Contents
AV RECEIVER
TX-NR525
Safety Information and Introduction ............2
Table of Contents ...........................................5
Connections .................................................11
Turning On & Basic Operations..................20
Instruction Manual
Playback........................................................24
Advanced Operations ..................................41
Controlling Other Components...................57
Appendix .......................................................63
Internet Radio Guide
Remote Control Codes
En
Safety Information and Introduction
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN
OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING
AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by
the manufacturer.
12. Use only with the cart,
PORTABLE CART WARNING
stand, tripod, bracket, or
table specified by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
S3125A
combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
A. When the power-supply cord or plug is
damaged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
En-2
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by the
operating instructions as an improper
adjustment of other controls may result in
damage and will often require extensive work
by a qualified technician to restore the
apparatus to its normal operation,
E. If the apparatus has been dropped or
damaged in any way, and
F. When the apparatus exhibits a distinct change
in performance this indicates a need for
service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus
through openings as they may touch dangerous
voltage points or short-out parts that could result
in a fire or electric shock.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such
as vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top
of this unit.
17. Batteries
Always consider the environmental issues and
follow local regulations when disposing of
batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is
adequate ventilation.
Leave 20 cm (8") of free space at the top and
sides and 10 cm (4") at the rear. The rear edge of
the shelf or board above the apparatus shall be
set 10 cm (4") away from the rear panel or wall,
creating a flue-like gap for warm air to escape.
Safety Information and Introduction
Precautions
1. Recording Copyright—Unless it’s for personal
use only, recording copyrighted material is illegal
without the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
3. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a
soft cloth dampened with a weak solution of mild
detergent and water. Dry the unit immediately
afterwards with a clean cloth. Don’t use abrasive
cloths, thinners, alcohol, or other chemical
solvents, because they may damage the finish or
remove the panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION
CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear
panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this
unit from the AC power source. Make sure that
the plug is readily operable (easily accessible) at
all times.
5.
6.
7.
8.
extended period, remove the power cord from the
AC outlet.
Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and
headphones can cause hearing loss.
Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall
not be exposed to excessive heat as sunshine,
fire or the like.
Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you
originally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks
on the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
For models with [POWER] button, or with both
[POWER] and [ON/STANDBY] buttons:
Pressing the [POWER] button to select OFF
mode does not fully disconnect from the mains. If
you do not intend to use the unit for an extended
period, remove the power cord from the AC outlet.
For models with [ON/STANDBY] button only:
Pressing the [ON/STANDBY] button to select
Standby mode does not fully disconnect from the
mains. If you do not intend to use the unit for an
En-3
For U.S. models
FCC Information for User
CAUTION:
The user changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Safety Information and Introduction
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized
plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
Modèle pour les Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME
NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
For British models
Replacement and mounting of an AC plug on the
power supply cord of this unit should be performed
only by qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in
accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected
to the terminal which is marked with the letter L or
coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must
approved by ASTA or BSI to BS1362 and have the
same ampere rating as that indicated on the plug.
Check for the ASTA mark or the BSI mark on the
body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable
fuse in the plug.
Thank you for purchasing an Onkyo AV
Receiver. Please read this manual thoroughly
before making connections and plugging in the
unit.
Following the instructions in this manual will
enable you to obtain optimum performance and
listening enjoyment from your new AV Receiver.
Please retain this manual for future reference.
Supplied Accessories
Make sure you have the following accessories:
Indoor FM antenna (➔ page 18)
For European Models
Declaration of Conformity
We declare, under our sole
responsibility, that this product
complies with the standards:
–Safety
–Limits and methods of
measurement of radio disturbance characteristics
–Limits for harmonic current emissions
–Limitation of voltage changes, voltage fluctuations
and flicker
–RoHS Directive, 2011/65/EU
En-4
AM loop antenna (➔ page 18)
Power cord (Taiwanese models) (➔ page 20)
Speaker cable labels (➔ page 11)
Speaker setup microphone (➔ page 22)
Remote controller (RC-865M) and two batteries (AA/R6)
Quick Start Guide
*
In catalogs and on packaging, the letter at the end of the
product name indicates the color. Specifications and
operations are the same regardless of color.
Safety Information and Introduction
Table of Contents
Safety Information and Introduction
Important Safety Instructions ......................................2
Precautions ...................................................................3
Supplied Accessories...................................................4
Table of Contents..........................................................5
Features .........................................................................6
Front & Rear Panels......................................................7
Front Panel..................................................................7
Display ........................................................................8
Rear Panel ..................................................................9
Remote Controller.......................................................10
Controlling the AV Receiver ......................................10
Connections
Connecting the AV Receiver......................................11
Connecting Your Speakers .......................................11
Connecting the TV/AV components ..........................14
About RIHD-compatible components........................15
Operations that can be performed
with RIHD connection .............................................16
Confirm the settings ..................................................16
Connection Tips ........................................................17
Connecting the Antennas..........................................18
Connecting Onkyo RI Components...........................19
Using Headphones....................................................19
Turning On & Basic Operations
Turning On/Off the AV Receiver ................................20
Connecting the Power Cord ......................................20
Turning On ................................................................20
Turning Off ................................................................20
Firmware Update Notification....................................20
About the HYBRID STANDBY indicator....................20
Using the Automatic Speaker Setup .........................21
Playback
Controlling Other Components
Playback ...................................................................... 24
Controlling Contents of USB or Network Devices..... 25
Understanding Icons on the Display ......................... 26
Playing an iPod/iPhone via USB............................... 26
Playing a USB Device............................................... 27
Listening to TuneIn ................................................... 27
Registering Other Internet Radio .............................. 28
Playing Music Files on a Server (DLNA) .................. 29
Playing Music Files on a Shared Folder ................... 30
Remote Playback...................................................... 31
Listening to AM/FM Radio ........................................ 32
Playing Audio and Video from Separate Sources..... 34
Using the Listening Modes ....................................... 35
Displaying Source Information.................................. 39
Using the Sleep Timer .............................................. 39
Setting the Display Brightness.................................. 39
Changing the Input Display....................................... 39
Muting the AV Receiver ............................................ 39
Using the Home Menu .............................................. 40
Controlling Other Components................................. 57
Preprogrammed Remote Control Codes .................. 57
Entering Remote Control Codes............................... 57
Remapping Colored Buttons .................................... 57
Remote Control Codes
for Onkyo Components Connected via RI ............. 58
Resetting the REMOTE MODE Buttons ................... 58
Resetting the Remote Controller .............................. 58
Controlling Other Components ................................. 58
Using the Onkyo Dock.............................................. 61
Controlling Your iPod/iPhone ................................... 62
Appendix
Troubleshooting ......................................................... 63
Firmware Update ........................................................ 68
About HDMI................................................................. 71
Network/USB Features............................................... 72
License and Trademark Information ........................ 74
Specifications ............................................................. 75
Advanced Operations
On-screen Setup......................................................... 41
Using the Quick Setup .............................................. 41
Using the Audio Settings of Quick Setup.................. 42
Using the Setup Menu (HOME) ................................ 44
Setup Menu Items..................................................... 44
1. HDMI Input............................................................ 45
2. Component (Component Video Input) .................. 46
3. Digital Audio (Digital Audio Input) ......................... 46
4. Sp Config (Speaker Configuration)....................... 46
5. Sp Distance (Speaker Distance)........................... 47
6. Level Cal (Level Calibration)................................. 48
7. Audio Adjust.......................................................... 48
8. Source Setup ........................................................ 49
9. Hardware .............................................................. 51
10. HDMI Setup ........................................................ 52
11. Network Setup .................................................... 54
Zone 2 .......................................................................... 56
Making Zone 2 Connections ..................................... 56
Controlling Zone 2 Components ............................... 56
En-5
To reset the AV receiver, see page 63.
Safety Information and Introduction
Features
Amplifier
• 80 Watts/Channel @ 8 ohms (FTC)
• 130 Watts/Channel @ 6 ohms (IEC)
• 160 Watts/Channel @ 6 ohms (JEITA)
• WRAT–Wide Range Amplifier Technology
(5 Hz to 100 kHz bandwidth)
• Optimum Gain Volume Circuitry
• H.C.P.S. (High Current Power Supply) Massive
High Power Transformer
Processing
• HDMI (Audio Return Channel, 3D, DeepColor,
x.v.Color, Lip Sync, 4K Passthrough, DTS-HD
Master Audio, DTS-HD High Resolution Audio,
Dolby TrueHD, Dolby Digital Plus, DSD and MultiCH PCM)
• Dolby TrueHD and DTS-HD Master Audio
• Non-Scaling Configuration
• A-Form Listening Mode Memory
• Direct Mode
• Pure Audio Mode (European, Australian and Asian
models)
• Music Optimizer for Compressed Digital Music files
• Phase Matching Bass System
• 192 kHz/24-bit D/A Converters
• Powerful and Highly Accurate 32-bit Processing
DSP
• Jitter Cleaning Circuit Technology
Connections
Miscellaneous
• 6 HDMI Inputs and 1 Output
• 4K Passthrough-compatible HDMI Inputs
• Onkyo p for System Control
• 3 Digital Inputs (1 Optical/2 Coaxial)
• Component Video Switching (2 Inputs/1 Output)
• Banana Plug-Compatible Speaker Posts
• 40 FM/AM Presets
• Audyssey MultEQ® to correct room acoustic
problems
• Audyssey Dynamic EQ® for loudness correction
• Audyssey Dynamic Volume® to maintain optimal
listening level and dynamic range
• Crossover Adjustment
(40/50/60/70/80/90/100/120/150/200 Hz)
• A/V Sync Control Function (up to 400 ms)
• Auto Standby Function
• On-Screen Display via HDMI
• Preprogrammed u-Compatible Remote
*
In Europe, using banana plugs to connect speakers to an
audio amplifier is prohibited.
• Internet Radio Connectivity
• Network Capability for Streaming Audio Files
• 2 USB Inputs (Front/Rear) for Memory Devices and
iPod®/iPhone® models
* Only the front-panel USB input is compatible with
iPod/iPhone, Onkyo wireless LAN adapter UWF-1, and
Onkyo Bluetooth USB adapter UBT-1.
En-6
Safety Information and Introduction
Front & Rear Panels
Front Panel
(North American and Taiwanese models)
a
n o
b c
(European, Australian and Asian models)
de
p
f g h i j k l
q
m
r
v
w
s tu
For detailed information, see the pages in
parentheses.
h TUNING MODE button (32)
p TONE and Tone Level buttons (42)
i DISPLAY button (39)
q Input selector buttons (24)
a 8ON/STANDBY button (20)
j HOME button (40)
r AUX INPUT AUDIO/VIDEO jacks
b ZONE 2, OFF buttons (56)
s USB port (26, 27)
c Remote control sensor (10)
k TUNING q/w (32), PRESET e/r (32), cursor
and ENTER buttons
t SETUP MIC jack (22)
d Display (8)
l RETURN button
u HYBRID STANDBY indicator (20)
e LISTENING MODE buttons (35)
m MASTER VOLUME control (24)
f DIMMER button (North American and
Taiwanese models) (39)
n MUSIC OPTIMIZER button and indicator (North
American and Taiwanese models) (43)
v PURE AUDIO button and indicator (European,
Australian and Asian models) (35)
g MEMORY button (32)
o PHONES jack (19)
En-7
w RT/PTY/TP button (European, Australian and
Asian models) (33)
Safety Information and Introduction
Display
s
ab c d
f g
e
jklm j d
For detailed information, see the pages in
parentheses.
n
c Headphone indicator (19)
h Tuning indicators
RDS indicator (excluding North American and
Taiwanese models) (33)
AUTO indicator (32)
TUNED indicator (32)
FM STEREO indicator (32)
d 1, 3 and cursor indicators (26)
i MUTING indicator (39)
e Listening mode and format indicators (35, 51)
j Input indicators (17)
HDMI indicator (53)
DIGITAL indicator
a Z2 (Zone 2) indicator (56)
b 3D indicator
This lights when a 3D input signal is detected.
f Audyssey indicator (21, 49)
Dynamic EQ indicator (49)
Dynamic Vol indicator (50)
k ARC (Audio Return Ch) indicator (53)
g M.Opt (Music Optimizer) indicator (43)
l USB indicator (26, 27)
En-8
h
i
o p q
m NET indicator (27 to 30, 55)
n Message area
o SLEEP indicator (39)
p Channel/Unit indicators
ch indicator
Hz indicator
m/ft indicator
dB indicator
q ASb (Auto Standby) indicator (52)
Safety Information and Introduction
Rear Panel
(North American, European, Australian and Asian models)
a bc d
i
e
j
(Taiwanese models)
g
f
h
k lm
See “Connecting the AV Receiver” for connection
(➔ pages 11 to 19).
h Power cord (North American, European,
Australian and Asian models)
a u REMOTE CONTROL jack
i DIGITAL IN COAXIAL and OPTICAL jacks
b COMPONENT VIDEO IN and OUT jacks
d ETHERNET port
j Composite video and analog audio jacks
(BD/DVD IN, CBL/SAT IN, GAME IN, PC IN,
TV/CD IN)
e FM ANTENNA jack and AM ANTENNA terminal
k MONITOR OUT V jack
f HDMI IN and OUT jacks
l ZONE 2 LINE OUT jacks
g SPEAKERS terminals
(CENTER, FRONT, SURROUND)
m SUBWOOFER PRE OUT jacks
c USB port
n AC INLET (Taiwanese models)
En-9
n
Safety Information and Introduction
Remote Controller
Controlling the AV Receiver
To control the AV receiver, press RECEIVER to
select Receiver mode.
For detailed information, see the pages in
parentheses.
*2
a 8 RECEIVER button (20)
■ Aiming the remote controller
To use the remote controller, point it at the AV
receiver’s remote control sensor, as shown below.
b REMOTE MODE/INPUT SELECTOR buttons
(24)
These buttons can also be used when a REMOTE
MODE other than Receiver mode is selected.
c q/w/e/r and ENTER buttons
Remote control sensor
d Q SETUP button (41)
*2
a*2
b
f DIMMER button (39)
g MUTING button (39)
*1
RECEIVER
h DISPLAY button (39)
g *2
hc
i *2
i VOL q/w button (24)
ac
j
k
Approx. 16 ft. (5 m)
j RETURN button
k HOME button (40)
■ Installing the batteries
l SLEEP button (39)
d
d
AV receiver
e Listening Mode buttons (35)
Tip
• You can also use the remote controller to control Onkyo
Blu-ray Disc/DVD player, CD player, and other
components.
See “Entering Remote Control Codes” for more details
(➔ page 57).
■ Controlling the tuner
To control the AV receiver’s tuner, press AM or FM
(or RECEIVER).
e
Batteries (AA/R6)
a q/w buttons (32)
e
b D.TUN button (32)
c DISPLAY button
bf
l
d CH +/– button (33)
e Number buttons (32)
*1
To control a component, you must first enter the remote
control code.
See “Entering Remote Control Codes” for more details
(➔ page 57).
En-10
Note
• If the remote controller doesn’t work reliably, try replacing
the batteries.
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a long time,
remove the batteries to prevent damage from leakage or
corrosion.
• Remove expired batteries as soon as possible to prevent
damage from leakage or corrosion.
Connections
Speaker Configuration
Connections
Connecting the AV
Receiver
Connecting Your Speakers
Tip
The following table indicates the channels you should
use depending on the number of speakers that you
have.
No matter how many speakers you use, a powered
subwoofer is recommended for a really powerful and
solid bass.
To get the best from your surround sound system,
you need to set the speaker settings automatically
(➔ page 21) or manually (➔ page 46).
The speaker terminals are color-coded for
identification purpose.
Speaker
Color
Front left
White
Red
2
3
4
5
Front right
Front speakers
✔
✔
✔
✔
Center
Green
✔
Surround left
Blue
✔
Surround right
Gray
✔
Center speaker
✔
Surround speakers
Speaker Configuration
5.1-channel: a b c d e f
The supplied speaker cable labels are also colorcoded and you should attach them to the positive (+)
side of each speaker cable in accordance with the
table above. Then all you need to do is to match the
color of each label to the corresponding speaker
terminal.
f
Corner
position
1/3 of wall
position
de
Front
speakers
ab
Center speaker
c
d e Surround speakers
Subwoofer(s)
f
Attaching the Speaker Cable Labels
Number of speakers
Using Powered Subwoofers
ab c
• If your subwoofer is unpowered and you’re using an
external amplifier, connect the subwoofer pre out jack to an
input on the amplifier.
To find the best position for your subwoofer, while
playing a movie or some music with good bass,
experiment by placing your subwoofer at various
positions within the room, and choose the one that
provides the most satisfying results.
You can connect the powered subwoofer with two
SUBWOOFER PRE OUT jacks respectively.
The same signal is output from each jack.
En-11
Connections
Connecting the Speaker Cables/Powered Subwoofers
Before connecting the power cord, connect all of
your speakers and AV components.
Please connect a, b, c, d, e and f for 5.1-channel surround.
a
Front
speaker L
b
Front
speaker R
• Read the instructions supplied with your speakers.
• By default, speakers for 5.1-channel surround are
configured to use: front right/front left /center/
surround right/surround left/subwoofer.
■ Screw-type speaker terminals
Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the
ends of the speaker cables, and twist the bare wires
tightly, as shown.
c
Center speaker
1/2" to 5/8" (12 to 15 mm)
Red
Green
White
■ Banana Plugs (North American models)
• If you are using banana plugs, tighten the speaker
terminal before inserting the banana plug.
• Do not insert the speaker code directly into the
center hole of the speaker terminal.
Gray
Powered
subwoofer
f
Powered
subwoofer
f
Surround
speaker R
e
Blue
Surround
speaker L
d
• Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals only to positive (+)
terminals, and negative (–) terminals only to negative (–) terminals. If you get them the wrong way around, the
sound will be out of phase and will sound unnatural.
En-12
Connections
■ Speaker Connection Precautions
• You can connect speakers with an impedance of
between 6 and 16 ohms. If you use speakers with a
lower impedance, and use the amplifier at high
volume levels for a long period of time, the built-in
amp protection circuit may be activated.
• Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
• Be careful not to short the positive and negative
wires. Doing so may damage the AV receiver.
• Make sure the metal core of the wire does not have
contact with the AV receiver’s rear panel. Doing so
may damage the AV receiver.
• Don’t connect more than one cable to each speaker
terminal. Doing so may damage the AV receiver.
• Don’t connect one speaker to several terminals.
En-13
Connections
Connecting the TV/AV components
Connections
Before connecting the power cord, connect all of your speakers and AV components. To display the setup
menu on the TV screen, connecting the TV to the HDMI OUT is required.
A Use this jack to connect to the HDMI input of the
TV. If your TV doesn’t support Audio Return
Channel (ARC)*1, you need to connect an optical
digital cable together with the HDMI cable to jack
E.
E
I F
G
H
D
C
B
A
*1
ARC is the function that carries the audio signal
from the TV to jack A. With ARC, a single HDMI
cable can connect the TV and the AV receiver.
B Use this jack to connect to your Blu-ray Disc/DVD
player, etc.
C Use this jack to connect to the Satellite/cable settop box, etc.
D Use this jack to connect to the game consoles,
etc.
F Use this port to connect to a LAN port on a router
so the AV receiver can be connected to your
home network.
If you select the input selector button, the signal from
the component connected to the assigned jack is
played.
B
C
D
• Before making any AV connections, read the
manuals supplied with your AV components.
• Push plugs in all the way to make good connections
(loose connections can cause noise or
malfunctions).
• To prevent interference, keep audio and video
cables away from power cords and speaker cables.
Input
selector
buttons
G Use jack and terminal here to connect the
supplied FM antenna and AM loop antenna.
H Use this jack to make connections using an
analog audio cable.
With this connection, you can also enjoy analog
audio from external components while you are in
Zone 2.
I Use this jack to make connections using a
component video cable.
Tip
• To listen to the audio of a component connected via HDMI
through your TV’s speakers, enable “HDMI Through”
(➔ page 53) and set the AV receiver to standby mode.
• In the case of Blu-ray Disc/DVD players, if no sound is
output despite following the above-mentioned procedure,
set your Blu-ray Disc/DVD player’s HDMI audio settings to
PCM.
En-14
Connections
• If a phono equalizer is not installed on the turntable to
connect, it has to be prepared separately. Use a phono
equalizer which is compatible with the cartridge of the
turntable.
• Only the front-panel USB input is compatible with
iPod/iPhone and Onkyo wireless LAN adapter UWF-1.
UWF-1 can be used with the contents of not more than
64 kHz, not compatible with Dolby TrueHD and DSD.
Connecting to the Network (Optional)
The following diagram shows how you can connect
the AV receiver to your home network. In this
example, it’s connected to a LAN port on a router,
which has a 4-port 100Base-TX switch built-in.
Internet radio
WAN
Router
Modem
p
The AV receiver allows interoperability of the CEC
(Consumer Electronics Control) specified in the HDMI
standard, which is known as RIHD. Various linked
operations can be performed by connecting the AV
receiver to an RIHD-compatible TV, player, or
recorder.
Default setting is set to off, so it is required to change
the setting to on.
LAN
About RIHD-compatible components
The following components are p-compatible
(As of January 2013).
Computer or media server
Do not connect the AV receiver’s USB port to a USB
port on your computer. Music on your computer
cannot be played through the AV receiver in this way.
The default of the assignment for the input selector buttons and jacks are as shown below. These settings can
be changed. (The assignment for the composite video jacks and the analog audio jacks cannot be changed.)
Input selector buttons HDMI jacks
COMPONENT VIDEO
jacks
DIGITAL IN COAXIAL
and OPTICAL jacks
Composite video and
analog audio jacks
BD/DVD
HDMI IN 1
COMPONENT VIDEO
IN 1
DIGITAL IN
COAXIAL 1
VIDEO/AUDIO IN
BD/DVD
CBL/SAT
HDMI IN 2
COMPONENT VIDEO
IN 2
DIGITAL IN
COAXIAL 2
VIDEO/AUDIO IN
CBL/SAT
GAME
HDMI IN 3
PC
HDMI IN 4
VIDEO/AUDIO IN
GAME
VIDEO/AUDIO IN PC
AUX
TV/CD
VIDEO/AUDIO IN AUX
DIGITAL IN OPTICAL
En-15
AUDIO IN TV/CD
■ TV
• Sharp TV
■ Players/Recorders
• Onkyo and Integra p-compatible players
• Toshiba players and recorders
• Sharp players and recorders (only when used
together with Sharp TV)
*
Models other than those mentioned above may have some
interoperability if compatible with CEC, which is part of the
HDMI Standard, but operation cannot be guaranteed.
Note
• For proper linked operations, do not connect more
p-compatible components than the quantities
specified below, to the HDMI input terminal.
– Blu-ray Disc/DVD players: up to three.
– Blu-ray Disc/DVD recorders/Digital Video Recorders: up
to three.
– Cable/Satellite Set-top boxes: up to four.
• Do not connect the AV receiver to another AV receiver/AV
amplifier via HDMI.
• Proper linked operations are not guaranteed when more
p-compatible components than the abovementioned quantities are connected.
Connections
Operations that can be performed with
RIHD connection
■ For p-compatible TV
The following linked operations are enabled by
connecting the AV receiver to an p-compatible
TV.
• The AV receiver will enter standby mode when the
TV is set to standby.
• You can set on the menu screen of the TV to either
output the audio from the speakers connected to the
AV receiver, or from the speakers of the TV.
• It is possible to output the audio coming from the
tuner or auxiliary input of your TV to the speakers of
the AV receiver. (A connection such as an optical
digital cable or similar is required in addition to the
HDMI cable.)
• Input to the AV receiver can be selected with the
remote controller of the TV.
• Operations such as volume adjustment or similar for
the AV receiver can be performed from the remote
controller of the TV.
■ For p-compatible players/recorders
The following linked operations are enabled by
connecting the AV receiver to an p-compatible
player/recorder.
• When playback is started on the player/recorder, AV
receiver will switch to the HDMI input of the
player/recorder that is playing back.
• Operation of the player/recorder is possible using
the remote controller supplied with the AV receiver.
*
Depending on the model used, not all operations may be
available.
Note
• Do not assign an HDMI IN to the TV/CD selector at this
time, otherwise appropriate CEC (Consumer Electronics
Control) operation will not be guaranteed.
Confirm the settings
1. Turn on the power for all connected components.
2. Turn off the power of the TV, and confirm that the
power of the connected components is turned off
automatically with the link operation.
3. Turn on the power of the Blu-ray Disc/DVD
player/recorder.
4. Start playback on the Blu-ray Disc/DVD
player/recorder, and verify the following:
• The AV receiver automatically turns on, and
selects the input to which the Blu-ray Disc/DVD
player/recorder is connected.
• The TV automatically turns on, and selects the
input to which the AV receiver is connected.
5. Following the operating instructions of the TV,
select “Use the TV speakers” from the menu
screen of the TV, and confirm that the audio is
output from the speakers of the TV, and not from
the speakers connected to the AV receiver.
6. Select “Use the speakers connected from the AV
receiver” from the menu screen of the TV, and
confirm that the audio is output from the speakers
connected to the AV receiver, and not from the TV
speakers.
Note
• Audio from DVD-Audio or Super Audio CD may not output
from the TV speakers. You will be able to output the audio
from the TV speakers by setting the audio output of the
DVD player to 2ch PCM. (It may not be possible depending
on the player models.)
• Even if you set to output audio on the TV speakers, audio
will be output from the speakers connected to the AV
receiver when you adjust the volume or switch the input on
the AV receiver. To output audio from the TV speakers, redo the corresponding operations on the TV.
• In case of an p connection with u and u audio
control compatible components, do not connect the u
cable at the same time.
En-16
• On the TV, when you select anything other than the HDMI
jack to which the AV receiver is connected, the input on the
AV receiver will be switched to “TV/CD”.
• The AV receiver will automatically power on in conjunction
when it determines it to be necessary. Even if the AV
receiver is connected to an p compatible TV or
player/recorder, it will not power on if it is not necessary. It
may not power on in conjunction when the TV is set to
output audio from the TV.
• Linked functions with the AV receiver may not work
depending on the component model connected. In such
cases, operate the AV receiver directly.
Connections
Connection Tips
*2
Video Signal Flow Chart
Blu-ray Disc/DVD player, etc.
The video and audio signal flow
Tip
Connect the AV receiver between the AV
components and the TV. The signal from the AV
components is carried through the AV receiver. You
can enjoy the audio of the TV through the AV
receiver.
Composite
Component
HDMI
• When a signal is input via HDMI and the corresponding
input selector is selected, the HDMI indicator lights. In the
case of an optical or coaxial connection, the DIGITAL
indicator lights. In the case of an analog connection, neither
of the HDMI and DIGITAL indicators light.
HDMI
AV Cables and Jacks
IN
AV receiver
MONITOR OUT
Blu-ray Disc/DVD player, etc.
Composite
Component
■ HDMI
HDMI connections can carry digital video and audio.
TV, projector, etc.
Video, audio
AV receiver
Audio
Video, audio
TV, projector, etc.
Audio components can be connected by using any of
the following audio connection formats: analog,
optical, coaxial, or HDMI.
When choosing a connection format, bear in mind
that the AV receiver does not convert digital input
signals for analog line outputs and vice versa.
If signals are present at more than one input, the
inputs will be selected automatically in the following
order of priority: HDMI, digital, analog.
Note
Audio Signal Flow Chart
• The on-screen menus are displayed when:
– There is no video input, or
– The video input is 480p, 576p, 720p, 1080i, or 1080p.
Blu-ray Disc/DVD player, etc.
Analog
Video components can be connected by using any
one of the following video connection formats:
composite video, component video, or HDMI, the
latter offering the best picture quality.
Coaxial
Optical
IN
AV receiver
*1
*1
*1
Y
Green
CB/PB
Blue
CR/PR
Red
Yellow
OUT
*1
TV, projector, etc.
*1
■ Component video
Component video separates the luminance (Y) and
color difference signals (PB, PR), providing the best
picture quality (some TV manufacturers label their
component video sockets slightly differently).
■ Composite video
Composite video is commonly used on TVs, DVDs,
and other video equipment.
HDMI
HDMI
When choosing a connection format, bear in mind
that the AV receiver doesn’t convert between formats,
so only outputs of the same format as the input will
output the signal.
This is possible when “Audio Return Ch” is set to “Auto”
(➔ page 53), the TV/CD input selector is selected, and
your TV is ARC capable.
Depends on the “Audio TV Out” setting (➔ page 53).
En-17
*2
■ Optical digital audio
Optical digital connections allow you to enjoy digital
sound such as PCM*1, Dolby Digital or DTS. The
audio quality is the same as coaxial.
Connections
■ Coaxial digital audio
Coaxial digital connections allow you to enjoy digital
sound such as PCM*1, Dolby Digital or DTS. The
audio quality is the same as optical.
Orange
Connecting the Antennas
This section explains how to connect the supplied indoor FM antenna and AM loop antenna.
The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the
antenna to use the tuner.
■ Analog audio (RCA)
Analog audio connections (RCA) carry analog audio.
(North American and
Taiwanese models)
(European, Australian
and Asian models)
Insert the plug fully
into the jack.
Insert the plug fully
into the jack.
White
Red
Push.
*1
For PCM signals, the supported sampling rates are
32/44.1/48/88.2/96 kHz. With HDMI connections, 176.4
and 192 kHz are also supported.
Note
Insert wire.
Release.
Assembling the AM loop antenna
Caution
• Be careful not to injure
yourself when using
thumbtacks.
• The AV receiver does not support SCART plugs.
• The AV receiver’s optical digital jacks have shutter-type
covers that open when an optical plug is inserted and close
when it’s removed. Push plugs in all the way.
Thumbtacks, etc.
Caution
• To prevent shutter damage, hold the optical plug
straight when inserting and removing.
AM loop antenna (supplied)
Indoor FM antenna (supplied)
Note
• Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best
possible reception.
• Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.
Tip
• If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna
instead.
• If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available
outdoor AM antenna.
En-18
Connections
Connecting Onkyo RI Components
1
Make sure that each Onkyo component is
connected with an analog audio cable
(connection H in the hookup examples)
(➔ page 14).
2
3
Make the u connection (see the illustration).
Using Headphones
1
While the headphones plug is inserted in the
PHONES jack, = indicator lights.
Note
If you’re using an RI Dock, or cassette tape
deck, change the Input Display (➔ page 39).
With u (Remote Interactive), you can use the
following special functions:
e.g., cassette tape deck
■ System On/Auto Power On
When you start playback on a component
connected via u, while the AV receiver is on
standby, the AV receiver will automatically turn on
and select that component as the input source.
■ Direct Change
When playback is started on a component
connected via u, the AV receiver automatically
selects that component as the input source.
■ Remote Control
You can use the AV receiver’s remote controller to
control your other u-capable Onkyo components,
pointing the remote controller at the AV receiver’s
remote control sensor instead of the component.
You must enter the appropriate remote control code
first (➔ page 58).
Connect a pair of stereo headphones with a
standard plug (1/4 inch or ø 6.3 mm) to the
PHONES jack.
R
L
ANALOG
AUDIO OUT
R
L
ANALOG
AUDIO OUT
RI Dock
Note
• Use only u cables for u connections. u cables are
supplied with Onkyo components.
• Some components have two u jacks. You can connect
either one to the AV receiver. The other jack is for
connecting additional u-capable components.
• Connect only Onkyo components to u jacks. Connecting
other manufacturer’s components may cause a
malfunction.
• Some components may not support all u functions. Refer
to the manuals supplied with your Onkyo components.
• While Zone 2 is on, the System On/Auto Power On and
Direct Change u functions do not work.
En-19
• Always turn down the volume before connecting your
headphones.
• While the headphones plug is inserted in the PHONES
jack, the speakers are turned off. (The Zone 2
speakers are not turned off.)
• When you connect a pair of headphones, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct, or Pure Audio (European, Australian
and Asian models).
• If you connect an iPod or iPhone to the USB port on
the AV receiver, no sound will be output from the
headphones jack.
Turning On & Basic Operations
Turning On & Basic
Operations
the same circuit. If this is a problem, plug the AV receiver
into a different branch circuit.
• Do not use a power cord other than the one supplied with
the AV receiver. The supplied power cord is designed
exclusively for use with the AV receiver and should not be
used with any other equipment.
• Never disconnect the power cord from the AV receiver
while the other end is still plugged into a wall outlet. Doing
so may cause an electric shock. Always disconnect the
power cord from the wall outlet first, and then the AV
receiver.
Turning On
Turning On/Off the AV
Receiver
1
Press RECEIVER followed by 8RECEIVER on
the remote controller.
The AV receiver comes on and its display lights.
Connecting the Power Cord
1
When a new version of the firmware is available, the
notification window “Update New F/W” pops up. This
notification only appears when the AV receiver is
connected to the Internet (➔ page 15). To perform
the firmware update, follow the instructions on
screen.
Use q/w and ENTER on the AV receiver or remote
controller to select one of the options.
`Update Now:
Starts the firmware update.
Refer to “Firmware Update” (➔ page 68).
`Remind me Later:
The update notification will pop up again the
next time you turn the AV receiver on.
`Never Remind me:
Disables the automatic update notification.
Tip
(Taiwanese models)
Connect the supplied power cord to the AV
receiver’s AC INLET.
To AC wall outlet
2
Press 8ON/STANDBY on the front panel.
or
Firmware Update Notification
Plug the power cord into an AC wall outlet.
Note
• Before connecting the power cord, connect all of your
speakers and AV components.
• Turning on the AV receiver may cause a momentary power
surge that might interfere with other electrical equipment on
• The update notification window can be enabled or disabled
in “Update Notice” (➔ page 55).
Turning Off
1
Press 8ON/STANDBY on the front panel.
or
Press RECEIVER followed by 8RECEIVER on
the remote controller.
The AV receiver will enter standby mode. To
prevent any loud surprises when you turn on the
AV receiver, always turn down the volume before
you turn it off.
Tip
• The HYBRID STANDBY indicator may light depending on
the status of settings.
• For details on power management settings, see “Auto
Standby” (➔ page 52).
En-20
About the HYBRID STANDBY indicator
By way of optimized circuitry, this function reduces
power consumption when the AV receiver is in
standby mode. The HYBRID STANDBY indicator will
light in either of the following conditions:
–“HDMI Through” is enabled and Zones are turned
off (the HDMI indicator is off).
–“Network Standby” is enabled and Zones are
turned off (the NET indicator is off).
Turning On & Basic Operations
Using the Automatic Speaker Setup
With the supplied calibrated microphone,
Audyssey MultEQ® automatically determines the
number of speakers connected, their size for
purposes of bass management, optimum crossover
frequencies to the subwoofer (if present), and
distances from the primary listening position.
Audyssey MultEQ then removes the distortion caused
by room acoustics by capturing room acoustical
problems over the listening area in both the frequency
and time domain. The result is clear, well-balanced
sound for everyone. Audyssey MultEQ can be used
with Audyssey Dynamic EQ® and
Audyssey Dynamic Volume® (➔ pages 49, 50).
Before using this function, connect and position all of
your speakers.
Audyssey MultEQ offers two ways of measuring: the
“Audyssey Quick Start” and “Audyssey MultEQ
Full Calibration”.
• “Audyssey Quick Start” uses the measurement
from one position to perform the speaker setting
only.
• “Audyssey MultEQ Full Calibration” uses the
measurement from six positions to correct room
response in addition to the speaker setting.
The more positions are used in measuring, the better
the listening environment will become. We
recommend using a measurement from six positions
to create the best listening environment.
The Quick Start takes 2 minutes and Full Calibration
takes about 15 minutes.
Total measurement time varies depending on the
number of speakers.
Measurement procedure
To create a listening environment in your home
theater that all listeners will enjoy, Audyssey MultEQ
takes measurements at up to six positions within the
listening area. Position the microphone at ear height
of a seated listener with the microphone tip pointed
directly at the ceiling using a tripod. Do not hold the
microphone in your hand during measurements as
this will produce inaccurate results.
■ First measurement position
Also referred to as the Main Listening Position, this
refers to the most central position where one would
normally sit within the listening environment.
Audyssey MultEQ uses the measurements from this
position to calculate speaker distance, level, and the
optimum crossover value for the subwoofer.
■ Second-sixth measurement positions
These are the other listening positions (i.e., the
places where the other listeners will sit). You can
measure up to six positions.
TV
def
cab
: Listening area
a to f: Listening position
En-21
Note
• Make the room as quiet as possible. Background noise and
Radio Frequency Interference (RFI) can disrupt the room
measurements. Close windows, televisions, radios, air
conditioners, fluorescent lights, home appliances, light
dimmers, or other devices. Turn off the cell phone (even if
it is not in use) or place it away from all audio electronics.
• The microphone picks up test tones played through each
speaker as Audyssey MultEQ Room Correction and
Speaker Setup runs.
• Audyssey MultEQ Room Correction and Speaker Setup
cannot be performed while a pair of headphones is
connected.
Turning On & Basic Operations
1
Turn on the AV receiver and the connected TV.
On the TV, select the input to which the AV
receiver is connected.
2
Set the speaker setup microphone at the Main
Listening Position a, and connect it to the
SETUP MIC jack.
4
Note
5
Use q/w to select “Audyssey Quick Start” or
“Audyssey MultEQ Full Calibration”, and then
press ENTER.
6
Press ENTER.
Audyssey MultEQ® Room Correction and
Speaker Setup starts.
Test tones are played through each speaker as
Audyssey MultEQ Room Correction and Speaker
Setup runs. This process takes a few minutes.
Please refrain from talking during
measurements and do not stand between
speakers and the microphone.
Do not disconnect the speaker setup microphone
during Audyssey MultEQ Room Correction and
Speaker Setup, unless you want to cancel the
setup.
If you select “Audyssey Quick Start”, you will go
to step 9.
The speaker setting menu appears.
Note
• The on-screen menus appear only on a TV that is
connected to HDMI OUT. If your TV is connected to
other video outputs, use the AV receiver’s display
when changing settings.
When you’ve finished making the settings,
press ENTER.
Subwoofer
Audyssey
Yes
Perform the “4. Sp Config (Speaker
Configuration)” according to your speaker
configuration:
– Subwoofer (➔ page 46)
Use q/w to select an option, and then press
ENTER.
Audyssey
MultEQ: Auto Setup
Subwoofer
Front
Center
Surround
Crossover
• If your subwoofer does not have a volume control,
disregard the displayed level and press ENTER to
proceed to the next step.
• If you set the subwoofer’s volume control to its
maximum and the level displayed is lower than 75 dB,
leave the subwoofer’s volume control at its maximum
and press ENTER to proceed to the next step.
Speaker setup microphone
MultEQ: Auto Setup
9
<- Review Speaker Configuration ->
SETUP MIC jack
3
Adjust the subwoofer volume level to 75 dB,
and then press ENTER.
