Always there to help you
Register your product and get support at
www.philips.com/welcome
CED1900BT
Question?
Contact
Philips
User manual
3
Manuale utente
77
Gebruiksaanwijzing
25
Gebruiksaanwijzing
103
Moded’emploi
51
Instrukcjaobsługi
129
Contents
1Safety
2 Your car entertainment system
Introduction
What's in the box
3 Install the car entertainment system
Connect wires
Mount into the dashboard
4 Get started
Prepare the remote control
Turn on
Use the home menu
Set the date and time
5 Play from hard media
Load a disc
Connect a USB storage device
Insert an SD/SDHC card
Control play
Browse recorded files
6 Listen to radio
Switch to radio mode
Set up
Tune to a radio station
Store radio stations in memory
Tune to a preset radio station
7 Use the navigation system
Insert the map data card
Navigate your road trip
8 Use Bluetooth devices
Activate the Bluetooth function
Pair a device
Play audio from a connected device
Make a call
2
2
2
3
9 Play from an iPod/iPhone
Connect your iPod/iPhone
Control play
Charge your iPod/iPhone
3
3
7
10 Adjust sound
8
8
8
9
9
11Others
10
10
10
10
11
12
12
12
12
13
13
13
17
17
17
18
18
Compatible iPod/iPhone models
18
18
18
Adjust the volume level
Mute sound
18
18
19
19
20
20
Play external audio/video input
Use rear monitors
Use buttons on the steering wheel
Set the rear view camera
Reset the system
12 Product information
20
13Troubleshooting
22
22
22
General
About the Bluetooth device
14Notice
23
23
23
23
24
Compliance
Care of the environment
Trademark notice
Copyright
14
14
14
14
14
14
16
16
EN
1
English
Contents
1Safety
•
Risk of swallowing coin battery!
•
battery, which can potentially be swallowed. Keep
Read and understand all instructions before you use the
device. If damage is caused by failure to follow instructions,
the warranty does not apply.
•
the battery out of reach of children at all times! If
swallowed, the battery can cause serious injury or
Use of controls or adjustments or performance of
death. Severe internal burns can occur within two
procedures other than herein may result in hazardous
hours of ingestion.
radiation exposure or other unsafe operation.
•
•
The device is designed for negative ground (earth) 12 V
immediate medical attention.
To reduce the risk of traffic accidents, do not watch
•
video when driving.
•
Make sure that the battery compartment is
completely secure after you replace the battery.
Improper fuses can cause damage or fire. When you
•
need to change the fuse, consult a professional.
•
If the battery compartment cannot be completely
secured, discontinue use of the product. Keep out
Use only the supplied mounting hardware for a safe
of reach of children and contact the manufacturer.
and secure installation.
•
When you change the batteries, always keep all
new and used batteries out of reach of children.
To ensure safe driving, adjust the volume to a safe and
comfortable level.
•
If you suspect that a battery has been swallowed
or placed inside any part of the body, seek
DC operation only.
•
The device may contain a coin/button type
To avoid short circuits, do not expose the device,
remote control or remote control batteries to rain or
water.
•
The device shall not be exposed to dripping or
2
splashing.
•
Do not place any sources of danger on the device (e.g.
liquid filled objects, lighted candles).
•
Never insert objects into the ventilation slots or other
openings on the device.
•
Never place any objects other than discs into the disc
tray/slot.
•
To avoid exposure to laser radiation, do not
disassemble the device.
•
Risk of damage to the screen! Never push, rub, or strike
the screen with any object.
•
Never use solvents such as benzene, thinner, cleaners
available commercially, or anti-static sprays intended
for discs.
•
Clean the device with soft, damp cloth. Never use
substances such as alcohol, chemicals or household
cleaners on the device.
2
EN
Your car entertainment
system
Congratulations on your purchase, and welcome to Philips! To
fully benefit from the support that Philips offers, register your
product at www.philips.com/welcome.
Introduction
With the car entertainment system, you can
•
•
•
•
•
•
listen to music,
watch videos,
view pictures,
listen to FM (RDS included) and AM/MW radio,
make phone calls via Bluetooth, and
navigate your road trip.
What's in the box
•• This system is designed for negative ground (earth) 12V
Check and identify the contents of the package:
a
b
c
d
e
f
g
h
DC operation only.
•• Always install this system in the car dashboard. Other
1
Main unit (with a sleeve)
2
Remote
control
3
Trim plate
4
Rubber
cushion
5
Screw X 4 (M5x8mm)
6
Hexagon
head screw
7
Remote control battery
8
User manual
locations can be dangerous as the rear of the system
heats up during use.
•• To avoid short-circuit: before you connect, make sure
that the ignition is off.
•• Make sure that you connect the yellow and red power
supply leads after all other leads are connected.
•• Make sure that all loose leads are insulated with
electrical tape.
•• Make sure that the leads do not get caught under
screws iron parts that will move (e.g. seat rail).
•• Make sure that all ground (earth) leads are run to a
common ground (earth) point.
•• Use only the supplied mounting hardware for a safe
and secure installation.
