2 YEAR WARRANTY

IPL6500AU

SKIN CHART

THE SKIN CHART

HAIR COLOUR

SKIN COLOUR

WARNING: i-LIGHT

®

is not suitable for very dark or black skin, white/grey or very light blonde/red hair.

For facial use: Only suitable for female facial use below the cheekbone.

DO NOT use on or around the eyes, eyebrows or eyelashes. Doing so can cause serious and permanent eye injury.

SKIN CHART

THE SKIN CHART

HAIR COLOUR

SKIN COLOUR

WARNING: i-LIGHT

®

is not suitable for very dark or black skin, white/grey or very light blonde/red hair.

For facial use: Only suitable for female facial use below the cheekbone.

DO NOT use on or around the eyes, eyebrows or eyelashes. Doing so can cause serious and permanent eye injury.

3

4

Thank you for buying your new Remington® product.

Please read these instructions carefully and keep them safe. Remove all packaging before use.

IMPORTANT SAFETY INSTRUCTIONS

1 WARNING – TO REDUCE THE RISK OF BURNS, ELECTROCUTION, FIRE, OR INJURY TO PERSONS:

2 Use this appliance only for its intended use described in this manual.

3 Do not use if it is damaged or malfunctions.

4 Do not leave the appliance unattended while plugged in.

5 Keep the power plug and cord away from heated surfaces.

6 Do not use the product with a damaged cord. A replacement can be obtained via our International

Service Centres.

7 Store the product at a temperature between 15° and 35°C.

8 Only use the parts supplied with the appliance.

9 Do not twist or kink the cable and don’t wrap it around the appliance.

10 The body of this appliance is not washable or water resistant. Do not put the appliance in liquid; do not use it near water in a bath tub, basin or other vessel; and don’t use it outdoors.

11 Make sure the power cable and adaptor do not get wet. Do not reach for your unit if it has fallen into water - immediately unplug it from the electrical outlet.

12 Do not plug or unplug the appliance with wet hands.

13 This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been supervised/instructed and understand the hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised.

14 Keep the appliance and cable out of reach of children under 8 years.

15 This appliance is not intended for commercial or salon use.

i-LIGHT® KEY FEATURES

Figure1

1 2

18

3

4

5

6

7

8

9

10

11

13

12

17

14

14

4

4

13

12

16

15

19

i-LIGHT® KEY FEATURES

Figure1

1 2

18

3

4

5

6

7

8

9

10

11

13

12

17

14

14

4

4

13

12

16

15

19

5

6



KEY FEATURES

1 Power Switch

2 Power Inlet

3 Base Unit

4 Hand Piece

5 Flash Button

6 Energy Level Selection Button

7 Cool Down Mode Indicator

8 Bulb Status Indicator Display

9 Energy Level Indicator

10 Skin Tone Sensor

11 Hand Piece Cord

12 Flash Window

13 Skin Contact Sensors

14 Attachment Release Buttons

15 Bulb

16 Body Attachment

17 Power Cord

18 Lint Free Cloth

19 Facial Attachment



GETTING STARTED

Be patient when first using your i-LIGHT®, as with any new product, it may take a little while to familiarise yourself with the product. Take the time to acquaint yourself with your i-LIGHT® as we are confident you will receive years of enjoyable use and complete satisfaction.



GETTING ACQUAINTED WITH i-LIGHT®

, What is i-

The iLIGHT

LIGHT ?

® system is a revolutionary light-based device designed for the removal of unwanted body hair and female facial hair at home.

iLIGHT®

®

utilises similar clinically-proven technology that professional dermatologists and salons use, optimised for personal treatment.

, What is Intense Pulse Light (IPL) and how does i-

LIGHT® work?

IPL - (Intense Pulsed Light) is a well-established technology used worldwide for over 15 years. iLIGHT®

The pulse works under the skin’s surface to target hairs at the root, helping to stop their growth. (Fig 1) uses

Fig. 1

The energy in the pulse of light targets dark colouring, and best results are seen on darker hair.

To avoid targeting (and possibly damaging) dark skin, you should only use itones (I-IV).

LIGHT®

on light to medium skin

, What to expect from i-LIGHT®

Results aren’t immediate, and individual results vary. Most users will begin to notice fewer hairs within 1-2 weeks after beginning treatment. During this time it may look like the hair is still growing, but it is actually being ‘pushed out’ (Fig. 2).

Fig. 2



GETTING ACQUAINTED WITH i-LIGHT®

, What is i-

The iLIGHT

LIGHT ?

® system is a revolutionary light-based device designed for the removal of unwanted body hair and female facial hair at home.

iLIGHT®

®

utilises similar clinically-proven technology that professional dermatologists and salons use, optimised for personal treatment.

