.
• When giving a presentation in front of the projector while it is projecting an image,
conduct your presentation from a position where your shadow will not be cast on the
screen and where you do not feel blinded by light from the projector.
Caution
Pay attention to the following points regarding installation and handling of the projector.
• If the projector will not be used for a long period of time, be sure to remove the
power plug from the power outlet to ensure safety. Failure to do so could cause a
fire.
• The temperature of the cabinet around and above the exhaust vents can become hot
during projector operation. Touching these areas during operation could cause
burns to the hands.
Do not touch these areas. Doing so may cause burns. Pay particular attention in preventing young children from touching these parts. Additionally, do not place any
metal objects on these areas. Due to the heat from the projector, doing so could
cause an accident or personal injury.
20
Safety Instructions
Caution
Pay attention to the following points regarding installation and handling of the projector.
Precautions on the lamp
Warning
When replacing the lamp, or when the lamp is damaged, pay attention to the following
points. Failure to do so could result in an electric shock or personal injury.
• Be sure to remove the power plug from the power outlet before replacing the lamp.
• When the lamp is damaged, shards of glass may be scattered inside the projector.
Contact the Canon Customer Support Center for cleaning and inspection of the projector interior and lamp replacement.
21
Safety Instructions
• Do not place any heavy objects on top of the projector or sit / stand on it. Pay particular attention to prevent small children from doing so. The projector may be knocked
over and this could result in damage or a personal injury.
• Do not place the projector on an unstable or slanted surface. Doing so may cause
the projector to fall or be knocked over and could result in a personal injury.
• Do not place any objects in front of the lens while the projector is operating. Doing so
could cause a fire.
• When cleaning off dust or dirt from the projector lens etc., do not use any kind of
spray that is flammable. As the temperature of the lamp inside the projector is high, it
could ignite, causing a fire.
• Using the lens shift function the lens in the projector moves up / down / left / right
powered by a motor. Do not touch the lens when the lens is moving. Doing so could
cause a personal injury.
• Before replacing the lens unit, wait at least one hour after the projector is turned off
to allow the projector to cool thoroughly. Failure to do so could result in a burn or
injury.
• If the projector is used for a long period of time, dust could accumulate inside the
projector. This could cause a fire or malfunction. It is recommended that periodic
maintenance of the projector be performed. For details of maintenance costs, contact the Canon Customer Support Center.
• When hanging the projector from a ceiling, put the projector down on the floor or a
workbench before attaching or replacing the lens unit. Failure to do so could result in
parts falling off the projector and may cause an accident or personal injury.
Safety Instructions
Caution
When handling the lamp, pay attention to the following points.
• Be sure not to handle the lamp immediately after it has been used. Be sure to switch
off the power and wait for approximately 1 hour for the lamp and the projector to cool
down sufficiently. Failure to do so could result in a burn or personal injury due to heat
from the lamp or projector.
• When an instruction to replace the lamp has been displayed (LAMP Indicator Displays (P39)), the possibility of the lamp breaking will increase. Replace the lamp with
a new one as soon as possible.
• If the lamp is damaged, gas inside the lamp (containing mercury) and dust may be
emitted from the exhaust vents. If this happens, immediately open the windows and
doors to provide ventilation to the room. If you inhale any gas emitted from the lamp
or it has come into contact with your eyes or mouth, consult a doctor immediately.
• When disposing of a used mercury lamp, dispose of it in the same way as a fluorescent lamp and in accordance with the local regulations where you live.
Precautions for the batteries of the remote control
Warning
Pay attention to the following points regarding handling of batteries. Failure to do so
could result in a fire or injury.
• Do not place the batteries in a fire or apply heat to, short circuit or disassemble the
batteries.
• Do not attempt to recharge the batteries that are included with the remote control.
• Remove the batteries when they have been fully used, or if they will not be used for a
long period of time.
• When replacing the batteries, replace both at the same time. Also, do not use two
batteries of a different type at the same time.
• Insert the batteries in the correct + / - positions.
• If any liquid leaks from the batteries and comes into contact with skin, wash off thoroughly with water.
22
Safety Instructions
For Safe Use
Pay attention to the following points when carrying or transporting the projector.
23
Safety Instructions
• This projector is a precision instrument. Do not knock it over or subject it to impacts.
Doing so may cause a malfunction.
• When carrying or holding up the projector after attaching the lens unit, be sure not to
hold the lens. Doing so may cause damage to the lens unit.
• Do not reuse any packaging or shock-absorbent materials that were supplied with
the projector at the time of purchase for transporting or shipping the projector. Protection of the projector cannot be guaranteed if used packaging or shock-absorbent
materials are reused. Fragments from shock-absorbent material may also enter the
interior of the projector which could cause a malfunction.
• If transportation is necessary, the lens unit should be removed before transporting
the projector. If the projector is subjected to excessive impacts during transportation, the lens unit may be damaged. Removal and installation of the lens unit should
not be performed by the user. Be sure to have the procedure performed by a qualified technician or contact the Canon Customer Support Center.
Safety Instructions
For Safe Use
Pay attention to the following points when installing or using the projector.
• Be sure to install the projector in a location where the air intake and exhaust vents
are separated from the wall by more than 50 cm (1.6'). Failure to do so could cause
a malfunction.
• Do not install the projector in a location that is damp, or where there is a lot of dust,
oily smoke or tobacco smoke. Doing so could cause contamination of optical components such as the lens and the mirror and may result in deterioration of image
quality.
• Do not touch the lens with bare hands. Doing so may result in deterioration of image
quality.
• If the projector is suddenly moved from a location where the temperature is low to a
location where the temperature is high, or if the temperature in the location where the
projector is installed increases suddenly, moisture in the air could cause condensation to form on the projector lens or mirror. This may cause a blurred image. Wait until
the condensation has evaporated for the image projected to return to normal.
• Do not install the projector in a location where the temperature is high or low. Doing
so may cause a malfunction.
Operating temperature: 5°C to 35°C Humidity level: up to 85%
Storage temperature: -10°C to 60°C
• Do not install the projector near high-voltage electrical power lines or an electrical
power source.
• Do not use the projector on a soft surface such as carpet or sponge mat, etc. Doing
so could cause heat to build up inside the projector and this could result in a malfunction.
• Do not block the air intake or exhaust vents of the cooling fan. Doing so could cause
heat to build up inside the projector and may cause a malfunction.
• Installing the projector in the wrong direction may cause a malfunction or accident.
Install the projector so that the left / right incline is within 10°.
• Do not place any objects on top of the projector that may change shape or color due
to heat.
• When using the projector at altitudes greater than 2,300 m, or for projecting
upward / downward:
When using the projector at altitudes greater than 2,300 m, or for upward projection or downward projection, it is necessary to change the settings of the
projector. For further details, contact the Canon Customer Support Center.
24
Table of Contents
Safety Instructions
Before Use
Before Use
Projecting an Image
User’s Manual
Useful Functions Available
During a Presentation
Setting Functions from Menus
Installation Manual
Installation
Connecting to a Network
Maintenance
Appendix
Appendix
Index
25
Supplied Accessories
Check that the following accessories have been supplied with the projector.
 Remote control
(part No.: RS-RC04)
(part No.: RS-RC05)
 Batteries for the remote control
(AAA size x2)
(AA size x2)
 Power cord (1.8 m)
 VGA cable (1.8 m) for connection
to a computer (part No.: YH7-2307)
For Continental Eu(mini D-sub 15-pin / mini D-sub 15-pin)
rope
For the U.S.A. and
Canada
 User’s Manual /
Installation Manual (CD-ROM)
 Warranty Card
 Important Information
26
Supplied Accessories
■Installing Remote Control Batteries
Open the battery compartment lid.
Slide the lid while
pressing it down.
1
Open the battery compartment lid.
Raise the battery
cover tab while pushing it.
2
Insert batteries.
Insert 2 new AAA batteries in the compartment with the + and –
poles positioned correctly.
3
Close the compartment lid.
Slide the lid until you
hear a click to
securely close it.
Insert batteries.
Insert 2 new AA batteries in the compartment with the + and –
poles positioned correctly.
3
Close the compartment lid.
Insert the tab into the
remote control notch
(1) and push the battery cover down (2).
Before Use
1
2
(1)
(2)
• If buttons on the remote control are inoperative when you attempt to operate the projector,
replace the batteries with new ones.
• Do not drop the remote control or subject it to impact.
• Do not spill any liquids on the remote controller. Doing so could damage it.
27
Supplied Accessories
Pay attention to the following points when handling the batteries. Failing to do so could result in a fire or personal
injury.
• Do not heat, short circuit or disassemble the batteries, or
place them in a fire.
• Do not attempt to recharge the batteries that are included
with the remote control.
• Remove the batteries when they are flat or when the
remote control will not be used for a long period of time.
• When replacing the batteries, replace both batteries at the
same time and do not use two batteries of a different type
together.
• Insert the batteries with the + and - terminals in the correct
directions.
• If any liquid from inside the batteries leaks out and contacts your skin, be sure to wash the liquid off thoroughly.
28
Preparing the Remote Control
■Remote Control Operating Range
The remote control is an infrared type. Point it at the infrared remote receiver on the front
or rear of the projector to operate it.
(26.3')
• Use the remote control within a distance of approximately 8 m (26.3') from the projector.
• Use the remote control within an angle of 25° in any direction from directly in front of the
infrared remote receiver.
• The remote control may be inoperative if there is an obstacle between the remote control
and main unit or the infrared remote receiver on the main unit is exposed to direct sunlight
or strong light of lighting equipment.
• When you use 2 or more projectors at the same time, you can change the channel settings to prevent the 2 remote controls from interfering with each other. (P124)
29
Before Use
(26.3')
Preparing the Remote Control
■When a remote control is connected using a cable (WX6000 / SX6000)
The remote control for WX6000 / SX6000 (RS-RC05) can be used connected to the projector with a cable.
Use a cable with a Ø3.5 mm stereo mini jack (not included).
Terminal for
wired remote
control
Ø3.5 mm stereo mini jack cable
(not included)
• Infrared operations cannot be performed if a cable is connected to the projector or the
remote control.
• Use a cable with a Ø3.5 mm stereo mini jack (not included) with a length of 30 m or less.
30
Part Names
Main Unit (The illustration shows WUX5000.)
■Front Side
Power cord connector (P56)
Side control (P38)
Before Use
Lens unit
Air intake vent
Do not block the air intake.
Doing so may cause a malfunction.
Terminals
and connectors
Infrared remote receiver (P29)
Air filter (P193)
Anti-theft lock hole
An anti-theft wire cable (not included) can be
connected.
31
Part Names
■Rear Side
Exhaust vent
Do not block the air exhaust.
Doing so may cause a malfunction.
Lamp cover
Infrared remote receiver (P29)
■Bottom Side
Screw holes for installation of ceiling
attachment
Adjustable feet (P150)
32
Part Names
• Make sure to use the optional ceiling attachment.
• You should never install the ceiling
attachment by yourself.
If you mount the projector on the ceiling, you have to invert the projected
image by selecting [Image flip H/V]
from the menu. (P104)
33
Before Use
Mounting the Projector on the Ceiling
You can mount the projector on the ceiling.
The ceiling attachment (part No.: RS-CL11)
is required in order to mount the projector on
the ceiling. Depending on the installation
environment, an extension pipe (part No.:
RS-CL08 or RS-CL09) may also be required.
Contact the Canon Customer Support Center
for more detailed information.
Part Names
Remote Control
The projector can be operated using buttons on the remote control or the side control on
the main unit. The RS-RC04 remote control is included with WUX5000 / WUX4000 and the
RS-RC05 remote control is included with WX6000 / SX6000.
The remote control allows you to operate all functions of the projector.
■RS-RC04
POWER button (P56, P80)
Turns the projector on or off.
FOCUS button (P73)
Adjusts focusing.
[ ] / [ ] buttons: Moves the focus position farther away.
[ ] / [ ] buttons: Moves the focus position nearer.
ASPECT button (P70)
Changes the aspect ratio mode.
D.SHIFT/KEYSTONE button (P76)
Corrects keystone distortion.
[ ], [ ], [ ] / [ ] buttons: For keystone
adjustment.
Press D.SHIFT/KEYSTONE to correct
keystone distortion.
• Moves the image up, down, left, or right
when the screen aspect setting is [16:9
D. image shift] or [4:3 D. image shift] is
selected. (P67, P68)
• To move the image, use the [ ] / [ ] or
the [ ] / [ ] buttons.
D. ZOOM button (P84)
Zooms the image in or out digitally.
[+] button: Zooms the image in (up to 12x).
– button: Zooms the image out (1x mini[+]
mum).
[ ], [ ], [ ] / [ ] buttons: Move the zoomin location.
FREEZE button (P82)
Freezes the projected image.
IMAGE button (P79)
Switches the image mode (image quality).
34
Part Names
LENS-SHIFT button (P74)
Moves the lens up, down, left, or right.
[ ], [ ], [ ] / [ ] buttons: Move the lens.
ZOOM button (P71)
Adjusts the image size.
[ ] / [ ] buttons: Increase the image size.
[ ] / [ ] buttons: Decrease the image size.
AUTO PC button (P62)
Adjusts tracking etc. automatically in accordance with the signal from
a computer when the analog PC input is selected.
OK button (P92)
Confirms the item selected from the menu.
Pointer buttons (P90)
Selects the upper, lower, left or right item in the menu
and performs remote control channel settings. (P127)
MENU button (P88)
Displays the menu on the screen and performs remote control
channel settings.
VOL button (P83)
Adjusts the sound volume.
P-TIMER button (P85)
[+] button: Increases the volume.
Displays the time elapsed since this
– button: Decreases the volume.
[+]
button was pressed.
MUTE button (P83)
Mutes the sound.
BLANK button (P82)
Toggles between display / non-display of image.
LAMP button (WUX4000) (P119)
Toggles the lamp mode between Standard
GAMMA button (P113)
and Silent.
Adjusts the gamma of the image.
[ ] button: Corrects dark parts of the image so that they are easier to see.
[ ] button: Corrects bright parts of the image so that they are easier to see.
35
Before Use
INPUT button (P60)
Switches the input signal.
Part Names
■RS-RC05
POWER button (P56, P80)
Turns the projector on or off.
ASPECT button (P70)
Changes the aspect ratio mode.
Pointer buttons (P90)
Selects the upper, lower, left or right item
in the menu. Performs remote control
channel settings when the remote control
is used via the infrared transmitter. (P124)
OK button (P92)
Determines the item selected from the menu.
ZOOM button (P71)
Adjusts the image size.
[ ] / [ ] buttons: Increase the image size.
[ ] / [ ] buttons: Decrease the image size.
FOCUS button (P73)
Adjusts focusing.
[ ] / [ ] buttons: Moves the focus position further away.
[ ] / [ ] buttons: Moves the focus position nearer.
TEST PATTERN button (P138, P217)
Displays the test pattern.
D.ZOOM button (P84)
Zooms the image in or out digitally.
[1] button: Zooms the image in (up to 12x).
[4] button: Zooms the image out (1x minimum).
[ ] / [ ] / [ ] / [ ] buttons: Move the zoom-in
location.
Ch button (P124)
Changes the remote control channel when
the remote control is used via the infrared
transmitter.
IMAGE button (P79)
Switches the image mode (image quality).
36
Part Names
AUTO PC button (P62)
Adjusts tracking etc. automatically in accordance with the signal from a computer when the analog PC input is selected.
INPUT button (P60)
Switches the input signal.
MENU button (P89)
Displays the menu on the screen. Performs remote control channel settings
when the remote control is used via the infrared transmitter. (P127)
EXIT button (P92)
Cancels functions such as menu
SHIFT button (P74)
display or test pattern during operMoves the lens up, down, left or right.
ation and returns to the image dis[ ] / [ ] / [ ] / [ ] buttons: Move the lens. play.
KEYSTONE button (P76)
Corrects keystone distortion.
To move the image, use the [ ] / [ ] or [ ] / [ ] buttons.
VOL button (P83)
Adjusts the sound volume.
[3] button: Increases the volume.
[6] button: Decreases the volume.
MUTE button (P83)
Mutes the sound.
Numerical buttons (P129, P173, P175)
Enter password and TCP/IP setting values.
BLANK button (P82)
Toggles between display / non-display of
the image.
Fn button
Cannot be used on this
product.
FREEZE button (P82)
Freezes the projected image.
Terminal for wired remote control (P30)
Connects a cable to the projector for remote control operation.
37
Before Use
Change input buttons (P60)
Change the input signal between Digital
PC, Analog PC-1, Analog PC-2, HDMI
and Component.
Part Names
Side Control
(1) LED indicators (P39)
The projector status is shown by the LED indicators (off / on / flashing).
For indicator status, refer to page 39.
• POWER ON (green): Lights up or flashes when the power is on.
• STAND BY (red)
: Lights up or flashes during standby or when the projector is
shut down.
• WARNING (red)
: Lights up or flashes when an error occurs.
• LAMP (orange)
: Flashes when the time for replacing the lamp is near. When a
lamp cover error occurs, the [WARNING] indicator will also
flash. When a lamp error occurs, it will illuminate at the same
time as the [WARNING] indicator.
• TEMP (red)
: When the temperature inside the projector is high, it will flash. If
the temperature inside the projector increases further and a
temperature error occurs, it will illuminate at the same time that
the [WARNING] indicator illuminates.
(1)
(7)
(6)
(4)
(5)
(3)
(2)
(2) POWER button (P56, P80)
Turns the projector on or off.
(5) INPUT button (P60)
Switches the input signal.
(3) MENU button (P88, P89)
Displays a menu on the screen.
(6) Pointer / VOL buttons (P90)
Adjust the sound volume.
[ ] button: Decreases the volume.
[ ] button: Increases the volume.
Selects the upper, lower, left or right
item in the menu.
(4) LENS button
Each time the button is pressed, the
screen changes to focus adjustment
(P73), zoom (image size) adjustment
(P71), or lens shift (image position)
adjustment (P74). To adjust, use the
[ ] / [ ] or the [ ] / [ ] buttons.
38
(7) OK button (P92)
Determines the item selected from the
menu.
Part Names
■LED Indicator Displays
The LED indicators flash or illuminate to indicate the operating status of the projector.
: Off
: Lit
: Flashing
LED indicator
POWER
ON
(green)
STAND BY
(red)
WARNING (red)
LAMP
(orange)
TEMP
(red)
Operating status
Ready to turn power on (standby).
Power is on.
Power-saving mode engaged.
*
*
The time for replacing the lamp is near.
Internal temperature is high.
A lamp error has occurred.
Power was turned off due to high internal temperature.
The lamp cover is open.
Another error has occurred.
* Either the [POWER ON] or [STAND BY] indicator illuminates, depending on the power
status.
39
Before Use
Power is not connected.
Part Names
Input Terminal
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(1)LAN port (P166)
Connects the LAN cable.
Used to connect the projector to a network.
(2)ANALOG PC / COMPONENT IN terminal
(
/COMPONENT IN) (P47, P53)
Receives the analog PC signal (Analog PC).
A component cable can be used to receive the component image signal (Component).
(3)DVI-D IN terminal (
DVI-D IN) (P50)
Connects the external monitor output from a computer.
Receives the digital signal (Digital PC).
(4)HDMI IN terminal (HDMI IN) (P51)
Receives the digital content image signal (HDMI).
Carries both video and audio signals across a single cable.
(5)Service port (CONTROL)
This terminal is used by servicing technicians. It is not used during ordinary use.
(6)AUDIO IN terminal (AUDIO IN) (P47, P50, P53)
Receives the audio input corresponding to 2 image input systems other than HDMI IN.
The internal speaker outputs the audio for the selected image signal.
(7)AUDIO OUT terminal ( AUDIO OUT) (P51, P55)
Outputs the audio to external AV equipment. This outputs the audio signal that corresponds to the projected image signal.
40
Part Names
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(2)ANALOG PC-1 / COMPONENT IN terminal
(
/COMPONENT IN) (P47, P53)
Receives the analog PC signal (Analog PC-1).
A component cable can be used to receive the component image signal (Component).
(3)ANALOG PC- 2 / DVI-I IN terminal (
DVI-I IN) (P50)
Connects the external monitor output from a computer.
Receives the digital PC signal (Digital PC) or analog PC signal (Analog PC-2).
(4)HDMI IN terminal (HDMI IN) (P51)
Receives the digital content image signal (HDMI).
Carries both video and audio signals across a single cable.
(5)Service port (CONTROL)
This terminal is used by servicing technicians. It is not used during ordinary use.
(6)Terminal for wired remote control (REMOTE) (P30)
This terminal is used to connect the remote control using a cable.
(7)AUDIO IN terminal (AUDIO IN) (P47, P50, P53)
Receives the audio signal input for 2 kinds of image input except HDMI IN.
The internal speaker outputs the audio for the selected image signal.
(8)AUDIO OUT terminal ( AUDIO OUT) (P51, P55)
Outputs the audio to external AV equipment. This outputs the audio signal that corresponds to the projected image signal.
41
Before Use
(1)LAN port (P166)
Connects the LAN cable.
Used to connect the projector to a network.
42
MULTIMEDIA PROJECTOR
User’s Manual
(Operation)
43
44
Table of Contents
Safety Instructions
Projecting an
Image
Before Use
Projecting an Image
User’s Manual
Useful Functions Available
During a Presentation
Setting Functions from Menus
Installation
Installation Manual
Connecting to a Network
Maintenance
Appendix
Appendix
Index
45
Steps for Connecting the Projector and Projecting an Image
Installation work should be performed by a qualified technician.
Contact the Canon Customer Support Center for further information.
Connecting the Projector to Equipment (P162)
Starting Projection (P56)
Do you want to project an image from a
notebook computer?
Yes
No
For a notebook computer,
turn on the monitor output
(P58) and then proceed.
Selecting an Input Signal (P59)
Is the image projected properly?
Yes
Projection is complete.
No
Adjusting the Image (P61)
Make the following adjustments.
• Setting the Display Resolution of the Computer (P61)
• Selecting an Aspect Ratio of Projected Image (Screen aspect) and a Screen
Mode (Aspect) (P63, P69)
• Adjusting Misaligned Images or Flickering of the Screen Using the Auto PC (P62)
• Adjusting the Image Size (P71)
• Adjusting the Focus (P73)
• Adjusting the Image Position (Lens shift) (P74)
• Adjusting Keystone Distortion (P76)
Making Fine Adjustments
• Selecting an Image Mode (P78)
46
Connecting the Projector
Connecting the Projector to a Computer
Before connecting the cables, turn off both the projector and computer.
■Connecting to RGB Monitor Output Terminal (Analog Connection)
Computer
Projector
To ANALOG PC /
COMPONENT IN terminal
Monitor output
terminal
(mini D-sub 15-pin)
VGA cable (supplied)
When inputting corresponding audio
AUDIO output terminal
(AUDIO OUT)
Audio cable (not included)
47
To AUDIO IN terminal
Projecting an Image
Connecting with a VGA cable (Input signal type: [Analog PC] (WUX5000 / WUX4000),
[Analog PC-1] (WX6000 / SX6000) P59)
User’s Manual
Connect the projector to the computer.
A digital connection (P50) is recommended when projecting an image in high quality.
When using a computer with an HDMI output terminal, a digital connection (P51) can be
made using an HDMI cable.
Connecting the Projector
Computer
Projector
To ANALOG PC-1 /
COMPONENT IN terminal
Monitor output
terminal
(mini D-sub 15-pin)
VGA cable (supplied)
When inputting corresponding audio
AUDIO output terminal
(AUDIO OUT)
Audio cable (not included)
To AUDIO IN terminal
Connecting with VGA-DVI cable (Input signal type: [Analog PC-2] P59)
Computer
Projector
To ANALOG PC-2 /
DVI-I IN terminal
Monitor output
terminal
(mini D-sub 15-pin)
VGA-DVI-I cable (not included)
When inputting corresponding audio
AUDIO output terminal
(AUDIO OUT)
Audio cable (not included)
To AUDIO IN terminal
• Use a VGA cable in which all pins are connected. If the cable is a type in which all pins
are not connected, the image may not be correctly displayed.
• Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
will reduce the audio volume.
• The AUDIO IN terminal can be changed in the Audio in terminal select screen (P139).
(WX6000 / SX6000)
48
Connecting the Projector
Connecting with a BNC cable (Input signal type: [Analog PC] (WUX5000 / WUX4000),
[Analog PC-1] (WX6000 / SX6000) P59)
Mini D-sub 15-pin BNC terminal converter cable (not
included)
Mini D-sub 15-pin BNC terminal converter cable (not
included)
To ANALOG PC /
COMPONENT IN terminal
BNC cable (not included)
When inputting corresponding audio
AUDIO output terminal
(AUDIO OUT)
Computer
Audio cable (not included)
Mini D-sub 15-pin BNC terminal converter cable (not
included)
Mini D-sub 15-pin BNC terminal converter cable (not
included)
To AUDIO IN terminal
Projector
To ANALOG PC-1 /
COMPONENT IN terminal
Monitor output
terminal
(mini D-sub 15-pin)
BNC cable (not included)
When inputting corresponding audio
AUDIO output terminal
(AUDIO OUT)
Audio cable (not included)
To AUDIO IN terminal
• A signal with a dot clock higher than 162 MHz cannot be projected.
• Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
will reduce the audio volume.
• The AUDIO IN terminal can be changed in the Audio in terminal select screen (P139).
(WX6000 / SX6000)
49
Projecting an Image
Monitor output
terminal
(mini D-sub 15-pin)
User’s Manual
Projector
Computer
Connecting the Projector
■Connecting to DVI Monitor Output Terminal (Digital Connection)
Connecting with a DVI cable (Input signal type: [DVI-D] (Digital PC) – P59)
Computer
Projector
To DVI-D IN terminal
Monitor output
terminal
(DVI terminal)
DVI-D cable (not included)
When inputting corresponding sound
AUDIO output terminal
(AUDIO OUT)
Audio cable (not included)
Computer
To AUDIO IN terminal
Projector
To Analog PC-2 / DVI-I IN
terminal
Monitor output
terminal
(DVI terminal)
DVI-I cable (not included)
When inputting corresponding audio
AUDIO output terminal
(AUDIO OUT)
Audio cable (not included)
To AUDIO IN terminal
• Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
will reduce the audio volume.
• The AUDIO IN terminal can be changed in the Audio in terminal select screen (P139).
(WX6000 / SX6000)
50
Connecting the Projector
■Connecting with a HDMI Cable (Input signal type: [HDMI] – P59)
Computer
Projector
To HDMI IN terminal
User’s Manual
It is possible to output audio from the projected images to amplified speakers.
Projecting an Image
HDMI cable (not included)
Digital image
output terminal
(HDMI terminal)
* When an HDMI cable is connected, digital audio is also connected at the same
time.
■Outputting Audio to Speakers
Speaker
Projector
To AUDIO OUT terminal
RCA terminal
Audio cable (not included)
Mini jack
Audio input terminal
(AUDIO IN)
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor will
reduce the audio volume.
51
Connecting the Projector
Connecting to AV Equipment
Connect the projector and AV equipment.
The description provided here is one example. For more detailed information, refer to the
manual for the connected AV equipment.
Before connecting the cables, turn off both the projector and AV equipment.
■Connecting to Digital Video Output Terminal (Digital Connection)
Connecting with a HDMI cable (Input signal type: [HDMI] – P59)
AV equipment
Digital video
camera
Digital video output terminal
(HDMI terminal)
Projector
HDMI cable (not included)
* When an HDMI cable is connected, digital audio is also connected at the same
time.
52
To HDMI IN terminal
Connecting the Projector
■Connecting to Analog Video Output Terminal (Analog Connection)
AV equipment
Projector
RCA plug - RCA plug component cable
(not included)
D terminal
Video output terminal
Monitor output
terminal (DVI terminal)
Component cable
(not included)
D terminal plug - RCA plug component
conversion cable (not included)
DVI-D cable (not included)
When inputting corresponding audio
RCA terminal
To AUDIO IN terminal
Mini jack
AUDIO output terminal
Audio cable (not included)
53
Projecting an Image
To ANALOG PC / COMPONENT
IN terminal
RCA component
terminal
User’s Manual
Connecting with a component cable (Input signal type: [Component] – P59)
A component video signal from the AV equipment can be inputted into the projector by
connecting the component cable to the COMPONENT IN terminal of the projector.
Use a commercially available component cable (not included) that fits the terminal type of
the AV equipment to create a relay connection.
Connecting the Projector
AV equipment
Projector
RCA plug - RCA plug component cable
(not included)
To ANALOG PC-1 / COMPONENT IN terminal
RCA component
terminal
D terminal
Video output
terminal
Component cable
(not included)
D terminal plug - RCA plug component
conversion cable (not included)
When inputting corresponding audio
RCA terminal
Mini jack
AUDIO output terminal
To AUDIO IN terminal
Audio cable (not included)
• Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
will reduce the audio volume.
• The AUDIO IN terminal can be changed in the Audio in terminal select screen (P139).
(WX6000 / SX6000)
54
Connecting the Projector
■Outputting Audio to Speakers
It is possible to output audio from the projected images to AV equipment or amplified
speakers.
Speaker
User’s Manual
RCA terminal
Projecting an Image
Projector
To AUDIO OUT terminal
Audio cable (not included)
Mini jack
Audio input terminal
(AUDIO IN)
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor will
reduce the audio volume.
55
Starting Projection
1
Check the connection between the projector and the computer or AV equipment.