Test tones are played through the subwoofer.
Use the volume control on the subwoofer.
7
If you use a powered subwoofer(s), go to step 4.
If not, go to step 5.
8
Place the speaker setup microphone at the
next position, and then press ENTER.
Audyssey MultEQ performs more
measurements. This takes a few minutes.
When prompted, repeat step 7.
En-22
:
:
:
:
:
Yes
Small
Small
Small
100Hz
Save
Cancel
The options are:
` Save:
Save the calculated settings and exit
Audyssey MultEQ Room Correction and
Speaker Setup.
` Cancel:
Cancel Audyssey MultEQ Room Correction
and Speaker Setup.
Tip
• You can view the calculated settings for the speaker
configuration, speaker distances, and speaker levels
by using e/r.
10
Use q/w to select a target, and use e/r to
change the setting.
After the results of Audyssey MultEQ have been
saved, the menu will display the “Audyssey”
(➔ page 49), “Dynamic EQ” (➔ page 49),
“Dynamic Volume” (➔ page 50) settings.
Note
• When “Audyssey Quick Start” has been used for
measurement, “Audyssey” cannot be selected.
• These settings are applied to all input selectors.
11
12
Press ENTER.
Disconnect the speaker setup microphone.
Turning On & Basic Operations
Note
• You can cancel Audyssey MultEQ® Room Correction and
Speaker Setup at any point in this procedure simply by
disconnecting the setup microphone.
• Do not connect or disconnect any speakers during
Audyssey MultEQ Room Correction and Speaker Setup.
• If the AV receiver is muted, it will be unmuted automatically
when Audyssey MultEQ Room Correction and Speaker
Setup starts.
• Changes to the room after Audyssey MultEQ Room
Correction and Speaker Setup requires you run
Audyssey MultEQ Room Correction and Speaker Setup
again, as room EQ characteristics may have changed.
Error Messages
While Audyssey MultEQ Room Correction and
Speaker Setup is in progress, one of the error
messages below may appear.
Using a Powered Subwoofer
Audyssey
MultEQ: Auto Setup
Ambient noise is too high.
Error message
Retry
Cancel
The options are:
` Retry:
Try again.
` Cancel:
Cancel Audyssey MultEQ Room Correction and
Speaker Setup.
• Ambient noise is too high.
The background noise is too loud. Remove the
source of the noise and try again.
• Speaker Matching Error!
The number of speakers detected was different
from that of the first measurement. Check the
speaker connection.
• Writing Error!
This message appears if saving fails. Try saving
again. If this message appears after 2 or 3
attempts, contact your Onkyo dealer.
• Speaker Detect Error
This message appears if a speaker is not detected.
“No” means that no speaker was detected.
Tip
• See “Speaker Configuration” for appropriate settings
(➔ page 11).
En-23
The setup of the speaker can be done manually
(➔ page 46).
The setup of the volume level of each speaker also
can be done manually (➔ pages 47, 48).
If you’re using a powered subwoofer and it outputs
very low-frequency sound at a low volume level, it
may not be detected by Audyssey MultEQ Room
Correction and Speaker Setup.
If the “Subwoofer” appears on the “Review Speaker
Configuration” screen as “No”, increase the
subwoofer’s volume to the half-way point, set it to its
highest crossover frequency, and then try running
Audyssey MultEQ Room Correction and Speaker
Setup again. Note that if the volume is set too high
and the sound distorts, detection issues may occur,
so use an appropriate volume level. If the subwoofer
has a low-pass filter switch, set it to Off or Direct.
Refer to your subwoofer’s instruction manual for
details.
Playback
* For the CEC compatible TV and the AV components
connected with HDMI connections, switching the input
is automatically performed. Switch the input manually
for other AV components.
1
2
Playback
4
Select the desired listening mode.
You can enjoy various types of listening mode.
The listening mode is switched by pressing
Listening mode button on the AV receiver or the
remote controller.
4
Adjust the volume.
You can enjoy the surround sound.
3
Playback
This section describes the basic operation such as
playback, listening mode, and other useful functions.
Reading this manual from the beginning to this
section helps you to understand the basic
connection/setup/operation.
See also:
• “Playing an iPod/iPhone via USB” (➔ page 26)
• “Playing a USB Device” (➔ page 27)
• “Listening to TuneIn” (➔ page 27)
• “Registering Other Internet Radio” (➔ page 28)
• “Playing Music Files on a Server (DLNA)”
(➔ page 29)
• “Playing Music Files on a Shared Folder”
(➔ page 30)
• “Remote Playback” (➔ page 31)
• “Listening to AM/FM Radio” (➔ page 32)
• “Playing Audio and Video from Separate Sources”
(➔ page 34)
• “Controlling Other Components” (➔ page 57)
• “Using the Onkyo Dock” (➔ page 61)
3
Tip
1
1
2
3
4
Turn on the AV receiver, the TV and the AV
components.
* When you operate the AV receiver with the remote
controller, press the RECEIVER button first.
2
Select the input on the AV receiver to play the
AV components.
Press the input selector button to which the AV
components to be played is connected.
Press the TV/CD button to play the audio of the
TV. Switching the input on the TV is also
required. Select the input to which the AV
receiver is connected by using the TV remote
controller.
En-24
• When listening to an HDMI component through the AV
receiver, set the HDMI component so that its video can be
seen on the TV screen (on the TV, select the input of the
HDMI component connected to the AV receiver). If the TV
power is off or the TV is set to another input source, this
may result in no sound from the AV receiver or the sound
may be cut off.
Playback
Controlling Contents of USB or
Network Devices
(➔ page 26)
Press USB or NET first.
a TOP MENU
This button displays the top menu for each media or
service.
b q/w and ENTER
These buttons navigate through the menus.
e/r
This button cycles through pages.
PLAYLIST e/r
In Standard Mode (iPod/iPhone), this button selects
playlists.
c 1
This button starts playback.
a
b
c
d
e
f
g
h
d 7
This button selects the beginning of the current song.
Pressing this button twice selects the previous song.
i
e 5
This button fast-reverses the current song.
j
k
l
m
n
o
p
q
f 3
This button pauses playback.
g SEARCH
You can toggle between the playback screen and the
list screen during playback.
h DISPLAY
This button switches between song information during
playback.
Press this button while the list screen is displayed to
return to the playback screen.
i ALBUM +/–
In Standard Mode (iPod/iPhone), this button selects
albums.
j MENU
This button displays the menu of Internet radio
services.
k RETURN
This button returns to the previous menu.
l 4
This button fast-forwards the current song.
En-25
m 6
This button selects the next song.
n 2
This button stops playback.
o MODE
You can switch between Standard Mode and Extended
Mode (iPod/iPhone).
p RANDOM
This button performs random playback.
q REPEAT
Press this button repeatedly to cycle through the repeat
modes.
Tip
• See “Controlling Other Components” about the operation of
other components (➔ page 57).
Note
• The buttons you can use will differ depending on the
devices and media used for playback.
Playback
Understanding Icons on the Display
This section describes icons that appear on the AV
receiver’s display during media playback.
Icon
Description
Folder
Track
Playback
Pause
Tip
• The on-screen menus appear only on a TV that is
connected to the HDMI OUT.
This section explains how to play music files on the
iPod/iPhone.
Compatible iPod/iPhone models
Made for:
iPod touch (1st, 2nd, 3rd, 4th and 5th generation),
iPod classic, iPod nano (2nd, 3rd, 4th, 5th, 6th and
7th generation), iPhone 5, iPhone 4S, iPhone 4,
iPhone 3GS, iPhone 3G, iPhone
Fast Forward
Fast Reverse
4
Use q/w to select a music file, and press
ENTER or 1 to start playback.
Note
1
Press USB repeatedly to select the
“USB(Front)” input.
Tip
Artist
Album
• When you disconnect the iPod/iPhone, the AV
receiver remembers the current mode. This means
that if you disconnect when in Extended Mode, the AV
receiver will start in Extended Mode the next time you
connect the iPod/iPhone.
• You can also use the q/w, ENTER and TUNING
MODE buttons on the front panel. TUNING MODE
allows you to switch modes.
• When connecting your iPod/iPhone with a USB cable,
we recommend you use an official USB cable from
Apple Inc.
Playing an iPod/iPhone via USB
• The same operation can be done by selecting “USB”
in the Home menu.
2
Repeat One Track
Repeat Folder (USB Device)
Repeat
Shuffle
Shuffle Album (iPod/iPhone)
3
Connect the USB cable that comes with the
iPod/iPhone to the USB port on the front of the
AV receiver.
While reading the contents of your iPod/iPhone,
the message “Connecting...” appears on the AV
receiver’s display.
A list of your iPod/iPhone model’s contents
appears (Extended Mode).
The USB indicator lights. It will flash if the AV
receiver cannot read the iPod/iPhone.
Use q/w to select a folder, and then press
ENTER to open it.
Tip
• If you want to operate using the iPod/iPhone or the
remote controller, press MODE to switch to Standard
mode.
En-26
• While the message “Connecting...” appears on the AV
receiver’s display, do not disconnect the USB cable
supplied with your iPod/iPhone or the USB device from the
USB port.
• If you connect an iPod or iPhone to the USB port, no sound
will be output from the headphones jack.
Extended Mode Control
The content information is displayed (lists are
displayed), and you can control the content while
looking at the screen.
Top screen list:
Playlists, Artists, Albums, Genres, Songs,
Composers, Shuffle Songs, Now Playing.
Standard Mode Control
The content information is not displayed, but can be
operated using the iPod/iPhone or the remote
controller.
Playback
Playing a USB Device
Tip
• The on-screen menus appear only on a TV that is
connected to the HDMI OUT.
This section explains how to play music files from a
USB device (e.g., USB flash drives and MP3 players).
See also:
• “Network/USB Features” (➔ page 72)
1
Press USB repeatedly to select the
“USB(Front)” or “USB(Rear)” input.
2
Plug your USB device into the AV receiver’s
USB port.
The USB indicator lights. It will flash if the AV
receiver cannot read the USB device.
3
4
Listening to TuneIn
You need to connect the AV receiver to your home
network (➔ page 15).
Tip
• The on-screen menus appear only on a TV that is
connected to the HDMI OUT.
TuneIn is a new radio service which offers the music,
sports and news all over the world.
Over 70,000 radio stations and 2 million on-demand
programs are registered, and you can easily enjoy
them by selecting stations or programs of your
choice. TuneIn is preprogrammed on the AV receiver.
1
Press ENTER.
A list of the device’s contents appears. To open a
folder, use q/w to select it, and then press
ENTER.
Use q/w to select a music file, and press
ENTER or 1 to start playback.
Note
• While the message “Connecting...” appears on the AV
receiver’s display, do not disconnect the USB cable
supplied with your iPod/iPhone or the USB device from the
USB port.
Press NET.
The “NET” screen appears, and the NET indicator
lights. If it flashes, verify that the Ethernet cable is
firmly connected to the AV receiver.
Tip
• The same operation can be done by selecting
“Network Service” in the Home menu.
2
Use q/w to select “TuneIn” and then press
ENTER.
3
Use q/w to select a station or a program, and
then press ENTER.
Playback starts.
TuneIn
Track
Station
Info
:
:
:
News
Station name
Sports talk
0 : 11
Go to Menu
Either of the following menus can be selected by
pressing the MENU button on the remote controller or
pressing ENTER button to select “Go to Menu”.
`Add to My Presets
In this menu, stations or programs can be stored
in “My Presets”.
`Remove from My Presets
In this menu, stations or programs stored in “My
Presets” can be deleted.
`Report a problem
This menu is used to report problems on TuneIn
service or resolve the problems in a wizard style.
`View Schedule
In this menu, program listings of stations or
programs can be displayed.
`Clear recents
In this menu, all the stations and programs
stored in “Recents” can be deleted.
`Add to My Favorites
In this menu, stations or programs can be stored
in “My Favorites”.
Setting an TuneIn account
To create a user account for TuneIn, open a browser
window such as Internet Explorer®, and connect to
tunein.com website. With a TuneIn account, you can
quickly search and browse for stations and programs
at tunein.com website and save as your favorites
which will automatically appear in your AV receiver
My Presets account. If you have a TuneIn account,
select “Login” and then “I have a TuneIn account”
on the top list. Enter your user name and password to
login.
Tip
• Select “Login with a registration code”, and associate a
device from my page on TuneIn website by using a
registration code displayed on the screen. This allows you
to login without entering a user name and a password.
En-27
Playback
Adding TuneIn radio stations or programs to
My Favorites/My Presets
There are two ways you can register specific Internet
radio stations (programs) from the TuneIn.
• Adding to My Favorites
The selected program will be added to “My
Favorites” on the “NET” screen, which appears when
pressing NET.
1. Select radio stations or programs, and press
MENU button on the remote controller.
2. Use q/w to select “Add to My Favorites”, and
press ENTER.
3. Use q/w/e/r to select “OK”, and press ENTER.
Tip
• You can rename the stations saved in “My Favorites”
(➔ page 28).
• Adding TuneIn radio stations or programs to My
Presets
Select "TuneIn", and press ENTER button to display
a folder of “My Presets” on the screen that displays
Category/Area, etc. Store your favorite stations or
programs in this folder.
1. Select radio stations or programs, and press
MENU button on the remote controller.
2. Use q/w to select “Add to My Presets”, and
press ENTER.
Tip
Registering Other Internet Radio
You need to connect the AV receiver to your home
network (➔ page 15).
Tip
• The on-screen menus appear only on a TV that is
connected to the HDMI OUT.
Internet radio URLs in the following formats are
supported: PLS, M3U, and podcast (RSS). However,
depending on the type of data or audio format used
by the Internet radio station, you may not be able to
listen to some stations.
To listen to other Internet radio stations, you must
register your station in “My Favorites” of the “NET”
screen, as described below.
Note
• Services available may vary depending on the region. See
the separate instructions for more information.
• Certain network service or contents available through this
device may not be accessible in case the service provider
terminates its service.
1
Select “Network Setup” on the Setup menu to
verify your IP address (➔ page 54).
Take a note of the IP address.
2
3
On your computer, start your web browser.
4
Click on the “My Favorites” tab, and enter the
Internet radio station’s name and URL.
• If no radio stations or programs are stored in “My Presets”,
“My Presets” folder will not be displayed.
Enter the AV receiver’s IP address in the
browser’s Internet address (URL) field.
If you are using Internet Explorer®, you can also
enter the URL by selecting “Open...” on the “File”
menu.
Information on the AV receiver is then shown on
your Internet browser (Web Setup).
En-28
5
Click “Save” to save the Internet radio station.
The Internet radio station is then added to “My
Favorites”. To play the registered station, press
NET, and then select “My Favorites” on the
“NET” screen. A list of registered Internet radio
stations appears. Select the one that you saved
and press ENTER.
Tip
• If you want to add a new station directly from “My
Favorites”, select an empty slot in the list and press MENU.
Then, select “Create New Station” and press ENTER.
Pressing ENTER again will display the keyboard screen.
Use that keyboard to enter the station’s name and URL
respectively, and then press ENTER.
• If you want to delete a station saved in “My Favorites”,
press MENU with the station selected or while the station is
playing. Then, use q/w to select “Delete from My
Favorites” and press ENTER. You can also delete stations
from the Web Setup.
• If you want to rename a station, select the desired station
and press MENU. Then, use q/w to select “Rename this
station” and press ENTER.
• You can save up to 40 Internet radio stations.
Playback
Playing Music Files on a Server (DLNA)
• Windows Media Player 11 can be downloaded for free
from the Microsoft web site.
You need to connect the AV receiver to your home
network (➔ page 15).
Tip
• The on-screen menus appear only on a TV that is
connected to the HDMI OUT.
This section explains how to play music files on a
computer or media server through the AV receiver
(Server Playback).
Windows Media Player Setup
■ Windows Media Player 12 Setup
This section explains how to configure Windows
Media Player 12 so that the AV receiver can play the
music files stored on your personal computer.
1
2
■ Windows Media Player 11 Setup
This section explains how to configure Windows
Media Player 11 so that the AV receiver can play the
music files stored on your computer.
1
2
3
4
5
Tip
3
4
On the “Stream” menu, select “Turn on media
streaming”.
A dialog box appears.
3
4
Select the AV receiver in the list, and then
click “Allow”.
The corresponding icon will be checked.
5
Use q/w to select a server, and then press
ENTER.
The menu is displayed according to the server
functions.
Note
Move your cursor and click on “Turn on media
streaming”.
A list of media server appears. Wording may vary
slightly depending on the network location.
5
Use q/w to select an item, and then press
ENTER or 1 to start playback.
On the “Media streaming options”, select the
AV receiver and confirm that it is set to
“Allowed”.
DLNA
Track
Artist Name
Album Name
Click “OK” to close the dialog box.
This completes the Windows Media Player 12
configuration.
You can now play the music files in your
Windows Media Player 12 library.
Playing music files on a server (DLNA)
1
Use q/w to select “DLNA”, and press ENTER.
• The search function does not work with media servers
which do not support this function.
• Photos and movies stored on a media server cannot
be accessed from the AV receiver.
• Depending on the sharing settings in the media server,
the AV receiver may not able to access the content.
See the instruction manual of the media server.
• If the media streaming is already activated, clicking on
“More streaming options...” in the “Stream” menu will
display a list of the playback devices connected to the
network. You can skip step 3.
Select the “Share my media” check box, and
then click “OK”.
A list of the supported devices appears.
Click “OK” to close the dialog box.
This completes the Windows Media Player 11
configuration.
You can now play the music files in your
Windows Media Player 11 library through the AV
receiver.
Start Windows Media Player 12.
Press NET.
The “NET” screen appears. The NET indicator
lights. If it flashes, confirm the network
connection.
• The same operation can be done by selecting
“Network Service” in the Home menu.
Tip
Start Windows Media Player 11.
On the “Library” menu, select “Media
Sharing”.
The “Media Sharing” dialog box appears.
2
Tip
Start your computer or media server.
En-29
:
:
:
Track name
Artist name
Album name
0 : 11 / 2 : 00
Note
• Depending on the media server, 5/4/3 may not
work.
• If the message “No Item.” appears, this means that no
information can be retrieved from the server. In this
case, check your server, network, and AV receiver
connections.
Playback
Playing Music Files on a Shared Folder
This section explains how to play music files on a
computer or NAS (Network Attached Storage)
through the AV receiver.
5
Under “Network File and Folder Sharing”,
select “Share”.
6
Select “Everyone” from the pull-down menu,
click “Add”, and then click “Share”.
5
Tip
• The login information will be remembered for the next
time you log in.
• The login information is that of the user account set
when creating a shared folder.
Tip
Windows 8/Windows 7 Setup
• With this setting, everyone is allowed to access the
folder. If you want to assign a user name and
password to the folder, make the corresponding
settings for “Permissions” in “Advanced Sharing” of the
“Sharing” tab.
• Verify that “Workgroup” is properly set.
■ Setting the sharing options
1
Select “Choose homegroup and sharing
options” on the Control Panel.
Note
Tip
• When using NAS (Network Attached Storage), refer to
the instruction manual provided with your NAS unit.
• If this option is not available, verify that “View by:” is set
to “Category”.
2
3
4
Select “Change advanced sharing settings”.
Playing music files on a shared folder
Under “Home or Work”, verify that the
following items are checked:
“Turn on network discovery”, “Turn on file and
printer sharing”, “Turn on sharing so anyone with
network access can read and write files in the
Public folders”, and “Turn off password protected
sharing”.
In order to enjoy Home Media, you must first create a
shared folder on your computer.
1
Tip
Select “Save changes” and click “OK” on the
confirmation screen.
■ Creating a shared folder
1
2
3
Right-click the folder that you want to share.
4
Check the check box of “Share this folder”
and then click “OK”.
Select “Properties”.
Press NET.
The network service screen appears. The NET
indicator lights. If it flashes, confirm the network
connection.
• The same operation can be done by selecting
“Network Service” in the Home menu.
2
Use q/w to select “Home Media”, and press
ENTER.
3
Use q/w to select a server, and then press
ENTER.
Tip
On the “Sharing” tab, select “Advanced
Sharing”.
• The server name of your computer can be viewed on
the computer properties screen.
4
Use q/w to select the desired shared folder
and then press ENTER.
En-30
When asked for a user name and password,
enter the necessary login information.
6
Use q/w to select a music file and then press
ENTER or 1.
The playback of the selected file starts.
Playback
Remote Playback
5
You need to connect the AV receiver to your home
network (➔ page 15).
Tip
• The on-screen menus appear only on a TV that is
connected to the HDMI OUT.
Remote playback is supported by Windows Media
Player 12.
Remote Playback means you can play the music files
stored on a media server or personal computer with
the AV receiver by operating the controller device in
the home network.
Windows Media Player 12 Setup
This section explains how to configure Windows
Media Player 12 so that the AV receiver can play the
music files stored on your personal computer.
1
2
4
Using Remote Playback
1
2
3
Move your cursor and click on “Turn on media
streaming”.
A list of media server appears. Wording may vary
slightly depending on the network location.
On the “Media streaming options”, select the
AV receiver and confirm that it is set to
“Allowed”.
Turn on the AV receiver.
Start Windows Media Player 12.
To enable remote playback, you must first
configure Windows Media Player 12.
On Windows Media Player 12, right-click on a
music file.
The right-click menu appears.
Tip
• For selecting another media server, select the desired
media server from the “Other Libraries” menu on
Windows Media Player 12.
On the “Stream” menu, select “Turn on media
streaming”.
A dialog box appears.
• If the media streaming is already activated, clicking on
“More streaming options...” in the “Stream” menu will
display a list of the playback devices connected to the
network. You can skip step 3.
3
Tip
• On the “Stream” menu, confirm that “Allow remote
control of my Player...” is checked.
Start Windows Media Player 12.
Tip
Click “OK” to close the dialog box.
This completes the Windows Media Player 12
configuration.
You can now play the music files in your
Windows Media Player 12 library.
4
Select the AV receiver in “Remote playback”.
The “Play to” window appears and playback on
the AV receiver starts. Operations during remote
playback can be made from the “Play to” window
of Windows 8/Windows 7 on your personal
computer.
A playback screen will be displayed on the
connected TV.
Tip
• If the operating system of your personal computer is
Windows 8, click “Play to” and select the AV receiver.
En-31
5
Adjusting the Volume.
You can adjust the volume by adjusting the
volume bar in the “Remote playback” window.
The default maximum volume level is 64. If you
wish to change this, enter the value from the Web
Setup in your browser. Refer to step 3 of
“Registering Other Internet Radio” for details
(➔ page 28).
The volume value of the remote window and the
volume value of the AV receiver may not always
match.
Adjustments you make to the volume in the AV
receiver will not be reflected in the “Remote
playback” window.
Note
• Remote playback cannot be used in any of the following
cases:
– Network services are being used.
– Contents are being played from a USB device or
iPod/iPhone.
Playback
Listening to AM/FM Radio
2
This section describes the procedure of using the
buttons on the front panel, unless otherwise specified.
Press TUNING q/w.
Searching stops when a station is found.
When tuned into a station, the TUNED indicator
lights. When tuned into a stereo FM station, the
FM STEREO indicator lights as shown.
Using the Tuner
With the built-in tuner you can enjoy AM and FM radio
stations. You can store your favorite stations as
presets for quick selection.
You can also change the frequency steps
(➔ page 52).
1
FM STEREO
1
2
Tip
• Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may
be impossible to get good reception. In this case,
switch to manual tuning mode and listen to the station
in mono.
(Actual display depends on the country.)
■ Auto tuning mode
On the remote controller, press AM or FM to
select “AM” or “FM”, followed by D.TUN.
(Actual display depends on the country.)
Frequency
Tuning into Radio Stations
1
TUNED
AUTO
Press AM or FM to select either “AM” or “FM”.
In this example, FM has been selected.
Band
■ Tuning into stations by frequency
You can tune into AM and FM stations directly by
entering the appropriate frequency.
■ Manual tuning mode
In manual tuning mode, FM stations will be in mono.
1
Press TUNING MODE so that the AUTO
indicator lights on the AV receiver’s display.
2
Press TUNING MODE so that the AUTO
indicator goes off on the AV receiver’s
display.
Presetting AM/FM Stations
You can store a combination of up to 40 of your
favorite AM/FM radio stations as presets.
1
Tune into the AM/FM station that you want to
store as a preset.
See the previous section.
2
Press MEMORY.
The preset number flashes.
Press and hold TUNING q/w.
The frequency stops changing when you release
the button.
Press the buttons repeatedly to change the
frequency one step at a time.
(Actual display depends on the country.)
3
En-32
Within 8 seconds, use the number buttons to
enter the frequency of the radio station.
For example, to tune to 87.5 (FM), press 8, 7, 5
or 8, 7, 5, 0.
If you have entered the wrong number, you can
retry after 8 seconds.
While the preset number is flashing (about 8
seconds), use PRESET e/r to select a preset
from 1 through 40.
Playback
4
Press MEMORY again to store the station or
channel.
The station or channel is stored and the preset
number stops flashing.
Repeat this procedure for all of your favorite
AM/FM radio stations.
■ Selecting Presets
1
To select a preset, use PRESET e/r on the AV
receiver, or the remote controller’s CH +/–.
Tip
• You can also use the remote controller’s number
buttons to select a preset directly.
■ Deleting Presets
1
Select the preset that you want to delete.
See the previous section.
2
While holding down MEMORY, press TUNING
MODE.
The preset is deleted and its number disappears
from the AV receiver’s display.
Using RDS (excluding North American and
Taiwanese models)
When tuned into an RDS station, the RDS indicator
lights.
When the station is broadcasting text information, the
text can be displayed.
■ What is RDS?
RDS stands for Radio Data System and is a method of
transmitting data in FM radio signals. It was developed
by the European Broadcasting Union (EBU) and is
available in most European countries. Many FM
stations use it these days. In addition to displaying text
information, RDS can also help you find radio stations
by type (e.g., news, sport, rock, etc.).
Note
• RDS works only in areas where RDS broadcasts are
available.
• In some cases, the text characters displayed on the AV
receiver may not be identical to those broadcast by the
radio station. Also, unexpected characters may be
displayed when unsupported characters are received. This
is not a malfunction.
• If the signal from an RDS station is weak, RDS data may be
displayed intermittently or not at all.
■ Displaying Radio Text (RT)
1
Press RT/PTY/TP once.
The RT information scrolls across the AV
receiver’s display.
Note
The AV receiver supports four types of RDS
information:
PS (Program Service)
When tuned to an RDS station that’s broadcasting PS
information, the station’s name will be displayed.
Pressing DISPLAY will display the frequency for 3
seconds.
RT (Radio Text)
When tuned to an RDS station that’s broadcasting
text information, the text will be shown on the AV
receiver’s display.
PTY (Program Type)
This allows you to search for RDS radio stations by
type.
TP (Traffic Program)
This allows you to search for RDS radio stations that
broadcast traffic information (➔ page 34).
En-33
• The message “Waiting” may appear while the AV
receiver waits for the RT information.
• If the message “No Text Data” appears, no RT
information is available.
■ Finding Stations by Type (PTY)
You can search for radio stations by type.
1
Press RT/PTY/TP twice.
The current program type appears on the AV
receiver’s display.
2
Use PRESET e/r to select the type of
program you want.
See the table shown later in this chapter.
3
To start the search, press ENTER.
The AV receiver searches until it finds a station of
the type you specified, at which point it stops
briefly before continuing with the search.
Playback
4
When a station you want to listen to is found,
press ENTER.
If no stations are found, the message “Not
Found” appears.
■ Listening to Traffic News (TP)
You can search for stations that broadcast traffic
news.
1
2
RDS program types (PTY)
Type
Display
None
None
News reports
News
Current affairs
Affairs
Information
Info
Sport
Sport
Education
Educate
Drama
Drama
Culture
Culture
Press RT/PTY/TP three times.
If the current radio station is broadcasting TP
(Traffic Program), “[TP]” will appear on the AV
receiver’s display. If “TP” without square brackets
appears, this means that the station is not
broadcasting TP.
Science and technology
Science
Varied
Varied
Pop music
Pop M
Rock music
Rock M
To locate a station that is broadcasting TP,
press ENTER.
The AV receiver searches until it finds a station
that’s broadcasting TP.
If no stations are found, the message “Not
Found” appears.
Middle of the road music
Easy M
Light classics
Light M
Serious classics
Classics
Other music
Other M
Weather
Weather
Finance
Finance
Children’s programmes
Children
Social affairs
Social
Religion
Religion
Phone in
Phone In
Travel
Travel
Leisure
Leisure
Jazz music
Jazz
Country music
Country
National music
Nation M
Oldies music
Oldies
Folk music
Folk M
Documentary
Document
Alarm test
TEST
Alarm
Alarm!
En-34
Playing Audio and Video from Separate
Sources
You can listen to the audio of one input source while
watching the video of another. This function takes
advantage of the fact that when an audio-only input
source (TV/CD, AM, FM) is selected, the video input
source remains unchanged. The following procedure
shows how to listen to a CD player’s audio source
connected to TV/CD IN while watching a Blu-ray
Disc/DVD player’s video source connected to
BD/DVD.
Tip
• To use an input selector as audio-exclusive, you must
assign all video inputs to “- - - - -” ( ➔ pages 45 to 46).
1
2
Press BD/DVD.
3
Start playback on your Blu-Ray Disc/DVD and
CD players.
You can now enjoy watching your Blu-ray
Disc/DVD with the sound of your CD player.
Press TV/CD.
The audio output changes to the CD source, but
the video of previously-selected BD/DVD is
retained.
Playback
Using the Listening Modes
(North American and Taiwanese models)
About Listening Modes
The AV receiver’s listening modes can transform your
listening room into a movie theater or concert hall,
with high fidelity and stunning surround sound.
Selecting Listening Modes
MOVIE/TV, MUSIC, GAME
Note
■ Listening Mode Buttons
(European, Australian and Asian models)
Press RECEIVER first.
PURE AUDIO
MUSIC
MOVIE/TV
PURE AUDIO button and indicator
(European, Australian and Asian models)
This button selects the Pure Audio listening mode.
When this mode is selected, the AV receiver’s display
and analog video circuitry are turned off. Only video
signals input through HDMI input can be output from
the HDMI output. The indicator lights when this mode
is selected. Pressing this button again will select the
previous listening mode.
GAME
STEREO
MOVIE/TV, MUSIC, GAME
MOVIE/TV button
This button selects the listening modes intended for
use with movies and TV.
MUSIC button
This button selects the listening modes intended for
use with music.
GAME button
This button selects the listening modes intended for
use with video games.
STEREO button
This button selects the Stereo listening mode and All
Channel Stereo listening mode.
En-35
• The Dolby Digital and DTS listening modes can only be
selected if your Blu-ray Disc/DVD player is connected to the
AV receiver with a digital audio connection (coaxial, optical,
or HDMI).
• The listening modes you can select depends on the format
of the input signal. To check the format, see “Displaying
Source Information” (➔ page 39).
• While a pair of headphones is connected, you can select
the following listening modes: Pure Audio (European,
Australian and Asian models), Mono, Direct, and Stereo.
Playback
Input Source
The following audio formats are supported by the listening modes.
A
This is mono (monophonic) sound.
S
This is stereo (stereophonic) sound. Two independent audio signal channels
are reproduced through two speakers.
D
This is 5.1-channel surround sound. This surround system has five main
channels of sound and a sixth subwoofer channel (called the point-one
channel).
F*1 This is 7.1-channel surround sound. This is a further sound enhancement to
5.1-channel sound with two additional speakers that provide greater sound
envelopment and more accurate positioning of sounds.
*1
The AV receiver outputs this source in 5.1-channel surround sound.
■ Onkyo-Original DSP Listening Modes
Listening Mode
Description
Input
Source
Speaker
Layout
Orchestra
Suitable for classical or operatic music,
this mode emphasizes the surround
channels in order to widen the stereo
image, and simulates the natural
reverberation of a large hall.
A
S
D
F
C
Or ches t r a
Unplugged
Un p l u g g e d
Studio-Mix
S t u d i o –M i x
Speaker Layout
The illustration shows which speakers are activated in each channel. See
“4. Sp Config (Speaker Configuration)” for the speaker setup (➔ page 46).
Z
X
C
TV Logic
TV
Log i c
Game-RPG
G ame – RPG
Game-Action
G ame – A c t i o n
Game-Rock
G ame – R o c k
Game-Sports
G ame – S p o r t s
All Ch Stereo
A l l
Ch
S t e r eo
Full Mono
Fu l l
En-36
Mo n o
Suitable for acoustic instruments, vocals
and jazz, this mode emphasizes the
front stereo image, giving the impression
of being right in front of the stage.
Suitable for rock or pop music, listening
to music in this mode creates a lively
sound field with a powerful acoustic
image, like being at a club or rock
concert.
This mode adds realistic acoustics to TV
shows produced in a TV studio,
surround effects to the entire sound, and
clarity to voices.
In this mode, the sound has a dramatic
feel with a similar atmosphere to
Orchestra mode.
In this mode, sound localization is
distinct with emphasis on bass.
In this mode, sound pressure is
emphasized to heighten live feel.
Suitable for audio source with much
reverberation.
Ideal for background music, this mode
fills the entire listening area with stereo
sound from the front, and surround.
In this mode, all speakers output the
same sound in mono, so the sound you
hear is the same regardless of where
you are within the listening room.
XC
Playback
Listening Mode
Description
Input
Source
Speaker
Layout
Listening Mode
Description
T-D (TheaterDimensional)
With this mode you can enjoy a virtual
surround sound even with only two or
three speakers. This works by
controlling how sounds reach the
listener’s left and right ears. Good
results may not be possible if there’s too
much reverb, so we recommend that
you use this mode in an environment
with little or no natural reverb.
A
S
D
F
ZXC
DSD*3
In this mode, audio from the input source D
is output without surround-sound
processing. The speaker configuration
(presence of speakers), crossover
frequency, speaker distance, A/V Sync
and much of the processing set via the
D
audio setup are enabled. See “Onscreen Setup” for more details
F
(➔ page 41).
T–D
DSD
Dolby Digital
Do l b y
Do l b y
Do l b y
Listening Mode
Description
Input
Source
Speaker
Layout
DTS
Pure Audio*1*2
In this mode, the display and video
circuitry are turned off, minimizing
possible noise sources for the ultimate in
high-fidelity audio reproduction. (As the
analog video circuitry is turned off, only
video signals input through HDMI IN can
be output from the HDMI output.)
A
S
D
F
ZXC
DTS
Direct
D i r ec t
Stereo
S t e r eo
Mono
Mo n o
Multichannel
Mu l t i c h
+
D T S – HD
Speaker
Layout
XC
XC
T r u e HD
DTS-HD High
Resolution Audio
D
XC
D
F
XC
D
XC
D
XC
HR
DTS-HD Master
Audio
In this mode, audio from the input source
is output without surround-sound
processing. The speaker configuration
(presence of speakers) and speaker
distance settings are enabled, but much
of the processing set via the audio setup
is disabled. See “On-screen Setup” for
more details (➔ page 41).
D T S – HD MS T R
DTS Express
DTS
Exp r ess
DTS 96/24*5
DTS
Sound is output from the front left and
right speakers and subwoofer.
Use this mode when watching an old
movie with a mono soundtrack, or use it
with the foreign language soundtracks
recorded in the left and right channels of
some movies. It can also be used with
DVDs or other sources containing
multiplexed audio, such as karaoke
DVDs.
This mode is for use with PCM
multichannel sources.
D
Dolby TrueHD
■ Listening Modes
Pu r eAAu d i o
D
Dolby Digital Plus*4
Input
Source
D
F
XC
En-37
96 / 24
This mode is for use with DTS 96/24
sources. This is high-resolution DTS
with a 96 kHz sampling rate and 24-bit
resolution, providing superior fidelity.
Use it with DVDs that bear the DTS
96/24 logo.
Playback
Listening Mode
Dolby Pro Logic II
PL
Mo v i e
PL
Mu s i c
PL
Game
DTS Neo:6
Ne o : 6
C i n ema
Ne o : 6
Mu s i c
Description
Input
Source
Speaker
Layout
Dolby Pro Logic II expands any 2channel source for 5.1-channel
playback. It provides a very natural and
seamless surround-sound experience
that fully envelops the listener. As well
as music and movies, video games can
also benefit from the dramatic spatial
effects and vivid imaging.
Note
*1
*2
*3
*4
*5
• Dolby PLII Movie
S
Use this mode with DVDs and videos
that bear the Dolby Surround logo or
TV shows that feature Dolby Surround.
You can also use this mode with stereo
movies or TV shows and the AV
receiver will create a 5.1 surround mix
from the 2-channel stereo.
• Dolby PLII Music
Use this mode to add 5.1 surround to
stereo sources such as music CDs and
DVDs.
• Dolby PLII Game
Use this mode when playing game
discs.
XC
The listening mode may not be selected depending on the input signal. The
signal input from the external AV components can be displayed by the function
on the next page.
This mode expands any 2-channel
source for up to 5.1-channel playback. It
uses seven full-bandwidth channels of
matrix decoding for matrix-encoded
material, providing a very natural and
seamless surround sound experience
that fully envelops the listener.
• DTS Neo:6 Cinema
Use this mode with any stereo movie
(e.g., TV, DVD, VHS).
• DTS Neo:6 Music
Use this mode with any stereo music
source (e.g., CD, radio, cassette, TV,
VHS, DVD).
S
(North American and Taiwanese models) This listening mode is not available.
Pure Audio cannot be selected when Zone 2 is active.
Besides, if you activate Zone 2 while Pure Audio is selected, the listening mode will
automatically switch to Direct.
The AV receiver can input the DSD signal from HDMI IN. Depending on the player,
setting the output on the player side to PCM might bring better sound.
For the Blu-ray Discs, Dolby Digital is used.
DTS is used depending on the configuration of the AV receiver.
XC
En-38
Playback
Displaying Source Information
Using the Sleep Timer
You can display various information about the current
input source as follows.
With the sleep timer, you can set the AV receiver to
turn off automatically after a specified period.
1
1
Press RECEIVER once followed by DISPLAY
repeatedly to cycle through the available
information.
Tip
• Alternatively, you can use DISPLAY on the AV
receiver.
The following information can be typically displayed.
Press RECEIVER once followed by SLEEP
repeatedly to select the required sleep time.
The sleep time can be set from 90 to 10 minutes
in 10 minute steps.
The SLEEP indicator lights on the AV receiver’s
display when the sleep timer has been set. The
specified sleep time appears for about 5
seconds, then the previous display reappears.
Changing the Input Display
When you connect an u-capable Onkyo
component, you must configure the input display so
that u can work properly.
1
Tip
• See “Name” in “8. Source Setup” for changing the
name (➔ page 50).
Note
• “DOCK” and “TAPE” cannot be selected for the input
selector at the same time.
