PN-R703
PN-R603
LCD MONITOR
OPERATION MANUAL
IMPORTANT:
To aid reporting in case of loss or theft, please record the
product’s model and serial numbers in the space provided.
The numbers are located in the rear of the product.
Model No.:
Serial No.:
U.S.A. ONLY
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
a triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.
NOTE:
This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
This product utilizes a CR coin Lithium battery which contains a Perchlorate material.
Special handling for this material may apply,
California residents, See www.dtsc.ca.gov/hazardouswaste/perchlorate/
Others, consult local environmental officers.
U.S.A. ONLY
3
E
DEAR SHARP CUSTOMER
Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your
product, please read the Safety Precautions carefully before using this product.
SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can
result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing,
operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the
following precautions carefully before using the product.
1. Read instructions — All operating instructions must be read and understood before the product is operated.
2.Keep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future
reference.
3. Observe warnings — All warnings on the product and in the instructions must be observed closely.
4. Follow instructions — All operating instructions must be followed.
5.Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do
not use liquid cleaners or aerosol cleaners.
6.Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result
in accidents.
7.Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto
it. Be careful of equipment which drains water such as an air-conditioner.
8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.
Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life
of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings.
Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
9.Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from
resting on them.
10.The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with
impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.
11. Overloading — Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.
12.Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage flows in
the product, and inserting an object can cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.
13.Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other
dangerous conditions. Request a qualified service person to perform servicing.
14.Repair — If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service
person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls
not described in the instructions can cause damage, which often requires extensive adjustment work by a qualified
technician.
e. When the product has been dropped or damaged.
f.When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product
needs servicing.
15.Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement
parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of
unauthorized parts can result in fire, electric shock and/or other danger.
16.Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to
ensure that the product is in proper operating condition.
17.Wall mounting — When mounting the product on a wall, be sure to install the product according to the method
recommended by the manufacturer.
18.Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
E
4
SAFETY PRECAUTIONS (Continued)
19.Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment,
dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:
• Use the specified batteries only.
• Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the
compartment.
• Do not mix old and new batteries.
• Do not mix batteries of different types. Voltage specifications of batteries of the same shape may vary.
• Replace an exhausted battery with a new one promptly.
• If you will not use the remote control for a long time, remove the batteries.
• If leaked battery fluid gets on your skin or clothing, rinse immediately and thoroughly. If it gets into your eye, bathe your
eye well rather than rubbing and seek medical treatment immediately. Leaked battery fluid that gets into your eye or your
clothing may cause a skin irritation or damage your eye.
20.Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,
severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and
missile launch control in a weapon system.
21.Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in
low-temperature burns.
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may
be required to take adequate measures.
To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: DVI-D output
terminal, DVI-I input terminal, PC/AV HDMI input terminal, PC/AV D-SUB input terminal, RS-232C input/output terminals, and
DisplayPort input/output terminals.
If a monitor is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries,
particularly to children, can be avoided by taking simple precautions such as:
• Using fixing devices like wall mount brackets recommended by the manufacturer.
• Only using furniture that can safely support the monitor.
• Ensuring the monitor is not overhanging the edge of the supporting furniture.
• Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the
monitor to a suitable support.
• Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the monitor or its controls.
Especially for child safety
- Don’t allow children to climb on or play with the monitor.
- Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.
- Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care
should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.
- Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by
curious children.
5
E
TIPS AND SAFETY INSTRUCTIONS
- The TFT color LCD panel used in this monitor is made with
the application of high precision technology. However, there
may be minute points on the screen where pixels never light
or are permanently lit. Also, if the screen is viewed from
an acute angle there may be uneven colors or brightness.
Please note that these are not malfunctions but common
phenomena of LCDs and will not affect the performance of
the monitor.
- Do not display a still picture for a long period, as this could
cause a residual image.
- Never rub or tap the monitor with hard objects.
- Please understand that SHARP CORPORATION bears no
responsibility for errors made during use by the customer or
a third party, nor for any other malfunctions or damage to this
product arising during use, except where indemnity liability is
recognized under law.
- This monitor and its accessories may be upgraded without
advance notice.
- Do not use the monitor where there is a lot of dust, where
humidity is high, or where the monitor may come into contact
with oil or steam, as this could lead to fire.
- Ensure that the monitor does not come into contact with
water or other fluids. Ensure that no objects such as paper
clips or pins enter the monitor as this could lead to fire or
electric shock.
- Do not place the monitor on top of unstable objects or in
unsafe places. Do not allow the monitor to receive strong
shocks or to strongly vibrate. Causing the monitor to fall or
topple over may damage it.
- Do not use the monitor near heating equipment or in places
where there is likelihood of high temperature, as this may
lead to generation of excessive heat and outbreak of fire.
- Do not use the monitor in places where it may be exposed to
direct sunlight.
- Please be sure to constantly remove dust and garbage that
has attached to the ventilation opening. If dust collects in the
ventilation opening or the inside of the monitor, it may lead to
excessive heat, outbreak of fire, or malfunction.
Please request a cleaning of the inside of the monitor from
an authorized SHARP servicing dealer or service center.
- Images cannot be rotated on this monitor.
When using in portrait orientation, you will need to prepare
appropriately orientated content in advance.
- The AC outlet shall be installed near the equipment and shall
be easily accessible.
E
6
The Power Cord
- Use only the power cord supplied with the monitor.
- Do not damage the power cord nor place heavy objects on
it, stretch it or over bend it. Also, do not add extension cords.
Damage to the cord may result in fire or electric shock.
- Do not use the power cord with a power tap.
Adding an extension cord may lead to fire as a result of
overheating.
- Do not remove or insert the power plug with wet hands.
Doing so could result in electric shock.
- Unplug the power cord if it is not used for a long time.
- Do not attempt to repair the power cord if it is broken
or malfunctioning. Refer the servicing to the service
representative.
Manual Scope
- Microsoft, Windows and Internet Explorer are registered
trademarks of Microsoft Corporation.
- The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and
other countries.
- DisplayPort is a registered trademark of Video Electronics
Standards Association.
- Adobe, Acrobat, and Reader are either registered trademarks
or trademarks of Adobe Systems Incorporated in the United
States and/or other countries.
- This product comes with RICOH Bitmap Fonts produced and
sold by RICOH COMPANY, LTD.
- All other brand and product names are trademarks or
registered trademarks of their respective holders.
- Language of OSD menu used in this manual is English by
way of example.
- Illustrations in this manual may not exactly represent the
actual product or display.
- This manual assumes use in landscape orientation, except
where specifically noted.
LED Backlight
● The LED backlight in this product has a limited lifetime.
* If the screen gets dark or does not turn on, it may be
necessary to replace the LED backlight.
* This LED backlight is exclusive to this product and must
be replaced by an authorized SHARP servicing dealer
or service center. Please contact an authorized SHARP
servicing dealer or service center for assistance.
MOUNTING PRECAUTIONS
• This product is for use indoors.
• A mounting bracket compliant with VESA specifications is
required.
• Since the monitor is heavy, consult your dealer before
installing, removing or moving the monitor.
• Mounting the monitor on the wall requires special expertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this
work yourself. Our company will bear no responsibility
for accidents or injuries caused by improper mounting or
mishandling.
• Use the monitor with the surface perpendicular to a level
surface. If necessary, the monitor may be tilted up to 20
degrees upward or downward.
• This monitor should be used at an ambient temperature
between 32°F (0°C) and 104°F (40°C). Provide
enough space around the monitor to prevent heat from
accumulating inside.
For the monitor in landscape orientation
• Adhere to the following when installing the monitor in its
portrait orientation. Failing to adhere to the following may
cause malfunctions.
- Install the monitor such that the power LED is located on
the bottom side.
- Set the MONITOR on the MONITOR menu to PORTRAIT.
(See page 26.)
-B
e sure to clamp the power cord (supplied) onto the cable
clamp attachment using the supplied cable clamp. When
clamping the power cord, take care not to stress the
terminal of the power cord. Do not bend the power cord
excessively.
Power cord (Supplied) Cable clamp
attachment
Unit: inch [mm]
7-7/8 [200]
5/16 [7]
Cable clamp
2
[50]
2
[50]
• Use the supplied vertical sticker when you install the
monitor in portrait orientation.
2 [50]
Operation panel
For the monitor in portrait orientation
Unit: inch [mm]
7-7/8 [200]
5/16 [7]
Cover SHARP logo
2
[50]
2
[50]
Logo
Power LED
2 [50]
Do not remove the factory-affixed sticker but affix the
sticker over it. Be careful not to cover the remote control
sensor or buttons.
• If it is difficult to provide sufficient space for any reason
such as the installation of the monitor inside a housing, or
if the ambient temperature may be outside of the range
of 32°F (0°C) to 104°F (40°C), install a fan or take other
measures to keep the ambient temperature within the
required range.
• Temperature condition may change when using the monitor
together with the optional equipments recommended by
SHARP. In such cases, please check the temperature
condition specified by the optional equipments.
• Do not block any ventilation openings. If the temperature
inside the monitor rises, this could lead to a malfunction.
• Do not place the monitor on a device which generates heat.
7
E
Contents
IMPORTANT INFORMATION.............................................3
DEAR SHARP CUSTOMER...............................................4
SAFETY PRECAUTIONS...................................................4
TIPS AND SAFETY INSTRUCTIONS................................6
MOUNTING PRECAUTIONS.............................................7
Supplied Components......................................................8
Part Names........................................................................9
Connecting Peripheral Equipment................................ 11
Connection with a PC or AV equipment...................... 11
Connecting the Power Cord..........................................13
Binding Cables................................................................14
Preparing the Remote Control Unit...............................15
Installing the batteries.................................................15
Remote control operation range..................................15
Turning Power On/Off.....................................................16
Turning on the main power.........................................16
Turning power on/off...................................................16
Disabling power on/off operations...............................17
Basic Operation..............................................................18
Menu Items......................................................................20
Displaying the menu screen........................................20
Menu item details........................................................21
Adjustments for PC screen display.............................31
Initialization (Reset)/Functional Restriction Setting
(FUNCTION).....................................................................32
Controlling the Monitor with a PC (RS-232C)...............33
PC connection.............................................................33
Communication conditions..........................................33
Communication procedure..........................................33
Setting of the GAMMA user data.................................36
RS-232C command table............................................37
Controlling the Monitor with a PC (LAN)......................45
Settings to connect to a LAN.......................................45
Controlling with a PC...................................................47
[Advanced operation] Command-based control..........53
Troubleshooting..............................................................54
Specifications ................................................................56
Mounting Precautions
(For SHARP dealers and service engineers)................62
Supplied Components
If any component should be missing, please contact your dealer.
 Liquid Crystal Display Monitor: 1
 Remote control unit: 1
 Cable clamp: 2
 Cable clamp (stick-on): 2
 Power cord: 1
 R-6 battery (“AA” size): 2
 CD-ROM (Utility Disk for Windows): 1
 Setup Manual: 1
 Vertical sticker (Logo): 1
 Vertical sticker (Operation panel): 1
over SHARP logo: 1
C
Place this sticker onto the SHARP logo to cover the logo.
* SHARP Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.
* For environmental protection!
Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
E
8
Part Names
nFront view
Accessing the operation panel
1
1.
2.
3.
4.
5.
LCD panel
Remote control sensor (See page 15.)
Input switch (See page 18.)
Power switch (See page 16.)
Power LED (See page 16.)
TIPS
• Use a pointed object such as a pen tip to press the
switches.
3
2
4
5
nRear view
2
1
12
13
14
15
16
17
18
3
3
4
5
6
7
8
9
1011
19
1. Optional attachment section
This section is used to connect optional
hardware for function expansion. Offering this
attachment location is not a guarantee that
future compatible hardware attachments will
be released.
2. Vents
3. Speakers
4. Main power switch (See page 16.)
5. AC input terminal (See page 13.)
6. DisplayPort input terminal (See page 11.)
7. DisplayPort output terminal (See page 11.)
8. DVI-I input terminal (See page 11.)
9. DVI-D output terminal (See page 12.)
10. Audio1 input terminal (See page 11.)
11. Audio2 input terminal (See page 11.)
12. Optional terminal
This terminal is provided for possible future
(optional) function expansion. Offering of
this terminal is not a guarantee that future
expanded functionality will be provided.
13. LAN terminal (See page 12.)
14. RS-232C output terminal (See page 12.)
15. RS-232C input terminal (See page 12.)
16. Audio output terminal (See page 12.)
17. PC/AV D-sub input terminal (See page 11.)
18. PC/AV HDMI1 input terminal (See page 11.)
19. PC/AV HDMI2 input terminal (See page 11.)
Caution
• Consult your SHARP dealer for attachment/detachment of
optional parts.
9
E
Part Names
nRemote control unit
1
2
7
3
8
4
9
10
5
6
E
10
11
1. Signal transmitter
2. POWER button (See page 16.)
3. MUTE button (See page 18.)
4. VOL +/- buttons (See page 18.)
BRIGHT +/- buttons (See page 18.)
Cursor control ( /
/
/ ) buttons
5. DISPLAY button (See page 18.)
6. MODE button (See page 18.)
7. INPUT button (See page 18.)
8. MENU button (See page 18.)
9. ENTER button (See page 18.)
10. RETURN button (See page 18.)
11. SIZE button (See page 18.)
Connecting Peripheral Equipment
13
11
12
10
5
3
4
1
TIPS
• Images may not be displayed properly depending on the
computer (video card) to be connected.
• Use the automatic screen adjustment when a PC screen
is displayed for the first time using D-SUB[RGB] or DVI-I
(analog), or when the setting of the PC is changed. The
screen is adjusted automatically when SELF ADJUST in
the MONITOR menu is set to ON.
• If the audio output from the playback device is connected
directly to speakers or other devices, the video on the
monitor may appear delayed from the audio portion.
Audio should be played through this monitor by connecting
the playback device to the monitor’s audio input, and
connecting the monitor’s audio output to the speakers or
other devices.
• The audio input terminals used in each input mode are
factory-set as follows.
DVI-I
DisplayPort
HDMI1[PC], HDMI1[AV],
HDMI2[PC], HDMI2[AV]
D-SUB[RGB],
D-SUB[COMPONENT],
D-SUB[VIDEO]
2
9
6 7
Connection with a PC or AV equipment
Caution
• Be sure to turn off the main power switch and disconnect
the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the
equipment to be connected.
• Be careful not to confuse the input terminal with the output
terminal when connecting cables. Accidentally reversing
cables connected to the input and output terminals may
cause malfunctions and the other problems.
• Do not use any cable that has a damaged or deformed
terminal. Using such cables may cause malfunctions.
Input mode
8
Audio input terminal
(Factory setting)
Audio1 input terminal
DisplayPort input terminal
PC/AV HDMI input terminal
Audio2 input terminal
1. DisplayPort input terminal
• Use a commercially available DisplayPort cable.
• Select the audio input terminal to be used in DisplayPort
of AUDIO SELECT on the SETUP menu.
When DisplayPort is selected, connection to the audio
input terminal is unnecessary.
2. DVI-I input terminal
• Use a commercially available signal cable (DVI-I 29 pin).
• Select the audio input terminal to be used in DVI-I of
AUDIO SELECT on the SETUP menu.
• If the display is not shown properly, set EDID SELECT
(DVI-I) of INPUT SELECT on the SETUP menu according
to the device to be connected.
3. PC/AV HDMI1 input terminal
4. PC/AV HDMI2 input terminal
• Use a commercially available HDMI cable (conforming to
the HDMI standard).
• Set HDMI1 or HDMI2 of INPUT SELECT on the SETUP
menu according to the device to be connected.
• Select the audio input terminal to be used in HDMI1[AV],
HDMI1[PC], HDMI2[AV] or HDMI2[PC] of AUDIO SELECT
on the SETUP menu.
When HDMI is selected, connection to the audio input
terminal is unnecessary.
5. PC/AV D-sub input terminal
• Set D-SUB of INPUT SELECT on the SETUP menu
according to the device to be connected.
• To use with D-SUB[VIDEO], connect the green terminal to
the device’s video output.
• Select the audio input terminal to be used in D-SUB[RGB],
D-SUB[COMPONENT] or D-SUB[VIDEO] of AUDIO
SELECT on the SETUP menu.
6.
7.
•
•
Audio1 input terminal
Audio2 input terminal
Use an audio cable without resistance.
Set the audio input terminal to be used in each input
mode in AUDIO SELECT on the SETUP menu.
11
E
Connecting Peripheral Equipment
8. DisplayPort output terminal
• The video of the DisplayPort input can be output to an
external device.
• Use a commercially available DisplayPort cable.
• Outputting HDCP-encrypted video requires an external
device which supports HDCP.