(P52 – P55)
2
Connect the power cord and make sure that the [STAND BY] indicator is lit (red).
Connect the ground terminal on the power plug to ground. Not
doing so could result in an electric shock. Also the computer
may suffer electromagnetic interference or be subject to poor TV
and radio reception.
•
•
Fully insert the power cord plug into the socket.
After turning off the projector, wait at least 5 minutes before turning it on again.
It may shorten the lamp life if you turn on the projector immediately after turning
it off.
• Unplug the power cord when not in use.
3
Press the POWER button.
The [POWER] indicator flashes green, and then stops flashing and remains lit.
Remote control
Projector
Remote control
The countdown window is displayed for approximately 20 seconds, and then the projection is started. Press the OK or EXIT button (WX6000 / SX6000) to make the countdown window disappear.
56
Starting Projection
4
Turn on the computer or AV equipment power.
Using the Power Saving Mode (Power Management)
When you enable the power management mode, the lamp is automatically turned
off if the projector receives no signal input for a certain period of time. (P120)
A window appears when the projector is turned on for the first time. You can select a language to be used by the projector for displaying menus and messages in the window.
Select the desired language with the pointer buttons and press the OK button.
You can change the language from the menu at a later time. (P125)
If the language selection screen is out of focus, press the FOCUS button to perform focus
adjustment. (P73)
Remote control
Projector
Remote control
An item highlighted in orange will be selected.
57
Projecting an Image
■When the Language Selection Screen Appears
User’s Manual
Changing Operations When Projector is Turned On
You can change operations when the projector is turned on as follows.
• You can turn on the projector by connecting the power cord, without pressing the
POWER button. (P121)
• You can change the countdown window. (P106)
• You can skip the countdown window. (P56)
Starting Projection
■When the Password Input Screen Appears
If you have set a password, the Password input screen appears. Enter your password.
(P128)
■When “No signal” Appears
With a notebook computer, the user must turn on the external monitor output. (P58)
Press the INPUT button to select the input signal. (P60)
■When Notebook Computer Screen Does Not Appear
Set your notebook computer to output signals to an external monitor. For more details,
refer to “Changing Notebook Computer Screen Output” below.
■Adjusting Image
• Set the display resolution of the computer to the highest resolution or the resolution
closest to that setting. (P61)
• Use the auto PC function to adjust shift in computer image or the flickering of the
screen. (P62)
• Use the ZOOM button to adjust the size of the projected image. (P71)
• Use the FOCUS button to correct the focus adjustment if necessary. (P73)
• Use the D.SHIFT/KEYSTONE button (WUX5000 / WUX4000) or KEYSTONE button
(WX6000 / SX6000) to adjust keystone correction if necessary. (P76)
• Select the aspect ratio of the projected image (screen aspect) or a screen mode
(aspect) according to the aspect ratio of the screen, type of input image signal etc.
(P63 - P70)
• Select an image mode depending on the projected image. (P78)
Changing Notebook Computer Screen Output
With a notebook computer, the user must turn on the external monitor output on the computer side.
This operation is not required for a desktop computer.
■Turning on External Monitor Output
You can turn on the external monitor output via keyboard operation.
To turn on the external monitor output with most computers, press the function key ([F1] to
[F12]) which is marked with the external monitor icon while holding down the [Fn] key.
While pushing
key
Press a key such as
or
.
• The function key you use and the method used to turn on the external monitor output vary
depending on the model. For details, see the manual for your notebook computer.
• With Windows 7, you can turn on image output by holding down the Windows logo key
and pressing the [P] key.
58
Selecting an Input Signal (INPUT)
Select the input signal in the [Input] menu when you want to project a digital PC or AV
equipment signal, or to switch between inputs when multiple computers or multiple sets
of AV equipment are connected.
Skip this step if you have not changed the input signal since the last projection.
The table below shows the relationship among input signals supported by the projector,
input terminals and connection cables.
Input
signal
Supported
projectors
HDMI
WUX5000
WUX4000
WX6000
SX6000
Analog
PC-2
HDMI cable (not included)
WUX5000
WUX4000
DVI cable (not included)
WX6000
SX6000
WUX5000
WUX4000
WX6000
SX6000
Analog
PC
Analog
PC-1
Types of connection cables
Projecting an Image
Digital
PC
Input terminal
/
COMPONENT IN
VGA cable (supplied)
BNC cable (not included)
WUX5000
WUX4000
WX6000
SX6000
/
COMPONENT IN
Mini D-sub 15-pin - BNC
terminal converter cable
(not included)
BNC cable
(not included)
VGA-DVI cable (not included)
WX6000
SX6000
Component cable (not included)
Component
WUX5000
WUX4000
WX6000
SX6000
D terminal plug - RCA plug
component conversion cable (not included)
/
COMPONENT IN
RCA plug - RCA plug component cable (not included)
59
User’s Manual
■Types of Input Signals
Selecting an Input Signal (INPUT)
■Selecting an Input Signal
1
Press the INPUT button to display the window shown below.
Remote control
Projector
Remote control
The currently active input signal is marked with a circle and highlighted in orange.
An input signal that is ready for projection is displayed in white. When no signal is
received, it is displayed in gray. However [HDMI] and [DVI-D] (WUX5000 / WUX4000)
(Digital PC), or [Digital PC] (WX6000 / SX6000) may be displayed in gray even if they
are ready for projection.
2
You can switch the available input signal types by pressing the INPUT button.
• You can select the target input signal with [ ] / [ ].
• Only the input signals displayed in white can be selected.
3
Press the OK button to confirm the input signal type.
Change the input signal with the input signal buttons. (WX6000 / SX6000)
For WX6000 / SX6000, you can also switch to the input signal you want by pressing
the button that corresponds to that signal.
Remote control
60
Adjusting the Image
Setting the Display Resolution of the Computer
Based on the maximum resolution of the projector, set the display resolution of the computer to the resolution closest to the output signal resolution of the projector. (P218)
User’s Manual
Maximum resolution
WUX5000 / WUX4000: 1920 X 1200 dots
SX6000: 1400 X 1050 dots
WX6000: 1440 X 900 dots
■Windows 7
Open the [Control Panel] from the start
menu, then select [Appearance and Personalization] - [Adjust screen resolution] in
the [Control Panel Home].
2
Click the [Resolution] tab, and move the
slider to select or the resolution closest to
the maximum output signal resolution of
the computer.
3
Click the OK button.
Projecting an Image
1
■Windows Vista
■Windows XP
1
1
Right-click on the desktop background
and select [Properties] to open the
[Display Properties].
2
Click the [Settings] tab, and under
[Screen Resolution], select the resolution closest to the maximum output
signal resolution of the computer.
3
Click the OK button.
Open the [Control Panel] from the start
menu, then select [Appearance and
Personalization] - [Adjust screen resolution] in the [Control Panel Home].
2
Select the resolution closest to the
maximum output signal resolution of
the computer from the [Resolution] list.
3
Click the OK button.
61
Adjusting the Image
■Mac OS X
1
Open the Apple Menu and select [System
Preferences].
2
In the [System Preferences] window, click
the [Displays] icon to display the Display
window.
3
Select the [Display] tab and select the resolution closest to the maximum output signal resolution of the computer from the
[Resolutions] list.
4
Close the [System Preferences] window.
AUTO PC
If the image display is shifted or there is flickering of the screen when [Analog PC]
(WUX5000 / WUX4000) or [Analog PC-1] [Analog PC-2] (WX6000 / SX6000) is selected,
press the AUTO PC button to adjust the projector to the optimal condition.
The adjustment results will be stored. If the projector is used again with the same computer, when the input signal is selected the image will be projected automatically under
the same conditions that were previously adjusted.
■Performing the Auto PC Function
Press the AUTO PC button to perform projector adjustment.
Remote control
If the projected image was not properly adjusted with the [AUTO PC] function, perform the
following steps.
• From [Input signal select], select an input signal type based on the resolution of the computer. (P94)
• If the adjustment is still insufficient, from [Input signal settings] select [Total dots], [Tracking], [Horizontal position], [Vertical position], [Horizontal pixels] and [Vertical pixels] to
make adjustments. (P95 - P98)
• For the signal types supported by the projector, see the table on page 218.
62
Adjusting the Image
Selecting Screen Aspect and Aspect
Select an optimum aspect ratio of the projected image (screen aspect) or an optimum
screen mode (aspect) according to the aspect ratio of the screen, type of input image
signal and so on for the projection to make best use of the screen size.
Select the same screen aspect ratio as the screen you are using.
In general, select [Auto].
You may need to change the setting depending on the resolution of the computer or other
AV equipment connected. If the image is not projected with the desired aspect ratio, refer
to page 207.
User’s Manual
[Screen aspect]
[Aspect]
■Selecting Screen Aspect
1
Press the MENU button to display a menu window.
Remote control
Projector
63
Remote control
Projecting an Image
Select the correct aspect ratio for the screen which is used.
Perform the following steps to select the aspect ratio of the projected image.
Adjusting the Image
2
Use the [ ] / [ ] buttons to select the [Display settings] tab (WUX5000 / WUX4000) or
[Install settings] (WX6000 / SX6000).
Remote control
3
Projector
Remote control
Select [Screen aspect] with the [ ] / [ ], and then press the OK button.
Remote control
Projector
64
Remote control
Adjusting the Image
4
Use the [ ] / [ ] buttons to select the desired contents.
Remote control
Projector
Remote control
User’s Manual
WUX5000
WUX4000
16:10
16:9
4:3
16:10 D. image shift
16:9 D. image shift
4:3 D. image shift
: Compatible
: Not compatible
65
WX6000
SX6000
Projecting an Image
Screen aspect compatibility for each model of projector is as follows.
Adjusting the Image
16:10
Select this when you use a screen with aspect ratio of
16:10. Also, select this when you project an image on
a wall. You can correct keystone distortion with this
mode. (P76)
16:9
Select this when you use a screen with aspect ratio of
16:9. You can correct keystone distortion with this
mode. (P76)
16:10 screen
16:9 screen
4:3
Select this when you use a screen with aspect ratio of
4:3. You can correct keystone distortion with this
mode. (P76)
16:10 D. image shift (SX6000)
Select when the screen aspect ratio is 16:10. Keystone correction cannot be performed in this mode.
However when projecting level, it is possible to shift
the image up or down.
For details about how to shift the image, refer to page
67.
4:3 screen
16:9 D. image shift
Select this when you use a screen with aspect ratio of 16:9. You cannot correct keystone
distortion in this mode, but you can move the image up or down with images being projected horizontally.
For the details on how to move the image, refer to page 67.
4:3 D. image shift (WUX5000 / WUX4000 / WX6000)
Select this when you use a screen with aspect ratio of 4:3.
You cannot perform the keystone adjustment in this mode; however, you can move the
image to the left or right while projecting the image horizontally.
For the details on how to move the image, refer to page 68.
5
Press the OK button to confirm your setting and then press the MENU button.
66
Adjusting the Image
Moving Image with 16:9 D. Image Shift / 16:10 D. Image Shift (SX6000)
16:10 D. image shift cannot be used for the WUX5000, WUX4000 and WX6000.
1
Remote control
2
Use the [ ] / [ ] buttons to move the image.
Remote control
Projector
Remote control
Screen
[ ] button
Moves image up
3
[ ] button
Moves image down
When the image fits the screen, press the OK button.
67
Projecting an Image
For the WX6000 / SX6000, when the screen aspect is [16:9 D. image shift], and for
the SX6000, when the screen aspect is set to [16:10 D. image shift], press the MENU
button, select the [Installation settings] tab with the [ ] and [ ] buttons, and then
select [Digital image shift] with the [ ] and [ ] buttons. (P108)
User’s Manual
For the WUX5000 / WUX4000, when the screen aspect is [16:9 D. image shift], if the
D.SHIFT/KEYSTONE button is pressed, the screen below on the right is displayed.
Adjusting the Image
Moving Image with 4:3 D. Image Shift (WUX5000 / WUX4000 / WX6000)
4:3 D image shift cannot be used for SX6000.
1
For the WUX5000 / WUX4000, when the screen aspect is [4:3 D. image shift], if the
D.SHIFT/KEYSTONE button is pressed, the screen below on the right is displayed.
Remote control
For the WX6000, when the screen aspect is set to [4:3 D. image shift], press the
MENU button, select the [Installation settings] tab with the [ ] and [ ] buttons, and
then select [Digital image shift] with the [ ] and [ ] buttons. (P108)
2
Use [ ] / [ ] to move the image.
Remote control
Projector
Remote control
Screen
[ ] button
Moves the image left
3
[ ] button
Moves the image right
When the image fits the screen, press the OK button.
68
Adjusting the Image
Resetting the Image Shift
■Selecting Aspect Ratio
Select [Aspect] based on the input signal type, aspect ratio of the screen and resolution.
For more details about aspect ratios, refer to page 207.
Types of Aspect Ratios
Full (WUX5000 / WUX4000)
The image is projected using an input signal aspect ratio of 16:10.
Select this to project computer screen images having an aspect ratio of 16:10
(WUXGA, WSXGA+, WXGA+ and WXGA (1280 x 800)) fully on the screen.
This can only be selected when the screen aspect is 16:10.
16:10 (WX6000 / SX6000)
The image is projected using an input signal aspect ratio of 16:10.
Select this if an image of 16:10 aspect ratio cannot be correctly projected in [Auto]
mode when using video software.
16:9
The image is projected using an input signal aspect ratio of 16:9. Select this if an image
of 16:9 aspect ratio cannot be correctly projected in [Auto] mode.
4:3
The image is projected using an input signal aspect ratio of 4:3. Select this if an image
of 4:3 aspect ratio cannot be correctly projected in [Auto] mode.
Zoom
This cuts the upper/lower or left/right part of the image according to the screen aspect
and zooms in or out of the center of the image. Select this if a letter box is displayed
(black lines at the top/bottom of the screen) when using video software.
There may be some cases when this cannot be selected, depending on the input signal and/or
resolution.
True size
The image is projected with the original resolution of the input signal. Select this to
clearly project a computer screen image which has a resolution of WUXGA or lower.
There may be some cases when this cannot be selected, depending on the input signal and/or
resolution.
69
Projecting an Image
Auto
The image is projected at the aspect ratio of the input signal. Select this mode for normal image projection.
User’s Manual
Perform the following steps to reset the image shift adjustment.
Press the D.SHIFT/KEYSTONE button (WUX5000 / WUX4000), twice to display the [D.
image shift reset] window.
Then, select [OK] with the [ ] button and press the OK button.
Adjusting the Image
How to Select an Aspect Ratio
Press the ASPECT button on the remote control and select an appropriate aspect ratio. Press the
ASPECT button to change the aspect ratio type.
For more details about aspect ratios, refer to page 207.
Example:
Remote control
You can also select any aspect ratio from [Aspect] in the menu. (P93)
Some aspect ratios may not appear depending on the type of input signal.
70
Adjusting the Image
Adjusting the Image Size
1
Press either the ZOOM button on the remote control or the LENS button on the projector twice in order to display the window shown below.
Remote control
Projector
Push twice
Remote control
User’s Manual
The size of the projected image can be adjusted by pressing the ZOOM button on the
remote control or the LENS button on the projector. Change the projector installation position if your desired image is too large or too small to adjust it with the zoom function.
(P156)
Projecting an Image
71
Adjusting the Image
2
Press the pointer buttons to adjust the image size.
Remote control
Projector
Remote control
Screen
Use the [ ] button on the remote control, or the UP button on the projector to
increase the image size.
Use the [ ] button on the remote control, or the DOWN button on the projector to
decrease the image size.
3
When the desired image size is selected, press the OK button or the ZOOM button.
When the Short Fixed Lens (RS-IL03WF) is attached, zoom adjustment cannot
be performed.
72
Adjusting the Image
Adjusting the Focus
To adjust the focus, press the FOCUS button on the remote control or the LENS button on
the projector.
For the projection distances of the lens unit, refer to page 156.
Press either the FOCUS button on the remote control or the LENS button on the projector in order to display the window shown below.
Remote control
Projector
Remote control
User’s Manual
1
Projecting an Image
2
Press the pointer buttons to adjust the focus.
Remote control
Projector
Remote control
Use the [ ] button on the remote control, or the UP button on the projector to adjust the
focus position.
Use the [ ] button on the remote control, or the DOWN button on the projector to perform fine adjustment.
3
When the focus is adjusted optimally, press the OK button or the FOCUS button.
73
Adjusting the Image
Adjusting the Image Position
To adjust the screen position up, down, left, or right, press the LENS-SHIFT button
(WUX5000 / WUX4000) or SHIFT button (WX6000 / SX6000) on the remote control, or the
LENS button on the projector. This function is referred to as “lens shift”. It can change the
projected screen to the most suitable position by moving the position of the lens up/down/
left/right. (P160)
• The available range for lens shift (percentage of movement relative to the screen size) varies depending on the lens unit which is used. (P161)
• There are areas where each lens is unable to move. With the Short Fixed Lens (RSIL03WF), the areas are at the four corners and for the other lenses, the areas are at the top
left and bottom right. (P161)
1
Press either the LENS-SHIFT button (WUX5000 / WUX4000) or the SHIFT button
(WX6000 / SX6000) on the remote control, or the LENS button on the projector 3
times in order to display the window shown below.
* If the Short Fixed Focus Lens (RS-IL03WF) is attached, when the LENS button on
the projector is pressed twice, the window below will be displayed.
Remote control
Projector
Push three times*
74
Remote control
Adjusting the Image
2
Press the pointer buttons to adjust.
Remote control
Projector
Remote control
User’s Manual
3
When the desired position is reached, press the OK button.
■Resetting the Position
The lens position after movement with the lens shift function is not returned when the
power is turned off. To return it to its original position, perform reset.
During screen position adjustment, press and hold the LENS-SHIFT button (WUX5000 /
WUX4000) or SHIFT button (WX6000 / SX6000) on the remote control, or the LENS button
on the projector to display the [Lens shift Reset] window.
The selections for the lens currently used are displayed. Use the pointer buttons to select
one of them, then press the OK button.
Lens unit type
Available items
Standard Zoom Lens
RS-IL01ST
Long Zoom Lens
RS-IL02LZ
50% (Home position)
0%
: Up 50%, left / right 0%
: Up / down / left / right 0%
0% (Home position)
: Up / down / left / right 0%
Ultra Long Zoom Lens
RS-IL04UL
Short Fixed Lens
RS-IL03WF
75
Projecting an Image
Screen
Adjusting the Image
Adjusting Keystone Distortion
The D.SHIFT/KEYSTONE button (WUX5000 / WUX4000) or KEYSTONE button
(WX6000 / SX6000) can be used to correct keystone distortion.
• Keystone can be adjusted within the range of ±20 degrees. If the keystone distortion is
too large to adjust, move the projector installation position so that it is completely straight.
• The result of keystone adjustment is stored in memory. If you place the projector in the
same position, the keystone adjustment is not necessary.
• Signals are processed digitally when keystone distortion is corrected. The image may
look different from the original one. In addition, the aspect ratio of the image may change.
• Perform keystone distortion correction with the lens shift position in the home position. Correction will not be performed correctly if the position is not the home position.
1
Press the D.SHIFT/KEYSTONE button (WUX5000 / WUX4000) or KEYSTONE button
(WX6000 / SX6000) to display the window in the center illustration below.
Remote control
Remote control
76
Adjusting the Image
2
Press the pointer buttons to adjust.
Remote control
Projector
Remote control
User’s Manual
[ ] button
[ ] button
Reduces the dimensions of the upper edge Reduces the dimensions of the lower edge
Projecting an Image
Screen
[ ] button
Reduces the dimension of the right edge
[ ] button
Reduces the dimension of the left edge
3
When keystone distortion has been corrected, press the OK button.
■Resetting the Keystone Adjustment
Perform the following steps to reset the keystone adjustment.
Press the D.SHIFT/KEYSTONE button (WUX5000 / WUX4000) or KEYSTONE button
(WX6000 / SX6000) twice to display the [Keystone reset] window.
Then, select [OK] with the [ ] button, and press the OK button.
77
Selecting an Image Mode
You can select an image mode to suit the projected image.
In each image mode, you can further adjust the brightness, contrast, sharpness, gamma,
color adjustment, advanced adjustment, and lamp mode (WUX4000). (P109)
■Image Modes
The image modes which can be selected vary somewhat depending on the selected
input signal.
Compatible input signals
Image
Mode
Digital PC
Analog PC
(WUX5000 / WUX4000)
Analog PC-1, 2
(WX6000 / SX6000)
HDMI (when [HDMI
In] is [Computer])
Component HDMI
(when [HDMI In] is
[Auto])
Explanation
Standard
Suitable for projecting a computer
screen or watching media played with
video software in a brightish room.
This image mode emphasizes white
tones.
Presentation
Suitable for viewing text-based images
in a brightish room.
Dynamic
Suitable for watching media played
with video software in a brightish room.
VividPhoto
Suitable for viewing images with
vibrant colors in a moderately dark
room.
This image mode emphasizes color
saturation.
Photo/
sRGB
Suitable for viewing images taken with
a digital camera that supports sRGB in
a moderately dark room.
This image mode supports the sRGB
standard.
Video
Suitable for watching video taken with
a video camera in a moderately dark
room.
Cinema
Suitable for watching media played
with video software in a dark room.
This image mode enables viewers to
enjoy the atmosphere of a movie theater.
User 1 - 5
* Up to 5 user-selected combinations
of image quality settings can be
stored in the memory. (P110) Stored
settings can be selected as an image
mode.
: Compatible
*
*
: Not compatible
78
Selecting an Image Mode
■How to Select an Image Mode
Press the IMAGE button on the remote control to select.
The image mode changes each time the IMAGE button is pressed. (The displayed image
modes vary depending on the selected input signal.)
User’s Manual
Remote control
79
Projecting an Image
You can also select any image mode from the [Image mode] menu. (P109)
• User settings 1 - 5 are displayed when the desired image settings have been created
and stored using the user memory function in the image adjustment menu. (P110)
Turning Off the Projector
1
Press the POWER button to display the window shown below.
Remote control
Projector
Remote control
When this window is displayed, press the POWER button again to turn off the power.
The lamp goes off, the [STAND BY] indicator starts flashing in red and the cooling
process starts.
• You cannot turn the projector on while the cooling process is in operation.
• If you want to continue projecting without turning off the power, press a button other than
POWER, or else wait until the confirmation message disappears.
• After turning off the projector, wait at least 5 minutes before turning it on again. It may shorten
the lamp life if you turn on the projector immediately after turning it off.
• Using the projector for a long time may shorten the life of the lamp and internal optical
components.
2
Disconnect the power cord from the electrical outlet.
If the power plug is left connected, the [STAND BY] indicator will switch from flashing
to constantly illuminated after the cooling process is completed.
80
Table of Contents
Safety Instructions
Before Use
Projecting an Image
User’s Manual
Useful Functions
Available During
a Presentation
Useful Functions Available
During a Presentation
Setting Functions from Menus
Installation Manual
Installation
Connecting to a Network
Maintenance
Appendix
Appendix
Index
81
Useful Functions Available During a Presentation
Temporarily Blacking Out
an Image
Freezing the Picture
Useful when:
• You want to perform a computer operation
which is irrelevant to the proceedings of the
presentation.
• You want to stop a moving image.
Useful when:
• You have finished the presentation.
• You want to divert attendees’ attention from
the screen.
Remote control
Remote control
Press the FREEZE button to freeze the
moving image. The projector shows the
following icon.
Press the BLANK button to black out the
image.
Press the BLANK button again to show the
image.
• You can set the screen state while blacking out the image in the menu. (P106)
• The lamp remains illuminated while the
image is blacked out.
Screen
Press the FREEZE button again to cancel
the FREEZE function.
• It is also cancelled when the input signal is
terminated.
82
Useful Functions Available During a Presentation
Adjusting the Volume
Muting the Sound
Useful when:
Useful when:
• You want to adjust the volume level of the
projector or external speakers.
• You want to temporality mute unnecessary
sound.
• You want to immediately mute the sound.
Remote control
Press the MUTE button to mute the sound.
The projector shows the following icon.
• You can also adjust the volume level with
the [ ] / [ ] buttons of the projector.
• Adjust the volume or mute setting on the
computer if the volume level is too low.
• You can also adjust the volume level of the
speakers connected via the audio output
terminal.
Screen
For the WX6000 / SX6000, depending
on whether the AUDIO IN terminal has
been set in the Audio in terminal select
screen (P139), there may be no audio
output in some cases.
Press the MUTE button again to cancel the
mute function.
• You can also mute the sound of the speakers connected via the audio output terminal.
83
Useful Functions Available During a Presentation
Press the VOL button. The following
screen appears.
User’s Manual
Remote control
Useful Functions Available During a Presentation
Zooming an Image
Useful when:
• Zooming in on an object such as a small
graph during a presentation (up to 12x).
• Focusing on the current subject.
Press the + D.ZOOM button to enlarge a
part of the image. Press the - D.ZOOM
button to reduce the image size.
You can move the area you want to zoom in
on by using the [ ] / [ ] / [ ] / [ ] buttons.
Remote control
Remote control
Screen
You can restore the original size of the
image by pressing the OK button.
スクリーン
Screen
• The magnification appears on the screen.
84
Useful Functions Available During a Presentation
Showing the Elapsed
Time
Useful when:
• You want to manage the timing of the presentation.
User’s Manual
Useful Functions Available During a Presentation
Screen
Press the P-TIMER button to start counting.
• The elapsed time is displayed on the lower
right corner of the screen.
• Time is counted up to 59:59. The timer
then returns to 00:00.
Remote control
Press the P-TIMER button again to stop
the timer.
• Press the P-TIMER button while the timer
is stopped. The timer disappears from the
screen. Then press the P-TIMER button to
start counting from 00:00.
85
86
Table of Contents
Safety Instructions
Setting Functions from Menus
Before Use
Projecting an Image
User’s Manual
Useful Functions Available
During a Presentation
Setting Functions from Menus
Installation
Installation Manual
Connecting to a Network
Maintenance
Appendix
Appendix
Index
87
How to Use Menus
Use the menus to set the operation of the projector in detail.
■Menu Configuration
The menu screen is divided into 5 tabs as shown below.
[Display settings] tab
You can set the type of signal
or the method of projection of
the images input.
[System settings] tab
You can set the operation of the projector.
[Network setting] tab
These settings are for when using the
projector from a PC via a network.
For the network settings, refer to page
165.
[Image adjustment] tab
You can adjust the image quality
and colors according to your
preference.
[Information] tab
You can check information about the
signal types of the images projected
and other projector-specific information.
Menu items
Contents of menu
Input Signal Types for which a Menu Item is Displayed
Different menu items are displayed for different input signal types.
In the following explanation of each menu item, the input signal type for which the
menu item is displayed is indicated as follows:
Input signal for which the
menu item is displayed
Input signal for which the
menu item is not displayed
HDMI
Component
Digital PC
Analog PC
88
How to Use Menus
The menu screen is divided into 6 tabs as shown below.
[Install settings] tab
This setting is used when installing the projector.
[Input settings] tab
You can set the type of signal or
the method of projection of the
images input.
[System settings] tab
You can set the operation of the projector.
[Image adjustment] tab
You can adjust the image quality and colors according to your
preference.
Menu items
Contents of menu
89
Setting Functions from Menus
[Information] tab
You can check information about the
signal types of the images projected
and other projector-specific information.
User’s Manual
[Network setting] tab
These settings are for when using the
projector from a PC via a network.
For the network settings, refer to page
165.
How to Use Menus
■Basic Menu Operations
The menus shown below are for WUX5000.
1
Press the [MENU] button to display the menu window.
Remote control
2
Projector
Remote control
Use the [ ] / [ ] buttons to select a tab.
Remote control
Projector
Remote control
• If the tab position is not highlighted in orange, use the [ ] / [ ] buttons to move the
highlight to the top.
90
How to Use Menus
3
Use the [ ] / [ ] buttons to select an item.
Remote control
Projector
Remote control
User’s Manual
Setting Functions from Menus
91
How to Use Menus
4
Select contents.
How to select the contents varies depending on the item.
Selecting from a list Example: Aspect
1. Select Aspect.
2. Press the OK button or [ ] button to display a list of the contents.
3. Use the [ ] / [ ] buttons to select the
desired contents.
4. When you have found the contents you
desired, press the OK button or [ ].
Adjusting with the [ ] / [ ] buttons Example: Contrast
1. Select Contrast.
2. Use the [ ] / [ ] buttons to adjust the setting.
Selecting from a different screen (1) Example: Menu position
1. Select Menu position.
2. Press the OK button to display a different
screen.
3. Then follow the instruction on the screen.
Selecting from a different screen (2) Example: Tracking
1. Select Input signal settings.
2. Select Tracking.
3. Press the OK button to display a different
screen.
4. Use the [ ] / [ ] buttons to select the setting, then use the [ ] / [ ] buttons to select
the value.
5. When you have completed the settings,
press the OK button.
5
Pressing the MENU button causes the menu screen to disappear.
The menu screen will also disappear if the EXIT button (WX6000 / SX6000) is
pressed.
92
Setting Display Status
Selecting an Image Projection Mode
Auto
An image is projected at the
aspect ratio of the input signal.
Select this mode for normal image
projection.
Full (WUX5000 / WUX4000)
The image is projected using an
input signal aspect ratio of 16:10.
Select this to project computer
screen images with an aspect ratio
of 16:10 (WUXGA, WSXGA+,
WXGA+ and WXGA (1280 x 800))
fully on the screen.