• Enter the appropriate remote control code before using
the remote controller for the first time (➔ page 58).
Tip
• If you need to cancel the sleep timer, press SLEEP
repeatedly until the SLEEP indicator goes off.
• To check the time remaining until the AV receiver
sleeps, press SLEEP. Note that if you press again on
SLEEP as the time being displayed is 10 minutes or
less, the sleep timer will go off.
Input source
& volume*1
Listening
mode
Setting the Display Brightness
You can adjust the brightness of the AV receiver’s
display.
Signal
format*2
Sampling
frequency*2
1
Press RECEIVER once followed by DIMMER
repeatedly to switch between: normal, dim, or
dimmer brightness.
Tip
• (North American and Taiwanese models)
Alternatively, you can use DIMMER on the AV
receiver.
*1
*2
When AM or FM radio is used, the band, preset number,
and frequency are displayed.
If the input signal is digital, the signal format is displayed.
Information is displayed for about three seconds, then
the previously displayed information reappears.
En-39
Change the name of the input selector to
“DOCK” or “TAPE”.
Muting the AV Receiver
You can temporarily mute the output of the AV
receiver.
1
Press RECEIVER followed by MUTING.
The output is muted and the MUTING indicator
flashes on the AV receiver’s display.
Tip
• To unmute, press MUTING again or adjust the volume.
• Muting is automatically cancelled when the AV
receiver is set to standby.
Playback
Using the Home Menu
The Home menu provides quick access to frequently
used menus.
Tip
• The on-screen menus appear only on a TV that is
connected to the HDMI OUT.
1
Press RECEIVER followed by HOME.
The Home menu will be superimposed on the TV
screen.
Tip
• Alternatively, you can use HOME on the AV receiver.
IN 1/2/3/4/5). Even with multiple components
connected through HDMI, you can easily switch
between inputs as their previews are displayed on
a single screen.
Press ENTER to display the main preview
(currently selected HDMI input) and the
additional previews (other HDMI inputs). Using
q/w or e/r to select a preview thumbnail and
pressing ENTER will switch the AV receiver to
that input source.
Tip
• If no video signals are present, the thumbnails will be
filled in black.
• You can specify the number of preview thumbnails as
well as their positioning on screen (➔ page 54).
Note
Home
Setup
InstaPrevue
F/W Update
Network Service
USB
2
Use q/w and ENTER to make the desired
selection.
Press HOME to close the menu.
■ Setup
` With this selection, you can access the common
settings of the on-screen Setup menu.
Press ENTER to display the Setup menu
(➔ page 44).
Tip
• You can also access frequently used settings from Quick
Setup (➔ page 41).
■ InstaPrevue
` With this selection, you can preview audio/video
streams coming from HDMI inputs (HDMI
• This function cannot be selected when:
– HDMI IN 6 is the current HDMI input source, or
– No signal is present on the current input source.
• Depending on video signals, the picture may not be
properly rendered on the preview thumbnails of
InstaPrevue.
■ F/W Update
` With this selection, you can update the firmware
of the AV receiver. Note that this selection will be
grayed out for a short while after the AV receiver
is turned on. Please wait until it becomes
operable.
Press ENTER to start the procedure
(➔ page 68).
■ Network Service
You need to connect the AV receiver to your home
network (➔ page 15).
` With this selection, you can use various Internet
radio services or play the contents stored in media
connected to your home network (➔ page 27 to
30). Note that this selection will be grayed out for
En-40
a short while after the AV receiver is turned on.
Please wait until it becomes operable.
Press ENTER to display the “NET” screen. If you
want to use the Internet radio services, use q/w
to select the desired service. Pressing ENTER
again switches to that selection. If you want to
play music files on a computer or media server,
use q/w to select “DLNA” and then press
ENTER. If you want to play music files on a
computer or NAS (Network Attached Storage),
use q/w to select “Home Media” and then press
ENTER.
■ USB
`With this selection, you can play contents of
portable players (iPod, etc.) and USB storage
devices connected to the AV receiver’s USB port
(➔ pages 26, 27). Note that this selection will be
grayed out for a short while after the AV receiver
is turned on. Please wait until it becomes
operable.
First, press USB repeatedly to select the
“USB(Front)” or “USB(Rear)” input.
Then, press ENTER to select a drive or browse
the contents of the media connected, followed
by q/w to select the desired folder or track.
Pressing ENTER as a track is selected will start
playback.
Note
• Only the front-panel USB input is compatible with
iPod/iPhone.
Advanced Operations
■ Audio (➔ page 42)
`You can change the following settings: “Bass”,
“Treble”, “PM Bass”, “Subwoofer Level”,
“Center Level”, “Audyssey”, “Dynamic EQ”,
“Dynamic Volume”, “Late Night”, “Music
Optimizer”, and “Cinema Filter”.
Using the Quick Setup
Advanced Operations
RECEIVER
■ Information*1
`You can view the information of the following
items: “Input” and “Output”.
ENTER,
q/w/e/r
RETURN
Q SETUP
On-screen Setup
This section describes the procedure for using the
remote controller unless otherwise specified.
1
With the AV receiver connected to a TV, there are two
ways of changing the settings on-screen: using the
Quick Setup or the Setup Menu (HOME).
Tip
• The on-screen menus appear only on a TV that is
connected to the HDMI OUT.
Note
• The on-screen menus are displayed when:
– There is no video input, or
– The video input is 480p, 576p, 720p, 1080i, or 1080p.
Note
*1
■ Quick Setup
The Quick Setup provides quick access to frequently
used settings. You can change settings and view the
current information.
■ Setup menu (HOME)
The Setup menu (HOME) provides a convenient way
to change the AV receiver’s various settings. Settings
are organized into 11 categories.
Press RECEIVER followed by Q SETUP.
The Quick Setup will be superimposed on the TV
screen.
■ Listening Mode*2
`You can select the listening modes that are
grouped in the following categories: “MOVIE/TV”,
“MUSIC”, “GAME”.
Use q/w to select the category and e/r to
select the listening mode. Press ENTER to
switch to the selected listening mode.
*2
Quick Setup
Input
Audio
Information
Listening Mode
Depending on the input source and listening mode, not
all channels shown here output the sound.
• This setting is not available in either of the following
cases:
–The “Audio TV Out” setting is set to “On” (➔ page 53).
–“HDMI CEC (RIHD)” is set to “On” (➔ page 52) and
you’re listening through your TV speakers.
[ENTER:Select]
Explanatory Notes
2
Use q/w and ENTER to make the desired
selection.
Press Q SETUP to close the menu.
Press RETURN to return to the previous menu.
■ Input
` You can select input sources and view information
on their assignments.
Use q/w to select an input source and view its
assignment information.
Pressing ENTER switches to the selected input
source.
En-41
a
b
■ PM Bass
` Off
` On
a Setting target
b Setting options (default setting underlined)
Advanced Operations
Using the Audio Settings of Quick
Setup
You can change various audio settings from the
Quick Setup (➔ page 41).
Note
• These settings are not available in either of the following
cases:
– The “Audio TV Out” setting is set to “On” (➔ page 53).
– “HDMI CEC (RIHD)” is set to “On” (➔ page 52) and
you’re listening through your TV speakers.
Tone Control
■ Bass
` –10 dB to 0 dB to +10 dB in 2 dB steps
You can boost or cut low-frequency sounds
output from the front speakers.
■ Treble
` –10 dB to 0 dB to +10 dB in 2 dB steps
You can boost or cut high-frequency sounds
output from the front speakers.
You can adjust the bass and treble for the front
speakers, except when Direct or Pure Audio
(European, Australian and Asian models) listening
mode is selected.
Operating on the AV receiver
1
Press TONE repeatedly to select either “Bass”
or “Treble”.
2
Use – and + to adjust.
Phase Matching Bass
■ PM Bass
` Off
` On
From the warm low notes produced by a cello to the
deep frequencies of electronic music, a good audio
system should be able to deliver plenty of bass
resonance.
While traditional enhancement systems effectively
boost low-frequency sound, they are often prone to
the effects of phase shifting, which can overwhelm
mid-range frequencies and muddy the sound. Our
Phase-Matching Bass Boost technology effectively
preserves mid-range clarity-allowing vocals and
strings to shine-while maintaining a smooth, powerful
bass response at all volume levels.
Note
• The Phase Matching Bass is disabled when the Direct or
Pure Audio (European, Australian and Asian models)
listening mode is selected.
• If the “Subwoofer” setting is set to “No”, this setting is fixed
to “Off”.
These temporary adjustments are cancelled when the
AV receiver is set to standby. To save the setting you
made here, go to “6. Level Cal (Level Calibration)”
(➔ page 48) before setting the AV receiver to
standby.
Note
• You cannot use these function while the AV receiver is
muted.
• These settings cannot be used while a pair of headphones
is connected.
• Speakers that are set to “No” or “None” in “4. Sp Config
(Speaker Configuration)” (➔ page 46) cannot be adjusted.
Audyssey®
■ Audyssey
See “Audyssey” in “8. Source Setup” (➔ page 49).
■ Dynamic EQ
See “Dynamic EQ” in “8. Source Setup” (➔ page 49).
■ Dynamic Volume
See “Dynamic Volume” in “8. Source Setup”
(➔ page 50).
Note
Operating on the AV receiver
1
2
Press TONE repeatedly to select “PM Bass”.
Use – and + to change the setting.
Speaker Levels
• These technologies can be used when all the following
conditions are met:
– Room Correction and Speaker Setup is completed. Note
that “Audyssey” requires the “Audyssey MultEQ Full
Calibration” method.
– Any listening mode other than Direct or Pure Audio
(European, Australian and Asian models) is selected.
– A pair of headphones is not connected.
• The setting is stored individually for each input selector.
■ Subwoofer Level
` –15 dB to 0 dB to +12 dB in 1 dB steps
■ Center Level
` –12 dB to 0 dB to +12 dB in 1 dB steps
You can adjust the volume of each speaker while
listening to an input source.
En-42
Operating
procedure
(➔ page 41)
Advanced Operations
Late Night
Music Optimizer
CinemaFILTER
■ Late Night
For Dolby Digital and Dolby Digital Plus sources,
the options are:
` Off
` Low:
Small reduction in dynamic range.
` High:
Large reduction in dynamic range.
■ Music Optimizer
` Off
` On
The Music Optimizer function enhances the sound
quality of compressed music files. When set to “On”,
the M.Opt indicator lights on the AV receiver’s
display, and the MUSIC OPTIMIZER indicator (North
American and Taiwanese models) lights on the
front panel.
■ Cinema Filter
`Off
`On
Turn this setting on to soften overly bright movie
soundtracks, which are typically mixed for
reproduction in a movie theater.
CinemaFILTER can be used with the following
listening modes: Dolby Digital, Dolby Digital Plus,
Dolby TrueHD, Dolby Pro Logic II Movie,
Multichannel, DTS, DTS Neo:6 Cinema, DTS 96/24,
DTS-HD High Resolution Audio, DTS-HD Master
Audio and DTS Express.
For Dolby TrueHD sources, the options are:
` Auto:
The Late Night function is set to “On” or “Off”
automatically.
` Off
` On
Turn this setting on to reduce the dynamic range of
Dolby Digital material so that you can still hear quiet
parts even when listening at low volume levels—ideal
for watching movies late at night when you don’t want
to disturb anyone.
Note
• The effect of the Late Night function depends on the
material that you are playing and the intention of the original
sound designer, and with some material there will be little
or no effect when you select the different options.
• The Late Night function can be used only when the input
source is Dolby Digital, Dolby Digital Plus, or Dolby
TrueHD.
• The Late Night function is set to “Off” when the AV receiver
is set to standby. For Dolby TrueHD sources, it will be set
to “Auto”.
Tip
• (North American and Taiwanese models) Alternatively,
you can use MUSIC OPTIMIZER on the AV receiver.
Note
Note
• The Music Optimizer function only works with PCM digital
audio input signals with a sampling rate below 48 kHz and
analog audio input signals.
When NET or USB input selector is selected, this function
even works with digital audio input signals with a sampling
rate below 48 kHz (except DSD signals and Dolby TrueHD
signals) regardless of the PCM digital audio input signals
with a sampling rate below 48 kHz.
• The Music Optimizer is disabled when the Direct or Pure
Audio (European, Australian and Asian models)
listening mode is selected.
• The setting is stored individually for each input selector.
En-43
• The CinemaFILTER may not work when used with certain
input sources.
Operating
procedure
(➔ page 41)
Advanced Operations
Using the Setup Menu (HOME)
Remote
indicator
Setup Menu Items
Setting target
6. Level Cal
(➔ page 48)
Left
Setting target
1. HDMI Input
(➔ page 45)
BD/DVD
Right
CBL/SAT
Surround Right
GAME
Surround Left
Subwoofer
PC
AUX
TV/CD
2. Component
(➔ page 46)
ENTER,
q/w/e/r
RETURN
7. Audio Adjust Input Ch (Mux)
(➔ page 48)
Input Ch (Mono)
BD/DVD
Panorama
CBL/SAT
Dimension
GAME
Center Width
PC
Center Image
Listening Angle
AUX
HOME
TV/CD
Press RECEIVER followed by HOME.
Center
Menu item
RECEIVER
1
2
Menu item
3. Digital Audio BD/DVD
(➔ page 46)
CBL/SAT
8. Source Setup Audyssey
(➔ page 49)
Dynamic EQ [Reference Level]
Dynamic Volume
Use q/w to select “Setup”, and then press
ENTER.
GAME
A/V Sync
PC
Name
3
Use q/w to select a menu item, and then press
ENTER.
AUX
4
Use q/w to select a setting target, and use e/r
to change the setting.
Press HOME to close the menu.
Press RETURN to return to the previous menu.
Audio Selector [Fixed Mode]
TV/CD
4. Sp Config
(➔ page 46)
Subwoofer
Front
Center
Surround
Crossover
Note
• This procedure can also be performed on the AV receiver
by using HOME, the cursor buttons, and ENTER.
• During Audyssey MultEQ® Room Correction and Speaker
Setup, messages, etc., that are displayed on the TV screen
will appear on the AV receiver’s display.
Double Bass
5. Sp Distance
(➔ page 47)
9. Hardware
(➔ page 51)
Volume OSD
Remote ID
(North American and Taiwanese
models)
AM/FM Freq Step
(European, Australian and Asian
models)
AM Freq Step
Auto Standby [HDMI Through]
Unit
Left
Center
10. HDMI Setup HDMI CEC (RIHD)
(➔ page 52)
HDMI Through
Right
Audio TV Out
Surround Right
Audio Return Ch
Surround Left
LipSync
Subwoofer
InstaPrevue [Sub Window, Position]
En-44
Advanced Operations
Menu item
Setting target
11. Network
Setup
(➔ page 54)
MAC Address
1. HDMI Input
DHCP [IP Address, Subnet Mask,
Gateway, DNS Server]
Proxy URL [Proxy Port]
Network Standby
Update Notice
Explanatory Notes
a
b
c
4. Sp Config (Speaker Configuration)
■ Subwoofer
`Yes
`No
a Menu selection
b Setting target
c Setting options (default setting underlined)
Setup
1. HDMI Input
2. Component
3. Digital Audio
4. Sp Config
5. Sp Distance
6. Level Cal
7. Audio Adjust
8. Source Setup
9. Hardware
10. HDMI Setup
11. Network Setup
Menu
BD/DVD
CBL/SAT
GAME
PC
AUX
TV/CD
Setting target
If you connect a video component to an HDMI input,
you must assign that input to an input selector. For
example, if you connect your Blu-ray Disc/DVD player
to HDMI IN 2, you must assign “HDMI2” to the
“BD/DVD” input selector.
Here are the default assignments.
Input selector
Default assignment
BD/DVD
HDMI1
CBL/SAT
HDMI2
GAME
HDMI3
PC
HDMI4
AUX
-----
TV/CD
-----
• Do not assign an HDMI IN to the TV/CD selector while
“HDMI CEC (RIHD)” is set to “On” (➔ page 52), otherwise
appropriate CEC (Consumer Electronics Control) operation
will not be guaranteed.
• If you assign “- - - - -” to an input selector that is currently
selected in “HDMI Through” (➔ page 53), the “HDMI
Through” setting will be automatically switched to “Off”.
■ BD/DVD, CBL/SAT, GAME, PC, AUX, TV/CD
` HDMI1, HDMI2, HDMI3, HDMI4, HDMI5, HDMI6:
Select the input to which the component has
been connected.
` - - - - -:
Select if you’re not using the HDMI OUT.
Each HDMI input cannot be assigned to two input
selectors or more. When HDMI1 - HDMI6 have
already been assigned, you must first set any
unused input selectors to “- - - - -” or you will be
unable to assign HDMI1 - HDMI6 to other input
selectors.
Note
• If no video component is connected to the HDMI input (even
if the HDMI input is assigned), the AV receiver selects the
video source based on the setting of “2. Component
(Component Video Input)”.
• When an HDMI IN is assigned to an input selector as
explained here, the same HDMI IN will be set as a priority
in the “3. Digital Audio (Digital Audio Input)” (➔ page 46). In
this case, if you want to use the coaxial or optical audio
input, make the appropriate selection in the “Audio
Selector” setting (➔ page 51).
En-45
Operating
procedure
(➔ page 44)
Advanced Operations
2. Component (Component Video
Input)
If you connect a video component to a component
video input, you must assign that input to an input
selector. For example, if you connect your Blu-ray
Disc/DVD player to COMPONENT VIDEO IN 2, you
must assign “IN2” to the “BD/DVD” input selector.
Here are the default assignments.
3. Digital Audio (Digital Audio Input)
If you connect a component to a digital audio input,
you must assign that input to an input selector. For
example, if you connect your CD player to the
COAXIAL IN 1, you must assign “COAXIAL1” to the
“TV/CD” input selector.
Here are the default assignments.
Input selector
Default assignment
COAXIAL1
Input selector
Default assignment
BD/DVD
BD/DVD
IN1
CBL/SAT
COAXIAL2
CBL/SAT
IN2
GAME
-----
GAME
-----
PC
-----
PC
-----
AUX
-----
AUX
-----
TV/CD
OPTICAL
TV/CD
-----
■ BD/DVD, CBL/SAT, GAME, PC, AUX, TV/CD
` COAXIAL1, COAXIAL2, OPTICAL:
Select the input to which the component has
been connected.
` - - - - -:
Select if the component is connected to an
analog audio input.
■ BD/DVD, CBL/SAT, GAME, PC, AUX, TV/CD
` IN1, IN2:
Select the input to which the component has
been connected.
` - - - - -:
Select if you’re not using the COMPONENT
VIDEO OUT.
Note
• When an HDMI IN is assigned to an input selector in
“HDMI Input” (➔ page 45), the same HDMI IN will be set
as a priority in this assignment. In this case, if you want to
use the coaxial or optical audio input, make the appropriate
selection in the “Audio Selector” (➔ page 51).
• Supported sampling rates for PCM signals (stereo/mono)
from a digital input (optical and coaxial) are
32/44.1/48/88.2/96 kHz/16, 20, 24 bit.
4. Sp Config (Speaker Configuration)
Some of the settings in this section are set
automatically by Audyssey MultEQ® Room
Correction and Speaker Setup function
(➔ page 21).
Here you can check the settings made by
Audyssey MultEQ Room Correction and Speaker
Setup function, or set them manually, which is useful
if you change one of the connected speakers after
using Audyssey MultEQ Room Correction and
Speaker Setup function.
This section explains how to specify which speakers
are connected and their sizes.
Cone diameter
For speakers with a cone diameter larger than 6-1/2
inches (16 cm), specify Large (full band). For those
with a smaller diameter, specify Small (default
crossover 100Hz).
The crossover frequency can be changed in
“Crossover (Crossover Frequency)” (➔ page 47).
Note
• These settings are not available in either of the following
cases:
– A pair of headphones is connected.
– The “Audio TV Out” setting is set to “On” (➔ page 53).
– “HDMI CEC (RIHD)” is set to “On” (➔ page 52) and
you’re listening through your TV speakers.
■ Subwoofer
`Yes
`No
En-46
Operating
procedure
(➔ page 44)
Advanced Operations
■ Front
` Small:
` Large:
Select based on the cone diameter.
Note
• If the “Subwoofer” setting is set to “No”, this setting is fixed
to “Large”.
■ Center*1, Surround*1
` Small:
` Large:
Select based on the cone diameter.
` None
Note
*1
If the “Front” setting is set to “Small”, the “Large” option
cannot be selected.
■ Crossover (Crossover Frequency)
This setting is advantageous for the speakers that
you specified as “Small” in “4. Sp Config (Speaker
Configuration)” (➔ page 46). To get the best bass
performance from your speaker system, you need
to set the crossover frequency according to the size
and frequency response of your speakers.
` 40Hz, 50Hz, 60Hz, 70Hz, 80Hz, 90Hz, 100Hz,
120Hz, 150Hz, 200Hz
Use the diameter of the smallest speaker in your
system when choosing the crossover frequency.
Speaker cone diameter
Crossover frequency
Over 8 in. (20 cm)
40/50/60 Hz*
6-1/2 to 8 in. (16 to 20 cm)
70/80/90 Hz*
5-1/4 to 6-1/2 in. (13 to 16 cm)
100 Hz
3-1/2 to 5-1/4 in. (9 to 13 cm)
120 Hz
Under 3-1/2 in. (9 cm)
150/200 Hz*
*
5. Sp Distance (Speaker Distance)
Note
• For a more accurate setting, look up the frequency
response in the manuals supplied with your speakers and
set accordingly.
• Choose a higher crossover frequency if you want more
sound from your subwoofer.
■ Double Bass
This setting is NOT set automatically by
Audyssey MultEQ® Room Correction and Speaker
Setup function (➔ page 21).
` On
` Off
Turn this setting on to boost bass output by feeding
bass sounds from the front left, right, and center
channels to the subwoofer.
Note
• When the “Subwoofer” setting is set to “No” or the “Front”
setting to “Small”, this setting is fixed to “Off” (➔ page 46).
• This setting is set to “On” automatically when the
“Subwoofer” and “Front” settings are set for the first time
to “Yes” and “Large” respectively.
This setting is set automatically by
Audyssey MultEQ Room Correction and Speaker
Setup function (➔ page 21).
Here you can specify the distance from each speaker
to the listening position so that the sound from each
speaker arrives at the listener’s ears as the sound
designer intended.
Note
• These settings are not available in either of the following
cases:
– A pair of headphones is connected.
– The “Audio TV Out” setting is set to “On” (➔ page 53).
– “HDMI CEC (RIHD)” is set to “On” (➔ page 52) and
you’re listening through your TV speakers.
■ Unit
`feet:
Distances can be set in feet. Range: 1ft to 30ft
in 1 foot steps.
`meters:
Distances can be set in meters. Range: 0.3m to
9.0m in 0.3 meter steps.
(The default setting varies from country to country.)
■ Left, Center, Right, Surround Right, Surround
Left, Subwoofer
`Specify the distance from each speaker to your
listening position.
Note
• Speakers that you set to “No” or “None” in the “4. Sp Config
(Speaker Configuration)” (➔ page 46) cannot be selected.
Choose the setting matching your speaker.
En-47
Operating
procedure
(➔ page 44)
Advanced Operations
6. Level Cal (Level Calibration)
This setting is set automatically by
Audyssey MultEQ® Room Correction and Speaker
Setup function (➔ page 21).
Here you can adjust the level of each speaker with
the built-in test tone so that the volume of each
speaker is the same at the listening position.
Note
• These settings cannot be calibrated in either of the
following cases:
– A pair of headphones is connected.
– The “Audio TV Out” setting is set to “On” (➔ page 53).
– “HDMI CEC (RIHD)” is set to “On” (➔ page 52) and
you’re listening through your TV speakers.
– The AV receiver is muted.
■ Left, Center*1, Right, Surround Right, Surround
Left
` –12 dB to 0 dB to +12 dB in 1 dB steps.
■ Subwoofer*1
` –15 dB to 0 dB to +12 dB in 1 dB steps.
Note
• Speakers that you set to “No” or “None” in “4. Sp Config
(Speaker Configuration)” (➔ page 46) cannot be selected.
*1 For the center speaker and subwoofer, the level settings
made by using the Quick Setup are saved in this menu
(➔ page 42).
Dolby
7. Audio Adjust
With the Audio Adjust functions and settings, you can
adjust the sound and listening modes as you like.
Multiplex/Mono
■ Multiplex
Input Ch (Mux)
` Main
` Sub
` Main/Sub
This setting determines which channel of a stereo
multiplex source is output. Use it to select audio
channels or languages with multiplex sources,
multilingual TV broadcasts, and so on.
■ Mono
Input Ch (Mono)
` Left+Right
` Left
` Right
This setting specifies the channel to be used for
playing any 2-channel digital source such as Dolby
Digital, or 2-channel analog/PCM source in the Mono
listening mode.
Tip
• If you’re using a handheld sound level meter, adjust the
level of each speaker so that it reads 75 dB SPL at the
listening position, measured with C-weighting and slow
reading.
En-48
■ PL II Music (2ch Input)
These settings apply to only 2-channel stereo
sources.
Panorama
`On
`Off
With this setting, you can broaden the width of the
front stereo image when using the Dolby Pro Logic II
Music listening mode.
Dimension
`–3 to 0 to +3
With this setting, you can move the sound field
forward or backward when using the Dolby Pro Logic
II Music listening mode. Higher settings move the
sound field backward. Lower settings move it forward.
If the stereo image feels too wide, or there’s too much
surround sound, move the sound field forward to
improve the balance. Conversely, if the stereo image
feels like it’s in mono, or there’s not enough surround
sound, move it backward.
Center Width
`0 to 3 to 7
With this setting, you can adjust the width of the
sound from the center speaker when using the Dolby
Pro Logic II Music listening mode. Normally, if you’re
using a center speaker, the center channel sound is
output from only the center speaker. (If you’re not
using a center speaker, the center channel sound will
be distributed to the front left and right speakers to
create a phantom center.) This setting controls the
front left, right, and center mix, allowing you to adjust
the weight of the center channel sound.
Operating
procedure
(➔ page 44)
Advanced Operations
DTS
8. Source Setup
■ Neo:6 Music
Center Image
` 0 to 2 to 5
With this setting, you can specify by how much the
front left and right channel output is attenuated in
order to create the center channel.
Changing the value from “0” to “5” will spread the
sound of the center channel to left and right
(outwards).
Theater-Dimensional
■ Listening Angle
` Wide:
Select if the listening angle is greater than 30
degrees.
` Narrow:
Select if the listening angle is less than 30
degrees.
With this setting, you can optimize the TheaterDimensional listening mode by specifying the angle of
the front left and right speakers relative to the
listening position. Ideally, the front left and right
speakers should be equidistant from the listening
position and at an angle close to one of the two
available settings.
Front left speaker
Items can be set individually for each input selector.
Press the input selector buttons to select an input
source.
Audyssey®
The tone for each speaker is set automatically by
Audyssey MultEQ® Room Correction and Speaker
Setup. To enable the following settings, you must first
perform the Room Correction and Speaker Setup
(➔ page 21).
• These technologies cannot be used when a pair of
headphones is connected.
■ Audyssey
` Off
` Movie:
Select this setting for movie material.
The Audyssey indicator will light.
` Music:
Select this setting for music material.
The Audyssey indicator will light.
Note
• When “Audyssey Quick Start” has been used for
measurement, “Audyssey” cannot be selected.
• Audyssey equalizing does not work with DSD sources.
Front right speaker
Listening angle: 30°
Note
• For best results, we recommend setting “Narrow” to 20°
and “Wide” to 40°.
En-49
■ Dynamic EQ
`Off
`On:
Audyssey Dynamic EQ® becomes active.
The Dynamic EQ indicator will light.
With Audyssey Dynamic EQ, you can enjoy great
sound even when listening at low volume levels.
Audyssey Dynamic EQ solves the problem of
deteriorating sound quality as volume is decreased by
taking into account human perception and room
acoustics. It does so by selecting the correct
frequency response and surround volume levels
moment-by-moment so that the content sounds the
way it was created at any volume level — not just at
reference level.
■ Reference Level
Audyssey Dynamic EQ Reference Level Offset
`0 dB:
This should be selected for movie contents.
`5 dB :
Select this setting for content that has a very
wide dynamic range, such as classical music.
`10 dB:
Select this setting for jazz or other music that
has a wider dynamic range. This setting should
also be selected for TV content as that is usually
mixed at 10 dB below film reference.
`15 dB:
Select this setting for pop/rock music or other
program material that is mixed at very high
listening levels and has a compressed dynamic
range.
Movies are mixed in rooms calibrated for film
reference. To achieve the same reference level in a
home theater system each speaker level must be
adjusted so that –30 dBFS band-limited (500 Hz to
2000 Hz) pink noise produces 75 dB sound pressure
level at the listening position. A home theater system
automatically calibrated by Audyssey MultEQ will play
Operating
procedure
(➔ page 44)
Advanced Operations
at reference level when the master volume control is
set to the 64 position. At that level you can hear the
mix as the mixers heard it.
Audyssey Dynamic EQ® is referenced to the
standard film mix level. It makes adjustments to
maintain the reference response and surround
envelopment when the volume is turned down from
64. However, film reference level is not always used
in music or other non-film content.
Audyssey Dynamic EQ Reference Level Offset
provides three offsets from the film level reference
(5 dB, 10 dB, and 15 dB) that can be selected when
the mix level of the content is not within the standard.
Note
• If “Dynamic EQ” setting is set to “Off”, this technology
cannot be used.
■ Dynamic Volume
` Off
` Light:
Activates Light Compression Mode.
` Medium:
Activates Medium Compression Mode.
` Heavy:
Activates Heavy Compression Mode. This
setting affects volume the most. It quiets the
loud parts, such as explosions, and boosts the
quiet parts so they can be heard.
Note
• If you make Dynamic Volume active, “Dynamic EQ” is set
to “On”. The Dynamic Vol indicator will light.
• When “Dynamic EQ” is set to “Off”, “Dynamic Volume” is
automatically switched to “Off”.
About Audyssey Dynamic EQ®
Audyssey Dynamic EQ solves the problem of
deteriorating sound quality as volume is decreased by
taking into account human perception and room
acoustics. Dynamic EQ selects the correct frequency
response and surround levels moment-by-moment at
any user-selected volume setting. The result is bass
response, tonal balance and surround impression
that remain constant despite changes in volume.
Dynamic EQ combines information from incoming
source levels with actual output sound levels in the
room, a prerequisite for delivering a loudness
correction solution. Audyssey Dynamic EQ works in
tandem with Audyssey MultEQ® to provide wellbalanced sound for every listener at any volume level.
About Audyssey Dynamic Volume®
Audyssey Dynamic Volume solves the problem of
large variations in volume level between television
programs, commercials, and between the soft and
loud passages of movies. Dynamic Volume looks at
the preferred volume setting by the user and then
monitors how the volume of program material is being
perceived by listeners in real time to decide whether
an adjustment is needed. Whenever necessary,
Dynamic Volume makes the necessary rapid or
gradual adjustments to maintain the desired playback
volume level while optimizing the dynamic range.
Audyssey Dynamic EQ is integrated into
Dynamic Volume so that as the playback volume is
adjusted automatically, the perceived bass response,
tonal balance, surround impression and dialog clarity
remain the same whether watching movies, flipping
between television channels or changing from stereo
to surround sound content.
A/V Sync
■ A/V Sync
`0 msec to 400 msec in 10 msec steps.
When using progressive scanning on your Blu-ray
Disc/DVD player, you may find that the picture and
sound are out of sync. With this setting, you can
correct this by delaying the audio signals.
Press ENTER to view the TV picture while setting the
delay when the video source is output to HDMI OUT.
To return to the previous screen, press RETURN.
The range of values you can adjust will depend on
whether your TV or display supports HDMI Lip Sync
and if the “LipSync” setting is set to “On” or not
(➔ page 53).
Note
• A/V Sync is disabled when the Pure Audio (European,
Australian and Asian models) or Direct listening mode is
used with an analog input source.
• This setting cannot be used with the NET and USB input
selectors.
Preset Name For Input Selector
■ Name
`- - -, Blu-ray, DVD, HD DVD, VCR, DVR, Tivo,
CableSTB, SAT STB, PS3, Wii, Xbox, PC, TV,
CD, TAPE, iPod, DOCK:
To reset to the default, select “- - -”.
You can enter a preset name for each individual input
selector for easy identification. When entered, the
preset name will be displayed.
Note
• You can’t assign the same preset name to multiple input
selectors.
• This setting cannot be used for the AM, FM, NET or USB
input selector.
En-50
Operating
procedure
(➔ page 44)
Advanced Operations
Audio Selector
■ Audio Selector
` ARC:
The audio signal from your TV tuner can be sent
to the HDMI OUT of the AV receiver.*1
With this selection, the TV’s audio can be
automatically selected as a priority among other
assignments.
` HDMI:
This can be selected when HDMI IN has been
assigned as an input source. If both HDMI
(HDMI IN) and digital audio inputs (COAXIAL IN
or OPTICAL IN) have been assigned, HDMI
input is automatically selected as a priority.
` COAXIAL:
This can be selected when COAXIAL IN has
been assigned as an input source. If both
coaxial and HDMI inputs have been assigned,
coaxial input is automatically selected as a
priority.
` OPTICAL:
This can be selected when OPTICAL IN has
been assigned as an input source. If both optical
and HDMI inputs have been assigned, optical
input is automatically selected as a priority.
` Analog:
The AV receiver always outputs analog signals.
You can set priorities of audio output when there are
both digital and analog inputs.
Note
• This setting can be made only for the input source that is
assigned as HDMI IN, COAXIAL IN, or OPTICAL IN.
• This setting cannot be used with the NET and USB input
selectors.
*1 You can select “ARC” if you select the TV/CD input
selector. But you cannot if you’ve selected “Off” in the
“Audio Return Ch” setting (➔ page 53).
Setting the Incoming Digital Signal (Fixed
Mode)
■ Fixed Mode
` Off:
The format is detected automatically. If no digital
input signal is present, the corresponding analog
input is used instead.
` PCM:
Only 2-channel PCM format input signals will be
heard. If the input signal is not PCM, the PCM
indicator will flash and noise may also be
produced.
` DTS:
Only DTS (but not DTS-HD) format input signals
will be heard. If the input signal is not DTS, the
dts indicator will flash and there will be no
sound.
When “HDMI”, “COAXIAL” or “OPTICAL” is selected
in the “Audio Selector” setting, you can then specify
the signal type in “Fixed Mode”.
Normally, the AV receiver detects the signal format
automatically. However, if you experience either of
the following issues when playing PCM or DTS
material, you can manually set the signal format to
PCM or DTS.
• If the beginnings of tracks from a PCM source are
cut off, try setting the format to PCM.
• If noise is produced when fast forwarding or
reversing a DTS CD, try setting the format to DTS.
Note
9. Hardware
OSD
■ Volume OSD
`On
`Off
Turn this setting on to display the volume level on the
TV screen while it is adjusted.
Remote ID
■ Remote ID
`1, 2, or 3
When several Onkyo components are used in the
same room, their remote ID codes may overlap. To
differentiate the AV receiver from other components,
you can change its remote ID from “1”, to “2” or “3”.
Note
• If you do change the AV receiver’s remote ID, be sure to
change the remote controller to the same ID (see below),
otherwise, you won’t be able to control it with the remote
controller.
Changing the remote controller’s ID
1
While holding down RECEIVER, press and
hold down Q SETUP until the remote indicator
lights (about 3 seconds).
2
Use the number buttons to enter ID 1, 2, or 3.
The remote indicator flashes twice.
• The setting will be reset to “Off” when you change the
setting in “Audio Selector”.
En-51
Operating
procedure
(➔ page 44)
Advanced Operations
Tuner
■ AM/FM Freq Step (North American and
Taiwanese models)
` 10 kHz/200 kHz:
` 9 kHz/50 kHz:
Select the frequency step according to your
area.
■ AM Freq Step (European, Australian and Asian
models)
` 10 kHz:
` 9 kHz:
Select the frequency step according to your
area.
For AM/FM tuning to work properly, you must specify
the AM/FM frequency step used in your area.
Note
• When this setting is changed, all radio presets will be deleted.
Auto Standby
■ Auto Standby
` Off
` On
When “Auto Standby” is set to “On”, the ASb
indicator lights and the AV receiver will automatically
enter standby mode if there is no operation for 30
minutes with no audio and no video signal input.
“Auto Standby” will appear on the AV receiver’s
display and OSD 30 seconds before the Auto
Standby comes on.
Default setting: On (European, Australian and
Asian models), Off (North American and
Taiwanese models)
■ HDMI Through
` Off
` On
This setting enables or disables the Auto Standby
during HDMI Through by detecting the audio/video
input signal.
When this setting is set to “On”, the AV receiver will
automatically enter standby mode if there is no audio
and no video signal input during HDMI Through for 30
minutes. (The Auto Standby function does not work
when Zone 2 is on.)
When this setting is set to “Off”, the status of HDMI
Through is continued regardless of audio/video input
signal.
Tip
• Entering standby mode is possible by setting “HDMI CEC
(RIHD)” to “On” and using CEC-compatible component
regardless of the above-mentioned setting.
See “HDMI CEC (RIHD)” in “10. HDMI Setup” for linked
operation.
• When the HDMI Through is enabled, the power
consumption slightly increases.
Note
• This setting is fixed to “Off” when “Auto Standby” is set to
“Off”.
Note
10. HDMI Setup
■ HDMI CEC (RIHD)
`Off
`On
Turn this setting on to allow p-compatible
components connected via HDMI to be controlled by
the AV receiver (➔ page 15).
Note
• When the setting is set to “On” and the menu is closed, the
names of connected p-compatible components and
“RIHD On” are displayed on the AV receiver.
“Search…” → “(name)” → “RIHD On”
When the AV receiver cannot receive the name of the
component, it is displayed as “Player*” or “Recorder*”, etc
(“*” shows up and indicates the number of components,
when two or more are received).
• When an p-compatible component is connected to
the AV receiver via an HDMI cable, the name of the
connected component is displayed on the AV receiver’s
display. For example, while you are watching TV
broadcasting, if you operate a Blu-ray Disc/DVD player
(being powered on) with the remote control of the AV
receiver, the name of the Blu-ray Disc/DVD player will be
displayed on the AV receiver.
• Set it to “Off” when a connected piece of equipment is not
compatible or it is unclear whether the equipment is
compatible or not.
• If operation is not normal when set to “On”, change the
setting to “Off”.
• Refer to the connected component’s instruction manual for
details.
• When the “HDMI CEC (RIHD)” setting is set to “On”, the
power consumption in standby mode slightly increases.
(Depending on the TV status, the AV receiver will enter
standby mode as usual.)
• When the source equipment is connected with the u
connection, it may malfunction if “HDMI CEC (RIHD)” is set
to “On”.