• This terminal allows the daisy chain connection (up to 25
monitors or up to 4 monitors when transmitting HDCPencoded content) by connecting the monitors to each
other through the DisplayPort input terminal of each
monitor.
9. DVI-D output terminal
• The video of the DVI-I (digital) input can be output to an
external device.
• Outputting HDCP-encrypted video requires an external
device which supports HDCP.
• This terminal allows the daisy chain connection of up
to 5 monitors by connecting the monitors to each other
through the DVI-I input terminal of each monitor.
TIPS
• The length of the signal cables or surrounding environment
may affect the image quality.
• The output screen may not display properly when using
terminals other than DVI-I for the input mode. In this case,
turn off the power to all the monitors connected in a daisy
chain and then turn the power on again.
• When connecting monitors in a daisy chain set AUTO
INPUT CHANGE to OFF.
• Video output is disabled in the following cases:
When the power is turned off
When the monitor is in input signal waiting mode
10. Audio output terminal
• The output sound varies depending on the input mode.
• The volume of the output sound can be fixed by setting
AUDIO OUTPUT of AUDIO OPTION on the SETUP
menu.
• It is not possible to control the sound output from the
audio output terminals with the AUDIO menu.
1. RS-232C output terminal
1
12. RS-232C input terminal
• You can control the monitor from a PC by connecting a
commercially available RS-232 straight cable between
these terminals and the PC.
13. LAN terminal
• You can control the monitor from a PC on a network by
connecting a commercially available LAN cable between
this terminal and a network.
E
12
Connecting the Power Cord
Caution
• Use only the power cord supplied with the monitor.
1. Turn off the main power switch.
2. Plug the power cord (supplied) into the AC input terminal.
3. Plug the power cord (supplied) into the AC power outlet.
Main power switch
1
AC input terminal
Power cord (Supplied)
2
3 For power
outlet
13
E
Binding Cables
The cables connected to the terminals on the rear of the
monitor can be fastened with the cable clamp.
Insert the cable clamp into the cable clamp attachment on the
rear of the monitor and fasten the cables.
Use the supplied cable clamp (stick-on) affixed to the rear of the
monitor.
Where you attach the cable clamp, please remove the dirt.
Cable
Cable clamp
attachment
(2)
Cable clamp
(1)
* Do not cover the vents.
E
14
(3)
Preparing the Remote Control Unit
Installing the batteries
1. Press the cover gently and slide it in the direction of the arrow.
2. See the instructions in the compartment and put in the supplied batteries (R-6 (“AA” size) x 2) with their plus (+) and minus (-)
sides oriented correctly.
3. Close the cover.
TIPS
• When the batteries become exhausted, replace them with new (commercially available) batteries.
• The supplied batteries (R-6 (“AA” size) x 2) may become exhausted quickly depending on how they are stored.
• If you will not be using the remote control for a long time, remove the batteries.
• Use manganese or alkaline batteries only.
Remote control operation range
Operation panel in
The remote control can be operated even when the operation panel is stored inside the monitor.
Point the remote control toward the remote control sensor on the bottom of the monitor (or the right side of the monitor if using
portrait orientation).
For the monitor in landscape orientation
For the monitor in portrait orientation
0º
16.4 feet
(5m)
35º
10º
10º
10º
10º
0º
16.4 feet Remote control sensor
(5m)
10º
35º
10º
Remote control sensor
10º
10º
Operation panel out
Point the remote control toward the remote control sensor on the front of the monitor.
For the monitor in landscape orientation
10º
10º
10º
16.4 feet Remote control sensor
(5m)
10º
For the monitor in portrait orientation
10º
10º
10º
16.4 feet
(5m)
10º
Remote control sensor
TIPS
• Do not expose the remote control unit to shock by dropping or stepping on it. This could lead to a malfunction.
• Do not expose the remote control unit to liquids, and do not place it in an area with high humidity.
• The remote control unit may not work properly if the remote control sensor is under direct sunlight or strong lighting.
• Objects between the remote control unit and the remote control sensor may prevent proper operation.
• Replace the batteries when they run low as this may shorten the remote control’s operation range.
• If a fluorescent light is illuminated near the remote control unit, it may interfere with proper operation.
• Do not use it with the remote control of other equipment such as air conditioner, stereo components, etc.
15
E
Turning Power On/Off
Caution
• Turn on the monitor first before turning on the PC or
playback device.
Turning power on/off
Press the POWER button or POWER switch to turn the power
ON/OFF.
Turning on the main power
Main power switch
Power switch Power LED
Status
Caution
• The main power must be turned on/off with the main power
switch. Do not connect/disconnect the power cord or turn
the breaker on/off while the main power switch is on.
• When switching the main power switch or the POWER
button off and back on, always wait for at least 5 seconds.
• For a complete electrical disconnection, pull out the main
plug.
Status of the monitor
Green lit
Power on
Orange lit
Power off (Standby mode)
Green flashing
Input signal waiting mode
It is possible to check the power LED even when the operation
panel is stored inside the monitor.
Power LED
Caution
• When switching the main power switch or the POWER
button off and back on, always wait for at least 5 seconds.
A short interval may result in a malfunction.
TIPS
• When the main power switch is off, the monitor cannot be
turned on.
• If the monitor is in the input signal standby mode and you
press the POWER button on the remote control unit, the
monitor enters standby mode.
• Setting the SCHEDULE flashes the power LED alternately
in red and orange in standby mode.
• To disable the logo screen from displaying when turning the
power ON, set LOGO SCREEN to OFF on the OTHERS
menu. (See page 28.)
E
16
Turning Power On/Off
nDate/time setting
• If the time has yet to be set when the monitor is first turned
on, the date/time setting screen appears. Set the date and
time.
DATE/TIME SETTING
/
:
/
01 / 01 / 20 13
12 : 00
Disabling power on/off operations
Power on/power off operations can be disabled in order to
protect the monitor from an accidental power off. Set the
ADJUSTMENT LOCK in FUNCTION menu to “ON 2”. (See
page 32.)
:
AM
OK···[ENTER] CANCEL···[RETURN]
1. Press
or
or
press
2. Press ENTER .
to select the date and time, and
to change the numerical values.
• Be sure to set the date and time.
• The date/time setting screen will close automatically if
no operation is performed for about 15 seconds. The
date and time can be set using DATE/TIME SETTING
from the SETUP menu when the date/time setting screen
disappears.
TIPS
Set the date in “Month/Day/Year” order.
Set the time on a 12-hour basis.
The clock is maintained by the internal battery.
If you already set the time but the date/time setting
screen appears when the power is turned on, the
internal battery may be exhausted. Please contact an
authorized SHARP servicing dealer or service center for
assistance with battery replacement.
• Estimated service life of the internal battery: About 5
years (depending on monitor operation)
• The initial battery was inserted at the factory when the
monitor was shipped, so it may run out of power before
its expected operation life.
•
•
•
•
17
E
Basic Operation
4. VOL +/- (Volume adjustment)
Pressing
or
displays the VOLUME menu when the
menu screen is not displayed.
1
VOLUME
2
3
Press
or
to adjust the volume of the sound.
* If you do not press any buttons for about 4 seconds, the
VOLUME menu automatically disappears.
4
5
6
5. BRIGHT +/- (Brightness adjustment)
Pressing
or
displays the BRIGHT menu when the
menu screen is not displayed.
7
BRIGHT
8
9
1. INPUT (Input mode selection)
or
to select the input
The menu is displayed. Press
ENTER
mode, and press
to enter.
* You can select the input terminal by pressing the input
switch of the monitor.
Video
DVI-I
DVI-I input terminal
DisplayPort
DisplayPort input terminal
HDMI1[PC]
PC/AV HDMI1 input
terminal*1
HDMI1[AV]
HDMI2[PC]
HDMI2[AV]
D-SUB[RGB]
D-SUB[COMPONENT]
D-SUB[VIDEO]
PC/AV HDMI2 input
terminal*2
Audio
*4
PC/AV D-sub input
terminal*3
*1 Select the terminal to be used in HDMI1 of INPUT
SELECT. (See page 24.)
*2 Select the terminal to be used in HDMI2 of INPUT
SELECT. (See page 24.)
*3 Select the terminal to be used in D-SUB of INPUT
SELECT. (See page 24.)
*4 Select the terminal for AUDIO SELECT which is used for
audio input. (See page 24.)
2. MUTE
Turns off the volume temporarily.
Press the MUTE button again to turn the sound back to the
previous level.
3. MENU
Displays and turns off the menu screen. (see page 20.)
E
18
15
Press
or
to adjust the brightness.
* If you do not press any buttons for about 4 seconds, the
BRIGHT menu automatically disappears.
10
Input mode
15
6. ENTER
Confirms the setting.
7. RETURN
Returns to the previous screen.
8. SIZE (Screen size selection)
The menu is displayed.
Press
or
to select the screen size. (See page 19.)
9. DISPLAY
Displays monitor information.
The display changes from INFORMATION1 →
INFORMATION2 → clear display, and so on every time you
press this button.
• The display disappears automatically after about 15
seconds.
• LAN is displayed during LAN communication.
• If LAN is displayed in red, there is a duplicate IP address.
10.MODE (Color mode selection)
Each time you press this button, the color mode changes in
the following order:
STD (Standard) → VIVID → sRGB →
HIGH ILLUMINANCE → STD...
• HIGH ILLUMINANCE is a display with colors suited to
bright locations.
• sRGB applies to PC input only.
sRGB is international standard of color representation
specified by IEC (International Electrotechnical
Commission). Color conversion is made in taking account
of liquid crystal’s characteristics and represents color tone
close to its original image.
Basic Operation
nSwitching the screen size
Even when the screen size is changed, the display may remain the same depending on the input signal.
WIDE
ZOOM 1
PC input
Displays image so it fills the entire screen.
AV input
An image with a 4:3 aspect ratio is stretched to fill the entire
screen.
PC input
An image with a 4:3 aspect ratio is enlarged to fill the entire screen
without changing the aspect ratio. The edges of the image may be
cut off.
AV input
ZOOM 2
PC input
Use this size if ZOOM 1 cuts off the subtitles.
AV input
NORMAL
Dot by Dot
PC input
Displays image so it fills the screen without changing the aspect
ratio of the input signals.
AV input
Displays the entire image of the aspect ratio of 4:3 without
changing the aspect ratio.
PC input
Displays the dots of the signals input from the connected PC as
the corresponding dots on the screen.
AV input
Displays the dots of the input signals as the corresponding dots on
the screen.
TIPS
• Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial
or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright
Law, so please be careful.
• When “Enlarge” is set, the screen size is fixed to “WIDE” mode.
• When dual-screen display is selected, the screen size cannot be changed.
• The appearance of the original video may change if you select a screen size with a different aspect ratio than the original
image (e.g. TV broadcast or video input from external equipment).
• When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this
monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen
size to “NORMAL”.
• When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen
size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the
edges of the screen. This is due to the characteristics of the software, and is not a malfunction.
• Depending on the original image size, black bands may remain at the edges of the screen.
19
E
Menu Items
Displaying the menu screen
TIPS
Video and audio adjustment and settings of various functions
are enabled. This section describes how to use the menu
items. See pages 20 to 29 for details of each menu items.
• The menu will differ depending on the input mode.
• The menu screen will close automatically if no operation is
performed for about 15 seconds. (DATE/TIME SETTING,
SCHEDULE and LAN SETUP screens will close in about 4
minutes.)
Caution
• Do not turn the main power switch off while the menu items
are being displayed. Doing so may initialize the settings.
PICTURE
(Adjusting CONTRAST in the PICTURE menu)
MENU
SCREEN
SCREEN
PICTURE
AUDIO
SETUP
MONITOR
MULTI/PIP
OTHERS
MULTI/PIP
600
25
610
37
50
50
OTHERS
or
to select PICTURE, and press
3. Press
or
to select CONTRAST.
PICTURE
AUDIO
SETUP
MONITOR
MULTI/PIP
OTHERS
or
AUDIO
SETUP
MONITOR
MULTI/PIP
OTHERS
For items that have
RETURN
then press
.
20
MENU
BACK···[RETURN]
D-SUB[RGB]
MOVE OSD···[DISPLAY]
1920x1080
V: 60 Hz
5. Press
H: 67.5 kHz
to adjust the setting.
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
COLOR ADJUSTMENT
ADVANCED
RESET
, press
31
40
30
30
30
12
H: 67.5 kHz
ENTER
PICTURE
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
COLOR ADJUSTMENT
ADVANCED
RESET
BACK···[RETURN]
, make settings and
to close the menu screen.
D-SUB[RGB]
31
30
30
30
30
12
H: 67.5 kHz
BACK···[RETURN]
TIPS
• Items that cannot be selected appear in gray.
(e.g. Function not supported by the current input signal)
31
30
30
30
30
12
PICTURE
PICTURE
.
D-SUB[RGB]
MOVE OSD···[DISPLAY]
1920x1080
V: 60 Hz
4. Press
ENTER
2
1 Name of the menu
2 Input mode
3 An item being selected (highlighted)
4 Screen resolution of input signal, and other data.
OK···[ENTER] BACK···[RETURN]
V: 60 Hz H: 67.5 kHz
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
COLOR ADJUSTMENT
ADVANCED
RESET
3
MOVE OSD···[DISPLAY]
1920x1080
V: 60 Hz
2. Press
SCREEN
MONITOR
RESOLUTION SETTING
RESET
PICTURE
E
SETUP
D-SUB[RGB]
1920x1080
SCREEN
AUDIO
to display the menu screen.
AUTO
CLOCK
PHASE
H-POS
V-POS
H-SIZE
V-SIZE
1
SCREEN
nExample of operation
1. Press
nMenu screen display
4
Menu Items
Menu item details
The menu will differ depending on the input mode.
nSCREEN
You can move the menu screen display position each time
DISPLAY
is pressed.
AUTO (D-SUB[RGB]/DVI-I (analog))
The CLOCK, PHASE, H-POS, and V-POS are automatically adjusted.
ENTER
Pressing
performs adjustment. Use this automatic adjustment when you use the D-SUB[RGB] or DVI-I (analog) to display
a PC screen for the first time or when you change the setting of the PC. (See page 31.)
CLOCK (D-SUB[RGB]/DVI-I (analog))
Adjusts frequency for sampling clock for applicable video.
Adjust when there is flickering in the form of vertical stripes.
When using the adjustment pattern (see page 31), make adjustments so that no vertical stripe noise appears in it.
PHASE (D-SUB[RGB]/DVI-I (analog))
Adjusts sampling clock phase for applicable video. Useful when small characters appear with low contrast and/or there are
flickers at corners. When using the adjustment pattern (see page 31), make adjustments so that no horizontal stripe noise
appears in it.
* Adjustments to PHASE should be made only after CLOCK has been correctly set.
H-POS
Adjust the horizontal position of the image.
V-POS
Adjust the vertical position of the image.
H-SIZE
Adjust the horizontal size of the image.
V-SIZE
Adjust the vertical size of the image.
RESOLUTION SETTING (D-SUB[RGB]/DVI-I (analog))
H-RESOLUTION
Sets proper horizontal resolution when the resolution of input signals is not recognized properly.
(Adjustment may be impossible with some signals.)
V-RESOLUTION
Sets proper vertical resolution when the resolution of input signals is not recognized properly.
(Adjustment may be impossible with some signals.)
RESET
Resets the values of the SCREEN menu items to the factory preset values.
ENTER
Select “ON” and then press
.
21
E
Menu Items
nPICTURE
You can move the menu screen display position each time
DISPLAY
is pressed.
BRIGHT
Adjusts the backlight brightness. (In PIP mode, the main side setting is reflected in the image.)
CONTRAST
Adjusts the difference between the bright and dark portions of the image.
BLACK LEVEL
Adjusts the entire brightness of the video signals.
TINT
Adjusts the hue. Selecting + changes the color towards green, and selecting - changes it towards magenta.
COLORS
Adjusts the color intensity.
SHARPNESS
Adjusts the sharpness of the image.
COLOR ADJUSTMENT
COLOR MODE
Changes the color mode on the screen. The color mode on the screen can also be changed using a remote control unit. (See
page 18.)
* sRGB is PC input only. See page 18 for details.
(In PIP mode, the main side setting is reflected in the image.)
WHITE BALANCE
THRU...............Displays the input signal level as is. (for PC input only)
PRESET...........Selects the color temperature using PRESET.
USER...............Used for adjusting R-/G-/B-CONTRAST and R-/G-/B-OFFSET respectively.
(In PIP mode, the main side setting is reflected in the image.)