[Aspect]
HDMI
Component
Digital PC
Analog PC
You can select a projection mode corresponding to the aspect ratio of the image.
(P69)
This can only be selected when
the screen aspect is 16:10.
MENU > [Display settings] > [Aspect]
There may be some cases when
this cannot be selected, depending on the input signal and/or resolution.
True size
The image is projected with the original resolution of the input signal.
Select this to clearly project a computer
screen image that has a resolution of
WUXGA and lower (WUX5000 /
WUX4000), WXGA+ and lower
(WX6000) or SXGA+ and lower
(SX6000).
• Different contents are displayed for different screen aspects or input signal types.
• The ASPECT button on the remote control
can also be used to select the Aspect settings.
There may be some cases when
this cannot be selected, depending on the input signal and/or resolution.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
93
Setting Functions from Menus
MENU > [Input settings] > [Aspect]
User’s Manual
16:10 (WX6000 / SX6000)
The image is projected using an
input signal aspect ratio of 16:10.
16:9
The image is projected using an
input signal aspect ratio of 16:9.
Select this if an image of 16:9
aspect ratio cannot be correctly
projected in [Auto] mode.
4:3
The image is projected using an
input signal aspect ratio of 4:3.
Select this if an image of 4:3
aspect ratio cannot be correctly
projected in [Auto] mode.
Zoom
This cuts the upper/lower or left/
right part of the screen according
to the screen aspect and zooms in
or out of the center of the image.
Select this if a letter box is displayed (black lines at the top/bottom of the screen) when using
video software.
Setting Display Status
Automatic Display
Adjustment
Selecting an Input Signal
Type (Analog PC)
[Auto PC]
[Input signal select]
HDMI
Digital PC
Component
Analog PC
HDMI
Component
Digital PC
Analog PC
Automatically adjusts display position misalignment and screen flickering. The
adjusted result is stored in the memory.
You can select a suitable resolution if the
auto PC adjustment function (P62) cannot
project the correct image from a computer.
MENU > [Input settings] > [Auto PC]
MENU > [Display settings] > [Input signal select]
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
MENU > [Input settings] > [Input signal select]
If [Auto PC] adjustment is insufficient,
perform the following operations.
• Select the input signal that matches
the resolution of the computer from
[Input signal select]. (P94)
• If adjustment is insufficient even
when using the above operation,
adjust [Total dots], [Tracking], [Horizontal/Vertical position] and [Horizontal/Vertical pixels] in [Input signal
settings]. (P95 – P98)
• For details about signal formats that
are compatible with the projector,
refer to page 218.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
Select an input signal corresponding to
the resolution of the computer.
• For the signal types supported by the projector, see the table on page 218.
94
Setting Display Status
Selecting an Input Signal
Type (Component)
Adjust Input Signal Type
(Analog PC) Total Dots
[Input signal select]
[Total dots]
HDMI
Component
HDMI
Component
Digital PC
Analog PC
Digital PC
Analog PC
You can select the proper component signal type if the video image from AV equipment is not projected correctly.
You can adjust the total number of dots in
the horizontal direction.
Adjust it when stripes are displayed on the
screen.
MENU > [Display settings]> [Input signal select]
MENU > [Input settings] > [Input signal
settings] > [Total dots]
Use [ ] / [ ] to select a value.
When you have completed the adjustment, press the OK button to accept your
setting and then press the MENU button
or EXIT button (WX6000 / SX6000).
• [Auto] is the factory default.
• Refer to the user’s manual for the AV
equipment connected to the projector to
confirm the component signal type.
• Perform this adjustment if the [AUTO PC]
function (P62) cannot adjust the projected
image correctly.
95
Setting Functions from Menus
Press the OK button to accept your setting
and then press the MENU button.
User’s Manual
MENU > [Display settings]> [Input signal settings] > [Total dots]
Setting Display Status
Adjust Input Signal Type
(Analog PC) Tracking
Adjust Input Signal Type
(Analog PC) Horizontal
Position
[Tracking]
HDMI
Component
Digital PC
Analog PC
[Horizontal position]
You can fine-tune the timing for generating
an image from the image signal.
Adjusts the tracking when the image distorts or flickers.
HDMI
Component
Digital PC
Analog PC
You can adjust the horizontal position of
the screen when the projected image is
shifted in the horizontal direction.
MENU > [Display settings]> [Input signal settings] > [Tracking]
MENU > [Display settings]> [Input signal settings] > [Horizontal position]
MENU > [Input settings] > [Input signal
settings] > [Tracking]
MENU > [Input settings] > [Input signal settings]
> [Horizontal position]
Use [ ] / [ ] to select a value.
When you have completed the adjustment, press the OK button to accept your
setting and then press the MENU button
or EXIT button (WX6000 / SX6000).
Use [ ] / [ ] to select a value. As the
value increases, the screen moves to the
left.
• Perform this adjustment if the [AUTO PC]
function (P62) cannot adjust the projected
image correctly.
Screen
When you have completed the adjustment, press the OK button to accept your
setting and then press the MENU button
or EXIT button (WX6000 / SX6000).
• Perform this adjustment if the [AUTO PC]
function (P62) cannot adjust the projected
image correctly.
96
Setting Display Status
Adjust Input Signal Type
(Analog PC) Vertical Position
Adjust Input Signal Type
(Analog PC) Horizontal
Pixels
[Vertical position]
[Horizontal pixels]
HDMI
Component
HDMI
Component
Digital PC
Analog PC
Digital PC
Analog PC
You can adjust the vertical position of the
screen when the projected image is shifted
in the vertical direction.
You can adjust the number of the pixels in
the horizontal direction if the length of the
screen is too long or too short in the horizontal direction.
MENU > [Display settings]> [Input signal settings] > [Horizontal pixels]
MENU > [Input settings] > [Input signal
settings] > [Vertical position]
MENU > [Input settings] > [Input signal
settings] > [Horizontal pixels]
Use [ ] / [ ] to select a value.
Screen
Screen
When you have completed the adjustment, press the OK button to accept your
setting and then press the MENU button
or EXIT button (WX6000 / SX6000).
When you have completed the adjustment, press the OK button to accept your
setting and then press the MENU button
or EXIT button (WX6000 / SX6000).
• Perform this adjustment if the [AUTO PC]
function (P62) cannot adjust the projected
image correctly.
• Perform this adjustment if the [AUTO PC]
function (P62) cannot adjust the projected
image correctly.
97
Setting Functions from Menus
Use [ ] / [ ] to select a value. As the
value increases, the screen moves
upward.
User’s Manual
MENU > [Display settings]> [Input signal settings] > [Vertical position]
Setting Display Status
Adjust Input Signal Type
(Analog PC) Vertical Pixels
Selecting HDMI Input
Level
[Vertical pixels]
[HDMI input level]
HDMI
Component
HDMI
Component
Digital PC
Analog PC
Digital PC
Analog PC
You can adjust the number of the pixels in
the vertical direction if the screen is too
long or too short in the vertical direction.
You can select this as required when you
project visual software with an HDMI signal.
MENU > [Display settings] > [Input signal settings] > [Vertical pixels]
MENU > [Display settings] > [HDMI input level]
MENU > [Input settings] > [Input signal
settings] > [Vertical pixels]
Use [ ] / [ ] to select a value.
MENU > [Input settings] > [HDMI input level]
Screen
When you have completed the adjustment, press the OK button to accept your
setting and then press the MENU button
or EXIT button (WX6000 / SX6000).
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• [Auto] is the factory default.
• You can select this only when the type of signal sent from AV equipment is RGB.
• The signal level is selected automatically in
[Auto] mode. (Some AV equipment may not
support this.)
• If the HDMI output of your AV equipment
allows switching between [Normal] and
• Perform this adjustment if the [AUTO PC]
function (P62) cannot adjust the projected
image correctly.
98
Setting Display Status
HDMI Color Format
[Expanded], we recommend you to set
[Expanded]. The contrast of images will be
improved and dark scenes will be rendered
more realistically. In this case, select [Auto]
or [Expanded] for the HDMI input level.
For more detailed information, refer to the
user’s manual for the AV equipment connected to the projector.
[HDMI color space]
HDMI
Component
Digital PC
Analog PC
Select the color space for the HDMI signal.
MENU > [Display settings] > [HDMI color space]
User’s Manual
MENU > [Input settings] > [HDMI color space]
Selects the optimal color format
for the input HDMI signal.
RGB
Forces the projector to handle the
input signal as an RGB signal.
YCbCr
Forces the projector to handle the
input signal as a color difference
signal.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• [Auto] is the factory default.
99
Setting Functions from Menus
Auto
Setting Display Status
Select HDMI Over Scan
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
[HDMI over scan]
HDMI
Component
Digital PC
Analog PC
• The factory defaults settings are [On]
when [HDMI In] (P127) is set for [Auto]
and [Off] when it is set for [Computer].
You can select this as required when you
project visual software using an HDMI signal.
MENU > [Display settings] > [HDMI over scan]
MENU > [Input settings] > [HDMI over scan]
Off
The entire input signal (100%) is projected. The images projected may be
smaller than the full projection screen.
On
Images are projected with distortion
at the peripheral section of images
trimmed off. (The central 95% of the
images are projected.)
Part of the peripheral sections of
images may be cut out depending on
the resolution of the signal. In such a
case, select [Off].
100
Setting Display Status
Performing Progressive
Processing
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
[Progressive]
HDMI
Component
Digital PC
Analog PC
You can select this as required when the
images have low resolution.
MENU > [Display settings] > [Progressive]
• [Auto] is the factory default.
• When [HDMI In] (P127) is [Computer], this
can only be set when the input signal is
1080i, 1035i, 576i or 480i and the input
signal color space is YCbCr422.
• Select [Off] when flickers and horizontal
lines are noticeable in media that has a lot
of fast-moving action.
User’s Manual
Setting Functions from Menus
MENU > [Input settings] > [Progressive]
Off
Does not perform progressive
processing.
On
Performs progressive processing.
This mode is available when the
HDMI signal is 1080i, or component signal is 1080i, 1035i, 576i
or 480i.
Auto
Performs the appropriate progressive processing according to
the input signal.
101
Setting Display Status
Selecting a Menu Position
When the menu has been moved to the
desired position, press the OK, MENU or
EXIT button (WX6000 / SX6000).
[Menu position]
HDMI
Component
Digital PC
Analog PC
You can change the position of menus displayed.
MENU > [Display settings] > [Menu position]
MENU > [Install settings] > [On screen] > [Menu
position]
Move the menu to the desired position
with the [ ] / [ ] / [ ] / [ ] buttons.
102
Setting Display Status
Correcting the Screen
Color
Adjust
[Screen color]
HDMI
Component
Digital PC
Analog PC
Use the [ ] / [ ] buttons to select a
primary color.
[ ] makes the color selected darker.
[ ] makes the color selected lighter.
You can adjust the color quality of the
images projected according to the color of
the projection screen.
MENU > [Display settings] > [Screen color]
Select this to make detailed adjustment.
The following popup screen will
appear.
• [Normal] is the factory default.
Setting Functions from Menus
MENU > [Install settings] > [Screen color]
Normal
Greenboard
User’s Manual
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
Select this if a standard type of projection screen is used. The images
are projected in a light quality similar
to that of natural light.
Select this if a greenboard (dark
green color) is used for the projection screen. The color quality similar
to [Normal] is obtained on the
greenboard.
103
Setting Display Status
Reversing Projection
Rear, CeilSelect this to project an image
ing mounted from behind the screen with the
projector hung from the ceiling.
The projected image is inverted
in the vertical direction.
[Image flip H/V]
HDMI
Component
Digital PC
Analog PC
Select this setting if you want to hang the
projector from the ceiling or project an
image from behind the screen.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
MENU > [Display settings] > [Image flip H/V]
• [None] is the factory default.
MENU > [Install settings] > [Image flip H/V]
None
Select this to project an image
normally.
Ceiling
mounted
Select this to project an image
with the projector hung from the
ceiling.
The projected image is inverted
in both vertical and horizontal
directions.
Rear
Select this to project an image
from behind the screen.
The projected image is inverted
in the horizontal direction.
104
Setting Display Status
Normal projection (none)
No Signal Screen
[No signal screen]
HDMI
Component
Digital PC
Analog PC
You can display either a black or blue
screen when there is no input signal.
Ceiling mounted projection
MENU > [Display settings]> [User screen settings] > [No signal screen]
Rear projection
The screen is all black.
Blue
The screen is all blue.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• [Blue] is the factory default.
Rear ceiling mounted projection
• To hang the projector from the ceiling, use
the optional bracket. Contact the Canon
Customer Support Center for more
detailed information.
• If you flip the image, the keystone distortion adjustment will be reset.
105
Setting Functions from Menus
Black
User’s Manual
MENU > [System settings] > [User screen settings] > [No signal screen]
Setting Display Status
Screen When Blank
Selecting a Logo at Startup
[Screen when blank]
HDMI
Component
Digital PC
Analog PC
[Projector on]
You can display a black or blue screen and
temporarily blank out the projected image
by pressing the BLANK button on the
remote control.
Blue
The screen is all blue.
Analog PC
MENU > [Display settings] > [User screen settings] > [Projector on]
MENU > [System settings] > [User screen settings] > [Screen when blank]
The screen is all black.
Component
Digital PC
You can display a specified logo on the
screen from the moment the projector is
turned on to the moment it is ready for projection.
MENU > [Display settings] > [User screen settings] > [Screen when blank]
Black
HDMI
MENU > [System settings] > [User screen settings] > [Projector on]
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
Skip
Projects an input signal
immediately after turning on
the projector.
Canon logo
Displays the Canon logo that
was registered in advance at
the factory.
• [Black] is the factory default.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• [Canon logo] is the factory default.
106
Setting Display Status
Selecting Aspect Ratio of
Screen
16:9
D.
image
shift
[Screen aspect]
HDMI
Component
Digital PC
Analog PC
4:3
D.
image
shift
(Except
for
SX6000)
Select according to the aspect ratio of the
projection screen. (P63)
MENU > [Display settings]> [Screen aspect]
Select this when you use a screen
with an aspect ratio of 16:9.
Keystone correction cannot be
performed in this mode. However,
it is possible to move the image
up / down when projecting level.
For details about how to move the
image, refer to page 67.
Select this when you use a screen
with an aspect ratio of 4:3.
Keystone correction cannot be
performed in this mode. However,
it is possible to move the image
left / right when projecting level.
For details about how to move the
image, refer to page 68.
16:10
16:9
4:3
16:10 D
image
shift
(SX6000)
Select this when you use a screen
with an aspect ratio of 16:10.
Select this when you use a screen
with an aspect ratio of 16:9.
Select this when you use a screen
with an aspect ratio of 4:3.
Select this when the screen
aspect ratio is 16:10. Keystone
correction cannot be performed in
this mode. However when projecting level, it is possible to shift the
image up or down. For details
about how to shift the image, refer
to page 67.
107
Setting Functions from Menus
MENU > [Install settings] > [Screen aspect]
• The factory default is [16:10] for the
WUX5000 / WUX4000 / WX6000, and [4:3]
for the SX6000.
• If you select [16:9 D. image shift], [4:3 D.
image shift], or [16:10 D. image shift] (for
SX6000), the keystone correction will be
canceled. For more details, refer to page
66.
• [Auto] may be automatically selected for
the aspect depending on the screen
aspect setting.
User’s Manual
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
Setting Display Status
Adjusting Keystone Distortion
Image Shift Adjustment
[Digital image shift]
HDMI
Digital PC
[Keystone adjustment]
HDMI
Digital PC
Component
Analog PC
Component
Analog PC
Moves the position of the projected image.
Corrects keystone distortion.
MENU > [Install settings] > [Digital image shift]
MENU > [Install settings] > [Keystone adjustment]
If the OK button or [ ] button is pressed,
the D image shift adjustment screen is displayed.
If the OK button or [ ] button is pressed,
the Keystone adjustment screen is displayed.
Correct using the [ ] / [ ] buttons. When
you have finished correcting, press the OK
button.
Correct using the [ ] / [ ] / [ ] / [ ] buttons. When you have finished correcting,
press the OK button.
• This cannot be selected when the screen
aspect is 16:9, 16:10 or 4:3.
• When the screen aspect is 16:9D image shift
or 16:10D image shift (SX6000), the image
can be adjusted vertically, and when the
screen aspect is 4:3D image shift (WX6000),
it can be adjusted horizontally.
• This cannot be selected when the screen
aspect is 16:9D image shift, 16:10D image
shift or 4:3D image shift.
• The Keystone adjustment screen can also be
displayed by pressing the KEYSTONE button on the remote control. (P76)
108
Selecting an Image Quality
Image Adjustment
[Image mode]
HDMI
Component
Digital PC
Analog PC
You can select an image mode suitable for
the projected image. (P78)
You can also select it with the IMAGE button on the remote control. (P79)
MENU > [Image adjustment] > [Image mode]
MENU > [Image adjustment] > [Image mode]
Standard
Presentation
Dynamic
Suitable for projecting a computer
screen or watching media played
with video software in a brightish
room.
This image mode emphasizes
white tones.
Suitable for viewing text-based
images in a brightish room.
Suitable for watching media
played with video software in a
brightish room.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• [Standard] is the factory default.
• You can adjust the image quality by
adjusting the following items in each
image mode:
[Brightness], [Contrast], [Sharpness],
[Gamma], [Color adjustment],
[Advanced adjustment] and [Lamp
mode] (WUX4000)
• The adjustment you have made is
stored as each combination of input signals and an image mode.
• When a user memory that was saved in
[Create profile] is selected, [Baseline
Image Mode] appears in the menu. This
indicates the image mode that was the
base when the user memory was saved.
109
Setting Functions from Menus
(The screen is for the WUX5000.)
User’s Manual
VividPhoto Suitable for viewing images with
vibrant colors in a moderately
dark room.
This image mode emphasizes
color saturation.
Photo/
Suitable for projecting images
sRGB
taken with a digital camera that
supports sRGB in a moderately
dark room. Supports the sRGB
standard.
Video
Suitable for watching video taken
with a video camera in a moderately dark room.
Cinema
Suitable for watching media
played with video software in a
dark room.
This image mode enables viewers
to enjoy the atmosphere of a
movie theater.
User 1 - 5 Up to 5 user-selected combinations of image quality settings can
be stored in the memory. (P110)
Stored settings can be selected
as an image mode.
Selecting an Image Quality
Saving the Desired Image
Quality
[Create profile]
HDMI
Component
Digital PC
Analog PC
Up to 5 combinations of image quality settings can be stored. The stored image
quality can be selected as an image mode.
(The screen is for the WUX5000.)
MENU > [Image adjustment] > [Create Profile]
(The screen is for the WUX5000.)
MENU > [Image adjustment] > [Create profile]
Use the [ ] / [ ] buttons and select the
save destination. (Saved memories are
indicated by checkmarks.)
110
Selecting an Image Quality
When the desired save destination is
selected, press the OK button to accept
your setting and then press the [Return]
button.
[Brightness]
HDMI
Component
Digital PC
Analog PC
You can adjust the brightness of images.
MENU > [Image adjustment] > [Brightness]
(The screen is for the WUX5000.)
[ ]
Increases the brightness of an image.
[ ]
Decreases the brightness of an image.
When you have completed the adjustment, press the OK button to accept your
setting and then press the MENU button
or EXIT button (WX6000 / SX6000).
• The adjustment you have made is stored
as adjusted values for the input signals
and image mode of the current projection.
111
Setting Functions from Menus
MENU > [Image adjustment] > [Brightness]
User’s Manual
• The saved settings consist of the brightness,
contract, sharpness, gamma, color adjustment, advanced adjustment, and lamp mode
(WUX4000).
• The number of displayed user memories is 5,
however it is possible to save different settings for when the connected equipment is a
computer (ANALOG PC, DIGITAL PC or
HDMI (when [HDMI In] (P127) is [Computer])
and when AV equipment is connected (COMPONENT, HDMI (when [HDMI In] (P127) is
[Auto])). As a result, it is possible to save up
to 10 settings.
• The image mode name which was the basis
for the settings change is also saved in the
user memory. When a user memory is
selected as the image mode, the image
mode that was the base for that user memory
is displayed in the menu as [Baseline image
mode].
Adjusting the Brightness
Selecting an Image Quality
Adjusting the Contrast
When you have completed the adjustment, press the OK button to accept your
setting and then press the MENU button
or EXIT button (WX6000 / SX6000).
[Contrast]
HDMI
Component
Digital PC
Analog PC
• The adjustment you have made is stored
as adjusted values for the input signals
and image mode of the current projection.
You can adjust the contrast of images.
Adjust the difference between the light and
dark parts of the image to produce an
image with emphasized contrast or an
image that is soft.
MENU > [Image adjustment] > [Contrast]
(The screen is for the WUX5000.)
MENU > [Image adjustment] > [Contrast]
[ ]
Increases the contrast of an image.
This emphasizes the darker and
brighter parts of the image on the projected image.
[ ]
Decreases the contrast of an image.
The image becomes less vivid.
112
Selecting an Image Quality
Adjusting the Sharpness
[Sharpness]
HDMI
Component
Digital PC
Analog PC
Performing Gamma Correction
[Gamma]
You can adjust the sharpness of images.
MENU > [Image adjustment] > [Sharpness]
HDMI
Component
Digital PC
Analog PC
You can correct portions of an image that
are difficult to see because they are too
dark or bright.
For the WUX5000 / WUX4000, correction
can be made by using the GAMMA button
on the remote control.
(The screen is for the WUX5000.)
(The screen is for the WUX5000.)
MENU > [Image adjustment] > [Gamma]
[ ]
Increases the sharpness of an image.
[ ]
Decreases the sharpness of an image.
When you have completed the adjustment, press the OK button to accept your
setting and then press the MENU button
or EXIT button (WX6000 / SX6000).
• The adjustment you have made is stored
as adjusted values for the input signals
and image mode of the current projection.
[ ]
Brightens the dark portion
[ ]
Darkens the bright portion
When you have completed the adjustment, press the OK button to accept your
113
Setting Functions from Menus
MENU > [Image adjustment] > [Sharpness]
User’s Manual
MENU > [Image adjustment] > [Gamma]
Selecting an Image Quality
Adjusting Color
setting and then press the MENU button
or EXIT button (WX6000 / SX6000).
[Color adjustment]
• The adjustment you have made is stored
as adjusted values for the input signals
and image mode of the current projection.
• More detailed adjustment is possible by
using the detailed gamma correction
(P118).
HDMI
Component
Digital PC
Analog PC
You can adjust the color depth and hue of
images for each primary color, red, green
and blue. The color temperature can also
be adjusted.
MENU > [Image adjustment] > [Color adjustment]
Color
level
Color
balance
Color
temperature
R/G/B
Gain
R/G/B
Offset
Adjusts the intensity of each color.
[ ] Increases the intensity of color.
[ ] Decreases the intensity of color.
Adjusts the color balance of a purplish
or greenish image.
[ ] Corrects a purplish image.
[ ] Corrects a greenish image.
Adjusts the color temperature of the
image.
[ ] Changes to a bluish color (cold color).
[ ] Changes to a reddish color (warm color).
Adjust the intensity of each color.
[ ] Increases the color intensity.
[ ] Decreases the color intensity.
Adjusts the color reproducibility of
dark portions of each color.
[ ] Increases the color reproducibility.
[ ] Decreases the color reproducibility.
When you have completed the adjustment, press the OK button to accept your
setting and then press the MENU button
or EXIT button (WX6000 / SX6000).
• The adjustments you have made are
stored as adjusted values for the input signals and image mode of the current projection.
114
Selecting an Image Quality
Correcting the Image
According to the Ambient Light
Level
[Ambient light]
HDMI
Component
Digital PC
Analog PC
You can correct and more effectively
project an image according to the ambient
light on the screen.
L Select this if the ambient light
is low.
M Select this if the ambient light
is normal.
H Select this if the ambient light
is high (bright).
Examples of Ambient Light Level Settings
MENU > [Image adjustment] > [Advanced
adjustment] > [Ambient light]
Level Example Location
Projection room, sports bar, etc.
M
Photo studio, gallery
H
Conference room, lecture room
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
Projects an image with no correction.
Adjust
You can specify the type and
level (brightness) of the ambient
light.
Type
Tungsten
Select this if the
ambient light
source is a light
bulb or bulb color
fluorescent.
Fluorescent Select this if the
ambient light
source is a day
white fluorescent.
Fluorescent H Select this if the
ambient light
source is a daylight color fluorescent.
• [Off] is the factory default.
• [Ambient light] can be set only in the following image modes.
- HDMI (when [HDMI In] is [Auto]) or
COMPONENT:
Video, Cinema, Photo/sRGB
- HDMI (when [HDMI In] is [Computer]),
DIGITAL PC or ANALOG PC:
Photo/sRGB
115
Setting Functions from Menus
Off
User’s Manual
L
Selecting an Image Quality
Noise Reduction
Dynamic Gamma
[Noise reduction]
[Dynamic gamma]
HDMI
Component
HDMI
Component
Digital PC
Analog PC
Digital PC
Analog PC
You can reduce image noise.
You can adjust the gradation representation of light and dark portions of an image
automatically.
MENU > [Image adjustment] > [Advanced
adjustment] > [Noise reduction]
MENU > [Image adjustment] > [Advanced
adjustment] > [Dynamic gamma]
Off
Disables noise reduction.
Weak
Middle
Strong
Specifies the intensity of the noise
reduction in three steps.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• The factory default for HDMI (when [HDMI
In] (P127) is set to [Auto]) is [Off] and
when Component is used, it is set to
[Weak].
• Noise reduction may produce motion artifacts when projecting fast-moving images.
• Select [Weak] for fast-moving images.
Select [Strong] for slow-moving images.
• The adjustment you have made is stored
as adjusted values for the input signals
and image mode of the current projection.
• When [HDMI In] (P127) is [Computer], this
setting is not displayed.
116
Off
Dynamic gamma is disabled.
Weak
Middle
Strong
Specifies the intensity of the
dynamic gamma in three steps.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• The factory default settings are [Off] when
the connected equipment is a Computer
(ANALOG PC, DIGITAL PC, HDMI (when
[HDMI In] (P127) is [Computer])) and
[Weak] when the connected equipment is
AV equipment (COMPONENT, HDMI
(when [HDMI In] (P127) is [Auto])).
• The adjustment you have made is stored
as adjusted values for the input signals
and image mode of the current projection.
Selecting an Image Quality
Memory Color Correction
[Mem. color correct]
HDMI
Component
Digital PC
Analog PC
This function produces beautiful skin
tones, blues, and other colors.
MENU > [Image adjustment] > [Advanced
adjustment] > [Mem. color correct]
6-axis Color Adjust
(Detailed Color Adjustment)
[6-axis color adjust]
HDMI
Component
Digital PC
Analog PC
You can make fine adjustments to the
image colors with RGB (red, green, blue)
and CMY (cyan, magenta, yellow).
MENU > [Image adjustment] > [Advanced
adjustment] > [6-axis color adjust]
Disables the memory color correction function.
Off
Disables 6-axis color adjustment.
If you select [Adjust], the previous
setting of 6-axis color adjustment
becomes active again.
Adjust
Enables 6-axis color adjustment.
Specifies the intensity of the memory
color correction in three steps.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• The factory default settings are as follows.
- For HDMI (when [HDMI In] (P127) is set
to [Computer]), Digital PC and Analog
PC, when any image mode is used
except [VividPhoto], the default setting
is [Off]. When [VividPhoto] is used, the
default setting is [M].
- For HDMI (when [HDMI In] (P127) is set
to [Auto]) and Component, the default
setting is [L], regardless of the image
mode.
• The adjustment you have made is stored
as adjusted values for the input signals
and image mode of the current projection.
Use the [ ] / [ ] buttons to select
[ Hue], [ Saturation], or [* Brightness], then adjust them with the [ ] /
[ ] buttons.
When color adjustments are completed, press the OK button.
Reset
Returns all adjustment values to zero.
When you have completed the adjustment, press the OK button to accept your
setting and then press the MENU button
or EXIT button (WX6000 / SX6000).
• [Off] is the factory default.
• The adjustments you have made are stored
as adjusted values for the input signals and
image mode of the current projection.
117
Setting Functions from Menus
L
M
H
User’s Manual
Off
Selecting an Image Quality
Detailed Gamma Correction
[Fine-Tune Gamma]
HDMI
Component
Digital PC
Analog PC
The four gamma curves (white, red, green,
blue) can be adjusted. When the white
curve is adjusted, the adjustment is also
applied to the other three colors. This function allows more fine-tuned gamma correction. When either of these two functions is
adjusted, the settings of the other are overwritten.
MENU > [Image adjustment] > [Advanced
adjustment] > [Fine-Tune Gamma]
Select [Fine-Tune Gamma] then press the
OK button. The following [Fine-Tune
Gamma] screen for confirmation appears.
118
Use the [ ] / [ ] buttons to select the
color, then press the OK button. Next use
the [ ] / [ ] buttons to select a point on
the gamma curve, and use the [ ] / [ ]
buttons to adjust the position of the point.
When you have completed the adjustment, press the OK button to accept your
setting and then press the MENU button
or EXIT button (WX6000 / SX6000).
• The adjustments you have made are
stored as adjusted values for the input signals and image mode of the current projection.
• For details of gamma correction, refer to
page 113.