•• Improper fuses can cause damage or fire. When you
need to change the fuse, consult a professional.
•• When you connect other devices to this system, make
sure that the rating of the car circuit is higher than the
total fuse value of all the connected devices.
•• Never connect speaker wires to the metal body or
chassis of the car.
•• Never connect speaker wires with stripes to one
another.
Connect wires
Note
•• The ISO male connectors are not supplied.
•• Make sure that all loose leads are insulated with
electrical tape.
3
Install the car
entertainment system
•• Consult a professional to connect wires as instructed
below.
•• Before connection, check the car's wiring carefully.
1
Connect the ISO male connectors.
Always follow the instructions in this chapter in sequence.
These instructions are for a typical installation. However, if
your car has different requirements, make the adjustment
accordingly. If you have any question regarding installation kits,
consult your local retailer.
EN
3
English
Note
ISO male
connectors
Connect to
Connectors and
sockets on rear panel
External sockets or
connectors
Green strip, black-edged
green strip
Rear left speaker
1
For ISO male connectors
As indicated above
2
REAR OUT L (White
socket)
b
White strip, black-edged
white strip
Front left speaker
Rear left speaker
c
Gray strip, black-edged
gray strip
Front right speaker
3
REAR OUT R (Red socket)
Rear right speaker
4
Front right speaker
Rear right speaker
FRONT OUT R
(Red socket)
d
Purple strip, black-edged
purple strip
5
Front left speaker
Red strip
Ignition key +12V DC
when ON/ACC
FRONT OUT L
(White socket)
e
6
f
Blue strip
Motor/electric antenna
relay control lead
VIDEO OUT 1
(Yellow socket)
Video input socket
of an external display
device
g
White-edged blue strip
Amplifier relay control
lead
7
VIDEO OUT 2
(Yellow socket)
Video input socket
of an external display
device
Video output socket of
an external player
a
h
Black strip
Ground
8
VIDEO IN (Yellow socket)
i
Yellow strip
The +12V car battery
which is energized at
all times
9
CAMERA IN (Purple socket) Video output socket of
an external camera
10
SUB-W OUT (Blue socket)
Sub-woofer
11
AV-IN L (White socket)
Left audio channel
output socket of an
external player
12
AV-IN R (Red socket)
Right audio channel
output socket of an
external player
13
REVERSE CAMERA
(Purple wire)
Reverse camera (B+)
14
PARKING BRAKE
(Pink wire)
Parking brake (-)
15
OE SWC IR REMOTE IN
(Brown wire)
OE SWC remote in
16
OE SWC IR REMOTE IN
(Black wire)
Ground
17
OE SWC AD LEARN
(White wire)
OE SWC AD Learn
line 1
18
OE SWC AD LEARN
(White wire)
OE SWC AD Learn
line 2
19
OE SWC AD LEARN
(Black wire)
Ground
20
External Mic
(Black connector)
External microphone
21
EXTERNAL BOX
CONNECTOR
(Black connector)
External navigation box
22
GPS AERIAL
(Black connector)
GPS smart antenna
23
RADIO ANTENNA
(Black connector)
Radio antenna
2
Connect other wires if necessary.
Caution
•• To avoid an accident, the driver must not watch video
while driving. By design, this system disallows watching
video during drive. Park your car in a safe place and
engage the parking brake before watching video.
Note
•• When the parking brake of your vehicle is not engaged,
the video blocking system is activated. It blocks the
display of front video source only.
•• If the system is not properly connected with the
parking brake control module of your vehicle, video
signals will be blocked by the system, with the below
message displayed on the TFT.
4
EN
External sockets or
connectors
24
Rear Monitor Audio Out 1
(White connector)
Left audio channel
input socket of one
rear monitor
25
Rear Monitor Audio Out 1
(Red connector)
Right audio channel
input socket of one
rear monitor
26
Rear Monitor Audio Out 2
(White connector)
Left audio channel
input socket of another
rear monitor
27
Rear Monitor Audio Out
2 (Red connector)
Right audio channel
input socket of another
rear monitor
English
Connectors and
sockets on rear panel
Tip
•• The pin arrangement for the ISO connectors depends
on the type of your vehicle. To avoid damage to the
system, connect properly.
EN
5
s
r
z
q
y
p
x
o
w
v
n
u
m
t
a
b
6
EN
c d e
f
g h i j k l
3
Remove the mounting sleeve with the supplied
disassembly tools.
English
Mount into the dashboard
Note
•• Make sure that wires are correctly connected before
you mount the main unit into a car.
•• If preset radio stations are lost when the ignition key
is turned OFF and then back ON, reconnect the red
leads crosswise to the yellow ones.
1
If the car does not have an on-board drive or
navigation computer, disconnect the negative terminal
of the car battery.
•
4
Install the sleeve into the dashboard and bend the tabs
outward to fix the sleeve.
•
If you disconnect the car battery in a car that has
If the system is not fixed by sleeve but by the
supplied screws, skip this step.
an on-board drive or navigation computer, the
computer may lose its memory.