• Set to “On”, the Auto Standby function may activate itself
during playback with some sources.
• The Auto Standby function does not work when Zone 2 is on.
En-52
Operating
procedure
(➔ page 44)
Advanced Operations
■ HDMI Through
` Off
` BD/DVD, CBL/SAT, GAME, PC, AUX, TV/CD:
Selects the input source for which the HDMI
Through function is enabled.
` Last:
The HDMI Through function is activated on the
input source selected at the time of setting the
AV receiver to standby mode.
When enabling the HDMI Through function,
regardless of whether the AV receiver is on or in
standby, both audio and video streams from an HDMI
input will be output to the TV or other components via
HDMI connection. The HDMI indicator will be dimly-lit
in standby mode. Note that the indicator may not light
under certain conditions (➔ page 20).
This setting is fixed to “Auto” automatically when the
above “HDMI CEC (RIHD)” setting is set to “On”,
resulting in automatic input source selection.
Note
• Only an input source assigned to an HDMI IN via
“HDMI Input” setting is enabled (➔ page 45).
• The power consumption in standby mode will increase
during the HDMI Through function; however in the following
cases, the power consumption can be saved:
– The TV is in standby mode.
– You are watching a TV program.
• Refer to the connected component’s instruction manual for
details.
• Depending on the connected component, the correct input
source may not be selected with the setting fixed to “Auto”.
• This setting is set to “Off” automatically when the “HDMI
CEC (RIHD)” setting is set to “Off”.
■ Audio TV Out
` Off
` On
This preference determines whether the incoming
audio signal is output from the HDMI output. You may
want to turn this preference on if your TV is
connected to the HDMI output and you want to listen
to the audio from a connected component through
your TV’s speakers. Normally, this should be set to
“Off”.
Note
• If “On” is selected and the audio can be output from the TV,
the AV receiver will output no sound through its speakers.
In this case, “TV Speaker” appears on the AV receiver’s
display by pressing DISPLAY.
• When “HDMI CEC (RIHD)” is set to “On”, this setting is
fixed to “Auto”.
• With some TVs and input signals, no sound may be output
even when this setting is set to “On”.
• When “Audio TV Out” or “HDMI CEC (RIHD)” is set to “On”
and you’re listening through your TV’s speakers, turning up
the AV receiver’s volume control will make the sound be
output from the AV receiver’s front left and right speakers.
To stop the AV receiver’s speakers producing sound,
change the settings, change your TV’s settings, or turn
down the AV receiver’s volume.
• Listening mode cannot be changed when this setting is set
to “On” and the audio is output from the TV.
• This setting is set to “Off” automatically when the “HDMI
CEC (RIHD)” setting is set to “Off”.
■ Audio Return Ch
`Off
`Auto:
The audio signal from your TV tuner can be sent
to the HDMI OUT of the AV receiver.
The audio return channel (ARC) function allows an
ARC capable TV to send the audio stream to HDMI
OUT of the AV receiver. To use this function, you
must select the TV/CD input selector and your TV
must be ARC capable. The ARC indicator will light
when the audio signal is detected. Default setting:
“- - - - ”
Note
• This setting is fixed to “- - - -” when the “HDMI CEC (RIHD)”
setting is set to “Off”.
• This setting is set to “Auto” automatically when the “HDMI
CEC (RIHD)” setting is set to “On” for the first time.
• If you set “Audio Return Ch” to “Auto”, the “Audio
Selector” settings of the TV/CD input selector will be
automatically switched to “ARC” (➔ page 51).
Tip
• After changing the settings of the “HDMI CEC (RIHD)”,
“HDMI Through” or “Audio Return Ch”, turn off the power
on all connected pieces of equipment and then turn them on
again. Refer to the user’s manuals for all connected pieces
of equipment.
■ LipSync
`Off
`On
This function allows the AV receiver to automatically
correct any delay between the video and the audio,
based on the data from the connected monitor.
Note
• This function works only if your HDMI-compatible TV
supports HDMI Lip Sync.
En-53
Operating
procedure
(➔ page 44)
Advanced Operations
■ InstaPrevue
These settings apply to “InstaPrevue” of the Home
menu (➔ page 40) and specify the preview display of
HDMI video streams.
Sub Window
` Multi:
Displays preview thumbnails all at once.
` Single:
Displays preview thumbnails one-by-one.
With this setting, you can set the number of preview
thumbnails displayed.
Position
(with “Sub Window” set to “Multi”)
` Top, Bottom, Left, Right
(with “Sub Window” set to “Single”)
` UpperL, UpperR, LowerL, LowerR
With this setting, you can set the position of preview
thumbnails on the TV screen.
Note
• Depending on video signals, the picture may not be
properly rendered on the preview thumbnails of
InstaPrevue.
11. Network Setup
This section explains how to configure the AV
receiver’s network settings manually.
After modifying the network settings, you must
confirm the changes by executing “Save”.
If your router’s DHCP server is enabled, you don’t
need to change any of these settings, as the AV
receiver is set to use DHCP to configure itself
automatically by default (i.e., DHCP is set to
“Enable”). If, however, your router’s DHCP server is
disabled (you’re for example using static IP), you’ll
need to configure these settings yourself, in which
case, a knowledge of Ethernet networking is
essential.
What’s DHCP?
DHCP (Dynamic Host Configuration Protocol) is used
by routers, computers, the AV receiver, and other
devices to automatically configure themselves on a
network.
What’s DNS?
The DNS (Domain Name System) translates domain
names into IP addresses. For example, when you
enter a domain name such as www.onkyousa.com in
your Web browser, before accessing the site, your
browser uses DNS to translate this into an IP
address, in this case 63.148.251.142.
■ MAC Address
This is the AV receiver’s MAC (Media Access
Control) address. This address cannot be changed.
■ DHCP
`Enable
`Disable
This setting determines whether or not the AV
receiver uses DHCP to automatically configure its IP
Address, Subnet Mask, Gateway, and DNS Server
settings.
Note
• If you select “Disable”, you must configure the “IP
Address”, “Subnet Mask”, “Gateway”, and “DNS Server”
settings yourself.
■ IP Address
`Class A:
“10.0.0.0” to “10.255.255.255”
`Class B:
“172.16.0.0” to “172.31.255.255”
`Class C:
“192.168.0.0” to “192.168.255.255”
Enter a static IP address provided by your Internet
Service Provider (ISP).
Most routers use Class C IP addresses.
■ Subnet Mask
Enter the subnet mask address provided by your ISP
(typically 255.255.255.0).
■ Gateway
Enter the gateway address provided by your ISP.
■ DNS Server
Enter the DNS server address provided by your ISP.
■ Proxy URL
To use a Web proxy, enter its URL here.
■ Proxy Port
If you’re using a Web proxy, enter a proxy port
number here.
En-54
Operating
procedure
(➔ page 44)
Advanced Operations
■ Network Standby
` On
` Off
This setting enables or disables control over the
network.
When enabled, the NET indicator will be dimly-lit
while the AV receiver is in standby mode. Note that
the indicator may not light under certain conditions
(➔ page 20).
Note
• When set to “On”, the power consumption slightly
increases in standby mode.
■ Update Notice
` Enable
` Disable
When this setting is enabled, you will be notified if a
firmware update via network of high importance is
available.
Note
• Selecting “Never Remind me” on the notification window
will switch this setting to “Disable” (➔ page 20).
• For details on the update notification, see “Firmware
Update Notification” (➔ page 20).
En-55
Operating
procedure
(➔ page 44)
Advanced Operations
Zone 2
Controlling Zone 2 Components
In addition to the main listening room, you can also
enjoy playback in another room, or as we call Zone 2.
And, you can select a different source for each room.
■ Operating on the AV receiver
ZONE 2 OFF
Connecting the Zone Speakers to an
Additional Amplifier
1
Main room
TV
AV receiver
To turn on Zone 2 and select an input source,
press ZONE 2 followed by an input selector
button within 8 seconds.
Zone 2 turns on, the Z2 indicator lights on the AV
receiver’s display.
To select the same source as the main room’s,
press ZONE 2 twice. “Z2 Sel: Source” appears
on the AV receiver’s display.
2
To turn off Zone 2, press OFF.
The zone is turned off.
■ Operating on the remote controller
To control Zone 2, you must press ZONE2 on the
remote controller first.
ZONE2
8RECEIVER
INPUT
SELECTOR
Zone 2
IN
R
Press ZONE2, then point the remote controller
at the AV receiver and press 8RECEIVER.
Zone 2 turns on, the Z2 indicator lights on the AV
receiver’s display.
2
To select an input source for Zone 2, press
ZONE2, followed by an INPUT SELECTOR
button.
3
To turn off Zone 2, press ZONE2, followed by
8RECEIVER.
The zone is turned off.
Input selector buttons
Making Zone 2 Connections
This setup allows 5.1-channel playback in your main
listening room and 2-channel stereo playback in
Zone 2.
1
L
Receiver/
integrated amp
Note
• The volume of Zone 2 must be set on the Zone 2 amplifier.
En-56
Note
• Only analog, NET or USB input source is output from the
ZONE 2 LINE OUT jacks.
• You cannot select different AM or FM radio stations for your
main room and Zone 2. The same AM/FM radio station will
be heard in each room. Namely, if you have selected an FM
station for the main room, that station will also be output in
Zone 2.
• You cannot select different input selector NET or USB for
your main room and Zone 2. Namely, if you have selected
USB input selector for Zone 2, USB input selector will be
selected in main room even if NET has been selected for
main room.
• When Zone 2 is activated and its input selector is selected,
the power consumption of standby mode slightly increases.
• While Zone 2 is on, u functions will not work.
• When setting the AV receiver to standby mode while Zone
2 is active, the Z2 indicator is dimly lit.
• Activating Zone 2 in the main room when the listening
mode is set to Pure Audio (European, Australian and
Asian models) will automatically switch it to Direct.
Controlling Other Components
Controlling Other
Components
You can use the AV receiver’s remote controller to
control your other AV components, including those
made by other manufacturers. This section explains
how to enter the remote control code for a component
that you want to control: DVD, TV, CD, etc.
Preprogrammed Remote Control
Codes
Entering Remote Control Codes
Remapping Colored Buttons
You’ll need to enter a code for each component that
you want to control.
You can change the configuration of colored buttons,
with which REMOTE MODE buttons are preset.
1
Look up the appropriate remote control code
in the separate Remote Control Codes list.
The codes are organized by category (e.g., DVD
player, TV, etc.).
1
2
While holding down the REMOTE MODE
button to which you want to assign a code,
press and hold down DISPLAY (about 3
seconds).
The remote indicator lights.
While holding down the REMOTE MODE
button that you want to program, press and
hold down A (Red) until the remote indicator
lights (about 3 seconds).
You can only change colored buttons for
components whose codes belong to categories
of the Remote Control Codes list (BD/DVD
player, TV, cable set-top box, etc).
2
Within 30 seconds, press the colored buttons
in the order that you want to reassign them.
The button presses are assigned to each button
from left to right. The remote indicator flashes
twice, indicating that the sequence has been
successfully assigned. If the sequence is not
successfully assigned, the remote indicator will
flash once slowly.
The following REMOTE MODE buttons are
preprogrammed with remote control codes for
controlling the components listed. You do not need to
enter a remote control code to control these
components.
For details on controlling these components, see the
indicated pages.
Note
• Remote control codes cannot be entered for
RECEIVER and the multi zone button.
• Only TV remote control codes can be entered for TV.
• Except for RECEIVER, TV, and the multi zone button,
remote control codes from any category can be
assigned for the REMOTE MODE buttons. However,
these buttons also work as input selector buttons, so
choose a REMOTE MODE button that corresponds
with the input to which you connect your component.
For example, if you connect your CD player to the CD
input, choose TV/CD when entering its remote control
code.
BD/DVD Onkyo Blu-ray Disc player (➔ page 59)
TV/CD Onkyo CD player (➔ page 58)
PC
Apple TV
3
Within 30 seconds, use the number buttons to
enter the 5-digit remote control code.
The remote indicator flashes twice.
If the remote control code is not entered
successfully, the remote indicator will flash once
slowly.
Note
• Though the provided remote control codes are correct at
the time of release, they are subject to change.
En-57
Tip
• To reset the REMOTE MODE buttons to their default
settings, see “Resetting the REMOTE MODE Buttons”
(➔ page 58).
Note
• If any other button than the colored buttons is pressed, the
operation will be cancelled.
• This operation cannot be done while the AV receiver is in
Receiver mode or when Zone 2 is active.
Controlling Other Components
` 32901/33104/33504:
Onkyo HD DVD player
` 70868:
Onkyo MD recorder without u
` 71323:
Onkyo CD recorder without u
` 82990:
Onkyo Dock without u
Remote Control Codes for Onkyo
Components Connected via RI
Onkyo components that are connected via u are
controlled by pointing the remote controller at the AV
receiver, not the component. This allows you to
control components that are out of view, in a rack, for
example.
1
2
3
Make sure the Onkyo component is connected
with an u cable and an analog audio cable
(RCA).
See “Connecting Onkyo RI Components” for
details (➔ page 19).
Enter the appropriate remote control code for
a REMOTE MODE button, by referring to the
previous section.
`42157:
Onkyo cassette tape deck with u
`81993:
Onkyo Dock with u
Resetting the REMOTE MODE Buttons
You can reset a REMOTE MODE button to its default
remote control code.
1
While holding down the REMOTE MODE
button that you want to reset, press and hold
down HOME until the remote indicator lights
(about 3 seconds).
2
Within 30 seconds, press the REMOTE MODE
button again.
The remote indicator flashes twice, indicating that
the button has been reset.
Each REMOTE MODE button is preprogrammed
with a remote control code. When a button is
reset, its preprogrammed code is restored.
Press the REMOTE MODE button, point the
remote controller at the AV receiver, and
operate the component.
Controlling Onkyo components without u
If you want to control an Onkyo component by
pointing the remote controller directly at it, or you
want to control an Onkyo component that’s not
connected via u, use the following remote control
codes:
` 30627:
Onkyo DVD player without u
` 71817:
Onkyo CD player without u
` 32900/33100/33500:
Onkyo Blu-ray Disc player
Resetting the Remote Controller
You can reset the remote controller to its default
settings.
1
While holding down RECEIVER, press and
hold down HOME until the remote indicator
lights (about 3 seconds).
2
Within 30 seconds, press RECEIVER again.
The remote indicator flashes twice, indicating that
the remote controller has been reset.
En-58
Controlling Other Components
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your
component, you can control your component as
described below.
For details on entering a remote control code for other
components, see “Entering Remote Control Codes”
(➔ page 57).
Controlling a TV
TV is preprogrammed with the remote control code
for controlling a TV that supports the p*1
(limited to some models). The TV must be able to
receive remote control commands via p and
be connected to the AV receiver via HDMI. If
controlling your TV via p doesn’t work very
well, program your TV’s remote control code into TV
and use the TV remote mode to control your TV.
Use the following remote control codes:
`11807/13100/13500:
TV with p
Controlling Apple TV
By programming the supplied remote controller with
the appropriate remote control code, you can use it to
operate your Apple TV.
Use the following remote control codes:
`02615:
Apple TV
Controlling Other Components
■ TV operation
Controlling a Blu-ray Disc/DVD Player, HD
DVD Player or DVD Recorder
Press the appropriate REMOTE
MODE button first.
a 8, INPUT, TV VOL q/w, g Number: 1 to 9, 0
MUTING
Number: +10*2
BD/DVD is preprogrammed with the remote control
code for controlling a component that supports the
p*1 (limited to some models). The component
must be able to receive remote control commands via
p and be connected to the AV receiver via
HDMI.
Use the following remote control codes:
` 32910/33101/33501/31612:
Blu-ray Disc/DVD player with p
*1
The p supported by the AV receiver is the CEC
system control function of the HDMI standard.
Available buttons
b GUIDE
h
c q/w/e/r, ENTER
d SETUP
e 1, 3, 2, 5, 4,
7, 6*2
i
j
f A (Red)*2
B (Green)*2
i DISPLAY
k CH +/–
l PREV CH
m RETURN
n AUDIO*2
o CLR
C (Yellow)*2
D (Blue)*2
a
k
l
b
c
d
m
n
e
f
■ Blu-ray Disc player/HD DVD player operation
Available buttons
b TOP MENU
h 8SOURCE
c q/w/e/r, ENTER
i DISPLAY
d SETUP
e 1, 3, 2, 5, 4,
7, 6
j MUTING
k CH +/–
DISC +/–
f A (Red)
B (Green)
l MENU
m RETURN
C (Yellow)
n AUDIO*2
o CLR
D (Blue)
g Number: 1 to 9, 0
Number: +10*2
g
o
En-59
Controlling Other Components
Press the appropriate REMOTE
MODE button first.
h
■ DVD player/DVD recorder operation
■ Satellite receiver/Cable receiver operation
Available buttons
Available buttons
b TOP MENU
h 8SOURCE
b GUIDE
h 8SOURCE
c q/w/e/r, ENTER
i DISPLAY
c q/w/e/r, ENTER
i DISPLAY
d SETUP
j MUTING
k CH +/–
d SETUP
j MUTING
k CH +/–
e 1, 3, 2, 5, 4,
7, 6
f A (Red)*2
B (Green)
i
j
b
c
d
k
l
n
e
f A (Red)
B (Green)
AUDIO*2
C (Yellow)
n
D (Blue)*2
o CLR
D (Blue)
■ VCR/PVR operation
■ CD player/CD recorder/MD recorder operation
Available buttons
Available buttons
h 8SOURCE
c q/w/e/r, ENTER
c q/w/e/r, ENTER
i DISPLAY
d SETUP
d SETUP
j MUTING
k CH +/–
e 1, 3, 2, 5, 4,
7, 6
l PREV CH
m RETURN
f SEARCH
REPEAT
e 1, 3, 2, 5, 4,
7, 6
o CLR
Available buttons
o
n AUDIO
o CLR
g Number: 1 to 9, 0
Number: +10
■ Cassette tape deck operation
g
l PREV CH
m RETURN
g Number: 1 to 9, 0
Number: +10*2
g Number: 1 to 9, 0
Number: +10
f
e 1, 3, 2, 5, 4,
7, 6
l MENU
m RETURN
C (Yellow)*2
b GUIDE
m
DISC +/–
RANDOM
g Number: 1 to 9, 0
Number: +10
h 8SOURCE
i DISPLAY
j MUTING
k DISC +/–
o CLR
MODE
Note
h 8SOURCE
e 1, t (Reverse
Playback), 2, 5, 4, j MUTING
7, 6
En-60
• With some components, certain buttons may not work as
expected, and some may not work at all.
• See “Controlling Your iPod/iPhone” about the operation of
iPod/iPhone (➔ page 62).
*2 The p function is not supported. The p
supported by the AV receiver is the CEC system control
function of the HDMI standard.
Controlling Other Components
Using the Onkyo Dock
RI Dock
With the RI Dock, you can easily play the music of
your iPod/iPhone, or watch the slideshows and
videos of your iPod/iPhone on a TV. In addition, the
on-screen display (OSD) allows you to view,
navigate, and select your iPod/iPhone model’s
contents on your TV, and with the supplied remote
controller, you can control your iPod/iPhone from the
comfort of your sofa. You can even use the AV
receiver’s remote controller to operate your
iPod/iPhone.
Note
• Enter the appropriate remote control code before using the
AV receiver’s remote controller for the first time
(➔ page 58).
• Connect the RI Dock to the AV receiver with an u cable
(➔ page 19).
• Set the RI Dock’s RI MODE switch to “HDD” or
“HDD/DOCK”.
• Set the AV receiver’s Input Display to “DOCK”
(➔ page 39).
■ System Function
System On
When you turn on the AV receiver, the RI Dock and
iPod/iPhone turn on automatically. In addition, when
RI Dock and iPod/iPhone are on, the AV receiver can
be turned on by pressing 8SOURCE.
Auto Power On
If you press the remote controller’s 1 (Playback)
while the AV receiver is on standby, the AV receiver
will automatically turn on, select your iPod/iPhone as
the input source, and your iPod/iPhone will start
playback.
automatically switch to the input to which the RI Dock
is connected.
Other Remote Operations
You can use the remote controller that came with the
AV receiver to control other iPod/iPhone functions.
The available functionality depends on the AV
receiver.
Note
• If you use your iPod/iPhone with any other accessories,
iPod/iPhone playback detection may not work.
• The System On function may not work depending on the RI
Dock.
iPod Alarm
If you use the Alarm function on your iPod to start
playback, the AV receiver will turn on at the specified
time and select your iPod as the input source
automatically.
Note
• Depending on your iPod/iPhone model and generation,
some of the linked operations may not be available.
• This linked operation won’t work while a video is being
played or when the sound set for the alarm is a built-in
sound (Beep).
• This linked operation won’t work with models on which
music files cannot be used to set the alarm sound.
■ Operating Notes
• Use the AV receiver’s volume control to adjust the
playback volume.
• While your iPod/iPhone is inserted in the RI Dock,
its volume control has no effect.
• If you do adjust the volume control on your
iPod/iPhone while it’s inserted in the RI Dock, be
careful that it’s not set too loud before you reconnect
your headphones.
Direct Change
If you start iPod/iPhone playback while listening to
another input source, the AV receiver will
En-61
The Dock is sold separately. Models sold are
different depending on the region.
For the latest information on the Onkyo Dock
components, see the Onkyo web site at:
http://www.onkyo.com
Before using the Onkyo Dock components, update
your iPod/iPhone with the latest software, available
from the Apple web site.
For supported iPod/iPhone models, see the
instruction manual of the Onkyo Dock.
Controlling Other Components
■ u Dock operation
Controlling Your iPod/iPhone
Press the appropriate REMOTE
MODE button first.
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your
Dock, you can control your iPod/iPhone in the Dock
with the buttons described further in this section.
See “Entering Remote Control Codes” for details on
entering a remote control code (➔ page 57).
See the Dock’s instruction manual for more
information.
e
f
g
h
RI Dock
• Set the RI Dock’s RI MODE switch to “HDD” or
“HDD/DOCK”.
• 8SOURCE may not work with a remote control
code (without u). In this case, make an u
connection and enter the remote control code 81993
(with u).
■ With the RI Control
Make an u connection and enter the remote control
code 81993 (with u).
• Set the AV receiver’s Input Display to “DOCK”
(➔ page 39).
■ Without the RI Control
You must enter the remote control code 82990 first
(➔ page 58).
Available buttons
i
a
j
b
c
k
d
En-62
a TOP MENU*1
e 8SOURCE*2
b q/w/e/r, ENTER
f DISPLAY*3
PLAYLIST e/r
g MUTING
c 1, 3, 2, 5, 4,
7, 6
h ALBUM +/–
d REPEAT
RANDOM
j MENU
k MODE*4
i VOL q/w
• With some iPod/iPhone models, generations and RI Docks,
certain buttons may not work as expected.
• For detailed operation of iPod/iPhone, please refer to the
instruction manual of the RI Dock.
*1 TOP MENU works as the mode button when used with
the DS-A2 RI Dock.
*2 This button does not turn the Onkyo DS-A2 or DS-A2X
RI Dock on or off. Also, your iPod/iPhone may not
respond the first time you press this button, in which case
you should press it again. This is because the remote
controller transmits the On and Standby commands
alternately, so if your iPod/iPhone is already on, it will
remain on when the remote controller transmits the On
command. Similarly, if your iPod/iPhone is already off, it
will remain off when the remote controller transmits the
Off command.
*3 DISPLAY turns on the backlight for a few seconds.
*4 Resume mode
With the Resume function, you can resume playback of
the song that was playing when you removed your
iPod/iPhone from the Onkyo DS-A2 RI Dock.
Appendix
Troubleshooting
If you have any trouble using the AV receiver, look for
a solution in this section. If you can’t resolve the issue
yourself, contact your Onkyo dealer.
seconds). Within 30 seconds, press RECEIVER
again.
The on-screen menus appear only on a TV that is
connected to the HDMI OUT.
■ Can’t turn on the AV receiver
If you can’t resolve the issue yourself, try resetting the
AV receiver before contacting your Onkyo dealer.
To reset the AV receiver to its factory defaults, turn it
on and, while holding down CBL/SAT, press
8ON/STANDBY. “Clear” will appear on the AV
receiver’s display and the AV receiver will enter
standby mode.
Make sure that the power cord is properly plugged into the
wall outlet.
Unplug the power cord from the wall outlet, wait five
seconds or more, then plug it in again.
■ The AV receiver turns off unexpectedly
The AV receiver will automatically enter standby mode
when Auto Standby has been set and launches.
(➔ page 52)
■ The AV receiver turns off and after restoring the
power, it turns off again
Note that resetting the AV receiver will delete your
radio presets and custom settings.
Remote indicator
The protection circuit has been activated. Remove the
power cord from the wall outlet immediately. Make sure
that all speaker cables and input sources are properly
connected, and leave the AV receiver with its power cord
disconnected for 1 hour. After that, reconnect the power
cord and turn the power on. If the AV receiver turns off
again, avoid resetting it and unplug the power cord. Then
contact your Onkyo dealer. (➔ page 13)
Caution:
RECEIVER
• If “CHECK SP WIRE” appears on the AV receiver’s
display, the speaker cables may be shorting.
Make sure that the digital input source is selected properly.
(➔ page 46)
Make sure that the inputs and outputs of all components
are connected properly. (➔ pages 14 to 19)
Make sure that the polarity of the speaker cables is correct,
and that the bare wires are in contact with the metal part of
each speaker terminal. (➔ page 12)
Make sure that the input source is properly selected.
(➔ page 24)
Make sure that the speaker cables are not shorting.
(➔ page 13)
Check the volume. The AV receiver is designed for home
theater enjoyment. It has a wide volume range, allowing
precise adjustment.
If the MUTING indicator is flashing on the AV receiver’s
display, press the remote controller’s MUTING button to
unmute the AV receiver. (➔ page 39)
While a pair of headphones is connected to the PHONES
jack, no sound is output from the speakers. (➔ page 19)
If there’s no sound from a DVD player connected to an HDMI
IN, check the DVD player’s output settings, and be sure to
select a supported audio format.
Check the digital audio output setting on the connected
device. On some game consoles, such as those that support
DVD, the default setting is off.
With some DVD-Video discs, you need to select an audio
output format from a menu.
If your turntable uses an MC cartridge, you must connect
an MC head amp, or an MC transformer.
WARNING:
HOME
■ There’s no sound, or it’s very quiet
Make sure that all audio connecting plugs are pushed in all
the way. (➔ page 14)
Power
Resetting the AV receiver
Audio
• If smoke, smell or abnormal noise is produced by the AV
receiver, unplug the power cord from the wall outlet
immediately and contact your Onkyo dealer.
Make sure that none of the connecting cables are bent,
twisted, or damaged.
Not all listening modes use all speakers. (➔ page 35)
Specify the speaker distances and adjust the individual
speaker levels. (➔ pages 47, 48)
To reset the remote controller to its factory defaults,
while holding down RECEIVER, press and hold down
HOME until the remote indicator lights (about 3
Make sure that the speaker setup microphone is not still
connected.
En-63
Appendix
If the input signal format is set to “PCM” or “DTS”. Set it to
“Off”. (➔ page 51)
Depending on the input signal, some listening modes
cannot be selected. (➔ pages 35 to 38)
■ Only the front speakers produce sound
■ Can’t select the Pure Audio listening mode
When the Stereo or Mono listening mode is selected, only
the front speakers and subwoofer produce sound.
(➔ page 37)
(European, Australian and Asian models) The Pure
Audio listening mode cannot be selected while Zone 2 is
on.
Make sure the speakers are configured correctly.
(➔ page 46)
■ Can’t get 5.1 playback
■ Only the center speaker produces sound
If you use the Dolby Pro Logic II Movie, Dolby Pro Logic II
Music, or Dolby Pro Logic II Game listening mode with a
mono source, such as an AM radio station or mono TV
program, the sound is concentrated in the center speaker.
Make sure the speakers are configured correctly.
(➔ page 46)
■ The surround speakers produce no sound
When the T-D (Theater-Dimensional), Stereo or Mono
listening mode is selected, the surround speakers produce
no sound.
Depending on the source and current listening mode, not
much sound may be produced by the surround speakers.
Try selecting another listening mode. (➔ page 35)
Depending on the number of connected speakers, it is not
always possible to select all of the listening modes.
(➔ pages 35 to 38)
■ The speaker volume cannot be set as required
After the volume level of each individual speaker has been
adjusted, the maximum volume may be reduced.
(➔ page 48)
Since it takes longer to identify the format of an HDMI
signal than it does for other digital audio signals, audio
output may not start immediately.
■ Noise can be heard
Make sure that each video component is properly
connected. (➔ page 14)
■ The center speaker produces no sound
An audio cable may be picking up interference. Try
repositioning your cables.
When the Stereo or Mono listening mode is selected, the
center speaker produces no sound.
■ The Late Night function doesn’t work
Make sure the speakers are configured correctly.
(➔ page 46)
Make sure the source material is Dolby Digital, Dolby
Digital Plus, and Dolby TrueHD. (➔ page 43)
■ The subwoofer produces no sound
■ About DTS signals
When you play source material that contains no information
in the LFE channel, the subwoofer produces no sound.
When DTS program material ends and the DTS bitstream
stops, the AV receiver remains in DTS listening mode and
the dts indicator remains on. This is to prevent noise when
you use the pause, fast forward, or fast reverse function on
your player. If you switch your player from DTS to PCM,
you may not hear any sound because the AV receiver does
not switch formats immediately. In such case, you should
stop your player for about three seconds and then resume
playback.
Check the digital audio output setting on the connected
device. On some game consoles, such as those that
support DVD, the default setting is off.
■ The beginning of audio received by an HDMI IN
can’t be heard
■ There’s no picture
Make sure the speakers are configured correctly.
(➔ page 46)
■ There’s no sound with a certain signal format
Playing DTS program material, using the pause, fast
forward, or fast reverse function on your player may
produce a short audible noise. This is not a malfunction.
If the volume level of each individual speaker has been
adjusted to high positive values, then the maximum master
volume possible may be reduced. Note that the individual
speaker volume levels are set automatically after the
Audyssey MultEQ® Room Correction and Speaker Setup
has been performed. (➔ pages 21, 48)
Using cable ties to bundle audio cables with power cords,
speaker cables, and the like may degrade the audio
performance, so refrain from doing it.
Make sure the speakers are configured correctly.
(➔ page 46)
With some CD and LD players, you won’t be able to
playback DTS material properly even though your player is
connected to a digital input on the AV receiver. This is
usually because the DTS bitstream has been processed
(e.g., output level, sampling rate, or frequency response
changed) and the AV receiver doesn’t recognize it as a
genuine DTS signal. In such cases, you may hear noise.
With some DVD-Video discs, you need to select an audio
output format from a menu.
En-64
Video
Make sure that all video connecting plugs are pushed in all
the way. (➔ page 17)
If the video source is connected to a component video
input, you must assign that input to an input selector, and
your TV must be connected to COMPONENT VIDEO OUT.
(➔ pages 14, 46)
If the video source is connected to a composite video input,
your TV must be connected to the corresponding
composite video output. (➔ page 14)
If the video source is connected to an HDMI input, you
must assign that input to an input selector, and your TV
must be connected to the HDMI OUT. (➔ pages 14, 45)
(European, Australian and Asian models) While the
Pure Audio listening mode is selected, the analog video
circuitry is turned off and only video signals input through
HDMI IN can be output. (➔ page 35)
On your TV, make sure that the video input to which the AV
receiver is connected is selected.
Appendix
■ There’s no picture from a source connected to
an HDMI IN
Reliable operation with an HDMI-to-DVI adapter is not
guaranteed. In addition, video signals from a PC are not
guaranteed. (➔ page 71)
■ The on-screen menus don’t appear
On your TV, make sure that the video input to which the AV
receiver is connected is selected.
When the AV receiver is not connected to a TV via HDMI
OUT, on-screen menus are not displayed.
Tuner
■ Reception is noisy, FM stereo reception is noisy,
or the FM STEREO indicator doesn’t light
Relocate your antenna.
Move the AV receiver away from your TV or computer.
Listen to the station in mono. (➔ page 32)
When listening to an AM station, operating the remote
controller may cause noise.
If the AV receiver is installed in a rack or cabinet with
colored-glass doors, the remote controller may not work
reliably when the doors are closed.
Make sure you’ve selected the correct remote controller
mode. (➔ pages 10, 58)
Make sure your iPod/iPhone is properly inserted in the
Dock.
Make sure the AV receiver is turned on, the correct input source
is selected, and the volume is turned up.
Make sure the plugs are pushed in all the way.
When using the remote controller to control other
manufacturers’ AV components, some buttons may not
work as expected.
■ There’s no video
Make sure you’ve entered the correct remote control code.
(➔ page 57)
Make sure that your iPod/iPhone model’s TV OUT setting
is set to On.
Make sure to set the same ID on both the AV receiver and
remote controller. (➔ page 51)
Make sure the correct input is selected on your TV or the
AV receiver.
■ Can’t control other components
Some versions of the iPod/iPhone do not output video.
If it’s an Onkyo component, make sure that the u cable
and analog audio cable are connected properly.
Connecting only an u cable won’t be enough.
(➔ page 19)
Make sure you’ve selected the correct remote controller
mode. (➔ pages 10, 58)
Try resetting your iPod/iPhone.
■ The AV receiver’s remote controller doesn’t
control my iPod/iPhone
Make sure your iPod/iPhone is properly inserted in the
Dock. If your iPod/iPhone is in a case, it may not connect
properly to the Dock. Always remove your iPod/iPhone
from the case before inserting it into the Dock.
The iPod/iPhone cannot be operated while it’s displaying
the Apple logo.
Concrete walls weaken radio signals.
If you’ve connected an cassette tape deck or an RI Dock to
the VIDEO/AUDIO IN jacks, for the remote controller to
work properly, you must set the input display appropriately.
(➔ page 39)
If nothing improves the reception, install an outdoor
antenna.
If you cannot operate it, you will need to enter the
appropriate remote control code. (➔ page 57)
When you use the AV receiver’s remote controller, point it
toward your AV receiver.
Passing cars and airplanes can cause interference.
Remote Controller
■ The remote controller doesn’t work
Before operating this unit, be sure to press RECEIVER.
Make sure that the batteries are installed with the correct
polarity. (➔ page 10)
Install new batteries. Don’t mix different types of batteries,
or old and new batteries. (➔ page 10)
Make sure that the remote controller is not too far away
from the AV receiver, and that there’s no obstruction
between the remote controller and the AV receiver’s
remote control sensor. (➔ page 10)
Make sure that the AV receiver is not subjected to direct
sunshine or inverter-type fluorescent lights. Relocate if
necessary.
To control another manufacturer’s component, point the
remote controller at that component. (➔ page 57)
To control an Onkyo component that’s connected via u,
point the remote controller at the AV receiver. Be sure to
enter the appropriate remote control code first.
(➔ page 58)
To control an Onkyo component that’s not connected via
u, point the remote controller at the component. Be sure
to enter the appropriate remote control code first.
(➔ page 58)
The entered remote control code may not be correct. If more
than one code is listed, try each one.
RI Dock for iPod/iPhone
■ There’s no sound
Make sure you’ve selected the right remote mode.
(➔ page 62)
If you still can’t control your iPod/iPhone, start playback by
pressing your iPod/iPhone model’s Play button. Remote
operation should then be possible.
Try resetting your iPod/iPhone.
Depending on your iPod/iPhone, some buttons may not
work as expected.
■ The AV receiver unexpectedly selects my
iPod/iPhone as the input source
Always pause iPod/iPhone playback before selecting a
different input source. If playback is not paused, the Direct
Change function may select your iPod/iPhone as the input
source by mistake during the transition between tracks.
■ iPod/iPhone doesn’t work properly
Try reconnecting your iPod/iPhone.
Make sure your iPod/iPhone is actually playing.
En-65
Appendix
Zone 2
USB Device Playback
■ There’s no sound
■ Can’t access the music files on a USB device
Audio can be output only when analog, NET or USB input
source is selected in Zone 2.
Make sure the USB device is plugged in properly.
■ How do I change the language of a multiplex
source
Use the “Input Ch (Mux)” setting in the “Audio Adjust”
menu to select “Main” or “Sub”. (➔ page 48)
■ The u functions don’t work
■ Can’t access the server or Internet radio
The AV receiver supports USB devices that support the
USB mass storage device class. However, playback may
not be possible with some USB devices even if they
conform to the USB mass storage device class.
(➔ page 72)
Certain network service or contents available through this
device may not be accessible in case the service provider
terminates its service.
Depending on the type of format, the playback from a USB
device may not be performed normally. Check the type of
the file formats that is supported. (➔ page 73)
Check the network connection between the AV receiver
and your router or switch. (➔ page 15)
USB memory devices with security functions cannot be
played.
Make sure that your modem and router are properly
connected, and make sure they are both turned on.
■ The functions System On/Auto Power On and
Direct Change don’t work for components
connected via u
Others
These functions don’t work when Zone 2 is turned on.
(➔ page 19)
Music Server and Internet Radio
Make sure the server is up and running and compatible
with the AV receiver. (➔ page 72)
Check the “11. Network Setup”. (➔ page 54)
■ Playback stops while listening to music files on
the server
Make sure your server is compatible with the AV receiver.
(➔ page 72)
If you download or copy large files on your computer,
playback may be interrupted. Try closing any unused
programs, use a more powerful computer, or use a
dedicated server.
If the server is serving large music files to several
networked devices simultaneously, the network may
become overloaded and playback may be interrupted.
Reduce the number of playback devices on the network,
upgrade your network, or use a switch instead of a hub.
■ Can’t connect to the AV receiver from a Web
browser
If you’re using DHCP, your router may not always allocate
the same IP address to the AV receiver, so if you find that
you can’t connect to a server or Internet radio station,
recheck the AV receiver’s IP address on the “Network
Setup” screen. (➔ page 54)
■ Standby power consumption
In the following cases, the power consumption in standby
mode may reach up to a maximum of 5 W:
– The “HDMI CEC (RIHD)” setting is set to “On”.
(Depending on the TV status, the AV receiver will enter
standby mode as usual.)
– The “HDMI Through” setting is set to other than “Off”.
– The “Network Standby” setting is set to “On”.
(➔ pages 52, 53, 55)
■ The sound changes when I connect my
headphones
When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct, or Pure Audio (European, Australian and
Asian models).
■ The speaker distance cannot be set as required
The values entered may be automatically adjusted with
values best-suited for your home theater.
■ The display doesn’t work
The display is turned off when the Pure Audio (European,
Australian and Asian models) listening mode is selected.
Check the “11. Network Setup”. (➔ page 54)
En-66
To use u, you must make an u connection and an
analog audio connection (RCA) between the component
and AV receiver, even if they are connected digitally.