Selecting an Image Quality
Reducing the Lamp
Brightness
Resetting the Image
Adjustment Settings
[Lamp mode]
[Reset]
HDMI
Component
HDMI
Component
Digital PC
Analog PC
Digital PC
Analog PC
You can reset the current image adjustment settings to the default settings. If
reset is performed when user setting 1 - 5
is selected for [Image mode], the settings
are returned to the settings that were
saved in [User setting 1 - 5].
MENU > [Image adjustment] > [Lamp mode]
MENU > [Image adjustment] > [Reset]
Projects an image at the normal
brightness level.
Quiet
Reduces the lamp brightness and
cooling fan noise.
Press the OK button to accept your setting
and then press the MENU button.
Resets the image adjustment settings.
Cancel
Cancels resetting of the image
adjustment settings.
• Only the setting for the combination of
input signal and image mode for the current projection is reset.
• [Normal] is the factory default.
• The adjustment you have made is stored
as adjusted values for the input signals
and image mode of the current projection.
119
Setting Functions from Menus
Normal
OK
User’s Manual
Reducing the lamp brightness reduces
power consumption and cooling fan noise.
For the WUX4000, you can also enable or
disable this mode with the LAMP button on
the remote control.
Setting Various Functions
Selecting the Power Management Mode
Exit
[Power management mode]
HDMI
Component
Digital PC
Analog PC
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
You can turn off the lamp or projector automatically in order to save power when the
projector is not in use.
MENU > [System settings] > [Power management mode]
MENU > [System settings] > [Power management mode]
Off
If no input signal is received for 30
seconds, it displays the countdown
and turns off the projector after 5
minutes.
Disables the power management
mode.
Standby If no input signal is received for 30
seconds, the countdown will be displayed and after 5 minutes, the
lamp will turn off.
If it receives an input signal or is
operated during this period, it
resumes projection.
120
• [Off] is the factory default.
• During standby mode, the [POWER ON]
indicator and [STAND BY] indicator flash
alternately.
• You cannot enable the [Direct power on]
function (see the next item), if you select
[Off].
Setting Various Functions
Skip the POWER Button
Operation
• Before setting the direct power on to
[On], be sure to set the [Power management mode] to [Standby] or
[Exit].
• After turning off the projector, wait at
least 5 minutes before turning it on
again. It may shorten the lamp life if
you turn on the projector immediately
after turning it off.
[Direct power on]
HDMI
Component
Digital PC
Analog PC
You can turn on the projector by connecting the power cable without pressing the
POWER button.
MENU > [System settings] > [Direct power on]
User’s Manual
Setting Functions from Menus
MENU > [System settings] > [Direct power on]
Off
You need to press the POWER button
to turn on the projector.
On
You can turn on the projector by connecting the power cable only.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• [Off] is the factory default.
121
Setting Various Functions
Enabling / Disabling the
Beep
Key Repeat
[Key repeat]
HDMI
Digital PC
[Beep]
HDMI
Component
Digital PC
Analog PC
Component
Analog PC
By pressing and holding the button on the
projector or the remote control you can
operate Key repeat in the same was as
when the button is pressed repeatedly.
You can select whether a beep sounds or
not when you operate the projector.
MENU > [System settings] > [Beep]
MENU > [System settings] > [Key repeat]
MENU > [System settings] > [Beep]
Off
Key repeat is not enabled.
On
Key repeat is enabled.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• The factory default is [On].
• Even when Key repeat is [Off], Focus adjustment, Zoom Adjustment and Lens shift
adjustment can still be used.
Off
Disables the beep.
On
Enables the beep.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• [On] is the factory default.
• The beep will not sound if you mute the
projector sound with the MUTE button on
the remote control.
122
Setting Various Functions
Prohibiting Operations
The key lock function becomes effective from the moment the OK button is
pressed after selecting [Main unit] or
[Remote control]. Control via the item
selected will then be disabled.
[Key lock]
HDMI
Component
Digital PC
Analog PC
To Unlock Key Lock Function
Turn off the projector and unplug the
power plug. Hold down the OK button
on the main unit and connect the
power plug. Keep holding down the
OK button until a beep sounds. The
key lock will be unlocked.
You can lock the projector to prevent its
operation from either the main unit or
remote control.
MENU > [System settings] > [Key lock]
User’s Manual
Setting Functions from Menus
MENU > [System settings] > [Key lock]
Off
Main
unit
Disables the key lock.
Operation is not possible using the
main unit.
Use the remote control.
Remote Infrared remote control operations
control can no longer be performed. Use the
main unit button. If using the
WX6000 / SX6000, this can also be
set by connecting a cable. (P30)
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• [Off] is the factory default.
123
Setting Various Functions
Main Unit and Remote
Control Channel Settings
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
[Remote control]
HDMI
Component
Digital PC
Analog PC
• The factory default is [Independent] for
both projector and remote control.
• After changing the channel on the menu,
be sure to change the channel of the
remote control too.
• If a cable is connected, it is not necessary
to perform remote control channel setting.
When using multiple projectors at the
same time (maximum 4), you can assign a
different channel to each remote control so
that each operates independently.
For the WX6000 / SX6000, set this when
performing infrared operations.
Selecting a Channel on the Remote control
You can change the channel on the
remote control as follows.
Select the main unit channel.
MENU > [System settings] > [Remote control]
MENU > [System settings] > [Remote control]
Ch1
Ch2
Ch3
Ch4
Select the remote control
channel to use with this
projector.
Independent
Remote controls set to any
channel can be used.
124
Ch1
Press and hold the OK button
and [ ] button at the same time
for 3 seconds.
Ch2
Press and hold the OK button
and [ ] button at the same time
for 3 seconds.
Ch3
Press and hold the OK button
and [ ] button at the same time
for 3 seconds.
Ch4
Press and hold the OK button
and [ ] button at the same time
for 3 seconds.
Independent
Press and hold the OK button
and MENU button at the same
time for 3 seconds.
Ch1
Press and hold the Ch button
and 1 button at the same time
for 3 seconds.
Ch2
Press and hold the Ch button
and 2 button at the same time
for 3 seconds.
Ch3
Press and hold the Ch button
and 3 button at the same time
for 3 seconds.
Ch4
Press and hold the Ch button
and 4 button at the same time
for 3 seconds.
Independent
Independent Press and hold the
Ch button and 0 button at the
same time for 3 seconds.
Setting Various Functions
Selecting a Display Language
[Language]
HDMI
Component
Digital PC
Analog PC
You can select the language in which the
menus are displayed.
MENU > [System settings] > [Language]
User’s Manual
Use the [ ] / [ ] / [ ] / [ ] buttons to
select the menu language, then press the
OK button.
English
German
Setting Functions from Menus
French
Italian
Spanish
Portuguese
Swedish
Russian
Dutch
Finnish
Norwegian
Turkish
Polish
Hungarian
Czech
Danish
Arabic
Chinese (Simplified)
Chinese (Traditional)
Korean
Japanese
When the setting is completed, press the
OK button to accept your setting and then
press the MENU button or EXIT button
(WX6000 / SX6000).
125
Setting Various Functions
Showing / Hiding the
Guide Screen
- No input signal can be detected. (P58)
- An invalid button is pressed in the
[BLANK], [FREEZE] or [D.ZOOM]
mode. (P82, P84)
- When the positional lock (P139) is set to
[On] (WX6000 / SX6000)
[Guide]
HDMI
Component
Digital PC
Analog PC
You can select whether to show or hide the
guide screen which explains operations.
MENU > [System settings] > [Guide]
MENU > [Install settings] > [On screen] >
[Guide]
Off
Hides the guide screen.
On
Shows the guide screen.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• [On] is the factory default.
• The guide screen is shown at the following
times.
- Power is turned off by pressing the
POWER button. (P80)
126
Setting Various Functions
Showing / Hiding the
Input Status
Selecting the HDMI Input
[HDMI In]
[Show Input Status]
HDMI
Component
Digital PC
Analog PC
You can select whether the signal status is
displayed on the screen when there is no
signal or when making signal settings.
HDMI
Component
Digital PC
Analog PC
Set the type of equipment which is connected to the HDMI port.
MENU > [System settings] > [HDMI In]
MENU > [System settings] > [Show Input Status]
User’s Manual
MENU > [System settings] > [HDMI In]
Off
The input status is not displayed.
On
The input status is displayed.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• [On] is the factory default.
Auto
Select when AV equipment will
be connected. Image processing, menu displays, and
other elements are adjusted
for video equipment.
Computer
Select when a computer will be
connected. Image processing,
menu displays, and other elements are adjusted for a computer.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
127
Setting Functions from Menus
MENU > [Install settings] > [On screen] > [Show
input status]
Setting Various Functions
Setting a Password
SX6000, the password can be entered
using a combination of the numerical buttons and the [ ] / [ ] / [ ] / [ ] buttons.
[ ] / [1], [ ] / [2], [ ] / [3], and [ ] / [4]
have the same function.
If the password is valid, the projection
starts. If you enter a wrong password three
times, the power will be turned off.
[Password settings]
HDMI
Component
Digital PC
Analog PC
Disables the projector unless the correct
password is entered.
• The power is also turned off if no password
is input for 3 minutes.
MENU > [System settings] > [Other settings] >
[Password settings]
T o C ancel the P assw ord
Turn off the projector and unplug the power
plug.
Hold down the MENU button on the side control
and connect the power plug. Make sure to keep
holding down the MENU button until a beep
sounds. When the beep sounds, the password
is canceled. (The entered password is also
reset.)
To forcibly cancel the password from the remote
control, in standby state press the MENU button
3 times, then press the POWER button.
MENU > [System settings] > [Other settings] >
[Password settings]
Off
On
The projector can be used even if no password is entered.
The projector cannot be used unless you
enter your password.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• [Off] is the factory default.
• You cannot set [On] unless you have completed [Register password].
Once you set a password, the password
entry screen appears at power-on.
Enter a 4 digit password.
For the WUX5000 / WUX4000, the password can be entered using the [ ] / [ ] /
[ ] / [ ] buttons. For the WX6000 /
128
Setting Various Functions
Registering a Password
[Register password]
HDMI
Component
Digital PC
Analog PC
You can register a password for starting
projection.
MENU > [System settings] > [Other settings] >
[Register password]
Enter a 4 digit password.
For the WUX5000 / WUX4000, the password can be entered using the [ ] / [ ] /
[ ] / [ ] buttons. For the WX6000 /
SX6000, the password can be entered
using a combination of the numerical buttons and the [ ] / [ ] / [ ] / [ ] buttons.
[ ] / [1], [ ] / [2], [ ] / [3], and [ ] / [4]
have the same function.
The 4-digit password is entered from the
left to right digits. When the final digit is
entered, the password is automatically
registered.
User’s Manual
• Press the MENU button to abort the registration.
Setting Functions from Menus
MENU > [System settings] > [Other settings] >
[Register password]
Press the OK button after selecting [Register password], and the following screen
for registering a password appears.
129
Setting Various Functions
Prohibiting Operation of
the Lens
[Lens Ctrl Lock]
HDMI
Component
Digital PC
Analog PC
You can lock lens-related button operations.
MENU > [System settings] > [Other settings] >
[Lens Ctrl Lock]
Off
Focus, zoom, lens shift, and other
lens-related operations are permitted.
On
Focus, zoom, lens shift, and other
lens-related operations are locked.
Press the OK button to accept your setting
and then press the MENU button.
• [Off] is the factory default.
130
Setting Various Functions
Lens Shift Reset
[Lens shift Reset]
HDMI
Component
Digital PC
Analog PC
Resets the lens shift (P74) setting to the
standard position.
• The standard position varies depending
on the type of lens unit used. For details,
refer to page 75.
• The position which was adjusted by lens
shift does not change when the power is
turned off.
MENU > [System settings] > [Other settings] >
[Lens shift Reset]
User’s Manual
Setting Functions from Menus
MENU > [Install settings] > [Lens shift Reset]
Select [Lens shift Reset] and press the OK
button. The following screen for confirmation appears.
Use the [ ] / [ ] buttons to select the
standard position, and then select OK.
131
Setting Various Functions
Extending the Menu Display Time
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
[Menu display time]
HDMI
Component
Digital PC
Analog PC
• [Normal] is the factory default.
• The following display and operation are also
changed.
The setting for the menu display time can
be extended from the normal 10 or 30 seconds to 3 minutes. For the WUX5000 /
WUX4000, if [Extended] is set, when pushing and holding a button on the projector or
remote control, the same key repeat function will be enabled as when pressing a
button repeatedly.
MENU > [System settings] > [Other settings] >
[Menu display time]
Item
*1 WUX4000
*2 WX6000 / SX6000
MENU > [Install settings] > [On screen] > [Menu
display time]
Normal
The menu is displayed for 10 or 30 seconds.
Extended The menu is displayed for 3 minutes.
132
[Normal] [Extended]
The display time of the following
screens
-MENU screen
-Input (P60)
-Zoom adjustment (P71)
-Focus adjustment (P73)
-Keystone adjustment (P76)
-Keystone reset (P77)
10 / 30
-D.image shift adjustment (P67, P68) seconds
-D.image shift reset (P69)
-Aspect (P70)
-Image mode (P78)
-Volume adjustment (P83)
-Lamp mode (P119) *1
-Lens shift (P74)
-Lens shift reset (P131)
Press-and-hold operation of
pointer buttons other than for
[Zoom adjustment], [Focus
adjustment], and [Lens shift]
Enabled
Press-and-hold operation of
VOL button
Press-and-hold operation of the
D.ZOOM button
Key repeat *2
[On]
3 minutes
Disabled
[Off]
Setting Various Functions
Showing / Hiding the High
Temperature Warning Icon
played when the temperature inside the
projector is abnormally high.
[Overheat Warning Display]
HDMI
Component
Digital PC
Analog PC
You can select whether or not to display
the [High temperature warning] icon when
the temperature inside the projector has
increased and is approaching the overheat
temperature.
Screen
• [Off] is the factory default.
User’s Manual
MENU > [System settings] > [Other settings] >
[Overheat Warning Display]
Setting Functions from Menus
MENU > [Install settings] > [On screen] > [Overheat warning display]
Off
The [High temperature warning] icon is
not displayed.
On
The [High temperature warning] icon is
displayed.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
When [On] is set, the [High temperature
warning] icon shown below will be dis133
Setting Various Functions
Reducing Flickering
Gamma Restore
[Deflicker]
[Gamma restore]
HDMI
Component
Digital PC
Analog PC
HDMI
Digital PC
This function is used when changing and
turning of the tone characteristics and achromatic color is noticed over a long period
of time.
This function adjusts the image display in
order to reduce flickering in the projected
image.
MENU > [System settings] > [Other settings] >
[Deflicker]
Off
Component
Analog PC
MENU > [System settings] > [Other settings] >
[Gamma restore]
Deflicker adjustment is not performed.
Off
Returns to the factory default without performing Gamma restore.
Adjust
Performs Gamma restore and
applies the result.
Adjust Select [Deflicker] to adjust. The following screen appears.
OK
Deflicker is performed.
Cancel
Deflicker is not performed.
• When deflicker is performed, the image
adjustment screen is projected for approximately 20 seconds.
• To cancel deflicker, press the POWER
button.
• Deflicker is a function that decreases
flickering. However, there are some
cases that flickering continues.
• Deflicker can only be used when the
lamp has been on for approximately
30 minutes or longer.
134
OK
Gamma Restore is performed.
Cancel
Gamma Restore is not
performed.
If Gamma restore is performed, the projected image will be adjusted for a period
of approximately 150 seconds.
• To stop Gamma restore, press the POWER
button or the EXIT button (WX6000 /
SX6000).
• If Gamma restore is performed, the
tone characteristics and achromatic
color will be restored as close as
possible to the condition when the
unit was purchased, however it is not
possible to restore it completely to
the original condition. So the changing and turning color cannot be eliminated completely.
• Gamma restore can only be used
when the lamp has been on for
approximately 30 minutes or longer.
Setting Various Functions
Lamp Warning Display
[Lamp warning display]
HDMI
Digital PC
Component
Analog PC
A message that advises you to change the
lamp can be set to display when the lamp
has been used for the specified period of
time.
Resetting the Lamp
Counter
[Lamp counter]
HDMI
Component
Digital PC
Analog PC
You can reset the lamp counter that indicates the time for lamp replacement.
MENU > [System settings] > [Other settings] >
[Lamp counter]
The lamp warning display is not
displayed.
On
The prepare lamp message and
the lamp warning display are displayed.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• The factory default is [On].
• Regardless of the [Lamp warning display]
setting, when the lamp replacement time has
been reached, the LAMP indicator on the
projector will flash.
MENU > [System settings] > [Other settings] >
[Lamp counter]
135
Setting Functions from Menus
Off
User’s Manual
Do not reset the lamp counter except
when you have replaced the lamp.
Otherwise, the lamp counter cannot
indicate the correct timing for replacing the lamp.
For details of lamp replacement, refer
to page 195.
MENU > [Install settings] > [On screen] > [Lamp
warning display]
Setting Various Functions
Select [Lamp counter] and press the OK
button to display the lamp counter.
When the lamp hours are 2,700 hours to
less than 3,000 hours, the message
“Obtain a new lamp.” appears when
power is turned on.
Select [Reset] and press the OK button.
Over 3,000 hours
Displayed as a green, yellow and red
bar.
Select [OK] on the screen for confirmation
and press the OK button to reset the lamp
counter.
Press the MENU button or EXIT button
(WX6000 / SX6000).
The message “Replace with the new
lamp.” appears when power is turned on.
■ About the Display of the Lamp
Counter
The lamp counter displays the hours of
use of the lamp in the following way.
Less than 2,700 hours
Displayed as a green bar.
2,700 hours to less than 3,000 hours
Displayed as a green and yellow bar.
136
Setting Various Functions
Filter Warning Display
[Filter warning display]
HDMI
Digital PC
Component
Analog PC
A message advising you to perform cleaning can be set to display when the filter
needs cleaning.
MENU > [Install settings] > [On screen] > [Filter
warning display]
Resetting the Air Filter
Counter
[Filter counter]
HDMI
Component
Digital PC
Analog PC
This resets the counter which reminds you
of the time for cleaning and replacing the
air filter.
For details about how to replace or
clean the filter, refer to page 193.
The filter warning display is not
displayed.
On
The filter warning display is displayed.
If the OK button is pressed on [Filter
counter], the air filter counter is displayed.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• The factory default is [On].
Select [Reset] and press the OK button.
[OK] is selected on the confirmation
screen and the OK button is pressed, the
air filter counter is reset.
Press the MENU button or EXIT button
(WX6000 / SX6000).
137
Setting Functions from Menus
Off
User’s Manual
MENU > [System settings] > [Other settings] >
[Filter counter]
Setting Various Functions
Displaying Test Pattern
The following functions in the [Image
adjustment] tab are not applied to the
test pattern.
• Brightness adjustment function
(P111)
• Contrast adjustment function (P112)
• Sharpness adjustment function
(P113)
• Color level adjustment function
(P114)
• Color balance adjustment function
(P114)
[Test pattern]
HDMI
Digital PC
Component
Analog PC
A test pattern for checking the resolution
and color when installing the projector can
be displayed.
MENU > [Install settings] > [Test pattern]
Off
The test pattern is not displayed.
On
The test pattern is displayed.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• The factory default is [Off].
• While the test pattern is displayed, you can
use the [ ] / [ ] buttons to change to a different test pattern. Also, if a test pattern has
option settings, you can change the settings
using the [ ] / [ ] button. (P217)
• The test pattern can also be displayed or
turned off by pressing the TEST PATTERN
button on the remote control.
138
Setting Various Functions
Selecting Audio In Terminal
Locking Installation
Related Functions
[Audio in terminal select]
[Positional lock]
HDMI
Digital PC
Component
Analog PC
You can select the audio in terminal that is
used for each input signal (HDMI, Digital
PC, Analog PC-1, Analog PC-2, Component).
HDMI
Digital PC
Component
Analog PC
Operation of installation related functions
can be prohibited.
MENU > [Install settings] > [Positional lock]
User’s Manual
MENU > [Install settings] > [Audio in terminal
select]
No audio is output.
Off
The positional lock is not used.
Audio in 1
Outputs the audio signal that
is inputted in Audio in terminal
1.
On
Installation related functions cannot be used.
Audio in 2
Outputs the audio signal that
is inputted in Audio in terminal
2.
HDMI
Outputs the HDMI audio signal. (Only for HDMI)
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• The factory default is [Off].
• The positional lock can be applied to Test
pattern display, Screen aspect settings, Keystone adjustment, Digital image shift adjustment, Image flip H/V, Focus adjustment,
Zoom adjustment, Lens shift adjustment and
Lens shift reset.
• The factory default is as follows.
HDMI: HDMI
Digital PC: Audio in 2
Analog PC-1: Audio in 1
Analog PC-2: Audio in 2
Component: Audio in 1
139
Setting Functions from Menus
Off
Setting Various Functions
Resetting to the Default Setting
• This function does not reset the values for
[Lamp counter], [Language], [Remote control], [Input signal], [Network Setting], [Filter
counter], [Focus position], [Zoom position],
and [Lens shift position].
• For factory defaults settings, refer to pages
232 – 238.
• The contents of the user memory return to the
conditions at the time it was saved. (P110)
[Factory defaults]
HDMI
Component
Digital PC
Analog PC
You can reset the menu item settings and
restore the system settings to the factory
defaults.
MENU > [System settings] > [Other settings] >
[Factory defaults]
MENU > [System settings] > [Other settings] >
[Factory defaults]
Select [Factory defaults] and press the OK
button. The following screen for confirmation appears.
OK
Settings are reset to default.
Cancel
Settings are not reset to default.
140
Checking Projector Information
[Information]
HDMI
Component
Digital PC
Analog PC
You can check information about the
signal types of the images projected and other
information.
MENU > [Information]
MENU > [Information]
User’s Manual
Item
Meaning
Model name
WUX5000 / WUX4000 / WX6000 / SX6000
Input signal
Details of the input signal currently selected
Information such as the signal type, signal resolution, and frequency
is displayed.
Firmware
Current firmware version
Serial No.
Serial number unique to this projector
IP address*
IP address of the projector (P175)
Gateway address*
IP address of the gateway device (P175)
E-mail sender address*
Sender e-mail address used for sending error mails (P183)
E-mail recipient
address*
Displays [Already set] or [Not set] to show whether a recipient e-mail
address has been set for receiving error mails. (P183)
Projector name*
Name which identifies this projector on the network
Location*
Location where the projector is installed
System information ID
System information. Normally this is not displayed.
* Not displayed when network functions are [Off].
141
Setting Functions from Menus
Information shown
142
MULTIMEDIA PROJECTOR
Installation Manual
(Installation and
Maintenance)
Do not attempt installation yourself. Be sure to
request installation from a qualified technician or
contact the Canon Customer Support Center.
143
144
Table of Contents
Safety Instructions
Installation
Before Use
Projecting an Image
User’s Manual
Useful Functions Available
During a Presentation
Setting Functions from Menus
Installation Manual
Installation
Connecting to a Network
Maintenance
Appendix
Appendix
Index
145
Installation Precautions
Precautions When Carrying the Projector
Prepare the projector as described below before carrying it.
• Disconnect the cables connected to the projector. Carrying
the projector with the cables attached may cause an accident.
• Retract the adjustable feet.
• When the projector is transported after the lens unit is
installed, be sure that you do not grasp the lens while transporting it. Doing so may damage the projector.
Installation Precautions
Be sure to read on page 12 – 24. Pay attention to the following when installing the
projector.
• Do not strike the projector or
Intake
subject it to impact. Doing so
may cause a malfunction.
• Do not install the projector so
that it is inclined or standing
vertically. The projector may tip
Exhaust
over, causing damage.
• Do not block the cooling fan
intake or exhaust vent. If the intake or exhaust vent is
blocked, heat may accumulate inside the projector, causing
a malfunction.
Precautions When Carrying and Transporting the Projector
• Do not reuse any packaging or shock-absorbent materials
that were supplied with the projector at the time of purchase
for transporting or shipping the projector. Protection of the
projector cannot be guaranteed if used packaging or shockabsorbent materials are reused. Fragments from shockabsorbent material may also enter the interior of the projector which could cause a malfunction.
• If transportation is necessary, the lens unit should be
removed before transporting the projector. If the projector is
subjected to excessive impacts during transportation, the
lens unit may be damaged. Removal and installation of the
lens unit should not be performed by the user. Be sure to
have the procedure performed by a qualified technician or
contact the Canon Customer Support Center.
146
Installation Precautions
■ Do Not Use in the Following Environments
• Do not install the projector in a humid or dusty location or a position where there is a lot
of oily smoke or cigarette smoke. Optical parts such as the lens and mirror may be
stained, resulting in poor picture quality.
• Do not install close to high-voltage power lines or power sources. The projector may not
operate correctly.
• Do not use the projector on a soft surface such as a carpet or sponge mat. Heat may
accumulate inside the projector, causing a malfunction.
• Do not use the projector in a location that is subject to very high temperatures, very low
temperatures, or high levels of humidity. Doing so may cause a malfunction. The temperature and humidity ranges for operation and the temperature range for storage are
shown below.
Operating
humidity
Storage
temperature
5°C to 35°C
Up to 85%
-10°C to 60°C
■ Do Not Touch the Lens with Bare Hands
Do not touch the lens with bare hands. Doing so may adversely affect picture quality.
■ Install at a Sufficient Distance from Walls and Other Obstructions
Air intake vent
Exhaust vent
Warmed airflow
50 cm
(1.6')
50 cm
(1.6')
50 cm
(1.6')
50 cm
(1.6')
■ Be Careful of Condensation
If the temperature of the room rises suddenly, moisture in the air may condense on the
projector lens and mirror, causing the image to become blurred. Wait until condensation
evaporates and a normal picture is shown.
■ When Using the Projector at Altitudes Greater than 2,300 m
Contact the Canon Customer Support Center if you intend to use this projector at altitudes
of 2,300 m or higher.
147
Installation
If the air intake or
exhaust vent is blocked,
heat will accumulate
inside the projector,
possibly resulting in a
shortened projector lifetime or a malfunction.
Do not install in a
closet, on a bookshelf,
or other narrow location
with poor ventilation.
Install in a well ventilated location. (Install
with a minimum of 50
cm (1.6') clearance on
the top and sides, and
50 cm (1.6') to the rear.)
Installation Manual
Operating
temperature
Installation Precautions
■When using mounted on the ceiling
When the projector is used mounted on the
ceiling or installed in a high location, it is necessary to periodically clean the air intake and
exhaust vents, and the area around the air filter. If dust accumulates in the intake or
exhaust vents, cooling performance will deteriorate, causing the internal temperature to rise and possibly resulting in a
malfunction or fire. Use a vacuum cleaner or similar means to remove dust
from the intake vent and exhaust vent.
■Install facing in the correct direction
This projector can be installed in directions of 360° *1 as shown in the
illustration below. However, if projecting upward
or downward , the
life span of the lamp may be shortened, and it is necessary to change the
settings of the projector. If using the projector for upward or downward
projection, please contact the Canon Customer Support Center.
10° 10°
10° 10°
Downward projection:
Inclination of the
projector should be
no more than 10°
from the vertical
axis. *2
Upward projection:
Inclination of the
projector should be
no more than 10°
from the vertical
axis. *2
10°
10°
If installing the projector on the floor or
hanging from the ceiling, the left / right inclination of the projector
should be no more
than 10°. *2
Do not use the projector
standing on its side. *2
*1 There are no options for installing the projector other than the ceiling attachment. (P33, P150, P231)
*2 This may damage the lamp.
148
Installation Procedure
Selecting the Projection Method and
Installation Location (P150)
Installing / Removing the Lens Unit (P151)
Setting Up the Projector (P156)
Adjusting the Image (P61)
Connecting to a Network (P165)
149
Installation
Selecting an Input Signal (P59)
Installation Manual
Connecting to AV Equipment (P162)
Selecting the Projection Method and Installation Location
■Ceiling Mounting or Rear Projection
You can mount the projector on the ceiling (ceiling mounting) with it turned upside down
or place it behind the screen (rear projection) if you use a translucent screen.
Ceiling Mounting
Rear Projection
Make sure to use the optional ceiling attachment. For the ceiling attachment, refer to
page 231.
■Adjusting the projection position when installed on the floor
To adjust the projection position when the projector is installed on the floor, use the lens
shift function (P74 and P160) to adjust up / down / left / right. You can also use the adjustable feet to incline the projector upward by up to 6°. For information about the relationship
between screen size and projection distance, refer to page 156.
Adjustable feet
Lens shift
When the projector is inclined upwards, the projected image will be distorted into a trapezoid shape. This can be corrected by using the keystone correction. (P76)
150
Installing / Removing the Lens Unit
■Installing the Lens Unit
Before installing or removing the lens unit, be sure to disconnect
the power plug or connector. Failure to do so may result in fire,
electric shock, or injury.
1
Use a Phillips-head screwdriver and loosen the lamp cover screw, then open the lamp
cover.
The lamp cover screw is attached to the lamp cover and designed to prevent it from
falling off.
Screw
151
Installation
• Do not attempt to install or remove the lens unit yourself. Be
sure to request this service from a qualified technician or contact the Canon Customer Support Center.
• When installing and removing the lens unit, be sure not to
touch the surface of the lens with your hands or scratch it.
• Do not apply force to parts (e.g. lead wires) that are connected
to the lens unit or lens motor. Doing so may cause a malfunction.
