AZ1150/00 eng
2/8/01 11:21
Page 1
MP3-CD Soundmachine
1150
AZ 1155
AZ
Audio
AZ1150/00 eng
2/8/01 11:21
AZ 1150 /00
page
Page 2
2
Important notes for users in the U.K.
Mains plug
This apparatus is fitted with an approved 13 Amp
plug.To change a fuse in this type of plug proceed
as follows:
1. Remove fuse cover and fuse.
2. Fix new fuse which should be a BS1362
5 Amp, A.S.T.A. or BSI approved type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
plug fitted in its place. If the mains plug contains a
fuse, this should have a value of 5 Amp. If a plug
without a fuse is used, the fuse at the distribution
board should not be greater than 5 Amp.
Note:The severed plug must be disposed of to
avoid a possible shock hazard should it be
inserted into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with
the following code: blue = neutral (N), brown =
live (L). As these colours may not correspond
with the colour markings identifying the terminals
in your plug, proceed as follows:
• Connect the blue wire to the terminal marked
N or coloured black.
• Connect the brown wire to the terminal
marked L or coloured red.
• Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain that
the cord grip is clamped over the sheath of the
lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may require
consent. See Copyright Act 1956 and The
Performer’s Protection Acts 1958 to 1972.
2
Norge
Typeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundert
innkoplet. Den innebygde netdelen er derfor
ikke frakoplet nettet så lenge apparatet er
tilsluttet nettkontakten.
For å redusere faren for brann eller elektrisk
støt, skal apparatet ikke utsettes for regn eller
fuktighet.
Italia
DICHIARAZIONE DI CONFORMITA’
Si dichiara che l’apparecchio Lettore CD/Radioregistratore mod. AZ1150, AZ1155 Philips
risponde alle prescrizioni dell’art. 2 comma 1
del D. M. 28 Agosto 1995 n. 548.
Philips Consumer Electronics
Philips, Glaslaan 2, SFF 10
5616 JB Eindhoven,The Netherlands
AZ1150/00 eng
2/8/01 11:21
AZ 1150 /00
page
Page 3
3
^
1
2
3
%
4
$
#
@
5
6
7
8
!
0
9
*
AC MAINS
&
1
%
$
CD
B
K
VOLUME
REPEAT
L
SHUFFL
MUTE
#
BASS
E
2
3
4
5
6
)
(
@
SEARCH
TUNER
!
0
PRESET
TUNIN
BAND
7
8
9
G
3
AZ1150/00 eng
AZ 1150 /00
2/8/01 11:21
page
Page 4
4
Index
Français
Français
18
Español
Español
32
Deutsch
Deutsch
44
Nederlands
Nederlands
56
Italiano
Italiano
68
Svenska
80
Dansk
92
Svenska
English
English
Dansk
4
6
AZ1150/00 eng
AZ 1150 /00
2/8/01 11:21
page
Page 5
5
Português
116
E
128
Portugês
104
E
Suomi
Suomi
Index
5
AZ1150/00 eng
2/8/01 11:21
AZ 1150 /00
page
Page 6
6
Controls
English
Top and front panels
1 2; – starts or pauses MP3-CD/CD
playback
2 OPEN•CLOSE – press to open/close
CD door
3 BAND – selects FM/ MW (AM)/LW
waveband (LW not on all versions)
4 PROGRAM
– MP3-CD/CD: programs/ reviews
programmed tracks;
– TUNER: programs tuner stations
5 CD MODE
– plays MP3-CD tracks/CD/a program in
random order
– repeats a track/MP3-CD/CD/ program
10 Display – backlit only when using AC
mains supply
– MP3-CD: orange backlight
– TUNER/CD: green backlight
11 - ALBUM, PRESET
– MP3-CD only: selects previous album
– TUNER: selects previous preset station
12 SOURCE – selects sound source for
MP3-CD/CD or TUNER
13 POWER – switches the set on/ off
14 LOW BATT – indicator lights up if
battery power running low
15 ULTRABASS 2 – enhances bass
response
16 VOLUME – adjusts volume level
6 + ALBUM, PRESET
– MP3-CD only: selects next album
– TUNER: selects the next preset station
7 ROTARY NAVIGATION 5 , 6
– MP3-CD/CD: fast searches backwards,
forwards within a track
– TUNER: tunes radio (manually: down, up)
¡ ,™
– MP3-CD/CD: skips to previous, next
title/track
– TUNER: automatic search tuning
(down, up)
8 STOP 9 – stops MP3-CD/CD playback;
erases a MP3-CD/CD program
9 IR SENSOR (AZ1155 models only)
– infrared for remote control
6
Back Panel
17 Telescopic aerial – to improve FM
reception
18 Voltage selector – (inside the battery
compartment, not all versions) adjust to
match the local voltage 110/220V before
plugging in the set
19 AC MAINS – inlet for mains lead
20 Battery door – open to insert 6 x R-14,
UM-2 or C-cells
This set complies with the radio
interference requirements of the
European Community.