•
If the car battery is not disconnected, to avoid
short-circuit, make sure that bare wires do not
touch each other.
Make sure that the car dashboard opening is within
these measurements:
5
m
5m
182
•
Slide the unit into the dashboard until a click sound is
heard.
mm
112 mm
2
6
Attach the trim plate.
7
Reconnect the negative terminal of the car battery.
Since the unit cannot be used if the dashboard
opening's slant angle is above 20 degrees, make
sure that the horizontal slant of the car dashboard
opening is between 0 and 20 degrees.
EN
7
4
Get started
Caution
Turn on
Press
.
»» PHILIPS logo and a progress bar are displayed
while boot-up.
•• Risk of car accidents! Never watch video or operate
this system while driving.
•
To turn off the system, press and hold
for
3 seconds.
Prepare the remote control
For the first time use
For the fist time use
After successful boot-up, the following interface is displayed.
Pull the protective sheet out.
»» The remote control is ready for use.
Replace the battery
Caution
•• Risk of explosion! Keep batteries away from heat,
sunshine or fire. Never discard batteries in fire.
1
Tap to select a language for on-screen display.
»» The following interface is displayed.
Note
•• Remove the battery if it is exhausted or if the remote
control is not to be used for a long time.
•• Batteries contain chemical substances, they should be
disposed of properly.
•• Perchlorate Material - special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate.
2
Tap to select a radio region that matches your location.
»» The following interface is displayed.
3
Tap [Finish] to complete the initial setup.
»» The device switches to radio mode automatically.
1
2
3
8
Pull out the battery tray.
Insert one CR2025 battery with correct polarity (+/-)
as indicated.
Insert the battery tray.
EN
•
Use the home menu
English
external video player.
Note
•
is displayed when you touch an icon, it indicates
that the selected media or feature is unavailable at the
current time.
•
[Rear zone]: Access the settings for rear
[SWC]: Access the interface to assign
functions to buttons on the steering wheel.
•
Access the home menu
R
monitors.
•• If
Tap
[AV-IN 1]/[AV-IN 2]: Switch the source to the
audio and video input that is transferred from an
[Settings]: Access the system menu.
Set the date and time
to access the home menu.
»» The clock, date, and the bar for popular icons are
displayed.
1
2
Tap
>
to access the full menu with all feature
icons displayed.
Tap
[Settings].
»» The [General]menu is displayed.
•
To access the full menu with all feature icons displayed,
tap
•
.
To return to the home menu, tap
.
3
4
•
•
•
•
•
[24Hr]: 24-hour time format
[12Hr]: 12-hour time format
Tap [Date] to display the interface for setting the date.
[Radio]: Switch the source to FM/AM radio.
[Disc]: Switch the source to disc.
[USB]: Switch the source to USB storage
device.
•
Tap [Clock Mode] to select a time format.
5
6
Tap
7
8
Tap
to set the year, month, and date.
Tap [Time] to display the interface for setting the time.
[SDHC]: Switch the source to SD/SDHC
card.
•
: Once your iPod/iPhone is connected and
recognized, this icon is displayed in the bar of
favorite icons. Tap it to switch the source back to
iPod/iPhone.
•
•
[Navigation]: Access the navigation system.
[Bluetooth]: Use the Bluetooth feature.
Tap
to set the hour and minute.
to return to the home menu.
EN
9
5
Play from hard media
You can use this system to listen to audio, watch videos, and
view photos that are stored on a disc, USB storage device, or
SD/SDHC card.
Connect a USB storage device
Note
•• Make sure that the USB storage device contains
compatible files.
•• NTFS (New Technology File System) file system is not
Note
supported.
•• Before use, check for compatible media.
1
2
Load a disc
Push the USB socket cover upwards to open it.
Connect the USB storage device to the USB socket.
»» Play starts automatically.
Caution
•• Never insert any object other than a disc of 12-cm
diameter into the disc slot.
•
To remove the USB storage device, switch the
system to another source first.
1
Insert the disc into the disc slot with the label side
facing up.
»» Play starts automatically.
•
If play does not start automatically, tap the screen
to display the
2
icon, and then tap
to start
play.
To eject the disc, press
.
»» When the disc is ejected, the system switches to
the previous source or radio mode.
Insert an SD/SDHC card
Note
•• Make sure that the SD/SDHC card contains compatible
files.
•• NTFS (New Technology File System) file system is not
supported.
1
2
Flip up the protective cover.
Insert the SD/SDHC card into the
hear a "click".
slot until you
»» Play starts automatically.
Region Code
You can play DVD discs marked with the following region code.
DVD region code
Countries
Europe
Remove the SD/SDHC card
1
2
3
10
EN
Switch system to another source.
Press the card inwards until you hear a "click".
»» The card is disengaged.
Pull out the SD/SDHC card.
[16:9]/[4:3]: Select an aspect ratio.
: Tap to display the brightness bar, and then tap on
English
•
•
Control play
the bar to adjust the screen brightness.
Videos
•
: Tap to display the contrast bar, and then tap on
the bar to adjust the image contrast.