• Do not replace the lens unit in a dusty location. If any dust or
dirt enters the projector, this may adversely affect picture
quality.
• For details about which devices the projector is compatible
with, contact the Canon Customer Support Center.
Installation Manual
• Before replacing the lens unit, make sure to turn off the projector, wait at least 1 hour to allow the projector to cool thoroughly. Failure to do so may result in burns or other injuries.
• Do not touch the lens when the lens is moving (the lens is
shifting) to adjust the projected image after installation. There
is the risk of injury.
• When hanging the projector from a ceiling, put the projector
down on the floor or a workbench before attaching or replacing the lens unit. Failure to do so could result in parts falling
off the projector and may cause an accident or personal
injury.
Installing / Removing the Lens Unit
2
Loosen the cosmetic panel screw, then slide the cosmetic panel toward the rear to
remove it.
The cosmetic panel screw is attached to the cosmetic panel and designed to prevent
it from falling off.
3
In order to prevent damage, close the lamp cover and temporarily fasten the screw.
4
Remove the sleeve screws (2 on top and 2 on bottom).
After the 2 screws on top are removed, turn the projector upside down on a flat desk
or similar location and remove the 2 screws from the bottom.
152
Installing / Removing the Lens Unit
5
Then turn the projector back over and remove the sleeve.
6
Referring to the following illustration, insert the lens connector of the lens unit into the
front right side of the projector slowly until it contacts the end. At this time, pull out the
lens cable shown in the illustration and fix it.
7
Tighten the 4 screws to fasten the lens unit in place.
The 4 lens unit screws are attached to the lens unit and cannot be removed.
153
Installation
Lens connector
Installation Manual
Lens cable
Installing / Removing the Lens Unit
8
Insert the projector lens cable into the connector until a click sound is heard.
9
Reinstall the sleeve, cosmetic panel, and lamp cover in their original positions.
When the power is first turned on after the lens unit has been installed or replaced, lens shift
initialization operation will be performed. It will take approximately 1 minute for the initialization operation to start up. However, if the lens has been replaced with a lens of the same
model number, initialization operation will not be performed. The position will be the same as
before the lens was replaced.
The lens shift initialization operation uses the motor to move
the lens up / down / left / right. Do not touch the lens. Doing so
could result in an injury.
When installing and removing the lens unit, be sure to fix the
lens cable as shown in the illustration. When inserting the lens
unit, it is possible to damage the lens cable between the lens
unit and projector.
154
Installing / Removing the Lens Unit
■Removing the Lens Unit
1
2
Perform steps 1 to 5 on pages 151 – 153 and remove the sleeve.
Disconnect the lens cable from the lens connector.
When pulling out (disconnecting) the lens cable, press the buttons on both sides of the lens
cable connector while pulling out the cable.
155
Installation
Fix the lens cable as shown in the illustration and loosen the 4 screws to remove the
lens unit.
The 4 lens unit screws are attached to the lens unit and cannot be removed.
Installation Manual
3
Setting Up the Projector
■Positioning the Projector in Front of the Screen
Place the projector in front of the screen.
• Be sure to place the projector parallel
to the screen to ensure distortion-free
projection.
• The screen must not be exposed to
direct sunlight or light from lighting
equipment. In a bright room, it is recommended that lights be turned off,
curtains be drawn, and other steps
taken to make the screen easier to see.
Screen
Optical axis
■Relationship Between Image Size and Projecting Distance
The projected image size is determined by the distance between the projector and the
screen (projection distance) as well as the zoom. Refer to the following table and decide
the distance between the projector and screen.
Height
16:9 / 16:10
16:9/16:10
Screen size
(diagonal)
Height
4:3
Width
Width
Optical axis when projection is perpendicular to screen
H1
H2
Screen
• H1 and H2 are the distances when lens shift is the default value below.
• Standard Zoom Lens / Long Zoom Lens / Ultra Long Zoom Lens:
+50% (up / down), 0% (left / right)
Short Fixed Lens: 0% (up / down / left / right)
156
Setting Up the Projector
WUX5000 / WUX4000
Lens unit
Standard
Zoom Lens
RS-IL01ST
Ultra long
Zoom Lens
RS-IL04UL
16:10
16:9
4:3
16:10
40
60
80
100
150
200
250
300
350
400
450
500
550
600
40
60
80
100
150
200
250
300
350
400
450
500
550
600
40
60
80
100
Width
86
129
172
215
323
431
538
646
754
862
969
1077
1185
1292
86
129
172
215
323
431
538
646
754
862
969
1077
1185
1292
86
129
172
215
Height
54
81
108
135
202
269
337
404
471
538
606
673
740
808
54
81
108
135
202
269
337
404
471
538
606
673
740
808
54
81
108
135
Width
86
129
172
215
323
431
538
646
754
862
969
1077
1185
1292
86
129
172
215
323
431
538
646
754
862
969
1077
1185
1292
86
129
172
215
Height
48
73
97
121
182
242
303
363
424
484
544
605
666
726
48
73
97
121
182
242
303
363
424
484
544
605
666
726
48
73
97
121
Width
72
108
144
179
269
359
449
538
628
718
808
898
987
1076
72
108
144
179
269
359
449
538
628
718
808
898
987
1076
72
108
144
179
Height
54
81
108
135
202
269
337
404
471
538
606
673
740
808
54
81
108
135
202
269
337
404
471
538
606
673
740
808
54
81
108
135
Wide limit
Tele limit
1.3 (4.3)
1.9 (6.2)
1.9 (6.2)
2.9 (9.5)
2.6 (8.5)
3.9 (12.8)
3.2 (10.5)
4.8 (15.7)
4.8 (15.7)
7.2 (23.6)
6.4 (21.0)
9.6 (31.5)
8.0 (26.2) 12.1 (39.7)
9.6 (31.5) 14.5 (47.6)
11.3 (37.1) 16.9 (55.4)
12.9 (42.3) 19.3 (63.3)
14.5 (47.6) 21.7 (71.2)
16.1 (52.8) 24.1 (79.1)
17.7 (58.1) 26.6 (87.3)
19.3 (63.3) 29.0 (95.1)
1.9 (6.2)
3.2 (10.5)
2.8 (9.2)
4.8 (15.7)
3.8 (12.5)
6.4 (21.0)
4.7 (15.4)
8.0 (26.2)
7.1 (23.3) 12.1 (39.7)
9.5 (31.2) 16.1 (52.8)
11.9 (39.0) 20.2 (66.3)
14.2 (46.6) 24.2 (79.4)
16.6 (54.5) 28.3 (92.8)
19.0 (62.3) 32.3 (106.0)
20.9 (68.6) 35.6 (116.8)
23.8 (78.1) 40.4 (132.5)
26.1 (85.6) 44.5 (146.0)
28.5 (93.5) 48.5 (159.1)
0.7 (2.3)
1.0 (3.3)
1.4 (4.6)
1.7 (5.6)
150
200
250
300
40
60
80
100
150
200
250
300
350
400
450
500
550
600
323
431
538
646
86
129
172
215
323
431
538
646
754
862
969
1077
1185
1292
202
269
337
404
54
81
108
135
202
269
337
404
471
538
606
673
740
808
323
431
538
646
86
129
172
215
323
431
538
646
754
862
969
1077
1185
1292
182
242
303
363
48
73
97
121
182
242
303
363
424
484
544
605
666
726
269
359
449
538
72
108
144
179
269
359
449
538
628
718
808
898
987
1076
202
269
337
404
54
81
108
135
202
269
337
404
471
538
606
673
740
808
2.6 (8.5)
3.4 (11.2)
4.3 (14.1)
5.2 (17.1)
157
–
4.6 (15.1)
6.1 (20.0)
7.6 (24.9)
11.4 (37.4)
15.2 (49.7)
18.9 (62.0)
22.7 (74.5)
26.4 (86.6)
30.2 (99.1)
34.0 (111.5)
37.7 (123.7)
41.5 (136.2)
45.2 (148.3)
–
9.0 (29.5)
12.0 (39.4)
14.9 (50.2)
22.3 (77.3)
29.8 (97.8)
37.2 (122.0)
44.6 (146.3)
52.0 (170.6)
59.4 (194.9)
66.8 (219.2)
74.2 (243.4)
81.6 (267.7)
89.0 (292.0)
Distance from optical
axis when projection is
perpendicular to
screen* (cm)
H1
H2
54
0
81
0
108
0
135
0
202
0
269
0
337
0
404
0
471
0
538
0
606
0
673
0
740
0
808
0
54
0
81
0
108
0
135
0
202
0
269
0
337
0
404
0
471
0
538
0
606
0
673
0
740
0
808
0
27
27
41
41
54
54
68
68
101
135
168
202
54
81
108
135
202
269
337
404
471
538
606
673
740
808
101
135
168
202
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Installation
Short Fixed
Lens
RS-IL03WF
Projection distance
m (feet)
Image size (cm)
Installation Manual
Long Zoom
Lens
RS-IL02LZ
Diagonal
when
16:10
Setting Up the Projector
WX6000
Lens unit
Standard
Zoom Lens
RS-IL01ST
Long Zoom
Lens
RS-IL02LZ
Short Fixed
Lens
RS-IL03WF
Ultra long
Zoom Lens
RS-IL04UL
Diagonal
when
16:10
Projection distance
m (feet)
Image size (cm)
16:10
16:9
4:3
16:10
40
60
80
100
150
200
250
300
350
400
450
500
550
600
40
60
80
100
150
200
250
300
350
400
450
500
550
600
40
60
80
100
Width
86
129
172
215
323
431
538
646
754
862
969
1077
1185
1292
86
129
172
215
323
431
538
646
754
862
969
1077
1185
1292
86
129
172
215
Height
54
81
108
135
202
269
337
404
471
538
606
673
740
808
54
81
108
135
202
269
337
404
471
538
606
673
740
808
54
81
108
135
Width
86
129
172
215
323
431
538
646
754
862
969
1077
1185
1292
86
129
172
215
323
431
538
646
754
862
969
1077
1185
1292
86
129
172
215
Height
48
73
97
121
182
242
303
363
424
484
544
605
666
726
48
73
97
121
182
242
303
363
424
484
544
605
666
726
48
73
97
121
Width
72
108
144
179
269
359
449
538
628
718
808
898
987
1076
72
108
144
179
269
359
449
538
628
718
808
898
987
1076
72
108
144
179
Height
54
81
108
135
202
269
337
404
471
538
606
673
740
808
54
81
108
135
202
269
337
404
471
538
606
673
740
808
54
81
108
135
Wide limit
Tele limit
1.3 (4.3)
2.0 (6.6)
2.0 (6.6)
3.0 (9.8)
2.6 (8.5)
4.0 (13.1)
3.3 (10.8)
4.9 (16.1)
4.9 (16.1)
7.4 (24.3)
6.6 (21.6)
9.9 (32.5)
8.2 (26.9) 12.4 (40.7)
9.9 (32.5) 14.9 (48.9)
11.5 (37.7) 17.3 (56.8)
13.2 (43.3) 19.8 (65.0)
14.9 (48.9) 22.3 (73.2)
16.5 (54.1) 24.8 (81.4)
18.2 (59.7) 27.2 (89.2)
19.8 (65.0) 29.7 (97.4)
1.9 (6.2)
3.3 (10.8)
2.9 (9.5)
4.9 (16.1)
3.9 (12.8)
6.6 (21.6)
4.8 (15.7)
8.3 (27.2)
7.3 (23.9) 12.4 (40.7)
9.7 (31.8) 16.6 (54.5)
12.2 (40.0) 20.7 (67.9)
14.6 (47.9) 24.9 (81.7)
17.1 (56.1) 29.0 (95.1)
19.5 (64.0) 33.1 (108.6)
21.9 (71.8) 37.3 (122.4)
24.4 (80.1) 41.4 (135.8)
26.8 (87.9) 45.6 (149.6)
29.3 (96.1) 49.7 (163.1)
0.7 (2.3)
1.1 (3.6)
1.4 (4.6)
1.8 (5.9)
150
200
250
300
40
60
80
100
150
200
250
300
350
400
450
500
550
600
323
431
538
646
86
129
172
215
323
431
538
646
754
862
969
1077
1185
1292
202
269
337
404
54
81
108
135
202
269
337
404
471
538
606
673
740
808
323
431
538
646
86
129
172
215
323
431
538
646
754
862
969
1077
1185
1292
182
242
303
363
48
73
97
121
182
242
303
363
424
484
544
605
666
726
269
359
449
538
72
108
144
179
269
359
449
538
628
718
808
898
987
1076
202
269
337
404
54
81
108
135
202
269
337
404
471
538
606
673
740
808
2.7 (8.9)
3.5 (11.5)
4.4 (14.4)
5.3 (17.4)
158
–
4.8 (15.7)
6.3 (20.7)
7.8 (25.6)
11.7 (38.4)
15.6 (51.2)
19.4 (63.6)
23.3 (76.4)
27.1 (88.9)
31.0 (101.7)
34.8 (114.2)
38.7 (127.0)
42.5 (139.4)
46.4 (152.2)
–
9.2 (30.2)
12.3 (40.4)
15.3 (50.2)
22.9 (75.1)
30.5 (100.1)
38.1 (125.0)
45.7 (149.9)
53.3 (174.9)
60.9 (199.8)
68.5 (224.7)
76.1 (249.7)
83.7 (274.6)
91.3 (299.5)
Distance from optical
axis when projection is
perpendicular to
screen* (cm)
H1
H2
54
0
81
0
108
0
135
0
202
0
269
0
337
0
404
0
471
0
538
0
606
0
673
0
740
0
808
0
54
0
81
0
108
0
135
0
202
0
269
0
337
0
404
0
471
0
538
0
606
0
673
0
740
0
808
0
27
27
41
41
54
54
68
68
101
135
168
202
54
81
108
135
202
269
337
404
471
538
606
673
740
808
101
135
168
202
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Setting Up the Projector
SX6000
Lens unit
Diagonal
when 4:3
4:3
Standard
Zoom Lens
RS-IL01ST
Ultra long
Zoom Lens
RS-IL04UL
Height
61
91
122
152
229
305
381
457
533
610
686
762
838
914
61
91
122
152
229
305
381
457
533
610
686
762
838
914
61
91
122
152
229
305
381
457
61
91
122
152
229
305
381
457
533
610
686
762
838
914
16:10
Width
81
122
163
203
305
406
508
610
711
813
914
1016
1118
1219
81
122
163
203
305
406
508
610
711
813
914
1016
1118
1219
81
122
163
203
305
406
508
610
81
122
163
203
305
406
508
610
711
813
914
1016
1118
1219
Height
51
76
102
127
191
254
318
381
445
508
572
635
699
762
51
76
102
127
191
254
318
381
445
508
572
635
699
762
51
76
102
127
191
254
318
381
51
76
102
127
191
254
318
381
445
508
572
635
669
762
16:9
Width
81
122
163
203
305
406
508
610
711
813
914
1016
1118
1219
81
122
163
203
305
406
508
610
711
813
914
1016
1118
1219
81
122
163
203
305
406
508
610
81
122
163
203
305
406
508
610
711
813
914
1016
1118
1219
159
Height
46
69
91
114
171
229
286
343
400
457
514
572
629
686
46
69
91
114
171
229
286
343
400
457
514
572
629
686
46
69
91
114
171
229
286
343
46
69
91
114
171
229
286
343
400
457
514
572
629
686
4:3
Wide limit
Tele limit
1.3 (4.3)
1.9 (6.2)
1.9 (6.2)
2.9 (9.5)
2.5 (8.2)
3.8 (12.5)
3.2 (10.5)
4.8 (15.7)
4.8 (15.7)
7.2 (23.6)
6.4 (21.0)
9.6 (31.5)
8.0 (26.2) 12.0 (39.4)
9.6 (31.5) 14.4 (47.2)
11.2 (36.7) 16.8 (55.1)
12.8 (42.0) 19.2 (63.0)
14.4 (47.2) 21.6 (70.9)
16.0 (52.5) 24.0 (78.7)
17.6 (57.7) 26.4 (86.6)
19.2 (63.0) 28.8 (94.5)
1.9 (6.2)
3.2 (10.5)
2.8 (9.2)
4.8 (15.7)
3.7 (12.1)
6.4 (21.0)
4.7 (15.4)
8.0 (26.2)
7.1 (23.3) 12.0 (39.4)
9.4 (30.8) 16.1 (52.8)
11.8 (38.7) 20.1 (65.9)
14.2 (46.6) 24.1 (79.6)
16.5 (54.1) 28.1 (92.2)
18.9 (62.0) 32.2 (105.6)
21.3 (69.9) 36.2 (118.8)
23.7 (77.8) 40.2 (131.9)
26.0 (85.3) 44.2 (145.0)
28.4 (93.2) 48.3 (158.5)
0.7 (2.3)
1.0 (3.3)
1.4 (4.6)
1.7 (5.6)
2.6 (8.5)
3.4 (11.2)
4.3 (14.1)
5.1 (16.7)
–
–
4.6 (15.1)
9.0 (29.5)
6.1 (20.0) 11.9 (39.0)
7.6 (24.9) 14.9 (48.9)
11.3 (37.1) 22.2 (72.8)
15.1 (49.5) 29.6 (97.1)
18.8 (61.7) 37.0 (121.4)
22.6 (74.1) 44.4 (145.7)
26.3 (86.3) 51.7 (169.6)
30.0 (98.4) 59.1 (193.9)
33.8 (110.9) 66.5 (218.2)
37.5 (123.0) 73.8 (242.1)
41.3 (135.5) 81.2 (266.4)
45.0 (147.6) 88.6 (290.7)
Installation
Short Fixed
Lens
RS-IL03WF
Width
81
122
163
203
305
406
508
610
711
813
914
1016
1118
1219
81
122
163
203
305
406
508
610
711
813
914
1016
1118
1219
81
122
163
203
305
406
508
610
81
122
163
203
305
406
508
610
711
813
914
1016
1118
1219
Distance from optical
axis when projection is
perpendicular to
screen* (cm)
H1
H2
61
0
91
0
122
0
152
0
229
0
305
0
381
0
457
0
533
0
610
0
686
0
762
0
838
0
914
0
61
0
91
0
122
0
152
0
229
0
305
0
381
0
457
0
533
0
610
0
686
0
762
0
838
0
914
0
30
30
46
46
61
61
76
76
114
114
152
152
191
191
229
229
61
0
91
0
122
0
152
0
229
0
305
0
381
0
457
0
533
0
610
0
686
0
762
0
838
0
914
0
Installation Manual
Long Zoom
Lens
RS-IL02LZ
40
60
80
100
150
200
250
300
350
400
450
500
550
600
40
60
80
100
150
200
250
300
350
400
450
500
550
600
40
60
80
100
150
200
250
300
40
60
80
100
150
200
250
300
350
400
450
500
550
600
Projection distance
m (feet)
Image size (cm)
Setting Up the Projector
■Lens Shift Function
The projector includes a lens shift function. Operation of the buttons slides the lens up,
down, left, and right, moving the image position. For the function operations, refer to page
74.
The amount of lens shift is indicated as a percentage relative to the image height and
width.
The table below shows the lens shift for each lens.
Standard
Zoom Lens
(RS-IL01ST)
Long Zoom
Lens
(RS-IL02LZ)
Short Fixed
Lens
(RS-IL03WF)
Ultra Long
Zoom Lens
(RS-IL04UL)
WUX5000
WUX4000
WX6000
SX6000
Up (1)
+55%
+55%
+55%
+50%
Down (2)
-15%
-15%
-15%
-12%
Left/right (3)
±10%
±10%
±10%
±10%
+50%
Up (1)
+55%
+55%
+55%
Down (2)
-15%
-15%
-15%
-12%
Left/right (3)
±10%
±10%
±10%
±10%
+5%
Up (1)
+5%
+5%
+5%
Down (2)
-5%
-5%
-5%
-5%
Left/right (3)
±2%
±2%
±2%
±2%
+50%
Up (1)
+55%
+55%
+55%
Down (2)
-15%
-15%
-15%
-12%
Left/right (3)
±10%
±10%
±10%
±10%
Amount movable in up/down
direction
(1)
90°
90°
(2)
At maximum downward lens shift
At maximum upward lens shift
160
Setting Up the Projector
Amount movable in
left/right direction
90°
90°
(3)
At maximum leftward lens shift
At maximum rightward lens shift
2% of projected
image width
(1)
Shift range
2% of projected
image width
Projected
image
With the Short Fixed Lens, greater shift in the up / down direction reduces the available
shift in the left / right direction. When the lens is shifted upward or downward to the maximum, shift in the left / right direction is not possible.
2% of projected
image width
5% of
projected image
height
2% of projected
image width
Area where shift
is not possible
Projected
image
Shift range
5% of
projected image
height
161
Installation
Area where
shift is not
possible
44% of projected
image height
Installation Manual
Area where lens movement is not possible
With the Standard Zoom Lens, Long Zoom Lens and Ultra Long Zoom Lens, when the
shift exceeds 44% in the upward direction, the amount of available shift in the left / right
directions decreases. When the lens is shifted upward to the maximum (1), the amount of
available shift in the left / right direction is ±2%.
Connecting to AV Equipment
■Connectable Equipment and Input Terminals
HDMI
HDMI IN
terminal
Use this name to select the image input.
The name of the terminal to which to
connect equipment.
Direction of signal and data flow
(Pxxx): indicates the page(s) to refer to.
Analog PC / Component
Digital PC
HDMI
ANALOG PC / COMPONENT IN terminal
DVI-D IN terminal
HDMI IN terminal
Computer (P47, P49)
Computer (P49)
AV equipment (P52)
Digital video camera* (P52)
AV equipment (P53)
AV equipment (P53)
Computer (P51)
* Select playback mode before connecting.
LAN terminal
Service port (not
normally used)
AUDIO IN terminal
Audio signal for each
image input
Network
(P166)
Analog PC /
(P47, P49, Component
P53)
Digital PC
(P50)
162
AUDIO OUT terminal
Amplified speakers
(P51, P55)
Connecting to AV Equipment
Analog PC-1
Component
ANALOG PC-1 / COMPONENT IN terminal
Computer (P48, P49)
Analog PC-2
Digital PC
HDMI
ANALOG PC-2 / DVI-D IN
terminal
HDMI IN terminal
AV equipment (P52)
Computer (P49)
Digital video camera* (P52)
AV equipment (P54)
DVI-I IN terminal can only
be used to connect to a
PC.
Computer (P51)
Installation
Service terminal (not normally used)
LAN terminal
Network
(P166)
AUDIO IN terminal
Remote terminal
Remote control
(RC-RC05)
(P30)
Audio signal for each
image input
Analog
(P48, P49, PC-1, 2 /
Component
P54)
Digital PC
(P50)
163
Installation Manual
* Select playback mode before connecting.
AUDIO OUT terminal
Amplified speakers
(P51, P55)
Connecting to AV Equipment
■Connection Terminal and Connection Cable
Input
signal
Supported
projectors
HDMI
WUX5000
WUX4000
WX6000
SX6000
Digital
PC
Analog
PC-2
Types of connection cables
HDMI cable (not included)
WUX5000
WUX4000
DVI cable (not included)
WX6000
SX6000
WUX5000
WUX4000
WX6000
SX6000
Analog
PC
Analog
PC-1
Input terminal
/
COMPONENT IN
VGA cable (supplied)
BNC cable (not included)
WUX5000
WUX4000
WX6000
SX6000
/
COMPONENT IN
Mini D-sub 15-pin - BNC
terminal converter cable
(not included)
BNC cable
(not included)
VGA-DVI cable (not included)
WX6000
SX6000
Component cable (not included)
Component
WUX5000
WUX4000
WX6000
SX6000
D terminal plug - RCA plug
component conversion cable (not included)
/
COMPONENT IN
RCA plug - RCA plug component cable (not included)
164
Table of Contents
Safety Instructions
Connecting to a
Network
Before Use
Projecting an Image
User’s Manual
Useful Functions Available
During a Presentation
Setting Functions from Menus
Installation
Installation Manual
Connecting to a Network
Maintenance
Appendix
Appendix
Index
165
Preparing the Remote Control
If the projector is connected to a network, projector error notification mails can be
received and the projector can be controlled via a computer. Settings related to the network connection can be made from either the projector side (P172) or computer side
(P177).
Depending on the method of network connection, preparation on the computer side may
be necessary. The following is an explanation of preparation on the computer side.
Connection Methods
Connect the projector to the computer via LAN.
Projector
LAN cable (not included)
(crossover or straight cable)
Hub or router, etc.
• When the [Network function] setting of the projector is set to [Off] (Network Connections
is disabled), switch it to [On] to enable it (P172).
• Referring to page 141, check that the projector IP address does not overlap with other
computers that are on the same LAN. When you set the IP address of the projector, follow the instruction on page 177 on the web screen or refer to page 175.
• When you connect the computer to the network for the first time, it is also necessary to
perform settings on the computer. In this case, consult the network administrator
regarding the necessary settings.
In a network environment where a DHCP server is operating, choose [On] on the projector [DHCP]
screen to enable the DHCP function and connect it (P175).
166
Preparing the Remote Control
Setting an IP Address
Following is an explanation of how to set the PC IP address for each operating system.
■Windows 7
1
2
From the PC [Start] menu, select [Control Panel].
3
4
5
From the menu on the left side of the window, click on [Change adapter settings].
6
Select [Use the following IP address] and set the IP address and subnet mask.
The factory default IP address for the projector is “192.168.254.254”. Set an IP
address which is different from this.
Click on [Network and Internet Connections], then click on [View network status and
tasks].
Right-click [Local Area Connection], and open [Properties].
Select [Internet Protocol Version 4 (TCP/IP)] and click the [Properties] button. Make a
note of the original network settings (IP address, subnet mask, default gateway, etc).
Installation Manual
Example
IP address:192.168.254.1
Subnet mask: 255.255.255.0
When the settings are completed, click the [OK] button and then click the [OK] button
on the [Local Area Connection Properties] window to close it.
167
Connecting to a Network
7
Preparing the Remote Control
■Windows Vista
1
2
3
4
5
From the PC [Start] menu, select [Control Panel].
6
Select [Use the following IP address] and set the IP address and subnet mask.
The factory default IP address for the projector is “192.168.254.254”. Set an IP
address which is different from this.
Click on [View network status and tasks].
From the menu on the left side of the window, click on [Manage network connections].
Right-click [Local Area Connection], and open [Properties].
Select [Internet Protocol Version 4 (TCP/IP)] and click the [Properties] button. Make a
note of the original network settings (IP address, subnet mask, default gateway, etc).
Example
IP address:192.168.254.1
Subnet mask: 255.255.255.0
7
When the settings are completed, click the [OK] button and then click the [OK] button
on the [Local Area Connection Properties] window to close it.
168
Preparing the Remote Control
■Windows XP
1
2
3
4
From the PC [Start] menu, select [Control Panel].
5
Select [Use the following IP address] and set the IP address and subnet mask.
The factory default IP address for the projector is “192.168.254.254”. Set an IP
address which is different from this.
Select [Network and Internet Connections] and open [Network Connections].
Right-click [Local Area Connection], and open [Properties].
Select [Internet Protocol (TCP/IP)] and click the [Properties] button. Make a note of
the original network settings (IP address, subnet mask, default gateway, etc).
Example
IP address:192.168.254.1
Subnet mask: 255.255.255.0
Installation Manual
When the settings are completed, click the [OK] button and then click the [OK] button
on the [Local Area Connection Properties] window to close it.
169
Connecting to a Network
6
Preparing the Remote Control
■Mac OS X
1
2
3
Open the Apple Menu and select [System Preferences].
4
Create a new network environment and set the IP address and subnet mask.
The factory default IP address for the projector is “192.168.254.254”. Set an IP
address which is different from this.
In the System Preferences window, click [Network] to display the Network window.
Select [Built-in Ethernet] and click the [TCP/IP] tab. Make a note of the original network settings (IP address, subnet mask, router, DNS server, etc.).
Example
IP address:192.168.254.1
Subnet mask: 255.255.255.0
5
Click [Apply] to close the network preference window.
■Resetting the IP Address Setting of the Computer
Follow the same procedure as for changing the IP address and reset the values to the
original values based on the notes taken before the change.
170
Network Settings on the Projector
From the projector menus screen, network
settings can be configured in the [Network
Setting] tab. For the menu operations,
refer to page 88.
(The screen is for the WUX5000 /
WUX4000.)
Locking the Network Settings
You can lock / unlock the network settings
so that they cannot be changed and cancel
the lock.
MENU > [Network Setting] > [Network Setting
lock]
Lock
Lock the settings.
After the OK button is pressed to accept
your setting and the MENU button or the
EXIT button (WUX6000 / SX6000) is
pressed to close the window, the lock is
re-engaged. If you change the network
settings, be sure to continue operating
without closing the window.
• [Lock] is the factory default.
• For the default network password, refer to
page 173.
171
Connecting to a Network
Cancels the lock and allows
other network settings to be
changed. The password must
be entered in order to cancel the
lock.
When [Unlock] is selected, the
window shown below appears.
Use the [ ] / [ ] / [ ] / [ ] buttons to enter the 4-digit password.
For the WX6000 / SX6000, numbers can be entered using the
numerical buttons on the remote
control.
Installation Manual
Unlock
Network Settings on the Projector
Turning the Network Function
On / Off
Forcibly canceling the network lock
In the Network Password Input screen, press the
buttons in the following sequence to cancel the
lock: [ ] [OK] [ ] [OK] [ ] [OK]. This will reset
the network password to [ ] [ ] [ ] [ ].