, What is Intense Pulse Light (IPL) and how does i-

LIGHT® work?

IPL - (Intense Pulsed Light) is a well-established technology used worldwide for over 15 years. iLIGHT®

The pulse works under the skin’s surface to target hairs at the root, helping to stop their growth. (Fig 1) uses

Fig. 1

The energy in the pulse of light targets dark colouring, and best results are seen on darker hair.

To avoid targeting (and possibly damaging) dark skin, you should only use itones (I-IV).

LIGHT®

on light to medium skin

, What to expect from i-LIGHT®

Results aren’t immediate, and individual results vary. Most users will begin to notice fewer hairs within 1-2 weeks after beginning treatment. During this time it may look like the hair is still growing, but it is actually being ‘pushed out’ (Fig. 2).

Fig. 2

7

phase are susceptible to treatment, which is why multiple treatments are required for optimal results.

Fig. 3

Fig. 3 Fig. 4

8

Catagen Phase

Telogen Phase

It’s important to continue with the full treatment regime and top-up treatments to ensure that every active hair is treated.

, Treatment Regime

A full treatment regime is once every two weeks for three treatments.

Individual results may vary, so multiple treatments may be required for optimal results. is perfectly normal and should be expected.

After completing the initial treatment regime, top-up treatments will provide even better results.

Continuous regular weekly use will give good results within 6-12 weeks (darker skin tones may take longer).

, NOTE: You should avoid treating the same area multiple times in one session, as it will not improve

WARNINGS AND SAFETY PRECAUTIONS

IMPORTANT SAFETY CAUTIONS

Before you start using i-LIGHT®:

Be sure to read all Warnings and Safety Information. Before you begin, check to see if i-LIGHT® is suitable for you.

Use the skin and hair chart at the front of this manual and the integrated skin sensor to determine if this device is right for you.

Consult the hair chart at the front of this manual to ensure the device is right for you.

, Skin Type

• Do not use on naturally dark skin, as it may result in burns, blisters and changes in skin colour.

• Do not use on tanned skin or after recent sun exposure, as it may cause burns or skin injury.

• i-LIGHT®

, Areas not to treat:

• Do not use on the scalp or ears.

• Do not use on male face or neck.

• Do not use above the cheekbone (female facial use).

• Do not use on nipples, areola or genitals.

• Do not use if you have tattoos or permanent makeup in the area to be treated.

•  Do not use on dark brown or black spots such as moles, birth marks or freckles.

•  Do not use on an area of recent surgery, deep peel, laser resurfacing, scars or skin that has been damaged with burns or scalds.

, When not to use/When to avoid using i-LIGHT®

• DO NOT use if you have tanned skin in the intended treatment area, as your skin may be too dark and treatment in tanned areas could temporarily cause skin swelling, blisters, or could change the colour of your skin. Wait until your tan has faded before treating. 

• DO NOT use on skin with cosmetics applied, as treating in those areas could temporarily cause skin swelling, blisters or could change the colour of your skin. Make sure to thoroughly clean the intended treatment area prior to use.

• DO NOT the same treatment spot multiple times during the same session, as this could temporarily cause skin swelling, blisters, or could change the colour of your skin.

• DO NOT treat any area more than once per week, as this will not speed up results, but could increase likelihood of skin swelling, blistering or changing the colour of your skin.

• DO NOT use on damaged skin, including open wounds, cold sores, sunburns, or areas where you have had a skin peel or other skin resurfacing procedure within the last 6-8 weeks.

• DO NOT use on irritated skin, including rashes or swollen skin. These conditions can make the skin

• DO NOT use if your skin is sensitive to light. In order to determine if you can use i-LIGHT®, perform a test on a small patch of skin and wait 24 hours to determine if there are any adverse reactions before treating more broadly.

• DO NOT use if you are or may be pregnant or are breast-feeding. i-LIGHT® has not been tested on pregnant women. Hormonal changes are common during pregnancy or breast-feeding and could increase skin sensitivity and the risk of skin injury.

• DO NOT against any material other than skin.

• DO NOT use i-LIGHT® for any purpose other than hair removal.

• DO NOT treat any area where you may someday want your hair to grow back. The results may be permanent and irreversible.

, as this may result in undesired hair re-growth.

• DO NOT use on the face if you have a history of cold sores; use of IPL or any treatment that irritates skin can cause a recurrence of cold sores.

• If you’ve had professional or clinical or self-administered laser or IPL or electrolysis hair removal treatments, wait at least 6 months before using i-LIGHT®. If you’ve waxed, plucked or epilated hair in the treatment area, wait at least 6 weeks before using i-LIGHT® . The device uses the hair under your skin to

, Areas not to treat:

• Do not use on the scalp or ears.

• Do not use on male face or neck.

