Chief LPAUS Installation Instructions
Add to my manuals
12 Pages
Chief LPAUS is a height adjustable video cart designed for use with displays weighing up to 200 lbs (90.7 kg). It features a +/-2° roll adjustment and +/-5° tilt adjustment for precise positioning of the display. The cart also has cable management covers to keep cords and cables organized and out of sight. With its sturdy construction and easy-to-use design, the Chief LPAUS is a versatile and reliable solution for mounting and displaying large displays in various settings.
advertisement
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Height Adjustable Video Cart
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
LPAU
LPAU
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
Installation Instructions
WARNING: Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is damaged. Return the mounting system to a service center for examination and repair.
WARNING: Do not use this product outdoors.
WARNING: RISK OF INJURY TO PERSONS! Do not place video equipment such as televisions or computer monitors on cart legs.
--SAVE THESE INSTRUCTIONS--
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.
WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.
WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the component.
WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components located between the LPAU up to (and including) the display does not exceed 200 lbs (90.7 kg).
2
Installation Instructions
DIMENSIONS
+/-2 ROLL
ADJUSTMENT
CABLE CORD WRAP HOOKS
+/-5 TILT
ADJUSTMENT
15.75
400.0
CABLE
MANAGEMENT
COVERS
CABLE
MANAGEMENT
COVERS
7.87 [200] MIN
31.50 [800] MAX
70.05
1779.3
MAX HEIGHT TO
CENTER OF DISPLAY
50.05
1271.3
MIN HEIGHT TO
CENTER OF DISPLAY
45.00
1143.0
CABLE
MANAGEMENT
COVERS
33.23
844.0
LPAU
3
LPAU
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
4
Installation Instructions
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
LPAU
#2
M5 (included)
3/16" (included)
PARTS
T (1)
[hardware bag]
C (1)
[column upper
A (4)
[upright cover]
B (2)
[interface upright] cover]
D (1)
[column inner cover]
E (1)
[interface head assembly]
TA (8)
M4x16mm
TB (6)
M4x20mm
TC (6)
M4x25mm
G (1)
[back cover]
TD (6)
M5x16mm
TE (6)
M5x20mm
TF (6)
M5x25mm
F (1)
[column assembly] TG (6)
M6x16mm
TH (6)
M6x25mm
J (1)
[right cart leg]
K (2)
[cable hook]
TI (6)
M8x20mm
TJ (6)
M8x30mm
TK (4)
M8x50mm
H (1)
[left cart leg]
N (5)
5/16-18 x 3/4"
L (1)
[left transition cover]
M (1)
[right transition cover]
TL (8)
1/4"
TM (8)
1/2"
TN (8)
[universal]
TP (1)
M5
P (4)
5/16-18 x 3 3/4"
Q (2)
1/4-20 x 1/2"
R (1)
3/16"
U (10)
[FCA clip]
V (10)
[cable tie]
W (1)
3/16"
5
LPAU
Assembly And Installation
CAUTION: Attachment holes may be damaged if a power drill is used to insert button head cap screws. Screws should first be inserted and turned BY HAND with the hex key or with a handheld screwdriver BEFORE using the head head drill bit and power drill to complete the attachment.
Cart Assembly
1.
Carefully set column assembly (F) on its left side. (See
Figure 1)
2.
Place right transition cover (M) on right cart leg (J), lining up the holes on the cover with the holes on the leg and column assembly base. (See Figure 1)
3.
Use two 5/16-18 x 3 3/4" button head cap screws (P) to secure leg (J) and cover (M) to column assembly (F). (See
Figure 1)
(rear view)
3 (P) x 2
Installation Instructions
5.
Place left transition cover (L) on left cart leg (H), lining up the holes on the cover with the holes on the leg and column assembly base. (See Figure 2)
6.
Use two 5/16-18 x 3 3/4" button head cap screws (P) to secure leg (H) and cover (L) to column assembly (F). (See
Figure 2)
7.
Slide interface head assembly (E) into column assembly
(F). (See Figure 3)
8.
Use four 5/16-18 x 3/4" button head cap screws (N) to secure interface head assembly (E) to column assembly
(F). (See Figure 3)
8 (N) x 4
(E)
7
(F)
(J)
2
(M)
(F)
1
Figure 1
4.
Turn column assembly (F) onto its right side. (See Figure 2)
6
(P) x 4
Figure 3
9.
Use remaining 5/16-18 x 3/4" button head cap screw (N) to secure column upper cover (C) to interface head assembly
(E). (See Figure 4)
10. Snap column inner cover (D) onto column assembly (F).
(See Figure 4)
9 (N)
(C)
(E)
(H)
5
(L)
(D)
4
10
(F)
10
(F)
Figure 2
Figure 4
6
Installation Instructions
Display Installation
LPAU
WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components located between the LPAU up to (and including) the display does not exceed 200 lbs (90.7 kg).
1.
Lay display face down on protective surface.
CAUTION: Using screws of improper diameter may damage your display! Proper screws will easily thread into display mounting holes.
2.
Select screw diameter by examining hardware (TA-TK)
(4mm, 5mm, 6mm or 8mm) and comparing with mounting holes on display. (See Figure 5)
3.
Select spacers: (See Figure 5)
• If mounting holes are not recessed and both uprights (B) can lay flat against display, then no spacers are required.
• If mounting holes are recessed, or if protrusions prevent uprights (B) from laying flat, then spacers
(TL or TM) must be used.