You can turn the projector network function
on or off. Power can be saved by turning
the function [Off].
MENU > [Network Setting] > [Network function]
Off
Disables the network function.
On
Enables the network function.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• [Off] is the factory default.
172
Network Settings on the Projector
Setting a Network Password
You can set whether or not a password is
required in order to change the projector
network settings.
MENU > [Network Setting] > [Network Password setting]
A network password is not used.
On
A network password is used.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• [On] is the factory default.
Register the projector network password.
MENU > [Network Setting] > [Register Network
Password]
When [Register Network Password] is
selected, the window shown below
appears.
Enter a 4 digit password.
For the WUX5000 / WUX4000, the password can be entered using the [ ] / [ ] /
[ ] / [ ] buttons. For the WX6000 /
SX6000, the password can be entered
using a combination of the numerical buttons and the [ ] / [ ] / [ ] / [ ] buttons.
[ ] / [1], [ ] / [2], [ ] / [3], and [ ] / [4]
have the same function.
• The factory default is [ ] [ ] [ ] [ ]
(WUX5000 / WUX4000) or [1] [1] [1] [1]
(WX6000 / SX6000).
173
Connecting to a Network
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
Installation Manual
Off
Registering a Network Password
Network Settings on the Projector
Turning the PJLink Function
On / Off
What is PJLink?
In September 2003, the PJLink Working Group was established under the
Data Projector Committee. During the
first year, this PJLink Working Group
standardized PJLink as a new interface specification for projectors.
PJLink is a unified standard for operation and control of projectors.
It allows centralized control of projectors and operation from a controller for
all projectors regardless of manufacturer.
The objective is for JBMIA to improve
convenience for users and expand
the use of projectors through early
systemization for network monitoring
and control of projectors, which will
become the mainstream in the future.
You can turn the PJLink network function
on or off. When the function is turned on,
control is possible via the LAN using commands that meet PJLink standards.
MENU > [Network Setting] > [PJLink]
Off
Disables the PJLink function.
On
Enables the PJLink function.
Class 1: Standardization of control
and monitoring specifications for
basic projector functions
Basic projector control: Power control,
input selection, etc.
Acquisition of projector information
and status: Power status, input selection status, error status, lamp use
time, etc.
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
• [On] is the factory default.
• This projector conforms to Class 1 as
defined in the PJLink standards of the
JBMIA (Japan Business Machine and
Information System Industries Association). This projector supports all commands that are defined by PJLink Class 1,
and has been verified as conforming to the
PJLink standard Class 1 definition.
• For information about using PJLink, refer to
page 187.
JBMIA: Japan Business Machine and
Information System Industries
Association
The Japan Business Machine
and Information System
Industries Association is an
organization which was
launched in 1960 and
changed its name on April 1,
2002.
PJLink is a registered trademark of JBMIA and
pending trademark in some countries.
174
Network Settings on the Projector
Turning DHCP Function On /
Off
TCP / IP Setting
You can turn the projector DHCP function
on or off.
MENU > [Network Setting] > [TCP/IP setting]
Configure the projector TCP / IP settings.
MENU > [Network Setting] > [DHCP]
Disables the DHCP function. TCP / IP
settings are possible.
On
Enables the DHCP function.
Searches the DHCP server. Because
the IP address is acquired from the
DHCP server, it is not necessary to
enter the TCP / IP settings (IP
address, subnet mask, gateway
address).
• [Off] is the factory default.
• The factory defaults are shown below.
IP address
192.168.254.254
Subnet mask
255.255.255.0
Gateway address 0.0.0.0
• Settings cannot be made when [DHCP]
(P175) is [On].
• If an invalid value is entered, the message
“Invalid entry” appears. If this occurs,
enter a valid value.
175
Connecting to a Network
Press the OK button to accept your setting
and then press the MENU button or EXIT
button (WX6000 / SX6000).
Installation Manual
Off
When [TCP/IP setting] is selected, the window shown below appears. Use the [ ] /
[ ] buttons to select the IP address, then
press the OK button. Next, use the [ ] /
[ ] buttons to select the digit and the [ ] /
[ ] buttons to change the value. For the
WX6000 / SX6000, numbers can be
entered using the numerical buttons on
the remote control. Press the OK button,
then set the subnet mask and gateway
address in the same way. Finally, select
[Enter].
Network Settings on the Projector
Initializing Network Settings
You can initialize the projector network settings.
MENU > [Network Setting] > [Network setting
initialization]
When [Network setting initialization] is
selected, the window shown below
appears. Select [YES] then press the OK
button.
• The following items are initialized.
Network setting screen user name, various
settings including password
Network Password setting
Register Network Password
PJLink
DHCP
IP address
Subnet mask
Gateway address
E-mail sender address
E-mail recipient address
Projector name
Location
176
Configuring the Network From the Computer
■Displaying and Configuring the Network Configuration Screen
The web browser screen shown below is for the WUX4000.
1
2
Turn on the computer and projector.
Launch a web browser, enter “http://(projector IP address)” in the address bar, and
press the Enter key.
The password input screen appears.
The factory default IP address is “192.168.254.254”. If DHCP settings are used, ask the network administrator for the projector IP address. It is possible to check the IP address from
the projector menu.
3
Enter the user name and password on the password input screen, then click OK.
The factory default user name is “root” and the password is “system”.
Installation Manual
The projector web screen appears in the web browser.
Connecting to a Network
177
Configuring the Network From the Computer
The following information is displayed.
Projector name
The name of the projector on the network
Location
The location of projector installation
MAC address
The MAC address of the projector
IP address
The IP address of the projector
Power Status
The power status of the projector
Lamp Time *1
Lamp operating time
Lamp Time Normal Mode *2
Lamp operating time in [Normal] lamp mode
Lamp Time Quiet Mode *2
Lamp operating time in [Quiet] lamp mode
Lamp Time Converted *2
Lamp operating time (converted value)
Filter Time
Air filter operating time
Alert
Error message (if an error has occurred)
Temperature abnormality
Faulty lamp
Faulty lamp cover
Faulty cooling fan
Faulty power supply
Faulty lens connector: Lens connector error
Faulty air filter unit: Air filter error
Unknown error
*1 WUX5000 / WX6000 / SX6000
*2 WUX4000
To operate the projector from the computer, click [Projector control] (P188).
4
To configure, click [Settings].
The settings window appears.
178
Configuring the Network From the Computer
5
Select the function to set from the menu (1), then enter the setting in the displayed
field (2) and click [OK] (3).
(1)
(2)
(3)
6
A confirmation window appears. Check the contents and if they are correct, click
[Apply].
Installation Manual
7
Click [Back to top] to return the web screen to the initial page.
179
Connecting to a Network
The settings are applied to the projector and “Save completed” is displayed.
Configuring the Network From the Computer
■Resetting to Factory Defaults
1
2
Perform steps 1 - 3 on page 177 to display the setting window.
3
A confirmation window appears. Click [OK].
Click [Initialize].
■Setting Errors
When a setting-related error occurs, the error name is displayed on the screen, and a
“!” mark is displayed next to the input field which caused the error.
180
Configuring the Network From the Computer
The error meanings are as shown below.
Error
Meaning
Input error
A setting outside the valid range was set on the
setting screen.
Password setting error
The set password and confirmation password did
not match.
The SMTP server IP address has not been set.
System failed to connect SMTP
server.
Failed to connect to the SMTP server when sending a test mail.
System failed to connect POP3
server.
Failed to connect to the POP3 server attempting to
send a test mail.
System doesn't support this auth
type.
An authentication type was set which is not supported by the server.
System failed to authenticate.
Authentication failed attempting to send a test mail.
The system failed to send the test
mail.
Sending of test mail failed due to a connection failure with the SMTP server or an error which does
not ordinarily occur.
Save Failed
Mismatch in settings occurred when settings were
changed at the same time from multiple computers.
Installation Manual
Invalid SMTP
Connecting to a Network
181
Setting Up the Network
■Setting Basic Information [Network]
From [Network] in the settings window, you can log into the web screen and set basic
network information. For the setting procedure, refer to page 177.
Item
Password
User name
New password
Confirm new password
TCP/IP
DHCP
IP address
Subnet mask
Default gateway
Explanation
Factory default setting
When logging into the web screen, root
enter the user name in 1-byte
alphanumeric characters and
symbols (4 -15 characters).
When logging into the web screen, system
enter the password in 1-byte
alphanumeric characters and
symbols (4 -15 characters).
For confirmation, enter the same
system
password that you entered in [New
password].
Select whether to turn the DHCP
function on or off. If the function is
on, because the IP address is
acquired from the server, it is not
possible to enter the [IP address],
[Subnet mask], and [Default gateway].
Enter the IP address of the projector in 1-byte numbers.
Enter the subnet mask in 1-byte
numbers.
Enter the default gateway IP
address in 1-byte numbers.
OFF
192.168.254.254
255.255.255.0
0.0.0.0
If settings related to TCP / IP were changed, it is necessary to disconnect and reconnect to
the network. If the network subnet mask was changed, select [Subnet mask] in the above
window and set the new subnet mask.
182
Setting Up the Network
■Setting Up Email [Mail]
From [Mail] in the settings window, you can set the items necessary to send error
mails and test mails. For the setting procedure, refer to page 177.
Item
Explanation
Factory default setting
MailUserAccount
Cc:
Enter the CC address for error mails
in 1-byte alphanumeric characters
and symbols (1 - 63 characters).
<Blank>
From:
Enter the sender address for error
mails in 1-byte alphanumeric characters and symbols (1 - 63 characters).
Projector@canon.co.jp
SMTP server IP address
Enter the SMTP server IP address in
1-byte numbers.
0.0.0.0
SMTP server port number
Enter the SMTP server port number
in 1-byte numbers (1 - 65535).
25
SNTP server IP address
Enter the SNTP server IP address in
1-byte numbers.
0.0.0.0
Time zone
Select the time zone where the projector is used.
(GMT) Dublin, Lisbon,
London
Mail resend interval
Enter the interval for resending mail
when an error occurred (units: seconds) within the range of 0 - 59 seconds using 1-byte numbers.
10
Mail resend times
Enter the number of times to resend
mail when an error occurred within
the range of 0 - 255 using 1-byte
numbers.
3
Error report
Select whether to turn the error mail
sending function on or off.
OFF
183
Connecting to a Network
Enter the recipient address for error
mails in 1-byte alphanumeric characters and symbols (1 - 63 characters).
Installation Manual
To:
Setting Up the Network
■Mail Authentication Settings [Mail auth]
From [Mail auth] in the settings window, you can configure the settings for authentication of mail that is sent when an error occurs. For the setting procedure, refer to page
177.
Item
Explanation
Factory default setting
Mail authentication
Select the mail authentication method.
If OFF is selected, the other mail
authentication settings cannot be
changed.
OFF
User name
Enter the user name to use for mail
authentication in 1-byte alphanumeric characters and symbols (1 - 63
characters).
<Blank>
Password
Enter the password for mail authentication in 1-byte alphanumeric characters and symbols (1 - 63 characters).
<Blank>
Confirm password
For confirmation, enter the same
password as you entered in [Password].
<Blank>
POP3 server IP address
Enter the POP3 server IP address in
1-byte numbers.
0.0.0.0
POP3 server port number
Enter the POP3 server port number in
1-byte numbers (1 - 65535).
110
POP before SMTP response time
Enter the wait time from POP3 authentication to SMTP authentication (units:
milliseconds) using 1-byte numbers
(0 - 9999 milliseconds).
300
184
Setting Up the Network
■Sending a Test Mail [Send test mail]
From [Send test mail] in the settings window, you can send a test mail to the mail
address that was set in [Mail]. The settings cannot be changed from this window.
Item
Explanation
The recipient address which was set from [Mail] in the settings window
(P183) is displayed.
Cc:
The CC address which was set from [Mail] in the settings window (P183)
is displayed.
From:
The sender name which was set from [Mail] in the settings window
(P183) is displayed.
Subject:
The predetermined mail title “Canon Projector test” is displayed.
■SNMP Settings [SNMP]
185
Connecting to a Network
From [SNMP] in the settings window, you can configure the settings related to control
of projectors which use SNMP (Simple Network Management Protocol). For the setting procedure, refer to page 177.
Installation Manual
To:
Setting Up the Network
Item
SNMP
Receive community
Password
Confirm password
SNMP trap
Trap IP address
Trap community
Explanation
Select the SNMP function version. If OFF is
selected, the SNMP function will be turned
off and the other settings in this window
cannot be changed.
Enter the community name which will
receive projector information in 1-byte
alphanumeric characters and symbols (1 15 characters).
Enter the community settings password in
1-byte alphanumeric characters and symbols (8 - 15 characters). This is also used
as the password for trapping. It can be set
only when the SNMP version is V3.
For confirmation, enter the same password
as you entered in [Password].
Select the type of error to trap. When any of
the checkboxes is turned on, it becomes
possible to set [Trap IP address] and [Trap
community].
Enter the IP address to send information to
when trap occurs. Enter in 1-byte numbers.
Enter the community name which will send
information when trap occurs. Enter in 1byte alphanumeric characters and symbols
(1 - 15 characters).
Factory default setting
OFF
<Blank>
<Blank>
<Blank>
OFF (no checkmarks)
0.0.0.0
<Blank>
■Setting Projector Information [Projector info.]
From [Projector info.] in the settings window, you can set the names and location
names which are used to identify projectors when multiple projectors are installed on
the network. For the setting procedure, refer to page 177.
Item
Projector name
Location
Explanation
Factory default setting
Enter the projector name in 1-byte alphanu- WUX5000 / WUX4000 /
meric characters and symbols (1 - 63 char- WX6000 / SX6000
acters).
Enter the projector installation location in 1- <Blank>
byte alphanumeric characters and symbols
(0 - 63 characters).
186
Setting Up the Network
■Setting PJLink [PJLink]
From [PJLink] in the setting window, you can set the PJLink functions which are the
standard for projector management on a network. For the setting procedure, refer to
page 177. For information about PJLink, refer to page 174.
Item
Explanation
Factory default
setting
ON
PJLink authentication
Select whether to turn the PJLink
authentication function on or off. If
OFF is selected, [Password] and
[Confirm password] cannot be
changed.
ON
Password
Enter the PJLink authentication
password in 1-byte alphanumeric
characters (1 - 32 characters).
system
Confirm password
For confirmation, enter the same
password that you entered in
[Password].
system
187
Connecting to a Network
Turn the PJLink function on or off. If
OFF is selected, the PJLink function will be turned off and the other
settings in this window cannot be
changed.
Installation Manual
PJLink
Controlling the Projector from a Computer
When the projector is connected to a network, it is possible to control the projector from a
computer via the network.
1
2
Turn on the computer and projector.
3
Enter the user name and password on the password input screen, then click OK.
The factory default user name is “root” and the password is “system”.
4
The projector web screen appears in the web browser. Click [Projector control].
Launch a web browser, enter “http://(projector IP address)” in the address bar, and
press the Enter key.
The password input screen appears.
The factory default IP address is “192.168.254.254”. It is possible to check the IP
address from the projector menu.
188
Controlling the Projector from a Computer
5
The projector control screen appears. The projector can be controlled from this
screen.
Item
The name of the connected projector is displayed. (P186)
IP address
The IP address of the connected projector is displayed. (P182)
Refresh
Refreshes the displayed contents with the most recent information.
Power
Turns projector power on or off.
Input
Select an input signal and click [Apply] to change to that input
signal. (P59)
Aspect
Select an aspect and click [Apply] to change to that aspect. (P69)
Image mode
Select an image mode and click [Apply] to change to that image
mode. (P78)
Switches the blank setting on or off. (P82)
Switches the mute setting on or off. (P83)
Auto PC
Performs Auto PC. (P62)
Information
The control results and control error information are displayed at
the top of the screen.
When the operations are finished, click [Back to top] to return the initial web screen.
189
Connecting to a Network
Blank
Mute
Installation Manual
6
Explanation
Projector name
Error Mail
The messages shown in the following error list are sent when an error occurs in the projector.
Error list
Errors related to
temperature
Error
name
Text
Errors related to
the lamp
Error
name
Text
Errors related to
the lamp cover
Error
name
Text
Errors related to
the cooling fan
Error
name
Text
Errors related to
the power supply
Error
name
Text
Errors related to
the lens connector
Error
name
Errors related to
the air filter
Error
name
Text
Text
Other types of
errors
Error
name
Text
Temperature abnormality
The temperature inside the projector is too high for some reason or the
outside air temperature is higher than the specified one.
If the problem is inside the projector, check whether the projector is
installed and operated normally, turn off the projector to cool its inside,
and retry projection. If the same warning occurs again, the projector
may be defective. Contact your dealer.
Faulty lamp
The lamp has burnt out. Replace the lamp with a new one. If the same
warning occurs again, the lamp drive circuit may be defective. Contact your dealer.
Faulty lamp cover
The lamp cover is open. Check whether the lamp cover is installed
properly. If it is installed properly, the lamp cover detection switch may
be defective. Contact your dealer.
Faulty cooling fan
The cooling fan or another component may be defective. Contact your
dealer.
Faulty power supply
The voltage of part of the power supply is abnormally high or any
other problem has occurred in the power supply. Contact your dealer.
Faulty lens connector
The lens cable is not connected to the lens unit. Check whether the
lens cable is connected to the lens unit properly.
If it is connected properly, the lens connector or cable may be defective. Contact your dealer.
Faulty air filter unit
The air filter unit is not installed properly.
Check whether the air filter unit is installed properly.
If it is installed properly, the air filter unit detection switch may be
defective. Contact your dealer.
Unknown Error
Code in hexadecimal numbers*
* For details, contact the Canon Customer Support Center.
190
Table of Contents
Safety Instructions
Maintenance
Before Use
Projecting an Image
User’s Manual
Useful Functions Available
During a Presentation
Setting Functions from Menus
Installation
Installation Manual
Connecting to a Network
Maintenance
Appendix
Appendix
Index
191
Cleaning the Projector
Clean the projector frequently to prevent dust from settling on the surface.
A dirty lens may ruin the quality of the projected image.
When cleaning the projector, make sure to turn off the projector,
wait until the cooling fan stops, disconnect the power plug from the
electrical outlet, and let the projector stand for at least 1 hour. Otherwise, you may get burned because the main unit is very hot
immediately after the projector is turned off.
Wipe the projector’s main unit softly with a soft cloth.
If the projector is heavily soiled, soak the cloth in water with a small amount of detergent
in it, squeeze the cloth thoroughly, and then wipe the projector with it. After cleaning, wipe
the projector with a dry cloth.
• Never use volatile cleaning liquid or benzine, as these may damage the finish of the projector.
• When using a chemical dust cloth, make sure to read the instructions thoroughly.
• When cleaning the projector’s lens, use a commonly available air blower or lens cleaning
paper. The lens surface is easily damaged, so do not use a hard cloth or tissues.
192
Cleaning and Replacing the Air Filter
Replacing the Air Filter
Follow the procedure below when replacing the air filter.
1
2
Turn off the projector power and remove the power plug.
Hook your finger onto the handle of the
air filter on the side of the projector, and
pull the air filter out to remove it.
Air filter
Remove the filter from the air filter
frame. First disengage the tab on the
inside, then remove the entire air filter
from the frame.
4
Install a new air filter into the frame.
First insert the air filter tab into the
groove on the handle side of the frame,
then press the air filter into the frame.
Installation Manual
3
Maintenance
193
Cleaning and Replacing the Air Filter
5
Securely insert the air filter all the way
into the projector.
•
•
•
•
•
Handle the air filter carefully. If damaged, the air filter will not work properly.
When the lamp is replaced, it is recommend that you also replace the air filter.
Contact the Canon Customer Support Center for further information.
Replacement air filter part No.: RS-FL01
This can also be purchased from the Canon home page
(http://store.canon.jp/user/ListProducts/list?svid=2&sc=LMPPR&jsp=/jsp/search/
search_item_acc.jsp).
Cleaning the Air Filter
The air filter protects the lens and mirror inside the projector from dust and dirt. Should
the air filter become clogged with dust, the projector may be damaged since it will block
the air flow into the projector and raise the internal temperature of the projector. The following screen is displayed when turning on the projector if the air filter needs to be
cleaned (after approx. 300 hours). Clean the air filter if it is displayed.
• Only the [ ], [ ], OK and POWER buttons are
available while this screen is displayed. (When you
press the POWER button, the message “Push
POWER button again to turn off power” appears.)
• When this screen has disappeared after being displayed for 10 seconds, all buttons become operable.
• Turn the power of the projector off and pull out the power plug.
• Hook your finger into the air filter handle on the side of the projector, and remove the air
filter. Then use a vacuum cleaner to remove the dust.
• If the filter replacement screen is displayed when turning on the projector after cleaning
the air filter, select [Yes] and press OK. The filter replacement screen will disappear.
• This screen is not displayed when [Filter warning display] is set to [Off]. (WX6000 /
SX6000) (P137)
194
Replacing the Lamp
When the usage time of the lamp exceeds a certain amount of time, the following message (two types) is displayed for 10 seconds every time the projector is turned on.
2,700 hours to less than 3,000 hours
Prepare a new lamp when this screen is displayed.
• Only the [ ], [ ], OK and POWER buttons are available while this screen is displayed.
• When you press the POWER button, “Push POWER button again to turn off power.”
message appears.
• After this screen has been displayed for 10 seconds and disappeared, all buttons
become operable.
• This message will not be displayed again if you select [Cancel] in response to the message “Do you want to display this message again?”.
3,000 hours or more
Maintenance
195
Installation Manual
If this screen is displayed, replace the lamp by referring to the procedure on page 196.
• Only the POWER button is available while this screen is displayed.
• When you press the POWER button, the “Push POWER button again to turn off power.”
message appears.
• When this screen has disappeared after being displayed for 10 seconds, all buttons
become operable.
• You can check the usage time of the lamp in [Lamp counter] in the [System settings]
menu. (P135)
• This screen is not displayed when [Lamp warning display] is set to [Off]. (WX6000 /
SX6000) (P135)
Replacing the Lamp
Replacement Lamp
This projector uses the following lamps.
Lamp part No.: RS-LP06 (WUX4000)
RS-LP07 (WUX5000 / WX6000 / SX6000)
Contact the Canon Customer Support Center when purchasing a replacement lamp.
When replacing the lamp, turn off the projector, wait until the cooling fan stops, disconnect the power plug from the electrical outlet,
and let the projector stand for at least 1 hour. Otherwise, you may
get burned because the main unit is very hot immediately after the
projector is turned off.
• Be sure to use the specified lamp.
• Contact the Canon Customer Support Center or access to the
Canon home page.
• Do not touch the inner glass surface when you replace the lamp.
Doing so may cause deterioration to the projector’s performance.
• Be sure to handle the lamp carefully and correctly since it may
break during use if it has been scratched or subjected to impact.
If the lamp breaks, contact the Canon Customer Support Center
or follow the instructions on page 21 and page 22.
• When replacing the lamp, do not remove any screws other than
those specified.
Replacing the Lamp
1
2
Turn off the projector power and remove the power plug.
Loosen one screw and open the lamp cover in the direction of the arrow.
The lamp cover screw is attached to the lamp cover and designed to prevent it from
falling off.
Screw
196
Replacing the Lamp
3
Loosen the 3 screws on the inside of the lamp unit, then slowly pull out the lamp unit in
the direction of the arrow.
Even when the screws are loosened, they will not fall off the lamp unit.
4
5
6
Fully insert a new lamp unit and secure it with the 3 screws.
Close the lamp cover and tighten the screws.
Turn on the power. Bring up the menu and select [System settings] - [Other settings] [Lamp counter].
Installation Manual
Maintenance
(The screen is for the WUX5000 / WUX4000.)
197
Replacing the Lamp
7
Select [Reset] - [OK] to reset the lamp counter.
(The screen is for the WUX5000 / WUX4000.)
• It is recommended that you also replace the air filter when you replace the lamp.
• Contact the Canon Customer Support Center for further information.
• Replacement air filter product number: RS-FL01
198
MULTIMEDIA PROJECTOR
Appendix
199
200
Table of Contents
Safety Instructions
Appendix
Before Use
Projecting an Image
User’s Manual
Useful Functions Available
During a Presentation
Setting Functions from Menus
Installation
Installation Manual
Connecting to a Network
Maintenance
Appendix
Appendix
Index
201
Troubleshooting
LED Indicator Meanings
When there is a problem with the projector, the LED indicator on the side of the projector
illuminates or flashes continuously after the projector is turned off.
• Wait until the cooling fan stops and disconnect the power plug from the electrical outlet
before dealing with the problem.
LED indicator
status
Meaning
Countermeasure
WARNING and
TEMP are lit.
Temperature
abnormality
The temperature inside the projector is too high for some
reason or the outside air temperature is higher than the operating range. If the problem is inside the projector, check
whether the projector is installed and operating normally,
unplug the projector from the power outlet to cool down the
projector interior and then restart projection. If the air intake
or exhaust vent is blocked, remove the obstacle. If the same
warning occurs again, there may be a malfunction in the
projector. Contact the Canon Customer Support Center.
WARNING and
LAMP are lit.
Faulty lamp
The lamp does not illuminate. Turn the power off and then
back on and check whether or not the lamp illuminates.
Also, check whether the air intake or exhaust vent is
blocked, and whether the air filter is clogged with dust. The
warning may indicate if the air flow in and out of the projector
is blocked, or if the internal temperature of the projector
rises. If the air filter is clogged, clean or replace the air filter.
(P193, P194) If the lamp does not illuminate, replace it. If the
same warning occurs again, there may be a malfunction in
the lamp drive circuit. Contact the Canon Customer Support
Center.
WARNING
flashes 3
times, LAMP is
lit.
Faulty lamp
cover
The lamp cover is open. Unplug the projector from the electrical outlet, then install the lamp cover correctly and turn on
the projector again. If the lamp cover has been installed
properly, there may be a malfunction in the lamp cover
detection switch. Contact the Canon Customer Support
Center.
WARNING
(only) flashes 4
times repeatedly.
Faulty cooling fan
There may be a malfunction in the cooling fan or another
component. Unplug the projector from the electrical outlet,
then plug it into the outlet and turn on the projector again.
Contact the Canon Customer Support Center if the same
warning occurs again.
WARNING
(only) flashes 5
times repeatedly.
Faulty power
supply
Abnormal voltage is applied to some parts in the power supply or another failure may have occurred. Unplug the projector from the electrical outlet, then plug it back into the outlet
and turn on the projector again. Contact the Canon Customer Support Center if the same warning occurs again.
202
Troubleshooting
LED indicator
status
Meaning
Countermeasure
WARNING
(only) flashes 6
times repeatedly.
Faulty lens
connector
Disconnect the lens connector which joins the lens unit and
projector. Contact the Canon Customer Support Center.
WARNING
(only) flashes 3
times repeatedly.
Filter error
The air filter is not installed. Check whether or not the air filter
is installed correctly. Contact the Canon Customer Support
Center if the same warning occurs again.
Symptoms and Solutions
■You Cannot Turn on the Projector
Cause
Countermeasure
Check whether the power cord is connected correctly.
(P56)
The power cord has just been
connected.
You cannot turn on the projector until the [STAND BY] indicator turns red after connecting the power plug. (P56)
The lamp cover is open.
Unplug the projector from the power outlet, then install the
lamp cover correctly and turn on the projector again.
The safety device is activated
because the air intake or the
exhaust vent is blocked and the
internal temperature of the projector has increased.
When the safety device is active, the [STAND BY] indicator
does not turn on when you connect the power cord. You
cannot disable this safety device. Remove any obstacle
that is blocking the air intake or exhaust vent and contact
the Canon Customer Support Center.
The lens connector is not connected correctly.
The lens connector that connects the lens unit with the main
unit of the projector is disconnected. Contact the Canon
Customer Services Center.
The air filter is not installed correctly.
Check whether the air filter is installed correctly. (P193)
Key lock is enabled.
Check that Key lock (P123) is not enabled for the projector
or the remote control.
Appendix
The power cord is not connected
correctly.
■You Cannot Project an Image from the Projector
Countermeasure
Check whether the projector is connected to the computer
or AV equipment correctly. (P52, P59)
20 seconds have not elapsed
since the projector was turned on.
When the projector is turned on, the opening window is displayed for approximately 20 seconds. To project an image
immediately, press the OK button on the remote control or
side control. (P56)
No image is sent from the AV
equipment.
Check whether an image is played on the connected video
camcorder, DVD, etc.
203
Other Information
Cause
A cable is not connected correctly.
Troubleshooting
Cause
Countermeasure
Connection with the input terminal
has not been performed correctly.
Check whether the AV equipment is connected to the projector input terminal correctly. (P47)
No input signal type has been
selected for the connected AV
equipment.
Check that the same input signal has been correctly
selected for the connected AV equipment from the [INPUT]
menu. (P60)
The input signal type is incorrect.
Check whether the selected input signal type is correct.
(P94, P218)
The BLANK function has been
selected.
Press the BLANK button on the remote control. (P82)
No image is projected due to a
problem with the computer.
Turn first the projector and then the computer off and then
back on again.
The external monitor output is not
set on the notebook computer
correctly.