• Do not use above the cheekbone (female facial use).

• Do not use on nipples, areola or genitals.

• Do not use if you have tattoos or permanent makeup in the area to be treated.

•  Do not use on dark brown or black spots such as moles, birth marks or freckles.

•  Do not use on an area of recent surgery, deep peel, laser resurfacing, scars or skin that has been damaged with burns or scalds.

, When not to use/When to avoid using i-LIGHT®

• DO NOT use if you have tanned skin in the intended treatment area, as your skin may be too dark and treatment in tanned areas could temporarily cause skin swelling, blisters, or could change the colour of your skin. Wait until your tan has faded before treating. 

• DO NOT use on skin with cosmetics applied, as treating in those areas could temporarily cause skin swelling, blisters or could change the colour of your skin. Make sure to thoroughly clean the intended treatment area prior to use.

• DO NOT the same treatment spot multiple times during the same session, as this could temporarily cause skin swelling, blisters, or could change the colour of your skin.

• DO NOT treat any area more than once per week, as this will not speed up results, but could increase likelihood of skin swelling, blistering or changing the colour of your skin.

• DO NOT use on damaged skin, including open wounds, cold sores, sunburns, or areas where you have had a skin peel or other skin resurfacing procedure within the last 6-8 weeks.

• DO NOT use on irritated skin, including rashes or swollen skin. These conditions can make the skin

• DO NOT use if your skin is sensitive to light. In order to determine if you can use i-LIGHT®, perform a test on a small patch of skin and wait 24 hours to determine if there are any adverse reactions before treating more broadly.

• DO NOT use if you are or may be pregnant or are breast-feeding. i-LIGHT® has not been tested on pregnant women. Hormonal changes are common during pregnancy or breast-feeding and could increase skin sensitivity and the risk of skin injury.

• DO NOT against any material other than skin.

• DO NOT use i-LIGHT® for any purpose other than hair removal.

• DO NOT treat any area where you may someday want your hair to grow back. The results may be permanent and irreversible.

, as this may result in undesired hair re-growth.

• DO NOT use on the face if you have a history of cold sores; use of IPL or any treatment that irritates skin can cause a recurrence of cold sores.

• If you’ve had professional or clinical or self-administered laser or IPL or electrolysis hair removal treatments, wait at least 6 months before using i-LIGHT®. If you’ve waxed, plucked or epilated hair in the treatment area, wait at least 6 weeks before using i-LIGHT® . The device uses the hair under your skin to

9

10

• DO NOT use directly over or near Active Implantable Medical Devices such as implantable pacemaker, have been reported during clinical studies, it is recommended to observe all active implantable medical device warnings regarding the use of electronic devices to prevent any failure or interruption of an active implantable device.

• Do not use over or near anything such as silicon implants, Implanon contraceptive implants, pacemakers, subcutaneous injection ports (insulin dispenser) or piercings.

• Wireless communications equipment may away.

• Do not use over or near

the i-LIGHT® device and should be kept at least 3.3 m

or dental implants.



PREPARING FOR USE

, Familiarise yourself with the features of your new i-LIGHT® device.

, Flash Window with built-in UV skin protection

• WARNING: always inspect the Flash Window before use to ensure there is no damage to the lens.

• WARNING: always clean the Flash Window before use with the lint-free cloth provided to ensure there is no oil or debris on the lens.

, Skin Contact Sensors

• This safety mechanism prevents accidental flashing. The device will not flash unless both Skin Contact

Sensors are in full contact with the skin.

, Flash Button

• The Flash Button is located on the hand piece. This is used to activate a flash.

, Skin Tone Sensor

• Will only allow usage on suitable skin tones.

, Attachments:

• Body attachment for large areas below the neck.

• Facial attachment for female facial use below the cheekbone.

Body Attachment

Facial Attachment

11

, Attachment Release Buttons

• Press both buttons and gently pull to remove the attachment.

, PREPARE THE i-LIGHT® FOR USE

• Unwrap the hand piece cord from the i-LIGHT® base and rest the hand piece back on the base unit.

• Ensure the power switch on the base unit is OFF.

• Connect the power cord to the i-LIGHT® base unit at the power inlet.

• Connect the power cord to the wall outlet. Turn the power switch ON. (fig. 5)

Fig. 5

, CHECK YOUR SKIN TONE

• Consult the skin and hair chart at the front of this manual to ensure your skin is in the suitable range and your hair colour is susceptible to treatment with i-LIGHT®.

• Place the skin of your intended treatment area onto the skin sensor – ensure the skin is touching the sensor. (Fig. 4)

• If your skin is suitable, you will hear a ‘beep’ and the i-LIGHT® will switch on.

• If your skin is unsuitable, you will hear a ‘buzz’ and the i-LIGHT® will remain switched off.