PRESET
Selects the color temperature when the WHITE BALANCE is set to PRESET.
The setting values are shown for reference. The color temperature of the screen varies over time. This function is not
intended to keep the color temperature constant.
USER
Adjusts each item when the WHITE BALANCE is set to USER.
R-CONTRAST..... Adjusts bright-toned red component.
G-CONTRAST.... Adjusts bright-toned green component.
B-CONTRAST..... Adjusts bright-toned blue component.
R-OFFSET.......... Adjusts dark-toned red component.
G-OFFSET.......... Adjusts dark-toned green component.
B-OFFSET.......... Adjusts dark-toned blue component.
COPY TO USER
Copies the value of white set for PRESET to the USER setting.
ENTER
Select “ON” and then press
.
(In the case other than white, color tone may differ from the PRESET.)
GAMMA
Selects the gamma. USER sets the gamma to the sent value (see page 36).
(In PIP mode, the main side setting is reflected in the image.)
FLESH TONE (AV input)
Adjust the hue control.
When FLESH TONE is set to LOW or HIGH, C.M.S.-HUE/-SATURATION/-VALUE cannot be set.
C.M.S.-HUE (AV input)
Adjusts color tone with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).
C.M.S.-SATURATION (AV input)
Adjusts color vividness with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).
C.M.S.-VALUE (AV input)
Adjusts color brightness with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).
E
22
Menu Items
ADVANCED
AUTO (D-SUB[RGB]/DVI-I (analog))
The ANALOG GAIN and ANALOG OFFSET are automatically adjusted.
ENTER
Pressing
performs adjustment.
ANALOG GAIN (D-SUB[RGB]/DVI-I (analog))
Adjusts the bright portions of the video input signal.
ANALOG OFFSET (D-SUB[RGB]/DVI-I (analog))
Adjusts the dark portions of the video input signal.
3D-NR (AV input)
Reduce the noise of playback images on video.
Setting a higher level reduces more noise. However, it may cause blurring on an image.
MPEG-NR (AV input)
Reduce block noise caused by digital compression.
3D-Y/C (D-SUB[VIDEO])
Specify whether to perform 3-dimension Y/C separation.
If dot interference or cross-color is occurring in fast-motion scenes, selecting “OFF” may improve the image quality.
RGB INPUT RANGE (DVI-I/HDMI[PC]/HDMI[AV]/D-SUB[RGB]/DisplayPort)
Sets the RGB input signal range. When using HDMI or DisplayPort set to AUTO, the RGB input signal is detected
automatically. Use AUTO normally.
If the RGB input signal range cannot be set appropriately even when using AUTO, set according to the image. When the
setting is different, images will be displayed with washed out blacks and compressed gradients.
ACTIVE CONTRAST (AV input)
Automatically adjusts the contrast according to the image.
(In PIP mode, the main side setting is reflected in the image.)
The adjustment operation may not be smooth depending on the image. In this case select OFF.
DISPLAY COLOR PATTERN
Displays a color pattern. Can be displayed while the menu screen is displayed, so you can refer to the pattern while adjusting
the image.
OFF................No pattern display.
WHITE............White single color pattern display.
RED...............Red single color pattern display.
GREEN..........Green single color pattern display.
BLUE..............Blue single color pattern display.
USER.............Red/green/blue mixed color pattern display. When USER is selected, set each color’s level.
RESET
Resets the values of the PICTURE
menu items to the factory preset values.
ENTER
Select “ON” and then press
.
23
E
Menu Items
nAUDIO
TREBLE
Adjusts the volume of treble-level sound.
BASS
Adjusts the volume of bass-level sound.
BALANCE
Adjusts the balance of the audio sound between right and left.
RESET
Resets the values of the AUDIO menu items to the factory preset values.
ENTER
.
Select “ON” and then press
nSETUP
DATE/TIME SETTING
to select the date and time, and press
or
or
Set the date and time. Press
Set the date in “Month/Day/Year” order.
Set the time on a 12-hour basis. (Factory default)
DATE/TIME FORMAT
Sets the date/time display format.
DATE...................MM/DD/YYYY, DD/MM/YYYY, YYYY/MM/DD
(YYYY: Year, MM: Month, DD: Day)
TIME....................Select 12- or 24-hour time.
SCHEDULE (See page 30.)
You can turn the power on/off and change the screen brightness at a specified time.
LANGUAGE
Sets the display language for the menu screen.
INPUT SELECT
to change the numerical values.
HDMI1/HDMI2
Select the input mode to be used in PC/AV HDMI1 and PC/AV HDMI2 input terminals.
D-SUB
Select the input mode to be used in PC/AV D-Sub input terminal. Select SET after selecting the input mode, and then press
ENTER
.
HDMI AUTO VIEW
When ON is selected, the screen size is adjusted automatically according to the screen size control signal included in the
video signal input from the AV HDMI input terminal.
HOT PLUG CONTROL
Sets whether to use hot plug control for the DVI-I, PC/AV HDMI1, and PC/AV HDMI2 input terminals.
EDID SELECT (DVI-I)
Normally, leave this setting as AUTO.
If the display is not shown properly, change the setting according to the connected device.
AUDIO SELECT
Selects the terminal used to input audio signals in each input mode.
AUDIO OPTION
AUDIO OUTPUT
Sets the volume of sound output from the audio output terminals.
When set to VARIABLE 2, sound will not be output from the built-in speaker.
VARIABLE1......... You can adjust the volume using VOLUME.
VARIABLE2......... You can adjust the volume using VOLUME.
FIXED................. Fixes the sounds.
AUDIO INPUT LEVEL 1/2
Selects the maximum audio input level of the audio input 1, 2 terminals.
MONAURAL AUDIO
Outputs audio signals as monaural.
E
24
Menu Items
COMMUNICATION SETTING
RS-232C/LAN SELECT
Selects the method with which to control the monitor from the computer.
BAUD RATE
Selects the communication speed used for RS-232C communication.
LAN SETUP
Configures the settings to control the monitor from the computer via LAN. (See page 45.)
AUTO ASSIGN FIXED IP ADDR.
Can be enabled when RS-232C/LAN SELECT is LAN and the DHCP CLIENT is OFF.
Set DHCP CLIENT to OFF for the monitor connected to the RS-232C output terminal and the daisy chain of connected
monitors that follows. Fixed IP addresses are automatically allocated.
If the IP address is a duplicate with a network device other than a monitor, individually change the IP address.
ID SETTING
ID No. SET
Assigns ID numbers to monitors connected in a daisy chain (see page 34), using the RS-232 cables.
The numbers 1 to 255 are available for ID numbers.
If “0” is set, the system regards this as the state where no ID number is set.
AUTO ASSIGN ID No.
ID No. to be used will be automatically assigned when multiple monitors are connected with RS-232C.
ENTER
Select ON, then press
.
Perform operations using the first monitor in the daisy chain.
COPY SETTING VALUE
When the monitor has been connected to multiple monitors by RS-232C, the settings in the monitor can be copied to the
monitor connected to the RS-232C output terminal and to the daisy chain of connected monitors that follows.
Selects the settings to copy with COPY SETTING VALUE TARGET.
“PICTURE” ONLY...... Copies the PICTURE menu settings.*
ALL............................ Copies all the settings.*
ENTER
.
Select the ID No. of the monitor that you would like copy to with COPY TO ID No., then select COPY and press
If you select ALL, settings will be copied to all monitors.
ENTER
. The ID No. will be
When you would like to confirm the ID No. that is set to the monitor, select ID No. DISPLAY and press
displayed on the screen.
* Certain setting details such as ANALOG GAIN, ANALOG OFFSET, and DISPLAY COLOR PATTERN cannot be copied.
25
E
Menu Items
nMONITOR
MONITOR
Select the installation direction of the monitor.
LANDSCAPE.............Landscape orientation
PORTRAIT................Portrait orientation
OSD H-POSITION
Adjusts the horizontal display position of menu screen.
OSD V-POSITION
Adjusts the vertical display position of menu screen.
STANDBY MODE
When STANDARD is selected, startup time from standby mode is reduced. Note, however that, more power will be consumed
in standby mode.
When LOW POWER is selected, current consumption is reduced while the monitor is in standby mode. Note, however, that the
startup time from standby mode becomes longer.
If set to LOW POWER, certain RS-232C commands cannot be used in standby mode, and control via LAN will be disabled.
OFF IF NO OPERATION
Determines whether or not to set the monitor to go into standby mode when there is no operation from the remote control unit,
RS-232C commands, or LAN for over 4 hours.
POWER ON DELAY
If SET is set to ON, you can delay the screen display after the monitor is turned on. When ON is selected, set the delay time
with INTERVAL (interval can be set up to 60 seconds in units of 1 second).
When this function is activated, the power LED flashes (at approx. 1 second interval) in orange.
SELF ADJUST
On a D-SUB[RGB]/DVI-I (analog) screen, specify whether to perform screen adjustment automatically or not.
When ON is selected, the screen is automatically adjusted when its resolution is 800 x 600 or higher and the timing of input
signals changes. “ADJUSTING” appears on the screen during the adjustment.
If SELF ADJUST is set to ON, set the time it takes to start the SELF ADJUST function in START TIMING.
For images with black edges, etc., depending on the signal, adjustment may not be possible. In this case select OFF. (Perform
manual adjustment of the screen.)
E
26
Menu Items
nMULTI/PIP
MULTI
ENLARGE (See page 29.)
Sets whether or not to use the enlarge function.
ADVANCED (ENLARGE)
ENLARGE H / ENLARGE V
..........Sets the number of screen splits (number of monitors) in the horizontal/vertical direction used for the enlargement.
ENLARGE-POS
..........Specify the split screen to be displayed when the enlargement function is used.
H-POS / V-POS
..........Adjust the horizontal/vertical position of the enlarged screen.
BEZEL ADJUST
Sets whether or not to use the frame correction function.
ADVANCED (BEZEL ADJUST)
BEZEL ADJUST (TOP) / BEZEL ADJUST (BOTTOM) /BEZEL ADJUST (RIGHT) / BEZEL ADJUST (LEFT)
..........Adjusts so that the top/bottom/left/right connecting joints of grouped units will be displayed smoothly when a group
of monitors are aligned in multiples to display a single image.
BEZEL (TOP) / BEZEL (BOTTOM) / BEZEL (RIGHT) / BEZEL (LEFT)
..........Sets the frame width of the display.
PIP/PbyP
PIP MODES
Sets the display method.
OFF.......... Displays one screen.
PIP........... Displays a sub screen inside a main screen.
PbyP......... Displays a main screen and a sub screen in a line.
PbyP2...... Displays a main screen which measures 1280 pixels in the longest direction and a sub screen in a line.
PIP SIZE
Sets the size of the sub screen in PIP mode.
PIP H-POS
Adjusts the horizontal position of the sub screen in PIP mode.
PIP V-POS
Adjusts the vertical position of the sub screen in PIP mode.
PIP BLEND
In PIP mode, use this menu item to display the sub screen transparently.
PIP SOURCE
Selects the input signal of the sub screen in PIP, PbyP, or PbyP2 mode.
SOUND CHANGE
Sets the sound which is output in PIP, PbyP, or PbyP2 mode.
If the main screen is displayed as a full screen by the AUTO OFF function, the sound for the main screen is output even
when the sound for the sub screen is specified.
MAIN POS
Sets the position of the main screen in PbyP or PbyP2 mode.
PbyP2 POS
Sets the position of the sub screen in PbyP2 mode.
AUTO OFF
Sets the display method when no signals for the sub screen are input in PIP, PbyP, or PbyP2 mode.
MANUAL........Displays a main screen and a black sub screen.
AUTO.............Displays the main screen as a full screen.
27
E
Menu Items
nOTHERS
SCREEN MOTION
PATTERN
Residual images are reduced by moving the screen.
OFF..................SCREEN MOTION function is disabled.
PATTERN1.......The whole screen moves vertically and horizontally.
PATTERN2.......A black screen spreads from the bottom of the screen and then shrinks to the bottom of the screen. If the
monitor is installed in the portrait orientation, a black screen spreads from the left end of the screen and then
shrinks to the left end of the screen.
PATTERN3.......A black bar moves from the left end to the right end of the screen. If the monitor is installed in the portrait
orientation, a black bar moves from the top to the bottom of the screen.
PATTERN4.......Black screens appear from both the top and bottom of the screen, and the displayed image is compressed
into the central field. If the monitor is installed in the portrait orientation, the screen is compressed from the
left and right ends.
PATTERN1
PATTERN2
PATTERN3
PATTERN4
MOTION TIME 1
Specify a time period (operating interval) until SCREEN MOTION starts.
MOTION TIME 2
Specify a time period during which SCREEN MOTION operates (time period during which the screen will move).
POWER MANAGEMENT
POWER MANAGEMENT determines whether or not to switch modes from no signal to the input signal standby mode.
AUTO INPUT CHANGE
Specify whether to change inputs automatically. When ON is selected and no signal is present in the selected input mode,
AUTO INPUT CHANGE automatically changes the selected mode to another mode where a video signal is present.
When video signals exist in multiple input modes, the switching priority is as follows:
DVI-I, DisplayPort, HDMI1, HDMI2, D-SUB
(Input mode switching may take 15 seconds or more, depending on the connected equipment. Input signals may not be
detected properly and a priority may change, depending on the connected equipment or video signals.)
LOGO SCREEN
Sets whether or not to display the logo screen.
INPUT SIGNAL (D-SUB[RGB]/DVI-I (analog))
If a computer connected to the D-SUB[RGB]/DVI-I (analog) outputs any of the following resolutions, make a selection from the
following options.
480 LINES...........AUTO, 640x480 or 848x480
768 LINES...........AUTO, 1024x768, 1280x768, or 1360x768
1050 LINES.........1400x1050 or 1680x1050
ZOOM2 SPECIAL SETTING (See page 29.)
SCAN MODE (AV input)
Sets the scan mode used for AV mode input.
MODE1................Over-scan display
MODE2................Under-scan display
MODE3................Under-scan display when the input signal is 1080i/p. Otherwise, over-scan display
*E
ven when MODE1 is selected, under-scan display is used when the input signal is 1080i/p and the screen size is Dot by Dot.
COLOR SYSTEM (D-SUB[VIDEO])
Select the color system of the AV equipment which is connected to PC/AV D-sub input terminal. (AUTO / PAL / PAL-60 /
SECAM / NTSC3.58 / NTSC4.43)
When AUTO is selected, the color system is automatically set according to the input signal.
TIPS
• When WHITE BALANCE is set to THRU, BLACK LEVEL, CONTRAST, TINT, COLORS, RGB INPUT RANGE, GAMMA and
COPY TO USER cannot be set.
• If COLOR MODE is set to sRGB, the following items cannot be set.
WHITE BALANCE, PRESET, USER, COPY TO USER, and GAMMA
• When the COLOR MODE is set to VIVID or HIGH ILLUMINANCE, GAMMA can not be adjusted.
• STANDBY MODE cannot be set to LOW POWER when SCHEDULE is effective.
• When displaying the color pattern, it is possible to adjust certain items of the PICTURE menu.
Non-adjustable items cannot be selected.
Audio input from the HDMI input terminal is also not output.
E
28
Menu Items
nDual screen display
nEnlarge
You can display two screens simultaneously.
Set this function with PIP MODES of PIP/PbyP in the MULTI/
PIP menu.
• You can align several monitors and integrate them into a
single large screen to display.
• Up to 5 monitors can be aligned in both the horizontal and
vertical directions.
• Each monitor displays enlarged views of separated images.
(Example)
Horizontal direction: 2 monitors
Vertical direction: 2 monitors
A sub screen is displayed
inside a main screen.
PIP
Main screen
Sub
screen
PbyP
Main
screen
Sub
screen
PbyP2
Main screen
Sub
screen
A main screen and a sub
screen are displayed in a
line.
Displays a main screen
which measures 1280
pixels in the longest
direction and a sub
screen in a line.
* The currently selected input signal is displayed on the main
screen.
* The following combinations are available for display:
DisplayPort - HDMI1 or HDMI2
DisplayPort - D-SUB[RGB]
DisplayPort - D-SUB[COMPONENT]
DisplayPort - D-SUB[VIDEO]
DVI-I - HDMI1 or HDMI2
DVI-I - D-SUB[COMPONENT]
DVI-I - D-SUB[VIDEO]
TIPS
• You might infringe on a copyright of the author which is
protected by copyright law when you display the images of
the computer screen and television/VCR simultaneously for
profit-making or to show the image to the public.
• The screen size for dual-screen display is the same as
the screen size for single-screen display. The Dot by Dot
screen is displayed in NORMAL size except when it is set
as the PIP main screen.