AZ 1150 /00
2/8/01 11:21
page
Page 7
7
Digital Remote Control
DIGITAL REMOTE CONTROL
(for AZ1155 model only)
Power Supply
English
AZ1150/00 eng
15 REPEAT – repeats a track/ program/
entire MP3-CD/CD
1 CD – selects MP3-CD/CD sound source
Power Supply
2 y – switches the set to standby
Whenever convenient, use the mains
supply if you want to conserve battery life.
Make sure you remove the plug from the
set and wall socket before inserting
batteries.
4 SHUFFLE – plays all MP3-CD/CD tracks
in random order
5 BASS – selects ULTRABASS 2 on/off
6 2; – starts MP3-CD/CD playback
– pauses MP3-CD/CD playback
Batteries (not included)
1 Open the battery compartment and insert
six batteries, type R-14, UM-2 or C-cells,
(preferably alkaline) with the correct
polarity as indicated by the "+" and "–"
symbols inside the compartment.
AC MAINS
3 + VOLUME - – adjusts volume level (up
down)
7 SEARCH 5 , 6 – fast searches
backwards, forwards within a track
8 BAND – selects FM/ MW(AM)/LW
waveband (LW not on all versions)
6 x 1.5V R14/ UM2/ C CELL
9 PRESET 3 , 4 (up, down)
MP3-CD : selects an album
TUNER : selects a preset radio station
10 TUNING ∞ , § (down, up) – tunes to
tuner stations
• Remote control (AZ1155 model
only)
11 TUNER – selects tuner sound source
12 9 – stops MP3-CD/CD playback;
– erases a MP3-CD/CD program
13 ¡ , ™ – skips to the beginning of a current
track previous/ subsequent track
14 MUTE – interrupts/ resumes sound
Open the battery compartment and insert
2 batteries, type AAA, R03 or UM4
(preferably alkaline).
7
AZ1150/00 eng
2/8/01 11:21
AZ 1150 /00
page
Page 8
8
Power Supply
Batteries contain chemical substances,
so they should be disposed of properly.
Incorrect use of batteries can cause
electrolyte leakage and will corrode the
compartment or cause the batteries to
burst.Therefore:
• Do not mix battery types: e.g. alkaline with
carbon zinc. Only use batteries of the same
type for the set.
2 Connect the mains lead to the MAINS inlet
and the wall socket.The mains supply is
now connected and ready for use.
3 To switch off completely, withdraw the
mains lead from the wall socket.
• Disconnect the mains lead from the wall
socket to protect your set during heavy
thunderstorms.
The type plate is located on the
bottom of the set.
Switching power on/off:
Save energy
To avoid unnecessary energy consumption
always press the POWER button to off
after using the set.
• When inserting new batteries, do not try
to mix old batteries with the new ones.
S
S
2
LT
R
A
M
V
OL
R
WE
PO
Using AC Mains
A
B
U
• Remove the batteries if the set is not to be
used for a long time.
E
W
B AT T
.
UM
LO
S
O
1 Check if the mains voltage, as shown on
the type plate located on the
bottom of the set, corresponds to your
local mains supply. If it does not, consult
your dealer or service centre.
AC MAINS
English
2 Replace the compartment door, making
sure the batteries are firmly and correctly
in place.The set is now ready to operate.
➜ If LOW BATT lights up, battery power
is running low.The LOW BATT indicator
eventually goes out if the batteries are
too weak.
U
R
• The display backlight only operates when
using AC mains supply.
Standby power consumption..........................≤ 2 W
MP3-CD PLAYBACK
8
page
Page 9
9
General operation
Digital Tuner
General operation
English
AZ 1150 /00
2/8/01 11:21
Tuning to Radio Stations
A
B
AZ1155
S
S
CD RADIO SOUNDMACHINE
2
ME
W
OP
B AT T
.