, NOTE: You must use the skin sensor on each body part you wish to treat.

Fig. 4

, SELECTING THE ENERGY LEVEL

• The i-LIGHT® is equipped with 5 energy levels. Level 1 is the lowest setting and level 5 is the highest setting.

, TIP: For the most effective results, always use the highest energy level that does not cause discomfort on the skin.

• To determine the energy level being used, observe the number of lights illuminated on the Energy

Level Display (fig. 6).

Fig. 6

, PREPARE YOUR SKIN FOR TREATMENT

• Ensure the area to be treated is clean and free from oils, deodorants, perfume, make up, lotions and creams. Shave the hair from the area to be treated, and ensure the skin is clean and dry.

• For facial use, you may prefer to trim the hair. If trimming; the hair must be trimmed to less than

0.5mm.

• Never use wax, epilation, tweezers or other methods that remove the hair from the root as IPL is not effective if the hair has been pulled out.

12

• Your i-LIGHT® will automatically be set to Energy Level 1 each time the device is powered ON. To change the level, press the Energy Level Selection Button.

, TEST THE i-LIGHT® ON YOUR SKIN

, Before your first full treatment, test the i-LIGHT® on a small patch of skin and wait 24 hours to

ensure there are no adverse reactions.

• Start at energy level 1.

1 Place the i-LIGHT® hand piece against your skin so the Flash Window is flush with the skin surface.

2 Ensure the Skin Contact Sensors are fully engaged and the Bulb Status Indicator Display is illuminated green (Fig. 7).

, PREPARE THE i-LIGHT® FOR USE

• Unwrap the hand piece cord from the i-LIGHT® base and rest the hand piece back on the base unit.

• Ensure the power switch on the base unit is OFF.

• Connect the power cord to the i-LIGHT® base unit at the power inlet.

• Connect the power cord to the wall outlet. Turn the power switch ON. (fig. 5)

Fig. 5

, SELECTING THE ENERGY LEVEL

• The i-LIGHT® is equipped with 5 energy levels. Level 1 is the lowest setting and level 5 is the highest setting.

, TIP: For the most effective results, always use the highest energy level that does not cause discomfort on the skin.

• To determine the energy level being used, observe the number of lights illuminated on the Energy

Level Display (fig. 6).

Fig. 6

• Your i-LIGHT® will automatically be set to Energy Level 1 each time the device is powered ON. To change the level, press the Energy Level Selection Button.

, TEST THE i-LIGHT® ON YOUR SKIN

, Before your first full treatment, test the i-LIGHT® on a small patch of skin and wait 24 hours to

ensure there are no adverse reactions.

• Start at energy level 1.

1 Place the i-LIGHT® hand piece against your skin so the Flash Window is flush with the skin surface.

2 Ensure the Skin Contact Sensors are fully engaged and the Bulb Status Indicator Display is illuminated green (Fig. 7).

13

Fig. 7

Fig. 9

3 Press the Flash Button to deliver a flash.

• Mild to moderate discomfort is normal. If a flash delivered at Energy Level 1 feels tolerable, increase to

Energy Level 2. Move the device to a different spot and flash the i-LIGHT® one more time. Repeat this process until you find the setting that feels right for you.

• Wait 24 hours and then look at the test area. If the skin appears normal, proceed with your first full treatment at the energy level you determined is right for you.

, NOTE: You must test the device on each area of the face or body you wish to treat.



TREATMENT

, CHANGING ATTACHMENTS

• Your i-LIGHT® comes with two separate attachments for the face and body.

• The Body Attachment is specially designed for body hair and can flash every 3 seconds.

• The Facial Attachment is specially tuned for Female Facial Hair and minimises light leakage, it can flash every 4 seconds.

• The attachments are marked with different icons to identify them (Fig. 8)

Fig. 8

, To change attachments:

, WARNING: Always ensure the unit is OFF and the power cord is disconnected before removing the attachment.

• If the attachment is removed while the unit is powered ON, all indicator lights on the base unit will flash and audible “beeps” will sound.

• Allow the system to cool down for 5 minutes before attempting to change attachments.

1 Turn the Power Switch OFF and unplug the Power Cord from the electrical outlet.

2 Hold the attachment with one hand while pressing both Attachment Release Buttons with the other hand and pull gently (Fig. 9).

3 Gently push the other attachment back into the Hand Piece making sure both side tabs click into place.

, NOTE: the longer tab (with gold circuits) must be on top to properly fit.

14

• Store the unused attachment in a safe location (such as in the packaging) taking care not to damage the Flash Window and other components.

• The i-LIGHT® is equipped with two operating modes: Single Flash Mode and Multi-Flash Mode.

Your i-LIGHT® device will automatically be set to Single Flash Mode each time the device is powered ON.