• When dual-screen display is selected, the SCREEN
MOTION function is disabled.
• When dual-screen display is selected, the AUTO INPUT
CHANGE function is disabled.
• When dual-screen display is selected, the screen cannot
be enlarged.
• When dual-screen display is selected, the INPUT SELECT
options cannot be set.
• When an interlaced signal (1080i, 480i, video) is input to
the sub screen, horizontal lines may flicker. If this happens,
display the image on the main screen.
Horizontal direction: 3 monitors
Vertical direction: 2 monitors
Setting procedure
Set using MULTI in the MULTI/PIP menu.
1. Set ENLARGE to ON.
2. Select ADVANCED (ENLARGE).
3. Set the number of monitors aligned in the horizontal
direction in ENLARGE H.
4. Set the number of monitors aligned in the vertical
direction in ENLARGE V.
5. Set the section of the separated image to be displayed
on each monitor in ENLARGE-POS.
ENTER
.
1)Press
,
2)Press
MENU
press
.
,
or
to select position, then
TIPS
• When Enlarge is used, the SCREEN MOTION function is
disabled.
• When Enlarge is used, the AUTO INPUT CHANGE function
is disabled.
• When Enlarge is used, the HDMI AUTO VIEW function is
disabled.
nZOOM2 SPECIAL SETTING
If you connect a laptop computer with any of the following
screen resolutions and black bands appear around the screen,
set ZOOM2 SPECIAL SETTING of INPUT SIGNAL on the
OTHERS menu to ON and then select ZOOM2 in the SIZE
setting.
This displays the area inside the black band.
Laptop computer
resolution
Corresponding signal*1
1280x800
1280x1024, 1280x960, 1400x1050*2
1280x600
1280x720
1024x600
1024x768
*1: This setting is effective only when the screen resolution,
including the black band, is one of the resolutions listed
above.
*2: U
se the automatic screen adjustment.
29
E
Menu Items
nSCHEDULE
Caution
You can set the time to switch the monitor on and off.
Set this function with SCHEDULE in the SETUP menu. (See
page 24.)
D-SUB[RGB]
SCHEDULE
(2)
No. (1) POWER
–
–
–
–
–
–
–
–
––
––
––
––
––
––
––
––
– –/– –/– – – –
(3)
–––
DAY OF THE WEEK
–
–– - ––
–
–
–
–
–
–
–
1920x1080
––
––
––
––
––
––
––
-
––
––
––
––
––
––
––
– –:– –:– – – –
(4)
TIME
––:––
––:––
––:––
––:––
––:––
––:––
––:––
––:––
––
––
––
––
––
––
––
––
(5)
INPUT
––
––
––
––
––
––
––
––
(6)
BRIGHT
––
––
––
––
––
––
––
––
TIPS
OK···[ENTER] CANCEL···[RETURN]
V: 60 Hz H: 67.5 kHz
1. Press
or
to select the SCHEDULE number, and
press
.
2. Set the SCHEDULE. (See the description below.)
or
to select items, and press
Press
change the setting.
or
to
ENTER
.
3. Press
SCHEDULE becomes effective.
(1)
●: SCHEDULE effective
-: SCHEDULE not effective
(2) POWER
ON : Switches the monitor on at the specified time.
OFF: Switches the monitor off at the specified time and puts
the monitor in standby mode.
(3) DAY OF THE WEEK
Specifies the day of the week to execute the SCHEDULE.
0:ONLY ONCE
Executes the SCHEDULE once on the specified day.
Specify the day of the week to execute the SCHEDULE.
1:EVERY WEEK
Executes the SCHEDULE on the specified day of the week
every week. Specify the day of the week to execute the
SCHEDULE.
Periodic setting such as “Monday through Friday” is also
possible.
2:EVERY DAY
Executes the SCHEDULE every day regardless of the day
of the week.
(4) TIME
Specifies the time to execute the SCHEDULE.
Set the time on a 12-hour basis. (Factory default)
Can be entered as 24-hour time using the TIME setting in
DATE/TIME FORMAT.
(5) INPUT
Specifies the input mode at power-on. If you don’t specify
this the input active at the last power-off will appear.
Input modes displayed on HDMI1, HDMI2 and D-SUB will
depend upon the INPUT SELECT settings.
(6) BRIGHT
Sets the brightness when changing the screen brightness at
a specified time.
E
30
• Do not switch off the main power after setting the
SCHEDULE.
• Specify the correct date and time. (See page 24.)
SCHEDULE does not function unless the date and time are
specified.
• Check regularly that the set date and time are correct.
• When STANDBY MODE is LOW POWER, SCHEDULE
cannot be set.
• When a temperature abnormality occurs and the backlight
brightness is reduced, the brightness is not changed even
if a schedule set to BRIGHT is executed.
• Up to 8 SCHEDULE items can be registered.
• Setting the SCHEDULE flashes the power LED alternately
in red and orange in standby mode.
• A SCHEDULE that has a large number has precedence
over that of a small number when schedules overlap.
Menu Items
Adjustments for PC screen display
nAutomatic adjustment
When you use the D-SUB[RGB] or DVI-I (analog) to display a
PC screen for the first time, or when you change the setting of
the PC, use the automatic screen adjustment.
1. Switch the input to D-SUB[RGB] or DVI-I (analog) and
display the adjustment pattern. (See the description
below.)
MENU
2. Press
and use
or
to display the SCREEN
menu.
3. Press
ENTER
and select “AUTO”.
ENTER
.
4. Press
The automatic adjustment is complete in several seconds.
5. Press MENU to close the menu screen.
TIPS
• If the screen cannot be adjusted properly with one
automatic adjustment, repeat the automatic adjustment two
or three times. Try manual adjustment if necessary.
nScreen display for adjustment
Before making adjustments in the SCREEN menu or
PICTURE menu, display an image to brighten the entire
screen. If you are using a Windows PC, use the adjustment
pattern on the supplied CD-ROM.
Opening the adjustment pattern
The following example is performed in Windows 7.
1. Load the supplied CD-ROM into the computer’s CDROM drive.
2. Open [CD Drive] in [Computer].
In Windows XP, open [CD Drive] in [My Computer].
3. Double-click [Adj_uty.exe].
The adjustment pattern will appear.
Adjust the screen automatically or manually.
4. When adjustment is finished, press the [Esc] on the
computer’s keyboard to quit the adjustment program.
5. Eject the CD-ROM from the CD-ROM drive.
TIPS
• If the display mode on the computer you are using is
65,000 colors, the color levels in the color pattern may
appear differently or grayscale may appear to be colored.
(This is due to the specifications of the input signal and is
not a malfunction.)
31
E
Initialization (Reset)/Functional Restriction Setting (FUNCTION)
You can return the settings to their factory-preset values and
restrict operations.
SIZE
down until “F” appears in the upper left
1. Hold
corner of the screen.
,
,
,
in that
2. While “F” appears, press
order.
FUNCTION
▲
▲
▲▲▲▲▲▲
▲
▲▲▲▲▲▲
ALL RESET
OFF
ADJUSTMENT LOCK
ADJUSTMENT LOCK TARGET
UNLOCKED
RS-232C/LAN
ON 1
OSD DISPLAY
ON
LED
TEMPERATURE ALERT
LED
STATUS ALERT
OFF
POWER BUTTON
MONITOR
CONTROLLER INPUT
OK…[ENTER] END…[RETURN]
3. Select and set the items.
ALL RESET
Resets the settings to the factory default settings.
ENTER
, select the resetting method, and then press
Press
ENTER
.
After initialization, turn the main power switch off and
then back on.
ALL RESET1����Resets all the settings to the factory
default settings.
ALL RESET2����Returns all settings to the factory default
settings except for the following items:
LAN SETUP, RS-232C/LAN SELECT,
ID No. SET, BAUD RATE, NETWORK,
MAIL, SERVICE & SUPPORT, and
SNMP (See page 25, and pages 49 to
52.)
ADJUSTMENT LOCK
You can disable operations on the monitor and the
remote control unit that use buttons.
OFF���Enables operation.
ON 1��Disables all operations other than turning power
on/off and FUNCTION.
ON 2��Only the FUNCTION operation is enabled.
Disables all operations other than FUNCTION (not
even power on/off).
ADJUSTMENT LOCK TARGET
Sets the target to prohibit operation of with
ADJUSTMENT LOCK.
REMOTE CONTROL����� Prohibits remote control
operation
MONITOR BUTTONS��� Prohibits monitor switch
operation
BOTH����������������������������� Prohibits remote control and
monitor switch operation
RS-232C/LAN
Specifies whether to allow control via RS-232C or LAN
(see pages 33 and 45).
E
32
OSD DISPLAY
Shows/hides the menu, modes and messages.
The FUNCTION screen cannot be hidden.
ON 1�������������� Shows all menus, modes and messages.
ON 2�������������� Hides messages automatically displayed
by the display. Shows messages during
operation.
OFF��������������� Hides all menus, modes and messages.
LED
Specifies whether to light the power LED.
TEMPERATURE ALERT
Selects the notification method for an abnormal
temperature.
OFF�������������� Do not notify about an abnormal
temperature.
OSD & LED�� When an abnormal temperature is
detected, the power LED flashes in red
and green alternately and the screen
displays a message: TEMPERATURE.
LED�������������� When an abnormal temperature is
detected, the power LED flashes in red
and green alternately.
STATUS ALERT
Selects the notification method for a hardware error.
OFF�������������� Do not notify about the error.
OSD & LED�� When a hardware error is detected, the
power LED flashes in red and the screen
displays a message: STATUS [xxxx].
LED�������������� When a hardware error is detected, the
power LED flashes in red.
POWER BUTTON
Normally, leave this setting as MONITOR.
When using an optional part, if instruction appears,
change the setting accordingly.
CONTROLLER INPUT
Normally, you do not need to change this setting.
When using an optional part, if instruction appears,
change the setting accordingly.
4. Press
RETURN
to return to the normal screen.
TIPS
• When both abnormal temperature and hardware error are
detected, the hardware error notification overrides.
• If TEMPERATURE ALERT or STATUS ALERT is set to
OSD&LED, alert messages will appear even if the OSD
DISPLAY is set to ON 2 or OFF.
• If TEMPERATURE ALERT or STATUS ALERT is set to LED
or OSD & LED, the LED lights even if the LED function is
set to OFF.
Controlling the Monitor with a PC (RS-232C)
You can control this monitor from a PC via RS-232C (COM
port) on the PC.
You can also connect multiple monitors via a daisy chain by
using a PC. By assigning ID numbers to each monitor (see
page 34), you can make input mode selection/adjustment or
can check the status of a specific monitor.
TIPS
• To control the monitor via RS-232C, set RS-232C/LAN
SELECT to RS-232C.
• You cannot use RS-232C and LAN control simultaneously.
PC connection
Communication conditions
Set the RS-232C communication settings on the PC to match
the monitor’s communication settings as follows:
Baud rate
*
Stop bit
1 bit
Data length
8 bits
Flow control
None
Parity bit
None
* Set to the same baud rate as the BAUD RATE setting of
SETUP menu. (Initial setting: 38400 bps)
* When connecting multiple monitors in a daisy chain, set all
monitors to the same BAUD RATE.
nOne-to-one connection with a PC
Communication procedure
Connect with RS-232 straight cable between the PC’s COM
port (RS-232C connector) and the RS-232C input terminal on
the monitor.
nCommand format
When a command is sent from the PC to the monitor, the
monitor operates according to the received command and
sends a response message to the PC.
Return code
RS-232C input terminal
C1
PC
C2
C3
C4
P1
Command field
(4 prescribed
alphanumerical characters)
To COM port
RS-232 straight cable
(commercially available)
P2
P3
P4
Parameter field
(4 character string comprised of:
0-9, +, -, space, ?)
Example: VOLM0030
VOLM
30
nDaisy chain connection… Advanced operation
Connect with RS-232 straight cable between the PC’s COM
port (RS-232C connector) and the RS-232C input terminal on
the first monitor.
Next, connect RS-232 straight cable to the first monitor’s
RS‑232C output terminal and to the second monitor’s
RS-232C input terminal. Connect in the same way to the third
and subsequent monitors.
Up to 25 monitors can be connected. (Depending on the
length of the cable used and the surrounding environment.)
Second monitor
* Be sure to input 4 characters for the parameter. Pad with
spaces (“ ”) if necessary.
(“
” is a return code (0DH, 0AH or 0DH))
Wrong : VOLM30
Right : VOLM
30
When inputting a negative value, specify a numerical value in
three digits.
Example: AUTR-005
Do not use spaces for MPOS, DATE, and SC01 through
SC08. Specify parameters using a specified number of
characters.
RS-232C
output terminal
RS-232 straight cables
(commercially available)
First monitor
PC
To COM port
RS-232C
input terminal
Example: MPOS010097
If a command has “R” listed for “DIRECTION” in the
“RS-232C command table” on page 37, the current value can
be returned by using “?” as the parameter.
Example:
VOLM ? ? ? ?
←
From PC to monitor (How much
is current volume setting?).
30
←
From monitor to PC (Current
volume setting: 30).
* If an ID number (see page 34) has been assigned
(For example, ID number = 1).
VOLM
30
001
?
← From PC to monitor.
← From monitor to PC.
33
E
Controlling the Monitor with a PC (RS-232C)
nResponse code format
nCommunication interval
When a command has been executed correctly
• After OK or ERR is returned, you must send the following
commands.
To set a timeout for the command response, specify 10
seconds or longer.
When connecting multiple monitors in a daisy chain, set the
timeout to at least the product of the monitor’s position from
the computer multiplied by 10 seconds.
Example) 3rd monitor from computer: 30 seconds or longer.
• Provide an interval of 100 ms or more between the
command response and the transmission of the next
command.
O
K
Return code
(0DH, 0AH)
A response is returned after a command is executed.
* If an ID number has been assigned
Return code
(0DH, 0AH)
Space (20H)
O
K
SPC
0
0
1
ID number of responding monitor
VOLM0020
OK
When a command has not been executed
E
R
R
Interval of 100 ms or more
Return code
(0DH, 0AH)
INPS0001
WAIT
OK
* If an ID number has been assigned
Return code
(0DH, 0AH)
Space (20H)
E
R
R
SPC
0
0
1
TIPS
ID number
TIPS
• “ERR” is returned when there is no relevant command or
when the command cannot be used in the current state of
the monitor.
• If communication has not been established for reasons
such as a bad connection between the PC and monitor,
nothing is returned (not even ERR).
• “ERR” may be returned when a command cannot be
received correctly due to interference from the surrounding
environment.
Please ensure that the system or software retries the
command if this occurs.
• If no monitor has been assigned the designated ID number
(e.g. if the command IDSL0002
is used, but no monitor
with ID number: 2 is found), no response is returned.
If execution of the command is taking some time
W
A
I
T
When control via RS-232C is locked (to prevent use)
using the operation lock function (see page 33)
O
C
K
E
D
Return code
(0DH, 0AH)
When RS-232C/LAN SELECT is set to LAN
U
E
34
N
S
E
L
E
C
T
E
Advanced operation
This section explains commands for daisy chain connection.
The basic communication procedure is the same as in the
“One-to-one connection with a PC” section.
nID numbers
You can assign a unique ID number to each monitor (see
page 25). This allows you to control a particular monitor in a
daisy chain of monitors.
You can assign ID numbers either from the menu screen or
from the PC using RS-232 cable.
[Example]
ID number: 1
Return code
(0DH, 0AH)
When the following commands are used, “WAIT” is returned.
In this case, a value will be returned if you wait a while. Do not
send any command during this period.
No ID number is attached to WAIT response.
• Commands which return WAIT:
1. When repeater control is used
2. When an IDSL or IDLK command is used
3. When one of the following commands is used: RSET,
INPS, ASNC, WIDE, EMAG, EPOS, PXSL, POWR,
AGIN, MWIN, MWIP, MWPP, ESTG, EMHV, EPHV,
ESHV, ENLG
L
• When executing ALL RESET, set the timeout period to 30
seconds or longer.
• When turning the power on while the POWER ON DELAY
function is in use, set the timeout period to the POWER ON
DELAY period + 10 seconds or longer.
D
Return code
(0DH, 0AH)
ID number: 2
ID number: 3 ID number: 4
If monitors are connected as shown above, you can
execute commands like “Set the volume of the monitor with
ID 4 to 20”.
When designating ID numbers for a set of monitors linked in a
daisy chain, you should basically avoid any duplication of ID
numbers.
ID numbers do not have to be assigned in ascending order
starting from the PC. They can also be connected as shown
below.