•
: Tap to display the saturation bar, and then tap on
the bar to adjust the image saturation.
•
: Display control icons on the first page.
Audios
•
•
•
•
•
: Return to the home menu.
: Zoom in or out of the image.
: Select an available audio channel or audio language.
: Select an available subtitle.
•
•
For DVD, return to the disc menu or root menu.
For recorded files, return to the list of files or
folders.
•
•
•
•
•
•
PBC: For VCD/SVCD only, enable or disable the PBC
(Playback Control) feature.
•
/
: Skip to the previous or next title,
chapter, track, or file.
•
To search forward fast or rewind the track, tap on
the progress bar.
•
•
/
: Start, pause, or resume play.
: Display control icons on the second page.
: Return to the home menu.
Press once to access the track list.
Press twice to access the folder list.
Press repeatedly to return to the playback
interface.
•
: For recorded files only, skip to the next audio
folder.
•
•
: Return to the list of tracks or folders.
/
•
: Skip to the previous or next track.
To search forward fast or rewind the track, tap on
the progress bar.
•
•
/
•
•
•
: Start, pause, or resume play.
/
/
: Select a repeat mode.
: Repeat the current track.
: For recorded files, repeat all tracks in the
current folder.
•
: Select a repeat mode.
DVD: [Repeat chapter] (repeat the current
chapter), [Repeat title] (repeat the current title),
[Repeat all] (repeat all chapters and titles), or
•
•
(highlighted): Repeat all tracks.
: Select random play (
sequential play (
highlighted) or
in gray).
[Repeat off] (cancel repeat play).
•
VCD/SVCD: [Repeat one] (repeat the current
track) or [Repeat all] (repeat all tracks).
•
Recorded files: [Repeat one] (repeat the current
video file), [Repeat folder] (repeat all video files in
the current folder), or [Repeat all] (repeat all video
files).
EN
11
2
Pictures
3
•
•
•
: Return to the home menu.
: Zoom in or out of the picture.
/
: Rotate the picture clockwise or anti-clockwise
by 90 degrees.
•
•
•
•
•
•
/
/
/
: Return to the list of files or folders.
: Select the previous or next picture.
: Pause or resume the slideshow.
: Tap to display the brightness bar, and then tap on
the bar to adjust the screen brightness.
•
: Tap to display the contrast bar, and then tap on
•
•
•
: Display the list of audio tracks or folders.
: Display the list of picture files or folders.
: Display the list of video files or folders.
Tap the name of a file to start play.
6
Listen to radio
Switch to radio mode
After the boot-up at the first time, the system switches to
radio mode automatically.
To switch the source back to radio afterwards, tap
[Radio] on the home menu.
»» The interface for radio is displayed.
: Display control icons on the second page.
[16:9]/[4:3]: Select an aspect ratio.
Tap an icon to select a file category.
Set up
Before you search for radio stations, make prior setup.
Tap
to display the setup menus.
the bar to adjust the image contrast.
•
: Tap to display the saturation bar, and tap on the
bar to adjust the image saturation.
•
: Display control icons on the first page.
Browse recorded files
During playing recorded files, you can access the file list and
select files from the list.
1
12
Tap
EN
to access the list of files or folders.
Select a radio range
1
Tap [Radio Range].
Tap [Distance] or [Local] to select a tuner sensitivity.
•
•
[Distance]: Stations with strong and weak signals
Store radio stations in memory
can be tuned to.
You can store up to 6 stations in each band.
[Local]: Only stations with strong signals can be
tuned to.
Enable the RDS feature
Note
Store radio stations manually
1
2
3
•• RDS feature is enabled by default.
•• Only after the RDS feature is enabled, the option of
Select a band.
Tune to the target radio station.
Tap and hold one of the channels (1 to 6) over two
seconds.
»» The radio station is saved under the selected
channel.
[PTY list] is displayed.
Tap [RDS Off] (RDS disabled) to enable the RDS feature.
»» The option of [PTY list]is displayed.
•
To disable the RDS feature, tap [RDS On] (RDS
enabled).
Tune to a radio station
English
2
Store radio stations automatically
You can search for a radio station with intro search, which
broadcasts a 10-second preview of each detected radio
station.
1
2
3
Select a band.
Tap
.
Tap [Auto Store].
»» Auto search starts. The six strongest stations of
the selected band are saved in preset channels
automatically.
Tune to a preset radio station
1
2
Tap FM or AM to select a band.
•
•
FM bands: FM1, FM2, FM3
AM bands: AM1, AM2
1
2
Select a band.
Tap one of the preset channels (1 to 6) to select a
preset radio station.
Tap
or
repeatedly until the frequency of target
radio station is displayed.
•
To tune to a radio station automatically, tap and
hold
or
until the frequency digits start
change.
Tip
•• You can also press BAND on the remote control
repeatedly to select a band.
EN
13
7
Use the navigation
system
Insert the map data card
Note
•• The map data card is not included in the packaging.
•• Before using the map data card, update the map data
8
Use Bluetooth devices
With this system, you can listen to audio from a player and
make a call through Bluetooth.