• Single Flash Mode: The i-LIGHT® will time precision treatments of the face and small areas.

• Multi-Flash Mode: The i-LIGHT® device will when the Flash Button is pressed and will continue to

•

, How to treat:

, NOTE: When the Skin Contact Sensors are fully engaged you will hear a ‘chirp’ and the Bulb Status

Indicator Display will illuminate green.

2

3 Move to the next area and treat in a grid like pattern to ensure full coverage of the treatment area.

• For Single-Flash Mode, press the Flash Button each time you move to the next area.

• For Multi-Flash Mode, keep your on the Flash Button to keep it depressed and glide to the next automatically after 3 seconds.

, NOTE: During Multi-Flash Mode if you let go of the Flash Button or lose skin contact, simply resume treatment by repeating the above steps.

Fig. 10

•

, Facial Treatment (female use only) sensitive and more likely to be exposed to the sun’s UV rays; therefore treating unwanted facial hair is the

Warnings and Safety Precautions carefully before beginning a facial treatment.

, IMPORTANT: The Facial Attachment has been specially designed to treat the unique characteristics of female facial hair. DO NOT use the Body Attachment on the face.

See section ‘Changing Attachments’ for more information.

Fig. 9

• Store the unused attachment in a safe location (such as in the packaging) taking care not to damage the Flash Window and other components.

• The i-LIGHT® is equipped with two operating modes: Single Flash Mode and Multi-Flash Mode.

Your i-LIGHT® device will automatically be set to Single Flash Mode each time the device is powered ON.

• Single Flash Mode: The i-LIGHT® will time precision treatments of the face and small areas.

• Multi-Flash Mode: The i-LIGHT® device will when the Flash Button is pressed and will continue to

•

, How to treat:

, NOTE: When the Skin Contact Sensors are fully engaged you will hear a ‘chirp’ and the Bulb Status

Indicator Display will illuminate green.

2

3 Move to the next area and treat in a grid like pattern to ensure full coverage of the treatment area.

• For Single-Flash Mode, press the Flash Button each time you move to the next area.

• For Multi-Flash Mode, keep your on the Flash Button to keep it depressed and glide to the next automatically after 3 seconds.

, NOTE: During Multi-Flash Mode if you let go of the Flash Button or lose skin contact, simply resume treatment by repeating the above steps.

Fig. 10

•

, Facial Treatment (female use only) sensitive and more likely to be exposed to the sun’s UV rays; therefore treating unwanted facial hair is the

Warnings and Safety Precautions carefully before beginning a facial treatment.

, IMPORTANT: The Facial Attachment has been specially designed to treat the unique characteristics of female facial hair. DO NOT use the Body Attachment on the face.

See section ‘Changing Attachments’ for more information.

15

16

• The Facial Attachment is only intended for use on female facial hair below the cheekbone (Fig. 10).

• DO NOT use on male beards or facial hair as the results may be permanent or uneven which may produce changes in facial hair characteristics which may not be desirable.



TREATMENT TIPS

,

Body Treatment

• necessary to suppress hair growth. It also ensures that you get the maximum use of the Bulb.

• For the most results, always use the highest intensity level that does not cause discomfort on the skin. The level you use should feel warm on your skin, but should never cause discomfort.

• You may notice that bony areas, such as elbows, shins and ankles, are more sensitive during treatment.

• This is normal and should not be cause for alarm. To avoid this sensitivity, try stretching the skin away from the bony area during treatment.

, Facial Treatment

• Test on a Patch of Skin – since facial skin tends to be more sensitive, make sure you test on a small patch before proceeding. See section ‘Test the i-LIGHT® on your skin’ for more details.

• Use a Mirror to Guide your Treatments – using a mirror for a good view of the area to be treated and to

• Stretch Skin for Better Skin Contact – the contours of the skin may make it your teeth or use your tongue to stretch your cheeks for better skin contact.

for the skin contact



POST-TREATMENT CARE

After treatment, you may experience slight redness or a warm sensation on your skin. This is normal and will disappear quickly. To avoid irritation to your skin after a treatment, take the following precautions:

• Avoid sun exposure for 24 hours after a treatment. Protect the skin with SPF 30 for 2 weeks after each treatment.

• Do not prolong sun exposure such as sunbathing, using a tanning bed, or self-tan for at least 2 weeks after the last treatment.

• After treatment, keep the area clean and dry and drink plenty of water to keep skin hydrated.

• Do not take hot baths, showers, or use steam rooms and saunas for 24 hours after treatment.

• Do not take part in contact sports for 24 hours after treatment.

• Do not depilate (waxing, plucking, threading or creams) during the treatment – shaving is acceptable as long as you avoid shaving 24 hours after each treatment.