[Example]
ID number: 3
ID number: 2 ID number: 4 ID number: 1
Controlling the Monitor with a PC (RS-232C)
nCommands for ID control
The command examples shown on this page assume the
following connection and ID number set up.
ID number: 1
ID number: 2 ID number: 3
ID number: 4
IDST��������.A monitor receiving this command sets its own ID
number in the parameter field.
Example:
IDST0001
001 ← The ID number of this monitor is set to 1.
OK
IDLK��������The parameter of this command sets the ID
number of the monitor. The monitor is subject to all
subsequent commands.
Example:
← with ID number: 2.
WAIT
←
OK
002
Searching for monitor with ID number:
2
← Found monitor with ID number: 2
Sets volume of monitor with ID
VOLM0030
← number: 2 to 30.*
WAIT
← Processing
OK
002
VOLM0020
TIPS
Following commands are for the monitor
IDLK0002
Sets volume of monitor with ID
← number: 2 to 20.*
WAIT
You can automatically assign ID numbers by using the IDST
command with the Repeater control (see “Repeater control”
on page 36).
For example, using the command “IDST001+” automatically
sets the ID numbers, as shown below.
[Example]
ID number: 1
ID number: 2 ID number: 3
ID number: 4
OK
IDLK0000
← Canceling fixed ID number setting
WAIT
← Canceling IDLK
OK
← ID setting command with repeater control
WAIT
OK
001
← “OK” response from ID number: 1
OK
002
← “OK” response from ID number: 2
OK
003
← “OK” response from ID number: 3
OK
004
← “OK” response from ID number: 4 (End)
IDSL��������The parameter of this command sets the ID number
of the monitor. The monitor is subject to the next
command.
002
← Cancelation complete
VOLM0010
OK
IDST001 +
002
001
The volume of the monitor with ID number:
← 1 (the one directly connected to the PC) is
set to 10. (IDLK is canceled.)
* The IDLK command remains effective until it is
canceled, or power is shut off.
IDCK��������Provides screen display of the ID number currently
assigned to a monitor, and the ID number currently
set for IDLK (if any).
Example:
(After executing IDLK0002)
← (Parameter has no meaning.)
IDCK0000
ID : 001
IDLK : 002
Returned response. The ID
← number is also displayed on the
monitor screen.
Example:
IDSL0002
←
The next command is for the monitor
with ID number: 2.
WAIT
←
Searching for monitor with ID number:
2
OK
002
← Found monitor with ID number: 2
Sets volume of monitor with ID
number: 2 to 30.
VOLM0030
←
WAIT
← Processing
OK
002
VOLM0020
OK
001
IDCK000 +
WAIT
ID : 001
IDLK : 000
ID : 002
IDLK : 000
ID : 003
IDLK : 000
ID : 004
IDLK : 000
← Repeater control. (If a command
is used with repeater control, ID
designation using IDSL or IDLK
is canceled.)
OK response from monitor with ID
← number: 2
← Sets volume to 20.
The volume of the monitor with ID
← number: 1 (the one directly connected
to the PC) is set to 20.*
* The IDSL command is effective only once, for the
immediately succeeding command.
35
E
Controlling the Monitor with a PC (RS-232C)
nRepeater control
This system has a function to allow setting of multiple
monitors connected in a daisy chain using a single command.
This function is called repeater control. You can use Repeater
control function without assigning ID numbers.
[Example]
Set 1
Set 2
Set 3
Set 4
Setting of the GAMMA user data
nTo transfer the GAMMA user data
Use the user data transfer commands (UGRW, UGGW and
UGBW). For each of the R, G and B colors, divide the total
512 pieces of user data into 16 blocks, and transfer 32 pieces
of data with each command.
C1
C2
C3
Command field
* If monitors are connected as shown above, you can
execute a command like “Set all monitors’ input settings to
D-SUB[RGB]”.
C4
P1
P2
P3
P4
…
Block number (01 to 16) Data field
S1
S2
Checksum field
xample: To transfer the data of block 1 (0 to 31 levels)
E
of red (R) data
UGRW 01000000010002 … 0031C0
nRepeater control command
One piece of data consists
of 4 digits.
Repeater control is achieved by setting the FOURTH
CHARACTER of the parameter to “+”.
Command Block number
32 pieces of data
Checksum
Example:
VOLM030 +
← Sets volume of all monitors to 30.
In repeater control, responses are returned by all the
connected monitors.
If you want to determine that a value has been returned by a
specific set, assign ID numbers to each monitor in advance.
When some monitors do not return their responses, the
probable cause is that the monitors could not receive the
command or command processing is not complete. Do not
send a new command.
Example: (When 4 monitors are connected, and
assigned ID numbers: 1 through 4)
VOLM030 +
001
OK
002
OK
003
OK
004
nSaving the GAMMA user data
Use the user data save command (UGSV) to save the
transferred user data in the monitor.
If the data is not saved, it will be cleared when:
• The main power switch is off
• STANDBY MODE is LOW POWER and the monitor enters
standby mode
nActivating the GAMMA user data
WAIT
OK
* If data is less than 4 digits, add a “0” (zero) to make it 4
digits.
* The checksum field is the character string (ASCII) data of
lower-order one byte which indicates the sum of the block
number and 32 pieces of data in hexadecimal (0 to F).
To activate the transferred user data, select USER for GAMMA
of the PICTURE menu, or send the corresponding RS-232C
command.
← If 4 monitors are connected in
a chain, reliable operation can
be ensured by sending a new
command only after a reply
has been returned by 4th (last)
monitor.
Repeater control can also be used for reading settings.
nChecking the GAMMA user data
Use the user data read commands (UGRR, UGGR and
UGBR) to return 512 pieces of user data for each of the R,
G and B colors. Divide the data into 16 blocks and return 32
pieces of data with each command. The value to be returned
is not the value stored in the monitor, but the value in the
temporary memory for display. (These values are the same
when the user data save command (UGSV) above has been
sent.)
Example:
TIPS
VOLM ? ? ? +
WAIT
10
001
20
002
30
003
30
004
Volume settings for all
monitors are returned.
TIPS
• If repeater control is used during ID designation (IDSL,
IDLK), the ID designation is canceled.
E
36
• The user data is not initialized by RESET of the PICTURE
menu. To initialize the user data, use ALL RESET of the
FUNCTION menu.
The GAMMA user data initialize command (UGRS) allows
the initialization of the user data only.
Controlling the Monitor with a PC (RS-232C)
RS-232C command table
How to read the command table
Command:
Command field (See page 33.)
Direction:
W When the “Parameter” is set in the parameter field (see page 33), the command functions as described
under “Control/Response Contents”.
R The returned value indicated under “Reply” can be obtained by setting “????”, “
?” or “???+”
(repeater control) in the parameter field (see page 33).
Parameter:
Parameter field (See page 33.)
Reply:
Response (Returned value)
* :
“●” indicates a command which can be used in power standby mode regardless of the STANDBY MODE setting.
“○” indicates a command which cannot be used in power standby mode when STANDBY MODE is set to LOW POWER.
“–” indicates a command which cannot be used in power standby mode regardless of the STANDBY MODE setting.
Power control/Input mode selection
Function
POWER CONTROL
Command
Direction
POWR
W
Parameter
Reply
0
1
Control/Response contents
Returns from standby mode.
0 Standby mode
R
*
Switches to standby mode.
1 Normal mode
●
2 Input signal waiting mode
INPUT MODE SELECTION
INPS
W
0
Toggle change for input mode. Terminals not selected in INPUT SELECT cannot
be selected.
1
DVI-I
2
D-SUB[RGB]
“ERR” when other than RGB is selected for D-SUB of INPUT SELECT.
3
D-SUB[COMPONENT]
“ERR” when other than COMPONENT is selected for D-SUB of INPUT SELECT.
4
D-SUB[VIDEO]
“ERR” when other than VIDEO is selected for D-SUB of INPUT SELECT.
9
HDMI1[AV]
“ERR” when PC is selected for HDMI1 of INPUT SELECT.
10
HDMI1[PC]
“ERR” when AV is selected for HDMI1 of INPUT SELECT.
12
HDMI2[AV]
“ERR” when PC is selected for HDMI2 of INPUT SELECT.
13
HDMI2[PC]
“ERR” when AV is selected for HDMI2 of INPUT SELECT.
14
R
●
DisplayPort
1 DVI-I
2 D-SUB[RGB]
3 D-SUB[COMPONENT]
4 D-SUB[VIDEO]
9 HDMI1[AV]
10 HDMI1[PC]
●
12 HDMI2[AV]
13 HDMI2[PC]
14 DisplayPort
37
E
Controlling the Monitor with a PC (RS-232C)
SCREEN menu
Command
Direction
Auto
Function
ASNC
W
CLOCK
CLCK
WR
size
RESOLUTION
Reply
Control/Response contents
1
When the input mode is D-SUB[RGB], DVI-I (analog).
0-1200
0-1200 When the input mode is D-SUB[RGB], DVI-I (analog).
Varies depending on the signal.
PHSE
WR
0-63
Position of
the longest
direction
HPOS
WR
0-100
0-100 0-800 on D-SUB[RGB], DVI-I (analog).
Varies depending on the signal.
Position of
the shortest
direction
VPOS
WR
0-100
0-100 0-200 on D-SUB[RGB], DVI-I (analog).
Varies depending on the signal.
SIZE of the
longest
direction
HSIZ
WR
0-100
0-100
SIZE of the
shortest
direction
VSIZ
WR
0-100
0-100
Longest
direction
resolution
HRES
WR
300-1920
300-1920 When the input mode is D-SUB[RGB], DVI-I (analog).
Only even numbers are valid for parameters.
Varies depending on the signal.
Shortest
direction
resolution
VRES
WR
200-1200
200-1200
ARST
W
PHASE
positioning
Parameter
RESET
*
0-63 When the input mode is D-SUB[RGB], DVI-I (analog).
-
1
PICTURE menu
Command
Direction
BRIGHT
Function
VLMP
WR
0-31
0-31
CONTRAST
CONT
WR
0-60
0-60
BLACK LEVEL
BLVL
WR
0-60
0-60
TINT
TINT
WR
0-60
0-60
COLORS
COLR
WR
0-60
0-60
SHARPNESS
SHRP
WR
0-24
0-24
BMOD
WR
0
0 STD
2
2 VIVID
3
3 sRGB (When the input mode is PC)
COLOR
ADJUSTMENT
COLOR MODE
WHITE
BALANCE
THRU
CTMP
WR
Parameter
USER
4 HIGH ILLUMINANCE
0 PC input
99
99
CRTR
WR
0-256
0-256 “ERR” when CTMP is not set to 99.
G-CONTRAST
CRTG
WR
0-256
0-256
B-CONTRAST
CRTB
WR
0-256
0-256
R-OFFSET
OFSR
WR
-127-127
-127-127
G-OFFSET
OFSG
WR
-127-127
-127-127
B-OFFSET
OFSB
WR
-127-127
-127-127
COPY TO USER
CPTU
W
GAMMA
GAMM
WR
0-2 0: 1.8, 1: 2.2, 2: 2.4 (during PC input)
0: LIGHT 2, 2: DARK (during AV input)
4-6
4-6 4: USER, 5: 2.0, 6: STD (during PC input)
4: USER, 5: LIGHT 1, 6: STD (during AV input)
FLES
WR
0-2
C.M.S.-HUE (AV input)
CMHR
WR
-10-10
-
0-2 0: OFF, 1: LOW, 2: HIGH
Y
CMHG
G
CMHC
C
CMHB
B
M
CRST
W
CMSR
WR
1
-10-10
Resets the hue.
-10-10 R
CMSY
Y
CMSG
G
CMSC
C
CMSB
B
M
CRST
W
CMVR
WR
2
-10-10
Resets the saturation.
-10-10 R
CMVY
Y
CMVG
G
CMVC
C
CMVB
B
CMVM
CRST
○
-10-10 R
CMHY
CMSM
C.M.S.-VALUE (AV input)
Copies a preset value to the user setting.
0-2
FLESH TONE (AV input)
C.M.S.-SATURATION
(AV input)
38
1-18 From 1: approximately 3,000K to 15: approximately 10,000K (500K steps)
16: approximately 5,600K, 17: approximately 9,300K, 18: approximately 3,200K
R-CONTRAST
0
*
○
0
CMHM
E
Control/Response contents
4
1-18
PRESET
Reply
M
W
3
Resets the brightness.
○
Controlling the Monitor with a PC (RS-232C)
ADVANCED
Function
Command
Direction
AUTO
AGIN
W
ANALOG GAIN
ANGA
ANALOG OFFSET
3D-NR (AV input)
Parameter
Reply
Control/Response contents
1
When the input mode is D-SUB[RGB], DVI-I (analog).
WR
0-127
0-127 When the input mode is D-SUB[RGB], DVI-I (analog).
ANOF
WR
0-127
0-127 When the input mode is D-SUB[RGB], DVI-I (analog).
TDNR
WR
0-2
0-2 0: OFF, 1: LOW, 2: HIGH
MPEG-NR (AV input)
MPNR
WR
0-1
0-1 0: OFF, 1: ON
3D-Y/C
YCSP
WR
0-1
0-1 0: OFF, 1: ON (When the input mode is D-SUB[VIDEO])
RGB INPUT RANGE
(HDMI1[AV])
AHDR
WR
0-2
0-2 0: AUTO, 1: FULL, 2: LIMITED
RGB INPUT RANGE
(HDMI1[PC])
PHDR
WR
0-2
0-2 0: AUTO, 1: FULL, 2: LIMITED
RGB INPUT RANGE
(HDMI2[AV])
AH2R
WR
0-2
0-2 0: AUTO, 1: FULL, 2: LIMITED
RGB INPUT RANGE
(HDMI2[PC])
PH2R
WR
0-2
0-2 0: AUTO, 1: FULL, 2: LIMITED
RGB INPUT RANGE
(DVI-I)
PDVR
WR
1-2
1-2 1: FULL, 2: LIMITED
RGB INPUT RANGE
(D-SUB)
PDSR
WR
1-2
1-2 1: FULL, 2: LIMITED
RGB INPUT RANGE
(DisplayPort)
PDPR
WR
0-2
0-2 0: AUTO, 1: FULL, 2: LIMITED
ACTIVE CONTRAST (AV input)
ACNT
WR
0-1
0-1 0: OFF, 1: ON
DISPLAY COLOR PATTERN
PTDF
WR
0
0 No pattern display.
1
1 White single color pattern display.
2 Red single color pattern display.
3
3 Green single color pattern display.
4 Blue single color pattern display.
4
99 Red/green/blue mixed color pattern display.
Set each color's level with RED, GREEN, BLUE.
DISPLAY COLOR PATTERN (R) PTDR
WR
0-15
0-15 “ERR” when PTDF is not set to 99.