(➔ page 19)
While Zone 2 is selected, the u functions don’t work.
(➔ page 19)
■ When performing Automatic Speaker Setup, the
measurement fails and the message “Ambient
noise is too high.” is displayed.
This can be caused by a malfunction in your speaker unit.
Check if the unit produces normal sounds.
■ The following settings can be made for the
composite video inputs
You must use the buttons on the unit to make these
settings.
On the AV receiver, press the input selector for the
input source that you want to set and the HOME
button simultaneously. While holding down the
input selector button, press HOME until “Video
ATT :On” appears on the AV receiver’s display.
Then, release both buttons. To turn the setting off,
repeat the above process so that “Video ATT :Off”
appears on the AV receiver’s display, and release
the buttons.
Appendix
• Video Attenuation
This setting can be made for the BD/DVD,
CBL/SAT, GAME, PC, AUX or USB input.
If you have a game console connected to the
composite video input, and the picture isn’t very
clear, you can attenuate the gain.
Video ATT :Off: (default).
Video ATT :On: Gain is reduced by 2 dB.
■ If the picture on your TV/monitor connected to
the HDMI OUT is unstable, try switching the
DeepColor function off
To turn off the DeepColor function, simultaneously
press the GAME and 8ON/STANDBY buttons on
the AV receiver. While holding down GAME, press
8ON/STANDBY until “Deep Color:Off” appears
on the AV receiver’s display. Then, release both
buttons. To reactivate the DeepColor function,
repeat the above process until “Deep Color:On”
appears on the AV receiver’s display and release
the buttons.
The AV receiver contains a microcomputer for
signal processing and control functions. In very rare
situations, severe interference, noise from an
external source, or static electricity may cause it to
lockup. In the unlikely event that this happens,
unplug the power cord from the wall outlet, wait at
least five seconds, and then plug it back in.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused
by the unit’s malfunction. Before you record
important data, make sure that the material will be
recorded correctly.
Before disconnecting the power cord from the wall
outlet, set the AV receiver to standby.
DISCLAIMER
Through this device you are able to link to other
services or websites which are not under the control
of any company which has designed, manufactured
or distributed/have distributed this device, and its
affiliates (collectively, “Company”). We have no
control over the nature, content and availability of
those services. The inclusion of any links does not
necessarily imply a recommendation or endorse the
views expressed within them.
All information, content and services available
through this device belong to third parties and are
protected by copyright, patent, trademark and/or
other intellectual property laws of applicable
countries. The information, content and services
provided through this device are for your personal,
noncommercial use only. Any information, content or
services may not be used in any manner other than
previously approved by the appropriate content
owner or service provider.
You may not modify, copy, republish, translate,
exploit, create derivative works, upload, post,
transmit, sell or distribute in any manner any
information, content or services available through this
device, unless expressly permitted by the appropriate
copyright, patent, trademark and/or other intellectual
property owner, including, without limitation, content
owner or service provider.
THE CONTENT AND SERVICES AVAILABLE
THROUGH THIS DEVICE ARE PROVIDED “AS IS”.
COMPANY DOES NOT WARRANT INFORMATION,
CONTENT OR SERVICES SO PROVIDED, EITHER
EXPRESSLY OR IMPLIEDLY, FOR ANY PURPOSE.
COMPANY EXPRESSLY DISCLAIMS ANY
WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO, WARRANTIES
OF TITLE, NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
En-67
Company makes no representation or warranty of any
kind, express or implied, about the completeness,
accuracy, validity, legality, reliability, suitability or
availability with respect to the information, content or
services available through this device. Company shall
not be liable, whether in contract or tort, including
negligence and strict liability, for any direct, indirect,
special, incidental or consequential damages or any
other damages arising out of, or in connection with,
any information contained in, or as a result of the use
of any content or service by you or any third party,
even if Company has been advised of the possibility
of such damages, nor shall Company be liable for any
third party claims against users of this device or any
third party.
In no event shall Company be responsible nor liable
for, without limiting the generality of the foregoing,
any interruption or suspension of any information,
content or service available through this device.
Company is neither responsible nor liable for
customer service related to the information, content
and services available through this device.
Any question or request for service relating to the
information, content or services should be made
directly to the appropriate content owners and
services providers.
Appendix
Firmware Update
To update the firmware of the AV receiver, you can
choose from the following two methods: update via
network, or update via USB storage. Choose the one
that best suits your environment. Before proceeding
with the update, please read the corresponding
explanations carefully.
■ Update via network
You need a wired Internet connection to update the
firmware.
■ Update via USB storage (➔ page 69)
Please prepare a USB storage device such as a
USB flash memory stick. You need at least 32 MB
of available space to update the firmware.
Limitation of liability
The program and accompanying online
documentation are furnished to you for use at your
own risk. Onkyo will not be liable and you will have
no remedy for damages for any claim of any kind
whatsoever concerning your use of the program or
the accompanying online documentation,
regardless of legal theory, and whether arising in
tort or contract. In no event will Onkyo be liable to
you or any third party for any special, indirect,
incidental, or consequential damages of any kind,
including, but not limited to, compensation,
reimbursement or damages on account of the loss
of present or prospective profits, loss of data, or for
any other reason whatsoever.
Before Starting
• Set the “HDMI CEC (RIHD)” setting to “Off”
(➔ page 52).
• Turn off the controller device connected via network.
• Turn off Multi Zone if this function is present.
• Stop playback of contents from Internet Radio,
iPod/iPhone, USB or servers, etc.
Update Procedure
1
Press RECEIVER followed by HOME on the
remote controller.
The Home menu appears on the TV screen.
2
Select “F/W Update” and press ENTER.
Note that the “F/W Update” option will be grayed
out for a short while after the AV receiver is
turned on. Please wait until it becomes operable.
3
Select “Update via NET” and press ENTER.
Note that this option will not be available if there
is no firmware file newer than the currently
installed version. If the AV receiver is not
connected to the internet, “Update via NET” is
not displayed.
4
Select “Update” and press ENTER.
The update process will begin.
During the update process, the on-screen display
may disappear depending on the updated
program. When this occurs, you can still view the
update progress on the AV receiver’s display.
The on-screen display will reappear after the
update is complete, and upon turning the AV
receiver off and on again.
5
The message “Completed!” appears on the AV
receiver’s display, indicating that the update
has been completed.
See the Onkyo web site for latest information.
Note
• Check the network connection before updating.
• Do not touch any cable or device connected to the AV
receiver during the update process.
• Do not attempt to access the AV receiver from your PC
while it is being updated.
• Do not shutdown the power of the AV receiver while it is
being updated.
• The storage media in the USB card reader may not work.
• If the USB device is partitioned, each section will be treated
as an independent device.
• If the USB device contains a lot of data, the AV receiver
may take a while to read it.
• Operation is not guaranteed for all USB devices, which
includes the ability to power them.
• Onkyo takes no responsibility whatsoever for the loss or
damage of data resulting from the use of a USB device with
the AV receiver. Onkyo recommends that you back up your
important music files beforehand.
• If you connect a USB hard disk drive to the USB port,
Onkyo recommends that you use its AC adapter to power it.
• USB hubs and USB devices with hub functions are not
supported. Do not connect your USB device via a USB hub.
• USB devices with security functions are not supported.
Updating the Firmware via Network
The AV receiver allows you to update the firmware using
network connection on the rear panel.
Note
• Make sure your AV receiver and TV are turned on and an
Ethernet cable is connected to the rear panel of the AV
receiver.
• Never unplug or turn off the AV receiver while it is being
updated.
• Never plug or unplug an HDMI or Ethernet cable during the
update process.
• Do not attempt to access the AV receiver from your PC
while it is being updated.
• Never unplug the power cord during the update process.
• It takes up to 10 minutes to complete the firmware update.
• The AV receiver will retain all your settings after the update
is finished.
En-68
Operating
procedure
(➔ page 44)
Appendix
6
Press 8ON/STANDBY on the front panel.
The AV receiver will enter standby mode.
Do not use 8RECEIVER on the remote
controller.
The AV receiver will enter standby mode
automatically in 3 minutes regardless of whether
8ON/STANDBY is pressed.
Congratulations! You now have the latest
firmware installed on your Onkyo AV receiver.
■ Errors during an update via network
Error Code
Description
*-01, *-10
The Ethernet cable was not detected.
Reconnect the cable properly.
*-02, *-03,
Internet connection error.
Check the following items:
• Make sure the IP address, subnet mask,
gateway address, and DNS server are
configured properly.
• Make sure the router is turned on.
• Make sure the AV receiver and the router
are connected with an Ethernet cable.
• Make sure your router is configured
properly. See the instruction manual of
the router.
• If your network allows only one client
connection and there is any other device
already connected, the AV receiver will
not be able to access the network.
Consult your Internet Service Provider
(ISP).
• If your modem does not function as a
router, you will need a router. Depending
on your network, you may need to
configure the proxy server if necessary.
See the document provided by your ISP.
If you are still unable to access the
Internet, the DNS or proxy server may be
temporarily down. Contact your ISP.
*-04, *-05,
*-06, *-11,
*-13, *-14,
*-16, *-17,
*-18, *-20,
*-21
Troubleshooting
Case 1:
If an error occurs, “Error!! *-**” is displayed on the AV
receiver’s display. (Alpha-numeric characters on the
front display are denoted by asterisks.) Refer to the
following table and take appropriate action.
Others
Updating the Firmware via USB
The AV receiver allows you to update the firmware
using a USB device.
Note
• Never unplug or turn off the AV receiver during the update
process.
• Never plug or unplug an HDMI cable or a USB device
during the update process.
• Never unplug the USB storage device containing the
firmware file or the AC power cord during the update
process.
• Do not attempt to access the AV receiver from your PC
while it is being updated.
• It takes up to 10 minutes to complete the firmware update.
• The AV receiver will retain all your settings after the update
is finished.
Before Starting
• Set the “HDMI CEC (RIHD)” setting to “Off”
(➔ page 52).
• Turn off the controller device connected via network.
• Turn off Multi Zone if this function is present.
• Stop playback of contents from Internet Radio,
iPod/iPhone, USB or servers, etc.
• If there is any data in the USB device, remove it first.
Retry the update procedure from the
beginning. If the error persists, please
contact Onkyo Suport and provide the
error code.
Case 2:
If an error occurs during the update process,
disconnect then reconnect the AC power cord and try
again.
Case 3:
If you do not have an Internet connection to the
network, please contact Onkyo Support.
En-69
Operating
procedure
(➔ page 44)
Appendix
Update Procedure
1
Connect a USB device to your PC. If there is
any data in the USB device, remove it first.
2
Download the firmware file from the Onkyo
web site. The file name is as follows:
ONKAVR****_************.zip
9
10
Unzip the downloaded file. The numbers of
folders and files differ according to the model.
3
Copy all the extracted folders including all
folders and files to the root folder of the USB
device. Be careful not to copy the zip file.
4
Remove the USB device from your PC and
connect it to the USB port on the AV receiver.
When the AV receiver has two USB ports, you
can use either one.
5
6
Make sure the AV receiver and TV are turned
on.
If the AV receiver is in standby mode, press
8ON/STANDBY on the AV receiver to light up
the front display.
Select the USB input source.
“Now Initializing...” appears on the AV receiver’s
display and then the name of the USB device is
displayed. It takes 20 to 30 seconds to recognize
the USB device.
7
Press RECEIVER followed by HOME on the
remote controller.
The Home menu appears on the TV screen.
8
Select “F/W Update” and press ENTER.
11
12
Select “Update via USB” and press ENTER.
Note that this option will not be available if there
is no firmware file newer than the currently
installed version. If the AV receiver is not
connected to the internet, “Update via USB” is
not displayed.
Select “Update” and press ENTER.
The update process will begin.
During the update process, the on-screen display
may disappear depending on the updated
program. When this occurs, you can still view the
update progress on the AV receiver’s display.
The on-screen display will reappear after the
update is complete, and upon turning the AV
receiver off and on again.
Do not turn off the AV receiver and do not
remove the USB device during the update
process.
The message “Completed!” appears on the AV
receiver’s display, indicating that the update
has been completed.
Remove the USB device.
Press 8ON/STANDBY on the front panel.
The AV receiver will enter standby mode.
Do not use 8RECEIVER on the remote
controller.
The AV receiver will enter standby mode
automatically in 3 minutes regardless of whether
8ON/STANDBY is pressed.
Congratulations! You now have the latest
firmware installed on your Onkyo AV receiver.
En-70
Troubleshooting
Case 1:
If an error occurs, “Error!! *-**” is displayed on the AV
receiver’s display. (Alpha-numeric characters on the
front display are denoted by asterisks.) Refer to the
following table and take appropriate action.
■ Errors during an update via USB
Error Code
Description
*-01, *-10
The USB device was not detected. Make
sure the USB flash memory or USB cable is
properly connected to the USB port. If the
USB storage device has its own power
supply, use it to power the USB device.
*-05, *-13,
The firmware file was not found in the root
folder of the USB device, or the firmware
file is for another model. Retry and
download the file on the support page of
the web site, following the on-site
instructions. If the error persists, please
contact Onkyo Support and provide the
error code.
*-20, *-21
Others
Retry the update procedure from the
beginning. If the error persists, please
contact Onkyo Support and provide the
error code.
Case 2:
If an error occurs during the update process,
disconnect then reconnect the AC power cord and try
again.
Operating
procedure
(➔ page 44)
Appendix
About HDMI
Designed to meet the increased demands of digital
TV, HDMI (High Definition Multimedia Interface) is a
new digital interface standard for connecting TVs,
projectors, Blu-ray Disc players/DVD players, set-top
boxes, and other video components. Until now,
several separate video and audio cables have been
required to connect AV components. With HDMI, a
single cable can carry control signals, digital video,
and up to eight channels of digital audio (2-channel
PCM, multichannel digital audio, and multichannel
PCM).
The HDMI video stream (i.e., video signal) is
compatible with DVI (Digital Visual Interface)*1, so
TVs and displays with a DVI input can be connected
by using an HDMI-to-DVI adapter cable. (This may
not work with some TVs and displays, resulting in no
picture.)
The AV receiver uses HDCP (High-bandwidth Digital
Content Protection)*2, so only HDCP-compatible
components can display the picture.
Supported Audio Formats
• 2-channel linear PCM (32–192 kHz, 16/20/24 bit)
• Multichannel linear PCM (up to 7.1 ch, 32–192 kHz,
16/20/24 bit)
• Bitstream (DSD, Dolby Digital, Dolby Digital Plus,
Dolby TrueHD, DTS, DTS-HD High Resolution
Audio, DTS-HD Master Audio)
Your Blu-ray Disc player/DVD player must also
support HDMI output of the above audio formats.
About Copyright Protection
The AV receiver supports HDCP (High-bandwidth
Digital Content Protection)*2, a copy-protection
system for digital video signals. Other devices
connected to the AV receiver via HDMI must also
support HDCP.
*1
*2
*3
DVI (Digital Visual Interface): The digital display interface
standard set by the DDWG*3 in 1999.
HDCP (High-bandwidth Digital Content Protection): The
video encryption technology developed by Intel for
HDMI/DVI. It’s designed to protect video content and
requires a HDCP-compatible device to display the
encrypted video.
DDWG (Digital Display Working Group): Lead by Intel,
Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and
Silicon Image, this open industry group’s objective is to
address the industry’s requirements for a digital
connectivity specification for high-performance PCs and
digital displays.
Note
The AV receiver’s HDMI interface is based on the
following:
Audio Return Channel, 3D, x.v.Color, DeepColor, Lip
Sync, 4K Passthrough, DTS-HD Master Audio, DTSHD High Resolution Audio, Dolby TrueHD, Dolby
Digital Plus, DSD and Multichannel PCM.
• The HDMI video stream is compatible with DVI (Digital
Visual Interface), so TVs and displays with a DVI input can
be connected by using an HDMI-to-DVI adapter cable.
(Note that DVI connections only carry video, so you’ll need
to make a separate connection for audio.) However,
reliable operation with such an adapter is not guaranteed.
In addition, video signals from a PC are not supported.
• The HDMI audio signal (sampling rate, bit length, etc.) may
be restricted by the connected source component. If the
picture is poor or there’s no sound from a component
connected via HDMI, check its setup. Refer to the
connected component’s instruction manual for details.
En-71
Appendix
Network/USB Features
Network Requirements
■ Ethernet Network
For the best results, a 100Base-TX switched Ethernet
network is recommended. Although it’s possible to
play music on a computer that’s connected to the
network wirelessly, playback may be unreliable, so it
is recommended to use wired connections.
■ Ethernet Router
A router manages the network, data-routing and
supplying of IP addresses. Your router must support
the following:
• NAT (Network Address Translation). NAT allows
several networked computers to access the Internet
simultaneously via a single Internet connection. The
AV receiver needs Internet access for Internet radio.
• DHCP (Dynamic Host Configuration Protocol).
DHCP supplies IP addresses to the network
devices, allowing them to configure themselves
automatically.
• A router with a built-in 100Base-TX switch is
recommended.
Some routers have a built-in modem, and some
Internet Service Providers (ISP) require you to use
specific routers. Please consult your ISP or computer
dealer if you’re unsure.
■ CAT5 Ethernet cable
Use a shielded CAT5 Ethernet cable (straight-type) to
connect the AV receiver to your home network.
■ Internet Access (for Internet radio)
To receive Internet radio, your Ethernet network must
have Internet access. A narrowband Internet
connection (e.g., 56K modem, ISDN) will not provide
satisfactory results, so a broadband connection is
strongly recommended (e.g., cable modem, xDSL
modem, etc). Please consult your ISP or computer
dealer if you’re unsure.
Note
• To receive Internet radio with the AV receiver, your
broadband Internet connection must be working and able to
access the Web. Consult your ISP if you have any problems
with your Internet connection.
• The AV receiver uses DHCP to configure its network
settings automatically. If you want to configure these
settings manually, see “11. Network Setup” (➔ page 54).
• The AV receiver does not support PPPoE settings, so if you
have a PPPoE-type Internet connection, you must use a
PPPoE-compatible router.
• Depending on your ISP, you may need to specify a proxy
server to use Internet radio. If your computer is configured
to use a proxy server, use the same settings for the AV
receiver (➔ page 54).
Server Requirements
■ Server playback
The AV receiver can play digital music files stored on
a computer or media server and supports the
following technologies:
• Windows Media Player 11
• Windows Media Player 12
• DLNA-certified media server
• The computer or media server must be on the same
network as the AV receiver.
• Up to 20,000 folders can be displayed, and folders
may be nested up to 16 levels deep.
Note
• Depending on the media server, the AV receiver may not
recognize it, or may not be able to play its music files.
■ Remote playback
• Windows Media Player 12
• DLNA-certified (within DLNA Interoperability
Guidelines version 1.5) media server or controller
device.
En-72
The setting varies depending on the media server or
controller devices. Refer to your devices’ instruction
manual for details.
If the operating system of your personal computer is
Windows 8/Windows 7, Windows Media Player 12 is
already installed. For more information, see the
Microsoft web site.
USB Device Requirements
• USB mass storage device class (but not always
guaranteed).
• FAT16 or FAT32 file system format.
• If the storage device has been partitioned, each
section will be treated as an independent device.
• Up to 20,000 folders can be displayed, and folders
may be nested up to 16 levels deep.
• USB hubs and USB devices with hub functions are
not supported.
Note
• If the media you connect is not supported, the message “No
Storage” will be displayed.
• If you connect a USB hard disk drive to the AV receiver’s
USB port, we recommend that you use its AC adapter to
power it.
• The AV receiver supports USB MP3 players that support
the USB Mass Storage Class standard, which allows USB
devices to be connected to computers without the need for
special drivers or software. Note that not all USB MP3
players support the USB Mass Storage Class standard.
Refer to your USB MP3 player’s instruction manual for
details.
• Protected WMA music files on an MP3 player cannot be
played.
• Onkyo accepts no responsibility whatsoever for the loss or
damage to data stored on a USB device when that device
is used with the AV receiver. We recommend that you back
up your important music files beforehand.
• MP3 players containing music files that are managed with
special music software are not supported.
Appendix
• Operation is not guaranteed for all USB devices, which
includes the ability to power them.
• Do not connect your USB device via a USB hub. The USB
device must be connected directly to the AV receiver’s USB
port.
• If the USB device contains a lot of data, the AV receiver
make take a while to read it.
• USB devices with security functions cannot be played.
Supported Audio File Formats
For server playback and playback from a USB device,
the AV receiver supports the following music file
formats.
Variable bit-rate (VBR) files are supported. However,
playback times may not display correctly.
Note
• With remote playback, the AV receiver does not support the
following music file formats: FLAC, Ogg Vorbis, DSD and
Dolby TrueHD.
• In the case of server playback, the above-mentioned file
formats may not be played depending on the server type.
■ MP3 (.mp3 or .MP3)
• MP3 files must be MPEG-1/MPEG-2 Audio Layer 3
format with sampling rates of 8 kHz, 11.025 kHz,
12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz,
44.1 kHz, 48 kHz and bitrates of between 8 kbps
and 320 kbps. Incompatible files cannot be played.
■ WMA (.wma or .WMA)
WMA stands for Windows Media Audio and is an
audio compression technology developed by
Microsoft Corporation. Audio can be encoded in WMA
format by using Windows Media® Player.
• WMA files must have the copyright option turned off.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, bitrates of between 5 kbps and 320 kbps,
and WMA DRM are supported.
• WMA Pro/Voice formats are not supported.
■ WMA Lossless (.wma or .WMA)
• Sampling rates of 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz are supported.
• Quantization bit: 16 bit, 24 bit
■ WAV (.wav or .WAV)
WAV files contain uncompressed PCM digital audio.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, 64 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and
192 kHz are supported.
• Quantization bit: 8 bit, 16 bit, 24 bit
*
For playback from a USB (Rear) device, sampling rates of
176.4 kHz and 192 kHz are not supported.
■ AAC
(.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/.MP4/
.3GP or .3G2)
AAC stands for MPEG-2/MPEG-4 Audio.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, 64 kHz, 88.2 kHz, 96 kHz and bitrates of
between 8 kbps and 320 kbps are supported.
■ FLAC (.flac or .FLAC)
FLAC is a file format for lossless audio data
compression.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, 64 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and
192 kHz are supported.
• Quantization bit: 8 bit, 16 bit, 24 bit
■ Ogg Vorbis (.ogg or .OGG)
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz and bitrates of between 48 kbps and
500 kbps are supported. Incompatible files cannot
be played.
En-73
■ LPCM (Linear PCM)
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, 64 kHz, 88.2 kHz and 96 kHz are
supported.
• Quantization bit: 8 bit, 16 bit, 24 bit
*
Only for playback via network.
■ Apple Lossless (.m4a/.mp4/.M4A/.MP4)
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, 64 kHz, 88.2 kHz and 96 kHz are
supported.
• Quantization bit: 16 bit, 24 bit
■ DSD (.dsf or .DSF)
• The sampling rate of 2.8224 MHz is supported.
■ Dolby TrueHD (.vr/.mlp/.VR/.MLP)
• Sampling rates of 48 kHz, 64 kHz, 88.2 kHz,
96 kHz, 176.4 kHz and 192 kHz are supported.
*
For playback from a USB (Rear) device, sampling rates
only of 48 kHz and 64 kHz are supported.
About DLNA
The Digital Living Network Alliance is an international,
cross-industry collaboration. Members of DLNA
develop a concept of wired and wireless interoperable
networks where digital content such as photos,
music, and videos can be shared through consumer
electronics, personal computers, and mobile devices
in and beyond the home. The AV receiver complies
with the DLNA Interoperability Guidelines version 1.5.
Appendix
License and Trademark
Information
Windows and the Windows logo are trademarks of the
Microsoft group of companies.
“x.v.Color” is a trademark of Sony Corporation.
Manufactured under license under U.S. Patent Nos:
5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,212,872;
7,333,929; 7,392,195; 7,272,567 & other U.S. and
worldwide patents issued & pending. DTS-HD, the Symbol,
& DTS-HD and the Symbol together are registered
trademarks of DTS, Inc. Product includes software. © DTS,
Inc. All Rights Reserved.
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic and the double-D symbol are trademarks
of Dolby Laboratories.
iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and
iPod touch are trademarks of Apple Inc., registered in the
U.S. and other countries.
“Made for iPod” and “Made for iPhone” mean that an
electronic accessory has been designed to connect
specifically to iPod or iPhone, respectively, and has been
certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation of this
device or its compliance with safety and regulatory
standards.
Please note that the use of this accessory with iPod or
iPhone may affect wireless performance.
Apple TV is a trademark of Apple Inc., registered in the
U.S. and other countries.
Music Optimizer™ and “WRAT” are trademarks of Onkyo
Corporation.
“The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing LLC in the United States
and other countries.”
Manufactured under license from
Audyssey Laboratories™,Inc. U.S. and foreign patents
pending. Audyssey MultEQ®, Audyssey Dynamic EQ® and
Audyssey Dynamic Volume® are registered trademarks of
Audyssey Laboratories,Inc.
“DLNA®, the DLNA Logo and DLNA CERTIFIED® are
trademarks, service marks, or certification marks of the
Digital Living Network Alliance.”
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
InstaPrevue and the InstaPrevue logo are trademarks or
registered trademarks of Silicon Image, Inc. in the United
States and other countries.
This product is protected by certain intellectual property
rights of Microsoft. Use or distribution of such technology
outside of this product is prohibited without a license from
Microsoft.
En-74
Appendix
■ HDMI
Specifications
Video Section
Amplifier Section
Input Sensitivity/Output Level and Impedance
1 Vp-p/75 Ω (Component Y)
0.7 Vp-p/75 Ω (Component PB/CB,
PR/CR)
1 Vp-p/75 Ω (Composite)
Component Video Frequency Response
5 Hz - 100 MHz/+0 dB, –3 dB
Rated Output Power
All channels:
80 watts minimum continuous power
per channel, 8 ohm loads, 2 channels
driven from 20 Hz to 20 kHz, with a
maximum total harmonic distortion of
0.7% (FTC)
(North American)
5 ch × 130 W at 6 ohms, 1 kHz, 1 ch
driven of 1% (IEC)
(Others)
Maximum Effective Output Power
5 ch × 160 W at 6 ohms, 1 kHz, 1 ch
driven (JEITA)
(Asian)
Dynamic Power*
* IEC60268-Short-term maximum output power
180 W (3 Ω, Front)
160 W (4 Ω, Front)
100 W (8 Ω, Front)
THD+N (Total Harmonic Distortion+Noise)
0.7% (20 Hz - 20 kHz, half power)
Damping Factor
60 (Front, 1 kHz, 8 Ω)
Input Sensitivity and Impedance (Unbalance)
200 mV/47 kΩ (LINE)
Rated RCA Output Level and Impedance
200 mV/2.2 kΩ (LINE OUT)
Maximum RCA Output Level and Impedance
2 V/2.2 kΩ (LINE OUT)
Frequency Response 5 Hz - 100 kHz/+1 dB, –3 dB
(DSP bypass)
Tone Control Characteristics
±10 dB, 30 Hz (BASS)
±10 dB, 20 kHz (TREBLE)
Signal to Noise Ratio 100 dB (LINE, IHF-A)
Speaker Impedance 6 Ω - 16 Ω
Input
Output
Video Resolution
Audio Format
Supported
IN 1, IN 2, IN 3, IN 4, IN 5, IN 6
OUT
4K
Dolby TrueHD, DTS-HD Master Audio,
DVD-Audio, DSD
3D, Audio Return Channel, DeepColor,
x.v.Color, LipSync, CEC (RIHD),
4K Passthrough
■ Video Inputs
Tuner Section
FM Tuning Frequency Range
87.5 MHz - 107.9 MHz
(North American and Taiwanese)
87.5 MHz - 108.0 MHz, RDS (Others)
AM Tuning Frequency Range
522/530 kHz - 1611/1710 kHz
Preset Channel
40
General
Component
Composite
■ Video Outputs
Component
Composite
AC 120 V, 60 Hz
(North American and Taiwanese)
AC 230 V, 50 Hz
(European and Australian)
AC 220 - 240 V, 50/60 Hz (Others)
Power Consumption 4.2 A (North American and Taiwanese)
400 W (European and Australian)
420 W (Others)
No-sound Power Consumption
60 W
(North American, European, Australian
and Taiwanese)
60 W (230 V)
65 W (240 V)
(Others)
Stand-by Power Consumption
0.1 W (North American and Taiwanese)
0.2 W (Others)
Dimensions (W × H × D)
435 mm × 173.5 mm × 328 mm
17-1/8" × 6-13/16" × 12-15/16"
Weight
8.5 kg (18.7 lbs.)
(North American and Taiwanese)
9.0 kg (19.8 lbs.) (Others)
En-75
OUT
MONITOR OUT
■ Audio Inputs
Digital
Power Supply
IN 1, IN 2
BD/DVD, CBL/SAT, GAME, PC, AUX
Analog
Optical: 1
Coaxial: 2
BD/DVD, CBL/SAT, GAME, PC, TV/CD,
AUX
■ Audio Outputs
Analog
ZONE2 LINE OUT
Subwoofer Pre Outputs
2
Speaker Outputs
Main (L, R, C, SL, SR)
Phones
1 (ø 6.3)
■ Others
Setup Mic
RI
USB
Ethernet
1
1
1 (Front)/1 (Rear)
1
Specifications and features are subject to change
without notice.
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
http://www.onkyo.com/
The Americas
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
For Dealer, Service, Order and all other Business Inquiries:
Tel: 201-785-2600 Fax: 201-785-2650
http://www.us.onkyo.com/
For Product Support Team Only:
1-800-229-1687
http://www.us.onkyo.com/
Europe
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
http://www.eu.onkyo.com/
Unit 19, Building 6, Croxley Green Business Park, Hatters Lane, Watford, WD18 8YH, UK
Tel: +44 (0)8712-00-19-96 Fax: +44 (0)8712-00-19-95
China
(Hong Kong)
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.hk.onkyo.com/
(Mainland)
1301, 555 Tower, No.555 West NanJing Road, Jing’an District, Shanghai, China 200041,
Tel: 86-21-52131366 Fax: 86-21-52130396
http://www.cn.onkyo.com/
Asia, Oceania, Middle East, Africa
Please contact an Onkyo distributor referring to Onkyo SUPPORT site.
http://www.intl.onkyo.com/support/
The above-mentioned information is subject to change without prior notice.
Visit the Onkyo web site for the latest update.
Y1303-3
SN 29401399EN-B (C) Copyright 2013 Onkyo Corporation Japan. All rights reserved.
* 2 9 4 0 1 3 9 9 E N - B *
Using Internet Radio
Using Internet Radio
Common Procedures in Internet Radio
Menu
Note
• Available services may vary depending on the region.
• Certain network service or contents available through this
device may not be accessible in case the service provider
terminates its service.
1
2
Press NET.
A list of the network services appears, and the
NET indicator lights. If it flashes, verify that the
Ethernet cable is firmly connected to the AV
receiver.
Select the desired service and press ENTER.
The top page of the selected service appears.
Using Multiple Accounts
The AV receiver supports multiple user accounts,
which means you can freely switch between several
logins. After registering user accounts, login is
performed from the “Users” screen.
Pandora® internet radio
–Getting Started (U.S. only)..................... 2
Using Rhapsody (U.S. only).......................... 3
1
Press MENU while the Users screen is
displayed.
The following menu items appear:
Add new user:
Remove this user:
You can either store a new user account, or
delete an existing one.
Using the SiriusXM Internet Radio
(North American only).............................. 4
Using Last.fm Internet Radio ........................ 5
Tip
• Some of the services don’t allow the use of multiple user
accounts.
• You can store up to 10 user accounts.
• To switch between accounts you must first log out from the
current account, and log in again on the “Users” screen.
En-1
Using Slacker Personal Radio ...................... 6
Using MP3tunes ............................................. 7
Using Internet Radio
Pandora® internet radio
–Getting Started (U.S. only)
Pandora is a free, personalized Internet radio service
that plays the music you know and helps you discover
music you’ll love.
1
Use q/w to select “I have a Pandora Account”
or “I’m new to Pandora” and then press
ENTER.
If you are new to Pandora select “I’m new to
Pandora”. You will see an activation code on
your TV screen. Please write down this code. Go
to an Internet connected computer and point your
browser to www.pandora.com/onkyo
Enter your activation code and then follow the
instructions to create your Pandora account and
your personalized Pandora Internet radio
stations. You can create your stations by entering
your favorite tracks and artists when prompted.
After you have created your account and stations
you can return to your Onkyo receiver and press
enter to begin listening to your personalized
Pandora Internet radio.
If you have an existing Pandora account, you can
add your Pandora account to your Onkyo
receiver by selecting “I have a Pandora
Account” and logging in with your email and
password.
2
To play a station, use q/w to select the station
from your station list, and then press ENTER.
Playback starts and the playback screen
appears.
Create a New Station:
Enter the name of a track, artist, or genre and
Pandora will create a unique radio station for you
based on the musical qualities of that track, artist,
or genre.
■ Menu Items
I like this track:
Give a track “thumbs-up” and Pandora will play
more music like it.
I don’t like this track:
Give a track “thumbs-down” and Pandora will ban
that track from the current station.
Why is this track playing?:
Discover some of the musical attributes that
Pandora uses to create your personal radio
stations.
I’m tired of this track:
If you are tired of a track, you can put the track to
sleep and Pandora will not play it for one month.
Create station from this artist:
Creates a radio station from this artist.
Tip
• If you want to use multiple user accounts, see “Using
Multiple Accounts” (➔ page 1). Login can be made
from the “Users” screen.
En-2
Delete this station:
This will permanently delete a station from your
Pandora account. All of your thumbs feedback
will be lost should you choose to re-create the
station with the same track or artist.
Create station from this track:
Creates a radio station from this track.
Rename this station:
Lets you rename the current radio station.
Bookmark this artist:
Pandora will bookmark your favorite artist for
your profile on www.pandora.com.
Bookmark this track:
Pandora will bookmark the current track and
allow you to buy them all from Amazon or iTunes
in one step!
Add to My Favorites:
Adds a station to My Favorites list.
PANDORA, the PANDORA logo, and the Pandora
trade dress are trademarks or registered trademarks
of Pandora Media, Inc. Used with permission.
Using Internet Radio
Using Rhapsody (U.S. only)
1
Use q/w to select “Sign in to your account”
and then press ENTER.
To use Rhapsody, you need an account. If you
don’t have one yet, you can create a new
account at
www.rhapsody.com/onkyo
If you have an existing Rhapsody account, select
“Sign in to your account” and press ENTER.
Enter your user name (usually your email) and
password in the next keyboard screen, or in Web
Setup.
■ Using the keyboard screen
1. Use q/w/e/r and ENTER to enter your user
name and password.
2. Select “OK”.
3. Press ENTER. The “Confirm your entries”
screen appears.
4. Press ENTER.
Tip
2
Use q/w to select the menu, then press
ENTER.
Search:
You can search for music by Artist, Album, or
Track.
Music Guide:
You can play tracks from Genres, Top Artists,
Top Albums, Top Tracks, New Releases, and
Staff Picks.
Rhapsody Channels:
Listen to radio channels programmed by
Rhapsody’s top-notch editors.
Playlists:
Play your own personal playlists.
My Library:
Bookmark your favorite albums and tracks from
the Rhapsody catalog using My Library.
Account Info:
Confirm your account information.
Sign Out:
Sign out from your Rhapsody account.
• If you want to use multiple user accounts, see “Using
Multiple Accounts” (➔ page 1). Login can be made
from the “Users” screen.
3
Use q/w to select a channel, and press ENTER
or 1 to start playback.
Playback starts and the playback screen
appears.
You can control the tracks with the buttons on the
remote control.
Enabled buttons: 1, 3, 2, 5, 4, 7,
6, RANDOM, REPEAT
Note
• On Rhapsody Channels, some of the buttons don’t
work.
■ Menu Items
Add track to My Library:
Bookmark currently-playing tracks.
Add album to My Library:
Bookmark currently-playing albums.
Add playlist to My Library:
Bookmark currently-playing playlists.
Add channel to My Channels:
Bookmark currently-playing Rhapsody radio
channels.
Add to My Favorites:
Adds a track, channel or playlist to My Favorites
list.
Tip
• You can remove bookmarked tracks, albums, and
Rhapsody Channels from My Library.
En-3
Using Internet Radio
Using the SiriusXM Internet Radio
(North American only)
1
Your Onkyo AV receiver includes a free trial of
SiriusXM Internet Radio. The “Account Info” screen
shows how many days are left in your trial. After the
trial period expires, if you want to continue listening to
the service, you must subscribe. To subscribe go to
www.siriusxm.com/internetradio with your
computer.
Use q/w to select “Sign In”, and then press
ENTER.
If you have an existing SIRIUS account, you can
sign in by selecting “Sign In”. Enter your user
name and password in the next keyboard screen,
or in Web Setup. If you don’t know your
username or password, call Sirius XM at (888)
539-7474 for assistance.
Tip
• If you want to use multiple user accounts, see “Using
Multiple Accounts” (➔ page 1). Login can be made
from the “Users” screen.
When you subscribe, you will be provided with a
username and password which has to be entered into
the AV receiver.
■ Using the keyboard screen
1. Use q/w/e/r and ENTER to enter your user
name and password.
2. Select “OK”.
3. Press ENTER. The “Confirm your entries”
screen appears.
4. Press ENTER.
“Please wait...” appears and then “SiriusXM
Internet Radio” screen appears which displays
the category available for selection.
To use SiriusXM Internet Radio, you must have your
AV receiver connected to the Internet. Using the
remote control, follow these steps:
2
Use q/w to select the category and then press
ENTER.
The channel list screen for the selected category
appears.
En-4
3
Use q/w to select the desired channel and then
press ENTER.
The playback screen for the selected channel
appears and you can listen to SiriusXM Internet
Radio.
You can control the tracks with the buttons on the
remote control.
Enabled buttons: 2, 3, 7, 6
■ Menu Items
Add to My Favorites:
Adds a channel to My Favorites list.
SiriusXM Internet Radio subscriptions are sold
separately and are governed by the Sirius Terms and
Conditions (see www.sirius.com). Be sure to read this
agreement before you purchase your subscription.
Sirius, XM and all related marks and logos are
trademarks of Sirius XM Radio Inc. and its
subsidiaries. All rights reserved.
Using Internet Radio
Using Last.fm Internet Radio
1
Last.fm is a music service that learns what you
love...
Your new Onkyo AV receiver is very clever. If you
have a free Last.fm account, it will keep track of all
the songs you’ve just played. When you visit the
Last.fm website, you can see personal charts of the
music you’ve enjoyed, share them with friends and
see what they like, too.
■ Using the keyboard screen
1. Use q/w/e/r and the ENTER to enter your
user name and password.