A
LT
R
U
LU
LO
M
WER
S
S
PO
A
B
M
B
A
N
R
A
MP3 CD PLAYBACK
D
AZ1150/00 eng
EN
L
•C
O
SE
S
O
R
C
R
WE
PO
U
L T
A
O
NE
R
LBUM
T
A
ALBUM
B AT T
E
S
SE
.
W
A B A S S 2 • D I G I TA
PR
LO
E
R
E
E
V
UM
D
D
E
U LT R
OL
R
G
P
O
M
C
U
ET
PR
ROTARY
NAVIGATIO
N
S
O
U
R
C
E
U LT R
1 Press the POWER button.
1 Press the POWER button.
2 To select sound source, press SOURCE
once or more.
2 Press SOURCE once or more to select
TUNER.
➜ Display: shows waveband, frequency /
and preset station number if already
stored.
3 Adjust the sound with the VOLUME and
ULTRABASS 2 controls.
➜ Volume level is briefly shown as a
number 0-32, during volume adjustment.
The volume bar is shown during
operation.
➜ ULTRABASS 2 indicator lights up
when activated.
MUTE: AZ1155 model only
• Press MUTE on the remote control to
interrupt sound reproduction instantly.
➜ Playback continues without sound.
• To reactivate sound reproduction you can:
– press MUTE again;
– adjust the volume controls;
– change source.
4 To switch off the set, press POWER.
Note: When the set is switched off, the set's
memory will retain:
– the tuner presets;
– the sound settings and up to volume level
20 (maximum).
MP3-CD PLAYBACK
3 Press BAND once or more to select the
desired waveband.
MP3-CD PLAYBACK
4 Tuning to stations: you can tune to your
stations manually or by automatic search
tuning:
Automatic search tuning:
• Gently turn and hold the ROTARY
NAVIGATION ring anti-clockwise or
clockwise to ¡ or ™ , and release when the
frequency in the display starts to change.
➜ The radio automatically tunes to a
station of sufficient reception. Display
shows Sr ch during automatic tuning.
CAUTION
Use of controls or adjustments or
performance of procedures other
than herein may result in hazardous
radiation exposure or other unsafe
operation.
9
AZ1150/00 eng
AZ 1150 /00
2/8/01 11:21
page
Page 10
10
Digital Tuner
• Repeat the above until you reach the
desired frequency.
To improve reception
• For FM, pull out the telescopic aerial.
Incline and turn the aerial. Reduce its length
if the signal is too strong (very close to a
transmitter).
➜ Display shows stereo if FM station is
received in stereo.
Automatic programming will start with a
chosen preset number. From this preset
number upwards, former programmed
tuner stations will be replaced.The unit will
only program stations which are not in the
memory already.
1 Press ALBUM, PRESET + or - once or
more (¡ or ™ on the remote control) to
select the preset number where
programming should start.
M
• Gently turn the ROTARY
NAVIGATION ring to 5 or 6 , and
then release.
Autostore
OP
EN
L
•C
O
SE
R
A
G
P
O
D
R
O
E
M
C
U LT R
U
L T
NE
R
LBUM
FM
MW
(AM)/LW
S
SE
PR
E
D
T
ALBUM
A B A S S 2 • D I G I TA
A
• For MW(AM)/LW the set is provided with
a built-in aerial so the telescopic aerial is
not needed. Direct the aerial by turning the
whole set.
E
English
Manual tuning:
ET
PR
Note: If no preset number is selected, default
is preset 1 and all your presets will be
replaced.
MP3-CD PLAYBACK
5 To switch off the tuner, press POWER.
Programming tuner stations
Store up to 30 tuner stations in the
memory, manually or automatically.You can
also erase a preset station by storing
another frequency in its place.
10
2 Press PROGRAM for more than 2
seconds to activate programming.
➜ Display shows 'A' (autostore) and
'Sr ch' and available stations are
programmed in order of waveband : FM,
followed by MW (AM), and then LW
stations (LW not on all versions) The last
preset automatically stored will then be
played.
AZ 1150 /00
2/8/01 11:21
page
Page 11
11
Digital Tuner
Manual programming
1 Tune to your desired station (see Tuning to
radio stations).
2 Press PROGRAM to activate
programming.
➜ Display: program flashes.