DISPLAY COLOR PATTERN (G) PTDG
WR
0-15
0-15
DISPLAY COLOR PATTERN (B) PTDB
WR
0-15
0-15
ARST
W
-
○
2
99
RESET
*
2
-
AUDIO menu
Command
Direction
TREBLE
Function
AUTR
WR
Parameter
Reply
BASS
AUBS
WR
-5-5
-5-5
BALANCE
AUBL
WR
-10-10
-10-10
RESET
ARST
W
-5-5
3
Control/Response contents
*
-5-5
○
-
39
E
Controlling the Monitor with a PC (RS-232C)
SETUP menu
Command
Direction
Date/time setting
Function
DATE
WR
DATE DISPLAY FORMAT
DTFT
WR
TIME DISPLAY FORMAT
TMFT
WR
SCHEDULE
SC01SC08
WR
SCHEDULE BRIGHTNESS
LANGUAGE
SB01SB08
WR
LANG
WR
Parameter
Reply
AABBCCDDEE
0-2
0-1
ABCDEFFGGH
0-1 0: 24-HOUR TIME, 1: 12-HOUR TIME
AUDIO SELECT
AUDIO OPTION
COMMUNICATION
SETTING
ID SETTING
0-31
99 Disable brightness setting
14
14 ENGLISH
1
1 DEUTSCH
2
2 FRANÇAIS
3
3 ITALIANO
4
4 ESPAÑOL
5
5 РУССКИЙ
6
HDSL
WR
0-1
0-1 0:PC 1:AV
HDMI2
H2SL
WR
0-1
0-1 0:PC 1:AV
D-SUB
SLDS
WR
0-2
0-2 0:RGB 1:COMPONENT 2:VIDEO
HDMI1 AUTO VIEW HDAW
WR
0-1
0-1 0: OFF, 1: ON
HDMI2 AUTO VIEW H2AW
WR
0-1
0-1 0: OFF, 1: ON
HOT PLUG
CONTROL (DVI-I)
HPCT
WR
0-1
0-1 0: OFF, 1: ON
HOT PLUG
HPCH
CONTROL (HDMI1)
WR
0-1
0-1 0: OFF, 1: ON
HOT PLUG
HPH2
CONTROL (HDMI2)
WR
0-1
0-1 0: OFF, 1: ON
EDID SELECT
(DVI-I)
WR
0-2
0-2 0: AUTO, 1: DIGITAL, 2: ANALOG
DVI-I
ASDP
WR
1-2
1-2 1: AUDIO1, 2: AUDIO2
D-SUB[RGB]
ASAP
WR
1-2
1-2 1: AUDIO1, 2: AUDIO2
HDMI1[PC]
ASHP
WR
0-2
0-2 0: HDMI, 1: AUDIO1, 2: AUDIO2
HDMI1[AV]
ASHA
WR
0-2
0-2 0: HDMI, 1: AUDIO1, 2: AUDIO2
HDMI2[PC]
AH2P
WR
0-2
0-2 0: HDMI, 1: AUDIO1, 2: AUDIO2
HDMI2[AV]
AH2A
WR
0-2
0-2 0: HDMI, 1: AUDIO1, 2: AUDIO2
D-SUB[COMPONENT]
ASC2
WR
1-2
1-2 1: AUDIO1, 2: AUDIO2
D-SUB[VIDEO]
ASV2
WR
1-2
1-2 1: AUDIO1, 2: AUDIO2
DisplayPort
ASDI
WR
1-3
1-3 1: AUDIO1, 2: AUDIO2, 3: DisplayPort
AUDIO OUTPUT
AOUT
WR
0-2
0-2 0: VARIABLE1, 1: FIXED, 2: VARIABLE2
AUDIO INPUT
LEVEL1
AIVP
WR
0-1
0-1 0: 1.0Vrms, 1: 0.5Vrms
AUDIO INPUT
LEVEL2
AIV2
WR
0-1
0-1 0: 1.0Vrms, 1: 0.5Vrms
MONAURAL
AUDIO
MONO
WR
0-1
0-1 0: OFF, 1: ON
RS-232C/LAN
SELECT
CTLS
WR
0-1
0-1 0: RS-232C 1: LAN
BAUD RATE
BAUD
WR
0-2
0-2 0: 9600bps, 1: 19200bps, 2: 38400bps
ID NO.SETTING
IDST
W
0-255
IDSL
W
1-255
ID NO. SETTING
(SUBSEQUENT)
IDLK
W
1-255
ID CHECK
IDCK
W
0
ID DISPLAY
IDDP
W
0-2
SETTING COPY
MODE
CPMD
WR
SETTING COPY
TARGET
CPTG
WR
E
40
○
○
Returns the monitor’s ID number.
Clears the ID number if one has been designated.
Sets a monitor ID number.
This ID number is effective for the next and all subsequent commands after this
command.
0
1-255
○
Sets a monitor ID number.
This ID number is only effective for the command immediately after this
command.
0
0
○
Sets the monitor’s ID number. (“0” means “no ID number”.)
0-255
ID NO. SETTING
(ONCE)
○
0-31 Screen brightness to change
99
R
COPY SETTING
VALUE
Schedule of a specified number
A: Schedule
0= Not effective, 1 = Effective
B: Power
0 = OFF, 1 = ON
C: Day of the week 1 0 = Only once, 1 = Every week, 2 = Every day
D: Day of the week 2 0 = Sunday, 1 = Monday through 6 = Saturday,
9 = Not exist
E: Day of the week 3 0 = Sunday, 1 = Monday through 6 = Saturday,
9 = Not exist
F: Hour
00-23
G: Minute
00-59
H: Input
0 = Not specified, 1 = DVI-I, 2 = DisplayPort,
3 = HDMI1, 4 = HDMI2, 5 = D-SUB
“ERR” when LOW POWER is selected for STANDBY MODE.
ABCDEFFGGH
HDMI1
DVED
*
0-2 0: YYYY/MM/DD, 1: MM/DD/YYYY, 2: DD/MM/YYYY
YYYY: Year, MM: Month, DD: Day
6
INPUT SELECT
Control/Response contents
AA: Year, BB: Month, CC: Day, DD: Hour, EE: Minute
AABBCCDDEE
○
Clears the ID number if one has been designated.
ID
: xxx
IDLK : yyy
Displays monitor’s own ID number and the selected ID number on the screen.
0: OFF, 1: ON, 2: ON (turns OFF after 4 sec.)
(The IP address and MAC address are both displayed.)
-
0 Copy to all monitors.
1-255 Copy to the monitor with the set ID Number.
0
0 Copies the PICTURE menu settings.
1
1 Copies all the settings.
○
Controlling the Monitor with a PC (RS-232C)
MONITOR menu
Command
Direction
MONITOR
Function
STDR
WR
Parameter
0-1
Reply
0-1
Control/Response contents
OSD H-POSITION
OSDH
WR
0-100
0-100
OSD V-POSITION
OSDV
WR
0-100
0-100
STANDBY MODE
STBM
WR
0-1
0-1
0: STANDARD, 1: LOW POWER
(“ERR" when SCHEDULE is effective.)
OFF IF NO OPERATION
ATOF
WR
0-1
0-1
0: OFF, 1: ON
POWER ON
DELAY
SET
PODS
WR
0-1
0-1
0: OFF, 1: ON
INTERVAL
PWOD
WR
0-60
0-60
SELF ADJUST
SELF ADJUST
AADJ
WR
0-1
0-1
START TIMING
AADD
WR
10-200
10-200
*
0: LANDSCAPE, 1: PORTRAIT
○
0: OFF, 1-60 seconds
0: OFF, 1: ON
10: 1 second through 200: 20 seconds
41
E
Controlling the Monitor with a PC (RS-232C)
MULTI/PIP menu
Command
Direction
ENLARGE
Function
ENLG
WR
Parameter
Reply
Control/Response contents
ENLARGE MODE
EMAG
WR
0-4
EMHV
WR
11-55
11-55 1 x 1 (OFF) to 5 x 5 (“m x n” is expressed as “mn”, where m and n are the
numbers of monitors specified for the longest direction and the shortest direction
respectively.)
IMAGE POSITION (M x N)
EPHV
WR
11-55
11-55 Specifies values in the order of IMAGE POSITION IN LONGEST/ SHORTEST
DIRECTION.
IMAGE POSITION (2 x 2)
EPOS
WR
0-3
IMAGE POSITION (3 x 3)
EPOS
WR
0-8
0-8
IMAGE POSITION (4 x 4)
EPOS
WR
0-15
0-15
IMAGE POSITION (5 x 5)
0-1
*
0-1 0: OFF, 1: ON
0-4 0: OFF, 1: 2 x 2, 2: 3 x 3, 3: 4 x 4, 4: 5 x 5
0-3 See the description below.
EPOS
WR
0-24
The longest
direction
EPSH
WR
-999-999
-999-999 The setting range depends on the ENLARGE MODE setting and the IMAGE
POSITION.
The shortest
direction
EPSV
WR
-999-999
-999-999
BZCO
WR
0-1
0-1 0: OFF, 1: ON
TOP
BZCT
WR
0-1
0-1 0: OFF, 1: ON
BOTTOM
BZCB
WR
0-1
0-1 0: OFF, 1: ON
RIGHT
BZCR
WR
0-1
0-1 0: OFF, 1: ON
LEFT
BZCL
WR
0-1
TOP
BZWT
WR
0-100
0-100
BOTTOM
BZWB
WR
0-100
0-100
RIGHT
BZWR
WR
0-100
0-100
LEFT
BZWL
WR
0-100
0-100
ENLARGE/IMAGE POSITION SETTING ESTG
WR
XXYY
XXYY XX: ENLARGE MODE (Same as EMAG), YY: IMAGE POSITION (Same as
EPOS)
ESHV
WR
XXYY
XXYY XX: ENLARGE MODE (Same as EMHV), YY: IMAGE POSITION (Same as
EPHV)
ENLARGED
SCREEN
POSITIONING
-
BEZEL ADJUST
BEZEL ADJUST
BEZEL WIDTH
0-24
0-1 0: OFF, 1: ON
• IMAGE POSITION (EPOS) setting
In landscape orientation
2x2
3x3
4x4
5x5
0
1
0
1
2
0
2
3
3
4
5
4
5
6
7
5
6
7
8
9
6
7
8
8
9
10
11
10
11
12
13
14
13
14
15
16
17
18
19
20
21
22
23
24
1
12
2
3
0
15
1
3
2
In portrait orientation
2x2
1
3
0
2
3x3
4x4
2
5
8
1
4
7
0
3
6
3
2
1
0
E
42
5x5
15
7
11
6
10
14
5
9
13
4
8
12
4
9
14
19
24
3
8
13
18
23
7
12
17
1
6
11
16
21
0
5
10
15
20
2
22
4
Controlling the Monitor with a PC (RS-232C)
Function
PIP MODES
PIP SIZE
PIP POS
Command
Direction
MWIN
WR
MPSZ
WR
The longest
direction
MHPS
W
The shortest
direction
MVPS
W
MPOS
W
PIP POS LD+SD BATCH
Parameter
Reply
0-3
Control/Response contents
*
0-3 0: OFF, 1: PIP, 2: PbyP, 3: PbyP2
1-64
1-64
0-100
0-100
R
0-100
0-100
R
0-100,0-100
Specify the position in MPOSxxxyyy format.
(xxx: Longer side, yyy: Shorter side position)
0-100,0-100 Returns a response in (xxx,yyy) format.
(xxx: Longer side, yyy: Shorter side position)
R
PIP BLEND
MWBL
WR
0-15
PIP SOURCE
MWIP
WR
1
0-15
1 DVI-I
2
2 D-SUB[RGB]
3
3 D-SUB[COMPONENT]
4
4 D-SUB[VIDEO]
9
9 HDMI1[AV]
10
10 HDMI1[PC]
12
12 HDMI2[AV]
13
13 HDMI2[PC]
14
○
14 DisplayPort
SOUND CHANGE
MWAD
WR
1-2
1-2 1: MAIN, 2: SUB
MAIN POS (Main screen)
MWPP
WR
0-1
0-1 0: POS1, 1: POS2
PbyP2 POS (Sub screen)
MW2P
WR
0-2
0-2 0: POS1, 1: POS2, 2: POS3
AUTO OFF
MOFF
WR
0-1
0-1 0: MANUAL, 1: AUTO
OTHERS menu
Function
Command
Direction
PATTERN
SCSV
WR
MOTION TIME1
MTIM
WR
0-20
MOTION TIME2
(PATTERN1)
MINT
WR
10-990
MOTION TIME2
(PATTERN2-4)
MINT
WR
5-20
POWER MANAGEMENT (PC)
PMNG
WR
0-1
0-1 0: OFF, 1: ON
POWER MANAGEMENT (AV)
PMAV
WR
0-1
0-1 0: OFF, 1: ON
AUTO INPUT CHANGE
AINC
WR
0-1
0-1 0: OFF, 1: ON
LOGO SCREEN
BTSC
WR
0-1
0-1 0: OFF, 1: ON
RESOLUTION CHECK
PXCK
R
PIXEL SETTING
(D-SUB[RGB],
DVI-I(analog))
PXSL
WR
SCREEN MOTION
INPUT
RESOLUTION
(PC)
INPUT RESOLUTION (AV)
RESOLUTION CHECK
Parameter
Reply
0-4
Control/Response contents
*
0-4 0: OFF, 1-4: PATTERN1-4
0-20
10-990 Per 10 seconds
5-20 Per second
○
- Returns current resolution in the form of hhh, vvv.
1
1 768) 1360 x 768
2
2 768) 1280 x 768
3
3 768) 1024 x 768
5
5 480) 848 x 480
6
6 480) 640 x 480
7
7 1050) 1680 x 1050
8
8 1050) 1400 x 1050
9
9 768) AUTO
10
10 480) AUTO
-
- 480i, 480p, 1080i, 720p, 1080p, VGA , etc.
RESO
R
ZOOM2 SPECIAL SETTING
(D-SUB[RGB], DVI-I(analog))
Z2SP
WR
0-1
0-1 0: OFF, 1: ON
SCAN MODE
SCAN
WR
0-2
0-2 0: MODE1, 1: MODE2, 2: MODE3 (When the input mode is AV)
COLOR SYSTEM
CSYS
WR
0-5
0-5 0: AUTO, 1: PAL, 2: PAL-60, 3: SECAM, 4: NTSC3.58, 5: NTSC4.43
○
43
E
Controlling the Monitor with a PC (RS-232C)
Initialization/Functional Restriction Setting (FUNCTION) menu
Command
Direction
ALL RESET
Function
RSET
W
Parameter
0-1
Reply
Control/Response contents
ADJUSTMENT LOCK
ALCK
WR
0-2
0-2 0: OFF, 1:ON1, 2:ON2
ADJUSTMENT LOCK TARGET
ALTG
WR
0-2
0-2 0: REMOTE CONTROL, 1: MONITOR BUTTONS, 2: BOTH
OSD DISPLAY
LOSD
WR
0-2
0-2 0: ON1, 1: OFF, 2: ON2
LED
OFLD
WR
0-1
0-1 0: ON, 1: OFF
TEMPERATURE ALERT
TALT
WR
0-2
0-2 0: OFF, 1: OSD & LED, 2: LED
POWER BUTTON
PBTN
WR
0-1
0-1 0: MONITOR, 1: CONTROLLER
CONTROLLER INPUT
PCIP
WR
0-4
0-4 0: D-SUB, 1: DisplayPort, 2: HDMI1, 3: HDMI2, 4: DVI-I
(”ERR” when MONITOR is selected for POWER BUTTON.)
STATUS ALERT
SALT
WR
0-2
0-2 0: OFF, 1: OSD & LED, 2: LED
0: ALL RESET 1, 1: ALL RESET 2
*
-
○
Others
Command
Direction
SCREEN SIZE (PC)
Function
WIDE
WR
SCREEN SIZE (AV)
WIDE
WR
1-5
VOLUME
VOLM
WR
0-31
0-1
MUTE
INFORMATION
Parameter
Reply
1-5
Control/Response contents
1-5 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2
1-5 1: WIDE, 2: ZOOM1, 3: ZOOM2, 4: NORMAL, 5: Dot by Dot
0-31
0-1 0: OFF, 1: ON
MUTE
WR
MODEL
INF1
R
Value
SERIAL NO
SRNO
R
Value
DSTA
R
TEMPERATURE SENSOR
*
○
-
●
0 Internal temperature normal
1 Internal temperature abnormal has occurred and the monitor is in standby mode
2 Internal temperature abnormal occurred (To delete the information of temperature
abnormal, turn off the main power.)
●
3 Internal temperature abnormal has occurred and backlight brightness is dimmed
4 Temperature sensor abnormal
Temperature acquisition
CAUSE OF LAST STANDBY MODE
ERRT
STCA
Value Temperature at temperature sensors 1 through 6 are returned in the following
forms:
[Sensor 1], [Sensor 2], [Sensor 3], [Sensor 4], [Sensor 5], [Sensor 6]
Indicates a temperature sensor abnormality when “126” is returned.
R
0
W
○
Initialization
0 No detectable error has occurred
R
1 Standby mode by POWER button
2 Main power off by the main power switch
3 Standby mode by RS-232C or LAN
4 Input signal waiting mode by No Signal
●
6 Standby mode by abnormal temperature
8 Standby mode by SCHEDULE setting
20 Standby mode by OFF IF NO OPERATION setting
Commands for setting of the GAMMA user data
Function
E
Command
Direction
RED GAMMA DATA TRANSFER
UGRW
W
GREEN GAMMA DATA TRANSFER
UGGW
W
BLUE GAMMA DATA TRANSFER
UGBW
W
Parameter
Reply
Control/Response contents
1-16 xxxx ··· xxxx
1-16 (xxxx: 32 pieces)
xxxx: 0000-1023
1-16
xxxx: User data of 32 pieces
RED GAMMA DATA READ
UGRR
W
GREEN GAMMA DATA READ
UGGR
W
BLUE GAMMA DATA READ
UGBR
W
USER DATA INITIALIZE
UGRS
W
0
Initialize the user data.
USER DATA SAVE
UGSV
W
0
Save the user data in the monitor.
44
*
aa: Block number
xxxx: 32 pieces of user data
cc: Checksum (ASCII data) of the block number and user data
aaxxxx ··· xxxxcc
(xxxx: 32 pieces)
aa: 01-16
xxxx: 0000-1023
cc: 00-FF
○
Controlling the Monitor with a PC (LAN)
Your monitor can be connected to a LAN allowing you to
control it from a PC on the LAN.