2. Select “OK”.
3. Press ENTER. The “Confirm your entries”
screen appears.
4. Press ENTER.
“Please wait...” appears and then “Last.fm
Internet Radio” screen appears.
With thousands of biographies, reviews and an
endless choice of personalised, ad-free radio
stations, Last.fm is a great way to discover music.
Pick up your free Last.fm account today at
www.last.fm/join
Get a subscription and you can enjoy the best of adfree Last.fm Radio on your Onkyo AV receiver without
a computer!
Recommended Radio:
Discover smart personalised recommendations that
adapt as your tastes change.
Artist Radio:
Pick any artist and we’ll play you a whole station of
music inspired by your choice.
My Library:
Sit back and enjoy selections from all the music
you’ve heard since you joined Last.fm.
Tag Radio:
Polish funk? Death pop? Think of a style and we’ll
entertain you with it for hours.
Start your free trial straight away when you create
your account and see for yourself what it’s like to
have the world’s music at your fingertips. Latest
prices and full information are available at
www.last.fm/subscribe
Profile:
You can play tracks from “Recently Listened
Tracks”, “Library” and “Neighbours”.
Account Info:
Confirm your account information.
Sign Out:
It signs out from your account.
Use q/w to select “Sign in to your account”,
and then press ENTER.
If you have the existing Last.fm account, you can
sign in to your account to select “Sign in to your
account”. Enter your user name and password in
the next keyboard screen.
3
■ Menu Items
I Love this track:
Track information is saved in Last.fm server, and
playback frequency increases.
Ban this track:
Track information is saved in Last.fm server, and
playback frequency reduces.
Add to My Favorites:
Adds a station to My Favorites list.
Tip
• If you want to use multiple user accounts, see “Using
Multiple Accounts” (➔ page 1). Login can be made
from the “Users” screen.
2
Use q/w to select menu and then press
ENTER.
Search Station:
You can search station by Artist, Tag, or User
Name.
Top Artists Station:
You can play tracks of top-rated artists.
Top Tags Station:
You can play tracks of top-rated tags.
Personal Station:
• You can play tracks from personalized station
(“Your Library”, “Your Neighbourhood” and
“Your Recommendations”).
En-5
Use q/w to select a station, and press ENTER
or 1 to start playback.
Playback starts and the playback screen
appears.
■ Using scrobbling control
Use q/w to select “Enable”, and then press ENTER.
*
Internet radio services provided by a third party may be
terminated with or without notice.
Internet radio services may not be available in some areas.
Using Internet Radio
Using Slacker Personal Radio
1
If you do not have an account, create one on
the Slacker website (www.slacker.com) with
your computer.
If you already have a Slacker account, select
“Sign in to your account” and then press
ENTER.
The keyboard screen appears. You can enter
information from the remote control or the keys
on the main unit.
2
If there are no mistakes in the information you
have entered, use q/w/e/r to select “OK”
then press ENTER.
An account information confirmation screen
appears.
3
If you do not have an account, select “Access
without Sign In” and press ENTER to use a
restricted version of the service.
Note that use will be restricted.
Tip
• If you want to use multiple user accounts, see “Using
Multiple Accounts” (➔ page 1). Login can be made
from the “Users” screen.
4
Use q/w to select a menu item and then press
ENTER.
To sign out, use q/w to select “Sign out” from
this screen and then press ENTER.
5
Use q/w to select a station and then press
ENTER or 1 to start playback from the
station.
The playback screen appears.
6
You can control the tracks with the buttons on
the remote control.
Enabled buttons: 1, 3, 2, 6
■ Menu Items
Rate Song as Favorite:
Stores information to server, making it more likely
that the song will be played again.
Ban Song:
Stores information to server, making it less likely
that the song will be played again.
Ban Artist:
Stores information to server, making it less likely
that the songs from this artist will be played
again.
Mark Favorite:
Adds the currently playing station to your
favorites.
Unmark Favorite:
Deletes the currently playing station from your
favorites.
Add song to Library:
Adds the currently playing track to your library.
Delete song from Library:
Deletes the currently playing track from your
library.
Add to My Favorites:
Adds a station or song to My Favorites list.
En-6
Using Internet Radio
Using MP3tunes
Listen to your music collection on your home stereo in
complete digital fidelity without a personal computer
plus safely backup all your songs. Here’s how:
Playing Contents on the AV Receiver
Tip
• Before proceeding, you need to select the MP3tunes
service as described in “Common Procedures in Internet
Radio Menu” (➔ page 1).
The track at the top of the music list is automatically
played back.
5
Creating an Account on your Computer
1
From your computer, open a web browser and
go to: www.mp3tunes.com/signup
2
3
Create an account.
4
View, edit and listen to your files by clicking
on Player (www.mp3tunes.com/player).
1
Use q/w to select “Sign in to your account”,
and then press ENTER.
2
Enter the e-mail address and password you
used when creating your account, select “OK”
and press ENTER.
The keyboard screen appears. You can enter
your user name and password from the remote
controller or the buttons on the AV receiver.
Click the Upload link
(www.mp3tunes.com/upload) to add files to
your Locker.
3
If there are no mistakes in the information you
have entered, select “OK” and press ENTER.
An account information confirmation screen
appears.
Tip
• If you want to use multiple user accounts, see “Using
Multiple Accounts” (➔ page 1). Login can be made
from the “Users” screen.
4
Use q/w to select the menu, then press
ENTER.
Music:
The place to find your Artists, Albums, and
Playlists.
Shuffle:
Starts playing a random selection of tracks from
your Locker.
Search:
Find a specific Album, Artist, or Song.
Account Info:
Your MP3tunes account information.
Sign Out:
Log out of your MP3tunes account.
En-7
Use q/w to select a track and press ENTER or
1 to start playback.
A playback screen appears.
You can control the tracks with the buttons on the
remote control.
Enabled buttons: 1, 3, 2, 7, 6
■ Menu Items
Go to Menu:
Displays additional menu options.
6
You can view or change your MP3tunes
account settings by going to
www.mp3tunes.com/account.
Utilisation d’une webradio
Utilisation d’une
webradio
Procédures courantes dans le menu de
webradio
Remarque
• Les services disponibles peuvent varier en fonction de la
région.
• Certain services réseau ou contenus disponible via cet
appareil peuvent être inaccessibles au cas où le prestataire
de services terminerait son service.
1
2
Appuyez sur NET.
Une liste des services réseau s’affiche, et le
témoin NET s’allume. S’il clignote, vérifiez que le
câble Ethernet est fermement branché sur
l’ampli-tuner AV.
Sélectionnez le service désiré et appuyez sur
ENTER.
La page principale du service sélectionné
s’affiche.
Utilisation de plusieurs comptes
L’ampli-tuner AV prend en charge plusieurs comptes
utilisateur, ce qui signifie que vous pouvez librement
commuter entre plusieurs connexions. Après avoir
enregistré des comptes utilisateur, l’identification est
réalisée à partir de l’écran « Users ».
1
Appuyez sur MENU lorsque l’écran Users est
affiché.
Les éléments de menu suivants s’affichent :
Add new user :
Remove this user :
Vous pouvez soit stocker un nouveau compte
utilisateur, soit en supprimer un existant.
Pandora® internet Radio
–Pour commencer
(États-Unis uniquement).......................... 2
Utilisation de Rhapsody
(Etats-Unis uniquement).......................... 3
Utilisation de SiriusXM Internet Radio
(Amérique du Nord uniquement) ............ 4
Utilisation de la webradio Last.fm................ 5
Conseil
• Certains des services ne permettent pas l’utilisation de
plusieurs comptes utilisateur.
• Vous pouvez stocker jusqu’à 10 comptes utilisateur.
• Pour commuter entre les comptes, vous devez d’abord
vous déconnecter du compte actuel, puis vous reconnectez
depuis l’écran « Users ».
Fr-1
Utilisation de Slacker Personal Radio ......... 6
Utilisation d’une webradio
Pandora® internet Radio
–Pour commencer (États-Unis
uniquement)
Pandora est un service de radio en ligne libre et
personnalisé vous permettant de lire la musique que
vous connaissez et de découvrir celle que vous
aimez.
1
Utilisez q/w pour sélectionner « I have a
Pandora Account » ou « I’m new to Pandora »,
puis appuyez sur ENTER.
Si vous ne connaissez pas Pandora sélectionnez
« I’m new to Pandora ». Un code d’activation
apparaîtra sur l’écran de votre téléviseur. Notez
ce code. Utilisez un ordinateur branché sur
Internet et connectez le navigateur à
www.pandora.com/onkyo
Saisissez votre code d’activation puis suivez les
instructions pour créer votre compte Pandora et
vos stations webradio Pandora personnalisées.
Lorsque vous y êtes invités, vous pouvez créer
vos stations en saisissant vos pistes et vos
artistes préférés. Après la création de votre
compte et de vos stations, vous pouvez retourner
à votre récepteur Onkyo et appuyez sur entrée
pour écouter votre webradio Pandora
personnalisée.
Si vous disposez d’un compte Pandora, vous
pouvez ajouter votre compte Pandora à votre
récepteur Onkyo en sélectionnant « I have a
Pandora Account » et y accéder en entrant
votre adresse e-mail et votre mot de passe.
2
Pour lire une station, utilisez q/w pour
sélectionner la station dans votre liste de
stations, puis appuyez sur ENTER.
La lecture débute et l’écran de lecture s’affiche.
Create a New Station :
Saisissez le nom d’une piste, d’un artiste ou d’un
genre et Pandora créera une station radio unique
pour vous en fonction des qualités musicales de
la piste, de l’artiste ou du genre choisi.
■ Eléments du menu
I like this track :
Acceptez la piste et Pandora lira d’autres
musiques similaires.
I don’t like this track :
Rejetez la piste et Pandora éliminera cette piste
de la station écoutée.
Why is this track playing? :
Découvrez certains des attributs musicaux que
Pandora utilise pour créer vos stations radio
personnelles.
I’m tired of this track :
Si vous en avez assez d’une piste, vous pouvez
mettre la piste « au repos » et Pandora ne la lira
plus pendant un mois.
Create station from this artist :
Permet de créer une station radio à partir de cet
artiste.
Conseil
• Si vous souhaitez utiliser plusieurs comptes
utilisateur, consultez « Utilisation de plusieurs
comptes » (➔ page 1). L’identification peut être
réalisée à partir de l’écran « Users ».
Fr-2
Delete this station :
Ceci supprimera de façon permanente la station
de votre compte Pandora. Au cas où vous
décideriez de récréer la station avec les mêmes
pistes ou les mêmes artistes, tous vos
acceptations/rejets précédents seront perdus.
Create station from this track :
Permet de créer une station radio à partir de
cette piste.
Rename this station :
Vous permet de renommer la station radio
actuelle.
Bookmark this artist :
Pandora marquera votre artiste préféré pour
votre profil sur www.pandora.com.
Bookmark this track :
Pandora marquera la piste en cours et vous
permettra de toutes les acheter sur Amazon ou
iTunes en une étape !
Add to My Favorites :
Permet d’ajouter une station à la liste My
Favorites.
PANDORA, le logo PANDORA, et l’habillage
commercial Pandora sont des marques
commerciales ou des marques déposées de la
société Pandora Media, Inc. Utilisées avec
autorisation.
Utilisation d’une webradio
Utilisation de Rhapsody (Etats-Unis
uniquement)
1
Utilisez q/w pour sélectionner « Sign in to your
account », puis appuyez sur ENTER.
Vous devez posséder un compte pour utiliser
Rhapsody. Si vous ne disposez pas encore d’un
compte, vous pouvez en créer un à partir de
www.rhapsody.com/onkyo
Si vous possédez déjà un compte Rhapsody,
sélectionnez « Sign in to your account », puis
appuyez sur ENTER.
Saisissez votre nom utilisateur (en général votre
adresse électronique) et votre mot de passe dans
l’écran clavier suivant ou dans Configuration
Web.
■ Utilisation de l’écran clavier
1. Utilisez q/w/e/r et ENTER pour saisir votre
nom d’utilisateur et votre mot de passe.
2. Sélectionnez « OK ».
3. Appuyez sur ENTER. L’écran « Confirm
your entries » s’affiche.
4. Appuyez sur ENTER.
2
Utilisez q/w pour sélectionner le menu, puis
appuyez sur ENTER.
Search :
Vous pouvez rechercher des morceaux par
artiste, par album ou par piste.
Music Guide :
Vous pouvez lire des pistes à partir des
genres,des meilleurs artistes, des meilleurs
albums, des meilleures pistes, des nouveautés et
des sélections du personnel.
Rhapsody Channels :
Écoutez les canaux de radio programmée par les
meilleurs éditeurs de Rhapsody.
Playlists :
Permet de jouer vos listes de lecture
personnelles.
My Library :
Marquez vos albums et vos pistes personnelles
dans le catalogue de Rhapsody à l’aide de My
Library.
Account Info :
Vérifiez les informations de votre compte.
Sign Out :
Déconnectez-vous de votre compte Rhapsody.
Conseil
• Si vous souhaitez utiliser plusieurs comptes
utilisateur, consultez « Utilisation de plusieurs
comptes » (➔ page 1). L’identification peut être
réalisée à partir de l’écran « Users ».
3
Utilisez q/w pour sélectionner un canal, puis
appuyez sur ENTER ou 1 pour démarrer la
lecture.
La lecture débute et l’écran de lecture s’affiche.
Vous pouvez contrôlez les pistes avec les
touches sur la télécommande.
Boutons activés : 1, 3, 2, 5, 4, 7,
6, RANDOM, REPEAT
Remarque
• Sur les canaux Rhapsody, certaines touches ne
fonctionnent pas.
■ Eléments du menu
Add track to My Library :
Marquez les pistes en cours de lecture.
Add album to My Library :
Marquez les albums en cours de lecture.
Add playlist to My Library :
Marquez les listes de lecture en cours de lecture.
Add channel to My Channels :
Marquez les canaux de radio Rhapsody en cours
de lecture.
Add to My Favorites :
Permet d’ajouter une piste, un canal ou une liste
de lecture à la liste My Favorites.
Conseil
• Vous pouvez supprimer des pistes, des albums et des
canaux Rhapsody marqués de My Library.
Fr-3
Utilisation d’une webradio
Utilisation de SiriusXM Internet Radio
(Amérique du Nord uniquement)
1
Votre ampli-tuner AV Onkyo comprend un essai
gratuit de SiriusXM Internet Radio. L’écran « Account
Info » affiche le nombre de jours restants dans votre
essai. Une fois la période d’essai expirée, si vous
souhaitez continuer à écouter le service, vous devez
vous abonner. Pour vous inscrire, accédez à
l’adresse
www.siriusxm.com/internetradio à l’aide de votre
ordinateur.
Utilisez q/w pour sélectionner « Sign In », puis
appuyez sur ENTER.
Si vous possédez déjà un compte SIRIUS, vous
pouvez y accéder en sélectionnant « Sign In ».
Saisissez votre nom utilisateur et votre mot de
passe dans l’écran clavier suivant ou dans
Configuration Web. Si vous ne connaissez pas
votre nom d’utilisateur ou votre mot de passe,
appelez Sirius XM au (888) 539-7474 pour
obtenir une assistance.
Conseil
• Si vous souhaitez utiliser plusieurs comptes
utilisateur, consultez « Utilisation de plusieurs
comptes » (➔ page 1). L’identification peut être
réalisée à partir de l’écran « Users ».
Lorsque vous vous inscrivez, vous devez fournir un
nom est un mot de passe utilisateur qui doivent être
saisis dans l’ampli-tuner AV.
■ Utilisation de l’écran clavier
1. Utilisez q/w/e/r et ENTER pour saisir votre
nom d’utilisateur et votre mot de passe.
2. Sélectionnez « OK ».
3. Appuyez sur ENTER. L’écran « Confirm
your entries » s’affiche.
4. Appuyez sur ENTER.
« Please wait... » s’affiche, puis l’écran
« SiriusXM Internet Radio » affiche la catégorie
que vous pouvez sélectionner.
Pour utiliser SiriusXM Internet Radio, l’ampli-tuner AV
doit être connecté à Internet. Suivez les étapes cidessous à l’aide de la télécommande :
2
Utilisez q/w pour sélectionner la catégorie,
puis appuyez sur ENTER.
L’écran de la liste des canaux de la catégorie
sélectionnée s’affiche.
Fr-4
3
Utilisez q/w pour sélectionner le canal de
votre choix, puis appuyez sur ENTER.
L’écran de lecture du canal sélectionné s’affiche
et vous pouvez écouter SiriusXM Internet Radio.
Vous pouvez contrôlez les pistes avec les
touches sur la télécommande.
Boutons activés : 2, 3, 7, 6
■ Eléments du menu
Add to My Favorites :
Permet d’ajouter un canal à la liste My Favorites.
Les abonnements SiriusXM Internet Radio sont
vendus séparément et sont subordonnés par les
conditions Sirius (voir www.sirius.com). Assurez-vous
de lire cet accord avant d’acquérir votre abonnement.
Sirius, XM et tous les logos et marques afférents sont
des marques déposées de Sirius XM Radio Inc. et de
ses filiales. Tous droits réservés.
Utilisation d’une webradio
Utilisation de la webradio Last.fm
1
Last.fm un service de musique qui apprend ce que
vous aimez…
Votre nouvel ampli-tuner AV Onkyo est très intelligent.
Si vous avez un compte Last.fm gratuit, il garde une
trace de toutes les chansons que vous avez juste
jouées. Quand vous vous rendez sur le site Web de
Last.fm, vous pouvez voir les graphiques personnels
de la musique que vous avez appréciée, les partagez
avec vos amis et également voir ce qu’ils aiment.
■ Utilisation de l’écran clavier
1. Utilisez q/w/e/r et le bouton ENTER pour
saisir votre nom d’utilisateur et votre mot de
passe.
2. Sélectionnez « OK ».
3. Appuyez sur ENTER. L’écran « Confirm
your entries » s’affiche.
4. Appuyez sur ENTER.
« Please wait... » apparait puis l’écran « Last.fm
Internet Radio » apparait.
Avec des milliers de biographies, de revues et un
choix infini de stations de radio personnalisées et
sans pub, Last.fm est excellent moyen de découvrir
de la musique. Créez aujourd’hui votre compte
Last.fm gratuit sur www.last.fm/join
Inscrivez-vous et vous pourrez apprécier le meilleur
de la radio sans pub Last.fm sur votre ampli-tuner AV
Onkyo sans ordinateur !
Recommended Radio :
Découvrez les recommandations personnalisées
futées qui changent en même temps que vos goûts.
Artist Radio :
Sélectionnez n’importe quel artiste et nous vous
jouerons une station entière de musique inspirée par
votre choix.
My Library :
Reposez-vous de retour et appréciez les sélections à
partir de toute la musique que vous avez entendue
depuis que vous avez joint Last.fm.
Tag Radio :
Funk polonaise ? Death pop ? Pensez à un style et
nous vous divertirons avec pendant des heures.
Commencez votre essai gratuit immédiatement à la
création votre compte et découvrez par vous-même
ce que cela fait d’avoir la musique du monde au bouts
des doigts. Les derniers prix et les informations
complètes sont disponibles sur www.last.fm/subscribe
Profile :
Vous pouvez lire des pistes de « Recently
Listened Tracks », « Library » et
« Neighbours ».
Account Info :
Vérifiez les informations de votre compte.
Sign Out :
Pour vous déconnecter de votre compte.
Utilisez q/w pour sélectionner « Sign in to
your account », puis appuyez sur ENTER.
Vous possédez déjà un compte Last.fm, vous
pouvez vous y connecter pour sélectionner
« Sign in to your account ». Saisissez votre
nom utilisateur et votre mot de passe dans
l’écran clavier suivant.
3
■ Eléments du menu
I Love this track :
L’information de la piste est sauvegardée dans le
serveur Last.fm, et la fréquence de lecture
augmente.
Ban this track :
L’information de la piste est sauvegardée dans le
serveur Last.fm, et la fréquence de lecture
diminue.
Add to My Favorites :
Permet d’ajouter une station à la liste My
Favorites.
Conseil
• Si vous souhaitez utiliser plusieurs comptes
utilisateur, consultez « Utilisation de plusieurs
comptes » (➔ page 1). L’identification peut être
réalisée à partir de l’écran « Users ».
2
Utilisez q/w pour sélectionner un menu puis
appuyez sur ENTER.
Search Station :
Vous pouvez rechercher une station par artiste,
par tag ou par nom d’utilisateur.
Top Artists Station :
Vous pouvez lire des pistes des artistes les mieux
évalués.
Top Tags Station :
Vous pouvez lire des pistes des tags les mieux
évalués.
Personal Station :
Vous pouvez lire des pistes de votre station
personnalisée (« Your Library », « Your
Neighbourhood » et « Your
Recommendations »).
Fr-5
Utilisez q/w pour sélectionner une station, puis
appuyez sur ENTER ou 1 pour démarrer la
lecture.
La lecture débute et l’écran de lecture s’affiche.
■ Utilisation du contrôle Scrobbling
Utilisez q/w pour sélectionner « Enable », puis
appuyez sur ENTER.
*
Les services de webradio fournis par un tiers peuvent être
résiliés avec ou sans préavis.
Les services de webradio peuvent ne pas être accessibles
dans certaines zones.
Utilisation d’une webradio
Utilisation de Slacker Personal Radio
1
Si vous ne possédez pas de compte, créez-en
un à partir du site Web de Slacker
(www.slacker.com) à l’aide de votre
ordinateur.
Si vous possédez déjà un compte Slacker,
sélectionnez « Sign in to your account », puis
appuyez sur ENTER.
L’écran clavier s’affiche. Pouvez saisir des
informations à partir de la télécommande ou des
touches sur l’appareil principal.
2
Si les informations que vous avez saisies ne
comportent pas d’erreur, utilisezq/w/e/r
pour sélectionner « OK », puis appuyez sur
ENTER.
L’écran de confirmation des informations du
compte s’affiche.
3
Si vous ne possédez pas de compte,
sélectionnez « Access without Sign In », puis
appuyez sur ENTER pour utiliser une version
restreinte du service.
Veuillez noter que l’utilisation est restreinte.
Conseil
• Si vous souhaitez utiliser plusieurs comptes
utilisateur, consultez « Utilisation de plusieurs
comptes » (➔ page 1). L’identification peut être
réalisée à partir de l’écran « Users ».
4
Utilisez q/w pour sélectionner un élément du
menu, puis appuyez sur ENTER.
Pour vous déconnecter, utilisez q/w pour
sélectionner « Sign out » depuis cet écran, puis
appuyez sur ENTER.
5
Utilisez q/w pour sélectionner une station,
puis appuyez sur ENTER ou 1 pour démarrer
la lecture depuis cette station.
L’écran de lecture apparaît.
6
Vous pouvez contrôlez les pistes avec les
touches sur la télécommande.
Boutons activés : 1, 3, 2, 6
■ Eléments du menu
Rate Song as Favorite :
Permet de stocker des informations sur le
serveur, et d’augmenter la probabilité que le
morceau soit lu de nouveau.
Ban Song :
Permet de stocker des informations sur le
serveur, et de diminuer la probabilité que le
morceau soit lu de nouveau.
Ban Artist :
Permet de stocker des informations sur le
serveur, et de diminuer la probabilité que les
morceaux de cet artiste soient lus de nouveau.
Mark Favorite :
Permet d’ajouter la station en cours de lecture à
vos favoris.
Unmark Favorite :
Permet de supprimer la station en cours de
lecture de vos favoris.
Add song to Library :
Permet d’ajouter la piste en cours de lecture à
votre bibliothèque.
Delete song from Library :
Permet de supprimer la piste en cours de lecture
de votre bibliothèque.
Add to My Favorites :
Permet d’ajouter une station ou un morceau à la
liste My Favorites.
Fr-6
Uso de Internet Radio
Uso de Internet Radio
Procedimientos comunes en el menú
Internet Radio
Nota
• Los servicios disponibles pueden variar de una región a
otra.
• Es posible que determinados servicios de red o contenidos
disponibles a través de este dispositivo no sean accesibles
si el proveedor del servicio da por finalizado el servicio.
1
2
Pulse NET.
Aparecerá una lista de los servicios de red y se
iluminará el indicador NET. Si parpadea,
verifique que el cable Ethernet esté firmemente
conectado al receptor de AV.
Seleccione el servicio deseado y pulse
ENTER.
Aparecerá la página principal del servicio
seleccionado.
Uso de múltiples cuentas
El receptor de AV permite múltiples cuentas de
usuario, lo que quiere decir que se puede cambiar
libremente entre varios usuarios. Después de
registrar las cuentas de usuario, el acceso se realiza
desde la pantalla “Users”.
1
Pulse MENU cuando aparezca la pantalla de
usuarios.
Aparecerán los siguientes elementos del menú:
Add new user:
Remove this user:
Puede guardar una nueva cuenta de usuario o
borrar una existente.
Pandora® Internet Radio
–Primeros pasos (solo EE.UU.)............... 2
Uso de Rhapsody (sólo EE.UU.)................... 3
Uso de SiriusXM Internet Radio
(solo Norteamérica).................................. 4
Uso de Last.fm Internet Radio ...................... 5
Consejo
• Algunos de los servicios no permiten el uso de múltiples
cuentas de usuario.
• Puede guardar hasta 10 cuentas de usuario.
• Para cambiar entre cuentas debe antes cerrar sesión en la
cuenta actual y acceder de nuevo en la pantalla “Users”.
Es-1
Uso de Slacker Personal Radio .................... 6
Uso de Internet Radio
Pandora® Internet Radio
–Primeros pasos (solo EE.UU.)
Pandora es un servicio de radio por Internet gratuito y
personalizado que reproduce la música que usted
conoce y le ayudará a descubrir música que le
encantará.
1
Utilice q/w para seleccionar “I have a Pandora
Account” o “I’m new to Pandora” y luego
pulse ENTER.
Si no conoce Pandora seleccione “I’m new to
Pandora”. Verá un código de activación en la
pantalla del televisor. Tome nota de este código.
Vaya a un ordenador conectado a Internet y dirija
el navegador a www.pandora.com/onkyo
Introduzca su código de activación y siga las
instrucciones para crear su cuenta de Pandora y
sus emisoras de radio por Internet
personalizadas de Pandora. Puede crear sus
propias emisoras introduciendo sus temas y
artistas favoritos cuando aparezca la solicitud
correspondiente. Una vez creada su cuenta y sus
emisoras, puede regresar al receptor Onkyo y
pulsar Enter para empezar a escuchar su radio
por Internet personalizada de Pandora.
Si ya dispone de una cuenta de Pandora, puede
añadirla al receptor Onkyo seleccionando “I have
a Pandora Account” e iniciando la sesión con su
dirección de correo electrónico y contraseña.
2
Utilice q/w para seleccionar la emisora en la
lista de emisoras y luego pulse ENTER.
Se inicia la reproducción y aparece la pantalla de
reproducción.
Create a New Station:
Introduzca el nombre de un tema, artista o
género; Pandora creará una emisora de radio
exclusiva para usted basada en las cualidades
musicales de ese tema, de ese artista o de ese
género.
■ Elementos del menú
I like this track:
Si aprueba (pulgar arriba) un tema, Pandora
reproducirá más música parecida.
I don’t like this track:
Si no aprueba (pulgar abajo) el tema, Pandora
eliminará dicho tema de la emisora actual.
Why is this track playing?:
Descubra algunos de los atributos musicales que
Pandora utiliza para crear sus emisoras de radio
personalizadas.
I’m tired of this track:
Si se cansa de un tema, puede “silenciarlo” de
modo que Pandora no lo reproduzca durante un
mes.
Create station from this artist:
Crea una emisora de radio a partir de este
artista.
Consejo
• Si desea utilizar múltiples cuentas de usuario,
consulte “Uso de múltiples cuentas” (➔ página 1). Se
puede iniciar sesión desde la pantalla “Users”.
Es-2
Delete this station:
Esto eliminará de forma permanente una
emisora de su cuenta de Pandora. Toda la
información sobre sus aprobaciones/
desaprobaciones se perderá si quiere volver a
crear la emisora con el mismo tema o artista.
Create station from this track:
Crea una emisora de radio a partir de este tema.
Rename this station:
Le permite renombrar la emisora de radio actual.
Bookmark this artist:
Pandora marcará su artista favorito para su perfil
en www.pandora.com.
Bookmark this track:
Pandora marcará el tema actual y le permitirá
comprarlos todos en Amazon o iTunes ¡con un
solo paso!
Add to My Favorites:
Añade una emisora a la lista Mis favoritos.
PANDORA, el logotipo de PANDORA logo, y la
imagen corporativa de Pandora son marcas
comerciales o marcas comerciales registradas de
Pandora Media, Inc. Uso con permiso.
Uso de Internet Radio
Uso de Rhapsody (sólo EE.UU.)
1
Utilice q/w para seleccionar “Sign in to your
account” y luego pulse ENTER.
Para utilizar Rhapsody, necesitará una cuenta. Si
todavía no tiene una, puede crear una nueva en
www.rhapsody.com/onkyo
Si ya tiene una cuenta Rhapsody, seleccione
“Sign in to your account” y pulse ENTER.
Escriba su nombre de usuario (normalmente el
correo electrónico) y contraseña en la pantalla de
teclado que aparece a continuación o en la
configuración web.
■ Utilización de la pantalla de teclado
1. Utilice q/w/e/r y ENTER para introducir su
nombre de usuario y su contraseña.
2. Seleccione “OK”.
3. Pulse ENTER. Aparecerá la pantalla
“Confirm your entries”.
4. Pulse ENTER.
Consejo
2
Utilice q/w para seleccionar el menú y luego
pulse ENTER.
Search:
Puede buscar música por artista, álbum o
canción.
Music Guide:
Puede reproducir canciones por géneros, artistas
principales, álbumes principales o canciones
principales, novedades, selección del sitio.
Rhapsody Channels:
Escuche las emisoras de radio programadas por
los principales redactores de Rhapsody.
Playlists:
Reproduzca sus listas personales.
My Library:
Marque sus álbumes y canciones preferidas en
el catálogo de Rhapsody, usando Mi biblioteca.
Account Info:
Confirme los datos de su cuenta.
Sign Out:
Salga de su cuenta Rhapsody.
• Si desea utilizar múltiples cuentas de usuario,
consulte “Uso de múltiples cuentas” (➔ página 1). Se
puede iniciar sesión desde la pantalla “Users”.
3
Utilice q/w para seleccionar una emisora y
luego pulse ENTER o 1 para iniciar la
reproducción.
Se inicia la reproducción y aparece la pantalla de
reproducción.
Puede controlar las pistas con los botones del
mando a distancia.
Botones activados: 1, 3, 2, 5, 4, 7,
6, RANDOM, REPEAT
Nota
• En Rhapsody Channels, algunos de los botones no
funcionan.
■ Elementos del menú
Add track to My Library:
Marca las canciones que se están reproduciendo
actualmente.
Add album to My Library:
Marca los álbumes que se están reproduciendo
actualmente.
Add playlist to My Library:
Marca las listas de reproducción que se están
reproduciendo actualmente.
Add channel to My Channels:
Marca las emisoras de Rhapsody que se están
reproduciendo actualmente.
Add to My Favorites:
Añade una canción, emisora o lista de
reproducción a la lista Mis favoritos.
Consejo
• Puede eliminar las canciones, los álbumes y las
emisoras de Rhapsody marcados de Mi biblioteca.
Es-3
Uso de Internet Radio
Uso de SiriusXM Internet Radio (solo
Norteamérica)
1
Su receptor de AV Onkyo incluye una prueba gratuita
de SiriusXM Internet Radio. La pantalla “Account
Info” muestra los días que quedan de la prueba. Una
vez que termine el periodo de prueba, si desea seguir
escuchando este servicio, deberá contratarlo. para
suscribirse vaya a
www.siriusxm.com/internetradio con su
ordenador.
Utilice q/w para seleccionar “Sign In”, y luego
pulse ENTER.
Si ya tiene una cuenta SIRIUS, puede acceder
seleccionando “Sign In”. Escriba su nombre de
usuario y contraseña en la pantalla de teclado
que aparece a continuación o en la configuración
web. Si no sabe su nombre de usuario o la
contraseña, llame a Sirius XM al número (888)
539-7474 para solicitar asistencia.
Consejo
• Si desea utilizar múltiples cuentas de usuario,
consulte “Uso de múltiples cuentas” (➔ página 1). Se
puede iniciar sesión desde la pantalla “Users”.
Cuando se suscriba, recibirá un nombre de usuario y
una contraseña que deberá introducir en el receptor
de AV.
■ Utilización de la pantalla de teclado
1. Utilice q/w/e/r y ENTER para introducir su
nombre de usuario y su contraseña.
2. Seleccione “OK”.
3. Pulse ENTER. Aparecerá la pantalla
“Confirm your entries”.
4. Pulse ENTER.
Aparecerá “Please wait...” y después la pantalla
“SiriusXM Internet Radio”, que muestra la
categoría disponible para la selección.
Para poder utilizar SiriusXM Internet Radio, el
receptor de AV debe estar conectado a internet. Para
usar el mando a distancia, siga este procedimiento:
2
Utilice q/w para seleccionar la categoría y
luego pulse ENTER.
Aparece una pantalla con una lista de emisoras
de la categoría seleccionada.
Es-4
3
Utilice q/w para seleccionar la emisora
deseada y luego pulse ENTER.
Aparecerá la pantalla de reproducción de la
emisora seleccionada y ahora usted podrá
escuchar SiriusXM Internet Radio.
Puede controlar las pistas con los botones del
mando a distancia.
Botones activados: 2, 3, 7, 6
■ Elementos del menú
Add to My Favorites:
Añade una emisora a la lista Mis favoritos.
Las suscripciones a SiriusXM Internet Radio se
venden por separado y se rigen por las condiciones
de Sirius (consulte www.sirius.com). Lea
atentamente este acuerdo antes de comprar la
suscripción. Sirius, XM y todas las marcas y logotipos
relacionados son marcas comerciales de Sirius XM
Radio Inc. y sus filiales. Todos los derechos
reservados.
Uso de Internet Radio
Uso de Last.fm Internet Radio
1
Last.fm es un servicio musical que sabe lo que le
gusta...
Su nuevo receptor de AV Onkyo es muy inteligente.
Si tiene una cuenta gratuita de Last.fm, hará un
seguimiento de todas las canciones que acaba de
escuchar. Cuando visite el sitio web de Last.fm,
podrá ver listas personales de la música que ha
disfrutado, compartirlas con sus amigos y también
ver lo que les gusta a ellos.
■ Utilización de la pantalla de teclado
1. Utilice q/w/e/r y ENTER para introducir su
nombre de usuario y su contraseña.
2. Seleccione “OK”.
3. Pulse ENTER. Aparecerá la pantalla
“Confirm your entries”.
4. Pulse ENTER.
Aparecerá “Please wait...” y después la pantalla
“Last.fm Internet Radio”.
Con sus miles de biografías, críticas y una infinita
variedad de emisoras de radio personalizadas y sin
publicidad, Last.fm es una forma excelente de
descubrir música. Cree hoy mismo una cuenta
gratuita de Last.fm en www.last.fm/join
Si se suscribe podrá disfrutar de lo mejor de Last.fm
Radio sin anuncios en su receptor de AV Onkyo sin
necesidad de un ordenador.
Recommended Radio:
Descubra nuestras interesantes recomendaciones
personalizadas que se adaptan a sus gustos en cada
momento.
Artist Radio:
Escoja cualquier artista y podrá escuchar una
emisora de radio inspirada exclusivamente en su
elección.
My Library:
Relájese y disfrute de selecciones de toda la música
que ha escuchado desde que se registró en Last.fm.
Tag Radio:
¿Polish funk? ¿Death pop? Piense en un estilo y
podrá escucharlo durante horas.
Profile:
Puede reproducir pistas de “Recently Listened
Tracks”, “Library” y “Neighbours”.
Account Info:
Confirme los datos de su cuenta.
Sign Out:
Se desconecta de su cuenta.
Utilice q/w para seleccionar “Sign in to your
account”, y luego pulse ENTER.
Si ya tiene una cuenta de Last.fm, puede
acceder a ella para seleccionar “Sign in to your
account”. Introduzca su nombre de usuario y
contraseña en la siguiente pantalla de teclado.
3
■ Elementos del menú
I Love this track:
Se guarda la información sobre la canción en el
servidor de Last.fm y aumenta la frecuencia con
la que se reproduce.
Ban this track:
Se guarda la información sobre la canción en el
servidor de Last.fm y se reduce la frecuencia con
la que se reproduce.
Add to My Favorites:
Añade una emisora a la lista Mis favoritos.
Consejo
• Si desea utilizar múltiples cuentas de usuario,
consulte “Uso de múltiples cuentas” (➔ página 1). Se
puede iniciar sesión desde la pantalla “Users”.
2
Utilice q/w para seleccionar un menú y luego
pulse ENTER.
Search Station:
Puede buscar emisoras por artista, etiquetas o
nombre de usuario.
Top Artists Station:
Puede reproducir canciones de los artistas mejor
clasificados.
Top Tags Station:
Puede reproducir canciones con las etiquetas
mejor clasificadas.
Personal Station:
Puede reproducir pistas de una emisora
personalizada (“Your Library”, “Your
Neighbourhood” y “Your Recommendations”).
Pruébelo gratis ahora mismo. Cree una cuenta y verá
por sí mismo lo que significa tener toda la música del
mundo al alcance de sus oídos. Puede consultar los
precios actualizados y toda la información que desee
en www.last.fm/subscribe
Es-5
Utilice q/w para seleccionar una emisora y
luego pulse ENTER o 1 para iniciar la
reproducción.
Se inicia la reproducción y aparece la pantalla de
reproducción.
■ Uso del control de scrobbling
Utilice q/w para seleccionar “Enable”, y luego pulse
ENTER.
*
Los servicios de radio por Internet suministrados por
terceros pueden cancelarse con o sin aviso previo.
Es posible que los servicios de radio por Internet no estén
disponibles en algunas zonas.
Uso de Internet Radio
Uso de Slacker Personal Radio
1
Si no tiene una cuenta, cree una en el sitio web
de Slacker (www.slacker.com) con su
ordenador.
Si ya tiene una cuenta de Slacker, seleccione
“Sign in to your account” y pulse ENTER.
Aparecerá la pantalla de teclado. Puede
introducir información desde el mando a
distancia o desde el teclado de la unidad
principal.
2
Si no hay errores en la información que ha
introducido, utilice q/w/e/r para seleccionar
“OK” y luego pulse ENTER.
Aparecerá una pantalla de confirmación de la
información de la cuenta.
3
Si no tiene una cuenta, seleccione “Access
without Sign In” y pulse ENTER para utilizar
una versión restringida del servicio.
Tenga en cuenta que el uso estará restringido.