Activate the Bluetooth function
•
•
On the home menu, tap
In any other mode, tap
.
on top of the screen.
if necessary.
Pair a device
Note
•• Philips does not guarantee the compatibility with all
Bluetooth devices.
•• Before pairing a device with this system, read its user
manual for Bluetooth compatibility.
1
2
3
•• Make sure that Bluetooth function is enabled on your
Flip up the protective cover.
Insert the map data card into the MAP slot until you
hear a "click".
Close the protective cover.
Navigate your road trip
Note
•• Risk of traffic accident! Never operate the navigation
system during drive. Complete the setting of your
destination and other navigation specifications before
you drive.
1
device, and your device is set as visible to all other
Bluetooth devices.
•• The operational range between this system and a
Bluetooth device is approximately 8 meters (24 feet).
•• Any obstacle between this system and a Bluetooth
device can reduce the operational range.
•• Keep away from any other electronic device that may
cause interference.
Pair the first device
1
Activate the Bluetooth function on this system.
»» The following interface is displayed.
Press NAVI.
•
You can also tap
on the home menu to access
the navigation system.
»» The navigation interface is displayed in a few
2
14
seconds.
Follow the user manual of the navigation map to set
navigation specifications.
EN
2
Tap
on this system to search for other Bluetooth
devices.
In the device list, tap the name of your Bluetooth
behind the name.
device, and then tap
: Tap it to display the list of paired players.
: Tap it to display the on-screen keypad for
English
3
phone calls.
: Tap it to display the phone book that is
synchronized with your mobile phone and keypad.
: Tap it to display the list of favorite contacts.
Pair more devices
»» The paring starts, and then a pairing request from
4
1
Activate the Bluetooth function on this system.
»» One of the following interfaces is displayed.
CED1900 is displayed on your device.
On your device, accept the pairing request from
CED1900, enter the default password '0000', and then
confirm the password entry.
»» [Paired OK!] flashes, and then [Connecting] is
5
displayed on this system.
On your device, enable or permit the connection with
CED1900.
•
If a player is connected, the music playback
interface is displayed on this system.
2
Tap
3
4
Tap [New Pairing] to start searching for Bluetooth
devices.
on the top right corner.
: Tap it to return to the music playback
interface.
: Tap it to display the list of paired mobile
phones.
: Tap it to display the list of paired mobile
phones.
: Tap it to display the list of paired mobile
phones.
•
If a mobile phone is connected, the keypad is
displayed on this system.
Repeat steps 3 to 5 that are indicated in the above
section "Pair the first device" to complete the
connection.
Note
•• You can connect a music player and a mobile phone
simultaneously.
EN
15
Manage paired devices
1
2
3
1
2
Play a track on the connected device.
3
Tap icons on the interface to control play.
Activate the Bluetooth function.
Tap
•
•
or
to display the music playback
.
To manage paired players, tap
.
To manage paired mobile phones, tap
Tap
On this system, tap
interface.
.
on the top right corner.
•
•
: Pause or resume play.
/
: Select the previous or next
track.
4
Note
Tap [Paired Device].
»» The list of paired devices is displayed.
•• If the connected device does not support the AVRCP
profile, control play on the connected device.
Make a call
Note
5
Tap the name of the paired device that you want to
reconnect, disconnect, or delete.
•
•
•
6
: Tap to reconnect the device.
: Tap to disconnect the device.
: Tap to delete the device from the list of
paired devices.
Tap
,
, or
•• Keep the Bluetooth connection active between the
system and your mobile phone.
Call a number
You can make phone calls with the system.
1
Tap
on top of the screen.
»» The keypad is displayed.
.
•
Tip
If the keypad is not displayed, tap
.
•• If you want to manually reconnect a device after the
connection is interrupted, disable the function of
automatic connection.
Play audio from a connected device
If the connected Bluetooth device supports Advanced Audio
Distribution Profile (A2DP), you can listen to tracks that are
stored on the device through the system. If the device also
supports Audio Video Remote Control Profile (AVRCP)
profile, you can control play on the system or with its remote
control.
16
EN
2
Tap number icons to enter the phone number.
•
•
•
To clear the last digit, tap
To clear all digits, tap
.
.
To return to the previous screen, tap
.
Tap
•
•
9
to send the call.
To end the call, tap
.
To enter numbers during the call, tap
to
display the keypad first.
Note
Redial the last called number
1
2
Tap
•• During play, no audio signals are transferred through
the headphone socket of your iPod/iPhone.
.
»» The last called number is displayed.
Tap
Compatible iPod/iPhone models
again to send the call.
This system supports the following iPod and iPhone models.
Answer a call
Note
•• By default, all incoming calls are picked up automatically.
You can disable the function of automatic answer.
1
2
Play from an iPod/
iPhone
English
3
When there is an incoming call, [Incoming call…] is
displayed on the screen.