You can also configure the monitor to send e-mail notification
when it has a problem.
The connection requires a commercially available LAN cable
(UTP cable, Category 5, straight through).
Network (LAN)
Settings to connect to a LAN
Set the monitor’s IP address and subnet mask to match the
settings of your LAN.
These settings can be made on either the monitor or a PC
connected to the monitor.
The settings depend on the configuration of your LAN. Ask
your LAN administrator for details.
■ To set on the monitor
Hub
LAN terminal
LAN cable (commercially available, straight)
TIPS
• You must assign an IP address to the monitor by following
the procedures in “Settings to connect to a LAN”. (See the
description on the right.)
• Your PC must be installed with Internet Explorer (version 7.0
or later).
• To control the monitor via LAN, set RS-232C/LAN SELECT
to LAN. (See page 25.)
• You cannot use RS-232C and LAN control simultaneously.
Initializing personal information
• Personal information such as e-mail addresses can be
registered in the monitor. Before transferring or disposing of
the monitor, initialize all settings by selecting ALL RESET
1. (See page 32.) Note that ALL RESET 2 will not initialize
e-mail addresses and other settings.
Set RS-232C/LAN SELECT of COMMUNICATION SETTING
on the SETUP menu to LAN, and then set the LAN SETUP
options. (See page 25.)
ENTER
After setting each item, select SET and press
.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to ON.
To set the address manually, set this to OFF.
IP ADDRESS
If the DHCP CLIENT is set to OFF, specify an IP address.
Press
or
to select items, and press
or
to
change the values.
SUBNET MASK
If the DHCP CLIENT is set to OFF, specify the subnet mask.
Press
or
to select items, and press
or
to
change the values.
DEFAULT GATEWAY
If the DHCP CLIENT is set to OFF, specify the default
gateway.
If you are not using a gateway, specify “0.0.0.0”.
Press
or
to select items, and press
or
to
change the values.
RESET
Resets the values of the LAN settings to the factory preset
values.
ENTER
Select ON and then press
.
TIPS
• When the IP address is set manually, the IP addresses of
the monitor connected to the RS-232C output terminal and
the daisy chain of connected monitors that follows can be
assigned automatically. (See page 25.)
45
E
Controlling the Monitor with a PC (LAN)
■ To set from a PC
When the monitor is connected to a PC, LAN settings can be
configured via PC.
Set up process
(1) Connect your monitor to a PC
(2) Specify the PC’s IP address
(3) Configure the monitor’s LAN settings
7. Temporarily change the IP address and subnet mask.
To access the monitor as it is shipped from the factory, set
as follows.
• IP Address: 192.168.150.1
• Subnet Mask: 255.255.255.0
• Default Gateway: (leave blank)
(1) Connecting your monitor to a PC
Connect a commercially available crossover LAN cable
(UPT cable, Category 5) to the LAN port on the PC and this
monitor.
8. Click [OK] and then reboot the PC.
TIPS
PC
LAN terminal
To LAN terminal
LAN cable
(commercially available, crossover)
(2) Specifying the PC’s IP address
To configure the monitor’s LAN settings, you must temporarily
change the settings on the PC.
This explanation is based on Windows 7.
1. Log on to the PC with an administrator account.
2. Click [Start], and then click “Control Panel”.
3. Click “View network status and tasks” in “Network and
Internet”.
In “Classic View”, click “Network and Sharing Center”.
4. Click “Local Area Connection” and then “Properties”.
5. Click “Internet Protocol Version 4 (TCP/IPv4)” and then
“Properties”.
6. Make a note of the current IP address, subnet mask, and
default gateway settings.
Make sure you write this information now as you will
be changing the IP address, subnet mask, and default
gateway settings back to these settings afterwards.
E
46
• This monitor is factory preset as shown below.
(When DHCP CLIENT is set to OFF)
IP Address
: 192.168.150.2
Subnet Mask
: 255.255.255.0
Default Gateway : 0.0.0.0
(3) Configuring the monitor’s LAN settings
Access the monitor using Internet Explorer.
Controlling the monitor
1. Turn the power ON to the monitor.
2. Set RS-232C/LAN SELECT of COMMUNICATION
SETTING on the SETUP menu to LAN.
3. Set DHCP CLIENT of LAN SETUP of COMMUNICATION
SETTING on the SETUP menu to OFF.
PC operation
4. Launch Internet Explorer, in the “Address” box type
“http://192.168.150.2/” and press the Enter key.
Controlling the Monitor with a PC (LAN)
5. Click on “LAN SETUP” under NETWORK.
Controlling with a PC
■ Basic operation
You use Internet Explorer on a PC on the LAN to control the
monitor.
1. Launch Internet Explorer on the PC.
2. In the “Address” box, type “http://” followed by your monitor’s
IP address followed by “/”, then press the Enter key.
You can confirm the IP address with the DISPLAY function.
6. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to “ON”.
To set the address manually, set this to “OFF”.
IP ADDRESS
If the DHCP CLIENT is set to “OFF”, specify an IP address.
SUBNET MASK
If the DHCP CLIENT is set to “OFF”, specify the subnet mask.
DEFAULT GATEWAY
If the DHCP CLIENT is set to “OFF”, specify the default gateway.
If you are not using a default gateway, specify “0.0.0.0”.
7. When the setting is changed, click [Apply].
8. Check the message and click [OK].
9. Exit Internet Explorer.
10.Restore the PC’s IP address jotted in Step 6, “(2)
Specifying the PC’s IP address”.
11.Connect the monitor and the PC to the LAN.
When prompted to enter a user name and password, type
the user name and password that you specified in the
security settings (see page 49), and click [OK].
3. You can check, control, and change the monitor’s status
and settings by clicking the menu items on the left side of
the screen.
• If you see an [Apply] button next to a setting, click it after
you change that setting.
TIPS
• See pages 48 to 52 for details on each setting.
• If you click [Refresh] before the screen finishes updating
the current display, the “Server Busy Error” will appear.
Wait for a moment before operating your monitor again.
• You cannot operate the monitor while it is warming up.
DISPLAY
• If “DHCP CLIENT” is set to “ON”, press
on the
remote control unit two times and then check the monitor’s
IP address.
Caution
• Wait 10 seconds after clicking [OK] before proceeding.
• When operating using the remote control unit or similar,
click [Refresh].
TIPS
• When the IP address is set manually, the IP addresses of
the monitor connected to the RS-232C output terminal and
the daisy chain of connected monitors that follows can be
assigned automatically. (See page 25.)
47
E
Controlling the Monitor with a PC (LAN)
■ INFORMATION
Information about this monitor appears.
■ ADJUSTMENT
You can adjust these settings which are also available on the
monitor’s menu.
• SCREEN (See page 21.)
• PICTURE (See page 22.)
• PICTURE (ADVANCED) (See page 23.)
• AUDIO (See page 24.)
• SETUP (See page 24.)
• MONITOR (See page 26.)
• OTHERS (See page 28.)
• SCHEDULE (See page 30.)
• MULTI (See page 27.)
• PIP/PbyP (See page 27.)
• FUNCTION (See page 32.)
■ CONTROL
You can control the operations corresponding to the buttons
POWER INPUT SIZE
(
) on the remote control unit. (See page 18.)
TIPS
• After changing DISPLAY COLOR PATTERN to OFF, click
[Refresh] to correctly retrieve the status of the monitor.
TIPS
• In standby mode, Power ON is the operation available.
E
48
Controlling the Monitor with a PC (LAN)
■ NETWORK (LAN SETUP)
This screen allows you to set the settings necessary when the
monitor is connected to a LAN.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to ON.
To set the address manually, set this to OFF.
IP ADDRESS
If the DHCP CLIENT is set to OFF, specify an IP address.
SUBNET MASK
If the DHCP CLIENT is set to OFF, specify the subnet mask.
DEFAULT GATEWAY
If the DHCP CLIENT is set to OFF, specify the default
gateway.
If you are not using a default gateway, specify “0.0.0.0”.
DNS SERVER ADDRESS AUTO ACQUISITION
If the DHCP CLIENT is set to ON, specify whether or not to
automatically obtain the DNS server address.
DNS SERVER
Specify the DNS server address if the DHCP CLIENT
is SET to OFF or the DNS SERVER ADDRESS AUTO
ACQUISITION is set to OFF.
If you are not using a DNS server, specify “0.0.0.0”.
RESET
■ NETWORK (SECURITY)
This screen allows you to specify the security-related settings.
USER NAME / PASSWORD
Sets up a user name and password to restrict access to this
monitor.
After entering a user name and password, click [Apply].
ACCEPT IP ADDRESS
You can limit access to this monitor by registering IP
addresses of PCs that should have access.
To limit access, specify the option “From only specific IP
addresses”. Otherwise, to allow access from any PC, specify
“All IP Addresses”.
IP ADDRESS 1 to 3
If “ACCEPT IP ADDRESS” is set to “From only specific IP
addresses”, enter the IP addresses that you want to allow.
TIPS
• The USER NAME and PASSWORD can be up to 8
alphanumeric characters (hyphens and underscores
allowed).
• To cancel the user name and/or password after it has been
set, make the box empty and click [Apply].
Clicking [Execute] returns all of the LAN SETUP settings
to the factory-preset values except for the DNS SERVER
ADDRESS AUTO ACQUISITION and DNS SERVER
settings.
TIPS
• When the IP address is set manually, the IP addresses of
the monitor connected to the RS-232C output terminal and
the daisy chain of connected monitors that follows can be
assigned automatically. (See page 25.)
49
E
Controlling the Monitor with a PC (LAN)
■ NETWORK (GENERAL)
This screen allows you to specify the general LAN settings.
MONITOR NAME
Specify a name for this monitor as it should appear on the
Internet Explorer screen.
AUTO LOGOUT TIME
Specify the time (in minutes) to elapse before automatically
disconnecting this monitor from the network.
Specify in minutes from 1 to 65535. A value of ‘0’ will disable
this function.
DATA PORT
Specify the TCP port number to use for exchanging data with
the monitor.
Specify a value from 1025 to 65535.
SEARCH PORT
Specify the port number to use when searching for this
monitor.
Specify a value from 1025 to 65535.
INSTALLATION INFORMATION (NAME/LOCATION)
Specify the information to display for this monitor in the
Internet Explorer window.
LINK MODE
Selects the link speed and duplex.
Use AUTO normally.
TIPS
• The MONITOR NAME can be up to 16 alphanumeric
characters or symbols.
• Enter up to 50 characters in the NAME field in the
INSTALLATION INFORMATION.
• Enter up to 100 characters in the LOCATION field in the
INSTALLATION INFORMATION.
E
50
■ MAIL (ORIGINATOR)
This screen allows you to configure the e-mail sent periodically
or when the monitor has an error.
The settings depend on the configuration of your LAN. Ask
your LAN administrator for details.
SMTP SERVER
Specify the SMTP server address for sending e-mail.
* When using a domain name, make sure to specify the
DNS server as well. (See page 49.)
SMTP PORT
If the “AUTHENTICATION” is “SMTP-AUTH”, specify the port
number.
ORIGINATOR E-MAIL ADDRESS
Specify the e-mail address for this monitor.
This address becomes the e-mail address of the originator.
ORIGINATOR NAME
Specify the name for the originator.
This name appears in the “Originator Name” field of the
e-mail.
AUTHENTICATION
Specify the authentication method to use when sending
e-mail.
POP SERVER
If the “AUTHENTICATION” is “POP before SMTP”, specify
the POP server address.
ACCOUNT NAME / PASSWORD
If the “AUTHENTICATION” is “POP before SMTP” or
“SMTP-AUTH”, specify the account name and password to
connect to the SMTP server.
TIPS
• You can enter up to 64 alphanumeric characters or symbols
for the ORIGINATOR E-MAIL ADDRESS, ORIGINATOR
NAME, ACCOUNT NAME, and PASSWORD.
• The SMTP SERVER and POP SERVER can be up to 64
characters.
The following characters can be used: a-z, A-Z, 0-9, - , .
Controlling the Monitor with a PC (LAN)
■ MAIL (RECIPIENT)
This screen allows you to specify the recipients of the e-mail
sent periodically or when the monitor has an error.
RECIPIENT E-MAIL ADDRESSES
Specify the e-mail addresses to send error notification e-mail
to.
CONDITION
Specify the conditions to send mails.
When you check PERIODICAL, specify the date and time to
send the mails in the PERIODICAL setting.
CONFIRMATION
Sends test e-mail.
This allows you to confirm that the e-mail settings are
configured properly.
Attach the log file to a TEMPERATURE/HARDWARE error
e-mail.
When this option is checked, a log is added to the mail which
notifies a temperature or status error.
■ MAIL (PERIODICAL)
When PERIODICAL for CONDITION of MAIL (RECIPIENT) is
checked, set the date and time to send the mail.
DAY OF THE WEEK
Specify the day of the week to send the periodical mails.
TIME
Specify the time of the day to send the periodical mails.
Caution
• Do not turn off the main power when you set to send the
periodical mails.
• Specify the correct date and time. (See page 24.)
If the date and time settings are incorrect, the periodical
mail is not sent properly.
• Regularly confirm that the specified date and time is
correct.
• When LOW POWER is selected for STANDBY MODE,
periodical mails will not be sent in standby mode.
TIPS
• The RECIPIENT E-MAIL ADDRESSES can be up to 64
alphanumeric characters or symbols.
51
E
Controlling the Monitor with a PC (LAN)
■ SNMP
You can configure settings related to SNMP.
Caution
• After you set SNMP, click [Switch the main power of
monitor off and on now.] or turn off the monitor and then
turn it on again with the main power switch. When the
monitor restarts, wait about 30 seconds and then start the
next operation.
• If the IP address is changed while the SNMP function is
operational, turn off the monitor and then turn it on again
with the main power switch.
TIPS
• Depending on the SNMP settings, a short delay may occur
before the SNMP is usable. (About 5 minutes)
• Up to 16 alphanumeric letters and symbols can be used for
the community name, user name and password.
■ SERVICE & SUPPORT
(URL INFORMATION)
You can display a specific URL in the URL INFORMATION
field on the INFORMATION screen when an error occurs in
the monitor. (See page 48.)
SNMP SETTING
Set whether to enable or disable SNMP.
VERSION
Set the version of the SNMP to be supported.
COMMUNITY NAME 1 to 3
Set the name of the community required for the access.
USER 1 to 3
Set the user name, password, authentication method and
other options required for access.
TRAP SETTING
Set whether to enable or disable the trap function.
When this function is enabled, a trap will be sent when the
monitor is turned on.
TRAP SETTING OF AUTHENTICATION ERROR
Set whether the trap function sends a notification when
authentication fails.
TRAP ADDRESS & PORT
Set the destination address and port number of the
notification sent by the trap function.
E
52
URL INFORMATION
Enter the URL to display on the INFORMATION screen when
an error occurs on the monitor.
Up to 64 alphanumeric characters or symbols can be used.
CONDITION
Specify the condition to display the URL.
CONFIRMATION
The home page of the specified URL is displayed.
You can check whether the URL you entered is correct.
TIPS
• It is also possible to specify the message text, such as the
name of a contact or a telephone number, to be displayed
instead of the linked URL.
Controlling the Monitor with a PC (LAN)
[Advanced operation]
Command-based control
You can control the monitor using RS-232C commands
(see page 36) via terminal software and other appropriate
applications.
In order to use this function, enable a connection to the
monitor through Internet Explorer.
Read the manual for the terminal software for detailed
instructions.
(1) Connect the PC to the monitor.
1. Specify the IP address and data port number and
connect the PC to the monitor.
When connection has been established successfully,
[ Login:] is returned as response.
2. Send the user name set in the SECURITY settings (see
page 49).
• Send [User name] + [ ].
• If the user name is not set, send [ ].
• When the transmission is successful, [ Password:]
is returned as response.
3. Send the password set in the SECURITY settings (see
page 49).
• Send [Password] + [ ].
• If the password is not set, send [ ].
• When the transmission is successful, [OK
] is
returned as response.
(2) Send commands to control the monitor.
• The commands used are the same as those for RS232C. Refer to the communication procedure (see
page 33) for operation.
• Usable commands are provided in the RS-232C
command table (see page 37).
(3) Disconnect the connection with the monitor and
quit the function.
1. Send [BYE ].
When the transmission is successful, [goodbye] is
returned and the connection is disconnected.
TIPS
• Connection is automatically disconnected when the
time specified in AUTO LOGOUT TIME elapses over a
no‑communication period.