• Do not use bleaching creams or perfumed products for 24 hours after treatment.



INFINITY BULB

•

• The bulb in this device is guaranteed to last for the entire warranty period as

communicated on the warranty details at the rear of this manual.

• In the extremely unlikely event that your bulb becomes empty, please contact your local Remington Service centre who will provide you with a replacement.

, Signs that the bulb needs replacing:

• Bulb Status Indicator is illuminated yellow: 150 Flashes remain in the bulb

• Bulb status indicator is yellow: Bulb is empty.

IN

FINITY



CLEANING YOUR i-LIGHT® DEVICE

CAUTION: Before cleaning your i-LIGHT®, make sure that the device is switched OFF and the power cord is disconnected from the device.

• Regular cleaning helps to ensure optimal results and a long life for the i-LIGHT® device.

• To clean the Flash Window, use only the lint-free cloth included with your i-LIGHT® device. Take care

• For stubborn stains on the window, dampen a cotton swab with surgical spirit or rubbing alcohol,

Use a small hand-held vacuum to remove dust and debris from the hand piece vents.

glass or the metallic surface inside the Treatment Head.

CAUTION: The i-LIGHT® is a high voltage device. Never immerse in water. Never clean the unit or any of its parts under a tap or in a dishwasher.

, Storage

• Switch the unit, unplug and allow to cool for 10 minutes before storage.

• Store the unit in a dry place at a temperature between 15º C and 35º C

TROUBLESHOOTING

• Always read these instructions fully before using i-LIGHT®

• Refer to this troubleshooting guide if you experience any problems with i-LIGHT®, as this section addresses the most common problems you could encounter with i-LIGHT®. If you have followed the instructions in this section and continue to experience problems, please contact the Remington®

Service Centre for further assistance.

, The power switch is ON, but the unit is not working.

• Make sure the unit is plugged into a working electrical outlet.

• Try switching to a different outlet.



INFINITY BULB

•

• The bulb in this device is guaranteed to last for the entire warranty period as

communicated on the warranty details at the rear of this manual.

• In the extremely unlikely event that your bulb becomes empty, please contact your local Remington Service centre who will provide you with a replacement.

, Signs that the bulb needs replacing:

• Bulb Status Indicator is illuminated yellow: 150 Flashes remain in the bulb

• Bulb status indicator is yellow: Bulb is empty.

IN

FINITY



CLEANING YOUR i-LIGHT® DEVICE

CAUTION: Before cleaning your i-LIGHT®, make sure that the device is switched OFF and the power cord is disconnected from the device.

• Regular cleaning helps to ensure optimal results and a long life for the i-LIGHT® device.

• To clean the Flash Window, use only the lint-free cloth included with your i-LIGHT® device. Take care

• For stubborn stains on the window, dampen a cotton swab with surgical spirit or rubbing alcohol,

Use a small hand-held vacuum to remove dust and debris from the hand piece vents.

glass or the metallic surface inside the Treatment Head.

CAUTION: The i-LIGHT® is a high voltage device. Never immerse in water. Never clean the unit or any of its parts under a tap or in a dishwasher.

, Storage

• Switch the unit, unplug and allow to cool for 10 minutes before storage.

• Store the unit in a dry place at a temperature between 15º C and 35º C

TROUBLESHOOTING

• Always read these instructions fully before using i-LIGHT®

• Refer to this troubleshooting guide if you experience any problems with i-LIGHT®, as this section addresses the most common problems you could encounter with i-LIGHT®. If you have followed the instructions in this section and continue to experience problems, please contact the Remington®

Service Centre for further assistance.

, The power switch is ON, but the unit is not working.

• Make sure the unit is plugged into a working electrical outlet.

• Try switching to a different outlet.

17

18

, The unit appears to have cracks or is broken.

• Do not use if the unit is damaged. If you have concerns about using the unit, discontinue use and contact the Remington® Service Centre for further assistance.

, I have switched the unit ON, but I cannot increase or decrease the energy level.

• Try resetting the unit by turning it off and waiting several seconds before turning it back on.

, The Bulb Status Indicator Light turns green but the unit does not flash when the button is pressed.

• Make sure the Skin Contact Sensor is in full contact with the skin.

• Try resetting the unit by turning it off and waiting several seconds before turning it back on.

, There is a strange smell.

• Be sure the area is completely shaved before treatment.

, The treated areas become red after treatment.

• This is normal and the redness should subside. If not, try using a lower energy level.

, BE AWARE: If the unit is used over an extended period of time, the unit might automatically disable momentarily (estimated 40 seconds) to cool down. Once the unit has cooled down, it will be ready to use again.

All currently selected energy level Unit is overheated and is disabled momentarily to cool down.