Tap
•
iPhone 4, iPhone 3GS, iPhone 3G, and iPhone
iPod touch (1st, 2nd, 3rd, and 4th generations)
iPod nano (1st, 2nd, 3rd, 4th, 5th, and 6th generations)
iPod classic
Connect your iPod/iPhone
Connect an Apple 30-pin USB cable to:
to answer the call.
To reject or end the call, tap
•
•
•
•
.
•
•
the USB socket on the front panel of this system, and
your iPod/iPhone.
»» The system starts playing tracks that are stored on
Transfer a phone call to mobile phone
your iPod/iPhone.
By default, the voice comes from the loudspeakers during a
call.
•
1
is displayed in the bar of popular icons on the
Tap
to transfer the phone call to your mobile
phone.
»» The loudspeakers are muted, and the voice comes
2
Once your iPod/iPhone is connected and recognized,
from the mobile phone only.
Take up your mobile phone for the conversation.
home menu. You can tap it to switch back to this
playback interface.
Note
•• Before you disconnect your iPod/iPhone, switch the
system to another source.
EN
17
10 Adjust sound
Control play
By default, use the on-screen playback interface of this system
to control play.
When you listen to radio, enjoy music, or watch video, follow
the instructions below to adjust sound.
•
•
•
Adjust the volume level
: Tap to pause play.
: Tap to resume play.
/
: Tap to play the previous or next
track.
•
/
•
•
•
•
: Tap to select a repeat mode.
•
(highlighted): Repeat all tracks.
(in gray): Cancel repeat play.
(highlighted): Play tracks randomly.
+: Increase the volume level.
-: Decrease the volume level.
Mute sound
Press
•
: Tap to switch to the iPod control mode, and then
on the front panel.
To release the speakers from mute status, press
again.
(in gray): Play tracks in sequence.
you can control play on your iPod/iPhone.
•
•
•
: Repeat the current track.
: Tap to select a play mode.
•
•
Press +/- repeatedly on the front panel.
11Others
: Tap to switch back to the on-screen control mode,
and then you can control play on this system.
•
: Tap to access the music menu.
Search for a track
Play external audio/video input
You can connect an external audio/video player to this
system.
You can select a track quickly through the music menu.
1
Tap
to access the music menu.
1
2
3
Tap to select a category.
»» Tracks under the selected category are listed.
Tap a track name to start play.
•
If one or more subcategories are under the
selected category, select a category first.
Charge your iPod/iPhone
Once the iPod/iPhone is connected and recognized, the iPod/
iPhone begins to charge.
2
3
4
Connect a composite AV cable to
•
•
the AV-IN socket on the front panel, and
the audio and video output sockets of the
external player.
Tap
>
to access the full menu with all feature
icons displayed.
Tap
[AV-IN 1] to display the playback interface.
Operate on the external player to start play (see the
user manual of the external device).
Tip
•• If you connect this system to an external player through
the VIDEO IN, AV-IN L, and AV-IN R sockets on the
rear panel, tap
instead of
18
EN
[AV-IN 2] to switch the source
[AV-IN 1].
4
5
If one or two monitors are connected for backseat
passengers, you can select different sources for front and
backseat passengers.
Tap to select an available source to start play.
Tap [Rear speaker] to enable or disable the audio
output to rear speakers.
•
•
English
Use rear monitors
[On]: Enable the audio output to rear speakers.
[Off]: Mute rear speakers.
Note
•• Make sure that rear monitors are correctly connected
to this system.
•• Only when the multi-zone display mode is activated,
rear monitors can receive signals from the system.
•• By default, the same signals are transferred to the front
and rear monitors.
•• When a disc, USB storage device, SD/SDHC card, or
iPod/iPhone connected through the USB socket is
selected as the source for front zone, you cannot select
another source for rear zone.
•• Only when the system is in radio mode, navigation mode,
or Bluetooth mode, you can select a source for rear zone
from disc, SD/SDHC card, USB storage device, or iPod/
iPhone connected through the USB socket.
1
2
6
R
to return to the previous mode.
Switch the control interfaces
When different sources are selected for front passengers and
backseat passengers, you can tap R to switch the control
interface for front source or rear source.
»» When
Tap
>
to access the full menu with all feature
icons displayed.
Tap
Tap
R
is solidly displayed, the current control
interface is for the front source.
»» When
.
R
blinks with
and [Rear zone]
displayed, the current control interface is for the
»» The [Rear zone] menu is displayed.
rear source.
Use buttons on the steering wheel
You can assign a function to a button on the steering wheel,
and then control the system with that button.
3
Tap [Mode] to enable or disable the signal transferring
to rear monitors.
•
•
[On]: Enable the signal transferring to rear monitors.
1
2
Tap
>
to access the full menu with all feature
icons displayed.
Tap
.
»» The [Steering Wheel Remote Control Learning]
interface is displayed.
[Off]: Disable the signal transferring to rear monitors.
»» When it is enabled, the following interface is
displayed.
EN
19
3
Tap an icon, for example,
, of which you want to
assign the function to a button on the steering wheel.
Reset the system
If the system hangs up, reset it.
4
•
To cancel the assignment, tap [Cancel].
Press and hold the button on the steering wheel for
one second.