MP3-CD Playback
English
AZ1150/00 eng
MP3-CD Playback
IMPORTANT SPECIFICATIONS
Supported formats:
• Disc format ISO9660, Joliet and multisession CDs. Use ISO9660 disc format
when burning CD-ROM.
• MP3 music format.
3 Press ALBUM, PRESET + or - once or
more to allocate a number from 1 to 30 to
this station.
4 Press PROGRAM again to confirm.
➜ Display: program disappears, and
shows the preset number, waveband and
the frequency.
5 Repeat the above four steps to store other
stations.
• MP3 bit rate (data rate): 32-320 Kbps and
variable bit rate.
• 650Mb and 700Mb CD-Rs.
• Directory nesting up to a maximum of 8
levels (max. 64 characters).
General information
The music compression technology MP3
(MPEG Audio Layer 3) reduces the original
digital audio data by a factor up to 10
without losing significant sound quality.This
allows you to record up to 10 hours of
CD-like quality music on a single CD-ROM.
How to get MP3 music
Environmental information
All redundant packaging has been omitted.
We have done our utmost to make the
packaging easily separable into three
materials: cardboard, polystyrene foam and
polyethylene.
Your set consists of materials which can be
recycled if disassembled by a specialized
company. Please observe the local regulations
regarding the disposal of packaging, exhausted
batteries and old equipment.
Either download legal music files from the
internet to your computer harddisc or
create them from your own audio CDs.
For this, insert an audio CD into your
computer´s CD-ROM drive and convert
the music using an appropriate encoder
software.To achieve a good sound quality, a
bit rate of 128 kbps or higher is
recommended for MP3 music files.
Some encoder software offers an option to
protect music files, i. e. the files can only be
played on the computer which created
them. If you burn such files on a CD-ROM,
11
AZ1150/00 eng
AZ 1150 /00
2/8/01 11:21
page
Page 12
12
MP3-CD Playback
English
you cannot play them on this set. Make sure
to deactivate the protection option in the
encoder software before creating the music
files. In this case you are responsible for
adherence to all local or international
copyrights.
When burning the MP3-CD
• Make sure the file names of the MP3 files
end with .mp3.
For example:
001-ONEWORLD.MP3
002-FIRESTARTER.MP3
003-DEEP.MP3.
• There may be an album 00 which will be
played before all other albums. Album 00
contains all tracks which you did not put
into an album.
• MP3-CD albums and titles are shown as
numbers in the display.
• Multi-session recording & playback: For
playback of the last session on multi-session
CDs, make sure you have recorded more
than 1 track or title in the last session.
• Make sure you close the session.
How to organize MP3 files
IMPORTANT!
•
•
•
•
MP3CD
album
title
•
•
You can store up to a maximum number of
40 albums and 400 titles on one MP3-CD.
In order to easily handle the large number
of music files on a CD-ROM,
you can organize them in folders
(“albums”).
The tracks of an album will be played in
alphabetical order. If you want to arrange
them in a certain order, let the file names
start with numbers.
12
•
This set does not play/support the
following:
UDF disc format.
Non-finalized CD-Rs and CD-RWs.
Mixed CD format recordings e.g. CD audio
and MP3 tracks combined within a CD-R.
Empty albums: an empty album is an album
that does not contain MP3 files, and will
not be shown in the display.
Non-supported file formats are skipped.
This means that e.g.: Word documents .doc
or MP3 files with extension .dlf are ignored
and will not be played.
Playlist Files e.g. .m3u, .pls of WMA, AAC,
Winamp, Sonic, RealJukebox, MS
Mediaplayer 7.0, MusicMatch.
Recordings created on e.g. DirectCD,
PacketWriting and Package Writing.
AZ1150/00 eng
AZ 1150 /00
2/8/01 11:21
page
Page 13
13
MP3-CD/CD PLAYER
Playing MP3-CD/CD
Display indication for MP3-CD/CD
functions:
This CD player plays Audio Discs including
CD(-R)s, and MP3 CD-ROMs.
WER
PO
OL
V
W
OP
B AT T
.