Turn on the external monitor output on the notebook computer. To turn on the external monitor output, press the
[LCD] or [VGA] function key or a key with an icon for the
external monitor, while holding down the [Fn] key on the
keyboard of the notebook computer. With Windows 7, you
can turn on image output by holding down the Windows
logo key and pressing the [P] key. (P58)
The combination of keys used to perform this operation varies depending on the model of notebook computer. For
more detailed information, refer to the manual that came
with your computer.
The displayed image is not the
same as that displayed on the
computer.
Check whether the dual screen (multi-display) mode is
selected on the computer. If the dual screen mode has
been selected, change it to the simultaneous display mode
on the computer.
The output setting method varies among computer manufacturers. For more detailed information, refer to the manual
that came with your computer.
■There is no Sound
Cause
Countermeasure
The audio cable is not connected
correctly.
Check the audio cable connection. (P162)
The MUTE function is enabled.
Press the MUTE button on the remote control. (P83)
The volume level is adjusted to
the minimum.
Press the VOL button on the remote control or the VOL+
button on the side control to adjust the volume level. (P83)
An audio cable with a built-in
resistor is used.
Use an audio cable without a built-in resistor.
Audio in terminal select is [Off]
(WX6000 / SX6000).
Change the Audio In terminal to the appropriate setting.
(P139)
204
Troubleshooting
■The Projected Image Is Blurred
Cause
Countermeasure
The image is out of focus.
Adjust the focus. (P73)
The distance to the screen is too
short.
Check whether the distance to the screen is appropriate. If
the distance is shorter than approximately 1.3 m (4.3'), the
projector cannot focus on the screen. (P156)
The projector is not placed
straight in front of the screen.
Check whether the projector is placed obliquely to the
screen. A slight error in the projection angle can be corrected through the keystone adjustment function. (P76)
The projector has been moved to
a place where the temperature
varies a lot.
When the projector is moved from a location where the temperature is low to a location where the temperature is high,
condensation may form on the lens. The condensation will
evaporate after a period of time and the projector will be
able to project a normal image.
The lens is stained.
Clean the lens. (P192)
The tracking is bad.
Adjust the tracking with the [AUTO PC] or [Tracking] function. (P62, P96)
■You Cannot Project an Image Appropriately
Cause
Countermeasure
The projected image is inverted in
the vertical or horizontal direction.
The ceiling mounted / rear projection setting is incorrect.
Check the [Image flip H/V] setting in the [Display settings]
menu. (P104)
The dot clock of the input signal is
higher than 162 MHz with a BNC
cable.
Set the signal dot clock to 162 MHz or less on your computer.
A VGA cable is used in which
some pins are not connected.
Use a VGA cable in which all pins are connected.
Cause
Countermeasure
Check whether the air intake or exhaust vent is blocked. If
the air intake or exhaust vent is blocked, the temperature
inside the projector will increase and the power is automatically turned off to protect the projector. (The [WARNING]
indicator and [TEMP] indicator are lit.) Wait until the projector temperature drops, then make sure that the intake and
exhaust vents are not blocked and turn on the projector.
(P32, P56)
The air filter is dirty.
Check whether the air filter is clogged with dust.
If the air filter is clogged, clean or replace the air filter.
(P193)
205
Other Information
The air intake or exhaust vent is
blocked.
Appendix
■The Projector Power Turns Off
Troubleshooting
Cause
Countermeasure
The lamp has broken (or there is a
lamp malfunction).
Check whether the lamp has broken.
If the lamp has broken, follow the instructions on page 21. If
the lamp has not broken, there may be a malfunction with
the lamp. Check the lamp by replacing it with a spare lamp
if you have one. (P22, P195, P196)
The operating temperature is
inappropriate.
Check whether the operating temperature is between 5°C
and 35°C. (P24)
If you use the projector at 2300 m or higher above sea level,
contact the Canon Customer Support Center.
■You Cannot Operate the Remote Control
Cause
Countermeasure
Batteries are not installed properly or they have run out.
Check whether batteries are installed correctly. If batteries
are installed correctly, replace them with new batteries.
(P27)
You are operating the remote control from the outside of the remote
control operating range.
Check whether you are operating the remote control within
the remote control operating range of the main unit of the
projector. (P29)
There is an obstacle between the
projector and the remote control.
Remove the obstacle between the infrared remote receiver
of the main unit of the projector and the remote control or
point the remote control in an obstacle-free path.
You are operating the remote control in an unsuitable operating
environment.
Check whether the infrared remote receiver of the main unit
of the projector is exposed to direct sunlight or strong light
of lighting apparatus. (P29)
The channel setting of the remote
control does not match the setting
of the projector.
Check whether the channel setting of the remote control
has been changed. You can check the [Remote control]
setting in the [System settings] menu. (P124)
The key lock function is preventing operation of the remote control.
Check whether [Key lock] is enabled to disable the remote
control operation.
In the System settings menu, set [Key lock] to [Off]. (P123)
When using infrared operation,
the cable is connected to the terminal for the wired remote control
of the projector or remote control
(WX6000 / SX6000).
Pull out the cable that is connected to the terminal for the
wired remote control of the projector or remote control.
(P30)
When using with the cable connected, the cable may not be
connected to the terminal for the
wired remote control of the projector or remote control (WX6000 /
SX6000).
Check whether the cable is connected to the terminal for
the wired remote control of the projector and remote control. Also check that the cable is not broken. (P30)
If the above causes cannot be identified, the projector may be damaged. Contact the
Canon Customer Support Center as soon as possible.
206
Relationship between Aspect and Screen Aspect
This section describes the relationship between screen aspect (P63) and aspect (P69).
To project an image on the whole screen, select the most appropriate screen aspect ratio
and aspect according to the aspect ratio of the screen and input signal type.
• If an image from image software with an aspect ratio of 16:9 is not projected correctly, select [16:9]
as the screen aspect.
• For a 16:9 image with black borders at the top and bottom, such as a terrestrial broadcast movie,
you can project the 16:9 image area so that it is projected on the entire screen by selecting [Zoom]
in [Aspect].
[Zoom] is available when [16:10], [16:9] or [16:9 D. image shift] is selected for the screen aspect
and [HDMI (480p, 576p)] or [Component (480p, 480i, 576p, 576i)] is selected for the input signal.
• To perform keystone adjustment (P76), select [16:10], [4:3] or [16:9] for [Screen aspect].
WUX5000 / WUX4000
■When the image is projected on a 16:10 screen
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(16:10)
1920 x 1200
1440 x 900
1280 x 800
(16:9)
1920 x 1080
1280 x 720
Screen image
[Full]
[Auto]
[Full]
[16:10]
[Full]
Appendix
(4:3)
1600 x 1200
1400 x 1050
640 x 480
Other Information
207
Relationship between Aspect and Screen Aspect
■When the image is projected on a 16:9 screen
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(16:10)
1920 x 1200
1440 x 900
1280 x 800
(16:9)
1920 x 1080
1280 x 720
Screen image
[16:9]
[16:9]
[Auto]
[16:9]
[16:9 D. image shift]
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[16:9]
■When the image is projected on a 4:3 screen
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(16:10)
1920 x 1200
1440 x 900
1280 x 800
(16:9)
1920 x 1080
1280 x 720
[4:3]
[4:3]
[4:3 D. image shift]
[4:3]
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[4:3]
[Auto]
208
Screen image
Relationship between Aspect and Screen Aspect
■When projecting on a 16:10 screen in the aspect ratio of the connected
device
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(16:10)
1920 x 1200
1440 x 900
1280 x 800
(16:9)
1920 x 1080
1280 x 720
Screen image
[Full]
[Auto]
[16:9]
[Auto]
[16:10]
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[4:3]
[Auto]
■When projecting on a 16:9 screen in the aspect ratio of the connected
device
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(16:10)
1920 x 1200
1440 x 900
1280 x 800
(16:9)
1920 x 1080
1280 x 720
Screen image
[Auto]
[16:9]
[Auto]
[16:9]
[16:9 D. image shift]
[4:3]
[Auto]
Appendix
(4:3)
1600 x 1200
1400 x 1050
640 x 480
Other Information
209
Relationship between Aspect and Screen Aspect
■When projecting on a 4:3 screen in the aspect ratio of the connected
device
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(16:10)
1920 x 1200
1440 x 900
1280 x 800
(16:9)
1920 x 1080
1280 x 720
Screen image
[Auto]
[16:9]
[Auto]
[4:3]
[4:3 D. image shift]
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[4:3]
[Auto]
WX6000
■When the image is projected on a 16:10 screen
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(16:10)
1920 x 1200
1440 x 900
1280 x 800
(16:9)
1920 x 1080
1280 x 720
[16:10]
[Auto]
[16:10]
[16:10]
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[16:10]
210
Screen image
Relationship between Aspect and Screen Aspect
■When the image is projected on a 16:9 screen
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(16:10)
1920 x 1200
1440 x 900
1280 x 800
(16:9)
1920 x 1080
1280 x 720
Screen image
[16:9]
[16:9]
[Auto]
[16:9]
[16:9 D. image shift]
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[16:9]
■When the image is projected on a 4:3 screen
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(16:10)
1920 x 1200
1440 x 900
1280 x 800
(16:9)
1920 x 1080
1280 x 720
Screen image
[4:3]
[4:3]
[4:3 D. image shift]
[4:3]
[4:3]
[Auto]
Appendix
(4:3)
1600 x 1200
1400 x 1050
640 x 480
Other Information
211
Relationship between Aspect and Screen Aspect
■When projecting on a 16:10 screen in the aspect ratio of the connected
device
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(16:10)
1920 x 1200
1440 x 900
1280 x 800
(16:9)
1920 x 1080
1280 x 720
Screen image
[16:10]
[Auto]
[16:9]
[Auto]
[16:10]
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[4:3]
[Auto]
■When projecting on a 16:9 screen in the aspect ratio of the connected
device
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(16:10)
1920 x 1200
1440 x 900
1280 x 800
(16:9)
1920 x 1080
1280 x 720
[16:10]
[Auto]
[16:9]
[16:9 D. image shift]
[16:9]
[Auto]
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[4:3]
[Auto]
212
Screen image
Relationship between Aspect and Screen Aspect
■When projecting on a 4:3 screen in the aspect ratio of the connected
device
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(16:10)
1920 x 1200
1440 x 900
1280 x 800
(16:9)
1920 x 1080
1280 x 720
Screen image
[16:10]
[Auto]
[16:9]
[Auto]
[4:3]
[4:3 D. image shift]
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[4:3]
[Auto]
SX6000
■When the image is projected on a 4:3 screen
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[4:3]
[Auto]
[4:3]
[4:3]
(16:9)
1920 x 1080
1280 x 720
[4:3]
Appendix
(16:10)
1920 x 1200
1440 x 900
1280 x 800
Screen image
Other Information
213
Relationship between Aspect and Screen Aspect
■When the image is projected on a 16:10 screen
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(4:3)
1600 x 1200
1400 x 1050
640 x 480
(16:10)
1920 x 1200
1440 x 900
1280 x 800
Screen image
[16:10]
[16:10]
[16:10 D. image shift]
[16:10]
[Auto]
(16:9)
1920 x 1080
1280 x 720
[16:10]
■When the image is projected on a 16:9 screen
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(4:3)
1600 x 1200
1400 x 1050
640 x 480
(16:10)
1920 x 1200
1440 x 900
1280 x 800
[16:9]
[16:9]
[16:9 D. image shift]
[16:9]
(16:9)
1920 x 1080
1280 x 720
[16:9]
[Auto]
214
Screen image
Relationship between Aspect and Screen Aspect
■When projecting on a 4:3 screen in the aspect ratio of the connected
device
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(4:3)
1600 x 1200
1400 x 1050
640 x 480
(16:10)
1920 x 1200
1440 x 900
1280 x 800
Screen image
[4:3]
[Auto]
[16:10]
[Auto]
[4:3]
(16:9)
1920 x 1080
1280 x 720
[10:9]
[Auto]
■When projecting on a 16:10 screen in the aspect ratio of the connected
device
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[4:3]
[Auto]
[16:10]
[16:10 D. image shift]
[16:10]
[Auto]
(16:9)
1920 x 1080
1280 x 720
[10:9]
[Auto]
Appendix
(16:10)
1920 x 1200
1440 x 900
1280 x 800
Screen image
Other Information
215
Relationship between Aspect and Screen Aspect
■When projecting on a 16:9 screen in the aspect ratio of the connected
device
Aspect ratio of
connected device
Screen aspect setting
(P63)
Aspect setting (P69)
(4:3)
1600 x 1200
1400 x 1050
640 x 480
(16:10)
1920 x 1200
1440 x 900
1280 x 800
[4:3]
[Auto]
[16:9]
[16:9 D. image shift]
[16:10]
[Auto]
(16:9)
1920 x 1080
1280 x 720
[16:9]
[Auto]
216
Screen image
Displayed Test Patterns
If using WX6000 / SX6000
The test pattern can be displayed by pressing the [TEST PATTERN] button. Use this when
there is no image signal, etc.
While the test pattern is displayed, you can use the [ ] / [ ] buttons to change to a different test pattern. Also, if there is an option pattern available, you can use the [ ] / [ ] buttons to switch pattern.
The following test patterns can be displayed.
Option pattern
[ ] / [ ] switch pattern
([ ] / [ ] switch pattern)
Color bar
White / red /
green / blue
(Raster 100%)
White / red /
green / blue
(Raster 50%)
Other Information
217
Appendix
The following functions in the [Image
adjustment] tab are not applied to the
test pattern.
• Brightness adjustment function
(P111)
• Contrast adjustment function (P112)
• Sharpness adjustment function
(P113)
• Color level adjustment function
(P114)
• Color balance adjustment function
(P114)
Supported Signal Types
This projector supports the following signal types.
If your computer or AV equipment is compatible with any one of these signal types, the
projector’s Auto PC function selects the input signal type to project an image appropriately.
ANALOG RGB
HDMI
Horizontal freVertical freConnecting to a computer
Resolution (dots) Signal type
640 x 480
720 x 480
720 x 576
800 x 600
848 x 480
1024 x 768
VGA
SVGA
XGA
1280 x 720
-
1280 x 768
WXGA
1280 x 800
1280 x 960
1280 x 1024
1360 x 768
1366 x 768
MAC
SXGA
-
1400 x 1050
SXGA+
1440 x 900
WXGA+
1600 x 1200
UXGA
1680 x 1050
WSXGA+
1920 x 1080
-
1920 x 1200
(WUX5000 / WUX4000)
WUXGA
quency (kHz)
31.469
31.469
31.250
37.879
31.020
48.363
37.500
45.000
47.776
47.396
49.702
49.306
60.000
63.981
47.712
47.712
64.744
65.317
55.935
55.469
75.000
64.674
65.290
56.250
67.500
quency (Hz)
59.940
59.940
50.000
60.317
60.000
60.004
50.000
60.000
59.870
59.995
59.810
59.910
60.000
60.020
60.015
59.790
59.948
59.978
59.887
59.901
60.000
59.883
59.954
50.000
60.000
74.038
59.950
Resolution
(dots)
640 x 480
800 x 600
1024 x 768
1280 x 800
640 x 480
720 x 480
720 x 576
800 x 600
1024 x 768
1280 x 720
1280 x 800
1280 x 1024
1400 x 1050
1440 x 900
1600 x 1200
1680 x 1050
1920 x 1080
1920 x 1200
D-WUXGA
(WUX5000 / WUX4000)
74.038
WXGA
1280 x 1024
SXGA
1400 x 1050
SXGA+
1440 x 900
WXGA+
1600 x 1200
UXGA
1680 x 1050
WSXGA+
1920 x 1200
(WUX5000 /
WUX4000)
WUXGA
Signal type
480p
576p
720p
1080i
Horizontal frequency (kHz)
D-VGA
31.469
31.469
31.250
D-SVGA
37.879
D-XGA
48.363
37.500
45.000
49.702
D-WXGA
49.306
D-SXGA
63.981
64.744
D-SXGA+
65.317
55.935
D-WXGA+
55.469
D-UXGA
75.000
64.674
DWSXGA+
65.290
56.250
67.500
VGA
SVGA
XGA
Horizontal frequency (kHz)
31.469
37.879
48.363
49.702
49.306
63.981
64.744
65.317
55.935
55.469
75.000
64.674
65.290
Vertical frequency (Hz)
59.940
60.317
60.004
59.810
59.910
60.020
59.948
59.978
59.887
59.901
60.000
59.883
59.954
74.038
59.950
Connecting with AV equipment
DVI
Resolution (dots) Signal type
Signal type
1080p
Vertical frequency (Hz)
59.940
59.940
50.000
60.317
60.004
50.000
60.000
59.810
59.910
60.020
59.948
59.978
59.887
59.901
60.000
59.883
59.954
50.000
60.000
Horizontal frequency
(kHz)
31.469
31.250
37.500
45.000
28.125
33.750
56.250
67.500
Vertical frequency
(Hz)
59.940
50.000
50.000
60.000
50.000
60.000
50.000
60.000
COMPONENT
Signal type
480i
480p
576i
576p
720p
720p
1080i
1080i
1080p
1080p
59.950
* The specifications in the table above are subject to
change without notice.
* This projector does not support any computer output
signal with a dot clock of higher than 162 MHz.
* Use a VGA cable in which all pins are connected. If the
cable is a type in which all pins are not connected, the
image may not be correctly displayed.
218
Horizontal frequency
(kHz)
15.734
31.469
15.625
31.250
37.500
45.000
28.125
33.750
56.250
67.500
Vertical frequency (Hz)
59.940
59.940
50.000
50.000
50.000
60.000
50.000
60.000
50.000
60.000
Product Specifications
■Projector
Model name
Display system
Projection Display device
lens(*1)
Optical system
WUX5000
WUX4000
RGB liquid crystal system
Color separation by dichroic mirror / polarizing beam splitter and color composition by prism
Type
Reflective liquid crystal panel
Size / Aspect ratio
0.71'' X3 / 16:10
Drive system
Active matrix system
Number dots / Total number dots
2,304,000 (1920 x 1200) x 3 panels / 6,912,000
Zoom ratio / Focal length / F value
1.5x / f = 23.0 - 34.5 mm / F1.89 - F2.65
Zooming / Focusing system
Electric / Electric
Lens shift
V: -15% - +55%, H: ±10%
310-NSHA 300 / 264 W
(lamp mode Normal / Quiet)
Image size (projection distance) (*1)
Size 40 to 600 (1.3 m / 4.6' to 29.0 m / 95.1')
Number of colors
16,770,000 colors (full color)
Brightness (*1)
5,000 lumen
4,000 lumen (*2)
Contrast ratio
1000:1 (Full white: Full black, during presentation)
Ratio of brightness at periphery to center (*1)
88%
Speaker
5W monaural x 1
Maximum input resolution
1920 x 1200 dots
WUXGA / UXGA / WSXGA+ / SXGA+ / WXGA+ / SXGA / WXGA / XGA /
Analog PC input
SVGA / VGA
(Scan frequency: Horizontal 15 - 75 kHz, Vertical 50 - 85 Hz)
WUXGA
/
UXGA
/
WSXGA+
/
SXGA+ / WXGA+ / SXGA / WXGA / XGA /
Digital PC input
SVGA / VGA
Component input
1080p, 1080i, 720p, 576i, 576p, 480i, 480p
HDMI input
1080p, 1080i, 720p, 576p, 480p
DVI-D IN terminal
Digital PC (24-pin DVI connector)
HDMI IN terminal
HDMI (deep color)
ANALOG PC / COMPONENT IN terminal
Analog PC, Component (mini D-sub 15-pin)
CONTROL terminal
RS-232C (D-sub 9-pin)
AUDIO IN Terminal
Audio signal (3.5Ø stereo mini jack x 2)
AUDIO OUT Terminal
Audio signal (3.5Ø stereo mini jack)
LAN terminal
Network connection (RJ-45)
Digital PC
TMDS (Transition Minimized Differential Signaling)
0.7Vp-p, positive polarity, impedance = 75Ω
Horizontal / vertical synchronization: TTL level, negative or positive polarity
Analog PC
Composite synchronization in G signal: 0.3Vp-p, negative polarity, impedance = 75Ω
COMPONENT: Separate Y Cb/Pb Cr/Pr signal
Y:
1Vp-p,
negative
synchronization,
impedance = 75Ω
Component video
Cb/Pb: 0.7Vp-p, impedance = 75Ω
Cr/Pr: 0.7Vp-p, impedance = 75Ω
Audio
Impedance = 47kΩ or more
39 / 36dB
Noise
40 dB
(lamp mode Normal / Quiet)
Operating temperature
5°C - 35°C
Power supply
AC100V - 240V 50 / 60Hz
450W / 1.7W / 0.35W
410W / 365W / 1.7W / 0.35W
Power consumption
(Projection / standby / standby with (normal mode / silent mode / standby
LAN OFF)
/ standby with LAN OFF)
380 mm (W) x 150 mm (H) x 430 mm (D) / 15.0 (W) x 5.9 (H) x 16.9 (D) in
Dimensions
(not including the projection)
Weight
8.5 kg / 18.7 lbs (not including projection lens unit)
Remote control, remote control dry-cell batteries, power cord, PC connection
Accessories
cable, User’s Manual / Installation Manual (this manual), warranty certificate
330-NSHA 336 W
219
Other Information
*12 When using a Standard Zoom Lens (RS-IL01ST). Varies depending on the type of lens unit.
* When lamp mode (WUX4000) is set to [Normal].
* 99.99% or more of the LCD panel pixels are effective. During projection, 0.01% or less of pixels may stay lit or unlit due to the characteristics of
the LCD panel.
* Using the projector continuously for an extended period of time may accelerate the deterioration of optical parts.
Appendix
Input signal
Input terminal
Video signals
Light source
Product Specifications
Model name
Display system
Projection Display device
lens(*1)
Optical system
Video signals
SX6000
RGB liquid crystal system
Color separation by dichroic mirror / polarizing beam splitter and color composition by prism
Type
Size / Aspect ratio
Reflective liquid crystal panel
0.7'' X3 / 16:10
Drive system
0.72'' X3 / 4:3
Active matrix system
Number dots / Total number dots
1,296,000 (1440 x 900) x 3 panels / 1,470,000 (1400 x 1050) x 3 panels /
3,888,000
4,410,000
Zoom ratio / Focal length / F value
1.5 x / f = 23.0 - 34.5 mm / F1.89 - F2.65
Zooming / Focusing system
Lens shift
Light source
Image size (projection distance) (*1)
Number of colors
Brightness (*1)
Contrast ratio
Ratio of brightness at periphery to center (*1)
Speaker
Maximum input resolution
Analog PC input
Digital PC input
Digital video input
Electric / Electric
V: -15% - +55%, H: ±10%
Input terminal
Analog PC
Component video
Audio
Noise
Operating temperature
Power supply
Power consumption (Projection / standby /
standby with LAN OFF)
Dimensions
Weight
Accessories
1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Analog PC, Digital PC (24-pin DVI connector)
Digital PC, HDMI (deep color)
Analog PC, Component (mini D-sub 15-pin)
RS-232C (D-sub 9-pin)
Wired remote control (3.5Ø stereo mini jack)
Audio signal (3.5Ø stereo mini jack x 2)
Audio signal (3.5Ø stereo mini jack)
Network connection (RJ-45)
TMDS (Transition Minimized Differential Signaling)
0.7Vp-p, positive polarity, impedance = 75Ω
Horizontal / vertical synchronization: TTL level, negative or positive polarity
Composite synchronization in G signal: 0.3Vp-p, negative polarity, impedance = 75Ω
COMPONENT: Separate Y Cb/Pb Cr/Pr signal
Y: 1Vp-p, negative synchronization, impedance = 75Ω
Cb/Pb: 0.7Vp-p, impedance = 75Ω
Cr/Pr: 0.7Vp-p, impedance = 75Ω
Impedance = 47kΩ or more
40 dB
5°C - 35°C
AC100V - 240V 50 / 60Hz
435W / 1.7W / 0.35W
380 mm (W) x 150 mm (H) x 430 mm (D) / 15.0 (W) x 5.9 (H) x 16.9 (D) in
(not including the projection)
8.5 kg / 18.7 lbs (not including projection lens unit)
Remote control, remote control dry-cell batteries, power cord, PC connection
cable, User’s Manual / Installation Manual (this manual), warranty certificate
*1 When using a Standard Zoom Lens (RS-IL01ST). Varies depending on the type of lens unit.
*
*
V: -12% - +50%, H: ±10%
330-NSHA 336 W
40'' to 600'' (1.3 to 29.7 m)
40'' to 600'' (1.3 to 28.8 m)
16,770,000 colors (full color)
5,700 lumen
6,000 lumen
1000:1 (Full white: Full black, during presentation)
88%
5W monaural x 1
1440 x 900 dots
1400 x 1050 dots
UXGA / WSXGA+ / SXGA+ / WXGA+ / WXGA / SXGA / XGA / SVGA / VGA
UXGA / WSXGA+ / SXGA+ / WXGA+ / WXGA / SXGA / XGA / SVGA / VGA
1080p, 1080i, 720p, 576p, 480p
Component video input
DVI-I IN terminal
HDMI IN terminal
ANALOG PC / COMPONENT IN terminal
CONTROL terminal
Remote terminal
AUDIO IN Terminal
AUDIO OUT Terminal
LAN terminal
Digital PC
Input signal
WX6000
99.99% or more of the LCD panel pixels are effective. During projection, 0.01% or less of pixels may stay lit or unlit due to the characteristics of the LCD panel.
Using the projector continuously for an extended period of time may accelerate the deterioration of optical parts.
220
Product Specifications
■Remote control
Type
Power supply
Operating range
Dimensions
Weight
RS-RC04
RS-RC05
DC 3.0V, using two AAA-size batterDC 3.0V, using two AA-size batteries
ies
Approx. 8 m± 25° horizontal and vertical (to infrared remote receiver)
43 mm (W) x 23 mm (H) x
51 mm (W) x 28 mm (H) x
135 mm (D) /
176 mm (D) /
1.7 (W) x 0.9 (H) x 5.3 (D) in.
2.0 (W) x 1.1 (H) x 6.9 (D) in.
56 g / 2.0 oz
100 g / 3.5 oz
■Specification of Each Lens Unit (Option)
Name
Model number
Standard Zoom Lens
Long Zoom Lens
RS-IL01ST
RS-IL02LZ
23.0 - 34.5 mm
(0.9 - 1.4'')
34.0 - 57.7 mm
(1.3 - 2.3'')
External View
Focal length
F number
1.89 - 2.65
1.99 - 2.83
Projection distance*
1.3 - 28.8 m
(4.3 - 94.5')
1.9 - 48.3 m
(6.2 - 158.5')
Width
97.4 mm (3.8'')
97.4 mm (3.8'')
Height
106.5 mm (4.2'')
106.5 mm (4.2'')
Length
173.4 mm (6.8'')
173.4 mm (6.8'')
Weight
550 g (1.2 lbs)
755 g (1.7 lbs)
Size 100 projection distance*
1.5x
1.7x
3.2 - 4.8 m
(10.5 - 15.7')
4.7 - 8.0 m
(15.4 - 26.2')
For details about the amount of lens shift, refer to page 160.
*: WUX5000 / WUX4000
Appendix
Zoom ratio
Other Information
221
Product Specifications
Name
Model number
Short Fixed Lens
Ultra Long Zoom Lens
RS-IL03WF
RS-IL04UL
12.8 mm (0.5'')
53.6 - 105.6 mm (2.1 - 4.2'')
2.0
2.34 - 2.81
0.7 - 5.2 m
(2.3 - 17.1')
4.6 - 89.0 m
(15.1 - 292.0')
97.4 mm (3.8'')
97.4 mm (3.8'')
External View
Focal length
F number
Projection distance*
Width
Height
106.5 mm (4.2'')
106.5 mm (4.2'')
Length
175.2 mm (6.9'')
184.2 mm (7.3'')
Weight
910 g (2.0 lbs)
940 g (2.1 lbs)
–
1.95x
1.7 m (5.6')
7.6 - 14.9 m (24.9 - 48.9')
Zoom ratio
Size 100 projection distance*
For details about the amount of lens shift, refer to page 160.
*: WUX5000 / WUX4000
222
Product Specifications
92 mm
430
mm (16.9'')
430mm
150
mm
150mm
(5.9'')
(3.6'')
92mm
91 mm (3.5'')
91mm
■External View
380
mm (15.0'')
380mm
128 mm (5.0'')
128mm
234.5
mm (9.2'')
234.5mm
53 mm
212 mm (8.4'')
(5.6'')
141.5 mm
141.5mm
311 311mm
mm (12.2'')
Bolt holes (M4 x 6)
for installation of
ceiling attachment
212mm
154.5
mm
154.5mm
(6.1'')
(2.1'')
53mm
This terminal is used as a computer ANALOG PC input or COMPONENT input terminal.
Use a D-sub computer cable for connection.
The terminal specifications for the ANALOG PC input and COMPONENT input are the
same.
Mini D-sub 15-pin
3
4
5
6
7
8
223
Signal
R
G
B
Monitor ID2
Ground (Horizontal
sync.)
Ground (R)
Ground (G)
Ground (B)
Pin No.
9
10
11
12
13
Signal
+5 V power
Ground (Vertical
sync.)
Monitor ID0
DDC data
Horizontal sync.
14
15
Vertical sync.
DDC clock
Other Information
Pin No.
1
2
Appendix
■ANALOG PC (WUX5000 / WUX4000), ANALOG PC-1 (WX6000 / SX6000) /
COMPONENT IN Terminal
Product Specifications
■Service Port (CONTROL)
Pin assignment
Pin No.