Consejo
• Si desea utilizar múltiples cuentas de usuario,
consulte “Uso de múltiples cuentas” (➔ página 1). Se
puede iniciar sesión desde la pantalla “Users”.
4
Utilice q/w para seleccionar un menú y luego
pulse ENTER.
Para salir, utilice q/w para seleccionar “Sign out”
en esta pantalla y luego pulse ENTER.
5
Utilice q/w para seleccionar una emisora y
luego pulse ENTER o 1 para iniciar la
reproducción de la emisora.
Aparecerá la pantalla de reproducción.
6
Puede controlar las pistas con los botones del
mando a distancia.
Botones activados: 1, 3, 2, 6
■ Elementos del menú
Rate Song as Favorite:
Guarda información en el servidor, haciendo que
sea más probable que la canción se vuelva a
reproducir.
Ban Song:
Guarda información en el servidor, haciendo que
sea menos probable que la canción se vuelva a
reproducir.
Ban Artist:
Guarda información en el servidor, haciendo que
sea menos probable que las canciones de este
artista se vuelvan a reproducir.
Mark Favorite:
Añade la emisora que se está reproduciendo
actualmente a los favoritos.
Unmark Favorite:
Elimina la emisora que se está reproduciendo
actualmente de los favoritos.
Add song to Library:
Añade la canción que se está reproduciendo
actualmente a su biblioteca.
Delete song from Library:
Elimina la canción que se está reproduciendo
actualmente de la biblioteca.
Add to My Favorites:
Añade una emisora o canción a la lista Mis
favoritos.
Es-6
Y1212-1
SN 29401478IRUS
* 2 9 4 0 1 4 7 8 I R U S *
Using Internet Radio
Using Internet Radio
Common Procedures in Internet Radio
Menu
Note
• Available services may vary depending on the region.
• Certain network service or contents available through this
device may not be accessible in case the service provider
terminates its service.
1
2
Press NET.
A list of the network services appears, and the
NET indicator lights. If it flashes, verify that the
Ethernet cable is firmly connected to the AV
receiver.
Select the desired service and press ENTER.
The top page of the selected service appears.
Using Multiple Accounts
The AV receiver supports multiple user accounts,
which means you can freely switch between several
logins. After registering user accounts, login is
performed from the “Users” screen.
1
Press MENU while the Users screen is
displayed.
The following menu items appear:
Add new user:
Remove this user:
You can either store a new user account, or
delete an existing one.
Tip
• Some of the services don’t allow the use of multiple user
accounts.
• You can store up to 10 user accounts.
• To switch between accounts you must first log out from the
current account, and log in again on the “Users” screen.
En-1
Using Last.fm Internet Radio ........................ 2
Using Internet Radio
Using Last.fm Internet Radio
1
Last.fm is a music service that learns what you
love...
Your new Onkyo AV receiver is very clever. If you
have a free Last.fm account, it will keep track of all
the songs you’ve just played. When you visit the
Last.fm website, you can see personal charts of the
music you’ve enjoyed, share them with friends and
see what they like, too.
■ Using the keyboard screen
1. Use q/w/e/r and the ENTER to enter your
user name and password.
2. Select “OK”.
3. Press ENTER. The “Confirm your entries”
screen appears.
4. Press ENTER.
“Please wait...” appears and then “Last.fm
Internet Radio” screen appears.
With thousands of biographies, reviews and an
endless choice of personalised, ad-free radio
stations, Last.fm is a great way to discover music.
Pick up your free Last.fm account today at
www.last.fm/join
UK and Germany only:
Get a subscription and you can enjoy the best of adfree Last.fm Radio on your Onkyo AV receiver without
a computer!
Recommended Radio:
Discover smart personalised recommendations that
adapt as your tastes change.
Artist Radio:
Pick any artist and we’ll play you a whole station of
music inspired by your choice.
My Library:
Sit back and enjoy selections from all the music
you’ve heard since you joined Last.fm.
Tag Radio:
Polish funk? Death pop? Think of a style and we’ll
entertain you with it for hours.
Profile:
You can play tracks from “Recently Listened
Tracks”, “Library” and “Neighbours”.
Account Info:
Confirm your account information.
Sign Out:
It signs out from your account.
Use q/w to select “Sign in to your account”,
and then press ENTER.
If you have the existing Last.fm account, you can
sign in to your account to select “Sign in to your
account”. Enter your user name and password in
the next keyboard screen.
3
■ Menu Items
I Love this track:
Track information is saved in Last.fm server, and
playback frequency increases.
Ban this track:
Track information is saved in Last.fm server, and
playback frequency reduces.
Add to My Favorites:
Adds a station to My Favorites list.
Tip
• If you want to use multiple user accounts, see “Using
Multiple Accounts” (➔ page 1). Login can be made
from the “Users” screen.
2
Use q/w to select menu and then press
ENTER.
Search Station:
You can search station by Artist, Tag, or User
Name.
Top Artists Station:
You can play tracks of top-rated artists.
Top Tags Station:
You can play tracks of top-rated tags.
Personal Station:
You can play tracks from personalized station
(“Your Library”, “Your Neighbourhood” and
“Your Recommendations”).
Start your free trial straight away when you create
your account and see for yourself what it’s like to
have the world’s music at your fingertips. Latest
prices and full information are available at
www.last.fm/subscribe
En-2
Use q/w to select a station, and press ENTER
or 1 to start playback.
Playback starts and the playback screen
appears.
Enabled buttons: 1, 2, 6
■ Using scrobbling control
Use q/w to select “Enable”, and then press ENTER.
*
Internet radio services provided by a third party may be
terminated with or without notice.
Internet radio services may not be available in some areas.
Internetradio verwenden
Internetradio verwenden
Allgemeine Verfahren bei den
Internetradio-Menüs
Verwendung mehrerer Konten
Der AV-Receiver unterstützt mehrere Nutzerkonten,
was bedeutet, dass Sie frei zwischen mehreren
Logins umschalten können. Nach der Anmeldung der
Nutzerkonten wird das Login vom „Users“ Bildschirm
aus vorgenommen.
Anmerkung
• Die verfügbaren Dienste sind länderabhängig verschieden.
• Bestimmte Netzwerkdienste oder über dieses Gerät zur
Verfügung stehende Inhalte stehen eventuell nicht zur
Verfügung, falls der Service-Anbieter seine Dienstleistung
beendet.
1
2
Drücken Sie NET.
Es erscheint eine Liste der Netzwerkdienste und
die NET-Anzeige leuchtet. Wenn sie blinkt,
überprüfen Sie ob das Ethernet-Kabel fest im AVReceiver eingesteckt ist.
Wählen Sie den gewünschten Service aus und
drücken Sie ENTER.
Die oberste Seite des ausgewählten Services
erscheint.
1
Drücken Sie MENU während der Bildschirm
des Nutzers angezeigt wird.
Das folgende Menü erscheint:
Add new user:
Remove this user:
Sie können entweder ein neues Nutzerkonto
abspeichern oder ein bestehendes löschen.
Tipp
• Einige dieser Dienstleistungen lassen keine mehrfachen
Nutzerkonten zu.
• Sie können bis zu 10 Nutzerkonten speichern.
• Um zwischen den Konten umzuschalten, müssen Sie sich
zuerst aus Ihrem aktuellen Konto ausloggen und sich dann
wieder auf dem „Users“ Bildschirm einloggen.
De-1
Verwendung von Last.fm Internet Radio ..... 2
Internetradio verwenden
Verwendung von Last.fm Internet Radio
Last.fm ist ein Musikdienst, der sich Ihre
Lieblingsmusik merkt...
Ihr neuer Onkyo AV-Receiver ist äußerst clever. Wenn Sie
ein kostenloses Last.fm-Konto eingerichtet haben, werden
darin alle kürzlich abgespielten Titel gespeichert. Wenn Sie
die Last.fm-Website besuchen, können Sie Ihre
persönlichen Charts der von Ihnen abgespielten Musik
anzeigen; teilen Sie diese mit Freunden und sehen Sie
auch, welche Musik Ihre Freunde mögen.
können. Die aktuellen Nutzungspreise und umfassende
Infos sind unter www.last.fm/subscribe erhältlich
1
Nur für Großbritannien und Deutschland:
Holen Sie sich ein Abonnement und Sie können auch
ohne Computer die besten werbefreien Last.fmRadiosender auf Ihrem Onkyo AV-Receiver hören!
Recommended Radio:
Entdecken Sie smarte, persönlich angepasste
Empfehlungen, die sich mit Ihrem Musikgeschmack
verändern.
Artist Radio:
Wählen Sie einen beliebigen Interpreten und wir
spielen für Sie einen ganzen Radiosender mit durch
Ihre Wahl inspirierter Musik.
My Library:
Lehnen Sie sich zurück und erfreuen Sie sich an
einer Auswahl aller Musik, die Sie seit Ihrer
Mitgliedschaft bei Last.fm gehört haben.
Tag Radio:
Polish Funk? Death Pop? Denken Sie an einen
Musikstil und wir unterhalten Sie stundenlang damit.
Starten Sie Ihr kostenloses Probeabo direkt wenn Sie
Ihr Konto erstellen und finden Sie selbst heraus wie es
ist, jederzeit die Musik der ganzen Welt abrufen zu
Verwenden Sie q/w, um „Sign in to your
account“ auszuwählen und dann drücken Sie
ENTER.
Wenn Sie über einen bestehenden Last.fm Konto
verfügen, können Sie sich anmelden und „Sign
in to your account“ wählen. Geben Sie Ihre Ihre
Benutzernamen und das Kennwort in der
folgenden Tastaturanzeige ein.
■ Verwendung der Tastaturanzeige
1. Verwenden Sie q/w/e/r und den ENTER, um
Ihren Nutzernamen und Passwort einzugeben.
2. Wählen Sie „OK“.
3. Drücken Sie ENTER. Die Anzeige „Confirm
your entries“ erscheint.
4. Drücken Sie ENTER.
„Please wait...“ wird angezeigt und danach
erscheint die „Last.fm Internet Radio“-Anzeige.
Mit tausenden von Biografien, Rezensionen und einer
schier endlosen Auswahl an persönlich angepassten,
werbefreien Radiosendern ist Last.fm eine großartige
Gelegenheit, um Musik zu entdecken. Holen Sie sich
Ihr kostenloses Last.fm-Konto noch heute unter
www.last.fm/join
Personal Station:
Sie können Titel aus einem persönlich
angepassten Sender wiedergeben („Your
Library“, „Your Neighbourhood“ und „Your
Recommendations“).
Profile:
Sie können Titel aus „Recently Listened Tracks“,
„Library“ und „Neighbours“ wiedergeben.
Account Info:
Bestätigen Sie Ihre Kontoinformation.
Sign Out:
Zur Abmeldung aus Ihrem Konto.
3
Tipp
• Falls Sie mehrere Nutzerkonten verwenden möchten,
schlagen Sie bitte unter „Verwendung mehrerer
Konten“ nach (➔ Seite 1). Das Login kann vom
„Users“-Bildschirm aus erfolgen.
2
Verwenden Sie q/w, um das Menü
auszuwählen und dann drücken Sie ENTER.
Search Station:
Sie können einen Sender anhand Interpreten,
Tags oder Benutzernamen suchen.
Top Artists Station:
Sie können Titel der am besten bewerteten
Interpreten wiedergeben.
Top Tags Station:
Sie können Titel der am besten bewerteten Tags
wiedergeben.
Verwenden Sie q/w, um einen Sender
auszuwählen und dann drücken Sie ENTER
oder 1 , um die Wiedergabe zu starten.
Die Wiedergabe wird gestartet und die
Wiedergabeanzeige erscheint.
Aktivierte Tasten: 1, 2, 6
■ Menüsymbole
I Love this track:
Titel-Informationen werden auf dem Last.fmServer gespeichert und die Häufigkeit der
Wiedergabe wird erhöht.
Ban this track:
Titel-Informationen werden auf dem Last.fmServer gespeichert und die Häufigkeit der
Wiedergabe wird verringert.
Add to My Favorites:
Fügt einen Sender zu meiner My Favorites Liste hinzu.
■ Scrobbling-Steuerung verwenden
Verwenden Sie q/w, um „Enable“ auszuwählen und
dann drücken Sie ENTER.
*
Von Drittparteien zur Verfügung gestellte InternetradioDienste können unter Umständen ohne Vorankündigung
eingestellt werden.
In bestimmten Gebieten sind Internetradio-Dienste
eventuell nicht verfügbar.
Y1212-1
SN 29401479IREU
* 2 9 4 0 1 4 7 9 I R E U *
Remote Control Codes
Remote Control Codes
1
/
While holding down the REMOTE MODE button to which you want to assign a
code, press and hold down [DISPLAY] (about 3 seconds).
The REMOTE MODE button/Remote indicator lights.
On Integra products, button names are capitalized. For example, “Remote Mode”
button and “Display” button.
Notes:
• Remote control codes cannot be entered for [RECEIVER] and the multi zone button.
• Only TV remote control codes can be entered for [TV].
• Except for [RECEIVER], [TV], and the multi zone button, remote control codes from any
category can be assigned for the REMOTE MODE buttons. However, these buttons also work
as input selector buttons, so choose a REMOTE MODE button that corresponds with the input
to which you connect your component. For example, if you connect your CD player to the CD
input, choose [TV/CD] when entering its remote control code.
2
Within 30 seconds, use the number buttons to enter the 5-digit remote control
code.
The REMOTE MODE button/Remote indicator flashes twice.
If the remote control code is not entered successfully, the REMOTE MODE
button/Remote indicator will flash once slowly.
Notes:
• The flashing element of the remote controller will differ according to your AV receiver’s model.
• The remote controller is preconfigured with remote controller presets of different components.
By entering a code from the Remote Control Code list, you can activate the relevant preset for
that component.
• When there are multiple codes related to one manufacturer, try and enter them one-by-one until
it matches your component.
• Depending on the model and year of your component, compatibility is not guaranteed.
• With some models, the remote controller may not not work or its compatibility may be limited
to part of the component’s functionality.
• Besides, it is not possible to add new codes to the existing remote controller presets.
• Though the provided remote control codes are correct at the time of printing, they are subject to
change by the manufacturer.
1
Remote Control Codes
Codes de télécommande
Códigos de control remoto
1
1
Tout en maintenant enfoncé le bouton REMOTE MODE auquel vous souhaitez
associer un code, pressez et maintenez enfoncé le bouton [DISPLAY] (pendant
environ 3 secondes).
Le bouton REMOTE MODE/le témoin Remote s’allume.
Les noms de boutons sont en manjuscules sur les produits Integra. Par exemple, le
bouton « Remote Mode » et le bouton « Display ».
Remarques :
• Les codes de télécommande ne peuvent pas être entrés pour [RECEIVER] et le bouton multi
zone.
• Seul les code de télécommande de téléviseurs peuvent être entrés pour [TV].
• À l’exception de [RECEIVER], [TV] et du bouton multi zone, vous pouvez affecter des codes
de télécommande de n’importe quelle catégorie pour les boutons REMOTE MODE. Cependant,
ces boutons font également office de bouton de sélecteur d’entrée : par conséquent, choisissez
un bouton REMOTE MODE correspondant à l’entrée à laquelle vous souhaitez raccorder votre
appareil. Par exemple, si vous raccordez votre lecteur CD à l’entrée CD, choisissez [TV/CD]
lorsque vous saisissez le code de télécommande.
2
Manteniendo pulsado el botón REMOTE MODE para el cual desea introducir un
código, pulse y mantenga presionado el botón [DISPLAY] (aproximadamente 3
segundos).
Se iluminará el botón REMOTE MODE/indicador Remote.
En los productos Integra, los nombres de los botones aparecen con mayúsculas. Por
ejemplo, el botón “Remote Mode” y el botón “Display”.
Notas:
• No podrán introducirse códigos de mando a distancia para [RECEIVER] y el botón multizona.
• Únicamente podrán introducirse códigos de mando a distancia de televisor para el botón [TV].
• Con la excepción de [RECEIVER], [TV] y el botón multizona, se pueden asignar códigos de
mando a distancia de cualquier categoría a los botones de REMOTE MODE. No obstante, estos
botones también pueden funcionar como botones de selector de entrada; por tanto, seleccione
un botón REMOTE MODE que se corresponda con la entrada a la cual está conectado el
componente. Por ejemplo, si conecta un reproductor de CD a la entrada de CD, seleccione
[TV/CD] cuando introduzca su código de mando a distancia.
2
Vous disposez de 30 secondes pour saisir le code de télécommande à cinq chiffres
à l’aide des boutons numérotés.
Le bouton REMOTE MODE/le témoin Remote clignote deux fois.
Si le code de télécommande n’a pas été saisi correctement le bouton REMOTE
MODE/l’indicateur Remote ne clignote qu’une seule fois.
Remarques :
Antes de que transcurran 30 segundos, utilice los botones numéricos para
introducir el código de mando a distancia de 5 dígitos.
El botón REMOTE MODE/indicador Remote parpadeará dos veces.
Si el código de mando a distancia no se introduce correctamente, el botón REMOTE
MODE/indicador Remote parpadeará una vez despacio.
Notas:
• El parpadeo del mando distancia será distinto según el modelo de receptor de AV.
• El mando a distancia está preconfigurado con los ajustes predeterminados de los distintos
componentes. Al introducir un código de la lista de códigos del mando a distancia se puede
activar el ajuste predeterminado de ese componente.
• Cuando hay múltiples códigos relacionados con un fabricante, pruebe a introducirlos uno a uno
hasta que coincida con su componente.
• Dependiendo del modelo y el año de su componente, la compatibilidad no está garantizada.
• Con algunos modelos, es posible que el mando a distancia no funcione o que su compatibilidad
esté limitada a una parte de las funciones del componente.
• Además, no es posible añadir nuevos códigos a los ajustes predeterminados existentes del
mando a distancia.
• Los códigos de mando a distancia suministrados son correctos en el momento de la impresión,
pero el fabricante puede realizar cambios.
• L’élément clignotant de la télécommande différera selon le modèle de votre ampli-tuner AV.
• La télécommande est préconfigurée avec des préréglages de télécommande de différents
appareils. En entrant un code de la liste des codes de télécommandes, vous pouvez activer le
préréglage approprié pour cet appreil.
• Quand il y a de multiples codes liés à un fabricant, essayez-les et entrez-les un par un jusqu’à ce
que cela corresponde à votre appareil.
• Selon le modèle et l’année de votre appareil, la compatibilité n’est pas garantie.
• Avec certains modèles, la télécommande peut ne pas fonctionner ou sa compatibilité peut être
limitée à une partie de la fonctionnalité de l’appareil.
• En outre, il n’est pas possible d’ajouter de nouveaux codes aux préréglages de télécommande
existants.
• Bien que les codes de télécommande fournis soient corrects au moment de l’impression de la
liste, ils sont susceptibles d’être modifiés par le fabricant.
2
Remote Control Codes
Codici del telecomando
Fernbedienungscodes
1
1
Tenendo premuto il tasto REMOTE MODE al quale si desidera assegnare il
codice, premere e tenere premuto [DISPLAY] (per circa 3 secondi).
Il tasto REMOTE MODE/l'indicatore Remote si accende.
Sui prodotti Integra, i nomi dei tasti sono scritti con l'iniziale maiuscola. Ad esempio,
tasto “Remote Mode” e tasto “Display”.
Note:
• I codici di controllo del telecomando non possono essere inseriti per [RECEIVER] e i tasti multi
zona.
• Per [TV] è possibile immettere solo codici telecomando del televisore.
• Tranne che per [RECEIVER], [TV], e per il tasto multi zona, è possibile assegnare codici di
controllo di ogni categoria per i tasti REMOTE MODE. Tuttavia, tali tasti fungono anche da
tasti del selettore d'ingresso, quindi scegliere un tasto REMOTE MODE che corrisponda
all'ingresso al quale viene collegato il dispositivo. Per esempio, se si collega il lettore CD
all'ingresso CD, scegliere il [TV/CD] quando si immette il relativo codice telecomando.
2
Halten Sie die REMOTE MODE-Taste gedruckt, fur die Sie den Code eingeben
mochten, und drucken Sie (ca. 3 Sekunden lang) die [DISPLAY]-Taste.
Die REMOTE MODE-Taste/Remote-Anzeige leuchtet.
Bei den Integra-Produkten werden die Namen der Tasten groß geschrieben. Zum
Beispiel „Remote Mode“ (Fernbedienungsmodus)-Taste und „Display“-Taste.
Hinweise:
• Der Fernbedienungscode kann nicht [RECEIVER] und der Multi-Zonen-Taste zugeordnet
werden.
• Der Taste [TV] können nur Fernbedienungscodes für einen Fernseher zugeordnet werden.
• Abgesehen von [RECEIVER], [TV] und der Multi-Zone-Taste, können die
Fernbedienungscodes jeder Kategorie den REMOTE MODE-Tasten zugewiesen werden.
Allerdings dienen diese Tasten auch als Quellenwahltasten. Wählen Sie also nach Möglichkeit
eine REMOTE MODE-Taste, die dem Eingang zugeordnet ist, an den Sie die betreffende Quelle
angeschlossen haben. Wenn Sie z.B. einen CD-Player an den CD-Eingang anschließen, sollten
Sie [TV/CD] wenn Sie den Fernbedienungscode eingeben.
Entro 30 secondi utilizzare i tasti numerici per inserire il codice telecomando a 5
cifre.
Il tasto REMOTE MODE/l'indicatore Remote lampeggia due volte.
Se il codice telecomando non viene inserito correttamente, il tasto REMOTE
MODE/l'indicatore Remote lampeggia lentamente una volta.
Note:
2
• L'elemento lampeggiante del telecomando varia a seconda del modello del ricevitore AV.
• Il telecomando è preconfigurato con preselezioni per diversi apparecchi. Inserendo un codice
dall'elenco dei codici telecomando, è possibile attivare la relativa preselezione per tale
apparecchio.
• Se sono presenti più codici relativi allo stesso produttore, provare a inserirli uno a uno finché
non si arrivi al codice corrispondente dell'apparecchio.
• A seconda del modello e dell'anno dell'apparecchio, la compatibilità non è garantita.
• Con alcuni modelli, il telecomando può non funzionare o la sua compatibilità può essere limitata
a una parte della funzionalità dell'apparecchio.
• Inoltre, non è possibile aggiungere nuovi codici alle preselezioni esistenti del telecomando.
• I codici telecomando specificati sono validi alla data della stampa del presente documento, ma
sono soggetti a variazioni da parte del produttore.
Geben Sie mit den Zifferntasten innerhalb von 30 Sekunden den 5-stelligen
Herstellercode ein.
Die REMOTE MODE-Taste/Remote-Anzeige blinkt zwei Mal.
Wenn der Fernbedienungscode nicht ordnungsgemäß eingegeben wurde, blinkt die
REMOTE MODE-Taste/Remote-Anzeige einmal langsam.
Hinweise:
• Das blinkende Element auf der Fernbedienung unterscheidet sich je nach AV-Receiver-Modell.
• Die Fernbedienung ist mit den Voreinstellungen der Fernbedienung der verschiedenen
Komponenten vorkonfiguriert. Indem ein Code aus der Liste der Fernbedienungscodes
eingegeben wird, können Sie die entsprechende Voreinstellung für die Komponente aktivieren.
• Wenn es mehrere Codes gibt, die sich auf einen Hersteller beziehen, versuchen Sie sie einzeln
einzugeben, bis einer mit Ihrer Komponente übereinstimmt.
• Dies hängt vom Modell und Herstellungsjahr Ihrer Komponente ab und die Kompatibilität ist
nicht garantiert.
• Es kann sein, dass bei einigen Modellen die Fernbedienung nicht funktioniert oder ihre
Kompatibilität sich auf nur auf Teile der Funktionalität der Komponente beschränkt.
• Abgesehen davon ist es nicht möglich, den bestehenden Voreinstellungen der Fernbedienung
neue Codes hinzuzufügen.
• Obwohl die angegebenen Fernbedienungscodes dem Stand bei Drucklegung entsprechen, sind
Änderungen durch den Hersteller vorbehalten.
3
Remote Control Codes
Afstandsbedieningscodes
Fjärrstyrningskoder
1
1
Houd terwijl u de REMOTE MODE toets ingedrukt houdt waarvoor u een code
wilt toewijzen de [DISPLAY] toets ingedrukt (ongeveer 3 seconden).
De toets REMOTE MODE (afstandsbedieningsmodus) / Het indicatielampje
afstandsbediening gaat branden.
Op producten van Integra staan de namen van de toetesn in hoofdletters. Bijvoorbeeld,
de toetsen “Remote Mode” en “Display”.
Opmerkingen:
• Fjärrkontrollkoder kan inte anges för knapparna [RECEIVER] och flerzonsknappen.
• Endast fjärrkontrollkoder för tv kan anges för [TV].
• Förutom [RECEIVER], [TV] och flerzonsknappen, kan fjärrkontrollkoder för vilken som helst
kategori tilldelas för knapparna REMOTE MODE. Dessa knappar fungerar dock även som
ingångväljarknappar, så använd en knapp för REMOTE MODE som motsvarar ingången som
du ansluter utrustningen till. Till exempel, om du ansluter din CD-spelare till CD-ingången ska
du välja [TV/CD] när du anger dess fjärrkontrollkod.
• Er kunnen geen afstandsbedieningscodes worden ingevoerd voor [RECEIVER] en de multi
zone-toets.
• Alleen TV afstandsbedieningscodes kunnen worden ingevoerd voor [TV].
• Behalve voor [RECEIVER], [TV] en de multi zone-toets, kunnen afstandsbedieningscodes
vanuit elke categorie worden toegewezen aan de REMOTE MODE toetsen. Deze toetsen
werken overigens ook als ingangsselectortoetsen, kies dus een REMOTE MODE toets die
overeenkomt met de ingang waarop u uw component wilt aansluiten. Kies indien u bijvoorbeeld
uw CD-speler aansluit op de CD-ingang de [TV/CD] toets bij het invoeren van de
afstandsbedieningscode.
2
Håll ned knappen för det REMOTE MODE som du vill tilldela en kod samtidigt
som du trycker och håller ned [DISPLAY] (i cirka 3 sekunder).
REMOTE MODE-knapp/Fjärrindikatorlampa.
På Integra-produkter, är knappnamnens begynnelsebokstav en versal. Till exempel,
”Fjärrläge”-knapp och ”Display”-knapp.
Anmärkningar:
2
Gebruik binnen 30 seconden de cijfertoetsen om de 5-cijferige
afstandsbedieningscode in te voeren.
De toets REMOTE MODE (afstandsbedieningsmodus) / Het indicatielampje
afstandsbediening knippert tweemaal.
Indien de afstandsbedieningscode niet met succes wordt ingevoerd, zal de toets
REMOTE MODE/Remote-indicator eenmaal traag knipperen.
Opmerkingen:
Använd sifferknapparna för att ange den femsiffriga koden inom 30 sekunder.
REMOTE MODE-knapp/Fjärrindikatorlampa blinkar två gånger.
Om fjärrkontrollkoden inte ställdes in, blinkar REMOTE MODEknappen/fjärrindikatorn långsamt en gång.
Anmärkningar:
• Det blinkande elementet på fjärrkontrollen skiljer sig åt beroende på din modell av AV-receiver.
• Fjärrkontrollen har förkonfigurerats med förvalda kanaler på fjärrkontrollen för olika
komponenter. Genom att ange en kod från fjärrkontrollkodlistan, kan du aktivera relevanta
förvalda kanaler för den utrustningen.
• När det finns flera olika koder för en tillverkare ska du försöka att ange dem en och en tills de
stämmer överens med din utrustning.
• Beroende på utrustningens modell och årgång, går det inte att garantera kompatibilitet.
• På vissa modeller kan det hända att fjärrkontrollen inte fungerar eller så kan dess kompatibilitet
vara begränsad till en del av utrustningens funktion.
• Dessutom går det inte att lägga till nya koder till fjärrkontrollens existerande förvalda kanaler.
• Även om erhållna fjärrkontrollkoder är korrekta vid tryckningen, kan de ändras av tillverkaren.
• Het knippergedeelte van de afstandsbediening zal verschillen ten opzichte van het model van
uw AV-receiver.
• De afstandsbediening is voorgeprogrammeerd met voorkeuzetoetsen van verschillende
componenten. Door het invullen van een code uit de afstandsbediening codelijst kunt u de
voorkeuzetoets voor die component activeren.
• Wanneer er meerdere codes gerelateerd zijn aan één fabrikant, probeer deze dan een voor een
totdat de juiste code overeenkomt met uw component.
• Afhankelijk van het model en het bouwjaar van uw component is de compatibiliteit niet
gegarandeerd.
• Bij sommige modellen werkt de afstandsbediening mogelijk niet of is de compatibiliteit ervan
beperkt tot een deel van de functionaliteit van de component.
• Daarnaast is het niet mogelijk om nieuwe codes aan de bestaande voorkeuzetoetsen van de
afstandsbediening toe te voegen.
• Hoewel de gegeven afstandsbedieningscodes correct zijn op het moment van afdrukken, kunnen
deze door de fabrikant gewijzigd worden.
4
Remote Control Codes
遙控代碼
遥控代码
1
1
在按住想指定編碼的 REMOTE MODE (遙控模式)按鈕時,同時按住
[DISPLAY] (顯示)(約 3 秒)。
REMOTE MODE (遙控模式)按鈕 / 遙控指示燈亮起。
在 Integra 系列產品上,按鈕名稱為大寫。 例如,「Remote Mode」(遙控模式)
按鈕和 「Display」(顯示)按鈕。
注意:
• [RECEIVER (接收机)] 和多区域按钮不能输入遥控编码。
• 只能为 [TV (电视)] 输入电视遥控编码。
• 除 [RECEIVER (接收机)]、[TV (电视)] 和多区域按钮外,不能为 REMOTE MODE (遥
控模式)按钮指定任何类别的遥控编码。 但是,这些按钮仍可用作输入选择器按钮,因
此,选择与设备所要连接的输入端对应的 REMOTE MODE(遥控模式) 按钮。 例如,如果
要将 CD 播放机连接到 CD 输入端,应在输入遥控编码时选择 [TV/CD (电视 /CD)]。
• [RECEIER] (接收機)和多區域按鈕不能輸入遙控編碼。
• 您只能為 [TV] (電視)輸入電視遙控編碼。
• 除 [RECEIVER] (接收機)、[TV] (電視)和多區域按鈕外,您可針對 REMOTE MODE
(遙控模式)按鈕指定任何類別的遙控編碼。 但是,這些按鈕仍可用作為輸入選擇器按
鈕,因此,請選擇與您設備所連接輸入接口對應的 REMOTE MODE 按鈕。 例如,如果
要將 CD 播放機連接到 CD 輸入源上,則需在輸入遙控編碼時選擇 [TV/CD]。
2
按住想指定编码的 REMOTE MODE (遥控模式)按钮的同时,按住 [DISPLAY
(显示)] (大约 3 秒钟)。
REMOTE MODE (遥控模式)按钮 / 遥控指示灯亮起。
Integra 产品上的按钮名称单词首字母大写。例如,“Remote Mode (遥控模
式)”按钮和 “Display (显示)”按钮。
注意:
2
在 30 秒內,使用數字按鈕輸入 5 位數的遙控編碼。
REMOTE MODE (遙控模式)按鈕 / 遙控指示燈閃爍兩次。
如果無法成功輸入遙控編碼,REMOTE MODE (遙控模式)按鈕 / 遙控指示燈
會慢慢地閃爍一次。
注意:
在 30 秒内,使用数字按钮输入 5 位数的遥控编码。
REMOTE MODE (遥控模式)按钮 / 遥控指示灯闪烁两次。
如果不能顺利输入遥控编码,REMOTE MODE (遥控模式)按钮 / 遥控指示灯会
缓慢闪烁一次。
注意:
• 根据 AV 接收机产品类型的不同,遥控器闪烁元素将会不同。
• 遥控器采用不同设备的遥控器预设进行预配置。通过从遥控器编码列表输入编码,便
可激活相应设备的相关预设。
• 单个制造商关联多个编码时,请尝试逐个输入,直至符合当前设备。
• 根据设备的产品类型和年份的不同,无法保证兼容性。
• 对于某些产品类型,遥控器可能无法工作或其兼容性可能受到部分设备功能性的限制。
• 此外,可能无法将新的编码追加到现有的遥控器预设。
• 尽管付印时所提供的遥控编码是正确的,但制造商会随时更改。
• 視您的 AV 接收機型號而定,遙控器的閃爍元件會有不同。
• 遙控器已預先設定有不同設備的遙控器預設值。 透過輸入遙控編碼清單中的編碼,您
可啟用該設備的相關預設值。
• 當有多個編碼與單一製造商相關時,請嘗試一個接著一個輸入,直到與您的設備對應
為止。
• 視設備的型號和年份而定,並不保證與本公司產品相容。
• 在某些型號上,遙控器可能無法作用,或是其相容性限於部份設備功能。
• 除此之外,您無法新增編碼至現有的遙控器預設值。
• 雖然所提供之遙控編碼在本文件列印時為正確,製造商仍可能會對其作出修改。
5
Remote Control Codes
Cable Set Top Box
Cable Set Top Box
Cable Set Top Box
Cable/PVR Combination
ADB
02254, 02769
Neuf TV
03107
Visiopass
00817
Time Warner
01376, 01877, 02187
Aon
02769
Noos
00817
VTR
01376
UPC
01582
Arris
02187
NTL
01068, 01060
WideOpenWest
01877
Videotron
01877
AT&T
00858
Numericable
02767
Ziggo
VTR
01376
Bright House
01376, 01877
Ono
01068, 01562
00660, 01666, 02015,
02142, 02447, 02774
BT Vision
02294
Optus
01060
Cable & Wireless
01068
Orange
00817
Cable One
01376, 01877
Pace
01376, 01877, 01068,
01060, 01982
Arris
02187
IPTV
Bright House
01376, 01877
ADB
01376, 01877
Panasonic
01488, 01982
Cable One
01376, 01877
Aon
02769
Charter
01376, 01877, 02187
Philips
Cablevision
01376, 01877
AT&T
00858
Cisco
01877, 00858, 01982,
02345, 02378
00817, 01582, 02294,
02767
Charter
01376, 01877, 02187
BT Vision
02294
Pioneer
01877, 01500
Cisco
01877, 01982
Canal+
02657
00817, 00660, 01666,
02015, 02447
RCN
01376
Comcast
00858, 02345, 02378
01877
01376, 01877, 01982,
02187
Cisco
Rogers
Kreatel
01385
01376, 01877, 01982,
02187
Sagem
00817
Cox
01376, 01877
mio TV
02802
01877, 01060, 01666,
02015, 02774
Digeo
02187
Motorola
Freebox
01482
01376, 00858, 01998,
02378
01877, 00858, 01982,
02345
Humax
02142, 03051, 03053
Neuf TV
03107
Insight
01376, 01877
Pace
02657
Cablecom
Cablevision
Com Hem
Comcast
01582
Samsung
WideOpenWest
01877
Ziggo
02142
Cable/PVR Combination
02254, 02769
Cox
01376, 01877
Daeryung
01877
Digeo
02187
DX Antenna
01500
SFR
03107
J:COM
03051, 03053
00817
01376
00858, 02345
France Telecom
Shaw
Scientific Atlanta
Knology
01877
01482
01998, 02802
03107
Freebox
SingTel
SFR
Mediacom
01376, 01877
01998, 02802
01497
01460
SingTel
Fujitsu
Sony
Motorola
01376
00660, 02142, 02447,
03051, 03053
02015
01385
Humax
Stofa
TeliaSonera
Moxi
02187
Suddenlink
01376, 01877
Telus
02345
Numericable
02767
Insight
01376, 01877
Sumitomo
01500
Thomson
02769
Pace
01877
J:COM
03051, 03053
Telewest
01068
Verizon
02378
Panasonic
01982
Knology
01877
TeliaSonera
01385
Philips
01582, 02767
IPTV/PVR Combination
Kreatel
01385
Telus
02345
Pioneer
01877
ADB
Macab
00817
Thomson
01582, 01982, 02769
Rogers
01877
Aon
02769
Mediacom
01376, 01877
Time Warner
01376, 01877, 02187
Samsung
01877
AT&T
00858
mio TV
02802
Toshiba
01509
Scientific Atlanta
01877, 01982
BT Vision
02294
Motorola
01376, 00858, 01562,
01982, 01998, 02378
UPC
01582
Shaw
01376
Cisco
00858, 02345, 02378
Verizon
02378
Moxi
02187
Suddenlink
01376, 01877
Kreatel
01385
Videotron
01877
NEC
01496
Thomson
01582
Motorola
00858, 02378
Virgin Media
01068, 01060
Scientific Atlanta
6
02769
Remote Control Codes
IPTV/PVR Combination
CD
Neuf TV
03107
Harman/Kardon
70157
Rotel
70157
Onkyo
70868
Philips
02294
Hitachi
70032
SAE
70157
Sony
70490, 70000
Scientific Atlanta
00858
Integra
71817, 70101
Sansui
70157
TEAC
72977
SFR
03107
JVC
70072
SAST
70157
Yamaha
70490
Verizon
02378
Kenwood
70626, 70157, 70036
Siemens
70157
Krell
70157
Silsonic
70036
Cassette Deck
Linn
70157
Simaudio
70157
Aiwa
70157
Arcam
40076
40029
CD/Cassette Dock
TASCAM
73095
CD
Advantage
70032
AH!