E
EN
L
•C
O
SE
O
M
C
S
O
program
repeat all
UM
LO
CD
English
MP3-CD/CD Playback
U
R
C
D
E
U LT R
L
A B A S S 2 • D I G I TA
NE
R
LBUM
S
E
E
SE
PR
T
A
ALBUM
TU
ET
PR
ROTARY
NAVIGAT
ION
MP3-CD PLAYBACK
– OPEn: CD door open
– rEAd: when reading disc contents
– MP3CD: when an MP3-CD ROM is
inserted
– CD: when an audio CD is inserted
– MP3-CD in stop mode: total album
number and total title number
– CD in stop mode: total track number
and total playback time
– During MP3-CD/CD playback:
elapsed playback time of current album
and title number/ current track number
– PAUS: when playback on pause mode
– SHUFFLE/ REPEAT modes: when
the respective mode is activated
– program: when CD program active
– Prog also appears briefly when you
store a title/ track
– no SEL: program activated but no title/
track selected
– FULL: program memory full
– no album: ALBUM, PRESET + or pressed during playback of MP3-CD or
CD containing no album arrangement
– CdEr, no Cd or nF Cd: error / no
disc inserted/ the CD(-R) is blank/ disc is
not finalized (see Troubleshooting)
• CD-I, CDV,VCD, DVD, however, are not
possible.
1 Press the POWER button.
2 Press SOURCE once or more to select
MP3-CD/CD.
3 To open the CD door, lift the CD door at
the edge marked OPEN•CLOSE.
4 Insert a CD(-R) with the printed side facing
up and close the CD door.
5 Press 2; to start playback.
6 To pause playback press 2;.To resume,
press 2; again.
7 To stop, press 9.
8 To switch off the set, press POWER.
Note: MP3-CD/CD playback will also stop
when:
– you press the CD door open;
– you select TUNER source;
– the disc has reached to the end.
13
AZ1150/00 eng
2/8/01 11:21
AZ 1150 /00
page
Page 14
14
MP3-CD/CD Playback
English
Selecting a different track
ES
+
S
ALBUM
-
PR
U
ALB M
ET
Depending on whether you're listening to
MP3 or CD Audio, during playback simply
use ROTARY NAVIGATION (or ¡ or
™ buttons on the remote, AZ1155 only) to
select a particular track.
– If you have selected a track number in
the stop or pause position, press 2; to
start playback
ET
PR
E
ROTARY
NAVIGATION
MP3CD
album
title
Finding a passage within a track
1 Gently turn the ROTARY
NAVIGATION ring anti-clockwise or
clockwise to 5 or 6, (or 5 or 6
buttons on the remote, AZ1155 only) and
hold.
➜ No sound is heard during MP3 fast
cue/review.
➜ The CD is played at high speed and low
volume.
2 When you recognize the passage you want
release the ROTARY NAVIGATION ring.
➜ Normal playback resumes.
Note: Searching is not possible if you are
playing MP3 files encoded with variable bit
rate (VBR).
• MP3-CD mode only:
First press ALBUM, PRESET + or once or more to find your album.Then
follow the next 2 steps.
MP3-CD PLAYBACK
Different play modes : Shuffle
and Repeat
CD MODE allows you to select various
play modes.The modes can be selected or
changed during MP3-CD/CD playback:
MP3-CD/CD:
B
A
N
D
PLAYB ACK
M
1 Gently turn the ROTARY
NAVIGATION ring anti-clockwise or
clockwise to ¡ or ™, (or ¡ , ™ buttons on
the remote, AZ1155 only).
OP
EN
L
•C
O
SE
R
A
G
P
O
D
R
O
E
M
C
2 Release the ROTARY NAVIGATION
ring when you reach the desired track.
I G I TA
U
L T
NE
D
R
SHUFFLE – all tracks are played in
random order
SHUFFLE REPEAT ALL – repeats the
entire MP3-CD/CD in random order
REPEAT – plays the current track
continuously
14
MP3-CD PLAYBACK
AZ1150/00 eng
AZ 1150 /00
2/8/01 11:21
page
Page 15
15
CD:
REPEAT ALL – plays the whole
MP3-CD/CD continuously
1 During playback, select your play mode by
pressing CD MODE once or more until
the desired play mode is shown.
• The SHUFFLE/ REPEAT play options
can be combined and used with a program:
e.g. SHUFFLE REPEAT ALL - repeats
the entire program in random order.
2 To return to normal playback press CD
MODE until the various SHUFFLE/
REPEATmodes are no longer shown.
• You can also press 9 to quit the play
mode.
Programming track numbers
You may store up to 30 tracks in the
desired sequence. If you like, store any
track more than once.