1
2
3
4
5
6
7
8
9
Signal
OPEN
RxD
TxD
OPEN
GND
OPEN
OPEN
OPEN
OPEN
Communication format
Communication mode : RS-232-C, asynchronous, half-duplex communication
Communication speed : 19200bps
Character length
: 8 bits
Stop bits
: 2 bits
Parity
: None
Flow control
: None
Control commands
Commands
Power supply Power on
Power off
Input status
(WX6000 /
SX6000)
Input source
acquisition
Binary representation
50h 4Fh 57h 45h 52h 20h 4Fh 4Eh 0Dh
POWER OFF<CR>
50h 4Fh 57h 45h 52h 20h 4Fh 46h 46h 0Dh
GET POWER<CR>
47h 45h 54h 20h 50h 4Fh 57h 45h 52h 0Dh
DVI-D
INPUT=D-RGB<CR>
49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h 47h 42h 0Dh
HDMI
INPUT=HDMI<CR>
49h 4Eh 50h 55h 54h 3Dh 48h 44h 4Dh 49h 0Dh
Analog PC
INPUT=A-RGB<CR>
49h 4Eh 50h 55h 54h 3Dh 41h 2Dh 52h 47h 42h 0Dh
Component
INPUT=COMP<CR>
49h 4Eh 50h 55h 54h 3Dh 43h 4Fh 4Dh 50h 0Dh
HDMI
INPUT=HDMI<CR>
49h 4Eh 50h 55h 54h 3Dh 48h 44h 4Dh 49h 0Dh
Digital PC
INPUT=D-RGB<CR>
49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h 47h 42h 0Dh
Analog PC1
INPUT=A-RGB1<CR>
49h 4Eh 50h 55h 54h 3Dh 41h 2Dh 52h 47h 42h 31h 0Dh
Analog PC2
INPUT=A-RGB2<CR>
49h 4Eh 50h 55h 54h 3Dh 41h 2Dh 52h 47h 42h 32h 0Dh
Component
INPUT=COMP<CR>
49h 4Eh 50h 55h 54h 3Dh 43h 4Fh 4Dh 50h 0Dh
GET INPUT<CR>
47h 45h 54h 20h 49h 4Eh 50h 55h 54h 0Dh
Power status
acquisition
Input status
(WUX5000 /
WUX4000)
ASCII representation
POWER ON<CR>
224
Product Specifications
Commands
Image mode
Image mode
Standard
IMAGE=STANDARD<CR>
Presentation
IMAGE=PRESENTATION<CR>
49h 4Dh 41h 47h 45h 3Dh 50h 52h 45h 53h
45h 4Eh 54h 41h 54h 49h 4Fh 4Eh 0Dh
VividPhoto
IMAGE=VIVID_PHOTO<CR>
49h 4Dh 41h 47h 45h 3Dh 56h 49h 56h 49h 44h 5Fh 50h 48h
4Fh 54h 4Fh 0Dh
Photo /sRGB
IMAGE=PHOTO_SRGB<CR>
49h 4Dh 41h 47h 45h 3Dh 50h 48h 4Fh 54h 4Fh 5Fh 53h 52h
47h 42h 0Dh
Dynamic
IMAGE=DYNAMIC<CR>
49h 4Dh 41h 47h 45h 3Dh 44h 59h 4Eh 41h 4Dh 49h 43h
0Dh
Video
IMAGE=VIDEO<CR>
49h 4Dh 41h 47h 45h 3Dh 56h 49h 44h 45h 4Fh 0Dh
Cinema
IMAGE=CINEMA<CR>
49h 4Dh 41h 47h 45h 3Dh 43h 49h 4Eh 45h 4Dh 41h 0Dh
User 1
IMAGE=USER_1<CR>
49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 52h 5Fh 31h 0Dh
User 2
IMAGE=USER_2<CR>
49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 52h 5Fh 32h 0Dh
User 3
IMAGE=USER_3<CR>
49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 52h 5Fh 33h 0Dh
User 4
IMAGE=USER_4<CR>
49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 52h 5Fh 34h 0Dh
User 5
IMAGE=USER_5<CR>
49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 52h 5Fh 35h 0Dh
GET IMAGE<CR>
47h 45h 54h 20h 49h 4Dh 41h 47h 45h 0Dh
BRI=<value><CR>
42h 52h 49h 3Dh <numeric code> 0Dh
GET BRI<CR>
47h 45h 54h 20h 42h 52h 49h 0Dh
SHARP=<value><CR>
53h 48h 41h 52h 50h 3Dh <numeric code> 0Dh
GET SHARP<CR>
47h 45h 54h 20h 53h 48h 41h 52h 50h 0Dh
CONT=<value><CR>
43h 4Fh 4Eh 54h 3Dh <numeric code> 0Dh
GET CONT<CR>
47h 45h 54h 20h 43h 4Fh 4Eh 54h 0Dh
Brightness value
setting
Brightness
acquisition
Sharpness
Sharpness value
setting
Sharpness
acquisition
Contrast
Contrast value
setting
Contrast
acquisition
Aspect
(WUX5000 /
WUX4000)
ASPECT=AUTO<CR>
41h 53h 50h 45h 43h 54h 3Dh 41h 55h 54h 4Fh 0Dh
4:3
ASPECT=4:3<CR>
41h 53h 50h 45h 43h 54h 3Dh 34h 3Ah 33h 0Dh
16:9
ASPECT=16:9<CR>
41h 53h 50h 45h 43h 54h 3Dh 31h 36h 3Ah 39h 0Dh
Zoom
ASPECT=ZOOM<CR>
41h 53h 50h 45h 43h 54h 3Dh 5Ah 4Fh 4Fh 4Dh 0Dh
True size
ASPECT=TRUE<CR>
41h 53h 50h 45h 43h 54h 3Dh 54h 52h 55h 45h 0Dh
Full
ASPECT=FULL<CR>
41h 53h 50h 45h 43h 54h 3Dh 46h 55h 4Ch 4Ch 0Dh
Auto
ASPECT=AUTO<CR>
41h 53h 50h 45h 43h 54h 3Dh 41h 55h 54h 4Fh 0Dh
4:3
ASPECT=4:3<CR>
41h 53h 50h 45h 43h 54h 3Dh 34h 3Ah 33h 0Dh
16:9
ASPECT=16:9<CR>
41h 53h 50h 45h 43h 54h 3Dh 31h 36h 3Ah 39h 0Dh
16:10
ASPECT=16:10<CR>
41h 53h 50h 45h 43h 54h 3Dh 31h 36h 3Ah 31h 30h 0Dh
Zoom
ASPECT=ZOOM<CR>
41h 53h 50h 45h 43h 54h 3Dh 5Ah 4Fh 4Fh 4Dh 0Dh
True size
ASPECT=TRUE<CR>
41h 53h 50h 45h 43h 54h 3Dh 54h 52h 55h 45h 0Dh
GET ASPECT<CR>
47h 45h 54h 20h 41h 53h 50h 45h 43h 54h 0Dh
Normal
LAMP=NORMAL<CR>
4Ch 41h 4Dh 50h 3Dh 4Eh 4Fh 52h 4Dh 41h 4Ch 0Dh
Quiet
LAMP=SILENT<CR>
4Ch 41h 4Dh 50h 3Dh 53h 49h 4Ch 45h 4Eh 54h 0Dh
GET LAMP<CR>
47h 45h 54h 20h 4Ch 41h 4Dh 50h 0Dh
Aspect value
acquisition
Lamp mode
Lamp mode
value acquisition
225
Other Information
Auto
Appendix
Aspect
(WX6000 /
SX6000)
Binary representation
49h 4Dh 41h 47h 45h 3Dh 53h 54h 41h 4Eh 44h 41h 52h 44h
0Dh
Image mode
acquisition
Brightness
ASCII representation
Product Specifications
Commands
Blank
Blank On
Blank Off
Blank acquisition
ASCII representation
Binary representation
BLANK=ON<CR>
42h 4Ch 41h 4Eh 4Bh 3Dh 4Fh 4Eh 0Dh
BLANK=OFF<CR>
42h 4Ch 41h 4Eh 4Bh 3Dh 4Fh 46h 46h 0Dh
GET BLANK<CR>
47h 45h 54h 20h 42h 4Ch 41h 4Eh 4Bh 0Dh
226
Product Specifications
Appendix
Other Information
227
Index
Numerics
D
6-axis color adjust ............................... 117
D. ZOOM ............................................... 84
D.SHIFT / KEYSTONE
(WUX5000 / WUX4000) ........ 67, 68, 76
DHCP .................................................. 175
Digital Image Shift ................................. 67
Digital PC ................................ 50, 59, 164
Direct power on .................................. 121
Display Resolution (Preparing the Computer) ..................................................... 61
Display settings menu .......................... 88
Displaying logo ................................... 106
DVI .......................................... 50, 59, 164
DVI-D IN (WUX5000 / WUX4000) ......... 50
DVI-D IN terminal
(WUX5000 / WUX4000) .................... 40
DVI-I IN (WX6000 / SX6000) ........... 48, 50
DVI-I IN terminal (WX6000 / SX6000) ... 41
Dynamic gamma ................................. 116
A
Adjusting Keystone Distortion .............. 76
Adjusting the focus ............................... 73
Adjusting the Volume ............................ 83
Air filter ................................................ 193
Ambient light ....................................... 115
Analog PC ............................... 47, 59, 164
ANALOG PC / COMPONENT IN
terminal (WUX5000 /
WUX4000) ........ 40, 47, 49, 53, 59, 164
Analog PC-1 (WX6000 / SX6000) ... 47, 48
Analog PC-1 / COMPONENT IN
terminal (WX6000 /
SX6000) ............ 41, 48, 49, 54, 59, 164
Analog PC-2 (WX6000 / SX6000) ......... 48
Analog PC-2 / DVI-I IN terminal (WX6000 /
SX6000) .......................... 41, 48, 50, 59
ASPECT ................................................ 70
Aspect .............................. 63, 69, 93, 207
AUDIO IN
terminal ............ 40, 41, 47, 50, 53, 139
AUDIO OUT terminal .......... 40, 41, 51, 55
Auto (Aspect) ........................................ 69
AUTO PC .............................................. 62
F
Factory defaults .................................. 140
FOCUS .................................................. 73
FREEZE ................................................. 82
G
Guide .................................................. 126
B
H
Beep ................................................... 122
BLANK .................................................. 82
Brightness ........................................... 111
HDMI ................................. 51, 52, 59, 164
HDMI color space ................................. 99
HDMI IN terminal ................ 40, 41, 51, 52
HDMI input level ................................... 98
HDMI over scan .................................. 100
Horizontal pixels ................................... 97
Horizontal position ................................ 96
C
Ceiling mounted .................................. 104
Channel setting ................................... 124
Component ....................... 53, 59, 95, 164
Connection to Computer ....................... 47
Contrast .............................................. 112
228
I
IMAGE ................................................... 79
Image adjustment menu ................. 88, 89
Image flip H/V (Ceiling mounted /
Rear projection) .............................. 104
Image mode ........................................ 109
Index
Image Mode (Image Quality) ................ 78
Information .............................. 88, 89, 141
INPUT .................................................... 60
Input settings (WX6000 / SX6000) ........ 89
Input signal select ..................... 59, 94, 95
Input Terminal ....................................... 40
Connecting to AV Equipment ............ 52
Connection to Computer ................... 47
Install settings (WX6000 / SX6000) ....... 89
K
Key lock .............................................. 123
Keystone ............................................... 76
KEYSTONE (WX6000 / SX6000) ........... 76
L
LAMP (WUX4000) ............................... 119
Lamp counter ...................................... 135
Lamp mode (WUX4000) ..................... 119
Lamp replacement .............. 135, 195, 196
LAN port .......................................... 40, 41
Language ............................................ 125
LED indicator ...................................... 202
M
Memory Color Correction .................... 117
MENU .............................................. 88, 89
Menu display time ............................... 132
Menu position ...................................... 102
MUTE .................................................... 83
N
OK ................................................... 35, 36
R
Rear projection ....................................104
Register password ..............................129
Remote control ..................29, 34, 36, 124
Reset ...........................................119, 140
S
Screen aspect .......................63, 107, 207
Screen color ........................................103
Screen When Blank .............................106
Selecting a language ....................57, 125
Selecting an Image Quality .................109
Setting Display Status ...........................93
Setting Various Functions ....................120
Sharpness ...........................................113
Side Control ...........................................38
Signal type ..........................................218
System settings menu .....................88, 89
T
TCP/IP settings ....................................175
Test pattern
(WX6000 / SX6000) .................138, 217
Total dots ...............................................95
Tracking .................................................96
True size (Aspect) .................................69
Turning on external monitor output (preparing the notebook computer) .............58
229
Index
O
Password settings ...............................128
Performing Gamma Correction ...........113
PJLink ..................................................174
Positional lock (WX6000 / SX6000) .....139
POWER ...................................56, 80, 121
Power Management ..............................57
Power management mode (settings) ..120
Power Saving (Power Management) .....57
Progressive .........................................101
Projector on .........................................106
P-TIMER (WUX5000 / WUX4000) ..........85
Appendix
Network function ................................. 172
Network Password setting .................. 173
Network setting ............................... 88, 89
Network setting initialization ................ 176
Network setting lock ............................ 171
Noise reduction ................................... 116
P
Index
V
Vertical pixels ........................................ 98
Vertical Position .................................... 97
VOL ....................................................... 83
W
WARNING indicator ...................... 38, 202
Z
ZOOM ................................................... 71
Zoom (Aspect) ...................................... 69
Zooming an Image ................................ 84
230
Option
• Lamp
• Air filter
Part No.: RS-LP06 (WUX4000)
RS-LP07 (WUX5000 / WX6000 /
SX6000)
Part No.: RS-FL01
• Standard Zoom Lens
• Ceiling attachment
Part No.: RS-IL01ST
• Long Zoom Lens
Part No.: RS-CL11
• Ceiling-mount pipe (400 - 600 mm)
Part No.: RS-IL02LZ
• Short Fixed Lens
Part No.: RS-CL08*
• Ceiling-mount pipe (600 - 1000 mm)
Part No.: RS-IL03WF
• Ultra Long Zoom Lens
Part No.: RS-CL09*
Part No.: RS-IL04UL
• Remote control
• Black top panel
Part No.: RS-RC04 (WUX5000 / WUX4000)
RS-RC05 (WX6000 / SX6000)
Part No.: RS-TC01
* Use the above materials to hang the projector from the ceiling. For details, refer to the assembly and
installation manual provided with the ceiling attachment RS-CL11.
• Installing / Removing the Lens Unit
It is possible to use replace the lens unit. Regarding installation and replacement of the lens unit, contact a qualified technician or the Canon Customer Support Center for further information. Do not
attempt installation and replacement of the lens unit yourself.
• Precaution for qualified technicians
Before installation and replacement the lens unit, check the part number and use the correct lens unit.
231
Menu Configuration
Display settings Menu
Aspect
Digital PC / Analog PC
P93
Progressive
Auto *
Full
16:9
4:3
True size
Component / HDMI
P101
Off
On
Auto *
Menu position
P102
Screen color
Normal *
Greenboard
HDMI
Auto *
Full
16:9
4:3
Zoom
True size
Image flip H/V
Auto *
16:9
4:3
Zoom
True size
Input signal
select
Analog PC
P94
HDMI input level
HDMI
HDMI
P95
P96
P96
P97
P97
P98
P98
P99
Auto *
RGB
YCbCr
HDMI over scan *1
HDMI
P105
Screen when blank
Black *
Blue
P106
Projector on
Skip
Canon logo*
P106
16:10*
16:9
4:3
16:9 D. image shift
4:3 D. image shift
P107
Screen aspect
Auto *
Normal
Expanded
HDMI color space
Black
Blue*
Return
Analog PC
Total dots
Tracking
Horizontal position
Vertical position
Horizontal pixels
Vertical pixels
P104
No signal screen
P95
Auto *
1080p
1080i
1035i
720p
576p
480p
576i
480i
Input signal
settings
None *
Ceiling mounted
Rear
Rear, Ceiling mounted
User screen
settings
640x480
:
1920x1200
Component
Red /
Green / Blue
Adjust
Component
P103
P100
Off
On
232
Menu Configuration
Image Adjustment Menu
Image mode
COMMON
P109
Standard *
Photo/sRGB
User 1 - 5 (as creating
profile)
Advanced adjustment
Ambient light
Off *
Adjust
Digital PC / Analog PC /
HDMI (when [HDMI In] P109
is [Computer])
Presentation
VividPhoto
Component / HDMI
(when [HDMI In] is [Auto])
Dynamic
Video
Cinema
P115
Type
Tungsten
Fluorescent
Fluorescent H
Level
L
M
H
P109
Return
Noise reduction *2
Component / HDMI P116
Off
Weak
Middle
Strong
Create Profile
Baseline Image
Mode (when user
memory is selected)
Brightness
Contrast
Sharpness
Gamma
P110
P110
P111
P112
P113
P113
Dynamic gamma
Off *1
Weak *2
Middle
Strong
P116
Color adjustment
P114
Mem. color correct *3
Off
L
M
H
P117
Color level
Color balance
Color temperature
R Gain
G Gain
B Gain
R Offset
G Offset
B Offset
6-axis color adjust
Off *
Adjust
P117
Hue / Saturation /
Brightness
Reset
Fine-Tune Gamma P118
Return
Lamp mode *4
Normal *
Quiet
P119
Reset
OK / Cancel
P119
Factory default settings for *1, *2 and *3 are set according to the following conditions.
*1: • For Analog PC, Digital PC or HDMI (when [HDMI
In] is [Computer]), the factory default is [Off].
• For Component, and HDMI (when [HDMI In] is
[Auto]), the factory default is [On].
*2: • For HDMI (when [HDMI In] is [Auto]), the factory
default is [Off].
• For Component, the factory default is [Weak].
*3: • For HDMI (when [HDMI In] is [Computer]), Digital PC or Analog PC, if any image mode is used
except [VividPhoto], the factory default is [Off].
If [VividPhoto] is used, the factory default is
[Middle].
• For HDMI (when [HDMI In] is [Auto]) or Component, the factory default is [Weak], regardless of
the image mode.
*4: • WUX4000
233
Menu Configuration
System Settings Menu
Power management
mode
Network Setting Menu
P120
Off *
Standby
Exit
Direct power on
Off *
On
P121
Beep
Off
On *
P122
Key lock
Off *
Main unit
Remote control
P123
Ch1
Ch2
Ch3
Ch4
Independent *
P124
English
German
French
Italian
Spanish
Portuguese
P125
Remote control
Language
Swedish
Russian
Dutch
Finnish
Norwegian
Turkish
Polish
Hungarian
Czech
Danish
Arabic
Chinese
(Simplified)
Chinese
(Traditional)
Korean
Japanese
Network setting lock
Unlock
Lock *
P171
Network function
Off *
On
P172
Network Password setting
Off
On *
P173
Register Network Password
Password input
PJLink
Off
On *
P174
DHCP
Off *
On
P175
TCP/IP setting
IP address
Subnet mask
Gateway address
Enter
P175
Network setting initialization
Yes / No
Guide
Off
On *
P126
Information Menu
Show Input Status
Off
On *
P127
HDMI In
Auto *
Computer
P127
Model name
Input signal
Firmware
Serial No.
IP address
Gateway address
E-mail sender address
E-mail recipient address
Projector name
Location
System information ID
Other settings
Password settings
Off *
On
P128
Register password
Password input
P129
Lens Ctrl Lock
Off *
On
P130
Lens shift Reset
Lens shift Reset
P131
Menu display time
Normal *
Extended
P132
Overheat Warning Display
Off *
P133
On
Deflicker
Off *
Adjust
Lamp counter
Return
P135
Reset (OK / Cancel)
Factory defaults
OK / Cancel
P173
P134
P140
Return
234
*: Factory defaults (setting after reset)
P176
P141
Menu Configuration
Input Settings Menu
Aspect
Digital PC / Analog PC-1 / 2 / P93
HDMI (when [HDMI In] is
[PC])
Auto *
16:10
16:9
4:3
True size
HDMI (when [HDMI In] is
[Auto]) /Component
Auto *
16:10
16:9
4:3
Zoom
True size
Auto PC
P94
Input signal
select
Analog PC-1 / 2
P94
640 x 480
:
1920 x1200
Input signal settings
Analog PC-1 / 2
Total dots
Tracking
Horizontal position
Vertical position
Horizontal pixels
Vertical pixels
HDMI input level
HDMI color
space
P95
P96
P96
P97
P97
P98
HDMI
Auto *
Normal
Expanded
P98
HDMI
P99
Auto *
RGB
YCbCr
HDMI over
scan*1
HDMI
P100
Off
On
Progressive
Component / HDMI
Off
On
Auto *
P101
235
Menu Configuration
Image Adjustment Menu
Image mode
COMMON
P109
Standard *
Photo/sRGB
User 1 - 5 (when creating
profile)
Digital PC /
Analog PC-1/2 /
HDMI (when [HDMI In] is P109
[Computer])
Presentation
VividPhoto
Component / HDMI (when
P109
[HDMI In] is [Auto])
Dynamic
Video
Cinema
Advanced adjustment
Ambient light
Off *
Adjust
P110
Color adjustment
P114
Type
Tungsten
Fluorescent
Fluorescent
H
Level
L
M
H
Return
Noise reduction *2
Create Profile
Save profile
(When profile is
selected)
Baseline Image
Mode (When profile is selected)
Brightness
Contrast
Sharpness
Gamma
P115
Component / HDMI P116
Off
Weak
Middle
Strong
P110
Dynamic gamma
Off *1
Weak *2
Middle
Strong
P116
Mem. color correct *3
Off
L
M
H
P117
P111
P111
P112
P113
P113
6-axis color adjust
Color level
Color balance
Color temperature
R Gain
G Gain
B Gain
R Offset
G Offset
B Offset
Off *
Adjust
P117
Hue / Saturation /
Brightness
Reset
Fine-Tune Gamma P118
Return
Reset
236
OK / Cancel
P119
Menu Configuration
Install settings Menu
Positional lock
Off *
On
P139
Lamp warning display
Off
On *
P135
Test pattern
Off *
On
P138
Filter warning display
Off
On *
P137
Screen aspect
16:10 *5
16:9
4:3 *4
16:10 D. image shift
(SX6000)
16: 9 D. image shift
4:3 D. image shift
(WX6000)
P107
Keystone adjustment
Keystone adjustment
P108
Digital image shift
D. image shift adjustment P108
Image flip H/V
None*
Ceiling mounted
Rear
Rear, Ceiling mounted
P104
Lens shift reset
Lens shift reset
P131
*1 - *5: Factory default settings are set according to the
following conditions.
*1: • For Analog PC-1/2, Digital PC or HDMI (when
[HDMI In] is [Computer]), the factory default is
[Off].
• For Component, and HDMI (when [HDMI In] is
[Auto]), the factory default is [On].
*2: • For HDMI (when [HDMI In] is [Auto]), the factory
default is [Off].
• For Component, the factory default is [Weak].
*3: • For HDMI (when [HDMI In] is [Computer]), Digital PC or Analog PC-1/2, if any image mode is
used except [VividPhoto], the factory default is
[Off]. If [VividPhoto] is used, the factory default
is [Middle].
• For HDMI (when [HDMI In] is [Auto]) or Component, the factory default is [Weak], regardless of
the image mode.
*4: • SX6000
*5: • WX6000
Audio in terminal select
HDMI
Off
Audio in 1
Audio in 2
HDMI *
P139
Digital PC
Off
Audio in 1
Audio in 2 *
P139
Analog PC-1
Off
Audio in 1 *
Audio in 2
P139
Analog PC-2
Off
Audio in 1
Audio in 2 *
P139
Component
Off
Audio in 1 *
Audio in 2
P139
Screen color
Normal *
Greenboard
Adjust
P103
On screen
Menu position
P102
Guide
Off
On *
P126
Show input status
Off
On *
P127
Overheat warning display
Off *
On
P133
Menu display time
Normal *
Extended
P132
237
Menu Configuration
System Settings Menu
Network Setting Menu
Power management mode
Off *
Standby
Exit
P120
Direct power on
Off *
On
P121
User screen settings
No signal screen
Black
Blue *
P105
Screen when blank
Black *
Blue
P106
Projector on
Skip
Canon logo *
P106
Network setting lock
Unlock
Lock *
P171
Network function
Off *
On
P172
Network Password setting
Off
On *
P173
Register Network Password
Password input
P173
PJLink
Off
On *
P174
Beep
Off
On *
P122
DHCP
Off *
On
P175
Key Repeat
Off
On *
P122
TCP/IP setting
P175
Key lock
Off *
Main unit
Remote (wireless)
P123
IP address
Subnet mask
Gateway address
Enter
Remote control
Ch1
Ch2
Ch3
Ch4
Independent*
P124
HDMI In
Auto *
Computer
P127
Language
English
German
French
Italian
Spanish
Portuguese
Swedish
Russian
Dutch
Finnish
Norwegian
Turkish
Polish
Hungarian
Czech
Danish
Arabic
Chinese
(Simplified)
Chinese
(Traditional)
Korean
Japanese
P125
Off *
On
P128
Register password
Password input
P129
Gamma restore
Off
Adjust
P134
Lamp counter
Return
P135
Reset (OK / Cancel)
Filter counter
Return
P137
Reset (OK / Cancel)
Factory defaults
OK / Cancel
Return
Yes / No
P140
238
P176
Information Menu
Model name
Input signal
Firmware
Serial No.
IP address
Gateway address
E-mail sender address
E-mail recipient address
Projector name
Location
System information ID
*: Factory defaults (setting after reset)
Other settings
Password settings
Network setting initialization
P141
Menu Configuration
239
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo
146-8501, Japan
U.S.A.
CANON U.S.A. INC.
One Canon Plaza, Lake Success, NY 110421198, U.S.A.
For all inquires concerning this product, call toll
free in the U.S. 1-800-OK-CANON
CANADA
CANON CANADA INC. HEADQUARTERS
6390 Dixie Road, Mississauga, Ontario L5T
1P7, Canada
CANON CANADA INC. MONTREAL BRANCH
5990, Côte-de-Liesse, Montréal Québec H4T
1V7, Canada
CANON CANADA INC. CALGARY OFFICE
2828, 16th Street, N.E. Calgary, Alberta T2E
7K7, Canada
For all inquiries concerning this product, call toll
free in Canada
1-800-OK-CANON
EUROPE, AFRICA & MIDDLE EAST
CANON EUROPE LTD.
3 The Square Stockley Park, Uxbridge, Middlesex, UB11 1ET United Kingdom
CANON EUROPA N.V.
Bovenkerkerweg 59-61, 1185 XB Amstelveen,
The Netherlands
CANON FRANCE S.A.S
17, quai du President Paul Doumer, 92414
Courbevoie Cedex, France
CANON UK LTD.
Woodhatch Reigate Surrey RH2 8BF, United
Kingdom
CANON DEUTSCHLAND GmbH
Europark Fichtenhain A10, 47807 Krefeld, Germany
CANON ITALIA S.p.A.
Via Milano 8 I-20097 San Donato Milanese, Milano, Italy
CANON Schweiz AG
Geschäftsbereich Wiederverkauf, Industriestrasse 12, CH-8305 Dietlikon,
Switzerland
CANON GMBH
Zetschegasse 11, A-1230 Wien, Austria
CANON España, S.A.
Av. De Europa, 6 Alcobendas 28108 Madrid,
Spain
CANON PORTUGAL S.A.
Rua Alfredo da Silva, 14 Alfragide 2610-016
Amadora, Portugal
CANON Belgium N.V. / S.A.
Berkenlaan 3, 1831 Diegem (Mechelen), Belgium
CANON Netherland NV
Neptunusstraat 1, 2132 JA Hoofddorp, The
Netherlands
CANON LUXEMBOURG S.A.
Rue des Joncs 21, L-1818 Howald, Luxembourg
CANON DANMARK A / S
Knud Hoejgaards Vej 1 DK-2860 Soeborg, Danmark
CANON OY
Huopalahdentie 24 PL 1 00351 Helsinki, Finland
CANON SVENSKA AB
Gustav III:s Boulevard 26 169 88 Solna, Sweden
CANON NORGE as
Hallagerbakken 110, Postboks 33, Holmlia,
1201 Oslo, Norway
CENTRAL & SOUTH AMERICA
CANON LATIN AMERICA, INC.
703 Waterford Way, Ste. 400 Miami, FL 33126,
U.S.A.
ASIA
CANON (China) Co., Ltd.
15F Jinbao Building No.89 Jinbao Street,
Dongcheng District, Beijing 100005, China
CANON HONGKONG CO., LTD.
19 / F., The Metropolis Tower, 10 Metropolis
Drive, Hunghom, Kowloon, Hong Kong
CANON SINGAPORE PTE. LTD.
1 HarbourFront Avenue, #04-01 Keppel Bay
Tower, Singapore 098632
CANON KOREA CONSUMER IMAGING INC.
Canon BS Tower 5F, #168-12 Samseong-dong,
Gangnam-gu, Seoul, Korea
OCEANIA
CANON AUSTRALIA PTY. LTD.
1 Thomas Holt Drive, North Ryde, N.S.W. 2113,
Australia
CANON NEW ZEALAND LTD.
Akoranga Business Park, Akoranga Drive,
Northcote, Auckland, New Zealand
©CANON INC.2011