1
2
Flip up the protective cover.
Press RESET with the tip of a ball-point pen or
toothpick.
»» The following interface is displayed.
12 Product information
Note
•• Product information is subject to change without prior
5
Repeat steps 3 and 4 to assign more functions to
buttons on the steering wheel.
•
To clear the assignment, tap [Clear all].
Set the rear view camera
If a rear view camera is connected, you can view on the
screen what the camera takes.
1
2
Tap
>
to access the full menu with all feature
icons displayed.
Tap
(the icon is displayed only when a compatible
camera is correctly connected).
»» Picture from rear camera is displayed.
notice.
General
Power supply
12 V DC (11 V - 16 V), negative
ground
Fuse
15 A
Suitable speaker
impedance
4-8
Maximum power output
45 W x 4 channels
Continuous power
output
EN
10%
Pre-Amp output voltage
4.0 V (CD play mode; 1 kHz, 0
load)
dB, 10 k
Sub-woofer output
voltage
4.0 V (CD play mode, 61 Hz, 0
load)
dB, 10 k
Aux-in level
20
24 W x 4 channels (4
T.H.D.)
800 mV
Dimensions
(W x H x D)
178 x 101.5 x 160 mm
Weight (main unit)
3.1 kg
USB playability information
System
DVD / CD audio / MP3
system
Disc diameter
12 cm
Frequency response
20 Hz - 20 kHz
Signal/noise ratio
> 75 dB
Total harmonic distortion
Less than 0.3%
•
•
•
•
Channel separation
> 55 dB
Supported USB formats:
Video signal format
NTSC/PAL
Video output
1 +/- 0.2 V p-p
•
•
•
•
•
•
•
•
Radio
Frequency range - FM
87.5 - 108.0 MHz
(50 kHz per step)
Frequency range - AM(MW)
522 - 1620 kHz
(9 kHz per step)
Usable sensitivity - FM
2 uV
Usable sensitivity - AM (MW)
25 uV
LCD
USB flash memory (USB 2.0 or USB1.1)
USB flash players (USB 2.0 or USB1.1)
Memory cards (SD/SDHC)
Maximum capacity: 32 G
USB or memory file format: FAT16, FAT32
MP3 bit rate (data rate): 32-320 Kbps and variable bit rate
WMA v9 or earlier
Directory nesting up to a maximum of 8 levels
Number of albums/folders: maximum 99
Number of tracks/titles: maximum 999
ID3 tag v2.0 or later
File name in Unicode UTF8 (maximum length: 128 bytes)
Supported MP3 disc format:
•
•
ISO9660, Joliet
Maximum title number: 512 (depending on file name
length)
Screen size
6.2 inches
Display resolution
800 x 480 dots
Contrast ratio
500
Brightness
450 cd/m²
•
•
•
Communication
system
Bluetooth Standard version 2.0
Output
Bluetooth Standard Power Class 2
Maximum
communication
range
Line of sight approx. 8m
Frequency band
2.4 GHz band (2.4000 GHz - 2.4835
GHz)
Compatible
Bluetooth profiles
Hands-Free Profile (HFP)
Handset Profile (HSP)
Advanced Audio Distribution Profile
(A2DP)
Audio Video Remote Control Profile
(AVRCP)
Maximum album number: 255
Supported sampling frequencies: 32 kHz, 44.1kHz, 48 kHz
Supported Bit-rates: 32-320 Kbps and variable bit rate
Supported video formats:
•
•
Bluetooth
Supported codecs
Receive
Transmit
Compatible USB devices:
English
Disc player
DVD
Divx
Note
•• To ensure a better playback, it is recommended that file
image size is no higher than 640 x 480, frame rate is 20
fps, data rate is no higher than 500 kbps.
SBC (Sub Band Codec)
SBC (Sub Band Codec)
EN
21
13Troubleshooting
Warning
•• Never remove the casing of this product.
To keep the warranty valid, never try to repair the product
yourself.
If you encounter problems when using this product, check
the following points before requesting service. If the problem
remains unsolved, go to the Philips Web page (www.philips.
com/support). When you contact Philips, make sure that the
product is nearby and the model number and serial number
are available.
General
No power
••
Car engine has not been started. Start the car engine.
••
Connections are incorrect.
••
The fuse has been damaged. Replace the fuse.
No sound
••
Volume is too low. adjust the volume.
••
Speaker connections are incorrect.
No response to the remote control
••
Make sure that the path between the remote control
and the unit is clear from obstacles.
••
Move the remote control close to the unit, and point it
at the iR sensor.
••
••
••
to switch to the control interface for front
Press
source or rear source.
The function is not applicable to the current media.
Replace the remote control battery.
The disc does not play.
••
The disc is upside down. Make sure that the printed
side is upwards.
••
The disc is dirty. Clean the disc with a clean, soft, lintfree cloth. Wipe the disc outwards from the center.
••
The disc is defective. Try another disc.
••
The disc is incompatible. Try another disc.
••
The recordable disc is not finalized.
••
The region code of DVD disc is not supported. Use a
disc with proper region code.