70157
Aiwa
70157
Arcam
70157
Atoll Electronique
70157
Audio Research
70157
Audiolab
70157
Audiomeca
70157
Audioton
70157
AVI
70157
Balanced Audio
Technology
70157
Cairn
70157
California Audio Labs 70029, 70303
Cambridge
70157
Cambridge Audio
70157
Carver
70157
CCE
70157
Cyrus
70157
Denon
70626, 70766
DKK
70000
DMX Electronics
70157
Dynaco
70157
Genexxa
70000, 70032
Goldmund
70157
Grundig
70157
Loewe
CD
70157
Sonic Frontiers
MD
40029
Magnavox
70157
Sony
70490, 70000
Audiolab
Marantz
70626, 70029, 70157
Sylvania
70157
Carver
40029
40076
Matsui
70157
TAG McLaren
70157
Denon
MCS
70029
Tandy
70032
Grundig
40029
40029
40070
Memorex
70032
TASCAM
73533, 73095
Harman/Kardon
Meridian
70157
TEAC
73531, 73551, 73532
Inkel
70029, 70303
JVC
40244
40070
Micromega
70157
Technics
Miro
70000
Thorens
70157
Kenwood
Mission
70157
Thule Audio
70157
Magnavox
40029
40029
Myryad
70157
Traxdata
70626
Marantz
NAD
70000, 70721
Universum
70157
Myryad
40029
70072
Onkyo
42157
70000, 70032, 70157
Optimus
40027
40029
Naim
NSM
70157
Victor
70157
Wards
Onkyo
71817
Yamaha
70490, 70032, 70036
Philips
Optimus
70000, 70032
Zonda
70157
Pioneer
40027
Polk Audio
40029
Panasonic
70029, 70303
Philips
70626, 70157
CD-R
Radiola
40029
Pioneer
70032, 70101
Denon
70626, 70766
RCA
40027
Polk Audio
70157
JVC
70072
Revox
40029
70157
Kenwood
70626
Sansui
40029
Proton
70157
Marantz
70626
Sony
40243
QED
70157
Onkyo
71323
Thorens
40029
70157
Philips
70626
Victor
40244
Quasar
70029
Sony
70000
Wards
40027, 40029
Radiola
70157
TASCAM
71830, 72304
Yamaha
40097
RCA
70032
Restek
70157
Primare
Quad
Revox
CD-R/MD
TASCAM
70157
7
Accessory
73511
Apple
81115
Remote Control Codes
Accessory
Satellite Set Top Box
Satellite Set Top Box
Satellite Set Top Box
Jamo
82228
Alba
01284
Centrex
01457
Durabrand
01284
Logitech
82182
Allvision
01334
CGV
01413, 01567
Echostar
Onkyo
82990, 81993, 82351
Amstrad
Chess
01334, 01626
00775, 00853, 01323,
01409, 02527
Polk Audio
82228
00847, 01175, 01662,
01693
CityCom
01176
Eco-Star
01413
Ansonic
02418
Clatronic
01413
Edision
01631
Arnion
01300
Clayton
01626
Elap
01413, 01567
02418
Video - Accessory
ADB
02254, 02769
ASCI
01334
Com Hem
01176, 01915
Elbe
Aon
02769
AssCom
00853
Comag
01413
Energy Sistem
01631, 02418
Apple
02615
Astro
00173, 01100
Comsat
01413
Engel
01251
AT&T
00858
Atlanta
02418
Coship
01457
EuroLine
01251
BT Vision
02294
Atsat
01300
Crown
01284
Europhon
01334
Canal+
02657
AtSky
01334
CS
01631
Europsat
01413, 01611
Cisco
00858, 02345, 02378
Audiola
02418
01409
Expressvu
00775
Kreatel
01385
Aurora
00879, 00642, 01433
Cyfrowy Polsat
00853, 02527
Fagor
01611
mio TV
02802
Austar
00879, 00642, 01259
D-box
00723, 01114
Ferguson
01291
Motorola
01376, 00858, 01998,
02378
Avanit
01631
01626
Finlux
01626
Awa
02418
Denver
02418
Fly Com
01457
Neuf TV
03107
Axil
01413, 01457, 02418
Dgtec
01631, 02418
FMD
01413, 01457
Pace
02657
Axitronic
01626
02418
00879, 01176, 01356
Philips
02294
Balmet
01457
Dick Smith
Electronics
Foxtel
Freesat
02408
Scientific Atlanta
00858, 02345
Bell ExpressVu
00775
Digi Raum Electronics 01176
Fuba
00173, 01251
SFR
03107
Belson
02418
Digiality
01334
Galaxis
00853, 00879
SingTel
01998, 02802
Big Sat
01457
Digihome
01284
General Satellite
01176
TeliaSonera
01385
Black Diamond
01284
DigiLogic
01284
Globo
01251, 01334, 01626
Telus
02345
Blaupunkt
00173
DigiQuest
01300, 01457, 01631
GOI
00775
Thomson
02769
Boshmann
01413, 01631
Digisky
01457
Gold Box
00853
Verizon
02378
Boston
01251
DigitalBox
01100, 01631
Gold Vision
01631
Boxer
01458
Digiwave
01631
GoldMaster
01334
British Sky
Broadcasting
00847, 01175, 01662
DirecTV
01377, 00099
Goodmans
01284, 01291
Dish Network
00775
Gradiente
00099, 00887
BskyB
00847, 01175, 01662
Satellite Set Top Box
Dishpro
00775
Grandin
01626
Bush
01284, 01291, 01626
@sat
01300
DishTV
01300
Grocos
01409, 01457
Canal Digital
00853, 01334
@Sky
01334
DRE
01176
Grundig
Canal Satellite
00853, 02657
01284
01237
00847, 00853, 00173,
00879, 01284, 01291
Acoustic Solutions
Dream Multimedia
Canal+
00853, 02657
02280, 02418
02418
00642, 00887, 01259
DSE
Haier
ADB
CanalSat
00853, 02657
01626
Akura
01626
00879, 00642, 01433
Hallo
Receiver
Onkyo
52503
Cyfra+
Dantax
DSTV
8
Remote Control Codes
Satellite Set Top Box
Satellite Set Top Box
Satellite Set Top Box
Satellite Set Top Box
Hama
01567
Leiko
01626
Pace
Sat Industrie
01611
Hanseatic
01100
Lemon
01334
SAT+
01409
Hirschmann
00173
Lenoxx
01611
Hitachi
01284
Linsar
01284
00847, 00853, 00887,
01175, 01323, 01356,
01423, 01662, 01693,
01850, 02059, 02060,
02211, 02657
Hornet
01300
Listo
01626
Pacific
01284
Schaub Lorenz
02418
HTS
00775
Lodos
01284
Palcom
01409, 01611
Schneider
01206, 01251
Humax
01377, 01176, 01427,
01675, 01808, 01882,
01915, 02144, 02408,
02616
Logik
01284
Panasat
00879, 01433
Schwaiger
01334, 01457, 01631
Macab
00853
Panasonic
00847, 01304, 01404,
03099
Sedea Electronique
01206, 01626
SEG
01251, 01284, 01626
ID Digital
01176
ID Sat
01334
ILLUSION sat
01631
Imperial
01195, 01334
Indovision
00887
Satplus
01100
SatyCon
01631
Manhattan
01300
Maspro
00173
Panda
00173
Servimat
01611
Matsui
00173, 01284, 01626
Pass
01567
ServiSat
01251
Maximum
01334
peeKTon
01457, 02418
Shark
01631
Mediabox
00853
Philips
Sherwood
01409
Mediacom
01206
Siemens
MediaSat
00853
00099, 00853, 00173,
01114, 00887, 00133,
02211
00173, 01334, 01626,
02418
Medion
01334, 01626
Phoenix
02418
Sigmatek
02418
Pino
01334
SKY
Pioneer
00853, 01308
PMB
01611
00099, 00847, 00887,
01175, 01662, 01693,
01850, 02754
00173
Premiere
00723
SKY Brazil
00887
01251
Pro Basic
00853
SKY Deutschland
02754
Movistar
02527, 02761
Proline
01284
SKY Italia
00853, 01693, 01850
Multichoice
00879, 00642, 01433,
02059, 02060
QNS
01404
SKY New Zealand
02211
RCA
01291
SKY PerfecTV!
02299, 02616, 03099
01251
Sky XL
01251
iNETBOX
01237
Inno Hit
01626
Innova
00099
inVion
02418
iotronic
01413
ISkyB
00887
ITT
02418
ITT Nokia
00723
Jadeworld
00642
Jaeger
01334
MySky
01356, 01693, 01850
Regal
JVC
00775
NEOTION
01334
Roadstar
00853
Sky+
01175, 01662
KabelBW
01195, 01882, 01915
Netsat
00099, 00887
Rollmaster
01413
Skymaster
Kaon
01300
Nikko
00723
Rownsonic
01567
01334, 01409, 01567,
01611
Kathrein
00173, 01561, 01567
Nokia
00853, 00723, 01223
SAB
01251, 01300, 01631
Skymax
01413
Nordmende
01611
Sagem
Kenwood
00853
MegaSat
01631
Metronic
01334, 01413, 01631,
02418
Metz
Moserbaer
01114
Koenig
01631
NPG
01631
Saivod
02418
Kreiling
01626
Onn
01284
Samsung
01377, 00853, 01175,
01206, 01458, 01662,
02986
Kreiselmeyer
00173
Optex
01413, 01611, 01626
L&S Electronic
01334
Optus
00879, 01356
Orbis
01334
Orbitech
01100, 01195
LaSAT
Lava
00173
01631
9
Skyplus
01175, 01334
SkySat
01100
Skyvision
01334
SM Electronic
01409
Smart
01404, 01413, 01631
Sansui
01251
SmartVision
01457
Sanyo
01626
Sony
Sat Control
01300
00847, 00853, 01558,
02299
Remote Control Codes
Satellite Set Top Box
Satellite Set Top Box
SAT/PVR Combination
SAT/PVR Combination
Star
00887
UBC
00642
Canal+
02657
SKY Deutschland
02754
Stream System
01300
UEC
00879, 01356
CanalSat
02657
SKY Italia
01693, 01850
Strong
00853, 00879, 01284,
01300, 01409, 01626,
02418
United
01251, 01626, 02418
Cyfrowy Polsat
02527
SKY New Zealand
02211
Unitymedia
01882
DigiQuest
01300
SKY PerfecTV!
02299, 03099
Universum
00173, 01251
DirecTV
01377, 00099, 20739
Sky+
01662
Variosat
00173
Dish Network
00775
Skyplus
01175, 01334
VEA
02418
Dishpro
00775
Smart
01631
Vestel
01251, 01284
Dream Multimedia
01237
Sony
02299
Viasat
01195
Echostar
00775, 02527
Stream System
01300
Vision
01626
Edision
01631
Strong
01300
Visiosat
01413, 01457
Expressvu
00775
Sunny
01300
Vitecom
01413
Foxtel
01356
TechniSat
01195
Vivax
02418
Humax
Technosat
01206
Volcasat
02418
01176, 01427, 01675,
01808
Telefonica
02527
Wavelength
01413
ID Sat
01334
Telestar
01195
Wharfedale
01284
iNETBOX
01237
Thomson
01175, 01662
Wisi
00173
Kaon
01300
Topfield
01206
Worldsat
01251
Kathrein
01561
Viasat
01195
Woxter
02418
Maximum
01334
Xtreme
01300
Xsat
00847, 01323
Mediacom
01206
Xtreme
01300
MegaSat
01631
Television
01413
Movistar
02527
A.R. Systems
10556, 10037
Yes
00887
Multichoice
02059, 02060
Accent
10037
Zehnder
01251, 01334, 01413,
01631
MySky
01356, 01693, 01850
Acer
11339
NEOTION
01334
Acoustic Solutions
11037, 11667
02280, 02761
Pace
01175, 01356, 01423,
01662, 01693, 01850,
02059, 02060, 02211,
02657
Action
10650
Sunny
01300
Sunstar
00642
Supernova
00887
Supratech
01413
Systec
01334
Sytech
02418
TBoston
01251, 02418
TEAC
01251
Technical
01626
Technika
01284
TechniSat
01100, 01195
Technosat
01206
Techwood
01251, 01284, 01626
TELE System
01251, 01409, 01611
Telefonica
02527, 02761
Telestar
01100, 01195, 01251,
01334, 01626
Televes
01300, 01334
Televisa
00887
Tevion
01409
Thomson
00847, 00853, 01175,
01046, 01291, 01662
Tonna
01611
Topfield
01206
Toshiba
01284
Trevi
Triax
01251
00853, 01251, 01291,
01413, 01611, 01626,
01631
Yakumo
Zinwell
SAT/PVR Combination
@sat
01300
Amstrad
01175, 01662, 01693
Atsat
01300
Bell ExpressVu
00775
01175, 01662
Tricolor TV
01176
British Sky
Broadcasting
True Visions
02408
BskyB
01611
Canal Satellite
Twinner
Panasonic
Philips
Samsung
01304, 03099
00099
01175, 01206, 01662
Sat Control
01300
Schneider
01206
Addison
10653
AEG
11037, 11324
Agfaphoto
12719
Aiko
10037
Aim
10037, 10499
Akai
10178, 10556, 10037,
10714, 10715, 10208,
11675
01175, 01662
Sedea Electronique
01206
Akiba
10037
02657
SKY
01175, 01662, 01693,
01850, 02754
Akito
10037
10
Remote Control Codes
Television
Akura
Alba
Alien
Television
10171, 10037, 10714,
10668, 11037, 11363,
11585, 11667, 11709
10037, 10714, 10668,
11037, 11585
11037
Allstar
10037
Amstrad
10171, 10037, 11037
Anam
10037
Television
11037
Classic
10499
DMTech
12001
Beon
10037
Clatronic
10037, 10714, 11324
Domeos
10668
Berthen
10556, 10668
Clayton
11037
Drean
10037
Bestar
10037
Condor
10037
DSE
10698
Bexa
12493
Conrowa
10698
Dual
Black Diamond
11037
Contec
10037
10037, 11037, 11585,
11667
Blaupunkt
10195
Cosmel
10037
Durabrand
Blue Sky
10556, 10037, 10625,
10714, 10668, 11037,
10715, 10499, 11324,
11363, 11652, 11709
CPTEC
10625, 11363
10178, 10171, 10714,
11037, 11652
Crown
10037, 10714, 10668,
11037, 10715, 10208,
11652
Dux
10037
Anam National
10037, 10650
Andersson
11585
Anitech
10037
Boca
11652
Cyberpix
Ansonic
10037, 10668
Boman
11324
D-Vision
AOC
10178, 10625, 11365
Bork
11363
Ardem
10037, 10714
BPL
10037, 10208
Arena
10037
Brandt
Aristona
10556, 10037
ART
11037
Art Mito
Asberg
DX Antenna
11817, 13817
Dynatron
10037
11667
Dynex
12049
10556, 10037
e-motion
11709
Daewoo
10178, 10556, 10037,
10634, 10499, 12098
E:max
11324
Easy Living
11666, 11709
10625, 10714, 10560
Dansai
10037, 10208
ECE
10037
Brimax
11709
Dantax
10556, 10037
10037, 10668
10714, 11037, 10715,
11652
Elbe
Brinkmann
11585
Brionvega
10037
Datsura
10208
10037
Bush
10556, 10037, 10714,
10668, 11037, 10698,
10208, 11585, 11652,
11667, 12719
Dawa
10037
Daytron
10037
Astra
10037
ATD
10698
Atlantic
10037
Audiosonic
10037, 10714, 10715
Audioworld
10698
Aventura
10171
Axxon
10714
Baird
10208
Barco
10556
Basic Line
10556, 10037, 10668,
11037
Baur
10037, 10195, 10512
Beaumark
10178
Beijing
10208
Beko
10037, 10714, 10715,
11652
Belson
Television
Belstar
10698
Byd:sign
12140, 12209
Camper
10037
Carad
10668, 11037
Carena
10037
Carrefour
10037
Cascade
10037
Casio
De Graaf
10208
DEC
11709
Decca
10037
Electrograph
11755
Element
11886
Elfunk
11037
ELG
10037
Elin
10037
Elite
10037
Emerson
10178, 10171, 10037,
10714, 10668, 11394,
11864, 11886
Denver
10037, 11709
Desmet
10037
Diamant
10037
Envision
11365, 11506
Diamond
10698
Epson
11379
10037
Dick Smith
Electronics
10698
Erres
10037
Cathay
10037
ESA
10171
Digatron
10037
CCE
10037
ESC
10037
Digihome
11667
Centrum
11037
Euroman
10037
Digiline
10037, 10668
Centurion
10037
Europa
10037
Digitek
11709
Changhong
10508
Europhon
10037
Digitor
10037, 10698
Chimei
11666
Evesham
11248, 11667
Dixi
10037
Clarivox
10037
Excello
11037
DL
11363
Exquisit
10037
11
Remote Control Codes
Television
Ferguson
Television
10037, 10625, 10560,
10195, 11037, 11585
Fidelity
10171, 10037, 10512
Finlandia
10208
Finlux
10556, 10037, 10714,
10715, 11248, 11667
Firstline
10556, 10037, 10714,
10668, 11037, 10208,
11363
Fisher
10208
Flint
10037
Formenti
10037
Fraba
10037
Friac
10037, 10499
Fujicom
11709
Fujitsu
10809
Fujitsu Siemens
10809, 11248, 11666
Funai
10171, 10714, 10668,
11037, 11394, 11666,
11817, 13817
G-Hanz
11363
Gaba
11037
Galaxi
10037
Galaxis
10037
Gateway
11755
GE
10178, 11454, 10625,
10560
Goodmans
Gorenje
Gradiente
Graetz
Television
10556, 10037, 10625,
10714, 10560, 10668,
10634, 11037, 10499,
11585, 11667
11585
10037
10714
Granada
10037, 10560, 10208
Grandin
10556, 10037, 10714,
10668, 11037, 10715,
11652
Television
Hoeher
10714
Karcher
10714, 11324
Hornyphon
10037
Kathrein
10556
Hugoson
11666
Kendo
10037, 11037, 11585
Humax
11295
Kennex
11037
Hypson
10556, 10037, 10714,
10668, 11037, 10715
Kioto
10556
Kiton
10037, 10668
11037, 10698
KLL
10037
Iberia
10037
Kneissel
10556, 10037, 10499
ICE
10037
Koenig
10037
iLo
11394
Kolin
10037
10150, 10037, 11610,
11755
Hyundai
Grundig
10556, 10037, 10195,
11223, 11667, 12625
Imperial
Indiana
10037
Kolster
10037
GVA
11363, 12098
Ingelen
10714
Konka
10037, 10714
H&B
12001
Inno Hit
11037, 11585
Korpel
10037
Haier
10037, 10698, 10508
Innova
10037
Kosmos
10037
Hallmark
10178
Insignia
10171, 11423, 12049
Kunlun
10208
Hankook
10178
Integra
11807, 13100, 13500
L&S Electronic
10714
Hanseatic
10556, 10037, 10625,
10714, 10634, 10499,
12001
Interbuy
10037
Lavic
11363
Interfunk
10037, 10512
Lavis
11037
Internal
10556
Lecson
10037
Intervision
10037
Lenco
10037, 11037
Irradio
10037
Leyco
10037
IRT
10698
LG
Isukai
10037
10178, 10556, 10037,
10714, 10715, 10698,
11423, 11768, 11840,
12182, 12358, 12424,
12834
Hantarex
10037
Hantor
10037
Harwood
10037
Hauppauge
10037
HB
11324
HCM
10037
GEC
10037
Highline
10037
Genesis
10037
Hinari
10037, 10208
Genexxa
10037
Hisawa
10714
GFM
10171, 11864, 11886
Hisense
Godrej
11585
10556, 10508, 10208,
11363, 12098
Goldfunk
10668
GoldStar
10178, 10037, 10714,
10715
ITS
10037
ITT
10208
ITT Nokia
10208
Liesenkoetter
10037
ITV
10037
Lifetec
JGC
11709
10037, 10714, 10668,
11037, 12001
Jinfeng
10208
Linsar
11585
10150, 10178, 10037,
10634, 11037, 10508,
10499, 10578, 11576,
11585, 11643, 11667,
11691, 12433
Jinxing
10556, 10037, 10698
Local India TV
10208
JMB
10556, 10634, 10499
Local Malaysia TV
10698
Jubilee
10556
Lodos
11037
JVC
10650, 10653, 10508,
11428, 11601, 12271
Loewe
10037, 10512, 11884
Hitachi Fujian
10150
Logik
11037, 10698
Kaisui
10037
Hitec
10698
Logix
10668
Hitachi
12
Remote Control Codes
Television
Television
Television
Television
Luma
11037
Metronic
10625
NetTV
11755
Orline
10037
Lumatron
10037, 10668
Metz
10037, 10668, 10195,
11037
Neufunk
10556, 10037, 10714
Ormond
10668, 11037
Lumenio
10037
New Tech
10556, 10037
Osaki
10556, 10037
Lux May
10037
MGA
10150, 10178
Newave
10178
Osio
10037
Luxor
11037, 10208
Micromaxx
Nikkai
10037
Osume
10037
LXI
10178
10037, 10714, 10668,
11037, 11324, 12001
Nikkei
10714
Otto Versand
M Electronic
10037, 10714, 10634,
10195, 10512, 11652
Nikko
10178
10556, 10037, 10195,
10512
Nokia
10208
Pacific
Norcent
11365
10556, 10714, 11037,
11324
Nordmende
10037, 10714, 10560,
10195, 11585, 11667,
12001
Palladium
10556, 10037, 10714
Microspot
11614
Mikomi
11037, 11585
10037
Madison
10037
Minato
Magnavox
10171, 11454, 11365,
11506, 11755, 11867,
12372
Minerva
10195, 11248
Ministry Of Sound
11667
Minoka
10037
Magnum
10037, 10714, 10715
Mirai
11666
Normerel
10037
Manesth
10037
Mitsubishi
10150, 11250, 10178,
10556, 10037, 11037,
10512, 11171
Nortek
10668
Manhattan
10037, 10668, 11037
Marantz
11454, 10556, 10037
Mark
10037, 10714, 10715
Mivar
Master's
10499
Moree
10037
10698
Morgan's
10037
Masuda
10037
Moserbaer
11585
Matsui
10556, 10037, 10714,
10195, 11037, 10208,
11666, 11667
MTC
10512
MTlogic
10714
Mudan
10208
Mastro
10609
Matsushita
10650
Multitec
10037, 10668, 11037
Maxent
11755
Multitech
10037
Maxess
12493
Myrica
11666
Meck
10698
Myryad
10556
NAD
10178, 10037
10556, 10037, 10714,
10668, 11037, 10698,
10512, 11248, 11585,
11667, 12001, 12719
Naiko
10037
Nakimura
10037
National
10508, 10208
Megatron
10178
NEC
MEI
11037
10178, 10653, 10508,
10499
Neckermann
10556, 10037
NEI
10037, 11037
NEO
11324
Mediator
Medion
Memorex
10556, 10037
10150, 10178, 11037
Mercury
10037
Mermaid
10037
Netsat
10037
13
Novatronic
10037
Novita
11585
Nu-Tec
10698
O.K.Line
11037, 11324
Oceanic
10208
Odys
12719
Okano
10037
OKI
11585, 11667
Olevia
11610, 12124
Omni
10698
Onei
11667
Onida
10653
Palsonic
10037, 10698
Panama
10037
Panasonic
11480, 10037, 10650,
10508, 10208, 11636,
12170
Panavision
10037
Panda
10698, 10508, 10208
Pansonic
11636
Penney
10178
Perdio
10037
Perfekt
10037
Petters
10037
Philco
10178, 10171, 10037,
11394
Philips
10178, 10171, 11454,
10556, 10037, 10512,
10605, 10690, 11394,
11506, 11867, 12372
Onimax
10714
Onix
10698
Phocus
10714, 11652
Onkyo
11807, 13100, 13500
Phoenix
10037
Onn
11667, 11709
Phonola
10556, 10037
Onyx
11709
Pioneer
Opera
10037, 10714
10037, 10698, 10512,
11457, 11636, 12171
Optimus
10650
Plantron
10037
Orbit
10037
Playsonic
10037, 10714, 10715,
11652
Orion
10556, 10037, 10714,
11037, 12001
Powerpoint
10037, 10698
Prinston
11037, 10715
Remote Control Codes
Television
Television
Television
Television
Profitronic
10037
Rowa
10037, 10698
Siera
10556, 10037
Svasa
Proline
10037, 10625, 10634,
11037
Saba
10625, 10714, 10560
Silva
10037
Swisstec
11614, 11775
Sagem
10618
Silva Schneider
10037
Sylvania
10037, 10714, 10668,
11324, 11585, 11667,
11709, 12001
Saivod
10037, 10668, 11037
Silver
10715
10171, 11394, 11864,
11886
Salora
10208, 12001
SilverCrest
11037
Symphonic
10171, 11394
Sinudyne
10037
Synco
10178, 11755
SKY
10037, 11614, 11775
Syntax
11610
10037, 10698
Sysline
10037
Sliding
11324
Tacico
10178
SLX
10668
Talent
10178
10650
Prosonic
Protech
10037, 10668, 11037
Proton
10178
ProVision
10556, 10037, 10714,
11324
Pvision
12001
Pye
10556, 10037
Qingdao
10208
Quasar
10650
Quelle
10037, 10668, 10195,
11037, 10512
R-Line
10037
Radiola
10556, 10037
Radiomarelli
10037
RadioShack
10178, 10037
Radiotone
10037, 10668, 11037
RCA
10178, 11454, 10625,
10560, 10618, 11781,
12247, 12403, 12434,
12746, 12932
Realistic
10178
Recor
10037
Rectiligne
10037
Sampo
Samsung
10178, 10171, 10650,
11755
10178, 10556, 10037,
10618, 10650, 10208,
12051
Skyworth
10208
Sansui
10171, 10037, 10714,
11248, 12001
Solavox
10037
Tashiko
Sanyo
11037, 10508, 10208,
11142, 11365, 11585,
11667, 11974
Soniko
10037
Tatung
10037, 11248, 11324
12493
TCL
Sonitron
10208
10698, 12403, 12434,
13183
10556, 10037
Sonneclair
10037
TCM
10714, 12001
TEAC
10178, 10171, 10037,
10714, 10668, 11037,
10698, 10512, 11248,
11363, 11709, 11755
SBR
Soniq
Schaub Lorenz
10714, 11324, 11363,
11667, 12001
Sonoko
10037
Schneider
10556, 10037, 10714,
10668, 11037
Sonolor
10208
Sontec
10037
Sony
10810, 11505, 11167,
11651, 11825
Tec
10037
Tech Line
10037, 10668
Soundesign
10178
Technica
11037
Soundwave
10037, 11037, 10715
Technics
10556, 10650
Sowa
10178
Technika
11667
Squareview
10171
TechniSat
10556
Standard
10037, 11037, 11709
Technisson
10714, 11652
Starlite
10037
Techno
11585
10037
Technosonic
11610
10556, 10625, 10499,
11324
11709
Schoentech
Scotch
Scott
Sears
11037
10178
10178
10178, 10171
Seaway
10634
Seelver
11037
SEG
10037, 10668, 11037,
12719
10037
SEI
10037
Strato
Reflex
10037, 10668, 11037
Sei-Sinudyne
10037
SunBriteTV
Relisys
11585
Serie Dorada
10178
Sungoo
11248
Techvision
Remotec
10171, 10037
Shanghai
10208
Sunny
10037
Techwood
11037, 11667
Reoc
10714
Sharp
10037
Tecnimagen
10556
Revox
10037
10650, 10818, 11165,
11423, 11659
Sunstar
Sunstech
12001
Teco
10178, 10653
RFT
10037
Shintoshi
10037
Sunwood
10037
Tedelex
10208, 11709
Roadstar
10037, 10714, 10668,
11037, 10715
Shivaki
10178, 10037
Supersonic
10208
Teknika
10150
Siam
10037
SuperTech
10556, 10037
TELE System
11585
Siemens
10037, 10195
Supra
10178
Telecor
10037
Redstar
Rolson
12001, 12098
14
Remote Control Codes
Television
Telefunken
Telefusion
Television
10037, 10625, 10714,
10560, 10698, 11585,
11667
10037
Television
Ultravox
10037
UMC
11614, 11775
Unic Line
10037
Uniden
United
Wharfedale
PVR
10556, 10037, 11324,
11667
ReplayTV
20616
Sonic Blue
20616
White Westinghouse
10037
TiVo
20739
12122
Wilson
10556
10556, 10037, 10714,
11037, 10715, 11652
Windsor
10668, 11037
TV/VCR Combination
Windy Sam
10556
Telegazi
10037
Telemeister
10037
Amstrad
10171
Telesonic
10037
Unitek
11709
Wintel
10714
Ferguson
10625
Telestar
10556, 10037
Universal
10037, 10714
World-of-Vision
12001
Fidelity
10171
Teletech
10037, 10668, 11037
Universum
Wyse
11365
GoldStar
10037
Teleview
10037
10037, 10668, 10195,
11037, 10618, 10512
Xenius
10634
Grundig
10556, 10037, 10195
Tennessee
10037
Univox
10037
Xiahua
10698
LG
10178
Tensai
10037, 11037, 10715
V7 Videoseven
11666, 11755
XLogic
10698
Mitsubishi
10556
Tesla
10556, 10037, 10714,
11037, 11652
Vestel
10037, 10668, 11037,
11585, 11667
Xrypton
10037
Philips
10556, 10037
Tevion
10556, 10037, 10714,
10668, 11037, 11248,
11585, 11667
Vexa
10037
Yamaha
10650, 11576
Radiola
10556
Yamishi
10037
Saba
10625
Yokan
10037
Sanyo
11974
Yoko
10037
Schneider
10556, 10037
YU-MA-TU
10037
Sharp
10818
Zenith
10178, 10037, 11365,
11423, 12358
Siemens
10037
Sony
11505
10178, 10171
Thomson
10037, 10625, 10560
Thorn
10037, 10499, 10512
Thorn-Ferguson
10499
TMK
10178
Tokai
10037, 10668, 11037
Tokaido
11037
Topline
10668, 11037
Toshiba
10195, 11037, 10618,
10650, 10508, 11169,
11508, 11524, 11652,
12203
Victor
10650, 10653, 11428
Videocon
10037, 10508
VideoSystem
10037
Vidtech
10178
Viewsonic
11365, 11755, 12049
Vision
10037
Zepto
11585
Vistron
11363
TEAC
Zonda
10698
Vivax
11709
Technics
10556
Thomson
10625
Vizio
11758, 12209
VCR
Vortec
10037
DirecTV
20739
DVD
Voxson
10178, 10037
Humax
20739
3D LAB
30539
VU
11365, 12098
Panasonic
20616
Accurian
30675
Toyoda
11709
Walker
11667
Philips
20739
Acoustic Solutions
30713
TRANS-continents
10556, 10037, 10668,
11037
Waltham
10037, 10668, 11037
ReplayTV
20616
AEG
30675
Wansa
12098
Sonic Blue
20616
Transonic
10037, 10698, 10512,
11363
AFK
31152
Wards
10178
TiVo
20739
Aiwa
30533
Triad
10556
Watson
10037, 10714, 10668,
11037
PVR
Akai
30675
Trio
11248
10037
DirecTV
20739
Triumph
10556, 10037
Welltech
10714, 11652
Humax
20739
TVTEXT 95
10556
Weltstar
11037
Panasonic
20616
Uher
10037
Westinghouse
11755
Philips
20739
Wega
15
Alba
30539, 30713
Ambiance
33052
Amstrad
30713
Anthem
32820
Remote Control Codes
DVD
DVD
DVD
DVD
Aristona
30539, 30646
Elfunk
30713
Kennex
30713
Orion
30713
ASDA
32213
Elite
31152
Kenwood
30490, 30534
Ormond
30713
Audix
30713
Emerson
30675, 32213
Lenco
30713, 33052
Pacific
30713
Autovox
30713
EuroLine
30675
Lexicon
32545
Palladium
30713
Awa
32587
Ferguson
30713
LG
30741, 31602
Panasonic
Basic Line
30713
Finlux
30741
Limit
33052
Bel Canto Design
31571
Firstline
30713
Lodos
30713
30503, 30490, 31579,
31641, 32523, 32710,
32859
Black Diamond
30713
Foehn & Hirsch
33052
Loewe
Blue Parade
30571
Funai
30675
30539, 30741, 32474,
32783
Blue Sky
30713
GE
30522
Logik
30713
Brandt
30503
GFM
30675
Lumatron
30741, 30713
30741
Pelican Accessories
30533
Philco
30675
Philips
30503, 30539, 30646,
30675, 30713, 31340,
31354, 32056, 32084,
32434, 32689
Pioneer
30571, 30142, 30631,
31571, 32442, 32860
30539
Bush
30713
Global Sphere
31152
Lunatron
C-Tech
31152
Go Video
30741
Luxman
30573
30713
30503, 30539, 30646,
30675, 30713, 31354
Polk Audio
Presidian
30675
Manhattan
30713
ProAudio
31394
Marantz
30539, 32414, 32432,
33444
Proscan
30522
Proson
30713
Pye
30539, 30646
California Audio Labs 30490
GoldStar
30741
Luxor
Cambridge Audio
Goodmans
30713, 31152
Magnavox
Centrum
32808
30675, 30713
GPX
30741
Changhong
30627
Grandin
30713
Cinetec
30713
Grundig
30539, 30713
Clatronic
30675
H&B
30713
Clayton
30713
Haaz
31152
Crown
30713
Hanseatic
30741
Dantax
30539, 30713
Harman/Kardon
30582, 31229, 33228
Denon
30490, 30634, 31634,
32258, 32748
Henss
30713
Hitachi
30573, 30713, 31664
Dick Smith
Electronics
31152
Hoeher
30713
Digihome
30713
HotMedia
31152
DigiLogic
30713
Humax
30646
Digix Media
31394
Inno Hit
30713
Disney
30675
Insignia
30741, 30675, 32428,
32596
DSE
30675, 31152
Dual
30713
Integra
30503, 30571, 30627,
31612, 31634, 32147
Mark
30713
Matsui
30713
Maxim
30713
MDS
30713
Medion
30630, 30741
Memorex
Metz
Radionette
30741
Radiotone
30713
RCA
30522, 30571, 32213,
32587
32213
REC
30490
30571, 30713
Red
32213
Micromedia
30503, 30539
Redstar
31394
Micromega
30539
Roadstar
30713
Microsoft
30522, 32083
Rotel
30623
Minax
30713
Salora
30741
Mitsubishi
30713
Samsung
Momitsu
33052
30490, 30573, 30199,
30820, 31635, 32069,
32329, 32489, 33195
30713
Durabrand
30675, 30713
Irradio
30646
NAD
30741
Dynex
32596
JVC
NEC
30741, 31602
Sanyo
Dyon
33052
30539, 30646, 30713
31152
30503, 30627, 31612,
32147, 30571, 31634
Schneider
eBench
30503, 30539, 30623,
30867, 31597, 31602,
32855
Schoentech
30713
30713
Oppo
30575, 32545
Scott
31394
Kendo
Onkyo
16
Remote Control Codes
DVD
DVD
SEG
30713
Semp
30503
Sharp
30630, 30675, 30713,
32250, 32474, 32652,
32869
Sherwood
Blu-ray Disc
DVD-R
30503, 31639, 32277,
32551, 32705, 33157
JVC
32855
Irradio
Lenco
33052
JVC
31597
Transonic
31394
Lexicon
32545
LG
30741
TVE
30713
LG
30741, 31602
Loewe
30741
United
30675, 30713, 31152
30741, 33052
Limit
33052
Magnavox
30646, 30675
Universum
30741, 30713
Shinsonic
30533
Loewe
32474, 32783
Medion
30741
Urban Concepts
30503
Silva Schneider
30741
Magnavox
30675
Panasonic
Vestel
30713
31152
32414, 32432, 33444
30490, 31579, 32523,
32710, 32859
SilverCrest
Marantz
Victor
31597
33052
30646, 31340
30539, 30713
Momitsu
Philips
Skantic
Vizio
32563
30631, 32860
SM Electronic
31152
Vtrek
32587
Pye
30646
Smart
30713
Waltham
30713
32147, 32900, 32910,
33100, 33101, 33500,
33501
Pioneer
RCA
30522
Sony
30533, 30864, 31033,
31070, 31431, 31516,
31633, 32180
Wellington
30713
Oppo
32545
Samsung
30490, 31635
Weltstar
30713
Panasonic
31641, 32523, 32859
Schneider
30646
Wharfedale
30713
Philips
32084, 32434, 32689
Sharp
30630, 30675, 32869
Windsor
30713
Pioneer
30142, 32442
Sony
Windy Sam
30573
Samsung
30199, 33195
31033, 31070, 31431,
31516, 31633, 32180
30522, 32083
Sharp
32250, 32474, 32652
Sylvania
30675
XLogic
31152
Sherwood
33052
Targa
30741
Yamaha
30490, 30539, 30646,
30817, 31354, 32298,
32299
Sony
31516, 32180
Toshiba
31639, 32277, 32551
Sylvania
30675
Victor
31597
TASCAM
34004
Yamaha
30646
30503, 30741
Toshiba
32551, 32705, 33157
Zenith
30741
Vizio
32563
Yamaha
32298, 32299
Soundwave
30713
Star Clusters
31152
Strato
31152
Strong
30713
Supervision
31152
Sylvania
30630, 30675
Symphonic
30675
Toshiba
Xbox
Onkyo
30646
Tamashi
31394
Tandberg
30713
Targa
30741
Blu-ray Disc
Tchibo
30741
Ambiance
33052
TCL
32587
Anthem
32820
DVD-R
TCM
30741
Cambridge Audio
32808
Accurian
TEAC
34004, 30571, 30741,
30675, 31394
Denon
32258, 32748
Aristona
Dyon
33052
Technica
30713
Denon
30490
Foehn & Hirsch
33052
Technics
30490
Emerson
30675
Funai
30675
30713
30675
TV/DVD Combination
Techwood
Funai
Harman/Kardon
33228
30741
11675
30713
Go Video
Akai
Teletech
Insignia
30675, 32428, 32596
11037, 30713
Theta Digital
30571
30741
Black Diamond
Integra
11037, 30713
30522
31664
Blue Sky
Thomson
32147, 32900, 32910,
33100, 33101, 33500,
33501
30646
Bush
11037, 10698, 12719,
30713
Zenith
GPX
Hitachi
Humax
17
HD-DVD
Integra
32901, 33104, 33504
LG
30741
30675
Microsoft
32083
30646
Onkyo
32901, 33104 33504
Xbox
32083
Remote Control Codes
TV/DVD Combination
TV/DVD Combination
Centrum
11037, 30713
Sunstech
12001
Crown
11037, 30713
Sylvania
10171, 11394, 11864,
11886, 30630, 30675
10698
DMTech
12001
Dual
11037, 30713
TEAC
12049
Technica
11037, 30713
Elfunk
11037, 30713
Telefunken
10698
Emerson
11394, 11864, 11886,
30675
Teletech
11037, 30713
Thomson
10625
Ferguson
11037, 30713
Toshiba
11524
Goodmans
11037, 30713
United
11037, 30713
Grandin
30713
Universum
30713
Grundig
30539
Vestel
11037
H&B
12001
Viewsonic
12049
Hanseatic
12001
Weltstar
11037, 30713
Hitachi
11037, 11667, 30713
Dynex
Insignia
12049
JVC
12271
LG
11423
Logik
11037, 30713
Luxor
11037, 30713
Magnavox
12372
Matsui
11037, 30713
Medion
12719
Nordmende
12001
Odys
12719
Panasonic
12170
Philips
11454, 10556, 11394,
30539
Powerpoint
10698
Prosonic
12001
Pvision
12001
RCA
12746, 12932
Schaub Lorenz
12001
SEG
11037, 12719, 30713
Sharp
10818
Soniq
12493
18
Remote Control Codes
Memo
19
Y1212-1
SN 29401471CODE
(C) Copyright 2013 Onkyo Corporation Japan. All rights reserved.
* 2 9 4 0 1 4 7 1 C O D E *