CAUTION: Using screws of improper length may damage your display! Proper screws will have adequate thread engagement without contacting bottom of display mounting holes.
4.
Select screw length: (See Figure 5)
• Using your hand, insert SHORTEST length screw of selected diameter (TA, TD, TG or TI) through universal washer (TN), uprights (B), selected spacer (TL or TM), into display mounting hole. Do
NOT thread screw into hole at this time.
NOTE: Universal washers (TN) are not needed if using M8 button head cap screws (TI, TJ or TK).
• Proper screw length requires base of screw head to protrude above flat washer a distance equal to
or greater than the screw diameter. If screw length is inadequate, select longer screw. Select
shortest screw which will protrude the required distance.
5.
Place uprights (B) on display, ensuring: (See Figure 5)
• Center of uprights (B) are as close to the center of the back of display as possible after being installed. Center of bracket is indicated by the diamond-shaped hole.
6.
Use selected screws and spacers to install two interface uprights (B) to back of display. (See Figure 5)
6 (TA-TH) or (TI-TK) x 4, 6 or 8
(B) x 2
5
5
3 (TL or TM)
Figure 5
7
LPAU
WARNING: Display may be very heavy! Ensure display may be safely lifted and maneuvered as required to install on cart. Failure to take adequate precautions can result in serious personal injury or damage to equipment!
7.
Position latches on interface uprights so that they are in the
"open" position. (See Figure 6)
8.
Hang interface uprights (B) on interface head assembly (E).
(See Figure 6)
Installation Instructions
9.
Move latches on interface uprights to the "closed" position to secure display to head assembly. (See Figure 8)
9 open position
9
Figure 8
10. Snap four upright covers (A) onto uprights. (See Figure 9)
NOTE: Tabs on inside of covers (A) will snap directly into holes on uprights to ensure a secure connection.
8
7
7
8 10 (A) x 4
(B) x 2
Figure 6
IMPORTANT ! : In order to ensure an even mount, install uprights to be centered over column assembly. Do NOT install both uprights to the same side of column assembly! (See Figure 7)
11
Figure 9
11. (Optional) Use padlocks (not provided) to secure uprights to head assembly. (See Figure 9)
Figure 7
8
Installation Instructions
Cable Management
NOTE: The following cable management options may vary based on type of display being mounted and user preference.
1.
Use two 1/4-20 x 1/2" Phillips pan machine screws (Q) to attach two cable hooks (K) to bottom of column assembly
(F). (See Figure 10)
LPAU
5.
Route cables along FCA clips to be used for cable management. (See Figure 12)
6.
Use cable ties (V) to secure cables to FCA clips. (See
Figure 12)
(F)
5
6 (V)
(K) x 2 1 (Q) x 2
Figure 10
2.
Place FCA clip (U) into groove on back of Fusion mount with clip handle in a vertical position. (See Figure 11)
3.
Rotate FCA clip (U) 90° in either direction until clip handle is in a horizontal position. (See Figure 11)
4.
Repeat Steps 1-2 for all clips to be installed.
Figure 12
7.
Route cables from display through front channel of column assembly. (See Figure 13) cable (example)
7
3
3
2
(U) front channel clip handle
Figure 13
Figure 11
9
LPAU
8.
Route cables down column channel, tucking them behind height-adjustment carriage and underneath bracket holding height-adjustment shaft. (See Figure 14)
9.
Wrap cables around cable hooks as desired. (See Figure
14)
10. Snap back cover (G) onto back of column assembly making sure cables fit through opening at bottom of cover. (See
Figure 14)
Installation Instructions
Adjustments
Height Adjustment
1.
Remove cable cover (G) to expose height adjustment knob.
2.
Turn height adjustment knob clockwise to raise display.
(See Figure 15)
3.
Turn height adjustment knob counterclockwise to lower display. (See Figure 15)
(rear view)
10
(G)
WARNING: Do not attempt to raise or lower the adjustment carriage beyond its upper or lower limit. High and low points are shown in Figures 15 and 16.
NOTE: A 1/2" socket wrench may also be used to adjust height by turning bolt just above height adjustment knob.
4.
Reinstall cable cover (G) to column assembly.
8
10 height adjustment knob
8 under bracket
2 3
1 high point
2
1 9 cable hooks
Figure 14 cable opening
3
Figure 15 low point
Figure 16
10
Installation Instructions
Pitch Adjustment
5.
Turn pitch adjustment knob clockwise to tilt display forward.
(See Figure 17)
6.
Turn pitch adjustment knob counterclockwise to tilt display back. (See Figure 17)
Roll Adjustment
7.
Turn roll adjustment knob clockwise to adjust roll to the left.
(See Figure 17)
8.
Turn roll adjustment knob counterclockwise to adjust roll to the right. (See Figure 17)
7
8
5
5 6
7 8
6 pitch adjustment knob roll adjustment knob
Figure 17
LPAU
11
LPAU Installation Instructions
Chief Manufacturing, a products division of Milestone AV Technologies
8800-002209 Rev03
2013 Milestone AV Technologies, a
Duchossois Group Company www.chiefmfg.com
01/13
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
Europe
F 877.894.6918 / 952.894.6918
A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
Asia Pacific
F +31 (0) 495 580 845
A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Multimedia cart Flat panel Silver
- Maximum weight capacity: 90.7 kg Maximum screen size: 2.03 m (80")
- VESA mounting
- 4 wheel(s)