LED’s

All energy level indicators beep

Unit is malfunctioning. Turn the try again. If problem persists, the unit should be returned for repair.

Treatment head is removed or loose.

SOUNDS

Not full contact.

Replace bulb.

Skin contact sensors stuck.

Flash button was pressed while the skin contact sensor was not fully engaged.

Bulb is missing or needs to be replaced.

Flash button was pressed after the skin contact sensor had been engaged since unit start up. Skin contact sensor may be stuck.

FREQUENTLY ASKED QUESTIONS

Q. What areas of my body can I treat with i-LIGHT®?

A. i-LIGHT® is designed for unisex use on areas below the neck, including the legs, underarms, bikini line, arms, chest and back. Females can also use on facial hair below the cheekbone.

Q. What are the risks involved with i-LIGHT®. Is it safe?

A. read and follow the operating instructions and safety warnings.

Q. Is IPL dangerous for the skin after long term use?

A. light (IPL)

Q. Why is my hair growing despite treatments?

A. Results aren’t immediate, and individual results vary. Most users will begin to notice fewer hairs within

1-2 weeks after beginning treatment. During this time it may look like the hair is still growing, but it is actually being ‘pushed out’. phase are susceptible to treatment, which is why multiple treatments are required for optimal result.

Another reason for continued growth could be that the area was missed during a treatment. Repeat the treatment regime when you notice regrowth.

i-LIGHT® after recent sun exposure?

A. Sun exposure causes high levels of melanin to be present and exposes the skin to higher risk of burns or blisters following treatment.

SOUNDS

Not full contact.

Replace bulb.

Skin contact sensors stuck.

Flash button was pressed while the skin contact sensor was not fully engaged.

Bulb is missing or needs to be replaced.

Flash button was pressed after the skin contact sensor had been engaged since unit start up. Skin contact sensor may be stuck.

FREQUENTLY ASKED QUESTIONS

Q. What areas of my body can I treat with i-LIGHT®?

A. i-LIGHT® is designed for unisex use on areas below the neck, including the legs, underarms, bikini line, arms, chest and back. Females can also use on facial hair below the cheekbone.

Q. What are the risks involved with i-LIGHT®. Is it safe?

A. read and follow the operating instructions and safety warnings.

Q. Is IPL dangerous for the skin after long term use?

A. light (IPL)

Q. Why is my hair growing despite treatments?

A. Results aren’t immediate, and individual results vary. Most users will begin to notice fewer hairs within

1-2 weeks after beginning treatment. During this time it may look like the hair is still growing, but it is actually being ‘pushed out’. phase are susceptible to treatment, which is why multiple treatments are required for optimal result.

Another reason for continued growth could be that the area was missed during a treatment. Repeat the treatment regime when you notice regrowth.

i-LIGHT® after recent sun exposure?

A. Sun exposure causes high levels of melanin to be present and exposes the skin to higher risk of burns or blisters following treatment.

19

20

Q. Do I need eye protection while using i-LIGHT®?

A. No, it is not harmful to the eyes. i-LIGHT® features a safety system which prevents unintentional

ENVIRONMENTAL PROTECTION

To avoid environmental and health problems due to hazardous substances in electrical and electronic goods, appliances marked with this symbol must not be disposed of with unsorted municipal waste, but recovered, reused or recycled.

SERVICE AND GUARANTEE

Defects affecting product functionality appearing within the guarantee period will be corrected by replacement or repair at our option provided the product is used and maintained in accordance with the instructions.

Defects from repair by an unauthorised dealer are not covered.

Consumables are excluded.

Your statutory rights are not affected

If you call the Service Centre, please have the Model No. to hand, as we won’t be able to help you without it. The Model No. can be found on the rating plate of the appliance.

Replacement parts and accessories are available to buy through your Remington® Service Centre.

Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Limited

WARRANTY AGAINST DEFECTS

In this warranty:

Australian Consumer Law means the Australian consumer law set out in Schedule 2 to the Competition and Consumer Act 2010;

CGA means the New Zealand Consumer Guarantees Act 1993;

Goods means the product or equipment which was accompanied by this warranty and purchased in Australia or New Zealand, as the case may be;

Manufacturer, We or us means:

1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd

ACN, 007 070 573; or

2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited, as the case may be, contact details as set out at the end of this warranty;

Supplier means the authorised distributor or retailer of the Goods that sold you the Goods in Australia or in New Zealand; and

You means you, the original end-user purchaser of the Goods.

1. Our goods come with guarantees that cannot be excluded under the Australian

Consumer Law, or the CGA. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

2. The benefits provided by this Warranty are in addition to all other rights and remedies in respect of the Goods which the consumer has under either the Australian Consumer Law or the CGA. The original purchaser of the Goods is provided with the following Warranty subject to the Warranty Conditions:

3. We warrant the Goods for all parts defective in workmanship or materials for the period of t wo (2) years from the date of purchase (Warranty Period). If the Goods prove defective within the Warranty Period by reason of improper workmanship or material, we may, at our own discretion, repair or replace the Goods without charge.

Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Limited

WARRANTY AGAINST DEFECTS

In this warranty:

Australian Consumer Law means the Australian consumer law set out in Schedule 2 to the Competition and Consumer Act 2010;

CGA means the New Zealand Consumer Guarantees Act 1993;

Goods means the product or equipment which was accompanied by this warranty and purchased in Australia or New Zealand, as the case may be;

Manufacturer, We or us means:

1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd

ACN, 007 070 573; or

2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited, as the case may be, contact details as set out at the end of this warranty;

Supplier means the authorised distributor or retailer of the Goods that sold you the Goods in Australia or in New Zealand; and

You means you, the original end-user purchaser of the Goods.

1. Our goods come with guarantees that cannot be excluded under the Australian

Consumer Law, or the CGA. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

2. The benefits provided by this Warranty are in addition to all other rights and remedies in respect of the Goods which the consumer has under either the Australian Consumer Law or the CGA. The original purchaser of the Goods is provided with the following Warranty subject to the Warranty Conditions:

3. We warrant the Goods for all parts defective in workmanship or materials for the period of t wo (2) years from the date of purchase (Warranty Period). If the Goods prove defective within the Warranty Period by reason of improper workmanship or material, we may, at our own discretion, repair or replace the Goods without charge.

21

22

Warranty Conditions

4. The Goods must be used in accordance with the manufacturer’s instructions. This

Warranty does not apply should the defect in or failure of the Goods be attributable to misuse, abuse, accident or non-observance of manufacturer’s instructions on the part of the user. As far as the law permits, the manufacturer does not accept liability for any direct or consequential loss, damage or other expense caused by or arising out of any failure to use the Goods in accordance with the manufacturer’s instructions.

5. Exhaustible components (such as shaver heads, cutters and foils) of the Goods are included under this Warranty only where there is a defect in workmanship or materials used.

6. The warranty granted under clause 3 is limited to repair or replacement only.

7. Any parts of the Goods replaced during repairs or any product replaced remain the property of the manufacturer. In the event of the Goods being replaced during the

Warranty Period, the warranty on the replacement Goods will expire on the same date as for the Warranty Period on the original Goods which are replaced.

8. In order to claim under the warranty granted under clause 3 you must:

(a) Retain this warranty with your receipt/proof of purchase; and

(b) Return the Goods to us at the relevant address below or to the Supplier by prepaid freight within the Warranty Period accompanied with (i) the legible and unmodified original proof of purchase, which clearly indicates the name and address of the

Supplier, the date and place of purchase, the product name or other product serial number and (ii) this warranty.

9. This warranty is immediately void if:

(a) Any serial number or appliance plate is removed or defaced;

(b) The Goods have been serviced or otherwise repaired by a person not authorised to do so by us or where non approved replaced parts are used.

10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to any industrial or commercial use of the Goods. The Goods must be connected to the electrical voltage requirements as specified in the ratings label located on the Goods.

11. This warranty does not cover the cost of claiming under the warranty or transport of the

Goods to and from the Supplier or us.

12. This warranty is only valid and enforceable in Australia against Spectrum Brands

Australia Pty Ltd and in New Zealand against Spectrum Brands New Zealand Limited.

Contact us or the Supplier for further details.

Spectrum Brands Australia Pty Ltd

Locked Bag 3004

Braeside, VIC 3195

Australia

Customer service in Australia: 1800 623 118

E-mail: [email protected]

Website: www.remington-products.com.au

Spectrum Brands New Zealand Limited

PO Box 9817

Newmarket, Auckland 1149

New Zealand

Customer service in New Zealand: 0800 736 776

E-mail: [email protected]

Website: www.remington-products.com.au

Money Back Offer

Australia/New Zealand Only

If within 90 days you are not fully satisfied with your Remington

®

i-LIGHT

®

Pro+ Face & Body, please call your local Remington Customer

Service Centre:

Australia: 1800 623 118

New Zealand: 0800 736 776

REMINGTON SERVICE HOTLINE

Australia 1800 623 118 (toll free)

New Zealand 0800 736 776 (toll free)

AUTHORISED REPAIR CENTRES

Visit www.remington-products.com.au for Authorised repair centre details.

Remington

®

and i-LIGHT

®

are registered trademarks of Spectrum Brands, Inc., or one of its subsidiaries.

Made in China to the specifications of Spectrum Brands, Inc.

© 2015 Spectrum Brands, Inc

Rev 08/15

Part No. T22-0003384