Cannot play DivX file from an SD/SDHC card or USB
storage device
••
DivX DRM protected files cannot be played if they are
saved on an SD/SDHC card or USB storage device.
Transfer it to a compatible disc instead.
No image
••
Parking wire connection is incorrect. Check the wiring.
22
EN
No image on rear monitor
•
••
Enable the signal transferring to rear monitors.
A DivX video can be played for front passengers only.
Image flashes or is distorted.
••
Video connection is improper. Check the connections.
Noise in broadcasts
••
Signals are too weak. Select another station with
stronger signals.
••
Check the connection of the car antenna.
Preset stations are lost.
••
Battery cable is not correctly connected. Connect the
battery cable to the terminal that is always live.
The fuse is broken.
••
The fuse type is incorrect. Replace it with a 15 A fuse.
••
Speaker wire or power wire is grounded. Check the
connections.
About the Bluetooth device
Music playback is unavailable on the system even after
successful Bluetooth connection.
••
The device cannot be used with the system to play
music.
The audio quality is poor after connection with a
Bluetooth-enabled device.
••
The Bluetooth reception is poor. Move the device
closer to the system or remove any obstacle between
the device and the system.
Cannot connect with the system.
••
The device does not support the profiles required for
the system.
••
The Bluetooth function of the device is not enabled.
Refer to the user manual of the device to find out how
to enable the function.
••
The system is not in the pairing mode.
••
The system is already connected with another
Bluetooth-enabled device. Disconnect that device or all
other connected devices and then try again.
The paired mobile phone connects and disconnects
constantly.
••
The Bluetooth reception is poor. Move the mobile
phone closer to the system or remove any obstacle
between the mobile phone and the system.
••
Some mobile phones may connect and disconnect
constantly when you make or end calls. This does not
indicate any malfunction of the system.
••
For some mobile phones, the Bluetooth connection
may be deactivated automatically as a power-saving
feature. This does not indicate any malfunction of the
system.
Any changes or modifications made to this device that are
not expressly approved by Philips Consumer Lifestyle may
void the user’s authority to operate the equipment.
Compliance
This product complies with the radio interference
requirements of the European Community.
This apparatus includes this label:
Your product contains batteries covered by the European
Directive 2006/66/EC, which cannot be disposed with normal
household waste.Please inform yourself about the local
rules on separate collection of batteries because correct
disposal helps to prevent negative consequences for the
environmental and human health.
Environmental information
All unnecessary packaging has been omitted. We have tried
to make the packaging easy to separate into three materials:
cardboard (box), polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can be recycled
and reused if disassembled by a specialized company. Please
observe the local regulations regarding the disposal of
packaging materials, exhausted batteries and old equipment.
Trademark notice
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by Philips is under license.
Care of the environment
Windows Media and the Windows logo are trademarks, or
registered trademarks of Microsoft Corporation in the United
States and/or other countries.
Your product is designed and manufactured with high quality
materials and components, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached
to a product it means that the product is covered by the
European Directive 2002/96/EC.
Please inform yourself about the local separate collection
system for electrical and electronic products.
Please act according to your local rules and do not dispose
of your old products with your normal household waste.
Correct disposal of your old product helps to prevent
potential negative consequences for the environment and
human health.
“Made for iPod” and “Made for iPhone” mean that an
electronic accessory has been designed to connect specifically
to iPod or iPhone respectively, and has been certified by
the developer to meet Apple performance standards. Apple
is not responsible for the operation of this device or its
compliance with safety and regulatory standards. Please note
that the use of this accessory with iPod or iPhone may affect
wireless performance.
iPod and iPhone are trademarks of Apple Inc., registered in
the U.S. and other countries.
DivX®, DivX Certified® and associated logos are trademarks
of Rovi Corporation or its subsidiaries and are used under
license.
ABOUT DIVX VIDEO: DivX® is a digital video format created
by DivX, LLC, a subsidiary of Rovi Corporation. This is an
official DivX Certified® device that plays DivX video. Visit
EN
23
English
14Notice
divx.com for more information and software tools to convert
your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified®
device must be registered in order to play purchased DivX
Video-on-Demand (VOD) movies. To obtain your registration
code, locate the DivX VOD section in your device setup
menu. Go to vod.divx.com for more information on how to
complete your registration.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
'DVD Video' is a trademark of DVD Format/Logo Licensing
Corporation.
Other trademarks and trade names are those of their
respective owners.
Copyright
2012 © Koninklijke Philips Electronics N.V.
Specifications are subject to change without notice.
Trademarks are the property of Koninklijke Philips Electronics
N.V or their respective owners. Philips reserves the right to
change products at any time without being obliged to adjust
earlier supplies accordingly.
This item incorporates copy protection technology that is
protected by U.S. patents and other intellectual property
rights of Rovi Corporation. Reverse engineering and
disassembly are prohibited.
24
EN
Specifications are subject to change without notice
© 2012 Koninklijke Philips Electronics N.V.
All rights reserved.
CED1900BT_12_UM_V2.1