53
E
Troubleshooting
If you are experiencing any problem with your display, before
calling for service, please review the following troubleshooting
tips.
There is no picture or sound.
• Is the power cord disconnected? (See page 13.)
• Is the main power switch off? (See page 16.)
• Is the monitor in standby mode (the power LED illuminating
in orange)? (See page 16.)
• Make sure correct input mode is selected. (See page 18.)
• If any external equipment is connected, make sure the
equipment is operating (playing back).
Remote control does not work.
• Are the batteries inserted with polarity (+,-) aligned? (See
page 15.)
• Are the batteries exhausted?
• Point the remote control unit toward the monitor’s remote
control sensor. (See page 15.)
• Is the menu display hidden or is operation disabled? (See
page 32.)
Sound from left and right speakers is reversed.
Sound is heard from only one side.
• Are audio cables connected properly?
• Check the setting of BALANCE for AUDIO menu. (See
page 24.)
There is a picture but no sound.
• Is the sound muted?
• Make sure the volume is not set to minimum.
• Are audio cables connected properly?
• Is the setting of AUDIO SELECT on the SETUP menu
correct? (See page 24.)
Unstable video.
• The signal may be incompatible.
• Try the automatic screen adjustment when the
D-SUB[RGB] or DVI-I (analog) are used.
The video from the PC/AV HDMI input terminal does not
appear properly.
• Is the setting for HDMI1 or HDMI2 of INPUT SELECT on
the SETUP menu correct? (See page 24.)
• Is the HDMI cable HDMI standard compliant? The monitor
will not work with cables that are not standard compliant.
• Is the input signal compatible with this monitor? (See page
59.)
The video from the DVI-I input terminal does not appear
properly.
• Is the setting for EDID SELECT (DVI-I) of INPUT SELECT
on the SETUP menu correct? (See page 24.)
• Is the input signal compatible with this monitor? (See page
59.)
• Turn off the power to the connected equipment and then
turn the power on again.
• If the monitors are connected in a daisy chain, turn off the
power to all the monitors connected in a daisy chain and
then turn the power on again.
E
54
The video from PC/AV D-Sub input terminal does not
appear correctly.
• Is the setting for D-SUB of INPUT SELECT on the SETUP
menu correct? (See page 24.)
• Is the input signal compatible with this monitor? (See page
59.)
The video from the DisplayPort does not appear properly.
• Is the input signal compatible with this monitor? (See page
59.)
Control buttons do not work.
There is no picture.
• Load noises from outside may be interfering with normal
operation. Turn off the power and turn it on after waiting at
least 5 seconds, and then check the operation.
The input mode changes automatically.
• When the AUTO INPUT CHANGE is ON and no signal
is present in a selected input mode, the AUTO INPUT
CHANGE automatically changes the selected mode to a
mode where a video signal is present.
The input mode may change in the following cases:
-When a computer is in standby mode.
-When video play is stopped with a playback device.
Power LED flashes red.
“STATUS [xxxx]” appears in the corner of the screen.
• Hardware has a problem. Turn off the monitor and request
repair from your SHARP dealer.
(When STATUS ALERT is set to OSD & LED. This varies
depending on the setting.)
When “AUTO DIMMING” is displayed.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight automatically
decreases in order to prevent a further temperature rise. If
you attempt to use
to adjust the brightness while
the monitor is in this state, “AUTO DIMMING” is displayed
and you cannot change the brightness.
• Remove the cause of the excessive temperature rise.
The monitor makes a cracking sound.
• You may occasionally hear a cracking sound from the
monitor. This happens when the cabinet slightly expands
and contracts according to change in temperature. This
does not affect the monitor’s performance.
Troubleshooting
The Power LED is flashing in red and green alternately.
When “TEMPERATURE” is displayed in the corner of the
screen.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight decreases
automatically in order to prevent high-temperaturerelated problems. When this occurs, “TEMPERATURE” is
displayed on the screen and the Power LED flashes red
and green alternately. (When TEMPERATURE ALERT is
set to OSD & LED. This varies depending on the setting.)
• If the internal temperature rises further, the monitor
automatically enters standby mode. (The Power LED
continues flashing red and green alternately.)
• Remove the cause of the excessive temperature rise.
- If the monitor enters standby mode due to a rise in
temperature, to return to normal display, turn the power
switch off and then back on again. The monitor, however,
will enter standby mode again if the cause of the
temperature rise is not eliminated. (See page 7.)
- Check whether the monitor is placed at a location where
a quick rise in temperature is likely. Internal temperature
rises quickly if the vents on the monitor are blocked.
- Internal temperature rises quickly if dust accumulates
inside the monitor or around the vents. Remove dust if
possible. Ask SHARP dealer about removing internal dust.
55
E
Specifications
nProduct Specifications
Model
LCD component
PN-R703
PN-R603
70" Class [69-1/2 inch (176.6cm)
60" Class [60-1/16 inch (152.5cm)
diagonal] TFT LCD
diagonal] TFT LCD
Max. resolution
(pixels) 1920 x 1080
Max. colors
Approx. 1.06 billion colors
Pixel pitch
0.802 mm (H) × 0.802 mm (V)
0.692 mm (H) × 0.692 mm (V)
Viewing angle
176° right/left/up/down (contrast ratio ≥ 10)
Screen active area
inch (mm) 60-9/16 x 34-1/16 (1538.9 x 865.6) 52-5/16 x 29-7/16 (1329.1 x 747.6)
Computer input signal
Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 Ω],
DisplayPort 1.1
Sync signal
Horizontal/vertical separate (TTL: positive/negative), Sync-on-green*1,
Composite sync (TTL: positive/negative)*1
Video color system
NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM
Plug and play
VESA DDC2B
Power management
VESA DPMS, DVI DMPM
Input terminals
PC/AV
HDMI x 2
Mini D-sub 15 pin, 3 rows x 1
PC
DisplayPort x 1
DVI-I 29 pin (HDCP compatible) x 1
Audio
3.5 mm mini stereo jack x 2
Serial (RS-232C)
D-sub 9 pin x 1
Output terminals
PC
DisplayPort x 1
DVI-D 24 pin (HDCP compatible) x 1
Audio
3.5 mm mini stereo jack x 1
Serial (RS-232C)
D-sub 9 pin x 1
LAN terminal
10 BASE-T/100 BASE-TX
Speaker output
10 W + 10 W
Power requirement
AC 100 - 240 V, 3.0 - 1.2 A, 50/60 AC 100 - 240 V, 2.3 - 1.0 A,
Hz
50/60 Hz
2
32°F to 104°F (0°C to 40°C)
Operating temperature *
Operating humidity
20% to 80% (no condensation)
Power consumption
270 W (1.4 W / 1.4 W)
200 W (1.4 W / 1.4 W)
(Input signal waiting mode *3 / standby mode *4)
Dimensions (excluding protrusions)
inch (mm) Approx. 62-1/8 (W) x 1-9/16 (D) x Approx. 54-1/4 (W) x 1-9/16 (D) x
36-1/16 (H) (1578 x 39.4 x 916)
31-1/4 (H) (1378 x 39.4 x 794)
Weight lbs. (kg) Approx. 94.8 (43)
Approx. 70.5 (32)
*1
*2
*3
*4
D-Sub input terminal only.
Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such
cases, please check the temperature condition specified by the optional equipments.
When AUTO INPUT CHANGE is set to OFF.
When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
E
56
Specifications
nDimensional Drawings
Note that the values shown are approximate values.
[PN-R703]
VESA holes *
1-9/16
[39.4]
7-7/8
[200]
7-7/8
[200]
Unit: inch [mm]
3-15/16 3-15/16
[100] [100]
62-1/8 [1578]
7/16
[11.2]
7-7/8
[200]
36-1/16 [916]
Opening height (34-1/2 [877])
Opening width(60-11/16 [1541])
When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method.
SHARP recommends using M6 screws and tighten the screws.
Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in
serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch
(8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times
or more the weight of the monitor.
[PN-R603]
VESA holes *
7-7/8
[200]
1-9/16
[39.4]
7-7/8
[200]
Unit: inch [mm]
3-15/16 3-15/16
[100] [100]
54-1/4 [1378]
7/16
[11.2]
7-7/8 [200]
31-1/4 [794]
Opening height (29-3/4 [755])
Opening width (52-3/4 [1340])
When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method.
SHARP recommends using M6 screws and tighten the screws.
Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in
serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch
(8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times
or more the weight of the monitor.
57
E
Specifications
nPower management
This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in
order for the monitor’s power management function to work.
DMPM: Digital Monitor Power Management
DPMS: Display Power Management Signaling
DPMS
Screen
Power
consumption*1
Hsync
Vsync
DMPM
Screen
Power
consumption*1
ON STATE
Display
270 W
200 W
Yes
Yes
Monitor ON
Display
270 W
200 W
No
display
1.4 W*2
1.4 W*2
No
Yes
Yes
No
Active OFF
No display
1.4 W*2
1.4 W*2
No
No
STANDBY
SUSPEND
OFF STATE
*1Upper value: PN-R703, Lower value: PN-R603.
*2When AUTO INPUT CHANGE is set to OFF.
nDDC (plug and play)
The monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters
is exchanged between the two. This function can be used if the computer supports DDC and it has been configured to detect
plug-and-play monitors.
There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.
E
58
Specifications
nCompatible signal timing (PC)
Screen resolution
VESA
640 × 480
800 × 600
848 × 480
1024 × 768
1152 × 864
1280 × 768
1280 × 800
1280 × 960
1280 × 1024
Wide
US TEXT
Sun
1360 × 768
1400 × 1050
1440 × 900
1600 × 1200*
1680 × 1050
1920 × 1200*
1280 × 720
1920 × 1080
720 × 400
1024 × 768
1152 × 900
1280 × 1024
1600 × 1000
Hsync
Vsync
Dot frequency
31.5kHz
37.9kHz
37.5kHz
35.1kHz
37.9kHz
48.1kHz
46.9kHz
31.0kHz
48.4kHz
56.5kHz
60.0kHz
67.5kHz
47.8kHz
60.3kHz
49.7kHz
60.0kHz
64.0kHz
80.0kHz
47.7kHz
65.3kHz
55.9kHz
75.0kHz
65.3kHz
74.0kHz
44.7kHz
66.3kHz
67.5kHz
31.5kHz
48.3kHz
53.6kHz
56.6kHz
61.8kHz
71.8kHz
71.7kHz
81.1kHz
68.6kHz
60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
60Hz
70Hz
75Hz
75Hz
60Hz
75Hz
60Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
70Hz
60Hz
66Hz
70Hz
66Hz
76.2Hz
67.2Hz
76Hz
66Hz
25.175MHz
31.5MHz
31.5MHz
36.0MHz
40.0MHz
50.0MHz
49.5MHz
33.75MHz
65.0MHz
75.0MHz
78.75MHz
108.0MHz
79.5MHz
102.25MHz
83.5MHz
108.0MHz
108.0MHz
135.0MHz
85.5MHz
121.75MHz
106.5MHz
162.0MHz
146.25MHz
154.0MHz
74.4MHz
148.5MHz
148.5MHz
28.3MHz
64.13MHz
70.4MHz
74.25MHz
94.88MHz
108.23MHz
117.01MHz
134.99MHz
135.76MHz
Digital
DVI-I
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
HDMI
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
Analog
DisplayPort (D-SUB/DVI-I)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
* Displays a reduced image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed.
• All are compliant only with non-interlaced.
• Depending on the connected PC, images may not be displayed properly even if the compatible signal described above is input.
• The frequency values for the Sun are reference values.
nCompatible signal timing (AV)
Screen resolution
1920 × 1080p
1920 × 1080i
1280 × 720p
720 × 576p
720 × 480p
640 × 480p(VGA)
720(1440) × 576i
720(1440) × 480i
Frequency
24Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
HDMI
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Component
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
59
E
Specifications
nDVI-I input
(DVI-I 29 pin)
No.
1
Function
No.
Function
16
Hot-plug detection
1
TMDS data 2+
11
TMDS clock shield
No.
Function
No.
Function
2
TMDS data 2+
17
TMDS data 0-
2
TMDS data 2 shield
12
TMDS clock-
3
TMDS data 2/4 shield
18
TMDS data 0+
3
TMDS data 2-
13
CEC
4
N.C.
19
TMDS data 0/5 shield
4
TMDS data 1+
14
N.C.
5
N.C.
20
N.C.
5
TMDS data 1 shield
15
SCL
6
DDC clock
21
N.C.
6
TMDS data 1-
16
SDA
7
DDC data
22
TMDS clock shield
7
TMDS data 0+
17
DDC/CEC GND
8
Analog Vsync signal
23
TMDS clock+
8
TMDS data 0 shield
18
+5V
9
TMDS data 1-
24
TMDS clock-
9
TMDS data 0-
19
Hot-plug detection
10
TMDS data 1+
C1 Analog red video signal
10
TMDS clock+
11
TMDS data 1/3 shield
C2 Analog green video signal
12
N.C.
C3 Analog blue video signal
13
N.C.
C4 Analog Hsync signal
14
+5V
C5 Analog GND
15
GND
No.
terminal pins
Function
No.
Function
nRS-232C input
(D-sub 9 pin)
No.
terminal pins
Function
No.
Function
1
Red video signal input
9
+5V
1
N.C.
6
N.C.
2
Green video signal input
10
GND
2
Transmitted data
7
N.C.
3
Blue video signal input
11
N.C.
3
Received data
8
N.C.
4
N.C.
12
DDC data
4
N.C.
9
N.C.
Hsync signal input
5
GND
5
GND
13
6
GND for red video signal
14
7
GND for green video signal 15
8
GND for blue video signal
nDisplayPort input
(DisplayPort 20 pin)
No.
60
terminal pins
TMDS data 2-
nPC/AV D-sub input
(Mini D-sub 15 pin)
E
nPC/AV HDMI input
(HDMITM Connector)
terminal pins
Function
Vsync signal input
DDC clock
terminal pins
No.
Function
1
MainLane 3-
11
2
Gnd
12
MainLane 0+
3
MainLane 3+
13
Gnd
4
MainLane 2-
14
Gnd
5
Gnd
15
Aux +
6
MainLane 2+
16
Gnd
7
MainLane 1-
17
Aux -
8
Gnd
18
Hot-plug detection
9
MainLane 1+
19
Gnd
10
MainLane 0-
20
3.3V
Gnd
Specifications
nDVI-D output
(DVI-D 24 pin)
No.
1
nRS-232C output
(D-sub 9 pin)
terminal pins
Function
No.
Function
No.
Function
terminal pins
No.
Function
TMDS data 2-
13
N.C.
1
N.C.
6
N.C.
2
TMDS data 2+
14
+5V
2
Received data
7
N.C.
3
TMDS data 2/4 shield
15
GND
3
Transmitted data
8
N.C.
4
N.C.
16
Hot-plug detection
4
N.C.
9
N.C.
5
N.C.
17
TMDS data 0-
5
GND
6
DDC clock
18
TMDS data 0+
7
DDC data
19
TMDS data 0/5 shield
8
N.C.
20
N.C.
9
TMDS data 1-
21
N.C.
10
TMDS data 1+
22
TMDS clock shield
11
TMDS data 1/3 shield
23
TMDS clock+
12
N.C.
24
TMDS clock-
nDisplayPort output
(DisplayPort 20 pin)
No.
Function
terminal pins
No.
Function
1
MainLane 0+
11
Gnd
2
Gnd
12
MainLane 3-
3
MainLane 0-
13
Gnd
4
MainLane 1+
14
Gnd
5
Gnd
15
Aux +
6
MainLane 1-
16
Gnd
7
MainLane 2+
17
Aux -
8
Gnd
18
Hot-plug detection
9
MainLane 2-
19
Gnd
10
MainLane 3+
20
3.3V
61
E
Mounting Precautions
(For SHARP dealers and service engineers)
• When installing, removing or moving the monitor, ensure that this is carried out by at least 3 people.
(PN-R603: at least 2 people.)
• Be sure to use a wall-mount bracket designed or designated for mounting the monitor.
• This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials
such as plaster / thin plastic board / wood before starting installation.
• This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor.
Install by the most suitable method for the material and the structure.
• To attach a VESA-compliant mounting bracket, use M6 screws that are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the
thickness of the mounting bracket.
• Do not use an impact driver.
• When moving the monitor, be sure to hold the areas shown in the figure below. Do not hold the LCD panel. This may cause
product damage, failure, or injury.
• After mounting, please carefully ensure the monitor is secure, and not able to come loose from the wall or mount.
• Do not use any screw holes other than VESA holes for installation.
E
62
PN-R703R603 Mu EN12M(1)