• First use the ROTARY NAVIGATION
(or ¡ or ™ buttons on the remote,
AZ1155 only) to select a particular track.
2 When your chosen track number appears,
press PROGRAM once to store the
track.
➜ Display shows program and 'Prog'
briefly followed by your selected track
number.
➜ If you attempt to program without first
selecting a track number, no SEL is
shown.
3 Repeat steps 1 and 2 to select and store
all desired tracks in this way.
➜ FULL is displayed if you attempt to
program more than 30 tracks.
4 To play your program, press 2;.
To review a program
•
1 In the stop position, first select your album
and tracks as follows:
MP3-CD only:
• press ALBUM, PRESET + or - once or
more to find your album.
•
Turn the ROTARY NAVIGATION anticlockwise or clockwise (or ¡ or ™ buttons
on the remote, AZ1155 only) to select a
particular track.
➜ Display: album/ title flashes if you have
not made the respective selection.
In the stop position, press and hold down
PROGRAM for more than 2 seconds.
➜ Display shows all your stored track
numbers in sequence, or the MP3-CD
title and album numbers.
➜ Display shows 'no Pr' if no title/track
programmed.
Erasing a program
You can erase the contents of the memory
by:
– opening the CD door;
– selecting TUNER source;
– pressing 9 twice during playback/ in the
stop position
• Continue with the following, steps 2-4.
15
English
MP3-CD/CD Playback
AZ1150/00 eng
AZ 1150 /00
2/8/01 11:21
page
Page 16
16
Maintenance
English
Precautions &
General Maintenance
MP3-CD player and CD
handling
• Place the set on a hard and flat surface so
that the system does not tilt.
• The lens of the CD player should never be
touched!
• Do not expose the set, batteries or CDs to
humidity, rain, sand or excessive heat
caused by heating equipment or direct
sunlight.
• Sudden changes in the surrounding
temperature can cause condensation to
form and the lens of your CD player to
cloud over. Playing a disc is then not
possible. Do not attempt to clean the lens
but leave the set in a warm environment
until the moisture evaporates.
• Do not cover the set. Adequate ventilation
with a minimum gap of 6 inches between
the ventilation holes and surrounding
surfaces is necessary to prevent heat buildup.
• The mechanical parts of the set contain
self-lubricating bearings and must not be
oiled or lubricated.
• To clean the set, use a dry cloth. Do not
use any cleaning agents containing alcohol,
ammonia, benzene or abrasives as these
may harm the housing.
• Always shut the CD door to keep the CD
compartment dust-free.To clean, dust the
compartment with a soft dry cloth.
• To take a disc out of its box, press the
centre spindle while lifting the disc. Always
pick up the disc by the edge and replace
the disc back in its box after use to avoid
scratching and dust.
• To clean the disc, wipe in a straight line
from the centre towards the edge using a
soft, lint-free cloth. Do not use cleaning
agents as they may damage the disc.
• Never write on a disc or attach any
stickers to it.
16
AZ1150/00 eng
AZ 1150 /00
2/8/01 11:21
page
Page 17
17
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer
or service centre.
WARNING: Do not open the set as there is a risk of electric shock. Under no
circumstances should you try to repair the set yourself, as this will invalidate the
guarantee.
Problem
Solution
No sound / No power
– Volume not adjusted. Adjust the VOLUME
– Mains lead not securely connected. Connect AC mains
lead properly
– Batteries exhausted /incorrectly inserted. Insert (fresh)
batteries correctly
Display does not function
properly/ No reaction to
operation of any of the
controls
– Electrostatic discharge
Switch off and unplug the set. Reconnect after a few
seconds.
Err, no Cd or nF dISC
indication
– No CD inserted. Insert a CD
– CD damaged or dirty. Replace/ clean CD (see
maintenance)
– Laser lens steamed up. Wait until lens has cleared
– CD-(R) is blank or the disc is not finalized. Use a
finalized CD-(R)
The CD skips tracks
– Disc damaged or dirty. Replace or clean disc
– SHUFFLE or a program is active
Quit SHUFFLE / program mode(s)
Sound skips during
MP3 playback
– MP3 file made at compression level
exceeding 320kbps
Use a lower compression level to record CD tracks into
MP3 format
– Disc damaged or dirty. Replace or clean disc
Cannot find desired
MP3 track
– Wrong file extension used
save file as .MP3
17
English
Troubleshooting